36-1

GROUP 36

PARKING BRAKES
CONTENTS

GENERAL DESCRIPTION. . . . . . . . . 36-2 PARKING BRAKE LEVER . . . . . . . . . 36-16

REMOVAL AND INSTALLATION . . . . . . . . 36-16
PARKING BRAKE DIAGNOSIS . . . . 36-2
INTRODUCTION. . . . . . . . . . . . . . . . . . . . . 36-2 PARKING BRAKE CABLE. . . . . . . . . 36-17
TROUBLESHOOTING STRATEGY . . . . . . 36-2 REMOVAL AND INSTALLATION . . . . . . . . 36-17
SYMPTOM CHART. . . . . . . . . . . . . . . . . . . 36-3
SYMPTOM PROCEDURES . . . . . . . . . . . . 36-3 PARKING BRAKE LINING
AND DRUM . . . . . . . . . . . . . . . . . . . . . 36-18
ON-VEHICLE SERVICE. . . . . . . . . . . 36-13 REMOVAL AND INSTALLATION . . . . . . . . 36-18
PARKING BRAKE LEVER STROKE INSPECTION. . . . . . . . . . . . . . . . . . . . . . . . 36-21
CHECK AND ADJUSTMENT . . . . . . . . . . . 36-13
PARKING BRAKE SWITCH CHECK . . . . . 36-14 SPECIFICATIONS . . . . . . . . . . . . . . . 36-22
PARKING BRAKE LINING SEATING FASTENER TIGHTENING
PROCEDURE . . . . . . . . . . . . . . . . . . . . . . . 36-15 SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . 36-22
SERVICE SPECIFICATIONS . . . . . . . . . . . 36-22
LUBRICANT . . . . . . . . . . . . . . . . . . . . . . . . 36-22
36-2 PARKING BRAKES
GENERAL DESCRIPTION

GENERAL DESCRIPTION
M1361000100559
The parking brakes are a mechanical rear wheel
brake design and controlled by a lever.

CONSTRUCTION DIAGRAM

PARKING BRAKE LEVER

FRONT PARKING AC206222

BRAKE CABLE

REAR PARKING
BRAKE CABLE

AC405949AB

PARKING BRAKE DIAGNOSIS

INTRODUCTION
M1361003700282
If the parking brake is faulty, parking brake effort will
become insufficient. The cause may be a malfunc-
tion of parking brake parts or the parking brake pedal
being out of adjustment.
TROUBLESHOOTING STRATEGY
M1361003800290
Use these steps to plan your diagnostic strategy. If 2. Verify that the condition described by the
you follow them carefully, you will be sure that you customer exists.
have exhausted most of the possible ways to find a 3. Find the malfunction by following the Symptom
parking brakes fault. Chart.
1. Gather Information from the customer. 4. Verify malfunction is eliminated.

TSB Revision
 PARKING BRAKES
PARKING BRAKE DIAGNOSIS
36-3
SYMPTOM CHART
M1361004100368

SYMPTOM INSPECTION REFERENCE PAGE

PROCEDURE
Brake drag − Refer to GROUP 35A, Basic Brake
System Diagnosis −Symptom
Chart P.35A-7.
Insufficient parking brake function 1 P.36-3
When the parking brake lever is pulled, the brake 2 P.36-4
warning light does not illuminate.
When the parking brake lever is released, the brake 3 P.36-8
warning light does not turn off.

SYMPTOM PROCEDURES

INSPECTION PROCEDURE 1: Insufficient Parking Brake Function

DIAGNOSIS STEP 3. Check the brake lining and brake drum

for wear.
STEP 1. Check the excessive parking brake lever Refer to P.36-21.
stroke. Q: Is the brake lining thickness or brake drum inside
Refer to P.36-13. diameter outside of specification?
Q: Is the parking brake lever stroke adjusted YES : Replace the rear brake shoe assembly or
properly? rear brake disc (Refer to P.36-18). Then go
YES : Go to Step 2. to Step 5.
NO : Adjust the parking brake lever stroke or NO : Go to Step 4.
check the parking brake cable routing. Then
go to Step 5. STEP 4. Check for oil, water, etc., on the lining
contact surfaces.
STEP 2. Check the parking brake cable for Q: Is oil, water, etc., on the lining contact surface?
sticking. YES : Replace the part and determine and repair
Q: Is the parking brake cable stuck? source/cause of foreign material. Then go to
YES : Replace the cable. Then go to Step 5. Step 5.
NO : Go to Step 3. NO : Carry out the parking brake lining seating
procedure (Refer to P.36-15) and then go to
Step 5.

