Flow Meter Data Sheet

Download as pdf or txt
Download as pdf or txt
You are on page 1of 2

3500/6000 PSI High Temperature

Flow Meters For Petroleum Fluids


• Direct reading SPECIFICATIONS:
MATERIALS:
• Install in any position 2024 - T351 Anodized aluminum body, piston and cone
• 360° rotatable guard/scale C360 Brass body, piston and cone
• Easier-to-read linear scale T303 Stainless body, 2024 - T351 Anodized aluminum piston and cone
• No flow straighteners or COMMON PARTS: Retaining Ring: SAE 1070/1090 Carbon Steel
special piping required Spider Plate: T316 SS Retaining Spring: SAE 1070/1090 Carbon Steel
Spring: T302 SS Indicator: Nickel-plated Carbon Steel
• Relatively insensitive to Fasteners: T303 SS Internal Magnet: Teflon® Coated Alnico 8
shock and vibration Seals: Viton® Bumper: 2011 - T3 Anodized Aluminum
• Good viscosity stability Scale Support: T316 SS Guard: Cylindrical Pyrex® Glass
• Temperature up to 500 °F Scale: Polymide End Caps: 2011 - T3 Anodized Aluminum
• Accuracy ±2% full scale THREADS: SAE J1926/1, NPTF ANSI B2.2, BSPP ISO1179, Code 62: SAEJ518
TEMPERATURE RANGE: -20 to +400 °F (-29 to +205 °C ) Continuous
• Repeatability ±1%
+400 to +500 °F (+205 to +260 °C ) Intermittent
• Special scales available For detailed “Pressure vs. Temperature” correlation information, see page 14.
• Calibrated for .876 S.G. PRESSURE RATING:
Aluminum / Brass Operating: 3,500 psi/241 bar max. with a 3:1 safety factor.
For High Cycle Applications: See page 7
Stainless Steel Operating: 6,000 psi/414 bar max. (5,000 psi/345 bar max.
for ¾" to 1½" series) with a 3:1 safety factor.
For High Cycle Applications: See page 7
PRESSURE DROP: See Ordering Information Table, page 14.
For detailed differential pressure charts, see page 55.
ACCURACY: ±2% of full scale REPEATABILITY: ±1%
REVERSE FLOW BY-PASS OPTION: Features a two-piece cone that responds
to flow in the primary flow direction in the same manner as the standard design.
Flow in the reverse direction causes the lower cone shuttle to shift, moving it below
the sharp-edged piston orifice, which allows the fluid to flow freely in the reverse direction.

Normal Flow Direction Reverse Flow By-Pass

DIMENSIONS:
A B C D
NOMINAL LENGTH WIDTH FLATS
PORT SIZE in (mm) in (mm) in (mm)
¼ (SAE 6) 6.60 (168) 2.01 (53) 1.25 (32)
½ (SAE 10) 6.60 (168) 2.01 (53) 1.25 (32)
¾ (SAE 12) 7.20 (183) 2.48 (63) 1.50 (38)
1 (SAE 16) 7.20 (183) 2.48 (63) 1.75 (44)
1¼ (SAE 20) 12.20 (310) 4.20 (105) 2.75 (70)
1½ (SAE 24) 12.20 (310) 4.20 (105) 2.75 (70)
NOTE: Dimensions for 1½" Code 62 can be found on page 78.
Weights for all sizes can be found on page 79.
Pyrex is a registered trademark of Corning, Inc.
Teflon is a registered trademark of E.I. DuPont de Nemours & Co.
Viton is a registered trademark of DuPont Dow Elastomers

