Industrial Heat Transfer Solutions EN1

INDUSTRIAL
HEAT TRANSFER
SOLUTIONS
CHALLENGE EFFICIENCY
OUR BPHE CONCEPT
The compact Brazed Plate Heat Exchanger (BPHE) is constructed as a plate package
of corrugated channel plates with a filler material between each plate. During the
vacuum-brazing process, the filler material forms a brazed joint at every contact
point between the plates, creating complex channels. The BPHE allows media at
different temperatures to come into close proximity, separated only by channel
plates that enable heat from one media to be transferred to the other with very high
efficiency. The concept is similar to the older plate and frame technology, but
without the gaskets and frame parts.
Simple, flexible, cost-effective BPHEs, counter-current flow is more common

The channel plates form separate circuits for each because it increases efficiency. However, our
media. The number, type and configuration of the BPHEs also employ co-current flow where
channel plates are easy to vary to provide the necessary in applications such as flooded
thermal characteristics required. evaporators.
In a one-pass configuration, the two flows are Easy to install

continuous through each channel plate. In a two- Compared with shell-and-tube models of the same
pass configuration, the two flows are redirected by capacity, our BPHEs are as much as 90% smaller by
special channel plates to give the equivalent of two weight and volume. The BPHE is not only easier to
units connected in series. In addition to one- and transport and handle, but its size means it also
two-pass configurations, we offer a variety of other offers greater system design freedom. Further-
executions and customized solutions. more, connections are available in a wide range of
industry standards.
The flows inside a heat exchanger can be arranged
differently to fulfill different purposes. In our
BPHE principle
Plate Package
Cover
Zero plate
hole
channel
Channel plates plate
Connections
Cover
plate
BENEFITS
Our experience and expertise have been gained all over the world across a wide
range of applications in many different climates. We aim to maximize the
performance and at the same time minimize the amount of material used. This
has environmental benefits, keeps costs down and reduces exposure when
material prices increase. Other benefits of our BPHEs include:
• Tailored: Optimized and customized
• Performance: Reliable, energy-efficient and cost-effective
• Economical: Optimal material usage
• Versatile: Cover a wide range of cooling and heating

capacities
• Competitive: Save space compared with S&T heat

exchangers; withstand high temperature and pressure (no
gaskets), unlike PHE heat exchangers, and have minimal
weight
• Turbulent: Resist scaling and fouling; effective self-

cleaning
• Innovative: Patented solutions, e.g. true dual, double-wall

and asymmetric BPHEs
• Tested: Pressure- and leak-tested. All widely recognized

pressure vessel codes available, e.g. PED, KHK and UL.
• Responsive: Small holdup volume and lower refrigerant

charge
• Standards: Comply with standards such as ISO 9001

(quality) and ISO 14001 (environmental)
OUR BPHES ARE SUPERIOR
Products
• We have the widest range of BPHEs in the world.
High-quality products and services

• We have ISO 9001 and ISO 14001 approval.
• We use SPC (Statistical Process Control) in all steps of our
production.
• We offer full traceability using the unique serial number on
each unit, which enables us to trace the unit to its raw material,
press line and tools, furnace and pressure test equipment.
• We thoroughly investigate claims, and the result whether it is
a line or field failure is always taken seriously. The results of
claims are monitored and followed up statistically to help us
refine our products and processes to avoid them.
Largest production capacity in the world

• Our six factories around the world make it safe to be one of our
customers.
• We use state-of-the-art, fully automated and continuous cut
and press lines in our production.
• We have the highest number of vacuum brazing furnaces
among BPHE manufacturers, which enables us to grow with
our customers.
Assured longest service life

• The raw materials used in our products meet the highest
requirements.
• We carry out periodic burst testing of products taken from
production to ensure we meet our customers' highest
demands.
• Every product we deliver is verified by pressure-testing to a
minimum of 1.5 times its working pressure in each circuit, and
then tested for leaks with helium to ensure detection of even
the smallest leakage. We can detect leakages equivalent to
2.8 g of R22 at 10 bar pressure over a year. All pressure tests
are carried out with compressed air to avoid any
contamination of the product.
• We assure the quality of the vacuum brazing process by
maintaining sufficient material thickness after pressing.
Leading R&D
• We have used Computational Fluid Dynamics (CFD) since the
mid 90's, and we apply the knowledge collected in this tool in
all new product development to optimize
performance and material utilization.
• We produce tools in-house, because we know that a
few hundredths of a millimeter makes a difference to
the product's strength.
• We have our own laboratory for one- and two-phase
applications.
• We have several patented designs and solutions such
as true dual, double wall and air dryer.
• Our dedicated innovation team constantly pushes the
limit.
Top performance you can trust

• We verify all new products in our heat transfer
laboratory before they are released to the market.
• Our calculation software is continuously updated with
the latest laboratory results to ensure it corresponds
to our best current knowledge.
• Our BPHEs deliver documented and reliable
performance in both laminar and turbulent flow
regions.
• Our Corner Passage Pattern utilizes the area around
the heat exchanger ports for heat transfer.
• We use thinner channel plate material to improve the
performance/cost ratio with the same or better ability
to withstand temperature and pressure. Today we
offer standard, medium, high and ultra-high pressure
ratings on our products (30, 42, 45 and 140 bar).
Application and product knowledge

• Our highly skilled staff help customers select the right
model for their individual needs.
• We offer unique expertise acquired across a wide
range of different applications.
Availability
• Our SWEP Software Package (SSP), available from
www.swep.net, makes it easy to select the right
model.
• Most items are available from our centralized
warehouses for fast delivery.
• We offer customized products and connections
through our fast and flexible product configurator.
• We provide automatically generated 3D drawings for
customers to base their designs upon.
INDUSTRIAL APPLICATIONS
Our BPHEs are robust, compact, cost-effective and
reliable over long periods with minimal maintenance – all
vital qualities in industrial applications. We bring
immense international experience to this area, which
includes cooling for oil, laser and electronic systems. Our
BPHEs are also suitable for fuel oil heating and highly
efficient cogeneration (CHP) systems. The BPHE's
flexible design and the ability to customize both the plate
and brazing materials frequently mean unbeatable
performance compared with conventional heat
exchangers.
Oil cooling
Our wide range of BPHEs covers the needs of several
different types of oil cooling e.g. hydraulic, engine and
transmission oil cooling. The reliability and compactness
of our BPHEs are highly valued in oil cooling applications
for engines, wind mills, trains etc, where space for the
heat exchanger is often limited and access for
maintenance is restricted. We have solutions capable to
cope with the various challenges ranging from extreme
viscous transmission oil to Copper free alternatives.
ORC
With our long time experience with large refrigeration
systems and our passion for energy efficient technology
we have been actively involved in the development of the
so called Organic Rankine Cycle systems used for heat
recovery with electrical output from waste heat. With
SWEP as a partner in ORC system applications you can
rely on top class calculation software in combination with
a modular and flexible product portfolio where we now
take the step up to our XXL-range with 6” connections.
Air dryers for air compressors

A common problem in compressed air systems is
condensation, which can cause corrosion and
considerable damage to the equipment using the air. We
provide the solution, with air dryers that prevent the
condensation of water in pneumatic systems. We have
both conventional air dryers and the innovative ADWIS,
the air dryer with integrated separator. With our BPHE
solution, the air is cooled with a refrigerant, the water
vapor is condensed and the moisture is removed all in
one smart, compact and cost-effective unit.
INDUSTRIAL APPLICATIONS
Laser and electronics cooling
Laser and electronic equipment is often cooled using
purified (e.g. deionized) water as a coolant in order to
protect sensitive components. Water in this condition can
have undesirable effects on cooling systems, but we have
a reliable solution. Our nickel-brazed BPHEs meet the
strict demands imposed on materials by deionized water.
Gas systems
Our modular product portfolio offers the opportunity to
customize compact Brazed Plate Heat Exchangers for
applications like natural gas evaporation/condensation
and heat/cooling, as well as industrial use of gases like Air
or Carbon Dioxide, to name a few. The dominating
technology for most of those applications is Shell & Tube
Heat Exchangers which BPHE’s match with compact
measures, high thermal efficiency, easy selections and
short lead times.
Steam
Steam as energy carrier is widely used from process
industry to medical disinfection. The major challenge for a
properly working steam installation is to get the
dimensioning right and thereby match the different
system components. SWEP has a long experience of
Steam System problem solving and offers recognized
accurate heat exchanger selection software. With the
widest range of BPHE’s we can offer combinations for the
most challenging steam systems.
Marine
We offer marine Type Approvals and Classification for a
large variety of applications, like for example fuel heaters,
oil coolers and chillers. All the major Classification
Societies are covered and we offer local production on
several sites worldwide.
MANUFACTURING
For us, the keys to world-class manufacturing are competence and efficiency. Over
the years, we have acquired enormous competence in every aspect of BPHE
manufacturing. This is reflected in the recent opening of our new state-of-the-art
factory in Suzhou, China, which joins our others in Sweden, Switzerland, the United
States, Malaysia and Slovakia.
We use Statistical Process Control (SPC) through- Pressing

out manufacturing to analyze and evaluate the We produce channel plates on automatic integrated
mass of production data and to identify deviations press lines that guarantee consistently high quality.
from control values. Alongside SPC, we use Six This precise and carefully supervised process
Sigma to control defects and Lean manufacturing ensures cost-effective manufacturing and maximal
to minimize waste and optimize work flows. efficiency for each of our BPHEs.
Simulation Brazing
Simulation reinforces R&D creativity and is one of Meticulous brazing is the key to leak-free,
the most important stages in the development of corrosion-resistant heat exchangers. We have
new and existing BPHEs. It accelerates time-to- developed specific brazing programs, with
volume and improves the functionality of new precisely adapted heating and cooling cycles, for
products. every combination of materials and size of heat
exchanger. The most common filler material is
Tooling copper, but nickel is also available.
We precision-mill our own press tools in a totally
integrated CAD/CAM process. This assures quality Testing
and availability at a vital stage in production, and We leak- and pressure-test all heat exchangers
guarantees consistency from series to series. produced, regardless of the model, size and type of
connection. Heat exchangers are normally
Laboratory pressure-tested at 1.5 times the maximum working
We have our own fully developed R&D laboratory, pressure.
which has facilities for testing the heat transfer
capacity of single-phase and two-phase appli-
cations, flow distribution, strength, mechanical and
thermal fatigue performance, etc.
Materials
We have developed far-reaching specifications, and
buy only from certified suppliers. This ensures that
our products have a long and reliable service life
backed up by the traceability demanded by many
third-party approvals. Manufacturing is available in
AISI-316, AISI-304 and SMO-254.
PROFESSIONAL SUPPORT
SSP – the soft way to get hard facts applications: everything from the basics of heat
You can easily identify the optimal BPHE solution transfer to discussions of specific applications.
for your application using our dimensioning
software, SSP, which handles Single phase, Con- Quick selector
denser and Evaporator calculations. Its advanced The Quick selector (available to use free of charge
calculation models use your input data to calculate on www.swep.net) helps you quickly select the
which BPHE will be most efficient for your app- BPHE you need. You can choose from a wide variety
lication. The software is available for download of applications, from a small boiler to a 250 kW
free of charge (see www.swep.net), and is easy to district heating installation.
use thanks to its intuitive user interface.
Cross-reference guide
Quick guides If you are already using a heat exchanger from
The market's most comprehensive handbooks on another company, the Cross-reference guide on
heat transfer are available to download free of www.swep.net will make it easy to change to our
charge from www.swep.net or on CD-ROM from BPHEs. Simply choose your existing manufacturer,
your local SWEP representative. These three digital model and number of plates, and the guide will
handbooks give you first-class technical suggest a suitable replacement from our range.
information on Refrigerant, Heating and Industrial
A BPHE TYPE FOR EVERY NEED
The flexibility of our BPHEs makes them an excellent choice for many applications.
The wide range of plate sizes, plate pattern combinations and connections enables
a virtually unlimited number of combinations. You should be able to find a solution
for your application among the models below.
B-type
The B-type is our original BPHE. Its unique plate geometry, modular design and economical
long manufacturing runs mean the product is easy to customize for many different
applications.
Evaporators
SWEP has developed a wide range of distribution systems, ranging from the V-range to the
latest QA- and QB- versions. These two products are developed for ultra low heat flux and
minimal superheat to enhance evaporation temperature and thereby system efficiency. To
increase efficiency, decrease refrigerant volume and widen capacity range our latest models
also features AsyMatrix © technology with each circuit optimized for its dedicated purpose.
E-type
The E-type is the most efficient BPHE on the market today, with almost all the material
contributing to the heat transfer process. The E-type has been developed for low-pressure
boiler applications (water to water) and moderate temperatures.
M-type (Minex)
The M-type is a hybrid PHE (plate and frame heat exchanger) sealed by gaskets instead of
brazing material. It is a small unit, so it does not need the typical support frame used for
traditional PHEs. Like our BPHEs, the Minex is available in various combinations of materials.
BDW-type
The Double Wall concept is designed for applications requiring high thermal efficiency and no
risk of internal leakage between the two fluids, such as in the food and pharmaceutical
industries. In the unlikely event of a leak, water seeps out between the vented double walls to
the atmosphere, giving a visual indication of a fault.
D-type
Our patented true dual-circuit product put the secondary circuit in contact with two primary
circuits. Even if one primary circuit is shut off, the secondary circuit remains in contact with a
primary circuit. These advantages make the D-type condensers and evaporators the natural
choice for flexible chillers and refrigeration systems as well as three circuit industrial
arrangements with pre-heating possibilities. For three circuit simultaneous operations, SWEP
offers several B-type models with an additional circuit.
ADWIS 5 G2
The original ADWIS just got greater: the new 5-series integrates AsyMatrix®
technology on the refrigerant-to-air side, reducing the increasingly
expensive refrigerant charge while maintaining a low pressure drop on the
air-side. This robust yet cost-effective solution is suitable for flow rates of
up to 100 Nm³/h in a very compact envelope. Other advantages include
stable high performance, convenient drainage and high drying efficiency.
ADWIS 5 G2
PP 12,1 ± 1 Design specification (ISO class 4)
73 ± 1 B A
Air side: P = 7 bar(g), Tdew = 3°C, ∆P = 20 kPa,
Tin = 35°C, Tout = 27°C
F3 Ref.
out Refrigerant side: R134a, Tevap = 0°C, SH = 5K
Design specification (ISO class 5)

Tin = 35°C, Tout = 27°C
192 ± 2
154 ± 1
Refrigerant side: R134a, Tevap = 0°C, SH = 5K
Max working pressure

Air side: 18 bar(g) @ 20°C
Refrigerant side: 35 bar(g) @ 20°C
According to PED
F1
R16 20,1 ± 1
P1 P2
Ref. Air side: 22 bar(g)
in Ø 26 Air 40 ± 1 Air Refrigerant side: 22 bar(g)
out in According to UL
PP formula: 3+[2.17x(NoP A-1)+2.24x(NoP B-1)]+37 or 52

Material specification
Main parts: Stainless steel
Brazing material: Copper
Article Air side Refrigerant side Drainage
numbers connections connections connections
Separator efficiency rate
18530* ISO-G ½” INT Solder 9,65(DD) ½” INT Droplets size: 5 µm = 93%; 10 µm = 99,9 %
18532* NPT ½”-14 INT Solder 9,65(DD) ½” INT
18533* SOLDER 22U Solder 9,65(DD) ½” INT Mounting
18534* ISO-G ¾” A Solder 9,65(DD) ½” INT Stud-bolts available per standard article number: 21727
* NoP available per each article number: 021, 027, 031, 037, 057
Model Flow rate NoP NoP Refrigerant hold-up Total PP

(Nm³/h) A B volume (dm³) ±3% measurement (mm) 60
50
ADWIS 35 - 35 8 13 0,066 82,1
ISO class 4
pressure drop (kPa)
ADWIS 50 35 - 50 10 17 0,088 95,4 40

ADWIS 35
ADWIS 60 50 - 60 10 21 0,088 104,3 30 ADWIS 50
ADWIS 60
ADWIS 80 60 - 80 14 23 0,132 132,5 20 ADWIS 80
ADWIS 100 80 - 100 20 37 0,198 176,9 ADWIS 100
10
ADWIS 35 - 65 8 13 0,066 82,1
ISO class 5
0
ADWIS 50 65 - 85 10 17 0,088 95,4 0 25 50 75 100 125 150 175
ADWIS 60 85 - 95 10 21 0,088 104,3 Flow rate (Nm³/h)
ADWIS 80 95 - 115 14 23 0,132 132,5 This product sheet can be changed without prior notice.
ADWIS 100 115 - 150 20 37 0,198 176,9

