0% found this document useful (0 votes)
39 views

B-82 Module Initialization

This document provides a quick chart and overview of module initialization tasks that must be performed when replacing modules for various Mazda vehicle models. It lists 6 initialization tasks including configuration, immobilizer registration, initialization/calibration/learning, module/data reset, advanced key programming, and steering lock unit initialization. Various vehicle modules are then listed with numbers indicating which initialization tasks are required when replacing those modules. Refer to workshop manuals for full repair procedures.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
39 views

B-82 Module Initialization

This document provides a quick chart and overview of module initialization tasks that must be performed when replacing modules for various Mazda vehicle models. It lists 6 initialization tasks including configuration, immobilizer registration, initialization/calibration/learning, module/data reset, advanced key programming, and steering lock unit initialization. Various vehicle modules are then listed with numbers indicating which initialization tasks are required when replacing those modules. Refer to workshop manuals for full repair procedures.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

USA spec.

- Modules Requiring Inititalization (M-MDS Software : IDS 82 )


Caution: This file is a quick chart of module initialization using M-MDS when they replaced subject modules. Please refer to workshop manual for the full repair procedures.

* The term "Initialization" encompasses the tasks shown on the table below, which are performed during module replacement.
Initialization Tasks Description
Configuration (hereinafter "Config"), the action of setting the constants in the software, is performed to ensure that the operating environment of the
1 Configuration module is compatible with vehicle specifications.
Modules will not function properly when replaced if they are not configured.
The Immobilizer System (hereinafter "Immobi") is a vehicle theft prevention system.
Immobilizer Registration (PATS Registration) The vehicle's engine will not start properly if the Immobi's settings are not reconfigured (key registration and/or parameter reset) when related modules and
2
(Only for immobi-equipped vehicles) keys are replaced. When you work , you need to search Incode through immobilizer Incode Searchin

3 Initialization / Calibration / Learning An electrically-controlled system will not function properly if this is not performed.

4 Module Reset / Data Reset The module will not function properly if it is not reset.
Program Advanced Key
5 The vehicle's engine will not start using advanced key if the settings are not reconfigured when related modules and keys are replaced.
(Only for advanced keyless system equipped)
Steering Lock Unit Initialization
6 The vehicle's engine will not start if the initialization is not performed when steering lock unit is replaced.
(Only for advanced keyless system equipped)
8 ABS Air Bleed Fill H/U with brake fluid and remove air from it.

* Models Requiring Initialization / Module List


Numbers on the table refer to items described above.
Hyphens "-" indicate items that do not require initialization. For module manes, refer to the Module Name List portion of this document.
For module names, refer to the list shown below.

(Auto Leveling Sensor)


(Seat Weight Sensor)

GEM/ BCM/ FBCM/


(Steering Lock Unit)

(Rain Light Sensor)


GEM/ PJB/ LCM
HCM/ HID/ AFS

RKE/SKE/SSU

EPS/ EHPAS
DSC/ RSC
HEC/ IC

RBCM

TPMS

SCBS

EATC
4x4M

(Tire)
RCM
PCM

TCM

BSM

RAP
FSC
ABS

MID
AM
(included
Mazda2(DE) 1, 2 - - 1 3 1, 2 - 3 - - 6 - 1 - 1, 3 - - - - - - - -
in HEC)
Mazda3 (BK) (-MY06) 1*B, 2 - - 1 3 1, 2 1*C 1*C, 3 - - - 1, 4 - - 1 1 - - - - - - - -
Mazda3 (BK) (MY07-) 1*B, 2 - - 1 3 1*G, 2 1*C 1*C, 3 - - - 1, 4 - - 1 1*G - - - - - - - -
Mazda3 (BK) (MY07-) 1*E, 2,
1*B, 2 - - 1 3 1*G 1*C 1*C, 3 - 6 1, 4 - - 1 1*G - - - - - - - -
(w/ Advanced Keyless) 5, 6
(included
Mazda3 (BL) (MY10-) 1, 2 - - 1 3 1, 2 1*K 1*K, 3 3*D - - - 1 - 1 1*L - 1 - - - - -
in HEC)
Mazda3(BL) (MY10-) 1*E, 2, (included
1, 2 - - 1 3 1 1*K 1*K, 3 3*D 6 - 1 - 1 1*L - 1 - - - - -
(w/ Advanced Keyless) 5, 6 in HEC)
3 -
(6AT (included
Mazda3 (BL) (MY12-) 1, 2 1 3 1, 2 1*K 1*K, 3 3*D - - - 1 - 1 1*L - 1 - - - - -
only) in HEC)

