REFERENCE ONLY

Correcting Erroneous Software Load on Citation 680A

Garmin G5000 Software Version 45
If Files Were Loaded Using SYSTEM UPLOAD PAGE

Caution: Before starting the software or configuration loading process, certain

items may be required to be recorded first, to prevent loss of
information or settings. See Section 1 for details.

Caution: Make certain that all SD cards are available before starting. These are
usually located in a blue pouch onboard the aircraft (usually in AFM).

Caution: Ensure that power is available through a GPU so that power is not
interrupted during the loading process. Plug the main ships batteries
in for a buffer in case power is lost from the GPU.

Note: This document is to supplement, not replace, the Cessna Citation

680A MM, and Garmin G5000 LMM.

Note: Reference latest revision of the Garmin G5000 LMM 190-01595-00.

Table of Contents

Introduction G5000 System Familiarization

Section 1 Reasons to Use This Document
Section 2 Determine Settings & Options Currently Installed
Section 3 Software and Configuration Loading
Section 4 Reinstalling Options
Section 5 CMC Diagnostic Configuration Upload Loading
Section 6 PERF & TOLD Databases
Section 7 Transaction Log
Section 8 Aircraft Configuration
Section 9 Final Verification / Return to Service

1
Version 1.0 REFERENCE ONLY
 REFERENCE ONLY
Introduction G5000 System Familiarization

When in configuration mode, select GDU controls on left side of the GTC. Ensure that PFD 1 is
selected on the screen. The dual concentric knobs on the lower right bezel will be utilized, and
throughout this document will be referred to as the FMS small and large knob. The Enter
button will be in the lower right part of the screen.

The displays can be individually powered down by turning the outer knob of the respective
dimming knob to the left to shut off the display unit. Locations are shown in the above image.
An alternative is to pull the respective circuit breakers shown below.
• PFD 1
o L PFD (Left CB Panel - O4) & L PFD AUX (Left CB Panel - L4)
• MFD
o MFD (Right CB Panel – DD2) & MFD AUX (Right CB Panel – HH4)
• PFD 2
o R PFD (Right CB Panel – JJ4)
2
Version 1.0 REFERENCE ONLY
 REFERENCE ONLY
Section 1 Reasons to Use This Document

• With the introduction of the -40 software load in the Latitude, the Intelligent LRU
loading procedure was introduced. This is continued in the -45 software load.
o It is vital that technicians use the LRU replacement page for loading software and
configurations to LRUs after swapping or replacing.
o Instructions are in the maintenance manual in section 34-60-03 “GARMIN G5000
INTEGRATED AVIONICS SYSTEM LRU/OPTION SOFTWARE VERSION 45
CONFIGURATION – ADJUSTMENT/TEST”.
• If software and/or configurations were loaded for an LRU using the SYSTEM UPLOAD
page, then a complete configuration load is required.
o The instructions provided in this document are to assist the technician in resetting
the software and configuration correctly for the system to function correctly.
• The instructions include:
o How to determine what options are installed for reinstallation later.
o Performing a complete configuration load.
o Reinstall options.
o Performing PERF and TOLD loading.
o Performing CMC diagnostic configuration loading.
o Performing Aircraft Configuration loading.
o Final Verification / Return to Service

3
Version 1.0 REFERENCE ONLY
 REFERENCE ONLY
Section 2 Determine Settings & Options Currently Installed

Note: This is with the G5000 powered up in normal mode.

Recording Empty Weight Value

1) Select Home.
 Select PERF.
 Select Weight and Fuel.
 Record the Basic Empty Weight= ___________
 Record the Pilot(s) & Stores= ____________
• This will need to be entered back in after the configurations are loaded.
Saving Crew Profiles
1) First it is necessary to save any customer crew profiles to prevent loss of the settings.
 From the Home screen on the GTC570, select Utilities.
 Select Crew Profile.
 If there are any profiles besides the Default, then they need to be exported to the
Crew Profile SD card.

Note: The Default crew profile is already on the Crew Profile SD card, and does
not need to be exported. If it is the only profile, then no other steps in this
section is necessary.

2) Rotate the dimmer knob off for the MFD.

3) Remove the 8945503-13 Diagnostics SD card from the upper slot of the MFD.
4) Insert the 8431108-9 Crew Profile SD card into the upper slot of the MFD.
5) Rotate the dimmer knob on for the MFD.
6) The crew profiles need to be exported to the SD card:
 From the Home screen on the GTC570, select Utilities.
 Select Crew Profile.
 Select the first saved crew profile.
 Select Export.
7) Repeat step 6 for any other saved crew profiles.
8) These will be reinstalled later to reload the customer’s preferences.
9) Remove the 8431108-9 Crew Profile SD card from the upper slot of the MFD.