STEP 5. Retest the system.

Q: Is the malfunction eliminated?
YES : The procedure is complete.
NO : Recheck from Step 1.

TSB Revision
36-4 PARKING BRAKES
PARKING BRAKE DIAGNOSIS

INSPECTION PROCEDURE 2: When the Parking Brake Lever is Pulled, the Brake Warning Light does
not Illuminate.

Brake Warning Light Circuit

COMBINATION
METER

BRAKE FLUID
LEVEL SWITCH

PARKING
BRAKE
SWITCH

CONNECTORS: C-04, C-24 CONNECTOR: C-16

C-04

C-24

C-16 (B)
AC406442CN AC406444 DC

TSB Revision
 PARKING BRAKES
PARKING BRAKE DIAGNOSIS
36-5
TECHNICAL DESCRIPTION (COMMENT)
.

TROUBLESHOOTING HINTS (THE MOST

• The parking brake switch turns on and off by
operating the parking brake lever, and the brake
LIKELY CAUSES FOR THIS CASE:)
warning light illuminates and goes out, indicating • Damaged wiring harness or connector
the operating status of parking brake to a driver. • Brake fluid level switch defective
• The brake fluid level switch is installed to the • Parking brake switch defective
master cylinder and the switch turns on when the • Combination meter defective
brake fluid reach the lower level. Therefore, the
brake warning light illuminates to indicate the sta-
tus to the driver.
.

DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: MUT-III USB Cable
• MB991910: MUT-III Main Harness A

STEP 1. Using scan tool MB991958, check combination

meter actuator test.
CAUTION
AC305412 To prevent damage to scan tool MB991958, always turn the
DATA LINK
CONNECTOR ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Turn the parking brake switch and brake fluid level switch to
"OFF" position.
(4) Set scan tool MB991958 to the actuator test mode.
• Item 20: Indicator lamp 1: ON
MB991910
• The brake warning light illuminates..
MB991824 • Item 21: Indicator lamp 1: OFF
• The brake warning light goes out.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the check result normal?
YES : Go to Step 2.
NO : Replace the combination meter (Refer to GROUP
54A, Combination meter assembly P.54A-131).

MB991827
AC404789AB

STEP 2. Check the parking brake switch.

Refer to P.36-14.
Q: Is the parking brake switch normal?
YES : Go to Step 3.
NO : Replace the parking brake switch. then go to Step
Step 7.

TSB Revision
36-6 PARKING BRAKES
PARKING BRAKE DIAGNOSIS

STEP 3. Check parking brake switch connector C-16,

intermediate connector C-24 and combination meter
connector C-04 for loose, corroded or damaged terminals,
or terminals pushed back in the connector.
CONNECTORS: C-04, C-24 Q: Are the connectors and terminals in good condition?
C-04 YES : Go to Step 4.
C-04 HARNESS SIDE NO : Repair or replace the faulty connector. (Refer to
GROUP 00E, Harness Connector Inspection
P.00E-2). Then go to Step 7.
C-24

C-24 AC406442CO

CONNECTOR: C-16

HARNESS SIDE

C-16 (B)
AC406444 DB

STEP 4. Check the harness wire parking brake switch

connector C-16 terminal 1 and combination meter
connector C-04 terminal 9 for damage.
CONNECTOR: C-04 Q: Are the harness wires in good condition?
YES : Go to Step 5.
NO : Repair the damaged harness wire. Then go to Step 7.
HARNESS SIDE

AC406442AB

CONNECTOR: C-16

HARNESS SIDE

C-16 (B)
AC406444 DB

TSB Revision
 PARKING BRAKES
PARKING BRAKE DIAGNOSIS
36-7

STEP 5. Check the parking brake switch ground for

damage.
CONNECTOR: C-16 Q: Is the parking brake switch ground in good condition?
YES : Go to Step 6.
NO : Repair the ground or damaged harness wire. Then go
HARNESS SIDE to Step 7.

C-16 (B)
AC406444 DB

STEP 6. Retest the system.

Q: Does the brake warning light illuminate when the
parking brake lever is pull?
YES : It can be assumed that this malfunction is intermittent.
(Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points −How to
Cope with Intermittent Malfunction P.00-14).
NO : Replace the combination meter (Refer to GROUP
54A, Combination meter assembly P.54A-131).

