4 Gpon FTTH Iptv Service Provisioning v8r13 Issue1.10 (S+N)

GPON FTTH IPTV
Service Provisioning
www.huawei.com
Copyright © Huawei Technologies Co., Ltd. All rights reserved.

Objectives
⚫ Upon completion of this course, you will be able to :
 Describe GPON FTTH IPTV solution networking , multicast
specification and basic principle
 Master how to do the GPON FTTH IPTV service configuration
 Know the basic steps to check the GPON IPTV service
Copyright © Huawei Technologies Co., Ltd. All rights reserved. Page1

Contents
1. GPON IPTV Service Implementation Principle
2. GPON IPTV Service Configuration Basics
3. GPON IPTV Service Configuration Example
4. GPON IPTV Service Maintenance

Huawei IPTV Solution Networking
Background
Support Layer BSS
OSS
Operation
Middleware
Management
Layer (Back office)
VOD
Central
NMS
Headend CA System VOD EPG

System BTV Distribution Distribution
Service
Network Layer VOD
IP Network
VOD Server
Server
BTV VOD EPG
EPG AN
EPG
Terminal Layer HOME GATEWAY

CPE
TV+STB TV+STB

GPON IPTV Service Procedure
OSS/BSS
Video service
Step 4 video SMS send the management system
Step5 video stream
channel authorized message
forward to the OLT in
to PON-OLT
IP multicast mode
Step3 PON-OLT forward the multicast

stream,IGMP Proxy,CA functions：
Session 1 PON-OLT authenticate the user
whether allowed to watch the channel
according the user right BRAS
Session 2 forward the multicast stream
through the multicast VLAN after
authentication with the guaranteed QoS
PON-OLT
Step2 terminal send

IGMP Join/Leave message
to change the channel
Home
ONU Network ONU
Step1 STB or PC terminal get STB
IP address from BRAS via
PPPOE/ DHCP, and download PC
EPG from the EPG server TV PC

GPON IPTV VLAN Architecture
OLT
IGMP
OLT can isolate Multicast and unicast
Process
ONT service even they use the same C-
VLAN8
STB VLAN in the user side
M-VLAN
…
ONT
VLAN8 U-VLAN
STB
OLT M-VLAN IPTV
STB ONT VLAN8

M-VLAN
…
U-VLAN VoD
STB ONT VLAN8 U-VLAN

Router
Unicast VLAN Multicast

Uplink Port Multicast Video U-VLAN for VOD or M-VLAN VLAN for
GPON Port IGMP message
Stream EPG multicast
video

Multicast Specification
 The system supports up to 256 multicast VLANs. Each multicast VLAN
◼ can work in proxy or snooping mode.
◼ support IGMP V2 or IGMP V3.
◼ support up to 8192 users.
◼ support difference program creation modes: static and dynamic.
◼ The multicast upstream port can be specified for each multicast VLAN.
 System supports up to 4096 programs, including 2000 concurrently online

programs.
 Each GEM port on the GPBC service board supports one multicast user.
 A multicast user can watch up to 32 programs concurrently.

Questions
⚫ What’s the function of unicast VLAN and multicast VLAN?
⚫ How many programs does a multicast user can watch

concurrently?
 A.4000 B. 256 C.32
⚫ What are the two IGMP modes?

Contents

Flow Chart-Add ONT
Start
Y N
ONU added?
Create DBA profile
Modify ont-lineprofile Add ONU procedure
Modify ont-srvprofile
Set ONU port native VLAN (Optional)
IPTV service

Flow Chart- IPTV Service
Provision GPON basic service
Provision VLAN
Provision IGMP user
Provision IGMP
Provision multicast VLAN
Provision multicast VLAN uplink
Disable (Dynamic)
Provision multicast
Program match
VLAN mode
Enable (Static)
Add programs
Provision IGMP mode and version
Provision multicast VLAN member

