4K/UHD High Luminance HDR Emulation LCD Monitor: LUM-181H LUM-181G LUM-242H LUM-242G LUM-328G LUM-550H

Download as pdf or txt
Download as pdf or txt
You are on page 1of 44

4K/UHD High Luminance

HDR Emulation LCD Monitor


# Operation manual_V1.2

LUM-181H
LUM-181G
LUM-242H
LUM-242G
LUM-328G
LUM-550H
FCC (Federal Communications Commission)
This equipment has been tested and found to comply with the limits for class A digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interface when the equipment is operated in a commercial environment.
This equipment generates, uses and can radiate radio frequency energy and if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential to correct the interference at his own expense
CAUTION: Change or modifications not expressly approved by the manufacturer responsible for
compliance could void the
user’s authority to operate the equipment.

Disposal of Old Electrical & Electronic Equipment


(Applicable in the European Union and other European countries with separate collection systems)
This symbol on the product or on its packing indicates that this product shall not be treated as
household waste.
Instead it shall be handed over to the applicable collection point for the recycling of electrical and
electronic equipment.
By ensuring this product is disposed of correctly, you will help prevent potential negative consequence
for the environment and human health, which could otherwise be caused by inappropriate waste
handling of this product. The recycling of materials will help to conserve
natural resources.
Contents

01 CAUTION 04p

02 MAIN FEATURES 08p

03 CONTROLS & FUNCTIONS 09p

04 MENU ORGANIZATION & ADJUSTMENT 18p

05 MENU OPERATIONS 21p

[1] PICTURE & VIDEO 21p


[2] COLOR 23p
[3] GPI 25p
[4] MARKER 27p
[5] WAVEFORM & FOCUS 29p
[6] AUDIO 31p
[7] DISPLAY & SET 33p
[8] INFORM 35p

06 VIDEO SUPPORT RESOLUTION 36p

07 PRODUCT SPECIFICATIONS 38p


4K /UHD HDR Emulation LCD Monitor

01 CAUTION
●● Always use set voltage. • If any of the following conditions occurs,
unplug the power cord from the AC outlet,
LUM-181H and request a qualified service person to
- AC 100 ~ 240V (50~60Hz) perform repairs.
- DC 12V/8A ~ 24V/4A a. When the power cord or plug in damaged.
b. When a liquid was spilled on the product or
LUM-242H when objects have fallen into the product.
- AC 100 ~ 240V (50~60Hz) c. When the product has been exposed to rain
- DC 24V/6.5A or water.
d. When the product does not operate properly
• All operating instructions must be read and as described in the operating instructions.
understood before the product is operated. Do not touch the controls other than those
described in the operating instructions.
• These safety and operating instructions must Improper adjustment of controls not
be kept in safe place for future reference. described in the instructions can cause
damage, which often requires extensive
• All warnings on the product and in the adjustment work by a qualified technician.
instructions must be observed closely. e. When the product has been dropped or
damaged.
• All operating instructions must be followed. f. When the product displays an abnormal
condition. Any noticeable abnormality in
• Do not use attachments not recommended the product indicates that the product
by the manufacturer. Use of inadequate needs servicing.
attachments can result in accidents.
• In case the product needs replacement parts,
• This product must be operated on a power make sure that the service person uses
source specified on the specification label. replacement parts specified by the
If you are not sure of the type of power supply manufacturer, or those with the same
used in your home, consult your dealer or local characteristics and performance as the original
power company. For units designed to operate parts. Use of unauthorized parts can result in
on batteries or another power source, refer to fire, electric shock and/or other danger.
the operating instructions.
• Upon completion of service or repair work,
• The power cords must be routed properly request the service technician to perform safety
to prevent people from stepping on them or checks to ensure that the product is in proper
objects from resting on them. Check the cords operating condition.
at the plugs and product.
• The power cord plug shall be connected to a
• Do not overload AC outlets or extension cords. main socket outlet with a protective earthing
Overloading can cause fire or electric shock. connection.

• Never insert an object into the product • Unplug the power cord from the AC outlet
through vents or openings. High voltage flows when happening any problem in the product.
in the product, and inserting an object can
cause electric shock and/or short internal parts. • When mounting the product on a wall or
For the same reason, do not spill water or liquid ceiling, be sure to install the product
on the product. according to the method recommended by the
manufacturer.
• Do not attempt to service the product yourself.
Removing covers can expose you to high
voltage and other dangerous conditions.
Request a qualified service person to perform
servicing.

4
4K /UHD HDR Emulation LCD Monitor

01 CAUTION
• Unplug the power cord from the AC outlet • The vents and other openings in the cabinet
before cleaning the product. Use a damp cloth are designed for ventilation. Do not cover or
to clean the product. Do not use liquid cleaners block these vents and openings since
or aerosol cleaners. insufficient ventilation can cause overheating
and/or shorten the life of the product. Do not
• Unplug the power cord from the AC outlet if place the product on a bed, sofa, rug or other
you do not use the product for considerably similar surface, since they can block ventilation
long time. openings. This product is not designed for
built-in installation; do not place the product
• Do not use the product near water, such as in an enclosed place such as a bookcase or
bathtub, washbasin, kitchen sink and laundry rack, unless proper ventilation is provided or
tub, swimming pool and in a wet basement. the manufacturer’s instructions are followed.
• Keep the product away from direct rays of the • The LCD panel used in this product is made of
Sun-light. glass. Therefore, it can break when the product
is dropped or applied with impact. Be careful
• Do not place the product on an unstable cart, not to be injured by broken glass pieces in case
stand, tripod or table. Placing the product on the LCD panel breaks.
an unstable base can cause the product to fall,
resulting in serious personal injuries as well as • Keep the product away from heat sources
damage to the product. Use only a cart, stand, such as radiators, heaters, stoves and other heat
tripod, bracket or table recommended by the generating products (including amplifiers).
manufacturer or sold with the product. When
mounting the product on a wall, be sure to • If the still image is displayed on the screen in
follow the manufacturer’s instruction. Use only the same position for a long period of time, the
the mounting hardware recommended by the permanent burn-in on the LCD panel may occur.
manufacturer. So, do not display characters or markers
continuously.
• Infrared devices can cause noise or malfunction If the video signals or image patterns are
under condition as below. continuously displayed at the maximum or high
- Parts of the body come into contact with the level of luminance, the image smearing or flicker
infrared transmiter or acoustic device. may occur on the screen because of the LCD
- Obstacles can cause electrical changes if there panel’s structure and characteristics of materials
is a partition in the middle or in the wall. used.
- Exposure to radio interference from medical When the permanent burn-in, image smearing,
equipment, microwave ovens, wireless LAN or other damages happen on the LCD panel
devices, etc. with the same frequency band. due to the improper use by the end user,
the warranty service is not applied.
• When relocating the product placed on a cart,
it must be moved with the utmost care.
Sudden stops, excessive force and uneven floor
surface can cause the product to fall from the
cart.

5
4K /UHD HDR Emulation LCD Monitor

01 CAUTION
VESA WALL MOUNTING

6
4K /UHD HDR Emulation LCD Monitor

01 CAUTION
VESA WALL MOUNTING

• When mounting on the wall bracket, fix the monitor using 4 pieces of M4 x 10mm screws.

