Pni Ipmax3
Pni Ipmax3
English
• Simultaneous real-time multi-channel recording, remote playback and
configuration
• Supports up to 9 channels with a maximum 4K (8MP) resolution.
• Backup on USB flash memory and external HDD.
• Supports face and human shape detection (depending on the camera)
• Possibility to connect external speaker.
Technical specifications
NVR
Video inputs 4 x RJ45 POE
Video output 1 x VGA / 1 x HDMI
Audio output 1 x 3.5mm
Number of channels 9 x max. 4K (8MP)
Max. 2K (2560 x 1440) on HDMI output
Playback resolution
Max. 1080P (1920 x x1080) on VGA output
Ethernet 1 x RJ45 100/100Mbps
Video compression H.265AI/H.265+
Audio compression G.711A
Recording mode Manual, alarm, motion detection, programmed
USB 2 x USB2.0
HDD 1 x HDD SATA (max. 8Tb)
ONVIF Yes
Power voltage 48V / 2A
Dimensions 255 x 220 x 43 mm mm
Working temperature -26°C ~ +80°C
Camera
Resolution 3MP (2304 x 1296)
Lens 3.6mm
LED 4 IR LEDs and floodlight
Power supply POE
3 User manual
Dimensions 70 x 190 x 65 mm
Working temperature -26°C ~ +80°C
English
Before first use, please install the storage unit. Only one SATA HDD with a
maximum capacity of 14TB can be installed inside the recording unit (HDD is
not included in the package).
• Loosen the screws and open the NVR housing
• Connect the data cables and secure the hard drive with the screws
• Close back the NVR housing
• Connect the power and internet cable to the NVR
Special warnings:
1. Restart after power failure. If the device is closed abnormally, it creates a
User manual 4
backup and restarts from that status after power is restored.
2. Replace the battery on the system board. Before replacing the battery, you
English
must backup your system settings (see chapter Advanced-Import / Export)
and turn off the power supply. The device time and date must be set again after
the battery is replaced. We recommend that you replace the battery every
year.
Android iOS
The installation file can
be downloaded from
the CD included in the
Windows General CMS package or from the
Download section on the
product web page (www.
pni.ro)
System authentication
After turning on the device, log in to the system.
By default, the admin user is password protected by 1234. If the password is
entered incorrectly 5 times in a row, the account will be blocked. By restarting
the device or after half an hour, the account will be unlocked automatically.
Note: For the security of your system, please change the password after the first
login.
5 User manual
Quick setup guide
English
After starting the device, the quick setup guide will start.
Note: We recommend configuring the system before installing the NVR and
cameras in the final location.
Stept to follow:
1. Set the time, date and time zone.
2. Soon, a popup window will appear on the screen asking you to change the
authentication password in the system. Follow the steps on the screen or
press the ESC key on the NVR to exit the password setting interface.
Note: For the security of your system, we recommend changing the password after
the first login in the system.
3. Set the network parameters manually or activate the DHCP option for
automatic download.
4. Scan the QR code on the screen to install the XMEye application on your
mobile phone. Scan the QR code with the serial number to add the system
to the application.
5. Set the display options and resolution of the monitor connected to the
NVR. Maximum supported resolution 2560x1440 (2K).
Note: Before changing the resolution, make sure that your monitor supports that
resolution. If the set resolution is higher than the resolution of your monitor, nothing
will appear on the monitor and you will not be able to access the menu. If this
happens, however, connect the NVR to a lower resolution monitor, access the menu,
and change the resolution.
6. Press the OK key to complete the basic system configuration.
7. Right click on the screen and access the NetDetect option. Click Diagnose
to test the network configuration.
Note: For the settings to take effect, restart the system. Right click on the screen
- Logout - Reboot.
User manual 6
English
The menu
In the main preview interface, right-
click with the mouse to access the
menu.
Main Menu
Options: Playback, Record Conf, Network, Date Time.
7 User manual
Playback
English
The system offers numerous filters and options for identifying the desired
record. You can search by channel number, date and time interval or by file
type.
Record Conf.
The interface allows you to make the following settings: the length of a recording
file, the recording mode (programmed or manual), the period (day and time
interval) and the recording type (normal, motion detection and alarm).
User manual 8
Network
English
Manually set the network parameters (IP address, gateway, DNS, port, etc.)
or check the DHCP option for automatic parameter retrieval.
Note: For the settings to take effect, restart the system. Right click on the screen
- Logout - Reboot.
Date time
9 User manual
System
English
General
The interface will allow the following settings: the menu display language, the
behavior in case of a full hard disk (overwrite or stop recording), the session
duration and enable / disable quick configuration guide at system startup.
User manual 10
Encode
English
Displays the technical parameters of the connected cameras (resolution,
frame rate, video compression, quality, etc.).
Backup
The USB memory or external HDD must be installed in the NVR before
starting the backup. Press the Detect button to identify the storage device,
then the Backup button to perform the backup.
11 User manual
Snapshot Config
English
Set to take cyclic captures at a certain time and send them by email, FTP or
store them on your hard disk.
Display
In the local preview mode can be displayed: time, channel name, recording
status, alarm status, transparency and display resolution.
Note: Before changing the resolution, make sure that your monitor supports that
resolution. If the set resolution is higher than the resolution of your monitor, nothing
will appear on the monitor and you will not be able to access the menu. If this
happens, however, connect the NVR to a lower resolution monitor, access the menu,
and change the resolution.
User manual 12
English
Account
The interface allows managing users who have access to the system, adding
users, changing user rights, changing the password, creating user groups and
setting an account security level by registering answers to certain predefined
questions. In case of password reset, the verification code can be sent in the
mobile application or at the set email address. To increase security, you can set
a pattern for accessing the system.
13 User manual
Alarm
English
Intelligent Alert
User manual 14
Abnormality
English
Set the system behavior in case of: storage device error, lack of space on the
storage device, lack of internet connection or IP conflict. In such situations you
can set to send a notification in the application or an email.
Traditional alarm
Set the system behavior in case of missing image or missing video signal. In
such situations you can set to send a notification in the application or an email,
start recording, make captures or save the alarm recording on an FTP server.
15 User manual
Advanced
English
HDD info
User manual 16
Upgrade
English
Insert a USB stick into the NVR that should contain the update file in the
root folder. Select the storage drive and file from the NVR menu and click the
Upgrade button.
AutoMaintain
Set the system to restart on a certain day and time or set the automatic
deletion of files older than a certain period.
Restore
17 User manual
English
Import/Export
User manual 18
Digital
English
Options: Digital channels, Channel status and Channel Type.
Digital channels
Add a camera on a specific channel. Click the Add button, then Search to find
all the cameras connected in the same network (same router) with the NVR.
19 User manual
Channel status
English
Channel type
Displays the maximum number of cameras and the resolution of the cameras
that can be connected to the system. The PNI IPMAX POE 3 NVR supports
a maximum of 9 IP cameras with a maximum resolution of 4K (8MP).
User manual 20
Log
English
Displays the history of actions performed in the system.
Version
Displays useful information about firmware and QR code with the system
serial number (useful for adding it to the mobile application) and QR code for
downloading the mobile application.
21 User manual
Other menu options
English
Channel set
The interface allows adding and managing the cameras added to the system.
Channels interface
1. Delete. Delete the camera from the selected channel. Click Apply to run.
2. Clear. Delete the information on the selected channel. Click Apply to run.
3. Encode. Displays the technical parameters of the connected cameras
(resolution, frame rate, video compression, quality, etc.).
4. Edit devices. Change IP and port for the selected channel.
5. Bulk upgrade. Firmware update for selected cameras.
6. Network detect. Cloud network and server testing and diagnostics.
User manual 22
7. Channel title. Rename cameras.
8. NVR Network. Configure NVR network parameters.
English
9. Close adaptive. Disables the IP adaptation function for the selected cameras.
23 User manual
English
Record mode
Record mode
Face detection
The interface is only available for cameras that support this feature.
User manual 24
Color settings
English
Adjust color parameters (brightness, contrast, saturation, etc.) for the camera
viewing interface.
Split menu
Output Adjust
Net Detect
25 User manual
1. Local Net Detect. Camera connection monitoring and diagnostics.
English
s
2. Remote Net Detect. Monitoring, diagnostics and configuration of network
and Cloud server.
User manual 26
network.
