Scribd
Upload
39 views15 pages

Base Plate INDIA CODE

The document provides calculations for the design of a base plate for a column. It includes calculating forces on the base plate from structural analysis, checking geometric requirements for bolt spacing and edge distances, and verifying the base plate and bolts have sufficient capacity for bearing pressure, shear, tension and a combined shear and tension check.

Uploaded by

mathewsujith31
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
39 views15 pages

Base Plate INDIA CODE

The document provides calculations for the design of a base plate for a column. It includes calculating forces on the base plate from structural analysis, checking geometric requirements for bolt spacing and edge distances, and verifying the base plate and bolts have sufficient capacity for bearing pressure, shear, tension and a combined shear and tension check.

Uploaded by

mathewsujith31
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 15

Design of base plate

Project/Client :-
S.No Calculations References
1 Design forces
Factored Axial load Pu = 162 KN From analysis
Nature of axial load = Tension
Factored Shear force Fy = 92 KN
Dia of anchor bolts (HT bolts) = M 20 mm
No of bolts = 8 Nos
Grade of bolts = 8.8
Ultimate Tensile strength of bolt fu = 800 Mpa
Ultimate Tesile strength of plate fcu = 250 Mpa
Yield stress of plate fy = 250 Mpa
Yield stress of bolt fyb = 250 Mpa
Cube compressive strength of concrete fck = 35 Mpa
2 Geometric properties
Column section = ISMC BOX
Depth of section = 200 mm
Width of flange = 100 mm
Clearence of holes = 2 mm
Dia of holes = Nominal dia of bolt + clearence = 22 mm
Minimum Edge distance = 33 mm Clause 10.2.4
Maximum edge distance = 12tε IS:800:2007
= 192 mm
1/2
ε = (250/fy)
= 1
Edge distance provided = 50 mm
O.K

100 100

16
400
50 300 50
100

150
200

100

400

200
100
100
400

Minimum spacing of bolts (2.5 d) = 50 mm Clause 10.2.2 &


Maximum spacing of bolts (lesser of 32t or 300) = 300 mm 10.2.3
Spacing of bolt provided = 300 mm IS:800:2007
O.K
3 Check for base pressure
Bearing pressure of plate w = Pu/Ap
= 1.01 Mpa
Allowable bearing pressure = 0.6fck
= 21 Mpa
Safe
4 Check for Minimum Thickness of base plate Clause 7.4.3.1
Thickness of plate required IS:800:2007

ts  2 .5 w ( a 2  0 .3b 2 ) mo / fy  tf
ts = 14.72 mm
Thickness of plate required = 16 mm
Safe
4 Check for shear capacity of bolts Clause 10.3.3
Design shear strength of bolt, Vdsb = Vnsb/‫ע‬mb IS:800:2007
Nominal shear capacity, Vnsb
Vnsb = 261.05 KN
Vdsb = 208.84 KN

Calculated shear force per bolt Vd = 11.5 KN


Safe
5 Check for bearing capacity of bolts Clause 10.3.4
Design bearing strength of bolts Vdpb = Vnpb/‫ע‬mb IS:800:2007
Vnpb = 2.5kb d t fu
kb = 0.76
Vnpb = 486.4 KN
Vdpb = 389.12 KN
Calculated bearing strength of bolt Vb = 20.25 KN
Safe
6 Check for tension capacity of bolts
Design tension capacity of bolt Tdp = Tnp/‫ע‬mb
Nominal Tensile capacity of bolt
Tnp = 0.9fubAn<fybAsb(‫ע‬mb/‫ע‬mo)
0.9fubAn = 180.86 Mpa
fybAsb(‫ע‬mb/‫ע‬mo) = 89.2 Mpa
Nominal Tensile capacity of bolt Tnp = 89.2 Mpa
Design tension capacity of bolt Tdp = 71.36 Mpa
Calculated tension per bolt T = 20.25 Mpa
Safe
7 Check for combined shear and tension

11.5 20.25
+ = 0.3133 < 1.0
389.12 71.36
Safe

You might also like