• Use the 100mm x 100mm VESA MOUNTING holes on the rear housing.

• Do not install on a place other than a vertical wall.

• Do not use screws longer then the standard dimension, as they may cause damage to the
inside to the monitor.

• Do not tighten the screws too much. It may damage the monitor or make the monitor fall
and cause personal injury. Vidente(TVLogic) is not liable for these kinds of accidents.

• Remove the stand before installing the monitor on the wall using the wall mount kit.

• Do not install your wall mount kit while the monitor is plugged in.
It may result in personal injury due to electric shock.

7
4K /UHD HDR Emulation LCD Monitor

02 MAIN FEATURES
LUM-181H / 181G / 242H / 242G / 328G / 550H Monitor contains the following features:

●● Compatible with various SDI signal ●● Ethernet & USB support


formats - Supports the Ethernet connection for
- This product is compatible with various SDI monitor control and the USB connection
signals. - 720P, 1080p, 2160p for firmware update and color calibration.

●● Compatible with various Digital signal ●● HDMI(2.0) support


formats - 1 x HDMI(2.0) input is available without
- This product is compatible with various HDMI additional equipment.
Digital signals- 50p, 59.94p, 60p.
●● SDI 3G support
●● 4K(SMPTE ST 428-1-2006 : 4096 x2160 - Supports 3G-SDI YCbCr/RGB 4:4:4 and YCbCr
@24p /SMPTE ST 2036-1:2009 : 3840x2160 4:2:2 formats.
@23.98p ~ 60p) Support
- 6G/ 12G is supported only in SDI A, SDI B ●● Additional features
modes. - Wide Viewing Angle, Active Loop
Through(SDI), VESA Mounting Standard and
●● Advanced Cooling System by adopting OSD user interface.
the Premium Quality Quite Fan * Max. Brightness 1000cd/m2
- The fans inside the monitor are designed
to rotate at the maximum speed in order ●● Various Color Gamut support
to lower the internal tmeperature of the monitor - ITU-R BT.709, BT.2020, DCI-P3(color standard
displaying the high-luminance content. of digital cinema), SGamut3, Panel Native.
- With the adoption of the premium quality fans
featuring sophisticated aerodynamic design,
advanced acoustic optimisation, anti-vibration
pads, both the improved cooling performance
and the quite monitoring environment are
achieved.

●● Remote control function


- This product can simply be remote
controlled by using parallel switch.

●● RS422 protocol support


- This product supports protocols provided by
TVLogic.

8
4K /UHD HDR Emulation LCD Monitor

03 CONTROLS & FUNCTIONS


LUM-181H: FRONT

MENU/EXIT
F5 ENTER
F4 LED (POWER INDICATOR)
F3 POWER
F2
F1 MENU/EXIT
F5 ENTER
F4 LED (POWER INDICATOR)
F3 POWER
F2
F1

HDMI INFO.
SDI SINGLE VIDEO RANGE
2SI B.LIGHT
QUAD MARKER
ASPECT
HDMI INFO.
SCAN
SDI SINGLE VIDEO RANGE
2SI B.LIGHT
QUAD MARKER
LUM-181H : REAR ASPECT
SCAN

RS-422 IN
RS-422 OUT

RS-422 IN
RS-422 OUT

DC IN SDI-IN (A~D)
AC IN SDI-OUT (A~D)

DC IN SDI-IN (A~D)
HDMI
AC IN SDI-OUT (A~D)
REMOTE
LAN
AUDIO-IN

HDMI
REMOTE
LAN
AUDIO-IN

9
4K /UHD HDR Emulation LCD Monitor

03 CONTROLS & FUNCTIONS


LUM-181G: FRONT

MENU/EXIT
F5 MENU/EXIT
F5 ENTER
F4 ENTER
F4 LED (POWER INDICATOR)
F3 LED (POWER INDICATOR)
F3 POWER
F2 POWER
F2
F1
F1

HDMI INFO.
HDMI
SDI SINGLE INFO.RANGE
VIDEO
SDI SINGLE 2SI VIDEO RANGE
B.LIGHT
QUAD
2SI MARKER
B.LIGHT
QUAD ASPECT
MARKER
SCAN
ASPECT
SCAN

LUM-181G : REAR

RS-422 IN
RS-422 OUT
RS-422 IN
RS-422 OUT

DC IN SDI-IN (A~D)
AC IN SDI-OUT (A~D)
DC IN SDI-IN (A~D)
AC IN SDI-OUT (A~D)

HDMI
REMOTE
LAN
HDMI
AUDIO-IN
REMOTE
LAN
AUDIO-IN

10
4K /UHD HDR Emulation LCD Monitor

03 CONTROLS & FUNCTIONS


LUM-242H: FRONT

MENU/EXIT
F5 ENTER
F4 LED (POWER INDICATOR)
F3 MENU/EXIT
POWER
F5
F2 ENTER
AUDIO OUT
F4
F1 LED
USB (POWER INDICATOR)
F3 POWER
F2 AUDIO OUT
F1 USB

HDMI INFO.
SDI SINGLE VIDEO RANGE
2SI B.LIGHT
HDMI
QUAD INFO.
MARKER
SDI SINGLE VIDEO
ASPECTRANGE
2SI B.LIGHT
SCAN
QUAD MARKER
ASPECT
LUM-242H : REAR SCAN

RS-422 IN
RS-422 OUT

AC IN
RS-422 IN
DC IN RS-422 OUT

AC IN
DC IN SDI-IN (A~D)
SDI-OUT (A~D)

SDI-IN (A~D)
SDI-OUT (A~D)
HDMI
REMOTE
LAN
HDMI
AUDIO-IN
REMOTE
LAN
AUDIO-IN

11
4K /UHD HDR Emulation LCD Monitor

03 CONTROLS & FUNCTIONS


LUM-242G: FRONT

MENU/EXIT
F5 ENTER
MENU/EXIT
F4
F5 LED
ENTER
F3
F4 POWER
LED
F2
F3 AUDIO OUT
POWER
F1
F2 USB
AUDIO OUT
F1 USB

HDMI INFO.
SDI SINGLE
HDMI VIDEO RANGE
INFO.
2 SDI
SDI SINGLE B.LIGHT
VIDEO RANGE
QUAD
2 SDI MARKER
B.LIGHT
QUAD ASPECT
MARKER
SCAN
ASPECT
SCAN
LUM-242G : REAR

DC OUT
RS-422
DC OUTIN
RS-422
RS-422 OUT
IN
RS-422 OUT

SDI-IN (A~D)
SDI-OUT (A~D)
SDI-IN (A~D)
SDI-OUT (A~D)
DC IN
AC IN
DC IN
AC IN

HDMI
REMOTE
HDMI
LAN
REMOTE
AUDIO-IN
LAN
AUDIO-IN

12
4K /UHD HDR Emulation LCD Monitor

03 CONTROLS & FUNCTIONS


LUM-328G: FRONT

MENU/EXIT
HLG ENTER
MENU/EXIT
PQHLG LEDENTER
(POWER INDICATOR)
DCI PQ POWER
LED (POWER INDICATOR)
UHDDCI AUDIO OUT
POWER
HDUHD USBAUDIO OUT
HD USB

