DESIGN MANUAL 2.

sealmaticindia.com
 Contents
1 Industrial Applications Page 1-2

2 Standard Cartridge Seals Page 3-22

3 Mechanical Seals As Per API 682 Page 23-26

4 Split Seals Page 27-32

5 Engineered Seals For Demanding Applications Page 33-39

6 Standard Mechanical Seals For Pumps & Compressors Page 40-66

7 Gas Lubricated Seals for Pumps & Agitators Page 67-72

8 Mechanical Seals for Agitators, Mixers, Kneaders & Reactors Page 73-83

9 Supply Systems & Components Page 84-98

10 Technical Information Page 99-107

Disclaimer:
The specifications, drawings, images etc included in this catalogue are intended to be generic and must be interpreted as equivalent or functionally
equivalent. The identification of many items are facilitated by illustrations (photographs and general assembly drawings) and mention of, or reference
to any specific standards, or trade names, including those that might appear on the photographs, drawings, images etc is intended for illustration
purposes only, and does not imply an endorsement or imitation or preference of any specific standard, brand, manufacturer or supplier. Neither does
the information imply the availability of any mentioned items. The items discussed alongwith the images, drawings etc portrayed are representative of
industry catalogues, standards, terminology and specifications & hence accounting for any resemblance which otherwise may be co-incidental.
This Catalogue does not contain any guarantee or agreed quality of products or any warranty of merchantability, fitness for a particular purpose and
non-infringement. The data and information contained herein are being provided for information only and without responsibility, and Sealmatic India
Pvt. Ltd. makes no representations or warranties, either expressed or implied, as to the accuracy, completeness, or fitness for a particular purpose.
Sealmatic does not accept any responsibility or liability with regard to the reliance on, or use of this data and information.
Sealmatic is continuously improving and upgrading their products with respect to quality and application and therefore any changes made to the
catalogue may be made without any notice.
 Industrial Applications
Onshore Offshore Compressors

To be able to cope with sand, water and gases found in Adverse environmental conditions, high rotational speed High speed machines whose trouble free availability
crude oil, pumping systems for mineral oil require and pressure levels as well as corrosive media constitutes a major precondition for many process
heavy duty pumps with reliable engineered constituents place demanding requirements on sealing engineering operations. Key criteria for the selection
mechanical seals that feature durable sliding faces technology used in the offshore production and and design of compressors are the working medium,
with good emergency running characteristics. Often it subsequent conveyance of oil and gas. Not only that but the compression ratio, the volume flow, the number of
is necessary to seal pressures in excess of 100 bar and in many cases highly abrasive mixtures of crude oil, intermediate inputs & outputs and the design of the
sliding velocities of over 60 m/s. The ideal seal face water, gas and sand cause a high degree of wear. shaft seal which assumes critical importance.
combination for such conditions have proven to be Sealmatic has proven itself with its heavy-duty
Typical Applications
high-strength carbons running against silicon carbide. mechanical seals with innovative and tailor made seal
components with high-strength seal faces , guaranteeing  Ammonia Compressor
Typical Applications
longer service life even in highly stressed pumps.  CO Compressor
 Crude Oil Pump Typical Applications  Oven Gas Compressor
 Pipeline Pump  Ethylene Compressor
 Main Oil Export Pump
 Water Injection Pump  Flash Turbine
 Multiphase Pump
 Screw Compressor
 Water Injection Pump

Quarrying & Coal Mining Coal Gasification Chemical & Petrochemical

The cutter heads on quarrying and mining machines There were times, particularly during the oil-crisis The materials used in the chemical/petrochemical
are fed with water, not only for cooling purposes but years, when coal gasification centered on the process industry need to be capable of coping with the large
also for settling the dust and extinguishing any sparks of hydrogenation, e.g. to produce motor fuels. array of media, many of them explosive or toxic and
produced by the cutting tools. Mechanical Seals Nowadays the driving force behind its further others which could become when mixed. An increased
perform the dual function of a rotary joint and a seal for development is the generation of electricity by awareness of environmental risks calls for a maximum
the cutter and roller heads. Sealing systems used on combination-type power stations with integrated coal reliability and operational safety, especially from
these equipment are exposed to abrasive and gasification. Here the main objectives are to lower CO2 sealing systems. Against this background, the sealing
chemically aggressive media. In some applications, emissions, to raise fuel efficiency and to stretch systems used in applications involving what are in
high temperature and pressure make conditions even existing resources. many cases explosive, toxic or aggressive media have
more challenging. Despite the harsh operating to ensure optimum tightness. On the other hand they
Typical Applications
environment, users expect high reliability to avoid should also help optimize processes and thus be of
costly downtime.  Coal Feed Screw advantage where the economic aspects are
concerned as well. From non-critical sealing points –
Typical Applications for which standard solutions are deployed – right
 Cutter Head Seal through to highly complex system solutions required
where particularly difficult operating conditions are
 Mining Machine concerned.
 Roller Head Seal
Typical Applications
 Rotary Joint For Carbide Cutter  Agitator Bead Mill
 Chemical Pump
 Eccentric Screw Pump
 Gear Pump
 Glass Lined Reactor
 Thin Film Evaporator
 Centrifuge
 Chemical Reactor
1
 Industrial Applications

Refinery Sugar Pharmaceutical

The processing of crude oil in refineries is a complex Sugar campaigns are over in a relatively short time. For In addition to meeting technical requirements a seal
and multi-stage process in which crude oil is optimum economy and ecology it is all the more has to display many other characteristics in connection
transformed into refined, high-quality end products or important, therefore to have a reliable sealing systems. with cleanliness, health and general legislation. These
feed materials for petrochemical industry. Sealing In the past it was normal for juice pumps to be equipped include for example materials which are compatible
technology for such diverse applications have to meet with double seals to cope with the tendency to with food, smooth and abrasion-proof surfaces which
challenges in various respects; risk of insufficient crystallization and carbonation. Today the use of single are easy to clean, complete units which can be
lubrication and dry running, media with a diversity of seals is possible in most of the cases due to availability sterilized and cleaned without having to be dismantled
physical properties, high and low temperature ranges of modern materials and new seal compartment (SIP/CIP). Sealmatic mechanical seals have been
and the handling of hazardous substances and all geometries. used for such demanding applications with great
other conditions which need to be controlled with success in sterile processes. Our range of mechanical
absolute reliability. With a comprehensive range of Typical Applications seals includes a broad spectrum of high-quality,
API-compliant quality seals and supply systems,  Flume Water Pump specifically optimized sealing solutions ranging from
Sealmatic is playing a key role towards ensuring the  Juice Circulating Pump standard solutions to specialized system solutions for
reliability and safety of refinery processes.  Worm Agitator nearly any application in the pharmaceutical industry.
Typical Applications  Mash Pump Typical Applications
 Discharge Pump  Agglomerator
 Gas Oil Pump  Spherical Dryer
 GLP Delivery Pump  Eccentric Pump
 Quench Oil Pump  Sterile Pump
 Residual Oil Pump  Centrifugal Pump
 Filter Dryer
 Food Pump
Power Pulp & Paper Hot Water
water

Sealing systems featuring maximum operational Wood is the most important raw material for the pulp Hot water is conveyed by pumps for a variety of
reliability, convenient maintenance and low leakage and paper industry. It is either digested to chemical purposes in thermal energy generating systems,
rates with necessary environmental protective pulp in digesters or reduced to mechanical pulp in district heating systems, home heating systems and so
measures are standard requirements in modern power grinders or refiners. The pulp produced this way is then on. The suitability of a mechanical seal for such
stations. The product range includes mechanical seals graded, bleached and washed and conveyed to the applications depends on many different parameters,
and supply systems for auxiliary and secondary paper machine. There it passes through the various e.g. pressure to be sealed, temperature at the seal,
pumps, boiler circulation pumps and feedwater pumps stages such as head box, wire part, press section, sliding velocity, power consumption, water quality (pH-
as well as mechanical seals and carbon floating ring drying section and reeling section. value, O2-dose, conductivity, operating mode), water
seals for turbines, compressors and fans.
additives such as corrosion inhibitors etc.
Typical Applications
Typical Applications
 Pressure Grinder
 Boiler Circulating Pump
 Feed Pump  Pulp Pump
 Flue Gas Desulphurisation  Digesting & Bleaching Pump
 Residue Evacuation Pump  Deinking Pump
 Condensate Pump

2
CTX ANSI Single Seals Standard Cartridge Seals

Product Description Technical Features

1. Single seal configuration 1. Ideal for use in ANSI process pumps
2. Balanced design 2. O-ring is dynamically loaded to prevent
3. Independent of direction of rotation shaft damage.
4. Cartridge construction 3. Dimensional modification of the stuffing
5. Available for standard (CTX-ASPN) box chamber is not required due to
and big bore (CTX-ABPN) seal short radial installation height
chambers 4. Ideal to convert and retrofit pumps with
6. Single seals with flush (-ASPN, -ABPN) packings and large volume OEM
and with quench combined with lip seal production
(-ASQN, - ABQN) or throttle ring 5. Cartridge unit factory assembled for
(-ASTN, -ABTN) easy installation, which reduces down-
time
6. Rugged design for long operating life

l1 Typical Industrial Applications

ANSI process pumps
l2 Chemical industry
Food and beverage industry
l3 l4 Petrochemical industry
Pharmaceutical industry
Universally applicable
Water and waste water technology
Standards
ANSI
Materials
Seal face: Silicon carbide (Q1), Carbon
graphite resin impregnated (B), Tungsten
13 carbide (U2)
12 Seat: Silicon carbide (Q1)
Secondary seals: FKM (V), EPDM (E),
FFKM (K), Perflourocarbon rubber/PTFE (U1)
Springs: Hastelloy® C-4 (M)
7 5 4 1 8 10 Metal parts: CrNiMo steel (G), CrNiMo cast steel (G)
max

min

h6
d2

Performance Capabilities
d3

d3

d1

CTX-ASPN, -ABPN, -ASTN, -ABTN, -ASQN, -ABQN

6 14 11 2 3 9 Sizes: d1 = 1.000" ... 3.750"
Other sizes on request
Temperature: t= -40°C ...+220°C (-40°F ...+428°F)
(Check O-ring resistance)
Sliding face material combination BQ1
Pressure: p1 = 25 bar (363 PSI)
Speed = 16 m/s (52 ft/s)
Sliding face material combination Q1Q1 or U2Q1
Pressure: p1 = 12 bar (175 PSI)
Speed = 10 m/s (33 ft/s)
Permissible axial movement: ± 1.0 mm, d1 > 75 mm
± 1.5 mm

Item Description Item Description

Note: The item numbers as depicted above are based on our technical experience and 1 Seal face 10 Snap ring
knowledge and are placed in the chronological order of their assembly procedure.
2, 5, 7 O-ring 11 Cover
3 Spring 12 Assembly fixture
4 (remove after installation)
Seat
13 HSH Cap Screw
6 Shaft sleeve
14 Gasket
8 Drive collar
16 Lip seal (-QN), throttle ring (-TN)
9 Set screw

3
Installation, Details, Options Product Variants
l15 l15
O
45 O l17 l16
45
l17 l16

16 16

max

min
max

min

d3

d3
d3

d3
da
a1

CTX-ASTN and -ABTN CTX-ASQN and -ABQN

Single seal for operation with unpressurized Single seal for operation with unpressurized
quench for standard (S) and big bore (B) seal quench for standard (S) and big bore (B) seal
chambers. Same as CTX-ASPN and -ABPN but chambers. Same as CTX-ASPN and -ABPN
with throttle ring (item 16). The cover has version but with lip seal (item 16) at the
auxiliary connections for flushing and quench. atmospheric side. The cover has auxiliary
Throttle ring: PTFE carbongraphite reinforced connections for flushing and quench.
(T12). Lip seal: NBR (P), FKM (V), PTFE carbon
reinforced (T3)
Dimensional Data
BIG BORE : Dimensions in inch
d1 d2 d3 min d3 max l1 l2 l3 l4 l15 l16 l17 a1 da s Connection
1.000 - - - - - - - - - - - - - -
1.125 1.713 1.752 2.795 2.638 1.669 0.969 1.000 2.937 1.909 1.028 3.311 4.500 0.437 1/4 NPT
1.250 - - - - - - - - - - - - - -
1.375 1.960 2.000 3.189 2.638 1.669 0.969 1.000 2.947 1.919 1.028 3.543 5.118 0.437 1/4NPT
1.500 - - - - - - - - - - - - - -
1.625 - - - - - - - - - - - - - -
1.750 2.461 2.500 4.055 2.638 1.669 0.969 1.000 3.012 1.984 1.028 4.567 6.496 0.559 3/8 NPT
1.875 2.583 2.661 3.937 2.638 1.669 0.969 1.000 3.071 2.059 1.012 4.409 5.984 0.551 3/8 NPT
2.000 2.677 2.756 4.567 2.638 1.929 0.709 1.000 3.130 2.102 1.028 4.882 6.260 0.551 3/8 NPT
2.125 2.834 2.913 4.528 2.638 1.669 0.969 1.000 3.012 1.984 1.028 5.276 6.890 0.709 3/8 NPT
2.250 2.960 3.093 4.409 2.638 1.945 0.693 1.276 3.130 2.102 1.028 4.685 6.417 0.709 3/8 NPT
2.500 3.212 3.299 5.276 2.638 1.919 0.719 1.250 3.130 2.102 1.028 5.512 7.795 0.709 3/8 NPT
2.625 3.338 3.170 5.118 2.638 1.919 0.719 1.250 3.130 2.102 1.028 5.354 6.890 0.709 3/8 NPT
2.750 3.660 3.740 5.236 2.638 1.945 0.693 1.276 3.130 2.102 1.028 5.512 7.480 0.630 3/8 NPT
3.000 3.937 4.016 5.512 3.307 2.276 1.031 1.276 3.858 2.516 1.343 5.906 8.228 0.650 3/8 NPT
3.250 - - - - - - - - - - - - - -

STANDARD BORE : Dimensions in inch

d1 d2 d3 min d3 max l1 l2 l3 l4 l15 l16 l17 a1 da s Connection
1.000 1.693 1.732 2.205 2.638 1.669 0.969 1.000 2.937 1.909 1.028 2.756 3.937 0.433 1/4 NPT
1.125 1.713 1.752 2.205 2.638 1.669 0.969 1.000 2.937 1.909 1.028 2.440 4.134 0.437 1/4 NPT
1.250 1.969 2.008 2.402 2.638 1.669 0.969 1.000 3.130 2.102 1.028 2.638 4.252 0.433 1/4 NPT
1.375 1.961 2.000 2.402 2.638 1.669 0.969 1.000 2.947 1.919 1.028 2.760 4.213 0.437 1/4 NPT
1.500 2.200 2.244 2.717 2.638 1.669 0.969 1.000 3.130 2.102 1.028 2.950 4.488 0.551 3/8 NPT
1.625 2.340 2.421 2.795 2.638 1.669 0.969 1.000 3.130 2.102 1.028 3.030 4.921 0.551 3/8 NPT
1.750 2.461 2.500 2.953 2.638 1.669 0.969 1.000 3.012 1.984 1.028 3.228 5.118 0.559 3/8 NPT
1.875 2.583 2.661 3.070 2.638 1.669 0.969 1.000 3.071 2.043 1.028 3.190 5.118 0.551 3/8 NPT
2.000 2.677 2.756 3.189 2.638 1.669 0.969 1.000 3.130 2.102 1.028 3.430 5.472 0.630 3/8 NPT
2.125 2.834 2.913 3.583 2.638 1.669 0.969 1.000 3.012 1.984 1.028 3.820 5.512 0.650 3/8 NPT
2.250 2.960 3.039 3.583 2.638 1.669 0.969 1.000 3.130 2.102 1.028 3.858 5.866 0.650 3/8 NPT
2.375 3.070 3.125 3.590 2.638 1.669 0.969 1.000 - - - 4.020 6.181 0.709 3/8 NPT
2.500 3.212 3.291 3.937 2.638 1.669 0.969 1.000 3.130 2.102 1.028 4.528 6.693 0.709 3/8 NPT
2.625 3.338 3.417 4.016 2.638 1.669 0.969 1.000 3.130 2.102 1.028 4.528 6.378 0.630 3/8 NPT
2.750 3.660 3.740 4.370 2.638 1.929 0.709 1.000 3.130 2.102 1.028 4.646 7.441 0.709 3/8 NPT
3.000 3.937 4.016 4.724 3.307 2.260 1.047 1.000 3.858 2.516 1.343 5.000 7.835 0.709 3/8 NPT
3.250 4.189 4.268 4.921 3.307 2.260 1.047 1.000 3.858 2.516 1.343 5.315 7.830 0.709 3/8 NPT
3.750 4.689 4.750 5.433 3.307 2.260 1.047 1.000 - - - 5.827 8.189 0.866 3/8 NPT

Note: Additional technical & dimensional information will be provided on request.

4
CTX Single Seals Standard Cartridge Seals

Product Description Technical Features

1. Single seal configuration 1. Ideal for use in process pump
2. Balanced design standardization
3. Independent of direction of rotation 2. O-ring is dynamically loaded to prevent
4. Cartridge construction shaft damage.
3. Dimensional modification of the stuffing
box chamber is not required due to
short radial installation height
4. Ideal to convert and retrofit pumps with
packings and large volume OEM
production
5. Cartridge unit factory assembled for
easy installation, which reduces down-
time
6. Rugged design for long operating life

l1 Typical Industrial Applications

Chemical industry
l2 Food and beverage industry
Petrochemical industry
Pharmaceutical industry
l3 l4 Universally applicable
Water and waste water technology
Centrifugal pumps
Eccentric screw pumps
Process pumps
Materials
Seal face: Silicon carbide (Q1), Carbon
graphite resin impregnated (B), Tungsten
13 carbide (U2)
12 Seat: Silicon carbide (Q1)
Secondary seals: FKM (V), EPDM (E),
FFKM (K), Perflourocarbon rubber/PTFE (U1)
Springs: Hastelloy® C-4 (M)
7 5 4 1 8 10 Metal parts: CrNiMo steel (G), CrNiMo cast
h6

steel (G)
d2
d3

d1

Performance Capabilities
6 14 11 2 3 9 CTX-SN, -SNO, -QN, -TN
Sizes: d1 = Upto 100 mm (Upto 4.000")
Other sizes on request
Temperature: t= - 40°C ...+220°C
(-40°F ...+428°F)
(Check O-ring resistance)
Sliding face material combination BQ1
Pressure: p1 = 25 bar (363 PSI)
Speed = 16 m/s (52 ft/s)
Sliding face material combination Q1Q1 or
U2Q1
Pressure: p1 = 12 bar (175 PSI)
Speed = 10 m/s (33 ft/s)
Permissible axial movement: ± 1.0 mm, d1 > 75
Note: The item numbers as depicted above are based on our technical experience and mm ± 1.5 mm
knowledge and are placed in the chronological order of their assembly procedure.

Item Description Item Description

1 Seal face 10 Snap ring
2, 5, 7 O-ring 11 Cover
3 Spring 12 Assembly fixture
4 Seat 13 HSH Cap Screw
6 Shaft sleeve 14 Gasket
8 Drive collar 16 Lip seal (-QN),
9 Set screw throttle ring (-TN)

5
 Installation, Details, Options Design Variations
l15
l15
l13 l12 l17 l16
l17 l16
O
45 O l14
45
A

16 16

da
CTX-SNO CTX-TN CTX-QN
Single seal without Single seal for operation with Single seal for operation with
connections, for dead-end unpressurized quench. Same unpressurized quench. Same
operation. as CTX-SN but with throttle as "-SN' version but with
a1

ring (item 16). The cover has outboard lip seal (item 16). The
auxiliary connections for cover has auxiliary connections
flushing and quench. for flushing and quench.
Throttle ring: PTFE carbon- Lip seal: NBR (P), FKM (V),
graphite reinforced (T12). PTFE carbon reinforced (T3).
Dimensional Data
Dimensions in inch
d1 d2 d3min. d3 max. l1 l2 l3 l4 l 12 l13 l14 l15 l16 l17 a1 da s
1.000 1.693 1.750 2.000 2.640 1.669 0.969 1.000 1.378 1.260 0.689 3.130 2.102 1.028 2.440 4.134 0.520
1.125 1.811 1.875 2.050 2.640 1.669 0.969 1.000 1.378 1.260 0.689 3.130 2.102 1.028 2.440 4.134 0.520
1.250 1.960 2.000 2.250 2.640 1.669 0.969 1.000 1.378 1.260 0.689 3.130 2.102 1.028 2.640 4.330 0.520
1.375 2.086 2.125 2.420 2.640 1.669 0.969 1.000 1.378 1.260 0.689 3.130 2.102 1.028 2.750 4.449 0.520
1.500 2.200 2.250 2.625 2.640 1.669 0.969 1.000 1.378 1.260 0.689 3.130 2.102 1.028 2.950 4.842 0.520
1.625 2.340 2.375 2.700 2.640 1.669 0.969 1.000 1.378 1.260 0.689 3.130 2.102 1.028 3.030 4.842 0.599
1.750 2.460 2.500 2.812 2.640 1.669 0.969 1.000 1.378 1.260 0.689 3.130 2.102 1.028 3.190 5.433 0.599
1.875 2.582 2.625 2.940 2.640 1.669 0.969 1.000 1.378 1.260 0.689 3.130 2.102 1.028 3.307 5.433 0.599
2.000 2.677 2.750 3.190 2.640 1.669 0.969 1.000 1.378 1.260 0.689 3.130 2.102 1.028 3.430 5.827 0.599
2.125 2.834 2.875 3.437 2.640 1.669 0.969 1.000 1.378 1.260 0.689 3.130 2.102 1.028 3.543 5.827 0.709
2.250 2.960 3.000 3.560 2.640 1.669 0.969 1.000 1.378 1.260 0.689 3.130 2.102 1.028 3.940 6.181 0.709
2.375 3.070 3.125 3.590 2.640 1.669 0.969 1.000 1.378 1.260 0.689 3.130 2.102 1.028 4.020 6.181 0.709
2.500 3.212 3.250 3.800 2.640 1.669 0.969 1.000 1.378 1.260 0.689 3.130 2.102 1.028 4.170 6.417 0.709
2.625 3.338 3.375 3.937 2.640 1.669 0.969 1.000 1.378 1.260 0.689 3.130 2.102 1.028 4.290 6.417 0.709
2.750 3.660 3.750 4.250 2.640 1.669 0.969 1.000 1.378 1.260 0.689 3.130 2.102 1.028 4.650 7.008 0.709
2.875 3.937 4.000 4.646 3.307 2.260 1.047 1.000 1.815 1.492 0.866 - - - 5.079 7.480 0.709
3.000 3.937 4.000 4.646 3.307 2.260 1.047 1.000 1.815 1.492 0.866 3.858 2.516 1.343 5.079 7.480 0.709
3.125 4.190 4.125 4.764 3.307 2.260 1.047 1.000 1.815 1.492 0.866 3.858 2.516 1.343 5.315 7.677 0.709
3.250 4.189 4.250 4.882 3.307 2.260 1.047 1.000 1.815 1.492 0.866 - - - 5.315 7.677 0.709
3.375 4.311 4.375 5.039 3.307 2.260 1.047 1.000 1.815 1.492 0.866 - - - 5.472 7.795 0.866
3.500 4.437 4.500 5.157 3.307 2.260 1.047 1.000 1.815 1.492 0.866 - - - 5.591 7.795 0.866
3.625 4.563 4.625 5.315 3.307 2.260 1.047 1.000 1.815 1.492 0.866 - - - 5.709 8.071 0.866
3.750 4.689 4.750 5.433 3.307 2.260 1.047 1.000 1.815 1.492 0.866 3.858 2.516 1.343 5.827 8.189 0.866
4.000 4.937 5.000 5.669 3.307 2.260 1.047 1.000 1.815 1.492 0.866 - - - 6.063 8.583 0.866
Dimensions in millimeter
d1 d2 d3 min. d3 max. l1 l2 l3 l4 l 12 l13 l14 l15 l16 l17 a1 da s
25 43.0 44.0 51.5 67 42.4 24.6 25.4 35.0 32.0 17.5 79.5 53.4 26.1 62 105 13.2
28 46.0 47.0 52.0 67 42.4 24.6 25.4 35.0 32.0 17.5 79.5 53.4 26.1 62 105 13.2
30 48.0 49.0 56.0 67 42.4 24.6 25.4 35.0 32.0 17.5 79.5 53.4 26.1 65 105 13.2
32 50.0 51.0 57.0 67 42.4 24.6 25.4 35.0 32.0 17.5 79.5 53.4 26.1 67 108 13.2
33 50.0 51.0 57.0 67 42.4 24.6 25.4 35.0 32.0 17.5 79.5 53.4 26.1 67 108 13.2
35 53.0 54.0 61.5 67 42.4 24.6 25.4 35.0 32.0 17.5 79.5 53.4 26.1 70 113 13.2
38 56.0 57.0 66.0 67 42.4 24.6 25.4 35.0 32.0 17.5 79.5 53.4 26.1 75 123 13.2
40 58.0 59.0 68.0 67 42.4 24.6 25.4 35.0 32.0 17.5 79.5 53.4 26.1 75 123 14.2
42 60.5 61.5 69.5 67 42.4 24.6 25.4 35.0 32.0 17.5 79.5 53.4 26.1 79 133 14.2
43 60.5 61.5 70.5 67 42.4 24.6 25.4 35.0 32.0 17.5 79.5 53.4 26.1 79 133 14.2
45 62.5 64.0 73.0 67 42.4 24.6 25.4 35.0 32.0 17.5 79.5 53.4 26.1 81 138 14.2
48 65.6 67.0 75.0 67 42.4 24.6 25.4 35.0 32.0 17.5 79.5 53.4 26.1 84 138 14.2
50 68.0 69.0 78.0 67 42.4 24.6 25.4 35.0 32.0 17.5 79.5 53.4 26.1 87 148 18.0
53 72.0 73.0 87.0 67 42.4 24.6 25.4 35.0 32.0 17.5 79.5 53.4 26.1 97 148 18.0
55 73.0 74.0 83.0 67 42.4 24.6 25.4 35.0 32.0 17.5 79.5 53.4 26.1 90 148 18.0
60 78.0 79.0 91.0 67 42.4 24.6 25.4 35.0 32.0 17.5 79.5 53.4 26.1 102 157 18.0
65 83.1 85.7 98.5 67 42.4 24.6 25.4 35.0 32.0 17.5 79.5 53.4 26.1 109 163 18.0
70 93.0 95.0 108.0 67 42.4 24.6 25.4 35.0 32.0 17.5 79.5 53.4 26.1 118 178 18.0
75 100.0 101.6 118.0 84 57.4 26.6 25.4 46.1 37.9 22.0 98.0 63.9 34.1 129 190 18.0
80 106.4 108.0 124.0 84 57.4 26.6 25.4 46.1 37.9 22.0 98.0 63.9 34.1 135 195 18.0
85 109.5 111.1 128.0 84 57.4 26.6 25.4 46.1 37.9 22.0 98.0 63.9 34.1 139 198 22.0
90 115.9 117.5 135.0 84 57.4 26.6 25.4 46.1 37.9 22.0 98.0 63.9 34.1 145 205 22.0
95 119.1 120.7 138.0 84 57.4 26.6 25.4 46.1 37.9 22.0 98.0 63.9 34.1 148 208 22.0
100 125.4 127.0 144.0 84 57.4 26.6 25.4 46.1 37.9 22.0 98.0 63.9 34.1 154 218 22.0
Note: Additional technical & dimensional information will be provided on request.
6
CTX ANSI Dual Seals Standard Cartridge Seals

Product Description Technical Features

1. Dual seal configuration 1. Ideal for use in ANSI process pumps
2. Balanced design 2. O-ring is dynamically loaded to prevent
3. Independent of direction of rotation shaft damage.
4. Cartridge construction 3. Dimensional modification of the stuffing
5. Available for standard (CTX-ASDN) box chamber is not required due to
and big bore (CTX-ABDN) seal short radial installation height
chambers 4. Ideal to convert and retrofit pumps with
6. Double pressure balanced packings and large volume OEM
7. Designed with integrated pumping production
device for increased efficiency in 5. Cartridge unit factory assembled for
circulation easy installation, which reduces down-
time
6. Rugged design for long operating life

Typical Industrial Applications

ANSI process pumps
Chemical industry
5
Food and beverage industry
Petrochemical industry
( 6)
7 Pharmaceutical industry
Universally applicable
4 Water and waste water technology

Standards
ANSI

Materials
Seal face: Silicon carbide (Q1), Carbon
20 graphite resin impregnated (B), Tungsten
carbide (U2)
Seat: Silicon carbide (Q1)
Secondary seals: FKM (V), EPDM (E),
FFKM (K), Perfluorocarbon rubber/PTFE (U1)
Springs: Hastelloy® C-4 (M)
Metal parts: CrNiMo steel (G), CrNiMo cast
6 4 1 2 10 9 12 15 16 17 steel (G)

Item Description
d3 max
d3 min

d1 h6
d2

1 Seal face
2, 5, 7, O-ring
10, 13,
15
7 5 8 3 11 13 14 19 18 3 Spring
4 Seat
6 Shaft sleeve
8 Cover
9 Seal face
11 Spring
12 Seat
14 Drive collar
16 Set screw
17 Snap ring
18 Assembly fixture
Note: The item numbers as depicted above are based on our technical experience and
knowledge and are placed in the chronological order of their assembly procedure. 19 HSH Cap Screw
20 Gasket
21 Screw plug
22 Gasket

7
 Performance Capabilities Installation, Details, Options
Sizes: d1 = 1.000" .... 3.750"
Other sizes on request 45 45
Temperature: t= -40 °C ... +220 °C (- 40 °F ... +428 °F)
(Check O-ring resistance)
Sliding face material combination BQ1
LBO LBI
Pressure: p1 = 25 bar (363 PSI)
Speed = 16 m/s (52 ft/s) da
Sliding face material combination Q1Q1 or U2Q1
Pressure: p1 = 20 bar (290 PSI) 21

V
Speed = 10 m/s (33 ft/s)
Barrier fluid circulation system:
p3max = 25 bar (363 PSI)
Δp (p3 - p1) ideal = 2 ... 3 bar (29 ... 44 PSI),
7 bar (102 PSI) for barrier media with poor lubricating properties) 22
Pump startup:
Δp (p3 - p1)max = 25 bar (363 PSI) allowed
LBO
Recommended supply medium: max. ISO VG 5 LBI
a s
Permissible axial movement: ± 0.039", d1 > 2.953" ± 0.059" 2

Dimensional Data
BIG BORE - Dimensions in inch
d1 d2 d3 min. d3 max. l4 l5 l6 l7 a2 da s Connection
1.000 - - - - - - - - - - -
1.125 1.713 1.752 2.795 1.000 3.228 1.886 1.343 3.311 4.500 0.437 1/4 NPT
1.250 - - - - - - - - - - -
1.375 1.960 2.000 3.189 1.000 3.406 2.083 1.323 3.543 5.118 0.437 1/4 NPT
1.500 - - - - - - - - - - -
1.625 - - - - - - - - - - -
1.750 2.461 2.500 4.055 1.000 3.406 2.083 1.323 4.567 6.496 0.559 3/8 NPT
1.875 2.583 2.661 3.937 1.000 3.406 2.083 1.323 4.409 5.984 0.551 3/8 NPT
2.000 2.677 2.756 4.567 1.260 3.406 2.102 1.303 4.882 6.260 0.551 3/8 NPT
2.125 2.834 2.913 4.528 1.000 3.406 2.102 1.303 5.276 6.890 0.709 3/8 NPT
2.250 2.960 3.093 4.409 1.276 3.406 2.102 1.303 4.685 6.417 0.709 3/8 NPT
2.500 3.212 3.299 5.276 1.250 3.406 2.102 1.303 5.512 7.795 0.709 3/8 NPT
2.625 3.338 3.170 5.118 1.250 3.406 2.102 1.303 5.354 6.890 0.709 3/8 NPT
2.750 3.660 3.740 5.236 1.276 3.406 2.102 1.303 5.512 7.480 0.630 3/8 NPT
3.000 3.937 4.016 5.512 1.276 3.406 2.516 1.303 5.906 8.228 0.650 3/8 NPT
3.250 - - - - - - - - - - -

STANDARD BORE - Dimensions in inch

d1 d2 d3 min. d3 max. l4 l5 l6 l7 a2 da s Connection
 1.693 1.732 2.205 1.000 3.406 2.102 1.303 2.441 3.937 0.433 1/4 NPT
 1.713 1.752 2.205 1.000 3.228 3.228 1.343 2.441 4.134 0.437 1/4 NPT
 1.969 2.008 2.402 1.000 3.406 2.102 1.303 2.756 4.252 0.433 1/4 NPT
 1.961 2.000 2.402 1.000 3.406 2.083 1.303 2.756 4.213 0.437 1/4 NPT
 2.200 2.244 2.717 1.000 3.406 2.102 1.303 2.953 4.488 0.551 3/8 NPT
 2.340 2.421 2.795 1.000 3.406 2.102 1.303 3.091 4.921 0.551 3/8 NPT
 2.461 2.500 2.953 1.000 3.406 2.102 1.303 3.228 5.118 0.559 3/8 NPT
 2.583 2.661 3.070 1.000 3.406 2.102 1.303 3.307 5.118 0.551 3/8 NPT
 2.677 2.756 3.189 1.000 3.406 2.102 1.303 3.425 5.472 0.630 3/8 NPT
 2.834 2.913 3.583 1.000 3.406 2.102 1.303 3.819 5.512 0.650 3/8 NPT
 2.960 3.039 3.583 1.000 3.406 2.102 1.303 3.858 5.866 0.650 3/8 NPT
 3.070 3.125 3.590 1.000 - - - - 6.181 0.709 3/8 NPT
 3.212 3.291 3.937 1.122 3.406 2.102 1.303 4.528 6.693 0.709 3/8 NPT
 3.338 3.417 4.016 1.250 3.406 2.102 1.303 4.528 6.378 0.630 3/8 NPT
 3.660 3.740 4.370 1.260 3.406 2.102 1.303 4.646 7.441 0.709 3/8 NPT
 3.937 4.016 4.724 1.260 4.252 2.516 1.736 5.000 7.835 0.709 3/8 NPT
 4.189 4.268 4.921 1.260 4.252 2.516 1.736 5.315 7.830 0.709 3/8 NPT
 4.689 4.750 5.433 1.000 - - - - 8.189 0.866 3/8 NPT
Note: Additional technical & dimensional information will be provided on request.
8
CTX Dual Seals Standard Cartridge Seals

Product Description Technical Features

1. Dual seal configuration 1. Ideal for use in process pump
2. Balanced design standardization
3. Independent of direction of rotation 2. O-ring is dynamically loaded to prevent
4. Cartridge construction shaft damage.
5. Double pressure balanced 3. Dimensional modification of the stuffing
6. Designed with integrated pumping box chamber is not required due to
device for increased efficiency in short radial installation height
circulation 4. Ideal to convert and retrofit pumps with
7. Special design available for eccentric packings and large volume OEM
screw pumps production
5. Cartridge unit factory assembled for
easy installation, which reduces down-
time
6. Rugged design for long operating life

( 6)
7

20

6 4 1 2 10 9 12 15 16 17
Item Description
1 Seal face
d3 max
d3 min

2, 5, 7, 10, 13, 15 O-ring

d1 h6
d2

3 Spring
4 Seat
6 Shaft sleeve
7 5 8 3 11 13 14 19 18 8 Cover
9 Seal face
11 Spring
12 Seat
14 Drive collar
16 Set screw
17 Snap ring
18 Assembly fixture
19 HSH Cap Screw
20 Gasket
Note: The item numbers as depicted above are based on our technical experience and
knowledge and are placed in the chronological order of their assembly procedure. 21 Screw plug
22 Gasket

9
 Typical Industrial Applications Performance Capabilities Installation, Details, Options
Chemical industry Sizes: d1 = Upto 100 mm (Upto 4.000’’)
Food and beverage industry Other sizes on request
45 45
Petrochemical industry Temperature: t= - 40 °C ... +220 °C
Pharmaceutical industry (- 40 °F ... +428 °F)
Universally applicable (Check O-ring resistance) LBO LBI
Water and waste water technology Sliding face material combination BQ1 da
Centrifugal pumps Pressure: p1 = 25 bar (363 PSI)
Eccentric screw pumps 21
Speed = 16 m/s (52 ft/s)

V
Sliding face material combination Q1Q1 or
Materials
U2Q1
Seal face: Silicon carbide (Q1), Carbon Pressure: p1 = 20 bar (290 PSI) 22
graphite resin impregnated (B), Tungsten Speed = 10 m/s (33 ft/s)
carbide (U2) Barrier fluid circulation system:
Seat: Silicon carbide (Q1) LBI LBO
p3max = 25 bar (363 PSI) s
Secondary seals: FKM (V), EPDM (E),

a
2

FFKM (K), Perfluorocarbon rubber/PTFE (U1) Δp (p3 - p1) ideal = 2 ... 3 bar (29 ... 44 PSI),
Springs: Hastelloy® C-4 (M) 7 bar (102 PSI) for barrier media with poor
Metal parts: CrNiMo steel (G), CrNiMo cast lubricating properties)
steel (G) Pump startup:
Δp (p3 - p1)max = 25 bar (363 PSI) allowed
Recommended supply medium: max. ISO VG 5
Permissible axial movement: ± 1.0 mm,
d1 > 75 mm ± 1.5 mm
Dimensional Data
Dimensions in inch
d1 d2 d 3 min. d 3 max. l4 l5 l6 l7 a2 da s
1.000 1.693 1.732 2.008 1.000 3.400 2.102 1.303 2.440 4.134 0.520
1.125 1.811 1.875 2.050 1.000 3.400 2.102 1.303 2.402 4.134 0.520
1.250 1.961 2.008 2.244 1.000 3.400 2.102 1.303 2.760 4.330 0.520
1.375 2.087 2.216 2.421 1.000 3.400 2.102 1.303 2.840 4.449 0.520
1.500 2.205 2.244 2.598 1.000 3.400 2.102 1.303 2.950 4.843 0.520
1.625 2.343 2.375 2.700 1.000 3.400 2.102 1.303 3.090 4.842 0.559
1.750 2.461 2.520 2.874 1.000 3.400 2.102 1.303 3.230 5.433 0.559
1.875 2.582 2.638 2.953 1.000 3.400 2.102 1.303 3.350 5.433 0.559
2.000 2.677 2.717 3.071 1.000 3.400 2.102 1.303 3.430 5.827 0.559
2.125 2.835 2.874 3.425 1.000 3.400 2.102 1.303 3.819 5.827 0.709
2.250 2.961 3.000 3.560 1.000 3.400 2.102 1.303 3.940 6.181 0.709
2.375 3.071 3.125 3.583 1.000 3.400 2.102 1.303 4.020 6.181 0.709
2.500 3.213 3.300 3.800 1.000 3.400 2.102 1.303 4.180 6.417 0.709
2.625 3.339 3.374 3.937 1.000 3.400 2.102 1.303 4.303 6.417 0.709
2.750 3.661 3.740 4.252 1.000 3.400 2.102 1.303 4.660 7.008 0.709
2.875 3.937 4.000 4.646 1.000 4.250 2.516 1.736 5.079 7.480 0.709
3.000 3.937 4.000 4.646 1.102 4.250 2.516 1.736 5.079 7.480 0.709
3.125 4.189 4.252 4.882 1.102 4.250 2.516 1.736 5.315 7.677 0.709
3.250 4.189 4.252 4.882 1.102 4.250 2.516 1.736 5.315 7.677 0.709
3.375 4.311 4.375 5.039 1.102 4.250 2.516 1.736 5.472 7.795 0.866
3.500 4.437 4.500 5.517 1.102 4.250 2.516 1.736 5.591 7.795 0.866
3.625 4.563 4.625 5.315 1.102 4.250 2.516 1.736 5.709 8.071 0.866
3.750 4.689 4.752 5.433 1.102 4.250 2.516 1.736 5.827 8.189 0.866
4.000 4.937 5.000 5.669 1.102 4.250 2.516 1.736 6.063 8.583 0.866
Dimensions in millimeter
d1 d2 d 3 min. d 3 max. l4 l5 l6 l7 a2 da s
25 43.0 44.0 51.5 25.4 86.5 53.4 33.1 62 105 13.2
28 46.0 47.0 52.0 25.4 86.5 53.4 33.1 61 105 13.2
30 48.0 49.0 56.0 25.4 86.5 53.4 33.1 67 105 13.2
32 49.8 51.0 57.0 25.4 86.5 53.4 33.1 70 108 13.2
33 49.8 51.0 57.0 25.4 86.5 53.4 33.1 70 108 13.2
35 53.0 54.0 61.5 25.4 86.5 53.4 33.1 72 113 13.2
38 56.0 57.0 66.0 25.4 86.5 53.4 33.1 75 123 13.2
40 58.0 59.0 68.0 25.4 86.5 53.4 33.1 77 123 14.2
42 61.0 62.0 69.5 25.4 86.5 53.4 33.1 80 133 14.2
43 61.0 62.0 70.5 25.4 86.5 53.4 33.1 80 133 14.2
45 62.5 64.0 73.0 25.4 86.5 53.4 33.1 82 138 14.2
48 65.6 67.0 75.0 25.4 86.5 53.4 33.1 85 138 16.0
50 68.0 69.0 78.0 25.4 86.5 53.4 33.1 87 148 16.0
53 72.0 73.0 87.0 25.4 86.5 53.4 33.1 97 148 18.0
55 73.0 74.0 83.0 25.4 86.5 53.4 33.1 92 148 18.0
60 78.0 79.0 91.0 25.4 86.5 53.4 33.1 102 157 18.0
65 84.8 85.7 98.5 25.4 86.5 53.4 33.1 109 163 18.0
70 93.0 95.0 108.0 25.4 86.5 53.4 33.1 118 178 18.0
75 100.0 101.6 118.0 28.0 108.0 63.9 44.1 129 190 18.0
80 106.4 108.0 124.0 28.0 108.0 63.9 44.1 135 195 18.0
85 109.5 111.1 128.0 28.0 108.0 63.9 44.1 139 198 22.0
90 115.9 117.5 135.0 28.0 108.0 63.9 44.1 145 205 22.0
95 119.1 120.7 138.0 28.0 108.0 63.9 44.1 148 208 22.0
100 125.4 127.0 144.0 28.0 108.0 63.9 44.1 154 218 22.0
Note: Additional technical & dimensional information will be provided on request.
10
 ETX Single Seals Standard Cartridge Seals

Product Description Technical Features

1. Single seal configuration 1. Ideal for use in process pump
2. Balanced design standardization
3. Independent of direction of rotation 2. O-ring is dynamically loaded to prevent
4. Cartridge construction shaft damage.
5. Available with flush and quench 3. Dimensional modification of the stuffing
connections box chamber is not required due to
short radial installation height
4. Ideal to convert and retrofit pumps with
packings and large volume OEM
production
5. Cartridge unit factory assembled for
easy installation, which reduces down-
time
6. Rugged design for long operating life

l1
Typical Industrial Applications
l2 Chemical industry
l3
Food and beverage industry
l4
Petrochemical industry
Pharmaceutical industry
Process Pumps
Water and waste water technology

Materials
Seal face: Silicon carbide (Q1), Carbon
graphite resin impregnated (B), Tungsten
carbide (U2)
Seat: Silicon carbide (Q1)
Secondary seals: FKM (V), EPDM (E),
FFKM (K), Perflourocarbon rubber/PTFE (U1)
Springs: Hastelloy® C-4 (M)
Metal parts: CrNiMo steel (G), CrNiMo cast
steel (G)
7 4 1 2 12 13 10
Performance Capabilities
ETX-SN
d3 max.
d3 min.

Sizes: Upto 70 mm (2.75")

d1
d2

Other sizes on request

Temperature: t = -40 °C...+220 °C
(- 40 °F...+428 °F)
6 5 15 11 3 9 8 (Check O-ring resistance)
Sliding face material combination BQ1
Pressure: p1 = 20 bar (290 PSI)
Speed = 11.2 m/s
Permissible axial movement: ± 1.0 mm

Item Description Item Description

1 Seal face 10 Snap ring
2, 5, 7 O-ring 11 Cover
3 Spring 12 Assembly fixture
(remove after installation)
4 Seat
13 HSH Cap Screw
l5 6 Shaft sleeve
14 Plug
8 Drive collar
15 Gasket
9 Set screw
Note: The item numbers as depicted above are based on our technical experience and
knowledge and are placed in the chronological order of their assembly procedure.