Flow rate in accordance with ISO 7183 - 20°C and 0 bar(g)
Air to air package
Separator
Wet air in
Refrigerant to air package
Dry air out
Refrigerant out
Water drainage
Refrigerant in
ADWIS 5 G2
The original ADWIS just got greater: the new 5-series integrates AsyMatrix®
technology on the refrigerant-to-air side, reducing the increasingly
expensive refrigerant charge while maintaining a low pressure drop on the
air-side. This robust yet cost-effective solution is suitable for flow rates of
up to 60 scfm in a very compact envelope. Other advantages include stable
high performance, convenient drainage and high drying efficiency.
ADWIS 5 G2
PP 0.47 ± 0.04
2.87 ± 0.04 B A
Air side: P = 102 psi(g), Tdew = 37.4°F, ∆P = 2.9 psi,
F3 Ref. Tin = 95°F, Tout = 80.6°F
out Refrigerant side: R134a, Tevap = 32°F, SH = 9°F

7.55 ± 0.07
Tin = 95°F, Tout = 80.6°F

6.06 ± 0.04
Refrigerant side: R134a, Tevap = 32°F, SH = 9°F

Air side: 261 psi(g) @ 68°F
Refrigerant side: 507 psi(g) @ 68°F
According to PED
F1
R16 0.79 ± 0.04 P1 P2
Ref. Air side: 319 psi(g)
in Air Air Refrigerant side: 319 psi(g)
Ø 1.02 out 1.57 ± 0.04 in According to UL
PP formula: 0.118+[0.085x(NoP A-1)+0.088x(NoP B-1)]+1.456 or 2.047

18530* ISO-G ½” INT Solder 9,65(DD) ½” INT Droplets size: 0,2 mils = 93%; 0,4 mils = 99,9 %
18532* NPT ½”-14 INT Solder 9,65(DD) ½” INT
18533* SOLDER 22U Solder 9,65(DD) ½” INT Mounting
18534* ISO-G ¾” A Solder 9,65(DD) ½” INT Stud-bolts available per standard article number: 21727
* NoP available per each article number: 021, 027, 031, 037, 057
Model Flow rate NoP NoP Refrigerant hold-up Total PP 8

(scfm) A B volume (ft³) ±3% measurement (in)
7
ADWIS 35 - 20 8 13 0.002 3.2 6
ISO class 4
pressure drop (psi)
ADWIS 50 20 - 30 10 17 0.003 3.8 5 ADWIS 35

ADWIS 60 30 - 35 10 21 0.003 4.1 4 ADWIS 50
3 ADWIS 60
ADWIS 80 35 - 45 14 23 0.005 5.2 ADWIS 80
2
ADWIS 100 45 - 60 20 37 0.007 7.0 ADWIS 100
1
ADWIS 35 - 40 8 13 0.002 3.2
ISO class 5
0
ADWIS 50 40 - 50 10 17 0.003 3.8 0 20 40 60 80 100
ADWIS 60 50 - 55 10 21 0.003 4.1 Flow rate (scfm)
ADWIS 80 55 - 70 14 23 0.005 5.2 This product sheet can be changed without prior notice.
ADWIS 100 70 - 90 20 37 0.007 7.0

Air to air package
Separator
Wet air in
Dry air out
Refrigerant out
Water drainage
Refrigerant in
ADWIS 12 G2
The original ADWIS just got greater: the new 12-series has integrated start plates
to minimize material wastage. This robust yet cost-effective solution is suitable
for flow rates of up to 400 Nm³/h in a very compact envelope. Other advantages
include stable high performance, convenient drainage and high drying
efficiency.
ADWIS 12 G2
PP 27,1 ± 1 Air side: P = 7 bar(g), Tdew = 3°C, ∆P = 20 kPa,
119 ± 1 B A Tin = 35°C, Tout = 27°C
F3 Ref.
out Refrigerant side: R134a, Tevap = 0°C, SH = 5K

290 ± 2
234 ± 1
Tin = 35°C, Tout = 27°C

Refrigerant side: R134a, Tevap = 0°C, SH = 5K

Air side: 18 bar(g) @ 20°C
R22 F1 27,1 ± 1
P1
Refrigerant side: 39 bar(g) @ 20°C
P2
Ø 34 63 ± 1 According to PED
Ref.
in Air Air
out in Air side: 16 bar(g)
Refrigerant side: 31 bar(g)
PP formula: 4+2.34xNoP(A+B)+72 or 102 According to UL
18489-* Solder 42U Solder 12,8 ¾” INT

18496-* ISO-G 1” INT Solder 12,8 ¾” INT
Droplets size: 5 µm = 93%; 10 µm = 99,9 %
18535-* Solder 35,1 Solder 12,8 ¾” INT
18536-* ISO-G 1 ¼” INT Solder 12,8 ¾” INT Mounting
18537-* NPT 1 ¼”-11 ½ INT Solder 12,8 ¾” INT
Stud-bolts available per standard article number: 21712
18538-* NPT 1”-11 ½ INT Solder 12,8 ¾” INT
18539-* Solder 42U Solder 22U ¾” INT
* NoP available per each article number: 031, 037, 045, 055, 067, 081
50
45
(Nm³/h) A B volume (dm³) ±3% measurement (mm)
40
ADWIS 150 100 - 150 14 17 0,378 148,5 35
pressure drop (kPa)
ADWIS 150
30
ADWIS 200 150 - 200 16 21 0,441 162,6 ADWIS 200
ISO class 4
25 ADWIS 250
ADWIS 250 200 - 250 18 27 0,504 181,3
20 ADWIS 300
ADWIS 300 200 - 300 22 33 0,630 234,7 15 ADWIS 350
ADWIS 350 300 - 350 26 41 0,756 262,8 10 ADWIS 400
ADWIS 400 350 - 400 30 51 0,882 295,5 5
ADWIS 150 150 - 200 14 17 0,378 148,5 0

ISO class 5
0 100 200 300 400 500

ADWIS 200 200 - 250 16 21 0,441 162,6
Flow rate (Nm³/h)
ADWIS 300 250 - 375 22 33 0,630 234,7
ADWIS 350 375 - 400 26 41 0,756 262,8
This product sheet can be changed without prior notice.
Air to air package
Separator
Wet air in
Dry air out
Refrigerant out
Water drainage
Refrigerant in
ADWIS 12 G2
The original ADWIS just got greater: the new 12-series has integrated start plates
to minimize material wastage. This robust yet cost-effective solution is suitable
for flow rates of up to 235 scfm in a very compact envelope. Other advantages
include stable high performance, convenient drainage and high drying
efficiency.
ADWIS 12 G2
PP 1.06 ± 0.04 Air side: P = 102 psi(g), Tdew = 37.4°F, ∆P = 2.9 psi,
4.68 ± 0.04 B A Tin = 95°F, Tout = 80.6°F
F3 Ref.
out Refrigerant side: R134a, Tevap = 32°F, SH = 9°F

11.41 ± 0.07

9.21 ± 0.04
Tin = 95°F, Tout = 80.6°F

Refrigerant side: R134a, Tevap = 32°F, SH = 9°F

Air side: 261 psi(g) @ 68°F
R22 F1
P1
Refrigerant side: 565 psi(g) @ 68°F
P2
Ref. 1.06 ± 0.04 According to PED
in Ø 1.33
Air 2.48 ± 0.04 Air
out in Air side: 232 psi(g)
Refrigerant side: 449 psi(g)
PP formula: 0.157+0.092xNoP(A+B)+2.834 or 4.015 According to UL
Article Air side Refrigerant side Drainage Main parts: Stainless steel
numbers connections connections connections Brazing material: Copper
18489-* Solder 42U Solder 12,8 ¾” INT

18496-* ISO-G 1” INT Solder 12,8 ¾” INT
Droplets size: 0,2 mils = 93%; 0,4 mils = 99,9 %
18535-* Solder 35,1 Solder 12,8 ¾” INT
18536-* ISO-G 1 ¼” INT Solder 12,8 ¾” INT
Mounting
18537-* NPT 1 ¼”-11 ½ INT Solder 12,8 ¾” INT
Stud-bolts available per standard article number: 21712
18538-* NPT 1”-11 ½ INT Solder 12,8 ¾” INT
18539-* Solder 42U Solder 22U ¾” INT
* NoP available per each article number: 031, 037, 045, 055, 067, 081
8
7
(Scfm) A B volume (ft³) ±3% measurement (in)
6
ADWIS 150 60 - 90 14 17 0.013 5.9
pressure drop (psi)
ADWIS 150
5
ADWIS 200 90 - 120 16 21 0.016 6.4 ADWIS 200
ISO class 4
4 ADWIS 250
ADWIS 250 120 - 145 18 27 0.018 7.1
3 ADWIS 300
ADWIS 300 145 - 175 22 33 0.022 9.2 ADWIS 350
ADWIS 350 175 - 205 26 41 0.027 10.3 2
ADWIS 400
ADWIS 400 205 - 235 30 51 0.031 11.6 1
ADWIS 150 90 - 120 14 17 0.013 5.8 0

ISO class 5
0 50 100 150 200 250

ADWIS 200 120 - 145 16 21 0.016 6.4
Flow rate (scfm)
ADWIS 300 145 - 220 22 33 0.022 9.2
ADWIS 350 220 - 235 26 41 0.027 10.3
Air to air package
Separator
Wet air in
Dry air out
Refrigerant out
Water drainage
Refrigerant in
PRODUCT SHEET
B3
The unique B3 enables efficient heat exchange in applications with small
flows and extreme demands for compactness. Easy to install and use, the
product is small yet flexible, which makes it a particularly good choice for
economizer applications and small water coolers.
Basic specifications
Maximum number of plates (NoP) 60
Max flow 1.6 m³/h (7.04 gpm)
Channel volume 0.0052 dm³ (0.0002 ft³)
Material 304 stainless steel plates, copper brazing
Weight excl. connections 0.11+(0.016*NoP) kg
0.24+(0.035*NoP) lb
Standard dimensions
# MM IN
A 119.40 4.7
B 54.40 2.14
C 91 3.58
D 26 1.02
F 2.00+1.22*(NoP) 0.08+0.05*(NoP)
G 6 0.24
R 15 0.59
E_1 12.10 0.48
www.swep.net | Product No. 100000494, B3H/1P-NC-M | This PDF was generated 2020.06.17
Available connections
Threaded Connection Hose Connection Solder Connection
*For specific dimensions, or information about other types of connections, please contact your SWEP sales representative.
PED Pressure / Temperature Product concept

The Brazed Plate Heat Exchanger (BPHE) is constructed as a plate package
of corrugated channel plates with a filler material between each plate.
During the vacuum brazing process, the filler material forms a brazed joint at
every contact point between the plates, creating complex channels. The
BPHE allows media at different temperatures to come into close proximity,
separated only by channel plates that enable heat from one media to be
transferred to the other with very high efficiency. The concept is similar to
other plate and frame technology, but without the gaskets and frame parts.
3rd party Approvals

Most SWEP products are approved by below listed certification
organizations: Europe, Pressure Equipment Directive (PED) America,
Underwriters Laboratories Inc (UL) Japan, Kouatsu-Gas Hoan Kyoukai (KHK)
UL Pressure / Temperature Additionally SWEP holds approvals from a vast variety of other certification
organizations. For more details please contact your local SWEP
representative. SWEP reserves the right to make changes without prior
notice.
Find product solution - SSP

With SWEP’s unique SSP, the SWEP Software Package, you can do
advanced heat transfer calculations yourself. It’s also easy to choose
connections and generate drawings of the complete product. If you would
like advice, SWEP offers all the service and support you need. Several
SWEP accessories are also available to fulfill additional needs.
Disclaimer
The information and recommendations in regards to the products are
presented in good faith, however, SWEP makes no representations or
warranties as to the completeness or accuracy of the information.
Information is supplied upon the condition that the purchasers will make
their own determination as to the products’ suitability for their purposes prior
to use. Purchasers should note that the properties of the products are both
application and material selection dependent and that products containing
stainless steel are still object to corrosion if used in unsuitable environments.
Standard data is presented, product variants with different data may exist.
Contact your SWEP sales representative for more details. SWEP may
change any data without notice.
www.swep.net | Product No. 100000494, B3H/1P-NC-M | This PDF was generated 2020.06.17
PRODUCT SHEET
B4
The B4 enables efficient heat exchange in applications with extreme
demands for compactness and narrow temperature approaches. Easy to
install and use, the product is small yet flexible, which makes it a
particularly good choice for economizer applications focusing on VRF
and heat pumps. The B4’s mechanical design makes it suitable for high-
pressure refrigerants such as R410A and R32.
1.05+(0.075*NoP) lb
Standard dimensions
# MM IN
A 193.50 7.62
B 76 2.99
C 154 6.06
D 40 1.57
F 4.00+1.02*(NoP) 0.16+0.04*(NoP)
G 6 0.24
R 18 0.71
E_1 20.10 0.79
www.swep.net | Product No. 100000240, B4M/1P-NC-M | This PDF was generated 2020.06.17
Threaded Connection Solder Connection Threaded Ultra High

Approved

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000240, B4M/1P-NC-M | This PDF was generated 2020.06.17
PRODUCT SHEET
B5
The B5 enables efficient heat exchange in applications with small flows
and extreme demands for compactness. Easy to install and use, the
product is small yet versatile, which makes it a good choice for small oil
or water coolers.
Max flow 4 m³/h (17.61 gpm)
Material 316 stainless steel plates, nickel brazing
0.67+(0.088*NoP) lb
Standard dimensions
# MM IN
A 187.50 7.38
B 72.50 2.85
C 154 6.06
D 40 1.57
F 4.30+2.31*(NoP) 0.17+0.09*(NoP)
G 7 0.28
R 16 0.63
E_1 20.10 0.79
www.swep.net | Product No. 100000919, B5H/1P-SN-S | This PDF was generated 2020.06.17
Threaded Connection Solder Connection Threaded Ultra High Combo Connection Weld Connection Hose Connection O-Ring Connection
Approved

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000919, B5H/1P-SN-S | This PDF was generated 2020.06.17
PRODUCT SHEET
B5AS
The B5AS enables efficient heat exchange in applications with small
flows and extreme demands for compactness. Easy to install and use, the
product is small yet versatile, which makes it a good choice for small oil
or water coolers. The B5AS is equipped with our patented AsyMatrix®
technology and delivers more performance from the same size/weight,
enabling space/weight to be saved.
Channel volume 0.022/0.028 dm³ (0.0008/0.0010 ft³)
1.09+(0.097*NoP) lb
Standard dimensions
# MM IN
A 193 7.6
B 76 2.99
C 154 6.06
D 40 1.57
F 4.00+2.17*(NoP) 0.16+0.09*(NoP)
G 6.20 0.24
R 18 0.71
E_1 20.10 0.79
www.swep.net | Product No. 100001016, B5ASH/1P-SC-M | This PDF was generated 2020.06.17
Threaded Ultra High Solder Connection Combo Connection Threaded Connection Hose Connection Weld Connection
Approved

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
B8LAS
The compact B8LAS is a product developed to combine the highest
thermal performance with low pressure drop. With a plate geometry using
that uses AsyMatrix® technology, the unit offers a high efficiency and
versatile solutions for high- efficiency heat pumps and refrigeration
applications.
1.85+(0.130*NoP) lb
Standard dimensions
# MM IN
A 317.70 12.51
B 76.20 3
C 278 10.94
D 40 1.57
F 4.00+1.32*(NoP) 0.16+0.05*(NoP)
G 6.30 0.25
R 18 0.71
E_1 20.10 0.79
www.swep.net | Product No. 100000819, B8LASH/1P-SC-M | This PDF was generated 2020.06.17
Threaded Ultra High Combo Connection Solder Connection Threaded Connection Hose Connection Weld Connection
Approved

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000819, B8LASH/1P-SC-M | This PDF was generated 2020.06.17
PRODUCT SHEET
B8T
The B8T enables efficient heat exchange in applications with small flows
and extreme demands for compactness. Easy to install and use, the
product is small yet versatile, which makes it a good choice for a variety
of one-phase and two-phase applications in many industries.
1.88+(0.165*NoP) lb
Standard dimensions
# MM IN
A 317 12.48
B 76 2.99
C 278 10.94
D 40 1.57
F 4.00+2.24*(NoP) 0.16+0.09*(NoP)
G 7 0.28
R 18 0.71
E_1 20.10 0.79
www.swep.net | Product No. 100000296, B8TH/1P-SC-M | This PDF was generated 2020.06.17
Solder Connection Threaded Ultra High Threaded Connection Hose Connection Combo Connection Weld Connection O-Ring Connection
Approved

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
B9
The B9 is an innovative product that sets new standards in heat
exchanger technology. Based on our AsyMatrix® concept and pioneering
plate technology, the B9 combines high-efficiency technology with
excellent mechanical strength and reliability with a minimum of material
input.
1.10+(0.282*NoP) lb
Standard dimensions
# MM IN
A 378.70 14.91
B 78.70 3.1
C 345 13.58
D 45 1.77
F 2.00+1.29*(NoP) 0.08+0.05*(NoP)
G 3.78 0.15
I 45 1.77
J 5 0.2
K 19.35 0.76
L 9.35 0.37
N 14.35 0.56
R 19.35 0.76
E_1 12.10 0.48
www.swep.net | Product No. 100000979, B9H/1P-SC-U | This PDF was generated 2020.06.17
Threaded Connection Solder Connection

3rd party Approvals

notice.