STEP 7. Retest the system

Q: Does the brake warning light illuminate when the
parking brake lever is pulled?
YES : The procedure is complete.
NO : Return to Step 1.

TSB Revision
36-8 PARKING BRAKES
PARKING BRAKE DIAGNOSIS

INSPECTION PROCEDURE 3: When the Parking Brake Lever is Released, the Brake Warning Light
does not Turn Off.

Brake Warning Light Circuit

COMBINATION
METER

BRAKE FLUID
LEVEL SWITCH

PARKING
BRAKE
SWITCH

CONNECTOR: A-04 CONNECTORS: C-04, C-24

C-04

A-04 (GR)

C-24

AC406432 BB AC406442CN

TSB Revision
 PARKING BRAKES
PARKING BRAKE DIAGNOSIS
36-9
CONNECTOR: C-16

C-16 (B)
AC406444 DC

. .

TECHNICAL DESCRIPTION (COMMENT) TROUBLESHOOTING HINTS (THE MOST

• The parking brake switch turns on and off by LIKELY CAUSES FOR THIS CASE:)
operating the parking brake lever, and the brake • Damaged wiring harness or connector
warning light illuminates and goes out, indicating • Brake fluid level switch defective
the operating status of parking brake to a driver. • Parking brake switch defective
• The brake fluid level switch is installed to the • Combination meter defective
master cylinder and the switch turns on when the
brake fluid reach the lower level. Therefore, the
brake warning light illuminates to indicate the sta-
tus to the driver.
.

DIAGNOSIS
Required Special Tools:
• MB991958: Scan Tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: MUT-III USB Cable
• MB991910: MUT-III Main Harness A

STEP 1. Check the brake fluid level.

Refer to GROUP 35A, On-vehicle Service −Brake Fluid Level
Inspection and Bleeding P.35A-17.
Q: Is the brake fluid level within between the lower level
and upper level?
YES : Go to Step 2.
NO : Check if the brake pad is worn (Refer to GROUP 35A,
On-vehicle service −Disc Brake Pad Check and
Replacement P.35A-19). If not, replenish the brake
fluid (Refer to GROUP 35A, On-vehicle Service −
Brake Fluid Level Inspection and Bleeding P.35A-17).
Then go to Step 9.

TSB Revision
36-10 PARKING BRAKES
PARKING BRAKE DIAGNOSIS

STEP 2. Using scan tool MB991958, check actuator test.

CAUTION
AC305412 To prevent damage to scan tool MB991958, always turn the
DATA LINK
CONNECTOR ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958 to the data link connector.
(2) Turn the ignition switch to the "ON" position.
(3) Turn the parking brake switch and brake fluid level switch to
"OFF" position.
(4) Set scan tool MB991958 to the actuator test mode.
• Item 20: Indicator lamp 1: ON
MB991910
• The brake warning light illuminates.
MB991824 • Item 21: Indicator lamp 1: OFF
• The brake warning light goes out.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the check result normal?
YES : Go to Step 3.
NO : Replace the combination meter (Refer to GROUP
54A, Combination meter assembly P.54A-131).

MB991827
AC404789AB

STEP 3. Check the parking brake switch.

Refer to P.35A-18.
Q: Is the parking brake switch normal?
YES : Go to Step 4.
NO : Replace the parking brake switch. then go to Step
Step 9.

STEP 4. Check the brake fluid level switch.

Refer to GROUP 35A, On-vehicle Service −Brake Fluid Level
Switch Check P.35A-18.
Q: Is the parking brake fluid level switch normal?
YES : Go to Step 5.
NO : Replace the brake fluid level switch. then go to Step
Step 9.

TSB Revision
 PARKING BRAKES
PARKING BRAKE DIAGNOSIS
36-11

STEP 5. Check parking brake switch connector C-16, brake

fluid level switch connector A-04, intermediate connector
C-24 and combination meter connector C-04 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
CONNECTOR: A-04 Q: Are the connectors and terminals in good condition?
YES : Go to Step 6.
NO : Repair or replace the faulty connector. (Refer to
A-04 (GR) HARNESS SIDE GROUP 00E, Harness Connector Inspection
P.00E-2). Then go to Step 9.

