WF Ae390

Technical data sheet
Version 2.0 09042022
WF-AE390
Anchoring epoxy adhesive
DESCRIPTION
Wolfix WF-AE390 anchoring epoxy adhesive is a two-component, non sag,
100% solids, multi-purpose, high-performance, moisture tolerant epoxy
adhesive designed for anchoring bolts and rebar steel into concrete and for
bonding or repairing a variety of household and common building materials
including concrete, porous tile, and stone.
USES
▪ Planting steel bars and bolts in concrete, stone or other substrate.
▪ Curtain wall & stone dry hanging brackets’ strengthening
▪ Building structure reinforcement & framework anchoring
▪ Various equipment's basic fixation
▪ Steel structures and concrete structures anchoring connection
▪ Rail fixing for railway building
GENERAL FEATURES
▪ High-strength
▪ Resists chemicals and solvents
▪ Moisture tolerant
▪ Fits standard caulking gun
▪ Non-shrink
▪ Fast-setting
 Initial set time of in as little as 15-30 min.
 Initial cure time of 2 hr.
 Final cure of 1-3days
▪ Non-sag
▪ Excellent adhesion
PRODUCT INFORMATION
Package: 390ml/pc, 20pc or 30pc per carton
Shelf life 18 months
Storage condition Stored in their original packaging, in
cool conditions (5℃-35℃) and out
of direct sunlight.
Version 2.0 09042022
WF-AE390
Color: Red and grey
Mix Ratio 3:1
Density 1.5g/cm3
Solids 100%
TECHNICAL INFORMATION
Compressive strength
▪ 7 days at 25-32℃ 70.6MPa
Compressive modulus
▪ 7 days at 25-32℃ 2400MPa
Tensile strength
▪ 7 days at 25-32℃ 42MPa
Elongation at break
▪ 7 days at 25-32℃ 1.6%
Bonding strength
▪ 7 days at 25-32℃ ≥11.4MPa
Heat deflection temperature
▪ 7 days at 25-32℃ 68℃
Absorption
▪ 7 days at 25-32℃ 0.18%
Linear Coefficient of Shrinkage on Cure
▪ 7 days at 25-32℃ 0.009
OPERABLE TIME AND CURING TIME
Ambient temperature (℃) -10-0 0-10 10-20 20-30 ≥35
Operable time (min) 60 45 30 20 15
Curing time 70% (h) 72 48 24 12 6
Full curing time (days) 20 14 12 7 3

Version 2.0 09042022
WF-AE390
APPLICATION INSTRUCTIONS
Installation information
Installation data- threaded rod
Installation data- Internal threaded sleeve
Installation data- Reinforcement bar

Version 2.0 09042022
WF-AE390
Installation process
1. Using the proper core bit size, drill a hole into the base material to the
required depth.
2. Rinse the hole until water runs clear.
3. Brush the hole with the proper wire brush - 2 times minimum.
4. Rinse the hole until water runs clear.
5. Blow the hole clean using a hand pump (suitable for maximum 20mm dia.
hole) or compressed air - 2 times minimum.
6. Brush the hole with the proper wire brush - 2 times minimum.
7. Blow the hole clean using a hand pump (suitable for maximum 20mm dia.
hole) or compressed air - 2 times minimum
8. Squeeze out separately and discard a minimum of 10cm until the mortar is
uniformly mixed and shows consistent color. Starting from the rear of the hole,
fill the hole up to approximately 2/3 with uniformly mixed adhesive.
9. Push the threaded rod / rebar into the hole while turning slightly to ensure
positive distribution
of the adhesive. Be sure that the rod / rebar is seated at the bottom of the
hole and that some
adhesive has flowed from the top of the hole.
10. Allow the adhesive to cure for the time specified for the actual concrete
temperature (in dry concrete). Do not disturb or load the anchor until the
adhesive has fully cured. Follow the longer curing time for wet concrete.
Version 2.0 09042022
WF-AE390
Application tools
Manually dispenser gun.
Electric dispenser gun
Steel brush used for cleaning the hole
Blow pump used for cleaning the hole
POINTS FOR ATTENTION

▪ Use up within the applicable period, do not use the adhesive if it is beyond
the applicable period;
▪ If the cartridges adhesive are not used up, they should be covered and sealed.
They should not be exposed to air for a long time;
▪ The construction workers should take all necessary safety measures (such as
wearing masks, gloves, goggles, etc.), and maintain fire prevention measures
as well as keeping the site clean;
▪ If the adhesive accidentally got in touch the skin and cloths, acetone can be
used to wipe it at once, followed by a great deal of clear water;
▪ If accidentally swallowed or splashed into the eyes, please seek immediate
medical service.
Version 2.0 09042022
WF-AE390
ENVIRONMENT, HEALTH AND SAFETY

For further information and advice regarding transportation, handling, storage
and disposal of chemical products, user should refer to the actual Safety Data
Sheets containing physical, environmental, toxicological and other safety
related data. User must read the current actual Safety Data Sheets before
using any products.
Shanghai wolfix new materials Co.,Ltd

Room703, building 3#, Lane 101 west Youyi Road, shanghai, China
+86 150 0066 9292

WF Ae390

Uploaded by

Copyright:

Available Formats

WF Ae390

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

WF Ae390

Uploaded by

Copyright:

Available Formats

Technical data sheet

Version 2.0 09042022

OPERABLE TIME AND CURING TIME

Ambient temperature (℃) -10-0 0-10 10-20 20-30 ≥35

Operable time (min) 60 45 30 20 15

Curing time 70% (h) 72 48 24 12 6

Full curing time (days) 20 14 12 7 3

Installation data- threaded rod

Installation data- Internal threaded sleeve

Installation data- Reinforcement bar

Manually dispenser gun.

Electric dispenser gun

Steel brush used for cleaning the hole

Blow pump used for cleaning the hole

POINTS FOR ATTENTION

ENVIRONMENT, HEALTH AND SAFETY

Shanghai wolfix new materials Co.,Ltd

You might also like