4
Version 1.0 REFERENCE ONLY
 REFERENCE ONLY
Determine Options Installed
Note: This is with the G5000 powered up in configuration mode.
• Setting the G5000 up in configuration mode:
1) Pull the following circuit breakers:
 L PFD GTC (Left CB Panel - E4)
 MFD L GTC (Left CB Panel - N3)
 MFD R GTC (Right CB Panel – MM4)
 R PFD GTC (Right CB Panel – NN4)
2) Turn the dimmer knob to off for PFD 1, MFD, and PFD 2.
3) Insert the 010-01273-26 software loader card into the upper slot of PFD 2.
4) Turn aircraft and avionics power on.
5) Press and hold the right knob on the left PFD GTC and push the L PFD GTC circuit
breaker (E4) in.
 Let go when you see initializing.
6) Press and hold the right knob on the left MFD GTC and push the MFD L GTC circuit
breaker (N3) in.
 Let go when you see initializing.
7) Press and hold the right knob on the right MFD GTC and push the MFD R GTC
circuit breaker (MM4) in.
 Let go when you see initializing.
8) Press and hold the right knob on the right PFD GTC and push the R PFD GTC circuit
breaker (NN4) in.
 Let go when you see initializing.
9) Turn the R PFD dimming knob on to power the display.
 It will load files from the card.
 PFD 2 should come up in configuration mode.
• SYSTEM STATUS should show at the top of the screen.
• Pull the 010-01273-26 software loader card from the upper slot of
PFD 2.
10) Insert the 010-01273-26 software loader card into the upper slot of the MFD.
11) Turn the MFD dimming knob on to power the display.
 It will load files from the card.
 MFD should come up in configuration mode.
• SYSTEM STATUS should show at the top of the screen.
• Pull the 010-01273-26 software loader card from the upper slot of
the MFD.
12) Insert the 010-01273-26 software loader card into the upper slot of PFD 1.

5
Version 1.0 REFERENCE ONLY
 REFERENCE ONLY
13) Turn the L PFD dimming knob on to power the display.
 It will load files from the card.
 PFD 1 should come up in configuration mode.
 SYSTEM UPLOAD should show at the top of the screen.
14) Select GDU Controls on the GTC.
15) Rotate the small FMS knob to the right and select TRANSACTION LOG page.
16) A list of current files loaded to the system will be shown. See image below.
 The most recent files are at the top of the list.
 It will potentially show:
• CMC Configuration
• Options from unlock SD cards
• Options from Software Loader SD card
• Base Load
17) Record the options noted on the Transaction Log in Table 1

6
Version 1.0 REFERENCE ONLY
 REFERENCE ONLY
Option Description YES NO
FK629S - Stormscope
FK632A – VHF Datalink (Datalink/COMM 3)
FK632B – Single HF (Full UP)
FK632D – Second HF (Full Up)
FK632L – Sirius XM
FK658A – ADF
FK658E – ADF2
FK676A – Iridium Voice/Datalink
FK676N – Iridium Datalink
* ACARS Unlock ARINC Direct
* ACARS Unlock Honeywell GDC
* ACARS Unlock Universal
SurfaceWatch Unlock
VHF Datalink (CPDLC – Link 2000+) Unlock
Steep Approach Unlock
FANS-1/A Unlock

TABLE 1

* These 3 options utilize the same SD card. There can only be one of the 3 options installed.

7
Version 1.0 REFERENCE ONLY
 REFERENCE ONLY
Section 3 Software and Configuration Loading

This section will provide the steps necessary to correct the configurations in the system for an
erroneous load using the SYSTEM UPLOAD page.
1) Rotate the small FMS knob to the right and select SYSTEM UPLOAD page.
2) Activate the cursor by pushing down on the FMS knob.
3) Rotate the small knob to drop the menu down, and highlight ‘Model 680a Base
Configuration’ in the GROUP field.
4) Press the Enter key.
5) Rotate the small knob to drop the menu down, and highlight ‘Model 680a Base’ in
the ITEM field.
6) Press the Enter key.
7) In the PRODUCT window, the LRUs will populate.
8) Using the arrows on the GTC, highlight CLR ALL at the bottom of the display.
9) Press the Select button on the GTC.
10) Using the arrows on the GTC, highlight CHK CFG at the bottom of the display.
11) Press the Select button on the GTC.

Note: All of the configuration boxes should be checked.

12) Using the arrows on the GTC, highlight LOAD at the bottom of the display.
13) Press the Select button on the GTC.
• A full configuration load takes approximately 30 minutes including the
Card Copy function at the end of the list.
14) Acknowledge when ‘Upload and Crossfill Complete’ is displayed by pressing the
Enter key.
15) Using the arrows on the GTC, highlight UPDT CFG at the bottom of the display.
16) Press the Select button on the GTC.
17) Select YES, and press the Enter key.
18) Acknowledge when ‘Update Config Complete’ is displayed by pressing the Enter
key.

8
Version 1.0 REFERENCE ONLY
 REFERENCE ONLY
Section 4 Reinstalling Options

This section will provide the steps necessary to reload the options that were originally
installed.

CAUTION: Only load the options determined to be installed in Section 1.

