Scribd Logo
Upload

Welcome to Scribd!

  • 74 views

    Harmonic Filter Controlcircuit Operation

    Uploaded by

    dhaneesh22
    The document describes the operation of a harmonic filter control circuit. It discusses three contactors - 8.1 for switching the filter on and off, 8.2 for filter adaptation when one bogie is isolated, and 8.41 for discharging the harmonic filter capacitors through a discharge resistor. Contactors 8.1 and 8.41 are controlled by control electronics to close and open the filter circuit as needed based on throttle position and isolation of traction converters.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd

    Harmonic Filter Controlcircuit Operation

    Uploaded by

    dhaneesh22
    74 views1 page
    The document describes the operation of a harmonic filter control circuit. It discusses three contactors - 8.1 for switching the filter on and off, 8.2 for filter adaptation when one bogie is isolated, and 8.41 for discharging the harmonic filter capacitors through a discharge resistor. Contactors 8.1 and 8.41 are controlled by control electronics to close and open the filter circuit as needed based on throttle position and isolation of traction converters.

    Original Title

    HARMONIC FILTER CONTROLCIRCUIT OPERATION

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document describes the operation of a harmonic filter control circuit. It discusses three contactors - 8.1 for switching the filter on and off, 8.2 for filter adaptation when one bogie is isolated, and 8.41 for discharging the harmonic filter capacitors through a discharge resistor. Contactors 8.1 and 8.41 are controlled by control electronics to close and open the filter circuit as needed based on throttle position and isolation of traction converters.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    74 views1 page

    Harmonic Filter Controlcircuit Operation

    Uploaded by

    dhaneesh22
    The document describes the operation of a harmonic filter control circuit. It discusses three contactors - 8.1 for switching the filter on and off, 8.2 for filter adaptation when one bogie is isolated, and 8.41 for discharging the harmonic filter capacitors through a discharge resistor. Contactors 8.1 and 8.41 are controlled by control electronics to close and open the filter circuit as needed based on throttle position and isolation of traction converters.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    of 1

    HARMONIC FILTER CONTROLCIRCUIT OPERATION

    Filter ON/OFF: -

    To switch ON/ OFF filter circuit Contactor (8.1) is used whose coil is energised through Converter
    Control Electronics (415 WG/1). With Key switch in Driving (D) position, Control Electronics contactor
    218 closes and extends supply to potential 5101B, A through MCB 127.1 and to coil of contactor 8.1
    through converter Control Electronics 415 and NC contact of Contactor Discharging Resistance
    (8.41).

    Control electronics controls the closing of filter ON/OFF contactor in the following manner: -

    1. With VCB closed and Reversor position selected, the filter ON / OFF Contactor (8.1) will close
    when TE/BE throttle is moved from Zero Position to any other position.
    2. After wards whenever Throttle is brought to Zero with VCB closed the filter contactor will
    remain close. However, if this situation persists for more than 5 minutes then Filter
    Contactor (8.1) opens Discharger Contactor (8.41) closes for 120 M seconds. Filter ON/OFF
    (8.1) will remain close when TE/BE throttle is moved again. With contactor energised, its
    auxiliary contacts 8.1 connected between potential 2801A and 2861A, B closes and this
    message is taken by converter control electronics connected at potential 2861A, B.

    Filter Adaptation:

    Contactor 8.2 is used for Filter adaptation, which is closed when both the bogies are in operation
    and open when one bogie is isolated. Contactor coil is energised through converter control
    electronics (415) With Key Switch in Driving (D) position, Control Electronics Contactor 218 closes
    and supply comes to potential 5101B, A through MCB 127.1 Supply comes to coil of contactor 8.2
    through Converter Control Electronics 415 (5101A, B-2866) Control Electronics will allow supply to
    the contactor coil only when one Traction Converter is isolated

    With contactor energised, its auxiliary contact 8.2 connected between potential 2801A and 2862A, B
    closes and this message is taken by control electronics connected at potential 2861A & B.

    Resistor discharging: -

    Contactor 8.41 is used for resistor discharging, which is closed to discharge harmonic filter capacitor
    (8.41) through Discharge resistor (8.42) and is controlled by control electronics. Supply comes to coil
    of contactor 8.41 through control electronics 415 and normally closed contact (NC) of filter ON/OFF
    contactor 8.1 to ensure that contactor 8.41 is closed only when contactor 8.1 is open. With
    contactor energized, its auxiliary contact 8.41 connected between potential 2801A and 2863A, B
    closes and this message is taken by control Electronics connected at potential 2863A, B.

    You might also like