11
 Installation, Details, Options
s

14

SH
FL U

da
IN
D RA
a1

Dimensional Data
Dimensions in inches
d1 d2 d3 min. d3 max. l1 l2 l3 l4 l5 a1 da s Connnection
1.000 1.851 1.929 2.402 2.244 1.496 0.748 0.846 0.531 2.480 4.134 0.511 1/8" NPT
1.125 1.930 2.047 2.480 2.244 1.496 0.748 0.846 0.531 2.480 4.134 0.511 1/8" NPT
1.250 2.048 2.126 2.559 2.244 1.496 0.748 0.846 0.531 2.678 4.134 0.511 1/8" NPT
1.375 2.126 2.244 2.677 2.244 1.496 0.748 0.846 0.531 2.796 4.567 0.511 1/8" NPT
1.500 2.245 2.441 2.874 2.244 1.496 0.748 0.846 0.531 2.993 4.961 0.590 1/8" NPT
1.625 2.402 2.598 3.031 2.244 1.496 0.748 0.846 0.531 3.150 5.276 0.590 1/8" NPT
1.750 2.520 2.677 3.110 2.244 1.496 0.748 0.846 0.531 3.229 5.552 0.590 1/8" NPT
1.875 2.638 2.795 3.228 2.244 1.496 0.748 0.846 0.531 3.347 5.552 0.590 1/8" NPT
2.000 2.835 3.031 3.465 2.244 1.496 0.748 0.846 0.531 3.662 5.945 0.709 1/8" NPT
2.125 2.914 3.110 3.543 2.244 1.496 0.748 0.846 0.531 3.662 5.945 0.709 1/8" NPT
2.250 3.032 3.228 3.661 2.244 1.496 0.748 0.846 0.531 3.780 6.142 0.709 1/8" NPT
2.375 3.111 3.425 3.858 2.244 1.496 0.748 0.846 0.531 3.977 6.339 0.709 1/8" NPT
2.500 3.229 3.543 3.976 2.244 1.496 0.748 0.846 0.531 4.095 6.536 0.709 1/8" NPT
2.625 3.426 3.819 4.252 2.244 1.496 0.748 0.846 0.531 4.370 6.733 0.709 1/8" NPT
2.750 3.504 4.213 4.646 2.244 1.496 0.748 0.846 0.531 4.764 7.126 0.709 1/8" NPT

Dimensions in millimeter
d1 d2 d3 min. d3 max. l1 l2 l3 l4 l5 a1 da s Connnection
25 44 49 60 57 38 19 21.5 13.5 63 105 13 1/8" NPT
28 47 50 60 57 38 19 21.5 13.5 64 105 13 1/8" NPT
30 49 52 63 57 38 19 21.5 13.5 66 105 13 1/8" NPT
33 52 54 65 57 38 19 21.5 13.5 68 105 13 1/8" NPT
35 54 57 68 57 38 19 21.5 13.5 71 116 13 1/8" NPT
38 57 62 73 57 38 19 21.5 13.5 76 126 15 1/8" NPT
40 59 62 73 57 38 19 21.5 13.5 76 126 15 1/8" NPT
42 61 66 77 57 38 19 21.5 13.5 80 134 15 1/8" NPT
43 62 67 78 57 38 19 21.5 13.5 81 134 15 1/8" NPT
45 64 68 79 57 38 19 21.5 13.5 82 141 15 1/8" NPT
48 67 71 82 57 38 19 21.5 13.5 85 141 15 1/8" NPT
50 69 74 85 57 38 19 21.5 13.5 88 141 15 1/8" NPT
52 72 77 88 57 38 19 21.5 13.5 91 151 18 1/8" NPT
53 72 77 88 57 38 19 21.5 13.5 91 151 18 1/8" NPT
55 74 79 90 57 38 19 21.5 13.5 93 151 18 1/8" NPT
58 77 82 93 57 38 19 21.5 13.5 96 156 18 1/8" NPT
60 79 87 98 57 38 19 21.5 13.5 101 161 18 1/8" NPT
63 82 90 101 57 38 19 21.5 13.5 104 166 18 1/8" NPT
65 84 92 103 57 38 19 21.5 13.5 106 166 18 1/8" NPT
68 87 97 108 57 38 19 21.5 13.5 111 171 18 1/8" NPT
70 89 107 118 57 38 19 21.5 13.5 121 181 18 1/8" NPT

Note: Additional technical & dimensional information will be provided on request

12
 UTX Single Seals Standard Cartridge Seals

Product Description Technical Features

1. Single seal configuration 1. Ideal for use in process pump
2. Unbalanced design standardization
3. Independent of direction of rotation 2. Flushing connection according to API
4. Cartridge construction 682, Plan 11 for seal chamber cleaning
and cooling
3. Low cost cartridge solution
4. Dimensional modification of the stuffing
box chamber is not required due to
short radial installation height
5. Ideal to convert and retrofit pumps with
packings and large volume OEM
production
6. Cartridge unit factory assembled for
easy installation, which reduces down-
time
7. Rugged design for long operating life

l1 Typical Industrial Applications

l3 l2 Water and waste water technology
Sewage water
Cold and hot water
Cooling fluids
Beverages
Circulating pumps
Water and waste water pumps
Materials
Seal face: Carbon graphite resin impregnated (B),
Silicon carbide (Q1)
Seat: Silicon carbide (Q1)
Secondary seals: FKM (V), EPDM (E)
7 6 5 1.2 1.1 3 4 11 12 Metal parts: CrNiMo steel (G),
h6

CrNiMo cast steel (G)

d9
d3
d2

dN

2 9 1.3 1.4 8 10 Performance Capabilities

Sizes: Upto 75 mm (1" … 2.625")
Pressure: p1 = 12 bar (174 PSI)
Temperature: t = - 20 °C…+ 140 °C
13 (- 4 °F…+284 °F)
Speed = 10 m/s (33 ft/s)
14 Axial movement: ± 0.5 mm
Stationary Seats
l6
l5
20 O

l4

Note: The item numbers as depicted above are based on our technical experience and
knowledge and are placed in the chronological order of their assembly procedure.
l28
d 6 H11

d7 H 8

l10
Item Description Item Description
1 Bellows unit 6 Shaft sleeve
1.1 Seal face 7 O-ring G6 (EN 12756)
1.2 Bellows 8 Cover
1.3 Drive collar 9 Gasket
1.4 L-ring (spring collar) 10 Drive collar
2 Spring 11 Set screw
3 Seat 12 Snap ring
4 O-ring or L-ring 13 Assembly fixture
5 Spacer ring 14 HSH Cap Screw

13
 o
45 45 o

da

s
Dimensional Data

Dimensions in inch
dN d2 d3 min d3 max d9 da a s l1 l2 l3 l4 t
1.000 1.512 1.634 2.000 2.362 4.134 2.440 0.520 2.579 1.614 0.965 0.906 1/4 NPT
1.125 1.669 1.750 2.050 2.362 4.134 2.441 0.520 2.677 1.634 1.043 0.906 1/4 NPT
1.250 1.772 1.890 2.250 2.559 4.331 2.638 0.520 2.736 1.654 1.083 0.906 1/4 NPT
1.375 1.933 2.000 2.420 2.677 4.213 2.756 0.520 2.854 1.732 1.122 1.024 1/4 NPT
1.500 2.020 2.146 2.625 2.874 4.843 2.950 0.579 2.854 1.732 1.122 1.024 1/4 NPT
1.750 2.354 2.480 2.812 3.110 5.118 3.230 0.559 3.012 1.752 1.260 1.024 1/4 NPT
1.875 2.433 2.559 2.940 3.228 5.118 3.307 0.559 3.071 1.772 1.299 1.024 1/4 NPT
2.000 2.551 2.677 3.190 3.346 5.827 3.430 0.579 3.169 1.850 1.319 1.102 3/8 NPT
2.125 2.795 2.875 3.437 3.740 5.512 3.820 0.689 3.287 1.850 1.437 1.102 3/8 NPT
2.250 2.874 2.992 3.560 3.780 6.181 3.858 0.689 3.287 1.850 1.437 1.102 3/8 NPT
2.375 3.012 3.110 3.590 3.937 6.181 4.020 0.689 3.366 1.850 1.516 1.102 3/8 NPT
2.500 3.209 3.287 3.800 4.173 6.693 4.252 0.689 3.465 1.909 1.555 1.102 3/8 NPT
2.625 3.268 3.374 3.937 4.252 6.378 4.331 0.689 3.465 1.909 1.555 1.102 3/8 NPT

Dimensions in millimeter
dN d2 d3 min d3 max d6 d7 d9 da a s l1 l2 l3 l4 l5 l6 l 10 l 28 t
25 38.4 41.5 51.0 34.0 40 60 105 62 13.2 65.5 41.0 24.5 23 2 5 8.5 7.5 1/4 NPT
28 42.4 44.5 52.0 37.0 43 60 105 62 13.2 68.0 41.5 26.5 23 2 5 8.5 7.5 1/4 NPT
30 42.4 45.5 56.0 39.0 45 63 105 67 13.2 68.0 41.5 26.5 23 2 5 8.5 7.5 1/4 NPT
32 45 .0 48.0 57.2 42.0 48 65 110 67 13.2 69.5 42.0 27.5 23 2 5 8.5 7.5 1/4 NPT
33 45.0 48.0 57.0 42.0 48 65 110 67 13.2 69.5 42.0 27.5 23 2 5 8.5 7.5 1/4 NPT
35 49.1 50.8 61.5 44.0 50 68 107 70 13.2 72.5 44.0 28.5 26 2 5 8.5 7.5 1/4 NPT
38 51.3 54.5 66.0 49.0 56 73 123 75 14.7 72.5 44.0 28.5 26 2 6 10 9 1/4 NPT
40 54.3 57.5 68.0 51.0 58 75 123 77 14.7 75.5 44.5 31.0 26 2 6 10 9 1/4 NPT
43 56.3 59.5 70.5 54.0 61 78 133 80 14.7 76.5 44.5 32.0 26 2 6 10 9 1/4 NPT
45 61.0 63.0 73.0 56.0 63 79 130 82 14.2 76.5 44.5 32.0 26 2 6 10 9 1/4 NPT
48 61.8 65.0 75.0 59.0 66 82 130 84 14.2 78.0 45.0 33.0 26 2 6 10 9 1/4 NPT
50 64.8 68.0 78.0 62.0 70 85 148 87 14.7 80.5 47.0 33.5 28 2.5 6 10.5 9.5 3/8 NPT
53 71.0 73.0 87.0 65.0 73 95 148 97 17.5 81.5 47.0 34.5 28 2.5 6 12 11 3/8 NPT
55 71.0 73.0 83.0 67.0 75 90 148 92 17.5 83.5 47.0 36.5 28 2.5 6 12 11 3/8 NPT
60 76.5 79.0 91.0 72.0 80 100 157 102 17.5 85.5 47.0 38.5 28 2.5 6 12 11 3/8 NPT
65 83.0 85.7 98.5 77.0 85 108 162 110 17.5 88.0 48.5 39.5 28 2.5 6 12 11 3/8 NPT
70 88.0 94.0 108.0 83.0 92 116 178 118 17.5 92.0 48.5 43.5 28 2.5 7 12.5 11.3 3/8 NPT
75 93.4 98.4 118.0 88.0 97 125 190 127 17.5 93.5 49.0 44.5 28 2.5 7 12.5 11.3 3/8 NPT
80 97.0 115.0 125.0 95.0 105 131 202 134 18.0 93.5 49.0 45.5 28 3 7 13 12 3/8 NTP
Note: Additional technical & dimensional information will be provided on request

14
 MTX Single Seals Standard Cartridge Metal Bellows Seals

Product Description Technical Features

1. Single seal configuration 1. Ideal for use in process pump
2. Balanced design standardization
3. Independent of direction of rotation 2. Dimensional modification of the stuffing
4. Cartridge construction box chamber is not required due to
5. Metal bellows design short radial installation height
6. Single seal with quench and lip seal 3. Ideal to convert and retrofit pumps with
(-QN) or throttle ring (-TN) packings and large volume OEM
7. Connections for flush and quench production
available 4. Cartridge unit factory assembled for
8. Multipoint injection ring design for easy installation, which reduces down-
(-QNM, -TNM) time
5. Rugged design for long operating life
6. Bellows design efficiently ensure self-
cleaning
7. S u i t a b l e f o r h i g h t e m p e r a t u r e
applications

l1 Typical Industrial Applications

Refining technology
l2 l3 Petrochemical industry
Hot media
Cold media
Highly viscous media
Pumps
Special rotating equipment

Materials
Seal face: Carbon graphite antimony
impregnated (A), Silicon carbide (Q1)
Seat: Silicon carbide (Q1)
Secondary seals: FKM (V), EPDM (E),
FFKM (K)
Bellows: Inconel® 718 (M6)
Metal parts: CrNiMo steel (G), Duplex (G1)
3 7 6 15 4 8 11 12 Throttle ring: PTFE carbon graphite reinforced
(T12)
d3

d1
d2

Lip seal: NBR (P), PTFE carbon reinforced (T3)

2 1 5 9 10 Performance Capabilities
Shaft diameter: d1 = 25 ... 80 mm (1" … 3.15")
Temperature: t*) = - 40 °C ... +220 °C
(- 40 °F ... +428 °F)
13 Pressure: p = 25 bar (363 PSI)
*)
Operating limits of O-rings to be observed

14

l4
Item Description Item Description

Note: The item numbers as depicted above are based on our technical experience and
1 Bellows unit 9 Lip seal (-QN)
knowledge and are placed in the chronological order of their assembly procedure.
2, 5, 7 O-ring or throttle ring (-TN)
10 Drive collar
3, 11 Set screw
12 Retaining ring
4 Seat
13 Assembly fixture
6 Shaft sleeve
14 HSH Cap Screw
8 Cover
15 Gasket

15
 Installation, Details, Options Product Variants

o
45 45 o

da

A A

C B C B

s
a1

MTX-QNM MTX-TNM
Single seal, as MTX-QN with additional Single seal, as MTX-TN with additional
multipoint injection ring (item C). multipoint injection ring (item C).

Dimensional Data

Dimensions in millimeter
d1 d2 d3 min. d3 max. l1 l2 l3 l4 da a1 s
25 45.0 47.0 51.0 79.5 26.1 53.4 25.4 105.0 62.0 13.2
30 49.4 52.0 56.0 78.4 25.0 53.4 25.4 105.0 67.0 13.2
32 52.3 54.5 57.0 78.4 25.0 53.4 25.4 108.0 70.0 13.2
33 52.3 54.5 57.0 78.4 25.0 53.4 25.4 108.0 70.0 13.2
35 54.8 58.0 61.5 78.4 25.0 53.4 25.4 113.0 72.0 13.2
38 57.5 60.0 66.0 78.4 25.0 53.4 25.4 123.0 75.0 13.2
40 58.8 62.0 68.0 78.2 24.8 53.4 25.4 123.0 77.0 14.2
43 61.9 64.5 70.5 78.4 25.0 53.4 25.4 133.0 80.0 14.2
45 65.0 68.5 73.0 78.4 25.0 53.4 25.4 138.0 82.0 14.2
48 68.4 71.0 75.0 78.7 25.3 53.4 25.4 138.0 85.0 14.2
50 70.0 73.0 78.0 79.1 25.7 53.4 25.4 148.0 87.0 14.2
53 71.9 75.0 87.0 77.8 24.4 53.4 25.4 148.0 97.0 18.0
55 74.6 77.0 83.0 78.9 25.5 53.4 25.4 148.0 92.0 18.0
60 83.9 87.0 91.0 80.1 26.7 53.4 25.4 157.0 102.0 18.0
65 87.5 90.0 98.5 80.0 26.6 53.4 25.4 163.0 109.3 18.0
70 93.0 98.0 108.0 81.5 28.1 53.4 25.4 178.0 118.3 18.0
75 96.8 101.6 118.0 94.4 30.5 63.9 28.0 190.0 129.0 18.0
80 104.7 108.0 124.0 94.4 30.4 64.0 28.0 195.0 135.0 18.0
Note: Additional technical & dimensional information will be provided on request.

16
 MTX Dual Seals Standard Cartridge Metal Bellows Seals

Product Description Technical Features

1. Dual seal configuration 1. Ideal for use in process pump
2. Balanced design standardization
3. Independent of direction of rotation 2. O-ring is dynamically loaded to prevent
4. Cartridge construction shaft damage.
5. Metal bellows design 3. Dimensional modification of the stuffing
6. Designed with integrated pumping box chamber is not required due to
device for increased efficiency in short radial installation height
circulation 4. Ideal to convert and retrofit pumps with
7. Stationary O-ring design packings and large volume OEM
8. Seals with API Plan 52 and API Plan production
53/54 5. Cartridge unit factory assembled for
easy installation, which reduces down-
time
6. Rugged design for long operating life
7. Bellows design efficiently ensure self-
cleaning
8. S u i t a b l e f o r h i g h t e m p e r a t u r e
applications

Typical Industrial Applications

l5
Refining technology
Petrochemical industry
l6 l7 Hot media
Cold media
Highly viscous media
Pumps
Special rotating equipment
Materials
Seal face: Carbon graphite (A),
Silicon carbide (Q1)
Seat: Silicon carbide (Q1),
Tungsten carbide (U2)
Secondary seals: FPM (V), EPDM (E), FFKM (K)
Bellows: Inconel® 718 (M6)
Springs: Hastelloy® C-4 (M)
Metal parts: CrNiMo steel (G), Duplex (G1)
3 7 6 20 4 10 9 15 16 17 Performance Capabilities
d3

Shaft diameter: d1 = 25 ... 80 mm (1" … 3.15")

d1
d2

Temperature : t* = –40 °C ... +220 °C

(– 40 °F ... + 428 °F)
2 1 5 11 8 12 13 14
Pressure: p1 = 25 bar (232 PSI)
Speed = 20 m/s (66 ft/s)
Barrier fluid circulation system:
p3max = 16 bar (232 PSI)
Δp (p3–p1) ideal = 2 … 3 bar (29 … 44 PSI)
Δp (p3–p1) max.
18 = 10 bar (145 PSI) at <120 °C (<248 °F)
19 = 5 bar (73 PSI) at  220 °C (232 °F)
API Plan 52 (53/54)
Pump startup:
Δp (p3–p1) max.16 bar (232 PSI) allowed
* Operating limits of O-rings to be observed

l4 Item Item
Description Description
1 Bellows unit 12 Seat
Note: The item numbers as depicted above are based on our technical experience and
knowledge and are placed in the chronological order of their assembly procedure. 2, 5, 7,10, 13, 15 O-ring 14 Drive collar
3, 16 Set screw 17 Retaining ring
4 Seat 18 Assembly fixture
6 Shaft sleeve 19 HSH Cap Screw
8 Cover 20 Gasket
9 Seal face 21 Screw Plug
11 Spring 22 Gasket

17
 Installation, Details, Options Product Variants
MTX9-DN
O
45 O Dimensions, items and descriptions as for MTX-DN, but with optimized seal face geometry
45 for pressurized operation according to API Plan 53/54. A barrier fluid system (e.g.
Sealmatic BFS2000) is necessary.
Pressure: p1 = 10 bar (145 PSI)
Speed = 20 m/s (66 ft/s)
LBO LBI Barrier fluid circulation system:
p3max = 16 bar (232 PSI)
22 Δp (p3 – p1) ideal = 2 … 3 bar (29 … 44 PSI)
Δp (p3 – p1) max = 16 bar (232 PSI)
API Plan 53/54
da 21 Pump startup:
Δp (p3 – p1) max = 16 bar (232 PSI) allowed

LBI LBO
s
a2

Dimensional Data

Dimensions in millimeter
d1 d2 d3 min. d3 max. l4 l5 l6 l7 da a2 s
25 45.0 47.0 51.0 25.4 87.0 33.6 53.4 105.0 62.0 13.2
30 49.4 52.0 56.0 25.4 86.5 33.1 53.4 105.0 67.0 13.2
32 52.3 54.5 57.0 25.4 86.5 33.1 53.4 108.0 70.0 13.2
33 52.3 54.5 57.0 25.4 86.5 33.1 53.4 108.0 70.0 13.2
35 54.8 58.0 61.5 25.4 86.5 33.1 53.4 113.0 72.0 13.2
38 57.5 60.0 66.0 25.4 86.5 33.1 53.4 123.0 75.0 14.0
40 58.8 62.0 68.0 25.4 86.3 32.9 53.4 123.0 77.0 14.2
43 61.9 64.5 70.5 25.4 86.5 33.1 53.4 133.0 80.0 14.2
45 65.0 68.5 73.0 25.4 86.5 33.1 53.4 138.0 82.0 14.2
48 68.4 71.0 75.0 25.4 86.8 33.4 53.4 138.0 85.0 14.2
50 70.0 73.0 78.0 25.4 87.2 33.8 53.4 148.0 87.0 14.2
53 71.9 75.0 87.0 25.4 87.4 34.0 53.4 148.0 97.0 18.0
55 74.6 77.0 83.0 25.4 87.0 33.6 53.4 148.0 92.0 18.0
60 83.9 87.0 91.0 25.4 88.2 34.8 53.4 157.0 102.0 18.0
65 87.5 90.0 98.5 25.4 88.1 34.7 53.4 163.0 109.3 18.0
70 93.0 98.0 108.0 25.4 89.6 36.2 53.4 178.0 118.3 18.0
75 96.8 101.6 118.0 28.0 107.4 43.5 63.9 190.0 129.0 18.0
80 104.7 108.0 124.0 28.0 106.8 42.9 63.9 195.0 135.0 18.0
Note: Additional technical & dimensional information will be provided on request.

18
 CTXAPI Single & Dual Seals Standard Cartridge Seals

Product Description Technical Features

1. Single and Dual seal configuration 1. Designed to accommodate shaft
2. Balanced design deflections and process fluctuations
3. Independent of direction of rotation 2. Effi c i ent c ons truc ti on for heat
4. Cartridge construction dissipation
5. Seal design in accordance with API 682 / 3. Compact installation design
ISO 21049 4. Factory assembled cartridge unit for
6. Conforming to Category 1, Type A, easy installation
Arrangement 1, 2 or 3 5. Springs are product protected to avoid
7. Single seal with API Plan 11 and 61 contamination
8. Dual seals with API Plan 52 / 53 6. Can accommodate reverse pressure
9. Robust construction with shrink-fitted 7. Can handle extensive applications in
seal faces various temperatures and pressures
10. Heavy duty solid seat design 8. Versatile in design to fit various seal
11. Also available in design variation for chambers
independent of direction of rotation
12. Additional flushing plans available on
request

Typical Industrial Applications

Chemical industry
Light volatile and highly viscous hydrocarbons
Low solids content and low abrasive media
Media with poor lubrication properties
2 1 Oil and gas industry
Petrochemical industry
LBO Toxic and hazardous media
Standard pumps
Vertical and horizontal ANSI chemical pumps
Standards
19 API 682 / ISO 21049
Materials
23 Seal face: Carbon graphite antimony
impregnated (A), Silicon carbide sintered
(h)

pressureless (Q12)
Seat: Silicon carbide sintered pressureless (Q1)
6 7 1 4 5 17 15 18 12 13 22 24 Secondary seals: FKM (V), FFKM (K), NBR (P),
EPDM (E)
Springs: Hastelloy® C-4 (M)* and C-276 (M5)
d3 f 7

d1 h6
d2

d5
d4

Metal parts: CrNiMo steel (G)

Performance Capabilities
2 3 8 16 14 10 11 9 20 21
Sizes: d1 = Upto110 mm (Upto 4.250’’)
other sizes on request
Pressure: p1 = 22 bar (319 PSI)
Temperature: t = –40 °C...+260 °C
(–40 °F...+500 °F)
Speed = 23 m/s (75 ft /s)
d

Item Description
1, 9 Seal face
2, 5, 7, 10, 13, O-ring
LBI
15, 16, 17
l
3, 11 Spring
4, 12 Seat
Note: The item numbers as depicted above are based on our technical experience and
knowledge and are placed in the chronological order of their assembly procedure. 6 Shaft sleeve
8 Adapter
14 Driver
18 Housing
19 HSH Cap screw
20 Set ring
21 Set screw
22 Assembly fixture
23 Hexagon bolt
24 Set screw
19
 Design Variations
2 1

FI Q

23
(h)

6 2 4 5 22 24

CTXAPI-SA
d3 f7

d 1 h6
d2

d4

d5
Single Seal

16 7 3 1 8 20 21
d

I
Note: The item numbers as depicted above are based on our technical experience and
knowledge and are placed in the chronological order of their assembly procedure.

Dimensional Data
Dimensions in millimeter

d1 d2 d3 d4 d5 l l1 l2 d n acc. to ASME B73.1

(h min)
20 50.4 58 105 127 96.5 68.5 28 13.5 4 19.05
25 55.4 63 110 132 96.5 68.5 28 13.5 4 19.05
30 60.4 68 115 137 96.5 68.5 28 13.5 4 19.05
35 65.4 73 120 142 96.5 68.5 28 13.5 4 19.05
40 70.4 78 125 147 96.5 68.5 28 13.5 4 19.05
45 75.4 83 135 162 96.5 68.5 28 17.5 4 19.05
50 80.4 88 140 167 100 72 28 17.5 4 19.05
55 85.4 93 145 172 100 72 28 17.5 4 19.05
60 96 105 160 187 127.5 88 39.5 17.5 4 22.22
65 101 110 165 192 127.5 88 39.5 17.5 4 22.22
70 106 115 170 197 127.5 88 39.5 17.5 4 22.22
75 111 120 175 202 127.5 88 39.5 17.5 4 22.22
80 116 125 185 213 127.5 88 39.5 22 4 22.22
85 123.5 136 190 223 131.5 92 39.5 22 4 25.4
90 128.5 141 195 228 131.5 92 39.5 22 4 25.4
95 133.5 146 200 233 131.5 92 39.5 22 4 25.4
100 138.5 151 205 238 131.5 92 39.5 22 4 25.4
105 143.5 156 210 243 131.5 92 39.5 22 4 25.4
110 152.5 161 215 248 131.5 92 39.5 22 4 25.4
inch size available from size 0.750 to 4.250
Note: Additional technical & dimensional information will be provided on request.
20
 VTX Single Seals For Eccentric Screw Pumps - Standard Cartridge Seals

Product Description Technical Features

1. Single seal configuration 1. Ideal for use in process pump
2. Balanced design standardization
3. Independent of direction of rotation 2. O-ring is dynamically loaded to prevent
4. Cartridge construction shaft damage.
3. Dimensional modification of the stuffing
box chamber is not required due to
short radial installation height
4. Ideal to convert and retrofit pumps with
packings and large volume OEM
production
5. Cartridge unit factory assembled for
easy installation, which reduces down-
time
6. Rugged design for long operating life

VTX
CTX seals with modified cover for eccentric screw
pumps.
Example Pumps: Seepex BN, Netzsch NM...S,
NM...B, NE (P), Allweiler AE, AEB, AED, Robbins
& Myers / Moyno 2000 CC, and Mono E-Range.
Typical Industrial Applications
Foodstuffs and animal feed industries
Sweet cider pressing and beverage production
Viticulture and wineries
Spirit production and alcohol industry
Breweries and malt houses
7 5 4 1 12 13 10 Sugar industry
Pharmaceuticals and cosmetics industry
Oil and gas industry
Pulp and paper production
Paint and lacquer industry
Chemicals industry
Automobile industry
Water and wastewater industry
6 11 2 3 8 9 Materials
Seal face: Silicon carbide (Q1), Carbon
graphite resin impregnated (B), Tungsten
carbide (U2)
Seat: Silicon carbide (Q1)
Secondary seals: FKM (V), EPDM (E),
FFKM (K), Perflourocarbon rubber/PTFE (U1)
Springs: Hastelloy® C-4 (M)
Metal parts: CrNiMo steel (G), CrNiMo cast
steel (G)

Performance Capabilities
Note: The item numbers as depicted above are based on our technical experience and VTX-SN, -SNO, -QN, -TN
knowledge and are placed in the chronological order of their assembly procedure. Sizes: Upto 100 mm (Upto 4.000")
Other sizes on request
Temperature: t= – 40 °C...+220 °C
Item Description Item Description (–40 °F...+428 °F)
(Check O-ring resistance)
1 Seal face 10 Snap ring
Sliding face material combination Bq1
2, 5, 7 O-ring 11 Cover Pressure: p1 = 25 bar (363 PSI)
3 Spring 12 Assembly fixture Speed = 16 m/s (52 ft/s)
4 13 Sliding face material combination Q1Q1 or
Seat HSH Cap Screw
U2Q1
6 Shaft sleeve Pressure: p1 = 12 bar (175 PSI)
8 Drive collar Speed = 10 m/s (33 ft /s)
Permissible axial movement: ± 1.0 mm,
9 Set screw
d1  75 mm ± 1.5 mm

21
VTX Dual Seals For Eccentric Screw Pumps - Standard Cartridge Seals

Product Description Technical Features

1. Dual seal configuration 1. Ideal for use in process pump
2. Balanced design standardization
3. Independent of direction of rotation 2. O-ring is dynamically loaded to prevent
4. Cartridge construction shaft damage.
5. Double pressure balanced 3. Dimensional modification of the stuffing
6. Designed with integrated pumping box chamber is not required due to
device for increased efficiency in short radial installation height
circulation 4. Ideal to convert and retrofit pumps with
7. Suitable for eccentric screw pumps packings and large volume OEM
production
5. Cartridge unit factory assembled for
easy installation, which reduces down-
time
6. Rugged design for long operating life

VTX
CTX seals with modified cover for eccentric screw
pumps.
Example Pumps: Seepex BN, Netzsch NM...S,
NM...B, NE (P), Allweiler AE, AEB, AED, Robbins
& Myers / Moyno 2000 CC, and Mono E-Range.

Typical Industrial Applications

Foodstuffs and animal feed industries
Sweet cider pressing and beverage production
Viticulture and wineries
Spirit production and alcohol industry
6 4 1 2 10 9 12 15 16 17 Breweries and malt houses
Sugar industry
Pharmaceuticals and cosmetics industry
Oil and gas industry
Pulp and paper production
Paint and lacquer industry
Chemicals industry
7 5 8 3 11 13 14 19 18 Automobile industry
Water and wastewater industry
Materials
Seal face: Silicon carbide (Q1), Carbon
graphite resin impregnated (B), Tungsten
carbide (U2)
Seat: Silicon carbide (Q1)
Secondary seals: FKM (V), EPDM (E),
FFKM (K), Perflourocarbon rubber/PTFE (U1)
Springs: Hastelloy® C-4 (M)
Metal parts: CrNiMo steel (G), CrNiMo cast
steel (G)
Note: The item numbers as depicted above are based on our technical experience and Performance Capabilities
knowledge and are placed in the chronological order of their assembly procedure.
Sizes: Upto 140mm (Upto 5.500")
Other sizes on request
Temperature : t= - 40 °C...+220 °C
Item Description Item Description (-40 °F...+428 °F)
(Check O-ring resistance)
1 Seal face 9 Seal Face Sliding face material combination BQ1
2, 5, 7 O-ring 11 Spring Pressure: p1 = 25 bar (363 PSI)
10, 13,15 14 Speed = 16 m/s (52 ft/s)
Driver
Sliding face material combination Q1Q1 or
3 Spring 16 Set screw U2Q1
4,12 Seat 17 Retaining Ring Pressure: p1 = 12 bar (175 PSI)
Speed = 10 m/s (33 ft /s)
6 Shaft sleeve 18 Assembly Fixture Permissible axial movement: ± 1.0 mm,
8 Cover 19 HSH Cap Screw d1  75 mm ± 1.5 mm

22
 B750VN Single Seals API 682 Seals For Pumps - Standard Cartridge Seals

Product Description Technical Features

1. Single seal configuration 1. D e s i g n e d f o r " L o w - E m i s s i o n "
2. Balanced design conforming to the American STLE-
3. Independent of direction of rotation limits
4. Cartridge construction 2. Can handle extensive applications in
5. Category 2 and 3, Type A, Arrangement 1 various temperatures and pressures
6. Design in accordance to API 682 / ISO 3. Versatile in design to fit various seal
21049 chambers
7. Pumping device available for increased 4. Material of construction available in
efficiency in circulation (B750VP) special metallurgy
8. Rotary unit with multiple springs

6 7

11
F Q

11
10

1.1.2 6 1.1.7 1.1.4 1.1.1 1.2 7

d 2 H7

d 1 h6
d4

d5

d3

d6

1.1.6 1.1.5 1.1.3 2 5 1.3 4 9 13 12

Item Description
Item Description 2 Shaft sleeve
1.1.1 Seal face 4 Housing
1.1.2 Driver 5 Insert
1.1.3 Thrust ring 7 Throttle ring
1.1.4, 1.3, 6, 8 O-ring 9 Washer
1.1.5 Sleeve 10 Assembly fixture
1.1.6 Spring 11 Hexagon bolt
1.1.7 Set screw 12 Set ring
1.2 Seat 13 Set screw

23
 Typical Industrial Applications Materials
Light hydrocarbons Seal face: Carbon graphite antimony
Oil and gas industry impregnated (A)
Petrochemical industry Seat: Silicon carbide (Q1, Q2)
Refining technology Secondary seals: EPDM (E), NBR (P),
API 610 / ISO 13709 pumps FKM (V), FFKM (K)
Process pumps Springs: Hastelloy® C-4 (M)
Performance Capabilities Metal parts: CrNiMo steel (G), Duplex (G1),
Sizes: d = Upto 110 mm (Upto 4.250’’)* Hastelloy® C-4 (M)
Pressure: p1 = 40 bar (580 PSI)
Temperature: t = - 40 °C...+220 °C Design Variations
(-40 °F...+428 °F)
Speed = 23 m/s (75 ft /s) B750VP
Permissible axial movement: ± 2.0 ... 4.0 mm Dimensions, items and descriptions as B750VN,
depending on diameter and installation but with pumping ring. Shorter installation length
situation possible.
* Other sizes on request B750N
Dimensions, items and description as B750VN.
Standards Seal face: Silicon carbide (Q1, Q2)
API 682 / ISO 21049 Seat: Silicon carbide (Q1, Q2)

Dimensional Data
Dimensions in inch
API/d 1 API/d 2 API/d 3 API/d 4 d5 d6 l4 l5 l6 l7 l 11 Overall length

0.750 2.756 4.134 3.346 1.969 5.433 3.740 3.701 0.039 2.992 0.236 3.937
1.125 3.150 4.528 3.740 2.441 5.827 3.957 3.858 0.098 3.031 0.236 4.094
1.500 3.543 4.921 4.134 2.835 6.220 4.154 3.878 0.276 3.051 0.236 4.921
2.000 3.937 5.512 4.528 3.386 6.614 4.390 3.917 0.472 3.091 0.236 5.512
2.250 4.724 6.299 5.315 3.898 7.402 4.744 4.016 0.728 3.189 0.236 6.299
2.750 5.118 6.693 5.709 4.291 7.795 4.902 4.173 0.709 3.189 0.236 6.693
3.125 5.512 7.087 6.102 4.685 8.189 5.079 4.173 0.906 3.189 0.236 7.087
3.500 6.299 8.071 6.890 5.079 9.370 5.079 4.173 0.906 3.189 0.236 8.071
3.750 6.693 8.465 7.283 6.024 9.764 5.236 4.291 0.945 3.189 0.236 8.465
4.250 7.087 8.858 7.677 6.614 10.157 5.236 4.291 0.945 3.189 0.236 8.858

Dimensions in millimeter
API/d 1 API/d 2 API/d 3 API/d 4 d5 d6 l4 l5 l6 l7 l 11 Overall length

20 70 105 85 50 138 95.0 94.0 1.0 76.0 6 100

30 80 115 95 62 148 100.5 98.0 2.5 77.0 6 104
40 90 125 105 72 158 105.5 98.5 7.0 77.5 6 125
50 100 140 115 86 168 111.5 99.5 12.0 78.5 6 140
60 120 160 135 99 188 120.5 102.0 18.5 81.0 6 160
70 130 170 145 109 198 124.5 106.0 18.0 81.0 6 170
80 140 180 155 119 208 129.0 106.0 23.0 81.0 6 180
90 160 205 175 129 238 129.0 106.0 23.0 81.0 6 205
100 170 215 185 153 248 133.0 109.0 24.0 81.0 6 215
110 180 225 195 168 258 133.0 109.0 24.0 81.0 6 225
Note: Additional technical & dimensional information will be provided on request.

24
 B750VK Dual Seals API 682 Seals For Pumps - Standard Cartridge Seals

Product Description Technical Features

1. Dual seal configuration 1. Can handle extensive applications in
2. Balanced design various temperatures and pressures
3. Independent of direction of rotation 2. Versatile in design to fit various seal
4. Cartridge construction chambers
5. Bi-directional design available 3. Material of construction available in
6. Category 2 and 3, Type A, Arrangement special metallurgy
2 or 3 4. Special torque transmission design for
7. Design in accordance to API 682 / ISO high performance
21049 5. Operation reliability due to rugged
8. Pumping device available for increased metal torque transmission at the
efficiency in circulation rotating seal face
9. Rotary unit with multiple springs
10. Can accommodate reverse pressure

6 5

10 7

LBO
6

7
14
13

1.1.7 1.1.2 4 1.1.3 1.1.1 1.2 10 9 5 2.1.2 2.1.4 2.1.1 2.2 12 16 15

d 1 h6
d 2 H7

d3

d6
d5
d4

3 1.1.6 1.1.5 1.1.4 1.3 8 2.1.6 2.1.5 2.1.3 2.3 11

LBI

Item Description Item Description

1.1.1, 2.1.1 Seal face 6 Adapter
1.1.2, 2.1.2 Driver 7 O-ring
1.1.3, 2.1.3 Thrust ring 8 Washer
1.1.4, 2.1.4, 1.3, 2.3 O-ring 9 O-ring
1.1.5, 2.1.5 Spring Sleeve 10 Pin
1.1.6, 2.1.6 Spring 11 Housing
1.1.7 Set screw 12 HSH cap screw
1.2, 2.2 Seat 13 Assembly fixture
3 Shaft sleeve 14 Hexagon bolt
4 O-ring 15 Set ring
5 Key 16 Set screw

25
 Typical Industrial Applications Standards Design Variations
Light volatile and highly viscous hydrocarbons API 682 / ISO 21049 LBO

Oil and gas industry

Petrochemical industry Materials
Refining technology Seal face: Carbon graphite antimony
API 610 / ISO 13709 pumps impregnated (A), Silicon carbide (Q1, Q2)
Process pumps Seat: Silicon carbide (Q1, Q2)

d2 H7
d1 h6
d4

d3
d6
Secondary seals: EPDM (E), NBR (P),
FKM (V), FFKM (K)
Performance Capabilities
Springs: Hastelloy® C-4 (M)
Sizes: d1 = Upto 110 mm (Upto 4.250’’)* Metal parts: CrNiMo steel (G), Duplex (G1),
Pressure: p1 = 40 bar (580 PSI) Hastelloy® C-4 (M)
Temperature: t = - 40 °C...+220 °C LBI
(-40 °F...+428 °F) B750VK-D
Speed = 23 m/s (75 ft /s) Dual seal in back-to-back arrangement.
Permissible axial movement: ± 2.0 ... 4.0 mm Suitable for API 610 table 6 seal chambers.
depending on diameter and installation
situation
* Other sizes on request

Dimensional Data
Dimensions in inch

API/d1 API/d 2 API/d 3 API/d 4 d5 d6 l4 l5 l6 l7 l 10 Axial

movement
0.750 2.756 4.134 3.346 2.362 5.079 5.669 3.819 1.850 3.189 0.236 ±0.079
1.125 3.150 4.528 3.740 2.756 5.472 5.728 3.780 1.949 3.051 0.315 ±0.079
1.500 3.543 4.921 4.134 3.228 5.866 5.768 3.799 1.969 3.071 0.315 ±0.079
2.000 3.937 5.512 4.528 3.701 6.614 6.220 4.193 2.028 3.465 0.413 ±0.079
2.250 4.724 6.299 5.315 4.488 7.402 6.496 4.232 2.264 3.551 0.177 ±0.079
2.750 5.118 6.693 5.709 4.882 7.795 6.693 4.232 2.461 3.346 0.394 ±0.079
3.125 5.512 7.087 6.102 5.276 8.189 6.890 4.232 2.657 3.346 0.492 ±0.079
3.500 6.299 8.071 6.890 5.748 9.370 7.039 4.602 2.437 3.717 0.272 ±0.118
3.750 6.693 8.465 7.283 6.417 9.764 7.283 4.626 2.657 3.622 0.453 ±0.079
4.250 7.087 8.858 7.677 6.811 10.157 7.402 4.587 2.815 3.583 0.610 ±0.118

Dimensions in millimeter

API/d 1 API/d 2 API/d 3 API/d 4 d5 d6 l4 l5 l6 l7 l10 Axial

movement
20 70 105 85 60 129 144.0 97.0 47.0 81.0 6.0 ±2.0
30 80 115 95 70 139 145.5 96.0 49.5 77.5 8.0 ±2.0
40 90 125 105 82 149 146.5 96.5 50.0 78.0 8.0 ±2.0
50 100 140 115 94 168 158.0 106.5 51.5 88.0 10.5 ±2.0
60 120 160 135 114 188 165.0 107.5 57.5 90.2 4.5 ±2.0
70 130 170 145 124 198 170.0 107.5 62.5 85.0 10.0 ±2.0
80 140 180 155 134 208 175.0 107.5 67.5 85.0 12.5 ±2.0
90 160 205 175 146 238 178.8 116.9 61.9 94.4 6.9 ±3.0
100 170 215 185 163 248 185.0 117.5 67.5 92.0 11.5 ±2.0
110 180 225 195 173 258 188.0 116.5 71.5 91.0 15.5 ±3.0
Note: Additional technical & dimensional information will be provided on request.

26
 SPX Single Seals Split Seals

Product Description Technical Features

1. Single seal in split configuration 1. Economical to assemble as the complete
2. Balanced design dismantling of the equipment is not
necessary to install the seal
3. Independent of direction of rotation 2. Reduces down time due to ease in installation
4. For plain shafts 3. Rugged seal construction
5. Semi-cartridge construction 4. Distortion of the seat is avoided by mechanical
6. Built-in flushing connections decoupling of the clamping ring
7. Designed with external pressurization 5. Ease in installation and no modifications are
required because the seal is located outside
8. Factory assembled fully split single of the stuffing box.
seal, 2 x 2 segments 6. Due to the stationary design and the elastic
9. Stationary design with multiple springs seat mounting a high tolerance of shaft
deflections can be accommodated
7. Low leakage is achieved by the elimination of
secondary seals which eliminates leakage
paths between split components
8. Shaft is protected by uniform torque
transmission through the clamping ring which
prevents damage caused by set screws.
9. Springs are product protected to avoid
contamination and clogging

l4 Typical Industrial Applications

Agitators
Chemical Industry
Centrifugal pumps
M12

Conveying pulp with stock pumps

Cooling water pumps for energy generation
Conveying timber to refiners with pumping
screws
l5
9 Circulation of pulp-and-water mixtures in storage
7 16 5 4 2 3 11
Dw h8

vessels
Displacement pumps
d2

d1

Process industry
12 6 15 1 8 Petrochemical Industry
Power Plant Technology
Pulp and paper industry
Pump stations for waste water treatment
Performance Capabilities
10
Shaft diameter: d1= Upto...150mm (Upto... 6.000’’)
14 Pressure: p1 = 10 bar (145 PSI)
13 Temperature: t = –40 °C... +150 °C
17 (–40 °F... + 300 °F),
x
above 80 °C (175 °F) flush is recommended
l3 Speed = 10 m/s (33 ft/s)
Axial movement: ± 1.5 mm (1/16")
l2 Radial movement: ± 0.8 mm (1/32")
l1
Note: The item numbers as depicted above are based on our technical experience and Materials
knowledge and are placed in the chronological order of their assembly procedure.
Seal face: Carbon graphite antimony
impregnated (A), Silicon carbide (Q2)
Item Description Seat: Silicon carbide (Q2)
1 Seal face Secondary seals: FKM (V), EPDM (E), NBR(P)
Springs: CrNiMo steel (G)
2, 5, 7 O-ring Metal parts: CrNiMo steel (G)
3 Spring Installation, Details, Option
4 Seat
0

6 Driver 35

8 Thrust ring
da

9 Clamp collar
10 Housing
11 Assembly fixture
s

12, 15 Gasket
13 Head screw plug
14 Mounting plate
16 Set screw
20 0 s
17 Socket head screw a
27
 Dimensions
Dimensions in inch

dw d1 d2 da a s l1 l2 l3 l4 l5 X
2.000 2.953 3.307 5.433 3.456 0.591 2.480 2.402 1.181 1.772 0.118 3/8 NPT
2.125 3.110 3.465 5.787 3.622 0.591 2.480 2.402 1.142 1.772 0.118 3/8 NPT
2.375 3.504 3.976 5.866 4.134 0.689 2.520 2.441 1.181 1.811 0.118 3/8 NPT
2.500 3.642 4.114 6.181 4.272 0.689 2.520 2.441 1.181 1.811 0.118 3/8 NPT
2.750 3.858 4.449 6.929 4.646 0.787 2.520 2.441 1.181 1.811 0.118 3/8 NPT
3.000 4.094 4.803 7.638 5.000 0.787 2.559 2.480 1.339 1.850 0.118 3/8 NPT
3.250 4.331 5.197 7.520 5.315 0.787 2.559 2.480 1.220 1.850 0.118 3/8 NPT
3.500 4.764 5.512 7.992 5.709 0.866 2.854 2.776 1.240 1.988 0.118 1/2 NPT
3.750 4.921 5.630 8.110 5.827 0.866 2.854 2.776 1.240 1.988 0.118 1/2 NPT
4.000 5.157 5.906 8.504 6.102 0.866 2.854 2.776 1.240 1.988 0.118 1/2 NPT
4.250 5.591 6.496 9.055 6.693 0.866 2.854 2.776 1.240 1.988 0.118 1/2 NPT
4.500 5.984 6.890 9.449 7.087 0.866 2.854 2.776 1.240 1.988 0.118 1/2 NPT
4.750 5.984 6.890 9.449 7.087 0.866 2.854 2.776 1.240 1.988 0.118 1/2 NPT
5.000 6.378 7.283 10.551 7.480 1.024 3.524 3.445 1.713 2.461 0.157 1/2 NPT
5.500 6.890 7.874 11.929 8.071 1.024 3.524 3.445 1.713 2.461 0.157 1/2 NPT
6.000 7.402 8.465 12.126 8.661 1.024 3.524 3.445 1.713 2.461 0.157 1/2 NPT

Dimensions in millimeter
dw d1 d2 da a s l1 l2 l3 l4 l5 X
50 75 84 138 88 15 63 61 30 45 3 3/8 NPT
60 89 101 149 105 17,5 64 62 30 46 3 3/8 NPT
70 98 113 176 118 20 64 62 30 46 3 3/8 NPT
80 110 132 191 135 20 65 63 31 47 3 3/8 NPT
90 121 140 203 145 22 72.5 70.5 31.5 50.5 3 1/2 NPT
100 131 150 216 155 22 72.5 70.5 31.5 50.5 3 1/2 NPT
110 142 165 230 170 22 72.5 70.5 31.5 50.5 3 1/2 NPT
120 152 175 240 180 22 72.5 70.5 32.5 50.5 3 1/2 NPT
125 162 185 268 190 26 89.5 87.5 43.5 62.5 4 1/2 NPT
140 175 200 303 205 26 89.5 87.5 43.5 62 4 1/2 NPT
150 188 215 308 220 26 89.5 87.5 43.5 62.5 4 1/2 NPT
Note: Additional technical & dimensional information will be provided on request.

28
 BGH201 Single Seals Split Seals

Product Description Technical Features

1. Single seal in semi split configuration 1. Economical to assemble as the
2. Balanced design complete dismantling of the equipment
3. Independent of direction of rotation is not necessary to install the seal
4. For plain shafts 2. Reduces down time due to ease in
5. Rotary unit with multiple springs installation
3. Rugged seal construction
4. Versatile split seat can be used on both
the sides
5. Springs are product protected to avoid
contamination

l3 l4 -0.1 Typical Industrial Applications

Chest agitators
2 Cooling water pumps
f o Defibrators
15
Gears
15 o Power plant technology
Pulp and paper industry
Sea water desalination
mx Shipbuilding
Stern tubes
Water and waste water technology
Water turbines

Performance Capabilities
1.6 1.3 1.5 1.7 1.1 2 3 Sizes: d1 = Upto 310 mm (Upto 12.250’’)
h8

d4 +0.1
d5 H7
d3

d2

Pressure: p1 = 25 bar (363 PSI)

d1

1.2 1.4
l8 Temperature: t1 = 150 °C (302 °F)
Speed = 20 m/s (66 ft/s)
Permissible axial movement: ± 2.0 mm
Materials
Seal face: Silicon carbide (Q1)
Seat: Silicon carbide (Q1, Q2), Carbon graphite
R

antimony impregnated (A), Carbon graphite resin

impregnated (B)
Secondary seals: FKM (V), EPDM (E), NBR (P)
l1 Metal parts: CrNiMo steel (G)
Torque Transmissions
Note: The item numbers as depicted above are based on our technical experience and
knowledge and are placed in the chronological order of their assembly procedure.

Item Description
d1 > 105 mm
1.1 Seal face1) Set screws with cone
1.2 Driver collar points 4 x offset by 90°
1.3 O-ring1)
1.4 O-ring1)
1.5 Spring
1.6 Set screw
1.7 O-ring1)
2 Stationary seat1)
3 O-ring1)
1)
For disassembly of unsplit seal faces, seats
and O-ring should be broken or cut.

29
 Design Variations
l11
l33

O
3 x 120
offset
BGH211
Dimensions, items and descriptions as BGH201.
Ø4

4 1.2 Item 1.2 driver collar is modified for securing on

d11 h8
d6

22 stepped shafts.
Unsplit as original equipment: Designation
BGH210.

Dimensional Data
Dimensions in millimeter
d1 d11 d2 d3 d4 d5 d6 l1 l 11 l3 l 33 l4 l8 R f mx

50 40 60 95 80.5 89.6 55 95.3 75.3 70 50 18.8 31.8 2.5 6 M8

55 45 65 100 85.5 94.6 60 95.3 75.3 70 50 18.8 31.8 2.5 6 M8
60 50 70 105 90.5 99.6 65 95.3 75.3 70 50 18.8 31.8 2.5 6 M8
65 55 75 110 95.5 104.6 70 95.3 75.3 70 50 18.8 31.8 2.5 6 M8
70 60 80 115 100.5 109.6 75 95.3 75.3 70 50 18.8 31.8 2.5 6 M8
75 65 85 120 105.5 114.6 80 95.3 75.3 70 50 18.8 31.8 2.5 6 M8
80 70 90 125 110.5 119.6 85 95.3 75.3 70 50 18.8 31.8 2.5 6 M8
85 75 95 130 115.5 124.6 90 95.3 75.3 70 50 18.8 31.8 2.5 6 M8
90 80 100 135 120.5 129.6 95 95.3 75.3 70 50 18.8 31.8 2.5 6 M8
95 85 105 140 125.5 134.6 100 95.3 75.3 70 50 18.8 31.8 2.5 6 M8
100 90 110 145 130.5 139.6 105 95.3 75.3 70 50 18.8 31.8 2.5 6 M8
105 95 115 150 135.5 144.6 110 95.3 75.3 70 50 18.8 31.8 2.5 6 M8
110 100 120 155 140.5 149.6 115 95.3 75.3 70 50 18.8 31.8 2.5 6 M8
115 105 125 160 145.5 154.6 120 95.3 75.3 70 50 18.8 31.8 2.5 6 M8
120 110 130 165 150.5 159.6 125 95.3 75.3 70 50 18.8 31.8 2.5 6 M8
125 115 135 170 155.5 164.6 130 95.3 75.3 70 50 18.8 31.8 2.5 6 M8
130 120 140 175 160.5 169.6 135 95.3 75.3 70 50 18.8 31.8 2.5 6 M8
135 125 145 180 165.5 174.6 140 95.3 75.3 70 50 18.8 31.8 2.5 6 M8
140 130 150 185 170.5 179.6 145 95.3 75.3 70 50 18.8 31.8 2.5 6 M8
145 135 155 190 175.5 184.6 150 95.3 75.3 70 50 18.8 31.8 2.5 6 M8
150 140 160 195 180.5 189.6 155 95.3 75.3 70 50 18.8 31.8 2.5 6 M8
155 145 165 200 185.5 194.6 160 95.3 75.3 70 50 18.8 31.8 2.5 6 M8
160 150 170 205 190.5 199.6 165 95.3 75.3 70 50 18.8 31.8 2.5 6 M8
165 155 175 210 195.5 204.6 170 95.3 75.3 70 50 18.8 31.8 2.5 6 M8
170 160 180 215 200.5 209.6 175 95.3 75.3 70 50 18.8 31.8 2.5 6 M8
175 165 185 220 205.5 214.6 180 95.3 75.3 70 50 18.8 31.8 2.5 6 M8
180 170 192 225 212.5 224.6 185 104.2 84.2 72 52 26.4 38.0 3.5 6 M8
185 175 197 230 217.5 229.6 190 104.2 84.2 72 52 26.4 38.0 3.5 6 M8
190 180 202 235 222.5 234.6 195 104.2 84.2 72 52 26.4 38.0 3.5 6 M8
195 185 207 240 227.5 239.6 200 104.2 84.2 72 52 26.4 38.0 3.5 6 M8
200 190 212 245 232.5 244.6 205 109.2 84.2 77 52 26.4 38.0 3.5 6 M10
205 195 217 255 237.5 249.6 210 109.2 84.2 77 52 26.4 38.0 3.5 8 M10
210 200 222 260 242.5 254.6 215 109.2 84.2 77 52 26.4 38.0 3.5 8 M10
220 210 232 270 252.5 264.6 225 109.2 84.2 77 52 26.4 38.0 3.5 8 M10
230 220 242 280 262.5 274.6 235 109.2 84.2 77 52 26.4 38.0 3.5 8 M10
240 230 252 290 272.5 284.6 245 109.2 84.2 77 52 26.4 38.0 3.5 8 M10
250 240 262 300 282.5 294.6 255 109.2 84.2 77 52 26.4 38.0 3.5 8 M10
260 250 272 310 295.5 307.6 265 109.2 84.2 77 52 26.4 38.0 3.5 8 M10
270 260 282 320 305.5 317.6 275 109.2 84.2 77 52 26.4 38.0 3.5 8 M10
280 270 292 330 315.5 327.6 285 109.2 84.2 77 52 26.4 38.0 3.5 8 M10
290 280 302 340 325.5 337.6 295 109.2 84.2 77 52 26.4 38.0 3.5 8 M10
300 290 312 350 335.5 347.6 305 109.2 84.2 77 52 26.4 38.0 3.5 8 M10
310 300 322 360 345.5 357.5 315 109.2 84.2 77 52 26.4 38.0 3.5 8 M10
d1 > 310 on request
inch size available from size 2.000 to 12.250
Note: Additional technical & dimensional information will be provided on request.

