HOW TO SELECT A

PELTIER MODULE
By: Bruce Rose, CUI Devices
www.cuidevices.com

How to Select a Peltier Module

Common thermal management solutions used in electronics applications address

cooling objects with heat exchangers and fluid flow. The heat exchanger is typically
either the electronic package itself or an extruded or stamped heat sink attached
to the package. Air is the most common fluid used in thermal solutions, either with
natural convection or propelled by a fan. In most of these solutions the temperature
of the object being cooled remains above the ambient temperature. Peltier modules
are electronic devices designed for cooling objects to below the ambient temperature
or maintaining objects at a specific temperature by controlled heating or cooling.
Selecting or specifying a Peltier module is not difficult but a basic understanding of
module characteristics can be helpful to ensure the process flows smoothly.

THE THERMAL PROBLEM TO BE SOLVED

Many electronic components provide an improved signal to noise ratio at cooler
temperatures or are susceptible to damage when operating at temperatures exceeding
specifications. Similarly, some chemical reactions must be maintained at or below a specific
temperature. In these applications a Peltier module can be used to solve thermal issues
and cool objects to below the ambient temperature where a conventional heat sink and
fan cannot do so. Additionally, Peltier modules and the appropriate control circuit enable
the ability to maintain an object at a specific temperature even under rapidly fluctuating
thermal loads.

PELTIER MODULE BASICS

Peltier modules contain two external ceramic plates separated by semiconductor pellets.
One of the plates absorbs heat (becomes cooler) and the other plate dissipates heat
(becomes hotter) when a current is passed through the semiconductor pellets. More
details regarding the construction and operation of Peltier modules can be found in this
technical paper.

The following constraints should be understood when selecting or specifying a Peltier

module, which we will cover in the following sections:

1. Heat transfer through the module

2. Temperature difference across the module

3. Temperature of hot side of the module

4. Surface area of module

5. Required operating current

6. Required driving voltage

Page 2
www.cuidevices.com

How to Select a Peltier Module

Figure 1:
Diagram of a basic
Peltier module
structure

HEAT TRANSFER THROUGH PELTIER MODULES

The amount of heat to be transferred through a Peltier module from the cold side to the
hot side is denoted Q and is specified in Watts. This parameter may be the heat generated
by an object to be cooled or it may be the heat conducted to the ambient environment
from the object being cooled. It should be understood that Peltier modules do not possess
the ability to absorb thermal energy. Peltier modules only transfer thermal energy and the
energy being transferred will need to be dissipated on the hot side of the module.

Figure 2:
Model showing heat
flow from the cold to
hot side of a module

Page 3
www.cuidevices.com

How to Select a Peltier Module

TEMPERATURE DIFFERENCE ACROSS PELTIER MODULES

The temperature difference specified in a Peltier module datasheet (ΔT) is measured

on the outside surfaces of the two ceramic plates of the module. Care must be taken
to understand if there is any temperature difference between the Peltier module plates
and the external system temperatures of interest. The following diagram indicates five
potentially different temperature regions of a Peltier module system.

Figure 3:
Diagram showing
the various
temperature regions
of Peltier modules

TEMPERATURE OF THE HOT SIDE OF PELTIER MODULES

The characteristics of Peltier modules also change with operating temperature. Some
vendors, such as CUI Devices, provide specification data for more than one operating
temperature. Specification data will probably not be available for the specific operating
temperatures of the application and thus the closest available data should be used.

Page 4
www.cuidevices.com

How to Select a Peltier Module

SURFACE AREA OF PELTIER MODULES

The surface area of Peltier modules is typically specified based upon either the area of the
object to be cooled or the area available for heat dissipation. An area mismatch between
the area available and the area of the Peltier module can be compensated for by the use of
a low thermal impedance heat spreader. A simple heat spreader can be manufactured from
aluminum or copper.

Figure 4:
Diagram showing
the various
temperature regions
of Peltier modules

REQUIRED OPERATING CURRENT

Peltier modules are current-driven devices similar to LEDs. The desired operating
parameters are most conveniently achieved by driving the module with a controlled current
source and allowing the current source to provide the required load voltage (the voltage
compliance of the current source). This is analogous to providing a specific voltage to a
voltage driven device and then letting the voltage source provide the required current (i.e.
providing a voltage to a microprocessor and ensuring the voltage source can provide the
required load current).

Peltier modules can be driven with voltage sources but doing so will make it more difficult
to accurately control the heat flow and temperature difference across the module.

REQUIRED OPERATING VOLTAGE

The required voltage compliance of the current source will be determined from the Peltier
module datasheet and operating constraints.

Page 5
www.cuidevices.com

How to Select a Peltier Module

AN EXAMPLE OF SPECIFYING THE PROPER PELTIER

MODULE
The following example demonstrates the process of selecting or specifying a Peltier
module for an application. In this example we will be using the CP603315H Peltier module.

CONDITIONS

● Heat transfer through the module: 20 W

● Temperature difference across the module: 20°C

● Temperature of hot side of module: 30°C (use 27°C graphs)

● Surface area of object: 30 x 30 mm

1. Draw horizontal line at 20 W on lower vertical axis which represents the power
transferred through the Peltier module.

2. Draw vertical line at 20°C on lower horizontal axis which represents the temperature
difference maintained across the Peltier module.

3. Operating current of 2.7 A is interpolated from where horizontal line (1) and vertical
line (2) intersect. This is the current required to operate the Peltier module.

Page 6
www.cuidevices.com

How to Select a Peltier Module

4. In the upper half of the graph mark where vertical line (2) intersects 2.7 A.

5. Operating voltage of 7.5 V is interpolated from drawing a horizontal line from the
intersection in step 4 to the upper vertical axis. This is the required voltage compliance
of the current source.

EXAMPLE SUMMARY

● Peltier module selected: CP603315H

● Heat transferred through Peltier module: Q = 20 W

● Temperature maintained across Peltier module: ΔT = 20°C

● Temperature of Peltier module hot side: Th = 30°C

● Current source required to power Peltier module: I = 2.7 A

● Required Voltage compliance of current source: V = 7.5 V

● Power dissipated in heat sink in addition to that transferred through Peltier module: P
= 20 W

● Total heat to be dissipated by heat sink: 40 W; 20 W heat transferred plus 20 W

electrical power

CONCLUSION
Peltier modules can be an optimum solution when there is a need to cool an object to
below the ambient temperature or to maintain an object at a specific temperature. To
ensure a successful design it is important to select a vendor with multiple choices of Peltier
modules and adequate characterization data. In addition to partnering with a reliable
vendor it is also critical to understand the subtle details regarding module implementation
and operation such as the basics outlined in this post.

View CUI Devices’ full line of Peltier modules

LEARN MORE

Page 7 © 2019 CUI Devices. All rights reserved. 10/2019