Disclaimer
Product has crossflow circuits, see Instruction Manual on swep.net.
PRODUCT SHEET
B10T
The B10T delivers efficient heat exchange solutions across a wide
capacity interval, and is quick and simple to adapt for a number of
applications. The product’s compact size, versatility, and excellent heat
transfer make it a perfect choice for both single-phase and refrigerant
applications.
2.54+(0.212*NoP) lb
Standard dimensions
# MM IN
A 289 11.38
B 119 4.69
C 243 9.57
D 72 2.83
F 4.00+2.24*(NoP) 0.16+0.09*(NoP)
G 6 0.24
R 22 0.87
E_1 20.10 0.79
Threaded Connection Threaded Ultra High Solder Connection Connection Plate Combo Connection Hose Connection O-Ring Connection Weld Connection
Approved

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
B10TS- All Stainless

The B10TS delivers efficient heat exchange solutions across a wide
capacity interval, and is quick and simple to adapt for a number of
applications. The product’s compact size, versatility, and excellent heat
transfer make it a perfect choice for both single-phase and refrigerant
applications.
Material 316 stainless steel plates, stainless steel brazing
2.73+(0.267*NoP) lb
Standard dimensions
# MM IN
A 289 11.38
B 119 4.69
C 243 9.57
D 72 2.83
F 4.00+2.39*(NoP) 0.16+0.09*(NoP)
G 6 0.24
R 23 0.91
E_1 20.10 0.79
www.swep.net | Product No. 100001139, B10TSH/1P-SPS-S | This PDF was generated 2020.06.17
Threaded Connection Victaulic Connection Threaded Ultra High Combo Connection Solder Connection
Approved

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100001139, B10TSH/1P-SPS-S | This PDF was generated 2020.06.17
PRODUCT SHEET
B12
The large-port B12 delivers compact heat transfer solutions for
applications with large flows. It is available with different plate patterns to
fulfil various thermal duties across a wide range of fluid viscosities and
densities. The B12 is an excellent choice for demanding steam and air
dryer applications. It can be as a desuperheater in air conditioning and a
CO2 suction gas heat exchanger in refrigeration.
2.47+(0.265*NoP) lb
Standard dimensions
# MM IN
A 287 11.3
B 117 4.61
C 234 9.21
D 63 2.48
F 4.40+2.34*(NoP) 0.17+0.09*(NoP)
G 6 0.24
R 22 0.87
E_1 27.10 1.07
www.swep.net | Product No. 100000975, B12MT/1P-SC-S | This PDF was generated 2020.06.17
Threaded Ultra High Solder Connection Threaded Connection Combo Connection Weld Connection Connection Plate O-Ring Connection Victaulic Connection
Approved

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000975, B12MT/1P-SC-S | This PDF was generated 2020.06.17
PRODUCT SHEET
B15T
The highly efficient B15T has been developed to have maximum thermal
length. Precision optimization allows efficient operation even at extremely
small temperature differences, making the product the obvious choice for
applications demanding high heat flux and improved energy utilization.
2.76+(0.229*NoP) lb
Standard dimensions
# MM IN
A 468 18.43
B 76 2.99
C 432 17.01
D 40 1.57
F 4.00+2.24*(NoP) 0.16+0.09*(NoP)
G 7 0.28
R 18 0.71
E_1 20.10 0.79
Threaded Ultra High Solder Connection Threaded Connection Combo Connection O-Ring Connection Hose Connection Weld Connection
Approved

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
B16
The B16 has been specially designed for one-phase applications, and
has been tailored to cover the capacities and specifications of district
heating substations, radiator circuits, and tap water heating applications
over a wide capacity range. The B16 is also an excellent choice for oil
cooling.
3.25+(0.265*NoP) lb
Standard dimensions
# MM IN
A 376 14.8
B 119 4.69
C 320 12.6
D 63 2.48
F 4.00+2.24*(NoP) 0.16+0.09*(NoP)
G 6 0.24
R 23 0.91
E_1 27.10 1.07
www.swep.net | Product No. 100001102, B16H/1P-SC-S | This PDF was generated 2020.06.17
Solder Connection Threaded Connection Threaded Ultra High Weld Connection Connection Plate Victaulic Connection Combo Connection O-Ring Connection
Approved

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
B17
With pressure requirements for trans critical CO2 applications touching
140 bar, the B17 is the natural choice. The B17 is optimized for high heat
pump capacities (up to 60 kW as a gas cooler and up to 40 kW as an
evaporator). The compact yet lightweight B17 is an excellent choice for
cold chain applications (supermarkets, transport cooling, heat recovery,
economizers), for heat pumps (evaporator and gas cooler) and for mobile
air-conditioning (internal heat exchanger).
9.02+(0.552*NoP) lb
Standard dimensions
# MM IN
A 377 14.84
B 119.50 4.7
C 329 12.95
D 72 2.83
F 12.00+2.00*(NoP) 0.47+0.08*(NoP)
G 2 0.08
R 23.50 0.93
E_1 20.10 0.79
Solder Connection Threaded Ultra High Threaded Connection Combo Connection

Approved

3rd party Approvals

Additionally SWEP holds approvals from a vast variety of other certification
notice.

Disclaimer
PRODUCT SHEET
B18
With pressure requirements for trans critical CO2 applications touching
140 bar, the B18 is the natural choice. The B18 is optimized for high heat
pump capacities (up to 150kW as a gas cooler and up to 60 kW as an
evaporator). The compact yet lightweight B18 is an excellent choice for
cold chain applications (supermarkets, transport cooling, heat recovery,
economizers), and for heat pumps (evaporator and gas cooler).
8.92+(0.552*NoP) lb
Standard dimensions
# MM IN
A 377 14.84
B 119.50 4.7
C 329 12.95
D 72 2.83
F 12.00+2.00*(NoP) 0.47+0.08*(NoP)
G 2 0.08
R 23.50 0.93
E_1 45.10 1.78
Threaded Ultra High Combo Connection Threaded Connection

Approved

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
B20
This ULTRA-COMPACT single circuit product is targeting Heat pumps.
Large ports and innovative plate design enables an effective operating
range up to 20 kW. B20 is delivering 30% less water pressure drop and a
tighter temperature approach compared to similar products on the
market. SWEP’s versatile H pressure products enable efficient heat
exchange in applications requiring high pressures. It is optimized for high
performance with the refrigerant R410A & R32.
Material 316 stainless steel plates, cover plates in 304 stainless steel, copper brazing
2.30+(0.156*NoP) lb
Standard dimensions
# MM IN
A 324 12.76
B 94 3.7
C 268.20 10.56
D 39 1.54
F 6.00+1.46*(NoP) 0.24+0.06*(NoP)
G 5 0.2
H 269.20 10.6
I 20.70 0.81
J 1 0.04
K 19.70 0.78
R 26 1.02
E_1 20.10 0.79
www.swep.net | Product No. 100000657, B20H/1P-NSC-M | This PDF was generated 2020.06.17
Solder Connection Threaded Connection Threaded Ultra High

Approved

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000657, B20H/1P-NSC-M | This PDF was generated 2020.06.17
PRODUCT SHEET
B25T
The B25T delivers efficient heat exchange solutions across a wide
capacity interval. The product’s versatility and excellent heat transfer
make it excellent for demanding water-to-water applications and as a
high-performance condenser.
4.69+(0.391*NoP) lb
Standard dimensions
# MM IN
A 526 20.71
B 119 4.69
C 479 18.86
D 72 2.83
F 4.00+2.25*(NoP) 0.16+0.09*(NoP)
G 6 0.24
R 23 0.91
E_1 20.10 0.79
Threaded Connection Threaded Ultra High Solder Connection Combo Connection Hose Connection O-Ring Connection Weld Connection
Approved

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
B26
The B26 with AsyMatrix® channels is designed to be a high-performance
condenser, which makes it ideal for heat pump applications. Our
AsyMatrix® technology combines high heat transfer efficiency with low
pressure drop, enabling system builders to make more efficient yet more
compact systems. High performance combined with low internal volume
and smaller than expected size makes this BPHE unique in the market
and an excellent choice for numerous applications and functions.
3.29+(0.237*NoP) lb
Standard dimensions
# MM IN
A 376 14.8
B 119 4.69
C 329 12.95
D 72 2.83
F 4.00+1.61*(NoP) 0.16+0.06*(NoP)
G 6 0.24
R 23 0.91
E_1 20.10 0.79
www.swep.net | Product No. 100000266, B26H/1P-SC-M | This PDF was generated 2020.06.17
Threaded Connection Solder Connection Threaded Ultra High Combo Connection Hose Connection Victaulic Connection Weld Connection
Approved

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
B28
This nickel-brazed product is an excellent choice for applications
requiring resistance to both corrosion and demanding high pressures. It
is brazed using a carefully selected nickel alloy to withstand higher
working temperatures.
Material 316 stainless steel plates, nickel brazing
59.42+(0.362*NoP) lb
Standard dimensions
# MM IN
A 562 22.13
B 155 6.1
C 470 18.5
D 63 2.48
F 12.00+2.41*(NoP) 0.47+0.09*(NoP)
P 15 0.59
R 15 0.59
E_1 45.10 1.78
www.swep.net | Product No. 100000458, B28H/1P-SN-H | This PDF was generated 2020.06.17
Solder Connection Threaded Ultra High Weld Connection Threaded Connection Combo Connection Victaulic Connection
Approved

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000458, B28H/1P-SN-H | This PDF was generated 2020.06.17
PRODUCT SHEET
B30
The B30 is an asymmetric cross-flow heat exchanger. It is particularly
suitable for gas-to-liquid applications and for tapping tributary flows from
main streams. With 2½″ piping, it handles water flow of up to 58 m³/h
(255 gpm). It can be used as a suction gas heat exchanger in chillers of
up to 350 kW, as an after cooler for air compressors of up to 175 kW and
as an engine charge air cooler for engines over 1 MW. We have
designed the B30 to offer a robustness which is superior to the normal
BPHE designs, both in respect to static and cyclic loads.
12.96+(0.397*NoP) lb
Standard dimensions
# MM IN
A 243.50 9.59
B 243.50 9.59
C 173.70 6.84
D 174 6.85
F 14.00+2.12*(NoP) 0.55+0.08*(NoP)
G 2 0.08
J 7.50 0.3
K 42.30 1.67
L 35 1.38
N 34.80 1.37
R 35 1.38
E_1 54.20 2.13
www.swep.net | Product No. 100000860, B30L0/1P-SC-H | This PDF was generated 2020.06.17
Victaulic Connection Solder Connection Threaded Connection Combo Connection Flange Connection Weld Connection

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000860, B30L0/1P-SC-H | This PDF was generated 2020.06.17
PRODUCT SHEET
B35
The B35 is ideal for many applications in district heating, heat recovery,
combined heat and power, and engine oil and transmission oil cooling. It
is the perfect choice for efficient heat transfer with a low pressure drop in
systems with up to 2″ piping and 27 m³/h (118.8 gpm) water flow.
Max flow 27.4 m³/h (120.64 gpm)
13.02+(0.750*NoP) lb
Standard dimensions
# MM IN
A 393 15.47
B 243 9.57
C 324 12.76
D 174 6.85
F 8.00+2.34*(NoP) 0.31+0.09*(NoP)
G 3 0.12
R 35 1.38
E_1 27.10 1.07
Threaded Connection Victaulic Connection Solder Connection Combo Connection Flange Connection Weld Connection O-Ring Connection Connection Plate

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
B35T
The B35T is ideal for many applications in district heating, heat recovery
for industry, HVAC, combined heat & power and engine oil cooling. It is
the perfect choice for efficient heat transfer with a low pressure drop in
systems with up to 2½″ piping and 58 m³/h (255 gpm) water flow.
34.73+(0.564*NoP) lb
Standard dimensions
# MM IN
A 393 15.47
B 243 9.57
C 324 12.76
D 174 6.85
F 22.00+2.26*(NoP) 0.87+0.09*(NoP)
G 0 0
R 35 1.38
E_1 27.10 1.07
www.swep.net | Product No. 100000109, B35TH0/1P-SC-M | This PDF was generated 2020.06.17
Threaded Connection Solder Connection Flange Connection Weld Connection Victaulic Connection

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000109, B35TH0/1P-SC-M | This PDF was generated 2020.06.17
PRODUCT SHEET
B50
The modular B50 is used in many demanding applications, such as
district heating, steam, oil coolers and different industrial applications.
With three different plate combinations and 2½″ connections, it provides
an efficient solution for performances of up to 56 m³/h (246 gpm) water
flow.
29.75+(0.941*NoP) lb
Standard dimensions
# MM IN
A 525 20.67
B 243 9.57
C 441 17.36
D 159 6.26
F 21.40+2.34*(NoP) 0.84+0.09*(NoP)
G 2 0.08
R 35 1.38
E_1 54.20 2.13
www.swep.net | Product No. 100000850, B50H/D-SC-S | This PDF was generated 2020.06.17
Flange Connection Threaded Connection Solder Connection Victaulic Connection Connection Plate

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000850, B50H/D-SC-S | This PDF was generated 2020.06.17
PRODUCT SHEET
B56
The B56 is specially adapted to offer efficient heat transfer in heating and
industrial applications. Equipped with our patented AsyMatrix®
technology it offers a versatile fit especially for district heating- and oil
cooling applications.
Max flow 76.2 m³/h (335.50 gpm)
28.56+(0.924*NoP) lb
Standard dimensions
# MM IN
A 525 20.67
B 243 9.57
C 430 16.93
D 148 5.83
F 14.00+2.44*(NoP) 0.55+0.1*(NoP)
G 2.50 0.1
R 48 1.89
E_1 54.20 2.13
Threaded Connection Flange Connection Victaulic Connection Solder Connection Weld Connection Connection Plate

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
B60
The optimized B60 is the market’s leading product for gas/liquid
applications. It provides optimal heat transfer where the media have
extreme volume differences. The asymmetric design of the channel plates
enables the fluids to have different flow rates. The exchanger is also
designed for optimal cross flow.
Max flow 76.2 m³/h (335.50 gpm)
35.62+(1.036*NoP) lb
Standard dimensions
# MM IN
A 374 14.72
B 364 14.33
C 284.50 11.2
D 274.50 10.81
F 16.00+2.14*(NoP) 0.63+0.08*(NoP)
G 1.50 0.06
J 7.50 0.3
K 48.50 1.91
L 41 1.61
N 41 1.61
R 49 1.93
E_1 54.20 2.13
Threaded Connection Flange Connection Weld Connection Solder Connection Victaulic Connection Combo Connection Solder Coned
Connection

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
B65
The B65 is the perfect choice for high-capacity applications where the
most robust plate heat exchanger is sought. With different plate
combinations, it offers a solution for the most demanding industrial and
heating applications, and is also a very effective condenser.
Max flow 155.5 m³/h (684.65 gpm)
60.50+(2.271*NoP) lb
Standard dimensions
# MM IN
A 864 34.02
B 363 14.29
C 731 28.78
D 231 9.09
F 17.00+2.32*(NoP) 0.67+0.09*(NoP)
G 0.50 0.02
R 67 2.64
E_1 54.10 2.13
Weld Connection Solder Connection Flange Connection Threaded Connection Victaulic Connection Combo Connection Connection Plate