30
 ADKS Carbon Floating Ring Seals - Shaft Seals

Product Description Technical Features

1. Designed to accommodate axial shaft 1. Ease of installation during assembly
movement due to split design (dismantling of shaft
2. Capable of running dry is not necessary)
3. Radially cut multi-part seal rings 2. Operational durability
4. Shaft free of sealing components which 3. Easy to maintain
minimizes the shaft vibrations 4. Trouble free replacement due to
5. Seal rings are self adjusting segmented seal ring design
6. Shaft movement is accommodated by
seal rings
7. Minimal power consumption as seal
rings are non-contacting
8. Design of the seal housing is split
9. Low leakage due to extremely reduced
gap during operation

L Typical Industrial Applications

Bearing seals (gear box, motors)
Chemical industry
Food processing industry
Fumes and exhaust,solids containing,
flammable (ATEX), acid containing and toxic
d B1

gases (Solids containing) steams / liquid mist

Gases
Medium-sized and large fans / blowers
Metal production and processing
Mixers, agitators, mills, dryer
Oil mist / penetrating oil
Petrochemical industry
Power plant technology
Steam turbines
Waste incineration and removal industry
1 3 4 2 Water
d h6

Lk 1
D3
d1

Standards
5
FDA

Materials
Seal ring: Carbon, PTFE compound
Housing: 1.4021, 1.4571, Hastelloy®, Titanium,
Inconel®, others
Tension spring / detent: 1.4571, Hastelloy®,
Titanium, Inconel®

Performance Capabilities
Shaft diameter:
d = 40 ... 340 mm (1.57" … 13.39")
Operating pressure: p = vacuum ... 20 bar
(290 PSI) abs.
Note: The item numbers as depicted above are based on our technical experience and Operating temperature: t = –120 °C ... +800 °C
knowledge and are placed in the chronological order of their assembly procedure.
(–184 °F … +1,472 °F) for carbon,
max. 225 °C (437 °F) for PTFE compound
Speed = max. 150 m/s (492 ft/s)
for carbon, max. 40 m/s (131 ft/s) for PTFE
Item Description compound
1 Flat seal Radial play: ±1.0 … 5.0 mm (±0.04" … 0.2")
Axial movement: theoretically unlimited
2 Housing, 2-piece Recommended wear guard: >300 HB (low
3 Seal ring pressure), >58 HRC (high pressure)
4 Tension spring
5 Detent

31
 Installation, Details, Options

ADKS 200 (split design) Seal rings ADKS 200 (3-part, radial cut),
Carbon / PTFE compound

Product Variants

L L L
8 30
dB1

d B1

1 3 4 2 1 3 4 2
d h6
LK 1

Lk 1
d h6

D3
d1
D3
d1

5 5 1 3 4 2

d h6
LK

d1
D1
D2
D

dB

ADKF ADKS 200 ADS

With short design, reduced housing For toxic and solids containing gases as With barrier gas and grease barrier port (for e.g.
outside diameter and grease barrier well as ATEX applications type shaft seal toxic and solids containing gases as well as
port (for clean media, not for solids with short design, reduced housing outside ATEX applications, on special request).
containing gases). diameter and barrier gas port (for e.g. toxic
and solids containing gases).

32
 PP-S Single Seals Mechanical Seals For Pumps - Engineered Seals

Product Description Technical Features

1. Single seal configuration 1. O-rings are dynamically loaded to
2. Balanced design prevent shaft damage
3. Independent of direction of rotation 2. Easy and trouble-free installation
4. Semi-Cartridge construction 3. Due to large radial clearance the
5. No dynamic O-ring on the shaft damage to the seal faces are avoided,
in addition to the seal faces being
protected by strong steel parts
4. Misalignment during installation and
operations is reduced due to the static
springs

Typical Industrial Applications

Pulp and paper industry
Chemical industry
All clean none abrasive media
Performance Capabilities
Temperature: t = -20 °C ... +140 °C
(-4 °F ... +284 °F)
Pressure: p1 ... 25 bar (363 PSI)
Sliding velocity: vg ... 20 m/s (66 ft/s)

Materials
37
Seal face: Silicon carbide (Q12), Carbon (A)
Secondary seals: FKM (V), EPDM (E),
FFKM (K)
Metal parts: CrNiMo steel (G),
12 13 18 2 Grade 5A (4T), SMO 654 (4U)
Suitable for following equipments
Ahlstar UP A MS21 range of pumps
22 2 5 1 3 23 16 24 Sulzer A, APP/APT pumps
Sulzer SL mixers
Metso conical refiners
Stock pumps

Item Description
1, 5 Seal face
2, 12, 22, O-ring
23, 24
3 Spring
13 Sleeve
16 Housing
18 Pin
37 Assembly fixture

33
PP-D Dual Seals Mechanical Seals For Pumps - Engineered Seals

Product Description Technical Features

1. Dual seal configuration 1. Seals can be operated with pressurized
2. Balanced design buffer fluid or with quench
3. Independent of direction of rotation 2. O-rings are dynamically loaded to
4. Semi-Cartridge construction prevent shaft damage
5. Double pressure balanced design 3. Easy and trouble-free installation
6. Designed with provision for internal 4. Due to large radial clearance, the
barrier fluid circulation damage to the seal faces are avoided,
7. No dynamic O-ring on the shaft in addition to the seal faces being
8. Robust construction with shrink-fitted protected by strong steel parts
seal faces 5. Misalignment during installation and
9. Seal faces have a large clearance to operations is reduced due to the static
the shaft springs on both the faces
10. Static springs on both the sides 6. Dual seal can also be used as a single
seal by removing the atmospheric seal
parts

Typical Industrial Applications

Pulp and paper industry
Chemical industry
37 Clean, abrasive or corrosive liquids
Stocks of various kind
Applications where crystallization is a problem
Performance Capabilities
Temperature: t = -20 °C ... +140 °C
(- 4 °F ... + 284 °F)
(180 °C (356 °F) with FFKM elastomers)
Pressure: p1 ... 25 bar (363 PSI), p3
12 13 18 2 15 3 15 41 Speed = 20 m/s (66 ft/s)

Non-flow operation:
22 2 5 1 3 23 16 24 18 1 5 25 20 Temperature: t = +5 °C ... +100 °C
(+ 41 °F ... +212 °F)
Pressure: p1 max. 10 bar (145 PSI), p3 > p1
Sliding velocity: vg ... 20m/s (66 ft/s)

Materials
Seal face: Silicon carbide (Q12), Carbon (A)
Secondary seals: FKM (V), EPDM (E),
43 FFKM (K)
Metal parts: CrNiMo steel (G),
Grade 5A (4T), SMO 654 (4U)

Suitable for following equipments

Ahlstar UP A MS21 range of pumps
Sulzer A, APP/APT pumps
Item Description Sulzer SL mixers
Metso conical refiners
1 Seal face
Stock pumps
5 Seat
13 Sleeve
16 Housing
18 Pin
37 Assembly fixture
2, 12, 15, O-ring
22, 23, 24, 25
43 Plug

34
 BR Single & Dual Seals Mechanical Seals For Pumps - Engineered Seals

Product Description Technical Features

1. Single and Dual seal configuration 1. Accommodates shaft deflections due to
2. Balanced design stationary design
3. Independent of direction of rotation 2. Designed to handle media containing
4. Cartridge construction solids
5. Stationary design with multiple springs 3. O-ring is dynamically loaded to prevent
6. Seat arrangement is designed behind shaft damage.
the impeller 4. Can operate under vacuum without
7. Seat design is rotary locking the seat
8. Specially designed sleeve to protect the 5. Pumping device available for increased
springs from contamination efficiency in circulation
9. Variable designs available with guide 6. Springs are product protected to avoid
sleeve for applications with or without contamination
quench

Typical Industrial Applications

3 1
BR100 Water and waste water technology
4 +0.1 t1 Dirty, abrasive and solids containing media
Dredger pumps
Mining industry
d8

Oil and gas industry

Oil sand extraction plants
Power plant technology
Pulp and paper industry
Sewage water pumps
Scrubbers in FGD plants
5 1.1 1.2 Performance Capabilities
Sizes: dN = Upto 270 mm (Upto 10.625’’)
d10 h 8

Pressure: p1*) = 16 bar (230 PSI)

d 9 H8

d4 H8
0.1

d 1h

d11
d1
d3
_

Temperature: t = - 20 °C ...+160 °C
d2

(-4 °F ...+320 °F)

Speed = 10 m/s (33 ft/s)
6 7 2 3 4 8 *) For operation under vacuum it is necessary
to arrange for quenching on the atmosphere
side.

Standards
EN 12756
Materials
Seal face: Silicon carbide (Q1, Q2)
5 2
Seat: Silicon carbide (Q1, Q2)
BR110
Notes
Note: The item numbers as depicted above are based on our technical experience and Direction of installation:
knowledge and are placed in the chronological order of their assembly procedure.
From the impeller side: BR100
From the bearing side: BR110
Item Part no. Description
Stationary Seats
1.1 472 Seal face
l 7 +0.5 l9 l6
1.2 520 Sleeve
l5
2 412.1 O-ring
20 O

R1
3 474 Thrust ring
4 477 Spring
5 475 Seat (G11)
6 412.2 O-ring
d8

H11

H8
H11
H8

7 412.3 O-ring
d6

d7
d7

d6
k2

8 441 Housing
d5

t
DIN 24250
G2 G9
Direction of installation:- from the impeller
side BR100 from the bearing side BR110 (dN 36 ... 90 mm) (dN 95 ... 180 mm)
35
 Design Variations
l10
l12 l13
l15 l16

2 1
d1h

1.2
dN

1.1 2
d1

1 5

d1h
1.1

d3
d1
5 8

dN
d1

d12 H11
d1h max

d13 H8
d11

dN
6 7 3 4

d1
6 7 2 3 4

d 14
l11 5

BR200 BR300 BRKS-D BRZ100

Cartridge-type single seal with guide Cartridge-type single seal. Insert (Item Double seal in cartridge design for Single seal with cylindrical spring and
sleeve (Item no. 2) for use with quench. no. 1) either metal or silicon carbide. operation in barrier or buffer pressure type G76 seat. For installation in covers
Insert (Item no. 1) either metal or silicon Optional without maintenance rinsing. (does not open if barrier pressure fails), with installation dimensions according
carbide. available alternatively with a pumping to EN 12756 B or U. Installation length l11
screw for a higher rate of circulation. corresponds to max. l1k. Intermediate
Torque transmission e.g. by shrink disk. sizes on request.

Dimensional Data
Dimensions in millimeter
d1 d 1h d N d2 d3 d4 d5 d6 d7 d8 d9 d 10 d 11 l l1 l2 l3 l4 l5 l6 l7 l9 k2 t t1
+0.2min
20 28 36 47.1 65 70 46 56 63 4 40 38 75 75 53 20 19.5 17 10.5 6 9 8 51 4.5 3
25 33 41 52.1 70 75 51 62 70 4 45 43 80 75 53 20 19.5 17 10.5 6 9 9.5 56.5 4.5 3
28 38 46 57.1 75 80 56 67 75 4 50 48 85 75 53 20 19.5 17 10.5 6 9 9.5 61.5 4.5 3
33 43 51 62.1 80 85 61 72 80 4 55 53 90 75 53 20 19.5 17 10.5 6 9 10.5 66.5 4.5 3
38 48 56 67.1 85 90 66 77 85 4 60 58 95 75 53 20 19.5 17 10.5 6 9 10.5 71.5 4.5 3
43 53 61 72.1 90 95 69 81 90 4 65 63 100 75 53 20 19.5 17 10.5 7 9 11 75 4.5 3
48 58 66 77.1 95 100 76 88 97 4 70 68 105 75 53 20 19.5 17 10.5 7 9 11.5 82 4.5 3
53 63 71 82.1 101 105 81 95 105 4 75 73 110 75 53 20 19.5 17 10.5 7 9 11.5 88 4.5 3
55 65 75 87.1 106 110 86 100 110 4 79 78 115 75 53 20 19.5 17 10.5 7 9 11.5 93 4.5 3
60 70 80 92.1 111 115 91 105 115 4 84 83 120 75 53 20 19.5 17 10.5 7 9 13 98 4.5 3
65 75 85 97.1 116 120 96 110 120 4 89 88 125 75 53 20 19.5 17 10.5 7 9 13 103 4.5 3
70 80 90 102.1 121 125 101 115 125 4 94 93 130 75 53 20 19.5 17 10.5 7 9 13 108 4.5 3
75 85 95 107.1 126 130 107 122.2 134.3 5 99 98 135 75 53 20 19.5 17 10.5 10 12 20 114.5 7 3
80 90 100 112.1 131 135 107 122.2 134.3 5 104 103 140 75 53 20 19.5 17 10.5 10 12 20 114.5 7 3
90 100 110 126.1 147 155 117 136.2 148.3 5 116 117 163 98 73 30 22 19 16.0 10 12 20 126.5 7 4
100 110 120 136.1 157 165 132 146.2 158.3 5 126 127 173 98 73 30 22 19 16.0 10 12 20 139 7 4
110 120 130 145.1 167 175 142 156.2 168.3 5 136 136 183 98 73 30 22 19 16.0 10 12 20 149 7 4
120 130 140 154.1 177 185 152 168.2 180.3 5 146 145 193 98 73 30 22 19 16.0 10 12 22 160 7 4
130 140 150 163.9 188 195 162 178.2 190.3 5 156 155 203 98 73 30 22 19 16.0 12 12 24 170 7 4
140 150 160 174.9 189 205 172 188.2 200.3 5 166 166 213 98 73 30 22 19 16.0 12 12 24 180 7 4
160 170 180 193.9 220 230 187 212.5 224.3 5 186 185 238 98 73 30 22 19 16.0 12 12 28 199.5 7 4
180 190 200 213.9 240 255 - - - - 206 205 265 98 73 30 22 19 16.0 - - - - - 4
190 200 210 231.9 255 270 - - - - 218 220 280 115 83 40 28.35 24.7 19.0 - - - - - 5
200 210 220 241.9 265 280 - - - - 228 230 290 115 83 40 28.35 24.7 19.0 - - - - - 5
210 220 230 251.9 275 290 - - - - 238 240 300 115 83 40 28.35 24.7 19.0 - - - - - 5
220 230 240 261.9 285 300 - - - - 248 250 310 115 83 40 28.35 24.7 19.0 - - - - - 5
230 240 250 271.9 295 310 - - - - 258 260 320 115 83 40 28.35 24.7 19.0 - - - - - 5
250 260 270 291.9 315 330 - - - - 278 280 340 115 83 40 28.35 24.7 19.0 - - - - - 5

BRZ100 Dimensional Data

Dimensions in millimeter
dN d 1h d1 d11 d12 d13 d14 l 10 l 11 l 12 l 13 l 15 l 16

35 33 20 56 42 48 3 57.7 49.2 15 42.7 2 5

43 39 27 67 54 61 4 57.7 49.2 15 42.7 2 6
54 50 35 78 65 73 4 59.8 52.1 15.5 44.3 2.5 6
66 60 47 91 77 85 4 66 58 16.5 49.5 2.5 6
77 72 55 103 88 97 4 74.5 66 17.5 57 2.5 7
100 90 70 125 110 120 4 82 73 21 61 3 7
Dimensions for shaft diameters from 250 mm on request.
inch size available from size 0.750 to 10.625
Note: Additional technical & dimensional information will be provided on request.

36
 SBPV/SBFV Single Seals Mechanical Seals For Pumps - Engineered Seals

Product Description Technical Features

1. Single seal configuration 1. Accommodates shaft deflections due to
2. Balanced design stationary design
3. Independent of direction of rotation 2. Can be designed for individual pump
4. Cartridge construction application with corresponding
5. Stationary design with multiple springs connection parts to be adopted to the
6. Designed with integrated pumping pump seal chamber
device for increased efficiency in 3. Optimum heat dissipation due to
circulation integrated pumping device available for
7. Robust construction with shrink-fitted increased efficiency in circulation and
seal face optimized seat design
8. Heavy duty design of solid stationary 4. Cartridge unit factory assembled for
seat easy installation, which reduces down-
time
5. Trouble-free long-term operation due to
heavy duty single seat design with
bandage
6. Can operate under high sliding
velocities and high pressures

Typical Industrial Applications

Amines Injection pumps
Caustic soda Multi-phase pumps
Chemical industry Oil and gas industry
Crude oil Process water
Crystallizing media Refining technology
Crude oil feed pumps Sour water
Hot water

Standards
API 682 / ISO 21049

Performance Capabilities
Sizes: d1* = Upto 250 mm (Upto 10.000’’)
Pressure: p1 = 150 bar (2,175 PSI)
Temperature: t = 300 °C (572 °F)
Speed = 60 m/s (197 ft/s)
Permissible axial movement: ± 3 mm
* Other sizes on request
9 6 2 1.1.1 1.2
Materials
Seal face: SiC-C-Si Silicon impregnated
carbon (Q3), Carbon graphite antimony
1.1.4 1.1.3 impregnated (A)
Seat: Silicon carbide (Q)
Secondary seals: FKM (V), EPDM (E),
FFKM (K)
Springs: Hastelloy® C-4 (M)
Metal parts: CrNiMo steel (G), Duplex (G1),
Super Duplex (G4), Titanium (T2),
Hastelloy® C-4 (M)
Design Variations
SBFV
Same design as SBPV but with pumping screw

Item Description
1.1.1 Seal face pressure-stabilized
1.1.3 Spring
1.1.4 Back-up ring
1.2 Seat
2 Seat housing with pumping
screw (F) or pumping ring (P)
6 Cover
9 Assembly fixture

37
SBF(V)-D / SBP(V)-D Dual Seals Mechanical Seals For Pumps - Engineered Seals

Product Description Technical Features

1. Dual seal configuration 1. Accommodates shaft deflections due to
2. Balanced design stationary design
2. Can be designed for individual pump
3. Independent of direction of rotation application with corresponding connection
4. Cartridge construction parts to be adopted to the pump seal
5. Stationary design with multiple springs chamber
6. Designed with integrated pumping 3. Optimum heat dissipation due to integrated
device for increased efficiency in pumping device available for increased
circulation efficiency in circulation and optimized seat
design
7. Robust construction with shrink-fitted 4. Cartridge unit factory assembled for easy
seal face installation, which reduces down-time
8. Heavy duty design of solid stationary 5. Trouble-free long-term operation due to
seat heavy duty single seat design with bandage
6. Can operate under high sliding velocities
and high pressures
7. Can be adopted for use in compliance with
API 682, type ES
8. Versatile application for various kinds of
heavy duty applications

Typical Industrial Applications

Chemical industry
Crude oil
Crude oil feed pumps
Injection pumps
Multi-phase pumps
Oil and gas industry
Process water
Refining technology
Volatile and non-volatile hydrocarbons

Standards
API 682 / ISO 21049

Performance Capabilities
14 12 8 2 10 1.2 1.1.1 6 Sizes: d1* = Upto 250 mm (Upto 10.000’’)
Pressure: p1 = 150 bar (2,175 PSI)
Temperature: t = 200 °C (392 °F)
1.1.3 4 Speed = 60 m/s (197 ft/s)
* Other sizes on request
Materials
Seal face: SiC-C-Si, Silicon impregnated
carbon (Q3), Carbon graphite antimony
impregnated (A)
Seat: Silicon carbide (Q)
Secondary seals: FKM (V), EPDM (E),
FFKM (K)
Springs: Hastelloy® C-4 (M)
Metal parts: CrNiMo steel (G), Duplex (G1),
Super Duplex (G4), Pure Titanium (T2),
Hastelloy® C-4 (M)
Design Variations
SBF(V)1-D / SBP(V)1-D
Item Description Same design as SBF(V)-D / SBP(V)-D but with
1.1.1 Seal face loosely inserted seal face for extreme
applications.
1.1.3 Spring
Pressure: p1 = 200 bar (2900 PSI)
1.2 Seat
2 Shaft sleeve
4 Clamping sleeve
6 Housing
8 Cover
10 Pumping sleeve
12 Assembly fixture
14 Shrink disk

38
 SBF/SBP Single Seals Mechanical Seals For Pumps - Engineered Seals

Product Description Technical Features

1. Single seal configuration 1. Accommodates shaft deflections due to
2. Balanced design stationary design
3. Independent of direction of rotation 2. Can be designed for individual pump
4. Cartridge construction application with corresponding
5. Stationary design with multiple springs connection parts to be adapted to the
6. Designed with integrated pumping pump seal chamber
device for increased efficiency in 3. Optimum heat dissipation due to
circulation integrated pumping device available for
7. Robust construction with shrink-fitted increased efficiency in circulation and
seal face optimized seat design
8. Heavy duty design of solid stationary 4. Cartridge unit factory assembled for
seat easy installation, which reduces down-
time
5. Trouble-free long-term operation due to
heavy duty single seat design with
bandage
6. Can operate under high sliding
velocities and medium pressures

Typical Industrial Applications

Boiler feed water pumps
Power plant technology
Performance Capabilities
Sizes: d1* = Upto 250 mm (Upto 10.000’’)
Pressure: p1 = 50 bar (725 PSI)
Temperature: t = 300 °C (572 °F)
Speed = 60 m/s (197 ft/s)
Permissible axial movement: ±3 mm
* Other sizes on request
Materials
Seal face: Silicon carbide (Q), Carbon
graphite antimony impregnated (A), Carbon
graphite resin impregnated (B)
Seat: Silicon carbide
Secondary seals: EPDM (E), FFKM (K)
Springs: CrNiMo steel (G)
14 9 1.1.1 1.2 Metal parts: CrNiMo steel (G)
Design Variations

SBF4
Single Mechanical Seal with integrated jacket
6 1.1.3 8 2 cooling, for boiler feed pumps

Item Description
1.1.1 Seal face
1.1.3 Spring
1.2 Seat
2 Shaft sleeve
6 Cover
8 Pumping screw with flow guide
9 Assembly fixture
14 Shrink disk

39
B100 / B800 Single Seals Standard Mechanical Seals - Pusher Seals

Product Description Technical Features

1. Single seal configuration 1. Compact design
2. Balanced design 2. Capable of withstanding high pressure
3. Independent of direction of rotation 3. O-ring is dynamically loaded to prevent
4. Stationary design with multiple springs shaft damage.
4. Spring loaded stationary design
accommodates shaft misalignments
5. Can handle media with solid content
6. Easy to assemble due to short axial
installation length

3 Typical Industrial Applications

All seal chambers with a very short axial
Ø3

installation length
Bearing seal
Lube oils
Process industry
Item Part no. Description Roller seal
2 1.1 1.3 1.1 472 Seal face Performance Capabilities
d6 ±0.1
d2 +0.3
d5 min

d3 H7

473 Seal face housing

d4

d1

Sizes: d1 = Upto 100 mm (Upto 4.000’’)

3 1.4 1.2 1.2 485 Drive collar
Pressure: p1 = 25 bar (363 PSI)
1.3 O-ring Temperature: t = -40 °C...+180 °C
1.4 477 Spring (- 40 °F...+356 °F)
2 475 Rotating seat*) Speed = 50 m/s (164 ft/s)
3 412.2 O-ring
Materials
DIN 24250
8 2 *)
Seal face: Carbon graphite antimony
The seat design is chosen according to the impregnated (A), Carbon graphite resin
l1
specific requirements and conditions of impregnated (B)
Note: The item numbers as depicted above are based on our technical experience and operation.
knowledge and are placed in the chronological order of their assembly procedure.
Design Variations
Dimensional Data l1'
Dimensions in millimeter
B800
d1 d2 d2’ d3 d4 d5 d6 l l1 l 1’ Dimensions, items
15 16 17 42 22.6 21 34 17 15.0 16 and description as
18 19 - 45 25.6 24 37 17 15.0 - B100. Drive collars
20 21 22 48 27.6 26 40 17 15.0 16 and housings for
22 23 24 50 29.6 28 42 17 15.0 16 item 1.2 are made
25 26 27 52 32.8 31 44 17 15.0 16 1.2 of deepdrawn
28 29 - 55 35.8 34 47 17 15.0 - stainless steel
d2'

30 31 32 58 37.8 36 50 17 15.0 16 sheet.

32 33 34 60 39.8 38 52 17 15.0 16
35 36 37 62 42.8 41 54 17 15.0 16
38 39 40 65 45.9 44 57 17 15.0 16
40 41 42 68 47.9 46 60 17 15.0 16
42 43 44 72 49.9 48 64 17 15.0 16
45 46 47 75 52.9 51 67 17 15.0 16
48 49 - 80 55.9 54 72 17 15.0 -
50 51 52 80 58.2 56 72 17 15.0 16
52 53 - 82 60.2 58 74 17 15.0 -
55 56 57 85 63.2 61 77 17 15.0 16
58 59 - 90 66.7 64 82 17 15.0 -
60 61 62 90 68.7 66 82 17 15.0 16
65 66 67 95 73.7 71 87 19 16.5 18
68 69 70 100 76.7 74 92 19 16.5 18
70 71 72 100 78.7 76 92 19 16.5 18
75 76 77 108 83.7 81 100 19 16.5 18
80 81 82 112 88.7 86 104 19 16.5 18
85 86 87 118 93.7 91 110 19 16.5 18
90 91 92 122 99.5 96 114 19 16.5 18
95 96 97 128 104.5 101 120 19 16.5 18
100 101 102 132 109.5 106 124 19 16.5 18
inch size available from size 0.750 to 4.000
Note: Additional technical & dimensional information will be provided on request.
40
 BRN Single Seals Standard Mechanical Seals - Pusher Seals

Product Description Technical Features

1. Single seal configuration 1. Accommodates shaft deflections due to
2. Balanced design stationary design
3. Independent of direction of rotation 2. Designed to handle media containing
4. For plain shafts solids
5. Stationary design with multiple springs 3. O-ring is dynamically loaded to prevent
shaft damage.
4. Can operate under vacuum without
locking the seat
5. Pumping device available for increased
efficiency in circulation
6. Springs are product protected to avoid
contamination
7. Compact installation design
8. Can accommodate reverse pressure

l1k ±1 9
l3

f
mx

6 4 2 1.1 1.3 1.5

d 6 H11
d 7 H8
d1 h6
d10
d3

5 3 1.2 1.4
20

d8 Item Part no. Description

O

1.1 472 Seal face

l5 l6 5 1.2 412.1 O-ring
1.3 485 Retainer
1.4 477 Spring
Note: The item numbers as depicted above are based on our technical experience and
knowledge and are placed in the chronological order of their assembly procedure. 1.5 412.2 O-ring
2 475 Seat
3 412.3 O-ring
4 485 Drive collar
5 412.4 O-ring
6 904 Set screw
DIN 24250

41
 Typical Industrial Applications Performance Capabilities Materials
Chemical industry Sizes: d1 = Upto 100 mm (Upto 4.000’’) Seal face: Carbon graphite resin
Dirty, abrasive and solid containing media Pressure: p1*) = 25 bar (363 PSI) impregnated (B), Silicon carbide (Q1)
Fugitive hydrocarbons Temperature: t = - 40 °C .. +220 °C Seat: Silicon carbide (Q1)
Refining technology (-40 °F .. + 428 °F) Secondary seals: FKM (V), NBR (P),
Sticky and stringy media Speed = 20 m/s (66 ft/s) FFKM (K), PTFE (T)
Water and waste water technology Permissible axial movement: ± 1.0 mm Springs: Hastelloy® C-4 (M)
Chemical standard pumps *) Additional seat locking is not needed in Metal parts: CrNiMo steel (G)
Sewage pumps vacuum operation. For operation under vacuum
it is necessary to arrange for quenching on the Standards
atmosphere.
EN 12756

Dimensional Data
Dimensions in millimeter
d1 d3 d6 d7 d8 d10 I 1k I3 I5 I6 f mx
18 33 27 33 3 34.7 37.5 19.5 2.0 5 3.0 4
20 35 29 35 3 36.7 37.5 19.5 2.0 5 3.0 4
22 37 31 37 3 38.7 37.5 19.5 2.0 5 3.0 4
24 39 33 39 3 40.7 40.0 20.5 2.0 5 3.5 5
25 40 34 40 3 41.7 40.0 20.5 2.0 5 3.5 5
28 43 37 43 3 44.7 42.5 21.5 2.0 5 3.5 5
30 45 39 45 3 46.7 42.5 21.5 2.0 5 3.5 5
32 48 42 48 3 49.7 42.5 21.5 2.0 5 3.5 5
33 48 42 48 3 49.7 42.5 21.5 2.0 5 3.5 5
35 50 44 50 3 51.7 42.5 21.5 2.0 5 3.5 5
38 56 49 56 4 57.7 45.0 24.0 2.0 6 4.0 6
40 58 51 58 4 59.7 45.0 24.0 2.0 6 4.0 6
43 61 54 61 4 62.7 45.0 24.0 2.0 6 4.0 6
45 63 56 63 4 64.7 45.0 24.0 2.0 6 4.0 6
48 66 59 66 4 67.7 45.0 24.0 2.0 6 4.0 6
50 70 62 70 4 71.7 47.5 25.0 2.5 6 4.0 6
53 73 65 73 4 74.7 47.5 25.0 2.5 6 4.0 6
55 75 67 75 4 76.7 47.5 25.0 2.5 6 4.0 6
58 78 70 78 4 80.5 52.5 28.0 2.5 6 4.0 6
60 80 72 80 4 82.5 52.5 28.0 2.5 6 4.0 6
63 83 75 83 4 85.5 52.5 28.0 2.5 6 4.0 6
65 85 77 85 4 87.5 52.5 28.0 2.5 6 4.0 6
68 90 81 90 4 92.5 52.5 28.0 2.5 7 4.0 6
70 92 83 92 4 94.5 60.0 34.0 2.5 7 6.0 8
75 97 88 97 4 100.5 60.0 34.0 2.5 7 6.0 8
80 105 95 105 4 108.5 60.0 34.0 3.0 7 6.0 8
85 110 100 110 4 113.5 60.0 34.0 3.0 7 6.0 8
90 115 105 115 4 118.5 65.0 39.0 3.0 7 10.0 8
95 120 110 120 4 123.5 65.0 39.0 3.0 7 10.0 8
100 125 115 125 4 128.5 65.0 39.0 3.0 7 10.0 8
inch size available from size 0.750 to 4.000
Note: Additional technical & dimensional information will be provided on request.

42
 BJ920N Single Seals Standard Mechanical Seals - Pusher Seals

Product Description Technical Features

1. Single seal configuration 1. C o m p a c t d e s i g n w i t h r u g g e d
2. Balanced design construction
3. Independent of direction of rotation 2. Capable of withstanding high pressure
4. For plain shafts 3. O-ring is dynamically loaded to prevent
5. Rotary unit with encapsulated spring shaft damage.
design 4. Can handle media with solid content
and viscous media
5. Can handle sterile and vacuum
application
6. Springs are product protected to avoid
contamination

l1k Typical Industrial Applications

Conveying and bottling of dairy products
l3 l7 +0.5 Dirty, abrasive and solids containing media
Pulp and paper industry
f l19 Sugar industry
Water and waste water technology
Raw sludge pumps
mx Raw sludge, sewage slurries
Thick juice pumps

Performance Capabilities
Sizes: d1 = Upto 100 mm (Upto 4.000’’)
Pressure: p1*) = 0.8 abs... 25 bar
(12 abs.... 363 PSI)
Temperature: t = –50 °C...+220 °C
(–58 °F...+430 °F)
1.6 1.4 1.5 1.1 2 3 Speed = 20 m/s (66 ft /s)
d6 H11

d7 H8
d1 h6
dm

Permissible axial movement: ±0.5 mm

d3

*)
An integral stationary seat lock is not needed
l18
1.2 1.3 within the permissible low pressure range. For
prolonged operation under vacuum it is
necessary to arrange for quenching on the
atmospheric side.

Standards
EN 12756
20
O

d8
Notes
l5 l6 Variant for sterile applications available.
5 Please enquire.

Materials
Note: The item numbers as depicted above are based on our technical experience and
knowledge and are placed in the chronological order of their assembly procedure.
Seal face: Carbon graphite antimony
impregnated (A),
Carbon graphite resin impregnated (B)
Seat G16: Silicon carbide (Q1)

Item Part no. Description

1.1 472/473 Seal face
1.2 485 Drive collar
1.3 412.2 O-ring
1.4 412.1 O-ring
1.5 477 Spring
1.6 904 Set screw
2 475 Seat (G16)
3 412.3 O-ring
DIN 24250

43
 Design Variations
l11 l1k

l38
l38 1.6 1.4 1.1 2 3

l3 l39 1.2 1.3 1.5

l13 l39

BJ927GN BJ977GN BJ470

Items and description as BJ920N. Items and description as BJ920N. Mechanical seals with product-protected
Seal face: Carbon graphite antimony impregnated Seal face: Silicon carbide (Q12) multiple springs, for high pressure applications.
(A), Carbon graphite resin impregnated (B) Seat G46: Silicon carbide (Q12) Pressure: p = max. 50 bar (725 PSI)
Seat G46: Silicon carbide (Q12) Installation length l1k Shaft diameter: d1 > Upto 100 mm
1) Installations length l11 (= l3 + l39) is longer than l1k.
Operating range: (Upto 4.000’’).
Temperature: t = –20 °C ... +180 °C Smaller diameters and higher pressures on
(-4 °F ... +356 °F) request.
BJ970GN5 Speed = 10 m/s (33 ft /s)
Items and description as BJ920N.
Seal face: Silicon carbide (Q12)
Seat G16: Silicon carbide (Q1)
2) Installations length l12 (= l13 + l19)
is shorter than l1k.

Dimensional Data
Dimensions in millimeter
d1 d3 d6 d7 d8 dm l 1k l3 l5 l6 l7 l 18 l 19 l 11 1) l 122) l 13 l 38 l 39 f mx

18 32 27 33 3 26.0 37.5 30.5 2.0 5 9 15.0 7.0 39.5 35.5 28.5 17.0 9.0 3.0 M4
20 34 29 35 3 28.0 37.5 30.5 2.0 5 9 15.0 7.0 39.5 35.5 28.5 17.0 9.0 3.0 M4
22 36 31 37 3 30.0 37.5 30.5 2.0 5 9 15.0 7.0 39.5 35.5 28.5 17.0 9.0 3.0 M4
24 38 33 39 3 32.5 40.0 33.0 2.0 5 9 15.0 7.0 42.0 38.0 31.0 17.0 9.0 3.5 M5
25 39 34 40 3 33.5 40.0 33.0 2.0 5 9 15.0 7.0 42.0 38.0 31.0 17.0 9.0 3.5 M5
28 42 37 43 3 36.5 42.5 35.5 2.0 5 9 15.0 7.0 45.0 40.0 33.0 17.5 9.5 3.5 M5
30 44 39 45 3 38.5 42.5 35.5 2.0 5 9 15.0 7.0 45.0 40.0 33.0 17.5 9.5 3.5 M5
32 47 42 48 3 41.5 42.5 35.5 2.0 5 9 15.0 7.0 45.0 40.0 33.0 17.5 9.5 3.5 M5
33 47 42 48 3 41.5 42.5 35.5 2.0 5 9 15.0 7.0 45.0 40.0 33.0 17.5 9.5 3.5 M5
35 49 44 50 3 43.5 42.5 35.5 2.0 5 9 15.0 7.0 45.0 40.0 33.0 17.5 9.5 3.5 M5
38 54 49 56 4 47.5 45.0 37.0 2.0 6 9 16.0 8.0 47.5 42.5 34.5 18.5 10.5 4.0 M5
40 56 51 58 4 49.5 45.0 37.0 2.0 6 9 16.0 8.0 47.5 42.5 34.5 18.5 10.5 4.0 M5
43 59 54 61 4 52.5 45.0 37.0 2.0 6 9 16.0 8.0 47.5 42.5 34.5 18.5 10.5 4.0 M5
45 61 56 63 4 54.5 45.0 37.0 2.0 6 9 16.0 8.0 47.5 42.5 34.5 18.5 10.5 4.0 M5
48 64 59 66 4 57.5 45.0 37.0 2.0 6 9 16.0 8.0 47.5 42.5 34.5 18.5 10.5 4.0 M5
50 66 62 70 4 59.5 47.5 38.0 2.5 6 9 17.0 9.5 50.0 45.0 35.5 19.5 12.0 4.5 M6
53 69 65 73 4 62.5 47.5 38.0 2.5 6 9 17.0 9.5 50.0 45.0 35.5 19.5 12.0 4.5 M6
55 71 67 75 4 64.5 47.5 38.0 2.5 6 9 17.0 9.5 50.0 45.0 35.5 19.5 12.0 4.5 M6
58 78 70 78 4 68.5 52.5 42.0 2.5 6 9 18.0 10.5 55.0 50.0 39.5 20.5 13.0 4.5 M6
60 80 72 80 4 70.5 52.5 42.0 2.5 6 9 18.0 10.5 55.0 50.0 39.5 20.5 13.0 4.5 M6
63 83 75 83 4 73.5 52.5 42.0 2.5 6 9 18.0 10.5 55.0 50.0 39.5 20.5 13.0 4.5 M6
65 85 77 85 4 75.5 52.5 42.0 2.5 6 9 18.0 10.5 55.0 50.0 39.5 20.5 13.0 4.5 M6
68 88 81 90 4 78.5 52.5 41.5 2.5 7 9 18.5 11.0 55.0 50.0 39.0 21.0 13.5 4.5 M6
70 90 83 92 4 80.5 60.0 48.5 2.5 7 9 19.0 11.5 62.5 57.5 46.0 21.5 14.0 5.0 M6
75 99 88 97 4 89.0 60.0 48.5 2.5 7 9 19.0 11.5 62.5 57.5 46.0 21.5 14.0 5.5 M8
80 104 95 105 4 94.0 60.0 48.5 3.0 7 9 19.0 11.5 62.5 57.5 46.0 21.5 14.0 5.5 M8
85 109 100 110 4 99.0 60.0 48.5 3.0 7 9 19.0 11.5 62.5 57.5 46.0 21.5 14.0 5.5 M8
90 114 105 115 4 104.0 65.0 52.0 3.0 7 9 20.5 13.0 67.5 62.5 49.5 23.0 15.5 5.5 M8
95 119 110 120 4 109.0 65.0 52.0 3.0 7 9 20.5 13.0 67.5 62.5 49.5 23.0 15.5 5.5 M8
100 124 115 125 4 114.0 65.0 52.0 3.0 7 9 20.5 13.0 67.5 62.5 49.5 23.0 15.5 5.5 M8
inch size available from size 0.750 to 4.000
Note: Additional technical & dimensional information will be provided on request.
44
 B700N Single Seals Standard Mechanical Seals - Pusher Seals

Product Description Technical Features

1. Single seal configuration 1. Versatile torque transmission available
2. Balanced design 2. Capable of self cleaning
3. Independent of direction of rotation 3. Short installation length available on
4. For stepped shafts request
5. Multiple or wave springs rotary 4. Multifaceted application usage
construction
6. Pumping device available for increased
efficiency in circulation (B700F, B750F)
7. High temperature application with
cooled stationary seats available

l1k
Typical Industrial Applications Materials
l3 l9
f
Boiler feed pumps Seal face: Silicon carbide (Q1, Q2), Carbon
Hot water applications graphite antimony impregnated (A),
mx Light hydrocarbons Aluminium oxide (V), CrMo cast steel (S)
Oil and gas industry Seat G9: Carbon graphite antimony impregnated
Petrochemical industry (A), Carbon graphite resin impregnated (B),
Power plant technology Silicon carbide (Q1*, Q2*)
Process pumps Secondary seals: EPDM (E), NBR (P),
Refining technology
10 O 1)

1.6 1.5 1.4 2 3

d 6 H11 3)

FKM (V), FFKM (K)

d 7 H8 4)
(>100=h8)
d2 h6

d1
d3

l8
Springs: CrNiMo steel (G)
1.2 1.3 R1.6 1.1 Standards
Metal parts: CrNiMo steel (G), Duplex (G1)
EN 12756 * Cannot be combined with seal face made of S
Performance Capabilities
20 O 2)
20

d8 Torque Transmissions
O

Sizes: d1 =Upto 100 mm (Upto 4.000’’)

1) l5 l6 5
3 (Single spring: d1 = max. Upto 100 mm
l2 l7 +0.5 (Upto 4.000’’) d1 > 100 mm (4.000")
Pressure: Torque transmission
Note: The item numbers as depicted above are based on our technical experience and
knowledge and are placed in the chronological order of their assembly procedure. p1 = 80 bar (1160 PSI) for d1 = 14 ... 100 mm, by 4 set screws with
p1 = 25 bar (363 PSI) for d1 = 100 ... 200 mm, cone point. Offset:
90°
p1 = 16 bar (232 PSI) for d1 > 200 mm
Temperature: t = - 50 °C...+220 °C
Item Part no. Description (-58 °F...+428 °F) umax
-0.2

Speed = 20 m/s (66 ft /s)

t

1.1 472 Seal face Permissible axial movement: Drive key

1.2 485 Drive collar d1 up to 22 mm: ± 1.0 mm (B700S2 / B750S2)
min

1.3 474 Thrust ring d1 24 up to 58 mm: ± 1.5 mm

d24
b

1.4 412.1 O-ring d1 from 60 mm: ± 2.0 mm

1.5 477 Spring
1) d1 > 100 mm: 2 mm x 30°
1.6 904 Set screw
2) d1 > 100 mm: 30°
2 475 Seat (G9)
3) d1 > 100 mm: +0.1
3 412.2 O-ring
DIN 24250 4) d1 > 100 mm: H7

Stationary Seats
l40 a
l6 l6 4.1
+0.1
h1
l5 l5
20 O
20 O

G9 G16 G115
-0.05
d21 +0.1
d1

d22

(EN 12756) l19 (EN 12756, but l1k Cooled seat

Ø 5
d6 H11

d7 H8

d6 H11

especially for hot

d7 H8

l18 and l2 are shorter

than specified) water applications.
k e
h2
l39

45
 Design Variations

0.5
d s -0.05
(>100 -0.1)
± 2 .... 4 mm ± 4 mm ± 1 ... 2 mm
l 1k l 1N l 1K

B750 B760 B700F

Shaft diameter: d1 = Upto 200 mm (Upto 7.875”) Shaft diameter: d1 = Upto 100mm (Upto 4.000”) Shaft diameter : d1 = max. Upto 100mm
As B700N, but with multiple springs in sleeves Dimensions, items and description as for (Upto 4.000”)
(Item no.1.5) B700N, but with special single spring (Item no. Dimensions, items and descriptions as for
Axial movement: ± 2 ... 4 mm, dependent on 1.5) for compensating large axial movements B700N, but with single spring and pumping
diameter (± 4 mm). screw.
Dependent on direction of rotation.
(Viscosity < ISO VG10).
B750F
Shaft diameter: d1 = Upto 200 mm (Upto 7.875’’)
Dimensions, items and descriptions as for
B700N, but with single spring and pumping
screw.
Dependent on direction of rotation.
(Viscosity < ISO VG10).

