Escalade Escalade ESV Suburban Tahoe Yukon Yukon XL Electrical Body Builders Manual Service Manual 2017 en US 1
Escalade Escalade ESV Suburban Tahoe Yukon Yukon XL Electrical Body Builders Manual Service Manual 2017 en US 1
Escalade Escalade ESV Suburban Tahoe Yukon Yukon XL Electrical Body Builders Manual Service Manual 2017 en US 1
FOR
You will note that the section numbers are non-sequential as we have provided only those
that are believed to be the most pertinent to the Upfitter community and best suited to their
needs.*
This new usage of the Service Information provides the opportunity for us to remain
consistent with the changes that take place throughout the model year and to provide you
updated information in a more timely fashion.
The vehicle identification number (VIN) plate is the legal identifier of the vehicle. The VIN plate is located on the upper left corner of the instrument panel (I/P). The VIN number can be seen through the windshield from the outside
of the vehicle:
K 4x4
6 Series A Tahoe LS
B Tahoe LT
C Tahoe Premier
E Tahoe FL
G Suburban LS
J Suburban Premier
K Suburban FL
L Suburban HD LS
M Suburban HD LT
7 Restraint System E Active Manual Belts, Airbags – Driver and Passenger – Front
(1st row), Front Seat Side (1st row), Roof Side (All seating
rows)
8 Engine Type C RPO L83, Engine – Gas, 8 CYL, 5.3L,SIDI VVT, AFM, E85
MAX, Aluminum, GM
G RPO L96, Engine – Gas, 8 CYL, 6.0L, SFI, E85 MAX, IRON,
GM
J RPO L86, Engine – Gas, 8 CYL, 6.2L, SIDI VVT, AFM, E85
MAX, Aluminum, GM
The vehicle identification number (VIN) plate is the legal identifier of the vehicle. The VIN plate is located on the upper left corner of the instrument panel (I/P). The VIN number can be seen through the windshield from the outside
of the vehicle:
4 4x4
6 Series A Escalade
B Escalade, Luxury
D Escalade, Platinum
G Escalade ESV
7 Restraint System K Active Manual Belts, Airbag – Driver and Passenger – Front
(1st row), Front Seat Side (1st row), Front Inboard Seat Side
(1st row), Roof Side (All seating rows)
The vehicle identification number (VIN) plate is the legal identifier of the vehicle. The VIN plate is located on the upper left corner of the instrument panel (I/P). The VIN number can be seen through the windshield from the outside
of the vehicle:
2 4x4
B Yukon SLT
C Yukon Denali
F Yukon XL SLE
G Yukon XL SLT
H Yukon XL Denali
7 Restraint System E Active Manual Belts, Airbags – Driver and Passenger – Front
(1st row), Front Seat Side (1st row), Roof Side (All seating
rows)
J RPO L86, Engine – Gas, 8 CYL, 6.2L, SIDI VVT, AFM, E85
MAX, Aluminum
Callout Description
1 Name of Manufacturer
Tire Placard
The tire placard label is located on the driver side B-pillar and displays the following assessments:
17 Paint Technology
Anti-Theft Label
20 The Federal law requires that General Motors label certain body parts on this vehicle with the VIN. The purpose of the law is to
reduce the number of motor vehicle thefts by helping in the tracing and recovery of parts from stolen vehicles.
Labels are permanently affixed to an interior surface of the part. The label on the replacement part contains the letter R, the
manufacturer's logo, and the DOT symbol.
The anti-theft label must be covered before any painting, and rustproofing procedures, and uncovered after the procedures.
Failure to follow the precautionary steps may result in liability for violation of the Federal Vehicle Theft Prevention Standard and
possible suspicion to the owner that the part was stolen.
RPO Description
AP9 NET-CONVENIENCE
CK4 COUNTRY-GREECE
CL5 COUNTRY-PERU
CL6 COUNTRY-BOLIVIA
CS2 COUNTRY-NIGERIA
CS5 COUNTRY-ANGOLA
CT1 COUNTRY-BELGIUM
CT2 COUNTRY-AUSTRIA
CT3 COUNTRY-GERMANY
CT5 COUNTRY-NETHERLANDS
CT6 COUNTRY-ITALY
CT7 COUNTRY-DENMARK
CT8 COUNTRY-PORTUGAL
CT9 COUNTRY-SPAIN
CU2 COUNTRY-FINLAND
CU3 COUNTRY-FRANCE
CU4 COUNTRY-SWEDEN
CU5 COUNTRY-SWITZERLAND
CU7 COUNTRY-KUWAIT
CV3 COUNTRY-MEXICO
CV4 COUNTRY-ISRAEL
CV5 COUNTRY-JAPAN
CV6 COUNTRY-CHILE
CW1 COUNTRY-KOREA
CW5 COUNTRY-VENEZUELA
CX0 COUNTRY-AZERBAIJAN
CX2 COUNTRY-COLOMBIA
CX3 COUNTRY-ECUADOR
CX9 COUNTRY-LEBANON
CY2 COUNTRY-JORDAN
CZ3 COUNTRY-RUSSIA
D2D COUNTRY-PHILIPPINES
D2O COUNTRY-CURACAO
D2Y COUNTRY-ANTIGUA
D3B COUNTRY-BERMUDA
D3H COUNTRY-BELARUS
D3I COUNTRY-BARBADOS
D3M COUNTRY-GUATEMALA
D3P COUNTRY-HAITI
D3Q COUNTRY-HONDURAS
D4G COUNTRY-BAHAMAS
D4X COUNTRY-ARUBA
D5D COUNTRY-NICARAGUA
D5K COUNTRY-SURINAM
DMQ DECAL-ALASKAN
DPU COUNTRY-BONAIRE
E7C COUNTRY-LIBYA
EF5 COUNTRY-PANAMA
EXP EXPORT-
GGC GRILLE-CUSTOM
NE1 CERTIFICATION-EMISSION,
GEOGRAPHICALLY RESTRICTED
REGISTRATION FOR VEHICLES UP TO 14,000
LBS GVW (USE 2003 MDL YR
T4L HEADLAMPS-LED
T79 LAMP-FOG, RR
TL1 GRILLE-SPECIAL
U2L RECEPTION-HD
UF2 LAMP-CARGO
UHL VEHICLE-U-HAUL
UL2 FREQUENCIES-EUROPEAN
UV6 DISPLAY-HEAD UP
V76 HOOK-TOW
VNX GRILLE-NONE
Z49 COUNTRY-CANADA
Driver
B+ L
O
C
X51L
Fuse Block
F43DL F18DL - Instrument D
Panel Left E
30A 10A S
C
X1 36 16
X500 1 40 4
S79D
Window
1940 Switch -
RD/VT Driver
X505 22
A90
B+ Logic
1940
RD/VT
J519
6 2 3 1 5 10 7 8 11 12
1300 7628 1136 1150 6134 3265 3270 1124 6816 5697
GN/WH GN/VT GY/BK BK GN/YE BN/RD WH/VT BU/VT WH GY
Door Lock/
Indicator
Schematics X505 40
X505 30 31 29
Door Lock/
3265 Indicator
BN/RD Schematics
1842 745 1300 7628 1136 6134
RD/BU GY GN/WH GN/VT GY/BK GN/YE
X500 35
2 6 3 5 7 4
M74D
A90 Window
B+ Logic Motor - 3265
Driver YE/BN
X7 15
M74P K9
Window Body
M Motor - Control
Passenger Module
1
1150
BK
G311
L
B+ B+ O
C
S79D X51R
Window Fuse Block - D
Switch - F44DR F27DR Instrument E
Driver Panel Right S
30A 10A C
A90
Logic X1 20 X1 42
1340 840
RD/WH RD/BU
840
RD/BU
1340
RD/WH
Interior Lights Dimming
Schematics
18 14 15 13 (A45)
6 2 3 1 (-A45)
Door Lock/
Indicator 166 2765 167
Schematics YE/BK VT/GY BN/YE
1250
X605 30 31 29 BK
6134 1340 746 166 2765 167
1150 GN/YE RD/WH GY YE/BK VT/GY BN/YE
BK
4 2 6 3 5 7
K9 M74P
Body A90 Window
Control B+ Logic Motor -
Module Passenger
1250
BK
G311 G312
B+ B+ L
S79D O
X51L Window X51R C
Fuse Block Switch - Fuse Block -
- Instrument Driver Instrument D
F43DL Panel Left F44DR Panel Right E
30A 30A S
C
A90
Logic
X1 37 X1 19
1842 1340
RD/D-BU RD/WH
X700 1 X800 1
A90 A90
B+ Logic B+ Logic
6 7 2 3 5 6 7 2 5
1 1
M74LR M74RR
M Window M Window
Motor - Door Lock/ Motor - Door Lock/
Left Rear Indicator Right Rear Indicator
Schematics Schematics
2 2
G311 G312
Defogger
L
O
193 193 C
BN/VT RD/VT
B+ D
E
X53A S
K33 C
HVAC 65 30 Fuse
Control KR5 Block -
Module 2 Rear Rear
Defogger Body
X2 19 Relay
193 60 62
BN/VT Outside
Rearview
Mirror
Schematics 938
938 BN/VT
X216 13 BN/VT
30 F24RA
30A
35
293
BN/VT
-UTU/UTV UTU/UTV
J381
293 293
BN/VT BN/VT
P17 X490 1
(X88/Z88) (Z75) Info Theft Deterrent
Display System
P7 A26 A20 Schematics
Display HVAC Controls Radio/HVAC Controls Module 293
BN/VT
X900 6
A90
Logic 293
BN/VT
1150
BK J901
293
BN/VT
X2 1
E18
Rear
Defogger
Grid
X1 1
1450
BK
G311 G402
• 30A Fuse
• 5A Fuse
• 30A Fuse
S79D M74D
Window Window
Switch - Motor -
Driver Driver
K9
Body
Control
Module
Driver and Passenger Express Up and Express Down Power Window Motors
The driver and passenger doors contains a window motor is smart motor that will detect excessive resistance while performing the express up function and automatically reverse direction to prevent injury to any occupants that
may become trapped between the closing window and the door frame. The automatic reverse safety feature can be overridden by pulling and holding the window switch.
• 40A fuse
K33
HVAC
Control
Module
Horn
B+ L
O
C
X50A
Fuse Block -
Underhood D
E
KR3 S
C
Horn
Relay
F93UA
15A
X3 L6 X1 J2
28
BN/WH
-6J4 6J4
X273 A
28 29
BN/WH BN/GY
X5 19
K9
Body
Control
Module
X3 18
3287
GN/WH
X1 10
X85 2
Steering Wheel Air P12
Bag Coil Horn
X2 1
3287
RD
1
S33
Horn 1
Switch
2 150
BK
1050
BK
G210 G101
• HORN fuse
• Horn relay
• Horn switch
• Horn assembly
S33
Horn
Switch
K9
Body
Control
Module
P13
Horn
Assembly
System Operation
The vehicle horn system is activated under the following conditions:
• The BCM commands the horns ON under any of the following conditions:
– When the content theft deterrent system detects a vehicle intrusion—For further information refer to Theft Systems Description and Operation.
– When the panic button is depressed on the remote control door lock transmitter—For further information refer to Keyless Entry System Description and Operation (With ATH)Keyless Entry System Description and
Operation (Without ATH).
– When the keyless entry system is used to lock the vehicle, a horn chirp may sound to notify the driver that the vehicle has been locked. The notification feature may be enabled or disabled through personalization.
For further information refer to Keyless Entry System Description and Operation (With ATH)Keyless Entry System Description and Operation (Without ATH).
– When the OnStar® system is used to sound the horns if equipped—For further information, refer to OnStar Description and Operation (UE1)OnStar Description and Operation (UI3).
Circuit Operation
Battery positive voltage is applied at all times to the horn relay coil and the horn relay switch. Pressing either of the horn switches applies ground to the horn relay control circuit. The BCM may also apply ground to the horn relay
control circuit as described above. When the horn relay control circuit is grounded, the horn relay is energized and battery positive voltage is applied to the horns through the horn control circuit. The horns sound as long as ground
is applied to the horn relay control circuit.
L
O
C
P16 B200
Instrument Rain
Cluster Sensor D
Module E
S
C
A90
Logic
K9
Body
Control
Module
FTP
X2 10 X3 11 17 X1 11 16
5
B10B
Ambient
Light/
HVAC Sunload
Schematics Sensor
X1 14 10 3 1
S78 S30
6 Turn Signal/ AUTO Headlamp
1791 Multifunction Switch
BK/YE Switch
X215 10
1791 X1 13
BK/YE
J255 8
G218
K9
F19DR F10DL Body L
O
Control C
Module
D
X4 1 X5 18 X4 2 E
S
C
B+
X4 K1 X3 L2 M1
X50A
Fuse Block -
Underhood
KR48
Headlamp
High Beam
Relay
F95UA
10A
X1 D1 J4 H4 J5
711 311
WH WH
X110 2 3 X120 3 2
E13LA E13RA
712 711 312 312
Headlamp Headlamp
PU WH WH PU
Assembly - Assembly -
E4G E4E Left E4F E4H Right
Headlamp - Headlamp - Headlamp - Headlamp -
Left Low Left High Right High Right Low
Beam Beam Beam Beam
X110 1 4 X120 1 4
150 150 250 250
BK BK BK BK
G101 G102
B+ L
O
X50A C
Fuse Block -
Underhood
D
KR48 KR49 E
Headlamp Headlamp S
C
High Beam Low Beam
Relay Relay
X3 L2 X4 M3 X1 J4 A2 H4 C2
X110 3 2 X120 3 2
X5 18 13
E13LA E13RA
E4G Headlamp E4H Headlamp
Headlamp - Assembly - Headlamp - Assembly -
Left Low Left Right Low Right
Beam Beam
K9 711 712 1 2 4 311 312 1 2 4
Body WH PU WH PU
Control
Module
1 2 4 1 2 4
E4E 12V T7L E4F 12V T7R
Headlamp - Headlamp Headlamp - Headlamp
Left High Ballast - Left Right High Ballast -
Beam Beam Right
X110 1 4 X120 1 4
150 150 250 250
BK BK BK BK
G101 G102
K9
F10DL F19DR Body L
O
Control C
Module
D
X4 7 X5 7 E
S
C
7538 7539
GY/BU BU/BN
X4 J1 X3 G1
X50A
Fuse Block -
Underhood
X1 H2 H6
7538 7539
GY/BU BU/BN
X110 6 X120 6
E13LA E13RA
Headlamp Headlamp
E4AC Assembly - E4AD Assembly -
Park/ Left Park/ Right
7538 Daytime 7539 Daytime
GN Running GN Running
Lamp - Lamp -
Left Right
K166L K166R
Multifunction Multifunction
LED Control LED Control
Module - Left Module - Right
Headlamp Headlamp
150 250
BK BK
J110 J120
X110 1 4 X120 1 4
G101 G102
L
O
C
P16 B200
Instrument Rain
Cluster Sensor D
Module E
S
C
A90
Logic
K9
Body
Control
Module
FTP
X2 10 X3 11 17 X1 11 16
5
B10B
Ambient
Light/
HVAC Sunload
Schematics Sensor
X1 14 10 3 1
S78 S30
6 Turn Signal/ AUTO Headlamp
1791 Multifunction Switch
BK/YE Switch
X215 10
1791 X1 13
BK/YE
J255 8
G218
K9
F19DR F10DL Body L
O
Control C
Module
D
X4 1 X5 18 X4 2 E
S
C
B+
X4 K1 X3 L2 M1
X50A
Fuse Block -
Underhood
KR48
Headlamp
High Beam
Relay
F95UA
10A
X1 D1 J4 H4 J5
E13LA E13RA
Headlamp Headlamp
E4G E4E Assembly - E4F E4H Assembly -
712 Headlamp - 711 Headlamp - Left 311 Headlamp - 312 Headlamp - Right
PU Left Low WH Left High WH Right High PU Right Low
Beam Beam Beam Beam
K166L K166R
Multifunction Multifunction
LED Control LED Control
Module - Left Module - Right
Headlamp Headlamp
150 250
BK BK
J110 J120
X110 1 4 X120 1 4
G101 G102
K9
F10DL F19DR Body L
O
Control C
Module
D
X4 7 X5 7 E
S
C
7538 7539
GY/BU BU/BN
X3 L1 M4
X50A
Fuse Block -
Underhood
X1 J6 H3
7538 7539
GY/BU BU/BN
J116 J117
7538 7539
GY/BU BU/BN
7538 7539
GY/BU 8 18 BU/BN
E13LA 7538 7539 E13RA
Headlamp GY/BU BU/BN Headlamp
X110 6 Assembly - 4 X104 4 6 Assembly -
Left Right
E69L E69R
7538 7538 Multifunction 7539 Multifunction 7539
BK PK Lamp PK Lamp BK
Assembly - Assembly -
Front Fascia Front Fascia
K166L K167L Left K167R Right K166R
Multifunction Multifunction Multifunction Multifunction
LED Control LED Control LED Control LED Control
Module - Left Module - Module - Module - Right
Headlamp Front Fascia Front Fascia Headlamp
Left Right
E4C E4D
Daytime E4AL E4AM Daytime
Running Park/ Park/ Running
Lamp - Daytime Daytime Lamp -
Left Running Running Right
150 150 Lamp - 250 Lamp - 250
BK BK Left Lower BK Right Lower BK
J110 J118 J128 J120
G101 G102
L
B+ B+ O
C
X50A K9 X53A
Fuse Block - Body 64 Fuse
Underhood F10DL Control Block - D
E
T3U T3U Module T79 Rear S
Body C
KR46 F22RA
Front Fog 10A
Lamp X5 10 X1 15 12 X5 5 28
Relay
T3U T79 T79
X1 J3 X3 L5
2234
BN/VT 5 3
KR57
X100 3 10 6 Rear Fog
P16 S30 Lamp
Instrument Headlamp Relay
2234 (T3U) (T79) Cluster Switch
BN/VT 9 10
A90
Logic 8 122
YE/GY
X495 23
122
YE/GY
J101 J493
122 122
YE/GY YE/GY
2234 2234
BN/VT BN/VT
X88 Z75 X88 Z75
A A 1 A 1 A
E29LF E29RF E29LR E29LR E29RR E29RR
Fog Fog Fog Lamp Fog Lamp Fog Fog
Lamp - Lamp - - Left - Left Lamp - Lamp -
B Left Front B Right 2 Rear B Rear 2 Right B Right
Front Rear Rear
K9
Body L
O
Control C
Module
5V D
E
S
X2 26 X3 12 24 X1 22 X1 19 X2 13 7 C
X201 16 X4 3 8 9
X61A
Junction
Block -
Instrument
111 Panel
GN/WH
X8 19 20 8
X2 G E D 5
S78 S30
Turn Signal/ AUTO Headlamp
Multifunction Switch 552 598 526
Switch BK/GN GY/RD WH/GN Engine
Controls
Schematics
X2 C F
8
5361 5359 5360
BU/YE WH BK/BN
2 3 4 6
1851 1851 1850 B22
BK BK BK Brake
Pedal
Position
Sensor
1 5
K20 P16
Engine P9 Instrument
Control Driver Information Cluster
Module Center Display
A90
Logic
G218
B+ L
O
X50A C
Fuse Block -
30 86 Underhood
D
KR53 E
Park S
C
Lamps
Relay
87 85
X5 J3 X1 G1 H2 X4 J1 L5 X3 G1 X1 H6 F1
2109
GY/BN 7538 45 7539
-Y91 Y91 GY/BU BU BU/BN Y91 -Y91
Trailer
Connector/ X4 7 X5 22 7
Provision K9
F10DL F19DR Body
Schematics 709 709 7538 7539 309 309
Control BU/BN GY/BN GY/BN
VT/GY VT/GY GY/BU Module
X110 6 7 6 X120 6 7 6
E13LA E13RA
709 709 7538 Headlamp 7539 309 309 Headlamp
GN BU GN Assembly - GN BU GN Assembly -
Left Right
E4J E2LF A90 A90 E2RF E4K
Park Side Logic Logic Side Park
Lamp - Marker Marker Lamp -
Left Front Lamp - Lamp - Right
Left Right Front
Front Front
E4AC E4AD
Park/ Park/
Daytime Daytime
150 150 150 Running 250 Running 250 250
BK BK BK Lamp - BK Lamp - BK BK
Left Right
J110 J120
X110 1 4 X120 1 4
150 150 250 250
BK BK BK BK
G101 G102
L
B+ O
C
X50A
Fuse Block -
86 30 Underhood D
E
KR53 S
C
Park Lamps
Relay
85 87
X4 L5 X5 J3 X1 G1 F1
45 2109
BU GY/BN
709 309
VT/GY GY/BN
G101 G102
K9
F10DL F19DR Body L
O
Control C
Module
D
X5 2 X7 7 X6 21 E
S
1314 C
BU/WH
X3 F1 L8 F2
X500 41 X50A
Fuse Block -
Underhood
1314
BU/WH X1 F3 H1 M5
X525 3 1314 57
E17D BU/WH YE/GY X88 Z88 Z88
Outside
1314 Rearview
BU Mirror X101 2 6 X110 5 5 8
Glass -
X4 1 Driver E69L E13LA
1314 Multifunction 1314 1314 3204 Headlamp
BK 57 Lamp RD RD YE
E4Y E4Y BK Assembly -
Turn Signal Turn 1 Assembly - Left
Repeater Lamp - Signal E4LF K167L Front Fascia E4LF K166L
Left Repeater Turn Multifunction LED Left Turn Multifunction
Lamp - Signal Control Module - Signal LED Control
2 Lamp - Lamp -
Left Front Fascia Left Module - Left
X4 2 Left Front Left Front Headlamp
1150 1150
BK/RD BK
150 150 150 150
BK BK BK BK
X525 2 E4A E4LF
1150 Cornering J110 Turn
J118 Lamp - Signal
BK/RD
J517 Left Lamp -
Left Front
150 150 150
BK BK BK
1150
BK/WH
X101 1 X110 1 4
X510 5
150 150 150
1150 BK BK BK
BK
G311 G101
K9
F19DR F46DR Body L
O
Control C
Module
D
X4 3 X6 7 6 E
S
1315 C
GN/VT
X3 D1 M3 D2
X600 41 X50A
Fuse Block -
Underhood
1315
GN/VT X1 D3 J1 M4
X625 2 1315 58
GN/VT YE/WH X88 Z88 Z88
1315 E17P
BU Outside Rearview X104 2 6 X120 5 5 8
Mirror Glass -
X4 1 Passenger E69R E13RA
1315 Multifunction 1315 1315 3203 Headlamp
BK 58 Lamp RD RD YE Assembly -
E4Z E4Z BK
Turn Signal Turn 1 Assembly - Right
Repeater Lamp - Signal E4RF K167R Front Fascia E4RF K166R
Right Repeater Turn Multifunction LED Right Turn Multifunction
Lamp - Signal Control Module - Signal LED Control
2 Lamp - Lamp -
Right Front Fascia Right Module - Right
X4 2 Right Right Headlamp
1250 1250 Front Front
BK/RD BK
250 250 250 250
BK BK BK BK
X625 1 E4B E4RF
1250 Cornering J120 Turn
J128 Lamp - Signal
BK/RD
J617 Right Lamp -
Right
250 250 250 Front
BK BK BK
1250
BK/WH
X104 1 X120 1 4
X610 5
1250 250 250 250
BK BK BK BK
G312 G102
K9 L
F47DR F19DR F10DL F46DR F19DL Body O
Control C
Module
D
X5 1 X4 6 5 4 11 E
S
C
18 7542 7541 19
YE/BU GY/YE WH/YE BN/GN
X3 A1 X4 A2 C1 X3 C1
X50A
Fuse Block -
KR53 Underhood
Park Lamps
Relay
F43UA F42UA
15A 15A
X5 A2 A1 K2 K4 D3 A3
X485 1
BN D-GN YE YE D-GN BN
5065
VT/WH
E42L E42R
Tail Lamp Tail Lamp
Assembly - Assembly -
Left Right A
E4LR E5L E5E E5F E5R E4RR E6
Turn Stop Tail Tail Stop Turn Center
Signal Lamp - Lamp - Lamp - Lamp - Signal
Lamp - Left Left Right Right B High
Lamp - Mounted
Left Rear Right Stop
Rear Lamp
A90 A90
Logic Logic
BK BK
BK BK
BK BK
X410 6 X420 6
1750
BK
2150 1450
BK BK
K9 L
F47DR F46DR F19DL Body O
Control C
Module
D
X5 1 X4 4 11 E
S
C
18 19 5065
YE/BU BN/GN VT/WH
X3 A1 C1
X50A
Fuse Block -
KR53 Underhood
Park Lamps
Relay
F43UA F42UA
15A 15A
X5 A2 K2 K4 A3
18 709 309 19
YE/BU VT/GY GY/BN BN/GN
X410 2 5 X420 5 2
X485 1
BN YE YE BN
5065
VT/WH
E42L E42R
Tail Lamp Tail Lamp
RD Assembly - RD Assembly -
Left Right A
E5AS E5AT E5E E5F E5AU E5AV E6
Stop/Turn Stop/Turn Tail Tail Stop/Turn Stop/Turn Center
Signal Signal Lamp - Lamp - Signal Signal
Lamp - Lamp - Left Right Lamp - Lamp - B High
Mounted
Left Left Right Right Stop
Upper Lower Upper Lower Lamp
A90 A90
Logic Logic
BK BK
BK BK
BK BK
X410 6 X420 6
1750
BK
2150 1450
BK BK
K9 L
F47DR F19DR F10DL F46DR F19DL Body O
Control C
Module
D
X5 1 X4 6 X6 12 22 X4 5 4 11 E
S
C
18 7542 5356 5357 7541 19 5065
YE/BU GY/YE YE/BK VT/YE WH/YE BN/GN VT/WH
X3 A1 X4 A2 G6 H6 C1 X3 C1
X50A
Fuse Block -
KR53 Underhood
Park Lamps
Relay
X5 A2 A1 G1 K2 K4 H1 D3 A3
5065
BN D-GN D-BU YE YE D-BU D-GN BN VT/WH
D A E B B E A D
E42L E42R
K174L Tail Lamp K174R Tail Lamp
Multifunction Assembly - Multifunction Assembly -
LED Control Left LED Control Right
Module - Module -
Left Tail Right Tail
Lamp Lamp A
E4LR E5L E5E E5F E5R E4RR E6
Turn Stop Tail Tail Stop Turn Center
Signal Lamp - Lamp - Lamp - Lamp - Signal B High
Lamp - Left Left Right Right Lamp - Mounted
Left Rear Right Stop
Rear Lamp
C C
1750 2150
BK BK
1450
BK
K9 L
F47DR F19DR F10DL F46DR F19DL Body O
Control C
Module
D
X5 1 X4 6 X6 12 22 X4 5 4 11 E
S
C
18 7542 5356 5357 7541 19
YE/BU GY/YE YE/BK VT/YE WH/YE BN/GN
X3 A1 X4 A2 G6 H6 C1 X3 C1
X50A
Fuse Block -
KR53 Underhood
Park Lamps
Relay
5065
VT/WH
F43UA F42UA
15A 15A
X5 A2 A1 G1 K2 K4 H1 D3 A3
X485 1
18 7542 5356 709 309 5357 7541 19
RD YE OG GN GN OG YE RD
5065
E42L E42R VT/WH
K174L Tail Lamp K174R Tail Lamp
Multifunction Assembly - Multifunction Assembly -
Left Right A
LED Control LED Control
Module - Module - E6
Left Tail Right Tail Center
Lamp Lamp B High
Mounted
E4LR E5L E5E E5F E5R E4RR Stop
Turn Stop Tail Tail Stop Turn Lamp
Signal Lamp - Lamp - Lamp - Lamp - Signal
Lamp - Left Left Right Right Lamp -
Left Rear Right
Rear
1750 1750 2150 2150
BK BK BK BK
J410 J420
1750 2150
BK BK
X410 6 X420 6
1750 2150 1450
BK BK BK
K9 L
F11DL F19DL Body O
Control C
Module
D
X5 26 X4 13 E
S
C
38
BU/BN 6846
B+ GN/YE
X4 L3
X50A
Fuse Block -
Underhood
KR61
Trailer
Backup
Lamps
Relay
F34UA
10A X900 10
X2 F2 X5 C1
24
GN/WH
J453
24 24 24 24 6846 6846
GN/WH GN/WH GN/WH GN/WH GN/YE GN/YE
X410 1 1 X420 1 1
24 24
PU (X88) 24 PU (X88) 24
BK BK
24 24
WH (Z88) WH (Z88)
E42L E42R
A Tail Lamp A Tail Lamp 1 1
E5A E5A Assembly - E5B E5B Assembly - E7L E7R
Backup Backup Left Backup Backup Right License License
Lamp - Lamp - Lamp - Lamp - Plate Plate
B Left Left B Right Right 2 Lamp - 2 Lamp -
Left Right
BK BK
J410 J420
X410 6 X420 6
550 1750 2150
BK BK BK
F47DR K9 L
Body Control
Module O
C
X7 8 D
E
5996 S
GY/GN C
J382
5996 5996
GY/WH A24LR A24RR GY/GN A24P
Door Door Door
A24D Handle Handle Handle
3 Door Handle 3 Assembly - 3 Assembly - 3 Assembly -
5996 Assembly - 5996 5996 Left Rear 5996 Right Rear 5996 5996 Passenger 5996 5996
GY/GN Driver Exterior GY/WH GY/GN Exterior GY/GN Exterior GY/GN GY/GN Exterior GY/GN GY/GN
L
O
C
D
B+ E
S
C
X51L
Fuse Block
- Instrument
F26DL Panel Left
15A
X2 27 14
7X6/7X7 7X7
4640 4140
RD/VT RD/GY
A A
E35L E35R
Exterior Exterior
Spot Spot
Lamp - Lamp -
Left Right
L
K9 O
Body C
F46DR Control
Module
D
E
S
C
X1 14 X7 19 X7 3
D07-DCK
6815
WH/BN
X225 4
X316 5 6 X300 28
2 3 1
S12 S5
DOOR Dome Center
OFF ON Lamp Console
Switch Compartment
Lamp Switch
2
1
6815
WH/BN
1
E28
Center
Console
Compartment
Lamp
2
1050 1050
BK BK
G210
K9
F47DR Body L
O
Control C
Module
D
X7 1 E
S
C
157
GY
SWB-Z75 Z75/-SWB
J322
2 2 2 2
K9 L
F46DR Body O
Control C
Module X61A
Junction
Block - D
X7 3 E
Instrument S
6815 Panel C
WH/BN
R
X2 23
6815 157
X61A BN/WH GY
Junction
Block -
Instrument
Panel
X3 25 Interior Lights
Schematics
6815
WH/BN J312
J311
AZ3 AZ3 AZ3 AZ3 -U42 -U42 U42 U42 -DNU -DNU DNU DNU
6815 6815 6815 157 6815 157 6815 157 6815 157 6815 157 6815 157 6815 157
WH/BN WH/BN WH/BN GY WH/BN GY WH/BN GY WH/BN GY WH/BN GY WH/BN GY WH/BN GY
X Y
X316 X316
E31L E31R
Sunshade Sunshade
Mirror Mirror
Lamp - Lamp -
Left Right
G210
L
O
C
D
X51L E
Fuse Block S
KR73 - Instrument C
Ignition Panel Left
Main
Relay
F25DL
10A J311 J312
X Y
X3 14
X316 11 7 21
-DRZ
J302
4 4
G210
K9 L
F19DL Body O
Control C
Module
D
E
X1 23 S
C
7558
VT/GN
X4 21
X61A
Junction
Block -
Instrument
Panel
X3 42
7558
VT/GN
-U42/DNU U42/DNU
J319
7558
U42 DNU
VT/GN
X316 9
X2 15 (ULT)
X2 1 (-ULT) X2 1
1 P22A P22B
E38 Video Video
Flood Lamp Display - Display -
2nd Row 3rd Row
2 - Center
Console
X2 2 (-ULT) X2 2
X2 5 (ULT)
G210
K9
F19DL Body L
Control O
C
Module
D
X7 22 E
S
C
7557
WH/YE
J384
X505 2 X605 2
7557 7557
WH/YE WH/YE
X310 46 X320 46
7557 7557 7557 7557 7557 157 157 7557 7557 7557
WH/YE WH/YE WH/YE WH/YE WH/YE GY GY WH/YE WH/YE WH/YE
1 1 1 1 1 1
1050 1851 1150 1150 1150 1150 1250 1250 1250 1250
BK BK BK BK BK BK BK BK BK BK
2 2 2 2 2 2
1150 1150 1150 1250 1250 1250
BK BK BK BK BK BK
L
O
C
J384 J384
S T
D
E
S
C
7557 7557
WH/YE WH/YE
X700 3 X800 3
7557 7557
WH/YE WH/YE
X705 2 X805 2
7557 7557
WH/YE WH/YE
J720 J820
1 1 1 1 1 1
E1E E55LR E1LR E1F E55RR E1RR
Accent Flood Accent Accent Flood Accent
Lamp - Lamp - Lamp - Lamp - Lamp - Lamp -
2 2 Left Rear 2 2 Right 2 Right 2
Left Rear Left Rear Right
Door Door Door Rear Rear Door Rear
Handle Pocket Door Pocket Door
Handle
G311 G312
K9
Body Control L
F46DR O
Module C
5V D
E
X2 8 9 X1 13 7 S
C
6817
YE
J208
6817
U V YE
X300 41 2 11 12 7
J325 X51L
Fuse Block S30
- Instrument Headlamp
6817 Panel Left 6817 6817 6817 6817 6817 6817 6817 Switch
5K 470
YE YE YE YE YE YE YE YE
7 8 1
S38 S27
Ignition Head-Up
Z75 X88/Z88 Mode Display
Switch Switch 8
Trailer Brake
Control X307 5
Schematics 2
6817 4
YE
8 S76
7631 Trailer Brake Control
BK/BN Switch
X5 14 5 5 6 7
X61A S140 S77 S91 S48A
Junction Media Disc Transfer Park Multifunction
Block - Eject Case Shift Brake Switch -
Instrument Switch Control Control Instrument
Panel Switch Switch Panel
X1 27 6 6
8 8
7631 1
BK/BN
S145
Center
Console
Compartment
X185 6 Cooler Switch
3
19
K38
Chassis
Control
Module
J208
L
U O
C
D
6817 E
S
YE C
X4 6
X61A
Junction
Block -
Instrument
Panel
X3 27
6817
YE
J325
X316 10
J303
X2 6 (ULT)
1 1 D X2 4 (-ULT) D X2 4
E37H E37J E37B P22A E37C P22B
Dome/ Dome/ Dome/Reading Video Dome/Reading Video
Reading Reading Lamps - 2nd Display - Lamps - 3rd Row Display -
Lamps - Left Lamps - Row 2nd Row 3rd Row
Roof Rail Right Roof
Rail
4 4 B X2 2 (-ULT) B X2 2
X2 5 (ULT)
G210
L
O
C
D
E
S
C
X316
W
6817
YE
J303
1 1 4 3 2 3 2 2
E37EL E37ER S12 S72 S25 S43 S45B S51
Dome/ Dome/ Dome Sunroof Garage Content Liftgate Telematics
Reading Reading Lamp Switch Door Theft Control Button
Lamps - Lamps - Switch Opener Deterrent Switch - Assembly
Front Front Sensor Interior
Overhead Overhead Disable
4 Switch
Console Left Console 2 6
4 4 Right 1 7 1
G210
J208 K9
Body L
V Control O
C
Module
6817 D
E
BN S
X2 3 C
X51L
F12DL Fuse Block
2A - Instrument
Panel Left
X2 4
6136
BN
P16 A10
Instrument Inside
Cluster Rearview
Mirror
X201 38 UK3
X2 6 1 (X88/Z88) 6
2 (Z75)
-UK3
6817
YE (X88/Z88) (X88/Z88)+(KA1/KB6) (X88/Z88)+(KA1/KB6)
6136
YE
6817
OG/BK (Z75) S31D S31P A34 P17
Seat Seat HVAC Info
Heating and Heating and Controls - Display
Cooling Cooling Auxiliary Module
Switch - Switch -
2 (Z75) Driver Passenger
6 (X88/Z88) A90 A90
S70L Logic Logic
Steering Wheel
Controls Switch -
Left
A90 A90
Logic Logic
1 (X88/Z88)
6 (Z75)
1050 1050
BK BK
G210
K9
Body L
F46DR Control O
C
Module
D
E
X7 9 S
C
6817
YE
J383
S52
Outside 6817
6817
Rearview YE
YE
Mirror
Switch
A90
Logic X500 29 X600 29
6817 6817
YE YE
X505 1 X605 1
A45
6817 6817 6817 6817
YE YE YE YE
-A45 A45
17 (A45)
1 6 2 1 5 (-A45)
S13D S52 S47D S13P S79P
Door Lock Outside Seat Memory Door Lock Window Switch -
Switch - Rearview Switch - Driver Switch - Passenger
Driver Mirror Passenger
Switch
4 5 1 4 1 (-A45)
13 (A45)
5978
BK/BU
S79D S79LR S79RR
A90 Window A90 Window A90 Window
Logic Switch - Logic Switch - Logic Switch - X505 32
Driver Left Rear Right Rear 5978
BK/BU
X500 21
1150
BK
5978
BK/BU
1 5 5 X310 40
1150 1150 1250 1150 1150 5978 1250 1250
BK BK BK BK BK BK/BU BK BK
X6 11
K40D
Seat Memory
Control Module -
Driver
G311 G312
K9 L
Body O
5W4/9C1 F38DR F11DR Control C
Module
Auxiliary
Battery D
E
Schematics 300 X5 14 X1 5 S
C
VT/BN
300 6816
VT/BN WH
X1 33 X5 34
X61A
Junction
Block -
Z X61A Instrument
Panel
X5 38 18 37
300
VT/BN
X88/Z88/Z75-UGN Z75+UGN
X307 13
5852 3152 3152 5852 1560 1565 1566 1561 1563 2546
GN/BN WH WH GN/BN BN VT/WH BN/BK GY/GN GN/BK GY/BK
X1 3 4 X1 3 2 X2 12 3 14 11 13 3
K182 B174W K124 K69 K175
Parking Frontview Active Transfer Center
Assist Camera - Safety Case Console
Control Windshield Control Control Compartment
Module Module Module Cooler
Control
Module
G311
L
O
C
D
E
S
K9 C
Body
Control
Module
X2 6
5967
GY
X5 6
X61A
Junction
X61A Z Block -
Instrument
Panel
X1 47 25
6816 5697
WH GY
X500 16 32
6816 5697
WH GY
X505 3 45
6816
WH
11
S79D
Window
Switch -
Driver
12
5697
GY
K9 L
Body O
Control C
Module
D
E
S
X2 6 C
5967
GY
X5 6
X61A
Junction
X61A Z Block -
Instrument
Panel
X5 39 X1 47 25
6816 5697
WH GY
J304
X600 6 X500 16 32
6816 5697
WH GY
X505 3
6816
WH
3 11
S140 S79D
Media Disc Window
Eject Switch -
Switch Driver
6 12
2550 5697
BK GY
X505 45
G325
K9 S31D L
Body Seat O
Control C
KB6 Heating and
Module Cooling
Switch - D
Driver E
S
C
A90
Logic
(X88/Z88)+(KA1/KB6)
2517 2516
BN/WH YE/VT
2 (X88/Z88)
8 (Z75)
X4 22 2
X61A A90 6816
Junction Logic WH (X88/Z88)
Block -
Instrument 6816
Panel VT (Z75)
X3 36 22
5 (Z75)
7 (X88/Z88)
-DRZ -DRZ S70L
Steering Wheel
2517 2516 Controls Switch -
BN/WH YE/VT Left
7 6
A10
Inside 8 (X88/Z88)
Rearview 12 (Z75)
Mirror
5884
5 PK
1050 K32
BK Steering
Wheel
Heating
Control
Module
G210
• Backup lamps
• Headlamps
• Stop lamps
• When the headlamp switch is placed in the ON position, for normal operation
• When the headlamp switch is placed in the AUTO position, for automatic lamp control
• When the headlamp switch is placed in the AUTO position, with the windshield wipers ON in daylight conditions, after a 6 second delay
The BCM will also command the low beam headlamps ON during daylight conditions when the following conditions are met:
• Windshield wipers ON
When the BCM commands the low beam headlamps ON, the vehicle operator will notice the interior backlighting for the instrument cluster and the various switches with backlighting control will dim to the level of brightness
selected by the instrument panel dimmer switch.
• Never open the high intensity discharge system ballast or the arc tube assembly starter.
• Never probe between the high intensity discharge system ballast output connector and the arc tube assembly.
The body control module (BCM) monitors three signal circuits from the headlamp switch. When the headlamp switch is in the AUTO position, all three signal circuits are open. When placed in the AUTO position, the BCM
monitors inputs from the ambient light sensor to determine if headlamps are required or if daytime running lamps will be activated based on outside lighting conditions. When the headlamp switch is placed in the OFF position, the
headlamp switch headlamps OFF signal circuit is grounded, indicating to the BCM that the exterior lamps should be turned OFF. With the headlamp switch in the PARK position, the headlamp switch park lamps ON signal circuit
is grounded, indicating that the park lamps have been requested. When the headlamp switch is placed in the HEADLAMP position, both the headlamp switch park lamps ON signal circuit and the headlamp switch headlamps ON
signal circuit are grounded. The BCM responds to the low beam request by applying ground to the low beam relay control circuit which energizes the low beam relay. With the low beam relay energized, the switch contacts close
allowing battery voltage to flow through the low beam fuses. Battery voltage is then applied from the fuses, through the low beam control circuits to the left and right headlamp ballast located in each headlamp assembly. When
battery voltage is applied to the headlamp ballast through the low beam control circuits, the ballast charge the starter to start the lamp. High intensity discharge (HID) headlamps do not have filaments like traditional bulbs, instead
the starter uses a high voltage transformer to convert the input voltage into a higher voltage. This increased voltage is used in order to create an arc between the electrodes in the bulb.
• Lights go out, caused when the ballast detects excessive, repetitive bulb re-strike
Input power to the ballast must be terminated in order to reset the ballast's fault circuitry. In order to terminate the input power to the ballast, turn the lights off and back on again. Turning the lights off and back on again resets all
of the fault circuitry within the ballast until the next occurrence of excessive, repetitive bulb re-strikes. When excessive, repetitive bulb re-strikes occur, replace the starter/arc tube assembly. The ballast will begin the start-up
process when the starter/arc tube assembly is replaced. Repeatedly resetting the input power can overheat the internal components and cause permanent damage to the ballast. Allow a few minutes of cool-down time in between
reset attempts.
Light Color
White light has a different color rating than regular headlamps. The range of white light that is acceptable is broad when compared to halogens. Therefore, some variation in headlight coloring between the right and left headlamp
will be normal. One high intensity discharge (HID) at the end of the normal range may appear considerably different in color from one at the other end of the range. Difference in color is normal. Replace the arc tube only if the arc
tube is determined to be at the bulb failure stage.
• Vehicle ON
• Delay
Note: AHBA may not operate properly if any of the following conditions exist:
• Approaching and preceding vehicles lamps are undetectable due to dirt, snow, road spray, smoke, fog, or any other airborne conditions.
• The vehicle is being driven on winding or hilly road conditions which would make any on coming vehicle headlamps undetectable by the AHBA.
• Manually operating the headlamp dimmer switch from neutral to high beam position
• AHBA is deactivated automatically when the front or rear fog lamps are turned ON
• The shift lever is out of the PARK position for vehicles equipped with automatic transmissions or the parking brake is released for vehicles with manual transmissions
Flash to Pass
When the turn signal/multifunction switch is momentarily placed in the flash to pass position, ground is applied to the turn signal/multifunction switch. The turn signal/multifunction switch applies ground to the body control module
(BCM) through the flash to pass switch signal circuit. The BCM responds to the flash to pass request by applying ground to the high beam relay control circuit. This energizes the high beam relay, closing the switch side contacts
of the high beam relay, applying battery voltage to the 3 pin high beam fuse. Battery voltage is applied from the high beam fuse through the high beam control circuit to the high beam headlamp assemblies. This causes the high
beam headlamps to illuminate at full brightness momentarily.
Hazard Lamps
The hazard flashers may be activated in any power mode. The hazard switch signal circuit is momentarily grounded when the hazard switch is pressed. The body control module (BCM) responds to the hazard switch signal input
by supplying battery voltage to all four turn signal lamps in an ON and OFF duty cycle. When the hazard switch is activated, the BCM sends a serial data message to the instrument panel cluster requesting both turn signal
indicators to be cycled ON and OFF.
The instrument panel dimmer switch controls the brightness of the interior backlighting components. When the instrument panel dimmer switch is placed in a desired brightness position, the body control module (BCM) receives a
signal from the instrument panel dimmer switch and responds by applying a pulse width modulated voltage to the hazard switch light emitting diode (LED) backlighting control circuit illuminating the LED to the desired level of
brightness.
Stop Lamps
Backup Lamps
With the engine ON and the transmission in the REVERSE position, the transmission control module (TCM) sends a serial data message to the body control module (BCM). The message indicates that the gear selector is in the
REVERSE position. The BCM applies battery voltage to the backup lamps control circuit illuminating the backup lamps. Once the driver moves the gear selector out of the REVERSE position, a message is sent by the TCM via
serial data requesting the BCM to remove battery voltage from the backup lamps control circuit. The engine must be ON for the backup lamps to operate.
Trailer Lamps
Backup Lamps
For backup lamp operation, the backup lamp relay is supplied with battery voltage at all times. With the engine running and the transmission in the reverse position, the transmission control module (TCM) sends a serial data
message to the body control module (BCM). The message indicates that the gear selector is in the reverse position. The BCM energizes the backup lamp relay by applying battery voltage to the backup lamp relay control circuit.
When the backup lamp relay is energized, the relay switch contacts close and battery voltage is applied through the backup lamp fuses to the backup lamp control circuits which illuminates the backup lamps. Once the driver
moves the gear selector out of the reverse position, a message is sent by the TCM via serial data requesting the BCM to remove battery voltage from the backup lamp relay control circuit.
Park Lamps
When the headlamp switch is placed in the HEAD or PARK position, ground is applied to the park lamp switch ON signal circuit to the body control module (BCM). The BCM responds by applying voltage to the park lamps, tail
lamps, license lamps, and trailer park lamps control circuits illuminating the park, tail, license, and trailer park lamps.
Stop Lamps
For stop lamp operation, the left and right trailer stop/turn signal lamp relay’s are supplied with battery voltage at all times. The brake pedal position sensor is used to sense the action of the driver application of the brake pedal.
The brake pedal position sensor provides an analog voltage signal that will increase as the brake pedal is applied. The body control module (BCM) provides a low reference signal and a 5 V reference voltage to the brake pedal
position sensor. When the variable signal reaches a voltage threshold indicating the brakes have been applied, the BCM energizes the left and right trailer stop/turn signal lamp relay’s by applying voltage to the left and right stop
lamp relay control circuits. With the left and right trailer stop/turn signal lamp relay’s energized, the relay switch contacts close and battery voltage is applied through the left and right trailer stop/turn signal fuse’s to the trailer stop
lamp control circuits which illuminates the trailer stop lamps.
• Dome lamps
• Reading lamps
Dome Lamps
The dome lamp switch has 3 positions: DOOR, OFF, and ON. The ON position provides a ground for continuous operation and the dome lamp will remain illuminated until the switch is placed in either the DOOR or OFF position.
When in the DOOR position, the dome lamp operation is controlled by the body control module (BCM). When any door is opened, the door ajar switch contacts close and the BCM receives a door-open input. The BCM illuminates
the dome lamp when any door is opened or a door lock/unlock request is activated with the key fob. After all doors have been closed, the dome lamp will remain illuminated approximately 3 seconds after the last door closes. When
the driver places the dome lamp switch in the OFF position, the dome lamp will be disabled. In the event that the dome lamp were to remain illuminated for more than 10 minutes with the ignition switch in the OFF position, the
BCM will deactivate the dome lamp control circuit to prevent total battery discharge. The dome lamps will turn OFF using the theater dimming feature when controlled by the BCM.
Reading Lamps
The inadvertent power supply voltage circuit from the BCM provides battery positive voltage to each reading lamp. When a reading lamp switch is activated, the switch contacts close providing a path to ground and the reading
lamp illuminates. If the operator inadvertently leaves a reading lamp ON, the BCM will turn all interior lamps OFF after 10 minutes has passed since any switch activation has been detected by the BCM.
• Headlamp switch
• Hazard switch
With the headlamp switch in the PARK or HEAD position, the park lamp switch signal circuit provides an input to the body control module (BCM). The BCM responds by applying voltage to the park lamps as well as the backlight
dimming control circuits illuminating all components with interior backlighting. All interior backlighting turns ON at the dimming level indicated by the instrument panel dimmer switch. The instrument panel instrument panel dimmer
switch is a momentary type switch and utilizes a resistor ladder to increase and decrease the brightness of the interior backlighting components. The instrument panel dimmer switch provides a voltage signal to the BCM that will
increase as the brightness of the lights are increased and decrease as the brightness of the lights are decreased. The BCM provides a low reference signal and a B+ circuit to the instrument panel dimmer switch. When the
instrument panel dimmer switch is held in the desired position, the dimmed voltage setting is applied from the instrument panel dimmer switch through the instrument panel dimmer switch signal circuit to the BCM. The BCM
interprets the signal and applies a pulse width modulated voltage through the backlighting control circuits illuminating the interior backlighting to the requested level of brightness.
X51L X50A L
KR73 Fuse Block Fuse Block - O
A1 KR61
Ignition - Instrument Underhood C
Mirror Trailer Backup Lamps Relay
Main Panel Left Dimming
Relay
F34UA D
E
F36DL 10A S
10A C
E17D
1690 1691 Outside OnStar/
BN BK Rearview Telematics
X4 A3
Mirror Schematics
X3 13
X525 4 1 Glass -
Driver Object
1690 1691 Detection
1739 BN BN/BK 24 Schematics
VT/GN GN/WH
X510 2 16 A9A
-AZ3 AZ3 Outside -UVC UVC 24
Rearview GN/WH
1690 1691 Mirror -
J320 YE/BK BK/YE Driver J386
2516 2517 2514 2515
X500 5 6 YE/VT BN/WH GN/WH GN/BK
1739 24
VT/GN GN/WH
1690 1691
YE/WH BK/YE
X2 10 9 15 X4 2 22 7 19
X61A
Junction
Block -
Instrument
Panel
X3 8 9 13 22 36 21 17
2 9 8 1 6 7 3 4
A10
S51 Inside
A90 Rearview
IGN R Logic 1.5K 1.5K 10K Telematics
Button Mirror
Assembly
N A1
Mirror Dimming
1050
BK
G210
COAX
1690 1691
YE/WH BK/YE
X2 10 9 15
X353 GY COAX
X61A
Junction
Block -
Instrument
Panel
X3 8 9 13
1690 1691 24
YE/WH BK/YE GN/WH DRZ
COAX
X2 GY
X1 2 9 8 1
A10
Inside
Rearview
DRZ DRZ Mirror
1
IGN R D A90
Logic
(DRZ)
N A1 P7
Mirror Dimming Display
1050
BK
G210
B+ L
O
C
X51L
Fuse Block
F18DL Instrument
-
S79P K40D D
10A Panel Left E
Window Seat S
Switch - Memory C
Passenger Control
Module -
X1 16 Driver
1940
RD/VT
X500 40
7530
GN/WH
1940
RD/VT 10 9
S52
X505 22 Outside
Rearview
Mirror
Switch
1940 1940
RD/VT RD/VT
A90
B+ Logic
5V
J519
3 1 2 7 8 4 11 6 12 5
DL3/DR4 DL3/DR4
X505 10 12 13 14 6 11 7 8 9
1150 3394 3392 3395 3393 3390 3389 3391 3411 3412
BK GY/BN VT/RD WH/YE BK/BN VT/BU BN/BK YE/BN GY/WH WH/GN
X510 14 17 7 3 9 10 12 4 18
A9A
Outside
Rearview
Mirror -
Driver
M77D M78D
M M Outside Outside
Rearview M Rearview
Mirror Mirror
Motor - Folding
Driver Motor -
Driver
G311
B+ L
O
X51R C
Fuse Block -
F27DR Instrument S52 K40D D
10A Panel Right Outside Seat E
Rearview Memory S
C
Mirror Control
Switch Module -
X1 42 Driver
840
RD/BU
X600 11
840
RD/BU
X605 22
840 7530
RD/BU GN/WH
16 9
S79P
A90 Window
B+ Logic Switch -
Passenger
5V
13 5 4 11 6 2 3 8 1 7
DL3/DR4 DL3/DR4
X605 10 12 13 14 6 7 11 8 9
1250 3401 3399 3403 3400 3397 3398 3396 3413 3414
BK BU/YE YE/RD VT/WH BK/GN YE/VT WH GN/BK YE/WH BU/GY
X610 14 17 7 3 9 12 10 4 18
A9B
Outside
Rearview
Mirror -
Passenger
M77P M78P
M M Outside Outside
Rearview M Rearview
Mirror Mirror
Motor - Folding
Passenger Motor -
Passenger
G312
B+ L
O
X51L C
Fuse Block
F18DL - Instrument
D
10A Panel Left E
S
C
X1 16
12
S52
Outside
1940 1940 Rearview
RD/VT RD/VT Mirror
DL3/DR4 Switch
A90
B+ Logic
J519
X500 40
L R L R
o o
7 3 10 1 8 4 5
X505 22 6 7 5 43 44 42
X500 38 4 36
X600 38 4 36
X510 9 12 10 X610 9 12 10
3390 3391 3389 3397 3398 3396
OG/BK WH GN OG/BK WH GN/WH
A9A A9B
Outside Outside
Rearview Rearview
Mirror - Mirror -
M77D Driver M77P Passenger
Outside Rearview Outside Rearview
M M Mirror Motor - M M Mirror Motor -
Driver Passenger
G311
S52 L
Outside O
Rearview C
Mirror
Switch
D
A90 E
S
Logic C
9 2
3411 3412
GY/WH WH/GN
X505 25 26
3411 3412
GY/WH WH/GN
X500 8 7
X600 8 7
3411 3412
GY/WH WH/GN
X510 4 18 X610 4 18
3411 3412 3411 3412
YE L-BU YE L-BU
A9A A9B
Outside Outside
Rearview Rearview
Mirror - Mirror -
Driver Passenger
M78D M78P
Outside Outside
M Rearview M Rearview
Mirror Mirror
Folding Folding
Motor - Motor -
Driver Passenger
K33
HVAC 193 L
Control B+ O
RD/VT C
Module
X53A A10
2 87 Fuse A90 Inside
X2 19 Logic D
KR4B Block - Rearview E
193 65 Outside Rearview Rear Mirror S
BN/VT Body C
Mirror Heater Relay
X216 13
9 8
193 8 1
BN/VT Defogger
Schematics DL3/DR4 DL3/DR4
1690 1691
340 YE/WH BK/YE
RD/VT
X3 8 9
56 F4RA X61A
15A Junction
57 Block -
Instrument
Panel
2267 X2 10 9
BN/YE
J379
X500 31 5 6 X600 31
2267 1690 1691 2267
BN/YE YE/WH BK/YE BN/YE
P17
Info X510 8 2 16 X610 8
Display
Module 2267 1690 1691 2267
BK BN BN/BK BK
A9A A9B
A90 X525 4 1 Outside Outside
Logic Rearview Rearview
Mirror - Mirror -
1690 1691 Driver Passenger
BN BK
X1 1 X1 1
E17D E17P
A1 Outside Outside Rearview
Mirror Dimming Rearview Mirror Mirror Glass -
Glass - Driver Passenger
X2 1 X2 1
1150 1250
BK BK
X510 11 X610 11
1150 1250
BK BK
Preliminary Procedure
Remove the windshield multifunction sensor mount bracket cover. Refer to CELL Link Error - Link target cell (cell ID 221811) is invalid for this
publication..
Procedure
1. Disconnect electrical connector.
2. Adjust the mirror to the full upward position.
3. Loosen the set screw located at the base of the mirror.
Procedure
1. Slide the mirror upward off of the rearview mirror button.
2. Refer to CELL Link Error - Link target cell (cell ID 72864) is invalid for this publication. for programming and setup
information, if required.
Procedures
1. Remove the windshield multifunction sensor mount bracket cover. Refer to CELL Link Error - Link target cell (cell ID
221811) is invalid for this publication..
2. Disconnect the electrical connector.
3. Adjust the mirror to the full upward position.
4. Loosen the set screw located at the base of the mirror.
Procedure
Slide the mirror upward off of the rearview mirror button.
Driver Outside Rearview Mirror with Automatic Day-Night System Operation (If Equipped)
The automatic day-night feature of the driver outside rearview mirror is controlled by the inside rearview mirror. The inside rearview mirror supplies control and low reference to the driver outside rearview mirror. At night, with the
automatic day-night feature enabled, the driver outside rearview mirror will automatically darken with the inside rearview mirror to reduce glare from headlamps behind the vehicle.
K40
Seat
Memory
Control
Module
S52 S79P
Outside Window
Rearview Switch -
Mirror Passenger
Switch
A9A A9B
Outside Outside
Rearview Rearview
Mirror - Mirror -
Driver Passenger
Mirror position is determined by both horizontal and vertical position sensors in each of the power mirrors. The outside mirror switch and passenger window switch supply a 5 V reference, low reference, and horizontal and vertical
position signal circuits to these sensors. The signal circuits are referenced from 5 V by the switches and the signal circuit voltage levels represent the mirror positions. The mirror positions are sent to the memory seat module
through the serial data circuit where they are stored for memory mirror operation. When the memory seat module receives a memory recall command, the memory seat module will send the go to position commands to the outside
mirror switch and passenger window switch. The switches will then drive the appropriate mirror motors to the commanded position sensor settings.
Heated Mirrors
• Mirror direction switch — Controls the left, right, up and down movements of the mirrors
• Mirror select switch — Allows the operator to select the mirror to be moved
• Left outside mirror — Contains both the horizontal and vertical mirror motors
• Right outside mirror — Contains both the horizontal and vertical mirror motors
Each of the outside power mirrors contains 2 motors. The up-down motor operates the vertical directions and the left-right motor operates the horizontal directions. Each of the power mirror motors are internally circuit breaker
protected.
S52
Outside
Rearview
Mirror
Switch
A9A A9B
Outside Outside
Rearview Rearview
Mirror - Mirror -
Driver Passenger
The mirror direction switch is a 4 position switch that allows the operator to move the selected mirror up, down, left or right.
The 4 positions of the direction switch have multiple switch contacts. When not in use, the directional contacts are isolated from any circuit. Each of the contacts are connected to opposing sides of the appropriate mirror motors
through the selector switch. The selector switch interrupts or completes these circuits depending on the position of the selector switch, L or R.
If the mirror select switch is placed in the L position and the up switch is pressed, battery voltage will be supplied to the driver outside mirror vertical motor through the driver mirror motor up control circuit and return to the mirror
switch through the driver mirror motor left/down control circuit, then to ground and the mirror will move up. If the down switch is pressed, the driver mirror motor left/down control circuit supplies battery voltage and the driver mirror
motor up control circuit completes the path to the mirror switch, then to ground and the mirror will move down.
The remainder of the mirror functions operate in the same manner as described above. Placing the mirror control switch in opposing positions, left/right or up/down, will reverse the voltage polarity to the mirror motor, utilizing the
same circuits and the mirror will move accordingly.
Heated Mirrors
The heated mirrors are controlled through the rear defog relay. Whenever the rear window defogger is turned ON, battery voltage is supplied to the mirror heater elements through the left and right mirror heater element control
circuits.
Liftglass Release
B+ L
O
X53A C
64 Fuse
F38DR K9 F11RA Block - D
Body 10A Rear E
Control Body S
43 C
Module
X6 15 5 X4 8
6188 4340
GY/YE RD/YE
P16 6 7
P9 Instrument KR162
Driver Information Cluster Liftgate Window
Center Display Unlatch Relay
6190 1303
A90 GY/GN VT/GY 16 15
Logic
6795
BU/YE
X490 3
6795
BU/YE
X900 26 28 25
TB4
6190 1303 1303 6795 1150
GY/GN VT/GY VT/GY BU/YE BK
2 4 1
S141 M33
Liftgate M Liftgate
Window A23C Window Latch
Unlatch Liftgate Assembly
Switch Latch
Assembly
1
3 2
G402 G311
B+ L
O
X53A C
64 Fuse
F19DL K9 F7RA Block - D
Body 10A Rear E
Control Body S
49 C
Module
X7 14 X6 5 X5 20 X5 11
P16 20 21
P9 Instrument KR95A
Driver Information Cluster Liftgate Unlatch
Center Display Relay
5797 1303
A90 YE/BU VT/GY 26 25
Logic
6128
BU/WH
X490 2
6128
BU/WH
X900 24 28 19
5797
YE/BU
1303 1303 6128
1 VT/GY VT/GY BU/WH
5797
YE/BU 2 3
S46B A23C
Liftgate Unlatch M Liftgate
Switch M33 Latch
Liftgate Assembly
Window Latch
Assembly
1450
BK 1
2
1450 1450
BK BK
G402
L
O
C
K9
Body
F13DR F13DR Control D
Module E
S
C
X6 1 4
294
BN/YE
J360
195 294
BU/WH BN/YE
Door Lock/
Indicator
Schematics
X1 29 X185 24
X51R
Fuse Block -
Instrument
86 30 Panel Right 294
KR114 BN/YE
Door Dead
Lock Relay
1
M27
85 87 87A M Fuel Fill
Door Unlatch
Actuator
2
Door Lock/
Indicator
Schematics
5911 5911
GY GY
X1 40 X185 25
295
GY
L
O
C
D
E
S
K39 C
Liftgate
Control
Module
5790 5791 3986 6127 3988 6000 3987 6126 5801 5797 3033
BN BU/GY GY GN/WH YE BU/BK VT/GN WH/BK BK/VT YE/OG GN/RD
B71L
Liftgate
Object
Sensor - Left 2
5797
2 BU
1
5802 S46 B70
GY/BK Liftgate Liftgate
Handle Switch Close Switch
7 8 4 3 1 5 2
1
A23C 2
Liftgate
M M Latch
Assembly B71R
Liftgate 5801
Object BU
Sensor -
6 Right
2 1
J903
B+ P16 L
P9 Instrument O
Driver Information Cluster C
X53A K171
64 Fuse Hands-Free Center Display
Block - Liftgate D
F14RA F25RA Rear Sensor E
10A 30A Body Control S
A90 C
36 22 Module Logic
840 7040
RD/BU RD/GY
TC2
X490 5 6
X900 29
840 7040
RD/BU RD/GY
TC2
X900 22 1
840 7040 5060 4118 5797
RD/BU RD/GY L-GN GN/BN YE/OG
X2 4 3 X1 7 15 10
K39
B+ B+ Liftgate
Control
Module
B+
X3 9 8 10 11 2 1 X1 1 12 X2 6
6112 6113
GN/BU GY/BK
X900 15 14
6112 6113
5805 5803 5806 5804 5799 5798 GN GY/BK
YE BN GN BU BK RD
3 4
M31 S45B
M Liftgate Motor Liftgate
Control 1450
634 1370 4120 BK
Switch -
3/4 Interior
OFF MAX
1050
BK
G210 G402
L
B+ O
C
X51R
Fuse Block - K39 D
F28DR Instrument Liftgate E
10A Panel Right Control S
C
Module
X1 43
3140
RD/GN
J403
3140
RD/GN
X495 22
3140
RD/GN
J492
3140 4118
RD/GN GN/BN
X1 2 1
K171
B+ Hands-Free
Liftgate
Sensor
Control
Module
X2 1 2 X1 3 X3 1 2
GN GN GN GN
B275A B275B
Hands-Free 1450 Hands-Free
Liftgate BK Liftgate
Sensor - Sensor -
Upper Lower
G402
P16
Instrument
Cluster
K9
Body
Control
Module
M33 A23C
Liftgate Liftgate
Window Latch Latch
Assembly Assembly
Manual Liftgate
The body control module supplies a 12V signal to the liftgate/liftglass ajar signal circuit. The liftgate and liftglass ajar switches are normally open when the liftgate or liftglass is fully closed. When the liftgate or liftglass is opened,
the ajar switch contacts close providing a path to ground. The instrument cluster receives a serial data message from the body control module indicating the liftgate ajar status and the driver information center will display the
REAR ACCESS OPEN message.
P16
Instrument
Cluster
K9 K39
Body Liftgate
Control Control
Module Module
M33 A23C
Liftgate Liftgate
Window Latch Latch
Assembly Assembly
Power Liftgate
The driver information center illuminates the Rear Access Open message when the liftgate module detects the liftgate ratchet and the liftgate sector switches are closed to ground indicating the liftgate is open. The instrument
cluster receives a serial data message from the liftgate module indicating the liftgate ajar status.
The body control module supplies a 12V signal to the liftglass ajar circuit. The liftglass ajar switch is normally open when the liftglass is fully closed. When the liftglass is opened, the ajar switch contacts close providing a path to
ground. The instrument cluster receives a serial data message from the body control module indicating the liftgate ajar status and the driver information center will display the REAR ACCESS OPEN message.
Operation
The power liftgate can be commanded to power open and power close by the following methods:
• An open or close request by a signal from the keyless entry transmitter to the remote control door lock receiver
• The kicking motion of a foot and lower leg under the rear fascia – Sensor location may vary depending upon make and model, refer to owner’s manual for the location of the sensors
The liftgate control module will respond to a request by commanding the liftgate latch to release the liftgate and activate the liftgate motor in the liftgate power assist actuator and raise the liftgate to the open position or to lower
and cinch the liftgate closed.
Power Latch
The liftgate control module continuously monitors power liftgate operation and calculates its location and direction of travel from an liftgate position sensor (part of the power assist actuator). One input returns the position of the
liftgate relative to the x-axis and y-axis. The liftgate control module then uses these 2 inputs together to calculate its angle relative to the liftgate. The interior liftgate rotary switch contains resistors which will incrementally drop
the voltage level in the signal circuit as the switch rotated from the OFF position to the ¾ position or the MAX position, the liftgate control module will detect the change in voltage and will monitor the x-axis and y-axis as the
liftgate is in motion to stop the liftgate parallel to the vehicle roof if the rotary switch is in the ¾ setting or to open fully if the rotary switch is in the MAX setting.
The liftgate latch assembly is a bi-directional motor and latch or unlatch operation is the result of the direction of the motor rotation. The liftgate control module controls the liftgate latch assembly through the control circuits by
supplying power and ground in the appropriate polarity. The motor control circuits are monitored by the liftgate control module prior to activation for a high or low condition and during motor operation for an insufficient current flow
condition. The ratchet, pawl, and sector switches are part of the liftgate latch assembly and are used by the liftgate control module to determine the state of the latch during the process of latching or unlatching. Each of the latch
switch signal circuits are supplied battery voltage and monitored within the liftgate control module. The latch switches share a common low reference circuit from the liftgate control module and when the switch contacts close the
signal circuit goes low and the liftgate control module determines the switch to be active.
The liftgate handle switch and liftgate close switch signal circuit are each supplied battery voltage by the liftgate control module. The switches share a common low reference circuit from the liftgate control module and when the
switch is pressed the contacts close and the appropriate signal circuit goes low, the liftgate control module will detect the voltage drop and will command the liftgate to release and power open or to power close.
For vehicles without the optional passive keyless entry, when the liftgate handle switch is pressed, the liftgate control module will check the status of the vehicle door locks by sending a serial data message to the body control
module requesting the door lock status. If the vehicle doors are locked, the liftgate control module will ignore the signal from the liftgate handle switch. If the vehicle doors are unlocked, the liftgate control module will permit the
liftgate to unlatch and power open when the liftgate handle switch is pressed.
For vehicles with the optional passive keyless entry system, the keyless entry control module monitors the proximity of the keyless entry transmitter. If the liftgate handle switch is pressed and the keyless entry transmitter is
within range, the keyless entry control module will send a serial data message to the liftgate control module indicating the presence of the keyless entry transmitter and the liftgate control module will permit the liftgate to unlatch
and power open. If the doors are locked and the keyless entry transmitter is not within range, the liftgate control module will ignore the signal from the liftgate handle switch.
Object Detection
The power liftgate system uses an object detection method which consists of object sensors fixed to both sides of the liftgate near the seal area. The object sensors consist of an internal fixed resistor and normally open switch
contacts which when closed will bypass the resistor. The signal circuit is supplied 5 V through a resistor and monitored within the liftgate control module, and during normal power liftgate operation the signal circuit should remain
a fixed value. When an object presses one of the sensors the contacts close and the resistor is bypassed causing the signal circuit voltage at the module to go low. If the liftgate is being power closed at that time, the liftgate
• Driver door key cylinder switch (Part of the driver door latch assembly)
• Right instrument panel fuse block (Contains child security lock disable PCB relay and/or door dead lock PCB relay)
• Pressing the driver door lock plunger flush with the door panel will lock all doors
S13D S13P
Door Lock Door Lock
Switch - Switch -
Driver Passenger
K9
Body
Control
Module
K84
Keyless
Entry
Control
Module
B272
Child
Security
Lock
Switch
K9
Body
Control
Module
A23LR A23RR
Door Door Latch
Latch Assembly -
Assembly Right Rear
- Left
Rear
The body control module will command the child lockout indicator to flash ON and OFF for the following reasons:
• The body control module detects that one or both rear door latches have not activated and are not locked out
• The body control module detects a short to ground or an open/high resistance in the child security lock disable relay control circuit
S46B P16
Liftgate Instrument
Unlatch Cluster
Switch
K9
Body
Control
Module
M30
Liftgate Latch
Liftgate Latch
When BCM receives a liftgate release command from the liftgate unlatch switch, the BCM applies voltage and ground to the liftgate unlatch relay control circuit, which energizes the coil side of the relay. The switch side of the
release relay then momentarily closes, supplying a brief pulse of battery positive voltage to the liftgate latch. The liftgate latch is continuously grounded and when it receives the voltage pulse, it will become energized and the
latch will activate releasing the liftgate so that it may be manually raised to an open position.
Liftgate Window
Liftgate Window Unlatch Switch
The BCM monitors supplies a 12 V signal to the liftgate window unlatch switch so that when the switch is pressed, the voltage within the signal circuit is pulled low and in response, the BCM will detect the voltage drop and check
the status of the door lock system. If the doors are locked, the BCM will ignore the request, if the All Doors Unlocked has been commanded, the BCM will recognize the request and command the liftgate window to release.
Rain Sense
L
B+ O
C
X51R
Fuse Block -
Instrument D
K9 E
F27DR Panel Right S
10A Body C
Control
Module
X1 42 15 X3 8 X3 23
840
RD/BU
840 7595
RD/BU GY/YE
X318 1
840 6132
RD/BU GN/BN
1 2 X3 4
B+ B200 S78
Rain Turn Signal/
Sensor Multifunction
Module Switch
1050
BK
G210
S78
B+ Turn Signal/Multifunction Switch L
O
P16 C
X51L Instrument
Fuse Block Cluster
F11DL - Instrument D
10A Panel Left A90 E
S
Logic C
332
X2 7
P9
Driver Information
Center Display
1070 825 665 536 442
X1 7 8 4 6
X1 24
X2 3 X3 10 13 20 25
K9
B+ Body
F19DL Control
F38DR Module
X4 16 X5 24 X4 14 17
X150 15
F114UA
15A
185
VT
X2 F2 X3 H2 X3 K4 K3 X1 G4 F2 1
150 228 B118B
550 550 92 95 Windshield
BK BK WH YE/BN BK GY/VT
L Washer
1 Fluid Level
G24 Switch
4 1 3 Windshield 2
M75 M Washer
Windshield Wiper Pump
M Motor 150
BK
2
5 2 150
BK
1850
BK/WH
L
B+ B+ O
C
X53A X50A
64 Fuse Fuse Block -
Block - Underhood D
KR6 E
F15RA Rear Rear S
Body C
20A Window
37 Washer
Pump
Relay
F115UA
15A
3040
RD/YE
K9
X490 7 Body X3 L3 X2 F2 X1 G4 D2
F11DL Control
Module
X2 12 X5 9
1
G19
Rear
X900 8 X201 5 M Window
Washer
Pump
2
391
3040 6135 BN/BU
RD/YE GN/GY
X3 1
3 2 S78
M45 Turn Signal/
B+ A90 Rear Multifunction
Logic Wiper Switch
Motor
1450 1851
BK BK/WH
• Rain Sensor
1. The BCM will initiate a single wipe by activating its front wiper ON/OFF relay output.
Intermittent wiper operation may be vehicle speed sensitive. When enabled, the speed compensated intermittent feature causes the intermittent wiper delay intervals to become shorter as a function of increased speed. As
vehicle speed is reduced the intervals will become closer to the predetermined
S78
Turn Signal/
Multifunction
Switch
K9
Body
Control
Module
M75
Windshield
Wiper Motor
P16
Instrument
Cluster
K9
Body
Control
Module
G24 B118B
Windshield Windshield
Washer Washer
Pump Fluid Level
Switch
B117
Rain
Sensor
K9
Body
Control
Module
Rear Wash
When the Body Control Module detects that the Rear wiper/wash switch has activated the momentary Wash switch, it activates a High Side Drive output which supplies Battery to the coil of the Rear Washer Pump Relay. This
energizes the Relay, which switches Battery Power to the Washer Pump Motor. The BCM will also activate continuous Low Speed Windshield Wipers as described above. The BCM software will attempt to detect a stuck Rear
Wash Switch. A stuck Rear Wash Switch condition is detected if the Rear Wash Motor Relay Output has been continuously active for 10 seconds or more. Upon detecting this the BCM will fail soft the state of the Rear Wash
Control to Inactive. This shall cause the System to perform as if the momentary Wash control had been released.
S78
Turn Signal/
Multifunction
Switch
K9
Body
Control
Module
X50A
Fuse Block -
Underhood
G19
Rear
Window
Washer
Pump
B+ L
O
C
X50A S91 P16
Fuse Block - Park P9 Instrument
Underhood Brake (UDD) PARK (-U19) Driver Information Cluster
F10UA D
Control P Center Display E
40A P (U19) S
Switch P
C
A90
Logic
X5 E1 1 7 4 5 3 2
X225 39 31 34 36 37 30
X185 14 9 10 12 13 11
1492 7684 6107 6108 7683 1134 5986 2500 2501 2500 2501
YE GY/RD BN BU/BK YE/RD BU/VT WH/BU BU WH BU WH
A N D R S B C P F L G K
K83
B+ 12V 5V 12V IGN Park
Brake
Control
Module
2150
BK
G121
P16
Instrument
Cluster
K83
Parking
Brake
Control
Module
S91
Park
Brake
Control
Switch
Vehicles with the electric parking brake have a switch in the center console, which takes the place of the manual parking brake system, the foot pedal and release handle. In case of insufficient electrical power, the electric
parking brake cannot be applied or released.
System Operation
Park brake apply input force is transferred and evenly distributed, through the park brake cables and the park brake cable equalizer, to the left and right park brake apply levers. The park brake apply levers multiply and transfer
the apply input force to the park brake actuators which expand the park brake shoe toward the friction surface of the drum-in-hat portion of the rear brake rotor in order to prevent the rotation of the rear tire and wheel assemblies.
The park brake lever/pedal assembly, if equipped, releases an applied park brake system when it is depressed again.
Trailer Brake
B+ L
O
X50A C
Fuse Block -
KR73 Underhood
Ignition Main Relay D
E
S
F23UA F36UA C
F74UA X88
15A 10A 30A
Trailer
Connector
C
X5 J5 G4 J2
242 47
RD/GN BU
1 8
Data K133
Communication B+ Trailer
Schematics 439 2040 Brake
VT/GN RD/WH Power
Control
Module
2 12 5 9
2500 2501 2500 2501 5985 2223 4114 2224 1750
BU WH BU WH VT/YE WH/BK GN/VT YE/BK BK
27 28 26 29 14 25 1 23 30 22
K38
IGN IGN B+ Chassis
Control
Module
5V
21 20 16 18 19 13
X185 1 3 4 5 6
7633 7635 7632 7634 7631 1750
GN/BK YE BU/RD BN BK/BN BK
Interior Lights X1 41 29 26 24 27
Dimming X61A
Schematics Junction
Block -
Instrument
X5 30 12 15 7 14 Panel
75 150 2k
2.2k 2.2k
G400
The Trailer Brake Control System is compatible with two types of Trailer Brake Systems as listed below:
1. Electric Brakes A controlled electrical output signal energizes an electric-magnet/lever arm assembly that directly actuates the brake mechanism. The GDS name for this system is “Electromagnetic Brakes”.
2. Electric Over Hydraulic Brakes A controlled electrical output signal energizes a remote, trailer mounted hydraulic pump to build brake pressure in a closed hydraulic system on the trailer. The hydraulic fluid pressure
actuates the brake mechanism. The GDS name for this system is “Electrohydraulic Brakes”.
• The trailer brake system characterizes the trailer brakes as either Electric Brake or Electric Over Hydraulic Brake automatically. This characterization may be affected by the number, type, and age of the trailer brake
magnets, as well as any other devices installed on the trailer brakes (i.e. adapters for Electric Over Hydraulic brake functionality).
• Some features of the trailer brake system may be different based on the trailer brake type characterization. An example of this is at zero speed, where pressing the service brake pedal will produce output when the trailer
brakes are characterized as Electric Brakes, but not when characterized as Electric Over Hydraulic Brakes.
• Sliding the manual trailer brake apply lever will produce output at zero speed for either characterization.
The user gain allows the driver to adjust the amount of trailer brake output to match the trailer load and road surface. The controller determines the desired trailer brake output and provides a control signal to the K133 Trailer
Brake Power Control Module. The K133 Trailer Brake Power Control Module amplifies the signal and provides the output required to activate the Electric or Electric Over Hydraulic trailer brakes.
The trailer brake control can support up to a maximum of four axles with electric trailer brakes (8 brake magnets).
Connecting a trailer that is not compatible with the trailer brake system may result in reduced or complete loss of trailer braking. There may be an increase in stopping distance or trailer instability which could result in personal
injury or damage to the vehicle, trailer or other property. An aftermarket controller may be available for use with trailers with surge or air trailer brake systems.
