www.fine-tek.

com

FMCW Radar Level Transmitter

PRODUCT INTRODUCTION

FMCW Radar level transmitter is a non contact FEATURES

measuring device, which is suitable for high temp.,
Non contact measuring
high pressure, and corrosive applications. It is
easy to install and free of maintenance, especially Corrosive and toxic liquid, hydrocarbons,
for the high accuracy requirement environment. slurries
Not affected by specific gravity, pressure,
PRINCIPLE temperature, viscosity, foam, and dust
FMCW radar adopts a high frequency signal, 5 digits LCM display
which is emitted via an antenna and swipe Indicate signal wave inside the silo.
frequency increment by 0.5GHz during the Selection of Different Measurement unit(m,
measurement, reflected by the target surface and cm, mm, inch, Ft, %, mA)
received at a time delay. The frequency difference, Measuring distance and actual level.
which is calculated from the transmitting frequency
Language selection of traditional Chinese,
and the received frequency, which is directly
simplified Chinese, English.
proportional to the measured distance (or material
surface). 4-20mA / 4 wires / 2 wires
The frequency difference then is processed by Modbus RS-485 to enhance isolation and
Fast Fourier Transformation (FFT) to identify the easy for remote control.
signal in Intermedium Frequency (IF). This FMCW CE standards for isolation(EFT 2000V, B class
radar is innate with signal / noise enhancement or better)
and filtering of echo-back via Phase-Lock Loop
Suitable for mid-range signal
(PLL) circuit that is the best solution for complex
environment and high accuracy measurement. 4mA, 20mA output
Isolated circuit design.
26GHz JFR2 series could measure all kinds
of material.

Design formula

TEST STANDARDS
High voltage : IEC60947-2
Isolated resistance : IEC60092-504
LINEARITY DIAGRAM Power supply change : IEC60092-504
Accuracy Power supply failure : IEC60092-504
cm
12
Electrical burst testing : IEC61000-4-4
10 A0.4% Voltage DIPS : IEC61000-4-11
8 A0.4%
6 A30mm A0.4% Humidity : IEC60068-2-30
A20mm
A0.2%
4
A10mm
High/Low temperature test : IEC60068-2-38
2
A5mm
0 A3mm A0.2%
IP protection rating : IEC60529
-2
-4
-6
-8
-10
-12
-14
-16
0.5m 5m 15m 20m
Distance to flange 1
SPECIFICATION (26GHz 4-wire)

f98 f98

1/2"PF 1/2"PF
217
Dimensions 210

(Unit:mm) 1-1/2"PF
60 60
2"NPT or 2"PF
PTFE PTFE
f43 f56

Model JFR-204 JFR-214

General liquid /suitable for acid and
Medium General liquid and solid
alkaline in liquid
Min. Dielectric 1.5
constant (solid)
Min. Dielectric 1.4
constant (liquid)
Measuring range Liquid 30m Solid 20m Liquid 30m

Accuracy A3 mm

Repeatability A1 mm

Digital communication RS485 (Isolated)

Ambient temperature -40~90 BC(LCM<75BC)

Operating temperature -40~200 BC

Operating pressure 0~40 bar

Frequency K Band

Analog output 4~20mA / 4 Wire

Protection rating IP67

Power supply 9.5~30Vdc

Local display 5 digits LCM display

Housing material Aluminum

Antenna type Horn (43D) Lens (56D)

Half-power beam width ±9°

Antenna material SUS316+PTFE PTFE

Blind distance 500mm

2
 f98
f98

f98
1/2" PF compressed
air input
1/2" PF compressed
air input
1/2" PF 190
369 476
1-1/2" NPT
2"PF
Dimensions 2"PF
43

(Unit:mm) 162
270
f43

f100
f140

Model JFR-224 JFR-234 JFR-244

Medium General liquid and solid

Long dlstance Super dlstance Corrosion type acid and
Suitable For
measurement measurement alkaline liquid
Min. Dielectric
constant (solid) 1.5

Min. Dielectric
constant (liquid) 1.4

Measuring range Liquid 40m Solid 30m Liquid 70m Solid 50m Liquid 20m Solid 15m
A3mm @distance<40m
Accuracy A3 mm A0.01%F.S. @distance>40m A3 mm

Repeatability A1 mm
Digital communication RS485 (Isolated)

Ambient temperature -40~90 BC(LCM<75BC)

Operating temperature -40~200 BC

Operating pressure 0~40 bar

Frequency K Band

Analog output 4~20mA / 4 Wire

Protection rating IP67

Power supply 9.5~30 Vdc

Local display 5 digits LCM display

Housing material Aluminum

Antenna type High gain horn (100) High gain horn (140) Lens(43DS)