English
Logout
27 User manual
Основни функции
Български
Технически спецификации
NVR
Видео входове 4 x RJ45 POE
Видео изход 1 x VGA / 1 x HDMI
Аудио изход 1 x 3.5mm
Брой канали 9 x max. 4K (8MP)
Резолюция на Макс. 2K (2560 x 1440) на HDMI изход
възпроизвеждане Макс. 1080P (1920 x 1080) на VGA изход
Ethernet 1 x RJ45 100/100Mbps
Видео компресия H.265AI/H.265+
Аудио компресия G.711A
Ръчно, аларма, детекция на движение,
Режим на запис
програмирано
USB 2 x USB2.0
HDD 1 x HDD SATA (max. 8Tb)
ONVIF Да
Захранващо 48V / 2A
напрежение
Размери 255 x 220 x 43 mm mm
Работна -26°C ~ +80°C
температура
Ръководство 28
Камера за видеонаблюдение
Български
Резолюция 3MP (2304 x 1296)
Лещи 3.6mm
LED 4 IR светодиода и прожектор
Захранване POE
Размери 70 x 190 x 65 mm
Работна -26°C ~ +80°C
температура
Инструкции за употреба
Включете устройството
Включете захранващия кабел в контакт 230V. NVR ще стартира.
Светодиодът на индикатора ще светне.
Ако времето за стартиране е в рамките на предварително зададения
график за запис, функцията за запис ще стартира автоматично.
Бележки:
1. Проверете дали входното напрежение съответства на препоръчаното
напрежение на устройството. Захранващото напрежение е 230V ± 10%
/ 50 Hz 2A.
2. Препоръчваме да използвате UPS устройство, за да предпазите
29 Ръководство
устройството от колебания на напрежението.
Български
Изключете устройството
Има два начина да изключите устройството.
1. Отворете главното меню (щракнете с десния бутон на екрана) и
изберете опцията Изход - Изключване
2. Изключете захранването.
Специални предупреждения:
1. Рестартирайте след спиране на захранването. Ако устройството е
затворено необичайно, то създава резервно копие и се рестартира от
това състояние след възстановяване на захранването.
2. Сменете батерията на системната платка. Преди да подмените
батерията, трябва да направите резервно копие на системните
настройки (вижте глава Advanced-Import / Export) и да изключите
захранването. Времето и датата на устройството трябва да бъдат
зададени отново след смяната на батерията. Препоръчваме ви да
сменяте батерията всяка година.
Операционна
Приложение Изтегли
система
Android iOS
Ръководство 30
Инсталационният
Български
файл може да
бъде изтеглен от
компактдиска,
Windows General CMS включен в пакета,
или от раздела
за изтегляне на
уеб страницата на
продукта (www.pni.bg)
Удостоверяване на системата
След включване на устройството влезте в системата.
По подразбиране потребителят на администратор е защитен с
парола от 1234. Ако паролата е въведена неправилно 5 пъти подред,
акаунтът ще бъде блокиран. Чрез рестартиране на устройството или
след половин час акаунтът ще бъде отключен автоматично.
Ръководство 32
Менюто
Български
В основния интерфейс за
визуализация щракнете с десния
бутон на мишката, за да влезете
в менюто.
Playback (Възпроизвеждане)
Network (Мрежа)
Задайте ръчно мрежовите параметри (IP адрес, шлюз, DNS, порт и т.н.)
или проверете опцията DHCP за автоматично извличане на параметри.
Ръководство 34
Забележка: За да влязат в сила настройките, рестартирайте системата.
Български
Щракнете с десния бутон върху екрана - Logout - Reboot.
System (Система)
Настроики: General, Encode, Backup, Snapshot Config., Display, Account.
35 Ръководство
Български
General (Общ)
Ръководство 36
Encode (Кодиране)
Български
Показва техническите параметри на свързаните камери (резолюция,
честота на кадрите, видео компресия, качество и др.).
Backup (Архивиране)
37 Ръководство
Snapshot Config
Български
Display (Дисплей)
Ръководство 38
Български
Account (Сметка)
39 Ръководство
Български
Alarm (Аларма)
Настроики: Intelligent Alert, Abnormality и Traditional alarm (Няма
изображение, няма видео сигнал и т.н.). Аларма и интелигентни
опции не са налични за този модел.
Български
Abnormality (Ненормалност)
41 Ръководство
Traditional alarm (Традиционна аларма)
Български
Advanced (Разширено)
Настроики: HDD info, Upgrade, AutoMaintain, Restore, Import / Export,
Digital, LOG, BPS и Version.
Ръководство 42
HDD info (Информация за HDD)
Български
Задайте как работи твърдият диск (само за четене или за четене и запис).
Забележка: За да запишете записите на твърдия диск, той трябва да
бъде настроен на режим на четене / запис.
43 Ръководство
AutoMaintain
Български
Restore (Нулиране)
Ръководство 44
Български
Digital (Дигитален)
Version (Версия)
Български
щракнете върху Добави, за да ги добавите в системата.
4. Network. Конфигуриране на мрежови параметри за камери (IP
адрес, шлюз и др.)
5. Quick set. Бързо добавяне и конфигуриране на камери.
6. IP Bulk Modify. Бърза смяна на IP към множество камери.
Интерфейс на каналите
1. Delete. Изтрийте камерата от избрания канал. Щракнете върху
Приложи, за да стартирате.
2. Clear. Изтрийте информацията от избрания канал. Щракнете върху
Приложи, за да стартирате.
3. Encode. Показва техническите параметри на свързаните камери
(резолюция, честота на кадрите, видео компресия, качество и др.).
4. Edit devices. Променете IP и порт за избрания канал.
5. Bulk upgrade. Актуализация на фърмуера за избрани камери.
6. Network detect. Тестване и диагностика на облачна мрежа и сървър.
7. Channel title. Преименувайте камерите.
8. NVR Network. Конфигурирайте мрежовите параметри на NVR.
9. Close adaptive. Деактивира функцията за IP адаптация за избраните
камери.
49 Ръководство
Български
Ръководство 50
Български
Playback (Възпроизвеждане)
51 Ръководство
Split menu (Разделено меню)
Български
Изходна настройка
Net Detect
Български
3. Net traffic Detect. Мониторинг на трафика на данни, извършван от
NVR в мрежата.
53 Ръководство
Hauptfunktionen
Deutsche
Technische Spezifikationen
NVR
Videoeingänge 4 x RJ45 POE
Video-Ausgang 1 x VGA / 1 x HDMI
Audioausgang 1 x 3.5mm
Anzahl der Kanäle 9 x max. 4K (8MP)
max. 2K (2560 x 1440) am HDMI-Ausgang
Wiedergabeauflösung
max. 1080P (1920 x x1080) am VGA-Ausgang
Ethernet 1 x RJ45 100/100Mbps
Video-Kompression H.265AI/H.265+
Audiokomprimierung G.711A
Manuell, Alarm, Bewegungserkennung,
Aufnahmemodus
programmiert
USB 2 x USB2.0
HDD 1 x HDD SATA (max. 8Tb)
ONVIF Jawohl
Netzspannung 48V / 2A
Maße 255 x 220 x 43 mm mm
Arbeitstemperatur -26°C ~ +80°C
Überwachungskamera
Auflösung 3MP (2304 x 1296)
Linse 3.6mm
LED 4 IR-LEDs und Flutlicht
Benutzerhandbuch 54
Energieversorgung POE
Deutsche
Maße 70 x 190 x 65 mm
Arbeitstemperatur -26°C ~ +80°C
Gebrauchsanweisung
Einbau der Speichereinheit
Bitte installieren Sie vor dem ersten Gebrauch die Speichereinheit. In der
Aufnahmeeinheit kann nur eine SATA-Festplatte mit einer maximalen
Kapazität von 14 TB installiert werden (Festplatte ist nicht im Lieferumfang
enthalten).
• Lösen Sie die Schrauben und öffnen Sie das NVR-Gehäuse
• Schließen Sie die Datenkabel an und befestigen Sie die Festplatte mit
den Schrauben
• Schließen Sie das NVR-Gehäuse wieder
• Verbinden Sie das Strom- und Internetkabel mit dem NVR
55 Benutzerhandbuch
2. Schalten Sie die Stromversorgung aus.
Deutsche
Besondere Warnhinweise:
1. Neustart nach Stromausfall. Wenn das Gerät abnormal geschlossen wird,
erstellt es ein Backup und startet von diesem Status aus neu, nachdem die
Stromversorgung wiederhergestellt wurde.
2. Ersetzen Sie die Batterie auf der Systemplatine. Vor dem Batteriewechsel
müssen Sie Ihre Systemeinstellungen sichern (siehe Kapitel Advanced-Import
/ Export) und die Stromversorgung ausschalten. Nach dem Batteriewechsel
müssen Uhrzeit und Datum des Geräts neu eingestellt werden. Wir empfehlen,
die Batterie jedes Jahr auszutauschen.