HDMI INFO.
SDI SINGLE
HDMI ASPECT
INFO.
2SI
SDI SINGLE SCAN
ASPECT
QUAD 2SI VIDEO RANGE
SCAN
QUAD WFMVIDEO RANGE
MARKER
WFM
MARKER

LUM-328G : REAR

RS-422 IN
RS-422 OUTIN
RS-422
RS-422 OUT

AC IN SDI-IN (A~D)
AC IN SDI-OUT
SDI-IN(A~D)
(A~D)
SDI-OUT (A~D)

HDMI
REMOTE
HDMI
LANREMOTE
AUDIO-IN
LAN
AUDIO-IN

13
4K /UHD HDR Emulation LCD Monitor

03 CONTROLS & FUNCTIONS


LUM-55OH: FRONT

MENU/EXIT
ENTER
F5
LED (POWER INDICATOR)
F4
POWER
F3
AUDIO OUT
F2
MENU/EXIT
USB
F1
ENTER
F5
LED (POWER INDICATOR)
F4
POWER
F3
AUDIO OUT
F2
USB
F1 HDMI INFO.
SDI SINGLE VIDEO RANGE
2SI B.LIGHT
QUAD MARKER
ASPECT
HDMI INFO.
SCAN
SDI SINGLE VIDEO RANGE
2SI B.LIGHT
QUAD MARKER

LUM-55OH : REAR ASPECT


SCAN

RS-422 IN
RS-422 OUT

AC IN

SDI-IN (A~D)
RS-422 IN(A~D)
SDI-OUT
RS-422 OUT

AC IN

SDI-IN (A~D)
SDI-OUT (A~D)

HDMI
REMOTE
LAN
AUDIO-IN

HDMI
REMOTE
LAN
AUDIO-IN

14
4K /UHD HDR Emulation LCD Monitor

03 CONTROLS & FUNCTIONS


LUM-181H / 181G / 242H / 242G / 328G / 550H : FRONT

●● [HDMI] Button/Lamp
- Used to select HDMI input. 6) Luma(Y') Zone
- Refer to the page 24.
●● [SINGLE] Button/Lamp
- Used to select SDI input for one channel. 7) Focus Assist
Previously selected SDI input selection - Refer to the page 25.
displays. 8) Marker
- Press the button to move through the modes: - Refer to the page 21.
SDI-A → SDI-B → SDI-C → SDI-D
9) DR Mode
●● [2SI] Button/Lamp - Used to select the dynamic range mode in
- Used to select the SDI 2-Sample Interleave the order of SDR → HDR → User.
input signal(quad link or dual link). - SDR : Standard Dynamic Range Mode
- Press the button to move through the modes - HDR : High Dynamic Range Mode
: 2SI(4CH) → 2SI(2CH) - User : Custom Dynamic Range Mode

●● [QUAD] Button/Lamp 10) Standard


- Used to select the SDI Quad link square - Refer to the page 16.
division input signal. 11) Disp Luminance
- Refer to the page 16.
●● [F1 ~ F5] Button/Lamp
- Shortcut key for KEY MAPPING feature in the 12) EOTF
OSD MENU. - Refer to the page 16.
- Selectable function are as follows :
13) Video Range
1) Blue Only - Refer to the page 16.
- Activates in the order of [Blue Only] → [Mono]
14) Waveform
→ [Off]. - Refer to the page 23.
- Blue Only: Used to remove red and green
from the input signal and display the screen 15) Scan
only under a blue signal. - Refer to the page 10.
- Mono: Used to remove all colors from the
16) Aspect
input signal and display the screen only - Refer to the page 10.
under white and black signal.
17) Native Mode
2) H/V Delay - Used to display the original colors of the
- Used to check horizontal and vertical sync LCD panel.
simultaneously by moving the screen up/
down/left/right. 18) Gumat Warning
- Refer to the page 17.
3) White Point
- This function activates when [Standard] - 19) Shadow Mode
[User1/2/3/4/5/6] is selected. - To be supported.
- Refer to the page 16. 20) 4K Align
4) Audio Level Meter - Refer to the page 15.
- Refer to the page 26.
5) Time Code
- Refer to the page 27.

15
4K /UHD HDR Emulation LCD Monitor

03 CONTROLS & FUNCTIONS


LUM-181H / 181G / 242H / 242G / 328G / 550H : FRONT

●● [SCAN] Button ●● [MENU/EXIT] Button


- Used to select [Zero Scan] and [Over Scan]. - Used to activate/deactivate the OSD menu.
- Press the MENU button again to deactivate
●● [ASPECT] Button the OSD menu.
- Used to select ASPECT mode.
- Available aspect modes are [FULL], [4:3], ●● [UP/DOWN/ENTER] Knob
[2.35:1], [1.85:1], [15:9], [16:9], [16:10], - Used to move up/down through the menus
[AUTO]. during the OSD menu activation and also to
increase/decrease the value of the selected
●● [MARKER] Button feature.
- Used to activate/deactivate the Marker. - Press the Knob to confirm a chosen value
(or mode).
●● [B. LIGHT] Button - May also be used to control the [Backlight] -
- Used to adjust the backlight level. [Brightness] - [Contrast] - [Volume] value
- Turn the ENTER knob left or right to adjust during
the value. the OSD menu inactivation. Turn the Knob to
the left/right to adjust the value.
●● [VIDEO RANGE] Button
- Used to select the video range. ●● [POWER INDICATOR] Lamp
- Available modes are [Narrow 100%], - Indicates condition and power status of unit.
[Narrow 109%], [SDI Full]. - Light turns off when the power is disconnected.
- This function activates when [Standard] - - Standby mode is indicated by a red LED light.
[User1/2/3/4/5/6] is selected. - Normal (active) mode is indicated by a
Green LED light.
●● [INFO.] Button - The Green light turns off when the monitor
- Used to activate the information window. is Normal(active) mode without input signal.
- Refer to the page 29 for the details.
●● [POWER] Button
- Used to turn the power on and off.

- Hold the Power button for 3 seconds to


turn off the unit. This is to prevent the unit
from being turned off by touching the Power
button by accident.

●● [Audio out] (PHONE JACK)


- Selects the left/right Audio embedded signal
output.

●● [USB]
- Used to update the new firmware.
- Used to calibrate the monitor’s color
temperature using color calibration tool.

16
4K /UHD HDR Emulation LCD Monitor

03 CONTROLS & FUNCTIONS


LUM-181H / 181G / 242H / 242G / 328G / 550H : REAR

●● [REMOTE] (RJ-45) ●● [AUDIO IN]


- Provides connection to control - Used to connect the audio input signal.
equipment(parallel switch) for external
monitor control. ●● [LAN]
- Features can be changed in the GPI section of - Used to control the monitor with a protocol
the OSD menu. provided by TVLogic.

