Total Station Setup and

Operation
Sokkia SET Total Station

Downloaded from www.Manualslib.com manuals search engine

 Parts of the SET Total Station

Downloaded from www.Manualslib.com manuals search engine

 Parts of the SET Total Station

Downloaded from www.Manualslib.com manuals search engine

 Sokkia SET 550 Total Station
Keys/Screen

Downloaded from www.Manualslib.com manuals search engine

 SET 550
Menu Pages

Downloaded from www.Manualslib.com manuals search engine

 SET 550
Menu
Pages

Downloaded from www.Manualslib.com manuals search engine

 Leveling the Total Station
„ Leveling the Total Station must be
accomplished to sufficient accuracy otherwise
the instrument will not report results
„ Leveling the instrument takes 30 to 45 minutes
– make sure you can see all targets from the
instrument station before going through the
process

Downloaded from www.Manualslib.com manuals search engine

 Step 1: Tripod Setup
„ Tripod legs
should be
equally spaced
„ Tripod head
should be
approximately
level
„ Head should
be directly
over survey
point

Downloaded from www.Manualslib.com manuals search engine

 Step 2: Mount Instrument on Tripod
„ Place Instrument
on Tripod
„ Secure with
centering screw
while bracing the
instrument with
the other hand
„ Insert battery in
instrument before
leveling

Downloaded from www.Manualslib.com manuals search engine

 Step 3: Focus on Survey Point
„ Focus the optical
plummet on the
survey point

Downloaded from www.Manualslib.com manuals search engine

 Step 4: Leveling the Instrument
„ Adjust the leveling foot screws to center the
survey point in the optical plummet reticle
„ Center the bubble in the circular level by
adjusting the tripod legs

Downloaded from www.Manualslib.com manuals search engine

 Step 4: Leveling …
„ Loosen the horizontal clamp and turn instrument until
plate level is parallel to 2 of the leveling foot screws
„ Center the bubble using the leveling screws- the
bubble moves toward the screw that is turned
clockwise
„ Rotate the instrument 90 degrees and level using the
3rd leveling screw

Downloaded from www.Manualslib.com manuals search engine

 Step 4: Leveling …
„ Observe the survey point in the optical
plummet and center the point by loosening the
centering screw and sliding the entire
instrument
„ After re-tightening the centering screw check
to make sure the plate level bubble is level in
several directions

Downloaded from www.Manualslib.com manuals search engine

 Step 5: Electronically Verify
Leveling
„ Turn on the instrument by
pressing and holding the “on”
button (you should hear an
audible beep)
„ The opening screen will be the
“MEAS” screen. Select the
[Tilt] function
„ Adjust the foot level screws to
exactly center the electronic
“bubble”
„ Rotate the instrument 90
degrees and repeat

Downloaded from www.Manualslib.com manuals search engine

 Step 5: Adjust Image & Reticle
Focus
„ Release the horizontal & vertical clamps
and point telescope to a featureless light
background
„ Adjust the reticle (i.e. cross-hair) focus
adjustment until reticle image is sharply
focused
„ Point telescope to target and adjust the
focus ring until target is focused
„ Move your head from side-to-side to test
for image shift (i.e. parallax). Repeat the
reticle focus step if parallax is significant
„ NOTE: When the instrument operator
changes the reticle focus may need to be
adjusted

Downloaded from www.Manualslib.com manuals search engine

 Measuring the Height of An Object
„ Level the instrument at a site where the target can be viewed through the
telescope and the mirror target can be setup directly below the target
„ After powering on the instrument select “REM” from “MEAS” > “Menu”
„ Ht = h1 + h2
„ h2 = S (sin θz1) (cot θz2 ) – S (cos θz1)
„ NOTE: Instrument height does not affect this calculation

Downloaded from www.Manualslib.com manuals search engine

 Measurement of Target Height
„ Set the Target Height from “MEAS” > “Menu” >
“Coordinate” > “Station Orientation” > “Station
Coordinate”
„ Set the target height to the measured height of the
mirror target. You do not have to fill out the other
fields for a REM measurement
„ Press “ESC” to return to the “MEAS” menu
„ Select the “MEAS” > “Menu” > “REM”, sight the
mirror target, press [OBS] to measure “S”, then
[STOP]
„ Sight the object above the target for height
measurement
„ Select [REM] and then [STOP]

Downloaded from www.Manualslib.com manuals search engine

 REM Screen Results
„ To re-shoot the
mirror target use the
[OBS] on the REM
screen

Downloaded from www.Manualslib.com manuals search engine

 Calibrating the Instrument
„ Calibration must be completed before coordinates can
be obtained
„ 3 possible calibrations:
„ Backsight by angle: must know instrument coordinates and
have a landmark/target at a known azimuth
„ Backsight by coordinate: must know instrument
coordinates and have mirror target set on a position of
known coordinates
„ Resection (triangulation): must have 3 or more mirror
targets established at known 3D coordinates

Downloaded from www.Manualslib.com manuals search engine

 3D Coordinates
„ Coordinates may be absolute or relative depending on
survey requirements
„ Surveying the area of a mining site would require
relative coordinates, therefore, the initial instrument
X,Y,Z coordinates may be 5000, 5000, 100
„ Surveys that have to match a downloaded aerial photo
from the USGS would have to match UTM NAD83
coordinates so the starting point would have to be
determined by an accurate GPS receiver

Downloaded from www.Manualslib.com manuals search engine

 Calibrate by Backsight by Angle
„ Remember that when the instrument is
powered on it has a random X,Y coordinate
system: you must align the instrument with
your working coordinate system.
„ Level the instrument on the desired starting
survey marker. Make sure that on the last
leveling step the optical plummet is centered
on the survey point