Half-power beam width ±5° ±3° ±10°

Antenna material SUS 316 PTFE

Blind distance 500 mm

P.S. For JFR-224 and JFR-234, customer can connect the compressed air with 1/8"PT thread
connector to avoid dust adhered. 3
SPECIFICATION (26GHz 2-wire)

f98
f98

1/2"PF 1/2"PF
210 217

Dimensions 1-1/2"PF
(Unit:mm) 60
2"NPT or 2"PF 60
PTFE PTFE
f43 f56

Model JFR-202 JFR-212

General liquid /suitable for acid and
Medium General liquid and solid
alkaline in liquid
Min. Dielectric 1.5
constant (solid)
Min. Dielectric 1.4
constant (liquid)
Measuring range Liquid 20m Solid 10m Liquid 20m

Accuracy A5mm
Repeatability A3mm
Digital communication HART
Ambient temperature -40~90BC(LCM<75BC)
Operating temperature -40~200BC
Operating pressure 0~40 bar
Frequency K Band
Analog output 4~20mA

Protection rating IP67

Power supply 24VdcA10%

Local display 5 digits LCM display

Housing material Aluminum

Antenna type Horn (43D) Lens (56D)

Half-power beam width ±9°

Antenna material SUS 316 + PTFE PTFE

Blind distance 500 mm

4
 f98
f98
f98

1/2" PF compressed
air input
1/2" PF compressed 190
1/2" PF
air input 1-1/2" NPT
369 476
2"PF 43

Dimensions
2"PF 270 f43
(Unit:mm) 162

f100
f140

Model JFR-222 JFR-232 JFR-242

Medium General liquid and solid

Long dlstance Super dlstance Corrosion type acid and
Suitable For
measurement measurement alkaline liquid
Min. Dielectric 1.5
constant (solid)
Min. Dielectric 1.4
constant (liquid)
Measuring range Liquid 30m Solid 20m Liquid 35m Solid 30m Liquid 15m
A3mm @distance<40m
Accuracy A5 mm A0.01%F.S. @distance>40m A5 mm
Repeatability A3mm
Digital communication HART
Ambient temperature -40~90BC(LCM<75BC)
Operating temperature -40~200BC
Operating pressure 0~40 bar
Frequency K Band
Analog output 4~20mA
Protection rating IP67

Power supply 24VdcA10%

Local display 5 digits LCM display

Housing material Aluminum

Antenna type High gain horn (100D) High gain horn (140D) Lens (43DS)

Half-power beam width ±5° ±3° ±10°

Antenna material SUS 316 PTFE

Blind distance 500 mm

P.s. For JFR-222 and JFR-232, customer can connnect the compressed air with 1/8"PT thread connector
to avoid dust adhered. 5
WIRING/CALIBRATION

WIRING INFORMATION WIRING DIAGRAM

RS485 wiring JFR-2X4 JFR-2X2

1 V+
POWER
2 V-
DC24V
5
6

1 2 3 4 5 6 1 2
TR- TR+

1 Power Supply: V+
RS232/485
Converter
2 Power Supply: V-
3 Analog Output: I+ (4~20mA)
RS232 Interface / USB Interface
4 Analog Output: I- (4~20mA)
5 Communication: TR+ (RS485)
JFR Series and Indicator(External Power) 6 Communication: TR- (RS485)

1 V+
CALIBRATION
POWER
2 V-
3
DC24V Two ways to calibrate the JFR Series:
4 4-wire:
I+ 1. Display/Adjustment module
2. By pcbased fas soft ware
I-
2-wire:
Panel Meter
1. Display/Adjustment module
2. HART
1 V+
POWER Adjustment module is an adjustment tool with
DC24V
4 buttons to click on. It also has a transparent
2
V- window to allow display reading.

24V DC. 4-20mA Modbus 24V DC

+ - + - D+ D- + -

5 digits LCM displat

[ ] Button [ ] Button
-Enter Edit status -Select Edit
-Confirm Edit -Select parameter
-Confirm parameter -Parameter
modification

[ ] Button [ ] Button
-Return -Increase
-Cancel -Select
6
PARAMETER SETTING

Measurement bench-mark starts at contact surface of connection.

Low level calibration
High level calibration
Blind Distance
Measuring Distance Setup

Note: Be aware of blind distance when measuring material high level.(Shown in )

100%

0%

7
INSTALLATION

1. JFR-20x can be hidden in the extension tube, the 4. JFR-24x can be hidden in the extension tube, the
recommendation of the tube diameter D and length L recommendation of the tube diameter D and length L
are shown in the table. are shown in the table.

