21/05/2018 Material Science and Engineering - - Unit 4 - Week 3.
Defects, diffusion and phase diagram
[email protected] ▼
Courses » Material Science and Engineering
Announcements Course Ask a Question Progress Mentor
Unit 4 - Week 3.
Defects, diffusion and phase diagram
Course
outline Assignment 3
The due date for submitting this assignment has passed. Due on 2018-02-28, 23:59 IST.
How to access
the portal Submitted assignment
Week 1. Lattice, 1) What is the ratio of equilibrium concentration of vacancies in aluminium and 1 point
Crystal nickel at 300 K given ΔHf(Al) = 68kJ/mol, ΔHf(Ni) = 168kJ/mol :
structures, Miller
indices for 2.6 x 1017
planes and
directions 2.6 x 1016
2.6 x 1018
Week 2. None of the above
Microscopes,
microstructures No, the answer is incorrect.
and quantitative
Score: 0
metallography
Accepted Answers:
Week 3. Defects, 2.6 x 1017
diffusion and
phase diagram 2) A cation vacancy and an anion vacancy in a crystal of the type AB is called: 1 point
Lesson 1. Schottky defect
Crystallographic
defects
Frenkel defect
Pair of vacancies
Lesson 2.
Diffusion
None of these
Lesson 3. No, the answer is incorrect.
Phase diagram Score: 0
1
Accepted Answers:
Lesson 4. Schottky defect
Phase diagram
2 3) The t vector is parallel to the b vector in a dislocation of the type: 1 point
Lesson 5. Screw
Eutectic phase
diagram Edge
Mixed
Feedback
week-3 None of these
Quiz : No, the answer is incorrect.
Assignment 3 Score: 0
Hints and Accepted Answers:
Solutions Screw
Week 4. 4) At 950° C, a 0.8% carbon steel is getting decarburized for a duration of 4 hr in 1 point
Equilibrium an atmosphere equivalent to 0% carbon at the surface of the steel. Determine the
phase diagram,
iron-carbon
https://onlinecourses.nptel.ac.in/noc18_mm05/unit?unit=17&assessment=80 1/4
21/05/2018 Material Science and Engineering - - Unit 4 - Week 3. Defects, diffusion and phase diagram
phase diagram, minimum depth up to which post-machining is to be done, if the carbon content at the
lever rule, phase
surface after-machining should not be below 0.6%.
transformation
0.55mm
Week 5. TTT and
CCT curves, heat 0.65mm
treatments, 0.75mm
Introduction to 0.85mm
mechanical
properties No, the answer is incorrect.
Score: 0
Week 6.
Mechanical Accepted Answers:
behaviour of 0.75mm
materials,
strengthening 5) Which of the following elements have the highest diffusion coefficient in steel: 1 point
mechanism
Mg
Week 7. W
Strengthening Ti
mechanism,
fracture and C
fatigue
No, the answer is incorrect.
Score: 0
Week 8. Creep,
ceramics and Accepted Answers:
plastic, NDT C
techniques, alloy
designation 6) Which of the following is the fastest diffusing species in iron: 1 point
DOWNLOAD H
VIDEOS N
C
W
No, the answer is incorrect.
Score: 0
Accepted Answers:
H
7) At atmospheric pressure, a random material is showing 5 phases in equilibrium 1 point
at 1000K. What is the minimum number of components in the system?
3
4
5
2
No, the answer is incorrect.
Score: 0
Accepted Answers:
4
8) In a single-component system, the maximum number of phases that can coexist 1 point
together in equilibrium is:
2
3
4
5
No, the answer is incorrect.
Score: 0
Accepted Answers:
3
9) The degree of freedom when ice, water, water vapour co-exist in equilibrium is: 1 point
https://onlinecourses.nptel.ac.in/noc18_mm05/unit?unit=17&assessment=80 2/4
21/05/2018 Material Science and Engineering - - Unit 4 - Week 3. Defects, diffusion and phase diagram
1
Triple point
0
-1
No, the answer is incorrect.
Score: 0
Accepted Answers:
0
10)How many phases are present in an isomorphous phase diagram? 1 point
1
2
3
4
No, the answer is incorrect.
Score: 0
Accepted Answers:
2
11)Relative amounts of phases in a region can be deduced using 1 point
Phase rule
Lever rule
Either
None
No, the answer is incorrect.
Score: 0
Accepted Answers:
Lever rule
12)If the fraction of liquid with 60% B, which is in equilibrium with solid of 82% B is 1 point
0.6, then the overall composition is:
0.5
74.5% B
69% B
25% B
No, the answer is incorrect.
Score: 0
Accepted Answers:
69% B
13)What is the name of the reaction when one solid splits into two solids on 1 point
cooling:
Eutectoid
Eutectic
Peritectic
Peritectoid
No, the answer is incorrect.
Score: 0
Accepted Answers:
Eutectoid
14)In the eutectic phase diagram of Ag-Cu system, the solubility limit at 500° C of 1 point
copper is 3% in the Ag-rich phase and of Ag is 2% in the Cu-rich phase. In sterling
silver(92.5% Ag - 7.5% Cu), the percent of copper in the Ag-rich phase at 500° C is:
https://onlinecourses.nptel.ac.in/noc18_mm05/unit?unit=17&assessment=80 3/4
21/05/2018 Material Science and Engineering - - Unit 4 - Week 3. Defects, diffusion and phase diagram
95.26
4.74
3
98
No, the answer is incorrect.
Score: 0
Accepted Answers:
3
Previous Page End
© 2014 NPTEL - Privacy & Terms - Honor Code - FAQs -
A project of In association with
Funded by
Powered by
https://onlinecourses.nptel.ac.in/noc18_mm05/unit?unit=17&assessment=80 4/4