Add IGMP User
⚫ Add igmp user
◼ OLT(config)#btv
◼ OLT(config-btv)#igmp user add
– { port<K>|service-port<K>|slot<K>|smart-vlan<K> }:service-port
– { index<0,32767> }:10
– { <cr>|auth<K>|globalleave<K>|igmp-version<K>|log<K>|max-
bandwidth<K>|max-program<K>|no-auth<K>|
– quickleave<K>|video<K> }:auth

Add IGMP User (Cont.)
– { <cr>|globalleave<K>|igmp-version<K>|log<K>|max-
bandwidth<K>|max-program<K>|quickleave<K> |video<K>}:max-
program
– { max-program-num<1,32>|no-limit<K> }:8
– { <cr>|globalleave<K>|igmp-version<K>|log<K>|max-
bandwidth<K>|quickleave<K>|video<K> }:
//Before you add a multicast user, the service port of this user must be
existing. You can run the display service-port command to query the
information about a service port.

Multicast VLAN Uplink Port
⚫ Create multicast vlan and log into multicast vlan mode
◼ OLT(config)#multicast-vlan 5
◼ OLT(config-mvlan5)#
⚫ Set igmp uplink port in multicast vlan mode

◼ OLT(config-mvlan5)#igmp uplink-port 0/19/0
//Specify an upstream port for sending and receiving multicast packets,

including protocol and data packets

IGMP Program Match Mode
⚫ Set igmp program match mode
◼ OLT(config-mvlan5)#igmp match mode enable
When the match mode is set as enable, multicast programs need to be

pre-configured.
When the match mode is set as disable, multicast programs need not to
be pre-configured and are automatically generated according to the
users' demanding.

Add IGMP Program
⚫ Add IGMP programs
◼ OLT(config-mvlan5)#igmp program add
– { batch<K>|ip<K>|ipv6<K>|name<K> }:name
– { name<S><Length 1-16> }:program1
– { ip<K>|ipv6<K>}:ip
– { ip-addr<X.X.X.X> }:224.1.1.1
– { <cr>|bandwidth<K>|grade<K>|host<K>|hostip<K>|index
<K>|log<K>|prejoin<K>|preview-profile<K>|priority<K>
|sourceip<K>|unsolicited<K> }:

Batch Add IGMP Program
⚫ Batch Add IGMP programs
◼ OLT(config-mvlan5)#igmp program add
– { batch<K>|ip<K>|ipv6<K>|name<K> }:batch
– { ip<K>|ipv6<K>}:ip
– { ip-addr<X.X.X.X> }:224.1.1.2
– { to-ip<K> }:to-ip
– { ip-addr<X.X.X.X> }:224.1.1.10
– { <cr>|bandwidth<K>|hostip<K>|preview-
profile<K>|priority<K>|sourceip<K>}:

Add IGMP Right Profile
⚫ Add IGMP right profile
◼ OLT(config-btv)#igmp profile add profile-name profile0
◼ OLT(config-btv)#igmp profile
– { add<K>|delete<K>|profile-index<K>|profile-
name<K>|rename<K> }:profile-name
– { profile-name<S><Length 1-16> }: profile0
– { program-list<K>|program-name<K>|vlan<K> }:program-name
– { program-name<S><Length 1-16> }:program1
– { forbidden<K>|idle<K>|preview<K>|watch<K> }:watch
◼ OLT(config-btv)#igmp user bind-profile service-port 10 profile-name profile0

Set IGMP Version and Mode
⚫ Set IGMP Version and Mode
◼ OLT(config-mvlan5)#igmp version
– { v2<K>|v3<K> }:v3
◼ OLT(config-mvlan5)#igmp mode
– { off<K>|proxy<K>|snooping<K> }:proxy
– Command:
igmp mode proxy
– Are you sure to change IGMP mode?(y/n)[n]:y

Multicast-VLAN Member
⚫ Add igmp user to multicast vlan
 OLT(config-mvlan5)#igmp multicast-vlan member service-
port 10
//A multicast user can watch the programs in a multicast VLAN only
after it is added to the multicast VLAN

Quick Add Multicast-VLAN Member
⚫ Example
◼ OLT(config-mvlan5)#igmp multicast-vlan quick member service-
port 10
To pre-configure the multicast subscriber to simplify the configuration of

the multicast subscriber, run igmp multicast-vlan quick member.
When a member is added to the MVLAN, the member is added as the
multicast subscriber even if the subscriber does not exist. If the
subscriber exists, this command functions the same as the command for
adding a member to the MVLAN.