To determine the type of brakes on your trailer and the availability of controllers, check with your trailer manufacturer or dealer. Do not power up an aftermarket controller with the factory brake controller at the same time.
• Drive the tow vehicle and trailer combination on a level surface representative of the towing condition and free of traffic at approximately 32–40 km/h (20–25 mph) and fully apply the manual trailer brake apply lever
mechanism located on the trailer brake control panel switch. Adjusting the trailer gain at slower speeds may result in an incorrect gain setting.
• Adjust the trailer gain to just below the threshold of trailer wheel lock-up . Trailer wheel lock-up may not occur if towing a heavily loaded trailer. In this case, adjust the trailer gain to the highest allowable setting for the
towing condition.
Trailer Connected
This message will be briefly displayed when a trailer with Electric or Electric Over Hydraulic brakes is first connected to the vehicle. This message will automatically turn off in about ten seconds. The driver can also acknowledge
this message before it automatically turns off.
• The system detects that a trailer with Electric or Electric Over Hydraulic brakes is connected to the vehicle and then the trailer harness becomes disconnected from the vehicle.
• The trailer connection is recognized initially and then a disconnect occurs while the vehicle is stationary. This message will automatically turn off in about thirty seconds. This message will also turn off if the driver
acknowledges this message off or if the trailer harness is reconnected.
• A disconnect of the trailer wiring harness occurs while the vehicle is moving. The Check Trailer Wiring message will continue until the ignition is turned off. The message will also turn off if the driver acknowledges this
message off or it the trailer harness is re-connected or repairs are completed.
• There is an electrical fault in the wiring to the electric trailer brakes. The Check Trailer Wiring message will continue as long as there is an electrical fault in the trailer wiring. This message will also turn off if the driver
acknowledges this message off.
• A poor connection at the 7–way connector may cause the Check Trailer Wiring message. Some aftermarket 7–way trailer side connector adapters or plugs may cause deformation or excessive wear to the vehicle’s trailer
terminals. It is recommended that you use an OEM or Pollak heavy duty 7–way trailer side connector adapter.
1. Providing trailer braking when the master cylinder pressure or brake pedal switch are faulted.
2. Providing trailer braking when hill start assist and trailer sway control communication is faulted.
3. Providing trailer braking when certain manual trailer brake apply lever faults are present.
These conditions should be repaired to allow the trailer brake system to be fully functional.
L
B+ B+ O
C
X51R X51L
Fuse Fuse
D
F29DR Block - F39DL Block - E
20A Instrument 10A Instrument S
Panel Panel Left C
Right
X2 17 X2 35
340 2840
RD/VT RD/GY
J220
A90
B+ Logic
X3 BK X1 5 3 10
1102
GY/GN
340 7532
RD/VT LVDS GN/BU
X3 8 X7 BN X1 13 14 X2 1 2 3 4 7
A11
B+ D Radio
X3 16
2550
BK
G325
T4G T4M L
Cellular Radio O
Phone, Antenna C
Navigation,
and Digital
Radio D
1 2 E
Antenna S
U2K/U2M C
COAX
X4 CU 6002 3292
WH WH
T23
FM/RFR AM Radio
Antenna
Amplifier
AM/FM RFR
X1 BK X4 OG
Remote
Function
Schematics
X421 BK
COAX
X245 CU X221 BK
COAX COAX
X6 CU X4 BK
A11
Radio
HD/XM AM/FM
L
O
B+ C
X51R D
Fuse Block - E
Instrument S
F29DR C
20A Panel Right
X2 17
340
RD/VT
A11
Radio
J250
340
RD/VT
10 3 4 5 6 1
A33
B+ Media Disc
Player
2550
BK
G325
L
O
C
2 2 2 2 2 2 D
P19AG P19J P19AL P19AH P19W P19AM E
S
Speaker - Speaker - Speaker - Speaker - Speaker - Speaker - C
Left Front Left Left Rear Right Front Right Right
Door Instrument Door Door Instrument Rear Door
1 1 Panel 1 1 1 Panel 1
201 118 201 118 199 116 200 117 200 117 46 115
BU BN/BU BU BN/BU GN GN/BK YE YE/BK YE YE/BK WH BU/BK
9 9 9 9 9 9
X225 33 12
201 118 201 118 199 116 200 117 200 117 46 115
BU BN/BU BU BN/BU GN GN/BK YE YE/BK YE YE/BK WH BU/BK
9 9 9 9 9 9
X225 41 20 14 35
X275 41 20 14 35
-WX7 WX7 WX7 -WX7 -WX7 WX7 WX7 -WX7 -WX7 WX7 WX7 -WX7 -WX7 WX7 WX7 -WX7
X3 1 9 3 11 2 10 4 12
A11
Radio
A11
B+ Radio L
O
C
X51R
Fuse
F28DR Block - D
Instrument X8 X1 7 9 10 8 6 E
10A S
Panel C
Right
5842
BARE
X1 27
X300 42 X300 4 35 34 14 13
5842
BARE
5842
340 2060 5839 5841 5843 BARE
RD/VT USB BU GY GN VT
9
W7
Blunt Cut -
Shield
X1 6 X2 X1 5 1 2 3
X83
Auxiliary
SD Audio
Input
A90
Logic B+
X1 4
2550
BK
G325
A11 L
B+ Radio O
C
X51R
Fuse
F28DR Block - D
Instrument X8 X1 7 9 10 8 6 E
10A S
Panel C
Right
5842
BARE
X1 27
X238 X275 3 6 7 5 4
5842
BARE
5842
340 2060 5839 5841 5843 BARE
RD/VT USB BU GY GN VT
9
W7
Blunt Cut -
Shield
X1 6 X2 X1 5 1 2 3
X83
Auxiliary
SD Audio
Input
A90
Logic B+
X1 4
2550
BK
G325
L
O
C
B+
X51R D
Fuse Block - E
Instrument S
C
Panel Right
F29DR
20A
340
RD/VT
P17 T3
Info Audio
J250 Display Amplifier
Module
340
RD/VT
X3 8 X1 13 14 X2 1 2 3 4 7
A11
B+ Radio
X3 16
2250
BK
G325
B+ L
O
C
X51R
Fuse Block -
Instrument D
Panel Right E
S
C
F29DR F20DR
20A 10A
X2 17 1
1
Z75 S140
Media Disc
Eject
340 1540 1540 B+ Switch
RD/VT RD/GN RD/GN
J250 J212
4 6
T3 A11
Audio Radio Z75
Amplifier
U42
X1 10 3 4 5 6 1 (TG5) X1 9 (TG5)
X1 1 3 4 5 6 10 11 2 (U42)
A33
B+ Media Disc
Player
X1 7 (U42)
X1 8 (TG5)
2250 2050
BK BK
G325
B24 L
Mobile B+ B+
O
Telephone C
Microphone X51R X51L
Fuse Fuse
Block - Block - D
655 654 Instrument Instrument E
RD BK/BU Panel Panel Left S
F29DR F39DL C
B A 20A Right 10A
9
X2 17 X2 35
655 654
BU BK/BN 2840
RD/GY
X203 4 3 J220
9
X3 GY (X88/Z88) X1 3 5 10 (X88/Z88)
9 9
1792 X2 GY (Z75)
BARE X1 12 7 16 (Z75)
X1 1 2 7 X5 BU X2 9 8 2 3 1
K74
B+ D Human
Machine
Interface
Control
Module
X1 8
2550
BK
G325
T4G T4M L
Cellular Radio O
Phone, Antenna C
Navigation,
and Digital
Radio D
1 2 E
IO6+ (IO6+UE1+ U2K/U2M Antenna S
C
UE1-CV3 CV3)/(IO6-UE1)
COAX COAX
T23
FM/RFR AM Radio
UE1 -UE1
Antenna
X1 GY X1 GY Amplifier
AM/FM RFR
T15 T15
Navigation GPS/CELL GPS Navigation X1 BK X4 OG
Antenna Antenna
Signal Signal
Splitter GPS GPS/CELL GPS GPS Splitter COAX COAX COAX
X3 BU X2 VT X2 VT X3 BU
X245 CU (UE1)
COAX COAX COAX X245 1_BU 2_BU (-UE1) X421 BK Remote
Function
Schematics
OnStar/Telematics
Schematics
X221 BK
X7 BU X6 CU X4 BK
K74 A11
Human Radio
Machine
Interface
GPS Control HD/XM AM/FM
Module
B+ L
O
X51R C
Fuse Block -
F48DR Instrument D
30A Panel Right E
S
C
X1 37
3740
RD/YE
X1 4 X3 1 X4 3 4 5 6 14
T3
B+ Audio
Amplifier
X1 8
2250
BK
G325
L
O
C
D
E
S
C
2 2 2 2 2 2
P19AG P19J P19AL P19AH P19W P19AM
Speaker - Speaker - Speaker - Speaker - Speaker - Speaker -
Left Front Left Left Rear Right Front Right Right
Door Instrument Door Door Instrument Rear Door
1 1 Panel 1 1 1 Panel 1
201 118 201 118 199 116 200 117 200 117 46 115
BU BN/BU BU BN/BU GN GN/BK YE YE/BK YE YE/BK WH BU/BK
9 9 9 9 9 9
X225 33 12
201 118 201 118 199 116 200 117 200 117 46 115
BU BN/BU BU BN/BU GN GN/BK YE YE/BK YE YE/BK WH BU/BK
9 9 9 9 9 9
X225 41 20 14 35
X275 41 20 14 35
X3 1 9 3 11 2 10 4 12
A11
Radio
L
2 2 2 2 O
C
P19AG P19J P19W P19AH
Speaker - Speaker - Speaker - Speaker -
Left Front Left Right Right Front D
Door Instrument Instrument Door E
S
1 1 Panel 1 Panel 1 C
X2 7 15 X1 1 5 X2 6 14
346 315
J343 BU/GY GY/BK J346
J342 9 J347
X700 7 16 X800 7 16
346
199 116 BU/GY 46 115
GN GN/BK WH BU/BK
9 P19AC 9
Speaker -
Subwoofer
2 2 2 2
P19AN P19AL P19AM P19AP
Speaker - Speaker - 315 Speaker - Speaker -
Left Rear Left Rear GY/BK Right Rear Right Rear
Trim Panel Door Door Trim Panel
1 1 1 1
2
L
O
C
2 2 2 2 2
P19AG P19J P19B P19W P19AH
Speaker - Speaker - Speaker - Speaker - Speaker - D
E
Left Front Left Center Right Right Front S
Door Instrument Instrument Instrument Door C
1 1 Panel 1 Panel 1 Panel 1
201 118 1856 1956 1860 1960 1852 1952 200 117
BU BN/BU YE/BU YE/GY YE/WH BU/YE BN/GN VT/BN YE YE/BK
9 9 9 9 9
X1 1 (-D07) 5 (-D07)
X1 3 7 X2 5 13 10 2 4 12 X1 2 (D07) 6 (D07)
T3
Audio
Amplifier
X2 7 15 X1 1 5 X2 6 14 3 11
J462
D07 D07
J461
X700 7 16 X800 7 16
346
199 116 BU/GY 46 115 1859 1959 1859 1959
GN GN/BK WH BU/BK YE/BN WH/BK YE/BN WH/BK
9 P19AC 9 9 9
Speaker -
Subwoofer
2 2 2 2
P19AL P19AM P19AN P19AP
Speaker - 315 Speaker - Speaker - Speaker -
Left Rear GY/BK Right Rear Left Rear Right Rear
Door Door Trim Panel Trim Panel
1 1 1 1
2
L
O
C
2 2 2
P19J P19B P19W
Speaker - Speaker - Speaker - D
E
Left Center Right S
Instrument Instrument Instrument C
1 Panel 1 Panel 1 Panel
X275 31 10 22 1
X225 22 1
X2 5 13 10 2 4 12
T3
Audio
Amplifier
X1 1 5 X2 3 11
J462
J461
D07 D07
346
BU/GY 1859 1959 1859 1959
YE/BN WH/BK YE/BN WH/BK
P19AC 9 9
Speaker -
Subwoofer
2 2
P19AN P19AP
315 Speaker - Speaker -
GY/BK Left Rear Right Rear
Trim Panel Trim Panel
1 1
2
2 2 2 2 L
O
P19HD P19DD P19AG P19AH P19PD P19VD C
Speaker - Speaker - Left Speaker - Speaker - Speaker - Right Speaker -
Left Front Front Door Woofer Left Front Right Front Front Door Woofer Right Front
Door Door Door Door D
Tweeter 1 1 1 1 Tweeter E
S
118 1956 1952 117 C
201 1856 1852 200
BU BN/BU YE/BU YE/GY BN/GN VT/BN YE YE/BK
2 1 1 2
9 9 9 9
118 201 200 117
BN/BU BU YE YE/BK
9 9
X505 38 39 20 21 X605 20 21 38 39
X500 10 23 22 9 X600 22 9 23 10
X1 3 7 X2 9 1 X3 8 16 X1 2 6
T3
Audio
Amplifier
X2 7 15 6 14
X700 7 16 X800 7 16
199 116 46 115
GN GN/BK WH BU/BK
9 9
B+ L
O
X51R A11 C
Fuse Block - Radio
Instrument D
F29DR Panel Right E
20A S
C
X1 7 9 10 8 6
X2 17
340
RD/VT
2060 5839 5841 5843 5842
J250 BU GY GN VT BARE
9
340
RD/VT
X300 42 X300 4 35 34 14 13
340 340
RD/VT RD/VT
X1 6 X1 6 5 1 2 3
X92 X83
A90 USB A90 Auxiliary
B+ Logic Receptacle B+ Logic Audio
Input
SD
X1 4 X3 X2 X2 X1 4
2550 USB USB USB 2250
BK BK
X303
X302 BK (-U42)
X302 X_BK (U42)
USB USB
USB
X1 X4 X3
X92A K74
USB Human
Receptacle - Machine
Instrument Interface
Panel Control
Compartment Module
G325
A11 L
Radio O
B+ C
X51R
Fuse Block - D
F28DR Instrument X1 7 9 10 8 6 E
Panel Right S
10A C
X275 3 6 7 5 4
5842
BARE
X348 14 5 4 11 12 3
5842
BK
W7
X1 6 5 1 2 3 Blunt Cut -
Shield
X83
Auxiliary
A90 Audio
B+ Logic Input
SD
X1 4 X2
USB X92A
USB
Receptacle -
X304 Instrument
Panel
2250 Compartment
BK USB X1
X238
USB
USB
X3 X4
K74
Human
Machine
Interface
Control
Module
G325
T4G L
B+ Cellular O
Phone, C
X51R Navigation,
Fuse Block - and Digital
F26DR Instrument Radio D
Panel Right E
10A VV4 -CV3 CV3 CV3 Antenna S
C
COAX COAX COAX COAX
X2 34
X5 2_VT 1_VT X3 2_BU 1_BU
COAX COAX
COAX COAX
X222 2_PU X222 2_PU
T4S
Wireless X222 1_PU (-IO6) X222 1_PU (-IO6)
Communication X222 PU (IO6) X222 PU (IO6)
Antenna - Radio/
Bluetooth Navigation
(UPF) COAX COAX System COAX COAX
Schematics
X212 BN
COAX
X7 BN (VV4)
X1 15 X6 BG X5 PU X5 PU (-VV4) X7 BU X5 PU
K73
B+ Telematics
Communication
Interface
GPS Control Module
CELL 1 GPS/CELL (2) CELL
IGN
X1 7 1 10 12 X2 3 4 7
Data
Communication
Schematics
G325
B24
Mobile L
O
Telephone C
Microphone
655 654 D
E
RD BK/BN S
C
B A
655 654
BU BK/BN
X203 4 9 3
655 654
BU BK/BN
X2 9 10
K73
Telematics
Communication
Interface
Control Module
GN RD
10V
X1 3 2 6 11 X2 6 12 5 1 2 8
X316 25 26 24 22
4 5 1 3
S51 X1 20 19
1.5K 1.5K 10K Telematics A11
Button Radio
Assembly
6
1050
BK
G210
B24
Mobile L
Telephone O
C
Microphone
655 654 D
E
RD BK/BN S
C
B A
655 654
BU BK/BN
X203 4 3
9
655 654
BU BK/BN
X2 9 10
K73
Telematics
Communication
Interface
Control Module
GN RD
10V
X1 3 2 6 11 X2 6 12 5 1 2 8
5 X1 20 19
A11
Radio
1050
BK
G210
B24
Mobile L
O
Telephone C
Microphone
655 654 D
E
RD BK/BN S
C
B A
2 P50
Emergency
Call Backup 9
Speaker
655 654
1 BU BK/BN
X1 9 X2 11 X2 9 10
K73
Telematics
Communication
Interface
Control Module
GN RD
10V
X1 3 2 6 11 X2 6 12 5 1 2 8
X316 25 26 24 22
1.5K 11.5K
1050
BK
G210
Video Display - 2nd Row (U42) and 3rd Row (DNU) Power and Ground
L
O
C
B+
D
X51R A33 E
S
Fuse Block - Media Disc C
F20DR Instrument Player
10A Panel Right
D D
X2 1 X1 8 X4 WH X5 GY
1540 7066
RD/GN GN/YE LVDS
K74
Human
Machine
X204 WH D Interface
Control
X5 Module
X203 5 10
X88/Z88
LVDS
DNU DNU DNU
X2
K188
D Human
Machine
Interface
1540 7066 1540 7066 Control
RD/GN GN/YE LVDS RD/GN GN/YE LVDS LVDS D Module
Bypass
X3 Module
LVDS
X2 10 9 X1 BK
P22B X88/Z88
B+ D Video
Display -
3rd Row
X2 8 (ULT) 20 (ULT)
X2 8
X2 10 (-ULT) 9 (-ULT) X1 BK
P22A (Z75) X2 GY
B+ D Video (X88/Z88) X3 BK
Display - P17
2nd Row D Info
2250 Display
BK Module
X2 1 9 2 10 13 3 11 4 12 14 19 (ULT)
X2 8 (-ULT)
ULT ULT ULT ULT ULT ULT ULT ULT ULT ULT 2250
BK
7262 7263 7260 7261 7264 7267 7268 7265 7266 7269
WH/GN BN/WH WH/VT BN BARE WH/BN BN/BU WH/BU BN/GY BARE
X366 1 2 3 4 5 6 7 8 9 10
G325
L
O
C
B+ X1 6
X82 D
X51R VIDEO Audio/ E
Video S
Fuse Block - SD C
Instrument Input
F29DR Adapter
20A Panel Right
A90
B+ Logic
X2 17
D
340
RD/VT
J250
X1 4 X2 BK X3 X1 1 3 2
340
RD/VT
X300 24
W7
Blunt Cut -
LVDS Shield
16 38 37 17
LVDS
X3 BK X5 X2 1 3 2 4
A33
D Media Disc
Player
G325
X51L
Fuse Block B+ L
KR76A O
- Instrument C
Retained Accessory Power Panel Left X51R A19D
Relay 1 Fuse Block - DVD
Instrument Player - D
F36DR Panel Right Driver E
30A Seat S
C
F8DL Headrest
10A IGN
T4U
X2 38 Auxiliary X1 6 5 4 3 2 1 X2 6 5 4 3 2 1
Audio
Transmitter
X1 44 Antenna
43 2340 RD BK WH RD YE BK RD BK WH RD YE BK
VT/YE RD/YE
X2 50 X4 31 X371 1 2 3 4 5 6 X373 1 2 3 4 5 6
X61A
Junction
Block -
Instrument BK BK RD BK WH RD YE BK RD BK WH RD YE BK
Panel
X7 8 7
YE RD
X1 3 X6 1 2 X2 6 5 4 3 2 1 X3 6 5 4 3 2 1
X55X K13
Fuse IGN IGN DVD
X 5A Holder - Control
Video Module
Y Display
IGN
RD X1 1 X4 6 5 4 3 2 1 X5 6 5 4 3 2 1
C2 A2
KR103 RD BK WH RD YE BK RD BK WH RD YE BK
DVD Relay
A1 C1 X374 1 2 3 4 5 6 X372 1 2 3 4 5 6
BK PU BK RD BK WH RD YE BK RD BK WH RD YE BK
J387
X1 6 5 4 3 2 1 X2 6 5 4 3 2 1
A19P
IGN DVD
1050
BK Player -
Passenger
Seat
Headrest
G210
• Microphone
• Cellular antenna
• Navigation antenna
• TTY (Teletypewriter)
This system also interfaces with the factory installed vehicle audio system.
T4S
Wireless
Communication
Antenna -
Bluetooth
K73
Telematics
Communication
Interface
Control Module
A11 X84
Radio Data Link
Connector
• The OnStar® button assembly may be part of the rearview mirror, or a separate, stand alone unit. The button assembly is comprised of 3 buttons or 3 capacitive touch buttons and status LED’s or an error indicator. The
buttons are defined as follows:
– The answer/end button, which is black with a white phone icon or a white driver figure seated with voice signals near its face, allows the user to answer and end calls or initiate speech recognition.
– The blue OnStar® call center button, which displays the OnStar® logo, allows the user to connect to the OnStar® call center.
– The emergency button, which displays white letters “SOS” with red background, sends a high priority emergency call to the OnStar® call center when pressed.
If the LED does not illuminate, this may indicate that the customers OnStar® subscription is not active or has expired. Push the blue OnStar button to connect to an advisor who can then verify the account status.
The telematics communication interface control module supplies 10 volts to the OnStar® button assembly on the keypad supply voltage circuit. When pressed, each button completes a circuit across a resistor allowing a specific
voltage to be returned to the telematics communication interface control module on the keypad signal circuit. Depending upon the voltage range returned the telematics communication interface control module is able to identify
which button has been pressed.
The OnStar® status LED or error indicator is located near the buttons. The LED is green when the system is ON and operating normally. When any indicator is illuminated and flashing, it is an indication that a call is in progress.
When the LED is red, this indicates a system malfunction is present. In the event there is a system malfunction and the OnStar® system is still able to make a call, the LED will flash red during the call.
Each LED or error indicator is controlled by either the telematics communication interface control module over dedicated LED signal circuits or by low speed GM LAN serial data depending on the inside rearview mirror option.
Ground for the LED is provided by the wiring harness attached to the button assembly.
OnStar® Microphone
The cellular microphone can be part of the rearview mirror assembly, or a stand-alone unit in the headliner or roof console. In either case, the telematics communication interface control module supplies approximately 10V to the
microphone on the cellular microphone signal circuit. The microphone modifies the 10V depending on the volume and voice being detected. A cellular microphone low reference circuit or a drain wire provides a ground for the
microphone. The microphone signal circuits pass through the telematics communication interface control module to support entertainment voice recognition.
• GPS element
• AM/FM element
The Gen 10 OnStar® system uses 2 cellular antenna elements to send and receive cellular data, the primary cellular element and the secondary cellular element. The primary cellular signal is carried by a coax cable that
connects the antenna directly to the telematics communication interface control module. Details of the secondary cellular signal are further described below.
The GPS antenna element is used to collect the signals of the orbiting GPS satellites. Within the antenna is housed a low noise amplifier that allows for a more broad and precise reception of this data. Also housed within the
antenna is circuitry to combine the GPS signal and the secondary cellular signal. Without navigation, the combination GPS/secondary cellular signal is carried by a coax cable that connects directly to the telematics
communication interface control module. The cable also provides a path for DC current for powering the antenna. With navigation, the combination GPS/secondary cellular signal is carried by a coax cable that connects to the
navigation signal splitter. The splitter supplies the GPS signal to the navigation/entertainment system and the GPS/cellular signal to the telematics communication interface control module.
The digital radio element collects digital radio signals from two satellites and where necessary terrestrial repeaters. The digital radio signal is carried by a coax cable and connected to the digital radio receiver. Refer to
Radio/Audio System Description and Operation for further details.
The radio signal is sent from a broadcast station and is then received by the AM/FM radio antenna element. The AM/FM radio signal is carried by a coax cable and is connected to the radio. Refer to Radio/Audio System
Description and Operation for further details.
OnStar® RemoteLink
OnStar® RemoteLink is a mobile app to link mobile devices to a vehicle for limited diagnostics and feature controls. After downloading the app and registering the device, vehicle owners with an eligible vehicle can use their
mobile devices to access real-time data from their vehicle and perform specific commands remotely.
All communication between the app and the vehicle is powered by OnStar's® advanced connected vehicle technology. An active OnStar® account as well as a valid OnStar® username and password are required to use the app.
The remote commands must be enabled by logging into the user’s OnStar® account prior to using the app. Refer to the owners manual for available vehicle data and control features.
• Automatic reconnection – highest priority phone will automatically be connected to vehicle when vehicle ignition is on
• Hands-free dialing- via digits, redial, name tags (phone number saved to a nametag via voice recognition)
• Answering a call
• Ending a call
• Mute a Call
• Call Waiting
• Send Number During a Call – this is used when calling a menu-driven phone system
• Transfer a Call – transfer call from vehicle to cellular phone and visa versa
• Voice Pass-Thru – allow access to the voice recognition commands on the cellular phone
The back-up battery is intended to have a limited life span of approximately 4 years and is designed to maintain an open circuit voltage between 16 V and 9 V throughout this period. This allows the battery to power the basic
functions of the telematics communication interface control module for least one 200 second (5 minute) call at the end of the 4 year span, should the main vehicle battery be lost. In the case of a vehicle losing vehicle battery
power, OnStar will switch over to the backup battery based on an internal algorithm. It will look for an air-bag deploy, or near-deploy, messages from the SDM. If there are no messages the OnStar module will stay wake for a
few minutes longer and monitor the buttons in the mirror. If not pressed, the modules will power down and shut off completely.
The back-up battery is connected to the telematics communication interface control module through the back-up battery positive voltage circuit and back-up battery ground circuit and is protected from a short circuit by means of
an internal fuse. In the event the back-up battery, battery positive voltage circuit is shorted to the back-up battery ground circuit or chassis ground, the fuse will open and render the back-up battery permanently inoperable. The
status of the back-up battery and its associated wiring is monitored by the telematics communication interface control module.
WiFi Hotspot
The telematics communication interface control module acts as a Wireless Local Area Network (WLAN) WiFi hotspot router and uses direct 4G LTE connectivity to the internet. It has the ability to connect up to 7 devices at one
time. A data plan is required and when purchased, a security default password is established. There are several ways to change the SSID or password, by placing a call to the OnStar Call Center, by using the Gen 10 mobile app
• High power
• Low power
• Sleep
• Digital standby
The high power state is in effect whenever the ignition is in the ON or RUN position, or retained accessory power is enabled, and the OnStar® system is sending or receiving calls or when the system is performing a remote
function.
The low power state is in effect when the OnStar® system is idle with the ignition in the ON or RUN position, or with retained accessory power enabled.
The sleep state is entered after the vehicle has been shut off and the retained accessory power has timed out while in an analog cellular area. At a predetermined time recorded within the telematics communication interface
control module, the system re-enters the low power state to listen for a call from the OnStar® Call Center for 1 minute. After this interval, the system will again return to the sleep state for 9 minutes. If a call is sent during the 1
minute interval, the OnStar® system will receive the call and immediately go into the high power mode to perform any requested functions. If no call is received during the 1 minute interval, the system will go back into the sleep
mode for another 9 minutes. This process will continue for up to 48 hours, after which the OnStar® system will turn off until the ignition is turned to the ON or RUN position.
The digital standby power state is entered after the vehicle has been shut off and the retained accessory power has timed out while in a digital cellular area. When in digital standby mode, the OnStar® module is able to perform
all remote functions as commanded by an OnStar® advisor at any time, for a continuous 120 hours. After 120 hours, the OnStar® module will go into sleep mode until a wake up signal from the vehicle is seen by the telematics
communication interface control module. If the OnStar module loses the digital cellular signal it will revert to analog mode and follow the standard sleep state (9 minutes OFF, 1 minute standby) based on the time of the GPS
signals, this will continue until a digital cellular signal is again received.
If the OnStar® system loses battery power while the system is in a standby or sleep mode, the system will remain OFF until battery power is restored and the ignition is turned to the ON or RUN position.
Features
OnStar® Personal Calling
The hands free, OnStar® personal calling cellular phone feature is an additional feature of the OnStar® system. This feature is embedded within the telematics communication interface control module; however it must be
activated by an OnStar® advisor. OnStar® personal calling operates similar to most hand held cellular phones in that the availability for its usage is based on minutes or units. The customer must have a current OnStar®
subscription, as this feature cannot be utilized without it. To use OnStar® personal calling, the customer must also purchase units (minutes) as outlined in the owners guide provided with the OnStar® system. Units begin to
deplete, 1 unit is equal to 1 minute, as the customer makes outbound phone calls, answers inbound phone calls, or while connected to the OnStar® virtual advisor. In addition, units may also have an expiration date, depending
upon the type of units purchased.
Customers have the ability to store telephone numbers within the module, referenced by a nametag for the convenience of frequently dialed numbers. After storing a nametag, the user can dial this number by initiating the
OnStar® personal calling feature, speaking the word "call," and repeating the nametag assigned.
• The OnStar® system will NOT attempt to connect to the OnStar® Call Center in the event of a collision or if the vehicle's front air bags deploy for any other reason.
• An emergency button press will play a demo message indicating the service has been deactivated.
• An OnStar® Call Center button press will connect the customer with a dedicated sales team who can sell an OnStar® subscription and reactivate the vehicle. Depending on the type of OnStar® hardware in the vehicle,
• OnStar® personal calling will not be available, as this feature requires the customer to have a current OnStar® account. Attempts to use this feature may result in cellular connection failure messages and the inability to
connect to the number dialed.
Certain vehicles that have never had an active OnStar® account, or that have been deactivated, may be unable to establish a connection with the OnStar® Call Center. When normal published diagnostic procedures do not
indicate a possible cause for the no connect concern, the vehicle may have been deactivated. For deactivated vehicles, a no connect response should be considered normal operation. Further diagnosis and subsequent repair is
only necessary should the customer elect to become an active OnStar® subscriber or renew the account subscription.
• Personal Calling uses a speech recognition system that resides in the vehicle. When the user presses the phone button, the system states, Ready, and listens for the user's command. The user can speak commands to
control the hands-free phone.
• Virtual advisor is a remote speech recognition system that the caller can access by making a phone call. The user connects to virtual advisor by requesting it during personal calling use. The user is then transferred to the
virtual advisor server and talks to it via a cellular connection.
The OnStar® speech recognition systems use speech technology that is designed to understand a wide range of American English speakers. Although there is no one right way to speak English, the system will work best when
users try to modify their pronunciation should they encounter difficulty. Users who do not obtain good results are advised to try the tips and workarounds found in the Infotainment System Manual or the Owners Manual.
• Microphone
• Cellular antenna
• GPS antenna
• Back up battery
• Backup speaker
This system also interfaces with the factory installed vehicle audio system.
The two button assembly may be part of the rear view mirror, or a separate, stand alone unit. The button assembly is comprised of 2 buttons and one status LED. The buttons are defined as follows:
– The “SOS” button, when pressed allows the user to start a manual emergency call.
– The TEST button, which has two functions. First it allows the user to cancel an emergency call before the call has been established with the call center. Second, if pressed longer than 4 seconds allows the user to enter
the system test mode.
When pressed, each button completes a circuit across a resistor allowing a specific voltage to be returned to the telematics communication interface control module on the keypad signal circuit. Depending on the voltage range
returned the module is able to identify which button has been pressed.
The status LED is located near the buttons on the button assembly. The LED is green when the system is ON and operating normally. When the LED is red, this indicates a system malfunction is present. When the LED is
illuminated and flashing, it is an indication that a call is in progress. In the event there is a malfunction and the system is still able to make a call, the LED will flash red during the call however, the call functionally might be limited
related to the issue that is present. During night mode the module provides a PWM signal to dim the brightness of the LED.
When the “SOS” button is pressed the LED will start blinking green and a voice prompt will instruct the customer to either press the “SOS” button again to continue with the emergency call, or press the “TEST” button to cancel. If
the user does not press either of the buttons in a certain amount of time the module will go back into standby mode and inform the customer via a voice prompt.
In the case of a callback from the call center the LED will be solid red or green. A solid red LED indicates an emergency call related DTC has been set by the telematics communication interface control module, otherwise the
LED will be solid green.
After a call to the call center the module will stay in callback mode for 20 minutes with the ignition ON of OFF and the LED will be on solid during this time. After 20 minutes there will be a voice prompt and the LED will turn off.
After that the module will stay registered to the network for an additional 100 minutes.
Microphone
The microphone is located in the headliner or roof console. The telematics communication interface control module supplies approximately 10V to the microphone on the microphone signal circuit. The microphone modifies the
10V depending on the volume and voice being detected. A microphone low reference circuit or a drain wire provides a ground for the microphone. The microphone signal circuits pass through the telematics communication
interface control module to support entertainment voice recognition. Thus, the module uses the same microphone as the infotainment system. In the event the infotainment system uses two microphones only one will pass
through the telematics communication interface control module.
• GPS/Glonass element
The ERA Glonass system uses the input and output cellular antenna elements to send and receive cellular data. The cellular signal is carried by a coax cable that connects the antenna directly to the telematics communication
Back-up Battery
Note: Do not disconnect the main vehicle battery or remove the telematics fuse with the ignition key in any position other than OFF. Disconnecting power to the telematics communication interface control module in any way
while the ignition is ON or with retained accessory power activated may cause activation of the Back-Up Battery. This action is per design as the back-up battery is designed to provide power to the telematics communication
interface control module so an emergency notification call can be made after an event where the main battery is disabled or unable to supply sufficient voltage to drive the module. The telematics communication interface
control module naturally chooses the main supply voltage as it’s default supply. If an emergency call is active, or the network de-registration timer has not expired, and the main supply is removed or lost for any reason the
module will use the Back-Up Battery as a power supply to continue the emergency call as long as the default supply can not be detected . If the module is in standby mode and the vehicle battery is disconnected the module
will switch to the backup battery for three seconds. If there is no collision event or emergency button press within the three seconds the module will switch off to prevent damage to the backup battery. The back-up battery is
not rechargeable and must be replaced if the diagnostics for the DTC (Replace Backup Power Source) indicate it is needed.
• Data Communications
• Speaker Operation
• Antenna System
• Radio Reception
• Theft Deterrent
• Valet Mode
• OnStar ®
Data Communications
The infotainment system communicates with other devices on multiple serial data networks during operation. The infotainment system utilizes the Media Oriented Systems Transport (MOST) bus, Local Interconnect Network
(LIN) and GMLAN to establish communications. For additional information refer to Data Link Communications Description and Operation
Radio Power
The radio receives battery power and ground from the vehicle harness.
The radio does not use a discrete ignition feed circuit for power moding. The power mode master provides the system power mode to the radio via serial data messages. The power mode master determines the system power
mode by processing power mode information from ignition switch inputs. Serial data power modes supported by the radio are OFF, ACCESSORY, RUN, and CRANK REQUEST.
Amplifier Operation
The purpose of the amplifier is to increase the power of a voltage or current signal. The output signal of an amplifier may consist of the same frequencies as the input signal or it may consist of only a portion of the frequencies as
in the case of a subwoofer or midrange speaker. The audio amplifier amplifies the signal and sends it to the appropriate speakers.
Each of the audio output channel circuits (+) and (−), at the audio amplifier have a DC bias voltage that is approximately one half of the battery voltage. When using a DMM, each of the audio output channel circuits will measure
approximately 6.5V DC. The audio being played on the system is produced by a varying AC voltage that is centered around the DC bias voltage on the same circuit. The AC voltage is what causes the speaker cone to move and
produce sound. Both the DC bias voltage and the AC voltage signals are needed for the audio system to properly produce sound.
The audio amplifier is also responsible for operation of active noise cancellation. Refer to CELL Link Error - Link target cell (cell ID 194567) is invalid for this publication. for more information.
Speaker Operation
Speakers turn electrical energy into mechanical energy to move air, using a permanent magnet and an electromagnet. The electromagnet is energized when the radio or amplifier (if equipped) delivers current to the voice coil on
• Diagnostic information
The radio sends the display digital video data for on-screen display through a dedicated video cable.
HVAC data for controls and status indicators is communicated between the HVAC controls and the HVAC control module with a separate LIN serial data circuit. HVAC status screen information from the HVAC control module is
transmitted to the radio on the GMLAN serial data circuit.
Antenna System
Active Antenna
The active antenna system uses an integral antenna applied as an appliqué to the rear glass. The antenna amplifier receives both AM and FM signals from the rear glass antenna. The antenna is part of the rear window and looks
similar to the defogger grid. One antenna receives AM signals while the other antenna receives FM signals. Any damage to the antenna requires replacing the glass.
The radio antenna amplifier is enabled when the radio is turned on. The radio provides battery voltage to the antenna amplifier using the center conductor of the antenna coaxial cable. When a 12 V signal is seen by the amplifier
on the center conductor of the antenna coax, the received signals are amplified.
Multi-Band Antenna
The multi-band antenna is located on the roof of the vehicle. This type of antenna may be used with the AM/FM radio, but is primarily for cellular, GPS signals, and XM signals, if the vehicle has these features. Keep this antenna
clear of snow and ice build up for clear reception. If the vehicle has a sunroof, the performance of the system may be affected if the sunroof is open. Loading items onto the roof of the vehicle can interfere with the performance of
the system, ensure the multi-band antenna is not obstructed.
Radio Reception
AM/FM Radio Signal
The radio signal is sent from a broadcast station and is then received by an antenna. The strength of the signal received depends on the following:
• The location of the vehicle (or receiver) relative to the broadcast tower.
• Atmospheric conditions
• Display text information such as: station identification, type of programming, and general information (artist and song title, station messages, call in phone numbers, etc.).
Theft Deterrent
The radio theft deterrent system is intended to disable or limit radio functionality if incorrect vehicle information is received by the radio. The radio disables functionality if the VIN information received by the radio does not match
the VIN information that has been learned by the radio. The radio receives this information via serial data. A possible cause of incorrect VIN info could be the radio was originally installed in another vehicle.
The radio has the following theft operating modes as part of the theft deterrent system:
• Normal Mode: The radio has learned a correct VIN sequence and the VIN information received via serial data matches the learned VIN sequence. In this mode the radio has full functionality.
• No VIN Mode: The radio has not received or learned a correct VIN sequence. In this mode the radio has limited functionality.
• Theft Detected Mode: The radio has learned a correct VIN sequence and the VIN information received via serial data does NOT match the learned VIN sequence. In this mode the radio may be disabled or have limited
functionality. The radio display will indicate that theft protection is active.
• When a device is first connected to the 3.5mm (1/8 in.) input jack the infotainment system automatically switches to that device. If an auxiliary device has already been connected, press the AUX or CD/AUX button to
select the device.
• Playback of an audio device that is connected to the 3.5mm jack can only be controlled using the controls on the device.
• The volume control on the device may need to be adjusted to ensure sufficient playback volume through the infotainment system.
USB Port
The USB port allows connectivity to the infotainment system from portable media players or a USB storage device (memory stick/ flash drive). When a device is connected to the USB port, the system detects the device and
switches to USB as the audio source. Once connected, the device can be controlled from the radio controls.
Not all portable media player devices or file types are compatible. Connection to USB HUB devices is not supported.
Refer to the owner’s manual for information on USB devices, control, and operation.
SD Card Reader
The infotainment system uses the SD card reader as a mass storage device, similar to a USB storage device.
Refer to the owners manual for information on media types supported via the SD card reader.
Valet Mode
Valet Mode is a customer enabled feature of the infotainment system, found in the settings menu, if equipped. The customer creates and inputs a four digit code using the infotainment controls. Confirming the code and selecting
LOCK will lock the infotainment system, steering wheel controls and other vehicle features, dependant on vehicle equipment. The vehicle will remain in valet mode until the same four digit code is reentered.
In the event that the four digit code is forgotten, the scan tool can be used to clear the Valet Mode Code.
• Data Communications
• Speaker Operation
• Antenna System
• Radio Reception
• Theft Deterrent
• Valet Mode
• OnStar ®
Data Communications
The infotainment system communicates with other devices on multiple serial data networks during operation. The infotainment system utilizes the Media Oriented Systems Transport (MOST) bus, Local Interconnect Network
(LIN) and GMLAN to establish communications. For additional information refer to Data Link Communications Description and Operation
Radio Power
The radio receives battery power and ground from the vehicle harness.
The radio does not use a discrete ignition feed circuit for power moding. The power mode master provides the system power mode to the radio via serial data messages. The power mode master determines the system power
mode by processing power mode information from ignition switch inputs. Serial data power modes supported by the radio are OFF, ACCESSORY, RUN, and CRANK REQUEST.
Speaker Operation
Speakers turn electrical energy into mechanical energy to move air, using a permanent magnet and an electromagnet. The electromagnet is energized when the radio or amplifier (if equipped) delivers current to the voice coil on
the speaker. The voice coil will form a north and south pole that will cause the voice coil and the speaker cone to move in relation to the permanent magnet. The current delivered to the speaker is rapidly changing alternating
current (A/C). This causes the speaker cone to move in two directions producing sound.
• Diagnostic information
HVAC data for controls and status indicators is communicated between the HVAC controls and the HVAC control module with a separate LIN serial data circuit. HVAC status screen information from the HVAC control module is
transmitted to the radio on the GMLAN serial data circuit. The radio communicates the desired screen information to the human machine interface module to be sent to the information display using the video data circuits.
Antenna System
Active Antenna
The active antenna system uses an integral antenna applied as an appliqué to the rear glass. The antenna amplifier receives both AM and FM signals from the rear glass antenna. The antenna is part of the rear window and looks
similar to the defogger grid. One antenna receives AM signals while the other antenna receives FM signals. Any damage to the antenna requires replacing the glass.
The radio antenna amplifier is enabled when the radio is turned on. The radio provides battery voltage to the antenna amplifier using the center conductor of the antenna coaxial cable. When a 12 V signal is seen by the amplifier
on the center conductor of the antenna coax, the received signals are amplified.
Multi-Band Antenna
The multi-band antenna is located on the roof of the vehicle. This type of antenna may be used with the AM/FM radio, but is primarily for cellular, GPS signals, and XM signals, if the vehicle has these features. Keep this antenna
clear of snow and ice build up for clear reception. If the vehicle has a sunroof, the performance of the system may be affected if the sunroof is open. Loading items onto the roof of the vehicle can interfere with the performance of
the system, ensure the multi-band antenna is not obstructed.
Radio Reception
AM/FM Radio Signal
The radio signal is sent from a broadcast station and is then received by an antenna. The strength of the signal received depends on the following:
• The location of the vehicle (or receiver) relative to the broadcast tower.
• Atmospheric conditions
• Display text information such as: station identification, type of programming, and general information (artist and song title, station messages, call in phone numbers, etc.).
• Receive alert warnings of local or national emergencies. When an alert announcement comes on the current radio station, ALERT! displays. You will hear the announcement, even if the volume is low or a CD is playing. If
a CD is playing, play stops during the announcement. Alert announcements cannot be turned off. ALERT! is not affected by tests of the emergency broadcast system. This feature is not supported by all RDS stations.
Theft Deterrent
The radio theft deterrent system is intended to disable or limit radio functionality if incorrect vehicle information is received by the radio. The radio disables functionality if the VIN information received by the radio does not match
the VIN information that has been learned by the radio. The radio receives this information via serial data. A possible cause of incorrect VIN info could be the radio was originally installed in another vehicle.
The radio has the following theft operating modes as part of the theft deterrent system:
• Normal Mode: The radio has learned a correct VIN sequence and the VIN information received via serial data matches the learned VIN sequence. In this mode the radio has full functionality.
• No VIN Mode: The radio has not received or learned a correct VIN sequence. In this mode the radio has limited functionality.
• Theft Detected Mode: The radio has learned a correct VIN sequence and the VIN information received via serial data does NOT match the learned VIN sequence. In this mode the radio may be disabled or have limited
functionality. The radio display will indicate that theft protection is active.
• The device must be paired to the system to use the available Bluetooth ® feature(s). The pairing process must only be performed once for each device, unless that device’s information is deleted.
• Up to five devices can be paired, but only one can be connected at any given time.
• Streaming Audio allows playing music from the mobile device wirelessly. Music stored on the mobile device can be viewed and controlled from the display.
• To stream audio from a mobile device, the device must be unlocked, and any additional applications should be closed.
Refer to the vehicle owners manual, supplements, and the device manufacturers information for pairing instructions.
• For an application to be used, it must be installed on both the vehicle infotainment system and a compatible mobile device.
• The device must be connected to the system. this may be done wirelessly via Bluetooth ®, or via the vehicle USB port. Refer to the device manufacturers information for the proper connection method.
• When the device is connected, the vehicle infotainment system is used to remotely access and control the application on the mobile device.
• The application must work correctly on the device to work with the vehicle infotainment system.
• The user may be required to log-in to the application on the mobile device before using the application from the vehicle controls.
• The device must be unlocked, and any additional applications should be closed.
Refer to the owner’s manual and supplements for information on mobile devices, control, and operation.
• When a device is first connected to the 3.5mm (1/8 in.) input jack the infotainment system automatically switches to that device. If an auxiliary device has already been connected, press the AUX or CD/AUX button to
select the device.
• Playback of an audio device that is connected to the 3.5mm jack can only be controlled using the controls on the device.
• The volume control on the device may need to be adjusted to ensure sufficient playback volume through the infotainment system.
USB Port
The USB port allows connectivity to the infotainment system from portable media players or a USB storage device (memory stick/ flash drive). When a device is connected to the USB port, the system detects the device and
switches to USB as the audio source. Once connected, the device can be controlled from the radio controls.
Not all portable media player devices or file types are compatible. Connection to USB HUB devices is not supported.
Refer to the owner’s manual for information on USB devices, control, and operation.
SD Card Reader
The infotainment system uses the SD card reader as a mass storage device, similar to a USB storage device.
Refer to the owners manual for information on media types supported via the SD card reader.
• Connection to the global positioning system (GPS) antenna, which provides the vehicle position information.
• Map data for navigation and map route guidance, stored in the human machine interface modules internal memory.
• Traffic and weather information for display on the navigation system map (with active subscription, where available).
Route Guidance
The map will display the route to the selected destination. Voice prompts alert the operator of upcoming events (turns) and arrivals at the destination. The navigation system will automatically recalculate if the route is not
followed. The human machine interface module uses data received from the global positioning system (GPS) satellites, the vehicle speed signal. and serial data information to accurately display the current position of the vehicle.
Points of Interest
The map database provides point of interest information. Points of interests are locations that are frequently visited. Points of interest can be can be displayed on the map or set as a destination. The following are some of the
available Points of interests:
• Gas Station
• Restaurant
• College
• Police Station
Valet Mode
Valet Mode is a customer enabled feature of the infotainment system, found in the settings menu, if equipped. The customer creates and inputs a four digit code using the infotainment controls. Confirming the code and selecting
LOCK will lock the infotainment system, steering wheel controls and other vehicle features, dependant on vehicle equipment. The vehicle will remain in valet mode until the same four digit code is reentered.
In the event that the four digit code is forgotten, the scan tool can be used to clear the Valet Mode Code.
• Remote Control
• Wireless Headphones
• Auxiliary Inputs
Rear Display
The 2nd row overhead display is located in the headliner. The display screen shows video from the media disc player, or an AUX input device.
The display receives power and ground from the vehicle harness. A discrete control circuit from the media disc player is used to control the power state of the display. The display receives all other video, audio, and control
information via the LVDS cable.
The display contains the infrared transmitters for the wireless headphones and the remote control. During operation, the infrared transmitters may be visible as illuminated LEDs.
Remote Control
The wireless remote control is used to operate the system from the rear seat. Infrared signals from the remote control are received by the infrared receivers in display. The remote control can be used to turn the rear screen on or
off, to change system settings, and to select the source for the screen from the media available to the infotainment system. Refer to the Owners Manual for additional information on remote control functions.
Direct sunlight or very bright light may affect the ability of the infrared receivers to respond to signals from the remote control. Objects blocking the line of sight may also affect the function of the remote control.
Wireless Headphones
Wireless headphones allow for rear seat passengers to listen to an audio source without disturbing the listening of front seat passengers. The wireless headphones receive audio signals from the infrared transmitter in the display.
This transmission is line of sight only, so audio quality may be degraded if anything blocks the transmitter signal from reaching the headphones.
A power button on the headphone is used to turn the headphone on. A red LED illuminates when the headphone is turned ON. The headphones automatically turn OFF if they lose the infrared signal from the system for
approximately 4 minutes in order to preserve their battery power. The signal may be lost if the system is turned off or if the headphones are out of range of the infrared signal transmitters.
Each set of headphones has a rotary volume control on one of the earpieces. To adjust the volume, adjust this control.
Audio to the wireless headphones is provided over 2 channels. Audio for channel 1 or channel 2 is selected from one of the available sources using the remote control. Pressing the button in the center of the headphone volume
control will switch the headphone between channels.
Video
The local video input is the standard yellow RCA color-coded jacks. A composite video signal from a device can be attached to this input and is then available to be sourced to one or both of the rear screens. To use this video
input, connect the auxiliary device cables to the RCA jacks and power ON both the auxiliary device and the rear seat entertainment system.
Power for the device is not supplied by this connection. The rear seat entertainment system cannot control the operation of devices connected to the RCA jacks. All operation of the device must be done using the controls
available on the device.
B+ L
O
C
X51L
KR73 Fuse Block -
Ignition Instrument D
Main Panel Left E
Relay S
C
F39DL F25DL
10A 10A
X2 35 28
Data
2840 Communication
RD/GY Schematics
J220
UV6
2840 1639 3894 1102 3999 3894 3998 3997 3998 3997
RD/GY VT/BK GN/BK GY/GN WH/VT GN/BK GY/VT WH/GN GY/VT WH/GN
X1 7 8 21 3 5 20 17 18 2 1
P16
Instrument
Cluster
A90
B+ IGN Logic
X1 19
1851
BK/WH
G218
L
O
C
D
4 E
P16 A7 S
Instrument C
Fuel Pump
Km/h Cluster D and Level
RPM B46
MPH Sensor
Fuel Assembly
40
A90 Level
250 Sensor
Logic
6281
BK/GN
J375
451 X2 60 X3 1 2 17 X3 8 X1 9 10 26 25
BK/WH K20
5V 5V Engine
Control
Module
G110
L
O
C
K20 D
Engine E
Control S
C
Module
5V
X3 64 27 44 X2 41 61 25
2 1
B37B
Engine Engine Oil
Controls P Pressure
Schematics U Sensor
3
1589 6281 6281 1937
BU/VT BK/GN BK/GN BU/WH
J375
6281 6281
BK/GN BK/GN
P16
(-UHS) (-UHS) (-UHS) (-UHS) Instrument
4 3 B C Cluster
- +
A7 A6D
Fuel Pump Fuel Pump
and Level and Level A90
Sensor Sensor Logic
Assembly Assembly -
Secondary
B46 B46B
Fuel Fuel Level
40 Level 40 Sensor - Km/h
250 250 RPM P9 MPH Km/h
Sensor Secondary MPH
Driver Information
Center Display
L
P16 O
C
Instrument
Cluster
D
E
S
C
- +
2
A90
Logic
P9
Driver Information TC P ABS
Center Display
A90
Logic
X1 27 25 24 12 30 16
K20
Engine
Control
Module L96 L96 UEU/UFL/UHX-UV6 UEU/UFL/UHX-UV6
L83/L86 L83/L86
636 61 X225 17 19
BU/GY BK/BU
636 61
BU/GY BK/BU
X150 13 14
X106 6 5
636 61 636 61
D-BU/GY BK/BU BU/GY BK/BU
1 1
K9 B9 B9
Body Ambient Air Ambient Air
Control Temperature Temperature
Module Sensor Sensor
2 2
L
O
C
B+
D
E
X51L S
Fuse Block C
- Instrument
F39DL Panel Left
10A
X2 35
P16
A90 Instrument
Logic Cluster
D
X1 21 X2 BK
2840
RD/GY
J220
3894
GN/BK
LVDS
2840
RD/GY
X1 6 1 X2 BK
P29
B+ D Head-Up
Display
X1 4 3 8
4 3
S27
Head-Up
Display
+ HUD Switch
-
INFO
G218
Audible Warnings
L
B+ O
C
X51L A11 P16 M74D
Fuse Block Radio A90 Instrument A90 Window
- Instrument Logic Cluster Logic Motor - D
F16DL E
2A Panel Left Driver S
C
X2 5 6
-BTM
745
GY
5040
RD/BU
Door Lock/
X201 4 Indicator
Schematics
5040
RD/BU
4
S39
Ignition
Switch
III
I II
1020
WH/VT
X3 15
K9
Body
Control
Module
X1 22
13
GN/GY
Exterior
Lights
Schematics
• Driver Seat Belt Reminder – If the vehicle is started and the seat belt is unbuckled, the BCM requests the radio or audio amplifier sound a chime to indicated that the belt is unbuckled. This is accompanied by a flashing
driver seat belt indicator on the instrument cluster. If the belt remains unbuckled, the chime cycle may continue multiple times if the vehicle is driven and the indicator will remain on solid.
• Passenger Seat Belt Reminder – If the passenger presence system determines that their is an occupant in the passenger seat and the vehicle is started with the passenger seat belt unbuckled, the BCM requests the
radio or audio amplifier sound a chime to indicated that the belt is unbuckled. This is accompanied by a flashing passenger seat belt indicator. If the belt remains unbuckled, the chime cycle may continue multiple times if
the vehicle is driven and the indicator will remain on solid. If an object is placed on the passenger seat, the passenger presence system may interpret this as a passenger occupying the seat. Because the passenger seat
belt is unbuckled, the passenger seat belt reminder chime will sound. To correct this, remove the object from the passenger seat.
• Exterior Lamps On Warning – If the exterior lamps are left on after the ignition is turned off and the driver door is opened, the BCM will request the radio or audio amplifier sound a chime as an indicator that the exterior
lamps are on.
• Electric Parking Brake (if equipped) – If the electric parking brake switch is pressed while the vehicle is in motion, the parking brake control module will request the radio or audio amplifier sound a chime. To release the
parking brake, the brake pedal must be pressed when the electric parking brake switch is pressed. If the brake pedal is not pressed, the parking brake control module will request the radio or audio amplifier sound a chime.
A message will also appear on the driver information center.
• Delayed Locking – If the keyless entry transmitter is not in the vehicle and the door lock switch is pressed with the driver door open, the BCM will request the radio or audio amplifier sound a chime three times to indicate
that the vehicle has entered a delayed locking state. The doors will automatically lock five seconds after the last door is closed.
• Object Detection – The object detection system sends various chime requests to the radio or audio amplifier during normal operation.
Additional Warnings
The following warnings have an associated instrument cluster indicator or driver information center message:
• Turn Signal Indicators – The radio or audio amplifier activates the audible warning as requested by the BCM.
• Vehicle Overspeed Message – The radio or audio amplifier activates the audible warning as requested by the BCM.
• Fuel Level Low Message – The radio or audio amplifier activates the audible warning as requested by the BCM.
• Oil Pressure Indicator – The radio or audio amplifier activates the audible warning as requested by the BCM.
• Tire Pressure Low Indicator – The radio or audio amplifier activates the audible warning as requested by the BCM.
• Antilock Brake Indicator – The radio or audio amplifier activates the audible warning as requested by the electronic brake control module.
• Engine Cooling System Messages – The radio or audio amplifier activates the audible warning as requested by the engine control module.
• Transmission Messages – The radio or audio amplifier activates the audible warning as requested by the transmission control module.
• Head-Up Display
• Instrument Cluster
Head-Up Display
The head-up display is a slave device to the instrument cluster. The head-up display is powered through ignition voltage and ground. It communicates directly with instrument cluster via serial data and only has limited self-
diagnosis capacity. Head-up display DTCs are reported through the instrument cluster.
The head-up display projects a full color image onto the windshield and is only viewable from the driver seat. The image location and brightness is adjustable using the head-up display switch. The image information is received
from the instrument cluster through a video cable.
Instrument Cluster
The instrument cluster sends the image information to the head-up display via a discrete video cable. The image sent to the head-up display is closely related to the information currently being displayed on the instrument cluster
or driver information center. For example, if an incoming phone call is displayed in the cluster, this information will be displayed on the head-up display. If a navigation alert is shown in the cluster, then a turn-by-turn alert will
display on the head-up display. When the operator interacts with the instrument cluster using the steering wheel mounted driver information center switch, the head-up display also responds to the interaction. If the operator
dismisses the navigation alert on the instrument cluster, it is also removed from the head-up display.
Standard/Speed Configuration
The head-up display projects only the vehicle speed. Additionally, the outside air temperature, compass, and time may also be displayed.
Audio Configuration
The head-up display will project the current audio information when listening to the audio system and the active phone information if the operator is on a phone call.
Navigation Configuration
The head-up display will project navigation information. If a current route is being followed, turn by turn instructions and arrows will be displayed. If no route is programed, the compass heading is displayed.
Performance Configuration
The head-up display will project RPM and PRNDL information.
MESSAGE DISPLAYED
Refer to the OWNER’S MANUAL for descriptions and explanations of all messages displayed.
For diagnosis and repair information related to a displayed message refer to the System Diagnosis and the Description of Operation that the message relates to.
BRAKES OVERHEATED
The Electronic Brake Control Module monitors brake usage and compares it to an internal thermal model to determine if the brakes could become overheated. If the Electronic Brake Control Module determines the brakes pads
have exceeded a desirable temperature based on the thermal model, it sends a serial data message to the Instrument Cluster to display the BRAKES OVERHEATED message. The message remains displayed until the
estimated temperature returns to a desirable range.
A7 T12
B37 B46 Fuel Pump B34 B14A Automatic B115
Engine Oil Fuel and Level Engine Transmission Transmission Vehicle
Pressure Level Sensor Coolant Output Shaft Assembly Speed
Switch Sensor Assembly Temperature Speed Sensor
Sensor Sensor
AT MT
K20
Engine
Control
Module
1500
B9 S78
Ambient Air Turn Signal/
Temperature Multifunction
Sensor Switch
2500
P16
P9 Instrument
Driver Information Cluster
Center Display
• The ECM detects a malfunction in the engine oil pressure sensor signal circuit.
• The BCM detects a loss of serial data communications with the ECM.
• The instrument cluster detects a loss of serial data communications with the BCM.
Speedometer
The instrument cluster displays the vehicle speed based on the information from the ECM. The ECM sends the vehicle speed information via serial data to the BCM. The BCM then sends the vehicle speed information via serial
data to the instrument cluster to display the vehicle speed.
Odometer
The instrument cluster displays the vehicle odometer in the driver information center. The ECM send a distance rolling count message via serial data to the body control module (BCM). The BCM uses this information to calculate
the vehicle odometer. This odometer value is then sent to the instrument cluster. The instrument cluster does not calculate the odometer.
The odometer value is stored in multiple modules. The instrument cluster is a secondary storage module for the odometer, while the BCM is the primary storage and accumulator.
In addition to storing the odometer value for the vehicle, the instrument cluster and the BCM store the VIN. Software checks are performed to ensure these modules, and their stored odometer information, can not be move or
transferred between different vehicles.
Tachometer
The instrument cluster displays the engine speed based on the information from the ECM. The ECM converts the data from the crankshaft position sensor to an engine revolution signal. The ECM sends the engine speed
information via serial data to the BCM. The BCM then sends the information via serial data to the instrument cluster to display the engine speed.
Compass
The vehicle compass information is gather through the compass module or vehicle communication interface module (VCIM). The compass module or VCIM determines vehicle direction and communicates this with the BCM
through serial data. The BCM sends the compass information to the instrument cluster via serial data, where it is displayed.
• Simple – The most basic of the available configurations, the Simple configuration includes four static information display zones and one interactive information display zone. The infotainment display zone is located on the
left side of the display and displays phone, turn-by-turn navigation, and audio information. The speedometer and compass are located in the upper middle of the display. On the right side of the display is a graphical
representation of the fuel level and fuel range.
Below the speedometer, in the lower middle of the display, is the interactive information display zone. The information display zone contains multiple pages that can be scrolled through and selected using the steering
wheel mounted driver information center switch.
• Performance – The Performance configuration contains three static information zones, one interactive information display zone, and one interactive application display zone. The speedometer and tachometer/fuel level
gauge are located on the left and right of the display. In between the speedometer and tachometer is a static information display zone that displays current information while the operator scrolls through other pages in the
interactive application display zone.
In the middle of the speedometer is an interactive information display zone. This display zone has a limited number of selection and will only display a digital speedometer, a navigation map, a settings page with sub-
menus, or a blank page.
• Balanced – The Balanced configuration contains three static information zones, two interactive information display zones, and one interactive application display zone. The tachometer is located on the left side of the
display, the speedometer in the middle, and the coolant temperature/fuel level gauge on the right.
Located in the tachometer is an interactive information display zone.
In the speedometer is an interactive information display zone. This display zone has a limited number of selection and will only display a digital speedometer, a navigation map, a settings page with sub-menus, or a blank
page.
An interactive application display zone is located in the coolant temperature/fuel level gauge. The application display zone allows access to the navigation application, audio application, phone application, or settings
application.
• Enhanced – The Enhanced configuration contains four static information zones, two interactive information display zones, and one interactive application display zone. The speedometer in the upper middle of the display,
a navigation map or compass in located on the upper left, and a fuel level gauge and fuel range display on the right.
Located on the left and right lower portion of the display are interactive information display zones.
An interactive application display zone is located in the middle of the display. The application display zone allows access to the navigation application, audio application, phone application, or settings application.
B+ L
O
C
X51R
Fuse Block -
F12DR Instrument D
2A Panel Right E
S
C
X2 16
3040
RD/YE
X201 25
5
3040 S70R
RD/YE Steering
Wheel
Controls
Switch -
X1 1 Right
X85 A90
Steering B+ Logic
Wheel Air
Bag Coil
X2 10
6 9 10 7 8 3
J295
3040 1 2 1 2
RD/YE S70E S70F P16
Steering Steering A90 Instrument
Wheel Wheel Logic Cluster
Controls Controls
Switch - Switch -
10 Radio Radio
S70L 3 Presets 3 Volume
B+ Steering
Wheel
Controls
Switch
- Left 1050 1050 1050
BK BK BK
G210
B+ L
O
C
F12DR D
E
2A S
C
X2 16
3040
RD/YE
X201 25
3040
RD/YE
X1 1
X85
Steering Wheel
Air Bag Coil
X2 10 P16
A90 Instrument
3040 Logic Cluster
RD/GY
J295
3040 3040
RD/GY RD/GY
7
S70L
Steering
Wheel
Controls
Switch -
Left
1 3
7 1 3 5
S70R
Steering
Wheel
SEL Controls
Switch -
A90 Right
B+ Logic
6
1050
BK
G210
S70E S70F
Steering Steering
Wheel Wheel
Controls Controls
Switch - Switch -
Radio Radio
Presets Volume
S70R
Steering
Wheel
Controls
Switch -
Right
P16
Instrument
Cluster
A11
Radio
The steering wheel control switches duplicate the function of the primary controls of the associated component, through a network of momentary contact switches.
The Steering Wheel Controls are divided into a right-hand set and left-hand set. The right-hand switch is connected to the IPC LIN serial data and provides input from the left-hand, left-hand rear, and right-hand rear switches
The right-hand switch controller consists of UP/DOWN/LEFT/RIGHT directional, center “select” , Push-to-Talk, and Mute buttons. The LEFT/RIGHT buttons navigate the display regions of the cluster. The UP/DOWN buttons
navigate the menus. The right-hand rear switch consists of volume up and volume down buttons. The left-hand rear switch consists of favorite up and favorite down buttons.
Starting System
L
O
X6 A C
X50D K20
Fuse Engine
Block - Control D
E
Battery Module S
L83/L86 L96 C
IGN P/N
F2UD F2UD
175A 250A X1 63 51 (L83/L86) K84 X2 58 (L83/L86)
Keyless X1 34 (L96)
X1 27 19 (L96)
Entry 1786
Control WH/GY
Module
X5 A X2 A 439
1 242 625 VT/GN
RD RD/GN YE/BK BTM MYC/MYD M5U
X6 A X2 D3 X175 35
X50A X1 3
KR73 Fuse Block -
Ignition Underhood Q8 1786
F104UA Main Control WH/GY
40A Relay Solenoid
Valve X176 12
30 85 F74UA Assembly
KR27 15A X2 F 1786
Starter WH/GY
Relay WH
1
B15 B15
Transmission Transmission
87 86 Internal Internal
Automatic Automatic
Transmission Mode Switch Transmission Mode Switch
Controls Controls
X2 E2 F2 M7 (L96) Schematics Schematics
2 6 X2 A2 (L83/L86)
RD/YE YE
K9
X2 A X1 A Body 2
M64 Control GY 3927
Starter Module BK/GY
X2 A
Motor
5V X176 20
M
X3 22 15 3927
K71 BK/GY
+ -BTM -BTM Transmission
C1 Control
Battery 1073 1020 T12
WH/BK WH/VT Module
X175 30 Automatic
6 5 Transmission
X1 5 T12 3297 Assembly
S39 BK/GY
- Ignition Automatic
550 Switch 451 Transmission
450 BK BK/WH Assembly 25
BK K71
III Transmission
Control
I II Module
L83/L86 L96 L96 L83/L86
65
451
BN/WH
P16 L
P9 Instrument O
Driver Information Cluster C
X6 A
- + Center Display
X50D D
Fuse E
Block - A90 S
Battery Logic C
F2UD
250A
X2 A
1 2
RD RD/YE
+
C1 K20
Battery Engine
Control
Module
X3 17 X1 47
23 25
GY BN
X2 A X1 2 1
B S F L P G13
Generator
250 450
BK BK
G102 G120
P16 L
P9 Instrument O
Driver Information Cluster C
B+ - + Center Display
X6 A
X50A X50D D
Fuse Block - Fuse E
Underhood Block - A90 S
F26UA Logic C
5A Battery
F2UD
175A
X4 M1
2340
RD/YE
X2 A
X4 20
K9
B+ Body
Control
Module
5V
X4 26 X5 6 X4 18 21 1 2
RD RD/YE
+
C1
Battery 23 25
GY BN
-
B C A X2 A X1 2 1
B18 B S F L P G13
Battery Generator
Current
Sensor
250 450
BK BK
L
B+ O
C
X50A F38DR K9
Fuse Block - Body
Underhood Control D
Module E
F103UA S
10A C
X5 14
X50E 300
Fuse Block X2 G6
VT/BN
- Battery
F1UE Auxiliary
1 100A 300 X1 33
RD VT/BN
X61A
+ + X6 A Junction
Block -
C1B C1 X50D X115 42 Instrument
Battery - Battery Fuse X1 A
Panel
Auxiliary Block -
F1UD Battery X5 18
3440 300
100A RD/WH VT/BN
- -
KI4/KI5 NP0/NQH
X158 3 1
X1 A
30 86
KR79
Auxiliary
Battery Cigar Lighter/ Transfer Case
Relay 2 Power Outlet Control
Schematics Schematics
87 85
X3 A X1 A
KR81
Auxiliary
Battery
Relay 1
X2 A X1 B
550 550
BK BK
• Always shield your eyes and avoid leaning over the battery whenever possible.
• Do not expose the battery to open flames or sparks.
• Do not allow the battery electrolyte to contact the eyes or the skin. Flush immediately and thoroughly any contacted areas with water and get medical help.
• Follow each step of the jump starting procedure in order.
• Treat both the booster and the discharged batteries carefully when using the jumper cables.
Batteries that are no longer wanted must be disposed of by an approved battery recycler and must never be thrown in the trash or sent to a landfill.
Batteries that are not part of the vehicle itself, not the battery under the hood, must only be transported on public streets for business purposes via approved hazardous material transportation procedures.
Battery storage, charging and testing facilities in repair shops must meet various requirements for ventilation, safety equipment, material segregation, etc.
The maintenance free battery is standard. There are no vent plugs in the cover. The battery is completely sealed except for 2 small vent holes in the side. These vent holes allow the small amount of gas that is produced in the
battery to escape.
The battery has 3 functions as a major source of energy:
• Engine cranking
• Voltage stabilizer
Battery Ratings
A battery has 2 ratings:
• Amperage hours
When a battery is replaced use a battery with similar ratings. See battery specification label on the original battery.
Amperage Hours
The amperage hour rating tells you how much amperage is available when discharged evenly over a 20 hour period. The amperage hour rating is cumulative, so in order to know how many constant amperage the battery will
output for 20 h, you have to divide the amperage hour rating by 20. Example: If a battery has an amperage hour rating of 74, dividing by 20 = 3.75. Such a battery can carry a 3.75 A load for 20 hours before dropping to 10.5 V.
(10.5 V is the fully discharged level, at which point the battery needs to be recharged.) A battery with an amperage hour rating of 55 will carry a 2.75 A load for 20 hours before dropping to 10.5 V.
• It takes corrective actions by boosting idle speeds, and adjusting the regulated voltage.
The battery condition is estimated during ignition-off and during ignition-on. During ignition-off the state-of-charge of the battery is determined by measuring the open-circuit voltage. The state-of-charge is a function of the acid
concentration and the internal resistance of the battery, and is estimated by reading the battery open circuit voltage when the battery has been at rest for several hours.
The state-of-charge can be used as a diagnostic tool to tell the customer or the dealer the condition of the battery. Throughout ignition-on, the algorithm continuously estimates state-of-charge based on adjusted net amp hours,
battery capacity, initial state-of-charge, and temperature.
While running, the battery degree of discharge is primarily determined by a battery current sensor, which is integrated to obtain net amp hours.
In addition, the electrical power management function is designed to perform regulated voltage control to improve battery state-of-charge, battery life, and fuel economy. This is accomplished by using knowledge of the battery
state-of-charge and temperature to set the charging voltage to an optimum battery voltage level for recharging without detriment to battery life.
The Charging System Description and Operation is divided into 3 sections. The first section describes the charging system components and their integration into the electrical power management. The second section describes
charging system operation. The third section describes the instrument panel cluster operation of the charge indicator, driver information center messages, and voltmeter operation.
P16
Instrument
Cluster
K20
Engine
Control
Module
G13
Generator
C1
Battery
K9 B18
Body Battery
Control Current
Module Sensor
• Charge Mode
• Headlamp Mode
• Start Up Mode
The engine control module (ECM) controls the generator through the generator turn ON signal circuit. The ECM monitors the generator performance though the generator field duty cycle signal circuit. The signal is a pulse width
modulation (PWM) signal of 128 Hz with a duty cycle of 0–100 percent. Normal duty cycle is between 5–95 percent. Between 0–5 percent and 95–100 percent are for diagnostic purposes. The following table shows the
commanded duty cycle and output voltage of the generator:
10% 11 V
20% 11.56 V
30% 12.12 V
40% 12.68 V
50% 13.25 V
60% 13.81 V
70% 14.37 V
90% 15.5 V
The generator provides a feedback signal of the generator voltage output through the generator field duty cycle signal circuit to the ECM. This information is sent to the body control module (BCM). The signal is PWM signal of
128 Hz with a duty cycle of 0–100 percent. Normal duty cycle is between 5–99 percent. Between 0–5 percent and 100 percent are for diagnostic purposes.
Charge Mode
The BCM will enter Charge Mode when ever one of the following conditions are met.
• GMLAN (Climate Control Voltage Boost Mode Request) is true, as sensed by the HVAC control head. High speed cooling fan, rear defogger and HVAC high speed blower operation can cause the BCM to enter the Charge
Mode.
When any one of these conditions is met, the system will set targeted generator output voltage to a charging voltage between 13.9–15.5 V, depending on the battery state of charge and estimated battery temperature.
Headlamp Mode
The BCM will enter Headlamp Mode when ever the headlamps are ON (high or low beams). Voltage will be regulated between 13.9–14.5 V.
Start Up Mode
When the engine is started the BCM sets a targeted generator output voltage of 14.5 V for 30 seconds.
• The engine control module (ECM) detects that the generator output is less than 11 V or greater than 16 V. The instrument panel cluster receives a GMLAN message from the ECM requesting illumination.
• The instrument panel cluster determines that the system voltage is less than 11 V or greater than 16 V for more than 30 seconds. The instrument panel cluster receives a GMLAN message from the body control module
(BCM) indicating there is a system voltage range concern.
• The instrument panel cluster performs the displays test at the start of each ignition cycle. The indicator illuminates for approximately 3 seconds.
Display Message: BATTERY NOT CHARGING SERVICE CHARGING SYSTEM or SERVICE BATTERY CHARGING SYSTEM
The BCM and the ECM will send a serial data message to the driver information center for the BATTERY NOT CHARGING SERVICE CHARGING SYSTEM or SERVICE BATTERY CHARGING SYSTEM message to be
displayed. It is commanded ON when a charging system DTC is a current DTC. The message is turned OFF when the conditions for clearing the DTC have been met.
K9
Body
Control
Module
K20
Engine
Control
Module
G13
Generator
Idle Boost 1 Start Less Than −15°C (5°F) Less Than 13 V — First level Idle boost
requested
Idle Boost 1 Start — — Battery has a net loss First level Idle boost
greater than 0.6 Ah requested
Idle Boost 1 End Greater Than −10°C (14°F) Greater Than 12 V Battery has a net loss First level Idle boost
less than 0.2 Ah request cancelled
Idle Boost 2 Start — — Battery has a net loss Second level Idle boost
greater than 1.6 Ah requested
Load Shed 1 Start — — Battery has a net loss of 4 Rear Defrost, Heated
Ah Mirrors, Heated Seats,
HVAC cycled OFF for
20% of their cycle
Load Shed 1 End — Greater Than 12 V Battery has a net loss of Clear Load Shed 1
less than 2 Ah
Idle Boost 3 Start — — Battery has a net loss of Third level Idle boost
10 Ah requested
Idle Boost 3 End — Greater Than 12 V Battery has a net loss of Third level Idle boost
less than 6.0 Ah request cancelled
Load Shed 2 Start — — Battery has a net loss Rear Defrost, Heated
greater than 12 Ah Mirrors, Heated Seats,
HVAC cycled OFF for
50% of their cycle. The
BATTERY SAVER
ACTIVE message will be
displayed on the DIC
Load Shed 2 End — Greater Than 12 V Battery has a net loss of Clear Load Shed 2
less than 8 Ah
Load Shed 3 Start — Less Than 11.9 V Battery has a net loss Rear Defrost, Heated
greater than 20 Ah Mirrors, Heated Seats,
HVAC cycled OFF for
100% of their cycle. The
BATTERY SAVER
ACTIVE message will be
displayed on the DIC
Load Shed 3 End — Greater Than 12.6 V Battery has a net loss of Clear Load Shed 3
less than 13 Ah
Idle Boost and Load Shed Without Current Sensor (based on battery voltage)
Idle Boost 1 Start Less Than −15°C (5°F) Less Than 13 V First level Idle boost requested
Idle Boost 1 Start — Less Than 12.6 V First level Idle boost requested
Idle Boost 1 End Greater Than −15°C (5°F) — First level Idle boost request
cancelled
Idle Boost 1 End — Greater Than 13 V First level Idle boost request
cancelled
Idle Boost 2 Start — Less Than 12.4 V Second level Idle boost requested
Idle Boost 2 End — Greater Than 12.5 V Second level Idle boost request
cancelled
Load Shed 1 Start — Less Than 12.3 V Rear Defrost, Heated Mirrors,
Heated Seats, HVAC cycled OFF
for 20% of their cycle
Idle Boost 3 Start — Less Than 10 V Third level Idle boost requested
Idle Boost 3 End — Greater Than 12.3 V Third level Idle boost request
cancelled
Load Shed 2 Start — Less Than 12.1 V Rear Defrost, Heated Mirrors,
Heated Seats, HVAC cycled OFF
for 50% of their cycle. The
BATTERY SAVER ACTIVE
message will be displayed on the
DIC
Load Shed 3 Start — Less Than 11.9 V Rear Defrost, Heated Mirrors,
Heated Seats, HVAC cycled OFF
for 100% of their cycle. The
BATTERY SAVER ACTIVE
message will be displayed on the
DIC
K20
Engine
Control
Module
C1 KR27 K9 T12
Battery Starter Body Automatic
Relay Control Transmission
Module Assembly
M64 S39
Starter Ignition
Motor Switch
Cruise Control
L
O
C
D
E
S
P16 C
P9 Instrument
Driver Information Cluster
Center Display
A90
S70L Logic
Steering
6190 698 499 1400 Wheel
Controls
3400 1740 1780 499 1400 Switch -
Left
X2 7 3 2 -5W4/9C1 5W4/9C1
X85
Steering J358
Wheel Air
Bag Coil
6311 6311
X1 4 8 6 WH/BU WH/BU
X3 16 9 4 X5 12
K9
F19DL Body
Control
Module
B+ L
O
X51R C
Fuse Block -
F28DR Instrument D
10A Panel Right E
S
C
X1 43
3140
RD/GN
J403
3140
RD/GN
Data
Communication
X150 23 Schematics
1 10 8 7 6 5
K14
B+ IGN Distance
Sensing
Cruise
Control
3 Module
150
BK
G102
K20
Engine
Control
Module
S70L P16
Steering Instrument
Wheel Cluster
Controls
Switch -
Left
K9
Body
Control
Module
Cruise control is a speed control system that maintains a desired vehicle speed under normal driving conditions at speeds above 40 km/h (25 mph). Steep grades may cause variations in the selected vehicle speeds.
The following are the main components of the Cruise Control System:
The body control module (BCM) monitors the signal circuit of the cruise control switches, which are located on the steering wheel. The BCM relays the cruise control switch status to the engine control module (ECM) via the serial
data circuit. The ECM uses the status of the cruise control switch to determine when to capture and maintain the vehicle speed. The ECM monitors the vehicle speed signal circuit in order to determine the desired vehicle speed.
Voltage is supplied to the cruise control switch via the steering wheel control switch reference voltage circuit supplied by the BCM. The cruise control function switches are arranged in a resistive ladder design, with each cruise
control function switch having a different resistance value. The BCM detects a specific voltage value that is associated with the cruise control function switch being activated. The BCM sends a serial data message to the ECM
indicating that the on/off switch is active. Similarly, when the normally open + RES switch or the normally open − SET switch are pressed, the switch closes and the BCM detects the predetermined voltage signal on the cruise
control resume/accel and set/coast switch signal circuit. The BCM sends a serial data message to the ECM indicating that the + RES switch or the − SET switch is active.