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
B80
The B80 is our medium-size high-capacity model. It is the perfect choice
for most types of low-capacity chiller applications and high-performance
heat pumps. It covers a wide capacity range in district heating
substations and is a proven oil cooler for compressors and hydraulics.
4.61+(0.362*NoP) lb
Standard dimensions
# MM IN
A 526 20.71
B 119 4.69
C 470 18.5
D 63 2.48
F 4.00+2.24*(NoP) 0.16+0.09*(NoP)
G 6 0.24
R 23 0.91
E_1 27.10 1.07
Solder Connection Threaded Connection Weld Connection Victaulic Connection Combo Connection Threaded Ultra High O-Ring Connection
Approved

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
B80AS
The B80AS is built on the successful 80 platform and adds the
advantages of our patented AsyMatrix® technology to deliver increased
thermal performance and reduced pressure drop. The B80AS shares the
same physical aspects of the current B80, enabling it to be used as a
drop-in improvement in existing systems. Target applications for the
B80AS are in heat pump and chiller installations, and in transmission oil
cooling and heating.
4.61+(0.362*NoP) lb
Standard dimensions
# MM IN
A 526 20.71
B 119 4.69
C 470 18.5
D 63 2.48
F 4.00+2.24*(NoP) 0.16+0.09*(NoP)
G 6 0.24
R 23 0.91
E_1 27.10 1.07
Threaded Connection Solder Connection Combo Connection Threaded Ultra High Weld Connection Victaulic Connection
Approved

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
B85
The B85 is a highly efficient heat exchanger with a higher thermal
performance than any comparable product. The B85 is the perfect choice
for high-performance condensers and demanding heat transfer
requirements. The large ports enable it to cope with high capacities. A
smaller pressing depth, compared with previous generations, makes the
B85 more compact with a higher performance.
4.60+(0.301*NoP) lb
Standard dimensions
# MM IN
A 526 20.71
B 119 4.69
C 470 18.5
D 63 2.48
F 4.00+1.84*(NoP) 0.16+0.07*(NoP)
G 6 0.24
R 23 0.91
E_1 27.10 1.07
Solder Connection Victaulic Connection Threaded Connection Threaded Ultra High Combo Connection Weld Connection Hose Connection
Approved

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
B86
The B86 is a highly efficient heat exchanger with higher thermal length
than previous generations. It is a perfect choice for high efficient tap
water heating and premium condenser applications and offers an
optimized heat transfer and reduced hold up volume.
4.60+(0.301*NoP) lb
Standard dimensions
# MM IN
A 526 20.71
B 119 4.69
C 470 18.5
D 63 2.48
F 4.00+1.68*(NoP) 0.16+0.07*(NoP)
G 6 0.24
R 23 0.91
E_1 20.10 0.79
Victaulic Connection Threaded Connection Hose Connection Solder Connection Threaded Ultra High Combo Connection
Approved

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
B120T
The B120T has been specially developed to operate in demanding
heating and industrial applications, typically water-water applications and
oil coolers. The product has contributed to the rapid switch to BPHEs
from traditional gasket plate heat exchangers and shell-and-tube
solutions. It is widely used as a condenser in air conditioning and
refrigeration.
Max flow 27.4 m³/h (120.64 gpm)
18.36+(0.891*NoP) lb
Standard dimensions
# MM IN
A 525 20.67
B 243 9.57
C 456 17.95
D 174 6.85
F 10.00+2.29*(NoP) 0.39+0.09*(NoP)
G 4 0.16
R 35 1.38
E_1 27.10 1.07
Solder Connection Threaded Connection Victaulic Connection Combo Connection Weld Connection Flange Connection O-Ring Connection

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
B185
The demand for natural refrigerants such as CO2 is increasing. With
pressure requirements for transcritical CO2 applications touching 140
bar, the B185 is the natural choice. The B185 is optimized for high heat
load capacities (up to 350 kW as a gas cooler). The compact yet
lightweight B185 is suitable for cold-chain applications (hypermarkets,
supermarkets, heat recovery) and heat pumps (evaporators, gas
coolers).
Max flow 38.8 m³/h (170.83 gpm)
24.98+(0.963*NoP) lb
Standard dimensions
# MM IN
A 425.20 16.74
B 203.20 8
C 354 13.94
D 126 4.96
F 18.00+2.00*(NoP) 0.71+0.08*(NoP)
G 0 0
H 342 13.46
J 6 0.24
K 35.60 1.4
N 41.60 1.64
R 41.60 1.64
E_1 45.10 1.78
Threaded Ultra High Combo Connection

Approved

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
B200T
The B200T is a condenser operating across a wide capacity interval. The
product is perfect for solutions that require compactness and efficiency,
and is an effective alternative to shell-and-tube exchangers.
Max flow 43.7 m³/h (192.41 gpm)
20.84+(0.882*NoP) lb
Standard dimensions
# MM IN
A 525 20.67
B 243 9.57
C 448.50 17.66
D 163.50 6.44
F 10.00+2.29*(NoP) 0.39+0.09*(NoP)
G 4 0.16
H 450 17.72
I 171 6.73
J 4.50 0.18
K 42 1.65
N 37.50 1.48
R 35 1.38
E_1 54.20 2.13
Solder Connection Combo Connection Threaded Connection Weld Connection Flange Connection Victaulic Connection

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
B220
B220 is a compact but highly efficient Brazed Plate Heat Exchanger,
which offers great heat transfer efficiency at a low cost. One main
application is high efficiency tap water heating, but it can also be used in
other single-phase applications such as oil cooling, space heating and
desuperheaters. Thanks to its two-stack feature, the thermal length can
be varied, and it is possible to get a tailored top performing product for
each application.
11.68+(0.708*NoP) lb
Standard dimensions
# MM IN
A 524 20.63
B 202 7.95
C 442 17.4
D 120 4.72
F 6.00+1.73*(NoP) 0.24+0.07*(NoP)
G 4 0.16
R 41.60 1.64
E_1 54 2.13
Threaded Connection Victaulic Connection Solder Connection Flange Connection

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
B250AS
Our B250AS is a high-efficiency single-circuit condenser, specially
developed for water-cooled chiller and heat pump applications. Its large
ports and asymmetric plate design deliver an effective operating range of
80-250 kW. Our AsyMatrix® plate pattern improves heat transfer while
reducing water pressure drop and refrigerant charge.
18.52+(0.743*NoP) lb
Standard dimensions
# MM IN
A 620 24.41
B 202 7.95
C 538 21.18
D 112 4.41
F 14.00+1.91*(NoP) 0.55+0.08*(NoP)
G 0 0
H 530 20.87
I 120 4.72
K 45 1.77
N 45 1.77
R 45 1.77
E_1 27.10 1.07
www.swep.net | Product No. 100000180, B250ASH/1P-NSC-H | This PDF was generated 2020.06.17
Threaded Connection Solder Connection Victaulic Connection Combo Connection

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000180, B250ASH/1P-NSC-H | This PDF was generated 2020.06.17
PRODUCT SHEET
B315
315 product is equipped with 3” ports in a compact envelope, based on
open yet strong internal design, facilitating low pressure drop and high
flow rates in a compact format also with full utilization of the plate area. A
robust solution in stainless steel, which brings lifetime and quality
advantages. Optimized for air dryer applications, heat recovery coming
from chillers and various industrial applications, also suitable for oil-
cooling at large temperature approaches.
Max flow 76.2 m³/h (335.50 gpm)
15.39+(0.688*NoP) lb
Standard dimensions
# MM IN
A 392.50 15.45
B 242.50 9.55
C 298 11.73
D 148 5.83
F 10.00+2.86*(NoP) 0.39+0.11*(NoP)
G 4 0.16
R 47 1.85
E_1 54.20 2.13
www.swep.net | Product No. 100000880, B315M/1P-SC-S | This PDF was generated 2020.06.17
Solder Connection Victaulic Connection Weld Connection Threaded Connection

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
B320LT
The B320LT envelope offers efficient solutions in many demanding
applications, such as district heating, oil coolers and different industrial
applications. This product is part of SWEPs range for larger capacities
which offers a flexible thermal length through optimizing the plate
arrangement which provides a great application fit combining high
thermal efficiency and expanded capacity reach.
Max flow 76.2 m³/h (335.50 gpm)
28.89+(0.952*NoP) lb
Standard dimensions
# MM IN
A 525 20.67
B 243 9.57
C 430 16.93
D 148 5.83
F 14.00+2.57*(NoP) 0.55+0.1*(NoP)
G 2 0.08
R 48 1.89
E_1 54 2.13
www.swep.net | Product No. 100001194, B320LTH/1P-SC-M | This PDF was generated 2020.06.17
Threaded Connection Victaulic Connection Solder Connection Flange Connection

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100001194, B320LTH/1P-SC-M | This PDF was generated 2020.06.17
PRODUCT SHEET
B400T
The B400T has been developed to work extremely effectively at high
capacities, enabling compact solutions in demanding chiller applications.
34.02+(1.409*NoP) lb
Standard dimensions
# MM IN
A 694 27.32
B 304 11.97
C 601 23.66
D 205.50 8.09
F 18.00+2.29*(NoP) 0.71+0.09*(NoP)
G 0 0
H 597 23.5
I 215.50 8.48
J 3.50 0.14
K 52 2.05
N 47.50 1.87
O 2 0.08
R 44 1.73
V 150 5.91
E_1 54.10 2.13
Solder Connection Threaded Connection Victaulic Connection Weld Connection Flange Connection Combo Connection

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
B427
The efficient B427 has four different plate types, making it easy to adapt
for a wide variety of heating and industrial applications. With 4″
connections it handles up to 156 m³/h (686 gpm) water flow.
Max flow 155.5 m³/h (684.65 gpm)
48.26+(1.301*NoP) lb
Standard dimensions
# MM IN
A 694 27.32
B 304 11.97
C 567 22.32
D 179 7.05
F 22.00+2.29*(NoP) 0.87+0.09*(NoP)
G 0 0
R 44 1.73
E_1 54.10 2.13
Weld Connection Flange Connection Victaulic Connection Hose Connection Threaded Connection Combo Connection Solder Connection Connection Plate

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
B439
The efficient B439 is designed for high heat transfer. It has two plate
types, which can also be used together, suitable for a wide range of
heating, cooling, and industrial applications. With 4″ connections it
handles up to 156 m³/h (686 gpm) water flow.
Max flow 155.5 m³/h (684.65 gpm)
34.68+(1.962*NoP) lb
Standard dimensions
# MM IN
A 979 38.54
B 304 11.97
C 854 33.62
D 179 7.05
F 12.00+2.29*(NoP) 0.47+0.09*(NoP)
G 6 0.24
R 44 1.73
E_1 54.10 2.13
Threaded Connection Weld Connection Flange Connection Solder Connection Victaulic Connection

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
B500T
The B500T has been designed to work extremely efficiently as a high-
capacity condenser in various systems such as modular chillers and
industrial heat pumps.
Max flow 155.5 m³/h (684.65 gpm)
35.35+(1.995*NoP) lb
Standard dimensions
# MM IN
A 979 38.54
B 304 11.97
C 854 33.62
D 179 7.05
F 12.00+2.29*(NoP) 0.47+0.09*(NoP)
G 6 0.24
R 44 1.73
E_1 54.10 2.13
www.swep.net | Product No. 100001006, B500TM/1P-SC-S | This PDF was generated 2020.06.17
Threaded Connection Solder Connection Combo Connection Weld Connection Flange Connection Victaulic Connection

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100001006, B500TM/1P-SC-S | This PDF was generated 2020.06.17
PRODUCT SHEET
B633
The B633 is a high flow capacity BPHE, suitable for a diverse range of
demanding applications, such as condenser and evaporator in power
generation, engine oil cooler, steam condenser, heat recovery in chillers,
or for specific district heating installations. The product offers PHE-like
capacities at high temperature and pressure, without the wear and tear of
parts. Up to 95% of the BPHE material is used to transfer heat, as
opposed to other technologies that use much of their material for support
equipment, shell, or frames. You will benefit from savings in energy
consumption, spare parts, space, transportation and installation.
Max flow 349.9 m³/h (1540.56 gpm)
177.09+(2.698*NoP) lb
Standard dimensions
# MM IN
A 830 32.68
B 537 21.14
C 593 23.35
D 300 11.81
F 61.38+2.39*(NoP) 2.42+0.09*(NoP)
G 0 0
R 119 4.69
E_1 54.10 2.13
www.swep.net | Product No. 100000853, B633L/1P-SC-M | This PDF was generated 2020.06.17
Solder Connection Threaded Connection Combo Connection Flange Connection

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000853, B633L/1P-SC-M | This PDF was generated 2020.06.17
PRODUCT SHEET
B649
The B649 is ideal for district heating and cooling networks, HVAC, and
industrial projects that need an efficient compact BPHE with close
temperature approaches at high operating pressures. The big, one-
phase B649 delivers PHE-like capacities without the wear and tear of
parts. Most of the material (95%) in BPHEs is used to transfer heat,
compared with other technologies that use a lot of material for supports,
frames, etc. This high-capacity BPHE saves money on spare parts,
space, energy consumption, transportation, and installation.
Max flow 349.9 m³/h (1540.56 gpm)
175.15+(4.279*NoP) lb
Standard dimensions
# MM IN
A 1232 48.5
B 537 21.14
C 995 39.17
D 300 11.81
F 45.08+2.09*(NoP) 1.77+0.08*(NoP)
G 0 0
R 118.50 4.67
E_1 54.10 2.13
Flange Connection Threaded Connection Combo Connection Solder Connection Weld Connection Victaulic Connection

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
BDW16DW
This double-wall product is designed for applications requiring high
thermal efficiency, minimal leakage, and improved leak detection. The
design offers the same compactness and thermal performance as other
SWEP BPHEs.
3.42+(0.485*NoP) lb
Standard dimensions
# MM IN
A 377 14.84
B 119.50 4.7
C 329 12.95
D 72 2.83
F 4.00+1.96*(NoP) 0.16+0.08*(NoP)
G 6 0.24
R 23.50 0.93
E_1 20.10 0.79
www.swep.net | Product No. 100000993, BDW16DWH/1P-SC-M | This PDF was generated 2020.06.17
Threaded Ultra High Solder Connection Threaded Connection Combo Connection Hose Connection Victaulic Connection
Approved

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000993, BDW16DWH/1P-SC-M | This PDF was generated 2020.06.17
PRODUCT SHEET
BDW16DW
This double-wall product is designed for applications requiring high
thermal efficiency, minimal leakage, and improved leak detection. The
design offers the same compactness and thermal performance as other
SWEP BPHEs.
120.82+(0.485*NoP) lb
Standard dimensions
# MM IN
A 417 16.42
B 159.50 6.28
C 329 12.95
D 72 2.83
F 90.00+1.96*(NoP) 3.54+0.08*(NoP)
P 39 1.54
R 22 0.87
E_1 81.10 3.19
www.swep.net | Product No. 100000471, BDW16DWH/1P-SC-U | This PDF was generated 2020.06.17
Solder Connection Threaded Ultra High Combo Connection

Approved

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000471, BDW16DWH/1P-SC-U | This PDF was generated 2020.06.17
PRODUCT SHEET
BDW35TDW
The B35TDW targets applications such as boilers for tap water heating,
transformer oil cooling, chiller and refrigeration desuperheaters, and heat
recovery from air compressors. SWEP’s Double Wall technology ensures
that liquids do not mix and makes any internal leaks visible – important
factors in applications where safety is a priority.
27.09+(1.089*NoP) lb
Standard dimensions
# MM IN
A 393 15.47
B 243 9.57
C 309 12.17
D 159 6.26
F 18.00+2.53*(NoP) 0.71+0.1*(NoP)
G 0 0
R 35 1.38
E_1 27.10 1.07
www.swep.net | Product No. 100000402, BDW35TDWM4/1P-SC-H | This PDF was generated 2020.06.17
Threaded Connection Solder Connection Victaulic Connection Flange Connection

