15epme011 Strength of Materials

ANSWER KEY
18ESME401 STRENGTH OF MATERIALS
8 Mark Questions
Answer Key
1. A mild steel rod 2m long &3cm diameter is subjected to an axial pull

of 10kN. E for Youngs modulus for steel is 2 x 105 N/mm2. Find the
stress, strain.
Lenth (l) = 2 m = (2 1000) mm

Diameter (d) = 3cm,
Area a=π(3 x 1000)/4
Arial pull = 10KN = 10 103 N =706.5

E = 2 105 N/mm2
Stress =10 x 10 N/mm2 / 706.55mm =14.15N/mm
E=Stress/Strain
Strain = 14.15/2 x 10
=0.0000707
2.A steel bar 900mm long its 2ends are 40mm &30mm in diameters &the
length of each rod is 200mm. The middle portion of the bar is 15mm in
diameters &500mm in long if the bar is subjected an axial tensile load of
15KN. Determine the stress in each section &total extension. Take E=200
103N/mm2.
To find stress at each section:

Stress at 1 section AB =Pull /Area
αAB=15 x 103 / π/4 (40)2
αAB=11.94 N/mm2
3
Stress at section BC = 15 x 10
2
αBC=84.92N/mm
Stress at section CD = 15.103
αCD=21.23 N/mm2
To find total Extension (or) Elongation
3. The following are the results of a tensile on test on a molested rod is 16

mm gaugh length is 50 mm, load at proportionality limit is 48.5 kN.
Extension at the proportionally limit is 0.05mm. Load at yield point is 50.3
KN ultimate load is 90KN. Final length between gauge points is 64mm, dia
of the neck at fracture is 13.7 mm. Determine the young’s modules at
elastic limit, Yield stress, Ultimate Stress, % of elangation & % of reduction
in area.
Dia of rod d = 16mm
Load at yield point = 50.3KN

= 14/50 x 100
4. A Cylindrical pipe of diameter 1.5mm & thickness 1.5cm is subjected to
2
an internal fluid pressure of 1.2 N/mm . Find the longitudinal stress & hoop
stress developed in the pipe.
5. A Cyliner of internal dia 0.5m contains air at apressure of 7 N/mm2.If the

maximum permissible stress induced in material is 80 N/mm2. Find the
thickness of the cylinder .
UNIT II BEAMS - LOADS AND STRESSES
Answer Key
1. A Beam of Total length 8m is freely supported at a left end & at a

point 6m from left end. It carries 2 points floats of 15KN & 18KN. In
which one is at the free end and another is 3m from the left support.
Draw the shear force and bending moment diagram. Locate the point of
contraflexture.
To fine the support reactions:
Taking moment about A,

(Rc 6) – (18 3) – (10 8) = 0
6 Rc = 54+120
Rc = 174/6
Rc = 29 KN
RA + Rc = 18+15
RA + 29 = 33
RA = 4 KN
To fine Shear force:
Shear force at D = 15 KN
Shear force at C = 29 KN +15 = -14 KN
Shear force at B = -14+18 = 4 KN
Shear force at A = 4 KN
To find bending moment

Bending Moment at D = 0
Bending Moment at C = -(15 2) = - 30 KNm
Bending Moment at B = -(15 5)+(29 3)
Bending Moment at A = -(15 8) +(29 6)-(18 3)
= -120-54+174 =0
2. The cast iron bracket subjected to bending has a cross section of I-

shaped with unequal flanges as shown. If the compressive force on the top
of the flanges is not to exceed 17mega pa. What is the bending moment of
the section can take if the section is subjected to a shear force of 90KN.
Area of section (1) = lb

= 250x 50
= 12750mm2

= 50 250 = 12500mm2
= 150 50 = 7500mm2
To find centroid distance:
y1 = 50+250+50/2 =325mm
= 501995840.7
3.A beam of length 10 is simply supported at its end carries two
concentrated loads of 5KN each at a distance of 3m and 7m from the
left support and also a uniformly distributed load of 1KN/m between the
point loads. Draw the shear force and bending moment diagram.
4.A cantilever 15 m long is loaded with uniformly distributed load of
2KN/m runs over a length of 1.23m from the free end. It also carries a
point load of 3KN at a distance of 0.25m from the free end. Draw the
shear force and bending moment diagrams of the cantilever.
5. Draw the shear force and bending moment diagram of the beam
loaded as shown in figure. Also determine the point of contraflexure if
any.
UNIT III Torsion
Answer Key
1.A metal bar of 10mm dia when subjected to a pull of 23.55KN gave
and elongation of 0.3mm on a gauge length of 200mm. In a torsion
test maximum shear stress of 40.71N/mm2 was measured on a bar
of 50mm dia. The angle of twist measured over a length of 300mm
being 0o21’. Determine poisson’s ratio.
=23.55 x 103 / 78.5 = 78.5mm2
P = 2πft/1000
2. A hollow shaft dia ratio 3/5 is required to transmit 450Kw at

