We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
You are on page 1/ 6
To determine Resistance Per Cm Of a Given Wire by Plotting
a graph Of Potential Difference Versus Current.
Aim
To determine resistance per cm of a given wire by plotting a graph of potential
difference versus current
Apparatus
A resistance wire, a voltmeter (0-3) V and an ammeter (0-3) A of appropriate range, a
battery (battery eliminator), a rheostat, a metre scale, one way key, connecting wires
and a piece of sand paper.
Theory
According to the Ohm's law the current flowing through a conductor is directly
proportional to the potential difference across its ends provided the physical conditions
(temperature, dimensions, pressure) of the conductor remains the same. If | be the
current flowing through a conductor and V be the potential difference across its ends,
then according to, Ohm's Law,
leV
Vel or V=RI
where, R is the constant of proportionality. It is known as resistance of the conductor.
..Working formula
or T
R depends upon the nature of material, temperature and dimensions of the conductor.
In S.1 units, the potential difference V is measured in volt and the current | in ampere,
the resistance R is measured in ohm.
(1) To establish the current-voltage relationship, it is to be shown that the
ratio V/l remains constant for a given resistance, therefore a graph between the
potential difference (V) and the current (/) must be a straight line.
5 v
(2) The constant ratio gives unknown value of resistance, (F R)Circuit diagram
iH
Procedure
1
. Arrange the apparatus in the same manner as given in the arrangement diagram.
2. Clean the ends of the connecting wires with sand paper to remove the insulations,
if any.
Make neat, clean and tight connections according to the circuit diagram. While
making connections ensure that +ve marked terminals of voltmeter and ammeter
are joined towards the +ve terminal of the battery.
Determine the least count of voltmeter and ammeter, and also note the zero error,
if any.
Insert the key K, slide the rheostat contact and see that ammeter and voltmeter
are
working properly.
Adjust the sliding contact of the rheostat such that a measurable current passes
through the resistance coil or the resistance wire.
Note down the value of potential difference V" from voltmeter and current | from
ammeter.
Shift the rheostat contact slightly so that both ammeter and voltmeter show full
divisions readings and not in fraction.
Record the readings of the voltmeter and ammeter.
Note. In case of battery eliminator, follow these steps:
Turn the knob at 2 V in battery eliminator and put the constant point in rheostat at
fixed position. Now record the reading in voltmeter and ammeter.
Without disturbing the rheostat, tum the knob of battery to different voltage such
that 4, 6, 8, 10 and 12 Volts and record corresponding readings in voltmeter and
ammeter.
10. Take at least five sets of independent observations.11.Cut the resistance wire at the points where it leaves the terminals, stretch it and
find its length by the metre scale,
12. Record your observations.
+
Observations
1. Length
Length of the resistance wire /= ..
2. Range
Range of the given ammete
Range of the given voltmete
3. Least count
Least count of ammeter = .
Least count of voltmeter
4, Zero error
Zero error in ammeter, €; = .........
Zero error in voltmeter, @: = .....5. Zero correction
Zero correction for ammeter, ¢;
Zero correction for voltmeter, c2
6. Table for Ammeter and Voltmeter
Readings
‘Voltmeter reading ‘Ammeter reading
A unchanged decreases
B. decreases increases
G increases unchanged
D. unchanged increases
Calculations
1. Find ratio of V and | for each set of observations.
2. Plot a graph between potential difference V (column 36) and current | (column 26),
taking V along X-axis and | along Y-axis. The graph comes to be a straight lineGraph between potential difference
and current. It is a straight line.
From graph, the resistance can be calculated.
cot 8 = ——
but
then,
rane
3. Constant ratio 7 gives resistance of the wire.
4, Resistance of the wire per cm =...... Q em,
Result
1. Resistance per om of the wire is ........ Qcm'.
2. The graph between V and /is a straight line
Al)
+=(2)
+n(3)
wl)Precautions
1
2.
3.
4,
5.
The connections should be neat, clean and tight.
Thick copper wires should be used for the connections after removing the
insulations near their ends by rubbing with sand paper.
Voltmeter and ammeter should be of proper range.
A low resistance rheostat should be used.
The key should be inserted only while taking observations to avoid heating of
resistance (otherwise its resistance will increase).
Sources of error
1
2.
3.
The instrument screws may be loose
Thick connecting wires may not be available.
Rheostat may have high resistance.