●● [RS422 IN/OUT] (RJ-45) ●● [AC IN]


- Used to control the monitor with a protocol - LUM-181H: 100~240V (50/60Hz)
provided by TVLogic. - LUM-242H: 100~240V (50/60Hz)

●● [HDMI] ●● [DC IN]


- Signal input terminal for HDMI signal. - LUM-181H: DC 12V/8A ~ 24V/4A
- LUM-242H: DC 24V/6.5A
●● [SDI-A/B/C/D] (BNC)
- SDI signal input terminal.
<WARNING!!>
- SDI-A/B support 12G/6G/3G/HD-SDI input. When using the product make sure to ground,
- SDI-C/D support 3G/HD-SDI input. whenever possible, before connecting the
input signal cable in order to prevent any
●● [SDI-A/B/C/D Output] (BNC) possible damage to the product or connected
- SDI signal loop-out terminal. devices. The damage may include signal noise,
- SDI-A/B support 12G/6G/3G/HD-SDI output. malfunction of main board or display panel.
- SDI-C/D support 3G/HD-SDI output. And the connected devices such as camera or
video source player may also be influenced
* SDI Output is not activated when the through signal cable. Please check if the AC
power source and the power extender or
unit is turned off or in Standby mode. power distributor is grounded.

17
4K /UHD HDR Emulation LCD Monitor

04 MENU ORGANIZATION & ADJUSTMENT


[1] Menu Organization [3] Menu Adjustment Procedure

●● The product may be controlled and set by ●● Menu control sequence follows the order
OSD display on the screen. below:

1. Press the MENU button to activate the OSD


menu.

2. Move to a desired menu by turning the


KNOB to the left/right.

3. Press the KNOB button to select a menu and


move to a sub-menu by turning the KNOB
to the left/right.

4. Press the KNOB button to select the desired


sub-menu. (The selected sub-menu’s font
color will be highlighted.)

5. Press the KNOB or MENU button to save the


new value after adjusting the value with the
KNOB button. (The changed font color will
[2] Menu Adjustment be returned to default.)

●● You may control various functions 6. Press the MENU button to return to the
using MENU, UP/DOWN and ENTER previous menu and if there is no previous
buttons on the bottom of the monitor. menu, the OSD menu will be removed from
the screen.

18
4. Menu Organization & Adjustment 4K /UHD HDR Emulation LCD Monitor

04 MENU ORGANIZATION & ADJUSTMENT


[4] Menu Tree

Brightness PIN1~PIN8
Contrast Monitor ID
Chroma DHCP
PICTURE Aperture IP Address
& VIDEO
Aspect Subnet Mask
3G Format Gateway
4K Align GPI Port NO.
Standard Network settings apply
Video Range UMD Display
Disp Luminance UMD Character
Black Level UMD character color
EOTF UMD B.G. trans. (*Deactivated)
White Point UMD size
HLG SG Marker
Color Gamut Center Marker
Gamut Warning Safety Area
EETF Fit Marker
COLOR
Gain / Offset Marker Mat
Reset MARKER Marker Color
Gain / Offset Thickness
Gain Red User Marker H1
Gain Green User Marker H2
Gain Blue User Marker V1
Bias Red User Marker V2
Bias Green
Bias Blue
Color Copy

19
4K /UHD HDR Emulation LCD Monitor

04 MENU ORGANIZATION & ADJUSTMENT


[4] Menu Tree

Waveform Display User Config Set


Waveform Intensity Internal Pattern
Waveform Trans. (*Deactivated) System Default
Waveform Color S/W Upgrade
Line Waveform S/W Upgrade Start
Line Select Position Time Code
WAVEFORM Luma(Y’) Zone Check Key Lock
& FOCUS Luma(Y’) Zone Adjust Key LED
Focus Assist Closed Caption
Focus Assist Color DISPLAY Decode Channel(608)
& SET
Focus Assist Level Caption Service(708)
Range Error OSD Position
Y Max Transfer Matrix
Y Min Gamut Control
Level Meter Select [F1] Key Mapping
Level Meter Display [F2] Key Mapping
Level Meter Reference [F3] Key Mapping
Peak Decay Time [F4] Key Mapping
AUDIO
Level Meter Size [F5] Key Mapping
Volume
Em. Audio Left
Em. Audio Right

20
4K /UHD HDR Emulation LCD Monitor

05 MENU OPERATIONS
[1] Picture & Video
●● 4K Align
- When the 4K 4096 x 2160(17:9) signal
is input to the LUM-181H or LUM-242H
whose resolution of the LCD panel is
3840 x 2160(16:0), the following four
modes can be selected.
[Center]: The input image is displayed as pixel to pixel,
and the vertical 128 lines on the left end and right
end are hidden.

3840 x 2160
(Panel)

3840 x 2160
(Panel)

4096 x 2160
(Image)
●●Brightness
- Used to adjust the overall brightness 4096 x 2160
(= Offset) level, which mainly affects (Image)

the black level. The adjustment range is [Right]: The input image is displayed as pixel to pixel.
-100(MIN) to 100(MAX). The right end of the input image is displayed in full,
and the vertical 256 lines on the left are hidden.
●● Contrast 3840 x 2160
- Used to set the contrast(Gain) level from (Panel)
[-100] to [100].
3840 x 2160
●● Chroma (Panel)
- Used to set the saturation level from [-50] 4096 x 2160
to [50]. (Image)

●● Aperture 4096 x 2160


- Used to set the sharpness level from [0] (Image)
to [24]. [Scale]: The input video is scaled to the 16:9 ratio
and displayed in full on the screen.
●● Aspect
3840 x 2160
- Used to change the various display ratio. (Panel)
- Available aspect modes are [FULL], [4:3],
[2.35:1], [1.85:1], [15:9], [16:9], [16:10],
[AUTO].
- Activated only in Single 3G Mode. 4096 x 2160
(Image)

●● 3G Format
- Automatically detects when Payload signal 3840 x 2160
(Image)
appears in Normal Mode.
[Left]: The input image is displayed as pixel to pixel.
- Selects input format for SDI 3G A/B support The left end of the input image is displayed in full,
[NORMAL MODE] and the vertical 256 lines on the right are hidden.

[A 444 10BIT_YCbCr] 3840 x 2160


[A 444 10BIT_RGB] (Panel)

[A 444 12BIT_YCbCr]
3840 x 2160
[A 444 12BIT_RGB] (Panel)
[A 422 12BIT_YCbCr] 4096 x 2160
[B 444 10/12BIT_YCbCr] (Image)
[B 444 10/12BIT_RGB]
[B 422 12BIT_YCbCr] 4096 x 2160 21
(Image)
[B 422 10BIT_YCbCr, 60P]
4K /UHD HDR Emulation LCD Monitor

05 MENU OPERATIONS
[2] Color

LUM-181H ●● Black Level (Not supported)