Downloaded from www.Manualslib.com manuals search engine

 Backsight by Angle continued..
„ Measure the target height and
instrument height
„ Select [COORD] from the MEAS menu
„ Select “Stn. Orientation” and then “Stn.
Coordinate”
„ Edit the “N0”, “E0”, and “Z0” fields to
appropriate values (i.e. northing,
easting, elevation of instrument)
„ Enter the instrument and target height if
necessary
„ Select [OK] when done

Downloaded from www.Manualslib.com manuals search engine

 Backsight by Angle continued…
„ Select “Backsight” and then
“Angle” from the menu
„ Sight the landmark/target of known
azimuth relative to instrument with
telescope
„ Select “Angle” from menu. Note
that the menu displays the zenith
angle (ZA) and current horizontal
angle (HAR) and is waiting for you
to enter the known angle with
[EDIT]
„ Note: if you enter an azimuth angle
as “85.4514” this will be interpreted
as 85 degrees, 45 minutes, 14
seconds
„ IMPORTANT! You must select
[OK] to accept the angle. Never use
<Esc> to leave this screen!

Downloaded from www.Manualslib.com manuals search engine

 Backsight by Angle Continued…
„ NOTE: because the backsight by angle simply
sets the instrument horizontal angle encoder to
match your desired coordinate system the
mirror target is never “shot” by the beam. If
you can accurately sight on an object or
landmark such as a building corner the mirror
target is not needed. Make sure the instrument
is “locked” and accurately sighted with
telescope before entering the backsight angle.

Downloaded from www.Manualslib.com manuals search engine

 Backsight by Angle cont…
„ Because there is no internal statistical measure
of how well the backsight angle has been set it
is imperative to check the backsight
independently:
„ Known point: shoot the target at a position of
known X,Y,Z such as a GPS point. The result
should be within the resolution of the GPS.
„ Known angle: shoot to a landmark at a known
azimuth from the instrument location- the angle
should be within the resolution of the instrument

Downloaded from www.Manualslib.com manuals search engine

 Backsight by Coordinate
„ Use this method when you have 2
known survey points with the
instrument established on one and the
mirror target on the other survey point
„ From the “MEAS” menu select
[COORD] and then “Stn.
Orientation”. Set the instrument
coordinates with “Stn. Coordinate”
and then select [OK] and return to
“Backsight”
„ Select “Coord” and then enter the
backsight target coordinates (NBS,
EBS, ZBS) and select [OK]
„ Sight in the target and inspect the
“Azmth” (it should be reasonable for
your coordinate system).
„ Select [YES] to calibrate. If you don’t
select [YES] the coordinate system is
still random

Downloaded from www.Manualslib.com manuals search engine

 Backsight by coordinate …
„ Always check the calibration of the instrument
by shooting the target used for the backsight.
„ The resulting X,Y,Z should be within the
several cm resolution typical for a TS
instrument.
„ It is a very good idea to shoot other
benchmarks within range to make sure
accuracy is within acceptable limits

Downloaded from www.Manualslib.com manuals search engine

 Resection
„ Resection uses 3 or more
known target survey points
to automatically determine
the X,Y,Z coordinates of the
instrument
„ This has the significant
advantage of not requiring
the instrument to be leveled
exactly on a survey point-
any convenient location
where you can sight the
targets is OK
„ The ideal geometry is
displayed to the right

Downloaded from www.Manualslib.com manuals search engine

 Resection continued…
„ Prior to resection enter survey markers as known
points through the “MEM” menu
„ From the “MEAS” menu select “[MENU]” >
[RESEC]
„ The resection procedure requires that the known
coordinates be defined first, and in the order that
they will be shot
„ In the top right screen the 1st point has been
defined and the 2nd point is being entered. You
can use [READ] to read in previously entered or
measured points
„ Press the “>” or “<“ arrow to move to next or
previous point
„ When all points are entered select [MEAS]

Downloaded from www.Manualslib.com manuals search engine

 Resection continued…
„ The [MEAS] screen (right)
displays the point being shot – in
this example the 1st point
„ Choose [DIST] if you are
shooting to a mirror target,
[ANGLE] if not
„ Select [YES] to accept
measurement, [NO] to re-shoot,
[EDIT] to change target height
„ The [CALC] option will be
displayed when the standard
deviation of northing and easting
can be displayed

Downloaded from www.Manualslib.com manuals search engine

 Resection continued…
„ Press [CALC] or [YES] on last point to
display the calculated instrument
coordinates and the standard deviation of
easting (σE) and northing (σN). Press
[OK] to finish Resection, and then
[YES] to set the backsight
azimuth to the 1st shot point
„ Press [RESULT] to display the residuals of
each shot point- large deviations identify
“bad” points
„ If there are no problems press {Esc} to
return to main resection screen
„ The standard deviations are a measure of
the accuracy. They should be in the range of
several cm’s for most surveys

Downloaded from www.Manualslib.com manuals search engine

 Resection Notes
„ Resection initializes the X,Y,Z coordinates of the
instrument. Save this as a point (ex. G1S02 for group
2, instrument station #2) since it represents a
surveyed coordinate
„ Once the instrument is calibrated the mirror targets
can be taken down and used elsewhere
„ The instrument height should be entered before
resection is calculated
„ You can only begin shooting resection point 1 from
the resection point #3 or higher coordinate entry
screen

Downloaded from www.Manualslib.com manuals search engine

 Resection Notes
„ Certain
Geometries
should be
avoided…

Downloaded from www.Manualslib.com manuals search engine