Questions
⚫ Why do we need to add igmp user to multicast vlan?
⚫ What’s the difference between igmp match mode enable and

igmp match mode disable ?

Contents

Contents
3.1 Single VLAN Mode
3.2 Separated VLAN Mode

GPON FTTH Case BB service platform
TL1/CORBA IPTV Server
/API Notification
PC ETH
HG8245 Carrier’s OSS
NMS
HDTV ETH
OLT
Internet
Phone Ethernet
POTS ONT IP Core
BNG
Splitter
ONT HG8245: OLT
Softswitch
ETH port 4, POTS port 2
AAA Server
SN: 48575443BF656E04
Video Server
ONT ID:2
Server IP:192.168.46.240
ONT line profile：20
Program IP: 224.1.1.1- 224.1.1.10
ONT service profile：30
Type ONU C-VLAN GEM DBA TCONT Traffic S-VLAN OLT port
Port table
41: GPON: 0/2/0

IPTV ETH2 200 3 11 5 200
20M/40M Uplink: 0/19/0

Configure Procedure (1/3)
In this case the ONU is already added
⚫ Configure DBA profile
◼ OLT(config)#dba-profile add profile-id 11 type2 assure 2048
⚫ Modify ONT line profile

◼ OLT(config)# ont-lineprofile gpon profile-id 20
◼ OLT(config-gpon-lineprofile-20)#tcont 5 dba-profile-id 11
◼ OLT(config-gpon-lineprofile-20)#gem add 3 eth tcont 5
◼ OLT(config-gpon-lineprofile-20)#gem mapping 3 3 vlan 200
◼ OLT(config-gpon-lineprofile-20)#commit
⚫ Modify ONT service profile

◼ OLT(config)#ont-srvprofile gpon profile-id 30
◼ OLT(config-gpon-srvprofile-30)#ont-port eth 4 pots 2
◼ OLT(config-gpon-srvprofile-30)#port vlan eth 2 200 OLT(config-gpon-
srvprofile-30)#commit

ONT Register-Query Ont Serial Number
⚫ Enable ont autofind function
◼ OLT(config-if-gpon-0/3)#port 0 ont-auto-find enable
⚫ Query ont serial number

◼ OLT(config-if-gpon-0/3)#display ont autofind
{ portid<0,7> }:0
Command:
display ont autofind 0
-------------------------------------------------
Number : 3
F/S/P : 0/3/0
Ont SN : 48575443BF656E04
Password : 0x00000000000000000000
Loid :
Checkcode :
VendorID : HWTC
Ont Version : 130C4400
Ont SoftwareVersion : V1R002C00S203
Ont EquipmentID : 245
Ont autofind time : 2010-09-18 11:13:35+08:00
---------------------------------------------------

ONT Register-Add/Confirm ONT
⚫ confirm ONT
 OLT(config-if-gpon-0/3)#ont confirm
{ portid<0,7> }:0
{ all<K>|loid-auth<K>|ontid<K>|password-auth<K>|sn-auth<K>
}:ontid
{ ontid<0,127> }:2
{ loid-auth<K>|password-auth<K>|sn-auth<K> }:sn-auth
{ sn<S><Length 13-16> }:48575443BF656E04
{ omci<K>|password-auth<K>|snmp<K> }:omci
{ <cr>|desc<K>|ont-lineprofile-id<K>|ont-lineprofile-
name<K>|ont-srvprofile-id<K>|ont-srvprofile-name<K> }:ont-
lineprofile-id 20
{ <cr>|desc<K>|ont-srvprofile-id<K>|ont-srvprofile-name<K>
}:ont-srvprofile-id 30
{ <cr>|desc<K> }:

⚫ Configure ONT native VLAN (Optional)
◼ OLT(config)# interface gpon 0/3
◼ OLT(config-if-gpon-0/3)#ont port native-vlan 0 2 eth 2 vlan 200
⚫ Configure traffic table

