0% found this document useful (0 votes)
192 views16 pages

Micropile - Design and ALLpile Analysis

The document provides information on the capacity calculations for a micropile with a diameter of 200 mm. It includes soil properties, pile properties, and calculations of ultimate capacity considering side resistance, tip resistance, and weight of the soil above ground. The ultimate capacity is calculated as 465.362 kN with a factor of safety of 1.1, providing an allowable load of 424.3 kN.

Uploaded by

kartik v
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
192 views16 pages

Micropile - Design and ALLpile Analysis

The document provides information on the capacity calculations for a micropile with a diameter of 200 mm. It includes soil properties, pile properties, and calculations of ultimate capacity considering side resistance, tip resistance, and weight of the soil above ground. The ultimate capacity is calculated as 465.362 kN with a factor of safety of 1.1, providing an allowable load of 424.3 kN.

Uploaded by

kartik v
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 16

2

Micropile dia = 200 mm Skin Area per m, As= 0.628 Base Area, Ab = 0.031 m
Factor of Safety (FoS) = 1.500
Pile Capacity (kN)
Unit
Skin Skin Cumulative End Bear at depth, Pile Ultimate Pile Allowable 0 1000 2000 3000 4000 5000
Depth Interval Avg SPT End Bear at
Fric, fs = Fric, Fs Skin Fric, Fs qb=min(400N/3, Capacity, Qult = Capacity, Qall = 0
(m) Value, N depth, Qb (kN)
2N (kN) (kN) 2
10000) (kN/m ) Fs+Qb (kN) Qult/FoS (kN)
2
(kN/m )
1 10 20 12.6 12.6 1333.3 41.9 54.5 36.3
2 15 30 18.8 31.4 2000.0 62.8 94.2 62.8 5
3 10 20 12.6 44.0 1333.3 41.9 85.9 57.2
4 15 30 18.8 62.8 2000.0 62.8 125.7 83.8
5 17 34 21.4 84.2 2266.7 71.2 155.4 103.6
6 10 20 12.6 96.8 1333.3 41.9 138.6 92.4 10
7 9 18 11.3 108.1 1200.0 37.7 145.8 97.2
8 15 30 18.8 126.9 2000.0 62.8 189.8 126.5
9 22 44 27.6 154.6 2933.3 92.2 246.7 164.5

Depth (m)
10 24 48 30.2 184.7 3200.0 100.5 285.3 190.2 15
11 25 50 31.4 216.1 3333.3 104.7 320.9 213.9
12 18 36 22.6 238.8 2400.0 75.4 314.2 209.4
13.5 7 14 13.2 252.0 933.3 29.3 281.3 187.5
15 5 10 9.4 261.4 666.7 20.9 282.3 188.2 20
16.5 9 18 17.0 278.3 1200.0 37.7 316.0 210.7
18 11 22 20.7 299.1 1466.7 46.1 345.2 230.1
19.5 15 30 28.3 327.4 2000.0 62.8 390.2 260.1
21 19 38 35.8 363.2 2533.3 79.6 442.8 295.2 25
23 22 44 55.3 418.5 2933.3 92.2 510.6 340.4
24 28 2464.8 1548.6 1967.1 10000.0 314.2 2281.3 1520.8

30
Specified Working Load = 1400 kN Depth required = 7 m
Structural Capacity
WITH CASING
Pile Diameter, f = 200 mm
Grade, fcu 30 cement grout (w/c ratio = 0.45)
Use Casing Pipe, f 100 mm 6 mm thk
fy = 500 N/m

Use Rebar, f 20 mm 4 Nos

Area of Steel & Concrete


As1 (provided) = Sprbars2
2
As = 1256.6371 mm
As2 (provided) = 2prt
2
As = 1771.8583 mm
2
Ac = p*d /4
2
Ac = 31420 mm