• On/Off
• − SET
To engage the Cruise Control System, ensure that the vehicle speed is above 40.2 km/h (25 mph), turn the cruise On/Off switch ON and momentarily press the − SET switch. The ECM will engage the Cruise Control System and
record the vehicle speed. The ECM sends a serial data message to the instrument panel cluster (IPC) in order to illuminate the Cruise Engaged indicator in the IPC. Refer to the vehicle owner’s manual for the location and
operation of the cruise control On/Off indicators and driver information center (DIC) messages.
Pressing the accelerator pedal while the Cruise Control System is engaged, allows the driver to override the Cruise Control System in order to accelerate the vehicle beyond the current set vehicle speed. When the accelerator
pedal is released, the vehicle will decelerate and resume the current set vehicle speed.
The driver can also override the current set vehicle speed via the − SET switch and the + RES switch. When the Cruise Control System is engaged, pressing and holding the − SET switch will allow the vehicle to decelerate from
the current set vehicle speed without deactivating the Cruise Control System. When the − SET switch is released, the ECM will record the vehicle speed and maintain the vehicle speed as the new set vehicle speed. When the
Cruise Control System is engaged, momentarily pressing the − SET switch will allow the vehicle to decelerate at a vehicle specific calibratable increment, commonly 1.6 km/h (1 mph), each time that the − SET is momentarily
pressed, with a minimum vehicle speed of 38 km/h (24 mph). Refer to the vehicle Owner’s Manual for more information.
Pressing and holding the + RES switch, when the Cruise Control System is engaged, will allow the vehicle to accelerate to a greater vehicle speed than the current set vehicle speed. When the + RES switch is released, the ECM
will record the vehicle speed and maintain the vehicle speed as the new set vehicle speed. When the Cruise Control System is engaged, momentarily pressing the + RES switch will allow the vehicle to accelerate at a vehicle
specific calibratable increment, commonly 1.6 km/h (1 mph), each time that the + RES switch is momentarily pressed. Momentarily activating the + RES switch will recall the previous vehicle speed, after the cruise control system
has been disengaged by pressing the brake pedal, or CANCEL switch. Refer to the vehicle Owner’s Manual for more information.
The Cruise Control System will disengage when the brake pedal is applied. The body control module (BCM) monitors the BPP sensor via the BPP sensor signal circuit as the voltage signal increases while the pedal is further
applied. The ECM monitors the BPP signal through a discrete input and a serial data message signal from the BCM indicating the brake status. When either signal indicates the brake pedal is applied, the ECM will disengage the
cruise control system.
The Cruise Control System will also disengage when the cruise control on/off switch is switched OFF, or the cruise control cancel switch is activated. The body control module (BCM) determines when the cruise control cancel
switch is activated. When the normally open cancel switch is closed, the BCM detects the predetermined voltage signal on the cruise control function switch circuit. The vehicle speed stored in the memory of the engine control
module will be erased when the cruise control On/Off switch is turned OFF, or the ignition switch is turned OFF. The BCM sends a serial data message to the ECM in order to disengage the cruise control system. When the
Cruise Control System has been disengaged, the ECM sends a serial message to the instrument panel cluster (IPC) in order to turn OFF the Cruise Engaged indicator.
Every time the Cruise Control System is disengaged, the ECM will keep track of the reason for system disengagement. The last 8 disengagement reasons will be recorded within the ECM memory. The scan tool will display the
last 8 Cruise Disengage History parameters, in which one out of approximately 50 possible reasons will be displayed in each of these 8 parameters. For the disengagement reason to be displayed within the scan tool parameter
the Cruise Control System is active and disengagement is requested.
When engagement of the system is requested but an engagement inhibit is present, the most recent inhibit reason is recorded in the ECM history. The scan tool will display the most recent inhibit reason, in which one out of
approximately 50 possible reasons will be displayed.
• The ECM has not detected a brake pedal activation from the body control module (BCM) this ignition cycle.
• The Antilock Brake System (ABS)/Traction Control System (TCS) is active for more than a calibratable time (typically 0.3 to 0.7 seconds).
ACC BRAKE INOP Adaptive Cruise Control Automatic Braking Adaptive Cruise Control Automatic Braking Inoperative
Failed
ACC INHIBIT Adaptive Cruise Control Inhibited Adaptive Cruise Control Inhibited
ACC OPTION Adaptive Cruise Control option mismatch Cruise control type (adaptive cruise or conventional
cruise) mismatched between ECM and BCM.
ACCEL Time Rate Limiting Fault Cruise torque request rate limiting active too long
APP OVERRIDE Pedal greater than cruise (override) Driver has overridden cruise control set speed with
accelerator pedal for greater than an allowable time.
Auto Brk Data Automatic Braking Engine Torque Request ECM to EBCM serial data fault is active or
Signal Communication Malfunction communication has been lost between ECM and
EBCM.
BPP DATA DTC P0703 active or maximum time elapsed Serial data fault is active or communication has been
without receiving valid Brake Pedal Position lost with module sending brake pedal apply state
signal.
BPP DTC Brake Pedal Position signal invalid Brake Pedal Apply Circuit fault has been detected.
BPP Not Learned Brake Apply Sensor Home Position Not Brake Pedal Position Sensor Released Position Not
Learned Learned.
Brk Ped Press Brake Pedal Driver Applied Pressure Detected A Brake Pedal Apply has been detected based on
brake pedal pressure as measured by the EBCM.
COAST DISENGAGE Coast disengage Cruise control is in coast mode with the Set/Coast
switch depressed and is requesting no throttle
COAST SPEED LOW Coast below low speed inhibit Set / Coast switch was depressed. Vehicle slowed
below minimum cruise operating speed.
Cruise Brk Inop Brake System Malfunction EBCM has detected a failure that does not allow
automatic braking to be performed.
CRUISE S/W Sequence of completion checks Cruise control software execution error has occurred.
CRUISE SW DATA Serial data fault (Cruise switch serial Cruise switch serial data fault is active or
communication fault) communication has been lost with module sending
cruise switch states
CRUISE SW. OFF On/Off switch in Off state Cruise On/Off switch turned Off
D WHL SPD HI Driven Whl Spd Greater (wheel slip detection) Driven wheel speed greater than Non Driven wheel
speed (slip detection)
D WHL SPD LOW Un-driven Whl speed Greater Non Driven wheel speed greater than driven wheel
speed
ECM INHIBIT PCM/ECM inhibit (RAM corruption) ECM internal communication error
ECT OVERTEMP Engine metal overtemp active Engine over temperature. Overheated.
ENG RUN TIME Engine run time not elapsed Engine has not been running long enough, typically
five seconds.
ENGINE SPEED Engine speed too low or too high Engine RPM too low (near stall) or too high (near
engine RPM fuel shutoff).
HIGH SPEED Vehicle speed exceeds high speed threshold Vehicle speed has exceeded maximum cruise
operating speed
HIGH VOLTAGE Voltage above high voltage threshold Ignition Voltage High at ECM (typically 18 volts)
ILLEGAL MODE Illegal cruise mode Cruise control mode is incorrect based on switch
states.
LOST FWD GEAR Transmission in neutral. Reverse or park Gear selector not in forward gear
LOW SPEED Vehicle speed drops below low speed Vehicle speed dropped below the cruise control
threshold minimum operating speed. May be due to hilly terrain
and low vehicle speed. Manual transmission gear
selection and engine torque may contribute to this
disengagement reason.
LOW VOLTAGE Voltage below low voltage threshold Ignition Voltage Low at ECM (typically 9 volts)
MPH LIMIT MPH Limited Fuel (Vehicle overspeed fuel cut- Vehicle overspeed protection active with fuel cut off
off active) active
M/T Gear Changed Manual transmission out of gear with no clutch Manual transmission shifted to Neutral without clutch
pedal apply pedal being applied.
OVER SET SPEED Over schedule Vehicle speed has exceeded driver selected set
speed by more than an allowable amount. This may
occur while driving down a significant grade or driver
overriding cruise while performing a passing
maneuver.
PARK BRAKE Park Brake Switch signal Active Parking Brake Applied
PTO ACTIVE Power Take Off Active Power Take Off is active.
Ram DTC Processor Integrity Fault (Ram corruption) ECM software error has occurred
RPM LIMIT Injectors Disabled (Engine overspeed fuel cut- Engine RPM limiter active with fuel cut off active.
off active)
S/C ON SPEED HI Over schedule tap-down Set/Coast switch selected, vehicle speed is above set
speed and does not decrease. May be due to traveling
down hill
SIMUL S/C-R/A SET and RESUME switches simultaneously Set/Coast and Resume Accelerate switches pressed
active simultaneously
SL/W Sys On Speed Limiter / Warning On/Off switch turned Driver has turned on the Speed Limiter/Warning on/off
on switch. Cruise is disabled / inhibited and cruise on/off
switch will be set to OFF.
SW. INVALID Analog cruise switch input out of range Cruise switch voltage signal in invalid range
TAC INHIBIT ETC prevents cruise operation Electronic Throttle Control has detected a failure in the
throttle control hardware
TRANS DTC Trans Gear Fault Transmission DTC is active or in history that inhibits
cruise control operation
UNDER SET SPEED Under schedule Vehicle speed is below cruise control set speed by
more than an allowable amount
• The radar processes the road environment to get data concerning any vehicle ahead of the ACC vehicle. Detection, parameter estimation, tracking, object classification and diagnostics are the primary radar functions.
When an object is detected, the controller calculates the object range, range rate, acceleration and azimuth angle parameters.
• The cruise control vehicle distance sensor module performs ACC state processing automatically – distance control or speed control. The ACC System operates in 2 possible states – Cruise or Follow. The normal
operating state is Cruise, whereby the vehicle speed is controlled to match the driver selected set speed. When a preceding forward target is identified by the radar, the ACC System will automatically transition into the
follow speed state to provide proper lane spacing behind the target vehicle in front. The preceding vehicle's speed and acceleration, with the ACC vehicle speed, acceleration and distance between the two vehicles will be
used to determine the ACC follow speed limit. The ACC follow speed limit will ensure that an acceptable distance is maintained to the preceding vehicle.
• The cruise control vehicle distance sensor module determines the follow speed limit for throttle control by the ECM.
• The cruise control vehicle distance sensor module arbitrates the ACC System brake and throttle control between the EBCM and the ECM.
• The cruise control vehicle distance sensor module requests brake light activation during automatic braking.
• The cruise control vehicle distance sensor module provides operational feedback to the vehicle driver. The cruise control vehicle distance sensor module sends signals for telltales and messages to be displayed on the
instrument cluster or driver information center.
• The BCM provides a translating gateway for the high speed GMLAN serial data circuit.
• The BCM reads all cruise control switches and the gap switch. The cruise control vehicle distance sensor module monitors a variety of user operated switches from the BCM switch status information sent via the GMLAN
serial data circuit.
• The BCM illuminates the brake light based on a GMLAN message from the cruise control vehicle distance sensor module during automatic braking.
• The BCM measures the brake pedal position and sends brake pedal travel status via GMLAN serial data circuit to the ECM. The ECM disengages the ACC System when the brake is applied by the driver pressing the
brake pedal.
• The BCM serves as a gateway to the instrument cluster and driver information center. The BCM will generate visual warnings based on high speed GMLAN serial data messages from the cruise control vehicle distance
sensor module.
• The ECM provides the electronic throttle control to the ACC System. The ECM is also responsible for determining when a driver is overriding the adaptive cruise control throttle position by pressing the accelerator pedal.
• The ECM processes the cruise control switch requests received via the GMLAN serial data circuit from the BCM. Engaging and disengaging the ACC System are functions performed by the ECM.
• The ECM determines the driver selected vehicle speed. Unless the ACC module requests a lower vehicle speed, the ECM will control the vehicle speed to the driver selected set speed.
• The EBCM provides automatic braking for the ACC System. The cruise control vehicle distance sensor module will request vehicle deceleration via high speed GMLAN serial data circuit.
• The EBCM determines when the driver–applied brake pressure is active. The EBCM will communicate this status via the GMLAN serial data circuit to the BCM.
• The EBCM releases vehicle automatic braking when there is a throttle override by the driver pressing the accelerator.
• Service ACC
Accelerator Pedal
Deceleration of the ACC vehicle to maintain a certain distance and speed while a slower moving vehicle is in its path is achieved through throttle control by the ECM and the application of light automatic braking by the EBCM.
During automatic braking the ECM is commanded to release the throttle from the currently controlled cruise position by the cruise control vehicle distance sensor module. At the end of automatic braking, the ECM will control the
vehicle speed to the current set vehicle speed. Driver throttle override occurs when the driver of the ACC vehicle depresses the accelerator pedal with the intention of requesting greater speed than the current throttle position. An
example is an ACC vehicle driver stepping on the accelerator for a passing maneuver. The ECM continuously monitors the throttle and reports a throttle override condition. When no throttle override is present, automatic braking
is allowed. When throttle override is detected by the ECM, automatic braking in not allowed to affect the vehicle acceleration.
• On/Off switch
• Set/decrease switch
• Resume/increase switch
The cruise control function switches are arranged in a resistive ladder design whereby each switch function is set up with different resistance values. The BCM through the cruise control switch signal circuit detects a
predetermined voltage value when any cruise control switch function is activated. The associated cruise control function signal detected by the BCM is then sent to the engine control module (ECM) as a GMLAN serial data
circuit message. The ECM on receiving the message provides the cruise control function requested by the BCM. The ECM is responsible for recognizing and responding to cruise control switch requests sent by the BCM. The
cruise control function switches are used by the ECM to communicate to the cruise control vehicle distance sensor module the driver selected vehicle speed. The driver selected vehicle speed is communicated through GMLAN
serial data circuit to the cruise control vehicle distance sensor module and the BCM. The ACC System engages and adjusts vehicle speeds based on the activation of the following cruise control function switches:
On/Off Switch
The BCM monitors the switch signal circuit in order to determine when the On/Off switch is disabled or activated. The BCM detects a predetermined voltage value on the switch signal circuit. The On/Off switch state is then
relayed to the ECM via the GMLAN serial data circuit. The ECM sends the On/Off switch input status to the cruise control vehicle distance sensor module. When the On/Off switch is turned ON, the ACC System enters either a
standby enabled or a standby disabled mode. The standby enabled mode indicates that every condition required for the ACC System to function has been met, but the ACC is not engaged. When the ACC is in the standby
disabled mode, the conditions necessary for the ACC System to function has not been met. When the On/Off switch is turned OFF, the ACC will enter the disabled mode. The ACC will not activate in the disabled mode.
Set/Decrease Switch
The ACC System is engaged when the ACC On/Off switch is turned ON and the set/decrease switch is momentarily pressed and released . When the set/decrease switch is pressed, the selected vehicle speed is set to the
current vehicle speed by the ECM. The vehicle speed must be at or greater than 40 km/h (25 MPH). The selected vehicle speed is displayed by the driver information center. While in the engaged state, the selected vehicle
speed and the following distance can be adjusted. Pressing and holding the set/decrease switch, when the ACC System is engaged, will decrease the selected vehicle speed without deactivating the ACC. Momentarily pressing
and releasing the set/decrease switch, when the adaptive cruise control is engaged, will decrease the vehicle speed by a calibrated amount. Refer to the vehicle Owner’s Manual for the specific amount of speed reduction for
each switch press.
Resume/Increase Switch
The resume/increase switch is used in order to increase the selected vehicle speed when ACC is active. The amount selected vehicle speed can be increased from the resume/increase switch depends on how long the switch is
pressed. The presence of a slower moving vehicle in the path of the ACC vehicle will limit the extent to which the selected vehicle speed can be achieved. If there is no preceding vehicle in front, limiting the ACC vehicle
acceleration, then the vehicle speed that is attained is the new selected vehicle speed. The current selected vehicle speed is displayed by the driver information center. Acceleration is terminated when the resume/increase
switch is released. Momentarily pressing and releasing the resume/increase switch, when the adaptive cruise control is engaged, will increase the vehicle speed by a calibrated amount. Refer to the vehicle Owner’s Manual for the
specific amount of speed increase for each switch press.
Gap Switch
The gap switch allows the driver to determine how closely the adaptive cruise control (ACC) vehicle follows a target vehicle while ACC is engaged. When the ACC vehicle speed is being limited due to a slower travelling vehicle,
the ACC vehicle speed is automatically controlled to the follow speed limit. The gap switch has 3 following distance selections that range from 1–2 s. The gap switch following distance between the ACC vehicle and the target
vehicle is expressed in time as opposed to actual distance. The distance maintained for a selected gap will vary based on vehicle speed. The faster the vehicle speed, the further back you will follow. The gap setting can only be
Set Speed
The ACC vehicle set speed is displayed at all times in the driver information center when ACC is engaged. The cruise control vehicle distance sensor module set speed display request is sent to the instrument cluster via the
GMLAN serial data circuit.
Follow Distance
The driver information center displays the driver selected following distance when ACC is engaged and the gap switch is active. The current follow distance setting is displayed in the driver information center for a few seconds
after the gap switch is pressed to increase or decrease the following distance. The cruise control vehicle distance sensor module follow distance display request is sent to the instrument cluster via the GMLAN serial data circuit.
Cruise Engaged
The Adaptive Cruise Control (ACC) System will engage and adjust vehicle speeds based on the activation of the following cruise switches:
• On/off
• Set/decrease
• Resume/increase
ACC will not engage if any inhibit criteria is active. Also, the driver must step on the brakes at each ignition cycle before attempting to engage ACC. The engine control module (ECM) looks to the BCM for the brake initial travel
achieved signal indicating that the driver has stepped on the brakes before attempting to engage ACC.
The vehicle speed must be above 45 km/h (28 MPH) and below 190 km/h (118 MPH) for the ACC System to be engaged. In the engaged state, the ACC System allows the driver to override the controlled vehicle speed
temporarily while still remaining in the engaged state.
Cruise Inhibited
Cruise Control Vehicle Distance Sensor Module Inhibits
The cruise control vehicle distance sensor module inhibits the Adaptive Cruise Control (ACC) System when any of the following conditions exists:
• Initial brake pedal travel signal from brake pedal position sensor is not present
• The FRONT RADAR BLOCKED CLEAN FRONT of VEHICLE indicator is active in the driver information center.
• The Cruise Switch failed message from the BCM is sent to the cruise control vehicle distance sensor module.
• Automatic braking failure – A GMLAN signal from the electronic brake control module (EBCM) the to cruise control vehicle distance sensor module indicating an automatic braking failure
• The cruise control vehicle distance sensor module transceiver temperature is hot.
ECM Inhibits
The ECM inhibits the ACC System operation when any of the following conditions exists:
• The ACC inhibited signal from cruise control vehicle distance sensor module is present.
• Automatic braking failure – A GMLAN signal from EBCM to the ECM indicating an automatic braking failure
• The initial brake pedal travel signal from the brake pedal position sensor is not present.
Cruise Disengaged
The Adaptive Cruise Control (ACC) System disengages when any of the following occurs:
Pressing the brake pedal while the ACC is engaged will disengage the ACC System.
L
B+ O
C
X50A
Fuse Block -
Underhood D
F116UA F123UA E
40A 40A S
C
X1 E2 B2
342 642
RD/WH RD/GY
2 2
G10L G10R
Cooling Cooling
Fan Fan
B+ Motor - B+ Motor -
Left Right
M M
4 1 4 1
J130
473
BN/YE
150 250
X139 2 BK BK
473
BN/YE
X1 59 (L83/L86)
X1 41 (L96)
K20
Engine
Control
Module
G101 G102
The cooling fan speed is effected by many different conditions and the ECM will adjust the duty cycle from 0–100 percent based on cooling system requirements. The scan tool output control is only capable of operating the
cooling fan increments, between 10–90 percent. 90 percent is considered high speed fan. When multiple cooling fan speed requests are received, the ECM operates the fan at the highest of speed requests. The ECM commands
the fans ON under the following conditions:
• If the engine coolant temperature at key-off is warmer than a predetermined value, or the A/C pressure is greater than a predetermined value, the cooling fan will operate at a low speed. The fan will shut OFF if the
temperature or pressure drops below the predetermined value, but will only operate for 2 minutes, regardless of the coolant temperature or A/C pressure.
ENGINE OVERHEATED
The IPC displays ENGINE OVERHEATED message when the IPC receives a message from the PCM requesting illumination of this driver warning.
Cooling System
The cooling system's function is to maintain an efficient engine operating temperature during all engine speeds and operating conditions. The cooling system is designed to remove approximately one-third of the heat produced by
the burning of the air-fuel mixture. When the engine is cold, the coolant does not flow to the radiator until the thermostat opens. This allows the engine to warm quickly.
Cooling Cycle
Coolant is drawn from the radiator outlet and into the water pump inlet by the water pump. Coolant will then be pumped through the water pump outlet and into the engine block. In the engine block, the coolant circulates through
the water jackets surrounding the cylinders, where it absorbs heat.
Some coolant is also pumped from the water pump to the heater core, then back to the water pump. This provides the passenger compartment with heat and defrost.
The coolant is then forced through the cylinder head gasket openings and into the cylinder heads. In the cylinder heads, the coolant flows through the water jackets surrounding the combustion chambers and valve seats, where it
absorbs additional heat.
Coolant
The engine coolant is a solution made up of a 50-50 mixture of DEX-COOL and suitable drinking water. The coolant solution carries excess heat away from the engine to the radiator, where the heat is dissipated to the
atmosphere.
Radiator
The radiator is a heat exchanger. It consists of a core and two tanks. The aluminum core is a tube and fin crossflow design that extends from the inlet tank to the outlet tank. Fins are placed around the outside of the tubes to
improve heat transfer to the atmosphere.
The inlet and outlet tanks are a molded, high temperature, nylon reinforced plastic material. A high temperature rubber gasket seals the tank flange edge to the aluminum core. The tanks are clamped to the core with clinch tabs.
The tabs are part of the aluminum header at each end of the core.
The radiator also has a drain cock (except HD), located in the bottom of the right hand tank. The drain cock unit includes the drain cock and drain cock seal.
The radiator removes heat from the coolant passing through it. The fins on the core transfer heat from the coolant passing through the tubes. As air passes between the fins, it absorbs heat and cools the coolant.
Surge Tank
The surge tank is a plastic tank with a threaded pressure cap. The tank is mounted at a point higher than all other coolant passages. The surge tank provides an air space in the cooling system that allows the coolant to expand
and contract. The surge tank provides a coolant fill point and a central air bleed location.
During vehicle use, the coolant heats and expands. The increased coolant volume flows into the surge tank. As the coolant circulates, any air is allowed to bubble out. Coolant without air bubbles absorbs heat much better than
coolant with bubbles.
During vehicle use, the coolant heats and expands. The increased coolant volume can in some conditions push past the pressure cap and through a channel into the overflow bottle. As the coolant circulates, air is allowed to
bubble out. This air is then transferred to the overflow bottle, through the surge tank cap, where it returns to the atmosphere. Coolant without air bubbles absorbs heat much better than coolant with bubbles. When the engine
cools, the coolant, without air bubbles, contracts back into the surge tank from the bottom of the overflow bottle.
Pressure Cap
The pressure cap seals the cooling system. It contains a blow off or pressure relief valve and a vacuum or atmospheric valve. The pressure valve is held against its seat by a spring, which protects the radiator from excessive
cooling system pressure. The vacuum valve is held against its seat by a spring, which permits opening of the valve to relieve vacuum created in the cooling system as it cools off. The vacuum, if not relieved, might cause the
radiator and/or coolant hoses to collapse.
The pressure cap allows cooling system pressure to build up as the temperature increases. As the pressure builds, the boiling point of the coolant increases. Engine coolant can be safely run at a temperature much higher than
the boiling point of the coolant at atmospheric pressure. The hotter the coolant is, the faster the heat transfers from the radiator to the cooler, passing air.
The pressure in the cooling system can get too high. When the cooling system pressure exceeds the rating of the pressure cap, it raises the pressure valve, venting the excess pressure.
As the engine cools down, the temperature of the coolant drops and a vacuum is created in the cooling system. This vacuum causes the vacuum valve to open, allowing outside air into the surge tank. This equalizes the
pressure in the cooling system with atmospheric pressure, preventing the radiator and coolant hoses from collapsing.
• After the vehicle is shut OFF if the engine coolant temperature at key-off is:
The PCM commands the high speed fans ON under the following conditions:
At idle and very low vehicle speeds the cooling fans are only allowed to increase in speed if required. This insures idle stability by preventing the fans from cycling between high and low speed.
Power, Ground, Serial Data and Front Blower Controls (X88 or Z88)
B+ B+ L
O
C
X51R X51L P17
Fuse Block - Fuse Block Info
P7
F45DR Instrument F28DL F24DL - Instrument Display D
Display E
40A Panel Right 10A 15A Panel Left Module
S
OFF AUTO C
A90
X1 22 X2 25 15 Logic
X2 3 9
5060 7531
X217 1 X215 4 5 GN GN/YE
1 X2 1 9 2 4
M8 K33
B+ IGN HVAC
Blower
Motor Control
B+ Module
M
6 2 X2 15 8
G210 G218
B+ B+ L
O
C
X51R X51L P17
Fuse Block - Fuse Block Info
P7 A20
F45DR Instrument F28DL F24DL - Instrument Display D
Display Radio/HVAC Controls E
40A Panel Right 10A 15A Panel Left Module
S
C
A90
X1 22 X2 25 15 Logic
X1 12 8
X217 1 X215 4 5
1 X2 1 9 2 4
M8 K33
B+ IGN HVAC
Blower
Motor Control
B+ Module
M
6 2 X2 15 8
G210 G218
B+ L
O
X51L P17 C
X53A
KR73 Fuse Block Info Fuse
Ignition P7 Display
- Instrument F18RA Block - D
Main Display Module
Panel Left 30A Rear E
Relay AUTO Body S
31 C
F36DL A90
10A Logic
X3 13 (AZ3)
X2 38 (D07) SYNC A26
R CTRL HVAC 1740
Controls RD/GY
1739
VT/GN
X490 4
AZ3 D07
X2 9
J320 X300 8
7531 1740
GN/YE RD/GY
X487 9 1
1 3 X1 3 6
A34 K8A
HVAC Blower
Controls - A90 Motor
Auxiliary Logic Control
Module -
A90 Auxiliary
IGN Logic
X216 12
P7 AUTO X1 5 X2 1 2
Display
7531 2211 101 5988
GN/YE GN/BK GY/BN (SWB) BU/BK (SWB)
4
X2 4 16 101 5988
K33 RD/BU (-SWB) OG (-SWB)
HVAC 1450
Control BK 2 (SWB)
AZ3 D07 Module B (-SWB)
M8B
Blower Motor -
1050 1851 M Auxiliary
BK BK
A (-SWB)
1 (SWB)
B+ L
O
X51L P17 C
KR73 Fuse Block Info X53A
Ignition - Instrument P7 A20 Display Fuse
Main Panel Left Display Radio/HVAC Controls Module F18RA Block - D
Relay 30A Rear E
Body S
31 C
F36DL
10A A90
Logic
X2 38
X1 8
X300 8 X490 4
1740
RD/GY
X487 9 1
1 3 X1 3 6
A34 K8A
HVAC Blower
Controls - A90 Motor
Auxiliary Logic Control
Module -
Auxiliary
A90
IGN Logic
X216 12
X1 5 X2 1 2
4
7531 2211 101 5988
GN/YE GN/BK GY/BN (SWB) BU/BK (SWB)
A (-SWB)
1 (SWB)
G218 G402
J259 L
Headlights/ O
Daytime C
10 10
M37B M6B Running Lights Theft Deterrent
Mode Door Air (DRL) System D
M Actuator - M Temperature Schematics Schematics E
Auxiliary Door S
C
Actuator - 278 728
5 6 8 9 5 6 8 9 Auxiliary WH/D-BU GY
5 1 6
B10B
5729 2775 Ambient
5730 407 2599 2614 407 2145 598
WH/OG BK/YE GY Light/
BK/GN GY GY BK/YE GY/BU GY/RD Sunload
J455 Sensor
A90
Logic
X487 2 3 11 5 6 13 12 4
X216 20 19 8 18 17 16 15 14 2 4 3
590 1783 734 1791
GY YE/VT BU/WH BK/YE
5729 5730 407 2599 2775 2614 2145 598
GN/WH BK/GN BK/YE GY WH/BN GY GY/BU GY/RD X215 12 13 11 10
590 1783 1783 734
GY YE/VT YE/VT BU/WH
X4 13 14 X3 9 X4 15 17 18 19 X1 20 14 13 4
K33
HVAC
Control
Module
5V
X3 2 3 X2 17 X3 4 11 12 13 X3 16 17 18 X2 18 X4 5 6 7
J257
2273 119 598 2275 2210 1199 598 733 2274 1614 598 1838 1791 2778 1236 598 1646 1791
YE/BN WH GY/RD WH/GN GY/GN BU/BN GY/RD BU/YE YE/BK GN GY/RD VT/GN BK/YE GY/BK WH/BK GY/RD BN/BU BK/YE
6 5 3 2 6 5 3 2 6 5 3 2 6 5 3 2
M37L M6L M4 M6R
Mode Door Air Air Inlet Air
M Actuator - M Temperature M Door M Temperature
Left Door Actuator Door
Actuator - Actuator -
1 1 Left 1 1 Right
J255
L
O
K33 C
HVAC
Control D
Module E
S
C
X1 18 19 X3 1 X4 11 9 12 X3 20 9
404 405
BN BN/BK
X216 10 9
X487 7 10
404 405
BN BN/BK
(SWB)
B7G B7C B7H B7D B7J B7E B39
Air Air Air Air Air Air A/C Evaporator
Temperature Temperature Temperature Temperature Temperature Temperature Temperature
Sensor - Sensor - Sensor - Sensor - Sensor - Sensor - Sensor
Duct Upper Duct Lower Duct Left Duct Left Duct Right Duct Right
Auxiliary Auxiliary Upper Lower Upper Lower
407 407
BK/YE BK/YE
J455
X487 11
407
BK/YE
X216 8
407
BK/YE
J258
L
B+ P16 O
K33 Instrument C
X50A P9 Cluster
HVAC Driver Information
Fuse Block - Control
Underhood Center Display D
Module E
S
KR75 F60UA C
Engine Controls B+ A90
10A Logic
Ignition Relay X2 11 10
7573 7574
KR29 BU/BN BU/YE
A/C
Compressor
Clutch Relay
X216 7 6
X2 A1 C1
7573 7574
459 59 BU/BN BU/YE
WH/GY BN/GN
X115 2 20
7573 7574
BU/BN BU/YE 2
B1
A/C
P Refrigerant
U Pressure
Sensor
1 3
2 2 G1
Q2 Q46 A/C
A/C A/C Compressor
Compressor Compressor
Clutch Solenoid 2700 5514 380
Valve BN/RD BK/BN GN
1 1
550
BK
X1 21 22 6 (L83/L86)
X1 32 (L83/L86)
X1 53 (L96) X1 26 13 12 (L96)
K20
5V Engine
Control
Module
G110
• Recirculation Operation
• Automatic Operation
• Engine Coolant
• A/C Cycle
Feature Availability
Purge Yes
Personalization Yes
Actuators
Doors in the HVAC case assembly are used to control air flow. The HVAC control module operates the doors through the use of actuators, with one actuator being used for each door. The system has the following air control
doors and associated actuators: mode, left and right temperature, and recirculation.
Each actuator used in the system is a 5-wire bi-directional electric motor that incorporate a feedback potentiometer. The five circuits are, low reference, 5 V reference, actuator position signal, and two control circuits. The control
circuits use either a ground or 12 V value to coordinate the actuator movement. In order to move the actuator, the HVAC control module grounds one of the control circuits while providing the other with 12 V. The HVAC control
module reverses the polarity of the control circuits to move the actuator in the opposite direction.
When the actuator shaft rotates, the potentiometer’s sliding contact changes the door position signal between 0–5 V. The HVAC control module converts the voltage signal to counts. The total range of the counts is 0–1024, with
an operating range between 20–1000. The actual operating range of an actuator is determined during calibration. During calibration, the actuator is moved though its full range of travel and the module stores the minimum and
maximum value. Based on the desired system operation, the module sets a commanded, or targeted, value for the actuators. The control circuits are operated to move the door to the required position, and the changing position
signal is sent to the module. Once the actual position signal and the commanded value are the same, the module ceases operating the control circuits and the actuator (and door) remain in the desired position.
Blower Motor
The blower motor control module is an interface between the HVAC control module and the blower motor. The blower motor speed control from the HVAC control module, battery positive and ground circuits enable the blower
motor control module to operate. The HVAC control module provides a pulse width modulation (PWM) signal to the blower motor control module in order to command the blower motor speed. The blower motor control module
transfers the PWM signal into a corresponding blower motor voltage.
A/C Compressor
The A/C compressor uses a conventional belt driven magnetic clutch to engage and mechanically turn the compressor. When the A/C switch is pressed, the HVAC control module sends an A/C request message to the ECM via
serial data. If specific criteria is met, the ECM then grounds the A/C compressor clutch relay control circuit, which will switch the A/C compressor clutch relay. With the relay contacts closed, battery voltage is supplied to the
permanently grounded A/C compressor clutch. The A/C compressor clutch will then be activated.
This A/C system utilizes a variable displacement solenoid valve to alter the amount of displacement created by the turning of the compressor. The HVAC control module provides both battery voltage and a pulse width modulated
ground to the variable displacement solenoid valve. When the A/C switch is pressed, the HVAC control module grounds the variable displacement solenoid using a (PWM) signal in order to determine the amount of compressor
displacement. The performance of the A/C compressor is regulated based on cooling load.
Air Speed
The blower control switch is part of the HVAC controls. The selected value of the blower switch position is sent to the HVAC control module via LIN-Bus. The blower motor control circuitry is integrated within the blower motor
assembly. The HVAC control module provides a low side pulse width modulation (PWM) signal to the blower motor to request a specific motor speed. The blower motor translates the PWM signal and drives the motor
accordingly.
Afterblow
Afterblow is a feature that dries the evaporator core by operating the blower motor after the engine is turned OFF. This reduces the amount of microbial growth that can create undesirable odors. The vehicle does not come
equipped with the afterblow feature turned ON. If the afterblow feature is required due to an odor concern, it must be enabled using the scan tool Afterblow configuration function.
After the HVAC control module has been programmed for afterblow, the following conditions must be met for afterblow to operate:
• The A/C compressor operated for more than 2 minutes before shut down.
Once the above conditions have been met, the blower motor will perform the following sequence up to 5 times. This could last up to an hour:
Air Delivery
The HVAC control module controls the distribution of air by the use of recirculation and mode door actuator. The modes that may be selected are:
• Defrost
• Defog
• Panel
• Floor
The desired air distribution mode can be selected with the air distribution switches at the HVAC control. The HVAC control delivers the values to the HVAC control module via LIN-Bus. The HVAC control module controls the
mode door actuator so that it drives the flap to the calculated position. Depending on the position of the flap, air is distributed through various ducts leading to the outlets in the dash. Turning the mode flap to the defrost position,
the HVAC control module will move the recirculation actuator to outside air, reducing window fogging. When defrost is selected, the blower motor will be activated, regardless of the coolant temperature. The HVAC control module
enables a high volume of air delivered to the front defrost vents. A/C is available in all modes.
The rear window defogger does not affect the HVAC system.
• Mode setting
• A/C high side pressure is between 269–2 929 kPa (39–425 PSI)
The air streams into the passenger compartment through the heater core and the evaporator core. The air temperature actuator drives the mixed air flap to direct the airflow. If the interior temperature should be increased, the
mixed air flap is put into the position in which more air streams through the heater core. If the interior temperature should be decreased, the mixed air flap is put into the position in which more air streams through the evaporator
core.
Recirculation Operation
The recirculation switch is integrated into the HVAC control. The selected recirculation switch position is sent to the HVAC control module via LIN-Bus. The HVAC control module controls the air intake using the recirculation
actuator. In recirculation mode the recirculation flap opens in order to circulate the air within the vehicle. In fresh air mode the recirculation flap is closed in order to route outside air into the vehicle.
Automatic Operation
In automatic operation, the HVAC control module maintains the comfort level inside of the vehicle by controlling the A/C compressor clutch, the blower motor, the air temperature actuators, mode actuator and recirculation
actuator.
To put the HVAC system in automatic mode, the following is required:
When the warmest position is selected in automatic operation the blower speed will increase gradually until the vehicle reaches normal operating temperature. When normal operating temperature is reached the blower stays on
Engine Coolant
Engine coolant is the essential element of the heating system. The thermostat controls the normal engine operating coolant temperature. The thermostat also creates a restriction for the cooling system that promotes a positive
coolant flow and helps prevent cavitation.
Coolant enters the heater core through the inlet heater hose, in a pressurized state. The heater core is located inside the HVAC control module. The ambient air drawn through the HVAC control module absorbs the heat of the
coolant flowing through the heater core. Heated air is distributed to the passenger compartment, through the HVAC control module, for passenger comfort. Opening or closing the air temperature flap controls the amount of heat
delivered to the passenger compartment. The coolant exits the heater core through the return heater hose and recirculates back to the engine cooling system.
A/C Cycle
Refrigerant is the key element in an air conditioning system. There are currently two approved Environmental Protection Agency refrigerants. They are R134a and R-1234yf, and either one could be used in this vehicle. R-1234yf
is a newly EPA approved refrigerant, and it will require the use of an updated Air Conditioning Refrigerant Recovery/Recharge Cart/System. Refer to CELL Link Error - Link target cell (cell ID 48139) is invalid for this publication. for
correct tool usage. Both refrigerants are very low temperature gases that can transfer the undesirable heat and moisture from the passenger compartment to the outside air.
The compressor builds pressure on the vapor refrigerant. Compressing the refrigerant also adds heat to the refrigerant. The refrigerant is discharged from the compressor, through the discharge hose, and forced to flow to the
condenser and then through the balance of the A/C system. The A/C system is mechanically protected with the use of a high pressure relief valve. If the A/C refrigerant pressure sensor fails or if the refrigerant system becomes
restricted and refrigerant pressure continued to rise, the high pressure relief will pop open and release refrigerant from the system.
Compressed refrigerant enters the condenser in a high temperature, high pressure vapor state. As the refrigerant flows through the condenser, the heat of the refrigerant is transferred to the ambient air passing through the
condenser. Cooling the refrigerant causes the refrigerant to condense and change from a vapor to a liquid state.
The condenser is located in front of the radiator for maximum heat transfer. The condenser is made of aluminum tubing and aluminum cooling fins, which allows rapid heat transfer for the refrigerant. The semi-cooled liquid
refrigerant exits the condenser and flows to the Receiver/Dehydrator(R/D).
The R/D contains desiccant that absorbs moisture that may be in the refrigerant system. The R/D also acts as a storage vessel to ensure that a steady flow of liquid reaches the thermal expansion valve. The refrigerant exits the
R/D and flows through the liquid line to the thermal expansion valve.
The thermal expansion valve is located at the front of dash and attaches to the evaporator inlet and outlet pipes. The thermal expansion valve is the dividing point for the high and the low pressure sides of the A/C system. As the
refrigerant passes through the thermal expansion valve, the pressure on the refrigerant is lowered. The thermal expansion valve also meters the amount of liquid refrigerant that can flow into the evaporator.
Refrigerant exiting the thermal expansion valve flows into the evaporator core in a low pressure, liquid state. Ambient air is drawn through the HVAC control module and passes through the evaporator core. Warm and moist air will
cause the liquid refrigerant boil inside of the evaporator core. The boiling refrigerant absorbs heat from the ambient air and draws moisture onto the evaporator. The refrigerant exits the evaporator through the suction line and back
to the A/C compressor, in a vapor state, and completing the A/C cycle of heat removal. At the A/C compressor, the refrigerant is compressed again and the cycle of heat removal is repeated.
The conditioned air is distributed through the HVAC control module for passenger comfort. The heat and moisture removed from the passenger compartment will also change form, or condense, and is discharged from the HVAC
control module as water.
L
O
P17 C
B+ Info
Display
X51L Module D
E
Fuse Block S
F27DL - Instrument C
10A Panel Left K60
Steering
Column A26
Lock HVAC
Module Controls
X84
X2 26 Data Link
Connector JX300
16 5 4 1 D
8
5060 5060 X2 3
GN GN
X201 12
X275 25
BTM X88/Z88
(Not Used) (Not Used) (Not Used)
A B C D F E
JX200
G H J K L M
(Not Used) (Not Used) (Not Used)
5060
GN
X215 2
X2 2 X1 15
K33 K56
HVAC Serial Data
Control Gateway
Module Module
G218 G210
L
O
C
K40P
K124 B218L K182 K84 Seat D
E
K9 Active Side Object Parking Keyless K85 Memory S
Body Safety Sensor Assist Entry Passenger Control C
Control Control Module - Control Control Presence Module -
Module Module Left Module Module Module Passenger
X7 23 X2 7 1 X1 4 3 X1 2 X2 1
J305
5060 5060 5060 5060
GN GN X495 17 GN GN
-ULT ULT
5060
GN
5060
GN
X320 26
UGN+Z75 UKC UD5/UD7 BTM
5060
GN
A B C D E F
JX300
G H J K L M
(Not Used)
X1 40
X900 13 X185 8 X61A X310 26
Junction
5060 5060 Block -
GN GN Instrument 5060
Panel GN
X3 47
X1 7 X1 15 X2 8
5060
GN
11 X2 1 D
X275
K39 K36 K4
Liftgate Inflatable Assist
Control Restraint Step
Module Sensing Control B174W K40D
and Module Frontview Seat
Diagnostic Camera - Memory
Module Windshield Control
Module -
Driver
L
O
B+ C
X51L
Fuse Block D
- Instrument E
F28DL S
Panel Left C
10A
Data
Communication
Schematics
X2 25
3340 5060
RD/VT GN
X1 1 15
K56
B+ Serial Data
Gateway
Module
X1 6 X2 10
1102
GY/GN
J203
X275 32
1102 1102 1102 1102 1102
GY/GN GY/GN GY/GN GY/GN GY/GN
1102
GY/GN
1851
BK/WH
X1 12 (Z75)
X1 3 X1 3 (-Z75) X1 1 X1 14 X1 11
P16 P17 K73 A11 A33
Instrument Info Telematics Radio Media Disc
Cluster Display Communication Player
Module Interface
Control Module
UVH -UVH
1102
J340 GY/GN
X3 1
T3
1102 1102 Audio
GY/GN GY/GN Amplifier
X3 1 X2 3
T3 K157
Audio Video
Amplifier Processing
Control
Module
G218
L
O
C
(Not Used) (Not Used)
17 16
K14 K20 D
E
Distance 120 Engine S
Sensing Control C
X2 7 6
Cruise Module
Control X61A
Module Junction
8 7 X1 39 40 (L83/L86) Block -
Instrument
X1 29 43 (L96) Panel
9 X8 10 9
K59 K59 -K59 -K59
2500 2501
BU WH
J153
X4 5 4
J152
2501 2500 2501
WH BU WH
2500 2501
BU WH 9
E F
J210 J211
X115 6 5
K17
Electronic L
X61A O
Junction Brake C
Block - Control
X84 Instrument Module
Data Link Panel 9 8 21 20 D
E
Connector 9 9 S
6 C
14 E F
2500 2501 2500 2501
9 9 BU WH BU WH
2500 2501
BU 2500 2501
WH BU WH
L96 L83/L86 L83/L86 L96 -Z95 Z95 Z95 -Z95
J210
39 24
X182 10 9 2500 K19 2501
J211 BU Suspension WH
Control
9 Module
9
2500 2501 40 25
WH/BN BK/L-GN
2500 2501
BU WH 9
X1 7 6
K43
Power 2500 2501
Steering BU WH
Control
Module
X1 2 1
-J71 J71 J71 -J71
F L
9 K83
2500 2501
BU Park WH
Brake
X2 1 2 2500 2501 Control
K56 BK L-GN/L-BU Module
Serial Data
Gateway G K
Module X182 3 2
9 9
X1 7 8
2500 2501 2500 2501
BU WH BU WH
9 27 28
2500 K38 2501
BU Chassis WH
2500 2501 Control Module
BU WH
X6 24 25
9 26 29
K9
Body
2500 2501 Control
BU WH Module
9
X1 25 24
2500 2501
9 BU WH
A B (-J71/JL1/Z85/Z95)
2500 2501 R6A
BU WH 120 Terminating Resistor -
High Speed Bus
L
O
C
1305 1304 3936 3935
WH/GN BU/GN WH/GY BU/GY D
E
S
X1 11 12 14 13 X2 13 14 4 3 C
K56
120 Serial Data
120 Gateway
Module
X1 3 4 X2 5 6
X1 10 12
1304 K73 1305 9
Telematics 9
BU/GN WH/GN
Communication
Interface
Control Module
X2 3 4 X203 8 9 X295 1 2
9 9
X1 11 12 5 6 X1 6 13
K74 B174W K124
Human Frontview Active
Machine Camera - Safety
Interface Windshield Control
Control Module
X1 13 14 Module
7 8 X1 7 14
9
3935 3936
X203 11 12 BU/GY WH/GY
3935 3936
1304 1305 BU/GY WH/GY
BU/GN WH/GN 9
9
A B A B A B
R6F R6E R6E
Terminating 120 Terminating 120 Terminating
120 Resistor - Resistor -
Resistor -
High Speed High Speed High Speed
Extension Extension Extension
Bus 2 Bus 1 Bus 1
A11
Radio L
O
C
D
E
S
X2 1 2 3 4 C
3997 3998
WH/GN GY/VT
9 3997 3998
WH/GN GY/VT
X1 18 17
P16
Instrument
Cluster
3997 3998
X1 3 4 WH/GN GY/VT
3997 3998
WH/GN GY/VT X225 11 32
9
9
3997 3998
WH/GN GY/VT
3997 3998
WH/GN GY/VT
9
X225 29 8
L
O
C
D
E
S
C
A11
Radio
X2 7
3999
WH/VT
3999
WH/VT
IO3+TG5-UDD IO5/IO6 UDD-IO5/IO6/
TG5/U42/UQA
X275 11
J249
K17 L
O
120 Electronic C
Brake
Control
Module D
X1 18 32 E
5 6 S
X61A C
6105 6106 X84 Junction
BU/YE WH Data Link Block -
12 13 Connector Instrument
9 Panel
9
X5 3 19
6105 6106 G H
BU/YE WH
9
X61A
Junction
Block -
Instrument
Panel
X201 L
O
C
G H
D
E
S
C
6105 6106 6105 6106
BU/YE WH BU/YE WH
9 9
X5 2 1
X61A
Junction -AX7 AX7 AX7 -AX7
Block -
Instrument 7 5
Panel M101R
X1 19 20 Seat Belt
Retractor
Motor
Module -
6105 6106 Right
BU/YE WH 8 6
9
X2 1 9
6105 6106 K124
BU/YE WH Active
9 Safety
Control
Module
X2 2 10
-AX7 AX7 AX7 -AX7
7 5
M101L
Seat Belt 6105 6106
Retractor BU/YE WH
Motor
9
Module -
8 6 Left
X1 18 20
K36
120 Inflatable
Restraint
Sensing
and
X1 22 X1 21 Diagnostic
(Not Used) (Not Used) Module
L
O
C
K20
120 Engine
Control D
Module E
S
C
X1 36 37
7493 7494
BU/BK WH
9
X125 13 14
7493 7494
BU/BK WH
9
4 5
K111
Fuel Pump
120 Driver
Control
Module
L
9 O
C
3811 3813
WH BU/VT X84
5 4 2 3 3813 Data Link D
3811 E
B233B BU/VT WH Connector S
Radar 3 11 C
60 60
Sensor
Module - 9 9
Long
11 10 Range
3813 3811
3813 3811 BU/VT WH
BU/VT WH X150 19 16
9
3813 3811 X225 15 16
BU/VT WH 9
9
-UVZ UVZ UVZ -UVZ 3813 3811
BU/VT WH
J369
X100 12 13
3813 3811
BU/VT 3813 WH J368
3811
BU/VT WH
3813 3811
9 BU/VT WH
9
2 1
B233LF
Radar
Sensor
Module - X315 7 8
Short
7 6 Range
Left Front 3813
9 3811
BU/VT WH
3813 3811 9
BU/VT WH
7 6
8 9
B233RF B174W
Radar Frontview
Sensor Camera -
Module - Windshield
Short
2 1 Range
Right Front 3 4
9
3813 3811
BU/VT WH
3813 3811
BU/VT WH 9
X100 14 15
X315 4 5
9
3813 3811
3813 3811 BU/VT WH
BU/VT WH
J K
X495
X315
L
O
C
J K
D
3813 3811 E
BU/VT WH S
C
9
X495 11 12
3813 9
3811
BU/VT WH
3813 3811
BU/VT WH
7 6
B233LR
Radar
Sensor
Module -
Short
2 1 Range
Left Rear
9
3813 3811
BU/VT WH
7 6
B233RR
Radar
Sensor
Module -
Short
2 1 Range
Right Rear
9
3813 3811
BU/VT WH
X495 19 20
9
3813 3811
BU/VT WH
X2 3 11
K124
60 60 Active
Safety
Control
Module
X2 4 12 14 6
3811 3813
WH BU/VT
L
O
C
K9 D
Body E
S
Control C
Module
X6 16 9 10
J306
-UTT UTT UTT-KA1/KA6/KB6 KA1/KA6+UTT KA1-KB6/UTT
X315 6
X3 2
6132
GN/BN
X320 27
2 4 3 X2 6 X2 6 4 5 4
L
O
C
K38 K39 K20
Chassis P16 Liftgate Engine D
Control Instrument Control Control E
Module Cluster Module Module S
C
K9
Body
Control
Module
X2 21 X3 19 2 30 X1 20 21 X1 15 X1 54
X88/Z88
6135 7527
GN/GY GN/WH 7533 4114 3894 3894 4118 4621
GN/VT GN/VT GN/BK GN/BK GN/BN GN/VT
J371 X300 11 31 X495 18
X106 3
X2 9
3894
GN/BK (X88/Z88)
X1 5 (Z75)
1 2 1 2 3 2 12 X1 3 (X88/Z88) X1 1 1 2
S79LR M45 S79RR S31D S31P K89 K133 S70R P29 K171 M60A
Window Rear Window Seat Seat Immobilizer Trailer Steering Head-Up Hands-Free Active Grille
Switch - Wiper Switch - Heating and Heating and Control Brake Wheel Display Liftgate Air Shutter
Left Rear Motor Right Rear Cooling Cooling Module Power Controls Sensor 1 Motor
Switch - Switch - Control Switch - Control Module
Driver Passenger Module Right Module
L
O
C
P17 K40D
Info Seat
Display Memory D
A22 Module Control E
A26 Radio Module - S
C
HVAC Controls Controls Driver
X2 3
X2 9 X1 5 8
IO5/IO6 A45
7531 7530
GN/YE GN/WH
J251 J215
X310 17
7531 7530
GN/YE GN/WH
J372
X300 10 X225 3
X500 34 X600 34
7527
GN/WH
X505 37 X605 37
X215 3 X203 7 X201 14
X2 4 3 X1 13 X1 9 X1 3 9 X3 4 9
L
O
K40P K40D C
P17
Info Seat Seat
Display Memory Memory D
Module Control Control E
A20 Module - Module - S
C
Radio/HVAC Controls Passenger Driver
X2 4 X2 4 3
X1 8 7 6
ULT ULT
J251
X310 17
7531 7530
GN/YE GN/WH
N38
X300 10 X225 3
X500 34 X600 34
X505 37 X605 37
X215 3 X322 10 X201 14
X2 4 3 X1 13 X1 9 3 2 3 2 9 X3 4 9
K33 A34 A11 K74 S64P K134P S64D K134D S52 K99 S79P
HVAC HVAC Radio Human Seat Seat Bolster Seat Seat Bolster Outside Steering Window
Control Controls - Machine Adjuster Memory Adjuster Memory Rearview Column Switch -
Module Auxiliary Interface Switch - Control Switch - Control Mirror Position Passenger
Control Passenger Module - Driver Module - Switch Control
Module Passenger Driver Module
L
O
K9 C
F19DL Body
Control
Module D
E
S
IGN C
X4 22
5985
VT/YE
-JL1/NP0/NQH JL1/NP0/NQH
J309
X185 20
X2 38
X61A
Junction 5985
Block - VT/YE
Instrument
Panel
X115 16
X9 7
X2 6
K69
IGN Transfer
5985 5985 Case 5985 5985
VT/YE VT/YE Control VT/YE VT/YE
Module
M5U MYC/MYD
X1 18 (L96)
X1 70 (L83/L86) 51 X1 9 7 14
K20 K71 T12 K111 K38
IGN Engine IGN Transmission IGN Q8 Automatic IGN Fuel Pump IGN Chassis
Control Control Control Transmission Driver Control
Module Module Solenoid Assembly Control Module
Valve Module
Assembly
K9 L
F19DL Body O
C
F38DR Control
Module
IGN D
E
S
C
X4 23
5986
WH/BU
J365
X1 12 X1 17 2 2
X185 17 X115 17 X275 23
IGN IGN IGN IGN
X182 8
5986 5986 5986 5986
WH/BU WH/BU WH/BU WH/BU
5986
GY
X1 28 P X1 16 X4 5 X1 10 X1 5 X2 7 X1 9 X1 10
IGN IGN IGN IGN IGN IGN IGN IGN
L
O
C
K124 D
Active E
Safety S
C
Control
Module
X1 10 9
UVZ
3809 3808
BN/VT GY/VT
J334
3808 3808
GY/VT GY/VT
X495 9 X150 22
3809 3808
BN/VT GY/VT
-UVZ UVZ
J494 J111
3808 3808
GY/VT GY/VT
X315 9 X100 19
3809 3809 3808 3808
BN/VT BN/VT GY/VT GY/VT
J106
3808 3808
GY/VT GY/VT
5 5 10 6 5 5
B233LR B233RR B174W B233B B233LF B233RF
IGN Radar IGN Radar IGN Frontview IGN Radar IGN Radar IGN Radar
Sensor Sensor Camera - Sensor Sensor Sensor
Module - Module - Windshield Module - Module - Module -
Short Short Long Short Short
Range Range Range Range Range
Left Rear Right Rear Left Front Right Front
B+ B+ B+ B+ B+ L
O
C
X50A X51L X51R
Fuse Block - Fuse Block Fuse Block -
Underhood - Instrument Instrument D
E
Panel Left Panel Right S
F26UA F19DL F10DL C
5A F11DL F13DR F19DR F38DR F47DR F46DR
10A 10A 20A 20A 20A 10A 15A 15A
X4 M1 X2 18 7 8 X2 7 8 29 X1 34 33
X4 20 X2 1 3 X1 3 X2 4 X1 2 4 X5 3 4
K9
B+ B+ B+ B+ B+ B+ B+ B+ Body
Control
Module
X4 26 X6 3 X1 1 X2 2 X7 23 X6 16 9 10 X2 21 X3 2 19 X1 24 25 X6 25 24 X4 23 22
451 1850 1850 1850 5060 6132 6133 6134 6135 7533 7527 2501 2500 2501 2500 5986 5985
BK/WH BK BK BK GN GN/BN GN/BU GN/YE GN/GY GN/VT OG WH BU WH BU WH/BU VT/YE
Data
Communication
Schematics
G110 G218
L
O
C
D
E
S
C
Automatic
Starting and Transmission Power Theft
Power Charging Horn Controls Moding Fog Lights Deterrent
Moding Immobilizer Schematics Schematics Schematics Schematics Schematics System
Schematics Schematics Schematics
5199 109 5075 5076 5077 28 3287 5526 553 3 4 1020 1073 1317 317 187 192 728
GN/VT BN/GN WH/YE BU/VT BK/VT BN/WH GN/WH VT/YE BU/GY VT/BK VT/YE WH/VT WH/BK BN/WH YE/VT BU/GY BU/GY GY
L83/L86 L83/L86 L83/L86 BTM BTM -BTM -BTM T3U T79 T79 T3U
X4 15 24 18 21 X5 6 19 X3 18 21 14 6 5 15 22 X5 10 5 X1 12 15 21
K9
5V IGN IGN IGN 5V Body
Control
Module
+/-
12V
X7 15 12 18 X6 4 1 2 X5 16 22 X4 22 12 X2 6 27 25 16 X1 26 X6 17 8
-BTM
KB6 KB6
3265 3269 3268 294 195 3271 3267 45 5985 755 5697 3274 3272 3273 3275 5906 5908
YE/BN BN/WH GY/BK BN/YE BU/WH GY/GN VT/YE BU VT/YE GY/VT GY YE/GN GY/WH GY BU/WH GN/VT VT/WH
L
O
C
D
E
S
C
Headlights/ Headlights/
Daytime Trailer Daytime
Running Lights Connector/ Running Lights Exterior
(DRL) Provision Adjustable Transfer Case (DRL) Lights
Schematics Schematics Pedal Control Schematics Schematics
Schematics Schematics
307 524 306 103 278 3691 3691 6812 300 7539 1969 312 712 7538 5065 19 18
YE/BN WH GN/BN WH/VT WH/BU WH/BU WH/BU YE VT/BN BU/BN BN/VT YE YE GY/BU VT/WH BN/GN YE/BU
JF4-A45 NQH
X3 17 11 X1 11 16 X2 10 20 X7 16 X5 23 14 7 18 X4 2 1 7 11 4 X5 1
K9
Body
Control
Module
5V
X5 12 X3 16 9 4 12 24 X2 7 13 26 X5 2 26 X1 22 19 X7 8 X4 3 19 X1 10 X5 8 17
BRS/DL3/ BRS
DR4/Z75
6311 5737 1884 1444 663 664 526 598 111 1314 38 13 552 5996 1315 6844 1134 5186 5187
WH/BU GY/GN BN/GN WH/RD WH/GN VT/BU WH/GN GY/RD GN/WH BU/WH BU/BN GN/GY BKGN GY/GN GN/VT BU/YE BU/VT BU/WH YE/GY
Step/Running Hydraulic
Cruise Control Exterior Board Brake Trailer
Schematics Lights Schematics Schematics Connector/
Schematics Provision
Schematics
L
O
C
D
E
S
C
Antilock
Interior Lights Shift Lock Brake
Dimming Interior Lights Control System
Schematics Body Control
Schematics Schematics System Schematics
Schematics
44 6817 6817 6816 5005 1688 328 7558 156 6815 7557 157 816 1932 4047 1788 6844
YE/GY YE YE WH BK/YE BU/RD GY/GN VT/GN GY WH/BN WH/YE GY YE/WH GN/WH GN/WH BU/VT BU/YE
X2 9 8 X7 9 X1 5 7 13 14 23 X7 19 3 22 1 6 13 X2 18 14 X4 19
K9
5v Body
Control
Module
P B+ 12v
X5 24 X3 10 13 20 25 X4 14 16 17 20 X3 1 2 3 X2 19 15 X7 21 24
860 6009 1714 1715 94 2268 91 196 2340 3277 7533 3276 780 781 244 245
WH/VT BK/GY YE/BU GY WH/BK BN/GY GY BN/GN RD/YE GN/GY GN/VT GY/BK BN/YE BN/WH YE/VT BN/VT
Starting and
Wiper/Washer Charging Immobilizer Door Lock/
Schematics Schematics Schematics Indicator
Schematics
L
O
C
D
E
S
C
5904 5720 5719 4086 5723 391 2270 6812 300 4512 7598
BU/VT BN/BK BU/BK YE/BU BU/GN BN/BU GN/WH YE VT/BN GN VT/BU
AS8/ATN/
BTM BTM BTM BTM BTM ATT KI4/KI5 K4C UTT
X1 18 8 20 X4 25 X2 17 12 X5 9 23 14 X7 25 X6 13
K9
Body
Control
Module
X4 5 6 13 X6 6 21 7 12 22 X7 7 10 14 X6 15 5 X5 11 20
Z88 Z88 Z75 Z75/Z88 Z75/Z88 Z75 TB4 TB4 TB4 TB4
7541 7542 6846 3203 3204 58 5356 5357 57 7547 5797 6190 1303 5706 5704
WH/YE GY/YE GN/YE WH/BU BU/VT YE/WH YE/BK VT/YE YE/GY BU/BK YE/BU GY/GN VT/GY GN/BN YE
Door Lock/
Exterior Indicator Release
Lights Schematics Systems
Schematics Schematics
Gateway
The body control module (BCM) in this vehicle functions as a gateway or translator. The purpose of the gateway is to translate serial data messages between the GMLAN high speed bus and the GMLAN low speed bus for
communication between the various modules. The gateway will interact with each network according to that network's transmission protocol.
All communication between the BCM and a scan tool is on the high speed GMLAN serial data circuits. A lost communication DTC typically is set in modules other than the module with a communication failure.
Body Control
The various body control module (BCM) input and output circuits are illustrated in the corresponding functional areas on the BCM electrical schematics. Refer to the Body Control System Schematics for more detailed information.
Circuit Description
There are many components in a vehicle that rely on information from other sources, transmit information to other sources, or both. Serial data communication networks provide a reliable, cost effective, way for various
components of the vehicle to “talk” to one another and share information.
GM uses a number of different communication buses to insure the timely and efficient exchange of information between devices. When compared to each other, some of these buses are different in nature as far as speed, signal
characteristics, and behavior. An example of this is the High Speed GMLAN and Low Speed GMLAN buses.
On the other hand, when other buses are compared to each other they have similar characteristics and simply operate in parallel. In this case they are used to group together components which have high interaction. Examples
are the High Speed GMLAN, Powertrain Expansion, and Chassis Expansion buses. This allows them to communicate with each other on a bus with reduced message congestion insuring faster and the more timely exchange of
information than if all vehicle devices were on a single bus.
The majority of information that exists within a given network generally stays local; however some information will have to be shared on other networks. Control modules designated as Gateway’s perform the function of
transferring information between the various buses. A Gateway module is connected to at least 2 buses and will interact with each network according to its message strategy and transmission models.
GMLAN provides the capability for a receiving device to monitor message transmissions from other devices in order to determine if messages of interest are not being received. The primary purpose is to allow reasonable default
values to be substituted for the information no longer being received. Additionally, a device may set a Diagnostic Trouble Code to indicate that the device it is expecting information from is no longer communicating.
The High Speed GMLAN serial data network consists of two twisted wires. One signal circuit is identified as GMLAN-High and the other signal circuit is identified as GMLAN-Low. At each end of the data bus there is a 120 Ω
termination resistor between the GMLAN-High and GMLAN-Low circuits.
Data symbols (1’s and 0’s) are transmitted sequentially at a rate of 500 Kbit/s. The data to be transmitted over the bus is represented by the voltage difference between the GMLAN-High signal voltage and the GMLAN-Low signal
voltage.
When the two wire bus is at rest the GMLAN-High and GMLAN-Low signal circuits are not being driven and this represents a logic “1”. In this state both signal circuits are at the same voltage of 2.5 V. The differential voltage is
approximately 0 V.
When a logic “0” is to be transmitted, the GMLAN-High signal circuit is driven higher to about 3.5 V and the GMLAN-Low circuit is driven lower to about 1.5 V. The differential voltage becomes approximately 2.0 (+/- 0.5) V.
When MOST receive, transmit, or control line faults are detected, transmit/receive messages will not received as expected from the wakeup request. The A11 Radio and the K74 Human Machine Interface Control Module will then
perform diagnostics to isolate these MOST faults. If the MOST control line is shorted low to 0 V for excess amount of time, the A11 Radio will set a U2098 DTC and K74 Human Machine Interface Control Module will set a
U0029 02 DTC. At this point the MOST bus will be unable to communicate until the shorted MOST control line is repaired.
Once the shorted MOST control line diagnostics pass, the A11 Radio will attempt to resend the initial short pulse attempts up to 3 times on the MOST control line. If the expected responses are not received, the A11 Radio
continues into a failure mode setting a U0028 DTC and will continue on to send one 300 ms long pulse, which will enable the furthest upstream transmitting device to become the surrogate MOST Master in this MOST
fault/diagnostic mode. When the A11 Radio receives this new MOST Master identity, the surrogate MOST master device can be identified based on scan tool data parameter “Surrogate MOST Master Node Upstream Position”.
The scan tool should be used to determine the MOST bus configuration and direction by utilizing the “Last Working MOST ID of Node 1 – 9” parameters from the A11 Radio data display. When a fault is present, it will indicate the
newly enabled “Surrogate MOST Master Node Upstream Position” from the A11 Radio. This will assist in determining where the MOST bus/control is at fault. The MOST device upstream from the surrogate MOST master device,
transmit, receive, or control lines will be the suspect areas for diagnostics at this point. These faults can be associated with any of the MOST transmit, receive, or control line twisted copper wires or possibly an internal device
The K74 Human Machine Interface Control Module will set a U0029 00 DTC when it diagnoses a MOST bus not communicating properly after one attempt. When the DTC U0029 00 is set by the K74 Human Machine Interface
Control Module without the corresponding DTC U0028 from the A11 Radio, it will be an indication of an intermittent wiring/device condition.
The data symbols to be transmitted over the bus are represented by different voltage signals on the bus. When the Low Speed GMLAN Bus is at rest and is not being driven, there is a low signal voltage of approximately 0.2 V.
This represents a logic “1”. When a logic “0” is to be transmitted, the signal voltage is driven higher to around 4.0 V or higher.
• Terminal 11: Object high speed GMLAN serial bus (-) terminal
• Terminal 12: Chassis high speed GMLAN serial bus (+) terminal
• Terminal 13: Chassis high speed GMLAN serial bus (-) terminal
• Terminal 14: High speed GMLAN serial data bus (-) terminal
Depending on the vehicle contents, the K56 Serial Data Gateway Module is gating between primary High Speed GMLAN Bus, Gateway Expansion High Speed GMLAN Bus, Gateway Isolated High Speed GMLAN Bus, and
Chassis High Speed GMLAN Bus. The K56 Serial Data Gateway Module is also gating between primary Low Speed GMLAN Bus and Gateway Isolated Low Speed GMLAN Bus.
Communication between the K56 Serial Data Gateway Module and a scan tool is done through the primary High Speed GMLAN Bus.
B+ L
O
C
X51L X51R
Fuse Block Fuse Block -
- Instrument Instrument D
Panel Left KR76B Panel Right E
KR76A S
Retained C
Retained Accessory
Accessory Power
Power Relay 2 B+
Relay 1
X53A
64 Fuse
Block -
Rear
Body
F30RA
F4DL F4DR F50DR 20A
15A 15A 15A 11
X2 20 X2 10 X1 18
1040 243 143 6040 6040
RD/WH VT/YE VT/YE RD/BU RD/BU
X275 2
143
VT/YE
X300 20 1 2
1040
RD/WH X490 8
X88/Z88 Z75
6040
X307 1 RD/BU
243 143
VT/YE VT/YE
1040
RD/WH
-DT4 DT4
A A A A A A
X80G E32 X80L X80D X80RL X80RR
Accessory Cigarette Accessory Accessory Accessory Accessory
Power Lighter Power Power Power Power
Receptacle - Receptacle Receptacle - Receptacle - Receptacle - Receptacle -
Instrument Center Center Rear Rear
C Panel C Console Rear C Console C Compartment C Compartment
Compartment Left Right
C
1050 1050 1050 1050 1150 1450
BK BK BK BK BK BK
B+ L
O
C
X51L X51R
Fuse Block Fuse Block -
- Instrument Instrument D
Panel Left KR76B Panel Right E
KR76A S
Retained C
Retained Accessory
Accessory Power
Power Relay 2 B+
Relay 1
X53A
64 Fuse
Block -
Rear
Body
F4DL F50DL F4DR F50DR F30RA
15A 15A 15A 15A 20A
11
X2 20 10 X2 10 X1 18
X275 21 X490 8
X348 9 1
243 143
VT/YE VT/YE
A A A A A A
E32 X80G X80D X80E X80RL X80RR
Cigarette Accessory Accessory Accessory Accessory Accessory
Lighter Power Power Power Power Power
Receptacle Receptacle - Receptacle - Receptacle - Receptacle - Receptacle -
Instrument Center Center Seat Rear Rear
C Panel C Console C C Compartment C Compartment
Compartment Left Right
C
L
O
B+ C
X51R
Fuse Block - D
E
F39DR Instrument S
C
25A Panel Right
Auxiliary
Battery X2 35
Schematics
K9
F38DR Body 4140
Control RD/GY
Module
5W4/9C1
X5 14
300 300
VT/BN VT/BN
6
T1
B+ Accessory DC/
X1 33 AC Power
Inverter Module
X61A
Junction
Block -
Instrument
Panel
110V AC
X5 18 12 3 7 10 11
NQH
X300 25 26 X306 1 2 3
Transfer Case
Control
Schematics
X1 1 X2 1 X1 3 X2 3
X81
Accessory W7
Power Blunt Cut -
Receptacle - Shield
110V AC
G210
L
O
B+ C
X51R
Fuse Block - D
E
F39DR Instrument S
C
25A Panel Right
Auxiliary
Battery X2 35
Schematics
K9
F38DR Body 4140
Control RD/GY
Module
5W4/9C1
X5 14
300
VT/BN 300 6
VT/BN
T1
B+ Accessory DC/
X1 33 AC Power
Inverter Module
X61A
Junction
Block -
Instrument
Panel
110V AC
X5 18 12 3 7 10 11
NQH
300
VT/BN
Transfer Case
Control 6087 5683 5684 514 1050
Schematics BU/BN BK RD BK/WH BK
300
VT/BN
X1 1 X2 1 X1 3 X2 3
X81
Accessory W7
Power Blunt Cut -
Receptacle - Shield
110V AC
G210
B+ L
O
C
X51R
Fuse Block -
F39DR Instrument D
E
25A Panel Right S
C
Auxiliary X2 35
Battery
Schematics 4140
K9 RD/GY
F38DR Body
Control
Module X305 6
5W4/9C1
X5 14 4140
RD/GY
300
VT/BN 300 6
VT/BN
T1
B+ Accessory DC/
X1 33 AC Power
Inverter Module
X61A
Junction
Block -
Instrument
Panel
220V AC
X5 18 12 3 7 10 11
Transfer Case
Control
Schematics 6087 5683 5684 514 1050
BU/BN BK RD BK/WH BK
X300 25 26 X306 1 2 3
X1 1 X2 1 X1 3 X2 3
X81B
Accessory W7
Power Blunt Cut -
Receptacle - Shield
220V AC
G210
B+ L
O
C
X51R
Fuse Block -
F39DR Instrument D
25A Panel Right E
S
C
Auxiliary X2 35
Battery
Schematics
4140
K9 RD/GY
F38DR Body
Control
Module X305 6
5W4/9C1
X5 14 4140
RD/GY
300
VT/BN
300 6
VT/BN
T1
B+ Accessory DC/
X1 33 AC Power
Inverter Module
X61A
Junction
Block -
Instrument
Panel
220V AC
X5 18 12 3 7 10 11
NQH
300
VT/BN
300 6087 5683 5684 514 1050
VT/BN BU/BN BK RD BK/WH BK
Transfer Case
Control
Schematics
X305 12 2 7 10 11
X1 1 X2 1 X1 3 X2 3
X81B
Accessory W7
Power Blunt Cut -
Receptacle - Shield
220V AC
G210
L
O
X51L C
Fuse Block
- Instrument
KR76A Panel Left D
Retained Accessory E
S
Power Relay 1 C
F8DL K9
10A Body
Control
Module
X1 44 X7 25
43 4512
VT/YE GN
X225 7 23
43 4512
VT/YE GN
X300 7 29
43 4512
VT/YE GN
X313 1 3
43 4512
VT/YE GN
1 3
T22
IGN Mobile Device
Wireless
Charger
Module
2
1050
BK
G210
K9
Body
Control
Module
T22 K74
Mobile Device Human
Wireless Machine
Charger Interface
Module Control
Module
P17
Info
Display
Module
The Mobile Device Wireless Charging System (WCS) is an system for wirelessly charging mobile devices. It is capable of charging the batteries of compatible mobile devices. A compatible device is one that is compliant with
Power Matters Alliance (PMA) or Wireless Power Consortium (WPC) Standard, meaning that it is equipped with a PMA or WPC wireless charge “receiver” that will work with the charge “transmitter” installed in the vehicle. The
devices may utilize built-in charging circuitry or an adapter (external plug-in device which contains the charging circuitry). To check for phone or other device compatibility, refer to GM Total Connect.
Warning: Remove all objects from the charging pad before charging your mobile device. Objects, such as coins, keys, rings, paper clips, or cards, between the phone and charging pad will become very hot.
On the rare occasion that the charging system does not detect an object, and the object gets wedged between the phone and charger, remove the phone and allow the object to cool before removing it from the
charging pad, to prevent burns.
Charging
To charge a device, place it on the charging surface in the vehicle. There is a charging coil located in the center of the charging surface. The device has a charging coil typically near the center of the device. These coils must
be lined up in order for charging to proceed. When the interruptible retained accessory power (IRAP) relay is closed (this is true typically when vehicle ignition is in Run or Accessory position), the WCS will detect the device,
establish communications with the device to confirm it is a compatible device, and then deliver charging power to the device via wireless interface. The WCS will be able to deliver up to 5W of power to compatible devices. It
shall only enter a charging state if communication is established and a compatible device is identified.
The WCS shall not enter a charging state if there is no communication established with a compatible device. If a non-compatible device or metallic foreign object is detected, the WCS will not transfer power. The charger monitors
its internal temperature and will shut down if the charger temperature exceeds 185F (85C).
Indicator
The body control module will detect the device battery is charging and send a serial data message on the GMLAN bus to the radio display. The radio display will indicate a device is currently charging. When the indicator is
toggling on and off this indicates a thermal limit has been reached and the device will not charge. For more information refer to the infotainment owners manual.
T1
Accessory DC/
AC Power
Inverter Module
X81
Accessory
Power
Receptacle -
110V AC
The alternating current (AC) accessory power outlet system consists of the accessory DC/AC power inverter module and the accessory power receptacle – 110 V AC. The accessory DC/AC power inverter module converts 12 V
direct current (DC) battery power to 110 V at 60 Hertz (Hz) AC power to operate AC powered devices. The accessory DC/AC power inverter module provides up to 150 watts of power. The accessory power receptacle – 110 V AC
provides the usual connection for AC powered devices.
T1
Accessory DC/
AC Power
Inverter Module
X81B
Accessory
Power
Receptacle -
220V AC
The alternating current (AC) accessory power outlet system consists of the accessory DC/AC power inverter module and the accessory power receptacle – 220V AC. The accessory DC/AC power inverter module converts 12 V
direct current (DC) battery power to 220–230 V at 50 Hertz (Hz) AC power to operate AC powered devices. The accessory DC/AC power inverter module provides up to 150 watts of power. The accessory power receptacle – 220V
AC provides the usual connection for AC powered devices.
