Lupolen 5121 A

Polyethylene, High Density

Product Description
Lupolen 5121 A is a high molecular weight high density polyethylene (HDPE) resin used in blow
molding applications. Typical customer applications include packagings for dangerous goods and
consumer goods. It exhibits high rigidity and ESCR as well as good flowability and organoleptic
properties. Lupolen 5121 A is delivered in pellet form, contains antioxidants and has a broad
molecular weight distribution.

Lupolen 5121 A is not intended for use in medical and pharmaceutical applications.

Product Characteristics

Status Commercial: Active

Test Method used ISO  

Availability Europe, Asia-Pacific, Australia/NZ, Africa-Middle East,

Latin America

Processing Methods Extrusion Blow Molding

Features Antioxidant, Good Chemical Resistance, High ESCR

(Environmental Stress Cracking Resistance), High Impact
Resistance , Good Processability

Typical Customer Applications Consumer Packaging, Jerry Cans

Typical Properties Method Value Unit

Physical
Density ISO 1183 0.951 g/cm³
Bulk density ISO 60 >0.500 g/cm³
Melt flow rate (190°21,6) ISO 1133 5.0 g/10 min
FNCT (3.5 MPa, 2% Arkopal N100, 80°C) ISO 16770 16 h
Mechanical
Tensile Modulus ISO 527-1, -2 1050 MPa
Tensile Stress at Yield ISO 527-1, -2 25.0 MPa
Tensile Strain at Yield ISO 527-1, -2 7.0 %
Tensile Impact Strength ISO 8256 150 kJ/m²
  Note: Notched, type 1, method A, -30 °C
Thermal
Melting Temperature ISO 3146 131 °C

Additional Properties
Recommended processing temperature: 180 - 220°C

Notes
Typical properties; not to be construed as specifications.

Further Information
Lupolen 5121 A

Conveying: Conveying equipment should be designed to prevent production and accumulation of

fines and dust particles that are contained in polymer resins. These particles can under certain
conditions pose an explosion hazard. We recommend the conveying system used is equipped with
adequate filters, is operated and maintained that no leak develops and adequate grounding exists
at all times.

Health and Safety:

The resin is manufactured to the highest standards but, special requirements apply to certain
applications such as food end-use contact. For specific information on regulatory compliance
contact your local representative.

Workers should be protected from the possibility of skin or eye contact with molten polymer.
Safety glasses are suggested as a minimal precaution to prevent mechanical or thermal injury to
the eyes.

Molten polymer may be degraded if it is exposed to air during any of the processing and off-line
operations. The products of degradation have an unpleasant odour. In higher concentrations they
may cause irritation of the mucus membranes. Fabrication areas should be ventilated to carry
away fumes or vapours. Legislation on the control of emissions and pollution prevention must be
observed. If the principles of sound manufacturing practice are adhered to and the place of work
is well ventilated, no health hazards are involved in processing the resin.

The resin will burn when supplied with excess heat and oxygen. It should be handled and stored
away from contact with direct flames and/or ignition sources. In burning the resin contributes
high heat and may generate a dense black smoke. Starting fires can be extinguished by water,
developped fires should be extinguished by heavy foams forming an aqueous or polymeric film.
For further information about safety in handling and processing please refer to the Material Safety
Data Sheet.

Storage:
The resin is packed in 25 kg bags or in bulk containers protecting it from contamination. If it is
stored under adverse conditions, i. e. if there are large fluctuations in ambient temperature and
the atmospheric humidity is high, moisture may condense inside the packaging. Under these
circumstances, it is recommended to dry the resin before use. Unfavourable storage conditions
may also intensify the resin´s slight characteristic odour.

The resin is subjected to degradation by ultra-violet radiations or by high storage temperatures.

Therefore the resin must be protected from direct sunlight, temperatures above 40°C and high
atmospheric humidity during storage. The resin can be stored over a period of more than 6
month without significant changes in the specified properties, appropriate storage conditions
provided. Higher storage temperatures reduce the storage time.

The information submitted is based on our current knowledge and experience. In view of the
many factors that may affect processing and application, these data do not relieve processors of
the responsibility of carrying out their own tests and experiments; neither do they imply any
legally binding assurance of certain properties or of suitability for a specific purpose. The data do
not relieve the customer from his obligation to control the resin upon arrival and to complain
about faults. It is the responsibility of those to whom we supply our products to ensure that any
proprietary rights and existing laws and legislation are observed.