Dimensional Data
Dimensions in millimeter
d1 d2 d3 d6 d 7 d 8 d 24 d 21 d 22 ds l 1K l 1N l2 l3 l5 l6 l7 l8 l9 l 18 l 19 l 39 l 40 a b e f h1 h2 k m x umax. t
14* 18 33 21 25 3 20 - - 38 42.5 - 18 32.5 1.5 4 8.5 17.5 10.0 - - - - - 5 - 6.0 - - - M5 9 1.1
16* 20 35 23 27 3 22 - - 40 42.5 - 18 32.5 1.5 4 8.5 17.5 10.0 - - - - - 5 - 6.0 - - - M5 9 1.1
18* 22 37 27 33 3 24 - - 42 45.0 55 20 33.5 2.0 5 9.0 19.5 11.5 15.0 7.0 - - - 6 - 7.0 - - - M5 9 1.5
20* 24 39 29 35 3 26 - - 44 45.0 60 20 33.5 2.0 5 9.0 19.5 11.5 15.0 7.0 - - - 6 - 5.5 - - - M5 9 1.5
22* 26 41 31 37 3 28 - - 45 45.0 60 20 33.5 2.0 5 9.0 19.5 11.5 15.0 7.0 - - - 6 - 8.0 - - - M5 9 1.5
24* 28 43 33 39 3 30 - - 47 47.5 60 20 36.0 2.0 5 9.0 19.5 11.5 15.0 7.0 - - - 6 - 5.5 - - - M6 9 1.5
25* 30 45 34 40 3 32 - - 49 47.5 60 20 36.0 2.0 5 9.0 19.5 11.5 15.0 7.0 - - - 6 - 5.5 - - - M6 9 1.5
28* 33 48 37 43 3 35 44.65 50.57 51 50.0 65 20 38.5 2.0 5 9.0 19.5 11.5 15.0 7.0 24.0 8.5 24.0 6 8.0 8.0 6.6 22.6 9 M6 12 1.5
30* 35 50 39 45 3 37 47.83 53.75 54 50.0 65 20 38.5 2.0 5 9.0 19.5 11.5 15.0 7.0 24.5 9.0 24.0 6 8.0 8.0 6.6 22.6 9 M6 12 1.5
32* 38 55 42 48 3 40 47.83 53.75 59 50.0 65 20 38.5 2.0 5 9.0 19.5 11.5 15.0 7.0 24.5 9.0 24.0 6 8.0 8.0 6.6 22.6 9 M6 12 1.5
33* 38 55 42 48 3 40 47.83 53.75 59 50.0 65 20 38.5 2.0 5 9.0 19.5 11.5 15.0 7.0 24.5 9.0 24.0 6 8.0 8.0 6.6 22.6 9 M6 12 1.5
35* 40 57 44 50 3 42 51.00 56.92 61 50.0 65 20 38.5 2.0 5 9.0 19.5 11.5 15.0 7.0 24.5 9.0 24.0 6 8.0 8.0 6.6 22.6 9 M6 12 1.5
38* 43 60 49 56 4 45 54.18 60.10 65 52.5 75 23 38.5 2.0 6 9.0 22.0 14.0 16.0 8.0 26.0 11.0 24.0 6 8.0 8.0 6.6 22.6 9 M6 12 1.5
40* 45 62 51 58 4 47 60.53 66.45 66 52.5 75 23 38.5 2.0 6 9.0 22.0 14.0 16.0 8.0 26.0 11.0 24.0 6 8.0 8.0 6.6 22.6 9 M6 12 1.5
43* 48 65 54 61 4 50 63.70 69.62 69 52.5 75 23 38.5 2.0 6 9.0 22.0 14.0 16.0 8.0 26.0 11.0 24.0 6 8.0 8.0 6.6 22.6 9 M6 12 1.5
45* 50 67 56 63 4 52 63.70 69.62 71 52.5 75 23 38.5 2.0 6 9.0 22.0 14.0 16.0 8.0 26.0 11.0 24.0 6 8.0 8.0 6.6 22.6 9 M6 12 1.5
48* 53 70 59 66 4 55 66.88 72.80 75 52.5 85 23 38.5 2.0 6 9.0 22.0 14.0 16.0 8.0 26.0 11.0 24.0 6 8.0 8.0 6.6 22.6 9 M6 12 1.5
50* 55 72 62 70 4 57 70.05 75.97 76 57.5 85 25 42.5 2.5 6 9.0 23.0 15.0 17.0 9.5 26.5 12.5 24.0 6 8.0 8.0 6.6 24.6 9 M6 12 1.5
53* 58 79 65 73 4 60 76.40 82.32 83 57.5 85 25 42.5 2.5 6 9.0 23.0 15.0 17.0 9.5 26.5 12.5 24.0 8 8.0 9.0 6.6 24.6 9 M8 12 1.9
55* 60 81 67 75 4 62 76.40 82.32 85 57.5 85 25 42.5 2.5 6 9.0 23.0 15.0 17.0 9.5 28.5 12.5 26.0 8 8.0 9.0 6.6 24.6 11 M8 12 1.9
58* 63 84 70 78 4 65 79.58 85.50 88 62.5 85 25 47.5 2.5 6 9.0 23.0 15.0 18.0 10.5 28.5 12.5 26.0 8 8.0 9.0 6.6 24.6 11 M8 15 1.9
60* 65 86 72 80 4 67 82.75 88.67 95 62.5 95 25 47.5 2.5 6 9.0 23.0 15.0 18.0 10.5 28.5 12.5 26.0 8 8.0 9.0 6.6 24.6 11 M8 15 1.9
63* 68 89 75 83 4 70 85.93 91.85 93 62.5 95 25 47.5 2.5 6 9.0 23.0 15.0 18.0 10.5 28.5 12.5 26.0 8 8.0 9.0 6.6 24.6 11 M8 14 1.9
65* 70 91 77 85 4 72 85.93 91.85 95 62.5 95 25 47.5 2.5 6 9.0 23.0 15.0 18.0 10.5 28.5 12.5 26.0 8 8.0 9.0 6.6 24.6 11 M8 15 1.9
70* 75 99 83 92 4 77 89.10 95.02 105 70.0 95 28 52.0 2.5 7 9.0 26.0 18.0 19.0 11.5 30.5 14.5 26.0 8 8.0 10.0 6.6 24.6 11 M8 15 1.9
75* 80 104 88 97 4 82 98.63 104.55 109 70.0 105 28 52.0 2.5 7 9.0 26.0 18.0 19.0 11.5 30.5 14.5 26.0 8 8.0 10.0 6.6 24.6 11 M8 15 1.9
80* 85 109 95 105 4 87 101.80 107.72 114 70.0 105 28 51.8 3.0 7 9.0 26.2 18.2 19.0 11.5 30.2 14.0 26.0 8 8.0 10.0 6.6 24.6 11 M8 15 1.9
85* 90 114 100 110 4 92 108.15 114.07 119 75.0 105 28 56.8 3.0 7 9.0 26.2 18.2 19.0 11.5 30.2 14.0 26.0 10 8.0 10.0 6.6 24.6 11 M8 18 2.3
90* 95 119 105 115 4 97 114.50 120.42 124 75.0 105 28 56.8 3.0 7 9.0 26.2 18.2 20.5 13.0 30.2 14.0 26.0 10 8.0 10.0 6.6 24.6 11 M8 18 2.3
95* 100 124 110 120 4 102 117.68 123.60 129 75.0 105 28 57.8 3.0 7 9.0 25.2 17.2 20.5 13.0 29.2 14.0 26.0 10 8.0 10.0 6.6 24.6 11 M8 18 2.3
100* 105 129 115 125 4 107 124.03 129.95 134 75.0 105 28 57.8 3.0 7 9.0 25.2 17.2 20.5 13.0 29.2 14.0 26.0 10 8.0 10.0 6.6 24.6 11 M8 18 2.3
105* 115 148 122.2 134.3 5 118 128.98 134.90 153 73.0 - 32 53.0 2.0 10 - 30.0 20.0 - - 29.2 15.2 26.0 10 8.0 10.0 6.6 24.6 11 M8 18 2.3
110* 120 153 128.2 140.3 5 123 135.30 141.20 158 73.0 - 32 53.0 2.0 10 - 30.0 20.0 - - 32.5 14.5 30.0 10 9.5 10.0 6.6 28.6 13 M8 18 2.3
115* 125 158 136.2 148.3 5 128 140.30 146.20 163 73.0 - 32 53.0 2.0 10 - 30.0 20.0 - - 32.5 14.5 30.0 10 9.5 10.0 6.6 28.6 13 M8 18 2.3
120* 130 163 138.2 150.3 5 133 145.30 151.20 168 73.0 - 32 53.0 2.0 10 - 30.0 20.0 - - 32.5 14.5 30.0 10 9.5 10.0 6.6 28.6 13 M8 18 2.3
125* 135 168 142.2 154.3 5 138 150.30 156.20 173 73.0 - 32 53.0 2.0 10 - 30.0 20.0 - - 32.5 14.5 30.0 10 9.5 10.0 6.6 28.6 13 M8 18 2.3
130* 140 173 146.2 158.3 5 143 155.30 161.20 178 73.0 - 32 53.0 2.0 10 - 30.0 20.0 - - 32.5 14.5 30.0 10 9.5 10.0 6.6 28.6 13 M8 18 2.3
135* 145 178 152.2 164.3 5 148 160.30 166.20 183 73.0 - 32 53.0 2.0 10 - 30.0 20.0 - - 32.5 14.5 30.0 10 9.5 10.0 6.6 28.6 13 M8 18 2.3
140* 150 183 156.2 168.3 5 153 165.30 171.20 188 73.0 - 32 53.0 2.0 10 - 30.0 20.0 - - 32.5 14.5 30.0 10 9.5 10.0 6.6 28.6 13 M8 18 2.3
145* 155 191 161.2 173.3 5 158 172.30 178.20 196 83.0 - 34 63.0 2.0 10 - 30.0 20.0 - - 34.5 16.5 32.0 12 10.0 12.0 7.1 30.1 14 M8 22 2.1
150* 160 196 168.2 180.3 5 163 177.30 183.20 201 85.0 - 36 63.0 2.0 10 - 32.0 22.0 - - 34.5 16.5 32.0 12 10.0 12.0 7.1 30.1 14 M8 22 2.1
155* 165 201 173.2 185.3 5 168 182.30 188.20 206 87.0 - 38 63.0 2.0 12 - 34.0 24.0 - - 34.5 16.5 32.0 12 10.0 12.0 7.1 30.1 14 M8 22 2.1
160* 170 206 178.2 190.3 5 173 187.30 193.20 211 87.0 - 38 63.0 2.0 12 - 34.0 24.0 - - 34.5 16.5 32.0 12 10.0 12.0 7.1 30.1 14 M8 22 2.1
165* 175 211 183.2 195.3 5 178 192.30 198.20 216 87.0 - 38 63.0 2.0 12 - 34.0 24.0 - - 34.5 16.5 32.0 12 10.0 12.0 7.1 30.1 14 M8 22 2.1
170* 180 216 188.2 200.3 5 183 197.30 203.20 221 87.0 - 38 63.0 2.0 12 - 34.0 24.0 - - 37.0 16.5 34.5 12 10.0 12.0 7.1 32.1 16 M8 22 2.1
175* 185 221 193.2 205.3 5 188 202.30 208.20 226 87.0 - 38 63.0 2.0 12 - 34.0 24.0 - - 37.0 16.5 34.5 12 10.0 12.0 7.1 32.1 16 M8 22 2.1
180* 190 226 207.5 219.3 5 193 207.30 213.20 231 91.0 - 42 63.0 2.0 12 - 38.0 28.0 - - 37.0 16.5 34.5 12 10.0 12.0 7.1 32.1 16 M8 22 2.1
185* 195 231 212.5 224.3 5 198 212.30 218.20 236 91.0 - 42 63.0 2.0 12 - 38.0 28.0 - - 37.0 16.5 34.5 12 10.0 12.0 7.1 32.1 16 M8 22 2.1
190* 200 236 217.5 229.3 5 203 217.30 223.20 241 91.0 - 42 63.0 2.0 12 - 38.0 28.0 - - 37.0 16.5 34.5 12 10.0 12.0 7.1 32.1 16 M8 22 2.1
195* 205 245 222.5 234.2 5 208 225.30 231.20 250 94.0 - 43 66.0 2.0 12 - 38.0 28.0 - - 37.0 17.5 34.5 12 10.0 14.0 7.1 32.1 16 M10 22 2.1
200* 210 250 227.5 239.3 5 213 230.30 236.20 255 94.0 - 43 66.0 2.0 12 - 38.0 28.0 - - 37.0 17.5 34.5 12 10.0 14.0 7.1 32.1 16 M10 22 2.1
*EN 12756
d1 > 200 on request
inch size available from size 0.625 to 7.875
Note: Additional technical & dimensional information will be provided on request.
46
 B740-D Dual Seals Standard Mechanical Seals - Pusher Seals

Product Description Technical Features

1. Dual seal configuration 1. Versatile torque transmission available
2. Balanced design 2. Capable of self cleaning
3. Independent of direction of rotation 3. Multifaceted application usage
4. For stepped shafts 4. Pumping device to increase efficiency
5. Rotary unit with multiple springs in circulation for media with higher
6. Pumping device available for increased viscosity available
efficiency in circulation (B740F-D) 5. Short installation length available
6. Suitable for media with low solids
content
7. EN 12756 (For connection dimensions
d1 up to 100 mm)

Typical Industrial Applications

l1
Adhesives
l 7+0.5 l2 l 31 l2 Chemical industry
l8 l4 l8 Media with poor lubrication properties
Media with low solids content and abrasive
particles
mx Process industry
1)
3 Toxic and hazardous media
Chemical standard pumps
Performance Capabilities
Sizes: d1 = Upto 200 mm (Upto 7.875’’)
.6
R1 Pressure:
O1
)

3 2 1.1 1.7 1.3 1.5 1.6 1.4 1.8 1.2 4 5

4)

10

p1 = 80 bar (1160 PSI) for d1 = 14 ... 100 mm,

3)

d 6 H11
d 7 H8

d3
d1
d2 h6

p1 = 25 bar (363 PSI) for d1 = 100 ... 200 mm,

>100 h8

p1 = 16 bar (232 PSI) for d1 > 200 mm

20 O 2)

Temperature: t = -50 °C...+220 °C

(- 58 °F...+428 °F)
Speed = 20 m/s (66 ft /s)
Permissible axial movement:
d8 d1 up to 100 mm: ± 0.5 mm
5 l9 l3 l5 l6 d1 from 100 mm: ± 2.0 mm
Standards
Note: The item numbers as depicted above are based on our technical experience and
knowledge and are placed in the chronological order of their assembly procedure. EN 12756
Torque Transmission

Stationary Seats
l6 l 16
l5 l 15 d2 > 105 mm VIA 4 set
Item Part no. Description
20 O

screws with cone points.

30

1.1 472.1 Seal face (standard arrangement)

d 12 H7
+0.1

1.2 472.2 Seal face l28 l 14

d6 H11

d 11 +0.1
H8

l 10
l 12
1.3 474 Thrust ring
d7

1.4 485 Drive collar

1.5 477 Spring G6 (EN 12756) G4
1.6 904 Set screw Materials
1.7 412.1 O-ring Seal face: Silicon carbide (Q1, Q2), Carbon
1.8 412.2 O-ring graphite antimony impregnated (A),
2 475.1 Seat (G9) Aluminium oxide (V), Special cast CrMo steel (S)
1)
3 412.3 O-ring d1 > 100 mm: 2 mm x 30° Seat G9: Carbon graphite antimony impregnated
4 475.2 Seat (G9)
2)
d1 > 100 mm: 30° (A), Carbon graphite resin impregnated (B),
5 412.4 O-ring
3)
d1 > 100 mm: H7 Silicon carbide (Q1*, Q2*)
DIN 24250 4)
d1 > 100 mm: +0.1
Secondary seals: EPDM (E), NBR (P),
FKM (V), FFKM (K)
Springs: CrNiMo steel (G)
Metal parts: CrNiMo steel (G), Duplex (G1)
* Cannot be combined with seal face made of S

47
 Design Variations

0.5
B740F-D

(>100 - 0.1)
Dimensions, items and descriptions as for

ds -0.05
B740-D, but with pumping screw (Item no. 1.4)
Dependent on direction of rotation.

Dimensional Data
Dimensions in millimeter
d1 d2 d3 d6 d7 d8 d11 d12 ds l1 l2 l3 l4 l5 l6 l7 l8 l9 l 10 l 12 l 14 l 15 l 16 l 28 l 31 mx R
14 18 33 21.0 25 3 20.5 24.6 - 73 18 53 26.5 1.5 4 8.5 17.5 10 7.5 6.5 5.6 1.5 5 6.6 17 M5 1.2
16 20 35 23.0 27 3 22.0 28.0 - 73 18 53 26.5 1.5 4 8.5 17.5 10 7.5 8.5 7.5 1.5 5 6.6 17 M5 1.5
18 22 37 27.0 33 3 24.0 30.0 42 76 20 53 26.5 2 5 9 19.5 11.5 8.5 9 8 1.5 5 7.5 17 M5 1.5
20 24 39 29.0 35 3 29.5 35.0 44 76 20 53 26.5 2 5 9 19.5 11.5 8.5 8.5 7.5 1.5 5 7.5 17 M5 1.5
22 26 41 31.0 37 3 29.5 35.0 45 76 20 53 26.5 2 5 9 19.5 11.5 8.5 8.5 7.5 1.5 5 7.5 17 M5 1.5
24 28 43 33.0 39 3 32.0 38.0 47 77 20 54 27 2 5 9 19.5 11.5 8.5 8.5 7.5 1.5 5 7.5 17.5 M6 1.5
25 30 45 34.0 40 3 32.0 38.0 49 77 20 54 27 2 5 9 19.5 11.5 8.5 8.5 7.5 1.5 5 7.5 17.5 M6 1.5
28 33 48 37.0 43 3 36.0 42.0 51 77 20 54 27 2 5 9 19.5 11.5 8.5 10 9 1.5 5 7.5 17.5 M6 1.5
30 35 50 39.0 45 3 39.2 45.0 54 77 20 54 27 2 5 9 19.5 11.5 8.5 11.5 10.5 1.5 5 7.5 17.5 M6 1.5
32 38 55 42.0 48 3 42.2 48.0 59 79 20 56 28 2 5 9 19.5 11.5 8.5 11.5 10.5 1.5 5 7.5 18.5 M6 1.5
33 38 55 42.0 48 3 44.2 50.0 59 79 20 56 28 2 5 9 19.5 11.5 8.5 12 10.5 1.5 5 7.5 18.5 M6 1.5
35 40 57 44.0 50 3 46.2 52.0 61 80 20 57 28.5 2 5 9 19.5 11.5 8.5 12 11 1.5 5 7.5 19 M6 1.5
38 43 60 49.0 56 4 49.2 55.0 65 85 23 57 28.5 2 6 9 22 14 10 11.3 10.3 2 6 9 19 M6 1.5
40 45 62 51.0 58 4 52.2 58.0 66 85 23 57 28.5 2 6 9 22 14 10 11.8 10.8 2 6 9 19 M6 1.5
43 48 65 54.0 61 4 53.3 62.0 69 85 23 57 28.5 2 6 9 22 14 10 13.2 12 2 6 9 19 M6 2.5
45 50 67 56.0 63 4 55.3 64.0 71 84 23 56 28 2 6 9 22 14 10 12.8 11.6 2 6 9 19.5 M6 2.5
48 53 70 59.0 66 4 59.7 68.4 75 84 23 56 28 2 6 9 22 14 10 12.8 11.6 2 6 9 19.5 M6 2.5
50 55 72 62.0 70 4 60.8 69.3 76 93 25 63 31.5 2.5 6 9 23 15 10.5 12.8 11.6 2 6 9.5 19.5 M6 2.5
53 58 79 65.0 73 4 63.8 72.3 83 97 25 67 33.5 2.5 6 9 23 15 12 13.5 12.3 2 6 11 23.5 M8 2.5
55 60 81 67.0 75 4 66.5 75.4 85 97 25 67 33.5 2.5 6 9 23 15 12 14.5 13.3 2 6 11 23.5 M8 2.5
58 63 84 70.0 78 4 69.5 78.4 88 104 25 74 37 2.5 6 9 23 15 12 14.5 13.3 2 6 11 24.5 M8 2.5
60 65 86 72.0 80 4 71.5 80.4 95 104 25 74 37 2.5 6 9 23 15 12 14.5 13.3 2 6 11 24.5 M8 2.5
63 68 89 75.0 83 4 74.5 83.4 93 109 25 79 39.5 2.5 6 9 23 15 12 14.2 13.3 2 6 11 24.5 M8 2.5
65 70 91 77.0 85 4 76.5 85.4 95 98 25 68 34 2.5 6 9 23 15 12 14.2 13 2 6 11 23.5 M8 2.5
70 75 99 83.0 92 4 83.0 92.0 105 112.5 28 76.4 38.2 2.5 7 9 26 18 12.5 14.9 13.7 2 6 11.3 25.5 M8 2.5
75 80 104 88.0 97 4 90.2 99.0 109 112.5 28 76.4 38.2 2.5 7 9 26 18 12.5 14.2 13 2 6 11.3 25.5 M8 2.5
80 85 109 95.0 105 4 95.2 104.0 114 112.5 28 76 38 3 7 9 26.2 18.2 12.5 15.2 14 2 6 11.3 25 M8 2.5
85 90 114 100.0 110 4 100.2 109.0 119 112.5 28 76 38 3 7 9 26.2 18.2 13 16.2 15 2 6 12 25.5 M8 2.5
90 95 119 105.0 115 4 105.2 114.0 124 112.5 28 76 38 3 7 9 26.2 18.2 15 16 14.8 2 6 14 25 M8 2.5
95 100 124 110.0 120 4 111.6 120.3 129 110.5 28 76 38 3 7 9 25.2 17.2 15 16 14.8 2 6 14 25 M8 2.5
100 105 129 115.0 125 4 114.5 123.3 134 110.5 28 76 38 3 7 9 25.2 17.2 15 17 15.8 - - 14 25.5 M8 2.5
105 115 148 122.2 134.3 5 - - 153 122 32 82 41 2 10 - 30 20 15 17 15.8 - - 14 31.5 M8 2.5
110 120 153 128.2 140.3 5 - - 158 122 32 82 41 2 10 - 30 20 - - - - - - 31.5 M8 -
115 125 158 136.2 148.3 5 - - 163 122 32 82 41 2 10 - 30 20 - - - - - - 31.5 M8 -
120 130 163 138.2 150.3 5 - - 168 122 32 82 41 2 10 - 30 20 - - - - - - 31.5 M8 -
125 135 168 142.2 154.3 5 - - 173 122 32 82 41 2 10 - 30 20 - - - - - - 31.5 M8 -
130 140 173 146.2 158.3 5 - - 178 122 32 82 41 2 10 - 30 20 - - - - - - 31.5 M8 -
135 145 178 152.2 164.3 5 - - 183 122 32 82 41 2 10 - 30 20 - - - - - - 31.5 M8 -
140 150 183 156.2 168.3 5 - - 188 122 32 82 41 2 10 - 30 20 - - - - - - 31.5 M8 -
145 155 191 161.2 173.3 5 - - 196 133 34 93 46.5 2 10 - 30 20 - - - - - - 35.5 M8 -
150 160 196 168.2 180.3 5 - - 201 137 36 93 46.5 2 10 - 32 22 - - - - - - 35.5 M8 -
155 165 201 173.2 185.3 5 - - 206 141 38 93 46.5 2 12 - 34 24 - - - - - - 35.5 M8 -
160 170 206 178.2 190.3 5 - - 211 141 38 93 46.5 2 12 - 34 24 - - - - - - 35.5 M8 -
165 175 211 183.2 195.3 5 - - 216 141 38 93 46.5 2 12 - 34 24 - - - - - - 35.5 M8 -
170 180 216 188.2 200.3 5 - - 221 141 38 93 46.5 2 12 - 34 24 - - - - - - 35.5 M8 -
175 185 221 193.2 205.3 5 - - 226 141 38 93 46.5 2 12 - 34 24 - - - - - - 35.5 M8 -
180 190 226 207.5 219.3 5 - - 231 149 42 93 46.5 2 12 - 38 28 - - - - - - 35.5 M8 -
185 195 231 212.5 224.3 5 - - 236 149 42 93 46.5 2 12 - 38 28 - - - - - - 35.5 M8 -
190 200 236 217.5 229.3 5 - - 241 149 42 93 46.5 2 12 - 38 28 - - - - - - 35.5 M8 -
195 205 245 222.5 234.3 5 - - 250 151 43 95 47.5 2 12 - 38 28 - - - - - - - M10 -
200 210 250 227.5 239.3 5 - - 255 151 43 95 47.5 2 12 - 38 28 - - - - - - - - -
d1 > 200 on request
inch size available from size 0.625 to 7.875
Note: Additional technical & dimensional information will be provided on request.

48
 B120N Single Seals Standard Mechanical Seals - Pusher Seals

Product Description Technical Features

1. Single seal configuration 1. Low cost seal solution
2. Balanced design 2. No damage to the shaft
3. Dependent of direction of rotation 3. Short installation length available on
4. For stepped shafts request
5. Torque transmission is through the
conical spring

b l1 Design Variations
l3 l9 B120
Dimensions, items and descriptions as for
B120N, but with seat G16.
Seal face: Carbon graphite antimony
impregnated (A)
Seat G16: Silicon carbide (Q1), CrMo cast steel
(S), Aluminium oxide (V)

B170GN

1.4 1.3 1.2 1.1 2 3

10 O

d 6 H11
d 7 H8
d b min
d3

d1
d2 h6

l8 l9
R1
.6

l3 l8

20 O
d8
Dimensions, items and descriptions as for
3 l5 l6 5 B120N, but with shrink-fitted seal face (Q12),
item no. 1.1.
l2 l7 +0.5
Temperature: t =-20°C...+180°C (-4°F...+356 °F)
l1N Seal face: Silicon carbide (Q12)
Seat G9: Silicon carbide (Q1, Q2), Carbon
graphite antimony impregnated (A), Carbon
Note: The item numbers as depicted above are based on our technical experience and
knowledge and are placed in the chronological order of their assembly procedure.
graphite resin impregnated (B)

B170G
Typical Industrial Applications Dimensions, items and descriptions as for
Item Part no. Description Chemical industry B120N, but with shrink-fitted seal face (Q12) and
1.1 472/473 Seal face Hot water seat G16.
Medias with Low solids content (B170GN) Temperature: t = -20°C...+180°C (-4 °F... +356 °F)
1.2 412.1 O-ring Water and waste water technology Seal face: Silicon carbide (Q12)
1.3 474 Thrust ring Chemical standard pumps Seat G16 : Silicon carbide (Q1)
1.4 478 Right hand spring Water and sewage pumps

1.4 479 Left hand spring Performance Capabilities Materials

2 475 Seat (G9) Sizes: d1 = Upto 80 mm (Upto 3.15’’) Seal face: Carbon graphite antimony
3 412.2 O-ring impregnated (A)
Pressure: p1 = 25 bar (363 PSI) Seat G 9 : Silicon carbide (Q1), Special cast CrMo
DIN 24250 Temperature: t = -50 °C...+220 °C steel (S)
(- 58 °F...+430 °F)
Speed = 15 m/s (50 ft/s) Standards
Permissible axial movement: ± 1.0 mm
EN 12756

49
 Stationary Seats

l6 l40 a

l5 4.1
+0.1
h1
20 O

G115
G16 Cooled seat especially
(EN 12756 but l1k and l2 for hot water

-0.05
applications. In this

d21 +0.1
l19 are shorter than

d1

d22
H11 specified) case, the dimensions of

Ø 5
H8
l18 the B120N rotating unit
are modified. Seal
d6
d7
designation: B721G115.
k e
h2
l39

Dimensional Data
Dimensions in millimeter
d1 d2 d3 d6 d7 d8 d21 d22 db l 1N l1 l2 l3 l5 l6 l7 l8 l9 l 18 l 19 l 39 l 40 a b e h1 h2 k b*)

10 14 24 17 21 3 - - 18 50 35.5 18 25.5 1.5 4 8.5 17.5 10.0 - - - - - 5 - - - - 8.0

12 16 26 19 23 3 - - 21 50 36.5 18 26.5 1.5 4 8.5 17.5 10.0 - - - - - 5 - - - - 8.0

14 18 31 21 25 3 - - 23 55 39.5 18 29.5 1.5 4 8.5 17.5 10.0 - - - - - 6 - - - - 8.0

16 20 34 23 27 3 - - 26 55 41.0 18 31.0 1.5 4 8.5 17.5 10.0 - - - - - 6 - - - - 8.0

18 22 36 27 33 3 - - 28 55 44.0 20 32.5 2.0 5 9.0 19.5 11.5 15 7 - - - 6 - - - - 8.0

20 24 38 29 35 3 - - 30 60 44.0 20 32.5 2.0 5 9.0 19.5 11.5 15 7 - - - 6 - - - - 8.0

22 26 40 31 37 3 - - 31 60 44.0 20 32.5 2.0 5 9.0 19.5 11.5 15 7 - - - 6 - - - - 8.0

24 28 42 33 39 3 - - 35 60 44.0 20 32.5 2.0 5 9.0 19.5 11.5 15 7 - - - 6 - - - - 8.0

25 30 44 34 40 3 - - 37 60 45.0 20 33.5 2.0 5 9.0 19.5 11.5 15 7 - - - 6 - - - - 8.0

28 33 47 37 43 3 44.65 50.57 40 65 47.0 20 35.5 2.0 5 9.0 19.5 11.5 15 7 24.0 8.5 24 6 8 6.6 22.6 9 8.0

30 35 49 39 45 3 47.83 53.75 43 65 47.0 20 35.5 2.0 5 9.0 19.5 11.5 15 7 24.5 9.0 24 6 8 6.6 22.6 9 8.0

32 38 54 42 48 3 47.83 53.75 45 65 51.0 20 39.5 2.0 5 9.0 19.5 11.5 15 7 24.5 9.0 24 6 8 6.6 22.6 9 7.5

33 38 54 42 48 3 47.83 53.75 45 65 51.0 20 39.5 2.0 5 9.0 19.5 11.5 15 7 24.5 9.0 24 6 8 6.6 22.6 9 7.5

35 40 56 44 50 3 51.00 56.92 49 65 55.0 20 43.5 2.0 5 9.0 19.5 11.5 15 7 24.5 9.0 24 6 8 6.6 22.6 9 8.0

38 43 59 49 56 4 54.18 60.10 52 75 60.0 23 46.0 2.0 6 9.0 22.0 14.0 16 8 26.0 11.0 24 6 8 6.6 22.6 9 7.5

40 45 61 51 58 4 60.53 66.45 55 75 62.0 23 48.0 2.0 6 9.0 22.0 14.0 16 8 26.0 11.0 24 6 8 6.6 22.6 9 8.0

43 48 64 54 61 4 63.70 69.62 58 75 65.0 23 51.0 2.0 6 9.0 22.0 14.0 16 8 26.0 11.0 24 6 8 6.6 22.6 9 8.0

45 50 66 56 63 4 63.70 69.62 61 75 69.0 23 55.0 2.0 6 9.0 22.0 14.0 16 8 26.0 11.0 24 6 8 6.6 22.6 9 8.0

48 53 69 59 66 4 66.88 72.80 64 85 69.0 23 55.0 2.0 6 9.0 22.0 14.0 16 8 26.0 11.0 24 8 8 6.6 22.6 9 8.0

50 55 71 62 70 4 70.05 75.97 66 85 73.0 25 58.0 2.5 6 9.0 23.0 15.0 17 9.5 26.5 12.5 24 8 8 6.6 22.6 9 8.0

53 58 78 65 73 4 76.40 82.32 69 85 75.0 25 60.0 2.5 6 9.0 23.0 15.0 17 9.5 26.5 12.5 24 8 8 6.6 22.6 9 8.0

55 60 79 67 75 4 76.40 82.32 71 85 75.0 25 60.0 2.5 6 9.0 23.0 15.0 17 9.5 28.5 12.5 26 8 8 6.6 24.6 11 8.0

58 63 83 70 78 4 79.58 85.50 74 85 75.0 25 60.0 2.5 6 9.0 23.0 15.0 18 10.5 28.5 12.5 26 8 8 6.6 24.6 11 8.0

60 65 85 72 80 4 82.75 88.67 77 95 75.0 25 60.0 2.5 6 9.0 23.0 15.0 18 10.5 28.5 12.5 26 8 8 6.6 24.6 11 8.0

63 68 88 75 83 4 85.93 91.85 80 95 75.0 25 60.0 2.5 6 9.0 23.0 15.0 18 10.5 28.5 12.5 26 8 8 6.6 24.6 11 8.0

65 70 90 77 85 4 85.93 91.85 83 95 76.0 25 61.0 2.5 6 9.0 23.0 15.0 18 10.5 28.5 12.5 26 8 8 6.6 24.6 11 10.0

70 75 98 83 92 4 89.10 95.02 88 95 81.0 28 63.0 2.5 7 9.0 26.0 18.0 19 11.5 30.5 14.5 26 8 8 6.6 24.6 11 10.0

75 80 103 88 97 4 98.63 104.55 93 105 86.0 28 68.0 2.5 7 9.0 26.0 18.0 19 11.5 30.5 14.5 26 10 8 6.6 24.6 11 10.0

80 85 109 95 105 4 101.80 107.72 98 105 86.0 28 68.0 3.0 7 9.0 26.2 18.2 19 11.5 30.2 14.0 26 10 8 6.6 24.6 11 10.0

*) l1N acc. to EN 12756 is bigger

inch size available from size 0.375 to 3.125
Note: Additional technical & dimensional information will be provided on request.

50
 U700N Single Seals Standard Mechanical Seals - Pusher Seals

Product Description Technical Features

1. Single seal configuration 1. Versatile torque transmission available
2. Unbalanced design 2. Pumping screw for media with higher
3. Independent of direction of rotation viscosity also available
4. For plain shafts 3. Capable of self-cleaning
5. Multiple or wave springs rotary 4. Short installation length available on
construction request
6. Pumping device available for increased 5. Can be employed for low solids content
efficiency in circulation 6. Multifaceted application usage
7. Sealing with FEP & Spring energized
PTFE seals also available on request

l3 l8 Typical Industrial Applications Materials

f l9
Chemical industry Seal face: Special cast CrMo steel (S),
Food and beverage industry Silicon carbide (Q1, Q2), Aluminium oxide (V)
mx
Medias with low solid contents Seat G9: Carbon graphite antimony
Marine applications impregnated (A), Carbon graphite resin
Process industry impregnated (B), Silicon carbide (Q1*, Q2*)
Water and waste water technology
Seat G6: Silicon carbide (Q1*, Q2*)
Chemical standard pumps
(>100 = h8)

1.6 1.5 1.4 1.1 Seat G13: Carbon graphite antimony impregnated
2)

2 3
3)

Gear wheel feed pumps

H11

H8
H1
d1 h 6

(A), Carbon graphite resin impregnated (B)

Multistage pumps
d3

d7
d6

1.2 1.3 Secondary seals: EPDM (E), NBR (P),

Vertical screw pumps
FKM (V), FFKM (K)
Springs: CrNiMo steel (G) Metal parts:
Performance Capabilities
CrNiMo steel (G), Duplex (G1)
Sizes: d1 =Upto 100 mm (Upto 4.000’’) * Cannot be combined with seal face made of S
1) OO
2200

d8
1)

l5
Pressure: p1 = 25 bar (363 PSI)
l6
Temperature: t = –50 °C ... +220 °C Torque Transmissions
l1k l 7 +0.5
(–58 °F ... +428 °F)
Speed = 20 m/s (66 ft /s)
Note: The item numbers as depicted above are based on our technical experience and
knowledge and are placed in the chronological order of their assembly procedure. Permissible axial movement:
d1 = up to 25 mm: ± 1.0 mm d1 > 100 mm (4.000")
d1 = 28 up to 63 mm: ± 1.5 mm Torque transmission by
Item Part no. Description 4 set screws with cone
d1 = from 65 mm: ± 2.0 mm
1.1 472 Seal face points. Offset: 90°
1.2 485 Drive collar
1.3 474 Thrust ring Standards Drive key
1.4 412.1 O-ring EN 12756 (U700S2 / U740S2)
1.5 477 Spring
1.6 904 Set screw
2 475 Seat (G9)
3 412.2 O-ring
DIN 24250
1)
d1 > 100 mm: 30°
2)
d1 > 100 mm: +0.1
3) d1 > 100 mm: H7

Stationary Seats
l6 l6 l 16 l 16 l6
l5 l5 l 15 l 15 l5
20 O

30 O

30 O
R
20 O

20 O
R
+0.1

l28 l 14 l 19
l 13
d 11 +0.1

d 11 +0.1
d6 H11

H7
d 6 H11

d 12 H7
d 7 H8

d 6 H 11

l10
d 7 H8

d 7 H8

l 12 l 11 l 18
d 12

G9 G6 G4 G13 G16
(EN 1 2756) (EN 12756) (EN 12756, but l1 k is
shorter than specified)

51
 Design Variations
u

t
d s -0.05
(>100 -0.1)

d 24 min

b
0.5
U740 U700F U700S2
Dimensions, items and descriptions as for Shaft diameter d 1 =max. Upto100 mm Shaft diameter d1=max. Upto 100 mm
U700N, but with multiple springs (Item no. 1.5). (Upto 4.000”) Dimensions, items and (Upto 4.000”). Dimensions, items and
Preferably for d1>100 mm (4.000”). descriptions as for type U700N, but with descriptions as for type U700N, but with
pumping screw, dependent on direction of drive key. (without item no. 1.6)
U780N
rotation. (Viscosity ≤ISO VG10).
Shaft diameter: d1 = Upto 100 mm (Upto 4.000”)
Temperature: t = max. 180 oC (356 oF) U740F U740S2
Dimensions, items and description as for U700N. Shaft diameter d1= Upto 200 mm Shaft diameter:d1=Upto 200 mm
Design of the seal face especially for secondary
(Upto 7.875”) Dimensions, items and (Upto 7.875”) Dimensions, items and
sealing element made of PTFE (T).
Seal face: Carbon graphite antimony impregnated descriptions as for type U700N, but with descriptions as for type U700N, but with
(A), Carbon graphite resin impregnated (B), multiple springs and pumping screw, multiple springs and drive key.
Silicon carbide (Q1)* dependent on direction of rotation. (without item no.1.6)
Seat G9: CrMo cast steel (S)*, Silicon carbide (Q1) (Viscosity ≤ISO VG10).
* Cannot be combined with seal face made of
silicon carbide (Q1)

Dimensional Data
Dimensions in millimeter
d1 d3 d6 d7 d 8 d 11 d 12 d 24 ds l 1k l3 l5 l6 l7 l8 l9 l 10 l 11 l 12 l 13 l 14 l 15 l 16 l 18 l 19 l 28 b f m x u max. t R

14 25 21.0 25.0 3 20.5 24.6 16 34 35.0 25.0 1.5 4 8.5 17.5 10.0 7.5 10.0 6.5 7.6 5.6 1.2 3.8 - - 6.6 4 6 M5 10 1.5 1.2
16 27 23.0 27.0 3 22.0 28.0 18 36 35.0 25.0 1.5 4 8.5 17.5 10.0 7.5 11.5 8.5 9.0 7.5 1.2 3.8 - - 6.6 4 6 M5 10 1.5 1.5
18 33 27.0 33.0 3 24.0 30.0 20 38 37.5 26.0 2.0 5 9.0 19.5 11.5 8.5 12.5 9.0 10.0 8.0 1.5 5.0 15.0 7.0 7.5 5 7 M5 12 1.1 1.5
20 35 29.0 35.0 3 29.5 35.0 22 40 37.5 26.0 2.0 5 9.0 19.5 11.5 8.5 12.5 8.5 9.5 7.5 1.5 5.0 15.0 7.0 7.5 5 7 M5 12 1.1 1.5
22 37 31.0 37.0 3 29.5 35.0 24 42 37.5 26.0 2.0 5 9.0 19.5 11.5 8.5 12.5 8.5 9.5 7.5 1.5 5.0 15.0 7.0 7.5 6 7 M5 12 1.5 1.5
24 39 33.0 39.0 3 32.0 38.0 26 44 40.0 28.5 2.0 5 9.0 19.5 11.5 8.5 12.5 8.5 9.5 7.5 1.5 5.0 15.0 7.0 7.5 6 8 M5 12 1.5 1.5
25 40 34.0 40.0 3 32.0 38.0 27 45 40.0 28.5 2.0 5 9.0 19.5 11.5 8.5 12.5 8.5 9.5 7.5 1.5 5.0 15.0 7.0 7.5 6 8 M5 12 1.5 1.5
28 43 37.0 43.0 3 36.0 42.0 30 47 42.5 31.0 2.0 5 9.0 19.5 11.5 8.5 14.0 10.0 11.0 9.0 1.5 5.0 15.0 7.0 7.5 6 8 M6 13 1.5 1.5
30 45 39.0 45.0 3 39.2 45.0 32 49 42.5 31.0 2.0 5 9.0 19.5 11.5 8.5 14.0 11.5 11.0 10.5 1.5 5.0 15.0 7.0 7.5 6 8 M6 13 1.5 1.5
32 47 42.0 48.0 3 42.2 48.0 34 51 42.5 31.0 2.0 5 9.0 19.5 11.5 8.5 14.0 11.5 11.0 10.5 1.5 5.0 15.0 7.0 7.5 6 8 M6 13 1.5 1.5
33 48 42.0 48.0 3 44.2 50.0 35 51 42.5 31.0 2.0 5 9.0 19.5 11.5 8.5 14.5 12.0 11.5 10.5 1.5 5.0 15.0 7.0 7.5 6 8 M6 13 1.5 1.5
35 50 44.0 50.0 3 46.2 52.0 37 54 42.5 31.0 2.0 5 9.0 19.5 11.5 8.5 14.5 12.0 11.5 11.0 1.5 5.0 15.0 7.0 7.5 6 8 M6 13 1.5 1.5
38 55 49.0 56.0 4 49.2 55.0 40 59 45.0 31.0 2.0 6 9.0 22.0 14.0 10.0 14.5 11.3 11.5 10.3 1.5 5.0 16.0 8.0 9.0 6 8 M6 13 1.5 1.5
40 57 51.0 58.0 4 52.2 58.0 42 61 45.0 31.0 2.0 6 9.0 22.0 14.0 10.0 14.5 11.8 11.5 10.8 1.5 5.0 16.0 8.0 9.0 6 8 M6 13 1.5 1.5
43 60 54.0 61.0 4 53.3 62.0 45 65 45.0 31.0 2.0 6 9.0 22.0 14.0 10.0 17.0 13.2 14.3 12.0 2.0 6.0 16.0 8.0 9.0 6 8 M6 13 1.5 2.5
45 62 56.0 63.0 4 55.3 64.0 47 66 45.0 31.0 2.0 6 9.0 22.0 14.0 10.0 17.0 12.8 14.3 11.6 2.0 6.0 16.0 8.0 9.0 6 8 M6 13 1.5 2.5
48 65 59.0 66.0 4 59.7 68.4 50 69 45.0 31.0 2.0 6 9.0 22.0 14.0 10.0 17.0 12.8 14.3 11.6 2.0 6.0 16.0 8.0 9.0 6 8 M6 13 1.5 2.5
50 67 62.0 70.0 4 60.8 69.3 52 71 47.5 32.5 2.5 6 9.0 23.0 15.0 10.5 17.0 12.8 14.3 11.6 2.0 6.0 17.0 9.5 9.5 6 8 M6 13 1.5 2.5
53 70 65.0 73.0 4 63.8 72.3 55 75 47.5 32.5 2.5 6 9.0 23.0 15.0 12.0 17.0 13.5 14.3 12.3 2.0 6.0 17.0 9.5 11.0 6 8 M6 13 1.5 2.5
55 72 67.0 75.0 4 66.5 75.4 57 76 47.5 32.5 2.5 6 9.0 23.0 15.0 12.0 18.0 14.5 15.3 13.3 2.0 6.0 17.0 9.5 11.0 6 8 M6 13 1.5 2.5
58 79 70.0 78.0 4 69.5 78.4 60 83 52.5 37.5 2.5 6 9.0 23.0 15.0 12.0 18.0 14.5 15.3 13.3 2.0 6.0 18.0 10.5 11.0 8 9 M8 13 1.9 2.5
60 81 72.0 80.0 4 71.5 80.4 62 85 52.5 37.5 2.5 6 9.0 23.0 15.0 12.0 18.0 14.5 15.3 13.3 2.0 6.0 18.0 10.5 11.0 8 9 M8 13 1.9 2.5
63 84 75.0 83.0 4 74.5 83.4 65 88 52.5 37.5 2.5 6 9.0 23.0 15.0 12.0 18.0 14.2 15.3 13.3 2.0 6.0 18.0 10.5 11.0 8 9 M8 13 1.9 2.5
65 86 77.0 85.0 4 76.5 85.4 67 95 52.5 37.5 2.5 6 9.0 23.0 15.0 12.0 18.0 14.2 15.3 13.0 2.0 6.0 18.0 10.5 11.0 8 9 M8 13 1.9 2.5
68 89 81.0 90.0 4 82.7 91.5 70 93 52.5 34.5 2.5 7 9.0 26.0 18.0 12.5 19.0 14.9 16.0 13.7 2.0 6.0 18.5 11.0 11.3 8 9 M8 13 1.9 2.5
70 91 83.0 92.0 4 83.0 92.0 72 95 60.0 42.0 2.5 7 9.0 26.0 18.0 12.5 18.0 14.2 15.3 13.0 2.0 6.0 19.0 11.5 11.3 8 9 M8 16 1.9 2.5
75 99 88.0 97.0 4 90.2 99.0 77 105 60.0 42.0 2.5 7 9.0 26.0 18.0 12.5 18.0 15.2 15.3 14.0 2.0 6.0 19.0 11.5 11.3 8 10 M8 16 1.9 2.5
80 104 95.0 105.0 4 95.2 104.0 82 109 60.0 41.8 3.0 7 9.0 26.2 18.2 13.0 19.0 16.2 16.3 15.0 2.0 6.0 19.0 11.5 12.0 8 10 M8 16 1.9 2.5
85 109 100.0 110.0 4 100.2 109.0 87 114 60.0 41.8 3.0 7 9.0 26.2 18.2 15.0 19.0 16.0 16.3 14.8 2.0 6.0 19.0 11.5 14.0 8 10 M8 16 1.9 2.5
90 114 105.0 115.0 4 105.2 114.0 92 119 65.0 46.8 3.0 7 9.0 26.2 18.2 15.0 19.0 16.0 16.3 14.8 2.0 6.0 20.5 13.0 14.0 10 10 M8 20 2.3 2.5
95 119 110.0 120.0 4 111.6 120.3 97 124 65.0 47.8 3.0 7 9.0 25.2 17.2 15.0 20.0 17.0 17.3 15.8 2.0 6.0 20.5 13.0 14.0 10 10 M8 20 2.3 2.5
100 124 115.0 125.0 4 114.5 123.3 102 129 65.0 47.8 3.0 7 9.0 25.2 17.2 15.0 20.0 17.0 17.3 15.8 2.0 6.0 20.5 13.0 14.0 10 10 M8 20 2.3 2.5
105 138 122.2 134.3 5 - - 108 143 67.0 47.0 2.0 10 - 30.0 20.0 - - - - - - - - - - 10 10 M8 20 2.3 -
110 143 128.2 140.3 5 - - 113 148 67.0 47.0 2.0 10 - 30.0 20.0 - - - - - - - - - - 10 10 M8 20 2.3 -
115 148 136.2 148.3 5 - - 118 153 67.0 47.0 2.0 10 - 30.0 20.0 - - - - - - - - - - 10 10 M8 20 2.3 -
120 153 138.2 150.3 5 - - 123 158 67.0 47.0 2.0 10 - 30.0 20.0 - - - - - - - - - - 10 10 M8 20 2.3 -
125 158 142.2 154.3 5 - - 128 163 67.0 47.0 2.0 10 - 30.0 20.0 - - - - - - - - - - 10 10 M8 20 2.3 -
130 163 146.2 158.3 5 - - 133 168 67.0 47.0 2.0 10 - 30.0 20.0 - - - - - - - - - - 10 10 M8 20 2.3 -
135 168 152.2 164.3 5 - - 138 173 67.0 47.0 2.0 10 - 30.0 20.0 - - - - - - - - - - 10 10 M8 20 2.3 -
140 173 156.2 168.3 5 - - 143 178 67.0 47.0 2.0 10 - 30.0 20.0 - - - - - - - - - - 10 10 M8 20 2.3 -
145 178 161.2 173.3 5 - - 148 183 67.0 47.0 2.0 10 - 30.0 20.0 - - - - - - - - - - 10 10 M8 20 2.3 -
150 183 168.2 180.3 5 - - 153 188 69.0 47.0 2.0 10 - 32.0 22.0 - - - - - - - - - - 10 10 M8 20 2.3 -
155 191 173.2 185.3 5 - - 158 196 80.0 56.0 2.0 12 - 34.0 24.0 - - - - - - - - - - 12 12 M8 24 2.1 -
160 196 178.2 190.3 5 - - 163 201 80.0 56.0 2.0 12 - 34.0 24.0 - - - - - - - - - - 12 12 M8 24 2.1 -
165 201 183.2 195.3 5 - - 168 206 80.0 56.0 2.0 12 - 34.0 24.0 - - - - - - - - - - 12 12 M8 24 2.1 -
170 206 188.2 200.3 5 - - 173 211 80.0 56.0 2.0 12 - 34.0 24.0 - - - - - - - - - - 12 12 M8 24 2.1 -
175 211 193.2 205.3 5 - - 178 216 80.0 56.0 2.0 12 - 34.0 24.0 - - - - - - - - - - 12 12 M8 24 2.1 -
180 216 207.5 219.3 5 - - 183 221 84.0 56.0 2.0 12 - 38.0 28.0 - - - - - - - - - - 12 12 M8 24 2.1 -
185 221 212.5 224.3 5 - - 188 226 84.0 56.0 2.0 12 - 38.0 28.0 - - - - - - - - - 12 12 M8 24 2.1 -
190 226 217.5 229.3 5 - - 193 231 84.0 56.0 2.0 12 - 38.0 28.0 - - - - - - - - - 12 12 M8 24 2.1 -
195 231 222.5 234.3 5 - - 198 236 84.0 56.0 2.0 12 - 38.0 28.0 - - - - - - - - - 12 12 M8 24 2.1 -
200 236 227.5 239.3 5 - - 203 241 84.0 56.0 2.0 12 - 38.0 28.0 - - - - - - - - - 12 12 M8 24 2.1 -
d1 >200 on request
EN 12756
inch size also available from size 0.625 to 7.875
Note: Additional technical & dimensional information will be provided on request.
52
 U740-D Dual Seals Standard Mechanical Seals - Pusher Seals

Product Description Technical Features

1. Dual seal configuration 1. Versatile torque transmission available
2. Unbalanced design 2. Pumping screw for media with higher
3. Independent of direction of rotation viscosity also available
4. For plain shafts 3. Capable of self-cleaning
5. Multiple or wave springs rotary 4. Short installation length available on
construction request
6. Pumping device available for 5. Can be employed for low solids content
increased efficiency in circulation 6. Multifaceted application usage
(U740F-D) 7. EN 12756 (For connection dimensions
7. Sealing with FEP & Spring energized d1 upto 100 mm)
PTFE seals also available on request

l1 1) d1 > 100 mm: 30° Typical Industrial Applications

l7 +0.5 l3 2) d1 > 100 mm: +0.1 Adhesives
3) Chemical industry
d1 > 100 mm: H7
l9 l4 l31 Low solids content and low abrasive media
Media with poor lubrication properties
Process industry
mx 0
1) Toxic and hazardous media
20 Chemical standard pumps
Design Variations

0.5
(>100 = h8)

3 2 1.1 1.7 1.6 1.4 1.8 4 5

d7 H8 3)
d6 H11 2)

(>100 -0.1)
-0.05
d1 h6
d3

ds
1.5 1.3 1.2 l8

U740F-D
Dimensions, items and descriptions as for
d8 U740-D, but with pumping screw (Item no. 1.4).
l5 l6 5 Dependent on direction of rotation.
Note: The item numbers as depicted above are based on our technical experience and
knowledge and are placed in the chronological order of their assembly procedure.
Viscosity ≤ ISOVG10).