◼ OLT(config)#traffic table ip index 41 cir 20480 pir 40960 cbs 20480 pbs
40960 priority user-cos 5 priority-policy local-Setting
⚫ Provision VLAN
◼ OLT(config)#vlan 200 smart
◼ OLT(config)#port vlan 200 0/19 0
◼ OLT(config)#service-port 2 vlan 200 gpon 0/3/0 ont 2 gemport 3 multi-
service user-vlan 200 rx-cttr 41 tx-cttr 41

⚫ Configure the IGMP and multicast VLAN Service port index
◼ OLT(config)#btv
◼ OLT(config-bTV)#igmp user add service-port 2 no-auth
◼ OLT(config)#multicast-vlan 200
◼ OLT(config-mvlan200)#igmp version v3
◼ OLT(config-mvlan200)#igmp match mode enable
◼ OLT(config-mvlan200)#igmp program add batch ip 224.1.1.1 to-ip
224.1.1.10
◼ OLT(config-mvlan200)#igmp mode proxy
◼ OLT(config-mvlan200)#igmp multicast-vlan member service-port 2
Service port index

Query the Program
⚫ Query the program
⚫ OLT(config)#display igmp program all
◼ ------------------------------------------------------------------------------
◼ Index| Create | IP | Program |User |VLAN |Prejoin|Priority
◼ | flag | address | name |num | ID | |
◼ ------------------------------------------------------------------------------
◼ 0 S 224.1.1.1 PROGRAM-0 0 200 disable 7
◼ ------------------------------------------------------------------------------
Query the IGMP User
⚫ Query the IGMP user
 OLT(config)#display igmp user all
------------------------------------------------------------------------------
User port Bind State Auth Quick IGMP Video Log Available
profiles leave flow ID flow ID switch programs
------------------------------------------------------------------------------
0/3/0/2 - online no-auth MAC-based 2 2 enable 8
------------------------------------------------------------------------------

Contents
3.1 Single VLAN Mode
3.2 Separated VLAN Mode

GPON FTTH Case BB service platform
TL1/CORBA IPTV Server
PC ETH /API Notification
HG8245 Carrier’s OSS
NMS
ETH
HDTV
OLT
Internet
Phone ONT Ethernet
POTS IP Core
Splitter BNG
ONT HG8245: OLT
ETH port 4, POTS port 2 Softswitch
AAA Server
SN:48575443BF656E04
Video Server
ONT ID:2
Server IP:192.168.46.240
ONT line profile：20
Program IP: 224.1.1.1- 224.1.1.10
ONT service profile：30
ONU C- S- M-
Type GEM DBA TCONT Traffic table OLT port
Port VLAN VLAN VLAN
41: GPON: 0/2/0

IPTV ETH3 8 4 11 5 8 200
20M/40M Uplink: 0/19/0

In this case the ONU is already added
⚫ Configure DBA profile
◼ OLT(config)#dba-profile add profile-id 11 type2 assure 2048
⚫ Modify ONT line profile
◼ OLT(config)# ont-lineprofile gpon profile-id 20
◼ OLT(config-gpon-lineprofile-20)#tcont 5 dba-profile-id 11
◼ OLT(config-gpon-lineprofile-20)#gem add 4 eth tcont 5
◼ OLT(config-gpon-lineprofile-20)#gem mapping 4 4 vlan 8
◼ OLT(config-gpon-lineprofile-20)#commit
⚫ Modify ONT service profile

◼ OLT(config)#ont-srvprofile gpon profile-id 30
◼ OLT(config-gpon-srvprofile-30)#ont-port eth 4 pots 2
◼ OLT(config-gpon-srvprofile-30)#port vlan eth 3 8
◼ OLT(config-gpon-srvprofile-30)#commit

⚫ Configure ONT native VLAN (Optional)
◼ OLT(config)# interface gpon 0/3
◼ OLT(config-if-gpon-0/3)#ont port native-vlan 0 2 eth 3 vlan 8
⚫ Configure traffic table