Ultimate Compression Load,


fu = 0.4fcu*Ac + 0.75fy*(As1+As2)
fu = 1512725.7 N
fu = 1512.7257 kN

Taking Factor of Safety (FoS) = 1.1


fall = fu/FoS
fall = 1375.2 kN

Ultimate Tension Load,


fu = 0.55fy*(As1+As2)
fu = 832836.21 N
fu = 832.83621 kN

Taking Factor of Safety (FoS) = 1.1


fall = fu/FoS
fall = 757.1 kN

Micropile Details

Micropile, Dia 200 mm

APICasing
Pipe Pipe inside
f 100 mm
6 mm thk

Clear spacing/Cover = 50.0 mm

Cement grout, G 30 N
W/C Ratio 0.45 min
WITHOUT CASING
Pile Diameter, f = 200 mm
Grade, fcu 30 cement grout (w/c ratio = 0.45)
Use Rebar, f 20 mm 4 Nos
2
fy = 500 N/mm

Area of Steel & Concrete


As (provided) = Sprbars2
2
As = 1256.64 mm
2
Ac = p*d /4
2
Ac = 31420 mm

Ultimate Compression Load,


fu = 0.4fcu*Ac + 0.75fy*As
fu = 848279 N
fu = 848.279 kN

Taking Factor of Safety (FoS) = 1.1


fall = fu/FoS
fall = 771.2 kN

Ultimate Tension Load,


fu = 0.55fy*As
fu = 345575 N
fu = 345.575 kN

Taking Factor of Safety (FoS) = 1.1


fall = fu/FoS
fall = 314.2 kN

Micropile Details

Micropile, Dia 200 mm

R6 Spiral Link

Rebar

Cement grout, G 30 N
W/C Ratio 0.45
Micropile with pressure grout – in ALLPILE so�ware
VERTICAL ANALYSIS Figure 1
Loads:
Load Factor for Vertical Loads= 1.0
Load Factor for Lateral Loads= 1.0
Loads Supported by Pile Cap= 0 %
Shear Condition: Static

(with Load Factor)


Vertical Load, Q= 111.2 -kN

Profile:
Pile Length, L= 10.0 -m
Top Height, H= 0.000 -m
Slope Angle, As= 0.0
Batter Angle, Ab= 8.5

Micropile (MiniPile)

Soil Data: Pile Data:


Depth Gamma Phi C K e50 or Dr Nspt Depth Width Area Per. I E Weight
-m -kN/m3 -kN/m2 -MN/m3 % -m -cm -cm2 -cm -cm4 -MPa -kN/m
0 18.078 33.1 0.000 12.404 35.04 10 0.0 15 54.8 47.1 1301.9 199938 0.420
2.134 20.279 0.0 58.892 82.488 0.88 10 4.6 17 377.4 55.9 5058.7 20683 0.665
4.572 8.677 34.2 0.000 11.563 41.10 13 10.0
6.706 10.988 32.5 54.104 192.281 0.61 18
9.144 9.275 36.5 0.000 18.322 54.06 20

Vertical Capacity:
Weight above Ground= 0.00 Total Weight= 4.16-kN *Soil Weight is not included
Side Resistance (Down)= 358.973-kN Side Resistance (Up)= 358.973-kN
Tip Resistance (Down)= 106.390-kN Tip Resistance (Up)= 0.000-kN
Total Ultimate Capacity (Down) Qult= 465.362-kN Total Ultimate Capacity (Up)= 363.136-kN
Total Allowable Capacity (Down) Qallow= 292.510-kN Total Allowable Capacity (Up) Qallow= 183.649-kN
OK! Qallow > Q

Settlement Calculation:
At Q= 111.20-kN Settlement= 0.08009-cm
At Xallow= 2.50-cm Q= 99999.00000-kN

Note: If the program cannot find a result or the result exceeds the upper limit. The result will be displayed as 99999.