Performance Capabilities
Item Part no. Description Sizes: d1 = Upto 200 mm (Upto 7.875’’)
1.1 472.1 Seal face Pressure: p1 = 25 bar (363 PSI)
Standards Temperature: t = -50 °C ... + 220 °C
1.2 472.2 Seal face EN 12756 (-58 °F … + 428 °F)
1.3 474 Thrust ring Speed = 20 m/s (66 ft /s)
1.4 485 Drive collar Torque Transmissions Permissible axial movement:
1.5 477 Spring d1 upto 100 mm: ± 0.5 mm
d1 > 100 mm (4.000”)
1.6 904 Set screw d1 from 100 mm: ± 2.0 mm
Torque transmission by
1.7 412.1 O-ring 4 set screws with cone Materials
1.8 412.2 O-ring point. Offset: 90° Seal face: Special cast CrMo steel (S),
2 475.1 Seat (G9) Silicon carbide (Q1, Q2)
3 412.3 O-ring Seat G9 : Carbon graphite antimony
4 475.2 Seat (G9)
impregnated (A), Carbon graphite resin
Spring loaded drive impregnated (B), Silicon carbide (Q1*, Q2*)
5 412.4 O-ring pin
Seat G4 : Silicon carbide (Q1*, Q2*)
DIN 24250 (U740-D22)
Seat G6 : Silicon carbide (Q1*, Q2*)
t

Seat G13 : Carbon graphite antimony

d9 e8
impregnated (A), Carbon graphite resin
l35 impregnated (B)
* Cannot be combined with seal face made of S
53
 Stationary Seats

l6 l16 l16
l5 l15 l15

30 O

30 O
R

R
20 O

l 14 l13

d11 +0.1

d11 +0.1
l28

d12 H7

d12 H7
l 12 l11
l10 d 6 H11

d 7 H8

G6 G4 G13
(EN 12756)

Dimensional Data
Dimensions in millimeter
d1 d3 d6 d7 d8 d9 d 11 d 12 ds l1 l3 l4 l5 l6 l7 l8 l9 l 10 l 11 l 12 l 13 l 14 l 15 l 16 l 28 l 31 l 35 mx t R
18 33 27.0 33.0 3 4 24.0 30.0 - 61.0 38 19.0 2.0 5 9 19.5 11.5 8.5 12.5 9.0 10.0 8.0 1.5 5 7.5 17.0 15 M5 3.5 1.5
20 35 29.0 35.0 3 4 29.5 35.0 - 61.0 38 19.0 2.0 5 9 19.5 11.5 8.5 12.5 8.5 9.5 7.5 1.5 5 7.5 17.0 15 M5 3.5 1.5
22 37 31.0 37.0 3 4 29.5 35.0 42 61.0 38 19.0 2.0 5 9 19.5 11.5 8.5 12.5 8.5 9.5 7.5 1.5 5 7.5 17.0 15 M5 3.5 1.5
24 39 33.0 39.0 3 4 32.0 38.0 44 61.0 38 19.0 2.0 5 9 19.5 11.5 8.5 12.5 8.5 9.5 7.5 1.5 5 7.5 17.0 15 M5 3.5 1.5
25 40 34.0 40.0 3 4 32.0 38.0 45 61.0 38 19.0 2.0 5 9 19.5 11.5 8.5 12.5 8.5 9.5 7.5 1.5 5 7.5 17.0 15 M5 3.5 1.5
28 43 37.0 43.0 3 4 36.0 42.0 47 62.0 39 19.5 2.0 5 9 19.5 11.5 8.5 14.0 10.0 11.0 9.0 1.5 5 7.5 17.5 15 M6 3.5 1.5
30 45 39.0 45.0 3 4 39.2 45.0 49 62.0 39 19.5 2.0 5 9 19.5 11.5 8.5 14.0 11.5 11.0 10.5 1.5 5 7.5 17.5 15 M6 3.5 1.5
32 47 42.0 48.0 3 4 42.2 48.0 51 62.0 39 19.5 2.0 5 9 19.5 11.5 8.5 14.0 11.5 11.0 10.5 1.5 5 7.5 17.5 15 M6 3.5 1.5
33 48 42.0 48.0 3 4 44.2 50.0 51 62.0 39 19.5 2.0 5 9 19.5 11.5 8.5 14.5 12.0 11.5 10.5 1.5 5 7.5 17.5 15 M6 3.5 1.5
35 50 44.0 50.0 3 4 46.2 52.0 54 62.0 39 19.5 2.0 5 9 19.5 11.5 8.5 14.5 12.0 11.5 11.0 1.5 5 7.5 17.5 15 M6 3.5 1.5
38 55 49.0 56.0 4 4 49.2 55.0 59 69.0 41 20.5 2.0 6 9 22.0 14.0 10.0 14.5 11.3 11.5 10.3 1.5 5 9.0 18.5 15 M6 3.5 1.5
40 57 51.0 58.0 4 4 52.2 58.0 61 70.0 42 21.0 2.0 6 9 22.0 14.0 10.0 14.5 11.8 11.5 10.8 1.5 5 9.0 19.0 15 M6 3.5 1.5
43 60 54.0 61.0 4 4 53.3 62.0 65 70.0 42 21.0 2.0 6 9 22.0 14.0 10.0 17.0 13.2 14.3 12.0 2.0 6 9.0 19.0 15 M6 3.5 2.5
45 62 56.0 63.0 4 4 55.3 64.0 66 70.0 42 21.0 2.0 6 9 22.0 14.0 10.0 17.0 12.8 14.3 11.6 2.0 6 9.0 19.0 15 M6 3.5 2.5
48 65 59.0 66.0 4 4 59.7 68.4 69 70.0 42 21.0 2.0 6 9 22.0 14.0 10.0 17.0 12.8 14.3 11.6 2.0 6 9.0 19.0 15 M6 3.5 2.5
50 67 62.0 70.0 4 4 60.8 69.3 71 73.0 43 21.5 2.5 6 9 23.0 15.0 10.5 17.0 12.8 14.3 11.6 2.0 6 9.5 19.5 15 M6 3.5 2.5
53 70 65.0 73.0 4 4 63.8 72.3 75 73.0 43 21.5 2.5 6 9 23.0 15.0 12.0 17.0 13.5 14.3 12.3 2.0 6 11.0 19.5 15 M6 3.5 2.5
55 72 67.0 75.0 4 4 66.5 75.4 76 73.0 43 21.5 2.5 6 9 23.0 15.0 12.0 18.0 14.5 15.3 13.3 2.0 6 11.0 19.5 15 M8 3.5 2.5
58 79 70.0 78.0 4 5 69.5 78.4 83 86.0 56 28.0 2.5 6 9 23.0 15.0 12.0 18.0 14.5 15.3 13.3 2.0 6 11.0 23.5 19 M8 3.5 2.5
60 81 72.0 80.0 4 5 71.5 80.4 85 86.0 56 28.0 2.5 6 9 23.0 15.0 12.0 18.0 14.5 15.3 13.3 2.0 6 11.0 23.5 19 M8 3.5 2.5
63 84 75.0 83.0 4 5 74.5 83.4 88 85.0 55 27.5 2.5 6 9 23.0 15.0 12.0 18.0 14.2 15.3 13.3 2.0 6 11.0 24.5 19 M8 3.5 2.5
65 86 77.0 85.0 4 5 76.5 85.4 95 85.0 55 27.5 2.5 6 9 23.0 15.0 12.0 18.0 14.2 15.3 13.0 2.0 6 11.0 24.5 19 M8 3.5 2.5
68 89 81.0 90.0 4 5 82.7 91.5 93 91.0 55 27.5 2.5 7 9 26.0 18.0 12.5 19.0 14.9 16.0 13.7 2.0 6 11.3 24.5 19 M8 3.5 2.5
70 91 83.0 92.0 4 5 83.0 92.0 95 92.0 56 28.0 2.5 7 9 26.0 18.0 12.5 18.0 14.2 15.3 13.0 2.0 6 11.3 23.5 19 M8 3.5 2.5
75 99 88.0 97.0 4 5 90.2 99.0 105 92.0 56 28.0 2.5 7 9 26.0 18.0 12.5 18.0 15.2 15.3 14.0 2.0 6 11.3 25.5 19 M8 3.5 2.5
80 104 95.0 105.0 4 5 95.2 104.0 109 92.5 56 28.0 3.0 7 9 26.2 18.2 13.0 19.0 16.2 16.3 15.0 2.0 6 12.0 25.5 19 M8 3.5 2.5
85 109 100.0 110.0 4 5 100.2 109.0 114 92.5 56 28.0 3.0 7 9 26.2 18.2 15.0 19.0 16.0 16.3 14.8 2.0 6 14.0 25.0 19 M8 3.5 2.5
90 114 105.0 115.0 4 5 105.2 114.0 119 92.5 56 28.0 3.0 7 9 26.2 18.2 15.0 19.0 16.0 16.3 14.8 2.0 6 14.0 25.5 19 M8 3.5 2.5
95 119 110.0 120.0 4 5 111.6 120.3 124 90.5 56 28.0 3.0 7 9 25.2 17.2 15.0 20.0 17.0 17.3 15.8 2.0 6 14.0 25.0 19 M8 3.5 2.5
100 124 115.0 125.0 4 5 114.5 123.3 129 90.5 56 28.0 3.0 7 9 25.2 17.2 15.0 20.0 17.0 17.3 15.8 2.0 6 14.0 25.0 19 M8 3.5 2.5
105 138 122.2 134.3 5 7 - - 143 108.0 68 34.0 2.0 10 - 30.0 20.0 - - - - - - - - 30.5 22 M8 3.5 -
110 143 128.2 140.3 5 7 - - 148 110.0 70 35.0 2.0 10 - 30.0 20.0 - - - - - - - - 31.5 22 M8 3.5 -
115 148 136.2 148.3 5 7 - - 153 110.0 70 35.0 2.0 10 - 30.0 20.0 - - - - - - - - 31.5 22 M8 3.5 -
120 153 138.2 150.3 5 7 - - 158 110.0 70 35.0 2.0 10 - 30.0 20.0 - - - - - - - - 31.5 22 M8 3.5 -
125 158 142.2 154.3 5 7 - - 163 110.0 70 35.0 2.0 10 - 30.0 20.0 - - - - - - - - 31.5 22 M8 3.5 -
130 163 146.2 158.3 5 7 - - 168 110.0 70 35.0 2.0 10 - 30.0 20.0 - - - - - - - - 31.5 22 M8 3.5 -
135 168 152.2 164.3 5 7 - - 173 110.0 70 35.0 2.0 10 - 30.0 20.0 - - - - - - - - 31.5 22 M8 3.5 -
140 173 156.2 168.3 5 7 - - 178 110.0 70 35.0 2.0 10 - 30.0 20.0 - - - - - - - - 31.5 22 M8 3.5 -
145 178 161.2 173.3 5 7 - - 183 110.0 70 35.0 2.0 10 - 30.0 20.0 - - - - - - - - 31.5 22 M8 3.5 -
150 183 168.2 180.3 5 7 - - 188 114.0 70 35.0 2.0 10 - 32.0 22.0 - - - - - - - - 31.5 22 M8 3.5 -
155 191 173.2 185.3 5 7 - - 196 127.0 79 39.5 2.0 12 - 34.0 24.0 - - - - - - - - 35.5 22 M8 3.5 -
160 196 178.2 190.3 5 7 - - 201 127.0 79 39.5 2.0 12 - 34.0 24.0 - - - - - - - - 35.5 22 M8 3.5 -
165 201 183.2 195.3 5 7 - - 206 127.0 79 39.5 2.0 12 - 34.0 24.0 - - - - - - - - 35.5 22 M8 3.5 -
170 206 188.2 200.3 5 7 - - 211 127.0 79 39.5 2.0 12 - 34.0 24.0 - - - - - - - - 35.5 22 M8 3.5 -
175 211 193.2 205.3 5 7 - - 216 127.0 79 39.5 2.0 12 - 34.0 24.0 - - - - - - - - 35.5 22 M8 3.5 -
180 216 207.5 219.3 5 7 - - 221 135.0 79 39.5 2.0 12 - 38.0 28.0 - - - - - - - - 35.5 22 M8 3.5 -
185 221 212.5 224.3 5 7 - - 226 135.0 79 39.5 2.0 12 - 38.0 28.0 - - - - - - - - 35.5 22 M8 3.5 -
190 226 217.5 229.3 5 7 - - 231 135.0 79 39.5 2.0 12 - 38.0 28.0 - - - - - - - - 35.5 22 M8 3.5 -
195 231 222.5 234.3 5 7 - - 236 135.0 79 39.5 2.0 12 - 38.0 28.0 - - - - - - - - 35.5 22 M8 3.5 -
200 236 227.5 239.3 5 7 - - 241 135.0 79 39.5 2.0 12 - 38.0 28.0 - - - - - - - - 35.5 22 M8 3.5 -
d1 > 200 on request
inch size available from size 0.750 to 7.875
Note: Additional technical & dimensional information will be provided on request.

54
 U300N Single Seals Standard Mechanical Seals - Pusher Seals

Product Description Technical Features

1. Single seal configuration 1. Low cost seal solution
2. Unbalanced Design 2. No damage to the shaft
3. Dependent of direction of rotation 3. Short installation length available on
4. For plain shafts request
5. Torque transmission is through the 4. Can be employed for low solids content
conical spring

l8 Typical Industrial Applications

Chemical industry
b l5 l6
Food and beverage industry
Process industry
Water and waste water technology
Chemical standard pumps
Eccentric screw pumps
Submersible pumps

Materials
Seal face: Special cast CrMo steel (S)
Seat G9: Carbon graphite antimony
impregnated (A), Carbon graphite resin
1.4 1.3 1.2 1.1 2 3 impregnated (B)
d 6 H11
db min

d 7 H8
d1 h6
d3

Performance Capabilities
Sizes: d1 = Upto 80 mm (Upto 3.15’’)
Pressure: p1 = 10 bar (145 PSI)
Temperature: t = -20 °C ...+140 °C
(- 4 °F ...+284 °F)
Speed: = 15 m/s (50 ft /s)
20 O Permissible axial movement: ± 1.0 mm
d8
l 3 / l 21 3) l9 5
Standards
EN 12756
l1N l7 +0.5

Note: The item numbers as depicted above are based on our technical experience and
knowledge and are placed in the chronological order of their assembly procedure.

Stationary Seats
l6 l 16 l 16 l6

Item Part no. Description l5 l 15 l 15 l5

20 O

30 O

30 O
R

20 O
R

1.1 472 Seal face

1.2 412.1 O-ring l28 l 14 l 13 l9
H11

H8
d11 +0.1

H7

d 11+0.1
d 6 H11

H7

l8
d 7 H8

l 10 l 12 l 11
d 12

1.3 474 Thrust ring

d6

d7
d 12

1.4 478 Right hand spring

G6 (EN 12756) G4 G13 G9 (EN 12756)
1.4 479 Left hand spring
l6
2 475 Seat (G9) l5
20 O

3 412.2 O-ring
DIN 24250 l 19
d 6 H11

d 7 H8

l 18

G16 (EN 12756)

55
 Design Variations

l 22 l 23

d13

d13
U300 U320 U370G
Items and description as U300N. Items and descriptions as for type U300N, but with Items and descriptions as for type U300N, but with shrink
Seal face: Special cast CrMo steel (S) carbon graphite seal face shrink-fitted to the seal face fitted silicon carbide seal face to the seal face carrier
(Item no. 1.1).
Seat G13: Carbon graphite antimony impregnated carrier (Item no. 1.1). Shaft diameter: d1 = Upto 80 mm (Upto ... 3.15’’)
(A), Carbon graphite resin impregnated (B) Seal face: Carbon graphite antimony impregnated (A), Temperature: t = –20 °C ... +180 °C (–4 °F ... +355 °F)
Carbon graphite resin impregnated (B) Speed = 10 m/s (33 ft/s)
Seat G4 : special cast CrMo steel (S), Silicon carbide Seal face: Silicon carbide (Q12, Q22), Tungsten carbide
(Q1, Q2) (U22)
Seat G6 (U320N4): Special cast CrMo steel (S), Seat G 4 : Silicon carbide (Q1, Q2)
Seat G13: Carbon graphite antimony impregnated (A),
Silicon carbide (Q1, Q2) Carbon graphite resin impregnated (B)
Seat G9 (U320N): Silicon carbide (Q1, Q2) Seat G6 (U370GN4): Silicon carbide (Q1, Q2)
Seat G6 also available in A, B = G30 (longer Seat G9 (U370GN): Carbon graphite antimony
installation length than G6) impregnated (A), Carbon graphite resin impregnated (B),
Silicon carbide (Q1, Q2)
Seat G6 also available in A, B = G30 (longer installation
length than G6)
Dimensional Data
Dimensions in millimeter
d1 d3 d6 d7 d8 d11 1) d121) d13 db l 1N l 3 3) l5 l6 l7 l8 l9 l 10 l 11 l 12 l 13 l 14 l 15 l 16 l 18 l 19 l 213) l 22 l 23 l 28 b 2) R

6 14 - - - 11.5 16.0 16 8 - - - - - - - - 9.0 6.5 7.1 5.6 1.2 3.8 - - 10.5 11.9 - - - 1.2
8 18 - - - 15.5 19.2 18 11 - - - - - - - - 9.0 8.0 7.1 7.0 1.2 3.8 - - 15.5 16.9 - - - 1.2
10* 19 17 21 3 15.5 19.2 20 13 40 15.5 1.5 4 8.5 17.5 10.0 7.5 9.0 7.5 7.1 6.6 1.2 3.8 - - 15.5 16.9 - 6.6 (8) 1.2
12* 21 19 23 3 17.5 21.6 22 16 40 16.0 1.5 4 8.5 17.5 10.0 7.5 10.0 6.5 7.6 5.6 1.2 3.8 - - 15.5 17.4 - 6.6 (8) 1.2
14* 23 21 25 3 20.5 24.6 24 18 40 16.5 1.5 4 8.5 17.5 10.0 7.5 10.0 6.5 7.6 5.6 1.2 3.8 - - 15.5 17.4 16.5 6.6 (8) 1.2
15 24 - - - 20.5 24.6 25 19 - - - - - - - - 11.0 7.5 8.6 6.6 1.2 3.8 - - 15.5 17.4 - - - 1.2
16* 26 23 27 3 22.0 28.0 26 21 40 18.0 1.5 4 8.5 17.5 10.0 7.5 11.5 8.5 9.0 7.5 1.5 5.0 - - 17.5 19.5 16.5 6.6 (8) 1.5
18* 29 27 33 3 24.0 30.0 31 23 45 19.5 2.0 5 9.0 19.5 11.5 8.5 12.5 9.0 10.0 8.0 1.5 5.0 15 7 18.5 20.5 18.0 7.5 (8) 1.5
20* 31 29 35 3 29.5 35.0 34 26 45 22.0 2.0 5 9.0 19.5 11.5 8.5 12.5 8.5 9.5 7.5 1.5 5.0 15 7 20.0 22.0 19.0 7.5 (8) 1.5
22* 33 31 37 3 29.5 35.0 36 28 45 21.5 2.0 5 9.0 19.5 11.5 8.5 12.5 8.5 9.5 7.5 1.5 5.0 15 7 21.5 23.5 20.5 7.5 (8) 1.5
24* 35 33 39 3 32.0 38.0 38 30 50 23.5 2.0 5 9.0 19.5 11.5 8.5 12.5 8.5 9.5 7.5 1.5 5.0 15 7 23.0 25.0 22.0 7.5 (8) 1.5
25* 36 34 40 3 32.0 38.0 39 31 50 26.5 2.0 5 9.0 19.5 11.5 8.5 12.5 8.5 9.5 7.5 1.5 5.0 15 7 24.5 26.5 23.5 7.5 (8) 1.5
26 37 - - - 34.0 40.0 40 32 - - - - 9.0 - - - 13.0 9.0 10.0 8.0 1.5 5.0 - - 24.5 26.5 23.5 - - 1.5
28* 40 37 43 3 36.0 42.0 42 35 50 26.5 2.0 5 9.0 19.5 11.5 8.5 14.0 10.0 11.0 9.0 1.5 5.0 15 7 24.5 26.5 24.5 7.5 (8) 1.5
30* 43 39 45 3 39.2 45.0 44 37 50 26.5 2.0 5 9.0 19.5 11.5 8.5 14.0 11.5 11.0 10.5 1.5 5.0 15 7 24.5 25.0 24.5 7.5 (8) 1.5
32* 46 42 48 3 42.2 48.0 46 39 55 28.5 2.0 5 9.0 19.5 11.5 8.5 14.0 11.5 11.0 10.5 1.5 5.0 15 7 28.0 28.5 28.0 7.5 (8) 1.5
33* 47 42 48 3 - - 47 40 55 28.5 2.0 5 9.0 19.5 11.5 8.5 - 12.0 - - - - 15 7 - - - 7.5 (8) 1.5
35* 49 44 50 3 46.2 52.0 49 43 55 28.5 2.0 5 9.0 19.5 11.5 8.5 14.5 12.0 11.5 11.0 1.5 5.0 15 7 28.0 28.5 28.0 7.5 (8) 1.5
38* 53 49 56 4 49.2 55.0 54 45 55 33.5 2.0 6 9.0 22.0 14.0 10.0 14.5 11.3 11.5 10.3 1.5 5.0 16 8 31.0 32.2 31.0 9.0 7.5 1.5
40* 56 51 58 4 52.2 58.0 56 49 55 36.0 2.0 6 9.0 22.0 14.0 10.0 14.5 11.8 11.5 10.8 1.5 5.0 16 8 34.0 34.7 34.0 9.0 (8) 1.5
42 59 - - - 53.3 62.0 58 52 - - - - 9.0 - - - 17.0 13.2 14.3 12.0 2.0 6.0 - - 35.0 37.3 35.0 - - 2.5
43* 59 54 61 4 - - 59 52 60 38.5 2.0 6 9.0 22.0 14.0 10.0 - 13.2 - - 2.0 - 16 8 - - - 9.0 7.5 2.5
45* 61 56 63 4 55.3 64.0 61 55 60 39.5 2.0 6 9.0 22.0 14.0 10.0 17.0 12.8 14.3 11.6 2.0 6.0 16 8 36.5 39.2 36.5 9.0 (8) 2.5
48* 64 59 66 4 59.7 68.4 64 58 60 46.0 2.0 6 9.0 22.0 14.0 10.0 17.0 12.8 14.3 11.6 2.0 6.0 16 8 42.0 44.7 42.0 9.0 (8) 2.5
50* 66 62 70 4 60.8 69.3 66 61 60 45.0 2.5 6 9.0 23.0 15.0 10.5 17.0 12.8 14.3 11.6 2.0 6.0 17 9.5 43.0 45.7 43.0 9.5 (8) 2.5
53* 69 65 73 4 - - 69 64 70 47.0 2.5 6 9.0 23.0 15.0 12.0 - 13.5 - - - - 17 9.5 - - - 11.0 8 2.5
55* 71 67 75 4 66.5 75.4 71 66 70 49.0 2.5 6 9.0 23.0 15.0 12.0 18.0 14.5 15.3 13.3 2.0 6.0 17 9.5 47.0 49.0 47.0 11.0 (8) 2.5
58* 76 70 78 4 69.5 78.4 78 69 70 55.0 2.5 6 9.0 23.0 15.0 12.0 18.0 14.5 15.3 13.3 2.0 6.0 18 10.5 50.0 52.0 50.0 11.0 (8) 2.5
60* 78 72 80 4 71.5 80.4 79 71 70 55.0 2.5 6 9.0 23.0 15.0 12.0 18.0 14.5 15.3 13.3 2.0 6.0 18 10.5 51.0 55.0 51.0 11.0 (8) 2.5
63* 83 75 83 4 - - 83 74 70 55.0 2.5 6 9.0 23.0 15.0 12.0 - 14.2 - - - - 18 10.5 - - - 11.0 (8) 2.5
65* 84 77 85 4 76.5 85.4 85 77 80 55.0 2.5 6 9.0 23.0 15.0 12.0 18.0 14.2 15.3 13.0 2.0 6.0 18 10.5 52.0 54.3 52.0 11.0 (8) 2.5
68* 88 81 90 4 82.7 91.5 88 80 80 55.0 2.5 7 9.0 26.0 18.0 12.5 19.0 14.9 16.0 13.7 2.0 6.0 18.5 11.0 53.0 55.3 52.7 11.3 (8) 2.5
70* 90 83 92 4 83.0 92.0 90 83 80 57.0 2.5 7 9.0 26.0 18.0 12.5 18.0 14.2 15.3 13.0 2.0 6.0 19 11.5 54.0 56.3 54.0 11.3 (10) 2.5
75* 98 88 97 4 90.2 99.0 98 88 80 62.0 2.5 7 9.0 26.0 18.0 12.5 18.0 15.2 15.3 14.0 2.0 6.0 19 11.5 55.0 56.3 54.0 11.3 (10) 2.5
80* 100 95 105 4 95.2 104.0 103 93 90 61.8 3.0 7 9.0 26.2 18.2 13.0 19.0 16.2 16.3 15.0 2.0 6.0 19 11.5 58.0 59.3 58.0 12.0 10 2.5
1) Fitting dimensions d 11 and d 12 only apply to type U370G with d 1 > 16mm
2) Dimensions in brackets lie either above or below l 1N
3) l 3 valid for U3....N, l 21 valid for U300
*) According to EN 12756
inch size also available from size 0.375 to 3.125
Note: Additional technical & dimensional information will be provided on request. 56
 U200N Single Seals Standard Mechanical Seals - Pusher Seals

Product Description Technical Features

1. Single seal configuration 1. Low cost seal solution
2. Unbalanced Design 2. No damage to the shaft
3. Dependent of direction of rotation 3. Short installation length available on
4. For plain shafts request
5. Torque transmission is through the
conical spring

l8
b l5 l6

1.4 1.3 1.2 1.1 2 3

d 6 H11

d 7 H8
d b min

d1 h 6
d3

20 O
d8

/
l3 l21 1) l9 5
l1N l7 +0.5

Item Part no. Description

Note: The item numbers as depicted above are based on our technical experience and
knowledge and are placed in the chronological order of their assembly procedure. 1.1 472 Seal face
1.2 412.1 O-ring
1.3 474 Thrust ring
1.4 478 Right hand spring
1.4 479 Left hand spring
2 475 Seat (G9)
3 412.2 O-ring
DIN 24250
57
 Performance Capabilities Typical Industrial Applications Standards
Shaft diameter: d1 = Upto 38 mm (Upto 1.500’’) Chemical industry EN 12756
Pressure: p1 = 10 bar (145 PSI) Food and beverage industry
Food processing Notes
Temperature: t = -20 °C ... +140 °C
(- 4 °F ... +284 °F) Pulp and paper industry Seal face: Carbon graphite resin impregnated (B)
Speed = 15 m/s (50 ft /s) Water and waste water technology Seat G9 : Silicon carbide (Q1, Q2),
Permissible axial movement: ±1.0 mm Special cast CrMo steel (S), Aluminium oxide (V)

Stationary Seats
l 16 l6 l6
l 15 l5 l5

30 O

20 O
R

20 O
l 14 l28 l19

H11
d 11 +0.1

H8
d 12 H7
l18

d 6 H11
l 10

d 7 H8
l 12

d6

d7
G6 G16
G4 (EN 12756) (EN 12756)
Design Variations
U200
Rotating unit U200 with seat G4 or G16 (shorter installation length).
Seal face: Carbon graphite resin impregnated (B)
Seat G 4 : Silicon carbide (Q1), Special cast CrMo steel (S)
Seat G16 : Silicon carbide (Q1, Q2), Special cast CrMo steel (S), Aluminium oxide (V)
U200N4
Rotating unit U200 with seat G6.
Seal face: Carbon graphite resin impregnated (B)
Seat G6: Silicon carbide (Q1), Special cast CrMo steel (S)

d1 d3 d6 d7 d8 d11 d12 db l 1N l 31) l5 l6 l7 l8 l9 l 10 l 12 l 14 l 15 l 16 l 18 l 19 l 211) l 28 b R

6 15 - - - 11.8 16.0 8 - - - - - - - - 6.5 5.6 1.2 3.8 - - 10.9 - - 1.2

8 18 - - - 15.5 19.2 11 - - - - - - - - 8.0 7.0 1.2 3.8 - - 15.5 - - 1.2
10 20 17 21 3 15.5 19.2 13 40 17.5 1.5 4 8.5 17.5 10.0 7.5 7.5 6.6 1.2 3.8 - - 15.9 6.6 8 1.2
12 22 19 23 3 17.5 21.6 16 40 17.5 1.5 4 8.5 17.5 10.0 7.5 8.0 7.0 1.2 3.8 - - 16.0 6.6 8 1.2
14 25 21 25 3 20.5 24.6 18 40 17.5 1.5 4 8.5 17.5 10.0 7.5 8.0 7.0 1.2 3.8 - - 16.0 6.6 8 1.2
15 27 - - - 20.5 24.6 19 - - - - - - - - 7.5 6.6 1.2 3.8 - - 17.4 - - 1.2
16 27 23 27 3 22.0 28.0 21 40 19.5 1.5 4 8.5 17.5 10.0 7.5 8.5 7.5 1.5 5.0 - - 19.0 6.6 8 1.5
18 30 27 33 3 24.0 30.0 23 45 20.5 2.0 5 9.0 19.5 11.5 8.5 9.0 8.0 1.5 5.0 15 7 20.5 7.5 8 1.5
20 32 29 35 3 29.5 35.0 26 45 22 2.0 5 9.0 19.5 11.5 8.5 8.5 7.5 1.5 5.0 15 7 22.0 7.5 8 1.5
22 35 31 37 3 29.5 35.0 28 45 23.5 2.0 5 9.0 19.5 11.5 8.5 8.5 7.5 1.5 5.0 15 7 23.5 7.5 8 1.5
24 38 33 39 3 32.0 38.0 30 50 25 2.0 5 9.0 19.5 11.5 8.5 8.5 7.5 1.5 5.0 15 7 25.0 7.5 8 1.5
25 40 34 40 3 32.0 38.0 31 50 26.5 2.0 5 9.0 19.5 11.5 8.5 8.5 7.5 1.5 5.0 15 7 26.5 7.5 8 1.5
26 41 - - - 34.0 40.0 32 - - - - - - - - 9.0 8.0 1.5 5.0 - - 26.5 - - 1.5
28 43 37 43 3 36.0 42.0 35 50 26.5 2.0 5 9.0 19.5 11.5 8.5 10.0 9.0 1.5 5.0 15 7 26.5 7.5 8 1.5
30 47 - - - 39.2 45.0 37 - - - - - - 11.5 - 11.5 10.5 1.5 5.0 15 7 25.0 - - 1.5
32 48 - - - 42.2 48.0 39 - - - - - - 11.5 - 13.0 10.5 1.5 5.0 15 7 28.5 - - 1.5
35 53 - - - 46.2 52.0 43 - - - - - - 11.5 - 13.5 11.0 1.5 5.0 15 7 28.5 - - 1.5
38 56 - - - 49.2 55.0 47 - - - - - - 14.0 - 13.0 10.3 1.5 5.0 16 8 32.0 - - 1.5
1) l 3 valid for U200N, l 21 valid for U200
According to EN 12756
inch sizes also available from size 0.250 to 1.500
Note: Additional technical & dimensional information will be provided on request.

58
 UG943 Single Seals Standard Mechanical Seals - Elastomer Bellows Seals

Product Description Technical Features

1. Single seal configuration 1. Low cost seal solution
2. Unbalanced design 2. Suitable for mild sterile applications
3. Independent of direction of rotation 3. No damage to the shaft
4. For plain shafts 4. Can be employed for low solids content
5. Rotary elastomer bellows design 5. Multifaceted application usage

1 Typical Industrial Applications

Food and beverage industry Cooling fluids
Multi-stage pumps (non-drive side) Circulating pumps
Media with low solids content Oil applications
Pressure oils for bio diesel fuels
Water and waste water technology Chemical industry
Water and waste water pumps Submersible pumps
Performance Capabilities
Shaft diameter: d1 = 10 … 100 mm (0.375" … 4")
Pressure: p1 = 12 bar (174 PSI),
1.6 2 1.4 1.1 3 4 vacuum up to 0.5 bar (7.25 PSI), up to 1 bar (14.5 PSI)
with seat locking
0.05

Temperature: t = -20 °C … +140 °C (-4 °F … +284 °F)

d14
d3

d1

Speed = 10 m/s (33 ft/s)

d16

Axial movement: ± 0.5 mm

1.2 1.3 1.5 Notes

A modular principle comprising a bellows unit for each
shaft diameter and a corresponding cylindrical spring for
individual length compensation to l1 installation length.
UG943 can also be used as a multiple seal in tandem or
in a back-to-back arrangement.
The entire UG943 series is available in metric
and inch sizes.
Standards
Note: The item numbers as depicted above are based on our technical experience and
knowledge and are placed in the chronological order of their assembly procedure. EN 12756
FDA
Materials
Seal face: Carbon graphite antimony impregnated (A),
Carbon graphite resin impregnated (B), Silicon carbide (Q1)
Item Description Seat: Silicon carbide (Q1, Q2), Aluminium oxide (V)
1.1 Seal face Elastomer: NBR (P), EPDM (E), FKM (V), HNBR (X4)
Metal parts: CrNiMo steel (G)
1.2 Bellows
1.3 Driver collar
Stationary Seats
1.4 “L” ring (spring collar)
l17
l61 l6
1.5 Washer l51 l5
R1

30 O

1.6 Corner Ring

20 O

2 Spring
d 71 ± 0.002"

3 Seat
d16 ± 0.05

l29 l41 l28

H11

4 O-ring
H8
d14

d 61

d6
d7

DIN 24250
G50 G55 G60
Euro standard US standard EN 12756

59
 Dimensional Data
Dimensions in inch
d1 d3 d6 d7 d14 d16 d 61 d 71 l1 l5 l6 l 17 l 28 l 29 l41 l 51 l 61

0.375 0.787 0.669 0.827 0.433 0.969 0.625 0.875 0.941 0.059 0.157 0.295 0.260 0.354 0.313 0.050 0.250
0.500 0.866 0.748 0.906 0.531 1.094 0.750 1.000 0.941 0.059 0.157 0.295 0.260 0.354 0.313 0.050 0.250
0.625 1.024 0.906 1.063 0.669 1.219 0.937 1.250 1.039 0.059 0.157 0.354 0.260 0.413 0.406 0.050 0.344
0.750 1.339 1.142 1.378 0.846 1.406 1.062 1.375 1.083 0.079 0.197 0.354 0.295 0.413 0.406 0.050 0.344
0.875 1.417 1.220 1.457 0.906 1.469 1.187 1.500 1.083 0.079 0.197 0.354 0.295 0.413 0.406 0.050 0.344
1.000 1.535 1.339 1.575 1.043 1.594 1.312 1.625 1.181 0.079 0.197 0.354 0.295 0.413 0.437 0.050 0.375
1.125 1.654 1.457 1.693 1.161 1.876 1.437 1.750 1.280 0.079 0.197 0.413 0.295 0.472 0.437 0.050 0.375
1.250 1.811 1.654 1.890 1.280 2.000 1.563 1.875 1.280 0.079 0.197 0.413 0.295 0.472 0.437 0.050 0.375
1.375 1.929 1.732 1.969 1.437 2.126 1.687 2.000 1.280 0.079 0.197 0.413 0.295 0.472 0.437 0.050 0.375
1.500 2.126 1.929 2.205 1.555 2.250 1.813 2.125 1.339 0.079 0.236 0.413 0.354 0.472 0.437 0.050 0.375
1.625 2.205 2.008 2.283 1.673 2.376 2.000 2.375 1.339 0.079 0.236 0.413 0.354 0.472 0.500 0.050 0.437
1.750 2.402 2.205 2.480 1.811 2.500 2.125 2.500 1.339 0.079 0.236 0.413 0.354 0.472 0.500 0.050 0.437
1.875 2.520 2.323 2.598 1.929 2.626 2.250 2.625 1.339 0.079 0.236 0.413 0.354 0.472 0.500 0.050 0.437
2.000 2.598 2.441 2.756 2.047 2.750 2.375 2.750 1.358 0.098 0.236 0.472 0.374 0.531 0.500 0.050 0.437
2.125 2.717 2.559 2.874 2.185 2.876 2.375 3.000 1.358 0.098 0.236 0.472 0.433 0.531 0.562 0.050 0.500
2.250 3.071 2.756 3.071 2.421 3.126 2.437 3.125 1.555 0.098 0.236 0.472 0.433 0.531 0.562 0.050 0.500
2.375 3.150 2.835 3.150 2.421 3.126 2.563 3.250 1.555 0.098 0.236 0.472 0.433 0.531 0.562 0.050 0.500
2.500 3.268 2.953 3.268 2.559 3.250 2.687 3.375 1.465 0.098 0.236 0.472 0.433 0.531 0.562 0.050 0.500
2.625 3.465 3.189 3.543 2.795 3.750 2.812 3.375 1.465 0.098 0.276 0.571 0.445 0.630 0.625 0.100 0.562
2.750 3.543 3.268 3.622 2.795 3.750 2.937 3.500 1.760 0.098 0.276 0.571 0.445 0.630 0.625 0.100 0.562
2.875 - - - - - 3.062 3.750 1.760 - - - - - 0.625 0.100 0.562
3.000 3.898 3.465 3.819 3.051 4.000 3.187 3.875 1.760 0.098 0.276 0.571 0.445 0.630 0.625 0.100 0.562
3.125 4.094 3.740 4.134 3.307 4.500 3.312 4.000 1.744 0.118 0.276 0.728 0.472 0.787 0.781 0.100 0.656
3.250 - - - - - 3.437 4.125 1.744 - - - - - 0.781 0.100 0.656
3.375 4.291 3.937 4.331 3.425 4.626 3.562 4.250 1.744 0.118 0.276 0.728 0.551 0.787 0.781 0.100 0.656
3.500 4.488 4.134 4.528 3.681 4.876 3.687 4.375 1.941 0.118 0.276 0.728 0.551 0.787 0.781 0.100 0.656
3.625 - - - - - 3.812 4.500 1.941 - - - - - 0.781 0.100 0.656
3.750 4.685 4.331 4.724 3.799 5.000 3.937 4.625 1.941 0.118 0.276 0.728 0.551 0.787 0.781 0.100 0.656
3.875 - - - - - 4.062 4.750 1.941 - - - - - 0.781 0.100 0.656
4.000 4.882 4.528 4.921 4.055 5.250 4.187 4.875 1.941 0.118 0.276 0.728 0.551 0.787 0.781 0.100 0.656

Dimensions in millimeter
d1 d3 d6 d7 d14 d16 d 61 d 71 l1 l5 l6 l17 l28 l29 l41 l51 l61

10 20 17 21 11.0 24.60 15.88 22.23 23.9 1.5 4 7.5 6.6 9.0 7.95 1.27 6.35
12 22 19 23 13.5 27.80 19.05 25.40 23.9 1.5 4 7.5 6.6 9.0 7.95 1.27 6.35
14 24 21 25 17.0 30.95 - - 26.4 1.5 4 9.0 6.6 10.5 - - -
15 - - - 17.0 30.95 - - - - - 9.0 - 10.5 - - -
16 26 23 27 17.0 30.95 23.80 31.75 26.4 1.5 4 9.0 6.6 10.5 10.31 1.27 8.74
18 32 27 33 20.0 34.15 - - 27.5 2.0 5 9.0 7.5 10.5 - - -
20 34 29 35 21.5 35.70 26.97 34.93 27.5 2.0 5 9.0 7.5 10.5 10.31 1.27 8.74
22 36 31 37 23.0 37.30 30.15 38.10 27.5 2.0 5 9.0 7.5 10.5 10.31 1.27 8.74
24 38 33 39 26.5 40.50 - - 30.0 2.0 5 9.0 7.5 10.5 - - -
25 39 34 40 26.5 40.50 33.32 41.28 30.0 2.0 5 9.0 7.5 10.5 11.10 1.27 9.53
28 42 37 43 29.5 47.65 36.50 44.45 32.5 2.0 5 10.5 7.5 12.0 11.10 1.27 9.53
30 44 39 45 32.5 50.80 - - 32.5 2.0 5 10.5 7.5 12.0 - - -
32 46 42 48 32.5 50.80 39.70 47.63 32.5 2.0 5 10.5 7.5 12.0 11.10 1.27 9.53
33 47 42 48 36.5 54.00 39.70 47.63 32.5 2.0 5 10.5 7.5 12.0 11.10 1.27 9.53
35 49 44 50 36.5 54.00 42.85 50.80 32.5 2.0 5 10.5 7.5 12.0 11.10 1.27 9.53
38 54 49 56 39.5 57.15 46.05 53.98 34.0 2.0 6 10.5 9.0 12.0 11.10 1.27 9.53
40 56 51 58 42.5 60.35 50.80 60.33 34.0 2.0 6 10.5 9.0 12.0 12.70 1.27 11.10
43 59 54 61 46.0 63.50 - - 34.0 2.0 6 10.5 9.0 12.0 - - -
45 61 56 63 46.0 63.50 53.98 63.50 34.0 2.0 6 10.5 9.0 12.0 12.70 1.27 11.10
48 64 59 66 49.0 66.70 57.15 66.68 34.0 2.0 6 10.5 9.0 12.0 12.70 1.27 11.10
50 66 62 70 52.0 69.85 60.33 69.85 34.5 2.5 6 12.0 9.5 13.5 12.70 1.27 11.10
53 69 65 73 55.5 73.05 60.33 76.20 34.5 2.5 6 12.0 11.0 13.5 14.27 1.27 12.70
55 71 67 75 58.5 76.20 - - 34.5 2.5 6 12.0 11.0 13.5 - - -
58 78 70 78 61.5 79.40 61.90 79.38 39.5 2.5 6 12.0 11.0 13.5 14.27 1.27 12.70
60 80 72 80 61.5 79.40 65.10 82.55 39.5 2.5 6 12.0 11.0 13.5 14.27 1.27 12.70
63 83 75 83 65.0 82.55 68.25 85.73 39.5 2.5 6 12.0 11.0 13.5 14.27 1.27 12.70
65 85 77 85 68.0 92.10 - - 39.5 2.5 6 14.5 11.0 16.0 - - -
68 88 81 90 71.0 95.25 71.42 85.73 37.2 2.5 7 14.5 11.3 16.0 15.88 2.54 14.27
70 90 83 92 71.0 95.25 74.60 88.90 44.7 2.5 7 14.5 11.3 16.0 15.88 2.54 14.27
75 99 88 97 77.5 101.60 80.95 98.43 44.7 2.5 7 14.5 11.3 16.0 15.88 2.54 14.27
80 104 95 105 84.0 114.30 84.12 101.60 44.3 3.0 7 18.5 12.0 20.0 19.84 2.54 16.66
85 109 100 110 87.0 117.50 90.47 107.95 44.3 3.0 7 18.5 14.0 20.0 19.84 2.54 16.66
90 114 105 115 93.5 123.85 93.65 111.13 49.3 3.0 7 18.5 14.0 20.0 19.84 2.54 16.66
95 119 110 120 96.5 127.00 100.00 117.48 49.3 3.0 7 18.5 14.0 20.0 19.84 2.54 16.66
100 124 115 125 103.0 133.35 106.35 123.83 49.3 3.0 7 18.5 14.0 20.0 19.84 2.54 16.66
Note: Additional technical & dimensional information will be provided on request

60
 UG100 Single Seals Standard Mechanical Seals - Elastomer Bellows Seals

Product Description Technical Features

1. Single seal configuration 1. Low cost seal solution
2. Unbalanced design 2. Suitable for mild sterile applications
3. Independent of direction of rotation 3. No damage to the shaft
4. For plain shafts 4. Can be employed for low solids content
5. Rotary elastomer bellows design 5. Multifaceted application usage

Typical Industrial Applications

Chemical industry
Food processing industry
Pulp, paper & Latex
Water, waste water and mild slurries
Chemical standard pumps
Helical screw pumps
Submersible pumps
Performance Capabilities
Sizes: d1 = Up to 100 mm (Up to 4.000’’)
Pressure: p1 = 16 bar (230 PSI)
vacuum: 0.5 bar (7.25 PSI), up to 1 bar (14.5
1.2 1.5 1.1 2 3 PSI) with seat locking
dST min

Temperature: t = -20°C...+140°C (-4°F...+284°F)

d1 h8
min
da

d3

Speed: = 10 m/s (33 ft/s)

db

Permissible axial movement: ±2.0 mm

1.3 1.4 Notes
The UG100 can also be used as a multiple seal in
tandem or in a back-to-back arrangement.
Installation proposals can be supplied on
request.
Dimension adaptations for specific conditions,
e.g. shaft in inches or special seat dimensions are
available on request.
Standards
EN 12756
Note: The item numbers as depicted above are based on our technical experience and
knowledge and are placed in the chronological order of their assembly procedure. Materials
Seal face: Carbon graphite antimony
impregnated (A), Carbon graphite resin
Item Part no. Description Item Part no. Description impregnated (B), Silicon carbide (Q1),
Tungsten carbide (U3)
1.1 472 Seal face 1.5 477 Spring Seat: Silicon carbide (Q1, Q2), Tungsten
carbide (U3), Special cast CrMo steel (S),
1.2 481 Bellows 2 475 Seat Aluminium oxide (V)
1.3 484.2 L-ring (spring collar) 3 412 O-ring or cup rubber Elastomer: NBR (P), EPDM (E), FKM (V),
1.4 484.1 L-ring (spring collar) Metal parts: CrNiMo steel (G), Hastelloy®
DIN 24250 C-4 (M)
DIN 24250
Stationary Seats
l16 l7 +0.5 l6 l6 l17
O

l6
20

l15 l5 l5
20 O

R1
30 O

l5
R

5
20 O

l14 l9 d8 l28
H11

d16 -+ 0.05
H11
d 11 +0.1

H8
d 12 H7

H8

l12 l8 l10 l28 l29

H11
d6
d7

H8
d6
d7

d14
d6
d7

G9 G6
G4 G60 G50
EN 12756 EN 12756
EN 12756 Euro standard
61
 Design Variations

l1 l2 l3
ds min

dm min
ds min
l1k l1N l1S

UG120 UG130 UG100S20

Dimensions, items and designations same as for Dimensions, items and designations same as for Dimensions, items and designations same as for
UG100, but with an extended bellows tail to achieve the UG100, but with an extended bellows tail to achieve the UG100, but with an extended bellows tail to
fitting length I1k according to EN 12756 in combination fitting length I1N according to EN 12756 in combination achieve the special fitting length I 1 S in
with seat G6 or G60 (da exceeds EN 12756). with seat G6 or G60 (d8 exceeds EN 12756). combination with seat G50.

