Introduction

Contents
• aRacer Website
• RC Mini X vs RC Super X
• RC Super X System introduction
• RC Super X ECU wiring diagram
• Speed Tuning X Introduction
• ECU Data Log
• iView X Introduction
• Speed Turning X Semi-AutoTune
• Speed Turning X AutoTune
• SuperX ECU .asx File Version Upgrade
• Super2 and SuperX calibration differences
aRacer Website
Url https://www.aracer-speedtek.com/index.php?lang=en

Q&A Software
User
Manual
RC Mini X vs RC Super X
RC Mini X RC Super X
ECU Type Standalone Standalone

ECU log V (20 para. by X Tune App) V (All engine data in 60min
record by cycle)
Fuel table 20 x 17 56 x 25

SA table 20 x 9 40 x 17

Auto Tune TPS VM 20 x 17 AP & TPS VM 56 x 25

(In-App purchasing)
Semi Auto Tune X V

Support race module X V

Tuning parameters Over 20 Over 80

Backfire In-App purchasing V

Launch control In-App purchasing (Basic) V (Advance)

Pit limit In-App purchasing V

Traction Control In-App purchasing (Basic) V (Advance)

Dual injector X In-App purchasing

Turbocharge X In-App purchasing

NOS X In-App purchasing

 RC SuperX System introduction

Speed Turning X
WiFi or ProLink
1. Crank Angle(CRK) 1. Fuel Injection Pulse
2. Manifold Air Temp(T_Air) 2. Spark Angle(SA)
3. Engine Coolant Temp(T_Eng) 3. Fuel Pump Pulse
4. Manifold Air Pressure(Eng_AP) 4. Idle Speed Valve(ISC)
5. Throttle Position(TPS_indx) 5. O2 Heater
6. O2 signal (NBO2_Volt)(AFR_WBO2) 6. Malf-Detect Light
7. Generator Voltage(Volt_Batt_indx) 7. RPM Meter
8. Rollover Switch (D1Rollover_ Selection) 8. Water Temp Warning
9. Vehicle Speed(Vehicle Speed) 9. Day Light Relay
10. VVA control

Gyro module
iMode 4X
Race Function
Logger 2.5 Race Panel
Module 2.5 AF2
eRacing Battery Quick Shift
Module

aRacer QSR
GPS Quick Shift Sensor
Wide Band
Race Switch
O2 sensor
 Logger Module 2.5

Support all aRacer ECU, and can be extended any aRacer function modules

Key features:

• Can record 50 hours data

• 5 groups of analog input

• Can record more than 100 Engine parameters

and additional external sensor signal data
 Function Box 2.5

Support all aRacer ECU, and can be extended any aRacer function modules

Key features:
• GPS track analysis
• With lap time function
• Gyro function/G value analysis/Inclination
calculation
• With Racing switch function (Map switch/Pit
limit/Launch mode)
 Race Panel

Key features:
• Over 20 engine data can be monitored
• RPM indicator, and can be set up
• Time tracking by real time ( Race function box is necessary)
• Shift indicator
• 3 map can be switched, pit limited and launch control switch ( Race function
box is necessary)
• Scratch resistant, small size design, water resistant
AF2

Optimal Design for AF2:

• Volume reduce 38%
• Weight lower 53%
• Performance up!!!
• Simple wire connection
• Bosch LSU 4.9 wideband oxygen sensor include
Response +37.5%
• Minimum operating voltage lower to 8.5 V
• Measurement accuracy up 80%
• Heating power consumption reduce 25%
• Maximum operation voltage increase 5%
• Lifecycle increase 56%
• Ｗarm up time faster 50%
iMode 4X

New features3-segment map switching

• ECU log memory cycle switch
• ECU log memory clear switch
• Unit switching

Add display item

• Added display screen quick switch Sty1 / 2
• Added MGU eBoost display
• Gear display
• Map display
aRacer QS-Racing Two Way Quick Shifter

• It can reduce the shift timing 60% up

• Two way quick shifter sensor, easy to install & set

• Support RC Super/Mini X ECU

• There are many detail functions can be adjusted In RC

Super/Mini X ECU
eRacing Battery
RC SuperX ECU wiring diagram

1 2 3 Hs Can connector 6pin

1. LS Can lo (Yellow)
2. GND (Black)
3. LS Can hi (Blue)
4. HS Can hi (White)
5. HS Can lo (Orange)
4 5 6 6. ECU 12V (max 500mA) (Red)
Ls Can connector 4pin
1 2 1. GND (Black)
2. Ls Can hi (Blue)
3. Ls Can lo (Yellow)
4. IGN 12V (Pink)
3 4
1 2 Quick Shifter connector 4pin
1. IGN 12V (Pink)
2. Second injector (Purple)
3. GND (Black)
3 4 4. QuickShift AD (Gray)
RC SuperX ECU wiring diagram

