DK INFUSETEK CO.

,LTD

Basic syringe pump

SPLab Series

SPLa
b01

SPLab01 SPLab02

SPLab04

Introduction
The syringe pump with infusion/withdrawl mode. Online flow rate modification function: the pump is running, without stopping, adjust the

flow rate at any time to meet complex application. stainless steel body, and large-screen chromatic LCD is easy to operate. It can install and

fix different types of injectors or syringes , and it is

Features

1.Colorful LCD display: Friendly interface, large-screen LCD display every technical parameter in real time.
2.Input injector inner diameter function: Can choose the injector from the list or input the injector inner diameter directly.
3.Two measurement mode for selection: Infusion volume --- lnfusion rate, Infusion volume --- Infusion time.
4.6 different working modes: Infusion, withdrawal, infusion/withdrawal, withdrawal/infusion, continuous and additional mode( infusion/
withdrawal, then exclude bubble).The parameters of each working mode saving separately.
5.Protection function:The pump will stall and give an alarm when the drive structure of the pump is blocked.
6.Online flow rate modification function: the pump is running, without stopping, adjust the flow rate at any time to meet complex application.

www.infusetek.com [email protected]
 DK INFUSETEK CO.,LTD

Technical Specifications

Flow Rate(μL/min-mL/min)
Plastic Syringe Inside Diameter(mm)
SPLab01/SPLab02 SPLab04-SPLab12
1mL 4.70 0.087~2.290 0.087~2.290
2.0mL 9.12 0.326~8.623 0.326~8.623
5mL 12.48 0.612~16.147 0.612~16.147
10mL 15.89 0.992~26.177 0.992~26.177
20mL 20.00 1.571~41.469 ⸻⸻
30mL 22.50 1.988~52.484 ⸻⸻
50mL 28.90 3.280~86.588 ⸻⸻
100mL 32.00 4.021-106.154 ⸻⸻

150mL 40.00 6.283-165.871 ⸻⸻

Flow Rate(μL/min-mL/min)
Glass Syringe Inside Diameter(mm)
SPLab01-G1/SPLab01-G2/SPLab02-G1
250μL 2.30 0.021-0.548
500μL 3.25 0.041-1.095
1mL 4.60 0.083-2.193
2.5mL 7.28 0.208-5.494
5mL 10.30 0.416-10.99
10mL 14.57 0.833-22.00
25mL 23.00 2.077-54.84
50mL 32.57 4.165-109.9
100mL 32.57 8.165-109.9

Flow Rate(μL/min-mL/min)
Microsyringe Inside Diameter(mm)
SPLab01/SPLab02
10μL 0.50 1-25.91
25μL 0.80 2.5-66.34
50μL 1.10 4.75-125.4
100μL 1.60 10-256.3

www.infusetek.com [email protected]
 DK INFUSETEK CO.,LTD

Technical Specifications

Infusion, withdrawal, infusion/withdrawal, withdrawal/infusion, continuous, additional mode

Working mode(Six)
(infusion/withdrawal, then exclude bubble)

Channel number 1 2 4 6 8 10 12
Syringe size 10μL-150mL 10μL-10mL
Syringe selection Syringe size and customized diameter

Linear speed range 5μm/min-132um/min(Flow rate=Linear speed* syringe inner cut area )

Min. linear rate 5μm/min

Linear force ≥16kgf

Max. stroke 140mm

Stoke resolution 0.078μm/μstep

Accuracy Error≤ ±0.5%, Stroke≥30% of maximum stroke

Display mode 320×240TFT-LCD
Control method Rotary encoded switch and imported membrane keypad
Power-off memory Display the previous data parameter after power supply again
External control Active switch signal: 5V
Communication interface RS485, Modbus protocol(RTU mode)
Power supply AC 220V±10%(standard), AC 110V±10%(option)
Condition temperature 0-40℃
Relative humidity <80%
IP rate IP31

Dimension(mm) 282*213*150 282*241*157 282*241*157 282*241*157 282*241*157 282*241*157

Weight 5.26kg 5.40kg 5.40kg 5.66kg 5.78kg 5.96kg 6.16kg

www.infusetek.com [email protected]
DK INFUSETEK CO.,LTD

Syringe Pump External Control Schematic

Dimension Drawing (Unit:mm)

www.infusetek.com [email protected]