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000402, BDW35TDWM4/1P-SC-H | This PDF was generated 2020.06.17
PRODUCT SHEET
SXB16DW
SWEP Sealix®¹ is a new BPHE range that feature a protective layer on
all inner surfaces of the BPHE, resulting in enhanced behavior in terms of
metal leaching, scaling, fouling and corrosion while maintaining thermal
and hydraulic performance. The SXB16DW is a double wall product that
combines Sealix® features with a high thermal efficiency, minimal
leakage, and improved leak detection for water applications. All parts in
contact with water are covered by the SiO₂-based layer.
¹ Sealix is a registered trademark in the EU
3.42+(0.485*NoP) lb
Standard dimensions
# MM IN
A 377 14.84
B 119.50 4.7
C 329 12.95
D 72 2.83
F 4.00+1.96*(NoP) 0.16+0.08*(NoP)
G 6 0.24
R 23.50 0.93
E_1 20.10 0.79
www.swep.net | Product No. 100001300, SXB16DWH/1P-SC-S | This PDF was generated 2020.06.17
Threaded Connection

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100001300, SXB16DWH/1P-SC-S | This PDF was generated 2020.06.17
PRODUCT SHEET
DBD200
The DB200 is a highly effective, versatile True Dual condenser which is
the perfect choice for chillers and heat pump applications. Its advantage
is its ability to deliver full performance at both full and half load.
20.50+(0.882*NoP) lb
Standard dimensions
# MM IN
A 525 20.67
B 243 9.57
C 456 17.95
D 174 6.85
F 10.00+2.29*(NoP) 0.39+0.09*(NoP)
G 4 0.16
M 456 17.95
R 34 1.34
E_1 27.10 1.07
www.swep.net | Product No. 100001093, DBD200H/1P-SC-S | This PDF was generated 2020.06.17
Solder Connection Victaulic Connection Threaded Connection Combo Connection Weld Connection Flange Connection

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100001093, DBD200H/1P-SC-S | This PDF was generated 2020.06.17
PRODUCT SHEET
DBD300
The DB300, equipped with our patented AsyMatrix® technology, is an
asymmetric condenser combining low water pressure drop with high
performance. The DB300 is a highly effective, versatile True Dual
condenser which is the perfect choice for chillers and heat pump
applications. Its advantage is its ability to deliver full performance at both
full and half load.
17.08+(0.741*NoP) lb
Standard dimensions
# MM IN
A 525 20.67
B 243 9.57
C 221 8.7
D 160 6.3
F 10.00+1.89*(NoP) 0.39+0.07*(NoP)
G 4 0.16
I 174 6.85
M 180 7.09
O 2 0.08
R 32 1.26
S 228 8.98
T 210 8.27
E_1 27.10 1.07
www.swep.net | Product No. 100000659, DBD300H/1P-SC-M | This PDF was generated 2020.06.17
Solder Connection Threaded Connection Victaulic Connection Combo Connection

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
DBD310
The DB310 is a highly effective, versatile true dual that is a natural choice
for chillers and heat pump applications. Its advantage is its ability to offer
full performance at both full and partial load. It is optimized for extreme
performance with refrigerants. The product is approved for pressures of
up to 49 bar (710 psi), so it can be used with the majority of current high-
pressure refrigerants, enabling our customers to use the compressor’s
whole envelope. SWEP’s versatile H pressure products enable efficient
heat exchange in applications combining small flows and high pressures.
17.08+(0.741*NoP) lb
Standard dimensions
# MM IN
A 525 20.67
B 243 9.57
C 221 8.7
D 160 6.3
F 10.00+1.91*(NoP) 0.39+0.08*(NoP)
G 4 0.16
I 174 6.85
M 180 7.09
O 2 0.08
R 32 1.26
S 228 8.98
T 210 8.27
E_1 27.10 1.07
www.swep.net | Product No. 100001142, DBD310H/1P-SC-H | This PDF was generated 2020.06.17
Threaded Connection Solder Connection Victaulic Connection

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100001142, DBD310H/1P-SC-H | This PDF was generated 2020.06.17
PRODUCT SHEET
DBD400
the perfect choice for flexible chillers and climate control applications. Its
advantage is its ability to deliver full performance at both full and half load.
25.57+(1.389*NoP) lb
Standard dimensions
# MM IN
A 694 27.32
B 304 11.97
C 604 23.78
D 216 8.5
F 12.00+2.39*(NoP) 0.47+0.09*(NoP)
G 1.50 0.06
M 590 23.23
R 44 1.73
E_1 54.10 2.13
Solder Connection Flange Connection Threaded Connection Victaulic Connection Weld Connection

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
DBD500
the perfect choice for applications such as flexible chillers, industrial heat
pumps, and modular compact reversible chillers. Its advantage is its
ability to deliver full performance at both full and half load.
26.45+(2.050*NoP) lb
Standard dimensions
# MM IN
A 980 38.58
B 304 11.97
C 866 34.09
D 191 7.52
F 12.00+2.29*(NoP) 0.47+0.09*(NoP)
G 6 0.24
M 836 32.91
R 44 1.73
E_1 54.10 2.13
www.swep.net | Product No. 100000851, DBD500M/1P-SC-S | This PDF was generated 2020.06.17
Solder Connection Threaded Connection Victaulic Connection Weld Connection Flange Connection

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000851, DBD500M/1P-SC-S | This PDF was generated 2020.06.17
PRODUCT SHEET
DBD650
The DB650 is a highly effective, versatile true dual that is a natural choice
as condenser for chiller, heat pump and single-phase applications. The
true dual design means excellent performance at both full and partial
load. The product is approved for pressures of up to 49 bar (710 psi), so
it can be used with the majority of current high pressure refrigerants,
enabling our customers to use the compressor’s whole envelope.
The DB650 is a highly effective, versatile true dual that is a natural choice as condenser for
chiller, heat pump and single-phase applications. The true dual design means excellent
performance at both full and partial load. The product is approved for pressures of up to 49
bar (710 psi), so it can be used with the majority of current high pressure refrigerants,
32.16+(2.070*NoP) lb
Standard dimensions
# MM IN
A 744.60 29.31
B 365.60 14.39
C 324 12.76
D 269 10.59
F 14.00+2.43*(NoP) 0.55+0.1*(NoP)
G 2 0.08
I 295 11.61
M 595 23.43
O 6 0.24
S 337 13.27
E_1 54.20 2.13
Solder Connection Victaulic Connection Threaded Connection Weld Connection Flange Connection

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
DBD700
The DB700 is a highly effective, versatile True Dual evaporator optimized
for high performance with high-efficiency refrigerants. It is a perfect
choice for flexible chillers and climate control applications. Its advantage
25.86+(1.326*NoP) lb
Standard dimensions
# MM IN
A 725 28.54
B 302 11.89
C 546 21.5
D 191 7.52
F 14.00+2.38*(NoP) 0.55+0.09*(NoP)
G 0 0
I 207 8.15
M 532 20.94
O 4 0.16
E_1 54.10 2.13
Solder Connection Victaulic Connection Threaded Connection

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
DFD310
The DF310 is a highly effective, versatile true dual that is a natural choice
17.08+(0.754*NoP) lb
Standard dimensions
# MM IN
A 525 20.67
B 243 9.57
C 221 8.7
D 160 6.3
F 10.00+1.91*(NoP) 0.39+0.08*(NoP)
G 4 0.16
I 174 6.85
M 180 7.09
O 2 0.08
R 32 1.26
S 228 8.98
T 210 8.27
E_1 27.10 1.07
www.swep.net | Product No. 100000539, DFD310H/1P-SC-H | This PDF was generated 2020.06.17
Solder Connection Victaulic Connection Combo Connection Threaded Connection

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000539, DFD310H/1P-SC-H | This PDF was generated 2020.06.17
PRODUCT SHEET
DFD300
The DF300 is equipped with our patented AsyMatrix® technology and is
an asymmetric evaporator combining low water pressure drop with high
performance. The DF300 is a highly effective, versatile True Dual
evaporator which is the perfect choice for chillers and heat pump
full and half load.
17.08+(0.767*NoP) lb
Standard dimensions
# MM IN
A 525 20.67
B 243 9.57
C 221 8.7
D 160 6.3
F 10.00+1.89*(NoP) 0.39+0.07*(NoP)
G 4 0.16
I 174 6.85
M 180 7.09
O 2 0.08
R 32 1.26
S 228 8.98
T 210 8.27
E_1 27.10 1.07
www.swep.net | Product No. 100000320, DFD300H/1P-SC-M | This PDF was generated 2020.06.17

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000320, DFD300H/1P-SC-M | This PDF was generated 2020.06.17
PRODUCT SHEET
DFXD310
The DFX310 is a highly effective, versatile true dual that is a natural
choice for chillers and heat pump applications. Its advantage is its ability
to offer full performance at both full and partial load. It is optimized for
extreme performance with refrigerants. The product is approved for
pressures of up to 49 bar (710 psi), so it can be used with the majority of
current high-pressure refrigerants, enabling our customers to use the
compressor’s whole envelope. SWEP’s versatile H pressure products
enable efficient heat exchange in applications combining small flows and
high pressures.
17.08+(0.754*NoP) lb
Standard dimensions
# MM IN
A 525 20.67
B 243 9.57
C 221 8.7
D 160 6.3
F 10.00+1.91*(NoP) 0.39+0.08*(NoP)
G 4 0.16
I 174 6.85
M 180 7.09
O 2 0.08
R 32 1.26
S 228 8.98
T 210 8.27
E_1 27.10 1.07
www.swep.net | Product No. 100000030, DFXD310H/1P-SC-H | This PDF was generated 2020.06.17
Threaded Connection Solder Connection Victaulic Connection

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000030, DFXD310H/1P-SC-H | This PDF was generated 2020.06.17
PRODUCT SHEET
DFXD400
The DFX400 is a highly effective, versatile True Dual that is a natural
choice for high-efficiency chillers and climate control applications.
Optimized as a high-performance evaporator, its advantage is its ability
to offer full performance at both full and half load.
25.57+(1.389*NoP) lb
Standard dimensions
# MM IN
A 694 27.32
B 304 11.97
C 604 23.78
D 216 8.5
F 12.00+2.39*(NoP) 0.47+0.09*(NoP)
G 1.50 0.06
M 590 23.23
R 44 1.73
E_1 54.10 2.13
www.swep.net | Product No. 100000550, DFXD400H/1P-SC-M | This PDF was generated 2020.06.17
Solder Connection Victaulic Connection Solder Coned Threaded Connection Flange Connection
Connection

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
DFXD650
The DFX650 is a highly effective, versatile true dual that is a natural
choice as evaporator for chiller- and heat pump applications. DFX650
offer maximum performance for applications targeting low to medium
temperature approach. The true dual design means excellent
performance at both full and partial load. The product is approved for
compressor’s whole envelope.
32.16+(2.102*NoP) lb
Standard dimensions
# MM IN
A 744.60 29.31
B 365.60 14.39
C 324 12.76
D 269 10.59
F 14.00+2.43*(NoP) 0.55+0.1*(NoP)
G 2 0.08
I 295 11.61
M 595 23.43
R 34 1.34
S 337 13.27
E_1 54.20 2.13
Threaded Connection Victaulic Connection Solder Connection Flange Connection Weld Connection

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
DPD200
The DP200 is a highly effective, versatile True Dual evaporator which is
the perfect choice for chillers and heat pump applications. Its advantage
20.52+(0.926*NoP) lb
Standard dimensions
# MM IN
A 525 20.67
B 243 9.57
C 456 17.95
D 174 6.85
F 10.00+2.29*(NoP) 0.39+0.09*(NoP)
G 4 0.16
M 456 17.95
R 34 1.34
E_1 27.10 1.07
www.swep.net | Product No. 100000486, DPD200H/1P-SC-S | This PDF was generated 2020.06.17
Solder Connection Threaded Connection Victaulic Connection Combo Connection Weld Connection

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000486, DPD200H/1P-SC-S | This PDF was generated 2020.06.17
PRODUCT SHEET
DPD300
The DP300 is equipped with our patented AsyMatrix® technology and is
performance. The DP300 is a highly effective, versatile True Dual
evaporator which is the perfect choice for chillers and heat pump
full and half load.
17.08+(0.767*NoP) lb
Standard dimensions
# MM IN
A 525 20.67
B 243 9.57
C 221 8.7
D 160 6.3
F 10.00+1.89*(NoP) 0.39+0.07*(NoP)
G 4 0.16
I 174 6.85
M 180 7.09
O 2 0.08
R 32 1.26
S 228 8.98
T 210 8.27
E_1 27.10 1.07
www.swep.net | Product No. 100001044, DPD300H/1P-SC-M | This PDF was generated 2020.06.17

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
DPD310
The DP310 is a highly effective, versatile true dual that is a natural choice
17.08+(0.754*NoP) lb
Standard dimensions
# MM IN
A 525 20.67
B 243 9.57
C 221 8.7
D 160 6.3
F 10.00+1.91*(NoP) 0.39+0.08*(NoP)
G 4 0.16
I 174 6.85
M 180 7.09
O 2 0.08
R 32 1.26
S 228 8.98
T 210 8.27
E_1 27.10 1.07
www.swep.net | Product No. 100000410, DPD310H/1P-SC-H | This PDF was generated 2020.06.17

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000410, DPD310H/1P-SC-H | This PDF was generated 2020.06.17
PRODUCT SHEET
DPD400
The DP400 is a highly effective, versatile True Dual evaporator optimized
for high performance. It is a perfect choice for flexible chillers and climate
control applications. Its advantage is its ability to deliver full performance
at both full and half load.
25.57+(1.433*NoP) lb
Standard dimensions
# MM IN
A 694 27.32
B 304 11.97
C 604 23.78
D 216 8.5
F 12.00+2.39*(NoP) 0.47+0.09*(NoP)
G 1.50 0.06
M 590 23.23
R 44 1.73
E_1 54.10 2.13
Solder Connection Victaulic Connection Threaded Connection Weld Connection Flange Connection Solder Coned
Connection

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
DPD700
The DP700 is a highly effective, versatile True Dual evaporator optimized
for high performance. It is a perfect choice for flexible chillers and climate
control applications. Its advantage is its ability to deliver full performance
at both full and half load. It also functions as a condenser.
25.86+(1.343*NoP) lb
Standard dimensions
# MM IN
A 725 28.54
B 302 11.89
C 546 21.5
D 191 7.52
F 14.00+2.38*(NoP) 0.55+0.09*(NoP)
G 0 0
I 207 8.15
M 532 20.94
O 4 0.16
E_1 54.10 2.13

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
DSD400
The DS400 is a highly effective, versatile True Dual evaporator which is
25.57+(1.433*NoP) lb
Standard dimensions
# MM IN
A 694 27.32
B 304 11.97
C 604 23.78
D 216 8.5
F 12.00+2.39*(NoP) 0.47+0.09*(NoP)
G 1.50 0.06
M 590 23.23
R 44 1.73
E_1 54.10 2.13
www.swep.net | Product No. 100000194, DSD400H/1P-SC-M | This PDF was generated 2020.06.17
Solder Connection Victaulic Connection Threaded Connection Flange Connection Weld Connection

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000194, DSD400H/1P-SC-M | This PDF was generated 2020.06.17
PRODUCT SHEET
DSD500
The DS500 is a highly effective, versatile True Dual evaporator. It is a
perfect choice for applications such as flexible chillers, industrial heat
pumps, and modular compact reversible chillers. Its advantage is its
ability to deliver full performance at both full and half load.
26.45+(2.116*NoP) lb
Standard dimensions
# MM IN
A 980 38.58
B 304 11.97
C 866 34.09
D 191 7.52
F 12.00+2.29*(NoP) 0.47+0.09*(NoP)
G 6 0.24
M 836 32.91
R 44 1.73
E_1 54.10 2.13
www.swep.net | Product No. 100000697, DSD500M/1P-SC-S | This PDF was generated 2020.06.17
Solder Connection Threaded Connection Victaulic Connection Weld Connection Flange Connection

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000697, DSD500M/1P-SC-S | This PDF was generated 2020.06.17
PRODUCT SHEET
DVD300
The DV300 is equipped with our patented AsyMatrix® technology and is
performance. The DV300 is a highly effective, versatile True Dual
evaporator which is the perfect choice for chiller and heat pump
full and half load.
17.08+(0.767*NoP) lb
Standard dimensions
# MM IN
A 525 20.67
B 243 9.57
C 221 8.7
D 160 6.3
F 10.00+1.89*(NoP) 0.39+0.07*(NoP)
G 4 0.16
I 174 6.85
M 180 7.09
O 2 0.08
R 32 1.26
S 228 8.98
T 210 8.27
E_1 27.10 1.07
www.swep.net | Product No. 100000523, DVD300H/1P-SC-M | This PDF was generated 2020.06.17