CivilTech Micropile with Pressure Grout


Software Two Sections. No Friction on top section
ALL-PILE CivilTech Software www.civiltech.com Licensed to

SOIL STRESS, SIDE RESISTANCE, & AXIAL FORCE vs DEPTH


Based on Ultimate Load Condition

Depth (Zp) Vertical Stress -kN/m2 Side Resistance-kN/m2 Axial Force -kN Depth (Zp)
from from
Pile Top -m -100.00 0 +100.00 -200.00 Up 0 Down +200.00 -500 Up 0 Down +500 G-kN/m3 Phi C-kN/m2 k-MN/m3e50 % Pile Top-m
0 0
18.078 33.1 0.000 12.404
Medium dense silty SAND

1 1

2 2
20.279 0.0 58.892 82.488 0.88
Soft Clay
3 3

4 4

8.677 34.2 0.000 11.563


5 Medium dense fine SAND 5

6 6

7 10.988 32.5 54.104 192.281 0.61 7


Very stiff sandy SILT

8 8

9 9
9.275 36.5 0.000 18.322
Medium dense gravelly SAND
10 Pile Tip 10
Top Vertical Stress=0.000 Max. Side Resistance=118.68 Top Uplift=363.1
Max. Vertical Stress=64.142 Top DownWard=465.4 Atip=377-cm

11 11

12 12

13 13

14 14

15 15

CivilTech Micropile with Pressure Grout


Software Two Sections. No Friction on top sectionFigure 1
ALL-PILE CivilTech Software www.civiltech.com Licensed to

Vertical Load vs. Total Settlement

400

360

320
Compression Load, Qdw -kN

280

240

200

160

120

80

40

0
0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0

Total Settlement, X -cm


Total Stiffness, Kqx= 1388.39 -kN/-cm

CivilTech Micropile with Pressure Grout


Software Two Sections. No Friction on top sectionFigure 1
ALL-PILE CivilTech Software www.civiltech.com Licensed to

Vertical Load vs. Total Settlement

400

360

320
Compression Load, Qdw -kN

280

240

200

160

120

80

40

0
0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0

Total Settlement, X -cm


Total Side Tip

CivilTech Micropile with Pressure Grout


Software Two Sections. No Friction on top sectionFigure 1
LATERAL ANALYSIS 5.0
Loads:
Load Factor for Vertical Loads= 1.0
Load Factor for Lateral Loads= 1.0
Loads Supported by Pile Cap= 0 %
Shear Condition: Static

(with Load Factor)


Vertical Load, Q= 111.2 -kN
Shear Load, P= 0.0 -kN
Moment, M= 0.0 -kN-m

Profile:
Pile Length, L= 10.0 -m
Top Height, H= 0.000 -m
Slope Angle, As= 0.0
Batter Angle, Ab= 8.5

Micropile (MiniPile)

Soil Data: Pile Data:


Depth Gamma Phi C K e50 or Dr Nspt Depth Width Area Per. I E Weight
-m -kN/m3 -kN/m2 -MN/m3 % -m -cm -cm2 -cm -cm4 -MPa -kN/m
0 18.078 33.1 0.000 12.404 35.04 10 0.0 15 54.8 47.1 1301.9 199938 0.420
2.134 20.279 0.0 58.892 82.488 0.88 10 4.6 17 377.4 55.9 5058.7 20683 0.665
4.572 8.677 34.2 0.000 11.563 41.10 13 10.0
6.706 10.988 32.5 54.104 192.281 0.61 18
9.144 9.275 36.5 0.000 18.322 54.06 20

Single Pile Lateral Analysis:


Top Deflection, yt= 0.00747-cm
Max. Moment, M= 0.12-kN-m
Top Deflection Slope, St= -0.00007
OK! Top Deflection, 0.0075-cm is less than the Allowable Deflection= 2.50-cm

Note: If the program cannot find a result or the result exceeds the upper limit. The result will be displayed as 99999.
The Max. Moment calculated by program is an internal force from the applied load conditions. Structural engineer has to check whether
the pile has enough capacity to resist the moment with adequate factor of safety. If not, the pile may fail under the load conditions.