Android iOS
Die Installationsdatei
kann von der im
Paket enthaltenen
CD oder aus dem
Windows General CMS
Download-Bereich auf
der Produktwebseite
(www.mypni.de)
heruntergeladen werden.
Benutzerhandbuch 56
Systemauthentifizierung
Deutsche
Melden Sie sich nach dem Einschalten des Geräts am System an.
Standardmäßig ist der Admin-Benutzer durch 1234 passwortgeschützt. Wenn
das Passwort 5 Mal hintereinander falsch eingegeben wird, wird das Konto
gesperrt. Durch Neustart des Gerätes oder nach einer halben Stunde wird der
Account automatisch entsperrt.
Hinweis: Bitte ändern Sie zur Sicherheit Ihres Systems das Passwort nach der ersten
Anmeldung.
Nach dem Starten des Geräts wird die Kurzanleitung zur Einrichtung gestartet.
Hinweis: Wir empfehlen, das System zu konfigurieren, bevor Sie den NVR und die
Kameras am endgültigen Standort installieren.
Schritte zum folgen:
1. Stellen Sie Uhrzeit, Datum und Zeitzone ein.
2. Bald erscheint auf dem Bildschirm ein Popup-Fenster, in dem Sie
aufgefordert werden, das Authentifizierungskennwort im System zu
ändern. Befolgen Sie die Schritte auf dem Bildschirm oder drücken Sie
die ESC-Taste auf dem NVR, um die Passworteinstellungsoberfläche zu
verlassen.
Hinweis: Zur Sicherheit Ihres Systems empfehlen wir, das Passwort nach der ersten
Anmeldung am System zu ändern .
3. Stellen Sie die Netzwerkparameter manuell ein oder aktivieren Sie die
DHCP-Option für den automatischen Download.
4. Scannen Sie den QR-Code auf dem Bildschirm, um die XMEye-Anwendung
auf Ihrem Mobiltelefon zu installieren. Scannen Sie den QR-Code mit der
Seriennummer, um das System zur Anwendung hinzuzufügen.
5. Stellen Sie die Anzeigeoptionen und die Auflösung des an den NVR
angeschlossenen Monitors ein. Maximal unterstützte Auflösung
2560x1440 (2K) .
Hinweis: Stellen Sie vor dem Ändern der Auflösung sicher, dass Ihr Monitor diese
Auflösung unterstützt. Wenn die eingestellte Auflösung höher als die Auflösung
Ihres Monitors ist, wird nichts auf dem Monitor angezeigt und Sie können nicht auf
das Menü zugreifen. Wenn dies jedoch passiert, schließen Sie den NVR an einen
57 Benutzerhandbuch
Monitor mit niedrigerer Auflösung an, rufen Sie das Menü auf und ändern Sie die
Auflösung .
Deutsche
Das Menü
Klicken Sie in der
Hauptvorschauoberfläche mit der
rechten Maustaste, um auf das Menü
zuzugreifen.
Benutzerhandbuch 58
Main Menu (Hauptmenü)
Deutsche
Optionen: Playback, Record Conf, Network, Date Time.
Playback (Wiedergabe)
59 Benutzerhandbuch
Record Conf. (Aufnahmekonfiguration)
Deutsche
Network (Netzwerk)
Benutzerhandbuch 60
Deutsche
Date time (Datum und Uhrzeit)
System (System)
Optionen: General, Encode, Backup, Snapshot Config., Display, Account.
61 Benutzerhandbuch
Deutsche
General (Allgemeines)
Encode (Kodieren)
Der USB-Speicher oder die externe Festplatte muss im NVR installiert sein,
bevor die Sicherung gestartet wird. Drücken Sie die Detect-Taste, um das
Speichergerät zu identifizieren, und dann die Backup-Taste, um die Sicherung
durchzuführen.
Snapshot-Konfiguration
Display (Anzeige)
Benutzerhandbuch 64
Deutsche
Account (Konto)
65 Benutzerhandbuch
Alarm (Alarm)
Deutsche
Optionen: Intelligent Alert, Abnormality and Traditional alarm (Kein Bild, kein
Videosignal usw.). Alarmeingang und intelligente Optionen sind für dieses
Modell nicht verfügbar.
Benutzerhandbuch 66
Abnormality (Anomalie)
Deutsche
Legen Sie das Systemverhalten fest bei: Speichergerätefehler, Platzmangel
auf dem Speichergerät, fehlende Internetverbindung oder IP-Konflikt. In
solchen Situationen können Sie festlegen, dass eine Benachrichtigung in der
Anwendung oder eine E-Mail gesendet wird.
67 Benutzerhandbuch
Advanced (Fortgeschritten)
Deutsche
Legen Sie fest, wie die Festplatte funktioniert (nur Lesen oder Lesen/
Schreiben).
Hinweis: Um Aufnahmen auf der Festplatte zu speichern, muss diese auf den Lese-/
Schreibmodus eingestellt sein.
Benutzerhandbuch 68
Upgrade (Aktualisierung)
Deutsche
Stecken Sie einen USB-Stick in den NVR, der die Update-Datei im
Stammordner enthalten sollte. Wählen Sie das Speicherlaufwerk und die Datei
aus dem NVR-Menü aus und klicken Sie auf die Schaltfläche Upgrade.
AutoMaintain
Stellen Sie das System so ein, dass es an einem bestimmten Tag und einer
bestimmten Uhrzeit neu startet oder stellen Sie das automatische Löschen von
Dateien ein, die älter als ein bestimmter Zeitraum sind.
Restore (Zurücksetzen)
Import/Export
Benutzerhandbuch 70
Digital
Deutsche
Optionen: Digital channels, Channel status und Channel Type.
Fügen Sie eine Kamera auf einem bestimmten Kanal hinzu. Klicken Sie auf die
Schaltfläche Hinzufügen und dann auf Suchen, um alle Kameras zu finden, die
im selben Netzwerk (gleicher Router) mit dem NVR verbunden sind.
71 Benutzerhandbuch
Channel status (Kanalstatus)
Deutsche
Zeigt den Status (verbunden, nicht verbunden oder nicht konfiguriert) für alle
9 Kanäle an.
Zeigt die maximale Anzahl von Kameras und die Auflösung der Kameras an,
die an das System angeschlossen werden können. Der PNI IPMAX POE 3
NVR unterstützt maximal 9 IP-Kameras mit einer maximalen Auflösung von
4K (8MP).
Benutzerhandbuch 72
Log
Deutsche
Zeigt den Verlauf der im System ausgeführten Aktionen an.
Ausführung
73 Benutzerhandbuch
Andere Menüoptionen
Deutsche
Die Schnittstelle ermöglicht das Hinzufügen und Verwalten der zum System
hinzugefügten Kameras.
Kameraschnittstelle hinzufügen
1. Wählen Sie das Kommunikationsprotokoll zwischen dem NVR und den
Kameras aus. Optionen: NETIP, ONVIF, Full Netcom.
2. Search. Drücken Sie die Suchtaste, um nach Kameras zu suchen, die mit
dem gleichen Router (dem gleichen Netzwerk) wie der NVR verbunden sind.
3. Add. Wählen Sie aus der Liste der angezeigten Kameras die gewünschten
Kameras aus und klicken Sie auf Hinzufügen, um sie dem System hinzuzufügen.
4. Network. Konfigurieren Sie Netzwerkparameter für Kameras (IP-Adresse,
Gateway usw.)
5. Quick set. Schnelles Hinzufügen und Konfigurieren von Kameras.
6. IP Bulk Modify. Schneller Wechsel der IP zu mehreren Kameras.
Kanäle-Schnittstelle
1. Delete. Löschen Sie die Kamera aus dem ausgewählten Kanal. Klicken Sie
zum Ausführen auf Übernehmen.
2. Clear. Löschen Sie die Informationen zum ausgewählten Kanal. Klicken Sie
zum Ausführen auf Übernehmen.
3. Encode. Zeigt die technischen Parameter der angeschlossenen Kameras
(Auflösung, Bildrate, Videokompression, Qualität etc.).
Benutzerhandbuch 74
4. Edit devices. IP und Port für den ausgewählten Kanal ändern.
5. Bulk upgrade. Firmware-Update für ausgewählte Kameras.
Deutsche
6. Network detect. Tests und Diagnose von Cloud-Netzwerken und -Servern.
7. Channel title. Kameras umbenennen.
8. NVR Network. Konfigurieren Sie die NVR-Netzwerkparameter.
9. Close adaptive. Deaktiviert die IP-Anpassungsfunktion für die ausgewählten
Kameras.
75 Benutzerhandbuch
Deutsche
Stellen Sie den Aufnahmemodus (manuell oder programmiert) für jeden Kanal
ein.