◼ OLT(config)#traffic table ip index 41 cir 20480 pir 40960 cbs 20480 pbs 40960
priority user-cos 5 priority-policy local-Setting
⚫ Provision VLANs
◼ OLT(config)#vlan 8 smart //Unicast VLAN
◼ OLT(config)#port vlan 8 0/19 0 Service port index
◼ OLT(config)#service-port 3 vlan 8 gpon 0/3/0 ont 2 gemport 4 multi-service

user-vlan 8 rx-cttr 41 tx-cttr 41

⚫ Configure the IGMP and multicast VLAN Service port index
◼ OLT(config)#btv
◼ OLT(config-bTV)#igmp user add service-port 3 no-auth
◼ OLT(config)#vlan 200 smart //Multicast VLAN
◼ OLT(config)#port vlan 200 0/19 0
◼ OLT(config)#multcast-vlan 200
◼ OLT(config-mvlan200)#igmp match mode disable
◼ OLT(config-mvlan200)#igmp mode proxy
◼ OLT(config-mvlan200)#igmp multicast-vlan member service-port 3
Service port index

Query the IGMP User
⚫ Query the IGMP user
 OLT(config)#display igmp user all
------------------------------------------------------------------------------
User port Bind State Auth Quick IGMP Video Log Available
profiles leave flow ID flow ID switch programs
------------------------------------------------------------------------------
0/3/0/2 - offline no-auth MAC-based 2 2 enable 8
0/3/0/3 - online no-auth MAC-based 3 3 enable 8
------------------------------------------------------------------------------

Questions
⚫ Is the Multicast VLAN can be different from Unicast VLAN?
⚫ Is it necessary to add programs manually?
⚫ How to add IGMP programs?

Contents

Query ONU Information (1/4)
◼ OLT(config-if-gpon-0/2)#display ont info 0 0
– --------------------------------------------
– F/S/P : 0/2/0
– ONT-ID : 0
– Control flag : active
– Run state : up
– Config state : normal
– Match state : match
– DBA type : SR
– ONT distance(m) : 186
– ONT battery state : support but invalid
– CPU occupation : -
– Temperature : -
– Authentic type : SN-auth
– SN : 48575443BF656E04 (2011-D659FD401)
– Management mode : OMCI
– ………
– Last down cause : -
– Last up time : 2012-02-04 15:50:34
– Last down time : -
– Last dying gasp time : -
– ………

– ---------------------------------------------------------
– Line profile ID : 20
– Line profile name : hg850
– ---------------------------------------------------------
– FEC upstream switch :Disable
– OMCC encrypt switch :Off
– Qos mode :PQ
– Mapping mode :VLAN
– VoIP config method :Default
– --------------------------------------------------------
– Notes: * indicates Discrete TCONT(TCONT UnBound)
– --------------------------------------------------------
– <T-CONT 0> DBA Profile-ID:1
– <T-CONT 5> DBA Profile-ID:11
– <Gem Index 3>
– --------------------------------------------------------
– |Serv-Type:ETH |Encrypt:off |Cascade:off |Priority:0 |GEM-CAR:-|
– ---------------------------------------------------------
– Mapping-index VLAN Priority Port-type Port-ID Flow-CAR
Transparent
– --------------------------------------------------------
– 3 200 - - - -
– 4 8 - - - -
– ---------------------------------------------------------

– -----------------------------------------------------------
– Service profile ID : 30
– Service profile name : hg850
– ----------------------------------------------------------
– Port-type Port-number
– ---------------------------------------------------------
– POTS 2
– ETH 4
– TDM 0
– MOCA 0
– CATV 0
– -------------------------------------------------------
– TDM port type : E1
– TDM service type : TDMoGem
– MAC learning function switch : Enable
– ONT transparent function switch : Disable
– Multicast forward mode : Untag
– ……
– Upstream IGMP packet forward VLAN : -
– Upstream IGMP packet priority : -
– Native VLAN option : Concern
– -------------------------------------------------------

