E-Flo iQ ®

Single Component Metering and Dispensing System for Urethane

A new level of intelligence, control & performance

• Low cost of ownership

• Consistent control and accurate performance
• Simple system design and easy to integrate

PROVEN QUALITY. LEADING TECHNOLOGY.

A new level of intelligence, control & performance
The E-Flo iQ is a single component tank-to-tip solution that provides your automatic
applications with an intelligent metering system. With its electric servo-driven motor,
the E-Flo iQ will meter directly from the drum and keeps an optimal and continuous flow
control with assured performance without the need of external metering systems.

Lower your cost of ownership

Metering directly from the drum reduces the number of system Realize increased uptime at installation
components and lets you eliminate external metering systems all • Easy installations: You will start realizing the increased
together. With the simple setup of electric servo-driven pump, hose uptime of the installation. With the simplicity of E-Flo iQ,
and valve, you will realize an immediate impact to your total cost of installations are done quickly and with ease.
ownership.
• Low maintenance: By using parts that have been proven in
industries to be long lasting and of high quality, maintenance
Lower sound levels needs are extremely low. Also with the easy to access and
With current delivery systems, the sound levels often go well program diagnostics screens, you will be able to analyze
above 80 dBa. Because the E-Flo iQ is using an electric servo- the total work of the pump and determine preventive
driven motor, the sound level is often less then 70 dBa, making maintenance.
your working environment quieter.
• Continuous dispensing without reloading
Lower payloads for your robot
With only a hose and valve mounted on the robot you are able Applications
to select a smaller, less expensive robot with a smaller payload Glass bonding for automotive, agriculture,transportation and other
capacity. heavy equipment.
• Windshield • Sun Roofs
• Back Glass • Cabin Glass
• Quarter Glass • Cabin Roofs
Increase your overall equipment effectiveness

Consistent control of the flow rate with assured performance

Having accurate dispensing from start to finish and during the complete dispensing is not an easy task. You have to be able to control the
flow and pressure, take into consideration the speed of the robot and be able to handle a wide range of materials for heated applications.

Controlling and dispensing at accurate flow rates

The core of Meter from Drum Technology™ is the electric
servo-driven motor. It is always aware of the position of the
piston pump and its velocity, thus allowing the flow rate to be
controlled and maintained at all times. Pressure sensors are
placed at key locations to monitor and make sure the pressure
is consistent from tank to tip.

Precise and Accurate Rotating Dispense Valve

The Graco Axial Dispense Valve is a lightweight, high flow, high
pressure applicator designed for precision robotic application of
urethanes. Designed with swivel functionality, the valve can rotate
independently of the cables and hoses to prevent stress on the
robot and the hoses for precise and consistent bead application.

3
 An easy to use control module with simple integration options

An easy to use control module

With the Advanced Display Module (ADM) on the E-Flo

iQ, setting up and programming a metering system has
never been easier.

It’s intuitive screens make setting up of a bead profile

quick and easy and lets you save up to 16 different
dispense styles.

Simple diagnostics

The ADM also incorporates simple diagnostic

screens which allow you to quickly check all the
process variables and define predictive maintenance
parameters.

Integration with the PLC

The communication gateway module (CGM) has

integrated mapping of all of the programming data.
Simply connect the CGM to the PLC for complete
integration. Currently available protocols include
EtherNet I/P, PROFINET, DeviceNet, or PROFIBUS.

By using the CGM you will be able to program an

unlimited number of dispensing styles.

4
Proven components

Electric servo-driven motor

A quiet electric motor that accurately

controls the system flow rate.
Heating

The system will have a heat

control module to handle Display module
adhesives up to 158°F (70°C).
Next to the pump and platen Intuitive, easy-to-use screen
heat zones, there are 6 heat navigation provides simple setup,
zones for single systems and monitoring and diagnostics.
12 for tandem systems.

Communication
gateway module Platen design
The communication gateway
module allows complete Minimizes leftover material and
integration over EtherNet/ reduces waste. Long-lasting,
IP, PROFINET, PROFIBUS, and one-piece platen seals are easy
DeviceNet or simple integration to replace.
over discrete I/O.

Hoses Axial Rotating Dispense Valve

Graco hoses maintain the material Designed for the robotic application of
temperature and improve material urethane sealants for glass bonding.
integrity. For heated systems, the hoses
are insulated for an accurate and
uniform material temperature.

5
 Technical information

E-Flo iQ Metering and Dispensing System

US Metric
Maximum fluid operating temperature 158°F 70°C
Maximum working pressure 4000 psi 28 MPa, 276 bar
Maximum driver cycle rate 25 cycles per minute
Air inlet size (supply system) 3/4 npt (f)
Ambient operating temperature range (supply system) 32-120°F 0-49°C

Flow rate 10 cc/min - 2000 cc/ min

(max. flow rate is based on Urethane viscosities dispense through the Axial Valve)
Gateway EtherNet/IP, DeviceNet, PROFINET, PROFIBUS

Electrical requirements
Ambient system electrical ratings 200-240 VAC, 1 phase, 50/60 Hz, 20 A
200-240 VAC, 1 phase, 50/60 Hz, 20 A
Heated system electrical ratings 200-240 VAC, 3 phase (Δ), 50/60 Hz, 38 A
380-420 VAC, 3 phase (Y), 50/60 Hz, 38 A

Fluid outlet size

Check-Mate 200 1" npt (f)

Maximum air input pressure (supply system)

D200s - 6.5 in. dual post, 200 L (55 gal.) 125 psi 9 bar, 0.9 MPa

Axial Rotating Dispense Valve

US Metric
Maximum fluid working pressure 4000 psi 276 bar, 28 MPa
Maximum cylinder air pressure 120 psi 8.0 bar, 0.8 MPa
Maximum fluid operating temperature 158°F 70°C

Inlet/Outlet Sizes
Air inlet size 1/8 in. npt(f) (Remote solenoid options only)
Air exhaust port size 1/8 in. npt (f)
Fluid inlet size 1/4 in. npt (f)

Weight
Weight: 10.6 lb (4.8 kg)

6
Ordering information

Selection of the E-Flo iQ system for Urethane

The E-Flo iQ System provides the flexibility to configure a system to meet your specific needs. This includes offering
multiple combinations of supply systems, Axial dispensing valves, hoses and accessories.

