ISO BLOCK 1057 is a premixed cementitious adhesive mortar used for laying and fixing concrete blocks, bricks, and other masonry units. It has excellent bonding strength, water retention, and workability and is applied as a thin bed adhesive between 10-15mm thick on surfaces that have been cleaned and saturated with water. The product has a shelf life of 12 months when stored properly in original packaging in an air-conditioned environment between 5-40 degrees Celsius.
ISO BLOCK 1057 is a premixed cementitious adhesive mortar used for laying and fixing concrete blocks, bricks, and other masonry units. It has excellent bonding strength, water retention, and workability and is applied as a thin bed adhesive between 10-15mm thick on surfaces that have been cleaned and saturated with water. The product has a shelf life of 12 months when stored properly in original packaging in an air-conditioned environment between 5-40 degrees Celsius.
ISO BLOCK 1057 is a premixed cementitious adhesive mortar used for laying and fixing concrete blocks, bricks, and other masonry units. It has excellent bonding strength, water retention, and workability and is applied as a thin bed adhesive between 10-15mm thick on surfaces that have been cleaned and saturated with water. The product has a shelf life of 12 months when stored properly in original packaging in an air-conditioned environment between 5-40 degrees Celsius.
ISO BLOCK 1057 is a premixed cementitious adhesive mortar used for laying and fixing concrete blocks, bricks, and other masonry units. It has excellent bonding strength, water retention, and workability and is applied as a thin bed adhesive between 10-15mm thick on surfaces that have been cleaned and saturated with water. The product has a shelf life of 12 months when stored properly in original packaging in an air-conditioned environment between 5-40 degrees Celsius.
DESCRIPTION: ISO BLOCK 1057 is a pre-mixed, one compo- nent cementitious-based adhesive mortar for laying and fixing of concrete block, clay brick and other similar masonry units. It has an excellent bonding strength and water retention properties. ISO BLOCK 1057 is consisted of cement, selected natural mineral aggregates and special additives for performance improvement.
USES: APPLICATION PROCEDURE:
Surface preparation Block jointing adhesive for concrete block, clay Blocks and bricks surface should be surfaces brick and other similar masonry units, suitable must be sound, clean and free from dirt, dust, for both interior and exterior use. grease, cement laitance, loosely adhering particles and all other contaminants which will ADVANTAGES: inhibit proper bonding. Absorbent surfaces •Premixed with good and consistent quality. should be saturated thoroughly with clean •Strength compatible to concrete block water. masonry. •Excellent workability, user friendly, just need Mixing to mix with water and apply. Add water according to the desired consisten- •Pre-packed, complementing IBS construction cy (4-6 liters of water for 25 kg powder bag) to achieve good construction quality and less into a clean mixing vessel before slowly adding the ISO BLOCK 1057 powder. Mix thoroughly TECHNICAL PROPERTIES: for 3-5 minutes using mechanical mixer until the homogenous paste is achieved and Composition: Portland cement, selected graded lump-free. Allow mixture to stand for 5 minutes aggregates and special additives and re-stir before use. Re-mix if the mixture is left unattended for more than 15 minutes. Do Appearance: Grey Powder not add extra water or other ingredients. Mix only full bags for best results. Note: In hot Bulk Density: 1.75 kg/ltr weather application, use chilled water to extend the open time of the mixed materials. Mix Density: 2 kg/ltr Maximum grain size: Dmax: 2 mm Application Spread the adhesive to fixing surfaces of Mixing ratio 4 – 6 liters of water for 25 kg bag blocks with a thin bed using notched trowel at Compressive strength bed thickness between 10 to 15 mm. Work in a at 28 days > 5 N/mm2 (ASTM C 109) small area at a time and fix blocks immediately to avoid skin over of adhesive bed. Re-trowel if Open Time May vary depending on porosity of substrate and ambient Approx. 15 minutes (23 °C). the adhesive bed surface had skin over. Use a rubber mallet to tap and adjust the blocks Pot Life: Approx. 1 hours (23 °C) firmly on the adhesive bed to ensure good Application ambient Air (+5 °C) – (+40 °C) contact and alignment is achieved. Remove Temperature excess adhesive before it sets or hardens. Application substrate (+5 °C) – (+40 °C) Allow adhesive bed to set for 24 hours before Temperature any subsequent works. Protect newly applied mortar from sun and wind.
1 ISO BLOCK 1057 - Product Data sheet ISOBIT
BUILDING CHEMICALS Curing: ISO BLOCK 1057 must to be cured by keeping moist for a minimum period of 3 days.
Cleaning: Clean all the tools with water immediately after use. Hardened materials can be removed mechanically only.
Packing: ISO BLOCK 1057 is supplied 25 Kg bags.
Storage: Product must be stored in original unopened packaging, under cover, out of direct sunlight and protect from extreme temperatures. In tropical climates the product must be stored in air-conditioned environment.
Shelf life: Shelf life is up to 12 months when stored as per recommendations.
Health and Safety:
As with all construction chemical product, caution should be alwas be exercised. Protective clothing such as gloves and goggles should be worn. Treat any splashes to the skin or eyes with fresh water immediatly. Should any of the prod- ucts be accidentally awallowed, do not induce vomiting, but call for medical assistance imme- diately.
Prior to use of any ISOBIT product, its subsidiaries, or affiliates, the user should always read and follow the warnings and instructions on the latest version product technical data sheet. ISOBIT guarantees its products against defective materials within the validity period of the product when properly stored, handled, and applied under normal conditions in accordance with ISOBIT's recommendations. ISOBIT does not guarantee the use and application of these products because the terms of their application are beyond its control. ISOBIT reserves the right to change the characteristics of its products and to modify the technical releases without prior notice. NO OTHER WARRANTIES EXPRESS OR IMPLIED SHALL
DBS
ISOBIT CERT Management Systems Certification Body MSCB 157 Certified ISO 9001:2015
