Bitcoin Donations:

CHIMERA .410 V1.3

Hybrid 3D Printed / Metal Framed Break Barrel Shotgun

bc1q7s3phq3gf30tw7
gem5rtxzcyj2ejgmehv
rzv3q

Videos:

https://www.youtube.
com/user/pilotgeek
 Chimera 410 – Single Shot Break
Barrel
1 DISCLAIMER
Please read and understand this manual fully before attempting assembly. This
product is not print-in-place. This design requires skilled machining and assembly of
additional components for complete assembly. You will need a rotary tool with cutoff
wheel at minimum. These plans are intended for educational purposes only and
assembly is at your own risk.

The Chimera is intended to shoot .410 shells, and has been tested only with them.
Alternate barrels may be possible at your own risk.

The Chimera is an experimental hobbyist project. It is not designed to be carried, and

it is not intended for self-defense. The current design does not feature proper modern
safeties and should be used in a controlled environment with careful handling.

These plans are provided as-is. They should be treated as a novelty, and nothing more.
These files are not an actual gun, they are CAD files depicting design of a handgun.
They require skill and knowledge to make into a functional object. You are responsible
for knowing the laws regarding firearms where you live. Before building, please read
up on all applicable gun laws and decide for yourself whether or not you can legally
build this where you live.

Read all instructions carefully. Do not skip or

skim. It’s all here for a reason.
2 PARTS INDEX - REQUIRED PARTS
Amazon links are paid / sponsored links. Links may change or disappear
depending on sellers and availability, please check what you buy matches
description listed in this manual!

2.1 TUBING
• Foregrip: 1" 16ga steel tubing x 312mm
• Receiver / Buttstock: 1” 16ga steel tubing x 400mm
• Break Latch / Hinge: ¾” 16ga steel tubing x 112mm
• Barrel: ¾” x .156” DOM tubing – Between 19 and 22” for good balance.

2.2 SCREWS & HARDWARE

• ¼” Steel Rod
• M4 Set Screws / Grub Screws - https://amzn.to/3uLCI4r
• Frame Screws: 34x M5x16mm - https://amzn.to/3rMPIrF
• Barrel Pinch Bolts: 4x M5x40mm - https://amzn.to/31HsrN9
• 3mm Steel Rods - https://amzn.to/3oBKgpt
• Striker & Latch Spring: 0.8mm x 6mm x 50mm Stainless Steel Compression Spring

2.3 EVERYTHING ELSE

• JB Weld / Epoxy (Don’t use Quick Setting) - https://amzn.to/37vCumZ
• Plastic Safe Grease - https://amzn.to/2F3pUxO
3 3D PRINTING
I tested everything in PLA. I recommend the trigger and receiver parts to be
100% to prevent deformation under stress / compression. Everything else can
probably get away with 20-30% and thick walls.

3.1 GENERAL SETTINGS

• Nozzle: 0.4mm
• Slicer: Confirmed to print on Cura 4.5
• Print in the default orientations. Print each part separately for best results.

3.2 PRINT SETTINGS

• Infill
Break Latch Parts, Receiver Parts, and Striker/Trigger Parts must be 100%
o
Infill.
o Barrel blocks should be printed at high infill or walls, use your judgement.
o Grips, Buttstock, and Inner Blocks may be around 20-25% infill.
• Supports
o Only the Outer Receiver requires supports.
o Print 100% infill parts / important parts with brim or raft. This was the
easiest way I found to prevent the frame from warping. A heated build
plate is required. I recommend an enclosure.
• Notes
o Don't try to print too fast, you want it to be good. Even when using PLA, it
helps to build in a warmer environment for strong layer adhesion and less
warping.
o Low quality prints may require sanding. Polish any mating surfaces or
moving parts.
o If available, use plastic-safe grease on all moving parts. It will ease trigger
pull & wear.
4 METAL FABRICATION
Using the 3D printed templates, drill pilot holes with a 1/16" bit, then finish with
size listed on template.

Template areas with a dottel line indicate channels to be cut. Drill each hole to
size listed, then cut the tangent between the outer radius of each hole using a
dremel or similar tool.

Larger hollow areas such as 3B will also need to be cut with a dremel / rotary
tool, or hacksaw.

4.1 FOREGRIP
The foregrip uses 1” square tubing, cut to 312mm in length.
Drill and cut using templates as shown, noting drill sizes
listed on template.

4.2 HINGE / LATCH

The middle hinge section uses ¾” square tubing cut to
112mm. Drill and cut using templates as shown, noting
drill sizes listed on template. The tubing also needs to be
cut to match the profile of the template.

4.3 RECEIVER
Cut a 400mm length of tubing, leaving an
additional 25mm tab on one side. Bend the
remaining tab downwards to act as the
breech face. If you have the ability, use a
welder to box this in, which will greatly
improve strength.