Material Container Material

Part Number Configuration Pump RAM Hoses
Volume (gal) Container

Check-Mate
26B545 Single D200s 55 200 10 ft hose
200cc

Check-Mate
26B546 Single D200s 55 200 15 ft hose
200cc

Check-Mate
26B547 Single D200s 55 200 20 ft hose
200cc

Check-Mate 10 ft hose,
26B548 Single D200s 55 200
200cc 10 ft hose (WIP)

Check-Mate 15 ft hose,
26B549 Single D200s 55 200
200cc 10 ft hose (WIP)

Check-Mate 20 ft hose,
26B550 Single D200s 55 200
200cc 10 ft hose (WIP)

Check-Mate 15 ft hose,
26B551 Single D200s 55 200
200cc 15 ft hose (WIP)

Check-Mate 20 ft hose,
26B552 Tandem D200s 55 200
200cc 15 ft hose (WIP)

Check-Mate 20 ft hose,
26B553 Tandem D200s 55 200
200cc 20 ft hose (WIP)

Check-Mate Two 10 ft hoses,

26B554 Tandem D200s 55 200
200cc 10 ft hose (WIP)

Check-Mate Two 10 ft hoses,

26B555 Tandem D200s 55 200
200cc 15 ft hose (WIP)

Check-Mate Two 10 ft hoses,

26B556 Tandem D200s 55 200
200cc 20 ft hose (WIP)

Check-Mate Two 15 ft hoses,

26B557 Tandem D200s 55 200
200cc 10 ft hose (WIP)

Check-Mate Two 20 ft hoses,

26B558 Tandem D200s 55 200
200cc 10 ft hose (WIP)

Check-Mate Two 20 ft hoses,

26B559 Tandem D200s 55 200
200cc 15 ft hose (WIP)

Check-Mate Two 20 ft hoses,

26B560 Tandem D200s 55 200
200cc 20 ft hose (WIP)

7
 ABOUT GRACO Founded in 1926, Graco is a world leader in fluid handling systems and components. Graco products
move, measure, control, dispense and apply a wide range of fluids and viscous materials used
in vehicle lubrication, commercial and industrial settings.

The company’s success is based on its unwavering commitment to technical excellence, world-class
manufacturing and unparalleled customer service. Working closely with qualified distributors, Graco
offers systems, products and technology that set the quality standard in a wide range of fluid handling
solutions. Graco provides equipment for spray finishing, protective coating, paint circulation, lubrication,
and dispensing sealants and adhesives, along with power application equipment for the contractor
industry. Graco’s ongoing investment in fluid management and control will continue to provide
innovative solutions to a diverse global market.

GRACO LOCATIONS MAILING ADDRESS ASIA PACIFIC INDIA

P.O. Box 1441 Graco India Pvt Ltd.
Minneapolis, MN 55440-1441 AUSTRALIA Plot No 295, Udyog Vihar Phase-IV
Tel: 612-623-6000 Graco Australia Pty Ltd. Guragram, Haryana
Fax: 612-623-6777 Suite 17, 2 Enterprise Drive India 122015
Bundoora, Victoria 3083 Tel: 91 124 6610200
Australia Fax: 91 124 6610201
Tel: 61 3 9468 8500
AMERICAS Fax: 61 3 9468 8599
MINNESOTA
Worldwide Headquarters
Graco Inc. CHINA JAPAN
88 -11th Avenue N.E. Graco Fluid Equipment Graco K.K.
Minneapolis, MN 55413 (Shanghai) CO., LTD 1-27-12 Hayabuchi
Building 7, No. 1-2, Wenshui Tsuzuki-ku
Road 299, Jing’an District, Yokohama City, Japan 2240025
Shanghai 200436 Tel: 81 45 593 7300
EUROPE The People’s Republic of China Fax: 81 45 593 7301
BELGIUM Tel: 86 21 6495 0088
European Distribution Center Fax: 86 21 6495 0077 KOREA
Graco Distribution BV Graco Korea Inc.
Industrieterrein-Oude Bunders 38, Samsung 1-ro 1-gil
Slakweidestraat 31 Hwaseong-si, Gyeonggi-do, 18449
3630 Maasmechelen, Republic of Korea
Belgium Tel: 82 31 8015 0961
Tel: 32 89 770 700 Fax: 82 31 613 9801
Fax: 32 89 770 777

SALES/ Call today for product information or to request a demonstration.

DISTRIBUTION/
SERVICE
800-746-1334 or visit us at www.graco.com.
Graco Inc. is registered to I.S. EN ISO 9001

©2021 Graco Inc. 350447 Rev. A 06/21 All written and visual data contained in this document are based on the latest
product information available at the time of publication. Graco reserves the right to make changes at any time without notice.
All other brand names or marks are used for identification purposes and are trademarks of their respective owners.