CivilTech Micropile with Pressure Grout


Software Two Sections. No Friction on top section
ALL-PILE CivilTech Software www.civiltech.com Licensed to

PILE DEFLECTION & FORCE vs DEPTH


Single Pile, Khead=1, Kbc=1

Depth (Zp) DEFLECTION, yt -cm MOMENT -kN-m SHEAR -kN Depth (Zp)
from from
Pile Top-m -0.01 0 +0.01 -0 0 +0 -0 0 +0 G-kN/m3 Phi C-kN/m2 k-MN/m3e50 % Pile Top-m
0 0
18.078 33.1 0.000 12.404
Medium dense silty SAND

1 1

yt=0 at 1.9-m
2 2
St=0 at 2.3-m 20.279 0.0 58.892 82.488 0.88
Soft Clay
3 3

4 4

8.677 34.2 0.000 11.563


5 Medium dense fine SAND 5

6 6

7 10.988 32.5 54.104 192.281 0.61 7


Very stiff sandy SILT

8 8

9 9
9.275 36.5 0.000 18.322
Medium dense gravelly SAND
10 10
Tip yt=2.48E-14 Top yt=7.47E-3 Top Moment=0.0 Top Shear=0.2
Max. yt=7.47E-3 Max. Moment=0.1 Max. Shear=0.2 Last Section: E -MPa=20683
Top St=-6.8E-5 Last Section: I'-cm4=523
11 11

12 12

13 13

14 14

15 15

CivilTech Micropile with Pressure Grout


Software Two Sections. No Friction on top section5.0
ALL-PILE CivilTech Software www.civiltech.com Licensed to

PILE DEFLECTION vs LOADING


Single Pile, Khead=1, Kbc=1

Depth (Zp) DEFLECTION, yt -cm Depth (Zp)


from from
Pile Top-m -0.01 0 +0.01 Pile Top-m
0 0

1 1

2 2

3 3

4 4

5 5

6 6

7 7

8 8

9 9

10 10

11 11

12 12
Lateral Moment Axial yt Slope Max.
No. Load Load Load at Top at Top Moment
13 (kN) (kN-m) (kN) (cm) (cm/cm) (kN-m) 13
1 0.0 0.0 111.0 0.0 0.00 0.0
2 0.1 0.0 111.0 0.0 0.00 0.0
14 3 0.1 0.0 111.0 0.0 0.00 0.1 14
4 0.1 0.0 111.0 0.0 0.00 0.1
5 0.2 0.0 111.0 0.0 0.00 0.1
15 6 0.2 0.0 111.0 0.0 0.00 0.1 15
7 0.2 0.0 111.0 0.0 0.00 0.1

CivilTech Micropile with Pressure Grout


Software Two Sections. No Friction on top section5.0
ALL-PILE CivilTech Software www.civiltech.com Licensed to

PILE MOMENT vs LOADING


Single Pile, Khead=1, Kbc=1

Depth (Zp) MOMENT -kN-m Depth (Zp)


from from
Pile Top-m -0.20 0 +0.20 Pile Top-m
0 0

1 1

2 2

3 3

4 4

5 5

6 6

7 7

8 8

9 9

10 10

11 11

12 12
Lateral Moment Axial yt Slope Max.
No. Load Load Load at Top at Top Moment
13 (kN) (kN-m) (kN) (cm) (cm/cm) (kN-m) 13
1 0.0 0.0 111.0 0.0 0.00 0.0
2 0.1 0.0 111.0 0.0 0.00 0.0
14 3 0.1 0.0 111.0 0.0 0.00 0.1 14
4 0.1 0.0 111.0 0.0 0.00 0.1
5 0.2 0.0 111.0 0.0 0.00 0.1
15 6 0.2 0.0 111.0 0.0 0.00 0.1 15
7 0.2 0.0 111.0 0.0 0.00 0.1

CivilTech Micropile with Pressure Grout


Software Two Sections. No Friction on top section5.0
ALL-PILE CivilTech Software www.civiltech.com Licensed to

ULTIMATE CAPACITY vs FOUNDATION DEPTH

800 800

720 720

640 640

560 560
Compression Capacity, Qdw -kN

Uplift Capacity, Qup -kN


480 480

400 400

320 320

240 240

160 160

80 80

0 0
0 2 4 6 8 10 12 14 16 18 20 0 2 4 6 8 10 12 14 16 18 20

Foundation Depth, L -m Foundation Depth, L -m

CivilTech Micropile with Pressure Grout


Software Two Sections. No Friction on top sectionFigure 1

You might also like