Note: Each option is assuming this is the first you are loading. If you have already loaded an
option, then complete this step in place of steps 1-3 of each option the aircraft is
equipped with (not including the unlock cards):
1) Rotate the large knob to the left until in the ITEM field.

• WX-1000E Stormscope Option (FK629S- Stormscope):

1) Rotate the large knob to the left until in the GROUP field.
2) Rotate the small knob to drop the menu down, and highlight ‘Options’ in the
GROUP field.
3) Press the Enter key.
4) Rotate the small knob to drop the menu down, and highlight ‘FK629S-
Stormscope’ in the ITEM field.
5) Press the Enter key.
6) The CARD COPY box should NOT be checked.
7) Using the arrows on the GTC, highlight LOAD at the bottom of the display.
8) Press the Select button on the GTC.
9) Press the Enter key when all the loading is complete to acknowledge the upload is
complete window.

• GDR66 Option (FK632A- VHF Datalink (Datalink/COMM 3)):

1) Rotate the large knob to the left until in the GROUP field.
2) Rotate the small knob to drop the menu down, and highlight ‘Options’ in the
GROUP field.
3) Press the Enter key.
4) Rotate the small knob to drop the menu down, and highlight ‘FK632A- VHF
Datalink (Datalink/COMM 3)’ in the ITEM field.
5) Press the Enter key.
6) The CARD COPY box should NOT be checked.
7) Using the arrows on the GTC, highlight LOAD at the bottom of the display.
8) Press the Select button on the GTC.
9) Press the Enter key when all the loading is complete to acknowledge the upload is
complete window.
9
Version 1.0 REFERENCE ONLY
 REFERENCE ONLY
• Single HF Option FK632B- Single HF (Full UP)):
1) Rotate the large knob to the left until in the GROUP field.
2) Rotate the small knob to drop the menu down, and highlight ‘Options’ in the
GROUP field.
3) Press the Enter key.
4) Rotate the small knob to drop the menu down, and highlight ‘FK632B- Single HF
(Full UP)’ in the ITEM field.
5) Press the Enter key.
6) The CARD COPY box should NOT be checked.
7) Using the arrows on the GTC, highlight LOAD at the bottom of the display.
8) Press the Select button on the GTC.
9) Press the Enter key when all the loading is complete to acknowledge the upload is
complete window.

• Dual HF Option (FK632D- Second HF (Full Up)):

Note: If the aircraft is equipped with a dual HF installation, then both the single and dual
options must be loaded. The dual option loading only loads for the second HF.
1) Rotate the large knob to the left until in the GROUP field.
2) Rotate the small knob to drop the menu down, and highlight ‘Options’ in the
GROUP field.
3) Press the Enter key.
4) Rotate the small knob to drop the menu down, and highlight ‘FK632D- Second HF
(Full Up)’ in the ITEM field.
5) Press the Enter key.
6) The CARD COPY box should NOT be checked.
7) Using the arrows on the GTC, highlight LOAD at the bottom of the display.
8) Press the Select button on the GTC.
9) Press the Enter key when all the loading is complete to acknowledge the upload is
complete window.

• GDL69 Option (FK632L- SiriusXM (Weather/Music)):

1) Rotate the large knob to the left until in the GROUP field.
2) Rotate the small knob to drop the menu down, and highlight ‘Options’ in the
GROUP field.
3) Press the Enter key.
4) Rotate the small knob to drop the menu down, and highlight ‘FK632L- SiriusXM
(Weather/Music)’ in the ITEM field.
5) Press the Enter key.

10
Version 1.0 REFERENCE ONLY
 REFERENCE ONLY
6) The CARD COPY box should NOT be checked.
7) Using the arrows on the GTC, highlight LOAD at the bottom of the display.
8) Press the Select button on the GTC.
9) Press the Enter key when all the loading is complete to acknowledge the upload is
complete window.

• ADF Option (FK6538A- ADF):

1) Rotate the large knob to the left until in the GROUP field.
2) Rotate the small knob to drop the menu down, and highlight ‘Options’ in the
GROUP field.
3) Press the Enter key.
4) Rotate the small knob to drop the menu down, and highlight ‘FK658A- ADF’ in the
ITEM field.
5) Press the Enter key.
6) The CARD COPY box should NOT be checked.
7) Using the arrows on the GTC, highlight LOAD at the bottom of the display.
8) Press the Select button on the GTC.
9) Press the Enter key when all the loading is complete to acknowledge the upload is
complete window.

• ADF2 Option (FK658E- ADF2):

Note: If the aircraft is equipped with a dual ADF installation, then both the single and
dual options must be loaded. This option loading only loads for the second ADF.

1) Rotate the large knob to the left until in the GROUP field.
2) Rotate the small knob to drop the menu down, and highlight ‘Options’ in the
GROUP field.
3) Press the Enter key.
4) Rotate the small knob to drop the menu down, and highlight ‘FK658E- ADF2’ in
the ITEM field.
5) Press the Enter key.
6) The CARD COPY box should NOT be checked.
7) Using the arrows on the GTC, highlight LOAD at the bottom of the display.
8) Press the Select button on the GTC.
9) Press the Enter key when all the loading is complete to acknowledge the upload is
complete window.