Playback (Wiedergabe)
Verknüpfung für den Zugriff auf die Such- und Wiedergabeoberfläche von
Aufzeichnungen.
Die Schnittstelle ist nur für Kameras verfügbar, die diese Funktion unterstützen.
Benutzerhandbuch 76
Farbeinstellungen
Deutsche
Passen Sie die Farbparameter (Helligkeit, Kontrast, Sättigung usw.) für die
Kameraanzeigeschnittstelle an.
Menü aufteilen
Wählen Sie aus, wie die Kameras auf demselben Bildschirm angezeigt werden
sollen.
77 Benutzerhandbuch
Net Detect
Deutsche
s
2. Remote Net Detect. Überwachung, Diagnose und Konfiguration von
Netzwerk und Cloud-Server.
Benutzerhandbuch 78
3. Net traffic Detect. Überwachung des vom NVR durchgeführten
Datenverkehrs im Netzwerk.
Deutsche
Ausloggen
Melden Sie sich ab, fahren Sie das System herunter oder starten Sie es neu.
79 Benutzerhandbuch
Funciones principales
Español
Especificaciones técnicas
NVR
Entradas de video 4 x RJ45 POE
Salida de video 1 x VGA / 1 x HDMI
Salida de audio 1 x 3.5mm
Número de canales 9 x max. 4K (8MP)
Resolución de Max. 2K (2560 x 1440) en salida HDMI
reproducción Max. 1080P (1920 x x1080) en salida VGA
Ethernet 1 x RJ45 100/100Mbps
Compresión de video H.265AI/H.265+
Compresión de audio G.711A
Manual, alarma, detección de movimiento,
Modo grabación
programado
USB 2 x USB2.0
HDD 1 x HDD SATA (max. 8Tb)
ONVIF Si
Voltaje de potencia 48V / 2A
Dimensiones 255 x 220 x 43 mm mm
Temperatura de -26°C ~ +80°C
trabajo
Cámara de vigilancia
Resolución 3MP (2304 x 1296)
Lente 3.6mm
DIRIGIÓ 4 LED IR y reflector
Manual de usuario 80
Fuente de POE
alimentación
Español
Dimensiones 70 x 190 x 65 mm
Temperatura de -26°C ~ +80°C
trabajo
Instrucciones de uso
Instalación de la unidad de almacenamiento
Enciende el dispositivo
Enchufe el cable de alimentación en una toma de 230V. Se iniciará el NVR. El
LED indicador se iluminará. De forma predeterminada, se mostrarán 9 canales
en la pantalla.
Si la hora de inicio está dentro del programa preestablecido para la grabación,
la función de grabación se iniciará automáticamente
Notas:
1. Verifique que el voltaje de entrada corresponda al voltaje recomendado del
dispositivo. La tensión de alimentación es 230V ± 10% / 50 Hz 2A.
2. Sugerimos usar un dispositivo UPS para proteger el dispositivo de las fluctuaciones
de voltaje.
Apagar el dispositivo
Hay dos formas de apagar el dispositivo.
1. Acceda al menú principal (clic derecho en la pantalla) y seleccione la opción
Cerrar sesión - Apagar
81 Manual de usuario
2. Apague la fuente de alimentación.
Español
Advertencias especiales:
1. Reinicie después de un corte de energía. Si el dispositivo se cierra de manera
anormal, crea una copia de seguridad y se reinicia desde ese estado después de
que se restablece la energía.
2. Reemplace la batería en la placa del sistema. Antes de reemplazar la batería,
debe hacer una copia de seguridad de la configuración del sistema (consulte el
capítulo Importación / exportación avanzada) y apagar la fuente de alimentación.
La hora y la fecha del dispositivo se deben configurar nuevamente después de
reemplazar la batería. Le recomendamos que reemplace la batería todos los
años.
Android iOS
El archivo de instalación
se puede descargar
desde el CD incluido
Windows General CMS en el paquete o desde
la sección de Descargas
en la página web del
producto (www.pni.es)
Español
seguidas, la cuenta será bloqueada. Al reiniciar el dispositivo o después de
media hora, la cuenta se desbloqueará automáticamente.
El menú
En la interfaz de vista previa principal,
haga clic con el botón derecho del
ratón para acceder al menú.
Manual de usuario 84
Español
Playback (Reproducción)
85 Manual de usuario
y alarma).
Español
Network (red)
Manual de usuario 86
Date time (Fecha y hora)
Español
Establezca la zona horaria, la fecha, la hora y el formato.
System (Sistema)
Opciones: General, Encode, Backup, Snapshot Config., Display, Account.
General
Encode (Codifica)
Backup (Respaldo)
La memoria USB o el disco duro externo deben estar instalados en el NVR antes
Manual de usuario 88
de iniciar la copia de seguridad. Presione el botón Detectar para identificar el
dispositivo de almacenamiento, luego el botón Copia de seguridad para realizar
Español
la copia de seguridad.
89 Manual de usuario
Display (Monitor)
Español
En el modo de vista previa local se puede mostrar: hora, nombre del canal,
estado de grabación, estado de alarma, transparencia y resolución de pantalla.
Nota: antes de cambiar la resolución, asegúrese de que su monitor admita esa
resolución. Si la resolución establecida es superior a la resolución de su monitor,
no aparecerá nada en el monitor y no podrá acceder al menú. Sin embargo, si esto
sucede, conecte el NVR a un monitor de menor resolución, acceda al menú y cambie
la resolución.
Account (Cuenta)
Manual de usuario 90
Español
Alarm (Alarma)
Opciones: Intelligent Alert, Abnormality and Traditional alarm (Sin imagen,
sin señal de video, etc.). La entrada de alarma y las opciones inteligentes no
están disponibles para este modelo.
91 Manual de usuario
sensibilidad al movimiento y el área de acción.
Español
Abnormality (Anomalía)
Español
capturas o guardar la grabación de alarma en un servidor FTP.
Advanced (Avanzado)
Opciones: HDD info, Upgrade, AutoMaintain, Restore, Import / Export,
Digital, LOG, BPS y Version.
Upgrade
AutoMaintain
Español
Reset
Importación y exportación
95 Manual de usuario
Español
Digital
Manual de usuario 96
Español
Channel status (Estado del canal)
97 Manual de usuario
Español
Log
Version (Versión)
Manual de usuario 98
Español
Otras opciones de menú
Haga clic derecho en la pantalla para
mostrar opciones adicionales:
Channel Set, Record Mode,
Playback, Face detection, IPC
parameters, Color settings, Split
menu, PTZ Control, Output adjust,
NetDetect, Logout.
Interfaz de canales
1. Delete. Elimina la cámara del canal seleccionado. Haga clic en Aplicar para
ejecutar.
2. Clear.Elimina la información del canal seleccionado. Haga clic en Aplicar
para ejecutar.
3. Encode. Muestra los parámetros técnicos de las cámaras conectadas
(resolución, velocidad de cuadros, compresión de video, calidad, etc.).
4. Edit devices. Cambiar IP y puerto para el canal seleccionado.
5. Bulk upgrade. Actualización de firmware para cámaras seleccionadas.
6. Network detect. Pruebas y diagnósticos de servidores y redes en la nube.
7. Channel title. Cambiar el nombre de las cámaras.
8. NVR Network. Configurar los parámetros de red del NVR.
9. Close adaptive. Desactiva la función de adaptación de IP para las cámaras
seleccionadas.
Playback (Reproducción)
La interfaz solo está disponible para cámaras que admitan esta función.
Español
Output Adjust (Ajustes de imagen)
Net Detect
s
2. Remote Net Detect. Monitorización, diagnóstico y configuración de red y
servidor Cloud.
103 Manual de usuario
Español
3. Net traffic Detect. Monitoreo del tráfico de datos realizado por NVR en la
red.
Français
• Enregistrement multicanal simultané en temps réel, lecture et configuration
à distance
• Prend en charge jusqu’à 9 canaux avec une résolution maximale de 4K
(8MP).
• Sauvegarde sur mémoire flash USB et disque dur externe.
• Prend en charge la détection de visage et de forme humaine (selon la
caméra)
• Possibilité de connecter un haut-parleur externe.