Items
1. X125
Items
1. X139
2. X110
3. J130
5. J115
Items
1. X100
2. X120
3. X122 (6J7)
4. X150
5. J125
Items
1. X150
2. X185
3. X115
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
A
B 2 3 4 5
C 1 6
J 7
K 8
L 14 13 12 11 10 9
O
15
P
Items
1. J126
3. J152 (K59)
4. J153 (K59)
5. J161
6. X115
7. J165
8. X139
10. X125
11. J127
15. X154
Items
2. J161
4. X175 (M5U)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
A
B 3 4
C 2
D 1
H 7
I 6
J 5
Items
1. X115
2. J165
3. J123 (L96)
4. X171 (L96)
5. X125
6. J127
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
A
1 2
D
3
E
6
M
5
N
4
O
Items
1. J258
2. X215
3. J255
4. X217
5. X216
6. J257
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
A
B 1 2 3
J 6 5 4
Items
1. X302 (D07)
2. X303 (D07)
4. X271 (WX7)
6. X300 (D07)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
A
B 1 2 3 4 5 6 7 8 9 10 11 12
C 13
D 14
E 15
F 16
G 17
H 18
K 25 24 23 22 21 20 19
L
Items
1. J242
2. X222 (UE1)
3. X215
4. X205
7. J212 (Z75)
8. J211
9. J205
11. X203
12. J201
13. J200
14. J210
15. X201
17. J208
18. J208
19. X225
20. J294
21. J220
22. J249
23. J251
24. X275
Items
1. J285
2. J295
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
A
C 2
E 1
G 3
J 6 4
K 5
Items
3. X313 (DCK)
4. X300 (D07)
5. X304 (AZ3)
Items
1. X313 (DCK)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
A
B 1
D 2 3 4
E 5
Items
1. X313 (DCK)
4. X304 (AZ3)
5. X300 (D07)
Items
1. X318
Items
2. X324 (CF5)
3. J303
4. J302
5. X316
6. J301
7. J333
Items
1. X700
3. J331
5. X310
6. J306
7. J308
9. X500
12. J289
14. X119
15. X225
17. J350
18. J384
21. J386
22. J383
23. J361
25. J353
Items
1. X216
2. X217
3. X600
4. X275
5. JX300 (UD5)
6. J369
7. X320
9. X800
14. J371
17. J363
18. J368
19. J365
Items
1. X510
2. X500
3. J515
4. J520 (Z75)
5. J518 (HD7)
6. J519
7. J516
8. X505
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
A
2 3 4 5
B
1
C
D
6
E
G
8 7
H
Items
1. J314
2. J315
3. J313
4. J317 (KB6)
5. J316 (KB6)
6. X310
7. X312
Items
1. J620 (Z75)
2. J616
3. X605
4. J611 (HD7)
5. J615
6. X600
Items
1. X700
2. J715
3. J710 (UQH)
4. J711 (UQH)
5. J116 (Z75)
6. J720 (Z75)
7. X705 (Z75)
Items
1. J820 (Z75)
2. J816 (Z75)
3. X805 (Z75)
4. J811 (UQH)
5. J810 (UQH)
6. J815
7. X800
Items
Items
1. X340 (AS8)
2. X338 (AS8)
Items
1. X338 (AS8)
2. J351 (BTM)
5. J354
Items
1. X490
2. X380
3. J462 (UQS)
4. J461 (UQS)
Items
1. J402
2. X487
4. X390
6. X900
7. X490
8. X495
Items
1. J901
2. X900
3. J902
5. J904
Items
1. X204 (U42)
2. X203
4. X316
5. J332
6. J312
7. J320 (AZ3)
8. J313
9. J311
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
A
B 2
1
C
E 3
F 4
H 6 5
J 7
K 8
L 9
M 10
N 12 11
O 14 13
Items
1. X420
3. J453
4. X410
7. J375
8. J355
9. J356
11. J191
12. X185
13. X125
14. X182
Items
1. X495
6. J498 (UKC)
7. J493 (T79)
Items
1. X495
5. J493 (T79)
6. J498 (UKC)
L
O
C
D
E
S
C
1
RD
+ X6 A
C1 X50D
Battery Fuse
Block -
L83/L86 L96 Battery
-
F4UD F3UD F2UD F2UD F1UD F7UD F8UD
175A 125A 175A 250A 100A 60A 60A
X5 A X4 A X3 - A X2 A X1 A X7 2 1
(Not Used)
L83/L86 5W4/9C1
842
RD/VT
X183 1
2 2 242 842 242 142
RD/YE RD/YE RD/GN RD/VT RD/GN RD/GY
842
RD
X2 A X5 1 X2 A X6 A X2 P X1 21 24
L
O
C
D
E
S
C
+
C1B X50E
Battery - Fuse Block
Auxiliary F1UE F2UE - Battery
100A 50A Auxiliary
X1 A X2 A
X3 A X1 A
KR79 X53A W9
Auxiliary Fuse Blunt Cut -
Battery Block - Police
Relay 2 Rear Provision
Body
L
B+ O
C
X50A
Fuse Block -
Underhood D
E
F1UA F2UA F3UA F4UA F5UA F6UA F10UA F13UA F14UA F17UA F21UA F23UA F24UA F25UA F26UA F36UA S
30A 60A 60A 40A 40A 30A 40A 60A 60A 40A 15A 10A 30A 30A 5A 25A C
L96
KR3
F35UA F36UA F67UA F102UA F103UA F109UA F116UA F123UA F104UA F22UA Horn
25A 30A 30A 15A 10A 10A 40A 40A 40A 20A Relay
30 30
KR27 KR23A F93UA
Starter Fuel 15A
Relay Pump
Relay
X5 - G5
(Not Used)
(T4F) (T3U)
KR49 KR48 KR46 KR61 KR63L KR63R
Headlamp Headlamp Front Fog Trailer Trailer Trailer
Low Beam High Beam Lamp Backup Stop/Turn Stop/Turn
Relay Relay Relay Lamps Signal Signal
Relay Lamp Lamp
Relay - Relay -
Left Right
30 86
KR53 KR11 KR6 F30UA
Park Windshield Rear 25A
Lamps Washer Window
Relay Pump Relay Washer
Pump
87 Relay
A KR12C KR12B
F42UA F43UA F41UA F114UA F115UA Windshield Windshield
15A 15A 20A 15A 15A Wiper Wiper
B+ Speed Relay
Bus Control
Relay
L
O
C
X50A
B+ Fuse Block - D
Bus Underhood E
S
A C
30 5W4/9C1 5W4/9C1
KR73
Ignition F78UA F70UA
Main 5A 5A
Relay
87
30
F45UA F75UA F107UA KR23B
10A 10A 10A Fuel Pump
Relay -
Secondary
85 30 85 30 85 30 85 30
KR161A KR161B KR161C KR161D
Configurable Configurable Configurable Configurable
Provision Provision Provision Provision
Relay 1 Relay 2 Relay 3 Relay 4
87 87 87 87
F63UA F28UA F44UA F47UA
30A 30A 30A 30A
86 30
KR75 F60UA
Engine 10A
Controls
Ignition Relay
87
86 30
KR29
A/C
F87UA F88UA F89UA F90UA F91UA F100UA F101UA Compressor
15A 20A 20A 15A 15A 15A 30A Clutch Relay
X4 - M4
(Not Used)
L
O
B+ C
X50A
Fuse Block - D
B+ E
Underhood S
Bus C
F1UA F2UA F35UA F10UA F23UA F25UA F3UA F13UA F14UA F4UA F17UA F6UA
30A 60A 25A 40A 10A 30A 60A 60A 60A 40A 40A 30A
X5 C2 B1 J4 E1 G4 G2 X4-G5 X4 B2 E2 E1 B1 X3 E2 B1
(Not Used)
1142 442 1640 1642 2040 1940 842 42 942 1042 4042 1342 1342
RD/YE RD/YE RD/VT RD/WH RD/WH RD/VT RD/VT RD/BU RD/WH RD/GY RD/WH RD/GY RD/GY
X115 1
X2 3
X61A
Junction
Block -
Instrument
Panel
X9 11
1342 1342
RD/GY RD/GY
X1 5 1 25 A 1 1 X1 21 23 64 4 4 B X3 C
K4 K17 K83 K38 K111 X51L X53A M101R M101L A16 K69
Assist Electronic Park Chassis Fuel Pump Fuse Block Fuse Seat Belt Seat Belt Transfer Transfer
Step Brake Brake Control Driver - Instrument Block - Retractor Retractor Case Case
Control Control Control Module Control Panel Left Rear Motor Motor Motor Control
Module Module Module Module Body Module - Module - Module
Right Left
L
O
C
X50A
B+ Fuse Block - D
Underhood E
S
C
B+
Bus
F26UA F36UA F21UA F24UA F67UA F103UA F102UA F109UA F116UA F123UA
5A 30A 15A 30A 30A 10A 15A 10A 40A 40A
X2-L6 X4 M1 H5 X5 J2 G6 G3 N2 X2-N1 X2 G6 H5 G5 X5 H3 X1 G5 E2 B2
(Not Used) (Not Used)
2340 242 242 2440 2440 742 3440 440 1840 1840 3940 342 642
RD/YE RD/GN RD/GN RD/GN RD/GN RD/GN RD/WH RD/BN RD/GN RD/GN RD/BU RD/WH RD/GY
E X158 3 X122 C
X88 X1 20 (L96)
X2 35 Trailer X1 52 (L83/L86) 2
X61A Connector
Junction
Block -
Instrument
Panel
X6 C K20 Q13
Engine Evaporative
Control Emission
-JL1 Module Vent
Solenoid
Valve
242 3440
RD/GN RD/WH
B
MYC/MYD M5U
Q4 4
Vehicle
Level Q8
X4 20 1 Control 32 30 Control 66 2 2
Solenoid Solenoid
Valve Valve
Assembly
L
O
B+ C
X50A
Fuse Block - D
B+ E
Underhood S
Bus C
30
KR73
Ignition
Main
Relay
87
4 KR73
BUS
L96
F5UA F45UA F75UA F76UA F68UA F74UA F107UA
40A 10A 10A 15A 20A 15A 10A
30
KR23B
Fuel Pump
Relay -
Secondary
X3 B2 X5 K1 X3 M8 X2 L7 M7 (L96) X5 J5 X5 - G2
(Not Used)
A2 (L83/L86)
Z85/Z95 Z85 5W4/9C1 NP0/NQH L83/L86 JL1/Z85
W9 X111 3
Blunt Cut -
X185 33 Police 2139
Provision VT/BK
1842
RD/BU
MYC/MYD M5U
12
Q8 X1 19 (L96)
30 86 Control 35 1 X1 51 (L83/L86) 6 25
Solenoid
Valve
Assembly
L
O
B+ C
X50A
Fuse Block - D
B+ E
Underhood S
Bus C
5W4/9C1 5W4/9C1
F78UA F70UA
5A 5A
KR73 4
BUS
5W4/9C1 5W4/9C1
F77UA F69UA
5A 5A
85 30 85 30 85 30 85 30
KR161A KR161B KR161C KR161D
Configurable Configurable Configurable Configurable
Provision Provision Provision Provision
Relay 1 Relay 2 Relay 3 Relay 4
87 87 87 87
X3 M7 X4 G2 K5 K2
X1 16 31 35 48
X61A
Junction
Block -
Instrument
Panel
X7 20 14 4 1
W9
Blunt Cut - Police
Provision
L
O
B+ C
X50A
Fuse Block - D
B+ E
Underhood S
Bus C
86 30
KR75
Engine Controls
Ignition Relay
87
B KR75
Bus
F87UA F88UA F101UA F89UA
15A 20A 30A 20A
X5 M7 X2 J2 J3 H2 K3 G4 K5 J4 K4
FHS
5294 5294 5291 5291 5291 5291 5291 5290 5292 5292 5292 5292 5292
VT/BU VT/BU VT/BU VT/BU VT/BU VT/BU VT/BU VT/BU VT/BU VT/BU VT/BU VT/BU VT/BU
1 5 4 4 4 4 X1 62 73 67 4 4 4 4
B198 B75C T8A T8C T8E T8G K20 T8B T8D T8F T8H
Fuel Multifunction Ignition Ignition Ignition Ignition Engine Ignition Ignition Ignition Ignition
Composition Intake Air Coil 1 Coil 3 Coil 5 Coil 7 Control Coil 2 Coil 4 Coil 6 Coil 8
Sensor Sensor Module
L
O
B+ C
X50A
Fuse Block - D
B+ E
Underhood S
Bus C
86 30
KR75
Engine Controls
Ignition Relay
87
B KR75
Bus
F87UA F88UA F101UA F89UA
15A 20A 30A 20A
X5 - M7 X2 J2 H2 K3 X2 - J3 X2 J6 J4 K5 X2 - K4
(Not Used) (Not Used) (Not Used)
J149 J148
5 A A A A X2 28 A A A A
X170 H X171 H
B75C Q17A Q17C Q17E Q17G K20 Q17B Q17D Q17F Q17H
Multifunction Fuel Fuel Fuel Fuel Engine Fuel Fuel Fuel Fuel
Intake Air Injector 1 Injector 3 Injector 5 Injector 7 39 Control Injector 2 Injector 4 Injector 6 Injector 8 39
Sensor PK Module PK
J160 J164
39 39 39 39 39 39 39 39
PK PK PK PK PK PK PK PK
D D D D D D D D
L
O
X50A C
Fuse Block -
KR75 Underhood
Bus B D
E
F91UA F90UA F100UA S
15A C
15A 15A
X2 J6 J5 G3 H3
J163
L83/L86 L96
X139 5
5290 5293
VT/BU VT/BU
X125 4 X154 7
X106 2
5290
VT/BU
2 2 2 2
1 X2 28 1 4 1
L
O
B+ C
X50A
Fuse Block - D
B+ E
Underhood S
Bus C
T4F T4F
KR49 KR48
Headlamp Headlamp
Low Beam High Beam
Relay Relay
X1 A2 J4 H4 5
X122 B D
711 311
WH WH
X110 2 3 X120 3 2
E13LA E13RA
712 711 Headlamp 311 312 Headlamp
PU WH Assembly - PU YE Assembly -
Left Right
L
O
B+ C
X50A
Fuse Block - D
B+ E
Underhood S
Bus 86 C
30
KR53
Park
Lamps
Relay
87
X5 K2 X1 G1 F1 X5 K4 J3
-Y91 -Y91
X410 5 X420 5
YE YE
X110 7 6 X120 6 7 F
X88
E42L E13LA E13RA E42R Trailer
Tail Lamp Headlamp Headlamp Tail Lamp Connector
Assembly - Assembly - Assembly - Assembly -
Left 709 709 Left 309 309 Right Right
BU GN GN BU
L
O
B+ C
X50A
Fuse Block - D
B+ E
Underhood S
Bus 86 C
30
KR53
Park
Lamps
Relay
87
X5 K2 X1 G1 F1 X5 K4 J3
X410 5 X420 5
YE YE
X110 7 X120 7 F
X88
E42L E13LA E13RA E42R Trailer
Tail Lamp Headlamp Headlamp Tail Lamp Connector
Assembly - Assembly - Assembly - Assembly -
Left 709 Left 309 Right Right
BU BU
L
O
B+ C
X50A
Fuse Block - D
B+ E
Underhood S
Bus 86 C
30
KR53
Park
Lamps
Relay
87
X5 K2 X1 G1 F1 X5 K4 J3
X100 9 24
YE YE
E5E E5F
Tail Tail
Lamp - Lamp -
Left K166L K167L K167R K166R Right
Multifunction Multifunction Multifunction Multifunction
LED Control LED Control LED Control LED Control
Module - Left Module - Module - Module - Right
Headlamp Front Fascia Front Fascia Headlamp
Left Right
L
O
B+ C
X50A
Fuse Block - D
B+ E
Underhood S
Bus C
KR61 KR63L KR63R
Trailer Trailer Trailer
Backup Stop/Turn Stop/Turn
Lamps Signal Signal
Relay Lamp Lamp
Relay - Relay -
Left Right
X4 A3 X5 C1 M8 K5 K6
DD8
-UVC UVC
J386 J453
24 24
GN/WH GN/WH X88/Z88 Z75 X88/Z88 Z75
X900 36
24 24 24 24 24
X2 15 GN/WH GN/WH GN/WH GN/WH GN/WH
X61A
Junction A G D
Block - X410 1 1 X420 1 1
Instrument X88
Panel Trailer
24 24 24 24 Connector
X3 13 PU (X88) BK PU (X88) BK
24 24
24 WH (Z88) WH (Z88)
GN/RD
3
E42L E42R
Tail Lamp Tail Lamp
24 Assembly - Assembly -
GN/WH Left Right
1
L
O
B+ C
X50A
Fuse Block - D
B+ E
Underhood S
Bus C
T3U T3U
X1 F2 D2 J2 J3
X100 3
2234
BN/VT
J101
2234 2234
BN/VT BN/VT
1 1 2 A A
E29LF E29RF
Fog Fog
Lamp - Lamp -
G24 G19 P12 Left Front Right
Windshield Rear Horn Front
Washer Window
Pump Washer
Pump
L
B+ B+ O
C
X51L
Fuse Block
- Instrument D
E
Panel Left S
C
F16DL F17DL F18DL F19DL F20DL F26DL F7DL F10DL F11DL F42DL F43DL F44DL
2A 10A 10A 10A 15A 15A 10A 20A 10A 30A 30A 30A
F34DL
15A
30
KR87 KR73
Transmission Ignition
Park Position Main
Relay Relay
87A 87
KR1F KR1R
Adjustable Adjustable F38DL F33DL F36DL F37DL F24DL F25DL
Pedal Pedal 10A 15A 10A 7.5A 15A 10A
Relay - Relay -
Forward Rearward
L
O
C
B+
D
X51L E
B+ Fuse Block S
- Instrument C
Bus
Panel Left
F16DL F28DL F29DL F17DL F18DL
2A 10A 10A 10A 10A
X2 5 25 X1 14 2 3 16
1940
RD/VT
X201 4 X505 22
X316 15
J519
12 (-A45)
4 X1 1 X2 1 2 3 2 X2 1 4 10 (A45)
L
O
C
B+
D
X51L E
B+ Fuse Block S
- Instrument C
Bus
Panel Left
F47DL F46DL F20DL F27DL
15A 15A 15A 10A
X1 18 17 1 5 X2 26
1140
RD/BN
ULT ULT
J385
A45 AG2
16
X84
X310 47 X320 47 17 13 X310 8 23 X320 23 Data Link
Connector
5140 6140 2240 2240
RD/GN RD/GN RD/BN RD/BN
KA1 KB6
5140 5140 5140 6140 6140 6140 2240 2240 2240 2240 1140 1140
RD/GN RD/GN RD/GN RD/GN RD/GN RD/GN RD/BN RD/BN RD/BN RD/BN RD/BN RD/BN
K55D K53D K29 K55P K53P K134P S64P K134D S64D K40D K40P
Seat Blower Seat Blower Seat Seat Blower Seat Blower Seat Bolster Seat Seat Bolster Seat Seat Seat
Assembly - Assembly - Heating Assembly - Assembly - Memory Adjuster Memory Adjuster Memory Memory
Driver Driver Back Control Passenger Passenger Control Switch - Control Switch - Control Control
Cushion Module Cushion Back Module - Passenger Module - Driver Module - Module -
Passenger Driver Driver Passenger
B+ B+ L
O
C
X51L
B+ Fuse Block
Bus - Instrument D
Panel Left E
S
B+ C
Bus
F10DL F11DL F19DL F26DL F39DL F34DL
20A 10A 10A 15A 10A 10A
KR87
Transmission
Park Position
X2 8 7 18 27 14 35 Relay
X1 20 28
J220
JF4-A45 JF4-A45
A A
A20 A22 A26 P16 P29 2840 2840 5130 5129
4140 Radio/HVAC Radio HVAC Instrument Head-Up RD/GY RD/GY GN/VT YE
4640 Controls Controls Controls Cluster Display
RD/VT RD/GY
X1 3 X2 3 1 1 5 1 4 1 4
M5
X1 1 Adjustable
Pedal
Motor
B+ L
O
X51L C
Fuse Block
B+ - Instrument D
Bus Panel Left E
S
30 C
KR73
Ignition
Main
Relay
87A 87
X2 36 37 X1-29 X2 15 34 X1 30 X2 38 X3 13 X1 32 X2 28 X3 14
(Not Used)
1139
RD 6
W9
Blunt Cut -
Police 1739
Provision VT/GN
3 X2 9 4 X2 4 X1 2 1 2 X1 8 1 4
K60 K32 K33 K175 K69 K188 A34 A10 B87 P16 P43 P14
Steering Steering HVAC Center Transfer Human HVAC Inside Rearview Instrument Collision Alert Passenger
Column Wheel Control Console Case Machine Controls - Rearview Camera Cluster Indicators Air Bag
Lock Heating Module Compartment Control Interface Auxiliary Mirror Disabled
Module Control Cooler Module Control Indicator
Module Control Module
Module Bypass
Module
L
B+ O
C
X51L
B+ Fuse Block
Bus - Instrument D
E
30 Panel Left S
KR76A C
Retained
F12DL F7DL F44DL F43DL F6DL F5DL Accessory
2A 10A 30A 30A 50A 50A Power
Relay 1
87
F8DL
10A
F4DL F50DL
15A 15A
X2 3 4 X3 12 X1 27 36 37 X2 20 10 X3 11 X1 44
X316 17
X310 2 X500 1 X700 1 D07 DT4-D07 -D07/DT4 K4C 5W4/9C1
X300 20 X316 23
6817 6136 240 5040 1040 43
YE BN RD/YE RD/YE RD/WH VT/YE
CF5 X225 7 W9
Blunt Cut - Police
Provision
Interior Lights X88/Z88 Z75 43 43
Dimming VT/YE VT/YE
Schematics X307 1 X2 50
X61A
X300 7 Junction
1842 1842 1040 Block -
RD/BU RD/BU RD/WH Instrument
43 Panel
VT/YE X3 - 48 X7 8
(Not Used)
UG1 TRW -A45 A45/ULT X324 6 X313 1
S25 S63 S64D K40D M74D S79LR X80G E32 X80G M69 T22 KR103 W9 K127
Garage Roof Seat Seat Window Window Accessory Cigarette Accessory Sunroof Mobile Device DVD Relay Blunt Cut - Communication
Door Beacon Adjuster Memory Motor - Switch - Power Lighter Power Motor Wireless Police Interface
Opener Switch Switch - Control Driver Left Rear Receptacle - Receptacle Receptacle - Charger Provision Module -
Driver Module - Instrument Instrument Module WLAN Router
Driver Panel Panel
L
O
C
D
E
S
C
B+ B+
X51R
Fuse Block -
Instrument
Panel Right
F8DR
10A 30
F46DR F47DR F48DR F49DR KR76B
15A 15A 30A 30A Retained
Accessory
KR147 Power
Instrument Relay 2
Panel
87
Compartment
Door Unlatch
Actuator
Relay F50DR F4DR
15A 15A
L
B+ B+ O
C
X51R
B+ B+ Fuse Block -
Instrument D
Bus Bus E
Panel Right S
C
F13DR F19DR F38DR F47DR F46DR F39DR F36DR F37DR F45DR F48DR F49DR
20A 20A 10A 15A 15A 25A 30A 15A 40A 30A 30A
X2 7 8 29 X1 34 33 X2 35 38 X2 - 42 X1 - 28 X1 22 37 38
(Not Used) (Not Used)
4040 2540 2240 5140 3440 4140 2340 542 3740 1440
RD/VT RD/BU RD/BN RD/GN RD/WH RD/GY RD/YE RD/VT RD/YE RD/BN
X4 31
X61A
Junction
Block -
Instrument
Panel
X7 - 17 X7 7
(Not Used)
X217 1 X320 2
X55X
Fuse
KI4 KI5 Holder - X 5A -ULT ULT
Video
Display Y
X305 6
4140
RD/GY RD
X2 4 X1 2 4 X5 3 4 6 A2 1 1 X1 4 10 X1 2
L
O
B+ C
X51R D
B+ Fuse Block - E
Bus Instrument S
F12DR F20DR F21DR C
Panel Right
2A 10A 30A
X2 16 1 X3 - 3 X3 1
(Not Used)
3040
RD/YE 1540 3140
RD/GN RD/GN
X201 25
X319 1
3040
RD/YE 3140
RD/GN
X1 1
X85
Steering Wheel Air U42-Z75 Z75 TRW CF5
Bag Coil
1540
RD/GN
X2 10
3040
RD/YE (X88/Z88)
J212
3040
RD/GY (Z75)
U42 Z75 Z75 Z75
1540
RD/GN
-UK3/Z75 UK3/Z75
X203 5
3040 3040
RD/YE (X88/Z88) RD/YE (X88/Z88)
L
B+ O
C
X51R
B+ Fuse Block -
Instrument D
Bus E
F27DR F28DR F29DR Panel Right S
10A 10A 20A C
X1 - 44 X1 42 27 X2 - 25 X1 43 X2 17
(Not Used) (Not Used)
AZ3
340
RD/VT
840 840 340 3140
RD/BU RD/BU RD/VT RD/GN
X1 15 X600 11 X348 14
J403
340 340 340 340 340
3140 RD/VT RD/VT RD/VT RD/VT RD/VT
UFL/UHX/UGN+Z75 UGN K59 RD/GN
X495 22 X300 24 42
X318 1 X605 22
3140 3140 3140 3140 3140
RD/GN RD/GN RD/GN RD/GN RD/GN
X2 5 340 340 340
X61A RD/VT RD/VT RD/VT
840 840 Junction
RD/BU RD/BU Block - TC2-UKC TC2/UKC
Instrument X150 23
Panel J492 Z75 X88/Z88
X3 3
3140 3140 3140 3140 X307 7
RD/GN RD/GN RD/GN RD/GN
340
RD/VT
16 (A45) 2 (UGN+Z75)
1 4 (-A45) 6 3 (UFL/UHX) X1 1 1 X1 2 8 X1 1 X3 8 X1 7 10 X1 6 X1 6 X1 6
B200 S79P X83 B174W K124 K14 K171 B218R K182 A11 K74 A33 X82 X92 X83
Rain Window Auxiliary Frontview Active Distance Hands-Free Side Object Parking Radio Human Media Disc Audio/ USB Auxiliary
Sensor Switch - Audio Camera - Safety Sensing Liftgate Sensor Assist Machine Player Video Receptacle Audio
Module Passenger Input Windshield Control Cruise Sensor Module - Control Interface Input Input
Module Control Control Right Module Control Adapter
Module Module Module
L
B+ O
C
X51R
B+ Fuse Block - D
Bus Instrument E
30 Panel Right S
C
KR76B
Retained
Accessory
Power
Relay 2
87
F4DR F50DR
15A 15A
X2 10 X1 18
243 143
VT/YE VT/YE
X300 2
X348 9 1
A A A A
L
B+ O
C
X51R
B+ Fuse Block - D
Bus Instrument E
Panel Right S
F8DR F26DR C
F44DR
10A 10A 30A
KR147
Instrument
Panel
Compartment
Door Unlatch
Actuator
Relay
X2 19 34 X1 16 20 19
Z75 UE1
4048
BN
X1 15 1 X1 9 4 8
L
O
C
B+ D
E
S
X50A C
B+ Fuse Block -
Bus Underhood
F14UA
60A
X4 E1
942
RD/WH
X53A
Fuse
Block -
64 Rear
87 Body
F2RA F6RA F10RA F14RA F18RA F21RA F25RA F28RA KR4B
15A 10A 30A 20A 30A 30A Outside
Rearview
Mirror
Heater
Relay
61
42
RD/BU
63
F3RA F7RA F11RA F15RA F19RA F22RA F26RA F30RA KR5
15A 10A 10A 20A 10A 20A Rear
Defogger
Relay
L
B+ O
C
X53A
Fuse
B+ Block - D
Bus E
Rear S
Body C
F2RA F3RA F21RA F28RA F15RA F18RA F30RA
15A 15A 20A 30A 20A 30A 20A
54 55 27 17 37 31 11
X490 7 4 8
J460
X487 1
X900 8
X1 10 1 A A X2 7 3 X1 6 A A
B+ B+ L
O
X53A C
Fuse
B+ Block -
Bus 87 63 Rear D
E
KR4B KR5 Body S
C
F14RA F25RA F7RA F11RA F22RA Outside Rear
10A 30A 10A 10A 10A Rearview Defogger
36 22 49 43 28 Mirror Relay
Heater
1 Relay 62
21 7 3
KR95A KR162 KR57
Liftgate Liftgate Rear Fog 56 F4RA 30 F24RA
Unlatch Window Lamp 15A 30A
Relay Unlatch Relay 57 35
Relay
J379
-UTT UTT
293
A9A A9B BN/VT
Outside Outside
X2 4 3 X1 1 X1 1 X1 1 1
Rearview Rearview
K39 E17D Mirror - E17P Mirror - E18 B159L
Liftgate Outside Driver Outside Passenger Rear Glass
Control Rearview Rearview Defogger Breakage
Module Mirror Mirror Grid Sensor -
Glass - Glass - Left
Driver Passenger
K9 L
F19DL F19DL Body O
Control C
II/III I Module
GN OG
D
X1 20 8 X2 17 X4 25 E
S
C
X1 10
K84
Keyless
Entry
Control
Module
X1 11 12
3558 3559
GN/BK BK/GY
X225 21 13
3558 3559
GN/BK BK/GY
5 2 6 3 7
S38
1300 1300 Ignition
3570 Mode
Switch
3570
ENGINE
START/STOP
1851
BK/WH
G218
B+ L
O
C
X51L K84
Fuse Block Keyless
F16DL - Instrument Entry D
2A Panel Left -BTM 540 Control E
Module S
RD/BU C
6 4 X1 13 5
S39
X2 5 Ignition
X201 4 3 4
Switch VT/BK VT/YE
X225 17 18
III III III III
540
RD/BU I II I II I II I II
3 4
1.3K VT/BK VT/YE
X201 3 24
5 3 2
4 3 3 4
VT/YE VT/BK VT/BK VT/YE
-BTM -BTM -BTM -BTM BTM BTM
1073 1020
WH/BK WH/VT
K9
Body
Control
X3 22 15 5 6 Module
5V
750
X4 22 15
J309
5985 5199
VT/YE J165 GN/VT
5985
VT/YE
L
O
C
K9
Body
Control D
Module E
S
C
L
5199
GN/VT
J308
B+
X4 M5
X50A
85 30 Fuse Block -
KR73 Underhood
Ignition L96
Main
Relay F68UA F45UA F74UA F75UA F76UA F107UA F77UA F69UA
20A 10A 15A 10A 15A 10A 5A 5A
86 87
30 85 85 5199
KR23B KR161A KR161A GN/VT
Fuel Pump Configurable Configurable
Relay - Provision Provision
Secondary Relay 1 Relay 1
85 85
KR161B KR161B
Configurable Configurable
Provision Provision
Relay 2 Relay 2
X2 F2
B+
X1 42
X51L
87A 30 85 Fuse Block
KR73 - Instrument
Ignition Panel Left
F38DL F33DL F36DL F37DL F24DL F25DL
10A Main 15A 10A 7.5A 15A 10A
Relay
87 86
X2 44
550 1850
BK BK
G110 G218
L
K84 O
Keyless C
Entry
Control D
Module E
S
X1 7 C
4083
GY/GN
J351
4083 4083
GY/GN GY/GN
B+ B+
X1 43 X1 6
X51L X51R
Fuse Block Fuse Block -
- Instrument 30 Instrument
30 85 85
Panel Left Panel Right
KR76A KR76B
Retained Retained
F5DL Accessory Accessory
50A Power Power
Relay 1 Relay 2
87 86 86 87
X2 44 X2 22
1850 1050
BK BK
G218 G210
L
O
F46DR K9 C
Body
Control
Module D
E
S
X4 12 C
755
GY/VT
755
GY/VT
B+ B+
X1 43 X1 6
X51L X51R
Fuse Block Fuse Block -
- Instrument 30 Instrument
30 85 85
Panel Left Panel Right
KR76A KR76B
Retained Retained 755
F5DL Accessory Accessory GY/VT
50A Power Power
Relay 1 Relay 2
87 86 86 87
X275 19
F4DL F50DL F8DL
15A 15A 10A F50DR F4DR
15A 15A
755
GY/VT
X2 44 X2 22
X1 2
K188
Human
1850 1050 Machine
BK BK Interface
Control
Module
Bypass
Module
G218 G210
L
O
C
D
E
S
C
+
C1B
Battery -
Auxiliary
350
BK
G100
L
O
C
D
E
S
C
K43
Power
Steering
Control
+ Module
C1
Battery
- X5 2
350
BK
X183 2
L
E13LA O
Headlamp C
Assembly -
E2LF Left
Side E4LF K166L D
E
Marker E4E E4G E4J Turn Multifunction S
Lamp - Headlamp - Headlamp - T7L Park Signal LED Control C
Left Left High Left Low Headlamp Lamp - A90 Lamp - Module - Left
Front Beam Beam Ballast - Left Left Front Logic Left Front Headlamp
J110
150 150
BK BK
X110 1 4
K14
B118B G19 Distance G10L
Windshield G24 Rear Sensing Cooling
Washer Windshield Window X50A Cruise Fan
Fluid Level Washer Washer Fuse Block - P12 Control Motor -
Switch Pump Pump Underhood Horn Module E29LF Left
Fog
Lamp -
Left Front
2 2 2 X1 G4 1 3 B 1
150
BK
150
BK
K59 T3U
J115
150
BK
J114
150
BK
G101
L
E69L E13LA O
Multifunction Headlamp C
Lamp Assembly -
Assembly - Left D
Front Fascia E
Left S
K167L C
Multifunction K166L
LED Control Multifunction
Module - LED Control
E4LF Front Fascia Module - Left
Turn Left Headlamp
Signal
Lamp -
Left Front
J118 J110
X101 1 X110 1 4
X100 25
1 X1 G4 2 2 2 1
J115
150
BK
J114
150
BK
G101
L
E13RA O
Headlamp C
Assembly -
E2RF E4RF Right
Side E4K Turn K166R D
E
Marker E4F E4H T7R Park Signal Multifunction S
Lamp - Headlamp - Headlamp - Headlamp Lamp - Lamp - LED Control C
Right Right High Right Low Ballast - Right A90 Right Module - Right
Front Beam Beam Right Front Logic Front Headlamp
M60A
Active Grille
Air Shutter
1 Motor
Module
4
-T4F T4F -Y91 Y91 X88 TB8/T4F/Z88
250
J120 BK
250 250
BK BK
X120 1 4
G10R
Cooling
Fan B55 250
C1 Motor - Hood Ajar E29RF
Fog BK
Battery Right Switch
Lamp -
3 Right
Front X106 1
X122 A 250
1 C B BK
250 250 250 250 250 250 250
BK BK BK BK BK BK BK
X100 2
250
BK
6J7 T3U
J125
250
L96 BK
G102
L
E69R E13RA O
Multifunction Headlamp C
Lamp Assembly -
Assembly - Right
Front Fascia D
E
K167R Right S
C
Multifunction K166R
LED Control Multifunction
E4RF Module - LED Control
Turn Front Fascia Module - Right
Signal Right Headlamp
Lamp -
Right
Front
7 4 8 3 8 4
X104 1 X120 1 4
250
BK
250
BK
250 250 250 250 G10R
BK BK BK BK Cooling
Fan B55
UVZ -UVZ Motor - Hood Ajar
Right Switch
J103
250
BK
1 C
X100 26 X106 1
UGN/UVZ
J125
250
BK
G102
M75 K9 L
Windshield Body O
Wiper Motor Control C
Module
5 1 X4 26 D
E
S
C
550 95 451
BK YE/BN BK/WH
X3 H2 K3 X4 J6
X50A
KR12C KR61 KR27 Fuse Block -
Windshield Wiper Trailer Starter Underhood
Speed Control Relay Backup Relay
Lamps
Relay
86
KR6 KR73 KR11
KR12B Rear Ignition Windshield
Windshield Window Main Washer
Wiper Washer Relay Pump Relay
Relay Pump
Relay 86
X2 F2 M6
KR81 KR79 K69
Auxiliary Auxiliary Transfer
Battery Battery Case
Relay 1 Relay 2 Control
Module
X1 85 X1 B X3 D
451
5W4/9C1 NP0/NQH NP0/NQH BK/WH
J124 J127
550 451
BK BK/WH
G110
L
O
C
D
E
S
C
+
C1 K9
Battery Body
Control
Module
- X4 26
451 T12
BK/WH K20 B75C
Multifunction Automatic
Engine Transmission
Control Intake Air
Sensor Assembly
X4 J6 Module
X50A Q8
Fuse Block - Control Solenoid
Underhood Valve Assembly
X2 M6 X2 73 7 X1 5
J127
3
G120
L
O
C
D
E
S
E42R C
(T89) (-T89) (T89) (-T89) Tail Lamp
A90 E5R E5AU E4RR E5AV E5B K174R E5F E5B K174R E5F Assembly -
Logic Stop Stop/Turn Turn Stop/Turn Backup Multifunction Tail Backup Multifunction Tail Right
Lamp - Signal Signal Signal Lamp - LED Control Lamp - Lamp - LED Control Lamp -
Right Lamp - Lamp - Lamp - B Right Module - Right Right Module - Right
Right Right Right Right Tail Right Tail
Upper Rear Lower Lamp Lamp
BK BK BK X88 Z88 BK BK BK
J420
2150
BK
X88/Z88 Z75
A6D
Fuel Pump A7
and Level 2150 Fuel Pump
Sensor BK and Level
Assembly - K4 K111 K83 K17 Sensor
Secondary Assist Fuel Pump Park Electronic B20 B198 Assembly
Step Driver Brake Brake Brake Fuel
G12B Control Control Control Control Fluid Level Composition G12
Fuel Pump Module Module Module Module X420 6 Switch Sensor Fuel
- Pump
Secondary
A X1 2 9 H X1 13 38 1 2 A
FHS L96
J356
J355
2150
BK
G121
L
O
C
D
E
S
C
T8A T8C T8E T8G T8B T8D T8F T8H
Ignition Ignition Ignition Ignition Ignition Ignition Ignition Ignition
Coil 1 Coil 3 Coil 5 Coil 7 Coil 2 Coil 4 Coil 6 Coil 8
1 1 1 1 1 1 1 1
J166
350 350
BK BK
G130 G140
M75 L
Windshield O
Wiper Motor C
5 1 D
E
S
C
550 95
BK YE/BN
X3 H2 K3
X50A
KR12C KR61 KR27 KR23A Fuse Block -
Windshield Wiper Trailer Starter Fuel Underhood
Speed Control Relay Backup Relay Pump
Lamps Relay
Relay
86 86
KR6 KR73 KR11 KR23B
KR12B Rear Ignition Windshield Fuel Pump
Windshield Window Main Washer Relay -
Wiper Washer Relay Pump Relay Secondary
Relay Pump
Relay 86 86
X2 F2
K69
Transfer
Case
Control
Module
X3 D
550
Q2 M26 BK
A/C Front Axle T8A T8C T8E T8G T8B T8D T8F T8H
Compressor Engagement Ignition Ignition Ignition Ignition Ignition Ignition Ignition Ignition
Clutch Actuator X9 14 Coil 1 Coil 3 Coil 5 Coil 7 Coil 2 Coil 4 Coil 6 Coil 8
X61A
Junction
Block -
Instrument
Panel
1 4 X2 18 1 1 1 1 1 1 1 1
550 550
BK BK 350 350 350 350 350 350 350 350
BK BK BK BK BK BK BK BK
X111 4 J166 J167
X115 11
J123
G110
K32 E15 L
Steering Steering O
Wheel Wheel X80G C
W11 Heating Heater Accessory
B200 Blunt Cut - Control Power E32
Rain M69 Roof Module Receptacle - Cigarette D
Sensor Sunroof Beacon Instrument Lighter E
1050 1050 S
Module Motor Provision RD/BK (X88/Z88) YE (X88/Z88) Panel Receptacle C
J286
J285
11
X3 10 1050 X5 2
BK 1050 1050
1050 BK BK
KR113 KR114 BK
X2 2
Child Door
Security Dead X85
Lock Disable Lock Steering
Relay Relay Wheel Air KI5 KI4
Bag Coil
X1 9 1050 X305 11
K60 BK
Steering 1050
Column X4 2 BK
Lock
KR76B KR147 Module X300 22
Retained Instrument
Accessory Panel 1050 6 7
Power Compartment BK
1050 1050 1050 1050
Relay 2 Door Unlatch BK BK BK BK
86 Actuator
Relay BTM BTM UVD
J284
X51R X2 22 1050
BK X61A J241
Fuse Block -
Instrument X201 20 1 2
Panel Right M8
Blower
Motor D07 KI4/KI5
1050 1050 1050 1050
BK BK BK BK
6 J242
1050 1050
BK BK
G210
L
O
E37ER C
E37EL Dome/ S43
S51 Dome/ Reading Content B165 D
Telematics Reading Lamps - S45B Theft Content P14 E
Button S12 Lamps - Front Liftgate Deterrent Theft E38 Passenger KR58 S63 S25 K13 S
Assembly S72 Dome Front Overhead Control Sensor Deterrent Flood Lamp Air Bag Roof Roof Garage DVD C
Sunroof Lamp Overhead Console Switch - Disable Sensor - Center Disabled Beacon Beacon Door KR103 Control
Switch Switch Console Left Right Interior Switch Module Console Indicator Relay Switch Opener DVD Relay Module
6 7 1 4 4 1 2 5 2 2 (-DRZ) A1 1 4 A1 X1 1
1 (DRZ)
1050 1050 1050 1050 1050 1050 1050 1050 1050 1050 1050 1050 1050
BK BK BK BK BK BK BK BK BK BK BK BK BK BK BK
J333 J387
1050 E37J
E37B E37C BK E37H Dome/ E31L E31R K127
A10 A34 Dome/ P22A Dome/ P22B Dome/ Reading Sunshade Sunshade B174W Communication W9
Inside HVAC Reading Video Reading Video Reading Lamps - Mirror Mirror Frontview Interface Blunt Cut -
Rearview Controls - Lamps - Display - Lamps - Display - Lamps - Left Right Roof Lamp - Lamp - Camera - Module - Police
Mirror Auxiliary 2nd Row 2nd Row 3rd Row 3rd Row Roof Rail Rail Left Right Windshield WLAN Router Provision
X316 4
5 4 B X2 2 (-ULT) B X2 2 4 4 B B 5 (UGN+Z75) 2
X2 5 (ULT) 1 (UFL/UHX)
1050 1050 -U42 U42 -DNU DNU 1050 1050 1050 1050 1050 1050 750 1050 1050
BK BK BK BK BK BK BK BK BK BK BK
1050 1050
DD8/DL3/DR4 AZ3 BK BK AZ3 AZ3 UFL/UHX/UGN+Z75 ACCESSORY WIFI AYE 5W4/9C1
J332
1050
BK
X3 46 X7 10
X61A
Junction
Block -
Instrument
Panel
X4 16
1050
BK
1
J242
L
O
C
K175 X80D
Center X80L Accessory D
S145 Console E28 Accessory Power T22 E
S
Center Compartment Center Power Receptacle - Mobile Device C
Console Cooler Console Receptacle - Center Wireless
Compartment Control Compartment Center Console Charger
Cooler Switch Module Lamp Console Rear Compartment Module
3 1 2 C C 2
1050 1050
BK BK
X307 10 X313 2
Z75 X88/Z88
1050
X80G BK M91
Accessory Instrument
E1AB E32 Power S77 Panel
Floor Accent Cigarette Receptacle - Transfer Case Compartment X84
Lamp - Right Lighter Instrument Shift Control Door Unlatch Data Link
Front Receptacle Panel Switch Actuator Connector
4
X300 23
B C C 6
1050 1050 1050
BK BK BK
DT4 -DT4 2
J241
1050
BK
J242
S30 X51L L
Headlamp KR76A KR73 Fuse Block O
Switch Retained Ignition - Instrument C
Accessory Main Panel Left
Power Relay
AUTO Relay 1 D
AUTO E
86 86 S
C
KR1F KR1R
Adjustable Adjustable
Pedal Relay - Pedal Relay -
Forward Rearward
8
X1 20 28 X2 44
S48A
Multifunction
Switch - JF4-A45 JF4-A45
OFF Instrument
Panel 5130 5129
GN/VT YE
UFL UHX JHD UD5/UD7 BRS JF4
X2 21 12
8 X61A
Junction
S48C Block -
Multifunction S31D S31P Instrument
A90 Switch 1 - Seat Seat
Logic Panel
Instrument Heating and Heating and
Panel X8 18 16
Cooling Cooling
Switch - Switch -
Driver Passenger 5130 5129
GN/VT YE
5 1
S48D M5
Multifunction M Adjustable
A90 Switch 2 - Pedal
Logic Instrument 4 1 Motor
Panel
1850 1850 4
BK BK
5 K99
X307 9 Steering
Column
K9 M75 Position
Body Windshield Control
Control Wiper Motor Module
Module X3 2
1850 1850
X1 1 X2 2 X6 3 2 BK BK
1850 1850
BK BK X300 9 X201 2
1850 1850 1850 1850 1850 1850 X225 2 28 1850 1850 1850
BK BK BK BK BK BK BK BK BK
X88/Z88 Z75 Z75 1850 1850 (X88/Z88)+(KA1/KB6) N38
BK BK
J205
1850
BK
G218
S3 L
Transmission O
C
Shift Lever
S2A D
M7 Transmission S74 E
B99 Transmission Manual Shift Tow/Haul S
C
S78 Steering Shift Lock B81B Switch - Up/ Mode
Turn Signal/ Wheel Control Park Down Switch
Multifunction Angle Solenoid Position
Switch Sensor Actuator Switch
X1 13 X2 C F X3 2 6 B B C A
J279
K56
Serial Data
S91 Gateway
K33 S38 E1AA Park S27 Module
Floor Accent P43
X84 HVAC A34 Ignition 1851 Brake Collision Alert P29 Head-Up P16
Data Link Control HVAC Controls - Mode Lamp - Left BK/WH Control Head-Up Display Instrument
Front Indicators
Connector Module Auxiliary Switch Switch Display Switch Cluster
5
B
X2 8 4 4 X201 42 8 4 X1 4 2 X1 6 X1 19
1851
BK/WH
X215 9
X300 3
1851 1851 1851 1851 1851 1851 1851 1851 1851 1851 1851 1851
BK/WH BK/WH BK/WH BK/WH BK/WH BK/WH BK/WH BK/WH BK/WH BK/WH BK/WH BK/WH
X4 33 43 34 42 32 41 37 39 38
X61A
Junction
Block -
Instrument
Panel
X4 35
1851
BK/WH
G218
L
O
C
X1 8 X2 5 2 4 2 4 2 2 2 4 2 X2 5 X1 6 (A45)
X1 2 (-A45)
1 4 (ULT)
1150 1150
BK BK
J318
1150 1150 1150 1150 1150 1150 1150 1150 1150 1150 1150 1150
BK BK BK BK KB6 KA1 BK BK BK BK BK BK BK BK
1150
BK
KA6 KA6 KA6 ATN/ATT X312 5 (-ULT) KB6 KA1/KB6 A95/AN3 UEU/ UEU/ ULT ULT A45
X312 6 (ULT) UFL/UHX/ UFL/UHX/ 1150
1150 UGN+Z75 UGN+Z75 BK
BK
J357 J313
1150 AS8
BK
J353
1150
BK
G311
L
O
C
A9A E1C E63D E1E E55LR
Outside Rearview Mirror Accent Flood S52 Accent Flood E1LR D
- Driver Lamp - E1D Lamp - Outside S13D Lamp - Lamp - Accent E
S
Driver Accent Driver Rearview Door Lock Left Rear Left Rear Lamp - C
Door Lamp - Door Mirror Switch - Door Door Left Rear
E17D Handle Driver Door Handle Switch Driver Handle Pocket Door
Outside Rearview Mirror
Glass - Driver
2 2 2
E4Y E4Y 1150 1150 1150
Turn Turn P34D BK BK BK
Signal Signal Side Object 3 (A45) 4
Repeater Repeater Detection 5 (-A45)
Lamp - Lamp - Indicator - 2 2 2
Left Left Driver 1150 1150 1150
1150 1150 1150 1150 1150
BK BK BK BK BK BK BK BK
J716
Z75 Z75 DL3/DL8/DR4
X4 2 X3 2 X2 1 J516 1150
BK
1150 1150 1150
BK/WH BK/RD VT E8YD X705 5 A24LR
Outside Door
Rearview X88/Z88 Z75 Handle
Mirror A24D Assembly -
Courtesy Door Handle Left Rear
X525 2 5 Lamp - Assembly - Driver Exterior
Driver Exterior
1150 1150
BK/WH BK/WH
E8XA M101L B27LR A23LR
A23D B27D Door Handle Seat Belt Door E8XC Door
DR4 DL3 UKC DL3 M74D Door Door Handle Courtesy S79D Retractor Handle Door Handle Latch S79LR
Window Latch Switch - Lamp - Window Motor Switch - Courtesy Assembly Window
Motor - Assembly Driver Driver Switch - Module - Left Rear Lamp - Left - Left Switch -
Driver - Driver Exterior Exterior Driver Left Exterior Rear Exterior Rear Left Rear
1150
BK/WH
J517
HD7 HD7
1 3 1 1 3 3 5
1150 1150 1150 1150 1150 1150
BK/WH BK BU BK BK BU
X510 5 11
5 X505 23 17 5
1150 1150 1150 1150 1150 1150 1150 1150 1150 1150 1150 1150
BK BK BK BK BK BK BK BK BK BK BK BK
DD8
J515 J715
X500 2 X700 2
AX7
1150 1150
BK BK
G311
L
O
C
E14H E14C E14D K134P
B124RR Seat Seat K53P Seat K55P K29 E1B Seat Bolster S64P D
Folding Seat Heating Heating Seat Blower Heating Seat Blower Seat Accent Memory G31P Seat E
S
Back Position Element - Element - Assembly - Element - Assembly - Heating Lamp - Control Seat Lumbar/ Adjuster C
Switch - 2nd Right Rear Passenger Passenger Passenger Passenger Control Passenger Module - Bolster Pump Switch -
Row Right Cushion Back Back Cushion Cushion Module Seat Passenger - Passenger Passenger
2 2 4 2 4 X1 8 4 2 X1 5 (AG2)
4 (ULT)
1 1250 1250
BK BK
J328
1250 1250 1250 1250 1250 1250
BK BK BK BK BK BK
KA1 KB6 KB6+ULT
1250
BK
2 2 1250 1250
BK BK
AZ3
1250
1250 1250 1250 AZ3 ATN/ATT/KA6 AX7 BK
BK BK BK
J364 J362
-AG2/AX7/Z75
AG2
1250
BK
G312
L
O
C
E1F
A9B E1M E63P Accent E55RR E1RR
Outside Rearview Mirror Accent E1P Flood Lamp - Flood Accent D
- Passenger Lamp - Accent S79P S13P Right Lamp - Lamp - E
Lamp - S
Passenger Lamp - Passenger Window Door Lock Rear Right Right C
Door Passenger Door Switch - Switch - Door Rear Door Rear
E17P Handle Door Handle Passenger Passenger Handle Pocket Door
Outside Rearview Mirror
Glass - Passenger
2 2 2
E4Z E4Z 1250 1250 1250
Turn Turn P34P BK BK BK
Signal Signal Side Object 13 4
Repeater Repeater Detection
Lamp - Lamp - Indicator - 2 2 2
Right Right Passenger 1250 1250 1250
1250 1250 1250 1250 1250 BK BK BK
BK BK BK BK BK
J816
Z75 Z75
X4 2 X3 2 X2 1 1250
J616 BK
E8XB B27RR
B27P Door Handle Door E8XD
DR4 DL3 UKC DL3 M74P A23P Door Handle Courtesy Handle Door Handle A23RR S79RR
Window Door Latch Switch - Lamp - Switch - Courtesy Door Latch Window
Motor - Assembly - Passenger Passenger Right Rear Lamp - Right Assembly - Switch -
Passenger Passenger Exterior Exterior Exterior Rear Exterior Right Rear Right Rear
1250 1250 1250
BK/WH BK/WH BK
J617
HD7 HD7
1 3 X605 17 3 5
1250 1250 1250 1250
BK/WH BK BU BU
X610 5 11
5 5
1250 1250 1250 1250 1250 1250 1250 1250 1250 1250
BK BK BK BK BK BK BK BK BK BK
DD8
J615 J815
1250 1250
BK BK
X600 2 X800 2
1250 1250
BK BK
J363
1250
BK
G312
L
O
K188 C
Human
Machine K74
K73 Interface Human X82 D
E
P17 S140 Telematics Control Machine P22B P22A Audio/ X83 S
Info Media Disc Communication Module Interface A33 Video Video X92 Video Auxiliary B87 C
Display Eject A11 Interface Bypass Control Media Disc Display - Display - USB Input Audio Rearview
Module Switch Radio Control Module Module Module Player 3rd Row 2nd Row Receptacle Adapter Input Camera
6 X3 16 X1 7 X1 5 X1 8 8 (TG5)X2 8 X2 8 (-ULT) X1 4 X1 4 X1 4
A26 A22 A20 7 (U42) X2 19 (ULT) 2550
HVAC Radio Radio/HVAC BK
Controls Controls Controls
W9
Blunt Cut -
Police
Provision IO3-D07 UVH UVC UQA/UQH/UQS
J350
2550 2550
BK BK
5W4/9C1
G325
L
O
C
D
E
S
C
K36
Inflatable
K84 K124 K182 Restraint
Keyless B119 Active Parking Sensing K85
Entry Multi-axis Safety Assist and Passenger
Control Acceleration Control Control Diagnostic Presence
Module Sensor Module Module Module Module
X1 14 6 X1 8 X1 7 X1 19 4
2751
BK
BTM/UGN -BTM/UGN
UD5/UD7
G327
L
E42L O
(T89) (-T89) (T89) (-T89) Tail Lamp C
A90 E5L E5AS E4LR E5AT E5B K174L E5E E5A K174L E5E Assembly -
Logic Stop Stop/Turn Turn Stop/Turn Backup Multifunction Tail Backup Multifunction Tail Left
Lamp - Signal Signal Signal Lamp - LED Control Lamp - Lamp - LED Control Lamp - D
B Right E
Left Lamp - Lamp - Lamp - Module - Left Left Module - Left S
Left Left Rear Left Left Tail Left Tail C
Upper Lower Lamp Lamp
BK BK BK X88 Z88 BK BK BK
J410
1750
BK
X88/Z88 Z75
1750
BK
M95L M95R
Assist Assist
E8ZL Step - E8ZR Step -
Running Left Running Right
X410 6 KR98 Board Step Board Step
Vehicle Courtesy Courtesy
Level K38 Lamp - Lamp -
Control Chassis Left Right
K133 Compressor Control
Trailer Relay Module
G3 K19 Brake X88
Air Suspension Power Trailer 1750 1750
Suspension Control Control Connector BK BK
Compressor Module Module
B 8 8
85 13
J451
-BRS/JL1/Z85/Z95 BRS/JL1/Z85/Z95
J450
1750
BK
G400
L
O
C
B233LR B233RR
K171 Radar Radar D
Hands-Free B218L B218R Sensor Sensor E29RR E29RR E7L E7R S141 E
S
Liftgate Side Object Side Object Module - Module - E29LR E29LR Fog Fog S46B A23C M33 License License M45 Liftgate C
Sensor Sensor Sensor Short Short Fog Lamp Fog Lamp Lamp - Lamp - Liftgate Liftgate Liftgate Plate Plate Rear Window
Control Module - Module - Range Range - Left - Left Right Right Unlatch Latch Window Latch Lamp - Lamp - Wiper Unlatch
Module Left Right Left Rear Right Rear Rear Rear Rear Rear Switch Assembly Assembly Left Right Motor Switch
B 2 2 B 2 2
3 7 7 8 3 4 8 1450 1 2 3 1 1
BK
1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450 1450
TC2 BK BK BK BK BK BK BK BK BK BK BK BK BK BK BK BK
E18
Rear
Defogger
UKC UKC UVZ UVZ UVZ UVZ T79 T79 TB4 TB4 Grid
J499 J904
X2 1
X80RR
Accessory E6
-T79/UKC/UVZ T79/UKC/UVZ Power Center
Receptacle - High K39 1450
Rear E36AH Mounted Liftgate BK
Compartment Dome Stop Control
Lamp Lamp J902
Right Module
K8A
Blower
Motor
Control B B
Module -
X1 5 Auxiliary C X2 6
1450 1450 1450 1450 1450 1450
BK BK BK BK BK BK
X900 11 4 18
X495 8 X486 2 X485 2
TB5/TC2
J402
1450 1450
BK BK
G402
B+ B+ L
O
X51R X51L C
Fuse Block - Fuse Block
F21DR Instrument F7DL - Instrument D
10A Panel Right 10A Panel Left E
S
C
X3 1 X3 12
3140 240
RD/GN RD/YE
X319 1 X316 17
3140 240
RD/GN RD/YE
3
S63
Roof
Beacon
Switch
4 1
5990
WH/BK
C1 C2
KR58
Roof
Beacon
Relay
A2 A1
W11
Blunt Cut -
Roof
Beacon
Provision
1050
BK
G210
B+ L
O
C
X50A
Fuse Block -
F109UA Underhood D
10A E
S
C
X1 G5
K9
Body
Control
Module
X1 15
X272 A
6820 6841
GN BU/GN
X275 36 34
X122 D B C E F A
G102
L
O
C
D
E
W14 S
Blunt Cut - W4 C
Emergency Blunt Cut -
Vehicle Off-Road
Siren Grille Lamp
Provision Provision
6837 6838
BU/GN GY/VT
6836 6835
GN/YE YE/GN
X272 B C D E
6837 6838
BU/GN GY/VT
6836 6835
GN/YE YE/GN
X275 37 38 39 40
6837 6838
BU/GN GY/VT
6836 6835
GN/YE YE/GN
X195 A B C D
6837 6838
BU/GN GY/VT
6836 6835
GN/YE YE/GN
W14 W4
Blunt Cut - Blunt Cut -
Emergency Off-Road
Vehicle Grille Lamp
Siren Provision
Provision
B+ L
O
C
X50A
Fuse Block -
Underhood D
E
KR3 S
C
Horn
Relay
F93UA
15A
X3 L6 X1 J2
28
BN/WH
X273 A
28 29
BN/WH BN/GY
X5 19
K9
Body
Control
Module
X3 18
3287
GN/WH
X1 10
X85 2
Steering Wheel Air P12
Bag Coil Horn
X2 1
3287
BN/WH
1
S33
Horn 1
Switch
2 150
BK
1050
BK
G210 G101
L
O
C
2 2 2 2 2 2 D
P19AG P19J P19AL P19AH P19W P19AM E
S
Speaker - Speaker - Speaker - Speaker - Speaker - Speaker - C
Left Front Left Left Rear Right Front Right Right
Door Instrument Door Door Instrument Rear Door
1 1 Panel 1 1 1 Panel 1
201 118 201 118 199 116 200 117 200 117 46 115
BU BN/BU BU BN/BU GN GN/BK YE YE/BK YE YE/BK WH BU/BK
9 9 9 9 9 9
X225 33 12
201 118 201 118 199 116 200 117 200 117 46 115
BU BN/BU BU BN/BU GN GN/BK YE YE/BK YE YE/BK WH BU/BK
9 9 9 9 9 9
X225 41 20 14 35
X275 41 20 14 35
X271 5 1 7 3 6 2 8 4
X3 1 9 3 11 2 10 4 12
A11
Radio
L
O
C
D
B+ E
S
C
X51L
Fuse Block
- Instrument
F26DL Panel Left
15A
X2 27 14
7X6/7X7 7X7
4640 4140
RD/VT RD/GY
A A
E35L E35R
Exterior Exterior
Spot Spot
Lamp - Lamp -
Left Right
L
O
C
W9 D
E
Blunt Cut - S
Police C
Provision
817
GN/GY
X7 19
X61A
Junction
Block -
Instrument
Panel
X2 47
817
GN/GY
X185 40
817
GN/GY
33
K17
Electronic
Km/h Brake
MPH Control
Module
L
O
C
B+ D
E
S
X51L X50A C
Fuse Block Fuse Block -
- Instrument Underhood
KR73 Panel Left KR73
KR76A Ignition Ignition
Retained Accessory Main Main
Power Relay 1 Relay Relay
F8DL F33DL
10A 15A F78UA F77UA F69UA F70UA
5A 5A 5A 5A
X1 44 30
85 30 85 30 85 30 85 30
KR161A KR161B KR161C KR161D
Configurable Configurable Configurable Configurable
Provision Provision Provision Provision
Relay 1 Relay 2 Relay 3 Relay 4
86 87 86 87 86 87 86 87
43 1939 F63UA F28UA F44UA F47UA
VT/YE VT/VH 30A 30A 30A 30A
X3 M5 M7 F3 X4 G2 L6 K5 L1 K2
X2 50 X1 46 21 16 34 31 30 35 38 48
X61A
Junction
Block -
Instrument
Panel
X3-48 X7 8 11 X5-35 X5 10 X7 20 X5 17 X7 14 X5 11 X7 4 X5 23 X7 1 10 X4 16
(Not Used) (Not Used)
43 1939 961 965 962 966 963 967 964 968 1050 1050
VY/YE VT/WH BU/GN RD/GN BU/GN RD/GN BU/GN RD/GN BU/GN RD/GN BK BK
W9
Blunt Cut -
Police
Provision
G210
B+ L
O
X50A X51L C
Fuse Block - Fuse Block
KR73 Underhood KR76A F34DL - Instrument D
Ignition Retained 15A Panel Left E
Main Accessory Power S
C
Relay Relay 1
KR87
Transmission
F75UA F8DL Park Position
10A 10A Relay
X3 M8 X1 44 34 X2 43
6812
YE
X275 30
B+
6812
X50E YE
Fuse Block X5 23
F1UE F2UE - Battery K9
Auxiliary F19DL Body
100A 50A
P Control
Module
X1 A X2 A X5 12
6311
WH/BU
J358
Trailer
Connector/ Cruise Control
Provision Schematics
Schematics
X1 A
X53A W9
Fuse Blunt Cut -
Block - Police
Rear Provision
Body
W9
Blunt Cut -
Police
Provision
G325
L
O
C
X51L
B+ Fuse Block
KR76A D
- Instrument E
X51R Retained Accessory Power Panel Left S
Fuse Block - Relay 1 C
Instrument
F36DR Panel Right
30A
F8DL
10A
X2 38
X1 44
2340 43
RD/YE VT/YE
X4 31 X2 50
X61A
Junction
Block -
Instrument
Panel
X7 7 8
2340 43
RD YE
1 9
K127
B+ IGN Communication
Interface
Module -
WLAN Router
2
750
BK
G210
L
B+ O
C
X50A
Fuse Block - D
Underhood E
S
KR61 KR53 C
KR63L KR63R
Trailer Stop/Turn Trailer Stop/Turn Signal Trailer Backup Park Lamps
Signal Lamp Relay - Lamp Relay - Right Lamps Relay Relay
Left
X5 K5 X4 L4 L2 X5 K6 N2 M8 J3
J374 J376
W9 W9
Blunt Cut - Blunt Cut -
Police Police
Provision Provision
X5 8 17
K9
Body
Control
Module
22
G D E A F B WH
X88
Trailer
Connector
G400
L
O
C
D
E
B+ S
C
X50A K9
Fuse Block - Body
F36UA Underhood Control
30A X88 Module
Trailer
Connector
X4 H5 C X7 16 X2 20
47
BU
3691 3691
WH/BU WH/BU
-JL1 JL1
242
RD/GN
X185 32
J289
Trailer Brake
Control
Schematics
47 3691 3691
BU WH/BU WH/BU
X2 35 48 44 X1 44 X5 27
X61A
Junction
Block -
Instrument
Panel
X4 16 X6 A C D B
W24
Blunt Cut -
Trailer
Brakes
G210 Provision
A6D Fuel Pump and Level Sensor L96 Under the vehicle, mounted in the rear fuel tank — A6D Fuel Pump and Level Sensor
Assembly - Secondary Assembly - Secondary
A7 Fuel Pump and Level Sensor — Under the vehicle in the fuel tank — A7 Fuel Pump and Level Sensor
Assembly Assembly
A9A Outside Rearview Mirror - Driver — Outside the vehicle, at the front of the driver door —
• Front of Vehicle Components (X88)
• Front of Vehicle Components (Z88)
• Front of Vehicle Components (Z75)
A9B Outside Rearview Mirror - — Outside the vehicle, at the front of the passenger —
Passenger door
• Front of Vehicle Components (Z75)
• Front of Vehicle Components (X88)
• Front of Vehicle Components (Z88)
A10 Inside Rearview Mirror — In the passenger compartment, at the top center Overhead Console Components
of the windshield
• A10 Inside Rearview Mirror X1
• A10 Inside Rearview Mirror X2 (DRZ)
A11 Radio — In the passenger compartment, center of the
instrument panel, behind the HVAC controls
• Back of Instrument Panel • A11 Radio X1
Components (X88/Z88 with D07/DCK)
• A11 Radio X2
• Front of Instrument Panel
Components (X88/Z88 without • A11 Radio X3
D07/DCK)
A14D Seat Lumbar Support Pump - A45, with Y91 or Z75 without In the passenger compartment, part of the driver Driver Seat Back Components A14D Seat Lumbar Support Pump -
Driver ULT seat back Driver
A14P Seat Lumbar Support Pump - Y91 or Z75 without ULT In the passenger compartment, part of the Passenger Seat Components View A14P Seat Lumbar Support Pump -
Passenger passenger seat back Passenger
A16 Transfer Case Motor NP0 or NQH On the underbody, mounted to the bottom rear of Transfer Case Components (NP0 or A16 Transfer Case Motor
the transfer case NQH)
A19D DVD Player - Driver Seat AYE In the passenger compartment, back side of — —
Headrest driver seat head rest
A19P DVD Player - Passenger Seat AYE In the passenger compartment, back side of — —
Headrest passenger seat head rest
A23C Liftgate Latch Assembly — In the passenger compartment, at the bottom Liftgate Components
middle of the liftgate
• A23C Liftgate Latch Assembly
(TB5/TC2)
A23D Door Latch Assembly - Driver — In the passenger compartment, at the middle rear A23D Door Latch Assembly - Driver
of the driver door
• Driver Door Components (X88 or
Z88)
A23P Door Latch Assembly - — In the passenger compartment, at the middle rear A23P Door Latch Assembly -
Passenger of the passenger door
• Passenger Door Components (X88 or Passenger
Z88)
A24D Door Handle Assembly - Driver — Outside the vehicle, at the rear of the driver door —
Exterior
• Driver Door Components (Z75)
• Driver Door Components (X88 or
Z88)
A24LR Door Handle Assembly - Left — Outside the vehicle, at the rear of the left rear
Rear Exterior door
• Left Rear Door Components (Z75) • A24LR Door Handle Assembly - Left
Rear Exterior (X88/Z88)
• Left Rear Door Components (X88 or
Z88) • A24LR Door Handle Assembly - Left
Rear Exterior (Z75)
A24P Door Handle Assembly - — Outside the vehicle, at the rear of the passenger
Passenger Exterior door
• Passenger Door Components (X88 or • A24P Door Handle Assembly -
Z88) Passenger Exterior (ATH+(X88/Z88))
A24RR Door Handle Assembly - Right — Outside the vehicle, at the rear of the right rear
Rear Exterior door
• Right Rear Door Components (X88 or • A24RR Door Handle Assembly -
Z88) Right Rear Exterior (X88/Z88)
A26 HVAC Controls X88 or Z88 In the passenger compartment, at the center of —
the instrument panel, part of the info display
• Front of Instrument Panel
Components (X88/Z88 without
module
D07/DCK)
A34 HVAC Controls - Auxiliary AZ3/D07/DCK In the passenger compartment, forward of center,
between the driver and passenger seat, at the
• Center Console Rear Component • A34 HVAC Controls - Auxiliary (AZ3)
Views (Z75)
back of the floor console • A34 HVAC Controls - Auxiliary
• Center Console Rear Component (X88/Z88+D07)
Views (X88/Z88)
• A34 HVAC Controls - Auxiliary
• Headliner Components (X88/Z88+DCK)
B1 A/C Refrigerant Pressure Sensor — In the front of the engine compartment, on the B1 A/C Refrigerant Pressure Sensor
right side of the A/C compressor
• Right Rear Side of Engine
Components (L83 or L86)
B5LF Wheel Speed Sensor - Left Front — Outside the vehicle, in the left front hub Chassis Components View B5LF Wheel Speed Sensor - Left Front
assembly
B5LR Wheel Speed Sensor - Left Rear — Outside the vehicle, in the left rear, along axle at Chassis Components View B5LR Wheel Speed Sensor - Left Rear
brake rotor
B5RF Wheel Speed Sensor - Right — Outside the vehicle, in the right front hub Chassis Components View B5RF Wheel Speed Sensor - Right
Front assembly Front
B5RR Wheel Speed Sensor - Right — Outside the vehicle, in the right rear, along axle — B5RR Wheel Speed Sensor - Right
Rear at brake rotor Rear
B7C Air Temperature Sensor - Duct — In the passenger compartment, in the floor vent — —
Lower Auxiliary of the rear HVAC
B7D Air Temperature Sensor - Duct — In the passenger compartment, behind the Front of HVAC Assembly Components —
Left Lower instrument panel, on the left side of the HVAC
module
B7E Air Temperature Sensor - Duct — In the passenger compartment, behind the Front of HVAC Assembly Components —
Right Lower instrument panel, on the right side of the HVAC
module
B7G Air Temperature Sensor - Duct SWB In the passenger compartment, in the roof vent of — —
Upper Auxiliary the rear HVAC
B7H Air Temperature Sensor - Duct — In the passenger compartment, behind the Back of HVAC Assembly Components —
Left Upper instrument panel, on the upper left side of the
HVAC module
B7J Air Temperature Sensor - Duct — In the passenger compartment, behind the Back of HVAC Assembly Components —
Right Upper instrument panel, on the upper right side of the
HVAC module
B12A Transmission Fluid Pressure MYC or MYD Under the vehicle, internal to the transmission — —
Switch assembly, part of the control solenoid valve
B13 Transmission Fluid Temperature — Under the vehicle, internal to the transmission Automatic Transmission Valve Body —
Sensor assembly, part of the control solenoid valve Components (M5U)
B14A Transmission Output Shaft — Under the vehicle, internal to the transmission B14A Transmission Output Shaft
Speed Sensor assembly
• Automatic Transmission Internal Speed Sensor
Components (MYC or MYD)
B14C Transmission Input Shaft Speed — Under the vehicle, internal to the transmission Automatic Transmission Case —
Sensor assembly Components (M5U)
B14D Transmission Intermediate Shaft M5U Under the vehicle, internal to the transmission Automatic Transmission Case —
Speed Sensor assembly Components (M5U)
B15 Transmission Internal Mode M5U Under the vehicle, internal to the transmission —
Switch assembly
• Automatic Transmission Case
Components (M5U)
B18 Battery Current Sensor — In the engine compartment, right rear, near the Right Rear of Engine Compartment B18 Battery Current Sensor
battery, on the negative battery cable Components (1 of 2)
B19B Brake Booster Vacuum Sensor — At the rear of the engine compartment, left of the Left Side of Engine Compartment B19B Brake Booster Vacuum Sensor
brake fluid reservoir, on brake booster vacuum Component View
check valve
B20 Brake Fluid Level Switch — At the rear of the engine compartment, on the Left Side of Engine Compartment B20 Brake Fluid Level Switch
brake fluid reservoir Component View
B22 Brake Pedal Position Sensor — In the passenger compartment, behind the brake Behind Left Side of Instrument Panel B22 Brake Pedal Position Sensor
pedal assembly Components (1 of 2)
B23 Camshaft Position Sensor — In the engine compartment, at the front of the Front of Engine Components (L83 or B23 Camshaft Position Sensor
engine, left side of timing chain cover. L86)
B24 Cellular Phone Microphone — In the passenger compartment, at the front Headliner Components B24 Mobile Telephone Microphone
center of the headliner, near the left sunshade
B27D Door Handle Switch - Driver — Outside the vehicle, at the rear of the driver door,
Exterior part of the door handle assembly
• Driver Door Components (Z75) • B27D Door Handle Switch - Driver
Exterior (X88/Z88)
• Driver Door Components (X88 or
Z88) • B27D Door Handle Switch - Driver
Exterior (Z75)
B27LR Door Handle Switch - Left Rear — Outside the vehicle, at the rear of the left rear —
Exterior door, part of the door handle assembly
• Left Rear Door Components (Z75)
• Left Rear Door Components (X88 or
Z88)
B27P Door Handle Switch - Passenger — Outside the vehicle, at the rear of the passenger
Exterior door, part of the door handle assembly
• Passenger Door Components (X88 or • B27P Door Handle Switch -
Z88) Passenger Exterior (X88/Z88)
B27RR Door Handle Switch - Right Rear — Outside the vehicle, at the rear of the right rear —
Exterior door, part of the door handle assembly
• Right Rear Door Components (X88 or
Z88)
B35 Engine Oil Level Switch L83 or L86 In the engine compartment, bottom right side of Right Rear Side of Engine Components B35 Engine Oil Level Switch
engine (L83 or L86)
B37B Engine Oil Pressure Sensor L83 or L86 In the engine compartment, top of the engine,
below throttle body
• Left Side of Engine Components (L83 • B37B Engine Oil Pressure Sensor
or L86) ((L83/L86)+MYC)
B37B Engine Oil Pressure Sensor L96 In the engine compartment, top of the engine,
below throttle body
• Left Side of Engine Components (L83 • B37B Engine Oil Pressure Sensor
or L86) ((L83/L86)+MYC)
B39 A/C Evaporator Temperature — In the passenger compartment, part of HVAC Back of HVAC Assembly Components —
Sensor module, behind the instrument panel
B46B Fuel Level Sensor - Secondary L96 Under the vehicle, at the rear of the vehicle, — —
inside the rear fuel tank, part of A6D fuel pump
and level sensor - Secondary
B47 Fuel Pressure Sensor — On the vehicle underbody, on the fuel line, near — —
the transmission crossmember mount
B52C Heated Oxygen Sensor - Bank 1 — On the vehicle underbody, near the top left side B52C Heated Oxygen Sensor - Bank 1
Sensor 1 of the transmission
• Heated Oxygen Sensors (L83 or L86) Sensor 1
• Heated Oxygen Sensors (L96)
B52D Heated Oxygen Sensor - Bank 1 — On the vehicle underbody, near the left frame rail B52D Heated Oxygen Sensor - Bank 1
Sensor 2 downstream from the catalytic converter
• Heated Oxygen Sensors (L96) Sensor 2
• Heated Oxygen Sensors (L83 or L86)
B52E Heated Oxygen Sensor - Bank 2 — On the vehicle underbody, near the right frame
Sensor 1 rail even with the catalytic converter
• Heated Oxygen Sensors (L83 or L86) • B52E Heated Oxygen Sensor - Bank
2 Sensor 1 ((L83/L86)+MYC)
• Heated Oxygen Sensors (L96)
• B52E Heated Oxygen Sensor - Bank
2 Sensor 1 (L86+M5U)
B52F Heated Oxygen Sensor - Bank 2 — On the vehicle underbody, near the right frame B52F Heated Oxygen Sensor - Bank 2
Sensor 2 rail downstream from the catalytic converter
• Heated Oxygen Sensors (L83 or L86) Sensor 2
• Heated Oxygen Sensors (L96)
B55 Hood Ajar Switch L96 In the front of the engine compartment, part of B55 Engine Hood Switch
the hood latch
• Behind Front Fascia Components
(Z75)
B55 Hood Ajar Switch L83 or L86 In the front of the engine compartment, part of B55 Engine Hood Switch
the hood latch
• Behind Front Fascia Components
(Z75)
B59L Front Impact Sensor - Left — At the front of the vehicle, behind the front B59L Front Impact Sensor - Left
fascia, left of center, behind the bumper beam
• Behind Front Fascia Components
(Z75)
B59R Front Impact Sensor - Right — At the front of the vehicle, behind the front B59R Front Impact Sensor - Right
fascia, right of center, behind the bumper beam
• Behind Front Fascia Components
(X88/Z88)
B61P Seat Belt Tension Sensor - — In the passenger compartment, right side, at the — B61P Seat Belt Tension Sensor -
Passenger base of the B-pillar Passenger
B62D Seat Position Sensor - Driver — In the passenger compartment, right front corner B62D Seat Position Sensor - Driver
of the driver seat track assembly
• Driver Seat Cushion Components
(without ULT)
B63LF Side Impact Sensor - Left Front — In the driver door, behind the trim panel, toward B63LF Side Impact Sensor - Left Front
the rear of the door
• Driver Door Components (X88 or
Z88)
B63RF Side Impact Sensor - Right Front — In the passenger door, behind the trim panel, B63RF Side Impact Sensor - Right
toward the rear of the door
• Passenger Door Components (X88 or Front
Z88)
B67A Ultrasonic Intrusion Sensor 1 UTT In the passenger compartment, at the front of the — —
roof, in the overhead console, part of the Content
Theft Deterrent Sensor Module
B67B Ultrasonic Intrusion Sensor 2 UTT In the passenger compartment, at the front of the — —
roof, in the overhead console, part of the Content
Theft Deterrent Sensor Module
B67C Ultrasonic Intrusion Sensor 3 UTT In the passenger compartment, at the front of the — —
roof, in the overhead console, part of the Content
Theft Deterrent Sensor Module
B68A Knock Sensor 1 — In the engine compartment, on the left side of the Left Side of Engine Components (L83
engine, near the back, below the cylinder head or L86)
• B68A Knock Sensor 1
((L83/L86)+MYC)
B71L Liftgate Object Sensor - Left TB5 or TC2 At the rear of the vehicle, along the left edge of Liftgate Components B71L Liftgate Object Sensor - Left
the liftgate
B71R Liftgate Object Sensor - Right TB5 or TC2 At the rear of the vehicle, along the right edge of Liftgate Components B71R Liftgate Object Sensor - Right
the liftgate
B74 Manifold Absolute Pressure L83 or L86 In the engine compartment, on the top of the
Sensor intake manifold, left of the throttle body
• Left Side of Engine Components (L83 • B74 Manifold Absolute Pressure
or L86) Sensor ((L83/L86)+MYC)
B74 Manifold Absolute Pressure L96 In the engine compartment, on the top of the
Sensor engine, behind the throttle body
• Left Side of Engine Components (L83 • B74 Manifold Absolute Pressure
or L86) Sensor ((L83/L86)+MYC)
B77LF Radio Volume Compensator NKC In the passenger compartment, on the left side of Headliner Components B77LF Radio Volume Compensator
Interior Noise Microphone - Left the headliner, at the over head grab handle Interior Noise Microphone - Left Front
Front
B77R Radio Volume Compensator NKC In the passenger compartment, at the rear of the Headliner Components B77R Radio Volume Compensator
Interior Noise Microphone - Rear headliner Interior Noise Microphone - Rear
B77RF Radio Volume Compensator NKC In the passenger compartment, on the right side B77RF Radio Volume Compensator
Interior Noise Microphone - Right of the headliner, at the over head grab handle
• Headliner Components Interior Noise Microphone - Right Front
Front • Headliner Components
B80 Park Brake Switch without J71 In the passenger compartment, at the left side of Left Front of Passenger Compartment B80 Park Brake Switch
the Driver Footwell, on top of brake pedal Views (Z75)
assembly
B81B Park Position Switch — In the passenger compartment, on the steering Steering Column Components (2 of 2) B81B Park Position Switch
column near the base of the shifter
B87 Rearview Camera — At the rear of the vehicle, on the outside of the
liftgate, in the license plate bezel
• Rear of Vehicle Components (Z75) • B87 Rearview Camera X1 (UVC)
• Rear of Vehicle Components (X88) • B87 Rearview Camera X2 (DRZ)
• Rear of Vehicle Components (Z88)
B88D Seat Belt Switch - Driver — In the passenger compartment, part of the driver B88D Seat Belt Switch - Driver
seat belt buckle
• Driver Seat Cushion Components
(without ULT)
B88P Seat Belt Switch - Passenger — In the passenger compartment, part of the Passenger Seat Cushion Components B88P Seat Belt Switch - Passenger
passenger front seat belt buckle (without ULT)
B99 Steering Wheel Angle Sensor — In the passenger compartment, near the base of Steering Column Components (1 of 2) B99 Steering Wheel Angle Sensor
the steering column, near the floor
B107 Accelerator Pedal Position — In the passenger compartment, on the driver floor Behind Left Side of Instrument Panel B107 Accelerator Pedal Position
Sensor board above the accelerator pedal Components (1 of 2) Sensor
B115 Vehicle Speed Sensor NP0 or NQH Under the vehicle, center, forward of middle, on Transfer Case Components (NP0 or B115 Vehicle Speed Sensor
top of transfer case NQH)
B118B Windshield Washer Fluid Level — In the engine compartment, left front, on the B118B Windshield Washer Fluid Level
Switch bottom of the washer reservoir bottle
• Left Front Corner of Vehicle Switch
Components
B119 Multi-axis Acceleration Sensor UGN In the passenger compartment, under floor Front Center of The Passenger B119 Multi-axis Acceleration Sensor
console, next to the Inflatable Restraint Sensing Compartment Components
and Diagnostic Module
B124LR Folding Seat Back Position ATN or ATT In the passenger compartment, part of the left 2nd Row Left Bucket Seat B124LR Folding Seat Back Position
Switch - 2nd Row Left second row seat, located below the outboard seat Components (ATN) Switch - 2nd Row Left
back hinge
B124RR Folding Seat Back Position ATN or ATT In the passenger compartment, part of the right 2nd Row Right Bucket Seat B124RR Folding Seat Back Position
Switch - 2nd Row Right second row seat, located below the outboard seat Components (ATN) Switch - 2nd Row Right
back hinge
B150 Fuel Tank Pressure Sensor — Under the vehicle, at the rear, mounted to the Chassis Components View B150 Fuel Tank Pressure Sensor
EVAP cannister
B152LF Suspension Position Sensor - Z95 Outside the vehicle, at the left front corner, rear — B152LF Suspension Position Sensor -
Left Front side of the strut tower Left Front
B152LR Suspension Position Sensor - Z95 Outside the vehicle, at the left rear corner, above Chassis Components View B152LR Suspension Position Sensor -
Left Rear the upper control arm mount to the frame rail Left Rear
B152RF Suspension Position Sensor - Z95 Outside the vehicle, at the right front corner, rear — B152RF Suspension Position Sensor -
Right Front side of the strut tower Right Front
B152RR Suspension Position Sensor - Z95 Outside the vehicle, at the right rear corner, B152RR Suspension Position Sensor -
Right Rear above the upper control arm mount to the frame
• Chassis Components View Right Rear
rail • Chassis Components View
B159L Glass Breakage Sensor - Left UTT In the rear compartment, left side, underneath Left Rear Cargo Area Components
rear quarter glass window
• B159L Glass Breakage Sensor - Left
(UTV+SWB)
B159R Glass Breakage Sensor - Right UTT In the rear compartment, right side, underneath Right Rear Cargo Area Components
rear quarter glass window
• B159R Glass Breakage Sensor -
Right (UTT/UTV+SWB)
B165 Content Theft Deterrent Sensor UTT In the passenger compartment, at the front of the — B165 Content Theft Deterrent Sensor
Module roof, in the overhead console Module
B174G Frontview Camera - Grille UVH At the front of the vehicle, center, in the upper — —
grille
B174W Frontview Camera - Windshield UFL, UHX, or UGN In the passenger compartment, at the top middle Overhead Console Components B174W Frontview Camera - Windshield
of the windshield
B196 Air Suspension Pressure Sensor Z85 or Z95 under the vehicle, at the left rear, part of the level — —
ride compressor
B198 Fuel Composition Sensor FHS Under the vehicle, between the fuel tank and the — B198 Fuel Composition Sensor
electronic brake control module, on the main fuel
line
B200 Rain Sensor Module — In the passenger compartment, at the top middle — —
of the windshield
B218L Side Object Sensor Module - Left UKC At the left rear corner of the vehicle, mounted to Behind Rear Fascia Components B218L Side Object Sensor Module -
the inside of the rear fascia Left
B218R Side Object Sensor Module - UKC At the right rear corner of the vehicle, mounted to Behind Rear Fascia Components B218R Side Object Sensor Module -
Right the inside of the rear fascia Right
B225L Sideview Camera - Left UVH Outside the vehicle, in the left outside rearview — —
mirror
B225R Sideview Camera - Right UVH Outside the vehicle, in the right outside rearview — —
mirror
B227 Gear Position Sensor NP0 or NQH Under the vehicle, on the top rear of the transfer Transfer Case Components (NP0 or B227 Gear Position Sensor
case NQH)
B233LF Radar Sensor Module - Short UVZ At the front of the vehicle, mounted to the inside — B233LF Radar Sensor Module - Short
Range Left Front left of the front fascia Range Left Front
B233LR Radar Sensor Module - Short UVZ At the rear of the vehicle, mounted to the inside Behind Rear Fascia Components B233LR Radar Sensor Module - Short
Range Left Rear of the rear fascia left of center Range Left Rear
B233RF Radar Sensor Module - Short UVZ At the front of the vehicle, mounted to the inside — B233RF Radar Sensor Module - Short
Range Right Front right of the front fascia Range Right Front
B233RR Radar Sensor Module - Short UVZ At the rear of the vehicle, mounted to the inside Behind Rear Fascia Components B233RR Radar Sensor Module - Short
Range Right Rear of the rear fascia right of center Range Right Rear
B275A Hands-Free Liftgate Sensor - TC2 At the rear of the vehicle, center, mounted to the — —
Upper underside of the rear bumper, above trailer hitch
B275B Hands-Free Liftgate Sensor - TC2 At the rear of the vehicle, center, mounted to the — —
Lower underside of the rear bumpe, below trailer hitch
B306A Parking Assist Sensor - Front UD5 At the front of the vehicle, mounted in the front B306A Parking Assist Sensor - Front
Left Outer bumper
• Front of Vehicle Components (Z75) Left Outer
• Front of Vehicle Components (X88)
• Front of Vehicle Components (Z88)
B306B Parking Assist Sensor - Front UD5 At the front of the vehicle, mounted in the front B306B Parking Assist Sensor - Front
Left Middle bumper
• Front of Vehicle Components (Z75) Left Middle
• Front of Vehicle Components (X88)
• Front of Vehicle Components (Z88)
B306C Parking Assist Sensor - Front UD5 At the front of the vehicle, mounted in the front B306C Parking Assist Sensor - Front
Right Middle bumper
• Front of Vehicle Components (Z75) Right Middle
• Front of Vehicle Components (X88)
• Front of Vehicle Components (Z88)
B306D Parking Assist Sensor - Front UD5 At the front of the vehicle, mounted in the front B306D Parking Assist Sensor - Front
Right Outer bumper
• Front of Vehicle Components (X88) Right Outer
• Front of Vehicle Components (Z88)
• Front of Vehicle Components (Z75)
B306E Parking Assist Sensor - Rear UD5 or UD7 At the rear of the vehicle, mounted in the rear B306E Parking Assist Sensor - Rear
Left Outer bumper
• Rear of Vehicle Components (X88) Left Outer
• Rear of Vehicle Components (Z88)
• Rear of Vehicle Components (Z75)
B306F Parking Assist Sensor - Rear UD5 or UD7 At the rear of the vehicle, mounted in the rear B306F Parking Assist Sensor - Rear
Left Middle bumper
• Rear of Vehicle Components (Z88) Left Middle
• Rear of Vehicle Components (Z75)
• Rear of Vehicle Components (X88)
B306G Parking Assist Sensor - Rear UD5 or UD7 At the rear of the vehicle, mounted in the rear B306G Parking Assist Sensor - Rear
Right Middle bumper
• Rear of Vehicle Components (X88) Right Middle
• Rear of Vehicle Components (Z75)
• Rear of Vehicle Components (Z88)
B306L Parking Assist Sensor - Side UKG At the front of the vehicle, mounted in the front Front of Vehicle Components (Z75) B306L Parking Assist Sensor - Side
Right Front bumper Right Front (UKG)
B306M Parking Assist Sensor - Side Left UKG At the rear of the vehicle, mounted in the rear Rear of Vehicle Components (Z75) B306M Parking Assist Sensor - Side
Rear bumper Left Rear
B306N Parking Assist Sensor - Side UKG At the rear of the vehicle, mounted in the rear Rear of Vehicle Components (Z75) B306N Parking Assist Sensor - Side
Right Rear bumper Right Rear
B310 Fuel Pressure/Temperature L86 or L83 In the engine compartment, mounted to the left Top of Engine Components (L83 or —
Sensor rear of engine fuel injector rail L86)
C1B Battery - Auxiliary 5W4 or 9C1 In the engine compartment, on the left side, Left Side of Engine Compartment —
forward of the underhood fuse block Component View
C1 Battery — In the engine compartment, on the left side, near Right Rear of Engine Compartment —
the underhood fuse block Components (1 of 2)
E1A Accent Lamp - Driver Seat AN3 or A95 In the passenger compartment, under the driver E1A Accent Lamp - Driver Seat
seat
• Driver Seat Cushion Components
(ULT)
E1AA Floor Accent Lamp - Left Front — In the passenger compartment, under the left E1AA Floor Accent Lamp - Left Front
side of the instrument panel
• Back of Instrument Panel
Components (Z75)
E1AB Floor Accent Lamp - Right Front — In the passenger compartment, under the right E1AB Floor Accent Lamp - Right Front
side of the instrument panel
• Back of Instrument Panel
Components (X88/Z88 without
D07/DCK)
E1B Accent Lamp - Passenger Seat AN3 or A95 In the passenger compartment, under the E1B Accent Lamp - Passenger Seat
passenger seat
• Passenger Seat Cushion
Components (without ULT)
E1C Accent Lamp - Driver Door — In the passenger compartment, forward of center, E1C Accent Lamp - Driver Door Handle
Handle left side, on the driver door, near the door handle
• Driver Door Components (Z75)
• Driver Door Components (X88 or
Z88)
E1D Accent Lamp - Driver Door Z75 In the passenger compartment, forward of center, Driver Door Components (Z75) E1D Accent Lamp - Driver Door (Z75)
left side, on the driver door, in the arm rest
E1LR Accent Lamp - Left Rear Door Z75 In the passenger compartment, rearward of Left Rear Door Components (Z75) E1LR Accent Lamp - Left Rear Door
center, left side, on the left rear door, above the
door handle
E1M Accent Lamp - Passenger Door — In the passenger compartment, forward of center, E1M Accent Lamp - Passenger Door
Handle right side, on the passenger door, near the door
• Passenger Door Components (X88 or Handle
Z88)
handle
• Passenger Door Components (Z75)
E1P Accent Lamp - Passenger Door Z75 In the passenger compartment, forward of center, Passenger Door Components (Z75) E1P Accent Lamp - Passenger Door
right side, on the passenger door, in the arm rest (Z75)
E1RR Accent Lamp - Right Rear Door Z75 In the passenger compartment, rearward of Right Rear Door Components (Z75) E1RR Accent Lamp - Right Rear Door
center, right side, on the right rear door, above
the door handle
E2LF Side Marker Lamp - Left Front — At the left front corner of the vehicle, inside the —
headlamp assembly, part of the headlamp
• Headlamp Components (X88)
assembly • Headlamp Components (Z75)
• Headlamp Components (Z88)
• Headlamp Components (Z88)
E2RF Side Marker Lamp - Right Front — At the right front corner of the vehicle, inside the —
headlamp assembly, part of the headlamp
• Headlamp Components (X88)
assembly • Headlamp Components (Z75)
E4A Cornering Lamp - Left Z75 At the front left corner of the vehicle, in the front — —
fascia, in the multifunction lamp assembly
E4AC Park/Daytime Running Lamp - X88 or Z88 At the left front corner of the vehicle, inside the —
Left headlamp assembly, part of the headlamp
• Headlamp Components (X88)
assembly • Headlamp Components (Z88)
E4AD Park/Daytime Running Lamp - X88 or Z88 At the right front corner of the vehicle, inside the —
Right headlamp assembly, part of the headlamp
• Headlamp Components (X88)
assembly • Headlamp Components (Z88)
E4AL Park/Daytime Running Lamp - Z75 At the front left corner of the vehicle, in the front Front of Vehicle Components (Z75) —
Left Lower fascia, in the multifunction lamp assembly
E4AM Park/Daytime Running Lamp - Z75 At the front right corner of the vehicle, in the front Front of Vehicle Components (Z75) —
Right Lower fascia, in the multifunction lamp assembly
E4B Cornering Lamp - Right Z75 At the front right corner of the vehicle, in the front — —
fascia, in the multifunction lamp assembly
E4C Daytime Running Lamp - Left Z75 At the left front corner of the vehicle, inside the Headlamp Components (Z75) —
headlamp assembly, part of the headlamp
assembly
E4E Headlamp - Left High Beam X88 or Z88 At the left front corner of the vehicle, inside the —
headlamp assembly, part of the headlamp
• Headlamp Components (Z88)
assembly • Headlamp Components (Z75)
• Headlamp Components (X88)
E4E Headlamp - Left High Beam Z75 At the left front corner of the vehicle, inside the —
headlamp assembly, part of the headlamp
• Headlamp Components (Z88)
assembly • Headlamp Components (Z75)
• Headlamp Components (X88)
E4F Headlamp - Right High Beam X88 or Z88 At the right front corner of the vehicle, inside the —
headlamp assembly, part of the headlamp
• Headlamp Components (Z75)
assembly • Headlamp Components (X88)
• Headlamp Components (Z88)
E4F Headlamp - Right High Beam Z75 At the right front corner of the vehicle, inside the —
headlamp assembly, part of the headlamp
• Headlamp Components (Z75)
assembly • Headlamp Components (X88)
• Headlamp Components (Z88)
E4G Headlamp - Left Low Beam X88 or Z88 At the right front corner of the vehicle, inside the —
headlamp assembly, part of the headlamp
• Headlamp Components (X88)
assembly • Headlamp Components (Z88)
• Headlamp Components (Z75)
E4G Headlamp - Left Low Beam Z75 At the left front corner of the vehicle, inside the —
headlamp assembly, part of the headlamp
• Headlamp Components (X88)
assembly • Headlamp Components (Z88)
• Headlamp Components (Z75)
E4H Headlamp - Right Low Beam X88 or Z88 At the right front corner of the vehicle, inside the —
headlamp assembly, part of the headlamp
• Headlamp Components (X88)
assembly • Headlamp Components (Z75)
• Headlamp Components (Z88)
E4H Headlamp - Right Low Beam Z75 At the right front corner of the vehicle, inside the —
headlamp assembly, part of the headlamp
• Headlamp Components (X88)
assembly • Headlamp Components (Z75)
• Headlamp Components (Z88)
E4J Park Lamp - Left Front X88 without Y91 At the left front corner of the vehicle, inside the Headlamp Components (X88) —
headlamp assembly
E4K Park Lamp - Right Front X88 without Y91 At the right front corner of the vehicle, inside the Headlamp Components (X88) —
headlamp assembly
E4LF Turn Signal Lamp - Left Front X88 or Z88 At the left front corner of the vehicle, inside the —
headlamp assembly
• Headlamp Components (X88)
• Front of Vehicle Components (Z75)
E4LF Turn Signal Lamp - Left Front Z75 At the front left corner of the vehicle, in the front —
fascia, in the multifunction lamp assembly
• Headlamp Components (X88)
• Front of Vehicle Components (Z75)
E4Y Turn Signal Repeater Lamp - Left DR4 At the front of the Left front door, part of the Door Mirror Components —
Outside Rearview Mirror
E4Z Turn Signal Repeater Lamp - DL3 At the front of the Right front door, part of the Door Mirror Components —
Right Outside Rearview Mirror, part of the mirror glass
E4Z Turn Signal Repeater Lamp - DR4 At the front of the Right front door, part of the Door Mirror Components —
Right Outside Rearview Mirror
E5A Backup Lamp - Left X88 or Z88 At the left rear corner of the vehicle, inside the —
tail lamp assembly
• Tail Lamp Components (X88)
• Tail Lamp Components (Z75)
• Tail Lamp Components (Z88)
E5A Backup Lamp - Left Z75 At the left rear corner of the vehicle, inside the —
tail lamp assembly, part of the tail lamp
• Tail Lamp Components (X88)
assembly • Tail Lamp Components (Z75)
• Tail Lamp Components (Z88)
E5AS Stop/Turn Signal Lamp - Left X88 without T89 At the left rear corner of the vehicle, inside the Tail Lamp Components (X88) —
Upper tail lamp assembly
E5AT Stop/Turn Signal Lamp - Left X88 without T89 At the left rear corner of the vehicle, inside the Tail Lamp Components (X88) —
Lower tail lamp assembly
E5AU Stop/Turn Signal Lamp - Right X88 without T89 At the right rear corner of the vehicle, inside the Tail Lamp Components (X88) —
Upper tail lamp assembly
E5AV Stop/Turn Signal Lamp - Right X88 without T89 At the right rear corner of the vehicle, inside the Tail Lamp Components (X88) —
Lower tail lamp assembly
E5B Backup Lamp - Right X88 or Z88 At the right rear corner of the vehicle, inside the —
tail lamp assembly
• Tail Lamp Components (Z88)
• Tail Lamp Components (Z75)
• Tail Lamp Components (X88)
E8B Door Sill Plate Lamp - Passenger Z75 In the passenger compartment, forward of center, — E8B Door Sill Plate Lamp - Passenger
right, at the bottom of the passenger door
opening on the sill
E8Q Door Sill Plate Lamp - Left Rear Z75 In the passenger compartment, forward of center, Left Rear of Passenger Compartment E8Q Door Sill Plate Lamp - Left Rear
left, at the bottom of the left rear door opening on Views (Z75)
the sill
E8R Door Sill Plate Lamp - Right Rear Z75 In the passenger compartment, forward of center, — E8R Door Sill Plate Lamp - Right Rear
right, at the bottom of the right rear door opening
on the sill
E8XA Door Handle Courtesy Lamp - HD7 On the outside of the vehicle, left side, rear of — —
Driver Exterior driver door, part of the door handle assembly
E8XC Door Handle Courtesy Lamp - HD7 On the outside of the vehicle, left side, rear of — —
Left Rear Exterior left rear door, part of the door handle assembly
E8XD Door Handle Courtesy Lamp - HD7 On the outside of the vehicle, right side, rear of — —
Right Rear Exterior right rear door, part of the door handle assembly
E8YD Outside Rearview Mirror DL3 At the front of the Left front door, bottom of the —
Courtesy Lamp - Driver Outside Rearview Mirror
• Door Mirror Components
• Front of Vehicle Components (Z75)
E8YP Outside Rearview Mirror DL3 At the front of the Right front door, bottom of the —
Courtesy Lamp - Passenger Outside Rearview Mirror
• Front of Vehicle Components (Z75)
• Door Mirror Components
E8ZL Running Board Step Courtesy BRS Outside of vehicle, left side, under the rocker, — —
Lamp - Left mounted in the running board
E8ZR Running Board Step Courtesy BRS Outside of vehicle, right side, under the rocker, — —
Lamp - Right mounted in the running board
E13LA Headlamp Assembly - Left — At the left front corner of the vehicle —
• Front of Vehicle Components (X88)
• Front of Vehicle Components (Z88)
• Front of Vehicle Components (Z75)
E13RA Headlamp Assembly - Right — At the right front corner of the vehicle —
• Front of Vehicle Components (X88)
• Front of Vehicle Components (Z88)
• Front of Vehicle Components (Z75)
E14A Seat Heating Element - Driver KA1 or KB6 In the passenger compartment, in the driver seat Driver Seat Back Components
Back back
• E14A Seat Heating Element - Driver
Back (X88/Z88+KQV)
E14B Seat Heating Element - Driver KA1 or KB6 In the passenger compartment, part of the driver
Cushion seat cushion
• Driver Seat Cushion Components • E14B Seat Heating Element - Driver
(without ULT) Cushion (X88/Z88+KQV)
E14C Seat Heating Element - KA1 or KB6 In the passenger compartment, in the passenger Passenger Seat Components View
Passenger Back seat back
• E14C Seat Heating Element -
Passenger Back (X88/Z88+KQV)
E14D Seat Heating Element - KA1 or KB6 In the passenger compartment, part of the Passenger Seat Cushion Components
Passenger Cushion passenger seat cushion (without ULT)
• E14D Seat Heating Element -
Passenger Cushion (KB6+Z75+ULT)
• 2nd Row Left Bucket Seat • E14F Seat Heating Element - Left
Components (ATN) Rear Cushion (Z75+KA6)
E14H Seat Heating Element - Right KA6 In the passenger compartment, in the 2nd row
Rear Cushion seat, right cushion
• 2nd Row Seat Cushions Components • E14H Seat Heating Element - Right
(ATT) Rear Cushion (X88/Z88+KA6)
• 2nd Row Right Bucket Seat • E14H Seat Heating Element - Right
Components (ATN) Rear Cushion (Z75+KA6)
E15 Steering Wheel Heater UVD In the passenger compartment, in the steering — —
wheel.