- The minimum black level of the
Standard HD video signal can be set differently
Video Range Narrow 109% depending on the performance of the
Disp Luminance 100 monitor or the lighting environment.
Black Level Off * Lite : Black level similar to Global Dimming
EOTF 2.4
* Deep : Lowest Black level of the Panel
White Point D65 - Activates only in the Color Standard User
HLG SG Off mode.
Color Gamut B.T.709
●● EOTF (Electro-Optical Transfer Function)
- Electrophotic conversion Functions(ex:
Gamma or HDR curve).
- Available options are [2.2], [2.4], [2.6], [2.8],
●● Standard [BT.1886], [PQ], [HLG], [Native].
- Used to select the color and dynamic range - Activates only in [Standard]-[User] mode.
of the screen.
- Available options are [HD], [UHD], [DCI-P3],
●● White Point
[PQ], [Dolby PQ], [HLG], [User1/2/3/4/5/6].
- Used to select the White Point.
- Available options are [D60], [DCI-White],
●● Video Range [D65], [9300K].
- Used to select the range of digital video
signal.
* [SDI Full] : Input signal 1~254 (8bit), 4~1019 ●● HLG SG (HLG System Gamma)
(10bit) - Used to set the System Gamma of the HLG
* [Narrow 109%] : Input signal Y‘: 16~254, mode.
CbCr: 16~240(8bit) / Y‘: 64~1019, CbCr: 64-1019 - Available options are [0.78 (100nit)],
(10bit) [0.91(200nit)], [0.98 (300nit)], [1.03 (400nit)],
* [Narrow 100%] : Input signal Y‘: 16~235, [1.07 (500nit)], [1.11 (600nit)], [1.13 (700nit)],
CbCr: 16~240(8bit) / Y‘: 64~940, CbCr: 64-960 [1.16 (800nit)], [1.18 (900nit)], [1.2 (1000nit)]
(10bit) and [1.33 (2000nit)] .
- Activates only when [Standard] or [EOTF]
●● Disp Luminance is set to [HLG].
- Used to select the Peak Luminance of the
monitor. ●● Color Gamut
- Selectable levels are [48], [60] ~ [200] with - Used to select the standard color gamut.
10 increment, [200] ~ [1000] with 100 - Available options are [BT.709], [BT.2020],
increment. [DCI-P3], [SGamut3], [Native].
- When [Standard] or [EOTF] is set to [PQ], - Activates only when [Standard] is set to
[Dolby PQ] or [HLG], it is displayed as Void [User] mode.
and it cannot be adjusted.

22
4K /UHD HDR Emulation LCD Monitor

05 MENU OPERATIONS
[2] Color

LUM-181H

Gamut Warning Off

EETF Off
Gain/Offset Default
Reset No

●● Gamut Warning
- Used to display warning when the input
colors exceeds the permissible range of the
panel color gamut.
- Available modes are [OFF] and [ON].

●● EETF (Electrical-Electrical Transfer Function)


- It is a conversion function that expresses
(without clipping) the HDR image within
the actual luminance range (black level
& peak luminance) that the monitor can
express. In case of [ON] mode, the HDR
image is converted within the range of
set peak luminance and black level. If it is
[OFF], the video signals outside the set range
will be clipped.
- Available options are [OFF] and [ON].
- Activates only when [Standard] or [EOTF] is set
to [PQ] or [Dolby PQ].

●● Gain/Offset
- Used to select the Color Temperature that
manually changed by the user.
- Available options are [Default] and [User1/2/3].

●● Reset
- Used to restore the settings that manually
changed by the user to the preset values.
- Only the current selected Color Standard is
applied.

23
4K /UHD HDR Emulation LCD Monitor

05 MENU OPERATIONS
[2] Color

LUM-181H ●● Bias Red


- Used to set Red Bias from [-256] to [255].
Gain/Offset Default - Adjusts the red color of dark section.
Gain Red 0

Gain Green 0 ●● Bias Green


Gain Blue 0
- Used to set Green Bias from [-256] to [255].
- Adjusts the green color of dark section.
Bias Red 0
Bias Green 0
●● Bias Blue
Bias Blue 0 - Used to set Blue Bias from [-256] to [255].
ColorCopy Default - Adjusts the blue color of dark section.

●● Color Copy
- Used to copy the R/G/B Gain value of pre-
stored color temperature settings.
●● Gain/Offset
- Turn the KNOB left/right and press the ENTER
- Used to manually adjust the color and
button to copy and apply the selected color
brightness of the monitor.
temperature value.
- Available options are [Default] and [User1/2/3].

●● Gain Red
- Used to set Red Gain level from [-256] to [255].
- Adjusts the red color of bright section.

●● Gain Green
- Used to set Green Gain level from [-256] to [255].
- Adjusts the green color of bright section.

●● Gain Blue
- Used to set Blue Gain level from [-256] to [255].
- Adjusts the blue color of bright section.

24
4K /UHD HDR Emulation LCD Monitor

05 MENU OPERATIONS
[3] GPI

PIN No. Settable Values

NONE
SINGLE-SDI
2SI-SDI
QUAD-SDI
HDMI
ASPECT
H/V DELAY
●● This item activates/ inactivates the BLUE ONLY
REMOTE function. MONO
16:9 MARKER
●●The user may designate a function for 4:3 MARKER
each pin and each pin’s default setting is 4:3 ON AIR MARKER
as follows. PIN 15:9 MARKER
1~6
14:9 MARKER
●● The default settings are as follows:
PIN 1 : SINGLE-SDI 13:9 MARKER
PIN 2 : 2SI-SDI 1.85:1 MARKER
PIN 3 : QUAD-SDI 2.35:1 MARKER
PIN 4 : HDMI
PIN 5 : ASPECT 1.85:1&4:3 MARKER
PIN 6 : H/V Delay CENTER MARKER
PIN 7 : Power On/Off use only SAFETY AREA 80%
PIN 8 : GND only SAFETY AREA 85%
SAFETY AREA 88%
REMOTE (RJ-45) SAFETY AREA 90%
SAFETY AERA 90%
1: Pin1 1 8 SAFETY AERA 93%
2: Pin2 SAFETY AERA 100%
3: Pin3
4: Pin4
5: Pin5
6: Pin6
7: Pin7
8: GND

25
4K /UHD HDR Emulation LCD Monitor

05 MENU OPERATIONS
[3] GPI

●● Monitor ID ●● UMD Display


- This item sets the ID of each monitor for the - Used to set UMD and ANC.
TVLogic control protocol using RS-422/485 - Available modes are [OFF], [UMD] and [ANC].
communication. * [UMD] : Displays user customized 8 characters
- Available values are [0~127]. on screen.
* [ANC] : Displays characters embedded in SDI
●● DHCP signal.
- Used to activate/deactivate the DHCP
function. ●● UMD Character
- Used to customize the characters for Under
●● IP Address Monitor Display.
- Used to set the IP Address connected to a - Alphabets, numbers and special symbols are
Monitor. available.
- Maximum of 8 characters are available.
●● Subnet Mask
- Used to set the Subnet Mask connected to a ●● UMD character color
Monitor. - Used to set the character color of UMD.
- Available options are [Red], [Green], [Blue],
●● Gateway [Yellow], [Cyan], [Magenta], [White].
- Used to set the Gateway number connected - Activates only when the [D-UMD tally type]
to a Monitor. is set to [Default], [User color], [BG. Color],
[User tally] or [User BG.].
●● Port NO.
- Used to set the port number of the monitor. ●● UMD B.G. trans. (Not supported)
- This function sets the transparency of the
●● Network Settings apply UMD character’s background box.
- Use to apply changed value of IP Address, - Available modes are OPAQUE, 50%, 85% and
Subnet mask, Gateway and Port no. 100%.

