TIBAG HIGH SCHOOL

(Formerly Maliwalo National High Schol – Annex)

Tibag, Tarlac City
3rd Quarter Summative Test
in T.L.E. (Grade 7 – Carpentry)

Name:__________________________________________________ Date:___________________
Grade & Section:________________________________________ Score:__________________

I.Direction: Read and analyse the following questions below. Choose the letter of the correct answer.

1.It is a measuring tool used to transfer measurements from the rule to the work.
A. Try square B. Caliper C. Meter Stick D. Pull-Push Rule
2.It is a measuring tool used for squaring, measuring and testing tool used to check adjacent surfaces for square
ness.
A. Try square B. Caliper C. Meter Stick D. Pull-Push Rule
3.It is a marking lining tool used to scribe arcs and circle in a metal wood.
A.Pencil B.Chalk line C. Pencil D. Compass
4.It is a marking lining tool with two legs used to lay-out an arc circle or step off division on a line.
A. Pencil B. Marking gauge C. Compass D. Divider
5.It is a tool used to test the vertical and horizontal surfaces.
A.Plumb bob B.Steel Square C.Try square D. Spirit level
II. Compute the number of board feet of lumber with the following dimensions
6.) 2” x 6” x12” A. 15 B. 10 C. 12 D. 13
7.) 3” x 4” x10” A. 10 B. 12 C. 12. D. 15
8.) 2” x 2” x 16” A. 6 B. 8 C. 7 D. 5
9.) 2”x 12” x 8” A. 15 B. 16 C. 17 D. 18
10.) 4” x 4 “ x 18” A. 24 B. 23 C. 24 D. 25
11.An arrangement in a drawing of the three principal views of an object.
A. Projections B.Orthographic C. Sketch D. Design
12.It is a freehand drawing of an object
A. Sketch B. Projection C. Orthographic D. Design
13.It is a definite measure shown on a drawing in detail.
A.Projection B.Specification C. Dimension D.Sketch
14.t is a heavy line draws freehand for some purpose as long break
A. Center line B. Dimension line C. Long break line D. Visible line
15.A light line used as axis of symmetry.
A. Center line B. Dimension Line C.Long Break line D. Visible line
16.A light thin lines used to show the sizes of the object.
A. Dimension line B. Center line C. Invisible line D. Visible line
17.A medium line used to show edges and contours not visible to the eye.
A. Dimension line B. Invisible line C. Visible line D. Borderline
18.It is a heavy, solid line used to frame in the drawing.
A. Dimension line B. Center line C. Visible line D. Borderline
19.Which shall be used as temporary means of warning an existing hazard such as defected tools, equipment ,etc?
A. danger signs B. accidental prevention tags C. traffic signs D. directional signs
20.Which shall be used when an immediate hazard exists?
A. signs, signal & barricades B. danger signs C. exit signs D. safety instructions signs
21.It ensures the safety of the construction workers.
A. signs ,signal & barricades B. danger signs C. exit signs D. safety instructions signs
22.Which is practiced when your colleagues decide with you which things to put where taking into account the flow
of your work?
A. sort B. systematize C. sweep D. sanitize
23.It is the condition where high standard of good housekeeping is maintained so that there is no dust and rust
anywhere.
A. sort B. systematize C. sweep D. sanitize
24.Accidents can be prevented ___________________.
A. through the proper care and maintenance of tools and equipment
B. right attitude towards work
C. if you have a good knowledge about safety practices
D. None of the above
25.Who should first know about the accident that happened in your shop?
A. principal B. nurse C. teacher D. doctor
26.Identifying hazards makes you ________________.
A. safe from working B. comfortable while working C. work efficient D. all of the above
27.OSH means ________________________
A. Occupational Service Healthy B. Occupational Safe and Healthy
C. Occupational Safety and Health C. Occupational Safety and Health
28. Your employer must conduct a hazard assessment in order to_______________.