E17D Outside Rearview Mirror Glass - — Outside of the vehicle, left side, forward on the — —
Driver driver door, inside the outside rear view mirror
E17P Outside Rearview Mirror Glass - — Outside of the vehicle, right side, forward on the — —
Passenger passenger door, inside the outside rear view
mirror
E18 Rear Defogger Grid — In the passenger compartment, on the inside of Rear of Vehicle Components (Z75)
the liftgate window
• E18 Rear Defogger Grid X1
• E18 Rear Defogger Grid X2
E28 Center Console Compartment D07 without DCK In the passenger compartment, inside the center E28 Center Console Compartment
Lamp console compartment
• Center Console Internal Component Lamp
Views (X88/Z88)
E29LF Fog Lamp - Left Front T3U At the left front corner of the vehicle, in the front E29LF Fog Lamp - Left Front (X88)
bumper
• Front of Vehicle Components (X88)
• Front of Vehicle Components (Z88)
E29LR Fog Lamp - Left Rear T79 At the left rear corner of the vehicle, in the rear —
fascia
• E29LR Fog Lamp - Left Rear (X88)
• E29LR Fog Lamp - Left Rear (Z75)
E29RF Fog Lamp - Right Front T3U At the right front corner of the vehicle, in the front E29RF Fog Lamp - Right Front (X88)
bumper
• Front of Vehicle Components (X88)
• Front of Vehicle Components (Z88)
E29RR Fog Lamp - Right Rear T79 At the right rear corner of the vehicle, in the rear —
fascia
• E29RR Fog Lamp - Right Rear (X88)
• E29RR Fog Lamp - Right Rear (Z75)
E31L Sunshade Mirror Lamp - Left — In the passenger compartment, on the left Overhead Console Components E31L Sunshade Mirror Lamp - Left
sunshade
E31R Sunshade Mirror Lamp - Right — In the passenger compartment, on the right Overhead Console Components E31R Sunshade Mirror Lamp - Right
sunshade
E32 Cigarette Lighter Receptacle DT4 with AZ3 In the passenger compartment, center of — —
instrument panel, below P17 Info Display
E32 Cigarette Lighter Receptacle DT4 with D07 or DCK In the passenger compartment, on top of the floor — —
console, below P17 Info Display
E35R Exterior Spot Lamp - Right 7X7 In the passenger compartment, forward, top right E35R Exterior Spot Lamp - Right
corner of the instrument panel near the A-Pillar
• Back of Instrument Panel
Components (X88/Z88 with D07/DCK)
E36AH Dome Lamp without SWB In the rear compartment, near center, overhead, — E36AH Dome Lamp
in the headliner
E37B Dome/Reading Lamps - 2nd Row without U42 In the passenger compartment, overhead, in the Headliner Components E37B Dome/Reading Lamps - 2nd Row
headliner between the front and second row
seating
E37B Dome/Reading Lamps - 2nd Row U42 In the passenger compartment, overhead, in the Headliner Components E37B Dome/Reading Lamps - 2nd Row
headliner between the front and second row
seating, part of the second row video display
E37C Dome/Reading Lamps - 3rd Row without DNU In the passenger compartment, overhead, in the Headliner Components E37C Dome/Reading Lamps - 3rd Row
headliner behind the second row seating
E37C Dome/Reading Lamps - 3rd Row DNU In the passenger compartment, overhead, in the Headliner Components E37C Dome/Reading Lamps - 3rd Row
headliner behind the second row seating, part of
the third row video display
E37EL Dome/Reading Lamps - Front — In the passenger compartment, at the left front of Overhead Console Components E37EL Dome/Reading Lamps - Front
Overhead Console Left the headliner, in the overhead console Overhead Console Left
E37ER Dome/Reading Lamps - Front — In the passenger compartment, at the right front Overhead Console Components E37ER Dome/Reading Lamps - Front
Overhead Console Right of the headliner, in the overhead console Overhead Console Right
E37H Dome/Reading Lamps - Left Roof U42 In the passenger compartment, overhead, in the Headliner Components E37H Dome/Reading Lamps - Left
Rail video display between the front and second row Roof Rail
seating
E37J Dome/Reading Lamps - Right U42 In the passenger compartment, overhead, in the Headliner Components E37J Dome/Reading Lamps - Right
Roof Rail video display between the front and second row Roof Rail
seating
E38 Flood Lamp - Center Console — In the passenger compartment, overhead, Overhead Console Components E38 Flood Lamp - Center Console
forward of center, on the overhead console
E42L Tail Lamp Assembly - Left — Outside of the vehicle, at the left rear corner of —
the vehicle
• Rear of Vehicle Components (Z75)
• Rear of Vehicle Components (Z88)
• Rear of Vehicle Components (X88)
E42R Tail Lamp Assembly - Right — Outside of the vehicle, at the right rear corner of —
the vehicle
• Rear of Vehicle Components (Z75)
• Rear of Vehicle Components (X88)
• Rear of Vehicle Components (Z88)
E55LR Flood Lamp - Left Rear Door Z75 In the passenger compartment, rear of center, Left Rear Door Components (Z75) E55LR Flood Lamp - Left Rear Door
Pocket left side, in the left rear door trim, inside the arm Pocket
rest
E63D Flood Lamp - Driver Door Handle Z75 In the passenger compartment, forward of center, Driver Door Components (Z75) E63D Flood Lamp - Driver Door Handle
left side, in the driver door trim, inside the door (Z75)
handle pocket
E63P Flood Lamp - Passenger Door Z75 In the passenger compartment, forward of center, Passenger Door Components (Z75) E63P Flood Lamp - Passenger Door
Handle right side, in the passenger door trim, inside the Handle (Z75)
door handle pocket
E69L Multifunction Lamp Assembly - Z75 Outside of the vehicle, front left corner, mounted — —
Front Fascia Left in the front fascia
E69R Multifunction Lamp Assembly - Z75 Outside of the vehicle, front right corner, — —
Front Fascia Right mounted in the front fascia
F101 Passenger Instrument Panel Air — In the passenger compartment, at the top of the
Bag passenger side of the instrument panel
• Front of Instrument Panel • F101 Passenger Instrument Panel
Components (X88/Z88 with D07/DCK) Air Bag X1
F105L Roof Rail Air Bag - Left — In the passenger compartment, left side, — —
overhead, along the left roof rail
F105R Roof Rail Air Bag - Right — In the passenger compartment, right side, — —
overhead, along the right roof rail
F106D Seat Side Air Bag - Driver — In the passenger compartment, on the left side of Driver Seat Back Components
the left front seat back
• F106D Seat Side Air Bag - Driver
(KB6)
F106DA Seat Side Air Bag - Driver AYQ In the passenger compartment, on the right side Driver Seat Back Components
Inboard of the left front seat back
• F106DA Seat Side Air Bag - Driver
Inboard (KB6)
F106P Seat Side Air Bag - Passenger — In the passenger compartment, on the right side Passenger Seat Components View
of the right front seat back
• F106P Seat Side Air Bag -
Passenger (KB6)
F107 Steering Wheel Air Bag — In the passenger compartment, in the center of — —
the steering wheel
F112D Seat Belt Retractor Pretensioner — In the passenger compartment, left side, at the Left Front of Passenger Compartment
- Driver base of the B-pillar Views (Z75)
• F112D Seat Belt Retractor
Pretensioner - Driver (AX7)
F112P Seat Belt Retractor Pretensioner — In the passenger compartment, right side, at the —
- Passenger base of the B-pillar
• F112P Seat Belt Retractor
Pretensioner - Passenger (AX7)
F113P Seat Belt Anchor Pretensioner - — In the passenger compartment, on the lower Passenger Seat Cushion Components F113P Seat Belt Anchor Pretensioner -
Passenger outside of the passenger seat, mounted to the (without ULT) Passenger
seat track
G1 A/C Compressor — In the engine compartment, right side, mounted Left Side of Engine Components (L83 —
on the lower front of the engine or L86)
G3 Air Suspension Compressor Z85 or Z95 under the vehicle, at the left rear, behind left rear — G3 Air Suspension Compressor
tire
G10L Cooling Fan Motor - Left — At the front of the engine compartment, in the Cooling Fans G10L Cooling Fan Motor - Left
center of the left fan assembly
G10R Cooling Fan Motor - Right — At the front of the engine compartment, in the Cooling Fans G10R Cooling Fan Motor - Right
center of the right fan assembly
G12B Fuel Pump - Secondary L96 Under the vehicle, in the secondary fuel tank, — —
part of the fuel pump and level sensor assembly
G12 Fuel Pump — Under the vehicle, in the fuel tank, part of the fuel — —
pump and level sensor assembly
G13 Generator L83 or L86 In the engine compartment, right of center, at the G13 Generator
top right front of the engine
• Left Side of Engine Components (L83
or L86)
G13 Generator L96 In the engine compartment, left of center, at the G13 Generator
top left front of the engine
• Left Side of Engine Components (L83
or L86)
G18 High Pressure Fuel Pump L83 or L86 In the engine compartment, rearward of center, at Top of Engine Components (L83 or G18 High Pressure Fuel Pump
the top back center of the engine, underneath the L86) (L83/L86)
intake manifold
G19 Rear Window Washer Pump — In the engine compartment, left side, forward of Left Front Corner of Vehicle G19 Rear Window Washer Pump
the wheel well, behind the driver side head lamp Components
assembly
G24 Windshield Washer Pump — In the engine compartment, left side, forward of G24 Windshield Washer Pump
the wheel well, attached to the washer fluid
• Left Front Corner of Vehicle
Components
reservoir, below the left headlamp assembly
• Left Side of Engine Compartment
Component View
G31D Seat Lumbar/Bolster Pump - ULT In the passenger compartment, inside driver seat Driver Seat Cushion Components G31D Seat Lumbar/Bolster Pump -
Driver cushion (ULT) Driver
G31P Seat Lumbar/Bolster Pump - ULT In the passenger compartment, inside passenger Passenger Seat Cushion Components G31P Seat Lumbar/Bolster Pump -
Passenger seat cushion (ULT) Passenger
K4 Assist Step Control Module BRS Underneath the vehicle, along the outside of the Chassis Components View
left frame rail, near the the driver door
• K4 Assist Step Control Module X1
• K4 Assist Step Control Module X2
K14 Distance Sensing Cruise Control K59 Front of vehicle, left side bottom, behind the front Behind Front Fascia Components K14 Distance Sensing Cruise Control
Module fascia, on the frame rail, near ground G101 (X88/Z88) Module
K17 Electronic Brake Control Module — Underneath the vehicle, left side, along the inside Chassis Components View
of the frame rail, near the left side of the
• K17 Electronic Brake Control Module
(L96)
transmission
• K17 Electronic Brake Control Module
(-L96)
K19 Suspension Control Module Z95 Underneath the vehicle, at the back, left of Chassis Components View K19 Suspension Control Module
center, top side of the rear most chassis cross
member, above spare tire
K20 Engine Control Module — In the engine compartment, to the left of the Left Side of Engine Compartment
engine Component View
• K20 Engine Control Module X1
((L83/L86)+MYC)
• 2nd Row Left Bucket Seat • K29R Seat Heating Control Module -
Components (ATN) Rear X1 (Z75+KB6)
K32 Steering Wheel Heating Control UVD In the passenger compartment, on lower center — —
Module of the steering wheel assembly behind the
steering wheel air bag
K33 HVAC Control Module — In the passenger compartment, in the passenger Front of HVAC Assembly Components
side of the Instrument Panel, behind the glove
• K33 HVAC Control Module X1
box, mounted to the top of the HVAC assembly • K33 HVAC Control Module X2
• K33 HVAC Control Module X3
• K33 HVAC Control Module X4
K36 Inflatable Restraint Sensing and — In the passenger compartment, under the center Left Front of Passenger Compartment
Diagnostic Module console, on the floor Views (Z75)
• K36 Inflatable Restraint Sensing and
Diagnostic Module X1
K38 Chassis Control Module JL1 or Z85 Under the vehicle, at the rear, right side, mounted Chassis Components View K38 Chassis Control Module
to the bracket above the spare tire
K39 Liftgate Control Module TB5 or TC2 In the rear compartment, left side of the tailgate, Liftgate Components
behind the trim.
• K39 Liftgate Control Module X1
• K39 Liftgate Control Module X2
• K39 Liftgate Control Module X3
K40D Seat Memory Control Module - A45 or ULT In the passenger compartment, left side, under
Driver the driver seat cushion
• Driver Seat Cushion Components • K40D Seat Memory Control Module -
(without ULT) Driver X1
K40P Seat Memory Control Module - AG2 or ULT In the passenger compartment, right side, under Passenger Seat Cushion Components
Passenger the passenger seat cushion (ULT)
• K40P Seat Memory Control Module -
Passenger X1
K43 Power Steering Control Module — Underneath the vehicle, towards the front, on the — —
power steering rack assembly
K53D Seat Blower Assembly - Driver Z75 In the passenger compartment, forward of center, Driver Seat Back Components
Back left side, inside the driver seat back
• K53D Seat Blower Assembly - Driver
Back (X88/Z88)
K53P Seat Blower Assembly - X88/Z88 In the passenger compartment, forward of center, Passenger Seat Components View
Passenger Back right side, inside the passenger seat back
• K53P Seat Blower Assembly -
Passenger Back (X88/Z88)
K53P Seat Blower Assembly - Z75 In the passenger compartment, forward of center, Passenger Seat Components View
Passenger Back right side, inside the passenger seat back
• K53P Seat Blower Assembly -
Passenger Back (X88/Z88)
K55D Seat Blower Assembly - Driver X88/Z88 In the passenger compartment, forward of center,
Cushion left side, inside the driver seat cushion
• Driver Seat Cushion Components • K55D Seat Blower Assembly - Driver
(without ULT) Cushion (Z75)
K55D Seat Blower Assembly - Driver Z75 In the passenger compartment, forward of center,
Cushion left side, inside the driver seat cushion
• Driver Seat Cushion Components • K55D Seat Blower Assembly - Driver
(without ULT) Cushion (Z75)
K55P Seat Blower Assembly - X88/Z88 In the passenger compartment, forward of center,
Passenger Cushion right side, inside the passenger seat cushion
• Passenger Seat Cushion • K55P Seat Blower Assembly -
Components (without ULT) Passenger Cushion (Z75)
K55P Seat Blower Assembly - Z75 In the passenger compartment, forward of center,
Passenger Cushion right side, inside the passenger seat cushion
• Passenger Seat Cushion • K55P Seat Blower Assembly -
Components (without ULT) Passenger Cushion (Z75)
K56 Serial Data Gateway Module — In the passenger compartment, under the —
instrument panel, left of the steering column
• K56 Serial Data Gateway Module X1
• K56 Serial Data Gateway Module X2
K60 Steering Column Lock Module BTM In the passenger compartment, on steering Steering Column Components (2 of 2) K60 Steering Column Lock Module
column, at shift lever
K69 Transfer Case Control Module NP0 or NQH In the passenger compartment, under the Behind Left Side of Instrument Panel
instrument panel, right of the accelerator pedal Components (1 of 2)
• K69 Transfer Case Control Module
X1
K71 Transmission Control Module M5U In the engine compartment, left side of bulkhead, Left Side of Engine Compartment K71 Transmission Control Module
near the brake master cylinder Component View
K73 Telematics Communication UE1 In the passenger compartment, inside instrument Back of Instrument Panel Components
Interface Control Module panel, right side, above glove box (Z75)
• K73 Telematics Communication
Interface Control Module X1
K74 Human Machine Interface Control IO5 or IO6 In the passenger compartment, right side of the
Module instrument panel, below the passenger air bag
• Back of Instrument Panel • K74 Human Machine Interface
Components (Z75) Control Module X1
K77 Remote Control Door Lock — In the passenger compartment, right rear, on C- — K77 Remote Control Door Lock
Receiver pillar Receiver
K83 Park Brake Control Module J71 Underneath the vehicle, at the rear, near center Chassis Components View K83 Park Brake Control Module
of the rear bumper bar
K84 Keyless Entry Control Module ATH or BTM In the rear compartment, left side, underneath
rear quarter window behind trim
• Right Rear Cargo Area Components • K84 Keyless Entry Control Module
X1
• Left Rear Cargo Area Components
• K84 Keyless Entry Control Module
X2
K85 Passenger Presence Module — In the passenger compartment, under the front of K85 Passenger Presence Module
the front passenger seat cushion
• Passenger Seat Cushion
Components (ULT)
K89 Immobilizer Control Module without BTM In the passenger compartment, on the driver Center Console Bottom Component K89 Immobilizer Control Module
side, near the ignition cylinder Views
K89 Immobilizer Control Module BTM In the passenger compartment, near center, Center Console Bottom Component K89 Immobilizer Control Module
between the driver and passenger seat, inside Views
floor console
K99 Steering Column Position Control N38 In the passenger compartment, forward, left side, Steering Column Components (1 of 2)
Module mounted to the bottom of the steering column
• K99 Steering Column Position
Control Module X1
K111 Fuel Pump Driver Control Module — Underneath the vehicle, rear, mounted to the Chassis Components View K111 Fuel Pump Driver Control Module
bracket above the spare tire
K127 Communication Interface Module Accessory Router Inside the vehicle, under the instrument panel, — —
- WLAN Router near the driver side hush panel
K133 Trailer Brake Power Control JL1 Under the vehicle, mounted to the bracket above Chassis Components View K133 Trailer Brake Power Control
Module the spare tire, next to K111 Module
K134D Seat Bolster Memory Control ULT In the passenger compartment, inside driver seat Driver Seat Cushion Components K134D Seat Bolster Memory Control
Module - Driver cushion (ULT) Module - Driver
K134P Seat Bolster Memory Control ULT In the passenger compartment, inside passenger Passenger Seat Cushion Components K134P Seat Bolster Memory Control
Module - Passenger seat cushion (ULT) Module - Passenger
K157 Video Processing Control Module UVH In the passenger compartment, front, left side, Left Front of Passenger Compartment
left of steering column, behind instrument panel, Views (Z75)
• K157 Video Processing Control
Module X1
near the BCM
• K157 Video Processing Control
Module X2
K166L Multifunction LED Control Module — Outside the vehicle, left front corner, attached to Headlamp Components (Z75) —
- Left Headlamp the headlamp assembly
K166R Multifunction LED Control Module — Outside the vehicle, right front corner, attached Headlamp Components (Z75) —
- Right Headlamp to the headlamp assembly
K167L Multifunction LED Control Module Z75 Outside the vehicle, left front corner, inside front — —
- Front Fascia Left fascia, attached to the Multifunction Lamp
Assembly
K167R Multifunction LED Control Module Z75 Outside the vehicle, right front corner, inside front — —
- Front Fascia Right fascia, attached to the Multifunction Lamp
Assembly
K169 Folding Seat Control Module - 3rd AS8 In the passenger compartment, in the 3rd row 3rd Row Seat Back Components (AS8)
Row seat, left side, inside seat back in the lower left
• K169 Folding Seat Control Module -
3rd Row X1 (AS8)
corner
• K169 Folding Seat Control Module -
3rd Row X2 (AS8)
K171 Hands-Free Liftgate Sensor TC2 At the rear of the vehicle, center, mounted to the Behind Rear Fascia Components K171 Hands - Free Liftgate Sensor
Control Module underside of the rear bumper Control Module X1 (TC2)
K174L Multifunction LED Control Module Z75 or Z88 At the left rear corner of the vehicle, internal to —
- Left Tail Lamp the left tail lamp assembly, attached the tail lamp
• Tail Lamp Components (Z75)
assembly • Tail Lamp Components (Z75)
K174R Multifunction LED Control Module Z75 or Z88 At the left rear corner of the vehicle, internal to — —
- Right Tail Lamp the right tail lamp assembly, attached the tail
lamp assembly
K175 Center Console Compartment DCK In the passenger compartment, center, inside — K175 Center Console Compartment
Cooler Control Module center console at the floor Cooler Control Module
K188 Human Machine Interface Control IO5 or IO6 In the passenger compartment, in the instrument — K188 Human Interface Control Module
Module Bypass Module panel Bypass Module X1
KR4B Outside Rearview Mirror Heater DL3 or DR4 In the rear body fuse block — —
Relay
KR5 Rear Defogger Relay C49 In the rear body fuse block — —
KR23B Fuel Pump Relay - Secondary L96 In the underhood fuse block — —
KR57 Rear Fog Lamp Relay T79 In the rear body fuse block — —
KR58 Roof Beacon Relay TRW In the passenger compartment, overhead, in the — —
overhead console
KR79 Auxiliary Battery Relay 2 5W4 or 9C1 In the engine compartment, left side, near C1B — —
Auxiliary Battery
KR81 Auxiliary Battery Relay 1 5W4 or 9C1 In the engine compartment, left side, near C1B — —
Auxiliary Battery
KR95A Liftgate Unlatch Relay TB4 In the rear body fuse block — —
KR98 Vehicle Level Control Z85 or Z95 In the engine compartment, left side, under brake — KR98 Vehicle Level Control
Compressor Relay master cylinder Compressor Relay
KR161A Configurable Provision Relay 1 5W4 or 9C1 In the underhood fuse block — —
KR161B Configurable Provision Relay 2 5W4 or 9C2 In the underhood fuse block — —
KR161C Configurable Provision Relay 3 5W4 or 9C3 In the underhood fuse block — —
KR161D Configurable Provision Relay 4 5W4 or 9C4 In the underhood fuse block — —
KR162 Liftgate Window Unlatch Relay — In the rear body fuse block — —
M4 Air Inlet Door Actuator — In the passenger compartment, behind the Front of HVAC Assembly Components M4 Air Inlet Door Actuator
instrument panel glove box
M5 Adjustable Pedal Motor JF4 In the passenger compartment, left side, in the Behind Left Side of Instrument Panel M5 Adjustable Pedal Motor
driver footwell, attached to the accelerator pedal Components (1 of 2)
assembly
M6L Air Temperature Door Actuator - — In the passenger compartment, behind the Front of HVAC Assembly Components M6L Air Temperature Door Actuator -
Left instrument panel, on the HVAC case center Left
M6R Air Temperature Door Actuator - — In the passenger compartment, behind the Back of HVAC Assembly Components M6R Air Temperature Door Actuator -
Right instrument panel, on the HVAC case Right
M7 Transmission Shift Lock Control — In the passenger compartment, right side of the Steering Column Components (2 of 2) M7 Transmission Shift Lock Control
Solenoid Actuator steering wheel, attached to transmission shift Solenoid Actuator
lever
M8B Blower Motor - Auxiliary — In the rear compartment, right side, behind the — —
interior rear quarter trim
M8 Blower Motor — In the passenger compartment, behind the Back of HVAC Assembly Components M8 Blower Motor
passenger side of the instrument panel
M26 Front Axle Engagement Actuator NP0 or NQH Underside of the vehicle, at the front, center, on Front Axle Components M26 Front Axle Engagement Actuator
front axle
M27 Fuel Fill Door Unlatch Actuator N08 Underside of the vehicle, near the back, left side, — M27 Fuel Fill Door Unlatch Actuator
under rear quarter glass window, in rear quarter
panel
M31 Liftgate Motor TB5 or TC2 In the rear compartment, left side of liftgate, on Liftgate Components M31 Liftgate Motor
liftgate strut
M33 Liftgate Window Latch Assembly — In the rear compartment, inside the tailgate, at Liftgate Components M33 Liftgate Window Latch Assembly
center
M37B Mode Door Actuator - Auxiliary — In the passenger compartment, forward, internal — —
to the instrument panel
M37L Mode Door Actuator - Left — In the passenger compartment, behind the left Front of HVAC Assembly Components M37L Mode Door Actuator - Left
side of the instrument panel, on the upper left
side of the HVAC module
M38 Power Steering Motor — Under the vehicle, part of the steering gear — —
assembly
M45 Rear Wiper Motor — At rear of vehicle, in the liftgate Liftgate Components M45 Rear Wiper Motor
M50D Seat Front Vertical Motor - Driver — In the passenger compartment, under the front of Driver Seat Cushion Components M50D Seat Front Vertical Motor -
the driver seat, next to the right seat track (without ULT) Driver
M50P Seat Front Vertical Motor - — In the passenger compartment, under the front of Passenger Seat Cushion Components M50P Seat Front Vertical Motor -
Passenger the passenger seat, next to the right seat track (without ULT) Passenger
M51D Seat Horizontal Motor - Driver — In the passenger compartment, under the center M51D Seat Horizontal Motor - Driver
of the driver seat, between the seat tracks
• Driver Seat Cushion Components
(without ULT)
M51P Seat Horizontal Motor - — In the passenger compartment, under the center M51P Seat Horizontal Motor -
Passenger of the passenger seat, between the seat tracks
• Passenger Seat Cushion Passenger
Components (ULT)
M52D Seat Lumbar Support Horizontal without Y91 or Z75 In the passenger compartment, part of the driver Driver Seat Back Components M52D Seat Lumbar Support Horizontal
Motor - Driver seat back Motor - Driver
M55D Seat Rear Vertical Motor - Driver — In the passenger compartment, under the front of M55D Seat Rear Vertical Motor - Driver
the driver seat, next to the left seat track
• Driver Seat Cushion Components
(without ULT)
M55P Seat Rear Vertical Motor - — In the passenger compartment, under the front of M55P Seat Rear Vertical Motor -
Passenger the passenger seat, next to the left seat track
• Passenger Seat Cushion Passenger
Components (without ULT)
M56D Seat Recline Motor - Driver — In the passenger compartment, part of the driver Driver Seat Back Components M56D Seat Recline Motor - Driver
seat back
M56P Seat Recline Motor - Passenger — In the passenger compartment, part of the Passenger Seat Components View M56P Seat Recline Motor - Passenger
passenger seat back
M60A Active Grille Air Shutter 1 Motor — On the front of the vehicle behind the grille in the — M60A Active Grille Air Shutter 1 Motor
Module center of the air shutter assembly Module
M64 Starter Motor — In the engine compartment, lower right rear of the
engine
• Right Rear Side of Engine • M64 Starter Motor ((L83/L86)+MYC)
Components (L96)
• M64 Starter Motor (L86+M5U)
• Right Rear Side of Engine
Components (L83 or L86) • M64 Starter Motor (L96)
M65 Steering Column Telescope N38 In the passenger compartment, forward, left of — —
Motor center, on the steering column
M68 Steering Column Tilt Motor N38 In the passenger compartment, forward, left of — —
center, on the steering column
M74D Window Motor - Driver — In the passenger compartment, behind the driver M74D Window Motor - Driver
door trim panel, at the center of the door
• Driver Door Components (Z75)
• Driver Door Components (X88 or
Z88)
M74LR Window Motor - Left Rear — In the passenger compartment, center of the left M74LR Window Motor - Left Rear
rear door, behind the door trim panel
• Left Rear Door Components (X88 or
Z88)
M77P Outside Rearview Mirror Motor - — Outside of the vehicle, right side, forward on the — —
Passenger passenger door, inside the outside rear view
mirror
M78D Outside Rearview Mirror Folding DL3 or DR4 Outside of the vehicle, left side, forward on the — —
Motor - Driver driver door, inside the outside rear view mirror
M78P Outside Rearview Mirror Folding DL3 or DR4 Outside of the vehicle, right side, forward on the — —
Motor - Passenger passenger door, inside the outside rear view
mirror
M91 Instrument Panel Compartment Z75 In the passenger compartment, forward, right — M91 Instrument Panel Compartment
Door Unlatch Actuator side, inside the instrument panel on the glove Door Unlatch Actuator
box
M95L Assist Step - Left BRS Under the vehicle, along the left frame rail, under Chassis Components View M95L Assist Step - Left
the driver door
M95R Assist Step - Right BRS Under the vehicle, along the right frame rail, Chassis Components View M95R Assist Step - Right
under the passenger door
M101L Seat Belt Retractor Motor Module AX7 In the passenger compartment, left side, at the Left Front of Passenger Compartment M101L Seat Belt Retractor Motor
- Left base of the B-Pillar, part of the seat belt retractor Views (Z75) Module - Left
M101R Seat Belt Retractor Motor Module AX7 In the passenger compartment, right side, at the — M101R Seat Belt Retractor Motor
- Right base of the B-Pillar, part of the seat belt retractor Module - Right
M107LR Folding Seat Motor - 2nd Row ATN or ATT In the passenger compartment, left side, under M107LR Folding Seat Motor - 2nd Row
Left 2nd row seat cushion
• 2nd Row Left Bucket Seat Left
Components (ATN)
M107RR Folding Seat Motor - 2nd Row ATN or ATT In the passenger compartment, right side, under M107RR Folding Seat Motor - 2nd Row
Right 2nd row seat cushion
• 2nd Row Right Bucket Seat Right
Components (ATN)
M108LR Folding Seat Motor - 3rd Row AS8 In the passenger compartment, left side, at the 3rd Row Seat Back Components (AS8) —
Left bottom of the 3rd row seat back
M108RR Folding Seat Motor - 3rd Row AS8 In the passenger compartment, right side, at the 3rd Row Seat Back Components (AS8) —
Right bottom of the 3rd row seat back
M109LR Folding Seat Back Unlatch Motor AS8 In the passenger compartment, left side, at the 3rd Row Seat Back Components (AS8) —
- 3rd Row Left middle of the 3rd row seat back
M109RR Folding Seat Back Unlatch Motor AS8 In the passenger compartment, right side, at the 3rd Row Seat Back Components (AS8) —
- 3rd Row Right middle of the 3rd row seat back
P12 Horn — In the engine compartment, lower left corner of P12 Horn
the radiator support
• Cooling Fans
• Left Side of Engine Compartment
Component View
P16 Instrument Cluster — In the passenger compartment, at the top of the P16 Instrument Cluster
driver side of the instrument panel, above the
• Front of Instrument Panel
Components (X88/Z88 with D07/DCK)
steering column
• Front of Instrument Panel
Components (Z75)
P17 Info Display Module — In the passenger compartment, at the top center
of the instrument panel, above the radio controls
• Front of Instrument Panel • P17 Info Display Module X1
Components (X88/Z88 with D07/DCK) (X88/Z88)
P19AC Speaker - Subwoofer UQA, UQH or UQS In the passenger compartment, forward of center, Front Center of The Passenger P19AC Speaker - Subwoofer
under the floor console, near the instrument panel Compartment Components
P19AG Speaker - Left Front Door — In the passenger compartment, at the front of the P19AG Speaker - Left Front Door
left front door, behind the door trim panel
• Driver Door Components (Z75)
• Driver Door Components (X88 or
Z88)
P19AH Speaker - Right Front Door — In the passenger compartment, at the front of the P19AH Speaker - Right Front Door
right front door, behind the door trim panel
• Passenger Door Components (Z75)
• Passenger Door Components (X88 or
Z88)
P19AL Speaker - Left Rear Door — In the passenger compartment, in the lower left P19AL Speaker - Left Rear Door
rear door, behind the door panel
• Left Rear Door Components (X88 or
Z88)
P19AP Speaker - Right Rear Trim Panel UQA, UQH or UQS In the rear compartment, at the back, right side Right Rear Cargo Area Components P19AP Speaker - Right Rear Trim
at the top of the D-Pillar Panel
P19B Speaker - Center Instrument UQH or UQS In the passenger compartment, center of the P19B Speaker - Center Instrument
Panel instrument panel
• Back of Instrument Panel Panel
Components (Z75)
P19DD Speaker - Left Front Door Woofer UQH In the passenger compartment, at the front of the Driver Door Components (Z75) P19DD Speaker - Left Front Door
left front door, behind the door trim panel Woofer (UQH)
P19J Speaker - Left Instrument Panel — In the passenger compartment, in the upper left
of the instrument panel
• Front of Instrument Panel • P19J Speaker - Left Instrument
Components (X88/Z88 without Panel (UQ3)
D07/DCK)
• P19J Speaker - Left Instrument
• Back of Instrument Panel Panel (UQA/UQH/UQS)
Components (Z75)
P19M Speaker - Left Rear Tweeter UQH In the passenger compartment, in the upper left Left Rear Door Components (Z75) P19M Speaker - Left Rear Tweeter
rear door, behind the door panel, near door handle
P19PD Speaker - Right Front Door UQH In the passenger compartment, at the front of the Passenger Door Components (Z75) P19PD Speaker - Right Front Door
Woofer right front door, behind the door trim panel Woofer
P19VD Speaker - Right Front Door UQH In the passenger compartment, at the front of the Passenger Door Components (Z75) P19VD Speaker - Right Front Door
Tweeter right front door, behind the door trim panel, at the Tweeter (UQH)
door mirror
P19W Speaker - Right Instrument Panel — In the passenger compartment, in the upper right
of the instrument panel
• Back of Instrument Panel • P19W Speaker - Right Instrument
Components (Z75) Panel (UQ3)
P19Z Speaker - Right Rear Tweeter UQH In the passenger compartment, in the upper right Right Rear Door Components (Z75) P19Z Speaker - Right Rear Tweeter
rear door, behind the door panel, near door handle
P22A Video Display - 2nd Row U42 In the passenger compartment, in the headliner Headliner Components
between the front and second row seating
• P22A Video Display - 2nd Row X2
(ULT)
P22B Video Display - 3rd Row DNU In the passenger compartment, in the headliner Headliner Components P22B Video Display - 3rd Row
between the second and third row seating
P25 Power Sounder Content Theft UTT In the engine compartment, rear, under the air — P25 Power Sounder Content Theft
Deterrent Alarm Module inlet grille, near center Deterrent Alarm Module
P29 Head-Up Display UV6 In the passenger compartment, forward left, in P29 Heads - Up Display X1
the instrument panel on the top, forward of the
• Front of Instrument Panel
Components (X88/Z88 with D07/DCK)
gauge cluster
• Front of Instrument Panel
Components (X88/Z88 without
D07/DCK)
P34D Side Object Detection Indicator - UKC At the front of the Left front door, part of the — —
Driver Outside Rearview Mirror, part of the mirror glass
P34P Side Object Detection Indicator - UKC At the front of the Right front door, part of the — —
Passenger Outside Rearview Mirror, part of the mirror glass
P43 Collision Alert Indicators UEU, UFL or UHX without In the passenger compartment, behind the upper P43 Collision Alert Indicators
UV6 left of the instrument panel, above the instrument
• Back of Instrument Panel
Components (X88/Z88 without
cluster
D07/DCK)
P45RR Seat Haptic Movement Motor - UEU, UFL UHX, or UGN In the passenger compartment, part of the driver P45RR Seat Haptic Movement Motor -
Driver Right Rear seat cushion
• Driver Seat Cushion Components Driver Right Rear
(without ULT)
P50 Emergency Call Backup Speaker UI3 In the engine compartment, in the Instrument — P27 Mobile Telephone Speaker
Panel, near center
Q2 A/C Compressor Clutch — In the engine compartment, right of center, on the Q2 A/C Compressor Clutch
right front of the engine, at the bottom.
• Right Rear Side of Engine
Components (L96)
Q4 Vehicle Level Control Solenoid Z85 or Z95 Underside of vehicle, at the rear, part of the air — —
Valve suspension compressor
Q5 Brake Pressure Modulator — In the engine compartment, left rear, part of the — —
Brake Control Module
Q6 Camshaft Position Actuator — In the engine compartment, at the front right side Front of Engine Components (L83 or Q6 Camshaft Position Actuator
Solenoid Valve of the engine L86) Solenoid Valve
Q8 Control Solenoid Valve Assembly MYC or MYD Underside of the vehicle, forward of middle, Automatic Transmission Internal Q8 Control Solenoid Valve Assembly
internal to the transmission Components (MYC or MYD)
Q12 Evaporative Emission Purge L83 or L86 In the engine compartment, forward of center, top
Solenoid Valve and front of the engine just left of the throttle
• Left Rear Side of Engine • Q12 Evaporative Emission Purge
Components (L96) Solenoid Valve ((L83/L86)+MYC)
body
• Left Side of Engine Components (L83 • Q12 Evaporative Emission Purge
or L86) Solenoid Valve (L86+M5U)
Q12 Evaporative Emission Purge L96 In the engine compartment, forward of center, top
Solenoid Valve of the engine, on the left, just behind the
• Left Rear Side of Engine • Q12 Evaporative Emission Purge
Components (L96) Solenoid Valve ((L83/L86)+MYC)
generator
• Left Side of Engine Components (L83 • Q12 Evaporative Emission Purge
or L86) Solenoid Valve (L86+M5U)
Q13 Evaporative Emission Vent — Underneath the vehicle, just left of center, at the Chassis Components View Q13 Evaporative Emission Vent
Solenoid Valve rear of the vehicle, attached to the front facing Solenoid Valve
side of the rear most chassis cross member,
above the spare tire
Q17A Fuel Injector 1 — In the engine compartment, top of the engine, Q17A Fuel Injector 1
attached to the fuel rail, above cylinder 1
• Top of Engine Components (L83 or
L86)
Q17C Fuel Injector 3 — In the engine compartment, top of the engine, Q17C Fuel Injector 3
attached to the fuel rail, above cylinder 3
• Top of Engine Components (L83 or
L86)
Q17D Fuel Injector 4 — In the engine compartment, top of the engine, Q17D Fuel Injector 4
attached to the fuel rail, above cylinder 4
• Right Rear Side of Engine
Components (L96)
Q17E Fuel Injector 5 — In the engine compartment, top of the engine, Q17E Fuel Injector 5
attached to the fuel rail, above cylinder 5
• Top of Engine Components (L83 or
L86)
Q17F Fuel Injector 6 — In the engine compartment, top of the engine, Q17F Fuel Injector 6
attached to the fuel rail, above cylinder 6
• Right Rear Side of Engine
Components (L96)
Q17G Fuel Injector 7 — In the engine compartment, top of the engine, Q17G Fuel Injector 7
attached to the fuel rail, above cylinder 7
• Top of Engine Components (L83 or
L86)
Q17H Fuel Injector 8 — In the engine compartment, top of the engine, Q17H Fuel Injector 8
attached to the fuel rail, above cylinder 8
• Right Rear Side of Engine
Components (L96)
Q27A Pressure Control Solenoid Valve MYC or MYD Underside of the vehicle, forward of middle, — —
1 internal to the transmission, part of the control
solenoid
Q27B Pressure Control Solenoid Valve MYC or MYD Underside of the vehicle, forward of middle, — —
2 internal to the transmission, part of the control
solenoid
Q27C Pressure Control Solenoid Valve MYC or MYD Underside of the vehicle, forward of middle, — —
3 internal to the transmission, part of the control
solenoid
Q27D Pressure Control Solenoid Valve MYC or MYD Underside of the vehicle, forward of middle, — —
4 internal to the transmission, part of the control
solenoid
Q27E Pressure Control Solenoid Valve MYC or MYD Underside of the vehicle, forward of middle, — —
5 internal to the transmission, part of the control
solenoid
Q32A Shift Solenoid Valve 1 MYC or MYD Underside of the vehicle, forward of middle, — —
internal to the transmission, part of the control
solenoid
Q37LF Shock Absorber Actuator - Left Z95 Outside the vehicle, at the left front corner, near — Q37LF Shock Absorber Actuator - Left
Front the top of the strut Front
Q37LR Shock Absorber Actuator - Left Z95 Outside the vehicle, at the left front corner, near Chassis Components View Q37LR Shock Absorber Actuator - Left
Rear the top of the shock Rear
Q37RF Shock Absorber Actuator - Right Z95 Outside the vehicle, at the left front corner, near — Q37RF Shock Absorber Actuator -
Front the top of the strut Right Front
Q37RR Shock Absorber Actuator - Right Z95 Outside the vehicle, at the left front corner, near Chassis Components View Q37RR Shock Absorber Actuator -
Rear the top of the shock Right Rear
Q39A Torque Converter Clutch MYC or MYD Underside of the vehicle, forward of middle, — —
Pressure Control Solenoid Valve internal to the transmission, part of the control
solenoid
Q43 Valve Lifter Oil Manifold L83 or L86 In the engine compartment, mounted in the valve Left Side of Engine Components (L83 Q43 Valve Lifter Oil Manifold
Assembly lifter valley below the intake manifold or L86) Assembly
Q44 Engine Oil Pressure Control L83 or L86 In the engine compartment, at the front of the Front of Engine Components (L83 or Q44 Engine Oil Pressure Control
Solenoid Valve engine, right of the cam actuator L86) Solenoid Valve
Q46 A/C Compressor Solenoid Valve — In the front of the engine compartment, part of Q46 A/C Compressor Solenoid Valve
the compressor assembly
• Right Rear Side of Engine
Components (L96)
Q77A Transmission Control Solenoid M5U Underside of the vehicle, forward of middle, Automatic Transmission Valve Body —
Valve 1 internal to the transmission Components (M5U)
Q77B Transmission Control Solenoid M5U Underside of the vehicle, forward of middle, Automatic Transmission Valve Body —
Valve 2 internal to the transmission Components (M5U)
Q77C Transmission Control Solenoid M5U Underside of the vehicle, forward of middle, Automatic Transmission Valve Body —
Valve 3 internal to the transmission Components (M5U)
Q77D Transmission Control Solenoid M5U Underside of the vehicle, forward of middle, Automatic Transmission Valve Body —
Valve 4 internal to the transmission Components (M5U)
Q77E Transmission Control Solenoid M5U Underside of the vehicle, forward of middle, Automatic Transmission Valve Body —
Valve 5 internal to the transmission Components (M5U)
Q77F Transmission Control Solenoid M5U Underside of the vehicle, forward of middle, Automatic Transmission Valve Body —
Valve 6 internal to the transmission Components (M5U)
Q77G Transmission Control Solenoid M5U Underside of the vehicle, forward of middle, Automatic Transmission Valve Body —
Valve 7 internal to the transmission Components (M5U)
Q77H Transmission Control Solenoid M5U Underside of the vehicle, forward of middle, Automatic Transmission Valve Body —
Valve 8 internal to the transmission Components (M5U)
Q77J Transmission Control Solenoid M5U Underside of the vehicle, forward of middle, Automatic Transmission Valve Body —
Valve 9 internal to the transmission Components (M5U)
R6E Terminating Resistor - High UGN In the rear compartment, at the back, about —
Speed Extension Bus 1 21CM from the Breakout to the Left Glass
• R6E Terminating Resistor - High
Speed Extension Bus 1 (UHX/UDV)
Breakage Sensor
• R6E Terminating Resistor - High
Speed Extension Bus 1 (Z75+UGN)
R6E Terminating Resistor - High UHX In the passenger compartment, In the Instrument —
Speed Extension Bus 1 Panel, Taped to the breakout to the X305
• R6E Terminating Resistor - High
Speed Extension Bus 1 (UHX/UDV)
connector
• R6E Terminating Resistor - High
Speed Extension Bus 1 (Z75+UGN)
R6F Terminating Resistor - High — In the passenger compartment, In the Instrument — R6F Terminating Resistor - High Speed
Speed Extension Bus 2 Panel, Taped near the breakout to the Right front Extension Bus 2
floor accent lamp
S2A Transmission Manual Shift KB7 In the passenger compartment, part of the Steering Column Components (1 of 2) —
Switch - Up/Down transmission shift lever
S3 Transmission Shift Lever — In the passenger compartment, forward, left of Steering Column Components (1 of 2) S3 Transmission Shift Lever
center, on the right side of the steering column
S5 Center Console Compartment D07 In the passenger compartment, under the center S5 Center Console Compartment Lamp
Lamp Switch console compartment lid
• Center Console Rear Component Switch
Views (X88/Z88)
S12 Dome Lamp Switch — In the passenger compartment, overhead, Overhead Console Components S12 Dome Lamp Switch
forward of center, in the overhead console
S13D Door Lock Switch - Driver — In the passenger compartment, in the driver door S13D Door Lock Switch - Driver
handle trim panel
• Driver Door Components (X88 or
Z88)
S25 Garage Door Opener UG1 In the passenger compartment, overhead, Overhead Console Components S25 Garage Door Opener
forward of center, in the overhead console
S27 Head-Up Display Switch UV6 In the passenger compartment, left side, on the S27 Head-Up Display Switch
instrument panel, left of the instrument cluster
• Front of Instrument Panel
Components (Z75)
S31D Seat Heating and Cooling Switch KA1 or KB6, without Z75 In the passenger compartment, forward, on the Center Console Top Component Views S31D Seat Heating and Cooling Switch
- Driver instrument panel, on driver side of the HVAC (X88/Z88) - Driver
controls, in floor console bezel
S31P Seat Heating and Cooling Switch KA1 or KB6, without Z75 In the passenger compartment, forward, on the Center Console Top Component Views S31P Seat Heating and Cooling Switch
- Passenger instrument panel, on passenger side of the HVAC (X88/Z88) - Passenger
controls, in floor console bezel
S38 Ignition Mode Switch BTM In the passenger compartment, forward, left of S38 Ignition Mode Switch
center, in the instrument panel, right of steering
• Front of Instrument Panel
Components (Z75)
column
• Front of Instrument Panel
Components (X88/Z88 with D07/DCK)
S39 Ignition Switch without BTM In the passenger compartment, forward, behind — —
the steering wheel, on the right side of the
steering column
S43 Content Theft Deterrent Sensor UTT In the passenger compartment, overhead, in the Overhead Console Components S43 Content Theft Deterrent Sensor
Disable Switch overhead console Disable Switch
S45B Liftgate Control Switch - Interior TB5 or TC2 In the passenger compartment, overhead, in the Overhead Console Components S45B Liftgate Control Switch - Interior
overhead console
S46B Liftgate Unlatch Switch TB4 At the rear of the vehicle, in the liftgate S46B Liftgate Unlatch Switch
• Rear of Vehicle Components (X88)
• Rear of Vehicle Components (Z88)
S46 Liftgate Handle Switch TB5 In the rear compartment, rear, right of center, in Liftgate Components S46 Liftgate Handle Switch
the liftgate, at the bottom
S47D Seat Memory Switch - Driver A45 In the passenger compartment, on the driver door S47D Seat Memory Switch - Driver
panel below the driver door arm rest
• Driver Door Components (Z75)
• Driver Door Components (X88 or
Z88)
S48A Multifunction Switch - Instrument X88 or Z88 In the passenger compartment, left side of the S48A Multifunction Switch - Instrument
Panel instrument panel, left of steering column
• Front of Instrument Panel Panel
Components (X88/Z88 with D07/DCK)
S48C Multifunction Switch 1 - Z75 In the passenger compartment, near the center of Front of Instrument Panel Components S48C Multifunction Switch 1 -
Instrument Panel the instrument panel, left of P17 (Z75) Instrument Panel
S48D Multifunction Switch 2 - Z75 In the passenger compartment, near the center of Front of Instrument Panel Components S48D Multifunction Switch 2 -
Instrument Panel the instrument panel, right of P17 (Z75) Instrument Panel
S51 Telematics Button Assembly UE1 In the passenger compartment, forward, Overhead Console Components S51 Telematics Button Assembly
overhead, part of the rearview mirror at the (DRZ)
bottom
S63 Roof Beacon Switch TRW In the passenger compartment, behind the — —
overhead console
S64D Seat Adjuster Switch - Driver — In the passenger compartment, mounted to the
outboard side of the driver seat cushion
• Driver Seat Cushion Components • S64D Seat Adjuster Switch - Driver
(without ULT) X1 (A45)
S64P Seat Adjuster Switch - — In the passenger compartment, mounted to the Passenger Seat Cushion Components
Passenger outboard side of the passenger seat cushion (without ULT)
• S64P Seat Adjuster Switch -
Passenger X1 ((AG2+AG6)-ULT)
S70E Steering Wheel Controls Switch - X88 or Z88 with UK3 In the passenger compartment, on the left rear Steering Wheel Components (X88 or S70E Steering Wheel Controls Switch -
Radio Presets side of the steering wheel Z88) Radio Presets
S70F Steering Wheel Controls Switch - X88 or Z88 with UK3 In the passenger compartment, on the right rear Steering Wheel Components (X88 or S70F Steering Wheel Controls Switch -
Radio Volume side of the steering wheel Z88) Radio Volume
S70L Steering Wheel Controls Switch - — In the passenger compartment, on the left side of
Left the steering wheel
• Steering Wheel Components (Z75) • S70L Steering Wheel Controls
Switch - Left (X88)
• Steering Wheel Components (X88 or
Z88) • S70L Steering Wheel Controls
Switch - Left (Z88)
S70R Steering Wheel Controls Switch - — In the passenger compartment, on the right side
Right of the steering wheel
• Steering Wheel Components (Z75) • S70R Steering Wheel Controls
Switch - Right (X88)
• Steering Wheel Components (X88 or
Z88) • S70R Steering Wheel Controls
Switch - Right (Z88)
S71 Steering Column Tilt and N38 In the passenger compartment, forward, left side, — —
Telescope Switch on the steering column
S72 Sunroof Switch CF5 In the passenger compartment, overhead, Overhead Console Components S72 Sunroof Switch
forward of center, in the overhead console
S74 Tow/Haul Mode Switch — In the passenger compartment, part of the Steering Column Components (2 of 2) —
transmission shift lever
S76 Trailer Brake Control Switch JL1 In the passenger compartment, forward, left side, S76 Trailer Brake Control Switch
on instrument panel, left of steering column
• Front of Instrument Panel
Components (X88/Z88 with D07/DCK)
S78 Turn Signal/Multifunction Switch — In the passenger compartment, left side, on the Steering Column Components (2 of 2)
left side of the steering column
• S78 Turn Signal/Multifunction Switch
X1
S79D Window Switch - Driver — In the passenger compartment, behind the driver S79D Window Switch - Driver
door trim panel, center of the door
• Driver Door Components (X88 or
Z88)
S79RR Window Switch - Right Rear — In the passenger compartment, on the right rear S79RR Window Switch - Right Rear
door trim panel, center of the door
• Right Rear Door Components (Z75)
• Right Rear Door Components (X88 or
Z88)
S91 Park Brake Control Switch J71 In the passenger compartment, left side, on the Front of Instrument Panel Components S91 Park Brake Control Switch
instrument panel knee bolster (Z75)
S135 Rollover Protection Disable C9I In the passenger compartment, center, in Front of Instrument Panel Components S135 Rollover Protection Disable
Switch instrument panel (X88/Z88 without D07/DCK) Switch
S140 Media Disc Eject Switch Z75 In the passenger compartment, on the face of the Front of Instrument Panel Components S140 Media Disc Eject Switch
instrument panel center stack below the (Z75)
radio/HVAC controls
S141 Liftgate Window Unlatch Switch — At the rear of the vehicle, in the liftgate, center, Rear of Vehicle Components (Z75) S141 Liftgate Window Unlatch Switch
in the top right of the license plate bezel
S143L Folding Seat Control Switch - 2nd ATN or ATT In the passenger compartment, left side, on C- — S143L Folding Seat Control Switch -
Row Left Pillar trim 2nd Row Left
S143R Folding Seat Control Switch - 2nd ATN or ATT In the passenger compartment, right side, on C- — S143R Folding Seat Control Switch -
Row Right Pillar trim 2nd Row Right (ATN/ATT)
S144A Folding Seat Control Switch - ATN or ATT In the rear compartment, right side, in the trim — S144A Folding Seat Control Switch -
Rear Compartment 2nd Row under the quarter window glass Rear Compartment 2nd Row
S144B Folding Seat Control Switch - AS8 In the rear compartment, right side, in the trim — S144B Folding Seat Control Switch -
Rear Compartment 3rd Row under the quarter window glass Rear Compartment 3rd Row
T1 Accessory DC/AC Power Inverter KI4 or KI5 In the passenger compartment, Inside the T1 Accessory DC/AC Power Inverter
Module instrument panel, right side of the steering
• Back of Instrument Panel Module
Components (X88/Z88 with D07/DCK)
column
• Back of Instrument Panel
Components (Z75)
T3 Audio Amplifier UQA, UQH or UQS In the rear compartment, behind the left rear Left Rear Cargo Area Components
quarter trim.
• T3 Audio Amplifier X1
(UQA/UQH/UQS+AZ3)
• T3 Audio Amplifier X1
(UQA/UQH/UQS+D07)
• T3 Audio Amplifier X2
(UQA/UQH/UQS)
• T3 Audio Amplifier X3
(UQA/UQH/UQS)
• T3 Audio Amplifier X4
(UQA/UQH/UQS)
T4G Cellular Phone, Navigation, and — Outside of the vehicle, on the roof, left front, near —
Digital Radio Antenna windshield
• Front of Vehicle Components (X88)
• Front of Vehicle Components (Z88)
• Front of Vehicle Components (Z75)
T4M Radio Antenna — In the rear compartment, right side, top of the — —
right rear quarter glass
T4U Auxiliary Audio Transmitter AYE In the passenger compartment, in the floor — —
Antenna console, left side under the instrument panel
T7L Headlamp Ballast - Left T4F Outside the vehicle, left front corner, inside the —
headlamp
• Headlamp Components (X88)
• Headlamp Components (Z88)
T7R Headlamp Ballast - Right T4F Outside the vehicle, right front corner, inside the —
headlamp
• Headlamp Components (X88)
• Headlamp Components (Z88)
T8A Ignition Coil 1 — In the engine compartment, at the top front, left
side of the engine, near cylinder 1
• Left Rear Side of Engine • T8A Ignition Coil 1 (L83/L86)
Components (L96)
• T8A Ignition Coil 1 (L86)
• Top of Engine Components (L83 or
L86) • T8A Ignition Coil 1 (L96)
T8G Ignition Coil 7 — In the engine compartment, at the top rear, left
side of the engine, near cylinder 7
• Left Rear Side of Engine • T8G Ignition Coil 7 (L83/L86)
Components (L96)
• T8G Ignition Coil 7 (L86)
• Top of Engine Components (L83 or
L86) • T8G Ignition Coil 7 (L96)
T8H Ignition Coil 8 — In the engine compartment, at the top rear, right
side of the engine, near cylinder 8
• Right Rear Side of Engine • T8H Ignition Coil 8 (L83/L86)
Components (L96)
• T8H Ignition Coil 8 (L86)
• Top of Engine Components (L83 or
L86) • T8H Ignition Coil 8 (L96)
T10E Keyless Entry Antenna - Rear ATH or BTM In the passenger compartment, left side, just — T10E Keyless Entry Antenna - Rear
Compartment rearward of the C-pillar, on the floor Compartment
T10G Keyless Entry Antenna - Rear ATH or BTM At the rear of the vehicle, left of center, mounted Behind Rear Fascia Components T10G Keyless Entry Antenna - Rear
Fascia on the back of the rear fascia, left of center Fascia
T10J Keyless Entry Antenna - Center ATH or BTM In the passenger compartment, in the instrument Front of Instrument Panel Components T10J Keyless Entry Antenna - Center
Console Front panel under the center stack info display (X88/Z88 with D07/DCK) Console Front
T10K Keyless Entry Antenna - Center ATH or BTM In the passenger compartment, at the back of the T10K Keyless Entry Antenna - Center
Console Rear floor console near the auxiliary HVAC controls
• Center Console Rear Component Console Rear
Views (X88/Z88)
T10M Keyless Entry Antenna - Driver ATH or BTM Outside the vehicle, on the driver door, part of — —
Door Handle the door handle assembly
T10N Keyless Entry Antenna - ATH or BTM Outside the vehicle, on the passenger door, part — —
Passenger Door Handle of the door handle assembly
T22 Mobile Device Wireless Charger K4C In the passenger compartment, forward of center, T22 Mobile Device Wireless Charger
Module in the floor console bin lid.
• Center Console Top Component Module
Views (X88/Z88)
T23 Radio Antenna Amplifier — In the rear compartment, right side, above rear — —
quarter glass, behind the headliner
X50A Fuse Block - Underhood — In the engine compartment, front left rear Left Side of Engine Compartment Electrical Center Identification Views
Component View
X50D Fuse Block - Battery — In the engine compartment, top right, on the Right Rear of Engine Compartment Electrical Center Identification Views
battery Components (2 of 2)
X50E Fuse Block - Battery Auxiliary 5W4 or 9C1 In the engine compartment, front left, on the — Electrical Center Identification Views
auxiliary battery
X51L Fuse Block - Instrument Panel — In the passenger compartment, left side of the Left Front of Passenger Compartment Electrical Center Identification Views
Left instrument panel, behind access panel Views (Z75)
X51R Fuse Block - Instrument Panel — In the passenger compartment, right side of the — Electrical Center Identification Views
Right instrument panel, behind access panel
X53A Fuse Block - Rear Body — In the rear compartment, left side, behind the — Electrical Center Identification Views
access door in the rear compartment trim
X55X Fuse Holder - Video Display AYE In the passenger compartment, underside of — Electrical Center Identification Views
instrument panel, left side, above the lower
instrument panel close out panel
X61A Junction Block - Instrument — In the passenger compartment, under the Electrical Center Identification Views
Panel instrument panel, left side footwell
• Behind Left Side of Instrument Panel
Components (1 of 2)
X80D Accessory Power Receptacle - D07 or DCK In the passenger compartment, between the
Center Console Compartment driver and passenger seat, in the center floor
• Center Console Top Component • X80D Accessory Power Receptacle -
Views (Z75) Center Console Compartment
console compartment
((X88/Z88)+D07)
• Center Console Internal Component
Views (X88/Z88) • X80D Accessory Power Receptacle -
Center Console Compartment
• Center Seat Components (AZ3) ((X88/Z88)+DCK)
X80E Accessory Power Receptacle - AZ3 In the passenger compartment, in the front center Center Seat Components (AZ3) X80E Accessory Power Receptacle -
Center Seat seat, at the rear of the center seat Center Seat
X80G Accessory Power Receptacle - D07 or DCK In the passenger compartment, on top of the floor
Instrument Panel console, below the info display on the center
• Front of Instrument Panel • X80G Accessory Power Receptacle -
Components (X88/Z88 without Instrument Panel ((X88/Z88)+D07)
stack
D07/DCK)
• X80G Accessory Power Receptacle -
• Center Console Top Component Instrument Panel ((X88/Z88)+DCK)
Views (Z75)
• X80G Accessory Power Receptacle -
• Center Console Top Component Instrument Panel (AZ3)
Views (X88/Z88)
• X80G Accessory Power Receptacle -
Instrument Panel (Z75)
X80G Accessory Power Receptacle - AZ3 In the passenger compartment, in the instrument
Instrument Panel panel below the info display on the center stack
• Front of Instrument Panel • X80G Accessory Power Receptacle -
Components (X88/Z88 without Instrument Panel ((X88/Z88)+D07)
D07/DCK)
• X80G Accessory Power Receptacle -
• Center Console Top Component Instrument Panel ((X88/Z88)+DCK)
Views (Z75)
• X80G Accessory Power Receptacle -
• Center Console Top Component Instrument Panel (AZ3)
Views (X88/Z88)
• X80G Accessory Power Receptacle -
Instrument Panel (Z75)
X80L Accessory Power Receptacle - D07 In the passenger compartment, at the rear of the X80L Accessory Power Receptacle -
Center Console Rear floor center console
• Center Console Rear Component Center Console Rear
Views (Z75)
X80RL Accessory Power Receptacle - — In the passenger compartment, rear, left side, — X80RL Accessory Power Receptacle -
Rear Compartment Left behind the C-Pillar in the molded in arm rest of Rear Compartment Left
the quarter panel trim.