1200pm, the shearing stress in the shaft must not exceed 60N/mm2
and the twist in a length of 2.5m is not to exceed 10. Calculate the
minimum external of the shaft. Take, C=8.0KN/mm2.
3
= 3.0427 x 10 N/mm
3. What must be the length of a 5mm dia aluminium wine so that it

can be twisted through 1 complete revolution without exceeding a
shear of 42N/mm2. Take, G=27 GPO.
I= π/32 d4 =π/32(5)4 =6111.328mm2
4. A solid steel shaft has to transmit 75Kw power at 200 pm. Taking
allowable shear stress 70Mpo. Find suitable dia of shaft with the maximum
torque transmitted on each revolutions exceeds by mean by 30% ->1.3
times mean.
d = 6.969= 69.69mm
5.A closely coiled helical spring is made of 10 mm diameter steel
rods. The coil consists of 10 complete turns and the mean diameter
is 120 mm. The spring carries an axial pull of 200 N. Assuming G = 80
kN/mm2, determine (i) Deflection in the spring (ii) Strain energy
stored (iii)Maximum shear stress
UNIT IV BEAM DEFLECTION
8 marks
1.Determine the deflection of a given beam at the point loads. Take I =

64x10-4 mm4 & its Young’s modulus (E) = 210x106 N/mm2.
To find Support reactions:
Equation (3) is a deflection equation
Boundary conditions:
EI (0) = 15(0) + c1(0) + c2

2. A steel cantilever beam of 6m long carries 2 point loads 15KN at the free
end and 25KN at the distance of 2.5m from the free end. To determine the
slope at free end & also deflection at free end I = 1.3x108mm4. E = 2x105
N/mm2
2
a2 = 3.5x37.5 = 131.25m
Area of section (3) =1/2(bh)

3.A beam is simply supported as its end over a span of 10m and carries
two concentrated loads of 100KN and 60 KN at a distance of 2m and 5m
respectively from the left support.Calculate the slope at the left
support.Assume EI=36 x 104 KN/m2
4.A cantilever projecting 3m from a wall carries a UDL of 12KN/m for a
length of 2m from the fixed end and a point load of 1.5KN at the free
5 2
end.Find the deflection at the free end. Take E = 2 x 10 N/mm and I=1 x
8 4
10 mm
5.A simply supported beam is loaded as shown in figure is 200mm wide
and 400mm deep. Find the slopes at the supports. Take E = 2 x 104 N/mm2 .
UNIT V ANALYSIS OF STRESSES IN TWO DIMENSIONS
8 marks
1. The mild steel block has cross-section of 50x50mm carries an axial load
of 35KN which is compressive in nature. Find the normal, tangential
stresses across the plane through the point of 30o to the axis of the block.
Also find the maximum shear stress in the block.
2. A member subjected to a pull of two pieces wooden frame of cross
section (35x15)mm connected by bolts joints. Calculate the maximum
permissible value of P which can withstand if the permissible normal,
tangential stresses is 13N/mm2 and 8N/mm2. Angle of cross section is 40o
.
P = 13 x (35x15)/0.5868
3. A 5mm thick aluminium plate has a width of 300mm and a length of

600mm subjected to pull of 15000N,9000N respectively in axial transverse
directions. Determine the normal, tangential and resultant stresses on a
plate 50°.
Transverse stress (α2)=9000/(5 x 600) = 3N/mm2
4. The principle stresses at a point in the section of a heat exchanger shell
are 18MPa (Tensile) and 10MPa (Compressive). Acting mutually
perpendicular to each other. Determine the normal, shear, resultant stress
on a plane whase normal is inclilned at 60° to 10MPa stress. Find also the
maximum shear stress.
= -3 N/mm2
5. A steel bar is under a tensile stress of 65N/mm2 at the same time it is
accompanied by a shear stress of 22.5N/mm2. Find the normal, shear
stress and resultant stress across a plane at an angle of 45° with the axis
of major tensile stress and also find the maximum shear stress.
= 32.5N/mm2

15epme011 Strength of Materials

Uploaded by

Copyright:

Available Formats

15epme011 Strength of Materials

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

15epme011 Strength of Materials

Uploaded by

Copyright:

Available Formats

ANSWER KEY

18ESME401 STRENGTH OF MATERIALS

1. A mild steel rod 2m long &3cm diameter is subjected to an axial pull

Lenth (l) = 2 m = (2 1000) mm

Area a=π(3 x 1000)/4

Arial pull = 10KN = 10 103 N =706.5

Stress =10 x 10 N/mm2 / 706.55mm =14.15N/mm

To find stress at each section:

αAB=15 x 103 / π/4 (40)2

Stress at section CD = 15.103

To find total Extension (or) Elongation

3. The following are the results of a tensile on test on a molested rod is 16

Dia of rod d = 16mm

Load at yield point = 50.3KN

5. A Cyliner of internal dia 0.5m contains air at apressure of 7 N/mm2.If the

1. A Beam of Total length 8m is freely supported at a left end & at a

To fine the support reactions:

Taking moment about A,

To find bending moment

2. The cast iron bracket subjected to bending has a cross section of I-

Area of section (1) = lb

Area of section (2) = lb

2. A hollow shaft dia ratio 3/5 is required to transmit 450Kw at

3. What must be the length of a 5mm dia aluminium wine so that it

UNIT IV BEAM DEFLECTION

1.Determine the deflection of a given beam at the point loads. Take I =

EI (0) = 15(0) + c1(0) + c2

Area of section (3) =1/2(bh)

3. A 5mm thick aluminium plate has a width of 300mm and a length of

You might also like