Lab 7 - Configuring and Verifying Extended ACLs

Lab 7 – Configuring and Verifying Extended ACLs
Topology
© 2015 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 6
Lab – Configuring and Verifying Extended ACLs
Addressing Table
Device Interface IP Address Subnet Mask Default Gateway
R1 G0/1 192.168.10.1 255.255.255.0 N/A

Lo0 192.168.20.1 255.255.255.0 N/A
S0/0/0 (DCE) 10.1.1.1 255.255.255.252 N/A
ISP S0/0/0 10.1.1.2 255.255.255.252 N/A
S0/0/1 (DCE) 10.2.2.2 255.255.255.252 N/A
Lo0 209.165.200.225 255.255.255.224 N/A
Lo1 209.165.201.1 255.255.255.224 N/A
R3 G0/1 192.168.30.1 255.255.255.0 N/A
Lo0 192.168.40.1 255.255.255.0 N/A
S0/0/1 10.2.2.1 255.255.255.252 N/A
S1 VLAN 1 192.168.10.11 255.255.255.0 192.168.10.1
S3 VLAN 1 192.168.30.11 255.255.255.0 192.168.30.1
PC-A NIC 192.168.10.3 255.255.255.0 192.168.10.1
PC-C NIC 192.168.30.3 255.255.255.0 192.168.30.1
Objectives
Part 1: Set Up the Topology and Initialize Devices
Part 2: Configure Devices and Verify Connectivity
 Configure basic settings on PCs, routers, and switches.
 Configure OSPF routing on R1, ISP, and R3.
Part 3: Configure and Verify Extended Numbered and Named ACLs
 Configure, apply, and verify a numbered extended ACL.
 Configure, apply, and verify a named extended ACL.
Part 4: Modify and Verify Extended ACLs
Background / Scenario
Extended access control lists (ACLs) are extremely powerful. They offer a much greater degree of control
than standard ACLs as to the types of traffic that can be filtered, as well as where the traffic originated and
where it is going.
In this lab, you will set up filtering rules for two offices represented by R1 and R3. Management has
established some access policies between the LANs located at R1 and R3, which you must implement. The
ISP router between R1 and R3 does not have any ACLs placed on it. You would not be allowed any
administrative access to an ISP router as you can only control and manage your own equipment.
Note: The routers used with CCNA hands-on labs are Cisco 1941 Integrated Services Routers (ISRs) with
Cisco IOS Release 15.2(4)M3 (universalk9 image). The switches used are Cisco Catalyst 2960s with Cisco
IOS Release 15.0(2) (lanbasek9 image). Other routers, switches, and Cisco IOS versions can be used.
Depending on the model and Cisco IOS version, the commands available and output produced might vary
from what is shown in the labs. Refer to the Router Interface Summary Table at the end of the lab for the
correct interface identifiers.
Note: Make sure that the routers and switches have been erased and have no startup configurations. If you
are unsure, contact your instructor.
Required Resources
 3 Routers (Cisco 1941 with Cisco IOS Release 15.2(4)M3 universal image or comparable)
 2 Switches (Cisco 2960 with Cisco IOS Release 15.0(2) lanbasek9 image or comparable)
 2 PCs (Windows 7, Vista, or XP with terminal emulation program, such as Tera Term)
 Console cables to configure the Cisco IOS devices via the console ports
 Ethernet and serial cables as shown in the topology
Part 1: Set Up the Topology and Initialize Devices

In Part 1, you will set up the network topology and clear any configurations if necessary.
Step 1: Cable the network as shown in the topology.
Step 2: Initialize and reload the routers and switches.
Part 2: Configure Devices and Verify Connectivity

In Part 2, you will configure basic settings on the routers, switches, and PCs. Refer to the Topology and
Addressing Table for device names and address information.
Step 1: Configure IP addresses on PC-A and PC-C.
Step 2: Configure basic settings on R1.

