Scribd Logo
Upload

Welcome to Scribd!

  • 119 views

    Step by Step For Zte Onu Config

    Uploaded by

    femi.jerry2
    The document provides instructions for configuring a new ONU on an OLT, including checking for the available ONU slot on the appropriate PON, entering configuration mode and assigning details like the ONU number, serial number, bandwidth profile, VLAN tagging, and verifying the ONU power levels before provisioning in SPLYNX. The steps include accessing the OLT interface, assigning the ONU number and type, configuring the traffic and service port details, setting the service channel configuration for internet access, and saving and checking the configuration changes.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Step by Step For Zte Onu Config

    Uploaded by

    femi.jerry2
    119 views2 pages
    The document provides instructions for configuring a new ONU on an OLT, including checking for the available ONU slot on the appropriate PON, entering configuration mode and assigning details like the ONU number, serial number, bandwidth profile, VLAN tagging, and verifying the ONU power levels before provisioning in SPLYNX. The steps include accessing the OLT interface, assigning the ONU number and type, configuring the traffic and service port details, setting the service channel configuration for internet access, and saving and checking the configuration changes.

    Original Title

    Step by Step for Zte Onu Config

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides instructions for configuring a new ONU on an OLT, including checking for the available ONU slot on the appropriate PON, entering configuration mode and assigning details like the ONU number, serial number, bandwidth profile, VLAN tagging, and verifying the ONU power levels before provisioning in SPLYNX. The steps include accessing the OLT interface, assigning the ONU number and type, configuring the traffic and service port details, setting the service channel configuration for internet access, and saving and checking the configuration changes.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    119 views2 pages

    Step by Step For Zte Onu Config

    Uploaded by

    femi.jerry2
    The document provides instructions for configuring a new ONU on an OLT, including checking for the available ONU slot on the appropriate PON, entering configuration mode and assigning details like the ONU number, serial number, bandwidth profile, VLAN tagging, and verifying the ONU power levels before provisioning in SPLYNX. The steps include accessing the OLT interface, assigning the ONU number and type, configuring the traffic and service port details, setting the service channel configuration for internet access, and saving and checking the configuration changes.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    Login to the OLT

    Check if you can see the ONU on Unconfig

    a. CDV-PARADISE-ESTATE-OLT#show gpon onu uncfg

    If seen, check which of the PON e.g gpon 1/2/1

    Also, check the last ONU config on that PON

    E.g: 1/2/1 attached image below has the last ONU at 36, so if configuring a new one will start at

    37

    Now, get to your configure terminal ( Conf t command)

    1. CDV-PARADISE-ESTATE-OLT(config)#interface gpon-olt_1/2/1
    2. onu 37 type ZTE-F660 sn ZTEGC9118D5B
    exit the terminal
    3. CDV-PARADISE-ESTATE-OLT(config)#interface gpon-onu_1/2/1:37
    4. NAME AYOTUNDE OLABISI
    5. sn-bind enable sn
    6. tcont 1 name T1 profile T1-20M (please note this is for the bandwidth the customer is paying
    for, if it is 10mb, then use 10M)
    7. gemport 1 unicast tcont 1 dir both
    8. switchport mode hybrid vport 1
    9. service-port 1 vport 1 user-vlan 78 vlan 78
    exit the terminal

    Service Channel config

    10. CDV-PARADISE-ESTATE-OLT(config)#pon-onu-mng gpon-onu_1/2/1:37


    11. service HSI type internet gemport 1 cos 0 vlan 78
    12. vlan port eth_0/1 mode tag vlan 78 priority 0
    exit terminal to normal mode and then;

    CDV-PARADISE-ESTATE-OLT#write
    Backuping old configuration into flash...
    Collecting configuration into memory...
    Writing configuration into flash...[OK]

    Check the power if it is within threshold before proceeding to the SPLYNX.

    CDV-PARADISE-ESTATE-OLT#show pon power attenuation gpon-onu_1/2/1:37

    Thank You

    You might also like