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
DVD400
The DV400 is a highly effective, versatile True Dual evaporator which is
25.57+(1.433*NoP) lb
Standard dimensions
# MM IN
A 694 27.32
B 304 11.97
C 604 23.78
D 216 8.5
F 12.00+2.39*(NoP) 0.47+0.09*(NoP)
G 1.50 0.06
M 590 23.23
R 44 1.73
E_1 54.10 2.13
Solder Connection Threaded Connection Victaulic Connection Flange Connection Weld Connection

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
DVD650
The DV650 is a highly effective, versatile true dual that is a natural choice
as evaporator for chiller- and heat pump applications. DV650 offer
maximum performance for applications targeting medium to high
temperature approach. The true dual design means excellent
performance at both full and partial load. The product is approved for
compressor’s whole envelope.
The DV650 is a highly effective, versatile true dual that is a natural choice as evaporator for
chiller- and heat pump applications. DV650 offer maximum performance for applications
targeting medium to high temperature approach. The true dual design means excellent
performance at both full and partial load. The product is approved for pressures of up to 49
bar (710 psi), so it can be used with the majority of current high-pressure refrigerants,

32.16+(2.070*NoP) lb
Standard dimensions
# MM IN
A 744.60 29.31
B 365.60 14.39
C 324 12.76
D 269 10.59
F 14.00+2.43*(NoP) 0.55+0.1*(NoP)
G 2 0.08
I 295 11.61
M 595 23.43
O 6 0.24
S 337 13.27
E_1 54.20 2.13
Threaded Connection Victaulic Connection Solder Connection Flange Connection Weld Connection

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
DVD700
The versatile DV700 has True Dual refrigerant circuits for flexible chiller
and heat pump applications. Our patented AsyMatrix® technology
ensures full performance at both full and part load with low water/brine
pressure drops. The DV700 has a distribution device designed for all
relevant refrigerants. Together with the DP700, it offers a full capacity
range for these applications.
25.86+(1.343*NoP) lb
Standard dimensions
# MM IN
A 725 28.54
B 302 11.89
C 546 21.5
D 191 7.52
F 14.00+2.38*(NoP) 0.55+0.09*(NoP)
G 0 0
I 207 8.15
M 532 20.94
O 4 0.16
E_1 54.10 2.13

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
E5AS
The E5AS, equipped with our patented AsyMatrix® technology, is
optimized for hot tap water production in boilers. Compared with
symmetric heat exchangers, the E5AS presents a much lower pressure
drop. It is also thermally long, making it particularly suitable for
condensing boiler systems. The E5AS has an All-Active plate pack with
front and back plates that give mechanical stability while remaining active
heat transfer plates. This enables the E5AS to transfer more heat using
less material.
0.64+(0.097*NoP) lb
Standard dimensions
# MM IN
A 192 7.56
B 73 2.87
C 154 6.06
D 40 1.57
G 7 0.28
Q 2 0.08
R 16 0.63
E_1 12.10 0.48
www.swep.net | Product No. 100001038, E5ASH/1P-SC-S | This PDF was generated 2020.06.17

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
E5K
The E5K is equipped with our patented AsyMatrix® technology, which
enables high asymmetry between the central heating and tap water sides.
This optimizes heat transfer efficiency in the context of a low pressure
drop on the central heating side. The E5K can also transfer more heat
using less material, thanks to its All-Active plate pack. The pack features
front and back plates that meet the highest mechanical requirements
while remaining active in heat transfer. With its long thermal length, the
E5K is particularly suitable for condensing boiler systems.
0.55+(0.076*NoP) lb
Standard dimensions
# MM IN
A 191 7.52
B 74 2.91
C 154 6.06
D 40 1.57
G 7 0.28
Q 2 0.08
R 17.80 0.7
www.swep.net | Product No. 100001256, E5KH/1P-SC-S | This PDF was generated 2020.06.17

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100001256, E5KH/1P-SC-S | This PDF was generated 2020.06.17
PRODUCT SHEET
E5P
The E5P, equipped with our patented AsyMatrix® technology is
optimized for hot tap water production in boilers. Compared with
symmetric heat exchangers, the E5P presents a much lower pressure
drop. It is also thermally long, making it particularly suitable for
condensing boiler systems. The E5P has an All-Active plate pack with
front and back plates that give mechanical stability while remaining active
heat transfer plates. This enables the E5P to transfer more heat using
less material.
0.49+(0.071*NoP) lb
Standard dimensions
# MM IN
A 190.50 7.5
B 73 2.87
C 154 6.06
D 40 1.57
G 5.90 0.23
Q 2 0.08
R 17.50 0.69
www.swep.net | Product No. 100001041, E5PH/1P-NSC-S | This PDF was generated 2020.06.17
Threaded Connection

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100001041, E5PH/1P-NSC-S | This PDF was generated 2020.06.17
PRODUCT SHEET
E5T
The very compact E5T has been developed to give maximum heat
transfer in wall-hung, non-condensing boiler applications. The unique
construction, with integrated start and end plates, enables the cover
plates to be used for heat transfer to increase cost-effectiveness.
0.63+(0.097*NoP) lb
Standard dimensions
# MM IN
A 192 7.56
B 73 2.87
C 154 6.06
D 40 1.57
G 7 0.28
Q 2 0.08
R 16 0.63
E_1 12.10 0.48
www.swep.net | Product No. 100000698, E5TH/1P-SC-S | This PDF was generated 2020.06.17
Threaded Connection O-Ring Connection Solder Connection Hose Connection Combo Connection

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
E6T
The versatile and very compact E6T delivers improved heat transfer for
the majority of wall-hung, non-condensing boiler applications. The E6T
has an All-Active plate pack with front and back plates that give
mechanical stability while remaining active heat transfer plates. This
enables the E6T to transfer more heat using less material.
0.64+(0.104*NoP) lb
Standard dimensions
# MM IN
A 210 8.27
B 73 2.87
C 172 6.77
D 40 1.57
G 7 0.28
Q 2 0.08
R 16 0.63
E_1 12.10 0.48

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
E8AS
The main application for the E8AS is in heating tap water. The E8AS has
an optimized asymmetric plate geometry that combines extraordinary
thermal efficiency with a low pressure drop. The combination of
exceptional efficiency and maximized material utilization makes the
E8AS the perfect choice for applications demanding high thermal
efficiency and low pressure drop.
1.17+(0.130*NoP) lb
Standard dimensions
# MM IN
A 315 12.4
B 74 2.91
C 278 10.94
D 40 1.57
G 7 0.28
Q 2 0.08
R 17 0.67
E_1 12.10 0.48
Threaded Connection

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
E8LAS
The E8LAS is developed to meet the market’s highest thermal demands
for tap water production. The unique construction, with integrated start
and end plates, combined with high compactness and efficiency means
the E8LAS offers a very versatile solution.
0.93+(0.130*NoP) lb
Standard dimensions
# MM IN
A 316 12.44
B 74 2.91
C 278 10.94
D 40 1.57
G 7 0.28
Q 1.10 0.04
R 17 0.67
E_1 12.10 0.48
www.swep.net | Product No. 100000155, E8LASH/1P-SC-S | This PDF was generated 2020.06.17
Threaded Connection

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000155, E8LASH/1P-SC-S | This PDF was generated 2020.06.17
PRODUCT SHEET
E8T
The versatile and very compact E8T delivers improved heat transfer for
the majority of wall-hung, non-condensing boiler applications. The E8T
has an All-Active plate pack with front and back plates that give
mechanical stability while remaining active heat transfer plates. This
enables the E8T to transfer more heat using less material.
1.07+(0.165*NoP) lb
Standard dimensions
# MM IN
A 315 12.4
B 73 2.87
C 278 10.94
D 40 1.57
G 7 0.28
Q 2 0.08
R 16 0.63
E_1 12.10 0.48
Threaded Connection Solder Connection O-Ring Connection

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
EB6T
The versatile and compact EB6T offers improved heat transfer for the
majority of wall hung, noncondensing boiler applications. The flat cover
plate ads the flexibility for a wide variety of stud bolt options that makes
the EB6T easy to mount in most applications.
0.40+(0.104*NoP) lb
Standard dimensions
# MM IN
A 210 8.27
B 73 2.87
C 172 6.77
D 40 1.57
G 7 0.28
R 17 0.67
www.swep.net | Product No. 100000629, EB6TH/1P-SC-S | This PDF was generated 2020.06.17

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000629, EB6TH/1P-SC-S | This PDF was generated 2020.06.17
PRODUCT SHEET
F80
The F80 is designed as a high-performance evaporator using
refrigerants. The optimization delivers a significant increase in heat flux,
saving energy and giving impressive efficiency gains for high-efficiency
chiller and heat pump systems.
4.61+(0.428*NoP) lb
Standard dimensions
# MM IN
A 526 20.71
B 119 4.69
C 470 18.5
D 63 2.48
F 4.00+2.24*(NoP) 0.16+0.09*(NoP)
G 6 0.24
R 23 0.91
E_1 27.10 1.07
www.swep.net | Product No. 100000251, F80H/1P-SC-M | This PDF was generated 2020.06.17
Solder Connection Victaulic Connection Threaded Connection Threaded Ultra High Hose Connection Weld Connection Combo Connection
Approved

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
F80AS
The F80AS is built on the successful 80 platform and adds the
advantages of SWEP’s patented AsyMatrix® technology, offering
increased thermal performance and reduced pressure drop. The F80AS
is designed as a high-performance evaporator. The optimization
significantly increases heat flux, saving energy and giving impressive
efficiency gains for high-efficiency chiller and heat pump systems.
4.61+(0.428*NoP) lb
Standard dimensions
# MM IN
A 526 20.71
B 119 4.69
C 470 18.5
D 63 2.48
F 4.00+2.24*(NoP) 0.16+0.09*(NoP)
G 6 0.24
R 23 0.91
E_1 27.10 1.07
www.swep.net | Product No. 100001080, F80ASH/1P-SC-M | This PDF was generated 2020.06.17
Solder Connection Threaded Connection Combo Connection Victaulic Connection Threaded Ultra High Weld Connection
Approved

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100001080, F80ASH/1P-SC-M | This PDF was generated 2020.06.17
PRODUCT SHEET
F85
The F85 is a high-performance evaporator with higher efficiency than any
comparable product. The F85 has an integrated distribution system
developed for modern high-pressure refrigerants, making it the preferred
choice for evaporators or reversible condensers targeting high system
performance. The large connection size enables it to cope with high
capacities.
4.60+(0.329*NoP) lb
Standard dimensions
# MM IN
A 526 20.71
B 119 4.69
C 470 18.5
D 63 2.48
F 4.00+1.84*(NoP) 0.16+0.07*(NoP)
G 6 0.24
R 23 0.91
E_1 27.10 1.07
Solder Connection Threaded Connection Threaded Ultra High Victaulic Connection Combo Connection Weld Connection
Approved

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
F120T
The F120T is an evaporator optimized for high performance. It combines
compact size and a specially developed plate pattern in a highly efficient
heat exchanger with a long thermal length. The F120T is the perfect
choice for chillers, heat pumps, and economizers.
Max flow 27.4 m³/h (120.64 gpm)
18.36+(0.935*NoP) lb
Standard dimensions
# MM IN
A 525 20.67
B 243 9.57
C 456 17.95
D 174 6.85
F 10.00+2.29*(NoP) 0.39+0.09*(NoP)
G 4 0.16
R 35 1.38
E_1 27.10 1.07
www.swep.net | Product No. 100000995, F120TH/1P-SC-M | This PDF was generated 2020.06.17
Solder Connection Victaulic Connection Threaded Connection Combo Connection Weld Connection

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
F200T
The F200T is an evaporator optimized for high performance. It combines
heat exchanger with a long thermal length. The F200T is the perfect
Max flow 43.7 m³/h (192.41 gpm)
20.84+(0.926*NoP) lb
Standard dimensions
# MM IN
A 525 20.67
B 243 9.57
C 448.50 17.66
D 163.50 6.44
F 10.00+2.29*(NoP) 0.39+0.09*(NoP)
G 4 0.16
H 450 17.72
I 171 6.73
J 4.50 0.18
K 42 1.65
N 37.50 1.48
R 35 1.38
E_1 54.20 2.13
Solder Connection Combo Connection Victaulic Connection Threaded Connection Flange Connection Weld Connection

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
F250AS
Our F250AS is a high-efficiency single-circuit evaporator, specially
developed for air- and water-cooled reversible chiller applications. Its
large ports and asymmetric plate design deliver an effective operating
range of 80-250 kW. Our AsyMatrix® plate pattern improves heat transfer
while reducing water pressure drop and refrigerant charge.
18.52+(0.771*NoP) lb
Standard dimensions
# MM IN
A 620 24.41
B 202 7.95
C 538 21.18
D 112 4.41
F 14.00+1.91*(NoP) 0.55+0.08*(NoP)
G 0 0
H 530 20.87
I 120 4.72
K 45 1.77
N 45 1.77
R 45 1.77
E_1 27.10 1.07
www.swep.net | Product No. 100000069, F250ASH/1P-NSC-H | This PDF was generated 2020.06.17
Solder Connection Victaulic Connection Threaded Connection Combo Connection

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000069, F250ASH/1P-NSC-H | This PDF was generated 2020.06.17
PRODUCT SHEET
F400T
The F400T is an evaporator for high-efficiency chillers. Other applications
include heat pumps, refrigeration, and industrial chillers. It delivers very
high performance within its capacity range. It combines compactness
with an optimized plate pattern design in a highly efficient heat exchanger
with a long thermal length.
34.02+(1.543*NoP) lb
Standard dimensions
# MM IN
A 694 27.32
B 304 11.97
C 601 23.66
D 205.50 8.09
F 18.00+2.29*(NoP) 0.71+0.09*(NoP)
G 0 0
H 597 23.5
I 215.50 8.48
J 3.50 0.14
K 52 2.05
N 47.50 1.87
O 2 0.08
R 44 1.73
V 150 5.91
E_1 54.10 2.13
Solder Connection Victaulic Connection Solder Coned Weld Connection Threaded Connection Flange Connection
Connection

3rd party Approvals

notice.

Disclaimer
M10
Thanks to an ingenious basic design, M10 combines excellent heat transfer with a compact size
despite the use of rubber gaskets. For applications with small and moderate flows of 12 m3/h (53
usg/min.) M10 offers great opportunities for precise customization. The product can be adapted for
numerous configurations and material combinations, e.g. titanium channel plates.
M10
The Minex -
116 mm (4.57 inch)
72 mm 20.0+ (( 2.33xNP *)x0.98)m m
our little hybrid
(2.83 inch) (0.79+((0.09xNP*)x0.98) inch
23.1 mm The Minex is a hybrid. It's not
(0.91 inch) brazed like a BPHE. It has the
gasket of a PHE (plate-and-
frame heat exchanger), but it's
small, so it does not need the
typical support frame. The
gaskets and the plates can be of
287 mm (11.30 inch)
243 mm (9.57 inch)
various materials. Even if a

costlier, high-performance metal
is required for the heat transfer
surface, the front and back
plates can be made of baser
material to cut costs. The snap-
in-place connections allow the
F1 F2
use of different metals without
the risk of weld deterioration.
They also allow easier assembly.
F3 F4
Easy to choose the
right product solution
Standard connections
For specific dimensions, or information about other types of connections, please With SWEP's unique SSP
contact your SWEP sales representative. BPHE, the SWEP Software
Package, you can do advanced
heat transfer calculations
yourself, and choose the product
solution that suits your
Externally Int. Threaded application best. It's also easy to
with Hex. Ext. choose connec-tions and
generate drawings of the
complete product. If you would
Technical data like advice, or you would like to
Max flow rate 12 m³/h (53 usg/min.) discuss different product
Max working pressure 10 bar (145 psi) solutions, SWEP offers all the
Max working temperature 100°C (212°F), 115°C (239°F) on water/water applications service and support you need.
Min working temperature 0°C (32°F)
Test pressure 15 bar (218 psi) If you would like more infor-
mation about M10 High Pressure
Max. Number of plates 60
or our other products, please
BPHE weight dry (approx.) 6.0+0.11×NP* kg (13.23+0.243×NP* lb)
contact your local SWEP
Hold-up volume: inner circuit 0.042×(NP*/2-1) litre (0.012x(NP*/2-1) gal.)
representative.
Hold-up volume: outer circuit 0.042×NP*/2 litre (0.012xNP*/2 gal.)
Standard connection size 1”
Connection height 33 mm (1.30 inch) or 37 mm (1.46 inch)
*NP = Number of plates
Material
Frame material: Stainless steel or corrosion protected carbon steel
Plate material: EN 10028/7-1.4401 (AlSI 316) or Titanium
Gasket material: Nitrile: NBR(p) or Peroxide cured: EPDM(p)
Connection material: EN 10272-1.4401 (AlSI 316), Carbon steel or Titanium
For additional information please contact your local SWEP representative.