Spécifications techniques
NVR
Entrées vidéo 4 x RJ45 POE
Sortie vidéo 1 x VGA / 1 x HDMI
Sortie audio 1 x 3.5mm
Nombre de canaux 9 x max. 4K (8MP)
Max. 2K (2560 x 1440) sur sortie HDMI
Résolution de lecture
Max. 1080P (1920 x x1080) sur sortie VGA
Ethernet 1 x RJ45 100/100Mbps
Compression de vidéo H.265AI/H.265+
Compression audio G.711A
Mode Manuel, alarme, détection de mouvement,
d'enregistrement programmé
USB 2 x USB2.0
Disque dur 1 x HDD SATA (max. 8Tb)
ONVIF Oui
Tension d'alimentation 48V / 2A
Dimensions 255 x 220 x 43 mm mm
Température de -26°C ~ +80°C
fonctionnement
Caméra de surveillance
Résolution 3MP (2304 x 1296)
105 Manuel utilisateur
Lentille 3.6mm
LED 4 LED IR et projecteur
Français
Mode d’emploi
Installation de l’unité de stockage
Allumez l’appareil
Branchez le cordon d’alimentation dans une prise 230V. Le NVR démarrera.
L’indicateur LED s’allumera.
Si l’heure de début se situe dans le calendrier prédéfini pour l’enregistrement,
la fonction d’enregistrement démarrera automatiquement.
Remarques:
1. Vérifiez que la tension d’entrée correspond à la tension recommandée de l’appareil.
La tension d’alimentation est de 230V ± 10% / 50 Hz 2A.
2. Nous vous suggérons d’utiliser un onduleur pour protéger l’appareil des fluctuations
de tension.
Éteignez l’appareil
Il existe deux façons d’éteindre l’appareil.
1. Accédez au menu principal (clic droit sur l’écran) et sélectionnez l’option
Déconnexion - Arrêt
Manuel utilisateur 106
2. Coupez l’alimentation.
Français
Mises en garde spéciales:
1. Redémarrez après une panne de courant. Si l’appareil est fermé de manière
anormale, il crée une sauvegarde et redémarre à partir de cet état une fois
l’alimentation rétablie.
2. Remplacez la batterie sur la carte système. Avant de remplacer la batterie,
vous devez sauvegarder les paramètres de votre système (voir chapitre
Advanced-Import / Export) et couper l’alimentation. L’heure et la date de
l’appareil doivent être à nouveau réglées après le remplacement de la batterie.
Nous vous recommandons de remplacer la batterie chaque année.
Télécommande de l’appareil
Le NVR peut être contrôlé localement ou à distance à partir de smartphones
et d’ordinateurs dotés du système d’exploitation Windows.
Android iOS
Le fichier d’installation
peut être téléchargé
à partir du CD inclus
dans l’emballage ou
Windows General CMS
à partir de la section
Téléchargement de la
page Web du produit
(www.pni.fr)
Authentification du système
Après avoir allumé l’appareil, connectez-vous au système.
Par défaut, l’utilisateur admin est protégé par mot de passe par 1234. Si
107 Manuel utilisateur
le mot de passe est mal saisi 5 fois de suite, le compte sera bloqué. En
redémarrant l’appareil ou après une demi-heure, le compte sera déverrouillé
Français
automatiquement.
Remarque : Pour la sécurité de votre système, veuillez changer le mot de passe après
la première connexion.
Français
Le menu
Dans l’interface principale de
prévisualisation, faites un clic droit
avec la souris pour accéder au menu.
Playback (Relecture)
Français
Network (Réseau)
System (Système)
Options: General, Encode, Backup, Snapshot Config., Display, Account.
Français
L’interface permettra les réglages suivants : la langue d’affichage du menu, le
comportement en cas de disque dur plein (écraser ou arrêter l’enregistrement),
la durée de la session et activer/désactiver le guide de configuration rapide au
démarrage du système.
Encode (Encoder)
La mémoire USB ou le disque dur externe doit être installé dans le NVR avant
de démarrer la sauvegarde. Appuyez sur le bouton Détecter pour identifier
le périphérique de stockage, puis sur le bouton Sauvegarder pour effectuer la
sauvegarde.
Français
Dans le mode de prévisualisation local peuvent être affichés : l’heure, le nom
du canal, l’état de l’enregistrement, l’état de l’alarme, la transparence et la
résolution d’affichage.
Remarque : avant de modifier la résolution, assurez-vous que votre moniteur prend
en charge cette résolution. Si la résolution définie est supérieure à la résolution de
votre moniteur, rien n’apparaîtra sur le moniteur et vous ne pourrez pas accéder au
menu. Si cela se produit, connectez le NVR à un moniteur de résolution inférieure,
accédez au menu et modifiez la résolution.
Account (Compte)
Alarm (Alarme)
Options: Intelligent Alert, Abnormality and Traditional alarm (Pas d’image,
Pas de signal vidéo, etc.). L’entrée d’alarme et les options intelligentes ne sont
pas disponibles pour ce modèle.
Français
Abnormality (Anomalie)
Advanced (Avancée)
Options: HDD info, Upgrade, AutoMaintain, Restore, Import / Export,
Digital, LOG, BPS et Version.
Français
Définissez le fonctionnement du disque dur (lecture seule ou lecture-écriture).
Remarque : Afin de sauvegarder les enregistrements sur le disque dur, celui-ci doit
être réglé en mode lecture/écriture.
Upgrade
Insérez une clé USB dans le NVR qui doit contenir le fichier de mise à jour
dans le dossier racine. Sélectionnez le lecteur de stockage et le fichier dans le
menu NVR et cliquez sur le bouton Upgrade.
Restore (Réinitialiser)
Import/Export
Ajouter une caméra sur un canal spécifique. Cliquez sur le bouton Ajouter, puis
sur Rechercher pour trouver toutes les caméras connectées au même réseau
(même routeur) avec le NVR.
État du canal
Affiche l’état (connecté, non connecté ou non configuré) pour les 9 canaux.
Version
Ajouter de caméras
1. Sélectionnez le protocole de communication entre le NVR et les caméras.
Options: NETIP, ONVIF, Full Netcom.
2. Search. Appuyez sur la touche Rechercher pour rechercher des caméras
connectées au même routeur (même réseau) que le NVR.
Manuel utilisateur 124
3. Add. Dans la liste des caméras affichées, sélectionnez les caméras souhaitées
et cliquez sur Ajouter pour les ajouter au système.
Français
4. Network. Configurer les paramètres réseau des caméras (adresse IP,
passerelle, etc.)
5. Quick set. Ajout et configuration rapide de caméras.
6. IP Bulk Modify. Changement rapide d’IP à plusieurs caméras.
L’interface n’est disponible que pour les caméras prenant en charge cette
fonctionnalité.
Output Adjust
Net Detect
Français
3. Net traffic Detect. Surveillance du trafic de données effectué par le NVR
dans le réseau.
Műszaki adatok
NVR
Videó bemenetek 4 x RJ45 POE
Videó kimenet 1 x VGA / 1 x HDMI
Hang kimenet 1 x 3.5mm
Csatornák száma 9 x max. 4K (8MP)
Max. 2K (2560 x 1440) a HDMI kimeneten
Lejátszási felbontás
Max. 1080P (1920 x 1080) VGA kimeneten
Ethernet 1 x RJ45 100/100Mbps
Videó tömörítés H.265AI/H.265+
Hangtömörítés G.711A
Felvételi mód Manuális, riasztó, mozgásérzékelés, programozott
USB 2 x USB2.0
HDD 1 x HDD SATA (max. 8Tb)
ONVIF Igen
Tápfeszültség 48V / 2A
Méretek 255 x 220 x 43 mm mm
Üzemhőmérséklet -26°C ~ +80°C
Térfigyelő kamera
Felbontás 3MP (2304 x 1296)
Lencse 3.6mm
VEZETTE 4 IR LED és reflektor
Tápegység POE
Méretek 70 x 190 x 65 mm
Magyar
Használati útmutató
A tárolóegység telepítése
Az első használat előtt telepítse a tároló egységet. Csak egy SATA HDD-t
lehet beépíteni a maximálisan 14 TB kapacitású felvevőegységbe (a HDD-t
nem tartalmazza a csomag).
• Lazítsa meg a csavarokat, és nyissa ki az NVR házát
• Csatlakoztassa az adatkábeleket és rögzítse a merevlemezt a csavarokkal
• Zárja vissza az NVR házát
• Csatlakoztassa a táp- és internetkábelt az NVR-hez
Kapcsolja be a készüléket
Csatlakoztassa a tápkábelt egy 230 V-os konnektorhoz. Az NVR elindul. A
jelző LED kigyullad.
Ha a kezdési idő a rögzítés előre beállított ütemezésén belül van, akkor a
felvételi funkció automatikusan elindul.
Megjegyzések:
1. Ellenőrizze, hogy a bemeneti feszültség megfelel-e a készülék ajánlott
feszültségének. A tápfeszültség 230V ± 10% / 50 Hz 2A.
2. Javasoljuk, hogy használjon UPS-készüléket, hogy megvédje a készüléket a
feszültségingadozásoktól.