11
Version 1.0 REFERENCE ONLY
 REFERENCE ONLY
• GSR56 2 Option (FK676A- Iridium Voice/Datalink):

1) Rotate the large knob to the left until in the GROUP field.
2) Rotate the small knob to drop the menu down, and highlight ‘Options’ in the
GROUP field.
3) Press the Enter key.
4) Rotate the small knob to drop the menu down, and highlight ‘FK676A- Iridium
Voice/Datalink’ in the ITEM field.
5) Press the Enter key.
6) The CARD COPY box should NOT be checked.
7) Using the arrows on the GTC, highlight LOAD at the bottom of the display.
8) Press the Select button on the GTC.
9) Press the Enter key when all the loading is complete to acknowledge the upload is
complete window.

• GSR56 1 Option (FK676N- Iridium Datalink):

1) Rotate the large knob to the left until in the GROUP field.
2) Rotate the small knob to drop the menu down, and highlight ‘Options’ in the
GROUP field.
3) Press the Enter key.
4) Rotate the small knob to drop the menu down, and highlight ‘FK676N- Iridium
Datalink’ in the ITEM field.
5) Press the Enter key.
6) The CARD COPY box should NOT be checked.
7) Using the arrows on the GTC, highlight LOAD at the bottom of the display.
8) Press the Select button on the GTC.
9) Press the Enter key when all the loading is complete to acknowledge the upload is
complete window.
Note: Each option using an unlock card is assuming this is the first you are loading. If you have
already loaded an option with an unlock card, then steps 1 & 2 are already complete.
• CPDLC (VHF DataLink (CPDLC/Link 2000+)):

1) Rotate the dimmer knob to off for L PFD.

2) Remove the 010-01273-26 software loader card from the upper slot of PFD 1 if
installed.
3) Insert the 010-00330-FA CPDLC Unlock card into the upper slot of PFD 1.
4) Rotate the dimmer knob to on for L PFD.
5) PFD 1 should come up in configuration mode.
 PFD 1 should be on the system upload page.
12
Version 1.0 REFERENCE ONLY
 REFERENCE ONLY
6) Activate the cursor by pushing down on the FMS knob.
7) Rotate the small knob to drop the menu down, and highlight ‘Enable_CPDLC’ in
the GROUP field.
8) Press the Enter key.
9) Rotate the small knob to drop the menu down, and highlight ‘FK677A-VHF
DataLink (CPDLC/Link 2000+)’ in the ITEM field.
10) Press the Enter key.
11) Verify that the CARD COPY box is checked.
12) Using the arrows on the GTC, highlight LOAD at the bottom of the display.
13) Press the Select button on the GTC.
14) Press the Enter key when all the loading is complete to acknowledge the upload
is complete window.
15) Rotate the dimmer knob to off for L PFD, and remove the 010-00330-FA CPDLC
Unlock card from the upper slot of PFD 1.

• Steep Approach:

1) Rotate the dimmer knob to off for L PFD.

2) Remove the 010-01273-26 software loader card from the upper slot of PFD 1 if
installed.
3) Insert the 010-00330-G0 Steep Approach Unlock card into the upper slot of PFD 1.
4) Rotate the dimmer knob to on for L PFD.
5) PFD 1 should come up in configuration mode.
 PFD 1 should be on the system upload page.
6) Activate the cursor by pushing down on the FMS knob.
7) Rotate the small knob to drop the menu down, and highlight
‘Enable_SteepApproach’ in the GROUP field.
8) Press the Enter key.
9) Rotate the small knob to drop the menu down, and highlight ‘Steep Approach’ in
the ITEM field.
10) Press the Enter key.
11) Verify that the CARD COPY box is checked.
12) Using the arrows on the GTC, highlight LOAD at the bottom of the display.
13) Press the Select button on the GTC.
14) Press the Enter key when all the loading is complete to acknowledge the upload
is complete window.
15) Rotate the dimmer knob to off for L PFD, and remove the 010-00330-G0 Steep
Approach Unlock card from the upper slot of PFD 1.

13
Version 1.0 REFERENCE ONLY
 REFERENCE ONLY
• SurfaceWatch:

1) Rotate the dimmer knob to off for L PFD.

2) Remove the 010-01273-26 software loader card from the upper slot of PFD 1 if
installed.
3) Insert the 010-00330-5K SurfaceWatch Unlock card into the upper slot of PFD 1.
4) Rotate the dimmer knob to on for L PFD.
5) PFD 1 should come up in configuration mode.
 PFD 1 should be on the system upload page.
6) Activate the cursor by pushing down on the FMS knob.
7) Rotate the small knob to drop the menu down, and highlight
‘Enable_SurfaceWatch’ in the GROUP field.
8) Press the Enter key.
9) Rotate the small knob to drop the menu down, and highlight ‘Enable
SurfaceWatch’ in the ITEM field.
10) Press the Enter key.
11) Verify that the CARD COPY box is checked.
12) Rotate the small knob to drop the menu
13) Using the arrows on the GTC, highlight LOAD at the bottom of the display.
14) Press the Select button on the GTC.
15) Press the Enter key when all the loading is complete to acknowledge the upload
is complete window.
16) Rotate the dimmer knob to off for L PFD, and remove the 010-00330-5K
SurfaceWatch Unlock card from the upper slot of PFD 1.