SWEP reserves the right to make changes without prior notice
www.swep.net
PRODUCT SHEET
P80
The P80 is designed as an evaporator using refrigerants. The
optimization delivers a significant increase in heat flux, saving energy and
giving impressive efficiency gains for chiller systems.
4.61+(0.428*NoP) lb
Standard dimensions
# MM IN
A 526 20.71
B 119 4.69
C 470 18.5
D 63 2.48
F 4.00+2.24*(NoP) 0.16+0.09*(NoP)
G 6 0.24
R 23 0.91
E_1 27.10 1.07
www.swep.net | Product No. 100000576, P80H/1P-SC-M | This PDF was generated 2020.06.17
Solder Connection Threaded Connection Combo Connection Victaulic Connection Threaded Ultra High
Approved

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000576, P80H/1P-SC-M | This PDF was generated 2020.06.17
PRODUCT SHEET
P80AS
The P80AS is built on the successful 80 platform and adds the
advantages of SWEP’s patented AsyMatrix® technology, offering
increased thermal performance and reduced pressure drop. The P80AS
is designed as a high-performance evaporator. The optimization
significantly increases heat flux, saving energy and giving impressive
efficiency gains for high-efficiency chiller and heat pump systems.
4.61+(0.428*NoP) lb
Standard dimensions
# MM IN
A 526 20.71
B 119 4.69
C 470 18.5
D 63 2.48
F 4.00+2.24*(NoP) 0.16+0.09*(NoP)
G 6 0.24
R 23 0.91
E_1 27.10 1.07
www.swep.net | Product No. 100001157, P80ASH/1P-SC-M | This PDF was generated 2020.06.17
Solder Connection Threaded Connection Victaulic Connection Combo Connection Threaded Ultra High Weld Connection
Approved

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100001157, P80ASH/1P-SC-M | This PDF was generated 2020.06.17
PRODUCT SHEET
P120T
The P120T is an evaporator optimized for high performance. It combines
heat exchanger with a long thermal length. The P120T is the perfect
Max flow 27.4 m³/h (120.64 gpm)
18.36+(0.935*NoP) lb
Standard dimensions
# MM IN
A 525 20.67
B 243 9.57
C 456 17.95
D 174 6.85
F 10.00+2.29*(NoP) 0.39+0.09*(NoP)
G 4 0.16
R 35 1.38
E_1 27.10 1.07
www.swep.net | Product No. 100000049, P120TH/1P-SC-M | This PDF was generated 2020.06.17
Solder Connection Threaded Connection Victaulic Connection Combo Connection Flange Connection Weld Connection

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
P250AS
Our P250AS is a high-efficiency single-circuit evaporator, specially
developed for air- and water-cooled reversible chiller applications. Its
large ports and asymmetric plate design deliver an effective operating
range of 80-250 kW. Our AsyMatrix® plate pattern improves heat transfer
while reducing water pressure drop and refrigerant charge.
18.52+(0.771*NoP) lb
Standard dimensions
# MM IN
A 620 24.41
B 202 7.95
C 538 21.18
D 112 4.41
F 14.00+1.91*(NoP) 0.55+0.08*(NoP)
G 0 0
H 530 20.87
I 120 4.72
K 45 1.77
N 45 1.77
R 45 1.77
E_1 27.10 1.07
www.swep.net | Product No. 100000972, P250ASH/1P-NSC-H | This PDF was generated 2020.06.17
Solder Connection Victaulic Connection Threaded Connection Combo Connection

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000972, P250ASH/1P-NSC-H | This PDF was generated 2020.06.17
PRODUCT SHEET
P400T
The P400T is an evaporator optimized for high performance. It combines
exchanger with long thermal length. The P400T is the perfect choice for
chillers, heat pumps, and economizers.
34.02+(1.543*NoP) lb
Standard dimensions
# MM IN
A 694 27.32
B 304 11.97
C 601 23.66
D 205.50 8.09
F 18.00+2.29*(NoP) 0.71+0.09*(NoP)
G 0 0
H 597 23.5
I 215.50 8.48
J 3.50 0.14
K 52 2.05
N 47.50 1.87
O 2 0.08
R 44 1.73
V 150 5.91
E_1 54.10 2.13
Solder Connection Threaded Connection Victaulic Connection Solder Coned Weld Connection
Connection

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
P65
The efficient and powerful P65 has been specially developed for
demanding high-capacity cooling applications, in particular advanced
chiller and gas vaporization applications.
Max flow 155.5 m³/h (684.65 gpm)
60.50+(2.359*NoP) lb
Standard dimensions
# MM IN
A 864 34.02
B 363 14.29
C 731 28.78
D 231 9.09
F 17.00+2.32*(NoP) 0.67+0.09*(NoP)
G 0.50 0.02
R 67 2.64
E_1 54.10 2.13
www.swep.net | Product No. 100000699, P65H/1P-SC-S | This PDF was generated 2020.06.17
Weld Connection Combo Connection Solder Connection Victaulic Connection Threaded Connection Flange Connection

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000699, P65H/1P-SC-S | This PDF was generated 2020.06.17
PRODUCT SHEET
QA80
The QA80 evaporator is optimized for heat pump systems using
refrigerants. The injection system is fully integrated with the evaporator,
thereby eliminating any additional assembly operations. The QA80 can
be used with all commercially available system components and uses the
most modern and efficient design on the market. It is available in a wide
number of plate sizes.
4.64+(0.375*NoP) lb
Standard dimensions
# MM IN
A 526 20.71
B 119 4.69
C 470 18.5
D 63 2.48
F 4.00+2.24*(NoP) 0.16+0.09*(NoP)
G 6 0.24
R 23 0.91
E_1 27.10 1.07
www.swep.net | Product No. 100000982, QA80H/1P-SC-M | This PDF was generated 2020.06.17
Solder Connection Threaded Connection

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000982, QA80H/1P-SC-M | This PDF was generated 2020.06.17
PRODUCT SHEET
QA80AS
The QA80AS heat pump evaporator combines the successful 80 platform
with the advantages of our patented AsyMatrix® technology, delivering
increased thermal performance and reduced pressure drop. The fully
integrated Q-pipe distribution system is optimized for high-efficiency heat
pumps and is the most efficient and versatile in the market. The QA80AS
is available in a wide number of plate sizes.
4.64+(0.375*NoP) lb
Standard dimensions
# MM IN
A 526 20.71
B 119 4.69
C 470 18.5
D 63 2.48
F 4.00+2.24*(NoP) 0.16+0.09*(NoP)
G 6 0.24
R 23 0.91
E_1 27.10 1.07
www.swep.net | Product No. 100000027, QA80ASH/1P-SC-M | This PDF was generated 2020.06.17
Solder Connection Threaded Connection Combo Connection Threaded Ultra High

Approved

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000027, QA80ASH/1P-SC-M | This PDF was generated 2020.06.17
PRODUCT SHEET
QB80
The QB80 evaporator is optimized for heat pump systems using
refrigerants. The injection system is fully integrated with the evaporator,
thereby eliminating any additional assembly operations. The QB80 can
be used with all commercially available system components and uses the
most modern and efficient design on the market. It is available in a wide
number of plate sizes.
4.64+(0.375*NoP) lb
Standard dimensions
# MM IN
A 526 20.71
B 119 4.69
C 470 18.5
D 63 2.48
F 4.00+2.24*(NoP) 0.16+0.09*(NoP)
G 6 0.24
R 23 0.91
E_1 27.10 1.07
www.swep.net | Product No. 100000260, QB80H/1P-SC-S | This PDF was generated 2020.06.17
Solder Connection Combo Connection Threaded Connection Threaded Ultra High Victaulic Connection Hose Connection
Approved

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000260, QB80H/1P-SC-S | This PDF was generated 2020.06.17
PRODUCT SHEET
QB80S - All Stainless

The QB80S evaporator combines the successful 80 platform with the
advantages of our SWEP All-Stainless™ products. Developed for
systems demanding 100% stainless steel components, and for high
temperature applications. They can be used with fluids that are corrosive
to copper or for sensitive applications where copper and nickel
contamination must be avoided. SWEP’s unique process technology
enables a compact product with minimal material usage relative to its
mechanical strength. The fully integrated Q-pipe distribution system is
optimized for high-efficient evaporation and is the most efficient and
versatile in the market. The QB80S is available in a wide number of plate
sizes.

4.64+(0.509*NoP) lb
Standard dimensions
# MM IN
A 526 20.71
B 119 4.69
C 470 18.5
D 63 2.48
F 4.00+2.39*(NoP) 0.16+0.09*(NoP)
G 6 0.24
R 23 0.91
E_1 27.10 1.07
www.swep.net | Product No. 100000554, QB80SH/1P-SPS-M | This PDF was generated 2020.06.17

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000554, QB80SH/1P-SPS-M | This PDF was generated 2020.06.17
PRODUCT SHEET
QD20
This ULTRA-COMPACT single circuit product is targeting minichiller and
reversible Air-To-Water heat pumps. Large ports and innovative plate
design enables an effective operating range up to 18 kW QD20 is
delivering 30% less water pressure drop compared to similar products
on the market SWEP’s versatile H pressure products enable efficient
heat exchange in applications requiring high pressures. It is optimized for
high performance with the refrigerant R410A & R32.
2.30+(0.156*NoP) lb
Standard dimensions
# MM IN
A 324 12.76
B 94 3.7
C 268.20 10.56
D 39 1.54
F 6.00+1.46*(NoP) 0.24+0.06*(NoP)
G 5 0.2
H 269.20 10.6
I 20.70 0.81
J 1 0.04
K 19.70 0.78
R 26 1.02
E_1 20.10 0.79
www.swep.net | Product No. 100000492, QD20H/1P-NSC-M | This PDF was generated 2020.06.17

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000492, QD20H/1P-NSC-M | This PDF was generated 2020.06.17
PRODUCT SHEET
QF80S - All Stainless

The QF80S evaporator combines the successful 80 platform with the
advantages of our SWEP All-Stainless™ products. Developed for
systems demanding 100% stainless steel components, and for high
temperature applications. They can be used with fluids that are corrosive
to copper or for sensitive applications where copper and nickel
contamination must be avoided. SWEP’s unique process technology
enables a compact product with minimal material usage relative to its
mechanical strength. The fully integrated Q-pipe distribution system is
optimized for high-efficient evaporation and is the most efficient and
versatile in the market. The QF80S is available in a wide number of plate
sizes.

4.64+(0.509*NoP) lb
Standard dimensions
# MM IN
A 526 20.71
B 119 4.69
C 470 18.5
D 63 2.48
F 4.00+2.39*(NoP) 0.16+0.09*(NoP)
G 6 0.24
R 23 0.91
E_1 27.10 1.07
www.swep.net | Product No. 100000738, QF80SH/1P-SPS-M | This PDF was generated 2020.06.17
Threaded Connection Solder Connection Combo Connection

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000738, QF80SH/1P-SPS-M | This PDF was generated 2020.06.17
PRODUCT SHEET
QN85
The QN85 is a highly efficient evaporator developed to meet the
increasingly demanding requirements of efficient heat pumps. The fully
integrated Q-pipe distribution system is optimized for high-efficiency heat
pumps, and is the most efficient and versatile on the market. The QN85 is
available in a wide range of plate numbers. Large ports enable it to
handle high capacities.
4.63+(0.315*NoP) lb
Standard dimensions
# MM IN
A 526 20.71
B 119 4.69
C 470 18.5
D 63 2.48
F 4.00+1.84*(NoP) 0.16+0.07*(NoP)
G 6 0.24
R 23 0.91
E_1 27.10 1.07
www.swep.net | Product No. 100001017, QN85H/1P-SC-M | This PDF was generated 2020.06.17
Solder Connection Threaded Connection Threaded Ultra High Hose Connection Combo Connection
Approved

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100001017, QN85H/1P-SC-M | This PDF was generated 2020.06.17
PRODUCT SHEET
S400T
The S400T is part of our effective range of evaporators. It functions
extremely effectively at high capacities and creates opportunities for
compact solutions in demanding chiller applications.
34.02+(1.543*NoP) lb
Standard dimensions
# MM IN
A 694 27.32
B 304 11.97
C 601 23.66
D 205.50 8.09
F 18.00+2.29*(NoP) 0.71+0.09*(NoP)
G 0 0
H 597 23.5
I 215.50 8.48
J 3.50 0.14
K 52 2.05
N 47.50 1.87
O 2 0.08
R 44 1.73
V 150 5.91
E_1 54.10 2.13
www.swep.net | Product No. 100000089, S400TH/1P-SC-M | This PDF was generated 2020.06.17
Weld Connection Solder Connection Threaded Connection Flange Connection Victaulic Connection Solder Coned
Connection

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000089, S400TH/1P-SC-M | This PDF was generated 2020.06.17
PRODUCT SHEET
S500T
The S500T is optimized for use in very demanding chiller applications.
The S500T is an excellent choice in modular chillers for air conditioning in
larger facilities such as sport centers and shopping malls.
Max flow 155.5 m³/h (684.65 gpm)
35.35+(2.246*NoP) lb
Standard dimensions
# MM IN
A 979 38.54
B 304 11.97
C 854 33.62
D 179 7.05
F 12.00+2.29*(NoP) 0.47+0.09*(NoP)
G 6 0.24
R 44 1.73
E_1 54.10 2.13
www.swep.net | Product No. 100000624, S500TM/1P-SC-S | This PDF was generated 2020.06.17
Solder Connection Threaded Connection Weld Connection Flange Connection Combo Connection Victaulic Connection

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000624, S500TM/1P-SC-S | This PDF was generated 2020.06.17
PRODUCT SHEET
SXB15T
and hydraulic performance. The SXB15T combines Sealix® features with
excellent heat transfer offering an increased life time solution for water
applications. All parts in contact with water are covered by the SiO₂-
based layer.
1.38+(0.229*NoP) lb
Standard dimensions
# MM IN
A 466 18.35
B 74 2.91
C 432 17.01
D 40 1.57
F 2.00+2.24*(NoP) 0.08+0.09*(NoP)
G 7 0.28
R 17 0.67
E_1 20.10 0.79
www.swep.net | Product No. 100001225, SXB15TH/1P-SC-Y | This PDF was generated 2020.06.17
Threaded Connection

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100001225, SXB15TH/1P-SC-Y | This PDF was generated 2020.06.17
PRODUCT SHEET
SXB25T
and hydraulic performance. The SXB25T combines Sealix® features with
excellent heat transfer offering an increased life time solution for water
applications. All parts in contact with water are covered by the SiO₂-
based layer.
4.69+(0.391*NoP) lb
Standard dimensions
# MM IN
A 526 20.71
B 119 4.69
C 479 18.86
D 72 2.83
F 4.00+2.25*(NoP) 0.16+0.09*(NoP)
G 6 0.24
R 23 0.91
E_1 20.10 0.79
www.swep.net | Product No. 100001213, SXB25TH/1P-SC-S | This PDF was generated 2020.06.17
Threaded Connection

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100001213, SXB25TH/1P-SC-S | This PDF was generated 2020.06.17
PRODUCT SHEET
SXB28
and hydraulic performance. The SXB28 combines Sealix® features with
a specially designed product that covers the capacities and
specifications of district heating substations, radiator circuits and tap
water heating applications over a wide capacity range. All parts in
contact with water are covered by the SiO₂-based layer.
4.61+(0.362*NoP) lb
Standard dimensions
# MM IN
A 526 20.71
B 119 4.69
C 470 18.5
D 63 2.48
F 4.00+2.24*(NoP) 0.16+0.09*(NoP)
G 6 0.24
R 23 0.91
E_1 27.10 1.07
www.swep.net | Product No. 100001267, SXB28H/1P-SC-S | This PDF was generated 2020.06.17
Threaded Connection