●● UMD size
- This function adjusts the size of UMD FONT.
- Available modes are Small and Large.
26
4K /UHD HDR Emulation LCD Monitor

05 MENU OPERATIONS
[4] Marker

●● Fit Marker
- Used to activate or inactivate the FIT
MARKER function.
- When the Marker type is selected in
the Marker menu, a border line of the
Safety Area will be displayed inside the
Marker. Images below show the difference
between Fit Marker [ON] and [OFF].
- FIT MARKER ON/OFF displays as shown below

●● MARKER : 4:3 ●● MARKER : 4:3


●● Marker ●● SAFETY AREA : 90% ●● SAFETY AREA : 90%
- Used to select the marker type when the ●● FIT MARKER : OFF ●● FIT MARKER : ON
MARKER is displayed on the screen.
- MARKER may only be activated by pressing
●● Marker Mat
the MARKER button on the bottom front of - Used to set the darkness level outside of
the monitor. the MARKER area from [OFF](transparent) to
- Available marker types are [Off], [16:9], [4:3], [7](Black).
[4:3] ON AIR, [15:9], [14:9], [13:9], [1.85:1], - The higher the level is, the darker the outside
[2.35:1], [1.85:1 & 4:3], [4:3 ALT 14:9], [16:9 of the MARKER area is.
ALT 14:9], [16:9 ALT 4:3] and [USER].
●● Marker Color
●● Center Marker - Used to control the color of MARKER lines.
- Used to select the availability of the CENTER - Available colors are [White], [Gray], [Black],
MARKER on the screen. [Red], [Green], [Blue], [Dynamic].
- This function operates only after activating
the MARKER function by pressing the ●● Thickness
- The item controls the thickness of the
MARKER button on the bottom front of the MARKER lines.
monitor. - The degrees of thickness are between [1] ~ [7].
●● Safety Area
- Used to select and control the size and
availability of the SAFETY AREA.
- Available types are [80%], [85%], [88%],
[90%], [93%], [100%], [EBU ACTION 16:9],
[EBU GRAPHIC 16:9], [EBU Action 14:9],
[EBU Graphic 14:9], [EBU Action 4:3] and
[EBU GRAPHIC 4:3].
- This function operates only after activating
the MARKER function and by pressing the
MARKER button on the bottom front of the
monitor.

27
4K /UHD HDR Emulation LCD Monitor

05 MENU OPERATIONS
[4] Marker

●● USER Marker H1
- Used to set the position of the first horizontal
marker line.
- Displayed when MARKER menu is set to USER.

●● USER Marker H2
- Used to set the position of the second
horizontal marker line.
- Displayed when MARKER menu is set to USER.

●● USER Marker V1
- The item controls the position of the first
user defined vertical marker line.
- Marker option USER needs to be selected.

●● USER Marker V2
- The item controls the position of the second
user defined vertical marker line.
- Marker option USER needs to be selected.

28
4K /UHD HDR Emulation LCD Monitor

05 MENU OPERATIONS
[5] Waveform & Focus

●● Waveform Trans. (Not Supported)


- Controls the transparency level of the
Waveform/Vectorscope.
- Available values are OPAQUE and TRANS.
* If the option is set to OPAQUE, the main
OSD will overlap with the waveform/vector.
However, it will automatically display it as
transparent and goes back to opaque if the
main OSD disappears.

●● Waveform Color
- Used to select a color of Waveform/
Vectorscope
- Available modes are [Green] and [White].

●● Waveform Display ●● Line Waveform


- This function sets the Waveform and - This item is utilized to display the entire data
Vectorscope. or one line data on the Waveform.
- Activates in the order : [Off], [Waveform],
[Vectorscope]. ●● Line Select Position (*Will be Supported)
* [Waveform] Displays the shape and form of - Used to select specific Horizontal Line for
luminance level of a signal. Waveform/Vectorscope.
* [Vectorscope] : Displays the color components - It is available when Line Waveform is
‘B-Y’ and ‘R-Y’of the input signals onto the activated.
X-Y axis. Two different types of Vetorscopes
are displayed according to SD, HD or UHD/4K
input signals. 100% and 75% scales are
indicated on the Vetorscope

●● Waveform Intensity
- Controls the brightness of the Waveform/
Vectorscope display.
- Available values are between [1] ~ [63].
The higher the number the brighter the
waveform will be.

29
4K /UHD HDR Emulation LCD Monitor

05 MENU OPERATIONS
[5] Waveform & Focus
●● [(Color Patt.) On] mode
- Pixels with Y’ levels which are designated by
the user are displayed in following colors -
yellow, pink, cyan.
- Factory Default Y’ (Border line between pink
and yellow) level is [0]%.
- The upper 2.5% and lower 2.5% zone from
the Y’ level set in [Luma(Y’) Zone Adjust]
menu is displayed in Pink. The upper 10%
zone from the
Pink zone is displayed in Yellow, and the
lower 10% zone from the Pink zone is
displayed in Cyan. So, 25% zone is displayed
in colors and the other 75% zone is displayed
●● Luma(Y’) Zone Check mono and white.
- Analyzes the Luma(Y’) level of the input image
and displays the selected zone on the screen.
- Available modes are [(Color Patt.) On] and
[(Zebra Patt.) On].
- After each pixel’s Y’ level is analyzed, it is
displayed as a certain color or zebra pattern
according to the Index on the right side of the
screen. <Luma Zone Check OFF> <Luma Zone Check ON_Color
Pattern Type>
- When a pixel’s Y’ level is under 0%(16), the
pixel is displayed as green color or green
diagonal lines, and over 100%(235) as red
●● [(Zebra Patt.) On] mode
color or red diagonal lines.
- Pixels with Y’ levels which are designated by
- When the Y’ level of a pixel is between
the user are displayed as black diagonal
0~100%, the pixel is displayed as Gray level,
except for selected Luma Zone. stripes.
- In the [(Color Patt.) On] mode, the zone the - Factory Default Y’ level is [0]%.
user adjusted is displayed as Yellow - The upper 5% and lower 5% zone from the
(10% lower zone), Pink (±2.5%), Y’ level set in [Luma(Y’) Zone Adjust] menu is
Cyan (10% upper zone). displayed as black zebra pattern. So, totally
- In the [(Zebra Patt.) On] mode, ±5% of the 10% zone is displayed as black diagonal
selected Y’ Level will be displayed as diagonal stripes.
lines.
• This function is convenient to set the exposure
or the lighting so that the skin tone or the
specific color tone is correctly shot.

●● Luma(Y’) Zone Adjust


- Used to set the Y’ level to be colored Yellow,
<Luma Zone Check OFF> <Luma Zone Check ON_Zebra
Pink and Cyan in [Color Pattern] mode, or to Pattern Type>
set Y’ level zone to be displayed with
diagonal lines in [Zebra Pattern] mode
simply by scrolling with the Knob.
- Available values are [0] ~ [100%].

30
4K /UHD HDR Emulation LCD Monitor

05 MENU OPERATIONS
[5] Waveform & Focus
●● Focus Assist Level
- Used to set the edge difference value
between the edges in an image.
- Available values are from [0] to [100]. Larger
value means more sophisticated detail
detection.
- Designated color is displayed when the
difference of the edges exceeds the
previously set value.
- This feature is available only when the Focus
Assist mode is activated.