Drill and cut using templates as shown,

noting drill sizes listed on template. The
firing pin hole should be around 7/64”

BE PRECISE WITH ALL CUTS! THE LOCKING

MECHANISM RELIES ON PRECISE CUTS IN
THE CHANNELS FOR PROPER OPERATION.
4.4 BARREL
Cut ¾” x .156” DOM tubing to desired
barrel length. Use a chamber reamer
(recommended method) or a 15/32” drill
bit using the DrillGuide.stl part. If you
don’t want to drill a chamber, the parts could be modified or adapted to fit a properly
chambered .410 barrel blank.

4.5 FIRING PIN & GUIDE RODS

Cut 3mm rod cut to around 63mm in length,
with the tip reduced to a smaller
2mm wide rounded end. This can
be done by chucking the rod into
a drill and using a file while
spinning.

Secure the firing pin into the striker

with M3 grub screw / set screw.

Cut 3mm rod to around 60mm for

the charging handle, and another
to 40mm for the striker spring guide rod. Epoxy the
40mm guide rod into the spring retainer. Set aside
all parts for later assembly.

4.6 BREAK BARREL HINGE & LATCH

Cut a length of ¼” rod to 50mm in length, and
reserve for hinge assembly. Cut another length of ¼” rod to 62mm and reserve for
latch / lock assembly.
5 ASSEMBLY

5.1 FOREGRIP / BARREL BLOCKS

Install the inner barrel blocks into the
foregrip tubing. The holes should line up
with the holes drilled in the metal.
Numbers should be towards the
forward end of the gun and sit in
numerical order front to back.

Slide grips and barrel blocks onto the

tubing as shown. The outer-middle
barrel blocks are optional cosmetic
parts, and use short sections of M3 rod
to align with the other sections.

Use 14x M5 x 16mm screws to secure all parts

together.

5.2 HINGE / LATCH

Install 0.8mm x 6mm x 50mm spring
and plunger into the breaklatch
frame assembly, and ensure free
operation, sanding if necessary. Use
plastic-safe grease to ensure smooth
operation. Close the assembly with
the spacer, and insert into ¾” metal
tubing. If fit is too loose, you may
want to permanently fix this part into the
metal using epoxy.

While pushing the plunger back, insert the ¼”

x 62mm rod through the slot. Add knobs, and
secure with 4mm grub screws / set screws.
5.3 RECEIVER / STRIKER
Insert the printed inner receiver into the
metal tubing receiver. Ensure all screw
holes line up, and that metal and plastic
breech faces sit firmly against each other
with no gaps. I recommend using epoxy
on the face of the plastic "inner receiver"
to help eliminate gaps between the
metal breech face and the plastic.

Fish the striker, spring, and spring retainer through

the rear of the receiver. The trigger should slide
in from the slot on the underside. You’ll
secure these later, and yes it’s a pain in the
ass, you’ll probably need to use a long
screwdriver to hold it all together.

Slide the inner receiver assembly into the

outer receiver / pistol grip, and secure with
M5 x 16mm screws. Slide the 60mm rod
through the striker and glue the charging handle knobs on.
Insert the break barrel latch / hinge assembly
into the receiver, and secure with M5 x 16mm
screws. If the fit is too loose, you may want to
epoxy this section together to eliminate play in
the hinge, making sure not to get any epoxy into
the sliding latch.

Insert the inner and outer buttstock at the rear,

and secure with M5 x 16mm screws. Install the
handgrip plug through the rear of the receiver
and attach the handgrips with M3 screws.
5.4 FINALIZATION
Pin the hinge together using an M5 x 50mm partially threaded bolt (Old Revision) or
50mm length of ¼” rod, and secure with M4 grub / set screws from bottom (New
Revision).

Ensure there is no play in the closed mechanism.

Slide the barrel into place and use an empty 410
shell to adjust headspacing. There should be no
space between the rear of the cartridge and
the breech face. Once the barrel position is
adjusted for proper headspacing, use M5 x
40mm bolts to clamp the barrel in place, and
use M4 set screws for additional clamping force
to ensure it does not shift forward.
6 SAFETY & USAGE

6.1 TESTING

TEST FIRE THE GUN REMOTELY. Secure the gun to a solid

surface and fire remotely with a string attached to the
trigger.
Inspect the condition of the gun during and after each session of usage. Discard any
parts which show excessive wear. Always wear safety glasses and ear projection when
firing. You do not want ear or eye damage from vented gases in the case of cartridge
failures.

6.2 LOADING & EJECTION

The Chimera was designed for 2.5” 410
cartridges. There is no automatic ejection, you
will have to manually pull spent cartridges from
the chamber. A properly reamed and polished
chamber should allow spent cases to be easily
removed. If cases stick, try using a proper
chamber reamer, or use a hone to polish the
chamber and remove any dips, burrs, or
imperfections.

7 LEGALITY
The Chimera is a CAD representation depicting theoretical design of a shotgun. These
plans are provided as-is for entertainment and educational purposes only. I am not
liable for any injury or damage resulting from using these files. These plans do not
represent a complete functional 3D Printed gun, but a frame and components which
require additional tools, materials, and knowledge to make into a functional object.
You are responsible for knowing the laws regarding firearms where you live. Before
building, please read up on all applicable gun laws and decide for yourself whether or
not you can legally build this where you live.