15
3500/6000 PSI High Temperature
Flow Meters For Petroleum Fluids
ORDERING INFORMATION:
NOMINAL FLOW RANGE PRESSURE DROP MODEL NUMBER (see example below) MATERIAL OPTIONS
PORT 50% 100% REVERSE ALUMINUM BRASS REVERSE
GPM LPM FLOW FLOW 100% FLOW SAE NPTF BSPP STAINLESS
SIZEc PSI (BAR) PSI (BAR) PSI (BAR) 3500 PSI 3500 PSI FLOW
¼" 0.1 - 1.0 0.5 - 3.75 4.0 (.28) 9.0 (.62) H200 - 010 - HT H201 - 010 - HT H202 -010 - HT 6000 PSI Not
* * *
SAE 6 0.2 - 2.0 1.0 - 7.5 6.0 (.41) 13 (.90) H200 - 020 - HT H201 - 020 - HT H202 -020 - HT
* * * A B S Available
0.1 - 1.0 0.5 - 3.75 2.0 (.14) 2.75 (.19) 5.2 (.36) H600 - 001 - HT H601 - 001 - HT H602 -001 - HT 6000 PSI
* * *
0.2 - 2.0 1.0 - 7.5 2.0 (.14) 3.0 (.21) 9.6 (.66) H600 - 002 - HT H601 - 002 - HT H602 -002 - HT
½" * * *
SAE 10
0.5 - 5.0 2 - 19
1 - 10 5 - 38
3.0 (.21) 6.0 (.41) 4.8 (.33) H600 - 005 - HT H601 - 005 - HT H602 -005 - HT
* * *
4.0 (.28) 9.5 (.66) 23.0 (1.6) H600 - 010 - HT H601 - 010 - HT H602 -010 - HT
A B S HR
1 - 15 4 - 56
* * *
6.5 (.45) 18.5 (1.3) 55.2 (3.8) H600 - 015 - HT H601 - 015 - HT H602 -015 - HT
* * *
0.2 - 2.0 1 - 7.5 1.0 (.07) 2.0 (.14) 2.9 (.20) H700 - 002 - HT H701 - 002 - HT H702 -002 - HT 5000 PSI
0.5 - 5.0 2 - 19
* * *
2.5 (.17) 3.5(.24) 5.3 (.37) H700 - 005 - HT H701 - 005 - HT H702 -005 - HT
¾" * * *
SAE 12
1 - 10
2 - 20
5 - 38 3.5 (.24) 9.0 (.62) 8.8 (.61) H700 - 010 - HT H701 - 010 - HT H702 -010 - HT
* * *
10 - 76 4.0 (.28) 9.0 (.62) 18.0 (1.24) H700 - 020 - HT H701 - 020 - HT H702 -020 - HT
A B S HR
* * *
3 - 30 10 - 115 7.0 (.48) 16.5 (1.1) 45.1 (3.11) H700 - 030 - HT H701 - 030 - HT H702 -030 - HT
* * *
0.2 - 2.0 1 - 7.5 1.0 (.07) 2.0 (.14) 2.9 (.20) H760 - 002 - HT H761 - 002 - HT H762 - 002 - HT 5000 PSI
0.5 - 5.0 2 - 19
* * *
2.5 (.17) 3.5(.24) 5.3 (.37) H760 - 005 - HT H761 - 005 - HT H762 - 005 - HT
1 - 10 5 - 38
* * *
3.5 (.24) 9.0 (.62) 8.8 (.61) H760 - 010 - HT H761 - 010 - HT H762 - 010 - HT
1" * * *
SAE 16
2 - 20 10 - 76 4.0 (.28) 9.0 (.62) 18.0 (1.24) H760 - 020 - HT H761 - 020 - HT H762 - 020 - HT
* * *
3 - 30 10 - 115 7.0 (.48) 16.5 (1.1) 45.1 (3.11) H760 - 030 - HT H761 - 030 - HT H762 - 030 - HT
A B S HR
4 - 40 15 - 150 9.0 (.62) 24.0 (1.7) 87.5 (6.04)
* * *
H760 - 040 - HT H761 - 040 - HT H762 - 040 - HT
* * *
5 - 50 20 - 190 12.5 (.86) 34.0 (2.3) 150 (10.4) H760 - 050 - HT H761 - 050 - HT H762 - 050 - HT
* * *
3 - 30 10 - 110 3.0 (.21) 4.0 (.28) 4.8 (.33) H800 - 030 - HT H801 - 030 - HT H802 - 030 - HT 5000 PSI
5 - 50 20 - 190 3.5 (.24) 7.0 (.48) 12.5 (.86) H800 * - 050 - HT H801 * - 050 - HT H802 * - 050 - HT
10 - 75 40 - 280 5.0 (.35) 10.5 (.72) 31.9 (2.2) H800 * - 075 - HT H801 * - 075 - HT H802 * - 075 - HT
1¼"
SAE 20
10 - 100 50 - 380 6.5 (.45) 15 (1.0) 39.0 (2.7) H800 * - 100 - HT H801 * - 100 - HT H802 * - 100 - HT
A B S HR
10 - 150 50 - 560 10.5 (.72) 27.5 (1.9) 110 (7.6) H800 * - 150 - HT H801 * - 150 - HT H802 * - 150 - HT
* * * 5000 PSI
3 - 30 10 - 110 3.0 (.21) 4.0 (.28) 4.8 (.33) H860 - 030 - HT H861 - 030 - HT H862 - 030 - HT
* * *
5 - 50 20 - 190 3.5 (.24) 7.0 (.48) 12.5 (.86) H860 - 050 - HT H861 - 050 - HT H862 - 050 - HT
1½" * * *
SAE 24
10 - 75 40 - 280 5.0 (.35) 10.5 (.72) 31.9 (2.2) H860 - 075 - HT H861 - 075 - HT H862 - 075 - HT
* * *
10 - 100 50 - 380 6.5 (.45) 15 (1.0) 39.0 (2.7) H860 - 100 - HT H861 - 100 - HT H862 - 100 - HT
A B S HR
* * *
10 - 150 50 - 560 10.5 (.72 27.5 (1.9) 110 (7.6) H860 - 150 - HT H861 - 150 - HT H862 - 150 - HT
* * *
3 - 30 10 - 110 3.0 (.21) 4.0 (.28) 4.8 (.33) H808 - 030 - HT 4000 PSI
5 - 50 20 - 190 3.5 (.24) 7.0 (.48) 12.5 (.86) H808 * - 050 - HT
10 - 75 40 - 280 5.0 (.35) 10.5 (.72) 31.9 (2.2) H808 * - 075 - HT
1½"
Code 62
10 - 100 50 - 380 6.5 (.45) 15 (1.0) 39.0 (2.7) H808 * - 100 - HT
A B S HR
10 - 150 50 - 560 10.5 (.72) 27.5 (1.9) 110 (7.6) H808 * - 150 - HT
*
cFractional sizes apply to NPTF and BSPP.
(example) H 701 A - 030 - HR

NOTE: HT suffix represents standard high temperature configuration.


For reverse flow high temperature, replace HT with HR suffix.
NOTE: HR option is not available with brass flow meters.

16

You might also like