3 -
Mazda3(BL) (MY12-) (6AT 1*E, 2, (included
1, 2 1 3 1 1*K 1*K, 3 3*D 6 - 1 - 1 1*L - 1 - - - - -
(w/ Advanced Keyless) only) 5, 6 in HEC)

1*E, 2, 1
Mazda5 (CR) 1*B, 2 - - 1 3 1, 2 1*C 1*C, 3 3*D 6 - - 3*D 1 - - - - - - - -
5, 6 (*G: MY08-)
Mazda6 (-04MY) 1, 2 - - - - 1 1 1, 3 - - - - - - - - - - - - - - - -
Mazda6 (05MY-) 1, 2 3*H - - 3 1 1 1, 3 - - - - - - - 1(MY08 -) - - - - - - - -
1*E, 2,
Mazda6 MPS (GG) 1, 2 - - 1 3 1 1 1, 3 - 6 - - - - - - - - - - - - -
5, 6
3 -
(included
Mazda6 (GH) 1, 2 (6AT 1 3 1, 2 1 1 - - - - - 3*D - - - - 3 - - - -
in HEC)
only)
3 -
Mazda6 (GH) (6AT 1*E, 2, (included
1, 2 1 3 1 1 1 - 6 - - 3*D - - - - 3 - - - -
(w/ Advanced Keyless) only) 5, 6 in HEC)
1(MY05- and 1 3 1 1
MPV (LW) - - - - - - - - - - - - - - - - - - -
3.0L) *F (04MY-) (04MY-) (04MY-) (04MY-)
1*E, 2, (included
Mazda MX5 Miata (NC) 1, 2 - - 1 3 1, 2 1 1, 3 - 6 - - - - - - - - - - - -
5, 6 in HEC)
RX-8 (FE) 1, 2 - - 1 - 1 - 1, 3 - 1*E, 2 - - - - 3 1 - - - - - - - -
RX-8 (FE) 1*E, 2,
1, 2 - - 1 3 1 - 1, 3 - 6 - - - 3 1 - - - - - - - -
(w/ Advanced Keyless) 5, 6
RX-8 (FE) (09MY-) 1, 2 - - 1 - 1 - 1, 3 - 1*E, 2 - - - - 3 1 1*J - - - - - - -
RX-8 (FE) (09MY-) 1*E, 2,
1, 2 - - 1 3 1 - 1, 3 - 6 - - - 3 1 1*J - - - - - - -
(w/ Advanced Keyless) 5, 6
Tribute (-02MY) 1, 2 - - - - 1 - - - - - 1 - - - - - - - - - - - -
Tribute (03MY-) 1, 2 - - - - 1 - - - - - 1 - - - - - - - - - - - -
1*K,
CX-5 (KE) 1, 2 1, 3 1 1 3 1 - 1*K、3 1, 2 - - 1 - 1*K - - - - 3 1, 3 1*K 1*K -
3*D
(included
CX-7 (ER) 1, 2 1, 3 - 1 3 1, 2 - 3 - - - - - - - - 1 - - - - - -
in HEC)
CX-7 (ER) 1*E, 2, (included
1, 2 3 - 1 3 1 - 3 - 6 - - - - - 1 - - - - - -
(w/ Advanced Keyless) 5, 6 in HEC)
3
(included
CX-7 (ER) (10MY-) 1, 2 (6AT - 1 3 1, 2 - 3 - - - 1 - - - - 1 1 3 - - - -
in HEC)
only)
3
CX-7 (ER) (10MY-) 1*E, 2, (included
1, 2 (6AT - 1 3 1 - 3 - 6 1 - - - - 1 1 3 - - - -
(w/ Advanced Keyless) 5, 6 in HEC)
only)
(included 3
CX-9 (TB) 1, 2 3 - 1 3 1, 2 - 3, 8 - - - 1 - 3*D - - 1 - 1, 3 - - -
in HEC) (MY08 -)
CX-9 (TB) 1*E, 2, (included 3
1, 2 3 - 1 3 1 - 3, 8 - 6 1 - 3*D - - 1 - 1, 3 - - -
(w/ Advanced Keyless) 5, 6 in HEC) (MY08 -)
*A : Setting immobi is required without Diagnostic Tester. (Refer to Workshop Manual)
*B : Body Type configuration is required for DSC equipped vehicles. (Programmable Parameters > TireSize / Axle Ratio)

*C : Configuration data is VIN data only. (When As-Built data is required, you will be able to complete the procedure by entering VIN only. You do not need to obtain the As-Built data sheet.)