A. avoid accident B. promote accident C. eliminate workers D. None of the above
29.Conducting hazard assessment to a workplace should be done_______.
A. during work hours B. after working hours C. before working hours D. all of the above
30.Observing good housekeeping _____________.
A. prevents fire C. both a and b
B. makes for easy location of tool and materials needed D. none of the above
31.In dealing with accidents, the first thing to do is to _____________.
A. stay calm and study the situation C. call the attention of your teacher
B. apply first aid D. all of the above
32.Accidents can be prevented _________________.
A. thru proper cares and maintenance of tools and equipment
B. right attitude towards works
C. if you have enough knowledge about safety practices
D. all of the above
33.When an injury occurs, how soon should it be treated?
A. After class hours B. Immediately C. Both a and b D. Later
34. Which is a major factor for the prevention of shop accidents?
A. Signs, symbols, barricades B. The 5 Ss Principle C. Attitude D. all of the above
35. Which shall be used as temporary means of warning an existing hazard such as defected tools and equipment?
A. Danger Signs B. Accidental Prevention tags C. Traffic Signs D. Directional Signs
36.Which shall be used when an immediate hazard exists?
A. Signs, Signal, Barricades B. Danger Signs C. Exit Signs D. Safety Precautions Signs
37. It ensures the safety of the construction workers.
A. Signs, Signal, Barricades B. Danger Signs C. Exit signs D. Safety Instructions Signs
38. Its advantage is to promote camaraderie among workers in the company
A. Shitsuke B. Seiton C. The 5Cs D. All of the above
39. Which is practiced when your colleagues decide with you which things to put where taking into account the flow
of your work?
A.Sort B. Systematize C. Sweep D. Sanitize
40.It is the condition where high standard of good housekeeping is maintained so that there is no dust and rust
anywhere.
A. Sort B. Systematize C. Sweep D. Sanitize
41.It refers to the cleaning of workshop.
a. Seiton B. Seiri C. Seiso D. Seiketsu
42.Which is a control measure on accident preventation?
A. Workplace communication and consultation
B. Safety and health committee meetings
C. Regular equipment and work safety checks
D. All of the above
43.Which is a step on risk management?
A. Identification of Safety Procedures B. Hazard Identification
C. Training the Workers D. All of the above
44.Which is a risk?
A. Out of control cutting machine B. Vibration
C. power cords D. beard, loose hair, loose clothing
45. Which is a common hazard?
A. obstruction B. damaged saw blades C. hazardous dusts D. all of the above
46.Which is NOT PPE?
A. helmets B. goggles C. gloves D. shorts
47.What government agency is responsible primarily for setting and enforcing mandatory occupational health and
safety standards?
A. DPWH B. Civil Service Commission C. DOLE D. DBM
48. Which primarily uses least resources in the workplace?
A. Occupational Health and Safety B. Risk management
C. Work Procedure D. Work Simplification
49. Who are covered by the Occupational Health and Safety Regulations?
A. Employers B. Workers C. Self-Employed D. all of the above
50.Which is the emphasis of continuous training of the workers as hazards/risk management measure?
A. Workplace safety and health B. emergency and first aid procedures
C. Hazards and risks associated with work activities D. All of the above

Prepared by:

MARK DARRYL D. TACUBANZA JONATHAN PAUL L. BRIONES ROMEO D. MACAHILO CHRISTINE JOY P. DAVID
Teacher – I Master Teacher – I Teacher – III Teacher – I

Checked by: Noted by:

EVANGELINE V. ESPIRITU JUVELYN L. ESTEBAN EdD.

Head Teacher – I Principal IV
ANSWER 1.B 26.D KEY
2.A 27.C
3.D 28.A
4.C 29.D
5.A 30.C
6.C 31.D
7.A 32.D
8.D 33.B
9.B 34.D
10.C/A 35.A
11.B 36.C
12.A 37.A
13.C 38.D
14.C 39.B
15.A 40.D
16.A 41.C
17.B 42.D
18.D 43.D
19.A 44.D
20.A 45.D
21.D 46.D
22.A 47.C
23.D 48.D
24.C 49.B
25.C 50.A