• ARINC Direct ACARS (ACARS – ARINC Direct):

1) Rotate the dimmer knob to off for L PFD.

2) Remove the 010-01273-26 software loader card from the upper slot of PFD 1 if
installed.
3) Insert the 010-00330-E7 ACARS Unlock card into the upper slot of PFD 1.
4) Rotate the dimmer knob to on for L PFD.
5) PFD 1 should come up in configuration mode.
 PFD 1 should be on the system upload page.
6) Activate the cursor by pushing down on the FMS knob.
7) Rotate the small knob to drop the menu down, and highlight ‘Enable_ACARS’ in
the GROUP field.
8) Press the Enter key.
9) Rotate the small knob to drop the menu down, and highlight ‘Enable ACARS-
ARINC Direct’ in the ITEM field.
10) Press the Enter key.
14
Version 1.0 REFERENCE ONLY
 REFERENCE ONLY
11) Verify that the CARD COPY box is checked.
12) Using the arrows on the GTC, highlight LOAD at the bottom of the display.
13) Press the Select button on the GTC.
14) Press the Enter key when all the loading is complete to acknowledge the upload
is complete window.
15) Rotate the dimmer knob to off for L PFD, and remove the 010-00330-E7 ACARS
Unlock card from the upper slot of PFD 1.

• Honeywell GDC ACARS (ACARS – Honeywell GDC):

1) Rotate the dimmer knob to off for L PFD.

2) Remove the 010-01273-26 software loader card from the upper slot of PFD 1 if
installed.
3) Insert the 010-00330-E7 ACARS Unlock card into the upper slot of PFD 1.
4) Rotate the dimmer knob to on for L PFD.
5) PFD 1 should come up in configuration mode.
 PFD 1 should be on the system upload page.
6) Activate the cursor by pushing down on the FMS knob.
7) Rotate the small knob to drop the menu down, and highlight ‘Enable_ACARS’ in
the GROUP field.
8) Press the Enter key.
9) Rotate the small knob to drop the menu down, and highlight ‘Enable ACARS-
Honeywell GDC’ in the ITEM field.
10) Press the Enter key.
11) Verify that the CARD COPY box is checked.
12) Using the arrows on the GTC, highlight LOAD at the bottom of the display.
13) Press the Select button on the GTC.
14) Press the Enter key when all the loading is complete to acknowledge the upload
is complete window.
15) Rotate the dimmer knob to off for L PFD, and remove the 010-00330-E7 ACARS
Unlock card from the upper slot of PFD 1.

• Universal ACARS (ACARS – Universal):

1) Rotate the dimmer knob to off for L PFD.

2) Remove the 010-01273-26 software loader card from the upper slot of PFD 1 if
installed.
3) Insert the 010-00330-E7 ACARS Unlock card into the upper slot of PFD 1.
4) Rotate the dimmer knob to on for L PFD.
5) PFD 1 should come up in configuration mode.
 PFD 1 should be on the system upload page.
15
Version 1.0 REFERENCE ONLY
 REFERENCE ONLY
6) Activate the cursor by pushing down on the FMS knob.
7) Rotate the small knob to drop the menu down, and highlight ‘Enable_ACARS’ in
the GROUP field.
8) Press the Enter key.
9) Rotate the small knob to drop the menu down, and highlight ‘Enable ACARS-
Universal’ in the ITEM field.
10) Press the Enter key.
11) Verify that the CARD COPY box is checked.
12) Using the arrows on the GTC, highlight LOAD at the bottom of the display.
13) Press the Select button on the GTC.
14) Press the Enter key when all the loading is complete to acknowledge the upload
is complete window.
15) Rotate the dimmer knob to off for L PFD, and remove the 010-00330-E7 ACARS
Unlock card from the upper slot of PFD 1.

• FANS-1/A Enablement:

Note: The ACARS option must be loaded before the FANS-1/A

Enablement. If not, the option will not work, and these
procedures will have to be started all over from the
beginning.
1) Insert the 010-00330-J5 FANS-1/A Unlock card into the upper slot of PFD 1.
2) Rotate the dimmer knob to on for L PFD.
3) PFD 1 should come up in configuration mode.
 PFD 1 should be on the system upload page.
4) Activate the cursor by pushing down on the FMS knob.
5) Rotate the small knob to drop the menu down, and highlight ‘Enable_FANS’ in the
GROUP field.
6) Press the Enter key.
7) Rotate the small knob to drop the menu down, and highlight ‘FANS 1/A Enable’ in
the ITEM field.
8) Press the Enter key.
9) Verify that the CARD COPY box is checked.
10) Using the arrows on the GTC, highlight LOAD at the bottom of the display.
11) Press the Select button on the GTC.
12) Press the Enter key when all the loading is complete to acknowledge the upload
is complete window.
13) Rotate the dimmer knob to off for L PFD, and remove the 010-00330-J5 FANS-
1/A Unlock card from the upper slot of PFD 1.
16
Version 1.0 REFERENCE ONLY
 REFERENCE ONLY
Section 5 CMC Diagnostic Configuration Upload