AC406432 BA

CONNECTORS: C-04, C-24

C-04
C-04 HARNESS SIDE

C-24

C-24 AC406442CO

CONNECTOR: C-16

HARNESS SIDE

C-16 (B)
AC406444 DB

TSB Revision
36-12 PARKING BRAKES
PARKING BRAKE DIAGNOSIS

STEP 6. Check the harness wire parking brake switch

connector C-16 terminal 1 and combination meter
connector C-04 terminal 9 for damage.
CONNECTOR: C-04 Q: Are the harness wires in good condition?
YES : Go to Step 7.
NO : Repair the damaged harness wire. Then go to Step 9.
HARNESS SIDE

AC406442AB

CONNECTOR: C-16

HARNESS SIDE

C-16 (B)
AC406444 DB

STEP 7. Check the harness wire brake fluid level switch

connector A-04 terminal 1 and combination meter
connector C-04 terminal 9 for damage.
CONNECTOR: A-04 Q: Are there harness wires in good condition?
YES : Go to Step 8.
NO : Repair the damaged harness wire. Then go to Step 9.
A-04 (GR) HARNESS SIDE

AC406432 BA

CONNECTOR: C-16

HARNESS SIDE

C-16 (B)
AC406444 DB

TSB Revision
 PARKING BRAKES
ON-VEHICLE SERVICE
36-13

STEP 8. Retest the system

Q: Does the brake warning light turn off when the parking
brake lever is release?
YES : It can be assumed that this malfunction is intermittent.
(Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points −How to
Cope with Intermittent Malfunction P.00-14).
NO : Replace the combination meter (Refer to GROUP
54A, Combination meter assembly P.54A-131).

STEP 9. Retest the system

Q: Does the brake warning light turn off when the parking
brake lever is released?
YES : The procedure is complete.
NO : Return to Step 1.

ON-VEHICLE SERVICE
PARKING BRAKE LEVER STROKE CHECK AND
ADJUSTMENT
M1361000900533
1. Pull the parking brake lever with a force of approximately
200 N (45 pounds) and count the number of notches.
Standard value: 5 −7 notches
2. If the parking brake lever stroke is not within the standard
value, adjust as described below.
(1) Release the parking brake.
<INSIDE THE FLOOR CONSOLE> (2) Remove the console inner box tray and plate (Refer to
GROUP 52A, Floor Console Assembly P.52A-28), and
CABLE ROD
then loosen the adjusting nut to move it to the cable rod
end so that the cable will be free.

ADJUSTING
NUT
AC405950 AB

(3) Remove the rear wheels, and then remove the

adjustment hole plug on the brake disc.

ADJUSTMENT
HOLE PLUG
AC209383AB

TSB Revision
36-14 PARKING BRAKES
ON-VEHICLE SERVICE

(4) Use a flat-tip screwdriver to turn the adjuster in the

direction of the arrow (the direction which expands the
ADJUSTER
shoe) so that the disc will not rotate by hand. Return the
adjuster five notches in the direction opposite to the
direction of the arrow.
(5) Install the rear wheels, and then tighten the wheel nuts to
98 ± 10 Nm (73 ± 7 ft-lb).
BRAKE DISC
CAUTION
Be sure that the parking brake lever stroke is within the
AC206725 AB standard value. If the stroke is too short, brake drag will
result.
<INSIDE THE FLOOR CONSOLE> (6) Turn the adjusting nut to adjust the parking brake lever
stroke to the standard value. After adjustment, check that
CABLE ROD
the adjust nut and the cable rod are not loose.
(7) Release the parking brake and turn the rear wheels to
check that the rear brakes are not dragging.
3. If either of the parking brake cables is replaced, adjust the
parking brake lever stroke as described previously, pull the
parking brake lever 10 times with approximately 200 N (45
ADJUSTING pounds) to eliminate the initial slack of the cable. Then
NUT
AC405950 AB adjust the parking brake lever stroke again as described
previously.

PARKING BRAKE SWITCH CHECK

M1361003300626
1. Remove the floor console (Refer to GROUP 52A, Floor
Console P.52A-28).
2. Check for continuity between the parking brake switch
terminal and the switch mounting bolt.
When parking brake lever is pulled 2 ohms or less
When parking brake lever is released Open circuit