Kapcsolja ki a készüléket
Két módon kapcsolhatja ki az eszközt.
1. Nyissa meg a főmenüt (kattintson a jobb gombbal a képernyőn), és válassza
a Kijelentkezés - Leállítás lehetőséget
2. Kapcsolja ki az áramellátást.
Különleges figyelmeztetések:
1. Áramszünet után indítsa újra. Ha az eszköz rendellenesen zárva van,
biztonsági másolatot hoz létre, és az áramellátás helyreállítása után újraindul
A készülék távvezérlése
Az NVR helyileg vagy távolról vezérelhető mind okostelefonokról, mind
Windows operációs rendszerrel rendelkező számítógépekről.
Android iOS
A telepítőfájl letölthető
a csomagban található
Windows General CMS CD-ről, vagy a termék
weboldalának (www.pni.
hu) Letöltés részéről.
A rendszer hitelesítése
A készülék bekapcsolása után jelentkezzen be a rendszerbe.
Alapértelmezés szerint az adminisztrátort az 1234. jelszóval védi. Ha a jelszót
egymás után ötször helytelenül adják meg, a fiók blokkolásra kerül. Az eszköz
újraindításával vagy fél óra elteltével a fiók automatikusan feloldódik.
Magyar
A készülék elindítása után elindul a gyors telepítési útmutató.
Megjegyzés: Az NVR és a kamerák végleges telepítése előtt javasoljuk a
rendszer konfigurálását.
Követendő lépések:
1. Állítsa be az időt, a dátumot és az időzónát.
2. Hamarosan megjelenik egy felugró ablak a képernyőn, amely arra
kéri, hogy változtassa meg a rendszer hitelesítési jelszavát. Kövesse a
képernyőn megjelenő lépéseket, vagy nyomja meg az NVR ESC gombját
a jelszóbeállítási felületről való kilépéshez .
Megjegyzés: A rendszer biztonsága érdekében javasoljuk a jelszó megváltoztatását
az első bejelentkezés után.
3. Állítsa be manuálisan a hálózati paramétereket, vagy aktiválja a DHCP
opciót az automatikus letöltéshez.
4. Olvassa be a képernyőn található QR-kódot az XMEye alkalmazás
mobiltelefonjára történő telepítéséhez. Olvassa be a QR-kódot a
sorozatszámmal, hogy hozzáadja a rendszert az alkalmazáshoz.
5. Állítsa be az NVR-hez csatlakoztatott monitor megjelenítési opcióit és
felbontását. Maximális támogatott felbontás: 2560x1440 (2K).
Megjegyzés: A felbontás módosítása előtt ellenőrizze, hogy a monitor támogatja-e
ezt a felbontást. Ha a beállított felbontás magasabb, mint a monitor felbontása,
akkor semmi nem jelenik meg a monitoron, és nem fog tudni hozzáférni a menühöz.
Ebben az esetben azonban csatlakoztassa az NVR-t alacsonyabb felbontású
monitorhoz, lépjen be a menübe és változtassa meg a felbontást.
6. Az alapkonfiguráció befejezéséhez nyomja meg az OK gombot.
Kattintson a jobb gombbal a képernyőn, és nyissa meg a NetDetect opciót.
Kattintson a Diagnózis elemre a hálózati konfiguráció teszteléséhez.
Megjegyzés: A beállítások életbe lépéséhez indítsa újra a rendszert. Kattintson a
jobb gombbal a képernyőn - Logout - Reboot.
Magyar
A rendszer számos szűrőt és lehetőséget kínál a kívánt rekord azonosítására.
Kereshet csatornaszám, dátum és időintervallum vagy fájltípus szerint.
Magyar
Opciók: General, Encode, Backup, Snapshot Config., Display, Account.
General (Tábornok)
Magyar
Állítsa be, hogy ciklikus felvételeket készítsen egy adott időpontban, és
e-mailben, FTP-ben küldje el, vagy tárolja a merevlemezen.
Display (Kijelző)
Account (Számla)
Magyar
Opciók: Intelligent Alert, Abnormality and Traditional alarm (Nincs kép,
nincs videojel stb.). A riasztás bevitele és az intelligens opciók nem állnak
rendelkezésre ennél a modellnél.
Set the system behavior in case of: storage device error, lack of space on the
storage device, lack of internet connection or IP conflict. In such situations you
can set to send a notification in the application or an email.
Magyar
Opciók: HDD info, Upgrade, AutoMaintain, Restore, Import / Export, Digital,
LOG, BPS és Version.
AutoMaintain
Restore (Visszaállítás)
Digitális csatornák
Magyar
Megjeleníti mind a 9 csatorna állapotát (csatlakoztatva, nem csatlakozva vagy
konfigurálatlanul).
Változat
Displays useful information about firmware and QR code with the system
serial number (useful for adding it to the mobile application) and QR code for
downloading the mobile application.
Magyar
Kattintson a jobb gombbal a
képernyőn a további lehetőségek
megjelenítéséhez:
Channel Set, Record Mode,
Playback, Face detection, IPC
parameters, Color settings, Split
menu, PTZ Control, Output adjust,
NetDetect, Logout.
Videokamerák hozzáadása
1. Válassza ki az NVR és a kamerák közötti kommunikációs protokollt.
Opciók: NETIP, ONVIF, Full Netcom.
2. Keresés. Nyomja meg a Keresés gombot az NVR-rel azonos útválasztóhoz
(ugyanahhoz a hálózathoz) csatlakoztatott kamerák kereséséhez.
3. Add hozzá. A megjelenített kamerák listájából válassza ki a kívánt
kamerákat, és kattintson a Hozzáadás gombra, hogy felvegye őket a
rendszerbe.
4. Hálózat. Konfigurálja a kamerák hálózati paramétereit (IP-cím, átjáró stb.)
5. Gyors beállítás. A kamerák gyors hozzáadása és konfigurálása.
6. IP tömeges módosítása. Gyors IP-váltás több kamerára.
Csatornák interfész
1. Törlés. Törölje a kamerát a kiválasztott csatornáról. A futtatáshoz kattintson
az Alkalmaz gombra.
2. Tiszta. Törölje a kiválasztott csatorna adatait. A futtatáshoz kattintson az
Alkalmaz gombra.
3. Kódolás. Megjeleníti a csatlakoztatott kamerák műszaki paramétereit
(felbontás, képkockasebesség, videotömörítés, minőség stb.).
149 Használati utasítás
4. Szerkessze az eszközöket. Változtassa meg a kiválasztott csatorna IP-címét
és portját.
Magyar
Playback (Lejátszás)
Split menu
Output Adjust
Magyar
1. Local Net Detect. Kamera csatlakozás figyelése és diagnosztika.
s
2. Remote Net Detect. A hálózat és a Cloud szerver figyelése, diagnosztikája
és konfigurálása.
Logout
Italiano
• Registrazione multicanale simultanea in tempo reale, riproduzione e
configurazione da remoto
• Supporta fino a 9 canali con una risoluzione massima di 4K (8MP).
• Backup su memoria flash USB e HDD esterno.
• Supporta il rilevamento di volti e forme umane (a seconda della telecamera)
• Possibilità di collegare altoparlante esterno
Specifiche tecniche
NVR
Ingressi video 4 x RJ45 POE
Uscita video 1 x VGA / 1 x HDMI
Uscita audio 1 x 3.5mm
Numero di canali 9 x max. 4K (8MP)
Risoluzione di massimo 2K (2560 x 1440) su uscita HDMI
riproduzione massimo 1080P (1920 x x1080) su uscita VGA
Ethernet 1 x RJ45 100/100Mbps
Compressione video H.265AI/H.265+
Compressione audio G.711A
Modalità di Manuale, allarme, rilevamento del movimento,
registrazione programmato
USB 2 x USB2.0
Disco fisso 1 x HDD SATA (max. 8Tb)
ONVIF Si
Tensione di 48V / 2A
alimentazione
Dimensioni 255 x 220 x 43 mm mm
Temperatura di lavoro -26°C ~ +80°C
Manuale, allarme, rilevamento del movimento, programmato
Risoluzione 3MP (2304 x 1296)
Lente 3.6mm
GUIDATO 4 IR LEDs and floodlight
155 Manuale dell’utente
Alimentazione POE
elettrica
Italiano
Dimensioni 70 x 190 x 65 mm
Temperatura di lavoro -26°C ~ +80°C
Accendere il dispositivo
Collegare il cavo di alimentazione a una presa da 230V. L’NVR si avvierà. Il
LED indicatore si accenderà.
Se l’ora di inizio rientra nella pianificazione preimpostata per la registrazione, la
funzione di registrazione si avvierà automaticamente.