L
L
D
D
Diameter D (Inch) Length L (Inch)
2" L£ 160 Diameter D (Inch) Length L (Inch)

4" L£ 300 2" L£ 100

5" L£ 400 4" L£ 200

6" L£ 500 5" L£ 300

6" L£ 400

2. JFR-21x can be hidden in the extension tube, the 5. Installation recommendations are as follows :
recommendation of the tube diameter D and length L (1) Antenna installation angle to be perpendicular to the
are shown in the table. Horizontal.
(2) JFR installation position with the drum wall suggestions
Are as follows :
Installation location A should be less than 1/6D
Range with A relation is as follows :
a.H<10m, A>300mm
L b.10m<H<20m, A >600mm
D c.H>20m, A>900mm

Diameter D (Inch) Length L (Inch)

3" L£ 200
4" L£ 300 A
5" L£ 400
H

3. JFR-22X and JFR-23X can be hidden in the extension

tube, the recommendation of the tube diameter D and
D
length L are shown in the table.
(3) Extended tube is suggested to do the welding process
from outside; welding process from inside, the bulges
might affect the signal transmission. The joint part of
extended tube cannot be less than “D”.

D
L
D
Model Diameter D (Inch) Length L (Inch)
JFR-22X D>100 L£ 150
JFR-23X D>140 L£ 270

8
2. Radar installation should not be too close to the drum 6. If drum internal agitator will have a strong vortex and
wall, avoid the drum wall attachment material reflection foam, drum must increase waveguide, the upper
interference. waveguide drill vent holes to ensure the correctness of
the measured value.

vent hole

X
X
3. Radar installation not too close to the drum bracket to 7. Installation should be avoided in the feed inlet position,
avoid reflection is incorrect avoid material interference or obstacles interference.

X X

4. When obstructions inside the tank, tank be fitted with 8. Installation should be avoided in the top center of the
eflectors, steer clear of the error echo reflected to the arch or round barrel will cause multiple echo reflections.
receiver, causing radar miscalculation.

Reflector

X
X

5. Outdoor installation should take shade or rain-proof

measures.

9
MODEL NUMBER / ORDER CODE COMPARISON TABLE

Model Number Order Code

JFR-204 JFR20000-A1MB
JFR-214 JFR20000-A521
JFR-224 JFR20000-A2
JFR-234 JFR20000-A3MA
JFR-244 JFR20000-A421
JFR-202 JFR20000-A1
JFR-212 JFR20000-A5
JFR-222 JFR20000-A2
JFR-232 JFR20000-A3
JFR-242 JFR20000-A4

10
ORDER INFORMATION

09 10 11 12 13 14 15 16 17 18 19 20 21 22 23

JFR 2 0 0 0 0 -999999999999999

09 10 Antenna type
A1: Horn(43D)
A2: Horn(100D/162L)
A3: Horn(140D/270L)
A4: Lens(43DS)
A5: Lens(56D)
B1: Horn(100D/126L)
B2: Horn(140D/202L)

11 12 Antenna material
MA: SUS 304
MB: SUS 316
MC: SUS 316L
21: PTFE coating

Connection
13 14 15 16 17 18

Flange B1: 1-1/2" 03: PF male

AK: JIS-FF B2: 2" 07: NPT male
AN: ANSI-RF B4: 2-1/2" 40: 5 kg/cm2
AS: DIN-FF B5: 3" 42: 10 kg/cm2
B7: 4" 48: 150 Lbs
Thread B8: 5" 49: 300 Lbs
AA: JIS B9: 6" 57: PN10
AC: ANSI E3: DN65 58: PN16
E4: DN80 59: PN25
60: PN16

※ (1) JFR-202,204 thread connection 1-1/2" PF only

(2) JFR-212,214 thread connection 2" PF, NPT only
(3) JFR-222,224 thread connection 2 " PF only
(4) JFR 234,232 thread connection 2"PF only
(5) JFR 234,232 thread connection 1-1/2"NPT only
(6) Please do check Radar antenna can be direct fitted
in flange connection and nozzle below is the suggestion
(7) 2"Flang is applicable in open area

Type Opening Flange size

JFR-21X 56mm 2-1/2"
JFR-22X 100mm 4"
JFR-23X 140mm 6"
JFR-24X 44mm 2"

11
 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23

JFR 2 0 0 0 0 -999999999999999

19 20 Flange material
MA: SUS 304
MB: SUS 316
MC: SUS 316L
MD: SS41 zinc coating
18: PP
21: PTFE
00: None