a. Disable DNS lookup.
b. Configure the device name as shown in the topology.
c. Create a loopback interface on R1.
d. Configure interface IP addresses as shown in the Topology and Addressing Table.
e. Configure a privileged EXEC mode password of class.
f. Assign a clock rate of 128000 to the S0/0/0 interface.
g. Assign cisco as the console and vty password and enable Telnet access. Configure logging
synchronous for both the console and vty lines.
Step 3: Configure basic settings on ISP.

a. Configure the device name as shown in the topology.
b. Create the loopback interfaces on ISP.
c. Configure interface IP addresses as shown in the Topology and Addressing Table.
d. Disable DNS lookup.
e. Assign class as the privileged EXEC mode password.
f. Assign a clock rate of 128000 to the S0/0/1 interface.

g. Assign cisco as the console and vty password and enable Telnet access. Configure logging
synchronous for both console and vty lines.
Step 4: Configure basic settings on R3.

a. Configure the device name as shown in the topology.
b. Create a loopback interface on R3.
c. Configure interface IP addresses as shown in the Topology and Addressing Table.
d. Disable DNS lookup.
e. Assign class as the privileged EXEC mode password.
f. Assign cisco as the console password and configure logging synchronous on the console line.
Step 5: (Optional) Configure basic settings on S1 and S3.

a. Configure the hostnames as shown in the topology.
b. Configure the management interface IP addresses as shown in the Topology and Addressing Table.
c. Disable DNS lookup.
d. Configure a privileged EXEC mode password of class.
e. Configure a default gateway address.
Step 6: Configure OSPF routing on R1, ISP, and R3.

a. Assign 1 as the OSPF process ID and advertise all networks on R1, ISP, and R3. The OSPF
configuration for R1 is included for reference.
R1(config)# router ospf 1
R1(config-router)# network 192.168.10.0 0.0.0.255 area 0
b. After configuring OSPF on R1, ISP, and R3, verify that all routers have complete routing tables listing all
networks. Troubleshoot if this is not the case.
Step 7: Verify connectivity between devices.

Note: It is very important to verify connectivity before you configure and apply ACLs! Ensure that your
network is properly functioning before you start to filter out traffic.
a. From PC-A, ping PC-C and the loopback and serial interfaces on R3.
Were your pings successful? ________
b. From R1, ping PC-C and the loopback and serial interface on R3.
c. From PC-C, ping PC-A and the loopback and serial interface on R1.
d. From R3, ping PC-A and the loopback and serial interface on R1.
e. From PC-A, ping the loopback interfaces on the ISP router.

f. From PC-C, ping the loopback interfaces on the ISP router.
Part 3: Configure and Verify Extended Numbered and Named ACLs

Extended ACLs can filter traffic in many different ways. Extended ACLs can filter on source IP addresses,
source ports, destination IP addresses, destination ports, as well as various protocols and services.
Security policies are as follows:
1. Allow user on 192.168.30.0/24 to access 192.168.10.0/24 network.
2. Allow user on 192.168.30.0/24 to ping 192.168.10.0/24 network.
3. Allow user on 192.168.30.0/24 to access 10.1.1.1 telnet service
That means 192.168.30.0/24 network cannot reach any other network except 192.168.10.0/24 and telnet to
10.1.1.1
??(config)# ip access-list extended LAB7

?? (config-ext-nacl)# permit tcp 192.168.30.0 0.0.0.255 192.168.10.0 0.0.0.255
?? (config-ext-nacl)# permit icmp 192.168.30.0 0.0.0.255 192.168.10.0 0.0.0.255
?? (config-ext-nacl)# permit tcp 192.168.30.0 0.0.0.255 host 10.1.1.1 eq 23
?? (config)# interface G0/1
Where should the extended ACL LAB7 be implemented?

____________________________________________________________________________________
To what interface should LAB7 be applied?
____________________________________________________________________________________
In what direction should LAB7 be applied?
____________________________________________________________________________________
a. Apply LAB 7 to the G0/1 interface.