Appunti:
1. Verificare che la tensione di ingresso corrisponda alla tensione consigliata del
dispositivo. La tensione di alimentazione è 230V ± 10% / 50 Hz 2A.
2. Si consiglia di utilizzare un dispositivo UPS per proteggere il dispositivo dalle
fluttuazioni di tensione.
Spegnere il dispositivo
Esistono due modi per spegnere il dispositivo.
1. Accedere al menu principale (clic destro sullo schermo) e selezionare l’opzione
Logout - Shutdown
2. Spegnere l’alimentazione.
Avvertenze speciali:
Italiano
ripristino dell’alimentazione.
2. Sostituire la batteria sulla scheda di sistema. Prima di sostituire la batteria,
è necessario eseguire il backup delle impostazioni di sistema (vedere il capitolo
Advanced-Import / Export) e disattivare l’alimentazione. L’ora e la data del
dispositivo devono essere reimpostate dopo la sostituzione della batteria. Si
consiglia di sostituire la batteria ogni anno.
Android iOS
Il file di installazione può
essere scaricato dal CD
incluso nella confezione
Windows General CMS
o dalla sezione Download
nella pagina web del
prodotto (www.pni.it)
Pasi da seguire:
1. Impostare l’ora, la data e il fuso orario.
2. Presto sullo schermo apparirà una finestra popup che ti chiederà di cambiare
la password di autenticazione nel sistema. Seguire i passaggi sullo schermo
o premere il tasto ESC sull’NVR per uscire dall’interfaccia di impostazione
della password.
Nota: per la sicurezza del tuo sistema, ti consigliamo di cambiare la password dopo
il primo accesso al sistema.
3. Impostare manualmente i parametri di rete o attivare l’opzione DHCP per
il download automatico.
4. Scansiona il codice QR sullo schermo per installare l’applicazione XMEye sul
tuo cellulare. Scansiona il codice QR con il numero di serie per aggiungere
il sistema all’applicazione.
5. Imposta le opzioni di visualizzazione e la risoluzione del monitor collegato
all’NVR. Risoluzione massima supportata 2560x1440 (2K).
Nota: prima di modificare la risoluzione, assicurati che il tuo monitor supporti
tale risoluzione. Se la risoluzione impostata è superiore alla risoluzione del tuo
monitor, non apparirà nulla sul monitor e non potrai accedere al menu. In tal caso,
tuttavia, collegare l’NVR a un monitor a risoluzione inferiore, accedere al menu e
modificare la risoluzione.
6. Premere il tasto OK per completare la configurazione di base del sistema.
7. Fare clic con il tasto destro sullo schermo e accedere all’opzione NetDetect.
Fare clic su Diagnostica per testare la configurazione di rete.
Nota: per rendere effettive le impostazioni, riavviare il sistema. Fare clic con il tasto
destro sullo schermo - Logout - Reboot.
Playback (Riproduzione)
Italiano
Network (Impostazioni di rete)
System (Sistema)
Opzioni: General, Encode, Backup, Snapshot Config., Display, Account.
General (Generale)
Display
Nella modalità di anteprima locale possono essere visualizzati: ora, nome del
canale, stato di registrazione, stato di allarme, trasparenza e risoluzione del
display.
Manuale dell’utente 164
Nota: prima di modificare la risoluzione, assicurati che il tuo monitor supporti tale
risoluzione. Se la risoluzione impostata è superiore alla risoluzione del tuo monitor,
Italiano
non apparirà nulla sul monitor e non potrai accedere al menu. In tal caso, tuttavia,
collegare l’NVR a un monitor a risoluzione inferiore, accedere al menu e modificare
la risoluzione.
Account (Conto)
Alarm (Allarme)
Opzioni: Intelligent Alert, Abnormality e Traditional alarm (Nessuna immagine,
nessun segnale video, ecc.). Le opzioni Ingresso allarme e Intelligente non sono
disponibili per questo modello.
Italiano
Abnormality (Situazione anomala)
Advanced (Avanzzato)
Opzioni: HDD info, Upgrade, AutoMaintain, Restore, Import / Export, Digital,
LOG, BPS e Version.
Italiano
Imposta il funzionamento del disco rigido (sola lettura o lettura-scrittura).
Nota: per salvare le registrazioni sul disco rigido, è necessario impostare la modalità
di lettura/scrittura.
Upgrade (Aggiornamento)
Restore (Repristino)
Import/Export (Importa/Esporta)
Aggiungi una telecamera su un canale specifico. Fare clic sul pulsante Aggiungi,
quindi su Cerca per trovare tutte le telecamere collegate alla stessa rete (stesso
router) con l’NVR.
171 Manuale dell’utente
Italiano
Version (Versione)
Italiano
4. Network. Configurare i parametri di rete per le telecamere (indirizzo IP,
gateway, ecc.)
5. Quick set. Aggiunta e configurazione rapida delle telecamere.
6. IP bulk modify. Cambio rapido di IP su più telecamere.
Interfaccia canali
1. Delete. Elimina la telecamera dal canale selezionato. Fare clic su Applica per
eseguire.
2. Clear. Elimina le informazioni sul canale selezionato. Fare clic su Applica per
eseguire.
3. Encode. Visualizza i parametri tecnici delle telecamere collegate (risoluzione,
frame rate, compressione video, qualità, ecc.).
4. Edit devices. Cambia IP e porta per il canale selezionato.
5. Bulk upgrade. Aggiornamento del firmware per le telecamere selezionate.
6. Network detect. Test e diagnostica di rete cloud e server.
7. Channel title. Rinomina le fotocamere.
8. NVR Network. Configura i parametri di rete dell’NVR.
9. Close adaptive. Disabilita la funzione di adattamento IP per le telecamere
selezionate.
Net Detect
Italiano
3. Net traffic Detect. Monitoraggio del traffico dati eseguito da NVR in rete.
Technische specificaties
NVR
Video-ingangen 4 x RJ45 POE
Video uitgang 1 x VGA / 1 x HDMI
Audio uitgang 1 x 3.5mm
Aantal kanalen 9 x max. 4K (8MP)
Maximaal 2K (2560 x 1440) op HDMI-uitgang
Afspeelresolutie
Maximaal 1080P (1920 x x1080) op VGA-uitgang
Ethernet 1 x RJ45 100/100Mbps
Video compressie H.265AI/H.265+
Audiocompressie G.711A
Handmatig, alarm, bewegingsdetectie,
Opnamemodus:
geprogrammeerd
USB 2 x USB2.0
HDD 1 x HDD SATA (max. 8Tb)
ONVIF Ja
Voedingsspanning: 48V / 2A
Dimensies 255 x 220 x 43 mm mm
Werktemperatuur -26°C ~ +80°C
Beveiligingscamera
Oplossing 3MP (2304 x 1296)
Lens 3.6mm
LED 4 IR LEDs and floodlight
Gebruikershandleiding 180
Stroomvoorziening POE
Nederlands
Dimensies 70 x 190 x 65 mm
Werktemperatuur -26°C ~ +80°C
Gebruiksaanwijzing
De opslagruimte installeren
Installeer de opslagruimte voor het eerste gebruik. Er kan slechts één SATA
HDD met een maximale capaciteit van 14TB in de opname-eenheid worden
geïnstalleerd (HDD is niet inbegrepen in het pakket).
• Draai de schroeven los en open de NVR-behuizing
• Sluit de datakabels aan en zet de harde schijf vast met de schroeven
• Sluit de NVR-behuizing terug
• Sluit de stroom- en internetkabel aan op de NVR
181 Gebruikershandleiding
Speciale waarschuwingen:
1. Herstart na stroomuitval. Als het apparaat abnormaal wordt gesloten, maakt
Nederlands
het een back-up en start het opnieuw vanaf die status nadat de stroom is
hersteld.
2. Plaats de batterij terug op het moederbord. Voordat u de batterij vervangt,
moet u een back-up van uw systeeminstellingen maken (zie hoofdstuk
Geavanceerd importeren / exporteren) en de stroomtoevoer uitschakelen. De
tijd en datum van het apparaat moeten opnieuw worden ingesteld nadat de
batterij is vervangen. We raden aan om de batterij elk jaar te vervangen.
Android iOS
Het installatiebestand
kan worden
gedownload vanaf de
cd die is meegeleverd
Windows General CMS
in het pakket of via de
downloadsectie op de
productwebpagina (www.
MyPNI.nl)
Systeemverificatie
Nadat u het apparaat hebt ingeschakeld, logt u in op het systeem.
Standaard is de admin-gebruiker beveiligd met een wachtwoord door 1234.
