Publication 11 22437 1450

Lecture 2:
Network Connectivity Devices
Assist lecturer : Dr. Suad abdulelah Alasadi

Network Devices- Terminology
 Some terminology related to the operation of network devices is:
- Domain : is a specific part of a network.
- Bandwidth : is the amount of data that can be carried across a network in
a given time period.
- Unicast data: is data meant for a specific device.
- Broadcast data : is data meant for all devices; a special broadcast address
indicates this.
- Multicast data: is data destined for a specific group of devices; a special
address indicates this.
- A bandwidth domain, known as a collision domain for Ethernet LANs,
includes all devices that share the same bandwidth.
- A broadcast domain includes all devices that receive each other’s’
broadcasts (and multicasts)

Network Devices
 Network devices are the devices that interconnect networks.
Because these devices connect network entities, they are
known as connectivity devices. These devices include:
 Network Interface Card (NIC)

 Hub
 Switch
 Bridge
 Router
 Gateway
Network Devices- NIC
 Network Interface Card (NIC)
The network interface card (NIC), as its name suggests, is the
expansion card you install in your computer to connect, or interface,
your computer to the network. This device provides the physical,
electrical, and electronic connections to the network media. A NIC is
either an expansion card (the most popular implementation) or built in
to the motherboard of the computer. NIC provides the physical
interface between computer and cabling.
It prepares data, sends data, and controls the flow of data. It can also
receive and translate data into bytes for the CPU to understand.
Network Devices - Hub
HUB
A typical Ethernet LAN uses unshielded twisted-pair (UTP) cables
with RJ-45 connectors.
 Because these cables have only two ends, an intermediary
device is needed to connect more than two computers. That
device is a hub. Hubs are devices used to link several computers
together.
 A hub works at Layer 1 and connects multiple devices so that
they are logically all on one LAN.
 NOTE: The physical connection point on a network device—a
hub, switch, or router—is called an interface or a port.
 A hub has no intelligence—it sends all data received on
any port to all the other ports. So, devices connected
through a hub receive everything that the other devices
send, whether or not it was meant for them. This process
called broadcasting).
 All devices connected to a hub are in one collision domain
and one broadcast domain.
 Note: A hub just repeats all the data received on any port
to all the other ports; thus, hubs are also known as
repeaters.
Network Devices- Switch
 LAN switches are Layer 2 devices and have some

intelligence—they send data to a port only if the data
needs to go there.
• A device connected to a switch port does not receive any

of the information addressed to devices on other ports.
Therefore, the main advantage of using a switch instead of a
hub is that the traffic received by a device is reduced
because only frames addressed to a specific device are
forwarded to the port on which that device is connected.
Switches read the source and destination MAC addresses in the
frames and therefore can keep track of who is where, and who is
talking to whom, and send data only where it needs to go.
 If the switch receives a frame whose destination address

indicates that it is a broadcast (information meant for everyone)
or multicast (information meant for a group), by default it
sends the frame out all ports (except for the one on which it
was received).
 All devices connected to one switch port are in the same

collision domain, but devices connected to different ports are in
different collision domains. By default, all devices connected to
a switch are in the same broadcast domain.
Network Devices- Bridge
 Bridge is a network device that connects two similar network segments
together. The primary function of a bridge is to keep traffic separated on
both sides of the bridge.
 For example, with 200 people on one Ethernet segment, the performance
will be mediocre, because of the design of Ethernet and the number of
workstations that are fighting to transmit. If you divide the segment into two
segments of 100 workstations each, the traffic will be much lower on either
side and performance will increase.
 The main disadvantage to bridges is that they can’t connect dissimilar

network types or perform intelligent path selection. For that function, you
would need a router.
Network Devices- Bridge
Network Devices - Router
 A router goes one step further than a switch. It is a Layer 3 device
that has much more intelligence than a hub or switch.
 By using logical Layer 3 addresses, routers allow devices on

different LANs to communicate with each other and with distant
devices—for example, those connected through the Internet or
through a WAN.
 The logical Layer 3 addresses is the TCP/IP’s IP addresses..
 The router reads the source and destination logical addresses in the
packets and therefore keeps track of who is where, and who is
talking to whom, and sends data only where it needs to go.
Network Devices - Router
 All devices connected to one router port are in the same
collision domain, but devices connected to different ports are in
different collision domains.
 Routers block broadcasts (destined for all networks) and

multicasts by default; routers forward only unicast packets
(destined for a specific device) and packets of a special type
called directed broadcasts.
Network Devices- Router
 Routers work at the OSI model network layer. The main
functions of a router are first to determine the best path that
each packet should take to get to its destination and second to
send the packet on its way.
 Sending the packet out the appropriate interface, along the best
path, is also called switching the packet because the packet is
encapsulated in a new frame, with the appropriate framing
information.
 Routers are normally used to connect one LAN to another.
Typically, when a WAN is set up, there will be at least two
routers used.
Network Devices - Gateway
 A gateway is any hardware and software combination that

connects dissimilar network environments.
 Gateways are the most complex of network devices because

they perform translations at multiple layers of the OSI
model.
Network Device- Gateway
Thank You

Publication 11 22437 1450

Uploaded by

Copyright:

Available Formats

Publication 11 22437 1450

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Publication 11 22437 1450

Uploaded by

Copyright:

Available Formats

Lecture 2:

Network Connectivity Devices

Assist lecturer : Dr. Suad abdulelah Alasadi

- Domain : is a specific part of a network.

- Bandwidth : is the amount of data that can be carried across a network in

a given time period.

- Unicast data: is data meant for a specific device.

- Multicast data: is data destined for a specific group of devices; a special

address indicates this.

- A bandwidth domain, known as a collision domain for Ethernet LANs,

includes all devices that share the same bandwidth.

- A broadcast domain includes all devices that receive each other’s’

broadcasts (and multicasts)

 Network Interface Card (NIC)

 LAN switches are Layer 2 devices and have some

• A device connected to a switch port does not receive any

 If the switch receives a frame whose destination address

 All devices connected to one switch port are in the same

 The main disadvantage to bridges is that they can’t connect dissimilar

 By using logical Layer 3 addresses, routers allow devices on

 The logical Layer 3 addresses is the TCP/IP’s IP addresses..

 Routers block broadcasts (destined for all networks) and

 A gateway is any hardware and software combination that

 Gateways are the most complex of network devices because

You might also like