— -----------------------------------------------------------
— Port Port Service-type Index S-VLAN S-PRI C-VLAN C-PRI ENCAP S-PRI
— type ID POLICY
— --------------------------------------------------------------------
— ETH 1 Translation 1 10 - 10 - - -
— ETH 2 Translation 1 200 - 200 - - -
— IPHOST 1 Translation 1 172 - 172 - - -
— --------------------------------------------------------------------
— Notes: * indicates transparent attribute of the vlan
— ----------------------------------------------------------------------
— Port-type Port-ID IGMP-mode IGMP-VLAN IGMP-PRI Max-MAC-Count
— --------------------------------------------------------------------
— ETH 1 - - - Unlimited
— --------------------------------------------------------------------
— Alarm policy profile ID : 0
— Alarm policy profile name : alarm-policy_0
— --------------------------------------------------------------------

Query VLAN
◼ OLT(config)#display vlan all
– -------------------------------------------------------------------
– VLAN Type Attribute STND-Port NUM SERV-Port NUM VLAN-Con NUM
– -------------------------------------------------------------------
– 1 smart common 2 0 -
– ---------------------------------------------------------------------
◼ OLT(config-if-gpon-0/2)#display ont port attribute 0 0 eth
– ---------------------------------------------------------------------
– ONT ONT ONT Auto-neg Speed Duplex Port Flow Native Priority
– port port-type (Mbps) switch control VLAN
– -------------------------------------------------------------------
– 0 1 ETH enable auto auto on off 10 0
– -------------------------------------------------------------------

Query Service VLAN
◼ OLT(config)#disiplay vlan 200
– VLAN ID: 200
– VLAN type: smart
– VLAN attribute: common
– VLAN description:
– VLAN forwarding mode in control board: VLAN-MAC
– VLAN forwarding mode: VLAN-MAC
– VLAN broadcast packet forwarding policy: forward
– VLAN unknown multicast packet forwarding policy: forward
– VLAN unknown unicast packet forwarding policy: forward
– VLAN bind service profile ID:-
– VLAN bind RAIO profile index: -
– VLAN priority: -
– -----------------------------
– F/S /P Native VLAN State
– -----------------------------
– 0/19/0 1 up
– -----------------------------
– Standard port number: 1
– ---------------------------------------------------------
– INDEX TYPE STATE F/ S/ P VPI VCI FLOWTYPE FLOWPARA
– ---------------------------------------------------------
– 2 gpon up 0 /2 /0 0 3 vlan 200
– -----------------------------------------------------------

Query IPTV IGMP Global Configuration
◼ OLT(config-btv)#display igmp config global
– --------------------------------------------------------
– Authorization : enable
– ……
– V3 General query response time(0.1s) : 100
– User action report switch : disable
– Preview switch : enable Recognition time(s) : 30
– The time of reset preview-count : 04:00:00
– Auto create log interval(h) : 2
– Uplink port mode : default
– Bandwidth management switch : enable
– CDR auto report interval(s) : 600
– CDR auto report number : 200 CDR switch : disable
– IGMP Packet encapsulation : all
– Router IP : 192.168.1.1
– Initial unsolicited report interval(s): 1
– Query offline user switch : disable

Query IPTV IGMP VLAN Configuration
◼ OLT(config-mvlan200)#display igmp config vlan 200
– ------------------------------------------------------
– IGMP mode : proxy
– IGMP version : IGMPv3
– Log switch : enable
– Default uplink port : -
– Report proxy switch : disable
– Leave proxy switch : disable
– Query proxy switch : enable
– Unsolicited report interval(s) : 10
– IGMP priority : 6
– Send global leave switch : enable
– Program match mode : disable
– Program match group : -
– IGMP inner-VLAN : 200
– IGMP video-mode : multicast
– IGMP group filter mode : ASM-SSM
– ……
– ------------------------------------------------------

Query IGMP Program
◼ OLT(config-mvlan200)#display igmp program all
– -----------------------------------------------------------
– Index| Create | IP | Program |User |VLAN |Prejoin| Priority
– | Flag | Address | name |num | ID | |
– -----------------------------------------------------------
– 0 S 224.1.1.1 PROGRAM-0 0 200 disable 7
– ……
– ---------------------------------------------------------
– Total: 1 program(s) (Static/Dynamic: 1/0) Note : # The program data

is valid, but it is no license or the uplink port ID is beyond number
of board port.