X80RR Accessory Power Receptacle - — In the rear compartment, right side, in the molded — X80RR Accessory Power Receptacle -
Rear Compartment Right quarter panel trim, underneath the rear quarter Rear Compartment Right
glass
X81B Accessory Power Receptacle - KI5 with AZ3 In the passenger compartment, center of the — —
220V AC instrument panel, below the HVAC controls
X81B Accessory Power Receptacle - KI5 with D07 or DCK In the passenger compartment, at the rear of the — —
220V AC floor center console
X81 Accessory Power Receptacle - KI4 with D07 or DCK In the passenger compartment, at the rear of the
110V AC floor center console
• Center Console Rear Component • X81 Accessory Power Receptacle -
Views (X88/Z88) 110V AC X1 ((X88/Z88)+D07)
X82 Audio/Video Input Adapter U42 with D07 In the passenger compartment, at the rear of the X82 Audio/Video Input Adapter X1
floor center console
• Center Console Rear Component
Views (Z75)
X83 Auxiliary Audio Input AZ3 In the passenger compartment, in the center seat
compartment
• Center Console Internal Component • X83 Auxiliary Audio Input X1
Views (X88/Z88) ((X88/Z88)+D07+IO3)
X84 Data Link Connector — In the passenger compartment, left side, at the X84 Data Link Connector
bottom of the driver side of the instrument panel
• Front of Instrument Panel
Components (Z75)
X85 Steering Wheel Air Bag Coil — In the passenger compartment, left side, on the X85 Steering Wheel Air Bag Coil
steering column, behind the steering wheel
• Steering Column Components (2 of
2)
X88 Trailer Connector without VQ9 On the vehicle exterior, at the rear of the vehicle, Chassis Harness Routing X88 Trailer Connector
left of the license plate
X92A USB Receptacle - Instrument IO5 or IO6 In the passenger compartment, forward and — —
Panel Compartment center, in the instrument panel, behind the screen
of the P17 Info Display
X92 USB Receptacle D07 with IO5 or IO6 In the passenger compartment, at the top of the
floor console, below instrument panel center
• Center Console Top Component • X92 USB Receptacle (X88/Z88)
Views (Z75)
stack • X92 USB Receptacle (Z75)
• Center Console Top Component
Views (X88/Z88)
X100 Front Bumper Harness to X88 or Z88 At the front of the vehicle, right of center, on top Forward Lamp Harness Routing - Right X100 Front Bumper Harness to
Forward Lamp Harness (16 of the core support Engine Compartment Forward Lamp Harness (X88/Z88)
Cavities)
X100 Front Bumper Harness to Z75 At the front of the vehicle, right of center, on top Forward Lamp Harness Routing - Right X100 Front Bumper Harness to
Forward Lamp Harness (40 of the core support Engine Compartment Forward Lamp Harness (Z75+AVF)
Cavities)
X104 Front Bumper Harness to Right Z75 At the front of the vehicle, right side, behind the — X104 Front Fascia Harness to Right
Multifunction Lamp Harness (8 front bumper Multifunction Lamp Harness
Cavities)
X106 Aero Shutter Harness to Forward Z75 At the front of the vehicle, at center, behind — X106 Aero Shutter Jumper Harness to
Lamp Harness (6 Cavities) upper grille at hood latch Forward Lamp Harness
X110 Forward Lamp Harness to Left — In the engine compartment, at the rear of the left Forward Lamp Harness Routing - Left
Headlamp Harness (8 Cavities) headlamp assembly Engine Compartment
• X110 Forward Lamp Harness to Left
Headlamp Harness (X88)
X111 Front Axle Jumper Harness to NP0 or NQH In the engine compartment, left front, above the X111 Transfer Case Harness to Engine
Engine Harness (4 Cavities) front axle
• Engine Harness Routing - Left Rear Harness
(L96)
X115 Engine Harness to Body Harness — In the front of the engine compartment, left side, X115 Engine Harness to Body Harness
(48 Cavities) at front of Underhood Fuse Block
• Engine Harness Routing - Left Rear
(L96)
X119 Body Harness to Brake Clutch — In the passenger compartment, left side of the Body Harness Routing - Left Front of X119 Body Harness to Brake Clutch
Jumper Harness (16 Cavities) instrument panel, on IP junction block Passenger Compartment Jumper Harness
X120 Forward Lamp Harness to Right — In the engine compartment, at the rear of the Forward Lamp Harness Routing - Right
Headlamp Harness (8 Cavities) right headlamp assembly Engine Compartment
• X120 Forward Lamp Harness to
Right Headlamp Harness (X88)
X122 Forward Lamp Harness to 6J7 In the engine compartment, towards the front, Forward Lamp Harness Routing - Right X122 Forward Lamp Harness to
Forward Lamp Harness (6 right side, forward of the right hand wheel well Engine Compartment Forward Lamp Harness
Cavities)
X125 Engine Harness to Chassis — In the engine compartment, on the top left of the X125 Engine Harness to Chassis
Harness (20 Cavities) frame rail, near the top of the left front shock
• Front Axle Harness Routing Harness
• Engine Harness Routing - Left Front
(L83 or L86)
X139 Engine Harness to Forward Lamp — in the engine compartment, left side, near center,
Harness (8 Cavities) inboard of underhood fuse block, below X125
• Forward Lamp Harness Routing - Left • X139 Engine Harness to Forward
Engine Compartment Lamp Harness (L83/L86)
X154 Engine Harness to Camshaft — In the engine compartment, Front of engine, near Engine Harness Routing - Left Front X154 Engine Harness to Camshaft
Jumper Harness (8 Cavities) power steering pulley (L83 or L86) Jumper Harness
X158 Auxiliary Battery Harness to 5W4 or 9C1 In the engine compartment, right of center — X158 Battery Harness to Engine
Engine Harness (6 Cavities) Harness
X160 Engine Harness to Odd Fuel L83 or L86 In the engine compartment, rear of the engine Engine Harness Routing - Right Rear X160 Engine Harness to Odd Fuel
Injector Harness (12 Cavities) near the top center (L83 or L86) Injector Harness
X161 Engine Harness to Even Fuel L83 or L86 In the engine compartment, rear of the engine Engine Harness Routing - Right Rear X161 Engine Harness to Even Fuel
Injector Harness (12 Cavities) near the top right (L83 or L86) Injector Harness
X170 Engine Harness to Ignition Coil L96 On the engine, near the odd ignition coils — X170 Engine Harness to Ignition Coil
(Odd) Harness (8 Cavities) (Odd) Harness (L96)
X171 Engine Harness to Ignition Coil L96 On the engine, near the even ignition coils Engine Harness Routing - Left Rear X171 Engine Harness to Ignition Coil
(Even) Harness (8 Cavities) (L96) (Even) Harness
X175 Engine Harness to Transmission M5U Under the vehicle, forward of center, on the right Engine Harness Routing - Right Rear X175 Engine Harness to Transmission
Harness (36 Cavities) side of the transmission, forward of the transfer (L83 or L86) Harness (M5U)
case
X182 Chassis Harness to Power — In the engine compartment, front left side, on the Chassis Harness Routing X182 Chassis Harness to Power
Steering Jumper Harness (12 cross rail, on the left frame rail. Steering Jumper Harness
Cavities)
X183 Battery Harness to Power — In the engine compartment, front, on the cross — —
Steering Jumper Harness (2 rail, below the crank shaft pulley
Cavities)
X185 Chassis Harness to Body — In the rear of the engine compartment, right rear X185 Chassis Harness to Body
Harness (40 Cavities) of the under hood fuse block
• Chassis Harness Routing Harness
• Body Harness Routing - Engine
Compartment Top
X195 Body Harness to Underhood 5W4 or 9C1 In the engine compartment, right side — X195 Body Harness to Underhood
Harness (4 Cavities) Harness
X201 Steering Column Harness to — In the passenger compartment, behind the left Instrument Panel Harness Routing - X201 Steering Column Harness to
Instrument Panel Harness (42 side of the instrument panel, above the Body Rear of Instrument Panel Instrument Panel Harness
Cavities) Control Module
X203 Headliner Harness to Instrument — In the passenger compartment, forward, left side, X203 Headliner Harness to Instrument
Panel Harness (12 Cavities) in the top of the instrument panel near the left
• Instrument Panel Harness Routing - Panel Harness
Rear of Instrument Panel
instrument panel speaker
• Headliner Harness Routing
X205 Instrument Panel Harness to — In the passenger compartment, behind the right Instrument Panel Harness Routing - X205 Instrument Panel Harness to
Passenger Air Bag Jumper side of the instrument panel, right side of blower Rear of Instrument Panel Passenger Air Bag Jumper Harness
Harness (4 Cavities) motor HVAC caser
X212 GPS Antenna Jumper COAX to CV3 with UE1 In the passenger compartment, forward, right of — —
Instrument Panel Harness COAX center, in instrument panel near K73
(1 Cavity)
X215 HVAC Harness to Instrument — In the passenger compartment, behind the upper X215 HVAC Harness to Instrument
Panel Harness (14 Cavities) right side of the instrument panel defroster
• HVAC Assembly Harness Routing Panel Harness
deflector • Instrument Panel Harness Routing -
Rear of Instrument Panel
X216 Body Harness to HVAC Harness — In the passenger compartment, behind the lower X216 Body Harness to HVAC Harness
(20 Cavities) right side of the instrument panel glove box, on
• Body Harness Routing - Right Front
of Passenger Compartment
the HVAC case
• HVAC Assembly Harness Routing
X217 Body Harness to HVAC Harness — In the passenger compartment, behind the lower X217 Body Harness to HVAC Harness
(2 Cavities) right side of the instrument panel glove box, on
• Body Harness Routing - Right Front
of Passenger Compartment
the HVAC case
• HVAC Assembly Harness Routing
X221 Instrument Panel COAX to — In the passenger compartment, forward, right — —
Headliner Harness COAX (1 side, top of instrument panel, under defrost
Cavity) deflector, at the Navigation Antenna Splitter
X222 Instrument Panel Harness COAX UE1 In the passenger compartment, forward, right Instrument Panel Harness Routing -
to A-Pillar Harness COAX (2 side, top of instrument panel, below the defrost Rear of Instrument Panel
• X222 Instrument Panel COAX to A-
Pillar Harness COAX (VV4 or
Cavities) deflector
CV3)+IO6
X225 Body Harness to Instrument — In the passenger compartment, forward, right X225 Body Harness to Instrument
Panel Harness (42 Cavities) side, below the Instrument panel, in the driver
• Body Harness Routing - Left Front of Panel Harness
Passenger Compartment
foot well, behind the kick panel
• Instrument Panel Harness Routing -
Rear of Instrument Panel
X238 Body Harness USB to Instrument AZ3 In the passenger compartment, front, below right Instrument Panel Harness Routing - X238 Body Harness USB to
Panel Harness USB side of Instrument Panel, behind kick panel Rear of Instrument Panel Instrument Panel Harness USB (AZ3)
X245 Instrument Panel Harness COAX U2K or U2M In the passenger compartment, forward, right — —
to A-Pillar Harness COAX (1 side, top of instrument panel, below the defrost
Cavity) deflector, at the Navigation Splitter
X271 Instrument Panel Harness to WX7 In the front of the passenger compartment, in the Instrument Panel Harness Routing - X271 Instrument Panel Harness to
Instrument Panel Harness (8 instrument panel Bottom Center Instrument Panel Harness
Cavities)
X272 Instrument Panel Harness to 6J3 or 6J7 In the passenger compartment, under the center Instrument Panel Harness Routing - X272 Instrument Panel Harness to
Upfitter Jumper (6 Cavities) of the instrument panel Bottom Center Upfitter Jumper Harness
X275 Instrument Panel Harness to — In the passenger compartment, right side, below X275 Instrument Panel Harness to
Body Harness (42 Cavities) the Instrument panel, in the passenger foot well,
• Instrument Panel Harness Routing - Body Harness
Rear of Instrument Panel
behind the kick panel
• Body Harness Routing - Right Front
of Passenger Compartment
X295 Instrument Panel Harness to Z75 In the passenger compartment, about 11cm (4 — X295 Instrument Panel Harness to
Body Harness (12 Cavities) inches) from the breakout for the data link Body Harness (Z75)
connector
X300 Instrument Panel Harness to D07 In the passenger compartment, underneath floor X300 Instrument Panel Harness to
Floor Console Harness (42 console cup holders
• Floor Console Harness Routing - Top Floor Console Harness
(X88 or Z88)
Cavities)
• Floor Console Harness Routing -
Bottom Front (Z75)
X301 Instrument Panel Harness USB DCK/D07 with U42 In the passenger compartment, underneath floor — X301 Instrument Panel Harness USB
to Floor console Harness USB console cup holders to Floor console Harness USB
(D07/DCK with U42)
X302 Floor Console Harness USB to D07 In the passenger compartment, underneath floor Instrument Panel Harness Routing -
Instrument Panel Harness USB console cup holders, next to X300 Bottom Center
• X302 Floor Console Harness USB to
Instrument Panel Harness USB
(D07/DCK with U42)
X303 Floor Console Harness USB to D07 In the passenger compartment, front center, Instrument Panel Harness Routing - X303 Floor Console Extension
Instrument Panel Harness USB underneath floor console cup holders, next to Bottom Center Harness USB to Instrument Panel
X300 Harness USB (D07/DCK with U42)
X304 Body Harness USB to Center AZ3 In the passenger compartment, under the front X304 Body Harness USB to Center
Seat Harness USB center seat
• Floor Console Harness Routing - Seat Harness USB (AZ3)
Bottom Front (Z75)
X305 Instrument Panel Harness to KI5 In the passenger compartment, in the instrument — X305 Instrument Panel Harness to
Power Receptacle Jumper panel Instrument Panel Extension Harness
Harness (12 Cavities)
X306 Instrument Panel Harness to KI4 or KI5 with D07 In the passenger compartment, center, X306 Instrument Panel Harness to
Floor Console Harness (6 underneath floor console cup holders, next to
• Instrument Panel Harness Routing - Floor Console Harness
Bottom Center
Cavities) X300
• Floor Console Harness Routing -
Bottom Front (Z75)
X307 Floor Console Harness to Floor X88 or Z88 with D07 In the passenger compartment, center, Floor Console Harness Routing - Top X307 Floor Console Harness to Floor
Console Harness (14 Cavities) underneath the floor console cup holders, next to (X88 or Z88) Console Extension Harness
X300
X310 Driver Seat Harness to Body — In the passenger compartment, left side, under
Harness (48 Cavities) the driver seat
• Body Harness Routing - Left Front of • X310 Driver Seat Cushion Harness
Passenger Compartment to Body Harness X88/Z88-
(AG1/A45/KQV)
• Driver Seat Harness Routing
• X310 Driver Seat Cushion Harness
to Body Harness
X88/Z88+(AG1/A45/KQV)
X311 Driver Seat Back Harness to without ULT In the passenger compartment, inside the driver Driver Seat Harness Routing X311 Driver Seat Back Harness to
Driver Seat Cushion Harness (6 seat, under the cushion Driver Seat Cushion Harness
Cavities)
X312 Driver Seat Back Harness to ULT In the passenger compartment, inside the driver Driver Seat Harness Routing
Driver Seat Cushion Harness (14 seat, under the cushion
• X312 Driver Seat Back Harness to
Driver Seat Cushion Harness
Cavities)
(Z75+ULT)
X312 Driver Seat Back Harness to AG1 without ULT In the passenger compartment, inside the driver Driver Seat Harness Routing
Driver Seat Cushion Harness (12 seat, under the cushion
• X312 Driver Seat Back Harness to
Driver Seat Cushion Harness
Cavities)
(Z75+ULT)
X313 Power Mat Jumper Harness to DCK In the passenger compartment, forward of center, X313 Floor Console Extension
Floor Console Harness (3 in the floor console
• Floor Console Harness Routing - Harness to Floor Console Harness
Rear (X88 or Z88)
Cavities)
• Floor Console Harness Routing -
Bottom Front (Z75)
X315 Headliner Harness to Body NKC, UGN or UTT In the passenger compartment, forward, left side, X315 Headliner Harness to Body
Harness (16 Cavities) behind left instrument panel access panel, near
• Headliner Harness Routing Harness
left instrument panel fuse block • Body Harness Routing - Left Front of
Passenger Compartment
X316 Headliner Harness to Overhead — In the passenger compartment, in the headliner, X316 Headliner Harness to Overhead
Console Harness (26 Cavities) above the over head console
• Headliner Harness Routing Console Harness
• Overhead Console Harness Routing
X318 Rain Sensor Jumper Harness to — In the passenger compartment, overhead, behind A-Pillar Harness Routing - Right X318 Rain Sensor Jumper Harness to
A-Pillar Harness (3 Cavities) the inside rear view mirror Passenger Compartment Headliner Harness
X319 A-Pillar Harness to Sunroof CF5 or TRW In the passenger compartment, above the X319 A-Pillar Harness to Headliner
Harness (2 Cavities) overhead console
• Overhead Console Harness Routing Harness
• A-Pillar Harness Routing - Right
Passenger Compartment
X320 Passenger Seat Harness to Body — In the passenger compartment, right side, under Body Harness Routing - Right Front of
Harness (48 Cavities) the passenger seat Passenger Compartment
• X320 Passenger Seat Cushion
Harness to Body Harness X88/Z88-
(AG1/A45/KQV)
X321 Passenger Seat Back Harness to without ULT In the passenger compartment, inside the — X321 Passenger Seat Back Harness
Passenger Seat Cushion passenger seat, under the cushion to Passenger Seat Cushion Harness
Harness (6 Cavities)
X322 Passenger Seat Back Harness to AG2 without ULT In the passenger compartment, inside the —
Passenger Seat Cushion passenger seat, under the cushion
• X322 Passenger Seat Back Harness
to Passenger Seat Cushion Harness
Harness (6 Cavities)
(Z75+ULT)
X322 Passenger Seat Back Harness to without AG2 or ULT In the passenger compartment, inside the —
Passenger Seat Cushion passenger seat, under the cushion
• X322 Passenger Seat Back Harness
to Passenger Seat Cushion Harness
Harness (2 Cavities)
(Z75+ULT)
X324 Sunroof Harness to Overhead CF5 In the passenger compartment, front of center, Overhead Console Harness Routing X324 Sunroof Harness to Headliner
Console Harness (10 Cavities) overhead, in the overhead console Harness
X338 Body Harness to 3rd Row Seat AS8 In the passenger compartment left side, under X338 Body Harness to 3rd Row Seat
Left Harness (6 Cavities) the third row seat cushion, at the left seat frame
• Body Harness Routing - Left Middle Left Harness
of Passenger Compartment
to floor mount
• Third Row Seat Harness Routing
X340 3rd Row Seat Right Harness to AS8 In the passenger compartment, at the rear, inside Third Row Seat Harness Routing X340 3rd Row Seat Right Harness to
3rd Row Seat Left Harness (6 the 3rd row seat, on seat frame between left and 3rd Row Seat Left Harness (AS8)
Cavities) right seats
X348 Center Seat Harness to Body AZ3 In the passenger compartment, forward of center, — X348 Center Seat Harness to Body
Harness (16 Cavities) under the center seat Harness (AZ3+AVF)
X353 Headliner Jumper COAX to (-SWB)+DRZ In the passenger compartment, In the headliner — X353 Headliner Jumper COAX to
Headliner COAX Headliner COAX (-SWB)+DRZ
X354 Liftgate Jumper COAX to (SWB)+DRZ In the passenger compartment, In the headliner, — X354 Liftgate COAX to Headliner
Headliner Jumper COAX near the liftgate Jumper COAX (SWB)+DRZ
X371 Accessory Signal Harness 1A to AYE In the passenger compartment, Bottom of driver — —
Accessory Signal Harness 3A (6 seat, right side, where the seat back meets the
Cavities) seat cushion
X373 Accessory Signal Harness 2A to AYE In the passenger compartment, Bottom of driver — —
Accessory Signal Harness 3A (6 seat, right side, where the seat back meets the
Cavities) seat cushion
X378 Body Harness to 2nd Row Seat ATN or ATT In the passenger compartment, near center, right Second Row Seat Harness Routing X378 Body Harness to Rear Seat
Jumper Harness (8 Cavities) side, underneath second row seat, under carpet Harness
X380 Body Harness to Driver Roof Rail — In the passenger compartment, at the left D- Body Harness Routing - Left Rear of X380 Body Harness to Driver Roof Rail
Air Bag Jumper (2 Cavities) pillar, near the headliner Passenger Compartment Airbag Jumper Harness
X390 Body Harness to Passenger Roof — In the passenger compartment, at the right D- Body Harness Routing - Right Rear of X390 Body Harness to Driver Roof Rail
Rail Air Bag Jumper (2 Cavities) pillar, near the headliner Passenger Compartment Air Bag Jumper Harness
X410 Left Tail Lamp Jumper to — At the rear of the vehicle, left corner, underneath, Chassis Harness Routing X410 Left Tail Lamp Jumper Harness
Chassis Harness (6 Cavities) on left frame rail to Chassis Harness
X420 Right Tail Lamp Jumper to — At the rear of the vehicle, right corner, Chassis Harness Routing X420 Right Tail Lamp Jumper Harness
Chassis Harness (6 Cavities) underneath, on right frame rail to Chassis Harness
X421 Antenna Jumper Harness COAX — In the rear compartment right side, above the rear — —
to Headliner Harness COAX (1 quarter glass, above the headliner
Cavity)
X423 Liftgate Jumper COAX to — In the passenger compartment, In the headliner, — X423 Liftgate COAX to Headliner
Headliner COAX near the liftgate COAX (-SWB)+DRZ
X424 Liftgate Jumper Coax to Liftgate — In the liftgate, behind the trim, near the top close — X424 Liftgate Jumper Coax to Liftgate
Coax to the high mount stop lamp Coax (DRZ)
X485 CHMSL Harness to Body — In the rear compartment, at the rear, right of — X485 Center High Mounted Stop Lamp
Harness(2 Cavities) center, attached to the roof above the headliner Jumper Harness to Body Harness
X486 Body Harness to Rear Dome without SWB In the rear compartment, at the rear, right side, at Body Harness Routing - Right Rear of X486 Body Harness to Headliner
Lamp Jumper Harness (2 the top of the D-pillar, above the headliner Passenger Compartment Harness
Cavities)
X487 Body Harness to Rear HVAC — In the rear compartment, right side, behind the Body Harness Routing - Right Rear of X487 Body Harness to Auxiliary HVAC
Jumper Harness (14 Cavities) quarter trim on rear HVAC unit Passenger Compartment Jumper Harness
X490 Body Harness to Body Harness — In the rear compartment, center, rear of vehicle, X490 Body Harness to Body Harness
(8 Cavities) above the headliner
• Body Harness Routing - Left Rear of
Passenger Compartment
X500 Driver Door Harness to Body — In the passenger compartment, forward, left side, X500 Driver Door Harness to Body
Harness (41 Cavities) in the driver door jam, between door hinges
• Driver Door Harness Routing Harness
• Body Harness Routing - Left Front of
Passenger Compartment
X505 Driver Door Harness to Driver — In the driver door, behind the driver door panel Driver Door Harness Routing X505 Driver Door Harness to Driver
Door Trim Harness (48 Cavities) Door Trim Harness
X510 OSRVM Harness to Door Driver — At the front of the driver door, behind driver door Driver Door Harness Routing X510 Outside Rearview Mirror Harness
Harness (18 Cavities) trim panel to Driver Door Harness
X515 Left OSRVM Camera Jumper to UVH At the front of the left front door, inside the — X515 Left Outside Rearview Mirror
Door Driver Harness (7 Cavities) Outside Rearview Mirror Camera Jumper Harness to Driver
Door Harness
X525 Driver OSRVM Harness to Driver — At the front of the left front door, inside the — —
OSRVM Glass Harness (6 Outside Rearview Mirror
Cavities)
X600 Passenger Door Harness to Body — In the passenger compartment, forward, right X600 Passenger Door Harness to
Harness (41 Cavities) side, in the passenger door jam, between door
• Body Harness Routing - Right Front Body Harness
of Passenger Compartment
hinges
• Passenger Door Harness Routing
X605 Passenger Door Harness to — In the passenger door, behind the passenger door Passenger Door Harness Routing X605 Passenger Door Harness to
Passenger Door Trim Harness panel Passenger Door Trim Harness
(48 Cavities)
X610 OSRVM Harness to Door — At the front of the passenger door, behind — X610 Outside Rearview Mirror Harness
Passenger Harness (18 Cavities) passenger door trim panel to Passenger Door Harness
X615 Right OSRVM Camera Jumper to UVH At the front of the right front door, inside the — X615 Outside Rearview Mirror Jumper
Door Driver Harness (7 Cavities) Outside Rearview Mirror Harness to Passenger Door Harness
X625 Passenger OSRVM Harness to — At the front of the left front door, inside the — —
Passenger OSRVM Glass Outside Rearview Mirror
Harness (4 Cavities)
X700 Left Rear Door Harness to Body — In the passenger compartment, behind the left B- X700 Left Rear Door Harness to Body
Harness (20 Cavities) pillar, near the middle
• Left Rear Door Harness Routing Harness
• Body Harness Routing - Left Front of
Passenger Compartment
X705 Left Rear Door Harness to Left Z75 In the left rear door, behind the door panel Left Rear Door Harness Routing X705 Left Rear Door Harness to Left
Rear Door Trim Harness (6 Rear Door Trim Harness
Cavities)
X800 Right Rear Door Harness to Body — In the passenger compartment, behind the right X800 Right Rear Door Harness to Body
Harness (20 Cavities) B-pillar, near the middle
• Right Rear Door Harness Routing Harness
• Body Harness Routing - Right Front
of Passenger Compartment
X805 Right Rear Door Harness to Right Z75 In the right rear door, behind the door panel Right Rear Door Harness Routing —
Rear Door Trim Harness (6
Cavities)
G100 Auxiliary Battery Negative L96 or L83 with 5W4 or 9C1 In the engine compartment, front left of center, —
Harness on front of the engine block, rearward of the
• G100 (L83 with 5W4 or 9C1)
auxiliary battery • G100, G110 and G120 (L96)
G101 Forward Lamp Harness — Behind front fascia, lower left of the radiator core G101 —
support, forward of the left side frame mount to
the core support
G102 Forward Lamp Harness — Behind front fascia, lower right of the radiator G102 —
core support, forward of the right side frame
mount to the core support
G103 Battery Negative Harness — In the engine compartment, right of center, on the G103 and G125 (L83 or L86) —
right side frame rail, below battery
G110 Engine Harness L83 or L86 In the engine compartment, on the left side of the —
engine block near the front, behind the water
• G110 (L83 or L86)
pump • G100, G110 and G120 (L96)
G110 Engine Harness L96 In the engine compartment, on the left side of the —
engine block, at the bottom near the front, behind
• G110 (L83 or L86)
the power steering pump • G100, G110 and G120 (L96)
G120 Engine Harness L96 In the engine compartment, on the right side of G100, G110 and G120 (L96) —
the engine block near the top, at the front
G121 Chassis Harness — Under vehicle, outboard side of left frame rail, G121 —
rearward side of the front body mount to chassis
G125 Electric Power Steering Harness L83 or L86 In the engine compartment, front right of center, G103 and G125 (L83 or L86) —
on the front of the engine, above the A/C
compressor
G130 Engine Harness L83 or L86 In the engine compartment, rear left of center, on G130 and G140 (L83 or L86) —
the engine, back side of left cylinder head
G140 Engine Harness L83 or L86 In the engine compartment, rear right of center, G130 and G140 (L83 or L86) —
on the engine, back side of right cylinder head
G141 Battery Negative Harness L83 or L86 In the engine compartment, rear right of center, G141 (L83 or L86) —
on the engine, back side of right cylinder head
G210 Instrument Panel Harness — In the passenger compartment, front right of G210 —
center, top side of instrument panel, below trim,
inboard of right A-Pillar
G218 Instrument Panel Harness — In the passenger compartment, front left of G218 —
center, top side of instrument panel, below trim,
inboard of left A-Pillar
G311 Body Harness — In the passenger compartment, left middle, base G311 and G325 —
of left side B-Pillar
G312 Body harness — In the passenger compartment, right middle, G312 and G327 —
base of right side B-Pillar
G325 Body Harness — In the passenger compartment, left middle, on G311 and G325 —
floor below driver seat, near X310
G400 Chassis Harness — Under vehicle, inboard of left frame rail, top side G400 —
of rear most cross member
G402 Body Harness — In the luggage compartment, right rear, on right G402 —
side D-Pillar, near bottom of quarter window
J101 Front Bumper Harness T3U At front of vehicle, middle, approximately 16cm — —
(6.25 inches) forward of the harness break-out for
the right fog lamp.
J103 Front Bumper Harness UGN with Z75 At front of vehicle, middle, approximately 18.5cm — —
(7.25 inches) forward of the harness break-out for
the right outer front object sensor.
J105 Front Bumper Harness UD5 At front of vehicle, middle, approximately 8cm — —
(3.5 inches) forward of the harness break-out for
the right outer front object sensor.
J106 Front Bumper Harness UGN with Z75 At front of vehicle, middle, approximately 14cm Forward Lamp Harness Routing - Left —
(5.5 inches) forward of the harness break-out for Engine Compartment
the front view camera.
J107 Front Bumper Harness UD5 At front of vehicle, middle, approximately 12cm — —
(4.75 inches) forward of the harness break-out for
the right outer front object sensor.
J110 Left Headlamp Harness — At front of vehicle, left, within the headlamp — —
assembly - left
J111 Forward Lamp Harness UGN with Z75 In the engine compartment, front middle, — —
approximately 4.5cm (1.75 inches) from break-
out to inline X100
J114 Forward Lamp Harness — In the engine compartment, left front, bottom, — —
approximately 9cm (3.5 inches) from break-out to
G101
J115 Forward Lamp Harness — In the engine compartment, left front, in the Forward Lamp Harness Routing - Left —
breakout to X110 approximately 18cm (7 inches) Engine Compartment
from the main harness bundle
J116 Forward Lamp Harness Z75 In the engine compartment, left front, Left Rear Door Harness Routing —
approximately 20cm (7.75 inches) from break-out
to X110
J117 Forward Lamp Harness Z75 In the engine compartment, left front, — —
approximately 15cm (5.75 inches) from break-out
to X110
J118 Left Multifunction Lamp Harness Z75 At front of vehicle, left, within the multifunction — —
lamp assembly in the front fascia - left
J120 Right Headlamp Harness — At front of vehicle, right, within the headlamp — —
assembly - right
J121 Auxiliary Battery Harness 5W4 or 9C1 In the engine compartment, left front — —
J123 Engine Harness L96 In the engine compartment, on top of engine Engine Harness Routing - Left Rear —
assembly, rear of center, approximately 5cm (2 (L96)
inches) from break-out to B37B Engine Oil
Pressure Sensor
J125 Forward Lamp Harness — In the engine compartment, front, right of middle, Forward Lamp Harness Routing - Right —
bottom, approximately 7.5cm (3 inches) from Engine Compartment
break-out to G102
J126 Engine Harness L83 or L86 In the engine compartment, front left of center, Engine Harness Routing - Left Front —
near thermostat housing, approximately 15.5cm (L83 or L86)
(6 inches) from break-out to X115,
J126 Engine Harness L96 In the engine compartment, front left of center, Engine Harness Routing - Left Front —
bottom left of the engine, in harness break-out to (L83 or L86)
M64 Starter Motor, approximately 12cm (4.75
inches) rearward of the B34 Engine Coolant
Temperature Sensor
J127 Engine Harness L83 or L86 In the engine compartment, front left of center, in —
harness break-out to ECM, approximately 17cm
• Engine Harness Routing - Left Front
(L83 or L86)
(6.5 inches) from main harness bundle
• Engine Harness Routing - Left Rear
(L96)
J127 Engine Harness L96 In the engine compartment, front left of center —
• Engine Harness Routing - Left Front
(L83 or L86)
J128 Right Multifunction Lamp Z75 At front of vehicle, right, within the multifunction — —
Harness lamp assembly in the front fascia - right
J130 Forward Lamp Harness — In the engine compartment, left front, bottom, Forward Lamp Harness Routing - Left —
approximately 5cm (2 inches) from break-out to Engine Compartment
the left impact sensor
J148 Engine Harness L96 In the engine compartment, middle left of center, — —
top and back of engine assembly , approximately
16cm (6.25 inches) from the main harness on the
breakout to B37B Engine Oil Pressure Sensor
J149 Engine Harness L96 In the engine compartment, middle left of center, — —
top of engine assembly , approximately 12.5cm
(5 inches) rearward of break-out to B74 Manifold
Absolute Pressure Sensor
J150 Engine Harness K59 In the engine compartment, front left of center, Engine Harness Routing - Left Front —
bottom near power steering pump, approximately (L83 or L86)
14cm (5.50 inches) from break-out to the left
knock sensor
J151 Engine Harness K59 In the engine compartment, front left of center, Engine Harness Routing - Left Front —
bottom near power steering pump, approximately (L83 or L86)
6cm (2.25 inches) from break-out to the left
knock sensor
J152 Engine Harness K59 In the engine compartment, middle left of center, Engine Harness Routing - Left Front —
near top, approximately 5cm (2 inches) forward of (L83 or L86)
break-out to ignition coil number 1
J153 Engine Harness K59 In the engine compartment, middle left of center, Engine Harness Routing - Left Front —
near top, approximately 3cm (1 inch) rearward of (L83 or L86)
break-out to ignition coil number 1
J161 Engine Harness L83 or L86 In the engine compartment, middle left of center, —
near top, approximately 7cm (2.75 inches)
• Engine Harness Routing - Right Rear
(L83 or L86)
rearward of break-out to ignition coil number 1
• Engine Harness Routing - Left Front
(L83 or L86)
J161 Ignition Coil (Odd) Harness L96 In the engine compartment, middle left of center, —
on top of the engine assembly, approximately
• Engine Harness Routing - Right Rear
(L83 or L86)
5cm (2 inches) from break-out to X170
• Engine Harness Routing - Left Front
(L83 or L86)
J162 Engine Harness L83 or L86 In the engine compartment, middle right of — —
center, near top, approximately 5cm (2 inches)
foreward of break-out to ignition coil number 4
J162 Ignition Coil (Even) Harness L96 In the engine compartment, middle left of center, — —
on top of the engine assembly, approximately
5cm (2 inches) from break-out to X171
J163 Engine Harness L83 or L86 In the engine compartment, front left of center, Engine Harness Routing - Left Front —
near top, approximately 10.5cm (4 inches) from (L83 or L86)
break-out to engine oil pressure sensor
J164 Ignition Coil (Even) Harness L96 In the engine compartment, middle left of center, — —
on top of the engine assembly, approximately
5cm (2 inches) from break-out to X171
J165 Engine Harness L83 or L86 In the engine compartment, rear left of center, on —
break-out to X115, approximately 12cm (4.75
• Engine Harness Routing - Left Rear
(L96)
inches) from main harness bundle
• Engine Harness Routing - Left Front
(L83 or L86)
J165 Engine Harness L96 In the engine compartment, rear left of center, —
left side of engine, approximately 7cm (2.75
• Engine Harness Routing - Left Rear
(L96)
inches) from break-out to X115
• Engine Harness Routing - Left Front
(L83 or L86)
J166 Engine Harness L83 or L86 In the engine compartment, rear center, top, — —
approximately 19cm (7.5 inches) left of break-out
to G140
J166 Ignition Coil (Odd) Harness L96 In the engine compartment, middle left of center, — —
on top of the engine assembly, approximately
5cm (2 inches) from break-out to X170
J167 Ignition Coil (Even) Harness L96 In the engine compartment, middle left of center, — —
on top of the engine assembly, approximately
5cm (2 inches) from break-out to X171
J178 Engine Harness M5U In the engine compartment, rear center, top, — —
approximately 18cm (7 inches) from break-out to
X160
J191 Chassis Harness — Underside of the vehicle, left frame rail, Chassis Harness Routing —
approximately 35.5cm (14 inches) rearward of
break-out for G121
J192 Chassis Harness BRS Underside of the vehicle, left frame rail, Chassis Harness Routing —
approximately 30.5cm (12 inches) rearward of
break-out for G121
J200 Instrument Panel Harness — In the instrument panel, left of center, behind Instrument Panel Harness Routing - —
cluster, approximately 2cm (1 inches) from Rear of Instrument Panel
break-out to G218
J201 Instrument Panel Harness — In the instrument panel, left of center, behind Instrument Panel Harness Routing - —
cluster, approximately 2cm (1 inches) from Rear of Instrument Panel
break-out to G218
J205 Instrument Panel Harness — In the instrument panel, left of center, behind Instrument Panel Harness Routing - —
cluster, approximately 4cm (1.5 inches) from Rear of Instrument Panel
break-out to G218
J207 Brake/Clutch Harness NP0 or NQH Underside of instrument panel, left side, — —
approximately 44cm (17.25 inches) from break-
out to transfer case control module
J208 Instrument Panel Harness — In the instrument panel, left side, on a break-out —
to the BCM, approximately 14cm (5.5 inches)
• Instrument Panel Harness Routing -
Rear of Instrument Panel
from main harness bundle
• Instrument Panel Harness Routing -
Rear of Instrument Panel
J210 Instrument Panel Harness — In the instrument panel, left side, approximately Instrument Panel Harness Routing - —
2.5cm (1 inch) from breakout to BCM Rear of Instrument Panel
J211 Instrument Panel Harness — In the instrument panel, left of center, behind Instrument Panel Harness Routing - —
cluster, approximately 7cm (2.75 inches) from Rear of Instrument Panel
break-out to G218
J212 Instrument Panel Harness Z75 In the instrument panel, left of center, behind Instrument Panel Harness Routing - —
cluster, approximately 12cm (4.75 inches) from Rear of Instrument Panel
breakout to X300
J215 Instrument Panel Harness X88 or Z88 In the instrument panel, center, approximately — —
7cm (2.8 inches) from break-out to the info
display module
J220 Instrument Panel Harness — In the instrument panel, center, approximately Instrument Panel Harness Routing - —
5cm (2 inches) from break-out to the media disc Rear of Instrument Panel
player
J241 Instrument Panel Harness — In the instrument panel, left side, on a break-out — —
to X225, in a formed conduit, approximately
20cm (8 inches) from X225
J242 Instrument Panel Harness — In the instrument panel, right side, behind glove Instrument Panel Harness Routing - —
box, approximately 5cm (2 inches) from break- Rear of Instrument Panel
out to the right instrument panel fuse block
J250 Instrument Panel Harness IO5 or IO6 or TG5 In the instrument panel, center, approximately Instrument Panel Harness Routing - —
20cm (7.75 inches) from break-out to the right Rear of Instrument Panel
instrument panel fuse block
J251 Instrument Panel Harness — In the instrument panel, center, approximately Instrument Panel Harness Routing - —
6cm (2.5 inches) from break-out to the radio Rear of Instrument Panel
J255 HVAC Harness — In the front of the passenger compartment, near HVAC Assembly Harness Routing —
center, approximately 4cm (1.5 inches) from
breakout to G210
J257 HVAC Harness — In the front of the passenger compartment, near HVAC Assembly Harness Routing —
center, approximately 23.5cm (9.25 inches) from
breakout to X215
J258 HVAC Harness — In the front of the passenger compartment, near HVAC Assembly Harness Routing —
center, approximately 6.5cm (2.5 inches) from
breakout to air temerature door actuator - right
J260 Instrument Panel Harness IO5 or IO6 with UE1, UEU, In the instrument panel, center, approximately Instrument Panel Harness Routing - —
UFL, or UHX 13cm (5 inches) from break-out to the radio Rear of Instrument Panel
J279 Steering Column Harness — In the front of the passenger compartment, left of — —
center, along steering column
J284 Steering Column Harness — In the front of the passenger compartment, left of — —
center, along steering column
J285 Steering Column Harness — In the front of the passenger compartment, left of Steering Wheel Harness Routing —
center, in steering wheel, between S70L and
break-out to X85
J286 Steering Column Harness UVD In the front of the passenger compartment, left of — —
center, in steering wheel, between S70R and
break-out to X85
J289 Body Harness — In the passenger compartment, front, left of Body Harness Routing - Left Front of —
center, behind instrument panel, inside a formed Passenger Compartment
conduit, approximately 6cm (2.25 inches) from
the break-out to the instrument panel junction
block
J294 Instrument Panel Harness — In the instrument panel, left side, between break- Instrument Panel Harness Routing - —
out for the BCM and break-out for X399 Rear of Instrument Panel
J295 Steering Column Harness — In the front of the passenger compartment, left of Steering Wheel Harness Routing —
center, in steering wheel, between S70R and
break-out to X85
J301 Overhead Console Harness — In the passenger compartment, overhead, front Overhead Console Harness Routing —
and center, on break-out to right overhead
console reading lamp, approximately 3cm (1.25
inches) from main harness bundle
J302 Overhead Console Harness — In the passenger compartment, overhead, front Overhead Console Harness Routing —
and center, approximately 3.5cm (1.25 inches)
from break-out to floor console flood lamp
J304 Body Harness Z75 In the passenger compartment, front, left side, Body Harness Routing - Left Front of —
behind instrument panel, approximately 4cm (1.5 Passenger Compartment
inches) from the break-out to X225
J306 Body Harness — In the passenger compartment, forward of Body Harness Routing - Left Front of —
middle, just left of center, between driver and Passenger Compartment
passenger seat, in a formed conduit,
approximately 27.5cm (10.75 inches) from the
break-out to the inflatable restraint sensing and
diagnostic module
J307 Body Harness DL3 or DR4 In the passenger compartment, front, left side, Body Harness Routing - Left Front of —
along A-pillar, in the break-out to X500, in a Passenger Compartment
formed conduit, approximately 20cm (7.75
inches) from the main harness bundle
J308 Body Harness — In the passenger compartment, front, left side, Body Harness Routing - Left Front of —
along A-pillar, in the break-out to the left Passenger Compartment
instrument panel fuse block, approximately 4cm
(1.5 inches) from the main harness bundle
J309 Body Harness JL1, NP0 or NQH In the passenger compartment, front, left side, Body Harness Routing - Left Front of —
behind instrument panel, approximately 6cm Passenger Compartment
(2.25 inches) from the break-out for the Park
Brake Switch
J310 Body Harness UTT In the passenger compartment, front, left side, Body Harness Routing - Left Front of —
along A-pillar, forward of driver door sill, Passenger Compartment
approximately 5cm (2 inches) from the break-out
to left instrument panel fuse block
J311 Headliner Harness — In the passenger compartment, overhead, front Headliner Harness Routing —
and to the left, approximately 14cm (5.5 inches)
fromt the break-out to X316
J312 Headliner Harness — In the passenger compartment, overhead, front Headliner Harness Routing —
and to the left, approximately 45cm (17.75
inches) fromt the break-out to X316
J314 Driver Seat Harness — In the passenger compartment, forward of Driver Seat Harness Routing —
middle, left of center, within the driver seat
cusion, between the break-out to sear front
vertical motor and break-out to seat belt switch
J315 Driver Seat Harness — In the passenger compartment, forward of Driver Seat Harness Routing —
middle, left of center, within the driver seat
cusion, between the break-out to sear front
vertical motor and break-out to seat rear vertical
motor
J317 Driver Seat Harness KB6 In the passenger compartment, forward of Driver Seat Harness Routing —
middle, left of center, within the driver seat
cusion, between X310 and break-out to seat rear
vertical motor
J319 Headliner Harness DNU or U42 In the passenger compartment, overhead, front Headliner Harness Routing —
and to the left, approximately 56cm (22 inches)
fromt the break-out to X203
J320 Headliner Harness AZ3 In the passenger compartment, overhead, front Headliner Harness Routing —
and to the left, approximately 38cm (15 inches)
fromt the break-out to X316
J322 Body Harness without SWB or Z75 In the passenger compartment, forward of Body Harness Routing - Right Front of —
middle, just right of center, between driver and Passenger Compartment
passenger seat, in a formed conduit,
approximately 20.5cm (8 inches) from the break-
out to G327
J323 Passenger Seat Harness AN3, A95, KA1 or KB6 In the passenger compartment, forward of — —
middle, right of center, within the passenger seat
cusion, between break-out for passenger seat
back connector and break-out for passenger
presence module
J330 Body Harness BTM or UGN In the passenger compartment, forward of Body Harness Routing - Left Front of —
middle, left side, under the driver seat, near the Passenger Compartment
driver door sill, in a formed conduit,
approximately 9cm (3.5 inches) from the break-
out for G325
J332 Headliner Harness — In the passenger compartment, overhead, front Headliner Harness Routing —
and to the left, approximately 51.5cm (20.25
inches) fromt the break-out to X316
J333 Overhead Console Harness — In the passenger compartment, overhead, front Overhead Console Harness Routing —
and center, on break-out to passenger disabled
indicator, approximately 5cm (2 inches) from
main harness bundle
J334 Body Harness UGN with Z75 In the passenger compartment, forward of Body Harness Routing - Left Front of —
middle, left side, under the driver seat, in a Passenger Compartment
formed conduit, approximately 14cm (5.5 inches)
from the break-out for G325
J339 Floor Console Harness D07 with DCK or K4C In passenger compartment, forward of middle, —
between the driver and passenger seat, in floor
• Floor Console Harness Routing - Top
(X88 or Z88)
console, approximately 17cm (6.75 inches) from
the break-out to the accessory power receptacle • Floor Console Harness Routing -
for the floor console storage bin Bottom Front (Z75)
J340 Body Harness UVH In the passenger compartment, near middle, left — —
side, at the base of the B-pillar, in a formed
conduit, approximately 7cm (2.75 inches) from
the break-out to X700
J350 Body Harness — In the passenger compartment, forward of Body Harness Routing - Left Front of —
middle, just right of center, between driver and Passenger Compartment
passenger seat, in a formed conduit,
approximately 35cm (13.75 inches) from the
break-out to G327
J352 Body Harness ATN or ATT In the passenger compartment, near middle, left Body Harness Routing - Left Middle of —
side, along left rear door sill, in a formed conduit, Passenger Compartment
approximately 15cm (6 inches) from the break-
out to X308
J353 Body Harness — In the passenger compartment, near middle, left Body Harness Routing - Left Front of —
side, at the base of the B-pillar, in a formed Passenger Compartment
conduit, approximately 7cm (2.75 inches) from
the break-out to X700
J354 Body Harness — In the passenger compartment, near rear, left Body Harness Routing - Left Middle of —
side, at base of C-pillar, approximately 25cm (10 Passenger Compartment
inches) from the break-out to the left rear side
impact sensor
J355 Chassis Harness — Underside of the vehicle, left frame rail, on main Chassis Harness Routing —
harness bundle, approximately 45cm (17.75
inches) rearward of break-out for the brake
control module
J356 Chassis Harness — Underside of the vehicle, left frame rail, on main Chassis Harness Routing —
harness bundle, approximately 15cm (6 inches)
rearward of break-out for the brake control
module
J357 Second Row Seat Left Harness ATN or ATT with KA6 In the passenger compartment, near middle, left Second Row Seat Harness Routing —
side, in the second row left seat, approximately
20.5cm (8 inches) from X308
J358 Body Harness 5W4 or 9C1 In the passenger compartment, near middle, left — —
side, near B-pillar, approximately 8.5cm (3.5
inches) from the break-out to G325
J360 Body Harness — In the passenger compartment, forward of Body Harness Routing - Right Front of —
middle, right side, along passenger door sill, in a Passenger Compartment
formed conduit, approximately 35.5cm (14
inches) from the break-out to G312
J361 Body Harness — In the passenger compartment, forward of Body Harness Routing - Left Front of —
middle, left of center, between driver and Passenger Compartment
passenger seat, in a formed conduit,
approximately 18cm (7 inches) from the break-
out to the inflatable restraint and diagnostic
module
J362 Body Harness AZ3, AX7, ATN, ATT, KA6 In the passenger compartment, forward of Body Harness Routing - Right Front of —
or Z75 middle, right side, along the driver door sill, just Passenger Compartment
forward of the B-pillar, in a formed conduit,
approximately 12cm (4.5 inches) from the break-
out to G312
J363 Body Harness — In the passenger compartment, forward of Body Harness Routing - Right Front of —
middle, right side, along the driver door sill, in a Passenger Compartment
formed conduit, approximately 44cm (17 inches)
from the break-out to G312
J364 Body Harness Z75 In the passenger compartment, forward of Body Harness Routing - Right Front of —
middle, right side, under the passenger seat, in a Passenger Compartment
formed conduit, approximately 7cm (2.75 inches)
from the break-out to G327
J366 Second Row Seat Right Harness ATN or ATT with KA6 In the passenger compartment, near middle, left Second Row Seat Harness Routing —
side, in the second row right seat, approximately
23cm (9 inches) from X378
J367 Body Harness DL3 or DR4 In the passenger compartment, front, right side, Body Harness Routing - Right Front of —
along passenger door sill, in a formed conduit, Passenger Compartment
approximately 41.5cm (16.5 inches) from the
break-out to X275
J368 Body Harness — In the passenger compartment, front, right side, Body Harness Routing - Right Front of —
along passenger door sill, in a formed conduit, Passenger Compartment
approximately 52.5cm (20.75 inches) from the
break-out to X275
J369 Body Harness — In the passenger compartment, front, right side, Body Harness Routing - Right Front of —
along passenger door sill, in a formed conduit, Passenger Compartment
approximately 57.5cm (22.5 inches) from the
break-out to X275
J370 Body Harness KA1, KA6 or UTT In the passenger compartment, front, right side, Body Harness Routing - Right Front of —
along passenger door sill, in a formed conduit, Passenger Compartment
approximately 30cm (11.75 inches) from the
break-out to G312
J371 Body Harness — In the passenger compartment, forward of Body Harness Routing - Right Front of —
middle, right side, under the passenger seat, in a Passenger Compartment
formed conduit, approximately 16cm (6.5 inches)
from the break-out to G312
J372 Body Harness A45 In the passenger compartment, forward of Body Harness Routing - Right Front of —
middle, right side, under the passenger seat, in a Passenger Compartment
formed conduit, approximately 12cm (4.75
inches) from the break-out to G312
J373 Body Harness UTT In the passenger compartment, forward of Body Harness Routing - Right Front of —
middle, right side, under the passenger seat, in a Passenger Compartment
formed conduit, approximately 3cm (1.25 inches)
from the break-out to G312
J375 Chassis Harness — Underside of the vehicle, left frame rail, on main Chassis Harness Routing —
harness bundle, approximately 8cm (3 inches)
forward of break-out for X351
J379 Body Harness DL3, DL8 or DR4 In the passenger compartment, forward of Body Harness Routing - Left Front of —
middle, just left of center, between the driver and Passenger Compartment
passenger seat, in a formed conduit,
approximately 43cm (17 inches) from the break-
out to the inflatable restraint and diagnostic
module
J382 Body Harness BRS, DL3, DR4 or HD7 In the passenger compartment, forward of Body Harness Routing - Left Front of —
middle, just left of center, between the driver and Passenger Compartment
passenger seat, in a formed conduit,
approximately 23.5cm (9.25 inches) from the
break-out to the inflatable restraint and diagnostic
module
J383 Body Harness — In the passenger compartment, forward of Body Harness Routing - Left Front of —
middle, just left of center, between the driver and Passenger Compartment
passenger seat, in a formed conduit,
approximately 32cm (12 inches) from the break-
out to the inflatable restraint and diagnostic
module
J384 Body Harness — In the passenger compartment, forward of Body Harness Routing - Left Front of —
middle, just right of center, between the driver Passenger Compartment
and passenger seat, in a formed conduit,
approximately 54cm (21 inches) from the break-
out to the inflatable restraint and diagnostic
module
J385 Body Harness ULT In the passenger compartment, forward of Body Harness Routing - Left Front of —
middle, center, between the driver and passenger Passenger Compartment
seat, in a formed conduit, approximately 11cm
(4.5 inches) from the break-out to the multi-axis
acceleration sensor
J386 Body Harness — In the passenger compartment, forward of Body Harness Routing - Left Front of —
middle, just left of center, between the driver and Passenger Compartment
passenger seat, in a formed conduit,
approximately 32.5cm (12.75 inches) from the
break-out to the inflatable restraint and diagnostic
module
J387 Accessory Power Harness AYE In the passenger compartment, in the floor — —
console, left side under the instrument panel,
approximately 11cm (4.5 inches) from KR103
DVD Relay
J401 Body Harness ATN or ATT In the rear compartment, rear, right side, along Body Harness Routing - Right Rear of —
the D-pillar, approximately 6cm (2.5 inches) from Passenger Compartment
the break-out to the right rear accessory power
receptacle
J402 Body Harness — In the rear compartment, rear, right side, just Body Harness Routing - Right Rear of —
forward of the D-pillar, approximately 16cm (6.5 Passenger Compartment
inches) from the break-out to the right glass
breakage sensor
J403 Body Harness K59, TC2, UEU, UFL UHX, In the rear compartment, rear, right side, along Body Harness Routing - Right Rear of —
UGN or UKC the D-pillar, approximately 8cm (3 inches) from Passenger Compartment
the break-out to the right rear accessory power
receptacle
J404 Body Harness ATT or ATN In the rear compartment, rear, right side, along Body Harness Routing - Right Rear of —
the D-pillar, on the break-out to X495, Passenger Compartment
approximately 6cm (2.5 inches) from the main
harness bundle
J410 Left Tail Lamp Harness Z75 At rear of vehicle, left, within the tail lamp — —
assembly - left
J449 Chassis Harness JL1 or Z85 Underside of the vehicle, left frame rail, at rear of Chassis Harness Routing —
vehicle, approximately 20cm (7.75 inches)
forward of break-out for the left rear speed sensor
J450 Chassis Harness — Underside of the vehicle, left frame rail, at rear of — —
vehicle, approximately 17cm (6.75 inches)
rearward of break-out for the fuel pump driver
control module
J451 Chassis Harness BRS, JL1, Z85 or Z95 Underside of the vehicle, left frame rail, at rear of Chassis Harness Routing —
vehicle, approximately 14cm (5.50 inches)
forward of break-out for the left rear speed sensor
J453 Chassis Harness — Underside of the vehicle, left frame rail, at rear of Chassis Harness Routing —
vehicle, approximately 7cm (3 inches) rearward
of break-out for the fuel pump driver control
module
J460 Body Harness ATN or ATT In the rear compartment, rear, left side, below Body Harness Routing - Left Rear of —
rear quarter glass, approximately 42cm (16.75 Passenger Compartment
inches) from the break-out to the glass breakage
sensor
J461 Body Harness UQS In the rear compartment, rear, left side, below Body Harness Routing - Left Rear of —
rear quarter glass, approximately 15cm (6 inches) Passenger Compartment
from the break-out to the glass breakage sensor
J462 Body Harness UQS In the rear compartment, rear, left side, below Body Harness Routing - Left Rear of —
rear quarter glass, approximately 6cm (2.25 Passenger Compartment
inches) from the break-out to the glass breakage
sensor
J490 Rear Bumper Harness UD5 or UD7 At rear of vehicle, right side, approximately —
3.5cm (1.5 inches) from the break-out to the right
• Rear Bumper Harness Routing (X88
or Z88)
side object sensor module
• Rear Bumper Harness Routing (Z75)
J492 Rear Bumper Harness UKC or TC2 At rear of vehicle, right side, approximately 12cm — —
(5 inches) from the break-out to the left middle
rear object sensor
J493 Rear Bumper Harness T79 At rear of vehicle, right side, approximately —
26.5cm (10.25 inches) from the break-out to the
• Rear Bumper Harness Routing (X88
or Z88)
right middle rear object sensor
• Rear Bumper Harness Routing (Z75)
J494 Rear Bumper Harness Z75 with UGN At rear of vehicle, right side, approximately Rear Bumper Harness Routing (Z75) —
4.5cm (2 inches) from the break-out to the right
outer rear object sensor
J495 Rear Bumper Harness UD5 or UD7 At rear of vehicle, right side, approximately —
6.5cm (2.5 inches) from the break-out to the right
• Rear Bumper Harness Routing (X88
or Z88)
outer rear object sensor
• Rear Bumper Harness Routing (Z75)
J499 Rear Bumper Harness T79, UKC or UGN with Z75 At rear of vehicle, right side, approximately 15cm —
(6 inches) from the break-out to the right outer
• Rear Bumper Harness Routing (Z75)
rear object sensor • Rear Bumper Harness Routing (X88
or Z88)
J511 Driver Door Harness HD7 In the driver door, near front, approximately — —
12.5cm (5 inches) from the break-out to X505
J515 Driver Door Harness — In the driver door, near front, approximately 5cm Driver Door Harness Routing —
(2 inches) from the break-out to X505
J516 Driver Door Trim Harness — In the driver door, near front, approximately 6cm Driver Door Harness Routing —
(2.5 inches) from the break-out to the outside
rearview mirror switch
J517 Left Outside Rearview Mirror DL3, DR4 or UKC On outside of driver door, front middle, forward of — —
Harness window opening
J519 Driver Door Trim Harness — In the driver door, near middle, approximately Driver Door Harness Routing —
1.5cm (0.5 inches) from the break-out to the
outside rearview mirror switch
J520 Driver Door Trim Harness Z75 In the driver door, near middle, approximately Driver Door Harness Routing —
7cm (3 inches) from the break-out to the driver
door accent lamp
J550 Driver Door Harness — In the driver door, near front, approximately 17cm — —
(6.75 inches) from the break-out to the driver
window motor
J611 Passenger Door Harness HD7 In the passenger door, near front, approximately Passenger Door Harness Routing —
12cm (5 inches) from the break-out to X605
J615 Passenger Door Harness — In the passenger door, near front, approximately Passenger Door Harness Routing —
5cm (2 inches) from the break-out to X605
J616 Passenger Door Trim Harness — In the passenger door, near front, approximately Passenger Door Harness Routing —
16.5cm (6.5 inches) from the break-out to the
passenger window switch
J617 Right Outside Rearview Mirror DL3, DR4 or UKC On outside of passenger door, front middle, — —
Harness forward of window opening
J620 Passenger Door Trim Harness Z75 In the passenger door, near front, approximately Passenger Door Harness Routing —
12cm (4.5 inches) from the break-out to the
passenger window switch
J710 Left Rear Door Harness UQH In the left rear door, near front, approximately Left Rear Door Harness Routing —
10cm (4 inches) from the break-out to the left
rear window switch
J711 Left Rear Door Harness UQH In the left rear door, near front, approximately Left Rear Door Harness Routing —
18cm (7.25 inches) from the break-out to the left
rear door speaker
J715 Left Rear Door Harness — In the left rear door, near front, approximately Left Rear Door Harness Routing —
3.5cm (1.25 inches) from the break-out to the left
rear window switch
J720 Left Rear Door Trim Harness Z75 In the left rear door, near middle, approximately Left Rear Door Harness Routing —
7cm (2.75 inches) from the break-out to the left
rear door pocket flood lamp
J810 Right Rear Door Harness UQH In the right rear door, near front, approximately Right Rear Door Harness Routing —
10cm (4 inches) from the break-out to the right
rear window switch
J811 Right Rear Door Harness UQH In the right rear door, near front, approximately Right Rear Door Harness Routing —
18cm (7.25 inches) from the break-out to the right
rear door speaker
J815 Right Rear Door Harness — In the right rear door, near front, approximately Right Rear Door Harness Routing —
3.5cm (1.25 inches) from the break-out to the
right rear window switch
J816 Right Rear Door Trim Harness Z75 In the right rear door, near middle, approximately Right Rear Door Harness Routing —
3cm (1.25 inches) from the break-out to the right
rear door pocket flood lamp
J820 Right Rear Door Trim Harness Z75 In the right rear door, near middle, approximately Right Rear Door Harness Routing —
7cm (2.75 inches) from the break-out to the right
rear door pocket flood lamp
J901 Liftgate Harness — In the liftgate, top, right side, in the harness Liftgate Harness Routing —
break-out to the defogger grid, approximately
34cm (13.25 Inches) from the defogger grid
connector
J902 Liftgate Harness — In the liftgate, top, left side, approximately 5cm Liftgate Harness Routing —
(2 Inches) from the break-out to the defogger grid
connector
J903 Liftgate Harness TB5 or TC2 In the liftgate, near center, just left of center, Liftgate Harness Routing —
approximately 10cm (4 Inches) from the break-
out to the liftgate latch assembly
J904 Liftgate Harness — In the liftgate, near center of tailgate, Liftgate Harness Routing —
approximately 10cm (4 Inches) from the break-
out to the right license plate lamp
JX200 Splice Pack – Instrument Panel — In the passenger compartment, at the rear of the Instrument Panel Harness Routing - —
instrument panel, left side at the Body Control Rear of Instrument Panel
Module
JX300 Splice Pack – Body UD5 In the passenger compartment, right side, in Body Harness Routing - Right Front of —
passenger footwell, behind kick panel trim near Passenger Compartment
X275
Items
Items
Items
1. P12 Horn
Items
2 4
1 5
19
6
18 7
17 8
9
16 15 14 13 12 11 10
Items
1 3
12
11
10 9 8 7
Items
1 3
12 4
11 5
10 6
9 7
8
Items
Items
Items
Items
Items
Items
5. P12 Horn
Items
2. C1 Battery
Items
Items
1. G13 Generator
9. G1 A/C Compressor
Items
6
2 3 4 5
10
11
18
12
17 16 15 14 13
Items
Items
Items
5
6
8
14
13
12 9
11
10
Items
1. G13 Generator
4
5 6
3
2
1
9
15 10
13
11
14
12
Items
Items
Items
Items
Items
1
2
Items
Items
Items
Items
Items
3. S31D Seat Heating and Cooling Switch - Driver (KA1 or KB6, without Z75)
4. S31P Seat Heating and Cooling Switch - Passenger (KA1 or KB6, without Z75)
Items
Items
Items
Items
Items
Items
Items
7. A11 Radio
Items
9. A11 Radio
Items
1. S70F Steering Wheel Controls Switch - Radio Volume (X88 or Z88 with UK3)
2. S70E Steering Wheel Controls Switch - Radio Presets (X88 or Z88 with UK3)
Items
Items
Items
Items
Items
4. M8 Blower Motor
Items
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
A
K 1
L
Items
Items
Items
5. B77RF Radio Volume Compensator Interior Noise Microphone - Right Front (NKC)
10. B77RF Radio Volume Compensator Interior Noise Microphone - Right Front (NKC)
12. B77LF Radio Volume Compensator Interior Noise Microphone - Left Front (NKC)
Items
Items
Items
5. M52P Seat Lumbar Support Horizontal Motor - Passenger (without Y91 or Z75)
6. A14P Seat Lumbar Support Pump - Passenger (Y91 or Z75 without ULT)
Items
Items
Items
3. A14D Seat Lumbar Support Pump - Driver (A45, with Y91 or Z75 without ULT)
4. M52D Seat Lumbar Support Horizontal Motor - Driver (without Y91 or Z75)
Items
5. P45LR Seat Haptic Movement Motor - Driver Left Rear (UEU, UFL UHX, or UGN)
8. P45RR Seat Haptic Movement Motor - Driver Right Rear (UEU, UFL UHX, or UGN)
Items
5. P45LR Seat Haptic Movement Motor - Driver Left Rear (UEU, UFL UHX, or UGN)
8. P45RR Seat Haptic Movement Motor - Driver Right Rear (UEU, UFL UHX, or UGN)
Items
Items
2. B124LR Folding Seat Back Position Switch - 2nd Row Left (ATN or ATT)
Items
1. B124RR Folding Seat Back Position Switch - 2nd Row Right (ATN or ATT)
Items
Items
Items
1. M109LR Folding Seat Back Unlatch Motor - 3rd Row Left (AS8)
2. M109RR Folding Seat Back Unlatch Motor - 3rd Row Right (AS8)
Items
Items
1 5 6
7
4 8
2
10
15
11
14
13
12
Items
Items
2 4
1 5
10 11 12
6
13
9
8
7
Items
Items
3
1
4
5 6
10
7
9
8
Items
Items
2 3
1
4
8 9
5
10
7 6
Items
Items
Items
1 4
14
5
13 6
12 11 10 9
Items
11. B306F Parking Assist Sensor - Rear Left Middle (UD5 or UD7)
12. B306E Parking Assist Sensor - Rear Left Outer (UD5 or UD7)
Items
1 2
3
4
5
Items
Items
1 2 3 4
11
10 7
9 8
Items
10. B306E Parking Assist Sensor - Rear Left Outer (UD5 or UD7)
3
4
5
6
1
7
11 8
10 9
Items
10. B306F Parking Assist Sensor - Rear Left Middle (UD5 or UD7)
11. B306E Parking Assist Sensor - Rear Left Outer (UD5 or UD7)
Items
9. E4RR Turn Signal Lamp - Right Rear (Z88, Z75, or X88 with T89)
11. E4LR Turn Signal Lamp - Left Rear (Z88, Z75, or X88 with T89)
12. E5AT Stop/Turn Signal Lamp - Left Lower (X88 without T89)
Items
5. E4RR Turn Signal Lamp - Right Rear (Z88, Z75, or X88 with T89)
8. E4LR Turn Signal Lamp - Left Rear (Z88, Z75, or X88 with T89)
Items
3. K174L Multifunction LED Control Module - Left Tail Lamp (Z75 or Z88)
7. E4RR Turn Signal Lamp - Right Rear (Z88, Z75, or X88 with T89)
8. K174L Multifunction LED Control Module - Left Tail Lamp (Z75 or Z88)
9. E4LR Turn Signal Lamp - Left Rear (Z88, Z75, or X88 with T89)
Items
8. R6A Terminating Resistor - High Speed Bus (without J71, JL1, Z85 or Z95)
Items
Items
1. G120 (L96)
2. G110
Items
1. G101
Items
1. G102
1 2
Items
1. G103
Items
1. G110
Items
1. G121
1 2
Items
Items
Items
1. G210
Items
1. G218
Items
1. G311
2. G325
Items
1. G327
2. G312
Items
1. G400
Items
1. G402
97 20 8
86 49 39
34
111 98 64 21 1 30A ELEC RNG BDS 42 15A PRK LP RT 91 15A THROT CONT
40
99 87 80 22 2 60A ABS PUMP 43 15A PRK LP LT 92 ECM RELAY
117 9
50 41
1 3 60A INT BEC LT1 44 30A UPFIT 3 93 15A HORN
100 88 35 23
67
4 40A MSB PASS 45 10A ALC RUN/CRANK 94 15A FOG LP
112 101 89 42 24 5 40A SUSP LEVELING CMPRSR 47 30A UPFIT 4 95 10A LT/RT HI BEAM
118 102 90 81 74 43
36
25 2
6 30 4WD TREC 48 UPFIT 4 RLY 100 15A O2 A SNSR
10
51 9 FUEL PUMP RLY 49 10A REV LP 101 30A ECM
103 91 82 75 68 10 40A ELEC PRK BRK 51 PRK LP RLY 102 15A ECM/TCM
65
83 76 37 12 11 13 60A INT BEC LT2 59 20A EURO TRLR 103 10A INT HTR AUX
14 60A REAR BEC1 60 10A A/C CONTRL 104 40A STRTR
58 32
104 17 40A MSB DRVR 63 30A UPFIT 1 107 10A AERO SHUTTER
119 64 SEC FUEL PUMP RLY 109 10A POLICE UPFIT
92 84 77 69
59 53 44 13 3 21 15A ALC EXH SOL
78 70 22 20A FUEL PUMP 67 30A TRLR BATT 112 STRTR RLY
45 26
105 60 54 23 10A ICCM 69 5A RC UPFIT 3 & 4 114 15A FRT WSW
46 27 24 30A RTD 70 5A VBAT UPFIT 3 & 4 115 15A RR WSW
55 47 28 14 4 25 30A FPPM 72 UPFIT 1 RLY 116 40A COOL FAN LT
71 61 26 AHA_RVC 74 15A ECM IGN 121 20A RT HID
106
85 28 30A UPFIT 2 75 10A MISC IGN SPARE 122 20A LT HID
62 16 15 29 UPFIT 2 RLY 76 15A TRANS IGN 123 40A COOL FAN RT
120 113 48 29 30 25A WPR 77 5A RC UPFIT 1 & 2
31 25A TIM 78 5A VBAT UPFIT 1 & 2
107 93 56 17 5 34 10A BCK UP LP 83 10A EURO TRLR RC
63
35 25A ABS VLV 84 RUN/CRNK RLY
121
122
114
115
108 94 72 30
36 30A TRLR BRK 87 15A ENG
95 31 37 UPFIT 3 RLY 88 20A INJ A ODD
123 116 109 32 18 6
39 10A TRLR STOP TRN RT 89 20A INJ B EVEN
57 40 10A TRKR STOP TRB LT 90 15A O2 B SNSR
66
79
X6
Fuses
7 — F7UA —
•
8 — F8UA —
•
11 — F11UA —
•
12 — F12UA —
•
15 — F15UA —
•
16 — F16UA —
•
18 — F18UA —
•
19 — F19UA —
•
20 — F20UA —
•
26 AHA_RVC F26UA 5A
•
27 - F27UA —
•
32 — F32UA —
•
33 — F33UA —
•
38 — F38UA —
•
46 — F46UA —
•
52 — F52UA —
•
53 — F53UA —
•
54 — F54UA —
•
56 — F56UA —
•
58 — F58UA —
•
61 — F61UA —
•
62 — F62UA —
•
2017 FULL SIZE SUV (C/K) ELECTRICAL SECTION
10/26/2016 - VERSION 1.0 566 / 1717
62 — F62UA —
•
65 — F65UA —
•
66 — F66UA —
•
73 — F73UA —
•
79 — F79UA —
•
81 — F81UA —
•
82 — F82UA —
•
86 — F86UA —
•
97 — F97UA —
•
98 — F98UA —
•
99 — F99UA —
•
105 — F105UA —
•
108 — F108UA —
•
110 — F110UA —
•
117 — F117UA —
•
50 — — —
• Not Used
71 — — —
• Not Used
80 — — —
• Not Used
TP1 — TP1 —
•
TP2 — TP2 —
•
X3
X1
X4
X2 X5
M8 L8 K6 J6 H6 G6 F3 E2 D3 C3
A3
N2
B2
A2
B1
N1
M1 L1 K1 J1 H1 G1 F1 E1 D1 C1 A1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
III 19301761 J-35616-35 (VT) J-38125-11A Not Available Not Available Not Available Not Available
IV 19301767 J-35616-2A (GY) J-38125-560 Not Available Not Available Not Available Not Available
A1 — — — Not Occupied — —
A3 - B1 — — — Not Occupied — —
C1 — — — Not Occupied — —
C3 — — — Not Occupied — —
E1 — — — Not Occupied — —
G2 - G3 — — — Not Occupied — —
G6 — — — Not Occupied — —
H5 — — — Not Occupied — —
K1 - M3 — — — Not Occupied — —
M6 - N2 — — — Not Occupied — —
K6 J6 H6 G6 F3 E2 D3 C3
L8
A3
M8 B2
A2
N2 B1
N1
M1 A1
C1
L1 K1 J1H1 G1 F1 E1 D1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
II 19301761 J-35616-35 (VT) J-38125-11A Not Available Not Available Not Available Not Available
III 19301761 J-35616-35 (VT) J-38125-36 Not Available Not Available Not Available Not Available
IV 19301767 J-35616-2A (GY) J-38125-560 Not Available Not Available Not Available Not Available
A3 - B2 — — — Not Occupied — —
C2 — — — Not Occupied — —
D1 - D2 — — — Not Occupied — —
F1 — — — Not Occupied — —
F3 - G2 — — — Not Occupied — —
H4 — — — Not Occupied — —
J1 — — — Not Occupied — —
K1 - K2 — — — Not Occupied — —
K6 - L6 — — — Not Occupied — —
L8 — — — Not Occupied — —
M2 - M4 — — — Not Occupied — —
M8 — — — Not Occupied — —
N2 — — — Not Occupied — —
M8 L8 K6 J6 H6 G6 F3 E2 D3 C3
A3
N2
B2
A2
B1
N1
M1 L1 K1 J1 H1 G1 F1 E1 D1 C1 A1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
III 19301761 J-35616-35 (VT) J-38125-11A Not Available Not Available Not Available Not Available
IV 19301761 J-35616-35 (VT) J-38125-36 Not Available Not Available Not Available Not Available
V 19301767 J-35616-2A (GY) J-38125-560 Not Available Not Available Not Available Not Available
A2 - A3 — — — Not Occupied — —
C2 - C3 — — — Not Occupied — —
D3 - E1 — — — Not Occupied — —
G2 - H1 — — — Not Occupied — —
H3 - H6 — — — Not Occupied — —
J2 - K2 — — — Not Occupied — —
K5 — — — Not Occupied — —
L7 — — — Not Occupied — —
M2 — — — Not Occupied — —
M6 — — — Not Occupied — —
N1 - N2 — — — Not Occupied — —
J6 H6 G6 F3 E2 D3 C3
K6
L8 A3
B2
M8
A2
N2
N1 B1
M1 L1 K1 J1 H1 G1 F1 E1 D1 C1 A1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
II 13575718 J-35616-44 (YE) J-38125-558 Not Available Not Available Not Available Not Available
III 19301761 J-35616-35 (VT) J-38125-11A Not Available Not Available Not Available Not Available
IV 19301761 J-35616-35 (VT) J-38125-36 Not Available Not Available Not Available Not Available
V 19301767 J-35616-2A (GY) J-38125-560 Not Available Not Available Not Available Not Available
A1 — — — Not Occupied — —
C2 - D3 — — — Not Occupied — —
E1 6 RD/WH 942 — II —
F1 - G1 — — — Not Occupied — —
G3 - G5 — — — Not Occupied — —
H1 - H4 — — — Not Occupied — —
J2 - J5 — — — Not Occupied — —
K3 - K4 — — — Not Occupied — —
K6 — — — Not Occupied — —
L7 - L8 — — — Not Occupied — —
M2 — — — Not Occupied — —
M4 — — — Not Occupied — —
M6 - N2 — — — Not Occupied — —
M8 L8 K6 J6 H6 G6 F3 E2 D3 C3
A3
N2
B2
A2
B1
N1
M1 L1 K1 J1 H1 G1 F1 E1 D1 C1 A1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13575718 J-35616-44 (YE) J-38125-558 Not Available Not Available Not Available Not Available
II 13575808 J-35616-2A (GY) J-38125-217 Not Available Not Available Not Available Not Available
III 13575832 J-35616-4A (PU) J-38125-11A Not Available Not Available Not Available Not Available
IV 19301761 J-35616-35 (VT) J-38125-11A Not Available Not Available Not Available Not Available
V 19301767 J-35616-2A (GY) J-38125-560 Not Available Not Available Not Available Not Available
B2 — — — Not Occupied — —
C3 - D1 — — — Not Occupied — —
E2 - F3 — — — Not Occupied — —
G5 — — — Not Occupied — —
H2 — — — Not Occupied — —
H4 - J1 — — — Not Occupied — —
J6 — — — Not Occupied — —
K3 — — — Not Occupied — —
L1 - L6 — — — Not Occupied — —
L8 - M4 — — — Not Occupied — —
M6 — — — Not Occupied — —
N1 — — — Not Occupied — —
X6
X5
4
X4
X3
2
X2
X1 1
X7 8
1 — F1UD 100A
•
3 — F3UD -
•
4 — F4UD 175A
•
5 — F7UD 60A
•
6 — F8UD 60A
•
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-45 (YE) No Tool Required Not Required Not Required Not Required Not Required
X2
X1
1 — F1UE 100A
•
•
2 — F2UE 50A
•
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required No Tool Required No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required No Tool Required No Tool Required Not Required Not Required Not Required Not Required
1
50
2 3
4
51
12
7 8 9 10 11 13
5 6
52 15 16 17 18 19 20 21
14
23 29
24 25 26 27 28
53 22
30
54 31 32 33 34 35 36 37 38 39
40
41 42
45 46 47 48 49
43 44
55
56
2 3
X3
4
12
7 8 9 10 11 13
5 6
15 16 21
17 18 19 20
14
25 26 27 28 29
23 24
+ + + + +
22
30
31 32 33 34 35 36 37 38 39
40
41 42
45 49
43 44 46 47 48
X1
Fuses
1 EMPTY F1DL —
•
2 EMPTY F2DL —
•
3 EMPTY F3DL —
•
9 EMPTY F9DL —
•
13 EMPTY F13DL —
•
14 EMPTY F14DL —
•
15 EMPTY F15DL —
•
21 EMPTY F21DL —
•
22 EMPTY F22DL —
•
23 EMPTY F23DL —
•
30 EMPTY F30DL —
•
31 EMPTY F31DL —
•
32 EMPTY F32DL —
•
35 EMPTY F35DL —
•
40 EMPTY F40DL —
•
41 EMPTY F41DL —
•
45 EMPTY F45DL —
•
48 EMPTY F48DL —
•
49 EMPTY F49DL —
•
50
X2
51
52
53
54
55
56
Fuses
56 EMPTY F56DL —
•
Relays
51 EMPTY — —
• Not Used
7 11 17 21 23 25 29 35 39
1
6
10 16 20 22 24 28 34 38 44
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
III 13578891 J-35616-2A (GY) J-38125-11A Not Available Not Available Not Available Not Available
IV 19301761 J-35616-35 (VT) J-38125-11A Not Available Not Available Not Available Not Available
V 19301761 J-35616-35 (VT) J-38125-36 Not Available Not Available Not Available Not Available
VI 19301767 J-35616-2A (GY) J-38125-560 Not Available Not Available Not Available Not Available
4 — — — Not Occupied — —
6 - 13 — — — Not Occupied — —
19 — — — Not Occupied — —
22 — — — Not Occupied — —
24 - 26 — — — Not Occupied — —
29 — — — Not Occupied — —
31 — — — Not Occupied — —
35 — — — Not Occupied — —
38 - 41 — — — Not Occupied — —
1 7 11 17 21 23 25 29 35 39
6 10 16 20 22 24 28 34 38 44
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
II 13580025 J-35616-35 (VT) J-38125-11A Not Available Not Available Not Available Not Available
III 19301761 J-35616-35 (VT) J-38125-11A Not Available Not Available Not Available Not Available
IV 19301761 J-35616-35 (VT) J-38125-36 Not Available Not Available Not Available Not Available
V 19301767 J-35616-2A (GY) J-38125-560 Not Available Not Available Not Available Not Available
6 — — — Not Occupied — —
11 - 13 — — — Not Occupied — —
16 - 17 — — — Not Occupied — —
19 — — — Not Occupied — —
21 - 24 — — — Not Occupied — —
29 - 33 — — — Not Occupied — —
39 - 42 — — — Not Occupied — —
10 1
20 11
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 19301761 J-35616-35 (VT) J-38125-11A Not Available Not Available Not Available Not Available
II 19301767 J-35616-2A (GY) J-38125-560 Not Available Not Available Not Available Not Available
1 - 10 — — — Not Occupied — —
15 - 20 — — — Not Occupied — —
1
50
2 3
4
51
12
7 8 9 10 11 13
5 6
52 15 16 17 18 19 20 21
14
23 29
24 25 26 27 28
53 22
30
54 31 32 33 34 35 36 37 38 39
40
41 42
45 46 47 48 49
43 44
55
56
X3
1
2 3
12
7 8 9 10 11 13
5 6
15 16 21
17 18 19 20
14
23 29
22 24 25 26 27 28
30
31 32 33 34 35 36 37 38 39
40
41 42
45 49
43 44 46 47 48
X1
Fuses
1 EMPTY F1DR —
•
2 EMPTY F2DR —
•
3 EMPTY F3DR —
•
5 EMPTY F5DR —
•
6 EMPTY F6DR —
•
7 EMPTY F7DR —
•
9 EMPTY F9DR —
•
10 EMPTY F10DR —
•
11 EMPTY F11DR —
•
14 EMPTY F14DR —
•
15 EMPTY F15DR —
•
16 EMPTY F16DR —
•
17 EMPTY F17DR —
•
18 EMPTY F18DR —
•
22 EMPTY F22DR —
•
23 EMPTY F23DR —
•
24 EMPTY F24DR —
•
25 EMPTY F25DR —
•
30 EMPTY F30DR —
•
31 EMPTY F31DR —
•
32 EMPTY F32DR —
•
33 EMPTY F33DR —
•
34 EMPTY F34DR —
•
35 EMPTY F35DR —
•
40 EMPTY F40DR —
•
41 EMPTY F41DR —
•
42 EMPTY F42DR —
•
43 EMPTY F43DR —
•
50
51
X2
52
53
54
55
56
Fuses
56 EMPTY F56DR —
•
Relays
51 EMPTY — —
• Not Used
7 11 17 21 23 25 29 35
1 39
6 44
10 16 20 22 24 28 34 38
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
II 13575718 J-35616-44 (YE) J-38125-558 Not Available Not Available Not Available Not Available
IV 19301751 J-35616-2A (GY) J-38125-560 Not Available Not Available Not Available Not Available
V 19301761 J-35616-35 (VT) J-38125-11A Not Available Not Available Not Available Not Available
VI 19301761 J-35616-35 (VT) J-38125-36 Not Available Not Available Not Available Not Available
VII 19301767 J-35616-2A (GY) J-38125-560 Not Available Not Available Not Available Not Available
5 — — — Not Occupied — —
7 - 14 — — — Not Occupied — —
17 — — — Not Occupied — —
23 — — — Not Occupied — —
25 - 26 — — — Not Occupied — —
28 — — — Not Occupied — —
31 — — — Not Occupied — —
32 0.5 GN/BN 6132 Local Interconnect Network Serial Data Bus 1 VII —
35 - 36 — — — Not Occupied — —
39 — — — Not Occupied — —
44 — — — Not Occupied — —
7 11 17 21 23 25 29 35 39
1
6
10 16 20 22 24 28 34 38 44
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
II 19301761 J-35616-35 (VT) J-38125-11A Not Available Not Available Not Available Not Available
III 19301761 J-35616-35 (VT) J-38125-36 Not Available Not Available Not Available Not Available
IV 19301767 J-35616-2A (GY) J-38125-560 Not Available Not Available Not Available Not Available
9 — — — Not Occupied — —
11 - 15 — — — Not Occupied — —
18 — — — Not Occupied — —
20 - 21 — — — Not Occupied — —
23 - 28 — — — Not Occupied — —
30 - 33 — — — Not Occupied — —
36 - 37 — — — Not Occupied — —
39 - 44 — — — Not Occupied — —
10 1
20 11
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
II 19301761 J-35616-35 (VT) J-38125-11A Not Available Not Available Not Available Not Available
III 19301767 J-35616-2A (GY) J-38125-560 Not Available Not Available Not Available Not Available
2 0.5 GN/BN 6132 Local Interconnect Network Serial Data Bus 1 III —
9 — — — Not Occupied — —
11 - 20 — — — Not Occupied — —
X1 X2
34
65
62 1 63
60
54 59
2 3 4 + 5
48 53
6 7 8 + 9
42 47
10 11 12 13
38 41
14 15 16 17
31
18 19 20 35
27 + 24
21 22 30
23
22 25 26
26
27
17 28 21
29
11 30 16
8
33
32
31
7
1
Fuses
2 - F2RA 15A
•
3 - F3RA 15A
•
4 - F4RA 15A
•
•
5 - F5RA 15A
•
6 - F6RA -
•
7 - F7RA 10A
•
8 - F8RA -
•
10 - F10RA -
•
11 - F11RA 10A
•
12 - F12RA -
•
13 - F13RA -
•
14 - F14RA 10A
•
15 - F15RA 20A
•
16 - F16RA -
•
17 - F17RA -
•
18 - F18RA 30A
•
19 - F19RA -
•
20 - F20RA -
•
21 - F21RA 20A
•
•
22 - F22RA 10A
•
23 - F23RA -
•
24 - F24RA 30A
•
•
25 - F25RA 30A
•
26 - F26RA -
•
28 - F28RA 30A
•
30 - F30RA 20A
•
•
65
64
62
63
61
60
55
59
57
56
54
58
51
53
52
50
49
48
45
43
42
47
46
44
41
40
39
38
37
36
35
31
34
33
32
29
28
27
30
22
24
23
26
25
17
21
20
19
18
11
15
16
13
12
14
8
10
9
7
1
2
3
5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Core Crimp Insulation Crimp
I Not Available Not Available Not Available Not Available Not Available Not Available Not Available
2 0.5 BN/VT 193 Rear Defog Relay Control I DL3, DL8 or DR4
4 - - - Not Occupied - -
25 0.5 BU/WH 6128 Rear Closure Unlatch Motor Unlatch Control I TB4
29 - - - Not Occupied - -
52 2.5 BN/VT 293 Rear Defog Element Supply Voltage IV UTT or UTV
57 2.5 BN/YE 2267 Mirror Heating Element Supply Voltage VI DL3, DL8 or DR4
59 - - - Not Occupied - -
0.5 BK 1150
62 4 BN/VT 938 IX -
64 6 RD/WH 942 X -