*D : You can do the same operation without Diagnostic Tester. (Refer to Workshop Manual)

*E : Keyless Control Unit configuration is required for Advanced Keyless equipped vehicle. Regarding RX-8, configuration is required for not only Advanced Keyless but also Immobilizer equipped vehicle.

*F : This operation is required for the applicable vehicles or modules only. (This functionality is available on the face-lifted models or models with module design changes.) Refer to workshop manual.

*G : Meter set has both Meter ECU and TPMS ECU. If the meter set is replaced, IC/HEC and TPMS configuration procedures are required.
*H : 3.0L only.
*J : When you change tire size (ex. you change wheel for 18 inch), you need to write tire size to PCM (change configuration data of PCM).
*K : Configuration using M-MDS is not required, however you need to set IG ON and keep it for specified time (see workshop manual). This procedure allows the module to install/refer configuration data from HEC/IC.
*L : When you change tire size (ex. you change wheel for 18 inch), you need to write tire size to PCM and HEC/IC (change configuration data of PCM and HEC/IC).
* Module Name List
Module Name Module Numbers
Workshop Manual Name Function
(M-MDS Name) on the As-built Sheet
PCM1 - PCM9
PCM Powertrain Control Module Controls the engine.
7E0-0*-01 (*A)
TCM Transmission Control Unit Controls transmission functions. -
Sensors detect the degree of impact and transmit a signal,
RCM SAS Control Module 58 or 737
deploying (opening) the air bag.
HEC (IC) Instrument Cluster Controls the meters. 60 or 720
Controls brake fluid pressure to prevent the wheels from locking
ABS (ABS/TCS) Antilock Brake System 28 or 760
when the brakes are applied.
Controls brakes and engine output in order to prevent the vehicle
DSC (ABS/TCS/DSC) Dynamic Stability Control 28 or 760
from spinning and drifting laterally while moving.
SCBS Smart City Brake Support Operates the automatic brakes to reduce collision impact. 793
Controls brakes and engine output in order to prevent the vehicle
RSC (ABS/TCS/DSC) Roll Stability Control 28 or 760
from spinning, drifting and rolling while moving.
Controls the electronic components of the body, such as the door
GEM Generic Electronic Module 52
locks and the keyless entry system.
BCM (GEM) Body Control Module Controls the body's electronic components. 726
FBCM Front Body Control Module Controls the body's electronic components. 726
RBCM Rear Body Control Module Controls the body's electronic components. 7B7
Controls the body's electronic components. (Contains fuses and
PJB (GEM) Passenger Junction Box 726
relays.)
LCM Auto Light/Wiper Control Module Controls the headlamp and wiper. 70
Controls door lock and keyless entry systems; issues engine start
RKE/SKE Keyless Control Module 731
permission.
Controls door lock and keyless entry systems; issues engine start
SSU Start Stop Unit 731
permission.
EPS Electric Power Steering Electronically controls steering assistance. 730
EHPAS (EPS) Electro Hydraulic Power Assist Steering Electronically controls hydraulic (oil pressure) steering assistance. 730
Monitors the tire status and alerts the driver with the warning light
TPMS (TPM) Tire Pressure Monitoring System 751
and buzzer if there is a problem.
AM Audio Amplifier Controls the audio. 7A4
MID Multi Information Display Show various information. 773
BSM Blind Spot Monitoring Controls Blind Spot Monitoring system. 7C6
Controls the high beam control (HBC) system and lane departure
FSC Forward Sensing Camera 706
warning system (LDWS).
EATC Electronic Air Temparature Controller Controls air temparature condition. 733
RAP Remote Anti-Theft / Personality Module -
*A : If we use IDS/PDS 45 or older, “VIN”, “Vehicle Data” and “PCM 1 through 13” (for non-applicable models, PCM 1 through 9) of the As-Built data must be entered during PCM configuration.
However, if we use IDS/PDS 46 or newer, 7E0-01-01 through 7E0-04-01 must be entered instead of PCM 10 through 13. (Ref. Tool Equipment T046/06)

* Additional Notes
1) Check service codes after completing configuration!
2) M-MDS will require As-Built data in the following circumstances:
M-MDS makes decisions automatically and reports the results to service engineers.
(1) When configuration data cannot be retrieved from the old module. (including cases in which the old module was lost.)
(2) If one of the following service codes was configured on the module: P0602, P0601, or B2477.

You might also like