Scribd Logo
Upload

Welcome to Scribd!

  • 264 views

    Experiment: 2 1.0 TOPIC: R R C F

    Uploaded by

    Lian Ai Chen
    The document describes an experiment to build and test a phase shift oscillator circuit. The objectives are to construct the circuit, observe the output waveform and measure frequency, determine the frequency range by varying resistor and capacitor values, and understand how phase shift oscillators work. It provides the theory of operation, required equipment, procedures to build and test the circuit, expected results, and questions for analysis and discussion.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as DOC, PDF, TXT or read online from Scribd

    Experiment: 2 1.0 TOPIC: R R C F

    Uploaded by

    Lian Ai Chen
    264 views4 pages
    The document describes an experiment to build and test a phase shift oscillator circuit. The objectives are to construct the circuit, observe the output waveform and measure frequency, determine the frequency range by varying resistor and capacitor values, and understand how phase shift oscillators work. It provides the theory of operation, required equipment, procedures to build and test the circuit, expected results, and questions for analysis and discussion.

    Original Title

    Experiment 2

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    DOC, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document describes an experiment to build and test a phase shift oscillator circuit. The objectives are to construct the circuit, observe the output waveform and measure frequency, determine the frequency range by varying resistor and capacitor values, and understand how phase shift oscillators work. It provides the theory of operation, required equipment, procedures to build and test the circuit, expected results, and questions for analysis and discussion.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as DOC, PDF, TXT or read online from Scribd
    Download as doc, pdf, or txt
    264 views4 pages

    Experiment: 2 1.0 TOPIC: R R C F

    Uploaded by

    Lian Ai Chen
    The document describes an experiment to build and test a phase shift oscillator circuit. The objectives are to construct the circuit, observe the output waveform and measure frequency, determine the frequency range by varying resistor and capacitor values, and understand how phase shift oscillators work. It provides the theory of operation, required equipment, procedures to build and test the circuit, expected results, and questions for analysis and discussion.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as DOC, PDF, TXT or read online from Scribd
    Download as doc, pdf, or txt
    of 4

    EXPERIMENT: 2 1.0 TOPIC Phase Shift Oscillator 2.

    0 OBJECTIVES: In the end of the experiment, the student should be able to: 1. Build the phase shift oscillator. 2. Observe the output waveform and measure the output frequency. 3. Determine the range of frequency variation of resistor and capacitor ( RC) phaseshift oscillator. 4. Understand the working principle of the Phase-Shift oscillator. 3.0 THEORY: A phase-shift oscillator is a simple electronic oscillator and is catagorized in the RC filter as shown in Figure 2.1. It contains an inverting amplifier, and a feedback filter which 'shifts' the phase of the amplifier output by 180 degrees at a specific oscillation frequency. The basic requirement for an oscillator is positive feedback. Frequency of oscillation is given below:
    f = 1 2C 61 + 4 R1 R L
    2

    EQUA 3.1

    Figure 3.1

    4.0

    EQUIPMENT: 4.1 Variable resistor (5K) 4.2 Transistor 2N3904 4.3 Capacitor 47nF and 2.2Nf 4.4 Resistor 4.7K, 1.2K and 56K 4.5 Oscilloscope 4.6 Multimeter 4.7 Frequency counter. 4.8 Jumper. PROCEDURE:

    5.0

    Figure 2.2: Phase Shift Oscillator Circuit (RC Oscillator) 1. Connect the circuit as shown in Figure 2.2. 2. Connect the circuits by using a 5k variable resistor .Set the variable resistor to the 1k for maximum value. 3. Make sure that your circuit connections are correct and get approval from your lecturer. 4. Connect the circuit with DC power supply and turn on the power switch. 5. Close the switch. With an oscilloscope observe and measure the waveform and its peak to peak voltage at TP1, TP2 and TP3. Record the data in the Table 2.1. 6. Using a digital frequency counter to determine the oscillator frequency by set the variable resistor to the maximum. Record the data in Table 2.1.

    6.0

    RESULT: Test point TP1 Waveform Vp-p Frequency

    TP2

    TP3

    Table 2.1: RC oscillator Frequency Range 7.0 QUESTIONS: 7.1 Using your own word, explain the operation of the phase shift oscillator. 7.2 Why is there a difference in amplitude between the feedback voltage at TP1, 2 and 3. DISCUSSION CONCLUSION

    8.0 9.0

    10.0

    ASSESSMENT CRITERIA: 10.1 LABORATORY Cooperation : ( Discipline : ( Results : ( TOTAL : 10.2 REPORT Report : Result : Questions : Analysis/Calculation Discussion : Conclusion : TOTAL :

    / 5 marks) / 10 marks) / 15 marks)

    ( ( ( ( (

    / 10 marks) / 10 marks) / 15 marks) / 20 marks) / 15 marks)

    You might also like