R3(config)# interface g0/1
R3(config-if)# ip access-group LAB7 in
b. Verify ACL 100.
1) From PC-C ping R3 S0/0/1.Were you ping successful? Explain your results.
________________________________________________________________________________
2) From PC-C ping ISP S0/0/0.Were you ping successful? Explain your results.
________________________________________________________________________________
3) From PC-C ping PC-A.Were you ping successful? Explain your results.
________________________________________________________________________________
4) Telnet 10.1.1.1 form PC-C. Were you able to telnet and get connected? Explain your results.
________________________________________________________________________________
5) From privileged EXEC mode prompt on R3, issue the show access-list command.
Router#show access-list
Extended IP access list LAB7
10 permit tcp 192.168.30.0 0.0.0.255 192.168.10.0 0.0.0.255
20 permit tcp 192.168.30.0 0.0.0.255 host 10.1.1.1 eq telnet
30 permit icmp 192.168.30.0 0.0.0.255 192.168.10.0 0.0.0.255
Reflection
1. Why is careful planning and testing of ACLs required?
_______________________________________________________________________________________
_______________________________________________________________________________________
2. Which type of ACL is better: standard or extended?
_______________________________________________________________________________________
_______________________________________________________________________________________
_______________________________________________________________________________________
_______________________________________________________________________________________
3. Why are OSPF hello packets and routing updates not blocked by the implicit deny any access control entry
(ACE) or ACL statement of the ACLs applied to R1 and R3?
Router Interface Summary Table
Router Interface Summary
Router Model Ethernet Interface #1 Ethernet Interface #2 Serial Interface #1 Serial Interface #2
1800 Fast Ethernet 0/0 Fast Ethernet 0/1 Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)
(F0/0) (F0/1)
1900 Gigabit Ethernet 0/0 Gigabit Ethernet 0/1 Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)
(G0/0) (G0/1)
(F0/0) (F0/1)
(F0/0) (F0/1)
2900 Gigabit Ethernet 0/0 Gigabit Ethernet 0/1 Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)
(G0/0) (G0/1)
Note: To find out how the router is configured, look at the interfaces to identify the type of router and how many
interfaces the router has. There is no way to effectively list all the combinations of configurations for each router
class. This table includes identifiers for the possible combinations of Ethernet and Serial interfaces in the device.
The table does not include any other type of interface, even though a specific router may contain one. An
example of this might be an ISDN BRI interface. The string in parenthesis is the legal abbreviation that can be
used in Cisco IOS commands to represent the interface.

Lab 7 - Configuring and Verifying Extended ACLs

Uploaded by

Copyright:

Available Formats

Lab 7 - Configuring and Verifying Extended ACLs

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Lab 7 - Configuring and Verifying Extended ACLs

Uploaded by

Copyright:

Available Formats

Lab 7 – Configuring and Verifying Extended ACLs

Device Interface IP Address Subnet Mask Default Gateway

R1 G0/1 192.168.10.1 255.255.255.0 N/A

Part 1: Set Up the Topology and Initialize Devices

Step 1: Cable the network as shown in the topology.

Step 2: Initialize and reload the routers and switches.

Part 2: Configure Devices and Verify Connectivity

Step 1: Configure IP addresses on PC-A and PC-C.

Step 2: Configure basic settings on R1.

Step 3: Configure basic settings on ISP.

f. Assign a clock rate of 128000 to the S0/0/1 interface.

Step 4: Configure basic settings on R3.

Step 5: (Optional) Configure basic settings on S1 and S3.

Step 6: Configure OSPF routing on R1, ISP, and R3.

Step 7: Verify connectivity between devices.

Were your pings successful? ________

Part 3: Configure and Verify Extended Numbered and Named ACLs

??(config)# ip access-list extended LAB7

Where should the extended ACL LAB7 be implemented?

a. Apply LAB 7 to the G0/1 interface.

Router Interface Summary Table

Router Interface Summary

You might also like