21 Output
A: Loop Power 24 Vdc with HART
B: 4-Wire 24Vdc 4~20mA with RS-485
C: Loop Power 24 Vdc, 4~20mA

22 Accuracy
A: K3mm
B: K5mm
C: K10mm
D: K20mm
※2 Wire only option A:A5mm or C:A10mm

23 Measuring distance
A: 10m
B: 20m
C: 30m
D: 40m
E: 70m

12
 JFR Radar Level Transmitter
Customer Information Prepared by: Date:
Company: Industry:

E-mail: Phone Number:

Address:

Application Information
B.1 Measuring Material Information
Application Description:

Installation Area: 9 Storage tank 9 Process tank 9 Open-air application

Material Status : 9 Liquid 9 Slurry/ Sludge/ Paste 9 S olid/ Granulate/Grain 9 Powder
9 1.4~1.9 9 4.0~10.0
Material Name : Dielectric Constant 9 2.0~2.5 9 >10
9 2.6~4.0 9 Unknow

B.2 Power Supply

9 DC : 9 AC :

B.3 Output Signal

Analog : 9 4~20 mA-4 Wire 9 4~20mA 2-Wire
Digital : 9 RS-485 9 HART 9 Other

B.4 Measuring range

Measuring range: meters

B.5 Measuring Condition

Operating Temperature
Max: ℃ Min: ℃
Abient Temperature
Max: ℃ Min: ℃
Operating Pressure
Max: Bar Min: Bar

B.6 Connection
Connection: 9 Threaded 9 Flange
Size and Standard: Flange Material:
B.7 Tank Information
9 Vertical Cylinder 9 Horizontal Cylinder 9 Spherical
Tank Shape
9 Cubical/rectangular 9 Other:
Tank Material 9 Cubical 9 Plastic 9 Cement 9 Other

9 Metal

9 Plastic

Tank Bottom
9 Cement

9 Other

Tank
Tank Height (H): m D3 D1
Tank Diameter (W): m
Cone Height (H1): m
Nozzle
(Ignore cone height with flat/disk bottom )
L

Radar
Distance to tank wall(D1): m D

Nozzle
9 Yes
Nozzle Diameter (L): m Ladder
Nozzle Height (D): m
9 NO
H
Ladder
9 Yes W
Distance to rada (D3): m
9 NO

Heater
9 Yes
9 NO
H1

Other Internal Obstacles

9 Yes
9 NO
 實 蹟 說明

Power plant Oil Factory Government agencies Pharmaceutical Factory

port wave height edtection Process Oil Detection flood prevention and control Boiler Liquid Detection

Feed industry Oil Factory Plastic industry Feeding plant

butter storage detection Soybean oil level detection chemical detection Corn storage tank detection
 Global Network

Germany
China

Taiwan U.S.
Singapore
Malaysia

Indonesia

Asia North America Europe

Taiwan California, U.S. Germany
FineTek Co., Ltd. - Taipei Head Quarter Aplus Finetek Sensor Inc. - US Office FineTek GmbH - Germany Office
No.16, Tzuchiang St., Tucheng Industrial Park 355 S. Lemon Ave, Suite D, Walnut, Bei den Kämpen 26
New Taipei City 236, Taiwan CA 91789 21220 Seevetal-Ramelsloh, Germany
TEL: 886-2-2269-6789 TEL: 1 909 598 2488 TEL: +49-(0)4185-8083-12
FAX: 886-2-2268-6682 FAX: 1 909 598 3188 FAX: +49-(0)4185-8083-80
EMAIL: [email protected] EMAIL: [email protected] EMAIL: [email protected]

China
Fine automation Co., Ltd. - Shanghai Factory Mütec Instruments GmbH - Germany Office
No.451 DuHui Rd, MinHang District, Shanghai, Bei den Kämpen 26
China 201109 21220 Seevetal-Ramelsloh, Germany
TEL: 86-21-6490-7260 TEL: +49-(0)4185-8083-0
EMAIL: [email protected] FAX: +49-(0)4185-8083-80
EMAIL: [email protected]
Singapore
FineTek Pte Ltd. - Singapore Office
No. 60 Kaki Bukit Place, #07-06 Eunos
Techpark 2 Lobby B, Singapore 415979
TEL: 65-6452-6340
EMAIL: [email protected]

Indonesia
FineTek Co., Ltd. - Indonesia Office
Ruko Golden 8 Blok H No.38
Gading Serpong, Tangerang, Indonesia
TEL: 62 (021)-2923-1688
EMAIL: [email protected]

Malaysia Distributor:
FineTek Co., Ltd. - Malaysia Office
8-05, Plaza Azalea, Persiaran Bandaraya,
Seksyen 14, 40000 Shah Alam, Selangor, Malaysiac
TEL: 603-5524-7168
EMAIL: [email protected]

08-JFREP, 010417