Since a full configuration load was completed, then the CMC Diagnostics, Aircraft
Configurations, and crew profiles must be loaded.
• Insert the 8445006-13 CMC Configuration SD card into the upper slot of the PFD 1.
• Place the G5000 back in configuration by rotating the dimmer knob to on for PFD 1.
• The system upload page should be visible on the PFD 1.
1) Push in on the knob to get the cursor blinking under the Group line.
2) Rotate the small knob for the drop down menu and press enter on 680A CMC
Config.
3) The cursor will move to the Item line.
4) Rotate the small knob for the drop down menu and highlight 8445006-13 V3.10.
5) Press Enter.
6) Rotate the small knob until the cursor is on the ‘Clear CMC Logs’ Line.
7) Press Enter to place a check mark in the box.
 This is the only way to check this box. Check All will not do it.
 It is very important that this step is completed, or a reload of the
configurations of the entire system will be required to be performed to
remove the amber INCOMPLETE message that will appear.
8) Use the arrow buttons on the GTC and highlight LOAD at the bottom of the
display.
9) Press the Select button on the GTC.
 As the load is commencing, the card copy line will appear and check itself.
• It will load itself.
 Acknowledge when ‘Upload and Crossfill Complete’ is displayed.
• Verify the diagnostic configuration upload succeeded.
1) Push the FMS knob to deactivate the cursor.
2) Rotate the small knob on the GTC, and scroll to the ‘TRANSACTION LOG’ page.
3) Ensure that at the top of the page that the following is present:
 LOADER IMAGE Column will state ‘Not Available’.
 GROUP Column will state ‘680a CMC Config’.
 ITEM Column will state ‘8445006-13 V3.10’.
 STATUS Column will state ‘NO TRANS ID’ in white.
4) There can be no amber or red items in the STATUS column showing anywhere in
the TRANSACTION LOG page.
 If there is, contact Team 680 at 316-517-1695 or [email protected].
5) Use the arrow buttons on the GTC and highlight DETAIL at the bottom of the
display.
6) Press the Select button on the GTC.

17
Version 1.0 REFERENCE ONLY
 REFERENCE ONLY
7) Push in on the FMS knob to activate the cursor.
8) Rotate the small knob and highlight 8445006-13 V3.10.
9) Press the Enter key to expand the values.
10) Verify that the 4 TRANSACTION ID values match the expected values.

Maintenance Logging POF Alert Mapping CMC Alerts CMC Triggers

TRANSACTION ID
(Right Column)
TRANSACTION ID
0x331591C4 0x204FFBAD 0xBOE3E428 0xF78F37DA
(Expected Value)

18
Version 1.0 REFERENCE ONLY
 REFERENCE ONLY
Section 6 Performance & TOLD Database Loading

Performance Database
• Rotate the dimmer knobs off for all three displays to power them off.
• Remove the 8445006-13 CMC Configuration SD card from the upper slot of PFD 1.
• Insert the 010-01585-00 Performance Database SD card into the upper slot of PFD 2.
• Turn on the R PFD dimmer knob.
o Once it loads the files, it will boot up into configuration mode.
o SYSTEM STATUS should show at the top of the screen.
o Pull the 010-01585-00 card from the upper slot of PFD 2.
• Insert the 010-01585-00 Performance Database SD card into the upper slot of the MFD.
• Turn on the MFD dimmer knob.
o Once it loads the files, it will boot up into configuration mode.
o SYSTEM STATUS should show at the top of the screen.
o Pull the 010-01585-00 card from the upper slot of the MFD.
• Insert the 010-01585-00 Performance Database SD card into the upper slot of PFD 1.
• Turn on the L PFD dimmer knob.
o Once it loads the files, it will boot up into configuration mode.
o SYSTEM UPLOAD should show at the top of the screen.
• Activate the cursor by pushing down on the FMS knob.
• Rotate the small knob to drop the menu down, and highlight ‘PERF Table’ in the GROUP
field.
• Press the Enter key.
• Rotate the small knob to drop the menu down, and highlight ‘PERF Table’ in the ITEM
field.
• Press the Enter key.
• It will populate the PRODUCT window with:
o PERF Table GTC 1
o PERF Table GTC 2
o PERF Table GTC 3
o PERF Table GTC 4
o CARD COPY
• Using the arrows on the GTC, highlight CHK ALL at the bottom of the display.
• Press the Select button on the GTC.
• Using the arrows on the GTC, highlight LOAD at the bottom of the display.
• Press the Select button on the GTC. Approximately 25 minutes.