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100001267, SXB28H/1P-SC-S | This PDF was generated 2020.06.17
PRODUCT SHEET
SXB85
and hydraulic performance. The SXB85 combines Sealix® features with
a high thermal performance in a compact geometry which offers an
increased life-time solution for high-capacity water applications. All parts
in contact with water are covered by the SiO₂-based layer.
4.60+(0.301*NoP) lb
Standard dimensions
# MM IN
A 526 20.71
B 119 4.69
C 470 18.5
D 63 2.48
F 4.00+1.84*(NoP) 0.16+0.07*(NoP)
G 6 0.24
R 23 0.91
E_1 27.10 1.07
www.swep.net | Product No. 100001299, SXB85H/1P-SC-M | This PDF was generated 2020.06.17
Threaded Connection

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100001299, SXB85H/1P-SC-M | This PDF was generated 2020.06.17
PRODUCT SHEET
SXE8AS
and hydraulic performance. The SXE8AS combines Sealix® features
with excellent heat transfer offering an increased life time solution for
water applications. All parts in contact with water are covered by the
SiO₂-based layer.
1.17+(0.130*NoP) lb
Standard dimensions
# MM IN
A 315 12.4
B 74 2.91
C 278 10.94
D 40 1.57
G 7 0.28
Q 2 0.08
R 17 0.67
E_1 12.10 0.48
www.swep.net | Product No. 100001223, SXE8ASH/1P-SC-S | This PDF was generated 2020.06.17
Threaded Connection

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100001223, SXE8ASH/1P-SC-S | This PDF was generated 2020.06.17
PRODUCT SHEET
SXE8LAS
and hydraulic performance. The SXE8LAS combines Sealix® features
with excellent heat transfer offering an increased life time solution for
water applications. All parts in contact with water are covered by the
SiO₂-based layer.
0.93+(0.130*NoP) lb
Standard dimensions
# MM IN
A 316 12.44
B 74 2.91
C 278 10.94
D 40 1.57
G 7 0.28
Q 1.10 0.04
R 17 0.67
E_1 12.10 0.48
www.swep.net | Product No. 100001224, SXE8LASH/1P-SC-S | This PDF was generated 2020.06.17
Threaded Connection

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100001224, SXE8LASH/1P-SC-S | This PDF was generated 2020.06.17
T-REG Integrated thermoregulator
T-REG
We is an integrated
introduce a new conceptsolution
on anthat combines
integrated an electrical
solution: T-REGheater, a heat
– a plate heat exchanger, and
exchanger combined with
the connecting piping. The concept is designed for applications requiring quick and accurate
an electrical heater for various applications where electrical heating in combination with an additional
temperature control to ensure high productivity and quality (e.g. in the plastic molding industry).
heat exchanger is required (for example for temperature control units in the plastic molding industry). A
compact solution was born which is based on one envelope for a complete range: up to 12 kW heating
Integrated into a single unit, T-REG provides the electric heater that gives the plastic paste the
and
right70 kW* cooling
viscosity, with a footprint
a single-phase of 250×200×80mm
water-to-water – no additional
heat exchanger that coolspiping is needed
the mold between
to harden the the
heat exchanger
plastic, andrequired
and all the the electrical
pipingheater, which
between themakes it toresult
two. The a plugis
and work solution.
a compact, easy-to-install
solution that offers extremely accurate temperature control. The same envelope is used for all
*based
models,on 20°C
whichinlet temperature
offer up to 12and
kW30 l/min cooling
heating andwater
70 kW cooling (based on 20 °C inlet temperature
and 30 l/min cooling water). The unit has a footprint of 250×200×80 mm.
HT SpA - Via Conegliano, 73/B - 31058 Susegana (TV) - Italy - fax +39.0438.62788 SWEP International AB
Domestic Sales: tel. +39.0438.454294 - [email protected] Box 105, SE-261 22 Landskrona, Sweden
Export Sales: tel. +39.0438.454290 - [email protected] Tel. +46 (0)418 40 04 00, Fax -46 (0)418 292 95
www.htspa.it [email protected], www.swep.net
T-REG Integrated thermoregulator
Pilot Indentation
Point Depth 1-1.5 Range Heater code Watt Volt W/Cm²
A T-REG × 24 YT53912 6000 400 6
22.5 Ø 1
148.3 T-REG × 24 YT53914 9000 400 9.1
T-REG × 24 YT53755 12000 400 12.1
20
2 12 R3 20 Range Heater code Watt Volt W/Cm²
95.6
B T-REG × 24
T-REG × 24
YT57432
YT57433
6000
9000
400
400
- 230
- 230
6
9.1
T-REG × 24 YT57434 12000 400 - 230 12.1
243.9
A or B1 B2 B3
380V 400V 420V 220V 230V 240V 230V - 2 Ph
WATT
154
0 5415 6000 6615 5415 6000 6615 6000

8123 9000 9923 8123 9000 9923 9000
10830 12000 13230 10830 12000 13230 12000
77
R2
90
95.6 80
R16.9
R16
70
20.1 136.58 20.1 40 20
60
50
Flow l/min
Heater code: YT53912, YT53914, YT53755 40
30
20
10
A 0
0 1 3 5 10 30 50 100
pressure drop over electrical heater and T-REG in kPa
F2-F4 Process fluid circuit F1-F3 Cooling circuit
Design specification:
Heating mode:
– 6,9 or 12 kW heater
• Working condition: water at 140°C, 10 bar
• Heater only with a built-in type "J" Thermocouple
Cooling mode:
– Up to 70 kW cooling
• 20°C water inlet and 20 l/min
• 90°C water inlet and 45-50 l/min
Maximum working pressure:

16 bar on both circuit.
Heater code: YT57432, YT57433, YT57434
Channel plate measurement:
189 x 70 mm
B
Material specification:
BPHE parts in AISI 316 stainless steel:
• Channel plates, Start/End plates, Connections, Support plate
Frame in AISI 304 steel
Heater: Core pipe: AISI 304, Dissipator: aluminum
Port Available connections

Process fluid outlet ISO-G ½" A int
without cooling (P4)
Process fluid outlet ISO-G ½" A int
with cooling (F2)
Cooling water inlet (F1) ISO-G ½" A int
Cooling water outlet (F3) ISO-G ½" A int

Principle Process fluid inlet Air ventilation:

Possibility of draining unit from air by outlet on neck.
Pilot indentation for possible use.
Max number of plates:

Air ventilation 24 plates are used for all heater sizes 6, 9, 12 kW
possibilty Process fluid outlet
with cooling
Standard connection height:
20 mm
Cooling Water Inlet
Process fluid
outlet without
cooling
Cooling Water Outlet
www.swep.net www.htspa.it
PRODUCT SHEET
V10T
The V10T is our smallest evaporator. It delivers excellent heat transfer in
many cooling applications, and replaces traditional technologies such as
tube-in-tube and coaxial heat exchangers. The versatile V10T operates
efficiently with all modern refrigerants.
2.54+(0.265*NoP) lb
Standard dimensions
# MM IN
A 289 11.38
B 119 4.69
C 243 9.57
D 72 2.83
F 4.00+2.24*(NoP) 0.16+0.09*(NoP)
G 6 0.24
R 22 0.87
E_1 20.10 0.79
www.swep.net | Product No. 100000830, V10TH/1P-SC-S | This PDF was generated 2020.06.17
Threaded Connection Solder Connection Weld Connection Threaded Ultra High Combo Connection
Approved

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
V26
The V26 is based on the B26 high-performance condenser with our
AsyMatrix® technology. The V-ring refrigerant distribution system is
adapted for reversible air-to-water heat pumps and ensures optimal
performance as an evaporator in reversed mode. The distribution system
does not impact functionality or performance during condenser operation.
3.29+(0.244*NoP) lb
Standard dimensions
# MM IN
A 376 14.8
B 119 4.69
C 329 12.95
D 72 2.83
F 4.00+1.61*(NoP) 0.16+0.06*(NoP)
G 6 0.24
R 23 0.91
E_1 20.10 0.79
www.swep.net | Product No. 100000720, V26H/1P-SC-M | This PDF was generated 2020.06.17
Hose Connection Solder Connection Threaded Ultra High Threaded Connection Combo Connection Victaulic Connection Weld Connection
Approved

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
V25T
The versatile V25T delivers efficient heat exchange solutions across a
wide capacity interval, and is quick and simple to adapt for numerous
applications. The product’s versatility and excellent heat transfer make it
perfect for demanding cooling applications and as a reversible
condenser and cascade in two-phase applications. The V-ring refrigerant
distribution system ensures optimal performance as an evaporator in
both counter- and co-current configurations and with larger plate packs.
4.69+(0.457*NoP) lb
Standard dimensions
# MM IN
A 526 20.71
B 119 4.69
C 479 18.86
D 72 2.83
F 4.00+2.25*(NoP) 0.16+0.09*(NoP)
G 6 0.24
R 23 0.91
E_1 20.10 0.79
Solder Connection Threaded Connection Combo Connection Flange Connection Threaded Ultra High Victaulic Connection Weld Connection Hose Connection
Approved

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
V80
The V80 evaporator has been developed to perform effectively in a wide
range of applications. It operates at very wide capacity intervals, making
it the obvious choice for most types of evaporator applications.
4.61+(0.428*NoP) lb
Standard dimensions
# MM IN
A 526 20.71
B 119 4.69
C 470 18.5
D 63 2.48
F 4.00+2.24*(NoP) 0.16+0.09*(NoP)
G 6 0.24
R 23 0.91
E_1 27.10 1.07
Solder Connection Threaded Connection Threaded Ultra High Combo Connection Victaulic Connection Weld Connection
Approved

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
V35T
The V35T has been developed as both an ideal high-capacity
economizer for air-cooled chillers and a versatile evaporator for
circulating chillers with high temperature approaches. The various plate
types available make it easy to get a good thermal fit where other heat
exchanger technologies have traditionally offered a better solution. The
V35T is particularly suitable as an economizer for air conditioning and
marine refrigeration, and as an evaporator for manufacturing industries
such as plastic injection molding.
34.73+(0.564*NoP) lb
Standard dimensions
# MM IN
A 393 15.47
B 243 9.57
C 324 12.76
D 174 6.85
F 22.00+2.26*(NoP) 0.87+0.09*(NoP)
G 0 0
R 35 1.38
E_1 27.10 1.07
www.swep.net | Product No. 100000670, V35TH0/1P-SC-M | This PDF was generated 2020.06.17
Victaulic Connection Solder Connection Combo Connection Weld Connection Threaded Connection

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000670, V35TH0/1P-SC-M | This PDF was generated 2020.06.17
PRODUCT SHEET
V120T
The V120T is an evaporator that operates efficiently with many
refrigerants. It combines compact size and a specially developed plate
pattern in a highly efficient heat exchanger with a long thermal length. The
V120T is the perfect choice for chillers, heat pumps, and economizers.
Max flow 27.4 m³/h (120.64 gpm)
18.36+(0.935*NoP) lb
Standard dimensions
# MM IN
A 525 20.67
B 243 9.57
C 456 17.95
D 174 6.85
F 10.00+2.29*(NoP) 0.39+0.09*(NoP)
G 4 0.16
R 35 1.38
E_1 27.10 1.07
www.swep.net | Product No. 100000635, V120TH/1P-SC-M | This PDF was generated 2020.06.17
Solder Connection Combo Connection Threaded Connection Weld Connection Flange Connection Victaulic Connection

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
V200T
The V200T is an evaporator that operates efficiently with many
refrigerants. It combines compact size and a specially developed plate
pattern in a highly efficient heat exchanger with a long thermal length. The
V200T is the perfect choice for chillers, heat pumps, and economizers.
Max flow 43.7 m³/h (192.41 gpm)
20.84+(0.926*NoP) lb
Standard dimensions
# MM IN
A 525 20.67
B 243 9.57
C 448.50 17.66
D 163.50 6.44
F 10.00+2.29*(NoP) 0.39+0.09*(NoP)
G 4 0.16
H 450 17.72
I 171 6.73
J 4.50 0.18
K 42 1.65
N 37.50 1.48
R 35 1.38
E_1 54.20 2.13
Solder Connection Threaded Connection Combo Connection Weld Connection Victaulic Connection Flange Connection

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
V400T
The V400T functions extremely effectively at high capacities. Its
innovative design makes it an excellent choice for compact solutions in
demanding chiller applications.
34.02+(1.543*NoP) lb
Standard dimensions
# MM IN
A 694 27.32
B 304 11.97
C 601 23.66
D 205.50 8.09
F 18.00+2.29*(NoP) 0.71+0.09*(NoP)
G 0 0
H 597 23.5
I 215.50 8.48
J 3.50 0.14
K 52 2.05
N 47.50 1.87
O 2 0.08
R 44 1.73
V 150 5.91
E_1 54.10 2.13
Solder Connection Weld Connection Victaulic Connection Threaded Connection Flange Connection

3rd party Approvals

notice.

Disclaimer
PRODUCT SHEET
V65
The efficient and powerful V65 has been specially developed for
demanding high-capacity cooling applications, in particular advanced
chiller and gas vaporization applications.
Max flow 155.5 m³/h (684.65 gpm)
60.50+(2.359*NoP) lb
Standard dimensions
# MM IN
A 864 34.02
B 363 14.29
C 731 28.78
D 231 9.09
F 17.00+2.32*(NoP) 0.67+0.09*(NoP)
G 0.50 0.02
R 67 2.64
E_1 54.10 2.13
www.swep.net | Product No. 100000400, V65H/1P-SC-S | This PDF was generated 2020.06.17
Flange Connection Weld Connection Solder Connection Combo Connection Threaded Connection Victaulic Connection

3rd party Approvals

notice.

Disclaimer
www.swep.net | Product No. 100000400, V65H/1P-SC-S | This PDF was generated 2020.06.17

Industrial Heat Transfer Solutions EN1

Uploaded by

Copyright:

Available Formats

Industrial Heat Transfer Solutions EN1

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Industrial Heat Transfer Solutions EN1

Uploaded by

Copyright:

Available Formats

INDUSTRIAL

Simple, flexible, cost-effective BPHEs, counter-current flow is more common

In a one-pass configuration, the two flows are Easy to install

• Tailored: Optimized and customized

• Performance: Reliable, energy-efficient and cost-effective

• Economical: Optimal material usage

• Versatile: Cover a wide range of cooling and heating

• Competitive: Save space compared with S&T heat

• Turbulent: Resist scaling and fouling; effective self-

• Innovative: Patented solutions, e.g. true dual, double-wall

• Tested: Pressure- and leak-tested. All widely recognized

• Responsive: Small holdup volume and lower refrigerant

• Standards: Comply with standards such as ISO 9001

High-quality products and services

Largest production capacity in the world

Assured longest service life

Top performance you can trust

Application and product knowledge

Air dryers for air compressors

We use Statistical Process Control (SPC) through- Pressing

Design specification (ISO class 5)

Refrigerant side: R134a, Tevap = 0°C, SH = 5K

Max working pressure

PP formula: 3+[2.17x(NoP A-1)+2.24x(NoP B-1)]+37 or 52

Model Flow rate NoP NoP Refrigerant hold-up Total PP

pressure drop (kPa)

ADWIS 50 35 - 50 10 17 0,088 95,4 40

ADWIS 100 115 - 150 20 37 0,198 176,9

Air to air package

Dry air out

Design specification (ISO class 5)

Tin = 95°F, Tout = 80.6°F

Refrigerant side: R134a, Tevap = 32°F, SH = 9°F

Max working pressure

PP formula: 0.118+[0.085x(NoP A-1)+0.088x(NoP B-1)]+1.456 or 2.047

Model Flow rate NoP NoP Refrigerant hold-up Total PP 8

pressure drop (psi)

ADWIS 50 20 - 30 10 17 0.003 3.8 5 ADWIS 35

ADWIS 100 70 - 90 20 37 0.007 7.0

Air to air package

Dry air out

Design specification (ISO class 5)

Tin = 35°C, Tout = 27°C

Max working pressure

18489-* Solder 42U Solder 12,8 ¾” INT

ADWIS 150 150 - 200 14 17 0,378​ 148,5 0

0 100 200 300 400 500

Flow rate in accordance with ISO 7183 - 20°C and 0 bar(g)

Air to air package

Dry air out

Design specification (ISO class 5)

Air side: P = 102 psi(g), Tdew = 44.6°F, ∆P = 5.8 psi,

Tin = 95°F, Tout = 80.6°F

Max working pressure

18489-* Solder 42U Solder 12,8 ¾” INT

ADWIS 150 90 - 120 14 17 0.013 5.8 0

0 50 100 150 200 250

Flow rate in accordance with ISO 7183 - 20°C and 0 bar(g)

Air to air package

Dry air out

ADWIS 150 150 - 200 14 17 0,378 148,5 0