MCQ

1. Which of the following is not a feature of a good control system?
[ a ]
a) Slow response b) Sufficient power handling capacity
c) Good stability d) Good accuracy
2. A control system is generally met with the time response specifications: [ d ]

a) Damping factor b) Setting time c) Steady state accuracy d) All of the mentioned
3. What is the relation between output response and input signal in closed loop system?
a) Nonlinear b) Linear c) Exponential d) Parabolic [ b ]
4. The overall transfer function of two blocks in parallel are : [ a ]
a) Sum of individual gain b) Product of individual gain

c) Difference of individual gain d) Division of individual gain
5. The overall transfer function from block diagram reduction for cascaded blocks is : [ b ]
a) Sum of individual gain b) Product of individual gain

c) Difference of individual gain d) Division of individual gain
6. Transfer function of the system is defined as the ratio of Laplace output to Laplace input
considering initial conditions________ [ c ]
a) 1 b) 2 c) 0 d) infinite
7. In an open loop control system [ a ]

(a) Output is independent of control input (b) Output is dependent on control input
(c) Only system parameters have effect on the control output (d) None of the above
8. An automatic toaster is a ______ loop control system. [ a ]

(a) open (b) closed (c) partially closed (d) any of the above
9. A closed loop system is distinguished from open loop system by which of the following ?[ b ]
(a) Servomechanism (b) Feedback (c) Output pattern (d) Input pattern
10. With feedback _____ increases. [ a ]
(a) system stability (b) sensitivity (c) gain (d) effects of disturbing signals A
11. With feed back _____ reduces. [ b ]
(a) system stability (b) system gain (c) system stability and gain (d) none
12. A.C. servomotor is basically a [ c ]
(a) universal motor (b) single phase induction motor
(c) two phase induction motor (d) three phase induction motor
13. Which among the following controls the speed of D.C. motor? [ d ]
a. Galvanometer b. Gauss meter c. Potentiometer d. Tachometer
14. In block diagram representation, what do the lines connecting the blocks, known as?
a. Branches b. Nodes c. Datums d. Sources [ a ]
15 In a signal flow graph method, how is an overall transfer function of a system
obtained? [ c ]
a. Poisson’s equation b. Block diagram reduction rules

c. Mason’s equation d. Lagrange’s equation
16. In a second order system, if the damping ratio is greater than equal to ‘1’, then what
would be the nature of roots? [ c ]
a. Imaginary b. Real and equal c. Real but not equal d. Complex conjugate
17. Which among the following is represented by a parabolic input signal? [ d ]
a. Position b. Force c. Velocity d. Acceleration
18. In time domain system, which response has its existence even after an extinction of
transient response? [ c ]
a. Step response b. Impulse response

c. Steady state response d. All of the above
19. Two loops are said to be non-touching only if no common ______exists between
them. [ d ]
a. Loop b. Feedback path c. Branch d. Node
20. For the elimination of feedback loops, the derivation based on transfer function of
______ loop is used. [ b ]
a. Open b. Closed c. Both a and b d. None of the above
21. Traffic light system is the example of___________ [ a ]
A . Open-loop system b.Closed-loop system c.All of above d. None of above
22. The impulse response of an RL circuit is_______________ [ d ]
a. Step function
b. Parabolic function
c. Rising exponential function
d. Decaying exponential function
23. The most powerful controller is_______________ [ c ]
1. PI Controller
2. PD controller
3. PID Controller
4. None
24. The controller required to handle fast process load changes is______________ [ b ]
1. PI Controller
2. PD controller
3. PID Controller
4. None
25. Slow response of an over-damped system can be made faster with the help of ______
controller. [ a ]
1. P
2. PD
3. PI
4. Remote
26. Loop gain is equal to_________________
1. Product of all branch gains while traversing the forward path
2. Summation of all branch gains in a loop
3. Product of all branch gains in a loop
4. Sum of all branch gains while traversing the forward path
Answer: Product of all branch gains while traversing the forward path
27. The impulse response of an RL circuit is_______________
a. Step function
b. Parabolic function
c. Rising exponential function
d. Decaying exponential function
Answer: Decaying exponential function
28. A major part of the automatic control theory applies to the: [ b ]
a. Casual systems
b. Linear Time invariant systems
c. Time variant systems
d. Non-linear systems
29. What describes the behavior of the control systems? [ c ]
A. Equations
B. Rational Equations
C. Differential Equations
D. Integration Equations
30. How many types of control systems are there? [ a ]
A. 2
B. 3
C. 4
D. 5
31. ___ loop is a control system in which the desired output

signal is not affected by the control action [ a ]
A. Open
B. Closed
C. Both A and B
D. None of the above
32. What is an open loop control system also known as? [ c]
A. Non-feedback control system

B. Control system without feedback
C. Both A and B
33. Which of the following is/are the example(s) of the open

loop control system? [ c]
A. Automating washing machine

B. Immersion rod
C. Both A and B
34. What is/are the advantage(s) of an open-loop control

system? [ d]
A. Simple
B. Economical
C. Low maintenance
D. All of the above
35. What is/are the disadvantage(s) of an open loop control

system? [ d]
A. Inaccurate
B. Not reliable
C. Slow
D. All of the above

MCQ

Uploaded by

Copyright:

Available Formats

MCQ

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

MCQ

Uploaded by

Copyright:

Available Formats

1. Which of the following is not a feature of a good control system?

c) Good stability d) Good accuracy

2. A control system is generally met with the time response specifications: [ d ]

4. The overall transfer function of two blocks in parallel are : [ a ]

a) Sum of individual gain b) Product of individual gain

a) Sum of individual gain b) Product of individual gain

7. In an open loop control system [ a ]

8. An automatic toaster is a ______ loop control system. [ a ]

10. With feedback _____ increases. [ a ]

12. A.C. servomotor is basically a [ c ]

(a) universal motor (b) single phase induction motor

a. Poisson’s equation b. Block diagram reduction rules

a. Step response b. Impulse response

28. A major part of the automatic control theory applies to the: [ b ]

29. What describes the behavior of the control systems? [ c ]

30. How many types of control systems are there? [ a ]

31. ___ loop is a control system in which the desired output

32. What is an open loop control system also known as? [ c]

A. Non-feedback control system

33. Which of the following is/are the example(s) of the open

A. Automating washing machine

34. What is/are the advantage(s) of an open-loop control

35. What is/are the disadvantage(s) of an open loop control

You might also like