19
Version 1.0 REFERENCE ONLY
 REFERENCE ONLY
Note: Each of the GTC touch controllers will reboot and verification messages will
display as it loads each controller.

• Select the GDU Controls button on one of the touch controllers.

• Press the Enter key to acknowledge the ‘Upload and Crossfill Complete’ window.
TOLD Database
• Rotate the dimmer knob off for L PFD.
• Remove the 010-01585-00 Performance Database SD card from the upper slot of PFD 1.
• Insert the 010-01586-00 TOLD Database SD card into the upper slot of PFD 1.
• Turn on the L PFD dimmer knob.
o It will boot up into configuration mode.
o SYSTEM UPLOAD should show at the top of the screen.
• Activate the cursor by pushing down on the FMS knob.
• Rotate the small knob to drop the menu down, and highlight ‘TOLD Table’ in the GROUP
field.
• Press the Enter key.
• Rotate the small knob to drop the menu down, and highlight ‘TOLD Table’ in the ITEM
field.
• Press the Enter key.
• It will populate the PRODUCT window with:
o TOLD Table GTC 1
o TOLD Table GTC 2
o TOLD Table GTC 3
o TOLD Table GTC 4
o CARD COPY
• Using the arrows on the GTC, highlight CHK ALL at the bottom of the display.
• Press the Select button on the GTC.
• Using the arrows on the GTC, highlight LOAD at the bottom of the display.
• Press the Select button on the GTC. Approximately 10 minutes.

Note: Each of the GTC touch controllers will reboot and verification messages will
display as it loads each controller.

• Select the GDU Controls button on one of the touch controllers.

• Press the Enter key to acknowledge the ‘Upload and Crossfill Complete’ window.

20
Version 1.0 REFERENCE ONLY
 REFERENCE ONLY
Section 7 Transaction Log
• Push the FMS knob to deactivate the cursor.
• Rotate the small knob until on the ‘TRANSACTION LOG’ page.
• Perform the Transaction ID Verification:
o Ensure that the bottom entry shows:
 LOADER IMAGE shows ‘006-B2009-45’
 GROUP shows ‘Model 680a Base Configuration’
 ITEM shows ‘Model 680a Base’
 STATUS shows PASS (in green)
o Verify the transaction logs for the installed options:
 Ensure that there is a line entry for each installed option.
 Ensure that each has a PASS (in green) in the STATUS column.
 Ensure that there is NOT a line entry marked CNFM CFG with ‘FLEET ID
UPDATED’ (in amber) in the STATUS column.
• If it is present in amber the load must be started over.

Note: A line entry of CNFM CFG with AIRCRAFT ID UPDATED (in white) in
the STATUS column, or no line entry with CNFM CFG is acceptable.
o The line entry for the 680a CMC CONFIG was already verified earlier.
o Ensure there are no entries with an amber or red indication in the STATUS
column.
 Green and white are the only acceptable colors for status.

21
Version 1.0 REFERENCE ONLY
 REFERENCE ONLY
Section 8 Aircraft Configuration

Aircraft Configuration
• Fuel & Aircraft Weight
o Verify fuel and aircraft weight are set to the desired unit:
 Rotate the small FMS knob to go to the SYSTEM SETUP page.
 Push the FMS knob to activate the cursor.
 Rotate the large FMS knob to FUEL line in the DISPLAY UNITS box.
 Rotate the small FMS knob and highlight KILOGRAMS or POUNDS.
 Press the Enter key.
 Push the FMS knob to deactivate the cursor.
• Transponder and TCAS Configuration:
o Rotate the small FMS knob to go to the AIRCRAFT CONFIGURATION page.
o Make sure that the registration and VFR code are correct. If not, do as follows:
 Push the FMS knob to activate the cursor.
 The cursor should be on the Aircraft Registration line.
• Enter the aircraft tail number using the keyboard button on the GTC.
• A Hexadecimal code will need to be entered for foreign registered
aircraft.
• The VFR code will need to be set to the correct value for the country
of registry.
o Make sure that the Domain Identifier is correct as follows:
 Access the website: txtavsupport.com and log on using your User Name and
Password.
 Under MY MODELS, select ‘Citation 680A’.
 Under AVIONICS, select ‘Domain Identifier’.
 Find the desired country and the associated three letter Identifier.

Note: An example of a three letter Identifier is “USA” for the United States.

 If the value entered is not correct, enter the three letter Identifier into the
Domain Identifier line using the keyboard button on the GTC.
o Complete the Transponder and TCAS Configuration as follows:
 Using the arrows on the GTC, highlight SET GTX 1 at the bottom of the
display.
• Press the Select button on the GTC.
• Press the Enter key to select YES.
• Press the Enter key to acknowledge.