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required No Tool Required No Tool Required Not Required Not Required Not Required Not Required
X7 X6 X3
X4 X8
X9
X5
X2
X1
6 11 16 21 26 31 36 41
1 46
5 50
10 15 20 25 30 35 40 45
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 19301761 J-35616-35 (VT) J-38125-11A Not Available Not Available Not Available Not Available
II 19301761 J-35616-35 (VT) J-38125-36 Not Available Not Available Not Available Not Available
III 19301767 J-35616-2A (GY) J-38125-560 Not Available Not Available Not Available Not Available
1 — — — Not Occupied — —
3 - 10 — — — Not Occupied — —
12 - 15 — — — Not Occupied — —
17 — — — Not Occupied — —
19 0.5 D-BU/YE 6105 High Speed GMLAN Serial Data (+) 2 III —
23 0.35 BN/YE 780 Driver Door Lock Switch Lock Signal III —
24 0.5 BN 7634 Integrated Trailer Brake Controller Redundant Manual Apply Signal III —
26 0.5 D-BU/RD 7632 Integrated Trailer Brake Controller Switch 5V Reference III —
27 0.5 BK/BN 7631 Integrated Trailer Brake Controller Switch Low Reference III —
28 0.35 BN/WH 781 Driver Door Lock Switch Unlock Signal III —
29 0.5 YE 7635 Integrated Trailer Brake Controller Manual Apply Signal III —
37 — — — Not Occupied — —
41 0.5 GN/BK 7633 Integrated Trailer Brake Controller User Gain Signal III —
45 0.35 GN/BN 5852 Rear Park Assist LED Disable Signal III —
49 0.5 YE/WH 816 Brake Transmission Shift Interlock Solenoid Control III —
6 11 16 21 26 31 36 41
1 46
5 50
10 15 20 25 30 35 40 45
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
II 19301751 J-35616-2A (GY) J-38125-560 Not Available Not Available Not Available Not Available
III 19301761 J-35616-35 (VT) J-38125-11A Not Available Not Available Not Available Not Available
IV 19301761 J-35616-35 (VT) J-38125-36 Not Available Not Available Not Available Not Available
V 19301767 J-35616-2A (GY) J-38125-560 Not Available Not Available Not Available Not Available
13 - 14 — — — Not Occupied — —
17 — — — Not Occupied — —
18 4 BK 550 Ground I —
25 — — — Not Occupied — —
28 — — — Not Occupied — —
33 - 34 — — — Not Occupied — —
37 0.5 YE/WH 1695 Four Wheel Drive Wheel Lock Indicator Control V —
39 — — — Not Occupied — —
41 - 42 — — — Not Occupied — —
45 — — — Not Occupied — —
6 11 16 21 26 31 36 41
1 46
5 50
10 15 20 25 30 35 40 45
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13578891 J-35616-2A (GY) J-38125-11A Not Available Not Available Not Available Not Available
II 19301761 J-35616-35 (VT) J-38125-11A Not Available Not Available Not Available Not Available
III 19301761 J-35616-35 (VT) J-38125-36 Not Available Not Available Not Available Not Available
IV 19301767 J-35616-2A (GY) J-38125-560 Not Available Not Available Not Available Not Available
10 - 12 — — — Not Occupied — —
20 — — — Not Occupied — —
23 — — — Not Occupied — —
26 — — — Not Occupied — —
30 - 35 — — — Not Occupied — —
37 — — — Not Occupied — —
39 - 40 — — — Not Occupied — —
43 - 44 — — — Not Occupied — —
48 — — — Not Occupied — —
50 — — — Not Occupied — —
6 11 16 21 26 31 36 41
1 46
5 50
10 15 20 25 30 35 40 45
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 19301761 J-35616-35 (VT) J-38125-11A Not Available Not Available Not Available Not Available
II 19301761 J-35616-35 (VT) J-38125-36 Not Available Not Available Not Available Not Available
III 19301767 J-35616-2A (GY) J-38125-560 Not Available Not Available Not Available Not Available
1 — — — Not Occupied — —
11 0.35 GY/WH 3153 Lane Departure Warning Disable Switch Signal III —
12 - 13 — — — Not Occupied — —
15 0.35 GY/RD 6029 Four Wheel Drive Mode Switch 5V Reference III —
17 - 18 — — — Not Occupied — —
20 — — — Not Occupied — —
36 — — — Not Occupied — —
6 11 16 21 26 31 36 41
1 46
5 50
10 15 20 25 30 35 40 45
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 19301761 J-35616-35 (VT) J-38125-11A Not Available Not Available Not Available Not Available
II 19301767 J-35616-2A (GY) J-38125-560 Not Available Not Available Not Available Not Available
7 0.5 BN 7634 Integrated Trailer Brake Controller Redundant Manual Apply Signal II —
14 0.5 BK/BN 7631 Integrated Trailer Brake Controller Switch Low Reference II —
16 — — — Not Occupied — —
20 - 21 — — — Not Occupied — —
24 — — — Not Occupied — —
30 0.5 GN/BK 7633 Integrated Trailer Brake Controller User Gain Signal II —
31 — — — Not Occupied — —
33 — — — Not Occupied — —
35 - 36 — — — Not Occupied — —
40 - 44 — — — Not Occupied — —
46 - 50 — — — Not Occupied — —
C A
D B
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
10 1
20 11
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 19301761 J-35616-35 (VT) J-38125-11A Not Available Not Available Not Available Not Available
II 19301761 J-35616-35 (VT) J-38125-36 Not Available Not Available Not Available Not Available
III 19301767 J-35616-2A (GY) J-38125-560 Not Available Not Available Not Available Not Available
9 — — — Not Occupied — —
12 - 13 — — — Not Occupied — —
15 - 18 — — — Not Occupied — —
10 1
20 11
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
11 — — — Not Occupied — —
10 1
20 11
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
14 3 BK 550 Ground II —
19 0.5 YE/WH 1695 Four Wheel Drive Wheel Lock Indicator Control I —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
4 BK 2150 —
2.5 GY 120 —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
5 1
10 6
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
II Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
3 — — — — II DRZ
4 — — — — II DRZ
6 — — — — II DRZ
7 — — — — II DRZ
10 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
II Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
10
20 11
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I J-35616-64B (LT BU) J-38125-215A Not Available Not Available Not Available Not Available
III Pending J-35616-64B (LT BU) J-38125-215A Not Available Not Available Not Available Not Available
A11 Radio X1
0.35 GN 5841 II —
11 - 12 — — — Not Occupied — —
15 - 18 — — — Not Occupied — —
4 1
8 5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
A11 Radio X2
8 — — — Not Occupied — —
8 1
16 9
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available J-35616-2A (GY) J-38125-11A Not Available Not Available Not Available Not Available
A11 Radio X3
13 - 15 — — — Not Occupied — —
5 4
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Pending No Tool Required Not Required Not Required Not Required Not Required
3 0.75 YE/BU 767 Driver Power Seat Lumbar Motor Down Control I —
4 — — — Not Occupied — —
5 4
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
3 0.75 BU/YE 792 Passenger Power Seat Lumbar Motor Down Control I —
4 — — — Not Occupied — —
D A
H E
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
8 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
4 0.5 GY 3986 Cinch Latch Lift Gate Stall Motor Release Signal I —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
4 — — — Not Occupied — —
5 1
10 6
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
5 1
10 6
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
2 0.35 BN/WH 3269 Child Security Lock Motor Status Signal Left Rear I —
10 — — — Not Occupied — —
5 1
10 6
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
4 — — — Not Occupied — —
5 1
10 6
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
4 0.35 GY/BK 3268 Child Security Lock Motor Status Signal Right Rear I —
6 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-13 (BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-13 (BU) No Tool Required Not Required Not Required Not Required Not Required
2 — — — Not Occupied — —
3 0.5 GY/GN 5996 Driver Outside Rear View Mirror Puddle Lamp Control I —
4 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-13 (BU) No Tool Required Not Required Not Required Not Required Not Required
3 0.5 GY/GN 5996 Driver Outside Rear View Mirror Puddle Lamp Control I —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-13 (BU) No Tool Required Not Required Not Required Not Required Not Required
3 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-13 (BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-13 (BU) No Tool Required Not Required Not Required Not Required Not Required
2 — — — Not Occupied — —
3 0.5 GY/GN 5996 Driver Outside Rear View Mirror Puddle Lamp Control I —
4 — — — Not Occupied — —
10 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
II 19300631 J-35616-64B (LT BU) J-38125-215A Not Available Not Available Not Available Not Available
2 — — — Not Occupied — —
7 — — — Not Occupied — —
6 1
12 7
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
II 19300631 J-35616-64B (LT BU) J-38125-215A Not Available Not Available Not Available Not Available
9 — — — Not Occupied — —
12 — — — Not Occupied — —
6 1
12 7
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
5 - 12 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
2 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
2 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
2 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
2 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
2 — — — Not Occupied — —
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 6
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
B A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
C A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
6 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
3 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
3 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
3 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-13 (BU) No Tool Required Not Required Not Required Not Required Not Required
3 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-13 (BU) No Tool Required Not Required Not Required Not Required Not Required
3 0.5 GY/WH 5996 Driver Outside Rear View Mirror Puddle Lamp Control I —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Pending No Tool Required Not Required Not Required Not Required Not Required
3 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Pending No Tool Required Not Required Not Required Not Required Not Required
3 0.5 GY/GN 5996 Driver Outside Rear View Mirror Puddle Lamp Control I —
B A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
B A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
B A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
1 2
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
3 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
3 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
3 2
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
4
1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
1 0.5 GY/WH 3113 Heated Oxygen Sensor Heater Low Control Bank 1 Sensor 1 I —
3 0.5 WH/BK 3111 Heated Oxygen Sensor Low Signal Bank 1 Sensor 1 I —
4 0.5 VT/GY 3110 Heated Oxygen Sensor High Signal Bank 1 Sensor 1 I —
4 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
1 0.5 GY/WH 3122 Heated Oxygen Sensor Heater Low Control Bank 1 Sensor 2 I —
3 0.5 WH/YE 3121 Heated Oxygen Sensor Low Signal Bank 1 Sensor 2 I —
4 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
1 0.5 GN/YE 3212 Heated Oxygen Sensor Heater Low Control Bank 2 Sensor 1 I —
3 0.5 YE/WH 3211 Heated Oxygen Sensor Low Signal Bank 2 Sensor 1 I —
4 0.5 VT/WH 3210 Heated Oxygen Sensor High Signal Bank 2 Sensor 1 I —
4 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
1 0.5 GN/YE 3212 Heated Oxygen Sensor Heater Low Control Bank 2 Sensor 1 I —
3 0.5 YE/WH 3211 Heated Oxygen Sensor Low Signal Bank 2 Sensor 1 I —
4 0.5 VT/WH 3210 Heated Oxygen Sensor High Signal Bank 2 Sensor 1 I —
4 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
1 0.5 GN/YE 3212 Heated Oxygen Sensor Heater Low Control Bank 2 Sensor 1 I —
3 0.5 YE/WH 3211 Heated Oxygen Sensor Low Signal Bank 2 Sensor 1 I —
4 0.5 VT/WH 3210 Heated Oxygen Sensor High Signal Bank 2 Sensor 1 I —
4 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
1 0.5 WH/BN 3223 Heated Oxygen Sensor Heater Low Control Bank 2 Sensor 2 I —
3 0.5 YE/D-BU 3221 Heated Oxygen Sensor Low Signal Bank 2 Sensor 2 I —
4 0.5 VT/GN 3220 Heated Oxygen Sensor High Signal Bank 2 Sensor 2 I —
C A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
C 1 BK 250 Ground I —
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 0.5 OG/GN 2132 Left Front Side Impact Sensing Module Signal I —
2 0.5 BK/OG 6628 Left Front Side Impact Sensing Module Low Reference I —
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 0.35 OG/D-BU 6620 Left Middle Side Impact Sensing Module Signal I —
2 0.35 BK/OG 6621 Left Middle Side Impact Sensing Module Low Reference I —
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 0.5 OG/GN 2134 Right Front Side Impact Sensing Module Signal I —
2 0.5 BK/OG 6629 Right Front Side Impact Sensing Module Low Reference I —
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 0.35 OG/VT 6624 Right Middle Side Impact Sensing Module Signal I —
2 0.35 BK/OG 6625 Right Middle Side Impact Sensing Module Low Reference I —
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-34 (YE) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-34 (YE) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
3 0.5 WH/YE 3202 Throttle Inlet Absolute Pressure Sensor Low Reference I L83/L86/L8B
0.5 BK/VT 2760 Intake Air Temperature Sensor Low Reference I L96
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-65B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-65B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-65B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-42 (RD) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
B — BK 1850 Ground I —
3 1
6 4
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
II Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
6 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
B A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
6 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 2
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
1 2
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
1 4
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
1 0.5 D-BU/YE 6795 Lift Glass/Rear Compartment Lid Motor Release Control 2 I —
3 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
3 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
2 0.5 BK/D-BU 1206 Left Front Strut Position Sensor Low Reference I —
3 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
2 0.5 BK/GN 1209 Left Rear Strut Position Sensor Low Reference I —
3 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
2 0.5 BK/GY 1212 Right Front Strut Position Sensor Low Reference I —
3 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
2 0.5 BK/YE 1215 Right Rear Strut Position Sensor Low Reference I —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 6
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
6 — — — Not Occupied — —
5 1
10 6
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
1 — — — Not Occupied — —
4 1
12 5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13579954 No Tool Required J-38125-553 Not Available Not Available Not Available Not Available
2 — — — Not Occupied — —
12 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-13 (BU) No Tool Required Not Required Not Required Not Required Not Required
3 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
6 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
3 — — — Not Occupied — —
6 — — — Not Occupied — —
C A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
6 1
12 7
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 19300649 J-35616-64B (LT BU) J-38125-553 Not Available Not Available Not Available Not Available
1 — — — Not Occupied — —
12 — — — Not Occupied — —
8 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
3 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
8 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
4 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
3 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
3 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
3 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
3 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
3 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
3 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
3 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
3 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
3 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
3 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
3 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
3 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
A B
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
A B
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
A B
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
A B
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Pending No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
1 2
3 4
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-13 (BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-65B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 2
3 4
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-13 (BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-65B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 2
3 4
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-13 (BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-65B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-65B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-65B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-65B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 2
3 4
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
4 0.75 BN/BK 2295 Left Rear Heated Seat Cushion Element Low Reference I —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-65B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 2
3 4
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-13 (BU) No Tool Required Not Required Not Required Not Required Not Required
1 0.75 GN/BN 2296 Right Rear Heated Seat Cushion Element Control I —
2 0.5 BN/GN 2300 Right Rear Heated Seat Sensor Signal I X88/Z88+KA6
3 0.5 BK/GY 2301 Right Rear Heated Seat Sensor Low Reference I X88/Z88+KA6
4 0.75 GN/BK 2297 Right Rear Heated Seat Cushion Element Low Reference I X88/Z88+KA6
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-65B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 0.75 GN/BN 2296 Right Rear Heated Seat Cushion Element Control I —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-42 (RD) No Tool Required Not Required Not Required Not Required Not Required
1 2 BK 1450 Ground I —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-42 (RD) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
3 — — — Not Occupied — —
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
B A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
B A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
A B
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
D A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
D A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Pending No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Pending No Tool Required Not Required Not Required Not Required Not Required
4 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
1 2
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
1 0.35 OG/GY 5021 Right Front Head Curtain Module High Control I —
2 0.35 WH/OG 5022 Right Front Head Curtain Module Low Control I —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 2
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 2
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 2
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 2
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 2
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 2
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 0.5 OG/YE 3481 Driver Seat Belt Anchor Pretensioner High Control I —
2 0.5 YE/OG 3482 Driver Seat Belt Anchor Pretensioner Low Control I —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 0.5 OG/BN 3479 Passenger Seat Belt Anchor Pretensioner High Control I —
2 0.5 GY/OG 3480 Passenger Seat Belt Anchor Pretensioner Low Control I —
D A
H E
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
A 0.5 YE/GN 6075 Real Time Damping Air Pressure Sensor Signal I —
0.75 WH/D-BU 3261 Automatic Level Control Exhaust Solenoid Control I Z95
D — — — Not Occupied — —
F 0.5 BK/YE 6077 Real Time Damping Air Pressure Sensor Low Reference I —
H 0.5 D-BU/RD 6076 Real Time Damping Air Pressure Sensor 5V Reference I —
4 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
1 4 BK 150 Ground I —
4 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
1 4 BK 250 Ground I —
1 2
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
G13 Generator
1 2
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
2 0.75 VT/BK 7300 High Pressure Fuel Pump Actuator Low - Control I —
1 2
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
1 2
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
1 0.5 VT 901 — I —
3 0.5 GN 903 — I —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
1 0.5 VT 901 — I —
3 0.5 GN 903 — I —
3 1
6 4
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
6 1
12 7
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13575808 J-35616-2A (GY) J-38125-217 Not Available Not Available Not Available Not Available
1 0.5 VT/RD 7468 Running Boards Motor Hall Sensor Left 5V Reference I —
2 0.5 GN/RD 7464 Running Boards Motor Hall Sensor Right 5V Reference I —
5 0.5 YE/BN 7466 Running Boards Motor Hall Sensor Left Low Reference I —
6 0.5 YE/BK 7463 Running Boards Motor Hall Sensor Right Low Reference I —
7 — — — Not Occupied — —
9 — — — Not Occupied — —
11 - 12 — — — Not Occupied — —
4 1
7 5
14 8
20 15
26 21
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
III 13582297 J-35616-64B (LT BU) J-38125-22 Not Available Not Available Not Available Not Available
6 0.35 BN/WH 4046 Glove Box Door Release Relay Control III —
7 0.35 BK/YE 5005 Instrument Panel Lamp Dimmer Switch Low Reference III —
9 — — — Not Occupied — —
11 0.35 GN/BN 306 Headlamp Switch Headlamps Off Signal Control III —
0.35 D-BU/GY 192 Front Fog Lamp Switch Signal III T3U
17 — — — Not Occupied — —
20 0.35 D-BU/BK 5719 Ignition Mode Switch Start LED Signal III —
25 0.5 D-BU 2500 High Speed GMLAN Serial Data (+) 1 III —
4 1
8 5
15 9
21 16
27 22
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
II 13582297 J-35616-64B (LT BU) J-38125-22 Not Available Not Available Not Available Not Available
5 — — — Not Occupied — —
11 — — — Not Occupied — —
22 - 24 — — — Not Occupied — —
4 1
7 5
14 8
20 15
26 21
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
II 13582297 J-35616-64B (LT BU) J-38125-22 Not Available Not Available Not Available Not Available
9 - 10 — — — Not Occupied — —
4 1
7 5
14 8
20 15
26 21
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
II 13582297 J-35616-64B (LT BU) J-38125-22 Not Available Not Available Not Available Not Available
15 — — — Not Occupied — —
21 — — — Not Occupied — —
25 — — — Not Occupied — —
4 1
8 5
15 9
21 16
27 22
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
II 13582297 J-35616-64B (LT BU) J-38125-22 Not Available Not Available Not Available Not Available
III Not Required No Tool Required No Tool Required Not Available Not Available Not Available Not Available
11 — — — Not Occupied — —
14 — — — Not Occupied — —
15 0.35 GY/GN 6190 Lift Glass/Rear Compartment Lid Exterior Release Signal II —
18 - 20 — — — Not Occupied — —
23 — — — Not Occupied — —
26 — — — Not Occupied — —
3 1
9 4
16 10
21 17
26 22
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
II 13582297 J-35616-64B (LT BU) J-38125-22 Not Available Not Available Not Available Not Available
2 — — — Not Occupied — —
8 0.5 GY/GN 5996 Driver Outside Rear View Mirror Puddle Lamp Control II —
11 — — — Not Occupied — —
12 0.35 BN/WH 3269 Child Security Lock Motor Status Signal Left Rear II —
17 — — — Not Occupied — —
18 0.35 GY/BK 3268 Child Security Lock Motor Status Signal Right Rear II —
20 — — — Not Occupied — —
26 — — — Not Occupied — —
9 1
18 10
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13579977 J-35616-64B (LT BU) J-38125-553 Not Available Not Available Not Available Not Available
2 — — — Not Occupied — —
4 — — — Not Occupied — —
9 — — — Not Occupied — —
11 - 18 — — — Not Occupied — —
26
25 37
38
1 14 13
2 12 24
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13575368 J-35616-35 (VT) J-38125-557 Not Available Not Available Not Available Not Available
II 19119381 J-35616-14 (GN) J-38125-215A Not Available Not Available Not Available Not Available
III 19119560 J-35616-40 (BU) J-38125-556 Not Available Not Available Not Available Not Available
IV 19329757 J-35616-14 (GN) J-38125-215A Not Available Not Available Not Available Not Available
2 — — — Not Occupied — —
7 — — — Not Occupied — —
12 — — — Not Occupied — —
14 - 16 — — — Not Occupied — —
19 — — — Not Occupied — —
22 - 24 — — — Not Occupied — —
26 - 27 — — — Not Occupied — —
31 - 32 — — — Not Occupied — —
34 — — — Not Occupied — —
37 — — — Not Occupied — —
26
25 37
38
1 14 13
2 12 24
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13575368 J-35616-35 (VT) J-38125-557 Not Available Not Available Not Available Not Available
II 19119381 J-35616-14 (GN) J-38125-215A Not Available Not Available Not Available Not Available
III 19119560 J-35616-40 (BU) J-38125-556 Not Available Not Available Not Available Not Available
IV 19329757 J-35616-14 (GN) J-38125-215A Not Available Not Available Not Available Not Available
7 — — — Not Occupied — —
12 — — — Not Occupied — —
14 - 16 — — — Not Occupied — —
19 — — — Not Occupied — —
22 - 23 — — — Not Occupied — —
26 - 27 — — — Not Occupied — —
31 — — — Not Occupied — —
37 — — — Not Occupied — —
32 47
17 31
1 16
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13578883 J-35616-64B (LT BU) J-38125-215A Not Available Not Available Not Available Not Available
II 13579754 J-35616-42 (RD) J-38125-553 Not Available Not Available Not Available Not Available
III 13579755 J-35616-42 (RD) J-38125-553 Not Available Not Available Not Available Not Available
IV 13579766 J-35616-64B (LT BU) J-38125-215A Not Available Not Available Not Available Not Available
1 — — — Not Occupied — —
2 0.5 BK/GN 1209 Left Rear Strut Position Sensor Low Reference I —
4 0.5 BK/YE 6077 Real Time Damping Air Pressure Sensor Low Reference I —
5 0.5 BK/YE 1215 Right Rear Strut Position Sensor Low Reference I —
7 0.5 YE/GN 6075 Real Time Damping Air Pressure Sensor Signal I —
18 0.5 BK/GY 1212 Right Front Strut Position Sensor Low Reference I —
19 — — — Not Occupied — —
21 0.5 BK/D-BU 1206 Left Front Strut Position Sensor Low Reference I —
23 0.5 D-BU/RD 6076 Real Time Damping Air Pressure Sensor 5V Reference I —
29 — — — Not Occupied — —
30 0.75 WH/GN 1005 Left Front Strut Motor Decrease Damping Control IV —
31 0.75 WH/GY 1448 Left Front Strut Motor Increase Damping Control IV —
37 - 38 — — — Not Occupied — —
42 0.75 WH/BK 1013 Left Rear Strut Motor Decrease Damping Control IV —
43 0.75 BN/VT 1010 Left Rear Strut Motor Increase Damping Control IV —
44 — — — Not Occupied — —
32 16 1
73 17
52 33
72 53
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
II 13575812 J-35616-64B (LT BU) J-38125-213 Not Available Not Available Not Available Not Available
1 — — — Not Occupied — —
3 — — — Not Occupied — —
11 - 12 — — — Not Occupied — —
16 - 20 — — — Not Occupied — —
23 — — — Not Occupied — —
27 - 29 — — — Not Occupied — —
31 — — — Not Occupied — —
42 - 43 — — — Not Occupied — —
45 — — — Not Occupied — —
49 - 50 — — — Not Occupied — —
58 — — — Not Occupied — —
60 - 61 — — — Not Occupied — —
64 - 65 — — — Not Occupied — —
69 — — — Not Occupied — —
71 — — — Not Occupied — —
32 16 1
73 17
52 33
72 53
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
II 13575812 J-35616-64B (LT BU) J-38125-213 Not Available Not Available Not Available Not Available
1 — — — Not Occupied — —
3 — — — Not Occupied — —
11 - 12 — — — Not Occupied — —
16 - 20 — — — Not Occupied — —
23 — — — Not Occupied — —
27 - 29 — — — Not Occupied — —
31 — — — Not Occupied — —
42 - 43 — — — Not Occupied — —
45 — — — Not Occupied — —
49 - 50 — — — Not Occupied — —
58 — — — Not Occupied — —
60 - 61 — — — Not Occupied — —
64 - 65 — — — Not Occupied — —
69 — — — Not Occupied — —
71 — — — Not Occupied — —
14
28 15
42 29
56
43
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13575812 J-35616-64B (LT BU) J-38125-213 Not Available Not Available Not Available Not Available
1 — — — Not Occupied — —
9 — — — Not Occupied — —
15 — — — Not Occupied — —
17 — — — Not Occupied — —
21 - 23 — — — Not Occupied — —
32 — — — Not Occupied — —
35 - 37 — — — Not Occupied — —
39 — — — Not Occupied — —
42 — — — Not Occupied — —
44 — — — Not Occupied — —
46 — — — Not Occupied — —
48 - 51 — — — Not Occupied — —
54 - 55 — — — Not Occupied — —
73 32 16 1
17
52
72 33
53
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
II 13575812 J-35616-64B (LT BU) J-38125-213 Not Available Not Available Not Available Not Available
8 0.5 BN/WH 6354 Output Speed High (Replicated TOS) Input Signal II —
9 — — — Not Occupied — —
10 0.5 VT/GY 3110 Heated Oxygen Sensor High Signal Bank 1 Sensor 1 II —
11 0.5 VT/WH 3210 Heated Oxygen Sensor High Signal Bank 2 Sensor 1 II —
13 0.5 VT/GN 3220 Heated Oxygen Sensor High Signal Bank 2 Sensor 2 II —
14 — — — Not Occupied — —
17 — — — Not Occupied — —
19 - 25 — — — Not Occupied — —
26 0.5 WH/BK 3111 Heated Oxygen Sensor Low Signal Bank 1 Sensor 1 II —
27 0.5 YE/WH 3211 Heated Oxygen Sensor Low Signal Bank 2 Sensor 1 II —
28 0.5 WH/YE 3121 Heated Oxygen Sensor Low Signal Bank 1 Sensor 2 II —
29 0.5 YE/D-BU 3221 Heated Oxygen Sensor Low Signal Bank 2 Sensor 2 II —
30 - 31 — — — Not Occupied — —
33 — — — Not Occupied — —
35 — — — Not Occupied — —
41 0.5 GY/WH 3113 Heated Oxygen Sensor Heater Low Control Bank 1 Sensor 1 II —
42 0.5 GY/WH 3122 Heated Oxygen Sensor Heater Low Control Bank 1 Sensor 2 II —
45 — — — Not Occupied — —
47 - 48 — — — Not Occupied — —
50 — — — Not Occupied — —
61 0.5 GN/YE 3212 Heated Oxygen Sensor Heater Low Control Bank 2 Sensor 1 II —
62 0.5 WH/BN 3223 Heated Oxygen Sensor Heater Low Control Bank 2 Sensor 2 II —
64 — — — Not Occupied — —
66 - 68 — — — Not Occupied — —
69 0.5 WH/YE 3202 Throttle Inlet Absolute Pressure Sensor Low Reference II —
71 - 72 — — — Not Occupied — —
73 32 16 1
17
52
72 33
53
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
II 13575812 J-35616-64B (LT BU) J-38125-213 Not Available Not Available Not Available Not Available
10 0.5 VT/GY 3110 Heated Oxygen Sensor High Signal Bank 1 Sensor 1 II —
11 0.5 VT/WH 3210 Heated Oxygen Sensor High Signal Bank 2 Sensor 1 II —
12 0.5 VT/D-BU 3120 Heated Oxygen Sensor High Signal Bank 1 Sensor 2 II —
14 — — — Not Occupied — —
17 — — — Not Occupied — —
19 - 25 — — — Not Occupied — —
26 0.5 WH/BK 3111 Heated Oxygen Sensor Low Signal Bank 1 Sensor 1 II —
27 0.5 YE/WH 3211 Heated Oxygen Sensor Low Signal Bank 2 Sensor 1 II —
28 0.5 WH/YE 3121 Heated Oxygen Sensor Low Signal Bank 1 Sensor 2 II —
29 0.5 YE/D-BU 3221 Heated Oxygen Sensor Low Signal Bank 2 Sensor 2 II —
30 - 31 — — — Not Occupied — —
33 — — — Not Occupied — —
35 — — — Not Occupied — —
38 - 39 — — — Not Occupied — —
41 0.5 GY/WH 3113 Heated Oxygen Sensor Heater Low Control Bank 1 Sensor 1 II —
42 0.5 GY/WH 3122 Heated Oxygen Sensor Heater Low Control Bank 1 Sensor 2 II —
45 — — — Not Occupied — —
47 - 48 — — — Not Occupied — —
50 — — — Not Occupied — —
58 — — — Not Occupied — —
61 0.5 GN/YE 3212 Heated Oxygen Sensor Heater Low Control Bank 2 Sensor 1 II —
62 0.5 WH/BN 3223 Heated Oxygen Sensor Heater Low Control Bank 2 Sensor 2 II —
64 — — — Not Occupied — —
66 — — — Not Occupied — —
68 — — — Not Occupied — —
69 0.5 WH/YE 3202 Throttle Inlet Absolute Pressure Sensor Low Reference II —
71 - 72 — — — Not Occupied — —
73 16 1
17
52
33
72 53
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13575812 J-35616-64B (LT BU) J-38125-213 Not Available Not Available Not Available Not Available
10 — — — Not Occupied — —
12 - 14 — — — Not Occupied — —
21 - 23 — — — Not Occupied — —
26 - 27 — — — Not Occupied — —
30 - 32 — — — Not Occupied — —
37 - 39 — — — Not Occupied — —
42 — — — Not Occupied — —
46 — — — Not Occupied — —
47 0.5 WH/BK 3111 Heated Oxygen Sensor Low Signal Bank 1 Sensor 1 I —
48 0.5 YE/WH 3211 Heated Oxygen Sensor Low Signal Bank 2 Sensor 1 I —
51 — — — Not Occupied — —
52 0.5 GN/YE 3212 Heated Oxygen Sensor Heater Low Control Bank 2 Sensor 1 I —
57 - 59 — — — Not Occupied — —
62 - 66 — — — Not Occupied — —
67 0.5 VT/GY 3110 Heated Oxygen Sensor High Signal Bank 1 Sensor 1 I —
68 0.5 VT/WH 3210 Heated Oxygen Sensor High Signal Bank 2 Sensor 1 I —
71 — — — Not Occupied — —
72 0.5 GY/WH 3113 Heated Oxygen Sensor Heater Low Control Bank 1 Sensor 1 I —
53 72
33 52
73
17 32
1 16
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
II 13575812 J-35616-64B (LT BU) J-38125-213 Not Available Not Available Not Available Not Available
9 — — — Not Occupied — —
18 - 23 — — — Not Occupied — —
32 0.75 VT/BK 7300 High Pressure Fuel Pump Actuator Low - Control II —
40 - 42 — — — Not Occupied — —
45 0.75 GY/D-BU 4804 Direct Fuel Injector (DFI) High Voltage Control Cylinder 4 II —
46 0.75 D-BU 4802 Direct Fuel Injector (DFI) High Voltage Control Cylinder 2 II —
47 0.75 GN/VT 4806 Direct Fuel Injector (DFI) High Voltage Control Cylinder 6 II —
48 0.75 GY 4808 Direct Fuel Injector (DFI) High Voltage Control Cylinder 8 II —
49 0.75 GN 4803 Direct Fuel Injector (DFI) High Voltage Control Cylinder 3 II —
50 0.75 YE/GY 4807 Direct Fuel Injector (DFI) High Voltage Control Cylinder 7 II —
51 0.75 WH/GN 4805 Direct Fuel Injector (DFI) High Voltage Control Cylinder 5 II —
52 0.75 BN 4801 Direct Fuel Injector (DFI) High Voltage Control Cylinder 1 II —
54 - 58 — — — Not Occupied — —
60 - 62 — — — Not Occupied — —
65 0.75 D-BU/WH 4904 Direct Fuel Injector (DFI) High Voltage Supply Cylinder 4 II —
66 0.75 BN/GN 4902 Direct Fuel Injector (DFI) High Voltage Supply Cylinder 2 II —
67 0.75 VT 4906 Direct Fuel Injector (DFI) High Voltage Supply Cylinder 6 II —
68 0.75 WH/GN 4908 Direct Fuel Injector (DFI) High Voltage Supply Cylinder 8 II —
69 0.75 GN/BK 4903 Direct Fuel Injector (DFI) High Voltage Supply Cylinder 3 II —
70 0.75 WH/YE 4907 Direct Fuel Injector (DFI) High Voltage Supply Cylinder 7 II —
71 0.75 GN/WH 4905 Direct Fuel Injector (DFI) High Voltage Supply Cylinder 5 II —
72 0.75 BN/WH 4901 Direct Fuel Injector (DFI) High Voltage Supply Cylinder 1 II —
53 72
33 52
73
17 32
1 16
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
II 13575812 J-35616-64B (LT BU) J-38125-213 Not Available Not Available Not Available Not Available
9 — — — Not Occupied — —
20 - 23 — — — Not Occupied — —
32 0.75 VT/BK 7300 High Pressure Fuel Pump Actuator Low - Control II —
35 - 38 — — — Not Occupied — —
40 - 42 — — — Not Occupied — —
45 0.75 GY/D-BU 4804 Direct Fuel Injector (DFI) High Voltage Control Cylinder 4 II —
46 0.75 D-BU 4802 Direct Fuel Injector (DFI) High Voltage Control Cylinder 2 II —
47 0.75 GN/VT 4806 Direct Fuel Injector (DFI) High Voltage Control Cylinder 6 II —
48 0.75 GY 4808 Direct Fuel Injector (DFI) High Voltage Control Cylinder 8 II —
49 0.75 GN 4803 Direct Fuel Injector (DFI) High Voltage Control Cylinder 3 II —
50 0.75 YE/GY 4807 Direct Fuel Injector (DFI) High Voltage Control Cylinder 7 II —
51 0.75 WH/GN 4805 Direct Fuel Injector (DFI) High Voltage Control Cylinder 5 II —
52 0.75 BN 4801 Direct Fuel Injector (DFI) High Voltage Control Cylinder 1 II —
54 - 58 — — — Not Occupied — —
60 - 62 — — — Not Occupied — —
65 0.75 D-BU/WH 4904 Direct Fuel Injector (DFI) High Voltage Supply Cylinder 4 II —
66 0.75 BN/GN 4902 Direct Fuel Injector (DFI) High Voltage Supply Cylinder 2 II —
67 0.75 VT 4906 Direct Fuel Injector (DFI) High Voltage Supply Cylinder 6 II —
68 0.75 WH/GN 4908 Direct Fuel Injector (DFI) High Voltage Supply Cylinder 8 II —
69 0.75 GN/BK 4903 Direct Fuel Injector (DFI) High Voltage Supply Cylinder 3 II —
70 0.75 WH/YE 4907 Direct Fuel Injector (DFI) High Voltage Supply Cylinder 7 II —
71 0.75 GN/WH 4905 Direct Fuel Injector (DFI) High Voltage Supply Cylinder 5 II —
72 0.75 BN/WH 4901 Direct Fuel Injector (DFI) High Voltage Supply Cylinder 1 II —
53 72
33 52
73
17 32
1 16
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13575812 J-35616-64B (LT BU) J-38125-213 Not Available Not Available Not Available Not Available
11 - 15 — — — Not Occupied — —
16 0.5 WH/BN 3223 Heated Oxygen Sensor Heater Low Control Bank 2 Sensor 2 I —
18 - 21 — — — Not Occupied — —
23 - 26 — — — Not Occupied — —
31 — — — Not Occupied — —
32 0.5 GY/WH 3122 Heated Oxygen Sensor Heater Low Control Bank 1 Sensor 2 I —
33 - 37 — — — Not Occupied — —
39 - 42 — — — Not Occupied — —
47 — — — Not Occupied — —
50 - 57 — — — Not Occupied — —
59 - 62 — — — Not Occupied — —
66 0.5 YE/D-BU 3221 Heated Oxygen Sensor Low Signal Bank 2 Sensor 2 I —
67 0.5 VT/D-BU 3120 Heated Oxygen Sensor High Signal Bank 1 Sensor 2 I —
68 0.5 WH/YE 3121 Heated Oxygen Sensor Low Signal Bank 1 Sensor 2 I —
69 - 73 — — — Not Occupied — —
6 1
10 7
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
1 — — — — I —
2 0.75 GN/BN 2296 Right Rear Heated Seat Cushion Element Control I —
3 0.75 GN/BK 2297 Right Rear Heated Seat Cushion Element Low Reference I —
4 0.75 BN/BK 2295 Left Rear Heated Seat Cushion Element Low Reference I —
5 — — — — I —
6 1
10 7
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
4 0.75 GN/BN 2296 Right Rear Heated Seat Cushion Element Control I —
5 — — — Not Occupied — —
7 — — — Not Occupied — —
9 — — — Not Occupied — —
16
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
3 — — — — I —
4 — — — — I —
5 — — — — I —
10 — — — — I —
11 — — — — I —
12 — — — — I —
13 — — — — I —
14 — — — — I —
15 — — — — I —
16 — — — — I —
4 1
8 5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
6 1
10 7
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
II Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
III Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
9 — — — — I —
6 1
10 7
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
2 — — — Not Occupied — —
7 — — — Not Occupied — —
9 — — — Not Occupied — —
16
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
II Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
7 — — — — I —
11 — — — — I —
13 — — — — I —
14 — — — — I —
15 — — — — I —
16 — — — — I —
4 1
8 5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
10
20 1
11
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
5 - 12 — — — Not Occupied — —
15 - 17 — — — Not Occupied — —
10 1
20 11
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
3 — — — Not Occupied — —
20 — — — Not Occupied — —
10
20 11
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
10 — — — Not Occupied — —
14 - 15 — — — Not Occupied — —
19 — — — Not Occupied — —
10
20 11
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
8 — — — Not Occupied — —
10 — — — Not Occupied — —
16 — — — Not Occupied — —
20 — — — Not Occupied — —
1
8
16
24
17
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 19328872 J-35616-64B (LT BU) J-38125-11A Not Available Not Available Not Available Not Available
16 — — — Not Occupied — —
21 - 24 — — — Not Occupied — —
18 1
36 19
54 37
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 19328872 J-35616-64B (LT BU) J-38125-11A Not Available Not Available Not Available Not Available
9 0.35 OG/YE 3481 Driver Seat Belt Anchor Pretensioner High Control I —
10 0.35 YE/OG 3482 Driver Seat Belt Anchor Pretensioner Low Control I —
11 0.35 GY/OG 3480 Passenger Seat Belt Anchor Pretensioner Low Control I —
12 0.35 OG/BN 3479 Passenger Seat Belt Anchor Pretensioner High Control I —
17 0.35 OG/GN 5019 Left Front Head Curtain Module High Control I —
18 0.35 VT/OG 5020 Left Front Head Curtain Module Low Control I —
19 0.35 OG/GN 2132 Left Front Side Impact Sensing Module Signal I —
20 0.35 BK/OG 6628 Left Front Side Impact Sensing Module Low Reference I —
21 0.35 BK/OG 6629 Right Front Side Impact Sensing Module Low Reference I —
22 0.35 BN/OG 2134 Right Front Side Impact Sensing Module Signal I —
27 0.35 OG/D-BU 6620 Left Middle Side Impact Sensing Module Signal I —
28 0.35 BK/OG 6621 Left Middle Side Impact Sensing Module Low Reference I —
29 0.35 BK/OG 6625 Right Middle Side Impact Sensing Module Low Reference I —
31 - 36 — — — Not Occupied — —
47 - 52 — — — Not Occupied — —
53 0.35 OG/GY 5021 Right Front Head Curtain Module High Control I —
54 0.35 WH/OG 5022 Right Front Head Curtain Module Low Control I —
26 37
25
38
1
14 13
2 12 24
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 19119381 J-35616-14 (GN) J-38125-215A Not Available Not Available Not Available Not Available
II 19119772 J-35616-35 (VT) J-38125-557 Not Available Not Available Not Available Not Available
III 19353101 J-35616-40 (BU) J-38125-556 Not Available Not Available Not Available Not Available
3 0.5 BK/YE 1215 Right Rear Strut Position Sensor Low Reference I —
6 0.5 BK/GN 1209 Left Rear Strut Position Sensor Low Reference I —
9 0.5 BK/YE 6077 Real Time Damping Air Pressure Sensor Low Reference I —
10 0.5 YE/GN 6075 Real Time Damping Air Pressure Sensor Signal I —
11 - 12 — — — Not Occupied — —
15 — — — Not Occupied — —
17 — — — Not Occupied — —
18 0.5 BN 7634 Integrated Trailer Brake Controller Redundant Manual Apply Signal I —
19 0.5 BK/YE 7631 Integrated Trailer Brake Controller Switch Low Reference I —
21 0.5 GN/BK 7633 Integrated Trailer Brake Controller User Gain Signal I —
24 — — — Not Occupied — —
31 - 34 — — — Not Occupied — —
37 - 38 — — — Not Occupied — —
16
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
2 — — — Not Occupied — —
11 — — — Not Occupied — —
13 — — — Not Occupied — —
3 1
6 4
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
5 — — — Not Occupied — —
6 3 BK 1450 Ground I —
4 1
14 5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
12 — — — Not Occupied — —
14 — — — Not Occupied — —
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-42 (RD) No Tool Required Not Required Not Required Not Required Not Required
4 1
6 5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-42 (RD) No Tool Required Not Required Not Required Not Required Not Required
2 — — — Not Occupied — —
6 — — — Not Occupied — —
6 1
12 7
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
1 1.5 GN/YE 276 Driver Power Seat Recline Motor Forward Control I —
2 1.5 BU/YE 277 Driver Power Seat Recline Motor Rearward Control I —
3 1.5 GN/BN 286 Driver Power Seat Front Vertical Motor Up Control I —
4 1.5 BU/VT 287 Driver Power Seat Front Vertical Motor Down Control I —
6 1.5 GY/BU 283 Driver Power Seat Rear Vertical Motor Down Control I —
8 1.5 YE/BU 767 Driver Power Seat Lumbar Motor Down Control I —
11 1.5 YE/BU 285 Driver Power Seat Horizontal Motor Forward Control I —
12 1.5 GY/GN 284 Driver Power Seat Horizontal Motor Rearward Control I —
4 1
8 5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
13 1
26 14
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
12 0.5 BN/WH 557 Memory Seat Front Vertical Motor Position Sensor Signal I —
18 — — — Not Occupied — —
20 0.5 YE/BU 1521 Power Seat Rear Vertical Down Switch Signal I —
23 - 24 — — — Not Occupied — —
25 0.5 YE/BU 568 Memory Seat Rear Vertical Motor Position Sensor Signal I —
26 0.5 WH/BK 570 Driver Memory Seat Recline Motor Position Sensor Signal I —
10 1
20 11
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
5 — — — Not Occupied — —
8 - 10 — — — Not Occupied — —
13 - 14 — — — Not Occupied — —
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-42 (RD) No Tool Required Not Required Not Required Not Required Not Required
4 1
6 5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-42 (RD) No Tool Required Not Required Not Required Not Required Not Required
6 — — — Not Occupied — —
6 1
12 7
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
3 1.5 GN/BU 298 Passenger Power Seat Front Vertical Motor Down Control I —
4 1.5 GN/VT 297 Passenger Power Seat Front Vertical Motor Up Control I —
5 1.5 BU/WH 289 Passenger Power Seat Rear Vertical Motor Down Control I —
6 1.5 GN/WH 288 Passenger Power Seat Rear Vertical Motor Up Control I —
7 - 10 — — — Not Occupied — —
11 1.5 YE/BU 290 Passenger Power Seat Horizontal Motor Rearward Control I —
6 1
12 7
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13579944 J-35616-64B (LT BU) J-38125-215A Not Available Not Available Not Available Not Available
II 13579945 J-35616-64B (LT BU) J-38125-215A Not Available Not Available Not Available Not Available
9 — — — Not Occupied — —
4 1
8 5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
7 1
14 8
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13579944 J-35616-64B (LT BU) J-38125-215A Not Available Not Available Not Available Not Available
2 — — — Not Occupied — —
9 — — — Not Occupied — —
13 - 14 — — — Not Occupied — —
1 2
3 4
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Pending No Tool Required Not Required Not Required Not Required Not Required
4 — — — Not Occupied — —
4 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 2
3 4
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-13 (BU) No Tool Required Not Required Not Required Not Required Not Required
4 — — — Not Occupied — —
4 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
4 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 2
3 4
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-13 (BU) No Tool Required Not Required Not Required Not Required Not Required
4 — — — Not Occupied — —
4 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 2
3 4
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool
4 — — — Not Occupied — —
8 1
16 9
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 19300660 J-35616-64B (LT BU) J-38125-12A Not Available Not Available Not Available Not Available
2 — — — Not Occupied — —
5 — — — Not Occupied — —
9 — — — Not Occupied — —
16 — — — Not Occupied — —
8 1
16 9
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 19300660 J-35616-64B (LT BU) J-38125-12A Not Available Not Available Not Available Not Available
11 - 12 — — — Not Occupied — —
1 4
5 8
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
1 — — — Not Occupied — —
8 1
16 9
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
8 — — — Not Occupied — —
12 0.5 YE/WH 1695 Four Wheel Drive Wheel Lock Indicator Control I —
14 - 16 — — — Not Occupied — —
8 1
16 9
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
5 — — — Not Occupied — —
9 - 10 — — — Not Occupied — —
D A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
D 3 BK 550 Ground I —
32 16 1
65
17
48
66
64 49 33
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
II 13575812 J-35616-64B (LT BU) J-38125-213 Not Available Not Available Not Available Not Available
9 - 10 — — — Not Occupied — —
16 — — — Not Occupied — —
21 - 32 — — — Not Occupied — —
34 — — — Not Occupied — —
36 — — — Not Occupied — —
39 - 48 — — — Not Occupied — —
52 — — — Not Occupied — —
55 - 62 — — — Not Occupied — —
9
8
16
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
8 — — — Not Occupied — —
13 - 14 — — — Not Occupied — —
16 — — — Not Occupied — —
7
6
12
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
8 1
16 9
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 19300660 J-35616-64B (LT BU) J-38125-12A Not Available Not Available Not Available Not Available
6 — — — Not Occupied — —
10 — — — Not Occupied — —
11 0.5 D-BU/GN 1304 High Speed GMLAN Serial Data (+)9 I IO4/IO5/IO6
0.35 D-BU/GN 1304 High Speed GMLAN Serial Data (+)9 I UE1
12 0.5 WH/GN 1305 High Speed GMLAN Serial Data (-)9 I IO4/IO5/IO6
0.35 WH/GN 1305 High Speed GMLAN Serial Data (-)9 I UE1
15 - 16 — — — Not Occupied — —
6 1
12 7
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 19300660 J-35616-64B (LT BU) J-38125-12A Not Available Not Available Not Available Not Available
4 — — — Not Occupied — —
7 — — — Not Occupied — —
4 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
4 1
8 5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
2 — — — Not Occupied — —
5 — — — Not Occupied — —
7 — — — Not Occupied — —
A H
S J
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13575354 J-35616-14 (GN) J-38125-553 Not Available Not Available Not Available Not Available
II 13575402 J-35616-4A (PU) J-38125-553 Not Available Not Available Not Available Not Available
III 13576356 J-35616-4A (PU) J-38125-553 Not Available Not Available Not Available Not Available
E — — — Not Occupied — —
J — — — Not Occupied — —
M — — — Not Occupied — —
10 1
20 11
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13579944 J-35616-64B (LT BU) J-38125-215A Not Available Not Available Not Available Not Available
4 — — — Not Occupied — —
6 — — — Not Occupied — —
8 — — — Not Occupied — —
10
20 11
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13579944 J-35616-64B (LT BU) J-38125-215A Not Available Not Available Not Available Not Available
8 — — — Not Occupied — —
10 — — — Not Occupied — —
13 - 15 — — — Not Occupied — —
17 — — — Not Occupied — —
19 — — — Not Occupied — —
6 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
3 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
2 1
4 3
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
2 1
4 3
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
2 1
4 3
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
3 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
1 0.35 YE/BN 2097 Steering Column Tilt and Telescope Down Switch Signal I —
2 0.35 BN/GY 2096 Steering Column Tilt and Telescope Up Switch Signal I —
3 — — — Not Occupied — —
4 0.35 BU/YE 2094 Steering Column Tilt and Telescope Forward Switch Signal I —
5 — — — Not Occupied — —
8 1
16 9
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13505803 J-35616-35 (VT) J-38125-12A Not Available Not Available Not Available Not Available
II 13575808 J-35616-2A (GY) J-38125-217 Not Available Not Available Not Available Not Available
3 — — — Not Occupied — —
10 - 14 — — — Not Occupied — —
14 8
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
III 13579944 J-35616-64B (LT BU) J-38125-215A Not Available Not Available Not Available Not Available
2 0.35 GN/BN 5852 Rear Park Assist LED Disable Signal III —
6 0.5 D-BU/GY 3935 High Speed GMLAN Serial Data (+) 8 III —
7 0.5 D-BU/GY 3935 High Speed GMLAN Serial Data (+) 8 III —
13 0.5 WH/GY 3936 High Speed GMLAN Serial Data (-) 8 III —
14 0.5 WH/GY 3936 High Speed GMLAN Serial Data (-) 8 III —
16
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13579944 J-35616-64B (LT BU) J-38125-215A Not Available Not Available Not Available Not Available
5 — — — Not Occupied — —
8 — — — Not Occupied — —
13 — — — Not Occupied — —
15 — — — Not Occupied — —
8 1
16 9
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13505803 J-35616-35 (VT) J-38125-12A Not Available Not Available Not Available Not Available
II 13575808 J-35616-2A (GY) J-38125-217 Not Available Not Available Not Available Not Available
10 - 11 — — — Not Occupied — —
4 1
8 5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
3 — — — Not Occupied — —
7 0.5 VT 901 — I —
8 0.5 GN 903 — I —
4 1
8 5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
3 — — — Not Occupied — —
7 0.5 VT 901 — I —
8 0.5 GN 903 — I —
10
20 11
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13579944 J-35616-64B (LT BU) J-38125-215A Not Available Not Available Not Available Not Available
5 0.35 WH/GN 2628 Left Side Vision Camera Video Signal (+) I —
8 0.35 WH/D-BU 2627 Right Side Vision Camera Video Signal (+) I —
15 0.35 GY/GN 2625 Left Side Vision Camera Video Signal (-) I —
18 0.35 GY/D-BU 2626 Right Side Vision Camera Video Signal (-) I —
19 - 20 — — — Not Occupied — —
6 1
12 7
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13579944 J-35616-64B (LT BU) J-38125-215A Not Available Not Available Not Available Not Available
II 13579945 J-35616-64B (LT BU) J-38125-215A Not Available Not Available Not Available Not Available
III 19328872 J-35616-64B (LT BU) J-38125-11A Not Available Not Available Not Available Not Available
2 — — — Not Occupied — —
8 - 10 — — — Not Occupied — —
6 1
10 7
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
1 1.5 GN 4226 RH Third Row Seat Recline Rearward Lock Actuator Control I —
2 1.5 VT/GY 4225 RH Third Row Seat Recline Forward Lock Actuator Control I —
3 0.35 YE/BN 4214 LH Third Row Seat Recline Position Sensor Signal I —
5 0.35 WH/VT 4213 RH Third Row Seat Recline Position Sensor Signal I —
6 — — — Not Occupied — —
6 1
10 7
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
5 1.5 GY 4227 LH Third Row Seat Recline Forward Lock Actuator Control I —
6 1.5 YE/WH 4228 LH Third Row Seat Recline Rearward Lock Actuator Control I —
8 — — — — I —
3 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Pending No Tool Required Not Required Not Required Not Required Not Required
1 4
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
6 1
12 7
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
II Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
III Not Required Pending No Tool Required Not Required Not Required Not Required Not Required
3 0.35 GN/BN 5852 Rear Park Assist LED Disable Signal III —
9 — — — — I —
4 1
8 5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Pending No Tool Required Not Required Not Required Not Required Not Required
7 1
14 8
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Pending No Tool Required Not Required Not Required Not Required Not Required
2 — — — Not Occupied — —
9 — — — Not Occupied — —
13 - 14 — — — Not Occupied — —
8
1
20 9
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13579954 No Tool Required J-38125-553 Not Available Not Available Not Available Not Available
4 — — — Not Occupied — —
7 — — — Not Occupied — —
86 30
87 85
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
6 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
4 — — — Not Occupied — —
3 1
6 4
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
6 — — — Not Occupied — —
6 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
4 — — — Not Occupied — —
6 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
4 — — — Not Occupied — —
A B
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
6 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
M8 Blower Motor
4 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
3 0.5 YE/WH 1695 Four Wheel Drive Wheel Lock Indicator Control I —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
1 4
5 8
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-5 (PU) No Tool Required Not Required Not Required Not Required Not Required
1 4
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
1 0.5 BU/YE 6795 Lift Glass/Rear Compartment Lid Motor Release Control 2 I —
7 2
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
3 0.35 YE/BK 166 Power Window Master Switch Right Front Up Signal II —
5 0.35 VT/GY 2765 Power Window Switch Right Front Express Signal II —
7 0.35 BN/YE 167 Power Window Master Switch Right Front Down Signal II —
6 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
4 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
1 2
3 4
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 1.5 GN/BN 286 Driver Power Seat Front Vertical Motor Up Control I —
3 1.5 BU/VT 287 Driver Power Seat Front Vertical Motor Down Control I —
4 0.5 BN/WH 557 Memory Seat Front Vertical Motor Position Sensor Signal II —
1 2
3 4
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
1 1.5 GN/VT 297 Passenger Power Seat Front Vertical Motor Up Control I -Y91/Z75
1.5 GN/BU 298 Passenger Power Seat Front Vertical Motor Down Control I Y91/Z75-ULT
2 — — — Not Occupied — —
3 1.5 GN/BU 298 Passenger Power Seat Front Vertical Motor Down Control I -Y91/Z75
1.5 GN/VT 297 Passenger Power Seat Front Vertical Motor Up Control I Y91/Z75-ULT
4 — — — Not Occupied — —
1 2
3 4
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 1.5 YE/BU 285 Driver Power Seat Horizontal Motor Forward Control I —
3 1.5 GY/GN 284 Driver Power Seat Horizontal Motor Rearward Control I —
1 2
3 4
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
1 1.5 YE/WH 296 Passenger Power Seat Horizontal Motor Forward Control I ULT
1.5 YE/BU 290 Passenger Power Seat Horizontal Motor Rearward Control I -Y91/Z75
2 — — — Not Occupied — —
3 1.5 YE/WH 296 Passenger Power Seat Horizontal Motor Forward Control I ULT
1.5 YE/BU 290 Passenger Power Seat Horizontal Motor Rearward Control I -Y91/Z75
4 — — — Not Occupied — —
A B
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-40 (BU) No Tool Required Not Required Not Required Not Required Not Required
A B
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-40 (BU) No Tool Required Not Required Not Required Not Required Not Required
1 2
3 4
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 1.5 GY/BU 283 Driver Power Seat Rear Vertical Motor Down Control I —
4 0.5 YE/BU 568 Memory Seat Rear Vertical Motor Position Sensor Signal II —
1 2
3 4
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
1 1.5 GN/WH 288 Passenger Power Seat Rear Vertical Motor Up Control I -Y91/Z75
1.5 BU/WH 289 Passenger Power Seat Rear Vertical Motor Down Control I Y91/Z75-UTL
2 — — — Not Occupied — —
3 1.5 BU/WH 289 Passenger Power Seat Rear Vertical Motor Down Control I -Y91/Z75
1.5 GN/WH 288 Passenger Power Seat Rear Vertical Motor Up Control I Y91/Z75-UTL
4 — — — Not Occupied — —
1 2
3 4
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 1.5 GN/YE 276 Driver Power Seat Recline Motor Forward Control I —
3 1.5 BU/YE 277 Driver Power Seat Recline Motor Rearward Control I —
4 0.35 WH/BK 570 Driver Memory Seat Recline Motor Position Sensor Signal II —
1 2
3 4
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
1.5 BU/BN 77 Passenger Power Seat Recline Motor Rearward Control I Y91/Z75-ULT
2 — — — Not Occupied — —
3 1.5 BU/BN 77 Passenger Power Seat Recline Motor Rearward Control I -Y91/Z75
4 — — — Not Occupied — —
4 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
3 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
7 2
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
3 0.35 GN/WH 1300 Power Window Master Switch Left Front Up Signal II —
5 0.35 GN/VT 7628 Power Window Motor Left Front Express Control II —
7 0.35 GY 1136 Power Window Master Switch Left Front Down Signal II —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
2 2.5 YE/D-BU 669 Power Window Motor Left Rear Down Control I —
7 2
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Pending No Tool Required Not Required Not Required Not Required Not Required
3 0.35 YE/BK 166 Power Window Master Switch Right Front Up Signal I —
5 0.35 VT/GN 2765 Power Window Switch Right Front Express Signal I —
7 0.35 BN/YE 167 Power Window Master Switch Right Front Down Signal I —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
2 2.5 GN/BK 671 Power Window Motor Right Rear Down Control I —
4 5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-18 (BK) No Tool Required Not Required Not Required Not Required Not Required
5 1 BK 550 Ground II —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
2 1 BK 1050 Ground I —
1 4
5 8
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-5 (PU) No Tool Required Not Required Not Required Not Required Not Required
2 0.5 VT/RD 7468 Running Boards Motor Hall Sensor Left 5V Reference I —
4 0.5 YE/BN 7466 Running Boards Motor Hall Sensor Left Low Reference I —
6 — — — Not Occupied — —
7 0.5 GY/GN 5996 Driver Outside Rear View Mirror Puddle Lamp Control I —
1 4
5 8
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-5 (PU) No Tool Required Not Required Not Required Not Required Not Required
2 0.5 GN/RD 7464 Running Boards Motor Hall Sensor Right 5V Reference I —
4 0.5 YE/BK 7463 Running Boards Motor Hall Sensor Right Low Reference I —
6 — — — Not Occupied — —
7 0.5 GY/GN 5996 Driver Outside Rear View Mirror Puddle Lamp Control I —
4
1
8 5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
1 4 BK 1150 Ground II —
3 — — — Not Occupied — —
4
1
8 5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
1 4 BK 1250 Ground II —
3 — — — Not Occupied — —
A B
C D
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
D — — — Not Occupied — —
A B
C D
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
D — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
P12 Horn
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
6 — — — Not Occupied — —
16 1
32 17
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13575522 J-35616-64B (LT BU) J-38125-12A Not Available Not Available Not Available Not Available
II 13575782 J-35616-64B (LT BU) J-38125-12A Not Available Not Available Not Available Not Available
4 — — — Not Occupied — —
6 — — — Not Occupied — —
9 - 11 — — — Not Occupied — —
13 - 15 — — — Not Occupied — —
22 - 23 — — — Not Occupied — —
26 — — — Not Occupied — —
28 - 29 — — — Not Occupied — —
31 - 32 — — — Not Occupied — —
5 1
10 6
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
2 — — — Not Occupied — —
4 — — — Not Occupied — —
9 — — — Not Occupied — —
16
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
II 13579944 J-35616-64B (LT BU) J-38125-215A Not Available Not Available Not Available Not Available
10 - 11 — — — Not Occupied — —
13 - 15 — — — Not Occupied — —
5 1
10 6
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
2 — — — Not Occupied — —
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
1 WH/BK 1959 Left Rear Midrange Speaker (-) Low Reference I UQS
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
1 WH/BK 1959 Left Rear Midrange Speaker (-) Low Reference I UQS
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Pending No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Pending No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
1 0.75 YE/GY 1956 Left Front Tweeter Speaker (-) Low Reference I —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Pending No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Pending No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
1 0.75 VT/BN 1952 Right Front Tweeter Speaker (-) Low Reference I —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
8
1
20 9
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13579954 No Tool Required J-38125-553 Not Available Not Available Not Available Not Available
1 0.35 WH/GN 7262 Rear Seat Entertainment Channel 3 Audio Signal Right (+) I —
2 0.35 WH/VT 7260 Rear Seat Entertainment Channel 3 Audio Signal Left (+) I —
3 0.35 WH/BN 7267 Rear Seat Entertainment Channel 4 Audio Signal Right (+) I —
4 0.35 WH/D-BU 7265 Rear Seat Entertainment Channel 4 Audio Signal Left (+) I —
10 0.35 BN 7261 Rear Seat Entertainment Channel 3 Audio Signal Left (-) I —
11 0.35 BN/D-BU 7268 Rear Seat Entertainment Channel 4 Audio Signal Right (-) I —
12 0.35 BN/GY 7266 Rear Seat Entertainment Channel 4 Audio Signal Left (-) I —
17 - 18 — — — Not Occupied — —
10
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
10 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
2 3
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 — — — Not Occupied — —
4 1
8 5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Pending No Tool Required Not Required Not Required Not Required Not Required
2 — — — Not Occupied — —
5 — — — Not Occupied — —
7 — — — Not Occupied — —
1 4
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 2
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
1 2
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
1 1 BK 550 Ground I —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
10 8 3
15 1
16 2
14 9 7
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
15 — — — Not Occupied — —
16 0.5 BN/WH 6354 Output Speed High (Replicated TOS) Input Signal I —
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 0.75 WH/GY 1448 Left Front Strut Motor Increase Damping Control I —
2 0.75 WH/GN 1005 Left Front Strut Motor Decrease Damping Control I —
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 0.75 BN/VT 1010 Left Rear Strut Motor Increase Damping Control I —
2 0.75 WH/BK 1013 Left Rear Strut Motor Decrease Damping Control I —
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 0.75 WH/BK 1006 Right Front Strut Motor Increase Damping Control I —
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
6 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
6 — — — Not Occupied — —
6 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
6 — — — Not Occupied — —
5 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
B C
A D
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
3 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
6 1
12 7
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 19300660 J-35616-64B (LT BU) J-38125-12A Not Available Not Available Not Available Not Available
4 — — — Not Occupied — —
7 0.35 BK/YE 5005 Instrument Panel Lamp Dimmer Switch Low Reference I —
9 — — — Not Occupied — —
1 4
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
3 — — — Not Occupied — —
1 4
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
2 — — — Not Occupied — —
4 1
8 5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
3 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 2
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Pending No Tool Required Not Required Not Required Not Required Not Required
1 0.35 YE/BU 5797 Rear Closure Handle Switch Open Signal I TB4
1 2
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-13 (BU) No Tool Required Not Required Not Required Not Required Not Required
1 0.35 BK/VT 5801 Lift Gate Object Sensor Low Reference I TB5
2 0.35 YE/D-BU 5797 Rear Closure Handle Switch Open Signal I TB5
5 1
10 6
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
7 - 10 — — — Not Occupied — —
12 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
II 19300631 J-35616-64B (LT BU) J-38125-215A Not Available Not Available Not Available Not Available
1 — — — Not Occupied — —
6 1
10 5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13575782 J-35616-64B (LT BU) J-38125-12A Not Available Not Available Not Available Not Available
II 13575784 J-35616-64B (LT BU) J-38125-12A Not Available Not Available Not Available Not Available
9 — — — Not Occupied — —
6 1
10 5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13575782 J-35616-64B (LT BU) J-38125-12A Not Available Not Available Not Available Not Available
II 13575784 J-35616-64B (LT BU) J-38125-12A Not Available Not Available Not Available Not Available
1 — — — Not Occupied — —
6 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
II Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
2 — — — — I —
6 1
12 7
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 0.35 GY/BN 3394 Driver Mirror Position Sensor Up (+) Down (-) Signal I —
4 0.75 VT/D-BU 3390 Driver Mirror Motor Up (+) Down (-) Control I —
7 0.35 WH/YE 3395 Driver Mirror Position Sensor Left (-) Right (+) Signal I —
11 0.75 BN/BK 3389 Driver Mirror Motor Right (+) Left (-) Control I —
6 1
12 7
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 0.75 YE/VT 3397 Passenger Mirror Motor Up (+) Down (-) Control I —
4 0.75 GN/BK 3396 Passenger Mirror Motor Right (+) Left (-) Control I —
7 0.75 VT/D-BU 3390 Driver Mirror Motor Up (+) Down (-) Control I —
10 0.75 BN/BK 3389 Driver Mirror Motor Right (+) Left (-) Control I —
11 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
2 — — — Not Occupied — —
5 1
10 6
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
1 1.5 GN/BN 286 Driver Power Seat Front Vertical Motor Up Control I -A45
0.5 GN/BN 1518 Power Seat Front Vertical Up Switch Signal I A45-Y91/Z75
3 1.5 YE/BU 285 Driver Power Seat Horizontal Motor Forward Control I -A45
0.5 YE/BN 1522 Power Seat Horizontal Forward Switch Signal I A45-Y91/Z75
4 1.5 GN/YE 276 Driver Power Seat Recline Motor Forward Control I -A45
0.5 GY/BK 1269 Power Seat Recline Forward Switch Signal I A45-Y91/Z75
5 1.5 BU/VT 287 Driver Power Seat Front Vertical Motor Down Control I -A45
0.5 BU/VT 1520 Power Seat Front Vertical Down Switch Signal I A45-Y91/Z75
7 1.5 GY/GN 284 Driver Power Seat Horizontal Motor Rearward Control I -A45
0.5 GY/GN 1523 Power Seat Horizontal Rearward Switch Signal I A45-Y91/Z75
8 1.5 YE 282 Driver Power Seat Rear Vertical Motor Up Control I -A45
9 1.5 BU/YE 277 Driver Power Seat Recline Motor Rearward Control I -A45
0.5 GN/GY 1270 Power Seat Recline Rearward Switch Signal I A45-Y91/Z75
10 1.5 GY/BU 283 Driver Power Seat Rear Vertical Motor Down Control I -A45
0.5 YE/BU 1521 Power Seat Rear Vertical Down Switch Signal I A45-Y91/Z75
4 1
8 5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
2 1.5 BU 611 Driver Power Seat Lumbar Motor Forward Control I -A45
6 1.5 VT 610 Driver Power Seat Lumbar Motor Rearward Control I -A45
0.5 BU/VT 1064 Driver Seat Lumbar Rearward Switch Signal I A45-Y91/Z75
5 1
10 6
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
1 1.5 GN/BU 298 Passenger Power Seat Front Vertical Motor Down Control I —
3 1.5 YE/WH 296 Passenger Power Seat Horizontal Motor Forward Control I —
4 1.5 GN/VT 297 Passenger Power Seat Front Vertical Motor Up Control I —
6 1.5 BU/WH 289 Passenger Power Seat Rear Vertical Motor Down Control I —
8 1.5 GN/WH 288 Passenger Power Seat Rear Vertical Motor Up Control I —
5 1
10 6
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
1 — — — Not Occupied — —
3 1.5 YE/WH 296 Passenger Power Seat Horizontal Motor Forward Control I —
4 — — — Not Occupied — —
6 — — — Not Occupied — —
8 — — — Not Occupied — —
9 1.5 YE/BU 290 Passenger Power Seat Horizontal Motor Rearward Control I —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
2 — — — Not Occupied — —
4 1
8 5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
5 — — — Not Occupied — —
7 — — — Not Occupied — —
8 1.5 BU/YE 792 Passenger Power Seat Lumbar Motor Down Control I —
3 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
6 1
10 5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
3 0.35 GY/OG 5737 Adaptive Cruise Control Gap Up/Down Switch Signal I —
8 14
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
3 0.35 GY/OG 5737 Adaptive Cruise Control Gap Up/Down Switch Signal I —
6 1
10 5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
4 — — — Not Occupied — —
6 1
10 5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
4 — — — Not Occupied — —
7 — — — Not Occupied — —
1 8
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
5 — — — Not Occupied — —
4 1
8 5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
5 0.5 BN 7634 Integrated Trailer Brake Controller Redundant Manual Apply Signal I —
6 0.5 GN/BK 7633 Integrated Trailer Brake Controller User Gain Signal I —
8 0.5 BK/BN 7631 Integrated Trailer Brake Controller Switch Low Reference I —
6 1
12 7
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 19300660 J-35616-64B (LT BU) J-38125-12A Not Available Not Available Not Available Not Available
1 — — — Not Occupied — —
8 1
16 9
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
5 — — — Not Occupied — —
9 — — — Not Occupied — —
11 - 12 — — — Not Occupied — —
15 - 16 — — — Not Occupied — —
A H
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
H — — — Not Occupied — —
N M L K J
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
6 1
12 7
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
2 0.35 GN/VT 7628 Power Window Motor Left Front Express Control I —
3 0.35 GY/BK 1136 Power Window Master Switch Left Front Down Signal I —
6 0.35 GN/WH 1300 Power Window Master Switch Left Front Up Signal I —
4 1
8 5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
4 — — — Not Occupied — —
7 2.5 YE/D-BU 669 Power Window Motor Left Rear Down Control I —
9 1
18 10
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
2 0.75 YE/VT 3397 Passenger Mirror Motor Up (+) Down (-) Control I —
5 0.35 D-BU/YE 3401 Passenger Mirror Position Sensor Up (+) Down (-) Signal I —
8 0.75 GN/BK 3396 Passenger Mirror Motor Right (+) Left (-) Control I —
10 — — — Not Occupied — —
11 0.35 VT/WH 3403 Passenger Mirror Position Sensor Left (-) Right (+) Signal I —
12 — — — Not Occupied — —
14 0.35 VT/GY 2765 Power Window Switch Right Front Express Signal I —
15 0.35 BN/YE 167 Power Window Master Switch Right Front Down Signal I —
18 0.35 YE/BK 166 Power Window Master Switch Right Front Up Signal I —
6 1
12 7
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
2 0.35 VT/GY 2765 Power Window Switch Right Front Express Signal I —
3 0.35 BN/YE 167 Power Window Master Switch Right Front Down Signal I —
6 0.35 YE/BK 166 Power Window Master Switch Right Front Up Signal I —
7 - 12 — — — Not Occupied — —
4 1
8 5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
7 2.5 GN/BK 671 Power Window Motor Right Rear Down Control I —
4 1
8 5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 3
4 6
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
2 — — — Not Occupied — —
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
2 0.35 GY/GN 6190 Lift Glass/Rear Compartment Lid Exterior Release Signal I —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
B — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) Not Required Not Required Not Required Not Required Not Required
B — — — Not Occupied — —
4 1
8 5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 — — — Not Occupied — —
3 — — — Not Occupied — —
4 1
8 5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
B — — — Not Occupied — —
1 3
4 6
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
4 — — — Not Occupied — —
5 0.35 GY/BK 2546 Rear Steering Axle Control Motor Control Phase B I —
1 3
4 6
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
4 — — — Not Occupied — —
5 0.35 GY/BK 2546 Rear Steering Axle Control Motor Control Phase B I —
6 1
12 7
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
2 — — — Not Occupied — —
6 — — — Not Occupied — —
4 1
8 5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
8 1
16 9
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
1 0.75 YE/GY 1956 Left Front Tweeter Speaker (-) Low Reference I —
8 — — — Not Occupied — —
12 0.75 VT/BN 1952 Right Front Tweeter Speaker (-) Low Reference I —
13 0.75 YE/GY 1956 Left Front Tweeter Speaker (-) Low Reference I —
16 — — — Not Occupied — —
16
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13579944 J-35616-64B (LT BU) J-38125-215A Not Available Not Available Not Available Not Available
II 13579945 J-35616-64B (LT BU) J-38125-215A Not Available Not Available Not Available Not Available
3 — — — Not Occupied — —
7 — — — Not Occupied — —
9 - 11 — — — Not Occupied — —
15 — — — Not Occupied — —
16 0.75 VT/BN 1952 Right Front Tweeter Speaker (-) Low Reference II —
16 9
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13579944 J-35616-64B (LT BU) J-38125-215A Not Available Not Available Not Available Not Available
7 - 13 — — — Not Occupied — —
15 - 16 — — — Not Occupied — —
4 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
4 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
D A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
4 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
4 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
D A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
4 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
4 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
D A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
4 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
4 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
D A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
4 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
4 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
D A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
4 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
4 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
D A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
4 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
4 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
D A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
4 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
4 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
D A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
6 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
B A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
B — — — Not Occupied — —
B A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
B — — — Not Occupied — —
B A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
B — — — Not Occupied — —
B A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
B — — — Not Occupied — —
B A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
B — — — Not Occupied — —
B A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
B — — — Not Occupied — —
B A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
B — — — Not Occupied — —
B A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
B — — — Not Occupied — —
B A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
B — — — Not Occupied — —
B A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
B — — — Not Occupied — —
B A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
B — — — Not Occupied — —
B A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
B — — — Not Occupied — —
B A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
B — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
2 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
2 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
2 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
2 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
2 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
2 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
2 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
2 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
2 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
2 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
5 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
1 8
9 16
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
2 — — — Not Occupied — —
4 1 BK 1050 Ground I —
7 - 10 — — — Not Occupied — —
15 — — — Not Occupied — —
4 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
G F
C D
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-42 (RD) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
B 5 WH 22 Trailer Ground I —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
5 — — — Not Occupied — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-64B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
5 — — — Not Occupied — —
A F
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
L — — — Not Occupied — —
A F
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
H — — — Not Occupied — —
8 1
16 9
1 8
9 16
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II 19119440 J-35616-3 (GY) J-38125-217 Not Available Not Available Not Available Not Available
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
12 - 16 — — — — — Not Occupied 12 - 16 — — — — —
8 1
16 9
24 17
32 25
40 33
1 8
9
16
17 24
25
33 40 32
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