AC405951

TSB Revision
 PARKING BRAKES
ON-VEHICLE SERVICE
36-15
PARKING BRAKE LINING SEATING PROCEDURE
M1361001100392

CAUTION
Perform lining seating in a place with good visibility, and
pay special attention to safety.
Perform lining seating by the following procedure when replac-
ing the parking brake shoe assemblies or the rear brake discs,
or when brake performance is insufficient.
1. Adjust the parking brake lever stroke to the standard value
(Refer to P.36-13).
PULL 2. Hook a spring scale onto the center of the parking brake
lever grip and pull it with a force of 98 −147 N (22 −33
pounds) in a direction perpendicular to the handle.
3. Drive the vehicle at a constant speed of 35 −50 km/h (22 −31
SPRING SCALE
mph) for 100 meters (328 feet).
4. Release the parking brake and let the brakes cool for five to
ten minutes.
5. Repeat the procedure in steps 2. to 4. four to five times.
APPROXIMATELY
40 mm (1.6 in) ACX00701AC

TSB Revision
36-16 PARKING BRAKES
PARKING BRAKE LEVER

PARKING BRAKE LEVER

REMOVAL AND INSTALLATION
M1361001300534

Pre-removal Operation Post-installation Operation

Rear Floor Console Assembly and Rear Console Bracket • Parking Brake Lever Stroke Adjustment (Refer to
Removal (Refer to GROUP 52A, Floor Console P.52A-28). P.36-13).
• Rear Console Bracket and Rear Floor Console Assembly
Installation (Refer to GROUP 52A, Floor Console
P.52A-28).

1 3
5
2

AC406109AB

SECTION A - A SECTION B - B

A RATCHET
PAWL

B
A
RATCHET
PAWL

REMOVAL STEPS
1. ADJUSTING NUT
2. PARKING BRAKE SWITCH
CONNECTOR
3. PARKING BRAKE CABLE
CONNECTION
4. PARKING BRAKE LEVER
ASSEMBLY
5. PARKING BRAKE SWITCH

TSB Revision
 PARKING BRAKES
PARKING BRAKE CABLE
36-17
PARKING BRAKE CABLE
REMOVAL AND INSTALLATION
M1361001900893

Pre-removal Operation Post-installation Operation

• Floor Console Assembly Removal (Refer to GROUP 52A, • Floor Console Assembly Installation (Refer to GROUP
Floor Console Assembly P.52A-28). 52A, Floor Console Assembly P.52A-28).
• Parking Brake Lever Stroke Check and Adjustment (Refer
to P.36-13).

2N

AC405954 AB

REMOVAL STEPS
• SHOE ASSEMBLY (REFER TO P.36-18).
• REAR PARKING BRAKE CABLE TO
BACKING PLATE CONNECTION
(REFER TO P.36-18).
• FRONT PARKING BRAKE CABLE TO
REAR PARKING BRAKE CABLE
CONNECTION (REFER TO P.36-16).
1. REAR PARKING BRAKE CABLE
2. O-RING

TSB Revision
36-18 PARKING BRAKES
PARKING BRAKE LINING AND DRUM

PARKING BRAKE LINING AND DRUM

REMOVAL AND INSTALLATION
M1361002500490

Post-installation Operation
• Parking Brake Lever Stroke Check and Adjustment (Refer
to P.36-13).
• Parking Brake Lining Seating (Refer to P.36-15).

60 ± 5 N·m
45 ± 3 ft-lb 1
73 ± 7 N·m
54 ± 5 ft-lb
2

N 12
14
10
15 13
4
3
19 7
11

18 17
16
8
9 5
6
AC306238AB

13 :

13 18 6

BRAKE GREASE: BRAKE GREASE SAE J310, NLGI No.1

REMOVAL STEPS REMOVAL STEPS (Continued)

<<A>> 1.
REAR BRAKE BOLT 11. REAR PARKING BRAKE CABLE
<<A>> 2.
REAR BRAKE CALIPER CONNECTION
ASSEMBLY 12. O-RING
<<B>> 3. REAR BRAKE DISC 13. REAR BRAKE SHOE ASSEMBLY
>>C<< 4. SHOE-TO-ANCHOR SPRING <<C>> >>A<< 14. REAR BRAKE CHAMBER
5. ADJUSTING WHEEL SPRING RETAINER
>>B<< 6. REAR BRAKE SHOE SLACK 15. REAR BRAKE WASHER
ADJUSTER 16. PARKING BRAKE OPERATING
7. PARKING BRAKE OPERATING LEVER
LEVER STRUT • REAR WHEEL SPEED SENSOR
8. STRUT-TO- SHOE SPRING (REFER TO GROUP 35B, WHEEL
9. REAR BRAKE SHOE SPRING SPEED SENSOR P.35B-145).
CUP AND SHOE HOLD-DOWN 17. REAR WHEEL HUB ASSEMBLY
SPRING 18. BACKING PLATE
10. PARKING BRAKE CABLE CLIP 19. SHOE HOLD-DOWN PIN

TSB Revision
 PARKING BRAKES
PARKING BRAKE LINING AND DRUM
36-19
REMOVAL SERVICE POINTS
.