22
Version 1.0 REFERENCE ONLY
 REFERENCE ONLY
 Using the arrows on the GTC, highlight SET GTX 2 at the bottom of the
display.
• Press the Select button on the GTC.
• Press the Enter key to select YES.
• Press the Enter key to acknowledge.
 Using the arrows on the GTC, highlight SET GTS at the bottom of the
display.
• Press the Select button on the GTC.
• Press the Enter key to select YES.
• Press the Enter key to acknowledge.
 Push the FMS knob to deactivate the cursor.

23
Version 1.0 REFERENCE ONLY
 REFERENCE ONLY
Confirm AIRCRAFT ID
• Rotate the small FMS knob until on the CONFIGURATION MANAGER page.
• Verify that the 2 AIRCRAFT ID numbers match.
• If they do not:
o Use the arrows on the GTC, highlight CNFRM CFG at the bottom of the display.
o Press the Select button on the GTC.
o A pop-up window will appear stating ‘Confirm configuration as expected
configuration?’
o Select OK, and press the Enter key.
o At the top of the screen the EXPECTED CONFIGURATION ID column for the
AIRCRAFT row should now match the ACTUAL CONFIGURATION ID column for the
AIRCRAFT row.

Verify Software & Configuration Load

Note: This is performed while still on the CONFIGURATION MANAGER page.

• Push the FMS knob to activate the cursor.

• Scroll through LRUs and verify that both columns for each show Synchronized in green.
See image below.
o If one or both GSR 56 units are installed, they will not show Synchronized in
green. They will say ‘Status Not Supported’ in gray. This is normal.

24
Version 1.0 REFERENCE ONLY
 REFERENCE ONLY
Transaction Log
• Push the FMS knob to deactivate the cursor.
• Rotate the small knob until on the ‘TRANSACTION LOG’ page.
• Perform the Transaction ID Verification:
o Ensure that the bottom entry shows:
 LOADER IMAGE shows ‘006-B2009-45’
 GROUP shows ‘Model 680a Base Configuration’
 ITEM shows ‘Model 680a Base’
 STATUS shows PASS (in green)
o Verify the transaction logs for the installed options:
 Ensure that there is a line entry for each installed option.
 Ensure that each has a PASS (in green) in the STATUS column.
 Ensure that there is NOT a line entry marked CNFM CFG with ‘FLEET ID
UPDATED’ (in amber) in the STATUS column.
• If it is present in amber the load must be started over.

Note: A line entry of CNFM CFG with AIRCRAFT ID UPDATED (in white) in
the STATUS column, or no line entry with CNFM CFG is acceptable.
o The line entry for the 680a CMC CONFIG was already verified earlier.
o Ensure there are no entries with an amber or red indication in the STATUS
column.
 Green and white are the only acceptable colors for status.

25
Version 1.0 REFERENCE ONLY
 REFERENCE ONLY
Crew Profile Loading
• Turn aircraft power off.
• Remove the 010-01586-00 TOLD Database SD card from the upper slot of PFD 1.
• Insert the new Crew Profile SD card 8431108-9 into the upper slot of the MFD.
• Turn aircraft power on.
• On the left GTC controller:
o Select Aircraft Systems.
o Select Maintenance.
o Select Set Default Profile.
o Select Cessna 680A DEFAULT Profile.
• Select OK when prompted.
• Select Home.
o Select Utilities.
o Select Crew Profile.
o Select Restore Defaults.
o Select OK when prompted.
• In the Default Profile button, the Pilot Profile CRC number is listed.
o Verify that it is: CEB16000

26
Version 1.0 REFERENCE ONLY
 REFERENCE ONLY
Section 9 Final Verification / Return to Service

• Select Home on the left MFD GTC controller.

o Select Utilities.
o Select Setup.
o Select Avionics Status.
o Select the LRU Info tab on the left side.
 Verify that all the LRUs are showing a green check mark.
o Select the MSG button:
 Verify there is no DB Mismatch message present.
 Verify there is no Manifest message present.
 Verify there is no Config message present.
• Select Home on the left MFD GTC controller.
o Select PERF.
o Select Weight and Fuel.
o If the weight is not shown:
 Select Empty Weight, enter the value recorded in section 1, and then select
Enter.
 Select the button at Pilot(s) & Stores and enter the value recorded in
section 1.
• Select Home on the left MFD GTC controller. If equipped with CPDLC and/or FANS-1/A:
o Verify that there is a button in the lower left corner called ATC Datalink.
o Select the ATC Datalink button, and verify:
 A tab on the left side marked CPDLC (if equipped with CPDLC-Link 2000+)
 A tab on the left side is marked ADS-C (if equipped with FANS-1/A).
• If aircraft is equipped with a GDL 69, GSR 56, ACARS, or Stormscope:
o Select Home.
o Select Weather.
o Select Weather Selection.
 Verify Connext Weather is present if equipped with a GSR 56.
 Verify Sirius XM Weather is present if equipped with a GDL 69.
 Verify ACARS Weather is present if the ACARS option is installed.
 Verify Stormscope is present if the Stormscope option is installed.
• Turn aircraft power off.
• Remove the 8431108-9 Crew Profile SD card from the upper slot of the MFD.

27
Version 1.0 REFERENCE ONLY