●● Range Error
- Used to set whether or not to activate
●● Focus Assist [Y Max] and [Y Min] functions.
- Focus Assist function assigns a color on the - The values of [Y Max] and [Y Min] are
pixels of the shape or boundary of the image, indicated in Waveform.
which helps the user easily see which part of
the image is in focus or out of focus. • Y Max
- With this function, the user can easily - Used to set the maximum luma(Y') level.
differentiate the focused area from the out- - Available range is [1] to [126].
focused area especially when shooting with
a shallow depth of field. • Y Min
- Available types are [Color On] and [Mono On]. - Used to set the minimum luma(Y') level.
* [Color On]: Background image is original color - Available range is [1] to [126].
type.
* [Mono On]: Background image is mono type.

Focus Assist - [Color On] Focus Assist - [Mono On]


Focus Assist Color - [Green] Focus Assist Color - [Red]

●● Focus Assist Color


- Used to select a color for Focus Assist among
[Red], [Green], [Blue], [White].
- This feature is available only when the Focus
Assist mode is activated.

31
4K /UHD HDR Emulation LCD Monitor

05 MENU OPERATIONS
[6] Audio
●● Level Meter Size
- Used to control the size of the Audio Level
Meter
- Available modes are [Small], [Small Trans.],
[Normal], [Normal Trans.], [Large],
[Large Trans.].
- In Small, Normal and Large modes, the level
meter appears opaque.
- In [Small Trans.], [Normal Trans.],
[Large Trans.] modes, the level meter appears
semitransparent.

●● Volume
- Used to control the output volume of the
●● Level Meter Select [AUDIO OUT] terminal on the back of the
- Used to control the Embedded Audio Level monitor.
- Control range is from 0 to 30.
Meters.
- Available modes are [Off], [G1+G2], [G2+G3],
●● Em. Audio Left
[G3+G4], [G1+G3], [G1+G4], [G2+G4] and [16CH]. - Used to set embedded audio channel for left
audio out of [AUDIO OUT] terminal on the
●● Level Meter Display back of the monitor.
- Used to set the display method for Audio - Available modes are [CH1], [CH2], ..., [CH16],
Level Meter. [Ext. Audio], [Off].
- Available modes are Group and Pair.
●● Em. Audio Right
- Used to set embedded audio channel for
●● Level Meter Reference right audio out of [AUDIO OUT] terminal on
- Display the default Audio Level Meter value. the back of the monitor.
- Available options are -18dB and -20dB. - Available modes are [CH1], [CH2], ..., [CH16],
- Audio Level Meter within selected value turns [Ext. Audio], [Off].
to green and exceeded audio level is
displayed in yellow. Audio level exceeding -
4dB is displayed in red.

●● Peak Decay Time


- Sets the reduction time for the max value
indication of audio signals.
- Control range is from [0] to [30]. Larger number
means a longer display time for max. value.

32
4K /UHD HDR Emulation LCD Monitor

05 MENU OPERATIONS
[7] Display & Set
●● Key Lock
- Used to lock all buttons except Power, Input
select and Menu buttons.

●● Key LED
- Used to control the Key Lamp on the front
of the monitor.
- If the button with LED is pressed with the
KEY LED Off, LED comes on but turns off after
5 seconds later.

●● User config set


- Used to save and apply in three kinds of user
configurations.
- Available modes are [USER1], [USER2] and
[USER3].

●● Internal Pattern
- Generates White Pattern internally.
- Selectable range is from [0%] to [100%] with
5% increment.

●● System Default
- Used to initialize OSD values to factory
default.

●● S/W Upgrade
- Used to upgrade the firmware using the USB
memory (Thumb drive).
- Select the S/W Upgrade Start menu to start
the USB memory search.
- When the USB memory is detected, the S/W
Upgrade Start menu becomes activated.

●● S/W Upgrade Start


- Select the S/W Upgrade Start menu to start
the firmware upgrade.
- Do not turn off the monitor while the upgrade
is conducting.

●● Time Code
- Used to set the Time Code.
- Available modes are [OFF], [VITC] and [LTC].

33
4K /UHD HDR Emulation LCD Monitor

05 MENU OPERATIONS
[7] Display & Set

LUM-181H LUM-181H

Closed Caption Off [F1] Key Mapping Marker


Decode Channel(608) CC1 [F2] Key Mapping Waveform
Caption Service(708) Service 1 [F3] Key Mapping Video Range
OSD position Center [F4] Key Mapping Scan
Transfer Matrix Default [F5] Key Mapping Aspect

Gamut Control Surface


Serial Number :
Board Version 2003 0077 03 2.04 9

●● Closed Caption ●● [F1] Key Mapping


- This item controls the Closed Caption. - User can select the function for the F1 button.
- Available modes are [OFF], [708], [608(LINE21)]
and [608(ANC)]. ●● [F2] Key Mapping
- User can select the function for the F2 button.
●● Decode Channel(608)
- Sets the Channel of Closed Caption 608 ●● [F3] Key Mapping
- Available modes are [CC1] ~ [CC4]. - User can select the function for the F3 button.

●● Caption Service(708) ●● [F4] Key Mapping


- Sets the service of Closed Caption 708. - User can select the function for the F4 button.
- Available modes are [Service 1] ~ [Service 6].
●● [F5] Key Mapping
●● OSD Position - User can select the function for the F5 button.
- This item controls the OSD position. The following functions can be assigned.
- Available values are [Center], [Top-Right], [Blue Only], [H/V Delay], [White Point],
[Bottom-Right], [Bottom-Left] and [Top-Left]. [Audio Level Meter], [Time Code],
[Luma(Y') Zone], [Focus Assist], [Marker],
●● Transfer Matrix [DR Mode], [Standard], [Disp Luminance],
- Used to select the Signal Transmission Matrix. [EOTF], [Video Range], [Waveform],
- Available options are [Default], [Rec709] and [Scan], [Aspect], [Native Mode],
[Rec2020]. [Gumar Warning], [Shadow Mode], [4K Align].
* Default : If the Color Gamut is selected as
BT.2020, it is applied as Rec2020 Matrix. ●● Serial Number
If the Color Gamut is selected other than - Used to display serial number of the monitor.
BT.2020, it is applied as Rec709 Matrix.
* Rec709 and Rec2020 are applied to the ●● Board Version
corresponding Matrix regardless of the color - Displays the current Program Version of the
gamut. monitor.
2003 0077 03 2.04 9
●● Gamut Control (*Will be supported)
- Used to efficiently map the difference
between the Panel and the Standard color KEYPAD VERSION
gamut. CPU VERSION
*Surface : Used to map the colors outside FPGA VERSION
of the panel’s color gamut onto the internal
GPU VERSION
color.

34
4K /UHD HDR Emulation LCD Monitor

05 MENU OPERATIONS
[8] Inform. (INFO. KEY)
●● Bit Depth
- Displays the Bit Depth information of the
Payload ID Byte 4.

●● Link Assignment
- Displays the Channel Assignment information
of the Payload ID Byte 4.