Dimensional Data
Dimensions in millimeter

d1 d3 d 6 d 7 d 8 d 11 d 12 d 14 d 16 da d b*) d m*) d s*) d ST l l1 l 1k l 1N l 1S l2 l3 l5 l6 l7 l8 l9 l 10 l 12 l 14 l 15 l 16 l 17 l 28 l 29 R

10 15.7 17 21 3 15.5 19.2 11.0 24.60 22.5 20.5 18 18 24 14.5 25.9 32.5 40 34.0 33.4 25 1.5 4 8.5 17.5 10.0 7.5 7.5 6.6 1.2 3.8 7.5 6.6 9.0 1.2
12 17.7 19 23 3 17.5 21.6 13.5 27.80 25.0 22.5 20 20 26 15.0 25.9 32.5 40 34.0 33.4 25 1.5 4 8.5 17.5 10.0 7.5 6.5 5.6 1.2 3.8 7.5 6.6 9.0 1.2
14 19.7 21 25 3 20.5 24.6 17.0 30.95 28.5 26.5 22 22 30 17.0 28.4 35.0 40 35.5 33.4 25 1.5 4 8.5 17.5 10.0 7.5 6.5 5.6 1.2 3.8 9.0 6.6 10.5 1.2
15 20.8 - - - 20.5 24.6 17.0 30.95 28.5 26.5 22 22 30 17.0 28.4 - - 35.5 33.4 25 - - - - - - 7.5 6.6 1.2 3.8 9.0 - 10.5 1.2
16 21.0 23 27 3 22.0 28.0 17.0 30.95 28.5 26.5 22 22 30 17.0 28.4 35.0 40 35.5 33.4 25 1.5 4 8.5 17.5 10.0 7.5 8.5 7.5 1.5 5.0 9.0 6.6 10.5 1.5
18 23.7 27 33 3 24.0 30.0 20.0 34.15 32.0 29.0 29 26 33 19.5 30.0 37.5 45 35.5 37.5 25 2.0 5 9.0 19.5 11.5 8.5 9.0 8.0 1.5 5.0 9.0 7.5 10.5 1.5
19 26.7 - - - - - 20.0 34.15 37.0 33.0 33 28 38 21.5 30.0 - - 35.5 37.5 25 - - - - - - - - - - 9.0 - 10.5 -
20 26.7 29 35 3 29.5 35.0 21.5 35.70 37.0 33.0 33 28 38 21.5 30.0 37.5 45 35.5 37.5 25 2.0 5 9.0 19.5 11.5 8.5 8.5 7.5 1.5 5.0 9.0 7.5 10.5 1.5
22 27.7 31 37 3 29.5 35.0 23.0 37.30 37.0 33.0 33 28 38 21.5 30.0 37.5 45 35.5 37.5 25 2.0 5 9.0 19.5 11.5 8.5 8.5 7.5 1.5 5.0 9.0 7.5 10.5 1.5
24 31.2 33 39 3 32.0 38.0 26.5 40.50 42.5 38.0 38 32 44 22.5 32.5 40.0 50 35.5 42.5 25 2.0 5 9.0 19.5 11.5 8.5 8.5 7.5 1.5 5.0 9.0 7.5 10.5 1.5
25 31.2 34 40 3 32.0 38.0 26.5 40.50 42.5 38.0 38 32 44 23.0 32.5 40.0 50 35.5 42.5 25 2.0 5 9.0 19.5 11.5 8.5 8.5 7.5 1.5 5.0 9.0 7.5 10.5 1.5
28 35.0 37 43 3 36.0 42.0 29.5 47.65 49.0 44.0 37 37 50 26.5 35.0 42.5 50 45.0 42.5 33 2.0 5 9.0 19.5 11.5 8.5 10.0 9.0 1.5 5.0 10.5 7.5 12.0 1.5
30 37.0 39 45 3 39.2 45.0 32.5 50.80 49.0 44.0 37 37 50 26.5 35.0 42.5 50 45.0 42.5 33 2.0 5 9.0 19.5 11.5 8.5 11.5 10.5 1.5 5.0 10.5 7.5 12.0 1.5
32 40.2 42 48 3 42.2 48.0 32.5 50.80 53.5 46.0 41 41 55 27.5 35.0 42.5 55 45.0 47.5 33 2.0 5 9.0 19.5 11.5 8.5 11.5 10.5 1.5 5.0 10.5 7.5 12.0 1.5
33 40.2 42 48 3 44.2 50.0 36.5 54.00 53.5 46.0 41 41 55 27.5 35.0 42.5 55 45.0 47.5 33 2.0 5 9.0 19.5 11.5 8.5 12.0 11.0 1.5 5.0 10.5 7.5 12.0 1.5
35 43.2 44 50 3 46.2 52.0 36.5 54.00 57.0 50.0 44 44 59 28.5 35.0 42.5 55 45.0 47.5 33 2.0 5 9.0 19.5 11.5 8.5 12.0 11.0 1.5 5.0 10.5 7.5 12.0 1.5
38 46.2 49 56 4 49.2 55.0 39.5 57.15 59.0 53.0 53 47 61 30.0 36.0 45.0 55 45.0 46.0 33 2.0 6 9.0 22.0 14.0 10.0 11.3 10.3 1.5 5.0 10.5 9.0 12.0 1.5
40 48.8 51 58 4 52.2 58.0 42.5 60.35 62.0 55.0 55 49 64 30.0 36.0 45.0 55 45.0 46.0 33 2.0 6 9.0 22.0 14.0 10.0 11.8 10.8 1.5 5.0 10.5 9.0 12.0 1.5
42 51.8 - - - 53.3 62.0 46.0 63.50 65.5 58.0 53 53 67 30.0 36.0 - - 53.0 51.0 41 - - - - - - 13.2 12.0 2.0 6.0 10.5 - 12.0 2.5
43 51.8 54 61 4 53.3 62.0 46.0 63.50 65.5 58.0 53 53 67 30.0 36.0 45.0 60 53.0 51.0 41 2.0 6 9.0 22.0 14.0 10.0 13.2 12.0 2.0 6.0 10.5 9.0 12.0 2.5
45 53.8 56 63 4 55.3 64.0 46.0 63.50 68.0 60.0 55 55 70 30.0 36.0 45.0 60 53.0 51.0 41 2.0 6 9.0 22.0 14.0 10.0 12.8 11.6 2.0 6.0 10.5 9.0 12.0 2.5
48 56.8 59 66 4 59.7 68.4 49.0 66.70 70.5 63.0 58 58 74 30.5 36.0 45.0 60 53.0 51.0 41 2.0 6 9.0 22.0 14.0 10.0 12.8 11.6 2.0 6.0 10.5 9.0 12.0 2.5
50 58.8 62 70 4 60.8 69.3 52.0 69.85 74.0 65.0 60 60 77 30.5 38.0 47.5 60 54.5 50.5 41 2.5 6 9.0 23.0 15.0 10.5 12.8 11.6 2.0 6.0 12.0 9.5 13.5 2.5
53 62.2 65 73 4 63.8 72.3 55.5 73.05 78.5 70.0 63 63 81 33.0 36.5 47.5 70 54.5 59.0 41 2.5 6 9.0 23.0 15.0 12.0 13.5 12.3 2.0 6.0 12.0 11.0 13.5 2.5
55 64.2 67 75 4 66.5 75.4 58.5 76.20 81.0 72.0 65 65 83 35.0 36.5 47.5 70 54.5 59.0 41 2.5 6 9.0 23.0 15.0 12.0 14.5 13.3 2.0 6.0 12.0 11.0 13.5 2.5
58 67.2 70 78 4 69.5 78.4 61.5 79.40 85.5 75.0 68 68 88 37.0 41.5 52.5 70 54.5 59.0 41 2.5 6 9.0 23.0 15.0 12.0 14.5 13.3 2.0 6.0 12.0 11.0 13.5 2.5
60 70.0 72 80 4 71.5 80.4 61.5 79.40 88.5 79.0 70 70 91 38.0 41.5 52.5 70 54.5 59.0 41 2.5 6 9.0 23.0 15.0 12.0 14.5 13.3 2.0 6.0 12.0 11.0 13.5 2.5
65 75.0 77 85 4 76.5 85.4 68.0 92.10 93.5 84.0 77 77 96 40.0 41.5 52.5 80 65.0 69.0 49 2.5 6 9.0 23.0 15.0 12.0 14.2 13.0 2.0 6.0 14.5 11.0 16.0 2.5
68 78.0 81 90 4 82.7 91.5 71.0 95.25 96.5 88.0 80 80 100 40.0 41.2 52.5 80 65.0 68.7 49 2.5 7 9.0 26.0 18.0 12.5 14.9 13.7 2.0 6.0 14.5 11.3 16.0 2.5
70 80.0 83 92 4 83.0 92.0 71.0 95.25 99.5 90.0 82 82 103 40.0 48.7 60.0 80 65.0 68.7 49 2.5 7 9.0 26.0 18.0 12.5 14.2 13.0 2.0 6.0 14.5 11.3 16.0 2.5
75 85.5 88 97 4 90.2 99.0 77.5 101.60 107.0 95.0 87 87 110 40.0 48.7 60.0 80 68.0 68.7 52 2.5 7 9.0 26.0 18.0 12.5 15.2 14.0 2.0 6.0 14.5 11.3 16.0 2.5
80 90.5 95 105 4 95.2 104.0 84.0 114.30 112.0 100.0 92 92 116 40.0 48.0 60.0 90 76.0 78.0 56 3.0 7 9.0 26.2 18.2 13.0 16.2 15.0 2.0 6.0 18.5 12.0 20.0 2.5
85 96.0 100 110 4 100.2 109.0 87.0 117.50 120.0 107.0 97 97 124 41.0 46.0 60.0 90 76.0 76.0 56 3.0 7 9.0 26.2 18.2 15.0 16.0 14.8 2.0 6.0 18.5 14.0 20.0 2.5
90 102.0 105 115 4 105.2 114.0 93.5 123.85 127.0 114.0 104 104 131 45.0 51.0 65.0 90 79.0 76.0 59 3.0 7 9.0 26.2 18.2 15.0 16.0 14.8 2.0 6.0 18.5 14.0 20.0 2.5
95 107.0 110 120 4 111.6 120.3 96.5 127.00 132.0 119.0 109 109 136 46.0 51.0 65.0 90 79.0 76.0 59 3.0 7 9.0 25.2 17.2 15.0 17.0 15.8 2.0 6.0 18.5 14.0 20.0 2.5
100 112.0 115 125 4 114.5 123.3 103.0 133.35 137.0 124.0 114 114 140 47.0 51.0 65.0 90 82.0 76.0 62 3.0 7 9.0 25.2 17.2 15.0 17.0 15.8 2.0 6.0 18.5 14.0 20.0 2.5

*) minimum diameter of the mating collar.

inch size available from size 0.375 to 4.000
Note: Additional technical & dimensional information will be provided on request.

62
 UFL850N Single Seals Standard Mechanical Seals - Metal Bellows Seals

Product Description Technical Features

1. Single seal configuration 1. Suitable for high temperature
2. Balanced design application
3. Independent of direction of rotation 2. No dynamically loaded O-ring
4. For plain shafts 3. Pumping screw for media with higher
5. Rotary metal bellows design viscosity also available
4. Short installation length possible
5. Rugged design for long operating life
6. Bellows design efficiently ensure
self-cleaning

l1k ±0.5 Typical Industrial Applications

Chemical industry
Cold media
(l9) Highly viscous media
Hot media
Power plant technology
9 ±0.5 Refining technology
Standards
EN 12756

Performance Capabilities
Sizes: d1 = Upto 100 mm (Upto 4.000’’)
Externally pressurized:
p1 = … 25 bar (363 PSI)
Internally pressurized:
1.3 1.2 1.1 2 3 p1 <120 °C (248 °F) 10 bar (145 PSI)
d 6 H11
d 7 H8
d1 h 6
d3

p1 <220 °C (428 °F) 5 bar (72 PSI)

Temperature: t= -40°C...+220°C (-40°F...+428°F)
l 3 ±0.5 l8 Stationary seat lock necessary.
Speed = 20 m/s (66 ft/s)
Materials
Seal face: Carbon graphite antimony
impregnated (A), Silicon carbide (Q12)
Seat: Silicon carbide (Q1)
Bellows: Inconel® 718 hardened (M6),
20

Hastelloy® C-276 (M5)

0

d8 Metal parts: CrNiMo steel (G), Duplex (G1),

Hastelloy® C-4 (M)
l5 l6 5
Stationary Seats
l6
Note: The item numbers as depicted above are based on our technical experience and
knowledge and are placed in the chronological order of their assembly procedure. l5
20 0

Item Part no. Description

Seal face l19
1.1 472/481
H11

with bellows unit

H8

l18
d6

d7

1.2 412.1 O-ring

1.3 904 Set Screw
2 475 Seat (G9) G16
3 412.2 O-ring (l1k shorter than specified by EN 12756)
DIN 24250

63
 Design Variations

0.5
UFL900N
Shaft diameter: d1= Upto 100 mm (Upto 4.000’’)
Internally pressurized: p1 = … 16 bar (232 PSI),
stationary seat lock necessary. UFL850F

ds -0.05
1.4 Dimensions, items and description as for
Externally pressurized: p1 = 10 bar (145 PSI)
Temperature: t = -40 °C... +220 °C (-40 °F...+428 °F) UFL850N, but with pumping screw (item no. 1.4).
Dependent on direction of rotation. The pumping
Speed = 20 m/s (66 ft/s) screw can be retrofitted.
UFL850P / UFL900P
Version with pumping ring. Dependent on direction
of rotation. Can be retrofitted.

Dimensional Data
Dimensions in millimeter

d1 d3 d6 d7 d8 ds l 1K l3 l5 l6 l8 l9 l 18 l 19 b s
16 30 23 27 3 38 42.5*) 32.5 1.5 4 17.5 10 - - 1.6 9.0
18 32 27 33 3 39 42 30.5 2 5 14 11.5 15 7.0 1.6 10.0
20 33.5 29 35 3 41 42 30.5 2 5 14 11.5 15 7.0 1.6 10.0
22 36.5 31 37 3 44 42 30.5 2 5 14 11.5 15 7.0 1.6 10.0
24 39 33 39 3 47 40 28.5 2 5 19.5 11.5 15 7.0 1.6 8.2
25 39.6 34 40 3 48 40 28.5 2 5 19.5 11.5 15 7.0 1.6 8.5
28 42.8 37 43 3 51 42.5 31 2 5 19.5 11.5 15 7.0 1.6 9.0
30 45 39 45 3 53 42.5 31 2 5 19.5 11.5 15 7.0 1.6 8.5
32 46 42 48 3 55 42.5 31 2 5 19.5 11.5 15 7.0 1.6 9.2
33 48 42 48 3 56 42.5 31 2 5 19.5 11.5 15 7.0 1.6 9.2
35 49.2 44 50 3 58 42.5 31 2 5 19.5 11.5 15 7.0 1.6 9.5
38 52.3 49 56 4 61 45 31 2 6 22 14 16 8.0 1.6 9.2
40 55.5 51 58 4 64 45 31 2 6 22 14 16 8.0 1.6 9.2
43 57.5 54 61 4 67 45 31 2 6 22 14 16 8.0 1.6 9.2
45 58.7 56 63 4 69 45 31 2 6 22 14 16 8.0 1.6 9.5
48 61.9 59 66 4 72 45 31 2 6 22 14 16 8.0 1.6 9.2
50 65 62 70 4 74 47.5 32.5 2.5 6 23 15 17 9.5 1.6 10.5
53 68.2 65 73 4 77 47.5 32.5 2.5 6 23 15 17 9.5 1.6 10.5
55 70 67 75 4 80 47.5 32.5 2.5 6 23 15 17 9.5 1.6 10.0
58 71.7 70 78 4 83 52.5 37.5 2.5 6 23 15 18 10.5 3.0 14.0
60 74.6 72 80 4 85 52.5 37.5 2.5 6 23 15 18 10.5 3.0 14.0
63 79 75 83 4 88 52.5 37.5 2.5 6 23 15 18 10.5 3.0 14.0
65 84.1 77 85 4 95 52.5 37.5 2.5 6 23 15 18 10.5 3.0 14.0
68 87.3 81 90 4 96 52.5 34.5 2.5 7 26 18 18.5 11.0 1.6 10.0
70 87.3 83 92 4 96 60 42 2.5 7 26 18 19 11.5 3.0 17.0
75 95 88 97 4 104 60 42 2.5 7 26 18 19 11.5 3.0 16.0
80 98.4 95 105 4 109 60 41.8 3 7 26.2 18.2 19 11.5 3.0 16.0
85 104.7 100 110 4 114 60 41.8 3 7 26.2 18.2 19 11.5 3.0 16.0
90 111 105 115 4 119 65 46.8 3 7 26.2 18.2 20.5 13.0 3.0 21.0
95 114 110 120 4 124 65 47.8 3 7 25.2 17.2 20.5 13.0 3.0 21.0
100 117.4 115 125 4 129 65 47.8 3 7 25.2 17.2 20.5 13.0 3.0 20.0
*) Installation length is longer than l1k specified by EN 12756
inch size available from size 0.625 to 4.000
Note: Additional technical & dimensional information will be provided on request.

64
 UFL650 Single Seals Standard Mechanical Seals - Metal Bellows Seals

Product Description Technical Features

1. Single seal configuration 1. S u i t a b l e f o r h i g h t e m p e r a t u r e
2. Balanced design application
3. Independent of direction of rotation 2. Can handle high sliding velocities
4. Stationary metal bellows design 3. No elastomer secondary seals
4. Rugged design for long operating life
5. Bellows design efficiently ensure self-
cleaning

l ±0.5
t Typical Industrial Applications Materials
1 Chemical industry Bellows: Inconel 718 (M6), Hastelloy® C-276 (M5)
®
nxmx

High sliding velocities Seal face: Carbon graphite antimony

Hot media impregnated (A), Silicon carbide (Q12)
Power plant technology Seat: Silicon carbide (Q1), Special cast
Refining technology CrMo steel (S)
Metal parts: Duplex (G1), Carpenter® 42
2 1.1 1.2 Performance Capabilities
(T4), Hastelloy® C-4 (M)
d 6 H8

Sizes: d1 = Upto 100 mm (Upto 4.000’’)

d4

d5

d1
d2
d3

Externally pressurized: p1 = 25 bar (363 PSI), Design Variations

(higher pressure possible, please inquire) UFL690
Internally pressurized:
Shaft diameter: d1 = Upto100 mm (Upto 4.000’’),
p1 <120 °C (248 °F) 10 bar (145 PSI), (>100 mm on request)
p1 <220 °C (428 °F) 5 bar (72 PSI), Internally pressurized: p1 = 16 bar (232 PSI),
p1 <400 °C (752 °F) 3 bar (44 PSI) (higher pressure possible, please enquire)
Note: The item numbers as depicted above are based on our technical experience and Stationary seat lock necessary. Externally pressurized: p1 = 10 bar (145 PSI),
knowledge and are placed in the chronological order of their assembly procedure. Temperature: t= -20°C...+400°C (-4°F...+752°F) stationary seat lock necessary.
Speed: = 50 m/s (165 ft/s) Temperature: t= - 20°C...+ 400°C (- 4°F...+752°F)
Item Part no. Description Speed = 50 m/s (165 ft/s)
Seal face
1.1 472/481
with bellows unit
1.2 400.1 Flat gasket
2 475 Seat
DIN 24250
Dimensional Data
Dimensions in millimeter

d d1 d2 d3 d4 d5 d6 l nx mx t
19 16-19 20.5 29 30.3 25.3 45.0 33.5 4xM4 6
24 20-24 25.5 35 38.8 33.8 49.0 33.5 4xM4 6
30 25-30 31.5 40 43.6 38.6 55.0 34.5 6xM4 6
35 31-35 36.0 45 45.8 40.8 59.0 33.0 6xM4 6
40 36-40 41.0 50 51.5 46.5 65.0 30.5 6xM4 6
45 41-45 46.0 55 55.2 50.2 69.0 35.5 6xM4 6
51 46-51 52.0 63 64.7 59.7 76.5 40.5 6xM5 7
60 52-60 61.0 70 70.6 65.6 84.0 32.0 6xM5 7
70 61-70 71.0 80 82.8 76.8 95.0 38.0 6xM5 7
82 71-82 83.5 95 98.0 92.0 112.0 41.0 6xM6 7
88 83-88 89.5 100 107.7 101.7 120.0 47.0 6xM6 7
100 89-100 101.0 112 112.7 106.7 130.0 47.0 6xM6 7
inch size available from size 0.625 to 4.000
Note: Additional technical & dimensional information will be provided on request.

65
UFLWT Single Seals Standard Mechanical Seals - Metal Bellows Seals

Product Description Technical Features

1. Single seal configuration 1. Suitable for very high temperature
2. Balanced design application
3. Independent of direction of rotation 2. No dynamically loaded O-ring
4. For plain shafts 3. Pumping screw for media with higher
5. Rotary metal bellows design viscosity also available
4. Short installation length possible
5. Rugged design for long operating life
6. Bellows design efficiently ensure self-
cleaning

l1 ± 0.5 Design Variations Typical Industrial Applications

(l9) Chemical industry Power plant technology
UFLWT900
Highly viscous media Refining technology
l7 ± 0.5
Shaft diameter: d1 = Upto150 mm (Upto 6.000’’) Hot media
f
mx Internally pressurized: p1 = … 16 bar (232 PSI) Materials
Externally pressurized: p1 = 10 bar (145 PSI) Seal face: Carbon graphite antimony
Temperature: t= - 20°C..+400°C (-4°F..+752°F) impregnated (A), Silicon carbide (Q12)
stationary seat lock necessary. Seat: Silicon carbide (Q1)
Speed: = 20 m/s (66 ft/s) Bellows: Inconel® 718 hardened (M6),
1.5 1.3 1.2 1.1 2 3
d6 H11

Hastelloy® C-276 (M5)

d 1 h6

d7 H8
d3

1.4 l 3 ± 0.5 l8 Metal parts: CrNiMo steel (G), Duplex (G1),

Carpenter® 42 (T4), Hastelloy® C-4 (M)
Item Part no. Description Performance Capabilities
Seal face Sizes: d1 = Upto 150 mm (Upto 6.000’’)
1.1 472/481
with bellows unit
20

d8 Externally pressurized:
0

k 1.2 410 Sealing Ring

l5 l6 5 p1 = … 25 bar (363 PSI)
1.3 474 Drive Collar Internally pressurized:
Note: The item numbers as depicted above are based on our technical experience and 1.4 Socket head screw p1 <120 °C (248 °F) 10 bar (145 PSI)
knowledge and are placed in the chronological order of their assembly procedure.
1.5 904 Set screw p1 <220 °C (428 °F) 5 bar (73 PSI)
2 475 Seat p1 <400 °C (752 °F) 3 bar (44 PSI)
3 412 Sealing Ring Stationary seat lock necessary
DIN 24250 Temperature: t = -20 °C...+400 °C (-4 °F...+752 °F)
Speed = 20 m/s (66 ft/s)
Dimensional Data
Dimensions in millimeter
d1 d3 d6 d7 d8 l1 l3 l5 l6 l7 l8 l9 f k mx
16 38 29.0 35.0 3 58.0 46.5 2.0 5 9 19.5 11.5 5 5 M5
18 40 31.0 37.0 3 58.0 46.5 2.0 5 9 19.5 11.5 5 5 M5
20 42 34.0 40.0 3 58.0 46.5 2.0 5 9 19.5 11.5 5 5 M5
22 44 37.0 43.0 3 58.0 46.5 2.0 5 9 19.5 11.5 5 5 M5
24 46 37.0 43.0 3 58.0 46.5 2.0 5 9 19.5 11.5 5 5 M5
25 47 39.0 45.0 3 58.0 46.5 2.0 5 9 19.5 11.5 5 5 M5
28 50 42.0 48.0 3 58.0 46.5 2.0 5 9 19.5 11.5 5 5 M6
30 52 44.0 50.0 3 58.0 46.5 2.0 5 9 19.5 11.5 5 5 M6
32 54 49.0 56.0 4 60.5 46.5 2.0 6 9 22.0 14.0 5 5 M6
33 55 49.0 56.0 4 60.5 46.5 2.0 6 9 22.0 14.0 5 5 M6
35 57 51.0 58.0 4 60.5 46.5 2.0 6 9 22.0 14.0 5 5 M6
38 60 54.0 61.0 4 60.5 46.5 2.0 6 9 22.0 14.0 5 5 M6
40 66 56.0 63.0 4 61.5 47.5 2.0 6 9 22.0 14.0 5 6 M6
43 69 59.0 66.0 4 61.5 47.5 2.0 6 9 22.0 14.0 5 6 M6
45 71 62.0 70.0 4 62.5 47.5 2.5 6 9 23.0 15.0 5 6 M6
48 74 65.0 73.0 4 62.5 47.5 2.5 6 9 23.0 15.0 5 6 M6
50 76 67.0 75.0 4 62.5 47.5 2.5 6 9 23.0 15.0 5 6 M6
53 79 70.0 78.0 4 62.5 47.5 2.5 6 9 23.0 15.0 5 6 M6
55 81 72.0 80.0 4 62.5 47.5 2.5 6 9 23.0 15.0 5 6 M6
58 85 75.0 83.0 4 68.0 53.0 2.5 6 9 23.0 15.0 5 6 M6
60 87 77.0 85.0 4 68.0 53.0 2.5 6 9 23.0 15.0 6 6 M8
63 90 81.0 90.0 4 71.0 53.0 2.5 7 9 26.0 18.0 6 6 M8
65 92 83.0 92.0 4 71.0 53.0 2.5 7 9 26.0 18.0 6 6 M8
68 95 88.0 97.0 4 71.0 53.0 2.5 7 9 26.0 18.0 6 6 M8
70 97 88.0 97.0 4 71.0 53.0 2.5 7 9 26.0 18.0 6 6 M8
75 102 95.0 105.0 4 71.0 52.8 3.0 7 9 26.2 18.2 6 6 M8
80 107 100.0 110.0 4 71.0 52.8 3.0 7 9 26.2 18.2 6 6 M8
85 112 105.0 115.0 4 71.0 52.8 3.0 7 9 26.2 18.2 6 6 M8
90 117 110.0 120.0 4 71.0 53.8 3.0 7 9 25.2 17.2 6 6 M8
95 122 115.0 125.0 4 71.0 53.8 3.0 7 9 25.2 17.2 6 6 M8
100 127 122.2 134.3 5 74.0 54.0 3.0 9 11 30.0 20.0 6 6 M8
inch size available from size 0.625 to 4.000
Note: Additional technical & dimensional information will be provided on request.
66
 GSPH-K Single & Dual Seals Mechanical Seals For Pumps - Gas Lubricated

Product Description Technical Features

1. Single and Dual seal configuration 1. Seal faces are designed to be non-
2. Balanced design contacting during operation
3. For stepped shafts 2. Designed for environmental protection
4. Rotary unit with multiple springs with high efficiency
5. Designed to remain in closed position in 3. Due to non-contacting design there is
the event of buffer pressure failure no friction on the seal faces and there is
6. Can accommodate reverse pressure no heat generated at the seal or in the
7. Gas-lubricated design medium
8. Gas grooves design is available in V- 4. Trouble free operations as complex
grooves and U-grooves (independent components are not required to
of direction of rotation) dissipate frictional heat
5. Differential pressure not required with
hard / soft material combination
6. Conforms to containment seal in
accordance with API 682

Typical Industrial Applications

Chemical industry Gases not harmful to the
l1k Refining technology environment (single seal)
Gases and liquids Fans
l2 l 7 + 0.5 (single seals only gas) Small steam turbines
Gases and liquids which Blowers
l6 must not get into the Roots compressors
atmosphere (dual seal) Pumps
l5
Performance Capabilities
Shaft diameter: d1 = 28 ... 125 mm (1.10" ... 4.92")
Pressure: p1 = 25 bar (363 PSI)
Temperature: t* = -20 °C...+170 °C (- 4 °F...+338 °F)
Sliding velocity: vg = 4 ... 25 m/s (13 ... 82 ft /s)
* Depending on resistance of O-rings
Materials
Seal face: Carbon graphite antimony impregnated (A),
Silicon carbide (Q2), alternatively: Carbon graphite resin
impregnated (B), Silicon carbide (Q1) Seat: Silicon carbide
(Q1, Q2),
Silicon carbide (Q19, Q 29) with seal face in Q1 resp. Q2
3)

Metal parts: CrNiMo steel (G)

4)

1.4 1.5 1.3 1.1 2

d 6 H11
d 7 H8
d2 h 6

Standards
d1
d3

3 1) EN 12756
1.6 5) 1.2 R1 3 API 682 / ISO 21049
.6
10
02
)

Item Part no. Description

1.1 472 Sliding face
1.2 412.1 O-ring
1.3 474 Thrust ring
1.4 485 Drive collar
1.5 477 Spring
mx 1.6 904 Set screw
2 475.1 Seat
f
3 412.3 O-ring

Note: The item numbers as depicted above are based on our technical experience and
DIN 24250
knowledge and are placed in the chronological order of their assembly procedure.
1) d1 > 105: 2 mm x 30°
2)
d1 > 105: 30°
3) d > 105: +0.1
1
4)
d1 > 105: H7
5)
3 x 120°

67
 Design Variations

l1 F
CSV GBI
GBI 76 72
74

l4

CSD
75

GSPH-KD GSPH Tandem arrangement

Double seal back-to-back, buffered with gas, according According to API 682
to API 682 configuration 3NC-BB, Plan 74. Items, Configuration: 2CW-CS, Plan 72, 75, 76.
descriptions and unspecified dimensions as for GSPH-K. For media with a gaseous leakage. B750VN on the
Pressure: p1 = ... 22 bar (319PSI), p3 = ... 25 bar (363 PSI) product side. In case of a failure, the GSPH on the
(over the whole nominal diameter range, higher values atmosphere side works as a liquid seal.
on request).
Differential pressure Δp = min. 3 bar (44 PSI)
Other operating limits as GSPH-K.

Dimensional Data

Dimensions in millimeter
d1 d2 d3 d6 d7 l1K l 1' l2 l 4' l5 l6 l7 f mx
28* 33 53 37.0 43.0 50.0 89 20 44.5 2.0 5 9 5 M6
30* 35 55 39.0 45.0 50.0 89 20 44.5 2.0 5 9 5 M6
32* 38 60 42.0 48.0 50.0 89 20 44.5 2.0 5 9 5 M6
33* 38 60 42.0 48.0 50.0 89 20 44.5 2.0 5 9 5 M6
35* 40 62 44.0 50.0 50.0 89 20 44.5 2.0 5 9 5 M6
38* 43 65 49.0 56.0 52.5 95 23 47.5 2.0 6 9 5 M6
40* 45 67 51.0 58.0 52.5 95 23 47.5 2.0 6 9 5 M6
43* 48 70 54.0 61.0 52.5 95 23 47.5 2.0 6 9 5 M6
45* 50 72 56.0 63.0 52.5 95 23 47.5 2.0 6 9 5 M6
48* 53 75 59.0 66.0 52.5 95 23 47.5 2.0 6 9 5 M6
50* 55 77 62.0 70.0 57.5 104 25 52.0 2.5 6 9 5 M6
53* 58 84 65.0 73.0 57.5 104 25 52.0 2.5 6 9 5 M6
55* 60 86 67.0 75.0 57.5 106 25 53.0 2.5 6 5 M6
9
58* 63 89 70.0 78.0 62.5 112 25 56.0 2.5 6 7 M8
9
60* 65 91 72.0 80.0 62.5 112 25 56.0 2.5 6 7 M8
9
63* 68 94 75.0 83.0 62.5 112 25 56.0 2.5 6 7 M8
9
65* 70 97 77.0 85.0 62.5 112 25 56.0 2.5 6 7 M8
9
70* 75 104 83.0 92.0 70.0 126 28 63.0 2.5 7 7 M8
9
75* 80 109 88.0 97.0 70.0 126 28 63.0 2.5 7 7 M8
85 114 95.0 70.0 126 28 63.0 3.0 7 9 7 M8
80* 105.0
85* 90 119 100.0 75.0 126 28 63.0 3.0 7 9 7 M8
110.0
90* 95 124 105.0 115.0 75.0 126 28 63.0 3.0 7 9 7 M8
95* 100 129 110.0 120.0 75.0 126 28 63.0 3.0 7 9 7 M8
100* 105 132 115.0 125.0 75.0 126 28 63.0 3.0 7 9 7 M8
105* 115 153 122.2 134.3 73.0 136 32 68.0 2.0 10 – 7 M8
110* 120 158 128.2 140.3 73.0 136 32 68.0 2.0 10 – 7 M8
115* 125 163 136.2 148.3 73.0 136 32 68.0 2.0 10 – 7 M8
120* 130 168 138.2 150.3 73.0 136 32 68.0 2.0 10 – 7 M8
125* 135 173 142.2 154.3 73.0 136 32 68.0 2.0 10 – 7 M8

* EN 12756
inch size available from size 1.125" to 5.000"
Note: Additional technical & dimensional information will be provided on request.

68
 CTX - GSDN Dual Seals Standard Cartridge Seals For Pumps - Gas Lubricated

Product Description Technical Features

1. Dual seal configuration 1. Seal faces are designed to be non-
2. Balanced design contacting during operation
3. Cartridge construction 2. Designed for environmental protection
4. Stationary design with multiple springs with high efficiency
5. Seat design is rotary 3. Due to non-contacting design there is
6. Designed to remain in closed position in no friction on the seal faces and there is
the event of buffer pressure failure, no heat generated at the seal or in the
7. Can accommodate reverse pressure medium
8. Gas-lubricated design 4. Trouble free operations as complex
9. Gas grooves design is available in V- components are not required to
grooves and U-grooves (independent dissipate frictional heat
of direction of rotation)

5 Typical Industrial Applications

( 7) Chemical industry
6
Refining technology
Gases and liquids
4
Media which require high purity
Environmental harmful media
Pumps

Materials
Seal face: Silicon carbide (Q1/Q19)
Seat: Silicon carbide (Q19/Q1)
Secondary seals: FKM (V), EPDM (E), FFKM (K)
Spring: Hastelloy® C-4 (M)
Metal parts: CrNiMo steel (G), Hastelloy® C-4 (M)

Performance Capabilities
14 13 5 1 2 3 10 9 11 12 15
Shaft diameter:
d1 h 6

d1 = 30 … 100 mm (1.18" ... 3.94")

d2
d3

Pressure:
16 17 18 4 21 8 6 7 20 19 p1 = 13 bar (189 PSI),
p3 = 16 bar (232 PSI)
with V-grooves (uni-directional)
p1 = 9 bar (131 PSI),
p3 = 12 bar (174 PSI)
with U-grooves (bi-directional)
Differential pressure (p3 - p1) = min. 3 bar (44 PSI)
Operating temperature limits for:
EPDM - 20 °C … +140 °C (-4 °F ... +284 °F)
FFKM - 5 °C … +300 °C ( +23 °F ... +572 °F)
FKM - 20 °C … +170 °C (- 4 °F ... +338 °F)
Speed = 4 … 15 m/s (13 ... 49 ft/s)
Note: The item numbers as depicted above are based on our technical experience and
Axial movement: ± 1.0 mm
knowledge and are placed in the chronological order of their assembly procedure.

Item Description Item Description

1,9 Seal face 14 Ring
2,5,7,10,12,18 O-ring 15 Set screw
3 Spring 16 Retaining ring
4,11 Seat 17 Counter-sunk socket screw
6 Shaft sleeve 19 Assembly fixture
8 Cover 20 HSH Cap Screw
13 Adapter 21 Gasket

69
 Installation, Details, Options

da Seal cover

O
45 O
45

a2

S
Dimensional Data

Dimensions in millimeter
d1 d2 d3 min. d3 max. l4 l5 l6 l7 a2 da s
30 52.0 54 57 25.4 86 33 53 67 105 14
33 55.0 57 60 25.4 86 33 53 70 108 14
35 57.5 59 62 25.4 86 33 53 72 110 14
38 61.0 63 70 25.4 86 33 53 75 123 14
40 61.0 63 70 25.4 86 33 53 77 123 16
43 64.0 66 70 25.4 86 33 53 80 133 16
45 67.0 68 75 25.4 86 33 53 82 138 16
48 70.0 71 77 25.4 86 33 53 85 138 16
50 71.0 73 78 25.4 86 33 53 87 148 16
53 75.3 77 82 28.5 89 33 56 97 148 18
60 83.5 85 90 28.5 89 33 56 104 155 18
65 93.0 95 102 25.4 100 41.6 58.4 116 163 18
70 101.0 102 110 25.4 100 41.6 58.4 124 178 18
75 107.0 108 119 28 107 41.6 65.4 129 193 18
80 111.0 111 124 28 107 41.6 65.4 129 198 18
90 121.0 121 131 28 107 41.6 65.4 140 205 22
100 130.0 132 144 28 107 41.6 65.4 154 218 22

Note: Additional technical & dimensional information will be provided on request.

70
 GSAZ Dual Seals Agitator Seals - Gas Lubricated

Product Description Technical Features

1. Dual seal configuration 1. Seal faces are designed to be non-
2. Balanced design contacting during operation
3. Independent of direction of rotation 2. Designed for environmental protection
4. Cartridge construction with high efficiency
5. Gas-lubricated design 3. Due to non-contacting design there is
6. Designed for top entry vessels no friction on the seal faces and there is
no heat generated at the seal or in the
medium
4. Trouble free operations as complex
components are not required to
dissipate frictional heat
5. To accommodate large axial movement
torque transmission is through
clamping ring
6. Rotating seat is designed and arranged
in the center

d7
1) Typical Industrial Applications
h6
Agitators
22 Chemical industry
Environmental harmful media with double
l2

seals
Food and beverage industry
Gases and liquids
Media which require high purity
l3

G
Pharmaceutical industry
1)
C Item Description Performance Capabilities
d3 h8
Shaft diameter: d3 = 40 ... 220 mm (1.6" … 8.7")
L2

1 Seal face(Diamond Coated),

atmosphere side Pressure p1 = vacuum ... 6 bar (87 PSI),
L1

1 6
Δp = min. 3 bar (44 PSI), p3 = 9 bar (131 PSI)
A
11 2 Seal face (Q1), product side Temperature: t1= -20°C... +150°C (-4°F…+302°F),
2x M 2 d2 with cooling flange 250 °C (482 °F)
6,7 O-ring
2
Speed = 0 ... 10 m/s ( 0 ... 33 ft/s)
7 11 Seat (Q1)
Standards
l1

17
17 Flange
1.5

DIN 28136 T2 (for steel vessels)

22 Clamping ring DIN 28141 (flange connection for steel vessels)
8.5

30 0
d0
a DIN 28154 (shaft end for steel vessel)
d 4 e8 DIN 28136 T3 (for glass-lined vessels)
k
DIN 28137 T2 (flange connection for glass-lined
vessels)
d1
Design Variations Notes
Options:
2x M 2 d2 GSAZ184K(L)-D Cooling or heating flange
Double seal (with integrated bearing) for Flush
Polymerization barrier
steel vessels to DIN 28136, connection
7 l1

flange to DIN 28141 and shaft ends Installation, Details, Options

to DIN 28154.
15 ± 0.1

F, G

d8
H8
d4 f8 M1
k1 A
S
d1 Flange connection acc. to DIN 28137 T2 C
for nominal diameters 40 ... 100.
Note: The item numbers as depicted above are based on our technical experience and
M2
knowledge and are placed in the chronological order of their assembly procedure.

Torque Transmissions E, G
Supply connections
Designation and positions of supply connections,
pull-off and jacket threads acc. to DIN 28138 T3.
A Barrier gas IN
C Leakage
E Cooling IN
F Cooling OUT
S Flush
Shrink disk Clamping ring Clamping ring G Grease
with pin

71
 Installation, Details, Options

E
D
ls

l5
F
E D
D
F

Option Option Option Option

Cooling flange, can be used Leakage drain, can be used Leakage drain, can be used Polymerization barrier, can be
alternatively as a heating flange alternatively as a flush or as a heating alternatively as a flush used alternatively as a leakage
(tmax. = 350°C (662 °F). flange. drain or a flush.

Design Variations
GSAZ164K(L)-D
Double seal (with integrated bearing) for glass-lined
vessels to DIN 28136, connection flange to DIN 28137
and shaft ends to DIN 28159.
G

Flange connection acc. to DIN 28137 T2

for nominal diameters 125 ... 161.

Dimensional Data
GSAZ184 - Dimensions in millimeter

d3 1) d7 1) d1 nxd 2 2 d4 d0 k L1 L2 L w1) l1 l2 l3 a M1 M2 A, B
40 38 175 4x18 110 90 145 81 137 143 15 35 28 122 M12 M16 G3/8
50 48 240 8x18 176 135 210 82.5 130.5 148 17 42 28 155 M12 M16 G3/8
60 58 240 8x18 176 135 210 78.5 128 158 18 39 28 176 M12 M16 G3/8
80 78 275 8x22 204 155 240 94.5 146 168 20 50 34 203 M16 M20 G1/2
100 98 305 8x22 234 190 270 95 156.5 178 20 56.5 34 228 M16 M20 G1/2
125 120 330 8x22 260 215 295 95 163.5 203 20 60 39 268 M20 M20 G1/2
140 135 395 12x22 313 250 350 97 168.5 208 20 82 41 285 M20 M20 G1/2
160 150 395 12x22 313 265 350 97 176.5 213 25 81 41 302 M20 M20 G1/2
180 170 445 12x22 364 310 400 - - 233 25 - - 332 M24 M20 G1/2
200 190 445 12x22 364 310 400 - - 243 25 - - 352 M24 M20 G1/2
220 210 505 16x22 422 340 460 - - 263 25 - - - M24 M20 G1/2

1) Shaft diameters d 3 and d 7 to DIN 28154

GSAZ164 - Dimensions in millimeter

d31) d71) Nominal size Flange size 2) d1 nxd 2 d4 nxd 5 d6 d7 k1 k2 l1 l2 l1 l2 I3 l4 l5 M1 M2 A
40 38 40 E125 175 4x18 110 – – 102 145 – 142 184 25 35 28 50 50 M12 M16 G3/8
50 48 50 E200 240 8x18 176 – – 138 210 – 147 195 25 40 28 50 50 M12 M16 G3/8
60 58 60 E250 275 8x22 204 – – 188 240 – 158 203 25 42 28 50 60 M12 M20 G3/8
80 78 80 E300 305 8x22 234 – – 212 270 – 170 240 30 45 34 60 60 M16 M20 G1/2
100 98 100 E400 395 12x22 313 – – 268 350 – 177 240 30 52 34 60 60 M16 M20 G1/2
100 98 100 E500 395 12x22 313 – – 268 350 – 177 240 30 52 34 60 60 M16 M20 G1/2
125 120 125 E700 505 4x22 422 12x22 320 306 460 350 208 266 30 75 40 60 80 M20 M20 G1/2
140 135 140 E700 505 4x22 422 12x22 320 306 460 350 223 282 30 79 40 60 80 M20 M20 G1/2
160 150 160 E700 505 4x22 422 12x22 320 306 460 350 228 282 30 77 40 60 85 M20 M20 G1/2
160 150 160 E900 505 4x22 422 12x22 320 306 460 350 228 282 30 77 40 60 85 M20 M20 G1/2
160 150 161 E901 565 4x26 474 12x22 370 356 515 400 228 282 30 77 40 60 85 M20 M20 G1/2

1) Shaft diameters d 3 and d 7 to DIN 28159

2) Flange size to DIN 28137T2
Note: Additional technical & dimensional information will be provided on request

72
 UR-D Dual Seals Agitator Seals - Liquid Lubricated

Product Description Technical Features

1. Dual seal configuration 1. Design with CIP-/SIP (Cleaning in
2. Unbalanced design Place, Sterilization in Place)
3. Independent of direction of rotation 2. Smooth construction of surfaces with
4. Cartridge construction no empty crevices
5. Designed for top, side and bottom entry 3. Sterile application design available
vessels 4. Rugged design to ensure long term
6. Design of the product side seat is rotary reliability and operating life
5. Seals are assembled in cartridge
construction for easy fitment
6. Over all connecting dimensions are
tailor made to customer's
specifications

l5 l2 l6 l4

l4

Variant
Without bearing

B
nxd 5

Variant
UR5..-D

2 3 1 6 4 5

dW

d8
dN
d3

d2

d1

Variant
UR34..-D

T C G

Variant
With bearing
A

l4

l1 l2 l3 l4

Note: The item numbers as depicted above are based on our technical experience and
knowledge and are placed in the chronological order of their assembly procedure.

Item Description Installation, Details, Options Supply Connections

1 Seal face, product side B A Barrier fluid IN
2 Seat, product side B Barrier fluid OUT
3 O-ring, dynamic C Drainage
4 Seal face, atmosphere side T G Grease
G
G
5 Seat, atmosphere side T Temperature measuring
6 O-ring, dynamic
A, C

73
 Typical Industrial Applications Standards Performance Capabilities
Chemical industry Kneaders FDA Sizes: dN /d w = Upto 200 (500) mm
Food and beverage industry Mills (Upto 7.875” (20.00”))
Notes
Pharmaceutical industry Mixers Axial offset shaft/housing:
Dryers Pressure filters Options:
Cooling or heating flange dN /d w 30... 60mm (1.18”...2.36”): max. ±1.5mm
Reactors
Temperature probe (0.059”)
Materials Axial expansion joint (shaft lifting) dN /d w >60 mm (2.36”): max. ±2.0 mm (0.079”)
Product side : Wiper ring (shaft lifting) Radial offset shaft/housing: max. ±0.3 mm
Seal face, seat: Silicon carbide (Q1), (0.012”)
Tungsten carbide (U) Pressure:
Metal parts: Cr steel (E), CrNiMo steel (G),
Hastelloy ® (M) p1 (media) = vacuum...14 (23) bar (203
(334 PSI))
Atmosphere side:
Seal face, seat: Silicon carbide (Q1), Carbon p3 (buffer fluid) = max. 16 (25) bar (232
graphite resin impregnated (B) (363 PSI))
Metal parts: Cr steel (E), CrNiMo steel (G) Δ p3 > p1 = min. 2 bar (29 PSI), max. 10 bar
Product and atmosphere side: (145 PSI)
Springs: CrNiMo steel (G), Hastelloy ® (M) Temperature:
Secondary seals: EPDM (E), FKM (V), t1 (media) = -20 °C ... +200 (300) °C
FFKM (K), FKM, FEP wrapped (M5) (- 4 °F ... +392 (572) °F)
Other materials on request. Speed = 20 m/s (66 ft /s)

Torque Transmissions

Drive key Clamping set Shrink disc Clamping ring Clamping ring
with pin
Dimensional Data
Dimensions in millimeter
dN dW d1 d2 d3 d8 l1 l2 l3 l4 l5 l6 l7 A,B nxd 5
30 20 52 117 140 118 35 30 114 30 22 75 41 G3/8 6X11
35 25 58 124 150 128 35 30 127 30 22 85 41 G3/8 6X11
40 30 62 134 165 138 35 30 129 30 24 87 41 G3/8 6X11
45 35 68 140 175 148 35 30 130 30 24 87 41 G3/8 6X11
50 40 75 145 175 148 35 30 133 34 26 90 41 G3/8 8X11
55 45 82.7 150 175 148 35 30 135 34 26 90 41 G3/8 8X11
60 50 85 160 185 158 41 30 150 34 30 105 41 G3/8 8X11
65 50 90 170 195 168 41 30 160 34 30 105 41 G3/8 8X11
70 55 95 175 205 178 41 30 160 34 30 105 41 G3/8 8X11
75 60 100 180 205 178 41 30 160 34 30 105 41 G3/8 8X11
80 65 110 190 220 188 41 40 190 44 30 105 41 G3/8 8X14
85 70 115 195 230 198 41 40 190 44 30 105 41 G3/8 8X14
90 75 120 200 230 198 41 40 190 44 30 105 41 G3/8 8X14
95 80 127 205 235 203 41 40 190 44 30 105 41 G3/8 8X14
100 80 130 210 240 208 41 40 190 44 30 105 45 G3/8 8X14
105 85 135 215 250 218 41 40 190 44 30 105 45 G1/2 8X14
110 90 140 230 260 228 41 40 190 44 31 110 45 G1/2 8X14
115 95 145 235 270 238 41 40 190 44 31 110 45 G1/2 8X14
120 100 150 240 270 238 42 40 200 44 31 120 46 G1/2 8X14
130 110 160 255 290 258 42 40 200 50 31 120 46 G1/2 8X14
140 120 172 265 305 268 43 50 220 50 41 130 46 G1/2 8X18
150 130 185 275 315 278 43 50 220 50 41 130 46 G1/2 8X18
160 140 195 290 335 298 43 50 220 50 41 130 46 G1/2 8X18
170 150 205 300 335 298 47 50 220 50 45 130 46 G1/2 8X18
180 160 220 330 355 323 47 50 250 50 45 140 46 G1/2 8X18
190 170 230 345 375 358 47 50 250 55 45 140 46 G1/2 8X18
200 180 240 365 395 358 47 50 250 55 45 140 51 G1/2 8X18
210 190 260 385 415 378 50 50 250 55 45 140 51 G1/2 12X18
220 190 270 395 425 388 50 50 250 55 45 140 51 G1/2 12X18
230 200 280 395 425 388 50 50 300 55 45 160 51 G1/2 12X18
dN > 230 on request
inch size available from size 1.125 to 9.000
Note: Additional technical & dimensional information will be provided on request.

74
 MXS Single & Dual Seals Agitator Seals – Dry Running

Product Description Technical Features

1. Single and Dual seal configuration 1. Over all connecting dimensions are
2. Balanced design tailor made to customer's specifications
3. Independent of direction of rotation 2. Can accommodate reverse pressure
4. Cartridge construction 3. The seal design is unique as it closes
5. Designed for dry running applications due to the hydraulic product pressure
6. Designed for top entry vessels, side as well as overlaying barrier pressure
entry can be provided upon request 4. Rugged design to ensure long term
7. Rotary unit with multiple springs reliability and operating life
5. Seals are assembled in cartridge
construction for easy fitment and are
also available in component design as
per customer specification

Typical Industrial Applications

Chemical industry
X Food and beverage industry
Non-toxic media with single seal
d3
Pharmaceutical industry
Toxic media with double seal
Agitators
Reactors
11 Standards
FDA
3

3
2

ATEX
1
DIN 28136 T2 (for steel vessels)
DIN 28141 (flange connection for steel vessels)
6
DIN 28154 (shaft end for steel vessels)
DIN 28136 T3 (for glass-lined vessels)
26

5 DIN 28137 T2 (flange connection for glasslined vessels)

DIN 28159 (shaft end for glass-lined vessels)

d1 h8 Materials
Seal face: Carbon graphite, FDA conform
d2
Seat: Silicon carbide (Q1)
d4 Secondary seals and metal parts according to
d5
application and customer's specifications

Notes
Seat alternatives available on request.
Note: The item numbers as depicted above are based on our technical experience and Options:
knowledge and are placed in the chronological order of their assembly procedure. Cooling or heating flange
Flush
Polymerization barrier
Installation, Details, Options
X
s

E
ls

F
D D
a1

Option Option Option

Cooling flange, can be used alternatively Leakage drain, can be used Polymerization barrier, can be used
Seal flange as a heating flange (t max. = 350°C (662 °F). alternatively as a flush. alternatively as a leakage drain or a flush.

