Scribd
Upload
19 views2 pages

Router

The document configures subinterfaces and IP addresses on a router interface, enables EIGRP routing with auto-summary disabled, and adds networks to EIGRP routing process 20.

Uploaded by

luis.bascunan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
19 views2 pages

Router

The document configures subinterfaces and IP addresses on a router interface, enables EIGRP routing with auto-summary disabled, and adds networks to EIGRP routing process 20.

Uploaded by

luis.bascunan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

Router>ena

Router>enable
Router#conf
Router#configure t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int
Router(config)#interface gi
Router(config)#interface gigabitEthernet 0/1.2
Router(config-subif)#enc
Router(config-subif)#encapsulation dot
Router(config-subif)#encapsulation dot1Q 2
Router(config-subif)#ip add
Router(config-subif)#ip address 192.168.2.1 255.255.255.192
Router(config-subif)#exit
Router(config)#int
Router(config)#interface gi
Router(config)#interface gigabitEthernet 0/1.3
Router(config-subif)#enc
Router(config-subif)#encapsulation dot
Router(config-subif)#encapsulation dot1Q 3
Router(config-subif)#ip add
Router(config-subif)#ip address 192 168.3.1 255.255.255.240
^
% Invalid input detected at '^' marker.
Router(config-subif)#ip add
Router(config-subif)#ip address 192.168.3.1 255.255.255.240
Router(config-subif)#exit
Router(config)#int
Router(config)#interface gi
Router(config)#interface gigabitEthernet 0/1
Router(config-if)#no sh
Router(config-if)#no shutdown

Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state


to up
Router>ena
Router>enable conf
Router>enable
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#ro
Router(config)#router ig
Router(config)#router ig
Router(config)#router ei
Router(config)#router eigrp 20
Router(config-router)#no au
Router(config-router)#no auto-summary
Router(config-router)#net
Router(config-router)#network 50.50.50.0
Router(config-router)#eig
Router(config-router)#eigrp 20
^
% Invalid input detected at '^' marker.
Router(config-router)#exit
Router(config)#}rou
Router(config)#}rou
Router(config)#}rouro
Router(config)#}ro
Router(config)#}router ei
Router(config)#}router eigrp 20
^
% Invalid input detected at '^' marker.
Router(config)#ro
Router(config)#router ei
Router(config)#router eigrp 20
Router(config-router)#no au
Router(config-router)#no auto-summary
Router(config-router)#net
Router(config-router)#network 192.168.3.0 0.0.0.63
Router(config-router)#exit
Router(config)#rou
Router(config)#router ei
Router(config)#router eigrp 20
Router(config-router)#no a
Router(config-router)#no auto-summary
Router(config-router)#net
Router(config-router)#network 192.168.2.0 0.0.0.15
Router(config-router)#

You might also like