●● Input Channel
- Indicates the channel of the input signal.
- In the 2SI, QUAD MODE, use the KNOB button
to change the input signal and the
information of the signal will be displayed.
- In the SINGLE MODE, the signal information of
the channel will be displayed.

●● Input Config
- Displays the current input signal.

●● SDI Payload ID
- Displays the values of the Byte 1,2,3,4.

●● Video Standard
- Displays the standard of the Payload ID
Byte 1.

●● Sampling
- Displays the Sampling Structure information
of the Payload ID Byte 3.

●● Picture Rate
- Displays the Picture Rate of the Payload ID
Byte 2.

●● Scanning Method
- Displays the Interlace/Progressive of the
Payload ID Byte 2.

35
4K /UHD HDR Emulation LCD Monitor

06 VIDEO SUPPORT RESOLUTION


Input Signal Interfaces Signal Format (HD-SDI / 3G SDI)

3840x2160
HD-SDI (23.98/24/25/29.97/30p/Psf) YCbCr 4:2:2 10bit
Quad link (4K) 4096x2160
(23.98/24/25/29.97/30p/Psf)

Input Signal Interfaces Signal Format (HD-SDI / 3G SDI)

3840x2160(50/59.94/60p) YCbCr 4:2:2 10bit


3840x2160 YCbCr 4:4:4 10/12bit
(23.98/24/25/29.97/30/p/Psf) RGB 4:4:4 10/12bit
3G-SDI
Quad link(4K) 4096x2160
YCbCr 4:2:2 10bit
(47.95/48/50/59.94/60p)
4096x2160 YCbCr 4:4:4 10/12bit
(23.98/24/25/29.97/30p/Psf) RGB 4:4:4 10/12bit
3840x2160
3G-SDI YCbCr 4:2:2 10bit
(23.98/24/25/29.97/30/p)
2-Sample Interleave
Dual link(4K) 4096x2160
YCbCr 4:2:2 10bit
(23.98/24/25/29.97/30p)

3840x2160(50/59.94/60p) YCbCr 4:2:2 10bit

3G-SDI 3840x2160 YCbCr 4:4:4 10/12bit


2-Sample Interleave (23.98/24/25/29.97/30/p) RGB 4:4:4 10/12bit
/Square 4096x2160 YCbCr 4:4:4 10/12bit
Quad link(4k) (23.98/24/25/29.97/30p) RGB 4:4:4 10/12bit
4096x2160
YCbCr 4:2:2 10bit
(47.95/48/50/59.94/60p)

3840x2160(23.98/24/25/29.97/30/p)
6G-SDI
YCbCr 4:2:2 10bit
Single link(4K)
4096x2160(23.98/24/25/29.97/30p)

3840x2160(50/59.94/60p)
12G-SDI
YCbCr 4:2:2 10bit
Single link(4K) 4096x2160
(47.95/48/50/59.94/60p)

36
4K /UHD HDR Emulation LCD Monitor

06 VIDEO SUPPORT RESOLUTION


Input Signal Interfaces Signal Format (HDMI)

720x480(60i) RGB 4:4:4 8/10/12bit


720x576(50i) YCbCr 4:4:4 8/10/12bit

720x480(60p)
720x576(50p) RGB 4:4:4 8/10/12bit
1280x720(60p) YCbCr 4:4:4 8/10/12bit
1920x1080(50/59.94/60i) YCbCr 4:2:2 12bit
1920x1080(50/59.94/60p)

HDMI
Single link(4K) 800x600@60Hz
1024x768@60Hz
VESA
1280x1024@60Hz
1600x1200@60Hz

3840x2160 (23.98/24/25/29.97/30) RGB 4:4:4 8bit


4096x2160 (23.98/24/25/29.97/30) YCbCr 4:4:4 8bit

3840x2160 (50/60p) RGB 4:4:4 8bit


4096x2160 (50/60p) YCbCr 4:4:4 8bit

37
4K /UHD HDR Emulation LCD Monitor

07 PRODUCT SPECIFICATIONS

38
4K /UHD HDR Emulation LCD Monitor

07 OPTIONAL ACCESSORIES

39
4K /UHD HDR Emulation LCD Monitor

07 PRODUCT SPECIFICATIONS

40
4K /UHD HDR Emulation LCD Monitor

07 OPTIONAL ACCESSORIES
Specifications LUM-242G
Size 23.8”
Resolution 3840 X 2160 (16:9)
Pixel Pitch 0.137(H) X 0.137(V) mm
Color Depth 1.07B
LCD
Viewing Angle 178°(H) / 178°(V)
Luminance of white 540 cd/ m2 (Center)
Contrast Ratio 1200 : 1
Display Area 526(H) X 296(V) mm
1 X HDMI HDMI Input
Input Connector
4 X BNC 12G-SDI A/B, 3G-SDI C/D Channel Input
Output 4 X BNC 12G-SDI A/B, 3G-SDI C/D Channel (Active Through Out)
12G-SDI 12Gb/s
6G-SDI 6Gb/s
Input Signal 3G-SDI 2.970Gb/s
HD-SDI 1.485Gbps
HDMI 480p/720p/1080p/2160p
1080p(60/59.94/50/30/29.97/25/24/23.98/30sF/29.97sF/25sF/24sF/23.98sF)
SMPTE-425M-A/B
1080i(60/59.94/50)
1080i (60/59.94/50)
SMPTE-274M
1080p (30/29.97/25/24/24sF/23.98/23.98sF)
SMPTE-296M 720p (60/59.94/50)
SDI Input Signal SMPTE-260M 1035i (60/59.94)
Formats SMPTE-125M 480i (59.94)
ITU-R BT.656 576i (50)
SMPTE ST 2036-1:2009 3840×2160(23.98/24/25/29.97/30/50/59.94/60p)
SMPTE ST 2048-2:2011 2048x1080(23,98/24/25/29.97/30p/psf, 47.95/48/50/59.94/60p)
SMPTE ST 2081 3840x2160 (30/25/24p)
SMPTE ST 2082 3840x2160 (60/50/30/25/24p)
Audio In Embedded Audio / Analog Stereo (Phone Jack)
Audio Out Internal Speaker (Stereo) / Analog Stereo (Phone Jack)
Power DC 24V / AC100~240V(50~60Hz)
Power Consumption (Approx.) 85Watts
Operating Temperature 0℃ to 35℃ (32℉ to 95℉)
Storage Temperature -20℃ to 60℃ (-4℉ to 140℉)
Main Body Dimensions (mm/inch) 552.48 x 360.4 x 95.9 (21.75 x 14.18 x 3.77)
Main Body Dimensions with stand (mm/inch) 586.13 x 388.2 x 150 (23.07 x 15.28 x 5.90)
Box Dimensions (mm/inch) 555 X 450 X 280 (21.85 X 17.72 X 11.02)
Weight 10.5kg / 23.14lbs
Basic Accessories AC Power Cord, Stand
Optional Accessories Acrylic Filter, ND Filter, V-mount, G-mount, Carrying Case, Rack Mountable Kit

41
4K /UHD HDR Emulation LCD Monitor

07 PRODUCT SPECIFICATIONS

42
4K /UHD HDR Emulation LCD Monitor

07 OPTIONAL ACCESSORIES

43

You might also like