Item Description Performance Capabilities

1 Seal face with seal face housing Sizes: d1 = Upto 160 mm (Upto 6.500’’)
3 Drive collar Pressure: p1 = vacuum ... 6 bar (87 PSI)
5 Flange Temperature: t1 = - 20 °C ... +150 (250*) °C (- 4 °F ... 302 (482*) °F
Speed = 0 ... 2 m/s (0 ... 6 ft/s)
6 Seat with seat housing Permissible axial movement: ± 1.5 mm
11 Clamping Radial movement: ± 1.5 mm

75
 Design Variations

G G
C C

D D

MXS-110 Single Seal Variants Double Seal Variants

The MXS-110 is equipped in addition with a MXS184 MXS184-D
sleeve for trapping any abrasive particles from Single seal Double seal
the seal face. Contamination of the medium in MXS184L MXS184L-D
the container is thus ruled out. The sleeve can be Single seal with integrated floating bearing. Double seal with integrated floating bearing
cleaned through a flushing bore. These seals are designed to be self-closing on
MXS154 the product side, i.e. they will remain closed even
Please note: diameters (d2 to d 5) increase to the All types of the MXS184 range available for unsteped with pressure variations or a pressure reversal.
next possible design size. shafts (all diameters). Seal identification: MXS154 ... Operation is optionally the same as for the single
Customized design or e.g. different drives (torque version. In view of the mechanical seal on the
transmissions) are available. atmosphere side it can be used as a buffer
MXS164 / 194 pressurized double seal . The barrier pressure
For glass-lined vessels. Dimensions as U164 should be 0.5 … 1.0 bar (7.25 … 15 PSI) above
pressure to be sealed.
Dimensional Data
Dimensions in millimeter
d1 (mm) d1 (inch) d2 d3 d4 d5 l2 l3 a 1(min) a 1 (max) s
25 1.000 34 68 - 148 41.5 40.5 100 132 11
28 1.125 34 68 55 148 41.5 40.5 100 132 11
30 - 34 68 55 148 41.5 40.5 100 132 11
32 1.250 39 73 60 153 41.5 40.5 105 137 11
35 1.375 39 73 60 153 41.5 40.5 105 137 11
38 1.500 44 78 65 158 41.5 40.5 110 142 11
40 - 44 78 65 158 41.5 40.5 110 142 11
45 1.625 49 83 68 163 41.5 40.5 115 152 11
- 1.750 49 83 68 163 41.5 40.5 115 152 11
48 1.875 54 88 73 178 41.5 40.5 125 160 14
50 - 54 88 75 178 41.5 40.5 125 160 14
55 2.000 59 93 78 183 41.5 40.5 130 165 14
- 2.125 59 93 78 183 41.5 40.5 130 165 14
60 2.250 64 98 85 183 41.5 40.5 135 170 14
65 2.375 69 103 90 193 44.5 40.5 140 175 14
- 2.500 69 103 90 193 44.5 40.5 140 175 14
70 2.625 74 108 95 198 44.5 43.5 145 180 14
- 2.750 74 108 95 198 44.5 43.5 145 180 14
75 2.875 79 113 100 203 44.5 43.5 150 185 14
80 3.000 84 118 105 208 44.5 43.5 155 190 14
85 3.250 89 123 110 213 44.5 43.5 160 195 14
90 3.500 94 128 115 218 44.5 43.5 165 200 14
95 3.750 99 133 120 223 44.5 43.5 170 205 14
100 - 104 138 125 228 44.5 43.5 175 210 14
105 4.000 109 143 130 233 44.5 43.5 180 215 14
110 4.250 114 148 135 238 44.5 43.5 185 220 14
115 4.500 119 153 140 267 44.5 43.5 196 243 18
125 4.750 129 163 150 277 44.5 43.5 206 253 18
140 5.000 144 178 165 297 44.5 43.5 221 273 18
- 5.250 144 178 165 297 44.5 43.5 221 273 18
- 5.500 144 178 165 297 44.5 43.5 221 273 18
150 5.750 154 188 175 307 44.5 43.5 231 283 18
160 6.000 164 198 185 317 44.5 43.5 241 293 18
- 6.250 164 198 185 317 44.5 43.5 241 293 18
MXS164 - Dimensions in millimeter
d 31) d 71) d1 nxd 2 d4 d0 k L1 L2 L w2) l1 l2 A M1 M1 A, B
40 38 175 4x18 110 90 145 87 136 143 15 28 122 M12 M16 G3/8
50 48 240 8x18 176 135 210 89 149 148 17 28 157 M12 M16 G3/8
60 58 240 8x18 176 135 210 93.5 156 158 17 28 168 M12 M16 G3/8
80 78 275 8x22 204 155 240 104.5 189 168 20 34 203 M16 M20 G1/2
100 98 305 8x22 234 190 270 109 190 178 20 34 228 M16 M20 G1/2
125 120 330 8x22 260 215 295 110 205 203 20 40 268 M20 M20 G1/2
140 135 395 12x22 313 250 350 124 222 208 20 40 285 M20 M20 G1/2
160 150 395 12x22 313 265 350 127.5 219.5 213 25 40 297 M20 M20 G1/2
180 170 445 12x22 364 310 400 132.5 230 233 25 45 332 M24 M20 G1/2
200 190 445 12x22 364 310 400 137.5 237.5 243 25 45 352 M24 M20 G1/2
220 210 505 16x22 422 340 460 149.5 249.5 263 25 50 381 M24 M20 G1/2
1) Shaft diameters d3 and d7 to DIN 28154
2) Shaft step to DIN 28154
inch size available from size 1.500 to 6.500
Note: Additional technical & dimensional information will be provided on request.
76
 U164 Single & Dual Seals Glass Lined Agitator Seals - Liquid Lubricated

Product Description Technical Features

1. Single and Dual seal configuration 1. Available with or without floating
2. Unbalanced design bearing
3. Independent of direction of rotation 2. Double seals can be applied at higher
4. Cartridge construction pressure and rotating speed
5. Designed for top entry vessels 3. Suitable for standardizations
6. Rotary unit with multiple springs 4. Rugged design to ensure long term
7. Construction with integrated bearing reliability and operating life
also available 5. Seals are assembled in cartridge
8. For glass-lined vessels, design construction for easy fitment
according to DIN 28138 T2 6. Over all connecting dimensions are
tailor made to customer's specifications
7. The seal design is unique as it closes
due to the hydraulic product pressure
as well as overlaying barrier pressure

Typical Industrial Applications

Chemical industry
Non-toxic media with single seal
d7 h6 Pharmaceutical industry

l3
Toxic media with double seal
Agitators
Reactors
Materials
According to application and customer's
2xM1 specification.
l2

G Performance Capabilities
13 C Sizes: d3 = Upto 160 mm (Upto 6.500’’)
12
1 Pressure: p1 = vacuum ... 16 bar (232 PSI),
L2

6
B
p3 = max. 18 bar (261 PSI)
Temperature: t1 = -40 °C... +200 (250) °C
d3 h 8
(-40 °F ... +392 (482) °F)
L1

l5

7
Speed = 0 ... 5 m/s (0 ... 16 ft/s)
A 2 Installation, Details, Options
14
2xM 2 nxd 2
11 F, G
15
l4
l1

M1
A B
7

C D
±0.1

M2
15

d8
E, G, T
d4 H8
f8 Supply connections
k1
Designation and positions of screwed connections,
pull-off and jacket threads acc. to DIN 28138 T3.
d1

A Barrier fluid resp. quench IN

Note: The item numbers as depicted above are based on our technical experience and B Barrier fluid resp. quench OUT
knowledge and are placed in the chronological order of their assembly procedure.
C Drainage
D Leakage drain G1/8"
d2 d5 2xM2
Item Description E Cooling IN G3/8"
l1

1 Seal face, atmosphere side F Cooling OUT G3/8"

7

G Grease
1.5
20 ± 0.1

30 0
2 Seal face, product side
1

6,7,13 O-ring d8 H Temperature metering

d6
14,15 k2

d4
11 Seat, product side
k1

12 Seat, atmosphere side d1

Flange connections acc. to DIN 28137 T2 for nominal

diameters 125 ... 161.

77
 Standards Notes
FDA Options:
DIN 28136 T3 (for glass-lined vessels) Cooling or heating flange
DIN 28137 T2 (flange connection for glasslined vessels) Leakage drain, flush or heating flange
DIN 28159 (shaft end for glass-lined vessels) Leakage drain or flush
Polymerization barrier, leakage drain or flush

Torque Transmissions

Clamping set Shrink disk Clamping ring Clamping ring

with pin

Installation, Details, Options

E
D
ls

l5

F
E D
F D

Option Option Option Option

Cooling flange, can be used Leakage drain, can be used Leakage drain, can be used Polymerization barrier, can be
alternatively as a heating flange alternatively as a flush or as a heating alternatively as a flush used alternatively as a leakage
(tmax. = 350°C (662 °F)). flange. drain or a flush.

Design Variations
Double Seals Variants
U164K-D
Double seal
U164KL-D
Double seal with integrated floating bearing
U156K(L)-D
Double seal with/without floating bearing for PN 25

Dimensional Data
Dimensions in millimeter

d 31) d 7 1) Nominal Flange size 2) d1 nxd 2 d4 nxd 5 d6 d8 k1 k2 L1 L2 l1 l2 I3 l4 l5 M1 M2 A,B

size
40 38 40 E125 175 4X18 110 - - 102 145 - 107 156 25 35 28 50 50 M12 M16 G3/8
50 48 50 E200 240 8X18 176 - - 138 210 - 107 167 25 40 28 50 50 M12 M16 G3/8
60 58 60 E250 275 8X22 204 - - 188 240 - 116 175 30 42 28 50 60 M12 M20 G3/8
80 78 80 E300 305 8X22 234 - - 212 270 - 125 206 30 45 34 60 60 M16 M20 G1/2
100 98 100 E400 395 12X22 313 - - 268 350 - 125 206 30 52 34 60 60 M16 M20 G1/2
100 98 100 E500 395 12X22 313 - - 268 350 - 125 206 30 52 34 60 60 M16 M20 G1/2
125 120 125 E700 505 4X22 422 12X22 320 306 460 350 133 226 30 75 40 60 80 M20 M20 G1/2
140 135 140 E700 505 4X22 422 12X22 320 306 460 350 144 242 30 79 40 60 80 M20 M20 G1/2
160 150 160 E700 505 4X22 422 12X22 320 306 460 350 151 242 30 77 40 60 85 M20 M20 G1/2
160 150 160 E900 505 4X22 422 12X22 320 306 460 350 151 242 30 77 40 60 85 M20 M20 G1/2
160 150 161 E901 565 4X26 474 12X22 370 356 515 400 151 242 30 77 40 60 85 M20 M20 G1/2
1) Shaft diameters d 3 and d 7 to DIN 28159
2) Flange size to DIN 28137T2
inch size available from size 1.575 to 6.500
Note: Additional technical & dimensional information will be provided on request.

78
 U184 Single & Dual Seals Agitator Seals - Liquid Lubricated

Product Description Technical Features

1. Single and Dual seal configuration 1. Available with or without floating
2. Unbalanced design bearing
3. Independent of direction of rotation 2. Double seals can be applied at higher
4. Cartridge construction pressure and rotating speed
5. Designed for top entry vessels 3. Suitable for standardizations
6. Rotary unit with multiple springs 4. Rugged design to ensure long term
7. Construction with integrated bearing reliability and operating life
also available 5. Seals are assembled in cartridge
construction for easy fitment
6. Over all connecting dimensions are
tailor made to customer's specification
7. The seal design is unique as it closes
due to the hydraulic product pressure
as well as overlaying barrier pressure

Typical Industrial Applications

a
Agitators
Chemical industry
Non-toxic media with single seal
d7 1) h 6 Pharmaceutical industry

l2
Reactors
Toxic media with double seal
Performance Capabilities
DIN 28138 T2
Sizes: d3 = 40.... 220 mm (1.575"....8.625")
2xM1 Single seals:
G
l2

Pressure: p1 = vacuum ... 6 bar (87 PSI),

C p3 = pressure less
34
Temperature: t1* = -40 °C ... +150 (250) °C
L2

B (- 40 °F ... +302 (482) °F)

Double seals:
Lw

Pressure: p1 = vacuum ... 16 bar (232 PSI),

L1

p3 = max. 18 bar (261 PSI)

A 6
Temperature: t1* = -40 °C ... +200 (350) °C
2xM 2 2 d2 (- 40 °F ... +392 (662) °F)
14
Speed = 0 ... 5 m/s (0 ... 16 ft /s)
* Higher or lower temperatures on request.
11
l1

15 Standards
FDA
1.5

DIN 28136 T2 (for steel vessels)

8.5

30
d 31) h8
DIN 28141 (flange connection for steel vessels)
0

d0 DIN 28154 (shaft end for steel vessels)

d 4 e8 Notes
k Options:
d1
Cooling or heating flange
Leakage drain, flush or heating flange
Note: The item numbers as depicted above are based on our technical experience and Leakage drain or flush
knowledge and are placed in the chronological order of their assembly procedure. Polymerization barrier, leakage drain or flush

Torque Transmissions

Clamping set Shrink disk Clamping ring Clamping ring

with pin

79
 Installation, Details, Options

Supply connections
Designation and position acc. to DIN 28138 T3.
F, G For reasons of standardization,
A Barrier fluid resp. quench IN
B Barrier fluid resp. quench OUT the supply connections of
C Drainage single seals are matched to
A M1 D Leakage drain G1/8" those of the double seals (in
B deviation from DIN 28138 T3).
C E Cooling IN G3/8"
D
S F Cooling OUT G3/8"
M2 G Grease
S Flush
E, G, T T Temperature metering

E
D
ls

l5

F
E D
D
F

Option Option Option Option

Cooling flange, can be used Leakage drain, can be used Leakage drain, can be used Polymerization barrier, can be
alternatively as a heating alternatively as a flush or as a alternatively as a flush. used alternatively as a
flange (tmax. = 350oC (662oF). heating flange. leakage drain or a flush.

Design Variations
Single Seals Variants Double Seals Variants
U184K U184K-D
Single seal Double seal
U184KL-D
U184KL Double seal with integrated floating bearing.
G
Single seal with integrated floating bearing. These seals are designed to be self-closing on
13
12
C
Operation of single seals only with pressure less the product side, i.e. they will remain closed even
1
6
B
quench. with pressure variations or a pressure reversal.
Operation is optionally the same as for the single
A version
7
2 (pmax = 6 bar (87 PSI) or
14
11 pmax = 6 bar at p1 > p 3 ).
15 In view of the mechanical seal on the
atmosphere side it can be used as a buffer
U154 pressurized double seal
All types of the U184 range available for unstepped shafts (all diameters). p1 = 16 bar (232 PSI).
Seal identification: U154... Customized design or e.g. different drives
(torque transmissions) are available.
Dimensional Data
Dimensions in millimeter
d 31) d 71) d1 nxd 2 d4 d0 k L1 L2 L w 2) l1 l2 a M1 M2 A, B
40 38 175 4X18 110 90 145 87 136 143 15 28 122 M12 M16 G3/8
50 48 240 8X18 176 135 210 89 149 148 17 28 157 M12 M16 G3/8
60 58 240 8X18 176 135 210 93.5 156 158 17 28 168 M12 M16 G3/8
80 78 275 8X22 204 155 240 104.5 189 168 20 34 203 M16 M20 G1/2
100 98 305 8X22 234 190 270 109 190 178 20 34 228 M16 M20 G1/2
125 120 330 8X22 260 215 295 110 205 203 20 40 268 M20 M20 G1/2
140 135 395 12X22 313 250 350 124 222 208 20 40 285 M20 M20 G1/2
160 150 395 12X22 313 265 350 127.5 219.5 213 25 40 302 M20 M20 G1/2
180 170 445 12X22 364 310 400 132.5 230 233 25 45 332 M24 M20 G1/2
200 190 445 12X22 364 310 400 137.5 237.5 243 25 45 352 M24 M20 G1/2
220 210 505 16X22 422 340 460 149.5 249.5 263 25 50 381 M24 M20 G1/2
1) Shaft diameters d 3 and d 7 to DIN 28154
2) Shaft step to DIN 28154
inch size available from size 1.500 to 8.625
Note: Additional technical & dimensional information will be provided on request.

80
 BSH-D Dual Seals Agitator Seals - Liquid Lubricated

Product Description Technical Features

1. Dual seal configuration 1. Over all connecting dimensions are
2. Balanced design tailor made to customer's specifications
3. Independent of direction of rotation 2. Specially designed to handle high
4. Cartridge construction operating pressure
5. Designed for top entry vessels 3. The seal design is unique as it closes
6. Rotary unit with multiple springs due to the hydraulic product pressure
7. Integrated bearing construction as well overlaying barrier pressure
available on request 4. Rugged design to ensure long term
reliability and operating life
5. Seals are assembled in cartridge
construction for easy fitment

Typical Industrial Applications

Chemical industry Dryers Standards
Pharmaceutical industry Mixers FDA
Suitable for all media Filter
Agitators Special rotating Notes
equipment Options:
Performance Capabilities Cooling or heating flange
G Leakage drain, flush or heating flange
Shaft diameter: dw = 20... 400 mm (0.79"...15.75") Leakage drain or flush
C
13
12 Pressure: p1 = vacuum ... 250 bar (... 3,625 PSI)*, Polymerization barrier, leakage drain or flush
1 B p3 = p1 + 10 %
4
Temperature: t = –40 °C... +200 (350) °C
(– 40 °F ... +392 (662) °F) Product variants
5
Sliding velocity: vg = 0 ... 5 m/s (0 ... 16 ft/s) Double seal variants
A 2
For application beyond this range, please BSH(V)-D
11
enquire. Double seal
14
BSH(V)L-D
Materials Double seal with integrated floating bearing
According to application and customer's (axial thrust bearing on request).
specification
Item Description Torque Transmissions
1 Seal face, atmosphere side
2 Seal face, product side
4, 5, 13, O-ring
14
11 Seat, product side
12 Seat, atmosphere side Clamping set Shrink disk Clamping ring Clamping ring
with pin
Installation, Details, Options

G, F

E
D
ls

l5

F
A E D D
B F
C
D
S
Option Option Option Option
Cooling flange, can be used Leakage drain, can be used Leakage drain, can be used Polymerization barrier, can be
G, E alternatively as a heating alternatively as a flush or as a alternatively as a flush. used alternatively as a
Supply connections flange (tmax. = 350°C (662 °F). heating flange. leakage drain or a flush.
A Barrier fluid IN
B Barrier fluid OUT
C Drainage
D Leakage drain G1/8"
E Cooling IN G3/8"
F Cooling OUT G3/8"
G Grease
S Flush

81
BSHLU-D Dual Seals Agitator Seals - Liquid Lubricated

Product Description Technical Features

1. Dual seal configuration 1. Over all connecting dimensions are
2. Balanced design tailor made to customer's specifications
3. Independent of direction of rotation 2. Specially designed to handle high
4. Cartridge construction operating pressure
5. Designed for bottom entry vessels 3. Product side is equipped with floating
6. Rotary unit with multiple springs throttle bush
7. Construction with integrated bearing 4. The seal design is unique as it closes
due to the hydraulic product pressure
as well overlaying barrier pressure
5. Rugged design to ensure long term
reliability and operating life
6. Seals are assembled in cartridge
construction for easy fitment

Typical Industrial Applications

Chemical industry
Suitable for all media
30 Agitators
Performance Capabilities
14 Shaft diameter: d w = ... 400 mm ( ... 15.75")
11 Pressure: p1 = vacuum … 60 bar (870 PSI)
2 Temperature: t = -40 °C ... +200 °C (-40 °F ... +392 °F)
5 Sliding velocity: vg = 0 ... 5 m/s (0 ... 16 ft /s)
For applications beyond this range, please enquire.
Materials
4 According to application and customer's
1 specification
Notes
12 Options:
13
S B Cooling or heating flange
Leakage drain, flush or heating flange
Leakage drain or flush
C A
G Item Description
1 Seal face, atmosphere side
2 Seal face, product side
4, 5, 13, O-ring
14
11 Seat, product side
12 Seat, atmosphere side
30 Throttle ring

Installation, Details, Options

G

E
D
ls

l5

F
A E D D
C B F

Option Option Option Option

Cooling flange, can be used Leakage drain, can be used Leakage drain, can be used Polymerization barrier, can be
G alternatively as a heating alternatively as a flush or as a alternatively as a flush. used alternatively as a
Supply connections flange (tmax. = 350°C (662 °F). heating flange. leakage drain or a flush.
A Barrier fluid IN
B Barrier fluid OUT
C Drainage
G Grease
S Flush

82
 Agitator Seals Accessories Optional Extras

Additional Options Shut-Down Seal (Vessel Containment)

D
E d1 max
F
l5

l - 0.2
P4

b
D d
d3
o
Cooling flange tmax = 350 C Leakage drain
(can also be used as a heating flange) (can also be used as a flush)
Rt < 5

STD1
If an STD is employed, it is possible to change seals with the
D
vessel loaded and under pressure (shaft must be
l5

E
F stationary!) This seal is only used if the product does not
Polymerization buffer
harden or congeal during the shut down period. It cannot be
Leakage drain and cooling flange
(can also be used as a used if PTFE is required or for sterile operation (fermenting
leakage drain of flush)
vessels). Can be installed in all aspects. Fitting dimensions
in accordance with DIN 28138 Part 1 are possible.
Types Of Drive Typical Industrial Applications
Chemical industry
Pharmaceutical industry
Agitators
Marine

Clamping set Operating limits d3 D d d1 1 b

d w = 40... 200 mm 40 76 42 .5 42 38 .0 8
16".. 8" 50 84 52.5 52 38 .0 8
p1 =16 bar (232 PSI)
60 95 62 .5 62 44 .5 10
t =100°C (212 °F)
Clamping ring with pin Elastomer sealing 80 118 82 .5 82 45 .0 10
element (Item no. 1) 100 138 102 .5 102 45 .0 10
with pneumatic or 125 160 127 .5 127 45 .0 10
hydraulic actuation 140 180 143 .5 143 50 .0 12
(closing pressure 160 200 163 .5 163 50 .0 12
P4 > P1). 180 215 183 .5 183 50 .0 12
Shrink disk
200 240 203 .5 203 50 .0 12

Clamping ring Screwed Connections

Extract or thread
Code System For DIN Seals G, F

. . . . . - . . ./ dw - ..
Type
300

A M1 a B
U Customer-
MXS C D
specification
GSAZ M2
Shaft
Range diameter
(U184... 56) G, E
1) Features Additional options Jacking thread
K = Internally balanced 0- basic design Extract or thread segment
(pressure from the inside) 1- leakage drain
L = with bearing 2- cooling flange Designation and position in accordance with DIN 28138 T3.
F = pumping screw
U = for bottom entry 4 - leakage drain + cooling flange
A = Buffer fluid resp. quench IN
Type Drive B = Buffer fluid resp. quench OUT
D = double seal 1- set screw C = Drainage
2- shrink disk D = Leakage drain G1/8"
1) If several features apply, the code letters are 3- clamping collar E = Coolant IN G3/8"
listed one after the other. 4- key F = Coolant OUT G3/8"
N.B.: The code system published in DIN 28138 5- flange (shaft sleeve) G = Grease point
Part 3 can also be used to describe and order
DIN agitator seals. 6- shaft sleeve with flange and key
7- clamping set
8- muff coupling
9- customer-specification
83
BFS6000 Thermosiphon – Seal Supply Systems

Product Description Technical Features

Circulation in accordance with API 682 / ISO 1. For optimum and simple cleaning of the
21049: Plan 52, Plan 53A vessel interior, a design variant is
The BFS6000 range of vessels range conforms available which can be dismantled
to API 682 guidelines. The vessels are 2. Modular design combination available
equipped with all essential connections for with a wide variety of system
fitting additional components. The BFS 6000 components and instruments selection
system is available in standard sizes with flat possible, such as level switch,
ends, sight-glasses for level monitoring and circulation pump, hand refill pump,
with or without cooling coil. BFS 6000 system is thermometer, base frame etc.
equipped as a standard with all the necessary 3. Construction of the BFS 6000 is
SYSTEM

FABR.

YEAR
NO.

MANUFOF

SHELL
seal.tech

ACTUR
TYPE

E
se
alm
Sealm
atic ati
India
Pvt
c
Ltd.
OPERA
®

TEMPETING
CE
system connections and brackets. designed for demanding operating
conditions up to 50 bar / 200°C
VOLUM
OPERA RATUR
E PRESS TING E
URE
DESIGN
TEMPE
RATUR
DESIGN E
PRESS
URE

4. Optimum visual is achieved for level

monitoring through a robust design with
weld-pad type sight glass

Typical Industrial Applications Standards

N9
6 5 3
Refining technology PED 2014/68/EU
2 4
Oil and gas industry ASME VIII, Div. 1
Chemical industry
Petrochemical industry
Thermosiphon System (API Plan 52) Functional Description
663 ± 20 Item Description The BFS system performs all the basic functions of a
247 ± 10
1 Level switch buffer/barrier system for the operation of double seals:
N4
 to pressurize the buffer chamber
N5 2 Manometer  leakage compensation
3 Manifold  buffer/barrier fluid is circulated by thermosiphon effect
5 1 4 Pressure switch  or forced circulation system
 to cool the seal
1465 ± 25

5 Shut-off valve
 to selectively absorb product leakage and prevent dry
N2
6 Orifice  running (tandem arrangement)
N3
Use compressed air or nitrogen for pressurization;
pressurization is monitored by a pressure switch.
972 ± 20

Ø 219.1 The incorporated level switch issues a signal whenever

N1
the level of buffer/barrier fluid is too low.
687 ± 15

Installation, Details, Options

342 ± 10

Operating and installation diagram

for a BFS6000 system.
5
The BFS vessel must always be
N7 N8 installed higher than the
N6 PI mechanical seal. The
PS buffer/barrier fluid flows via the
return pipe into the vessel and is
cooled. The exchange of fluid takes
Thermosiphon System (API Plan 52) place by the thermosiphon
LS
Item Description principle or by forced circulation,
N1 to the mechanical seal e.g. with a pumping screw.
LS Connection pipes to the seal
N2 from the mechanical seal
N3 Level switch
should be designed with as little
resistance as possible.
N4 Level switch
1 ... 2 m

N5 Filling connection
Bottom
N6 Drain
N7 Cooling water IN
N8 Cooling water OUT
Cover
N9 Connection to flare
Mechanical seal

84
 BFS1016 Thermosiphon – Seal Supply Systems

Product Description Technical Features

Circulation in accordance with API 682 / ISO 1. Available with or without cooling coil
21049: Plan 52, Plan 53A 2. All connections of the systems are
BFS1016 system is employed for applications side faced
in sealing systems with a wide variety of 3. Compact design of the system allows
operati ng param eters for s uppl y i ng low space requirements
buffer/barrier fluid to double and tandem 4. Modular design combination available
mechanical seals. The BFS1016 system is with a wide variety of system
available in standard sizes with flat ends, components and instruments selection
sight-glasses for level monitoring and with or possible such as, level switch,
seal.t
ech se
alm
without cooling coil. BFS1016 system is circulation pump, hand refill pump,
equipped as a standard with all the necessary thermometer, base frame etc.
SYS Sea
TEM
TYP
lma
tic ati ®

FAB E Ind c ®

CE
R.
NO. ia Pvt
YEA Ltd
MANR OF .
UFA
CTU OPE
SHE RE TEMRAT
LL
VOL PERING
UME OPE ATU
PRERAT RE
SSUING
DES RE
TEMIGN
PER

system connections and brackets. 5. Design allows for varied applications

ATU
DES RE
IGN
PRE
SSU
RE

due to construction in stainless steel

with borosilicate sight-glasses

X Z Typical Industrial Applications

276 Chemical industry

Ø 159
Petrochemical industry
Pulp and paper industry
1 Food processing industry
2 Water and waste water technology
60
150

20
Functional description
The BFS system performs all the basic functions of
a buffer/barrier system for the operation of double
100

seals:
43
485

 to pressurize the buffer chamber

X  leakage compensation
90

 buffer/barrier fluid is circulated by thermosiphon

10 effect or forced circulation system
Ø 14  to cool the seal
6
 to selectively absorb product leakage and
prevent dry running (tandem arrangement)
Use compressed air or nitrogen for pressurization.
60

7
Standards
8 4 3 5 9 PED 2014/68/EU (Design and production in
Z accordance with EU Pressure Equipment
Directive)
Installation, Details, Options
Operating and installation diagram for a BFS1016
7 system.
N2
The BFS vessel must always be installed higher
Item Description 1 6 than the mechanical seal. The buffer/barrier fluid
flows via the rising pipe into the vessel and is
1 Buffer/barrier fluid IN (G1/2") cooled. Particularly with natural circulation, the fluid
2 Buffer/barrier fluid OUT (G1/2") level must always be higher than the rising pipe to
5 maintain the circulation and to provide the specified
3 Cooling water IN (pipe 12 x 1.5 mm)
cooling capacity. Connection pipes to the seal
4 Cooling water OUT (pipe 12 x 1.5 mm) should be designed with as little resistance as
2
5 Filling connection with cap (G1/2") possible.
6 Pressure gas connection (1/4" NPT) 1 Pressure gauge
1 ... 2 m

4
7 Connection for level switch (G2") 2 Thermometer
8 Connection for refill unit (G1/8") 3 Mechanical seal
4 Circulating Pump
9 Connection for pressure gauge (1/4"NPT) 5 Hand Refill Pump
3
10 Bracket for refill unit 6 From PCV, we recommend using a reverse
controlled pressure control valve (PCV)
7 Level switch

85
 Technical Features

Designation BFS1016

Pressure Equipment Directive PED

Integrated cooling coil Yes

Volume of vessel (litres) 8
Volume of tube (litres) 0.2
1)
Allowable pressure 16 bar (232 PSI)

Allowable temperature1) –60 °C ... +200 °C (–76 °F ... +392 °F)

Working volume, MAX-MIN (litres) 1.3

Cooling capacity – without cooling water (kW) 3) 0.3

2)
Cooling capacity – natural circulation (kW) 1.2
2)
Cooling capacity – forced circulation (kW) 2.5

Required cooling water quantity (m3/ h) 0.3

Metal parts 1.4571

Sight-glass Reex sight-glass Borosilicate

Seal PTFE

Other versions on request.

1)
Design data, permissible working values depend on the actual conditions of service
2)
Guidelines with buffer/barrier fluid water 60 °C – cooling water 20 °C
3)
Guidelines with buffer/barrier fluid water 60 °C – ambient temperature 20 °C (valid for thermosiphon systems without cooling water
with natural circulation resp. forced circulation)

86
 PBS2000 Pressure Booster – Seal Supply Systems

Product Description Technical Features

Circulation in accordance with API 682 / ISO 1. Simple and reliable operation is achieved due to
21049: Plan 53C automatic setting of the barrier pressure
PBS system is employed for applications in through reference pressure
sealing systems with a wide variety of 2. Barrier pressure is achieved without any need
operating parameters for supplying quench for connection to a nitrogen supply source
buffer fluid to double and tandem mechanical 3. Hassle free maintenance of simple and quick
seals. PBS system is equipped as a standard cleaning is achieved in operation as the housing
can be dismantled
with all the necessary system connections
seal.te
seal 4. Modular design combination available with a
and brackets. Modular design combination
ch

SYST
EM
Sea
lma mat
TYPE tic
Indi ic ®

CE
FABR a Pvt
. NO.
YEAR
Ltd.

wide variety of system components possible

MAN OF
UFAC OPER
SHEL TURE TEM ATIN
PERA G
L VOLU OPER TURE
ME PRES ATIN
SUR G
DESI E

available with a wide variety of system

TEM GN
PERA
TURE
DESI
GN
PRES
SUR
E

5. Optimum level of monitoring is achieved due to

components. the protective pipe made in borosilicate glass
The maximum operating pressure of the PBS 6. Safe operation even in case of pressure
system applies to the housing of the pressure changes
booster, i.e. the process/medium pressure at 7. Sockets are designed with recessed gasket to
the connection must be lower and is avoid contamination of the circuit by thread
conditional on the transmission ratio sealant

239 Recommended applications Functional Description

MIN Refining technology The function of the PBS system is similar in principle
Oil and gas industry to the BFS system. The difference is that the
D Chemical industry
240

barrier pressure is created by the reference

204 Petrochemical industry pressure without any additional superimposition of
MAX E
13

nitrogen. The pressure booster is for storing and

6
30

F Standards cooling the barrier fluid. Pressurization is by means

A of a piston in dependency on the process/medium
PED 2014/68/EU (Design and production in
pressure. Automatic pressure increase in
Ø 14 accordance with EU Pressure Equipment
15

accordance with the transmission ratio.

65

Ø 168.3
Directive) ASME VIII, Div. 1
~815

(Design, calculation and production)

Installation, Details, Options

Operating and installation
diagram for a PBS system.
The PBS pressure
booster must always be
installed higher than the
mechanical seal. The
contact unit
barrier fluid flows via the
60

Measuring unit return pipe into the vessel

B C and is cooled. The
E
exchange of fluid takes
place by the
Hand thermosiphon principle or
Barrier medium IN (G1/2")
Refill by forced circulation, e.g.
A Pump with a pumping screw.
connection possible for Measuring unit
Connection pipes to the
1 ... 2 m

B Barrier medium OUT (G1/2") seal should be designed

C Process medium (G1/2") with as little resistance as
possible.
D Coolant IN (tube 15 x 1.5)
E Coolant OUT (tube 15 x 1.5)
Product pressure
F Connection for HRP (G1/8")

Circulating Pump

Mechanical seal

87
 Technical Features

Designation PBS2000
Pressure Equipment Directive PED
Integrated cooling coil Yes
Transmission ratio 1:1.1
Volume, jacket (litres) 4
Volume, cooling coil (litres) 0.7
Allowable pressure 1) 63 bar (913 PSI)
Allowable process/medium pressure at connections C 1) 57 bar (827 PSI)
Allowable working temperature 1) -60 °C ... +200 °C (-76 °F ... +392 °F)
Working volume, MAX-MIN (litres) 2
Cooling capacity – without cooling water (kW) 3) 0.5
Cooling capacity – natural circulation (kW) 2) 1.5
Cooling capacity – forced circulation (kW) 2) 4
Required cooling water quantity (m3/ h) 0.4
Metal parts 1.4571
Protective tube for piston rod Borosilicate
Seal PTFE
Net weight (approx.) 51 kg (112 lb)

Other versions on request.

1)
Design data, permissible working values depend on the actual conditions of service
2)
Guidelines with barrier fluid water 60 °C – cooling water 20 °C
3)
Guidelines with barrier fluid water 60 °C – ambient temperature 20 °C
(valid for pressure booster systems without cooling water with natural circulation resp. forced circulation)

88
 BFS2000 Thermosiphon – Seal Supply Systems

Product Description Technical Features

BFS 2000 system is employed for 1. Available with or without cooling coil
applications in sealing systems with a wide 2. Optimum draining and venting is
variety of operating parameters for supplying achieved because of the design of
buffer/barrier fluid to double and tandem cooling water connections at top (OUT)
mechanical seals. The BFS 2000 system is and bottom (IN)
available in standard sizes with flat ends, 3. Sockets are designed with recessed
sight-glasses for level monitoring and with or gasket to avoid contamination of the
without cooling coil. BFS 2000 system is circuit by thread sealant
equipped as a standard with all the necessary 4. Construction of the BFS 2000 is
system connections and brackets. Modular designed for demanding operating
design combination available with a wide conditions up to 30 bar / 200°C
variety of system components and 5. Design allows for varied applications
instruments selection possible such as, level due to construction in stainless steel
switch, circulation pump, hand refill pump, with borosilicate sight-glasses
thermometer, base frame etc.
Circulation in accordance with API 682 / ISO
21049: Plan 52, Plan 53A

9 5 7 6
Typical Industrial Applications
Chemical industry
Oil and gas industry
11 Petrochemical industry
Refining technology

Item Description Standards

427 ± 5
170
160

1 Buffer/barrier fluid IN (G1/2") PED 2014/68/EU (Design and production in

accordance with EU Pressure Equipment Directive)
2 Buffer/Barrier fluid OUT (G1/2") ASME VIII, Div.1 (Design, calculation and production)
1
3 3 Cooling water IN (G1/2") Functional Description
2
4 Cooling water OUT (G1/2") The BFS system performs all the basic functions of a
8
5 Filling connection with plug (G1/2") buffer/barrier system for the operation of double seals:
Ø 193.7 • to pressurize the buffer chamber
6 Pressure gas connection (G1/2")
• leakage compensation
170 7 Connection for level switch or level indicator (G2") • buffer/barrier fluid is circulated by
Ø 14 130
8 Connection for hand refill pump (G1/2") thermosiphon effect or external circulation system
10 • to cool the seal
4 9 Universal connection (G1/2") for safety valve, flare,etc.) • to selectively absorb product leakage and
258 ± 2

10 Bracket for hand refill pump prevent dry running (tandem arrangement)
11 Sight-glass • Use compressed air or nitrogen for pressurization.

Operating and Installation Schematic

2
The BFS vessel must always be installed higher
N2 than the mechanical seal. The buffer/barrier fluid
3
Technical Features flows via the return pipe into the vessel and is
cooled. The exchange of fluid takes place by the
Designation BFS2000
thermosiphon principle or by forced circulation,
Pressure PED 1
Equipment e.g. with a pumping screw. Connection pipes to
Directive the seal should be designed with as little
Integrated cooling Yes 4 resistance as possible.
coil
Volume, vessel 9 1. Measuring unit
(litres)
2. Level Switch
Volume, tube 0.5
(litres) 3. From PCV, we recommend using a reverse
1 ... 2 m

Allowable 30 bar
controlled pressure control valve (PCV)
pressure1) (435 PSI) 4. Hand Refill Pump
5. Circulating Pump
Allowable -60 ... +200 °C 6. Mechanical seal
temperature1) (-76 ... +392 °F) 5
Working volume, 1.8
MAX-MIN (litres)

Cooling capacity – 0.5

without cooling
water (kW)3)
6
1)
Higher values on request
2)
Other materials on request
3)
Valid for thermosiphon system without cooling water with natural circulation resp. forced circulation)

89
BFS 53B Closed Loop – Seal Supply Systems

Product Description Technical Features

Circulation in accordance with API 682 / ISO 1. Design construction available with
21049: Plan 53B finned tube, water or air coolers with fan
Pressurised barrier system (closed circuit) is 2. Barrier pressure is created without any
employed for applications in sealing systems need for connection to a nitrogen
with operating parameters of high pressures supply
and/or for hazardous/environmentally 3. Modular design combination available
harmful processes. The BFS (Plan 53B) with a wide variety of system
range is available with a pressure components and instruments selection
accumulator, cooler (finned tube or water or possible
air cooler with fan) with a wide range of 4. Pressurisation is achieved through a
instruments. pre-loaded bladder accumulator
5. Nitrogen cannot get into the barrier
medium or process medium, because it
is separated from the barrier medium by
membranes in the accumulator

Typical Industrial Applications

Chemical industry
Oil and gas industry
Petrochemical industry
Refining technology
Functional Description
The BFS is designed to perform the following
functions of a barrier system:
 to pressurize the barrier chamber
 leakage compensation
 to cool the seal
Pressurization (> process pressure) prevents the
process medium from getting into the barrier circuit or
the atmosphere. Pressurization is supplied by a
pressure accumulator which is pre-loaded with
nitrogen. Circulation in the barrier circuit takes place by
the thermosiphon principle or by forced circulation, e.g.
with a pumping screw.

Standards
PED 2014/68/EU (Design and production in
accordance with EU Pressure Equipment Directive)
ASME VIII, Div. 1 (Design, calculation and production)
Installation, Details, Options
Operating and installation diagram for a
BFS (Plan 53B).
A From mechanical seal
B To mechanical seal
C Fill
F Drain
G Vent
H N2 Precharge

C H
PIT

Optional

TI

Piping Tubing F

90
 BFS 54 Barrier Pressure Unit – Seal Supply Systems

Product Description Technical Features

BFS range of barrier pressure units are 1. For reducing barrier fluid pressure at
designed to perform various functions of a standstill an automatic relief valve is
barrier system which is essential for provided
operating double seals (circulation and 2. Reversible double filter is provided for the
cooling of the barrier medium, pressurisation fluid to pass through the oil cooler
of the barrier fluid and compensation of 3. Level Switch with contact for minimum level
leakage). The BFS systems are designed to 4. Barrier fluid pressure can be controlled
operate with hydraulic oil having viscosity manually
values ranging from 12 to 90 mm 2/s under 5. Maximum operating temperature in the tank
normal operating temperature of the to be maintained at 80 o C (return line
equipment. The final selection of optimum maximum 90 oC)
viscosity of the oil to be used has to be 6. For monitoring the pump discharge pressure
ascertained independently in accordance (outside the circuit) an additional pressure
with the respective operating parameters of connection is provided
the equipment. 7. Temperature monitoring is achieved by
providing a return line and tank thermometer

Typical Industrial Applications Technical Features

Chemical industry
Oil and gas industry Cooling
Petrochemical industry Nominal capacity
Refining technology pressure Flow (kW) Dimensions Net
Designation max. rate Tank weight Motor data
with overall (mm)
Functional Description Barrier (l/min) hydraulic approx.
pressure oil
The barrier pressure for circulation
∆t = 10K
is generated by a gear pump. The
setpoint barrier pressure is set on Nominal Circulation Height Width Depth Nominal
an overflow valve in the mechanical capacity volume power
seal return line. From this point on (litres) (litres) (kW)
the barrier fluid flows back without
BFS 54 40 bar 6 1.8 40 12 650 610 380 125 1
pressure through a filter and a heat
(580 PSI)
exchanger to the storage tank. To
enable systems (pump, agitator) to Higher values on request
be stopped without causing Other materials on request
damage to the seal in the event of a
malfunction (e.g. power failure,
damaged motor, etc.), the barrier
pressure unit can be fitted with a
pressure accumulator unit. To
prevent the pressure in the
accumulator discharging to the
pressureless storage tank, the
return line has a pilot-operated
check valve, and the supply line
also has a simple check valve. The
barrier pressure is retained for a
l i m i t e d t i m e . H o w e v e r, n o
circulation takes place and no heat
is dissipated from the mechanical
seal.
Installation, Details, Options
Mechanical seal

Pressure and
Safety temperature
valve measuring unit

Pressure Pressure
Accumulator Control
Unit Unit

Circulating
pump Filter

Heat
Tank exchanger

Installation and operating

diagram for a BFS system.

91
HED Heat Exchanger – Seal Supply Systems

Product Description Technical Features

Circulation in accordance with API 682 / 1. Cooling capacity up to 36 kW
ISO 21049: Plan 21, Plan 22, Plan 23, 2. Installation can be done either in a
Plan 41 vertical or a horizontal position
HED designed heat exchanger is 3. For optimum and simple cleaning, the
employed to cool process/barrier fluids in heat exchanger can be dismantled
seal supply systems. 4. Compact design of tubular heat
Construction of the vessel is in a tubular exchanger with integrated guide
design with integrated guide plates, the plates alongwith extremely efficient
process/barrier medium is directed cooling capacity
through the shell of the HED and the 5. Designed for varied applications due
cooling medium through the tubes. to construction in stainless steel
allows flush with a suitable solvent on
the process/barrier medium side

Holding device Typical Industrial Applications

and support 180 135 Chemical industry
as accessories Oil and gas industry
Offset Ø 3.5 Petrochemical industry
by 90o Power plant technology
Refining technology
N8 N7
Notes
N5 Cleaning:
N2 Cooling water side: the area around the tubes can
be cleaned mechanically after the housing is
removed.
Ø 125

Process/barrier medium side: flush with a suitable

solvent.
Standards
N1 PED 2014/68/EU (Design and production in
N6 accordance with EU Pressure Equipment
Directive)
ASME VIII, Div. 1 (Design, calculation and
N3 450
N4
production)

Technical Features
Designation HED Tubes Shell
Pressure Equipment Directive PED
Connections Allowable pressure1) 16 bar 130 bar
(232 PSI) (1885 PSI)
Item Description
Allowable temperature1) 150 °C
N1 Cooling water IN
75.5
100

(302 °F)
N2 Cooling water OUT
Inlet temperature2) 30 °C 65 °C
N3 Process/barrier medium IN (86 °F) (149 °F)

N4 Process/barrier medium OUT Flow quantity (m3/h)2) *) 1 approx. 0.5

N5 Cooling circuit vent Volume (litres) 0.23 1.4

N6 Cooling water drain 4 Cooling surface2) 0.2

Cooling capacity (kW)*) 6
N7/N8 Process/barrier circuit vent
Metal parts SS 316
Other versions on request.
80 O-rings FKM
1)
These values are based on the calculation of strength. Gaskets PTFE
2)
These values are based on the calculation of heat.
*)
Related to water on both sides Screws Stainless steel A4-70

92
 HE Heat Exchanger – Seal Supply Systems

Product Description Technical Features

Circulation in accordance with API 682 / ISO 1. Construction design for operating
21049: Plan 21, Plan 22, Plan 23, Plan 41 pressure up to 45 bar / 260°C (tube
HE designed heat exchanger is used to cool side)
process/barrier fluids in seal supply systems. 2. Design allows for varied applications
HE heat exchanger is available in standard due to construction in stainless steel
construction and conforms to API 682 3. For optimum and simple cleaning of the
standards. tubes, the heat exchanger can be
The process/barrier medium is directed dismantled
through the tube and the cooling medium 4. Complete venting and draining of the
through the shell. For simple draining or cooling water side and process can be
venting on the side of the cooling water, the achieved
heat exchanger can also be supplied with
ventilation/drainage ball valves. Temperature
instruments can also be fitted in the supply line
of the mechanical seals.

Typical Industrial Applications Notes

596 Chemical industry Cleaning:
471
78.3 78.3
N5
Oil and gas industry Cooling water side: the area around the tubes
Petrochemical industry can be cleaned mechanically after the housing is
N3 Refining technology removed. Process/barrier medium side: flush
Ø 219.1

N2
+15

with a suitable solvent.

405 -9

42

N1
Standards
229

N4
PED 2014/68/EU (Design and production in
N6 accordance with EU Pressure Equipment
Directive)
ASME VIII, Div. 1 (Design, calculation and
production)
Technical Features

Designation HE

Tube Shell
Pressure ASME
Equipment
Directive
For shaft x
diameters > 60
mm (acc. to API682)
Ball valve for -
draining on the
cooling water side

Connections 3/4" flange 3/4" NPT

Design 45 bar 16 bar
pressure1) (653 PSI) (232 PSI)
Design 260 °C 150 °C
temperature1) (500 °F) (302 °F)
Cooling capacity 6
(kW)*)

Metal parts 1.4404

O-rings FKM

Screws Stainless
steel A4-70
Other versions on request.
1)
These values are based on the calculation of strength.
*)
Related to water on both sides

93
 HEK Heat Exchanger – Seal Supply Systems

Product Description Technical Features

Circulation in accordance with API 682 / 1. Cooling capacity up to 10.5 kW
ISO 21049: Plan 21, Plan 22, Plan 23, 2. Cost effective solution
®
Plan 41 3. Effective cooling achieved with wound
atic

seal
.tech
se
alm
Fab
r. No
.
HEK designed heat exchanger is double helix around a guide tube
Typ

Ye

V
e

ar
employed to cool process/barrier fluids in 4. Designed for varied applications due
seal supply systems. The heat exchanger to construction in stainless steel
PB

TB

has a wound double helix around the 5. For optimum and simple cleaning, the
guide tube, the process/barrier medium is heat exchanger can be dismantled
directed through the shell of the HEK and
the cooling medium through the tubes.

From Seal To Seal Typical Industrial Applications

Chemical industry
Petrochemical industry
Power plant technology
Refining technology
Oil and gas industry
150
100

Cooling water Standards

IN OUT PED 2014/68/EU (Design and production in
accordance with EU Pressure Equipment Directive)

G½" Notes
Mount vertically with connections pointing up.
150
75
383
180

Provide for external venting on the process/barrier

100 medium side (the user has to install a vent at the
highest point of the pipe work).
Ø 13.5 Cleaning:
Cooling water side: the area around the tubes can be
cleaned mechanically after the housing is removed.
process/barrier medium side: flush with a suitable
solvent.

Technical Features

Ø 133 Designation HEK Tube Shell

Pressure Equipment Directive PED

Allowable pressure1) 120 bar 16 bar

(1740 PSI) (232 PSI)

Allowable temperature1) 160 °C 95 °C

(320 °F) (203 °F)

Inlet temperature2) 70 °C 25 °C
(158 °F) (77 °F)

Flow rate2) 10 l/min 1.8 m3/h

Volume (litres) 0.34 1.13
Cooling surface2) 0.3 m2
Cooling capacity (kW) 10.5
Metal parts SS 316 Carbon steel, primed on the outside
Seals FKM
Screws Stainless steel A4-70

Other versions on request.

1)
These values are based on the calculation of strength.
2)
These values are based on the calculation of heat.

94
 MS Magnetic Separator – Seal Supply Systems

Product Description Technical Features

MS range of separators consists of a 1. Construction design for operating
pressure casing with integrated magnetic pressure up to 150 bar
rod for high level of efficiency. MF filters 2. Hassle free maintenance of simple
are employed in seal supply systems and and quick cleaning is achieved in
any other such systems in which the operation as the housing can be
media has to be cleaned of magnetic dismantled
impurities up to a certain size 3. Reliability in operation due to rugged
technology

4 3 2 8 7 Typical Industrial Applications

Chemical industry
Oil and gas industry
Petrochemical industry
Power plant technology
Refining technology
Functional Description
The magnetic rod is positioned in the casing in
such a way that it catches magnetic particles
flowing past in the medium on all sides.
1 Operating and Installation Schematic
Cleaning:
The magnetic rod can be removed for cleaning
6 with the casing fitted by opening the cover (with
the line depressurized!).
Maintenance intervals depend on the degree of
118

soiling. We recommend checking and if

5 necessary cleaning the magnetic rod several
hours after using for the first time and each time
84

after flushing the pipes because experience

indicates that much of the dirt is flushed out of the
pipes at this time.