Second Injector

aRacer QSR Quick Shifter

or

AF2 Module

or

Speed Turning X

iMode 4X
RC SuperX ECU wiring diagram
1to 5 Extend Cable

AF2_A Module
aRacer QSR
Quick Shift

AF2_B

ECU
Spare

ECU

ProLink
iMode 4X / Sport D
 RC Super X ECU wiring diagram
1to10 Extend Cable
AF2_A
aRacer QSR
Quick Shift

AF2_B

Knock Module
ProLink
1to10 Extend Cable

Spare

Gyro
Race Panel

Spare

Rear of bike Logger 2.5

GPS
CAN bus output

Pin2:CAN High(blue)
Pin3:CAN Low(yellow)
Race Module 2.5 Front of bike Race Switch
Download Speed Tuning X ecu Software

Download from aRacer website

https://www.aracer-speedtek.com/download.php?lang=en&tb=1
 Speed Tuning X Introduction
Regional format
Some Indonesia notebook will have wrong number display in table value.
Please set the regional format English.
Speed Tuning X Introduction
open software

Click the button to open Speedtuning X

 Speed Tuning X Introduction
Interface
Quick Burn Select connect port
AutoTune
Flash Map Link or Unlink ecu
Save Map
Open Map ECU data log
iView X

Calibration
Start
monitor
Informations

Calibration

Monitor
Malf.code

Monitor area

Calibration Panel Parameters description

Track setting

ECU connection status AutoTune status

Map Number
 Speed Tuning X Introduction
Cell track Semi-AutoTune
Scope track
Synchronize with iView
Scale Setting Show A/F

Send data
Value calculate
Read data
 Speed Tuning X Introduction
Scope track

Set the parameter with scope track

Speed Tuning X Introduction

Show A/F

Show A/F at the engine operating range

Speed Tuning X Introduction
Connect to ecu
Connect to ECU through Wi-Fi AP
QB Flash
ECU Upgrade
Tuning ECU
Transfer asx file version
Mobile connect to WIFI AP

Connected to ECU by Wi-Fi directly

iPhone QB Flash with 4/5G (PC, Android )
iPhone ECU Upgrade with 4/5G (PC, Android )
Tuning ECU
Transfer asx file version

Connect to ECU by ProLink

QB Flash
ECU Upgrade
Tuning ECU
Transfer asx file version
 Speed Tuning X Introduction
Connect to ecu
Select aRacer ECU by WiFi or ProLink Connect to ECU

If open ASX file, SpeedTuning X will only link to

the same model.
If you need to change bike model, just open
SpeedTuning X, do not open the ASX file.

• SpeedTurning X can link with Super X ecu by WiFi or ProLink

• The product page of the aRacer website has detailed instructions.
 ProLink Connection

Select ProLink Click this button to connect to ecu

Wi-Fi Connection
 Wi-Fi Connection

If you connect to the ECU by Wi-Fi directly, PC can not

access the Internet at the same time.

ECU upgrade function

Quick Burn
Transfer asx file version
Tuning the ECU
Wi-Fi Connection
Wi-Fi Connection
Wi-Fi Connection
Wi-Fi Connection
 Wi-Fi Connection

ECU upgrade function

Quick Burn
Transfer asx file version
Tuning the ECU
Wi-Fi Connection
Wi-Fi Connection
 Speed Tuning X Introduction
ECU name settings

Change ECU Wi-Fi name

Clear Wi-Fi password

Turn On or Off Wi-Fi

If there is no Prolink, wide open the accelerator for function
one minute immediately after turning on the key,
and the wifi password can be cleared.
 Speed Tuning X Introduction
Wi-Fi Q&A

1. Unable to update ECU software using QB.

• If the PC is directly connected to the ECU, the PC cannot access the Internet via Wi-Fi. Please
download the QB data before connecting.​
• Use the network AP method to download QB online.​
• The asx file of the ECU does not match the opened asx file that can’t be connected to flash. Just
close the asx file and open the QB to flash the target bike model.

2. Manually clear Wi-Fi password function.

• Key On and Stall, full throttle for 60sec.​
• Open the SpeedTuningX using Pro-Link, go to "Settings" ⇨ "ECU Name Setting" ⇨ "Wi-Fi
Factory reset“.​
 Speed Tuning X Introduction
Quick Burn(Cloud database) flash Super X ECU
1. Open Quick Burn 2. Download all YAMAHA base map in cloud 5. Flash Map

4. Select Spec.

3. Select Model

• Quick Burn will filter the bike model when link with ecu.
• Quick Burn can not download the base map when link with Super X ecu by WiFi.
• Click the download button before link with ecu by WiFi
Speed Tuning X Introduction
Save the Base Map for Tuning
Save Calibration Map file
Speed Tuning X Introduction
Transfer calibration file form Super2 to SuperX
Step2 Click the button and select the am2 file to transfer to
asx file