II 13575380 J-35616-3 (GY) J-38125-560 Not Available Not Available Not Available Not Available
III 19331731 J-35616-3 (GY) J-38125-560 Not Available Not Available Not Available Not Available
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
1 — — — — — Not Occupied 1 — — — — —
16 - 17 — — — — — Not Occupied 16 - 17 — — — — —
32 - 33 — — — — — Not Occupied 32 - 33 — — — — —
BK 9001 I — — — — — —
34 0.5 34 —
BK 9000 I — — — — — —
35 0.5 35 —
36 - 40 — — — — — Not Occupied 36 - 40 — — — — —
4 1
8 5
1 4
5 8
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
BK 9001 I — — BK 9001 II —
5 0.5 5 0.5
4 1
8 5
1 4
5 8
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
BK 9000 I — — BK 9000 II —
5 0.5 5 0.5
3 1
6 4
1 3
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
4 — — — — — Not Occupied 4 — — — — —
4 1
8 5
1 4
5 8
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
WH 711 I -6J7
Left Headlamp High
Beam Control
0.5
0.75
8 — — — — — Not Occupied 8 — — — — —
4 1
8 5
1 4
5 8
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
5 — — — — — Not Occupied 5 — — — — —
8 — — — — — Not Occupied 8 — — — — —
4 1
8 5
1 4
5 8
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
2 1
4 3
1 2
3 4
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
III Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
12
11 1
19
29 20
48 38
30
37
12
11
1
20
19
29
38 48
30 37
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13580829 J-35616-4A (PU) J-38125-36 Not Available Not Available Not Available Not Available
II 13580830 J-35616-4A (PU) J-38125-36 Not Available Not Available Not Available Not Available
III 19119381 J-35616-14 (GN) J-38125-215A Not Available Not Available Not Available Not Available
V 19329757 J-35616-14 (GN) J-38125-215A Not Available Not Available Not Available Not Available
VI 13505807 J-35616-19 (BK) J-38125-560 Not Available Not Available Not Available Not Available
VII 13578881 J-35616-5 (PU) J-38125-36 Not Available Not Available Not Available Not Available
VIII 13580827 J-35616-5 (PU) J-38125-36 Not Available Not Available Not Available Not Available
IX 19329756 J-35616-42 (RD) J-38125-36 Not Available Not Available Not Available Not Available
X 19352419 J-35616-19 (BK) J-38125-560 Not Available Not Available Not Available Not Available
XI 19353142 J-35616-3 (GY) J-38125-560 Not Available Not Available Not Available Not Available
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
37 — — — — — Not Occupied 37 — — — — —
39 - 41 — — — — — Not Occupied 39 - 41 — — — — —
43 - 47 — — — — — Not Occupied 43 - 47 — — — — —
8 1
16 9
1 8
9 16
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13578813 J-35616-2A (GY) J-38125-217 Not Available Not Available Not Available Not Available
II 19301767 J-35616-2A (GY) J-38125-560 Not Available Not Available Not Available Not Available
III Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
13 - 16 — — — — — Not Occupied 13 - 16 — — — — —
4 1
8 5
1 4
5 8
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
WH 311 I X88+Z88
Right Headlamp High
Beam Control
0.5
0.5
8 — — — — — Not Occupied 8 — — — — —
4 1
8 5
1 4
5 8
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
5 — — — — — Not Occupied 5 — — — — —
8 — — — — — Not Occupied 8 — — — — —
4 1
8 5
1 4
5 8
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
A F
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
BK 250 I — Ground — — — —
A 1 A —
10 1
20 11
1 10
11 20
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13575808 J-35616-2A (GY) J-38125-217 Not Available Not Available Not Available Not Available
II 19300635 J-35616-2A (GY) J-38125-217 Not Available Not Available Not Available Not Available
III 19119440 J-35616-3 (GY) J-38125-217 Not Available Not Available Not Available Not Available
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
D-BU/WH 1937 I L96+N2N Secondary Fuel Level D-BU/WH 1937 III L96+N2N
8 0.5 Sensor Signal 8 0.5
10 — — — — — Not Occupied 10 — — — — —
19 - 20 — — — — — Not Occupied 19 - 20 — — — — —
6 1
12 7
1 6
7 12
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13575808 J-35616-2A (GY) J-38125-217 Not Available Not Available Not Available Not Available
II 19119440 J-35616-3 (GY) J-38125-217 Not Available Not Available Not Available Not Available
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
1 — — — — — Not Occupied 1 — — — — —
7 — — — — — Not Occupied 7 — — — — —
2 1
1 2
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
2 — — — — — Not Occupied 2 — — — — —
33 22 17 1
36 24 19 4
1 17 20 22
33
36
4 19 21 24
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
II 19119381 J-35616-14 (GN) J-38125-215A Not Available Not Available Not Available Not Available
IV 13575380 J-35616-3 (GY) J-38125-560 Not Available Not Available Not Available Not Available
V 13580827 J-35616-5 (PU) J-38125-36 Not Available Not Available Not Available Not Available
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
8 — — — — — Not Occupied 8 — — — — —
20 - 21 — — — — — Not Occupied 20 - 21 — — — — —
24 — — — — — Not Occupied 24 — — — — —
33 - 36 — — — — — Not Occupied 33 - 36 — — — — —
8 1
15
9
23 16
1 8
15
16 23
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
II 13575380 J-35616-3 (GY) J-38125-560 Not Available Not Available Not Available Not Available
III 13580827 J-35616-5 (PU) J-38125-36 Not Available Not Available Not Available Not Available
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
9 - 10 — — — — — Not Occupied 9 - 10 — — — — —
13 — — — — — Not Occupied 13 — — — — —
17 - 19 — — — — — Not Occupied 17 - 19 — — — — —
22 — — — — — Not Occupied 22 — — — — —
4 1
8 5
1 4
5 8
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
8 — — — — — Not Occupied 8 — — — — —
6 4
3 1
4 6
1 3
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-5 (PU) No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
2 — — — — — Not Occupied 2 — — — — —
5 — — — — — Not Occupied 5 — — — — —
6 1
12 7
1 6
7 12
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13578813 J-35616-2A (GY) J-38125-217 Not Available Not Available Not Available Not Available
II Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
6 — — — — — Not Occupied 6 — — — — —
6 1
12 7
1 6
7 12
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13578813 J-35616-2A (GY) J-38125-217 Not Available Not Available Not Available Not Available
II Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
D A
H E
A D
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
D A
H E
A D
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
II Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
3 1
9 4
16 10
20 17
27 21
33 28
36 34
1 3
4 9
10 16
17
20
21 27
28 33
34 36
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Pending No Tool Required Not Required Not Required Not Required Not Required
II Not Required Pending No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
2 — — — — — Not Occupied 2 — — — — —
15 - 17 — — — — — Not Occupied 15 - 17 — — — — —
20 — — — — — Not Occupied 20 — — — — —
33 — — — — — Not Occupied 33 — — — — —
36 — — — — — Not Occupied 36 — — — — —
6 1
12 7
1 6
7 12
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13575808 J-35616-2A (GY) J-38125-217 Not Available Not Available Not Available Not Available
II Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
1 — — — — — Not Occupied 1 — — — — —
8 1
16 9
24 17
32 25
40 33
1 8
9 16
17 24
25
33 40 32
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13578884 J-35616-14 (GN) J-38125-560 Not Available Not Available Not Available Not Available
II 13580829 J-35616-4A (PU) J-38125-36 Not Available Not Available Not Available Not Available
III 19301764 J-35616-2A (GY) J-38125-553 Not Available Not Available Not Available Not Available
IV 13505807 J-35616-19 (BK) J-38125-560 Not Available Not Available Not Available Not Available
V 13575380 J-35616-3 (GY) J-38125-560 Not Available Not Available Not Available Not Available
VI 13578881 J-35616-5 (PU) J-38125-36 Not Available Not Available Not Available Not Available
VII 13580827 J-35616-5 (PU) J-38125-36 Not Available Not Available Not Available Not Available
VIII 19352419 J-35616-19 (BK) J-38125-560 Not Available Not Available Not Available Not Available
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
7 — — — — — Not Occupied 7 — — — — —
16 — — — — — Not Occupied 16 — — — — —
21 - 23 — — — — — Not Occupied 21 - 23 — — — — —
26 - 31 — — — — — Not Occupied 26 - 31 — — — — —
35 - 38 — — — — — Not Occupied 35 - 38 — — — — —
D A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
II Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
21 1
42 22
1 21
22 42
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
III 13575823 J-35616-5 (PU) J-38125-11A Not Available Not Available Not Available Not Available
IV 13575824 J-35616-5 (PU) J-38125-11A Not Available Not Available Not Available Not Available
V 19301762 J-35616-65B (LT BU) J-38125-22 Not Available Not Available Not Available Not Available
VI 19301763 J-35616-65B (LT BU) J-38125-22 Not Available Not Available Not Available Not Available
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
13 — — — — — Not Occupied 13 — — — — —
15 — — — — — Not Occupied 15 — — — — —
18 — — — — — Not Occupied 18 — — — — —
Ground
Ground
22 — — — — — Not Occupied 22 — — — — —
26 - 29 — — — — — Not Occupied 26 - 29 — — — — —
34 - 37 — — — — — Not Occupied 34 - 37 — — — — —
6 1
12 7
1 6
7 12
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13575850 J-35616-2A (GY) J-38125-11A Not Available Not Available Not Available Not Available
II 19300635 J-35616-2A (GY) J-38125-217 Not Available Not Available Not Available Not Available
III 19301756 J-35616-14 (GN) J-38125-560 Not Available Not Available Not Available Not Available
IV 13575818 J-35616-3 (GY) J-38125-553 Not Available Not Available Not Available Not Available
V 19119440 J-35616-3 (GY) J-38125-217 Not Available Not Available Not Available Not Available
VI 19300435 J-35616-14 (GN) J-38125-217 Not Available Not Available Not Available Not Available
VII 19301755 J-35616-41 (BU) J-38125-11A Not Available Not Available Not Available Not Available
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
0.5
BK/WH 2550 II — Ground
0.5
2 — — — — — Not Occupied 2 — — — — —
0.5
RD/GN 1540 II — Battery Positive Voltage
0.5
WH/D-BU 5986 VI —
Serial Data
Communication Enable
0.5
D-BU/GY 3935 V —
High Speed GMLAN
Serial Data (+) 8
0.35
WH/GY 3936 V —
High Speed GMLAN
Serial Data (-) 8
0.35
GN/YE 7066 II —
Entertainment Remote
Enable Signal
0.35
GN/YE 7066 I —
Entertainment Remote
Enable Signal
0.5
D-BU/GY 3935 V —
High Speed GMLAN
Serial Data (+) 8
0.5
WH/GY 3936 V —
High Speed GMLAN
Serial Data (-) 8
0.5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Core Crimp Insulation Crimp
I Not Available Not Available Not Available Not Available Not Available Not Available Not Available
X204 Instrument Panel Harness LVDS to Headliner Harness LVDS (U42 with DNU)
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Core Crimp Insulation Crimp
I Not Available Not Available Not Available Not Available Not Available Not Available Not Available
X204 Instrument Panel Harness LVDS to Headliner Harness LVDS (U42 without DNU)
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
4 1
1 4
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
II Not Required Pending No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
7 1
14 8
1 7
8 14
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
II 13575818 J-35616-3 (GY) J-38125-553 Not Available Not Available Not Available Not Available
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
1 — — — — — Not Occupied 1 — — — — —
14 — — — — — Not Occupied 14 — — — — —
10 1
20 11
1 10
11 20
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
III Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
11 — — — — — Not Occupied 11 — — — — —
A
B
B
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-22 (RD) No Tool Required Not Required Not Required Not Required Not Required
II Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
B — — — — — Not Occupied B — — — — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Core Crimp Insulation Crimp
I Not Available Not Available Not Available Not Available Not Available Not Available Not Available
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
1
2
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Core Crimp Insulation Crimp
I Not Available Not Available Not Available Not Available Not Available Not Available Not Available
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
21 1
42 22
1 21
22 42
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 19300649 J-35616-64B (LT BU) J-38125-553 Not Available Not Available Not Available Not Available
II 19301761 J-35616-35 (VT) J-38125-11A Not Available Not Available Not Available Not Available
III 19301761 J-35616-35 (VT) J-38125-36 Not Available Not Available Not Available Not Available
V 19301762 J-35616-65B (LT BU) J-38125-22 Not Available Not Available Not Available Not Available
VI 19301763 J-35616-65B (LT BU) J-38125-22 Not Available Not Available Not Available Not Available
VII 19329828 J-35616-5 (PU) J-38125-212 Not Available Not Available Not Available Not Available
VIII 19333310 J-35616-65B (LT BU) J-38125-553 Not Available Not Available Not Available Not Available
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
0.5
0.5
0.5
0.5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Core Crimp Insulation Crimp
I Not Available Not Available Not Available Not Available Not Available Not Available Not Available
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
4 1
8 5
1 4
5 8
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
III Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
F D
A C
D F
C A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
II Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
F — — — — — Not Occupied F — — — — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
21 1
42 22
1 21
22 42
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13582232 J-35616-64B (LT BU) J-38125-12A Not Available Not Available Not Available Not Available
II 19300649 J-35616-64B (LT BU) J-38125-11A Not Available Not Available Not Available Not Available
III 19300649 J-35616-64B (LT BU) J-38125-553 Not Available Not Available Not Available Not Available
IV 19301761 J-35616-35 (VT) J-38125-11A Not Available Not Available Not Available Not Available
V 19301761 J-35616-35 (VT) J-38125-36 Not Available Not Available Not Available Not Available
VI 13575823 J-35616-5 (PU) J-38125-11A Not Available Not Available Not Available Not Available
VII 13575824 J-35616-5 (PU) J-38125-11A Not Available Not Available Not Available Not Available
VIII 19301762 J-35616-65B (LT BU) J-38125-22 Not Available Not Available Not Available Not Available
IX 19301763 J-35616-65B (LT BU) J-38125-22 Not Available Not Available Not Available Not Available
XI 19329828 J-35616-5 (PU) J-38125-212 Not Available Not Available Not Available Not Available
XII 19329836 J-35616-35 (VT) J-38125-12A Not Available Not Available Not Available Not Available
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
GY/VT 755 III — RAP Relay Coil Control GY/VT 755 VIII —
19 0.35 19 0.35
YE/BK 117 VI —
Right Front Speaker
Signal (-) 1
0.75
WH/D-BU 5986 IV —
Serial Data
Communication Enable
0.5
GN 6820 II — GN 6820 IX —
0.75 0.75
YE 200 VI —
Right Front Speaker
Control (+) 1
0.75
6 1
12 7
1 6
7 12
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13578891 J-35616-2A (GY) J-38125-11A Not Available Not Available Not Available Not Available
II 19119440 J-35616-3 (GY) J-38125-217 Not Available Not Available Not Available Not Available
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
9 - 12 — — — — — Not Occupied 9 - 12 — — — — —
21 1
42 22
1 21
22 42
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 19300649 J-35616-64B (LT BU) J-38125-11A Not Available Not Available Not Available Not Available
II 19300649 J-35616-64B (LT BU) J-38125-553 Not Available Not Available Not Available Not Available
III 19301761 J-35616-35 (VT) J-38125-11A Not Available Not Available Not Available Not Available
IV 19301761 J-35616-35 (VT) J-38125-36 Not Available Not Available Not Available Not Available
V Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
VI Not Required J-35616-5 (PU) No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
15 — — — — — Not Occupied 15 — — — — —
18 - 19 — — — — — Not Occupied 18 - 19 — — — — —
Run/Crank Ignition 1
Voltage
36 — — — — — Not Occupied 36 — — — — —
39 - 40 — — — — — Not Occupied 39 - 40 — — — — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required No Tool Required No Tool Required Not Required Not Required Not Required Not Required
X301 Instrument Panel Harness USB to Floor console Harness USB (D07/DCK with U42)
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
X Y
Y X
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Core Crimp Insulation Crimp
I Not Available Not Available Not Available Not Available Not Available Not Available Not Available
X302 Floor Console Harness USB to Instrument Panel Harness USB (D07/DCK with U42)
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Core Crimp Insulation Crimp
I Not Available Not Available Not Available Not Available Not Available Not Available Not Available
X302 Floor Console Harness USB to Instrument Panel Harness USB (D07/DCK without U42)
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
X Y
Y X
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required No Tool Required No Tool Required Not Required Not Required Not Required Not Required
X303 Floor Console Extension Harness USB to Instrument Panel Harness USB (D07/DCK with U42)
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Core Crimp Insulation Crimp
I Not Available Not Available Not Available Not Available Not Available Not Available Not Available
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
6 1
12 7
1
6
7 12
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13575838 J-35616-35 (VT) J-38125-11A Not Available Not Available Not Available Not Available
III 13575839 J-35616-35 (VT) J-38125-11A Not Available Not Available Not Available Not Available
IV 19301761 J-35616-35 (VT) J-38125-11A Not Available Not Available Not Available Not Available
V 19301761 J-35616-35 (VT) J-38125-36 Not Available Not Available Not Available Not Available
VI Not Required J-35616-5 (PU) No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
1 — — — — — Not Occupied 1 — — — — —
1.5
2.5
1.5
BK 1050 II — Ground
2.5
D-BU/BN 6807 I —
DC To AC Inverter
Control
0.35
3 1
6 4
1 3
4 6
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
III Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
IV Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
120 V AC Phase A
120 V AC Phase B
0.5
14 8
1 7
8 14
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
III Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
IV Not Required J-35616-5 (PU) No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
6 — — — — — Not Occupied 6 — — — — —
0.5 0.5
6 1
12 7
1 6
7 12
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Available No Tool Required Not Available Not Required Not Required Not Required Not Required
II Not Required No Tool Required No Tool Required Not Required Not Required Not Required Not Required
III Not Required Pending No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
— — I — — — — III —
11 — 11 —
— — I — — — — III —
12 — 12 —
4 1
8 5
1 4
5 8
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
7 — — — — — Not Occupied 7 — — — — —
12
11 1
19
29 20
48 38
30
37
12
1 11
20
19
29
38 48
30 37
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
II 19352419 J-35616-19 (BK) J-38125-560 Not Available Not Available Not Available Not Available
III 19353142 J-35616-3 (GY) J-38125-560 Not Available Not Available Not Available Not Available
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
8 - 23 — — — — — Not Occupied 8 - 23 — — — — —
26 - 32 — — — — — Not Occupied 26 - 32 — — — — —
35 - 48 — — — — — Not Occupied 35 - 48 — — — — —
12
11 1
19
29 20
48 38
30
37
12
1 11
20
19
29
38 48
30 37
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-40 (BU) No Tool Required Not Required Not Required Not Required Not Required
III Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
IV Not Required J-35616-19 (BK) No Tool Required Not Required Not Required Not Required Not Required
V Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
VI Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
VII Not Required J-35616-32 (OR) No Tool Required Not Required Not Required Not Required Not Required
VIII Not Required J-35616-34 (YE) No Tool Required Not Required Not Required Not Required Not Required
IX Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
X Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
1 — — — — — Not Occupied 1 — — — — —
8 — — — — — Not Occupied 8 — — — — —
12 — — — — — Not Occupied 12 — — — — —
16 — — — — — Not Occupied 16 — — — — —
18 — — — — — Not Occupied 18 — — — — —
20 - 21 — — — — — Not Occupied 20 - 21 — — — — —
29 — — — — — Not Occupied 29 — — — — —
31 — — — — — Not Occupied 31 — — — — —
38 - 39 — — — — — Not Occupied 38 - 39 — — — — —
45 — — — — — Not Occupied 45 — — — — —
48 — — — — — Not Occupied 48 — — — — —
12
11 1
19
29 20
48 38
30
37
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-19 (BK) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
III Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
IV Not Required J-35616-34 (YE) No Tool Required Not Required Not Required Not Required Not Required
V Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
VI Not Required J-35616-40 (BU) No Tool Required Not Required Not Required Not Required Not Required
VII Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
VIII Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
IX Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
X Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
XI Not Required J-35616-32 (OR) No Tool Required Not Required Not Required Not Required Not Required
XII Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
1 — — — — — Not Occupied 1 — — — — —
12 — — — — — Not Occupied 12 — — — — —
16 — — — — — Not Occupied 16 — — — — —
18 — — — — — Not Occupied 18 — — — — —
20 - 22 — — — — — Not Occupied 20 - 22 — — — — —
YE/OG 3482 VIII — Driver Seat Belt Anchor YE/OG 3482 III —
25 0.5 Pretensioner Low 25 0.35
Control
27 - 32 — — — — — Not Occupied 27 - 32 — — — — —
OG/YE 3481 VIII — Driver Seat Belt Anchor OG/YE 3481 III —
36 - 39 — — — — — Not Occupied 36 - 39 — — — — —
42 — — — — — Not Occupied 42 — — — — —
45 — — — — — Not Occupied 45 — — — — —
48 — — — — — Not Occupied 48 — — — — —
12
1 11
20
19
29
38 48
30 37
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
III Not Required J-35616-40 (BU) No Tool Required Not Required Not Required Not Required Not Required
IV Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
V 13505807 J-35616-19 (BK) J-38125-560 Not Available Not Available Not Available Not Available
VI 13575380 J-35616-3 (GY) J-38125-560 Not Available Not Available Not Available Not Available
VII 13578881 J-35616-5 (PU) J-38125-36 Not Available Not Available Not Available Not Available
VIII 19329756 J-35616-42 (RD) J-38125-36 Not Available Not Available Not Available Not Available
IX 19331731 J-35616-3 (GY) J-38125-560 Not Available Not Available Not Available Not Available
X 19352419 J-35616-19 (BK) J-38125-560 Not Available Not Available Not Available Not Available
XI 19353142 J-35616-3 (GY) J-38125-560 Not Available Not Available Not Available Not Available
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
1 — — — — — Not Occupied 1 — — — — —
8 — — — — — Not Occupied 8 — — — — —
12 — — — — — Not Occupied 12 — — — — —
16 — — — — — Not Occupied 16 — — — — —
18 — — — — — Not Occupied 18 — — — — —
20 - 22 — — — — — Not Occupied 20 - 22 — — — — —
27 - 32 — — — — — Not Occupied 27 - 32 — — — — —
38 - 39 — — — — — Not Occupied 38 - 39 — — — — —
42 — — — — — Not Occupied 42 — — — — —
45 — — — — — Not Occupied 45 — — — — —
48 — — — — — Not Occupied 48 — — — — —
3 1
6 4
1 3
4 6
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-5 (PU) No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
BU 611 I —
VT 610 I —
7 1
14 8
1 7
8 14
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
III Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
IV Not Required J-35616-5 (PU) No Tool Required Not Required Not Required Not Required Not Required
X312 Driver Seat Back Harness to Driver Seat Cushion Harness (Z75+ULT)
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
8 — — — — — Not Occupied 8 — — — — —
13 - 14 — — — — — Not Occupied 13 - 14 — — — — —
6 1
12 7
1 6
7 12
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
X312 Driver Seat Back Harness to Driver Seat Cushion Harness (Z75-ULT)
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
8 - 10 — — — — — Not Occupied 8 - 10 — — — — —
2 1
1 2
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
X312 Driver Seat Back Harness to Driver Seat Cushion Harness X88/Z88-(AG1/A45/KQV)
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
8 1
16 9
1 8
9 16
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
X312 Driver Seat Back Harness to Driver Seat Cushion Harness X88/Z88+(AG1/A45/KQV)
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
1 3
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
III Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
IV Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
VT/YE 43 III —
Accessory Ignition
GN 4512 III —
Wireless Charging
System Charge 0.35
Indicator Control
8 1
16 9
1 8
9 16
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13578891 J-35616-2A (GY) J-38125-11A Not Available Not Available Not Available Not Available
II 13575818 J-35616-3 (GY) J-38125-553 Not Available Not Available Not Available Not Available
III 19119440 J-35616-3 (GY) J-38125-217 Not Available Not Available Not Available Not Available
IV 19301755 J-35616-41 (BU) J-38125-11A Not Available Not Available Not Available Not Available
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
GY/VT 3808 II —
Front Object Sensor
Control 2
0.35
16 — — — — — Not Occupied 16 — — — — —
8 1
16 9
26 17
1 8
9 16
17 26
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13575850 J-35616-2A (GY) J-38125-11A Not Available Not Available Not Available Not Available
II 13578891 J-35616-2A (GY) J-38125-11A Not Available Not Available Not Available Not Available
IV 13582322 J-35616-35 (VT) J-38125-11A Not Available Not Available Not Available Not Available
V Not Required J-35616-3 (GY) J-38125-217 Not Required Not Required Not Required Not Required
VI Not Required J-35616-3 (GY) J-38125-553 Not Required Not Required Not Required Not Required
VII Not Required J-35616-5 (PU) J-38125-212 Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
3 — — — — — Not Occupied 3 — — — — —
WH/BN 6815 VI —
Inadvertent Power
Control
0.5
8 — — — — — Not Occupied 8 — — — — —
19 - 20 — — — — — Not Occupied 19 - 20 — — — — —
0.5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-65B (LT BU) J-38125-212 Not Required Not Required Not Required Not Required
III Not Required J-35616-65B (LT BU) J-38125-217 Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
2 1
1 2
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-5 (PU) No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
12
11 1
19
29 20
48 38
30
37
12
1 11
20
19
29
38 48
30 37
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-40 (BU) No Tool Required Not Required Not Required Not Required Not Required
III Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
IV 13505807 J-35616-19 (BK) J-38125-560 Not Available Not Available Not Available Not Available
V 19352419 J-35616-19 (BK) J-38125-560 Not Available Not Available Not Available Not Available
VI 19353142 J-35616-3 (GY) J-38125-560 Not Available Not Available Not Available Not Available
VII Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
VIII Not Required J-35616-32 (OR) No Tool Required Not Required Not Required Not Required Not Required
IX Not Required No Tool Required No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
1 — — — — — Not Occupied 1 — — — — —
8 - 10 — — — — — Not Occupied 8 - 10 — — — — —
12 - 13 — — — — — Not Occupied 12 - 13 — — — — —
16 - 23 — — — — — Not Occupied 16 - 23 — — — — —
27 - 32 — — — — — Not Occupied 27 - 32 — — — — —
37 - 48 — — — — — Not Occupied 37 - 48 — — — — —
12
1 11
20
19
29
38 48
30 37
12
1 11
20
19
29
38 48
30 37
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I — J-35616-14 (GN) No Tool Required Not Available Not Available Not Available Not Available
II — J-35616-32 (OR) No Tool Required Not Available Not Available Not Available Not Available
III 13327190 J-35616-3 (GY) No Tool Required Not Available Not Available Not Available Not Available
V 13579985 J-35616-3 (GY) No Tool Required Not Available Not Available Not Available Not Available
VI 19301761 J-35616-35 (VT) No Tool Required Not Available Not Available Not Available Not Available
VII 19332365 J-35616-19 (BK) No Tool Required Not Available Not Available Not Available Not Available
VIII Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
IX Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
X Not Required J-35616-40 (BU) No Tool Required Not Required Not Required Not Required Not Required
XI Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
XII 19301761 J-35616-35 (VT) J-38125-11A Not Available Not Available Not Available Not Available
XIII 19301767 J-35616-2A (GY) J-38125-560 Not Available Not Available Not Available Not Available
XIV 19332365 J-35616-19 (BK) J-38125-560 Not Available Not Available Not Available Not Available
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
1 — — — — — Not Occupied 1 — — — — —
10 — — — — — Not Occupied 10 — — — — —
12 - 13 — — — — — Not Occupied 12 - 13 — — — — —
16 — — — — — Not Occupied 16 — — — — —
18 — — — — — Not Occupied 18 — — — — —
20 - 21 — — — — — Not Occupied 20 - 21 — — — — —
23 — — — — — Not Occupied 23 — — — — —
29 — — — — — Not Occupied 29 — — — — —
31 — — — — — Not Occupied 31 — — — — —
37 - 45 — — — — — Not Occupied 37 - 45 — — — — —
48 — — — — — Not Occupied 48 — — — — —
12
1 11
20
19
29
38 48
30 37
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
III Not Required J-35616-40 (BU) No Tool Required Not Required Not Required Not Required Not Required
IV 13505807 J-35616-19 (BK) J-38125-560 Not Available Not Available Not Available Not Available
V 13575380 J-35616-3 (GY) J-38125-560 Not Available Not Available Not Available Not Available
VI 19352419 J-35616-19 (BK) J-38125-560 Not Available Not Available Not Available Not Available
VII 19353142 J-35616-3 (GY) J-38125-560 Not Available Not Available Not Available Not Available
VIII Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
IX Not Required J-35616-32 (OR) No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
1 — — — — — Not Occupied 1 — — — — —
8 - 10 — — — — — Not Occupied 8 - 10 — — — — —
12 — — — — — Not Occupied 12 — — — — —
16 — — — — — Not Occupied 16 — — — — —
18 — — — — — Not Occupied 18 — — — — —
20 - 22 — — — — — Not Occupied 20 - 22 — — — — —
27 - 32 — — — — — Not Occupied 27 - 32 — — — — —
37 - 45 — — — — — Not Occupied 37 - 45 — — — — —
47 - 48 — — — — — Not Occupied 47 - 48 — — — — —
12
11 1
19
29 20
48 38
30
37
12
1 11
20
19
29
38 48
30 37
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-40 (BU) No Tool Required Not Required Not Required Not Required Not Required
III Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
IV — J-35616-32 (OR) No Tool Required Not Available Not Available Not Available Not Available
V 13327190 J-35616-3 (GY) No Tool Required Not Available Not Available Not Available Not Available
VII 13579985 J-35616-3 (GY) No Tool Required Not Available Not Available Not Available Not Available
VIII 13582297 J-35616-64B (LT BU) No Tool Required Not Available Not Available Not Available Not Available
IX 19301761 J-35616-35 (VT) J-38125-11A Not Available Not Available Not Available Not Available
X 19301761 J-35616-35 (VT) No Tool Required Not Available Not Available Not Available Not Available
XI 19301767 J-35616-2A (GY) J-38125-560 Not Available Not Available Not Available Not Available
XII 19332365 J-35616-19 (BK) J-38125-560 Not Available Not Available Not Available Not Available
XIII 19332365 J-35616-19 (BK) No Tool Required Not Available Not Available Not Available Not Available
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
1 — — — — — Not Occupied 1 — — — — —
10 — — — — — Not Occupied 10 — — — — —
12 - 13 — — — — — Not Occupied 12 - 13 — — — — —
18 — — — — — Not Occupied 18 — — — — —
20 - 23 — — — — — Not Occupied 20 - 23 — — — — —
28 - 32 — — — — — Not Occupied 28 - 32 — — — — —
37 - 45 — — — — — Not Occupied 37 - 45 — — — — —
48 — — — — — Not Occupied 48 — — — — —
3 1
6 4
1 3
4 6
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-5 (PU) No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
BU 211 I —
VT 210 I —
7 1
14 8
1 7
8 14
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
III Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
IV Not Required J-35616-5 (PU) No Tool Required Not Required Not Required Not Required Not Required
X322 Passenger Seat Back Harness to Passenger Seat Cushion Harness (Z75+ULT)
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
13 - 14 — — — — — Not Occupied 13 - 14 — — — — —
3 1
6 4
1 3
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
X322 Passenger Seat Back Harness to Passenger Seat Cushion Harness (Z75-ULT)
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
0.75 0.75
6 — — — — — Not Occupied 6 — — — — —
2 1
1 2
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
X322 Passenger Seat Back Harness to Passenger Seat Cushion Harness X88/Z88-(AG2/A45/KQV)
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
6 1
12 7
1 6
7 12
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
X322 Passenger Seat Back Harness to Passenger Seat Cushion Harness X88/Z88+(AG2/A45/KQV)
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
10 - 12 — — — — — Not Occupied 10 - 12 — — — — —
5 1
10 6
6 10
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-3 (GY) J-38125-217 Not Required Not Required Not Required Not Required
III Not Required J-35616-5 (PU) J-38125-212 Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
1 — — — — — Not Occupied 1 — — — — —
5 — — — — — Not Occupied 5 — — — — —
9 - 10 — — — — — Not Occupied 9 - 10 — — — — —
6 4
3 1
4 6
1 3
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-4A (PU) No Tool Required Not Required Not Required Not Required Not Required
II Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
6 4
3 1
4 6
1 3
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Core Crimp Insulation Crimp
I Not Available J-35616-35 (VT) Not Available Not Available Not Available Not Available Not Available
II Not Available J-35616-64B (L-BU) Not Available Not Available Not Available Not Available Not Available
III Not Available J-35616-5 (PU) Not Available Not Available Not Available Not Available Not Available
IV Not Available Not Available Not Available Not Available Not Available Not Available Not Available
X340 3rd Row Seat Right Harness to 3rd Row Seat Left Harness (AS8)
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
4 1.5 L-BU 4217 I - RH Third Row Seat 4 1.5 L-BU 4217 III -
Recline Motor Forward
Control
6 1.5 L-GN 4226 I - RH Third Row Seat 6 1.5 L-GN 4226 III -
Recline Rearward Lock
Actuator Control
8 1
16 9
2 7
1 8
9 16
10 15
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
III 19119440 J-35616-3 (GY) J-38125-217 Not Available Not Available Not Available Not Available
IV 19300435 J-35616-41 (BU) J-38125-11A Not Available Not Available Not Available Not Available
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
2 — — — — — Not Occupied 2 — — — — —
7 — — — — — Not Occupied 7 — — — — —
10 — — — — — Not Occupied 10 — — — — —
13 — — — — — Not Occupied 13 — — — — —
15 — — — — — Not Occupied 15 — — — — —
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required No Tool Required No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required No Tool Required No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
1 5
6 10
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
II 19333324 J-35616-13 (BU) J-38125-12A Not Available Not Available Not Available Not Available
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
4 1
8 5
1 4
5 8
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
2 — — — — — Not Occupied 2 — — — — —
7 — — — — — Not Occupied 7 — — — — —
2 1
1 2
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
II Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) Not Required Not Required Not Required Not Required Not Required
II Not Required Pending No Tool Required Not Required Not Required Not Required Not Required
X390 Body Harness to Driver Roof Rail Air Bag Jumper Harness
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
6 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
6 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required No Tool Required No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required No Tool Required No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
B A
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-34 (YE) No Tool Required Not Required Not Required Not Required Not Required
X485 Center High Mounted Stop Lamp Jumper Harness to Body Harness
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
— — — — Ground BK 1450 II —
2 — 2 1
BK 1450 I — Ground — — — —
B 0.5 B —
2 1
1 2
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
7 1
14 8
1 7
8 14
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13575838 J-35616-35 (VT) J-38125-11A Not Available Not Available Not Available Not Available
III 19300635 J-35616-2A (GY) J-38125-217 Not Available Not Available Not Available Not Available
IV Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
8 — — — — — Not Occupied 8 — — — — —
4 1
8 5
1 4
8
5
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-5 (PU) No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
8 1
16 9
24 17
32 25
40 33
1 8
9
16
17 24
25
33 40 32
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I 13576369 J-35616-14 (GN) J-38125-560 Not Available Not Available Not Available Not Available
II 13580830 J-35616-4A (PU) J-38125-36 Not Available Not Available Not Available Not Available
IV 13580834 J-35616-14 (GN) J-38125-560 Not Available Not Available Not Available Not Available
V 13584463 J-35616-4A (PU) J-38125-36 Not Available Not Available Not Available Not Available
VI Not Required J-35616-34 (YE) No Tool Required Not Required Not Required Not Required Not Required
VII Not Required J-35616-5 (PU) No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
0.5
Ground
10 — — — — — Not Occupied 10 — — — — —
GY 5861 II —
Passenger Side Object
Detection LED Signal 1
0.35
24 - 40 — — — — — Not Occupied 24 - 40 — — — — —
2 41
28
1 15
41 29
2
28
16
1
15 3
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-42 (RD) No Tool Required Not Required Not Required Not Required Not Required
III 13575556 J-35616-34 (YE) J-38125-560 Not Available Not Available Not Available Not Available
IV 13575706 J-35616-42 (RD) J-38125-36 Not Available Not Available Not Available Not Available
V 13575775 J-35616-34 (YE) J-38125-560 Not Available Not Available Not Available Not Available
VIII 13582220 J-35616-14 (GN) J-38125-560 Not Available Not Available Not Available Not Available
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
0.5 0.5
WH 6816 V —
Indicator Dimming
Control
0.35
1
12
13
24
36 25
48 37
1 12
13 24
25 36
37 48
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
III Not Required J-35616-13 (BU) No Tool Required Not Required Not Required Not Required Not Required
IV Not Required J-35616-5 (PU) No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
4 — — — — — Not Occupied 4 — — — — —
15 - 16 — — — — — Not Occupied 15 - 16 — — — — —
18 - 19 — — — — — Not Occupied 18 - 19 — — — — —
24 — — — — — Not Occupied 24 — — — — —
27 - 28 — — — — — Not Occupied 27 - 28 — — — — —
35 — — — — — Not Occupied 35 — — — — —
1
6
12 7
18 13
1 6
7 12
13 18
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-65B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
6 — — — — — Not Occupied 6 — — — — —
1 3
4 6
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-17 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
X515 Left Outside Rearview Mirror Camera Jumper Harness to Driver Door Harness
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
2 41
28
1 15
41 29
2
28
16
1
15 3
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-42 (RD) No Tool Required Not Required Not Required Not Required Not Required
III 13575556 J-35616-34 (YE) J-38125-560 Not Available Not Available Not Available Not Available
IV 13575775 J-35616-34 (YE) J-38125-560 Not Available Not Available Not Available Not Available
VII 13575857 J-35616-42 (RD) J-38125-36 Not Available Not Available Not Available Not Available
VIII 13582220 J-35616-14 (GN) J-38125-560 Not Available Not Available Not Available Not Available
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
5 — — — — — Not Occupied 5 — — — — —
16 — — — — — Not Occupied 16 — — — — —
21 — — — — — Not Occupied 21 — — — — —
24 — — — — — Not Occupied 24 — — — — —
32 — — — — — Not Occupied 32 — — — — —
1
12
13
24
36 25
48 37
1 12
13 24
25 36
37 48
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
III Not Required J-35616-13 (BU) No Tool Required Not Required Not Required Not Required Not Required
IV Not Required J-35616-5 (PU) No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
15 - 16 — — — — — Not Occupied 15 - 16 — — — — —
18 - 19 — — — — — Not Occupied 18 - 19 — — — — —
23 - 28 — — — — — Not Occupied 23 - 28 — — — — —
32 - 36 — — — — — Not Occupied 32 - 36 — — — — —
40 - 46 — — — — — Not Occupied 40 - 46 — — — — —
1
6
12 7
18 13
1 6
7 12
13 18
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-65B (LT BU) No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
2 — — — — — Not Occupied 2 — — — — —
YE/GY 3413 II
A45+DL3/DR4
0.5
6 — — — — — Not Occupied 6 — — — — —
16 — — — — — Not Occupied 16 — — — — —
0.5
1 3
4 6
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required Not Available No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-17 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
1 2
20
11
20 12
11 3 2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-42 (RD) No Tool Required Not Required Not Required Not Required Not Required
III 13575556 J-35616-34 (YE) J-38125-560 Not Available Not Available Not Available Not Available
IV 13575706 J-35616-42 (RD) J-38125-36 Not Available Not Available Not Available Not Available
V 13575775 J-35616-34 (YE) J-38125-560 Not Available Not Available Not Available Not Available
VIII 13582220 J-35616-14 (GN) J-38125-560 Not Available Not Available Not Available Not Available
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
GN 199 III —
Left Rear Speaker
Control (+)
1
12 — — — — — Not Occupied 12 — — — — —
15 — — — — — Not Occupied 15 — — — — —
17 - 18 — — — — — Not Occupied 17 - 18 — — — — —
3 1
6 4
1 3
4 6
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
III Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
X705 Left Rear Door Harness to Left Rear Door Trim Harness
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
1 — — — — — Not Occupied 1 — — — — —
4 — — — — — Not Occupied 4 — — — — —
1 2
20
11
20 12
11 3 2 1
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-42 (RD) No Tool Required Not Required Not Required Not Required Not Required
III 13575556 J-35616-34 (YE) J-38125-560 Not Available Not Available Not Available Not Available
IV 13575775 J-35616-34 (YE) J-38125-560 Not Available Not Available Not Available Not Available
VII 13582220 J-35616-14 (GN) J-38125-560 Not Available Not Available Not Available Not Available
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
WH 46 III —
Right Rear Speaker
Control (+)
1
12 — — — — — Not Occupied 12 — — — — —
15 — — — — — Not Occupied 15 — — — — —
17 - 18 — — — — — Not Occupied 17 - 18 — — — — —
3 1
6 4
1 3
4 6
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-2A (GY) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
III Not Required J-35616-14 (GN) No Tool Required Not Required Not Required Not Required Not Required
IV Not Required J-35616-3 (GY) No Tool Required Not Required Not Required Not Required Not Required
X805 Right Rear Door Harness to Right Rear Door Trim Harness
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
1 — — — — — Not Occupied 1 — — — — —
4 — — — — — Not Occupied 4 — — — — —
11 1
24
12
36 25
1
11
12
24
25 36
18
Terminal Type ID Terminated Lead Diagnostic Test Probe Terminal Removal Tool Service Terminal Tray Name Core Crimp Insulation Crimp
I Not Required J-35616-16 (LT GN) No Tool Required Not Required Not Required Not Required Not Required
II Not Required J-35616-35 (VT) No Tool Required Not Required Not Required Not Required Not Required
III Not Required J-35616-42 (RD) No Tool Required Not Required Not Required Not Required Not Required
V 13575823 J-35616-5 (PU) J-38125-11A Not Available Not Available Not Available Not Available
VI 13575824 J-35616-5 (PU) J-38125-11A Not Available Not Available Not Available Not Available
VIII 13580023 J-35616-43 (RD) J-38125-11A Not Available Not Available Not Available Not Available
IX 19329830 J-35616-13 (BU) J-38125-12A Not Available Not Available Not Available Not Available
Pin Size Color Circuit Terminal Type Option Function Pin Size Color Circuit Terminal Type Option
ID ID
5 — — — — — Not Occupied 5 — — — — —
7 — — — — — Not Occupied 7 — — — — —
9 — — — — — Not Occupied 9 — — — — —
12 — — — — — Not Occupied 12 — — — — —
Ground BK 2550 IX —
0.75
21 — — — — — Not Occupied 21 — — — — —
23 — — — — — Not Occupied 23 — — — — —
31 — — — — — Not Occupied 31 — — — — —
0.5
WH/D-BU 6973 IX —
Camera Signal 2
0.35
GY/YE 6972 IX —
Camera Signal 2 +
0.35
0.35
S39
Ignition
Switch
K9
Body
Control
Module
KR75
Engine
Controls
Ignition
Relay
Power to many of this vehicles circuits is controlled by the module that is designated the power mode master. This vehicles power mode master is the body control module (BCM). The BCM has multiple B+ circuits that feed into
it. Each of those circuits are partitioned within the controller to drive certain outputs of the vehicle’s body functions. An open or short in any one of the B+ circuits may induce multiple codes/or a section of non-functionality
within the BCM with the rest of the BCM functioning normally. In this case it is useful to refer to the power distribution schematics to determine if the non-functional partition of the controller shares a common B+ circuit. The
ignition switch is a low current switch with multiple discrete ignition switch signals to the power mode master for determination of the power mode that will be sent over the serial data circuits to the other modules that need this
information. The power mode master will also activate relays and other direct outputs of the power mode master as needed. The power mode master determines which power mode (Off, Accessory, Run, Crank Request) is
required, and reports this information to other modules via serial data. Modules which have switched voltage inputs may operate in a default mode if the power mode serial data message does not match what the individual
module can see from its own connections.
The power mode master receives ignition switch signals to identify the operators desired power mode. The Power Mode Parameter tables below illustrate the correct state of these input parameters (circuits) in correspondence to
the ignition switch position:
Ignition Switch Position Power Mode Ign. Off/Run/Crank Ignition Accessory/Run Ignition Run/Crank
Transmitted (Off/Run Crank Voltage (Accessory Voltage (Ignition 1 Voltage
Circuit) Circuit) Circuit)
• Headlamps ON
• Key-in-ignition
• Ignition ON
• Park lamps ON
The BCM will enter a sleep state when all of the following conditions exist:
If all these conditions are met, the BCM will enter a low power or sleep condition.
S38 K84
Ignition Keyless
Mode Entry
Switch Control
Module
K9
Body
Control
Module
KR75
Engine Controls
Ignition Relay
Power to many of this vehicles circuits is controlled by the module that is designated the power mode master. This vehicles power mode master is the body control module (BCM). The BCM has multiple B+ circuits that feed into
it. Each of those circuits are partitioned within the controller to drive certain outputs of the vehicle’s body functions. An open or short in any one of the B+ circuits may induce multiple codes/or a section of non-functionality
within the BCM with the rest of the BCM functioning normally. In this case it is useful to refer to the power distribution schematics to determine if the non-functional partition of the controller shares a common B+ circuit. The
ignition mode switch is a low current switch with a discrete ignition signal to the power mode master for determination of the power mode that will be sent over the serial data circuits to the other modules that need this
information. The power mode master will also activate relays and other direct outputs of the power mode master as needed. The power mode master determines which power mode (OFF, Accessory, Run, Crank Request) is
required, and reports this information to other modules via serial data. Modules which have switched voltage inputs may operate in a default mode if the power mode serial data message does not match what the individual
module can see from its own connections.
The keyless entry control module also monitors voltage on the switch in the same manner as the BCM, but monitors the second switch located in the ignition mode switch. The keyless entry control module also controls the
backup power through the run/crank coil control circuit by applying voltage to the ignition voltage circuit. This circuit is a pass-thru in the BCM and will energize the ignition circuit when the appropriate power mode is required.
The power mode master receives ignition switch or ignition mode switch signals to identify the operators desired power mode. The Power Mode Parameter tables below illustrate the correct state of these input parameters
(circuits) in correspondence to the ignition switch position or ignition mode switch with the transmitter to vehicle range:
Power Mode Power Mode Transmitted Push Button Ignition Push Button Ignition Key in Cylinder
Switch Switch Voltage Switch/Key Fob in
(Power Button Switch Push Button Ignition Vehicle
Circuit Input to the BCM) Switch Voltage Input to (Transmitter in Range to
the BCM the BCM Signal)
Vehicle On Power Mode, OFF Active (pushed) / Inactive 5-6 V (pressed) Yes
then Press the Power (not pushed)
Button Switch (Foot on or
OFF the Brake Pedal)
Transmitter in Vehicle
Vehicle OFF Power Mode, Accessory Mode Active (pushed) / Inactive 5-6 V (pressed) Yes
then Press the Power (not pushed)
Button Switch with foot
OFF the Brake Pedal;
Transmitter in Vehicle
Vehicle OFF Power Mode, Vehicle in Run/Start Mode Active (pushed) / Inactive 5-6 V (pressed) Yes
then Press the Power (Ignition ON engine (not pushed)
Button Switch with foot on running.)
the Brake Pedal;
Transmitter in Vehicle
Vehicle OFF Power Mode, Vehicle in Run/Start Mode Active (pushed) / Inactive 5-6 V (pressed) Yes
then Press and Hold the (Ignition ON without the (not pushed)
Power Button Switch for engine running)
5 s with foot OFF the
Brake Pedal; Transmitter
in Vehicle
Vehicle OFF Power Mode, Vehicle In Service Mode Active (pushed) / Inactive 5-6 V (pressed) Yes
then Press and Hold the (Ignition ON without the (not pushed)
Power Button Switch for engine running)
10 s with foot OFF the
Brake Pedal; Transmitter
in Vehicle
• Headlamps ON
• Key-in-ignition
• Ignition ON
• Park lamps ON
The BCM will enter a sleep state when all of the following conditions exist:
If all these conditions are met, the BCM will enter a low power or sleep condition.
K9 K84
Body Keyless
Control Entry
Module Control
Module
The body control module (BCM) monitors the ignition position, battery condition, and each door ajar/open switch status to determine whether the retained accessory power should be initiated or terminated. Retained accessory
power is controlled by two different methods; retained accessory power relay coil control circuit and serial data. Some modules receive a retained accessory power message from the BCM over the serial data circuits. Serial data
controlled retained accessory power is deactivated as required by their modules retained accessory power mode operation. Other subsystems may be activated directly by the BCM or by the BCM through a relay. Components
and systems that are active in retained accessory power are also activated anytime the ignition is any position other than OFF regardless of the door switch signals.
• The BCM receives an input from any door ajar or open switch indicating the opening of any door after the ignition key is out of the ignition.
Note: If the BCM is receiving any door ajar or open signal from those switches when the ignition key is turned OFF, retained accessory power will not initiate.
• The BCM internal timer for the retained accessory power expires after approximately 10 min.
Systems powered by the retained accessory power relay coil control circuit during the retained accessory power mode are as follows:
Note: The vehicle may not be equipped with all components as listed below.
• Sunroof Switch
• Transmission Shift Lever Position Indicator (w/floor mounted console gear shift)
Radio
Radio retained accessory power activation/termination is the same as relay operation with one exception; the only door switch that will turn off the radio during retained accessory power is the driver door open switch.
A11 K73
Radio Telematics
Communication
Interface
Control Module
K9
Body
Control
Module
KR76A KR76B
Retained Retained
Accessory Accessory
Power Power
Relay 1 Relay 2
The body control module (BCM) monitors the ignition switch position, battery condition, and each door ajar/open switch status to determine whether the retained accessory power should be initiated or terminated. Retained
accessory power is controlled by two different methods; relay control and serial data. Some modules receive a retained accessory power message from the BCM over the serial data circuits. Serial data controlled retained
accessory power is deactivated as required by their modules retained accessory power mode operation. Other subsystems are activated directly by the BCM through a relay. Components and systems that are active in retained
accessory power are also activated anytime the ignition is any position other than OFF regardless of the door switch signals.
• The BCM receives an input from any door ajar or open switch indicating the opening of any door after the ignition key is out of the ignition.
Note: If the BCM is receiving any door ajar or open signal from those switches when the ignition key is turned OFF, retained accessory power will not initiate.
• The BCM internal timer for the retained accessory power expires after approximately 10 minutes.
Systems powered by the retained accessory power relay 1 and retained accessory power relay 2 during the retained accessory power mode are as follows:
Note: The vehicle may not be equipped with all components as listed below.
• Sunroof Switch
L
B+ B+ O
C
X51R A11 P16 X51R
Fuse Block - A90 Radio P9 Instrument Fuse Block -
Instrument Logic Cluster Instrument D
F28DR Driver Information F20DR E
Panel Right Center Display 10A Panel Right S
10A C
A90
Logic X2 1
X1 43
X5 45 X88/Z88 Z75-UGN
J403 X61A J212
Junction
Block -
Instrument Interior Lights Interior Lights
Panel Dimming Dimming
X1 11 Schematics Schematics
X1 1 4 8
K182
B+ Parking
Assist 3 5 3 10 8
Control S48A S48D
Module Multifunction Multifunction
Switch - Switch 2 -
Instrument Instrument
Panel Panel
A90
B+ Logic
8 4
X1 7 3
5852 9 5
GN/BN
2751 1850 1850
BK/WH X1 45 BK BK
X61A
Junction
Block -
Instrument X88/Z88 Z75-UGN
Panel
X5 26
L
O
C
K182
Parking
Assist D
E
Control S
Module C
12V
X2 6 4 1 3 7 5 8 2
X495 7 1 2 3 5 4 6 21
J490
3 1 2 3 1 2 3 1 2
B306E B306G B306N
Parking Assist Parking Assist Parking Assist
Sensor - Rear Sensor - Rear Sensor - Side
Left Outer Right Middle Right Rear
3 3 3
UKG UKG
L
O
C
D
E
S
C
K182
Parking
Assist
Control
Module
12V
X3 3 1 4 5 12 11 8 10
X150 25 27 32 29 31 30 26 28
X100 20 4 5 6 10 7 11 22
J105
3 3 3
1 2 1 2 1 2
B306K B306B B306D
Parking Assist Parking Assist Parking Assist
Sensor - Side Sensor - Front Sensor - Front
Left Front Left Middle Right Outer
3 3 3
UKG UKG
5214 5214 5214 5214 5214 5214
BK/BU BK/BU BK/BU BK/BU BK/BU BK/BU
J107
X51L X50A L
Fuse Block Fuse Block - K188
Human O
KR73 - Instrument Underhood C
Ignition Panel Left KR61 Machine
Main Trailer Backup Interface
Relay Lamps Relay Control D
Module E
Bypass S
F36DL F34UA C
Module
10A 10A
W7
5 6 Blunt Cut -
X1 32 X4 A3 Shield
J386
X275 8 9 29
6974
BARE
X900 4 2 3 8 6
6972 6973 6974
GY/YE WH/BU BU/YE
9
1739 24
RD WH
6974
BARE
6 3 1 4 2
B87
IGN R Rearview
Camera
5
2550
BK
G325
B+ X50A L
Fuse Block - O
X51L Underhood C
KR61
Fuse Block
Trailer Backup
- Instrument
Lamps Relay D
Panel Left E
S
C
F39DL F34UA
10A 10A
X4 A3
X2 35
24
L-GN/WH
J386
2840
RD/GY
Data 24
Power Communication L-GN/WH
Moding Schematics
J220 Schematics
X275
X275 10
2840 755 7527
RD/GY GY/VT GN/WH 5 6
24
L-GN/WH
6972 6973
GY/YE YE/BU
9
X1 1 2 3 9 6 18
K188
B+ IGN R Human
Machine
Interface
Control
Module
Bypass
X1 19 8 20 5 Module
6972 6973
6974 GY/YE WH/BU
BARE
9
X2 5 6
6974
BARE
2550
BK
W7 K74
Blunt Cut - Human
Shield Machine
Interface
Control
Module
G325
L
O
C
D
E
S
C
B87
Rearview
Camera
D
X2 BU
COAX
X424 WH
COAX
-SWB SWB
X423 GY X354 YE
COAX
X353 GY COAX
COAX
X2 GY
A10
D Inside
Rearview
Mirror
B+ L
O
C
X51R
Fuse Block -
Instrument D
F28DR Panel Right Data E
10A Communication S
Schematics C
3140 5060
X1 43 RD/GN GN
3140 J498
RD/GN
J403 X495 17
3140
RD/GN 3140 3140
RD/GN 5060 RD/GN
GN
3140
RD/GN 8 1 8
B218L B218R
B+ Side Object B+ Side Object
X495 22
Sensor Sensor
Module - Module -
3140 Left Right
RD/GN
7 4 5 4 5 7 2 1
1450 3812 3810 3812 3810 1450 5853 5861
BK BU/WH BU/YE BU/WH BU/YE BK GY/YE GY
9 9
X495 15 16
5853 5861
GY/YE GY
X500 37 X600 37
5853 5861
GY/YE GY
X510 15 X610 15
5853 5861
BK/YE BK/YE
A9A A9B
X525 6 Outside X625 4 Outside
Rearview Rearview
5853 Mirror - 5861 Mirror -
BK/YE Driver BK/YE Passenger
X3 1 X3 1
E17D E17P
Outside Outside
Rearview Rearview
Mirror Mirror
Glass - Glass -
Driver Passenger
X3 2 X3 2
1150 1250
BK BK
X525 5 X625 3
1150 1250
BK BK
F19DL K9 L
F38DR Body B+ B+ O
Control C
Module X51R X51R
Fuse Block - Fuse Block -
Instrument Instrument D
X4 23 F28DR F20DR E
Panel Right 10A Panel Right S
10A C
5986
WH/BU
X2 1
J365 X1 43
3140
RD/GN
5986
WH/BU
J403 1540
X275 23 RD/GN
3153
GY/WH
5986
WH/BU 3140 X88/Z88 Z75-UGN
RD/GN
J260
X2 5 X4 11 J212
X61A Interior Lights Interior Lights
5986 Junction Dimming Dimming
WH/BU Block - Schematics Schematics
Instrument
Panel
X3 3 45
X203 6
9 3 10 10 5 3 6 8
B174W S48A S48D
IGN B+ Frontview Multifunction Multifunction
Camera - (UFL) Switch - (UFL) Switch 2 -
Windshield Instrument Instrument
Panel Panel
(UHX) (UHX)
A90
B+ Logic
1 11 6 5 4 8 6
3152
WH
G210 G218 G218
X51L L
O
Fuse Block C
KR73 - Instrument
Ignition Panel Left
Main D
Relay E
S
C
F25DL K9
10A Body
A11 F19DL
F38DR Control
Radio Module
X2 28
X3 4 16
1 X1 6 4
P43 X85
IGN Collision Alert Steering
Indicators Wheel Air
Bag Coil
X2 5 7
4 3 2 5737
GY/OG (X88/Z88)
1444 5737
3535 3885 WH GY/GN (Z75)
WH/GN GY/YE
1102 3894 3894
GY/GN GN/BK GN/BK
8 9 (Z75)
X1 30 12 3 20 21 9 3 (-Z75)
P16 S70L
Instrument Steering
Cluster Wheel
Controls
Switch -
Left
1851
BK/WH
A90
Logic
G218
B+ B+ L
O
C
X51R K9 A11 P16 X51R
Fuse Block - Body Radio P9 Instrument Fuse Block -
Instrument Control Driver Information Cluster F20DR Instrument D
F28DR Panel Right Module Center Display Panel Right E
10A 10A S
C
X4 23
A90
Logic X2 1
X1 43
3140 5986 1540
RD/GN WH/BU RD/GN
J403 J365 J212
X1 1 12 X2 7
K124
B+ IGN Active
Safety
Control
Module
X1 8 X2 16 X1 3 2 11
X2 5 X2 43 49 X1 45 11
X61A X61A
Junction Junction
Block - Block -
Instrument Instrument
Panel Panel
X3 3 X4 11 26 X5 26 45
Interior Lights
Dimming
Schematics
2 6 2 3 9 10 8
B174W S48D
B+ Frontview Multifunction
Camera - Switch 2 -
Windshield Instrument
Panel
5 A90
B+ Logic
L
O
C
D
E
S
C
K124
Active
Safety
Control
Module
X1 9 10 6 7 13 14 12 X2 3 4 6 11 12 14 1 2 9 10 7
3808 3809 3935 3935 3936 3936 5986 3813 3813 3813 3811 3811 3811 6105 6105 6106 6106 5060
GY/VT BN/VT BU/GY BU/GY WH/GY WH/GY WH/BU BU/VT BU/VT BU/VT WH WH WH BU/YE BU/YE WH WH GN
3808 3813 3811 3813 3811 3808 3811 3813 3811 3813 3811 3813
GY/VT BU/VT WH BU/VT WH GY/VT WH BU/VT WH BU/VT WH BU/VT
10 3 4 8 9 6 2 3 4 5 10 11
B174W B233B
IGN Frontview IGN Radar
Camera - Sensor
Windshield Module -
Long
Range
7
250
BK
G102
L
O
C
D
E
S
C
K124
Active
Safety
Control
Module
3808 3811 3813 3811 3813 3808 3811 3813 3811 3813
GY/VT WH BU/VT WH BU/VT GY/VT WH BU/VT WH BU/VT
5 1 2 6 7 5 1 2 6 7
B233LF B233RF
IGN Radar IGN Radar
Sensor Sensor
Module - Module -
Short Short
Range Range
8 4 Left Front 8 3 Right Front
G102
L
O
C
D
E
S
C
K124
Active
Safety
Control
Module
3809 3811 3813 3811 3813 3809 3811 3813 3811 3813
BN/VT WH BU/VT WH BU/VT BN/VT WH BU/VT WH BU/VT
5 1 2 6 7 5 1 2 6 7
B233LR B233RR
IGN Radar IGN Radar
Sensor Sensor
Module - Module -
Short Short
Range Range
8 Left Rear 8 3 4 Right Rear
G402
L
O
B+ B+ C
X51L
Fuse Block D
- Instrument E
S
F44DL F27DL Panel Left K182 B174W K124 C
30A 10A Parking Frontview Active
Assist Camera - Safety
Control Windshield Control
Module Module
X1 27 5
5040 1140
RD/YE RD/BN
UD5/UD7 UGN
X310 2 23
X1 2 1 X2 1
K40D
B+ B+ Seat
Memory
Control
Module -
X2 5 X5 5 4 Driver
3037 3038
YE/BN BN
1 1
P45LR P45RR
M Seat M Seat
Haptic Haptic
Movement Movement
Motor - Motor -
Driver Left Driver
2 Rear 2 Right Rear
1150 1150
BK BK
G311
X51L L
O
KR73 Fuse Block C
Ignition - Instrument
Main Panel Left
Relay D
E
S
C
F17DL
10A
Data
Communication
Schematics
X1 3
1640 1102
RD/VT GY/GN
X2 1 3
K157
IGN Video
Processing
Control
Module
X2 7 6 12 11
9 6974
BARE
X275 8 9 29
9 6974
BARE
2550
BK
X2 5 6
K74
Human W7
Machine Blunt Cut -
Interface Shield
Control
Module
G325
L
B174G B87 O
C
Frontview Rearview
Camera - Camera
Grille D
E
S
C
6V 6V
5 4 1 3 2
6201 2551 7641 7642 6799
6201 2551 3373 3372 3371 WH/BN BK/WH BU WH BK
WH/BN BK/WH BU GY BK
6 5 1 4 2
9 3371
BARE
6201 2551 7641 7642 6799
VT/GN BK/WH GY/YE WH/BU BK
X100 31 27 29 30 28
9 6799
BARE
9 3371
BARE
X150 1 2 3 4 7 X900 32 20 34 33 35
6201 2551 3373 3372 3371 6201 2551 7641 7642 6799
WH/BN BK/WH BU GY BK WH/BN BK/WH BU WH BK
9 3371 9 6799
BARE BARE
W7 W7
Blunt Cut - Shield Blunt Cut - Shield
X1 12 2 1 11 13 3 4 14
K157
Video
Processing
Control
Module
B225L B225R L
Sideview Sideview O
Camera - Camera - C
6V Left 6V Right
D
E
S
6201 2551 2628 2625 2624 6201 2551 2627 2626 2623 C
PK BK RD L-BU WH PK BK RD L-BU WH
6 5 1 4 2 6 5 1 4 2
6201 2551 2628 2625 2624 6201 2551 2627 2626 2623
WH/BN BK/WH WH/GN GY/GN BK WH/BN BK/WH BN/YE GY/BU BK
9 2624 9 2623
BARE BARE
X515 6 5 1 4 2 X615 6 5 4 1 2
6201 2551 2628 2625 2624 6201 2551 2627 2626 2623
WH/BN BK/WH WH/GN GY/GN BK WH/BN BK/WH BN/YE GY/BU BK
9 2624 9 2623
BARE BARE
X500 11 4 12 13 26 X600 35 40 12 13 26
6201 2551 2628 2625 2624 6201 2551 2627 2626 2623
WH/BN BK/WH WH/GN GY/GN BK WH/BN BK/WH BN/YE GY/BU BK
2624 2623
9 9
BARE BARE
W7 W7
Blunt Cut - Shield Blunt Cut - Shield
X1 16 6 5 15 17 7 8 18
K157
Video
Processing
Control
Module
The adaptive cruise control functionality depends on various modules on the vehicle to function and each module performs a function that is critical to the proper operation of the adaptive cruise control system. Adaptive cruise
control will not operate if any components fail. Communication between modules is via serial data. The following is a functional description of the active safety control module and the other associated components:
• Instrument cluster
• Gap switch
• The active safety control module processes the road environment to get data concerning any vehicle ahead of the adaptive cruise control vehicle. Detection, parameter estimation, tracking, object classification and
diagnostics are the primary functions. When an object is detected, the controller calculates the object range, range rate, acceleration and azimuth angle parameters.
• The active safety control module performs adaptive cruise control state processing automatically – distance control or speed control. The adaptive cruise control operates in 2 possible states – cruise or follow. The normal
operating state is cruise, whereby the vehicle speed is controlled to match the driver selected set speed. When a preceding forward target is identified, the adaptive cruise control system will automatically transition into
the follow speed state to provide proper lane spacing behind the target vehicle in front. The preceding vehicle's speed and acceleration, with the adaptive cruise control vehicle speed, acceleration and distance between
the two vehicles will be used to determine the adaptive cruise control follow speed limit. The adaptive cruise control follow speed limit will ensure that an acceptable distance is maintained to the preceding vehicle.
• The active safety control module determines the follow speed limit for throttle control by the ECM.
• The active safety control module arbitrates the adaptive cruise control system brake and throttle control between the EBCM and the ECM.
• The active safety control module requests brake light activation during automatic braking.
• The active safety control module provides operational feedback to the vehicle driver. The active safety control module sends signals for telltales and messages to be displayed on the instrument cluster or driver
information center.
• The BCM provides a translating gateway for the high speed GMLAN serial data circuit.
• The BCM reads all cruise control switches and the gap switch. The active safety control module monitors a variety of user operated switches from the BCM switch status information sent via the GMLAN serial data
circuit.
• The BCM illuminates the brake light based on a GMLAN message from the active safety control module during automatic braking.
• The BCM measures the brake pedal position and sends brake pedal travel status via GMLAN serial data circuit to the ECM. The ECM disengages the adaptive cruise control system when the brake is applied by the driver
pressing the brake pedal.
• The BCM serves as a gateway to the instrument cluster and driver information center. The BCM will generate visual warnings based on high speed GMLAN serial data messages from the active safety control module.
• The ECM provides the electronic throttle control to the adaptive cruise control System. The ECM is also responsible for determining when a driver is overriding the adaptive cruise control throttle position by pressing the
accelerator pedal.
• The ECM processes the cruise control switch requests received via the GMLAN serial data circuit from the BCM. Engaging and disengaging the adaptive cruise control system are functions performed by the ECM.
• The ECM allows automatic braking without disengaging the adaptive cruise control.
• The EBCM provides automatic braking for the adaptive cruise control system. The active safety control module will request vehicle deceleration via high speed GMLAN serial data circuit.
• The EBCM determines when the driver–applied brake pressure is active. The EBCM will communicate this status via the GMLAN serial data circuit to the BCM.
• The EBCM releases vehicle automatic braking when there is a throttle override by the driver pressing the accelerator.
• The EBCM predicts brake temperatures. Due to automatic braking, the brake system may overheat. When the brakes are overheated, the EBCM requests the adaptive cruise control System to be temporarily shut down
by the ECM until the brakes cool to a normal operating temperature.
Instrument Cluster
The driver information center is a part of the instrument cluster and displays the adaptive cruise control system warning messages. The active safety control module requests messages to be displayed on the driver information
center by sending a GMLAN request to the BCM. The BCM sends a GMLAN serial data request to the instrument cluster demanding the display of the warning message. When the message is acknowledged by the driver and the
cause of the message resolved, the driver information center turns the message off. The adaptive cruise control system will not operate if the driver information center fails.
• On/Off switch
• Set/decrease switch
• Resume/increase switch
The cruise control function switches are arranged in a resistive ladder design whereby each switch function is set up with different resistance values. The BCM through the cruise control switch signal circuit detects a
predetermined voltage value when any cruise control switch function is activated. The associated cruise control function signal detected by the BCM is then sent to the engine control module (ECM) as a GMLAN serial data
circuit message. The ECM on receiving the message provides the cruise control function requested by the BCM. The ECM is responsible for recognizing and responding to cruise control switch requests sent by the BCM. The
cruise control function switches are used by the ECM to communicate to the active safety control module the driver selected vehicle speed. The driver selected vehicle speed is communicated through GMLAN serial data circuit
to the active safety control module and the BCM. The adaptive cruise control system engages and adjusts vehicle speeds based on the activation of the following cruise control function switches:
Gap Switch
The gap switch allows the driver to determine how closely the adaptive cruise control vehicle follows a target vehicle while adaptive cruise control is engaged. When the adaptive cruise control vehicle speed is being limited due to
a slower travelling vehicle, the adaptive cruise control vehicle speed is automatically controlled to the follow speed limit. The gap switch has 3 following distance selections that range from 1–2 s. The gap switch following
distance between the adaptive cruise control vehicle and the target vehicle is expressed in time as opposed to actual distance. The distance maintained for a selected gap will vary based on vehicle speed. The faster the vehicle
speed, the further back you will follow. The gap setting can only be adjusted when the adaptive cruise control system is engaged. The gap switch is hard-wired to the BCM. Based on voltage variations, the BCM is able to read
the gap switch selection and communicates the switch status on the GMLAN serial data circuit to the active safety control module. The gap switch is a momentary switch.
The initial push of the gap switch recalls the current setting and activates the display. Subsequent pushes of the gap switch will change the gap setting.
Set Speed
The adaptive cruise control vehicle set speed is displayed at all times in the driver information center when adaptive cruise control is engaged. The active safety control module set speed display request is sent to the instrument
cluster via the GMLAN serial data circuit.
Follow Distance
The driver information center displays the driver selected following distance when adaptive cruise control is engaged and the gap switch is active. The current follow distance setting is displayed in the driver information center for
a few seconds after the gap switch is pressed to increase or decrease the following distance. The active safety control module follow distance display request is sent to the instrument cluster via the GMLAN serial data circuit.
When the transmission is placed into R, 12 V is applied to the reverse lamp control circuit by the body control module (BCM). The rearview camera monitors this circuit and when 12 V is seen, indicating that the transmission is in
R, the rearview camera will activate. The rearview camera receives ignition voltage and a constant ground to power the camera. Video signal + and video signal – circuits carry the video image from the rearview camera to the
infotainment system. Additionally, the video signal circuits are shielded to prevent any interference which may lead to a loss of video signal resolution and cause a degraded video image. The shield is grounded by the rearview
camera.
The following conditions may cause a degraded rear vision camera image:
• Dark conditions
• Extreme light conditions, such as glare from the sun or the headlights of another vehicle
When the vehicle is traveling at speeds slower than 6 mph (10kph) the video processing control module will power up the cameras and send a video signal to the radio or human machine interface module.
The following conditions may cause a degraded surround vision camera image:
• Dark conditions
• Extreme light conditions, such as glare from the sun or the headlights of another vehicle
Surround Vision displays an overhead view of the area surrounding the vehicle, along with the front or rear camera views in the center stack. The front camera is in the grille or near the front emblem, the side cameras are on the
bottom of the outside rearview mirrors, and the rear vision camera is above the license plate.
• Rear camera (B87 Rearview Camera) view alongside overhead view is displayed in reverse
• Front camera (B174G Frontview Camera – Grille) view alongside overhead view is displayed after shifting out of reverse to Neutral or Drive
• Will display front view when front park assist object is within trigger range calibration value (30 cm (12 in) in a forward gear
• Image is removed from display when vehicle speed exceeds speed calibration (10kph/6 mph) or button press / screen touch
System Operation
The video processing control module sends voltage and a constant ground to power the cameras. Video signal + and video signal – circuits carry the video image from the cameras to the video processing control module for
processing. The video processing control module will then send the processed image output to infotainment system by Video signal + and video signal – circuits. Additionally, all the video signal circuits are twisted and shielded
to prevent any interference which may lead to a loss of video signal resolution and cause a degraded video image. These circuits must not be spliced/removed from shielding or will cause image degradation.
The video processing control module receives CAN information from Rear Park Assist object detection module and Steering Wheel angle from body control module during Reverse. A warning triangle may display during the 360
surround view screen if Rear Parking Assist has detected an object during a reverse. This triangle changes from amber to red and increases in size the closer the object. Also a dynamic guideline is displayed in Reverse to show
the projected path of the vehicle.
L
O
C
T4M D
Radio E
S
Antenna C
6002
WH
K9 T23
Body RFR Radio
Control Antenna
12V Module Amplifier
RFR
X2 25 27 16 X1 26 X4 OG
X225 5 26 27 6
COAX
X1 4 2 1 3 X2 OG
K77
12V Remote
Control Door
Lock Receiver
RFR
B+ A24D A24P L
T10M Door T10N Door T10G O
Keyless Entry Handle Keyless Entry Handle Keyless C
X51L
Fuse Block Antenna - Driver Assembly - Antenna - Assembly - Entry
- Instrument Door Handle Driver Passenger Door Passenger Antenna -
F28DL Exterior Exterior D
Panel Left Handle Rear E
10A S
1 2 Fascia
C
9 9
Data
Communication
Schematics 3560 3561 3562 3563 3568 3569
VT VT/GY GN/YE GN/BK BN/GN GN/GY
9 9 9
X500 28 27 X600 28 27
X1 2 3 X2 6 7 20 9 16 18
K84
B+ Keyless
Entry
Control
Module
X1 14 16 17 20 15 18 19
3554 3555
BU GY/BK
2751 3552 3553 9 3556 3557
BK BN/BK WH WH/GN GN
9 9
X275 27 28
3552 3553
BN/BK WH X300 12 33
9
3554 3555
BU GY/BK
9
1 2 1 2 1 2
T10J T10K T10E
Keyless Entry Keyless Entry Keyless Entry
Antenna - Center Antenna - Center Antenna -
Console Front Console Rear Rear
Compartment
G327
L
O
C
B+
X51L D
E
Fuse Block S
- Instrument C
F7DL
10A Panel Left
X3 12
240
RD/YE
X316 17
Interior Lights
Dimming
Schematics
240 6817
RD/YE YE
1 2
S25
Garage
Door
Opener
A90
B+ RD Logic
1050
BK
G210
K84
Keyless
Entry
Control
Module
K77
Remote
Control
Door Lock
Receiver
• Door lock/unlock
• Automatic window express down, if equipped. Automatic window express up, if equipped
• Driver and front passenger door antennas (part of the door handle assembly)
• Driver and front passenger door handle switches (part of the door handle assembly)
Door Antennas
The keyless entry door antennas are used to transmit low frequency communications to the keyless entry transmitters.
The keyless entry door antennas are located in the left front and right front exterior door handle bracket. The antennas are serviced as part of the door handle assembly. The antennas are controlled by the keyless entry control
module. When the exterior door handle button is pressed, the respective antenna will send out a challenge to the keyless entry transmitter, which begins the passive entry communications.
• Backup control for the ECM accessory wakeup and the run/crank relay
• Receiver of the exterior door handle switch inputs and door open switch (not the door ajar switch)
• Receive and authenticate active transmitter and keyless start signals from the remote control door lock receiver
• Illuminate the interior lamps for a determined length of time, or until the ignition is turned ON
When all doors are closed, they can also be locked from the exterior by pressing a front door handle button while having a valid transmitter within range.
If more than one keyless entry transmitter is within a vehicle and the Keyless Entry System detects that one or more transmitters have been left in the vehicle after vehicle is locked, any transmitter left within the vehicle will be
temporarily deactivated until:
• A button on the deactivated key fob is pressed (will only activate the fob whose button is pressed)
A press and hold of the panic button performs the following functions:
• Pulses the horn and flashes the parking lamps for 30 second or until the following conditions occur:
When the BCM determines all conditions meet those required for a remote vehicle start event, a message is sent via serial data to the ECM. The ECM relies on the remote vehicle start message from the BCM to enable remote
vehicle start when the crank request signal is received. If the ECM does not receive a valid remote vehicle start message, it will not ground the control circuit of the crank relay and start the engine. While the ECM is in remote
vehicle start mode it will cut fuel to the engine if any of the following additional conditions occur:
• Transmission is not in P