Query IGMP User and Member
◼ OLT(config－btv)#display igmp user all
– -----------------------------------------------------------
-
– User Port Bind State Auth Quick IGMP Video Log Available
– profiles leave flow ID flow ID switch
programs
– ----------------------------------------------------------
-
– 0/2/0/2 - online no-auth based MAC 2 - on 8
– 0/2/1/5 - offline no-auth based MAC 72 - on 16
– ----------------------------------------------------------
-
– Total: 3
◼ OLT(config-mvlan200#display igmp multicast-vlan member vlan 200

– BTV user(s) join the multicast vlan :
– -------------------------------------------------------
– 0/2/0/2 0/2/0/3 0/6/0/13 0/6/0/25
– -------------------------------------------------------
– Total: 4

Query IGMP Log Info
◼ OLT# display igmp log all
– { <cr>|verbos<K>||<K> }:
–
– Command:
– display igmp log all
– -------------------------------------------------------------
– Port Program IP/S VLAN Mode Join time Leave time
– --------------------------------------------------------------
– 0/3/0/1000 238.1.1.2 122 W 2011-06-09 2011-06-09
– 192.168.1.2 11:30:31+08:00 11:38:26+08:00
– 0/3/1/100 238.1.1.2 122 W 2011-06-09 2011-06-09
– 192.168.1.3 11:29:51+08:00 11:37:57+08:00
– ------------------------------------------------------------------
– Total: 2
– Note: P(Mode) indicates preview, W(Mode) indicates watch
– N(Mode) indicates no authority
– F(Mode) indicates preview times full out
OLT supports the log query based on IP/port/service port.

Query IGMP Message Statistics
◼ OLT(config)#display igmp statistic vlan 200
– The data of multicast-vlan 200 IGMP statistic:
– --------------------------------------------------------
– Receive general query number : 8
– Receive specific query number : 2
– …
– Receive V3 total join number : 3
– Receive successful V3 join number : 3
– Receive unsuccessful V3 join number : 0
– Receive leave number : 1
– …
– Send V3 join number : 3
– Send leave number : 1
– Active program number : 1
– Active user number : 2
– Receive invalid igmp packets : 0
– --------------------------------------------------------
– Note: The packets of igmp users not statistic in vlan

Query IPTV Multicast Stream Bandwidth
◼ OLT(config-mvlan200)#display multicast flow-statistic
– {index<K>|uplink-port<K>|vlan<K>}:vlan
– {vlanid<1,4093>}:200
– {ip<K>}:ip 224.1.1.1
– Command is being executed, please wait...
– Multicast flow statistic result: 2048(kbps)
◼ OLT(config-btv)#display multicast flow-statistic uplink-port 0/19/0

– Command is being executed, please wait...
– Multicast flow statistic result: 2704(kbps)
OLT supports the multicast stream bandwidth query based on program/uplink/VLAN

Query Traffic Statistics
◼ OLT(config-if-gpon-0/5)#display statistics
– {gemport<K>|ont-eth<K>|ont-gem<K>|ont-iphost<K>|
ont-line-quality<K>|ont-performance<K>|ont-
pots<K>|ont-priority-queue<K>|ont-
tdm<K>|ont<K>}:gemport
– {portid<0,7>}:0
– {ontid<0,127>}:0
– {gemindex<K>}:gemindex
– {gemindex<0,1023>}:2
– --------------------------------------------------
– Upstream frames : 78
– Upstream bytes : 15648
– Upstream discarded frames : 11
– Downstream frames : 528
– Downstream bytes : 35558
– Downstream discarded frames : 346367
– --------------------------------------------------
OLT supports the traffic query based on ont/gemport/ont-eth/ ont-line-quality

Questions
⚫ How to check the IGMP user status?
⚫ How to get the IGMP packet statistics?
⚫ How to check the IGMP configure of multicast?