Item Description
30

1,2 Casing and cover

3 O-ring
4,8 Screws
5 Washers
M8 6 Ring magnets:
9 corrosion-resistant
7 Spring
Ø 92 8 Fixing hole

Technical Features
Description Connection Allowable pressure Allowable temperature Volume (litres) weight approx. Cover, housing Spring O-ring Gasket
MS G 1/2" 120 bar 160 °C 0.08 5.5 kg. Stainless Steel 1.4301 EPDM T2
(1,740 PSI) (320 °F) 12.2 lbs
1)
Higher values on request
2)
Other materials on request

95
MF Magnetic Filter – Seal Supply Systems

Product Description Technical Features

MF filters are inline filters for installation 1. All the parts exposed to pressure are
inside pipelines and are employed in seal constructed from forged material
supply systems and any other such 2. Combination device: magnetic filter and
systems in which the media has to be filter element
cleaned of magnetic and non-magnetic 3. Hassle free maintenance of simple and
impurities up to a certain size. High level of quick cleaning is achieved in operation
efficiency is guaranteed because of the as the housing can be dismantled
combination of magnetic rod and filter 4. Protection of filter elements from
element reverse current is achieved due to the
provision of internal mesh
5. Venting screws in the filter inlet and
outlet can be employed as connections
for maintenance or for indicating
differential pressure

13 Typical Industrial Applications

1 Chemical industry
Oil and gas industry
38

Petrochemical industry
Power plant technology
Refining technology
6
Functional Description
Overall height when dismantled ~ 350

The magnetic rod is positioned in the filter in such

a way that it catches magnetic particles flowing
3 past in the medium on all sides. Partial coarse
3a filtration is provided by the incorporated filter
element.
Item Description
1 Filter cover
2
2 Filter barrel
3 Element insert
3a Internal mesh
6 Ring magnet
13 Venting screw

Technical Features
1)
Designation Connection Allowable pressure Allowable temperature Filter grade Weight (approx.) Housing, filter head Filter insert, filter element2) O-ring Gasket

MF G 1/2" 63 bar 150 °C 50 µm 7.8 kg 1.4571 1.4301 FKM T2

(913 PSI) (302 °F) (17.2 lb)

1)
Higher values on request
2)
Other materials on request

96
 CS Cyclone Separator – Seal Supply Systems

Product Description Technical Features

Circulation in accordance with API 682 / 1. Construction design for operating
ISO 21049: Plan 31, Plan 41 pressure up to 200 bar
The CS range is available in varied 2. Hassle free maintenance is achieved in
versions i.e. cyclone separator with operation with high reliability, because
replaceable insert made of ceramic or cast the dirt is automatically conveyed to the
version of the cyclone separator or suction nozzle of the pump
cyclone separator for high flow rates and 3. High filtration efficiency
high pressures. 4. Compact design is achieved because
of low space requirement, in addition to
the option of block-type design with
integrated flange connections
5. Design allows for varied applications
due to construction in stainless steel
with replaceable insert made of ceramic

Ø 92 Typical Industrial Applications

Chemical industry
Oil and gas industry
Petrochemical industry
Refining technology
Water and waste water technology

Functional Description
2 Cyclone separators of the CS range are used to clean
mainly aqueous liquids containing dirt and solids (e.g.
4 in circulation systems of sewage, sludge or pipeline
pumps). The best possible filtration efficiency is
achieved when the specific weight of the solids is much
higher than that of the carrier liquid, and when the
differential pressure is as large as possible within the
permissible pressure range (min. 1.7 bar in
accordance with API 682). The viscosity of the medium
is also a factor that needs to be taken into account.

Operating and Installation Schematic

The cyclone separator must always be installed in the
vertical position. The pressure at the outlets (C) and (B)
135

must be lower than at the inlet (A). Cleaned liquid is

conveyed to the top (B) and the separated dirt to the
1 suction port of the pump.

3 B

CS Cyclone Separator
C
Item Description
1 Housing
2 Cover
3 Insert
4 O-ring

Technical Features
Allowable Allowable
Designation Insert Connections Connecting size Housing/cover O-ring
pressure1) temperature1)
CS Ceramic 64 bar (928 PSI) 125 °C (257 °F) G, R, NPT, Flange 1/2" 1.4571 FKM
1)
Higher values on request
2)
Other materials on request

97
HRP Hand Refill Pump – Seal Supply Systems
Product Description Technical Features
The hand refill pump consists of a storage 1. For efficient processes, with a choice of 2 basic
vessel with level indicator, filling filter and a types
hand pump with integrated check valve. It 2. For manual refilling of buffer fluid units during
is mounted directly on the thermosiphon operation
vessel or the pressure booster. 3. Designed for varied applications due to
construction in stainless steel with borosilicate
sight-glasses suitable for highly corrosive media
4. Reliability in operation due to the design of
combined filling and ventilation filter in the hand
refill pump
5. Two sight-glasses for reading the MIN/MAX fluid
level

Recommended applications Functional description

Chemical industry Refining technology The hand refill pump is designed for manual
Petrochemical industry Pulp and paper industry refilling during operation in case of buffer fluid
Oil and gas industry Food and beverage industry losses.
Product Variants
Allowable Material, sight- Material, filling Pressure
Designation Volume (litres)
temperature glass/seal filter control valve
Acrylic glass, Borosilicate, T2 Polyamide Stainless steel None 16 bar 30 bar 63 bar
Perbunan® (232 PSI) (435 PSI) (913 PSI)
60 °C
HRP 2 x x x
(140 °F)

Higher values on request

Other materials on request

98
 QFS2000 Quench Fluid Reservoir – Seal Supply Systems
Product Description Technical Features
Circulation in accordance with API 682 / ISO 1. Designed for varied applications due to
21049: Plan 51, Plan 52 construction in stainless steel with
Quench fluid supply system is employed for borosilicate sight-glasses suitable for
applications in sealing systems with a wide highly corrosive media
®

atic
sealtic m
India
Pvt Ltd.
seal.te
ch
Sealma

Type

Fabr no.
manu
f.
variety of operating parameters for supplying 2. Reliability in operation due to the design of
quench fluid to double and tandem mechanical combined filling and ventilation filter in the
l
Year of Vesse

e
Volum .
ting Press
Opera
max.
.

seals. They act as a convenient fluid reservoir. hand refill pump

ting Temp
Opera
allow

The exchange of fluid takes place by the 3. Construction design for operating
thermosiphon principle or by forced circulation, pressure up to 200 °C
for example with a pumping screw. The 4. Discharge of leakage is achieved due to
QFS2000 stainless steel tank is equipped with integrated overflow design
sight-glasses for monitoring the MIN/MAX level 5. To monitor the fluid volume a level switch
and can be fastened with a lug fixture. The can be installed instead of sight glass
leakage overflow can be selectively discharged.
C
Recommended applications Notes
+5
154
2 Chemical industry Rening technology Install the quench fluid tank approx. 1 ... 2 m (3.3
Petrochemical industry Pulp and paper industry ... 6.6 ft) above the mechanical seal. Install
5 40 Oil and gas industry Food and beverage industry connection pipes to the mechanical seal with low
3 Ø1
3
4 Ø 120 flow resistance. Pipes must vent automatically in
+ 10

Functional description the direction of the tank. It is imperative that air

358

80

3
Quench fluid systems are employed: pockets are prevented. The minimum filling level
B
 to absorb leakage must always be above the connection socket at
1 the side (in the case of the thermosiphon
80

 to monitor the leakage rate (e.g. through

periodic reading of the level in the tank) principle).
A  to lubricate and to cool the outboard Quench fluid systems can be operated in two
mechanical seal in a tandem arrangement different modes:
 to prevent icing Dead-end quench (Plan 51):
 to protect against dry running Quench fluid from an elevated tank. The
Item Description
 to stabilize the lubricating film characteristic feature of this principle is that no
Connections 1 Storage tank (capacity 3L)  to exclude air from the media in order to heat is dissipated by the system.
A To the mechanical seal 2 Inlet filter with vented cap prevent a reaction with oxygen in the air Circulation (Plan 52):
Quench fluid from an elevated tank; external tank,
B From the mechanical seal 3 Sight-glass or level switch
pressureless; thermosiphon or forced circulation.
C Filling 4 Name plate In this case heat is dissipated by the circulation.
5 Overflow G 1/8 Cooling capacity by convection is minimal,
Higher values on request
Other materials on request however.

98
 API 682 4th Edition Sealmatic Product Locator For Mechanical Seals

Category Category 1
Configura on 1CW‐FX 2CW‐CW 2NC‐CS 3CW‐FB 3NC‐BB

Sta onary Rota ng

Mechanical Seal

CTXAPI‐SN CTXAPI‐DN GSPH‐Ta CTXAPI‐DN GSPH‐KD

Seal Type A

Category Category 2 and 3

Configura on 1CW‐FL 2CW‐CW 2CW‐CS 2NC‐CS 3CW‐FB 3CW‐BB 3CW‐FF 3NC‐FB 3NC‐BB 3NC‐FF
Rota ng Sta onary Rota ng

B750VK‐
B750VN B750VK GSPH GSPH‐Ta B750VK B750VK‐D GSPH‐KD

Seal
Type A
SB SB‐Ta SB‐Ta SB‐D BGSR‐Ta GSR‐D
Mechanical Seal

Seal
UFL850 UFL850‐Ta UFL850‐Ta UFL850‐D
Type B
Sta onary Rota ng

UFLWT800‐
UFLWT800 UFLWT800‐Ta UFLWT800‐D
Ta
Seal
Type C
UFL650 UFL650‐Ta UFL650‐Ta UFL650‐D

th
API 682 4 Edition Code
Mechanical Seal Design Options Size Plans

Category Arrangement Type Containment Device Secondary Seal Material Face Material Shaft Size Piping Plan

I: FFKM (Inner position) N: Carbon vs Reaction

2 2 A P: Plain gland 050 02/52
F: FKM (Outer position) Bonded Silicon Carbide

Seal designa on: 22A‐PI/FN‐050‐02/52

99
 Technical Information

TTV O-rings Conical springs Types of drive Viscosity 

Double PTFE-encapsulated O-rings of When a conical spring is used for driving For a seal to function properly, the shaft Conversion table*
t h e t y p e u s e d i n S E A L M AT I C the seal (e.g. in standard types U200 and torque must be transmitted uniformly to The following conversion table shows
mechanical seals combine the elasticity U300), the mechanical seal becomes the shaft sleeve and/or rotating parts the kinematic viscosity n in terms of
of the core materials (synthetic rubber) dependent on the direction of under all operating conditions. conventional units of measurement at
with the chemical and thermal rotation. Looking toward the sliding face Depending on the seal design it is the same temperature.
resistance of the PTFE. The material of the rotating parts of the seal, shafts necessary to make allowance for
 °E R.I SU
PTFE features good chemical and rotating in clockwise direction require centrifugal and axial forces and in some mm2/s sec sec
right-hand springs and shafts rotating in case to observe special installation -
1.0 1.00 -
600 anti-clockwise direction require left-hand instructions. Incorrect fitting can cause, -
Coefficient of exp. 10-6 (1/ oC)

1.5 1.06 -
500 springs. Mounting the conical spring is for example, jamming and de-formation 30.4 32.6
400 2.0 1.12
easier if you twist it onto the shaft with a of the seal. 31.5 34.4
300 2.5 1.17
screwing action in the same direction as 32.7 36.0
3.0 1.22
200
the spring coiling. This screwing action Typical arrangements 34.0 37.6
3.5 1.26
100
35.3 39.1
will cause the spring to open. For brief 4.0 1.31
0
4.5 1.35 36.6 40.8
-200 -150 -100 -50 0 50 100 150 200 250 300
o
reversals of the direction of rotation we 38.0 42.4
Temperature ( C) 5.0 1.39
recommend seal type "S30". 39.3 44.0
5.5 1.44
thermal resistance, but it also displays 6.0 1.48 40.6 45.6
6.5 1.52 42.0 47.2
a high degree of rigidity, a low co- Drive side 48.8
(viewing direction) 7.0 1.57 43.3
efficient of thermal conductivity, an 45.7 50.4
Shrink disk Clamping set 7.5 1.61
unfavourable expansion characteristic Direction of shaft 46.1 52.1
8.0 1.65
(see graph) and a tendency to cold flow. rotation: clockwise 8.5 1.70 47.5 53.8
9.0 1.74 49.0 55.5
Rounded edges 50.4 57.2
Direction of spring coiling: clockwise 9.5 1.79
10.0 1.83 51.9 58.9
Mounting: Push spring onto shaft and turn
11.0 1.93 54.9 62.4
simultaneosly clockwise
11.5 1.98 56.4 64.2
12.0 2,02 58.0 66.0
Left-hand spring Right-hand spring Set screw Set screw 12.5 2.07 59.6 67.9
Joint on outer teflon jacket facing with cone point with cup point 13.0 2.12 61.2 69.8
against direction of assembly 13.5 2.17 62.9 71.7
Mechanical seal 14.0 2.22 64.5 73.6
direction of assembly anti- clock- 75.7
clockwise wise 14.5 2.27 66.2
shaft shaft 15.0 2.33 67.8 77.4
It is advisable, therefore, to avoid the Looking 15.5 2.38 69.5 79.3
use of O-rings made of solid PTFE. towards the 16.0 2.43 71.2 81.3
mechanical seals 72.9 83.3
16.5 2.49
The assembly position of double PTFE- 17.0 2.54 74.6 85.3
Allen set screw Drive key 87.4
en-capsulated elastomers is critical. with full dog point 17.5 2.59 76.3
Care must be taken to ensure that the Pressure vessel regulations 18.0 2.65 78.1 89.4
18.5 2.71 79.8 91.5
joint on the outer jacket faces against 81.6 93.6
Requirements imposed by various 19.0 2.76
the assembly direction, as otherwise 19.5 2.82 83.4 95.7
there is a risk of the jacket opening and international standards for Pressure 20.0 2.88 85.2 97.8
being pulled off. Vessel Code on Group III pressure 25.0 3.47 103.9 119.3
vessels (Section 8) 30.0 4.08 123.5 141.3
Bending of the jacket must be avoided • International Pressure Vessel Code 35.0 4.71 143.4 163.7
at all costs to prevent leaks. Slip TTV O- Conical spring Spring loaded 40.0 5.35 163.5 186.3
orders that pressure vessels be built 203.9 232.1
rings onto tubes for safe storage. drive pin 50.0 6.65
and operated in accordance with the 60.0 7.95 244.3 278.3
generally valid rules of engineering 70.0 9.26 284.7 324.4
(such as the German AD Code, ASME Shrink disk 80.0 10.58 325.1 370.8
etc). 90.0 11.89 365.6 417.1
The pressure necessary for the 100.0 13.20 406.0 463.5
• AD Bulletin W2 requires every
transmission of torque is generated 150.0 19.80 609.0 695.2
pressure-bearing part made of 200.0 26.40 812.0 926.9
through clamping force on lubricated
austenitic steel to be accompanied by a 250.0 33.00 1015.0 1158.7
conical surfaces. The shrink disk
material certificate EN 10204 3.1 B or 300.0 39.60 1218.0 1390.4
couplings can be released at any time
Screw locking 3.1C.
by slackening the tensioning screws. All
350.0 46.20 1421.0 1622.1
• The manufacturer must subject every 400.0 52.80 1624.0 1853.9
If no special provision is made for the parts involved are subjected to 500.0 66.00 2030.0 2317.4
pressure vessel to a pressure test.
locking screw thread, use set screw with elastic deformation only, so the original 600.0 79.20 2436.0 2781.0
• Every pressure vessels must be 700.0 92.40 2842.0 3244.5
a suitable adhesive (e.g. Loctite®) after clearance is restored once the screws
issued with a certificate confirming its 800.0 105.60 3248.0 3708.0
removing any grease. are released.
correct production and pressure testing Provided the conical surfaces are 900.0 118.80 3654.0 4171.5
in accordance with the Pressure Vessel 1000.0 132.00 4060.0 4635.0
undamaged, the shrink disks can be
Code. This certificate is included with retensioned any number of times Conventional units of measurement:
the delivery. (ensure correct lubrication). Shaft °E = degrees Engler
sleeves should not have a clearance R = Redwood Seconds I and II
SU= Saybolt Universal seconds
diameter under the shrink disk and
* according to Ubbelohde mm2/s  cSt
should make full contact with the shaft.

100
 Technical Information
In some cases, for mechanical seals to
Circulation function correctly the conditions in which
Barrier systems
For single seals it is generally advisable to install a they operate must be altered. This depends To guarantee the correct working of double
circulation pipe from the discharge nozzle of the pump on the seal type, the duty conditions mechanical seals, the barrier interspace (between the
to the seal chamber. A pipe size G1/4 is including environmental protection, and the product side and the atmosphere side of the
normally sufficient. There should be a close fitting neck type of equipment into which the seals are mechanical seal) must be completely filled with clean
bush between the pump casing and the seal chamber. fitted. barrier medium.
Before starting up double mechanical seals it is vital,
Flushing A simple change to a single seal's operating therefore, to ensure a sufficient rate of circulation of
Flushing systems are installed in accordance with DIN conditions in a dead-end arrangement can be the barrier fluid The barrier fluid pressure should lie
ISO 5199, Appendix E, Plan No. 08a or API 610, made, for instance, by adding a recirculation 10 % or at least 2....3 bar above the maximum
Appendix D, Plan 32. A clean and mostly cold pressure to be sealed. The flow rate must be
line from the pump discharge to the seal controlled to ensure that the temperature of the barrier
external medium is injected into the stuffing box in chamber (API Plan 1 ). medium at the outlet lies below approximately 60 °C
the area of the sliding faces via on orifice (throttle) and that it does not exceed boiling point under any
into the medium to be sealed. Flushing is used either As operational demands increase, so too circumstances. The maximum acceptable inlet/outlet
to lower the temperature or to prevent deposits must the capabilities of the supply units to temperature differential is 15 K. The barrier fluid outlet
forming in the area of the mechanical seal. Again it is support the mechanical seal. lies at the highest point of the stuffing box for
recommended that a close fitting neck bush is The following section contains the necessary automatic venting of any vapour. In view of the basic
employed. conditions of operation, a barrier system must perform
information for the correct selection of supply
the following functions:
Quench systems and auxiliary equipment to ensure
reliable operation of your mechanical seals.
Quench is the term commonly used in sealing  Build-up pressure in the barrier interspace
engineering for an arrangement that applies a  Compensation of leakage
pressureless external medium (fluid, vapour, gas) to a  Circulation of the barrier medium
mechanical seal's faces on the atmosphere side. A  Cooling of the barrier medium
quench is used on the one hand when a single  Cooling of the seal
mechanical seal does not function at all or only within
certain limits without auxiliary measures or when a Barrier medium Barrier fluid systems for liquid-lubricated mechanical
double mechanical seal with pressurized buffer medium seals break down into two basic categories:
is unnecessary. When an integral stationary seat stop is The barrier medium fulfills two functions -it dissipates
fitted, the quench pressure should not exceed 1 bar. A the heat generated by the seal and it prevents the  Open circuit

quench performs at least one of the duties described product from penetrating the sealing gap to any A circuit in which both the circulation and the
below. appreciable degree. Any liquid and any gas can be pressurization take place through a single barrier fluid
chosen as barrier medium, with due consideration to system.
Fluid quench
the corrosion resistance of the parts it comes into contact After each circuit the barrier fluid is relieved and
 Absorption or removal of leakage by the quench
with and to its compatibility with the process medium and collected in a pressureless tank.
medium Monitoring of the mechanical seal's leakage
rate by periodic measurement of the level of the surroundings. The barrier medium must not contain any
solids. It is particularly important that liquid barrier media  Closed circuit
quench medium in the circulation vessel or
do not tend to precipitate and that they have a high In this type of circuit all the components are kept
thermosiphon vessel Lubrication and cooling of the
boiling point, a high specific thermal capacity and good under the same pressure. Pressure is applied by
standby mechanical seal means of nitrogen or the process medium pressure or
 Exclusion of air: For media which react with thermal conductivity. Clean, demineralised water
via a refill system. Pressure loss in the circuit must be
atmospheric oxygen the quenching medium stops the satisfies these requirements to a high degree. taken into account when drawing up the design.
leakage making contact with the atmosphere Hydraulic oil is often used in buffer fluid units and
 Protection against dry running: For applications water in closed barrier fluid circuits. To prevent
subject to brief, periods of vacuum and operation of damage to the TS and sealing system, due allowance Nitrogen

pumps without pumping liquid (submersible pumps) must be made for the co-efficient of volumetric
the quenching medium prevents dry running of the expansion of the barrier fluids used.
mechanical seal
 Stabilization of the lubrication film: For operation
gas/g solvent

under vacuum and/or sealing pressures close to the

vapour pressure, the quenching medium stabilizes
Standard cm 2

the lubrication film

 Cooling or heating of the outboard side of the Mineral oil *

mechanical seal.
Steam quench Water
 Heating: For media with a high melting point the
vapour quench prevents the leakage from solidifying 80 Pressure (bar)
in that area of the mechanical seal critical for its * viscositiy at 38 °C : 34.9 mm2 /s
Methylene chloride
proper functioning 131 . 10-5
 Exclusion of air
Volumetric expansion [cm /l]

 Removal of leakage
60
3

Methanol
120 . 10-5 Air
Gas quench
 Icing protection: With operating temperatures <0 °C
(cryogenic mechanical seals), the injection of nitrogen 40
Ethanol
or dry air into the seal housing prevents the 110 . 10-5
gas/g solvent

mechanical seal parts on the atmosphere side from

icing up 20
Water
 Exclusion of air
18 . 10-5 Mineral oil *
Standard cm 2

 Removal of leakage

Sealing the quench medium

0 20 40 60
 Outboard mini-gland – the preferred choice for steam,
T Difference between the filling Water
not so much for liquids temperature (no-load temperature )
o
 Lip seals – the preferred choice for oils and water and the operating temperature ( C)
Pressure (bar)
 Mechanical seals – the preferred choice for all
Volumetric expansion of various * viscositiy at 38 °C : 34.9 mm2 /s
circulating quench fluids buffer media

101
 Technical Information

Circulation systems to API 682 / ISO 21049

Clean pumping media Buffer/barrier medium between seals Plan for atmospheric side
By purchaser to collection system
Plan 01

if specified
By vendor Normally Reservoir
Internal circulation from the Make up
open PI PS

Plan 52 Plan 51
SH

pump case to the seal. buffer fluid

LI
LSL
E x t e r n a l f l u i d r e s e r v o i r, Dead-end quench (usually

Reservoir
LBO
pressureless, thermosiphon or Q
methanol)
Plan 02 LBI
forced circulation as required. D

Dead end seal chamber with

no circulation. Stuffing box Plan 61
By purchaser to collection system
cooling and a neck bush are Tapped connections for the

if specified
necessary, unless otherwise By vendor Normally
open PI PSI
Plan 53A Q
customer's use.
Make up
specified. barrier fluid
6 LI
SH
Circulation with thermosiphon D
LSL
system, pressurized. Forced

Reservoir
Plan 03 LBO circulation by pumping ring or Plan 62
Circulation between the seal LBI circulation pump.
External fluid quench (steam,
chamber and the pump created Q gas, water, etc.)
Bladder charge
by the design of the seal connection

chamber. (eg. taper bore)

Bladder
accumulator
PI PSI
Plan 53B D
if specified
Make up
barrier fluid
Circulation with bladder
Plan 11 a c c u m u l a t o r a n d c o o l e r, Plan 65A
Circulation from the pump TI pressurized. Forced circulation by Atmospheric leakage
discharge, through an orifice LBO pumping ring or circulation pump. collection and detection for
to the seal. LBI condensing leakage with
failure detection by excess
Plan 12
Pressure
intensifier PI PSI
Plan 53C flow into system.
Circulation from the pump LSI
LI Make up
barrier
fluid
Circulation with pressure booster
if specified and cooler. Pressurized by
discharge, through a strainer reference pressure of seal
and an orifice to the seal. TI Plan 65B
LBO
chamber. Forced circulation by Atmospheric leakage
pumping ring or circulation pump.
LBI
collection and detection for
Plan 13 condensing leakage with
Circulation from the seal failure detection by
Plan 54
chamber, through an orifice cumulative leakage into
Circulation of clean fluid from an
and back to pump suction. LBO
external system. system.
LBI
Plan 14
Circulation from pump Plan 66A
discharge through orifice to Plan 55
External leakage detection
seal chamber and through External source to provide a clean
unpressurized buffer fluid to a dual arrangement with throttle
orifice back to pump suction. bushings.
(Combination of Plan 11+13). unpressurized seal.

Plan 71
if required Plan 21 Plan 66B
Ta p p e d c o n n e c t i o n s f o r
Circulation from the pump purchaser’s use. Typically this plan External leakage detection
discharge, through an orifice is used when the purchaser may arrangement with orifice plug.
and a cooler to the seal. use buffer gas in the future.
Plan 22
if required
Circulation from the pump Plan 72 Legend
discharge, through a strainer, Externally supplied buffer gas for
arrangement 2 seals. Buffer gas Cooler
an orifice and a cooler to the
may be used alone to dilute seal
seal. leakage or in conjunction with Plan Cyclone separator
Plan 23 75 or 76 to help sweep leakage into
if required Strainer
Circulation by means of a a closed collection system.
pumping ring from the seal, Pressure of buffer gas is lower than Flow control valve
through a cooler and back to process side pressure of inner
the seal. seal. Block valve
Non return valve
Plan 74
Contaminated and special pumping media Externally supplied barrier gas for Orifice
arrangement 3 seals. Barrier gas is D Drain
Plan 31 maintained at a pressure greater
than a seal chamber pressure. F Flush
Circulation from the pump
discharge through a cyclone FI Flow indicator
separator. Plan 75 Liquid buffer/barrier inlet
Cont ai nm ent s eal c ham ber LBI
By vendor
leakage collection system for LBO Liquid buffer/barrier outlet
Optional condensing or mixed phase
FI
Plan 32 leakage on arrangement 2 seals. LI Level indicator
PI
TI Injection of clean fluid into the This plan is used when pumped LSH Level switch MAX
seal chamber from an external fluid condenses at ambient
temperature. LSL Level switch MIN
source
PI Pressure indicator
Plan 76 Pressure switch
Containment seal chamber drain
PS
Plan 41 Pressure switch MlN
for non-condensing leakage on PSL
Circulation from the pump case arrangement 2 seals. This plan is
through a cyclone separator, and TI Temperature indicator
used if the pumped fluid does not
clean fluid through a cooler to the condense at ambient temperature. Q Quench
seal. 102
 Technical Information

Symbols Mechanical seals according to EN 12756 (code system)

A Area of sliding face For single mechanical seals there is a distinction drawn between standard (N) and short (K) types. For double
mechanical seals (back-to-back) EN specifies the short type only.
AH Area hydraulically loaded by medium
pressure
b Width of sliding face Single seal
c Position
Specific heat capacity Designation Description 1 2 3 4 5
D Outer diameter of sliding face
d Inner diameter of sliding face

Spring
Other metal parts (except seal cover and shaft sleeve)
Seal face

Secondary seals
Stationary seat
N = standard type with I1N
Da Outer diameter of bellows
K = short type with I1k
dH Hydraulic diameter C = type C
Di Inner diameter of bellows U = no shaft step
B = with shaft step
dm Mean diameter of sliding face C=0
dw Diameter of shaft Nominal diameters d1 and d10 of the mechanical seal
Shaft/shaft sleeve diameters are always three-digit numbers
f Coefficient of friction beneath the stationary seat for types U and B
Ff Spring force Direction of rotation of the Mechanical Seal
h Gap width Type N and K Type C
(is also the spring winding direction)
H Delivery head of pumping screw R = clockwise
Looking from the stationary seat toward the seal face Looking from the drive side with the shaft
k Balance ratio with the seal face rotating in clockwise direction rotating in clockwise direction
k1 Pressure gradient factor L = anti clockwise
n Looking from the stationary seat toward the seal face Looking from the drive side with the shaft
Speed with the seal face rotating in anticlockwise direction rotating in anticlockwise direction
p1 Medium pressure S = independent of direction of rotation
p2 Atmosphere pressure Spring type (state single spring or multiple springs in your order)

p3 Buffer fluid pressure

Pinned stationary seat
p p1-p2; p3-p1; p3-p2 0 = no torsion lock, without anti-rotation pin
pf 1 = with torsion lack, with anti-rotation pin
Spring pressure 2 = for type C
pG Sliding pressure
pr Material (see inside end cover)
Calculated load for the frictional
force of the secondary seal
PR Power consumption of sliding faces Double seal
Position
PV Turbulence loss through rotating Designation Description 1 2 3 4 5 6 7 8
parts
•
V Delivery rate
Seal face inboard
Stationary seat inboard
Secondaryseals inboard

Sliding face outboard

Stationary seat outboard
Secondaryseals outboard
Spring
Other metal parts
U = no shaft step
Q Mechanical seal leakage rate B = with shaft step on product side
C = type C
Ra Mean roughness index (calculated)
t,T Temperature of the medium to be U = no shaft step
B = with shaft step on atmosphere side
sealed C = type C
T Rise in temperature of the medium
to be sealed Nominal diameters d1 and d10 (always three-digit numbers)

t3 Temperature of the buffer medium Direction of rotation (see single seal)

vg Sliding velocity Anti-rotation pin for stationary seat on the atmosphere
and/or product side
 Dynamic viscosity 0 = without anti-rotation pin
1 = with anti-rotation pin for stationary seat on atmosphere side
 Load factor 2 = with anti-rotation pin for stationary seat on product side
3 = with anti-rotation pin for stationary seal on the atmosphere and
 Density product sides
4 = for type C
 Kinematic viscosity
Positive retention for stationary seat on the product side
0 = without
D = with
E = for type C
Material (see inside end cover)

103
 Technical Information
Seal and Material Code to API 682/ISO 21049 Seat locking*) to EN 12756 Balance ratio
Seal designations compliant 4th digit and other Supply The balance ratio is a non-dimensional factor
l6 l5
with ISO 21049 1st Issue and System Plans of the mechanical seal and is defined as
e
API 682 3rd Edition The cooling and/or flushing
0,3 Locking ring
diagrams used are listed here one k = hydraul. loaded area AH
The seal description was after the other without separating area of sliding face A
redefined in ISO 21048, Annex D. commas.
Contrary to the earlier 30
o

d9 H11
arrangement, no details such as Example 1:

d4
ds
the face and O-ring materials C1A1A11
Seal category 1 AH A
used are included in the Seal arrangement 1 (single seal) e
designation. Such details are now Seal type A (O-ring seal)
to be found only in the seal data Product circulation according to unbalanced k > 1
sheet. Plan 11

d9 H11
The following rule applies for Example 2:
seal codes with four or more C3A2B1152
Seal category 3 AH A
digits. e
Seal arrangement 2 (double seal
1st digit Seal Category pressureless)
Seal type B (rotating metal balanced k < 1
Here a C is used followed by the
corresponding category number bellows seal)
In practice k values are selected between
1, 2 or 3 to which the seal belongs. Product circulation according to
0.65 and 1.2. With a lower k value, the safety
Plan 11
Pressureless quench according against thermal overload will increase, but
2nd digit Arrangement
Here an A is used followed by the to Plan 52 the mechanical seal may also lift off more
d1 d2 d4 d9 l5 l6 e ds
number 1, 2 or 3 according to the easily.
seal arrangement applied. U B U B
10 14 22 26 26 30 1.5 4 4 - I) O-ring seal
3rd digit Seal Type 12 16 24 28 28 32 1.5 4 4 -
Here the letter A, B or C is used 14 18 26 34 30 38 1.5 4 4 -
according to the seal in question. 16 20 23 36 32 40 1.5 4 4 -

18 22 34 38 38 42 2.0 5 4 31.2
20 24 36 40 40 43 2.0 5 4 33.2
22 26 38 42 42 46 2.0 5 4 35.2
24 28 40 44 43 48 2.0 5 4 37.2
25 30 41 46 46 50 2.0 5 4 38.2
28 33 44 49 48 53 2.0 5 4 41.2
30 35 47 61 50 60 2.0 5 4 43.2
32 38 48 58 53 62 2.0 5 4 46.2 II) metal bellows seal
33 38 49 58 53 62 2.0 5 4 46.2
35 40 51 60 60 65 2.0 5 4 48.2 Unlike an O-ring seal, the hydraulic diameter
038 43 58 63 62 67 2.0 6 6 53.5 of a bellows seal is not a fixed geometric
040 45 60 65 66 70 2.0 6 6 55.5 value. It is conditional on the absolute level
043 48 63 68 67 72 2.0 6 6 58.5 of the pressure to be sealed and on the
045 50 65 70 70 75 2.0 6 6 60.5 direction of pressurization (internal or
048 53 68 73 72 77 2.0 6 6 63.5 external pressure).
050 55 70 75 75 86 2.5 6 6 67.5
053 58 73 83 77 86 2.5 6 6 70.6
055 60 75 85 86 91 2.5 6 6 72.6
058 63 83 88 88 93 2.5 6 6 75.6
060 65 85 90 91 96 2.5 6 6 77.6
063 68 88 93 93 98 2.5 6 6 80.6
065 70 90 95 97 103 2.5 6 6 82.6
068 - 93 - 98 - - - 6 88.6
070 75 95 104 103 018 2.5 7 6 90.2
075 80 104 109 108 150 2.5 7 6 95.2
080 85 109 114 120 125 3.0 7 6 103.0
085 90 114 119 125 130 3.0 7 6 108.0
090 95 119 124 130 136 3.0 7 6 113.0
095 100 124 129 135 140 3.0 7 6 117.5
100 105 129 134 140 145 3.0 7 6 122.5
*)
not applicable for seats made of carbon.

104
 Technical Information
Contact
friction Boundary friction Liquid friction
1,0
Roughness 10 m 1 m 5 m 0,1 m Degree of
0,5 precision turned ground tapped polished roughness in
0,3
relation to the
0,2 percentage bearing
Coefficient of friction f

0,1

Percentage
0,05 bearing area 4 % 12 % 40 % 95 %
0,03
0,02

0,01
10-9 2 3 5 10-8 2 3 5 10-7 2 3 5 10-6 2 3 5 10-5 2 3 5 10-4
Hydrodynamic coeff. (G) h.w
G=  . p

Load factor  Coefficient of friction f Surface roughness Turbulence losses Pv

The balance ratio is just a non- The coefficient of friction f is conditional Microfinished sliding faces made of The turbulence-related consumption of
dimensional factor used to assess a on the materials that are in contact, the various materials display the following power is not significant until the
average, arithmetic mean roughness
mechanical seal. A second one is the medium being sealed, the sliding values (Ra): circumferential speed reaches 30 m/s. It
load factor . velocity and the design-related Tungsten carbide. : 0,01 m must be given due consideration
 = k + pf + pr conditions of contact between the nickel-bonded particularly with special seals.
p
sliding faces. Silicon carbide (SiC) : 0,04 m
The balance ratio and the load factor are For general considerations and Special cast Cr-steel : 0,15 m Power consumption
practically identical when the pressure calculations, a coefficient of friction of Carbon graphite : 0,10 m The total power consumption of a
differentials to be sealed are large. The between 0.05 and 0.08 can be applied Aluminum oxide : 0,15 m mechanical seal is calculated from
friction at the dynamic secondary seals as a good approximation. As can be C-SiC-Si/C-SiC : 0,15 m • The power consumed by the sliding
pr is usually disregarded in the seen in the graph, a lower value is The lower the roughness value, the faces.
calculation. obtained under improved conditions of • The power consumption due to
higher the percentage bearing area and
Sliding pressure pg lubrication, e.g. due to partial build-up of hence the higher load capacity of a turbulence created by the rotating parts.
hydrodynamic pressure in the sealing mechanical seal.
The term "sliding pressure" is 220
Example:
gap. On the other hand, when a
Mean sliding Face diameter dm (mm)

200
understood to be the surface pressure dm = 170 mm
mechanical seal is run under purely 180
n = 4500 min-1
on the two sealing faces which remains
hydrodynamic conditions of operation,
1000
500

1500

160
vg = 40 m/s
2000
30 0
250

after subtracting all those forces that act

350 00
4 0

140
the coefficient of friction will rise as the
4 000
5 500
60 000

on the seal face and which are balanced 120

80 000 0

speed increases - similar to )

0

-1

(min
by hydraulic pressures. The sliding 100 dn
00

pee
7

00 ft s
hydrodynamic bearings. 80 90 0000
1 000
Sha
pressure is conditional on the pressure 12 00
60 140000
168000
differential to be sealed, the balance 40
1 000
20
ratio, the pressure conditions inside the Gap width h 20
0 10 20 30 40 50 60 70 80 90 100
sealing gap i.e. gap between the seal Sliding velocity vg
Seals with contacting faces
faces (pressure gradient factor) and the In contact seals with a theoretically
spring pressure. The pressure gradient parallel sealing gap, the distance
Sliding velocity vg Heat transfer
factor k1 can assume values between 0 between the two sealing faces is The sliding velocity is usually quoted in The total power consumption of a
and 1, depending on the geometry of the conditional on the roughness of the relation to the mean sliding face mechanical seal has to be dissipated
two sealing faces. For sealing gap surfaces. diameter. into the medium or the buffer fluid by
geometries which converge in leakage Numerous measurements taken in the means of appropriate measures in order
direction - V-gap for externally laboratory and in practice with due Cooling water requirements to stop the seal from overheating. The
necessary fluid flow rate for removal of
pressurized seals - the value of k1 is > allowance for external factors indicate When estimating the amount of cooling the power losses is calculated by
that a mean gap width of less than 1 mm water required by heat exchangers it •
0.5, while for sealing gap geometries V = PR + PV
can be used as a basis for calculating can be assumed that the temperature of
which diverge in leakage direction - A- T • c • 
the normal degree of leakage. the cooling water will increase by 5 K
gap for externally pressurized seals - between the inlet and the outlet. This Under certain conditions of installation
the value of k1 < 0.5. For simplified Seals with non-contacting faces means that 1 l/min of cooling water or operation heat may pass from the
Hydrostatically or hydrodynamically dissipates 350 W. product to the sealing compartment and
calculations the value of k1 is generally
balanced, non-contacting mechanical will need to be taken into account when
taken to be 0.5. Under unfavourable calculating the circulation rate.
conditions the sliding pressure can seals adjust automatically to a defined
gap width during operation. The width of Example calculation:
become negative, causing the sealing
the gap depends mainly on the shape of PR = 420 W ( 1 W = 1 J /s)
faces to open resulting in excessive T = 10 K
leakage. the gap in radial as well as
Fluid: Water;
circumferential direction, on the c = 4200 J (kg • K)
operating conditions and on the  = 1 kg / dm3
pg=  p. (k - k1 ) + p f medium. • 3
V = 420 W • kg • K • dm
10 K - 420 Ws - 1 kg
= 0.01 l/s = 0.6 l/min 

105
 Technical Information
Prior to installation Axial run-out Surface finish Extrusion characteristics
of elastomeric O-rings
To fit a seal you will need its installation Mounting face Finished surfaces according to
and operating instructions with the Axial run-out depends on the speed. EN12756 The extrusion resistance of elastomeric
correct drawing. Before starting, check Permissible values are indicated by the O-rings can be greatly enhanced by the
the dimensions, the maximum graph. use of support rings.
acceptable deviations and the Ra  b
Ra w Ra w Ra  b 600
geometrical tolerances of the machine.
Edges and shoulders 400

All edges and shoulders onto or into 300

Pressure differential (bar)

200
which the mechanical seal is pushed
Ra  b
during installation must be chamfered, 100
Extrusion
Ra  b
deburred and rounded off to less than Ra  w 80
60
30° x 2 mm.
1,5
40
Dimensional deviations 1,0
Permissible tolerance (mm)

Acceptable deviations for dimensions for secondary seal 30

0.5
0.4 Mean roughness material Ra
No Extrusion
0.3 20
having no tolerance specification: index Shore A hardness7 0 8 0 90
0.2
b w
ISO 2768 0.1
Elastomers 2.5 m 0.8 m 10
• Part 1, fine/medium for linear and 0.05
0.04 Non-elastomers or 8
0 0,1 0,2 0,3 0,4 0,5 0,6 0,7 0,8 1, 0
angular dimensions 0.03
0.02 optional use of 1.6 m 0.2 m Total radial clearance in mm
• Part 2, tolerance class K for general 0.01 elastomers and
0 500 1000 1500 2000 2500 3000 3500
geometrical tolerances Speed n (rpm)
non-elastomers

Concentricity tolerance Mechanical Seal Installation

Shaft in accordance with ISO 5199 Absolute cleanliness and care are Screw locking Venting
In the area of the mechanical seal the essential when fitting mechanical seals. If no special provision is made for To prevent damage to the sliding faces
shaft concentricity tolerance must not locking screw threads, use set screws from dry running, the buffer space must
Dirt and damage to sliding faces and
exceed 50 m for diameters < 50 mm,
O-rings jeopardize a seal's function. Any with a suitable adhesive (e.g. Loctite®) be carefully vented after you have
50 m- 80 m for diameters between 50
and 100 mm, and 110 m for diameters protective covering on the sliding faces after removing any grease. installed the seal. This is particularly
> 100 mm. must be removed without trace. Never important for those types of
Seal chamber bore put lubricant on the sliding faces - mount buffer/barrier fluid systems that do not
For sliding velocities of vg < 25 m/s the only in a completely dry, dust free and vent themselves or are partially self
concentricity tolerance of the seal venting (double seal with buffer/barrier
clean state. The accompanying
chamber in relation to the shaft should
installation instructions and the notes on fluid systems).
not exceed 0.2 mm, and when pumping
screws are used it should not exceed the assembly drawings must be
0.1 mm due to the effect of the pumping observed exactly.
characteristic. If these values are
exceeded please contact Sealmatic. Fitting advice
To reduce the friction on O-rings when
mounting seals on a shaft or when
inserting seal cartridges in their
housing, apply a thin coating of silicon
grease or oil to the shaft or housing
(N.B.: this does not apply to elastomer
bellows seals). Never allow EP rubber
O-rings to come into contact with
mineral oil or grease. When inserting
stationary seats, be careful to apply
even pressure and use only water or
alcohol to reduce O-ring friction.

106
 Stationary Seats General Table

Seats Types of Seals

U740(F)-D

B740(F)-D

UFL800N
U370GN

B170GN
U700(F)
U740(F)

B700(F)
B740(F)

BJ970G
Seal

UG100
UG120
UG130
UG943

U370G

U320N

B120N

TB850
BJ920
Type Version Description/ materials

U300
U320
U370
Type
solid
Special Cast Chrome Steel,
G4 U320 Ceramic,
Silicon Carbide/Tungsten Carbide
solid
Special Cast Chrome Steel,
G6 U320N4 Ceramic,
Silicon Carbide/Tungsten Carbide
solid
Special Cast Chrome Steel,
G7 U320S8 Ceramic,
Silicon Carbide/Tungsten Carbide
solid
Special Cast Chrome Steel,
U320N Ceramic,
Silicon Carbide/Tungsten Carbide

U700N Carbon Resin/Antimony Impregnated

G9
to
DIN B700N Carbon Resin/Antimony Impregnated
24960
Shrunk in
U377GN Tungsten Carbide/ Silicon Carbide

Shrunk in
U177GN Tungsten Carbide/ Silicon Carbide

Shrunk in
G12 U377G Tungsten Carbide/ Silicon Carbide

solid
G13 U300 Carbon Resin/Antimony Impregnated

Shrunk in
B721G15 Tungsten Carbide/ Silicon Carbide
G15
B740G15 (cooled)
solid
Special Cast Chrome Steel,
G16 BJ920N Ceramic,
Silicon Carbide/Tungsten Carbide

Shrunk in
G18 U377GS8 Tungsten Carbide/ Silicon Carbide

solid
G30 U300N4 Carbon Resin/Antimony Impregnated

double-elastic mounted,
solid
G35 TB850 Ceramic, Tungsten Carbide/
Silicon Carbide

G42 TB850 Ceramic, Tungsten Carbide/

Silicon Carbide

solid
G50 UG943 Special Cast Chrome Steel, Ceramic,
Silicon Carbide/Tungsten Carbide
solid
G55 UG943 Special Cast Chrome Steel, Ceramic,
Silicon Carbide/Tungsten Carbide
solid
G60 UG100 Special Cast Chrome Steel, Ceramic,
Silicon Carbide/Tungsten Carbide
solid
G115 B750G115 Silicon Carbide/Tungsten Carbide
(Cooled)

Default
Optional

107
 Table of Materials

Face Materials (Item 1/2) Metal Oxides (Ceramics) Non-Elastomers

G Pure graphite
V Al-Oxide > 99%
Synthetic Carbons V2 Al-Oxide > 96% T PTFE (Polytetrafluoroethylene)
X Steatite (Magnesia silicate) T2 PTFE glass fiber reinforced
T3 PTFE carbon reinforced
A Carbon graphite antimony impregnated
T12 PTFE carbon-graphite reinforced
B Carbon graphite resin impregnated,
approved for foodstuffs Plastics
B3 Carbon graphite resin impregnated Spring and Construction Mat. (Item 4/5)
B4 Electrographite resin impregnated
Y1 PTFE, glassfiber reinforced
B5 Carbon, resin bonded
Y2 PTFE, Carbon reinforced
C Electrographite antimony impregnated Spring Materials

G 1.4571 CrNiMo Steel

Metals
M 2.4610 Hastelloy® C-4
Secondary Seal Components (Item 3) Nickel-base alloy
E Cr-Steel
G CrNiMo-Steel Elastomers, not wrapped Construction Materials
S Special cast CrMo-Steel
D St C steel
B Butyl rubber E 1.4122 Cr steel
Carbides E Ethylene propylene rubber F 1.4301 CrNi steel
K Perfluorocarbon rubber F 1.4308 CrNi cast steel
U = Tungsten carbides N Chloroprene rubber F1 1.4313 Special cast CrNi steel
U1 Tungsten carbide, Co-binder P Nitrile-butadiene-rubber G 1.4401 CrNiMo steel
U2 Tungsten carbide, Ni-binder S Silicone rubber G 1.4404 CrNiMo steel
U22 Tungsten carbide, Ni-binder V Fluorocarbon rubber G 1.4571 CrNiMo steel
(shrunk-in) X HNBR G 1.4581 CrNiMo cast steel
U3 Tungsten carbide, NiCrMo-binder G1 1.4462 CrNiMo steel - Duplex
U37 Tungsten carbide, NiCrMo-binder G1 1.4460 CrNiMo steel-Duplex
(shrunk-in) Elastomers, wrapped G1 1.4410 CrNiMo steel surperduplex
U7 Tungsten carbide, binder-free
G4 1.4501 CrNiMoCu steel - Superduplex
FKM, double PTFE wrapped G3 1.4539 NiCrMo steel
Q = Silicon carbides M1
EPDM, double PTFE wrapped G4 1.4501 CrNiMoCu steel - Superduplex
M2
Q1 SiC, silicon carbide, sintered
M3 VMQ, double PTFE wrapped M = Nickel-base alloy
pressureless
M4 CR, double PTFE wrapped
Q12 SiC, silicon carbide, sintered M 2.4610 Hastelloy® C-4
M5 FKM, FEP wrapped
pressureless (shrunk-in) M1 2.4617 Hastelloy® B-2
Q2 SiC-Si, reaction bonded M7 FKM, double PTFE wrapped/
M3 2.4660 Carpenter® 20 Cb3
PTFE solid
Q22 SiC-Si, reaction bonded(shrunk-in) M4 2.4375 Monel® alloy K500
Q3 SiC-C-Si, carbon silicon impr. M5 2.4819 Hastelloy® C-276
Q32 SiC-C-Si, carbon silicon impr. M6 2.4668 Inconel® 718
Q6 SiC-C, SiC, sintered pressureless Differing Materials T = Other materials
with carbon
Q4 C-SiC, carbon surface silicated T1 1.4505 CrNiMoCuNb steel
Q19 SiC,DLC- coated U1 Perfluorocarbon rubber/PTFE T2 3.7035 Pure Titanium
Q15 SiC,Diamond face T3 2.4856 Inconel® 625
T4 1.3917 Carpenter® 42
Standards followed:
T5 1.4876 Inconel® 800
EN 12756
T6 - AM350
ISO 1629
Material code designation example

5 4 5 3 1 2 3

Item 1 2 3 4 5
Material code Seal face Stat. face Secondary Seals Spring Other parts
acc.to EN 12756 Q1 B V G G
Example : Sealmatic U700N/d1 Q1 B V G G