<<A>> REAR BRAKE BOLT/REAR BRAKE CALI-

PER ASSEMBLY REMOVAL
Remove the rear brake caliper assembly and support it with
wire or something similar.
.

<<B>> REAR BRAKE DISC REMOVAL

If the rear brake disc is seized, install M8× 1.25 bolts as shown,
and remove the rear brake disc by tightening the bolts evenly
and gradually.

BOLTS
(M8 × 1.25)
AC205986AB

<<C>> REAR BRAKE CHAMBER RETAINER

REMOVAL
Use a flat-tipped screwdriver or a similar tool to open up the
PIN OF REAR BRAKE
SHOE ASSEMBLY rear brake chamber retainer joint. Then remove the rear brake
chamber retainer.

REAR BRAKE CHAMBER

RETAINER AC000924 AD

INSTALLATION SERVICE POINTS

.

>>A<< REAR BRAKE CHAMBER RETAINER

INSTALLATION
PIN OF REAR BRAKE Use pliers or a similar tool to close the rear brake chamber
SHOE ASSEMBLY retainer end onto the pin.

REAR BRAKE CHAMBER

RETAINER AC000926 AF

TSB Revision
36-20 PARKING BRAKES
PARKING BRAKE LINING AND DRUM

>>B<< REAR BRAKE SHOE SLACK ADJUSTER

INSTALLATION
LEFT SIDE WHEEL Install the rear brake shoe slack adjuster as shown.

REAR

REAR BRAKE SHOE

SLACK ADJUSTER AC206987AB

RIGHT SIDE WHEEL

FRONT

REAR BRAKE SHOE

SLACK ADJUSTER AC206987 AC

>>C<< SHOE-TO-ANCHOR SPRING

INSTALLATION
CAUTION
LEFT SIDE WHEEL
The front and rear shoe-to-anchor springs are not inter-
REAR changeable, so the blue spring must be installed at the
front side and the yellow spring must be installed at the
rear side.
Install the shoe-to-anchor springs in the order shown in the
illustration.
1 (BLUE SPRING)

2 (YELLOW SPRING)
AC206986 AB

RIGHT SIDE WHEEL

REAR

1 (BLUE SPRING)

2 (YELLOW SPRING)
AC209387AB

TSB Revision
 PARKING BRAKES
PARKING BRAKE LINING AND DRUM
36-21
INSPECTION
M1361002600260

PARKING BRAKE LINING AND BRAKE DRUM

CHECK
1. Measure the thickness of the brake lining at several places.
Standard value: 2.8 mm (0.11 inch)
Minimum Limit: 1.0 mm (0.04 inch)
2. If the thickness of the brake lining is below the limit, replace
the shoe assemblies on both sides of the vehicle. Never
replace only one side.

ACX00708AB

3. Measure the inside diameter of the brake disc in two places

or more.
Standard value: 168.0 mm (6.61 inches)
Limit: 169.0 mm (6.65 inches)
4. If the inside diameter exceeds the limit, or if it is excessively
worn on one side, replace the brake disc.

ACX00709AB

TSB Revision
36-22 PARKING BRAKES
SPECIFICATIONS

SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
M1361003500266

ITEM SPECIFICATION
Parking brake lining and drum
Rear brake bolt (rear brake caliper assembly mounting 60 ± 5 N⋅ m (45 ± 3 ft-lb)
bolt)
Rear wheel hub assembly mounting bolt 73 ± 7 N⋅ m (54 ± 5 ft-lb)

SERVICE SPECIFICATIONS
M1361000300650

ITEM STANDARD VALUE LIMIT

Parking brake lever stroke 5 −7 notches −
[Parking brake lever pull force: Approximately 200 N
(45 pounds)]
Rear brake lining thickness mm (in) 2.8 (0.11) Minimum 1.0 (0.04)
Brake drum inside diameter mm (in) 168.0 (6.61) 169.0 (6.65)

LUBRICANT
M1361000400301

ITEM SPECIFIED LUBRICANT

Rear brake shoe slack adjuster Brake grease SAE J310, NLGI No.1
Backing plate
Rear brake shoe assembly

TSB Revision