Step1 Connect to internet and download QB

maps.
Speed Tuning X Introduction
Dynamic Chart

Show the monitor data in chart

Speed Tuning X Introduction
aRacer Online

TeamViewer Online Support

Speed Tuning X Introduction
ECU information

V：ECU version
S：ECU sox version
C：Calibration version
A：ASX file version

Click the button to update SpeedTuning X

 Speed Tuning X Introduction
Malf. code
Connect to ecu

Malf. code
Show the malf. code of ecu
Speed Tuning X Introduction
Module List
 SuperX ECU Module Update

Update by ProLink

Update by Wi-Fi

Update by ProLink

Update by ProLink

Update by ProLink
When aRacer modules are connected to
the ECU, the firmware can be updated Update by ProLink
through ProLink(ECU Wi-Fi through Wi-
Fi to update firmware).

When updating, other modules must be

removed to avoid update failure.
 iView X Introduction
Parameters list
Reset logdata GPS Path
Zoom in Synchronize with SpeedTuning X
Zoom out Always Top
Open log Show A/F
data
iView X Introduction
iView Synchronize with D3Cyl1_VM map

SpeedTuning show wide band data at D3Cyl1_VM

 iView X Introduction
Semi-AutoTune (D3Cyl1_VM)
Click AFR analysis button to show A/F to D3Cyl1VM

SpeedTuning show wide band data at

D3Cyl1_VM

Right click to remove the area which you don’t want to Semi-AutoTune.
iView X Introduction
Semi-AutoTune (D3Cyl1_VM)
D3Cyl1_VM value is automatically modified when the button is pressed
After the function is executed once, the button is dimmed.
iView X Introduction
Semi-AutoTune (D3Cyl1_VM_TPS_F )

iView Synchronize with D3Cyl1_VM_TPS_F table

 iView X Introduction
Semi-AutoTune (D3Cyl1_VM_TPS_F )
Click AFR analysis button to show A/F to D3Cyl1VM_TPS_F

SpeedTuning show wide band data at

D3Cyl1_VM_TPS_F

Right click to remove the area which you don’t want to Semi-AutoTune.
iView X Introduction
Semi-AutoTune (D3Cyl1_VM_TPS_F )
D3Cyl1_VM_TPS_F value is automatically modified when the button is pressed
After the function is executed once, the button is dimmed.
Speed Tuning X AutoTune
Left click to turn On / Off AutoTune Select AutoTune Table
Right click to open AT setting quickly.

AP Base TPS Base

Set the Exhaust pipe length from cylinder

ex valve to O2 sensor to calculate the O2
sensor delay time.
 Speed Tuning X AutoTune

AT_ON  AT Function is turned on but conditions aren’t ready. Ex: engine temp. too cold(<60℃), Malf. Code, TPS change quickly
 Speed Tuning X AutoTune

AT_ON  AT Function is turned on but conditions aren’t ready. Ex: engine temp. too cold(<60℃), Malf. Code, TPS change quickly
Speed Tuning X AutoTune
After auto-tuning is complete, press Save button to save the value to ASX file
ECU will save the modified value when key off.

AT_Running(AP) AT Function is correcting the D3Cyl1_VM map

 Speed Tuning X AutoTune
Select AutoTune Table

AT_Running(TPS) AT Function is correcting the D3Cyl1VM_TPS_F map

 Speed Tuning X AutoTune
Bypass Area Click to open the AT-AFR result and bypass area.

Bypass Area

Turn On or Off

After the Auto Tune is completed, press the save button to save the value to the ASX file, and the ECU will
store the modified value when it shuts down.
SuperX ECU .asx File Version Upgrade
Version different warning Connect to ECU

You need to connect to Internet to upgrade the file to the same

version which is inside the ECU.
 Super2 and SuperX calibration differences
• Super X ecu cancel the WOT calibration
– D2Race_AFR_Power => D3AFR_1 (index RPM & TPS%)
– D2Race_SA_Power => D3SA_Base (index RPM & TPS%)
– D2Inj_Angle_Power => D3Inj_Angle_Seq_Run (index RPM & TPS%)

• Super X ecu will auto save calibration parameters when key off
power.
Parameters
D3Cyl1_VM
• SA calibration step form 1 CA to 0.25 CA. D3Cyl1_VM_TPS_F
D3SA_Base
D3AFR_1~3
• The axis of the table value can be modified. D3SA_Offset_1~3
D3Inj_Angle_Seq_Run
 Convert Super2 to SuperX ECU

• Transfer calibration file am2(amrc) to

asx(arx).
• Connect aRacer quick shifter to ecu quick
shift connector.
• Update race module to 2.5 version
• Update logger reader software to V2.0.10
• Update lapview pro for V1.0.5