© LyondellBasell Industries Holdings, B.V. 2015

LyondellBasell markets this product through the following entities:

Equistar Chemicals, LP
Basell Sales & Marketing Company B.V.
Basell Asia Pacific Limited
Basell International Trading FZE
LyondellBasell Australia Pty Ltd

For the contact details of the LyondellBasell company selling this product in your country, please visit
http://www.lyb.com/.

Before using a product sold by a company of the LyondellBasell family of companies, users should make
their own independent determination that the product is suitable for the intended use and can be used
safely and legally. SELLER MAKES NO WARRANTY; EXPRESS OR IMPLIED (INCLUDING ANY WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY WARRANTY) OTHER THAN AS
SEPARATELY AGREED TO BY THE PARTIES IN A CONTRACT.

This product(s) may not be used in:

(i) any U.S. FDA Class I, Health Canada Class I, and/or European Union Class I Medical Devices, without
prior notification to Seller for each specific product and application; or

(ii) the manufacture of any of the following, without prior written approval by Seller for each specific
product and application: (1) U.S. FDA Class II, Health Canada Class II or Class III, and/or European
Union Class II Medical Devices; (2) film, overwrap and/or product packaging that is considered a part or
component of one of the aforementioned Medical Devices; (3) packaging in direct contact with a
pharmaceutical active ingredient and/or dosage form that is intended for inhalation, injection,
intravenous, nasal, ophthalmic (eye), digestive, or topical (skin) administration; (4) tobacco related
products and applications; (5) electronic cigarettes and similar devices; and (6) pressure pipe or fittings
that are considered a part or component of a nuclear reactor.

(iii) Additionally, the product(s) may not be used in: (1) U.S. FDA Class III, Health Canada Class IV,
and/or European Class III Medical Devices; (2) applications involving permanent implantation into the
body; (3) life-sustaining medical applications; and (4) lead, asbestos or MTBE related applications.

All references to U.S. FDA, Health Canada, and European Union regulations include another country's
equivalent regulatory classification.

Users should review the applicable Safety Data Sheet before handling the product.

Adflex, Adstif, Adsyl, Akoafloor, Akoalit, Alastian, Alathon, Alkylate, Amazing Chemistry, Aquamarine,
Aquathene, Arctic Plus, Arctic Shield, Avant, Catalloy, Clyrell, CRP, Crystex, Dexflex, Duopac, Duoprime,
Explore & Experiment, Filmex, Flexathene, Fueling the power to win, Glacido, Hifax, Hiflex, Histif,
Hostacom, Hostalen PP, Hostalen ACP, Ideal, Indure, Integrate, Koattro, LIPP, Lucalen, Luflexen,
Lupolen, Lupolex, Luposim, Lupostress, Lupotech, Metocene, Microthene, Moplen, MPDIOL, Nerolex,
Nexprene, Petrothene, Plexar, Polymeg, Pristene, Prodflex, Pro-fax, Punctilious, Purell, Refax, SAA100,
SAA101, Sequel, Softell, Spherilene, Spheripol, Spherizone, Starflex, Stretchene, Superflex, TBAc ,
Tebol, T-Hydro, Toppyl, Trans4m, Tufflo, Ultrathene, Vacido and Valtec, are trademarks owned and/or
used by the LyondellBasell family of companies.

Adsyl, Akoafloor, Akoalit, Alastian, Alathon, Aquamarine, Arctic Plus, Arctic Shield, Avant, CRP, Crystex,
Dexflex, Duopac, Duoprime, Explore & Experiment, Filmex, Flexathene, Hifax, Hostacom, Hostalen,
Ideal, Integrate, Koattro, Lucalen, Lupolen, Metocene, Microthene, Moplen, MPDIOL, Nexprene,
Petrothene, Plexar, Polymeg, Pristene, Pro-fax, Punctilious, Purell, Sequel, Softell, Spheripol, Spherizone,
Starflex, Tebol, T-Hydro, Toppyl, Tufflo, Ultrathene are registered in the U.S. Patent and Trademark
Office.

Release Date: 15 Jan 2014