Summary
⚫ Multicast Vlan
 Maximum : support 256 MVLANs
⚫ IGMP has two modes
 Proxy and snooping
 IGMP program supports static and dynamic modes
⚫ IGMP Version
 Support the V2/V3 protocol stack
⚫ IGMP User
 Support up to 8192 multicast users when these boards are used together

Thank you
www.huawei.com

4 Gpon FTTH Iptv Service Provisioning v8r13 Issue1.10 (S+N)

Uploaded by

Copyright:

Available Formats

4 Gpon FTTH Iptv Service Provisioning v8r13 Issue1.10 (S+N)

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

4 Gpon FTTH Iptv Service Provisioning v8r13 Issue1.10 (S+N)

Uploaded by

Copyright:

Available Formats

GPON FTTH IPTV

Copyright © Huawei Technologies Co., Ltd. All rights reserved.

 Master how to do the GPON FTTH IPTV service configuration

 Know the basic steps to check the GPON IPTV service

Copyright © Huawei Technologies Co., Ltd. All rights reserved. Page1

2. GPON IPTV Service Configuration Basics

3. GPON IPTV Service Configuration Example

4. GPON IPTV Service Maintenance

Copyright © Huawei Technologies Co., Ltd. All rights reserved. Page2

Headend CA System VOD EPG

Terminal Layer HOME GATEWAY

Copyright © Huawei Technologies Co., Ltd. All rights reserved. Page3

Step3 PON-OLT forward the multicast

Step2 terminal send

Copyright © Huawei Technologies Co., Ltd. All rights reserved. Page4

OLT M-VLAN IPTV

STB ONT VLAN8

STB ONT VLAN8 U-VLAN

Unicast VLAN Multicast

Copyright © Huawei Technologies Co., Ltd. All rights reserved. Page5

 System supports up to 4096 programs, including 2000 concurrently online

Copyright © Huawei Technologies Co., Ltd. All rights reserved. Page6

⚫ How many programs does a multicast user can watch

 A.4000 B. 256 C.32

⚫ What are the two IGMP modes?

Copyright © Huawei Technologies Co., Ltd. All rights reserved. Page7

2. GPON IPTV Service Configuration Basics

3. GPON IPTV Service Configuration Example

4. GPON IPTV Service Maintenance

Copyright © Huawei Technologies Co., Ltd. All rights reserved. Page8

Create DBA profile

Modify ont-lineprofile Add ONU procedure

Set ONU port native VLAN (Optional)

Copyright © Huawei Technologies Co., Ltd. All rights reserved. Page9

Provision multicast VLAN uplink

Provision IGMP mode and version

Provision multicast VLAN member

Copyright © Huawei Technologies Co., Ltd. All rights reserved. Page10

Copyright © Huawei Technologies Co., Ltd. All rights reserved. Page11

Copyright © Huawei Technologies Co., Ltd. All rights reserved. Page12

⚫ Set igmp uplink port in multicast vlan mode

//Specify an upstream port for sending and receiving multicast packets,

Copyright © Huawei Technologies Co., Ltd. All rights reserved. Page13

When the match mode is set as enable, multicast programs need to be

Copyright © Huawei Technologies Co., Ltd. All rights reserved. Page14

Copyright © Huawei Technologies Co., Ltd. All rights reserved. Page15

Copyright © Huawei Technologies Co., Ltd. All rights reserved. Page16

Copyright © Huawei Technologies Co., Ltd. All rights reserved. Page17

– Are you sure to change IGMP mode?(y/n)[n]:y

Copyright © Huawei Technologies Co., Ltd. All rights reserved. Page18

Copyright © Huawei Technologies Co., Ltd. All rights reserved. Page19

To pre-configure the multicast subscriber to simplify the configuration of

Copyright © Huawei Technologies Co., Ltd. All rights reserved. Page20

⚫ What’s the difference between igmp match mode enable and

Copyright © Huawei Technologies Co., Ltd. All rights reserved. Page21

2. GPON IPTV Service Configuration Basics

3. GPON IPTV Service Configuration Example

4. GPON IPTV Service Maintenance