Als het wachtwoord 5 keer achter elkaar verkeerd wordt ingevoerd, wordt het
Gebruikershandleiding 182
account geblokkeerd. Door het apparaat opnieuw op te starten of na een half
uur wordt het account automatisch ontgrendeld.
Nederlands
Opmerking: Voor de veiligheid van uw systeem dient u het wachtwoord na de
eerste keer inloggen te wijzigen.
Snelle installatiegids
Nadat het apparaat is gestart, wordt de beknopte installatiehandleiding gestart.
Opmerking: we raden aan het systeem te configureren voordat u de NVR en
camera’s op de uiteindelijke locatie installeert.
Te volgen stappen:
1. Stel de tijd, datum en tijdzone in.
2. Binnenkort verschijnt er een pop-upvenster op het scherm waarin u wordt
gevraagd het authenticatiewachtwoord in het systeem te wijzigen. Volg
de stappen op het scherm of druk op de ESC-toets op de NVR om de
interface voor het instellen van het wachtwoord te verlaten.
Opmerking: voor de veiligheid van uw systeem raden we aan het wachtwoord te
wijzigen na de eerste keer inloggen in het systeem.
3. Stel de netwerkparameters handmatig in of activeer de DHCP-optie voor
automatisch downloaden.
4. Scan de QR-code op het scherm om de XMEye-applicatie op uw mobiele
telefoon te installeren. Scan de QR-code met het serienummer om het
systeem aan de applicatie toe te voegen.
5. Stel de weergaveopties en resolutie in van de monitor die is aangesloten op
de NVR. Maximaal ondersteunde resolutie 2560x1440 (2K).
Opmerking: Voordat u de resolutie wijzigt, moet u ervoor zorgen dat uw monitor
die resolutie ondersteunt. Als de ingestelde resolutie hoger is dan de resolutie van
uw monitor, verschijnt er niets op de monitor en kunt u het menu niet openen. Als
dit echter gebeurt, sluit u de NVR aan op een monitor met een lagere resolutie,
opent u het menu en wijzigt u de resolutie.
6. Druk op de OK-toets om de basissysteemconfiguratie te voltooien.
7. Klik met de rechtermuisknop op het scherm en open de NetDetect-optie.
Klik op Diagnose om de netwerkconfiguratie te testen.
Opmerking: Start het systeem opnieuw op om de instellingen van kracht te laten
worden. Klik met de rechtermuisknop op het scherm - Logout - Reboot.
183 Gebruikershandleiding
Nederlands
Het menu
Klik in de hoofdvoorbeeldinterface
met de rechtermuisknop om het
menu te openen.
Gebruikershandleiding 184
Nederlands
Playback (Afspelen)
Het systeem biedt tal van filters en mogelijkheden om het gewenste record te
identificeren. U kunt zoeken op kanaalnummer, datum en tijdsinterval of op
bestandstype.
185 Gebruikershandleiding
en alarm).
Nederlands
Network (Netwerk)
General (Algemeen)
Encode
Backup
Nederlands
Snapshot Config (Momentopnameconfiguratie)
Display
monitor, verschijnt er niets op de monitor en kunt u het menu niet openen. Als dit
echter gebeurt, sluit u de NVR aan op een monitor met een lagere resolutie, opent
u het menu en wijzigt u de resolutie.
Account (Rekening)
Met de interface kunnen gebruikers die toegang hebben tot het systeem
beheren, gebruikers toevoegen, gebruikersrechten wijzigen, het wachtwoord
wijzigen, gebruikersgroepen maken en een accountbeveiligingsniveau instellen
door antwoorden op bepaalde vooraf gedefinieerde vragen te registreren. In
geval van wachtwoord reset kan de verificatiecode worden verzonden in de
mobiele applicatie of op het ingestelde e-mailadres. Om de beveiliging te
vergroten, kunt u een patroon instellen voor toegang tot het systeem.
Gebruikershandleiding 190
Nederlands
Alarm (Alarm)
Opties: Intelligent Alert, Abnormality en Traditional alarm (Geen beeld, Geen
videosignaal, enz.). Alarmingang en intelligente opties zijn niet beschikbaar
voor dit model.
191 Gebruikershandleiding
in.
Nederlands
Abnormality (Afwijking)
Nederlands
Advanced (Geavanceerd)
Opties: HDD info, Upgrade, AutoMaintain, Restore, Import / Export, Digital,
LOG, BPS en Version.
HDD info
193 Gebruikershandleiding
schrijfmodus staan.
Nederlands
Upgrade
Nederlands
Restore (Resetten)
Import/Export (Importeren/Exporteren)
195 Gebruikershandleiding
Nederlands
Digital (Digitaal)
Voeg een camera toe aan een specifiek kanaal. Klik op de knop Toevoegen
en vervolgens op Zoeken om alle camera’s te vinden die op hetzelfde netwerk
(dezelfde router) zijn aangesloten met de NVR.
Gebruikershandleiding 196
Nederlands
Channel status (Kanaalstatus)
197 Gebruikershandleiding
(8MP).
Nederlands
Log (Logboek)
Geeft de geschiedenis weer van acties die in het systeem zijn uitgevoerd.
Version (Versie)
Geeft nuttige informatie weer over firmware en QR-code met het serienummer
van het systeem (handig om het toe te voegen aan de mobiele applicatie) en
QR-code om de mobiele applicatie te downloaden.
Gebruikershandleiding 198
Nederlands
Andere menu-opties
Klik met de rechtermuisknop op
het scherm om extra opties weer te
geven:
Channel Set, Record Mode,
Playback, Face detection, IPC
parameters, Color settings, Split
menu, PTZ Control, Output adjust,
NetDetect, Logout.
Met de interface kunnen de camera’s die aan het systeem zijn toegevoegd,
worden toegevoegd en beheerd.
Camera-interface toevoegen
1. Selecteer het communicatieprotocol tussen de NVR en de camera’s. Opties:
NETIP, ONVIF, Full Netcom.
2. Search. Druk op de zoektoets om te zoeken naar camera’s die zijn aangesloten
199 Gebruikershandleiding
op dezelfde router (hetzelfde netwerk) als de NVR.
3. Add. Selecteer in de lijst met weergegeven camera’s de gewenste camera’s
Nederlands
Kanalen interface
1. Delete. Verwijder de camera van het geselecteerde kanaal. Klik op Toepassen
om te starten.
2. Clear. Verwijder de informatie over het geselecteerde kanaal. Klik op
Toepassen om te starten.
3. Encode. Toont de technische parameters van de aangesloten camera’s
(resolutie, framerate, videocompressie, kwaliteit, enz.).
4. Edit devices. Wijzig IP en poort voor het geselecteerde kanaal.
5. Bulk upgrade. Firmware-update voor geselecteerde camera’s.
6. Network detect. Testen en diagnostiek van cloudnetwerken en servers.
7. Channel title. Camera’s hernoemen.
8. NVR Network. NVR-netwerkparameters configureren.
9. Close adaptive. Schakelt de IP-aanpassingsfunctie uit voor de geselecteerde
camera’s.
Gebruikershandleiding 200
Nederlands
201 Gebruikershandleiding
Nederlands
Preview (Voorbeeld)
Gebruikershandleiding 202
Selecteer hoe de camera’s op hetzelfde scherm moeten worden weergegeven.
Nederlands
Output Adjust
Net Detect
s
2. Remote Net Detect. Monitoring, diagnose en configuratie van netwerk en
cloudserver.
203 Gebruikershandleiding
Nederlands
Gebruikershandleiding 204
Główne funkcje
Polskie
• Jednoczesne nagrywanie wielokanałowe w czasie rzeczywistym, zdalne
odtwarzanie i konfiguracja
• Obsługuje do 9 kanałów o maksymalnej rozdzielczości 4K (8MP).
• Kopia zapasowa na pamięci flash USB i zewnętrznym dysku twardym.
• Obsługuje wykrywanie twarzy i kształtu ludzkiego (w zależności od aparatu)
• Możliwość podłączenia zewnętrznego głośnika.
Specyfikacja techniczna
NVR
Wejścia wideo 4 x RJ45 POE
Wyjście wideo 1 x VGA / 1 x HDMI
Wyjście audio 1 x 3.5mm
Liczba kanałów 9 x max. 4K (8MP)
Rozdzielczość Maks. 2K (2560 x 1440) na wyjściu HDMI
odtwarzania Maks. 1080P (1920 x 1080) na wyjściu VGA
Ethernet 1 x RJ45 100/100Mbps
Kompresja wideo H.265AI/H.265+
Kompresja dźwięku G.711A
Tryb nagrywania Ręczny, alarm, detekcja ruchu, zaprogramowany
USB 2 x USB2.0
dysk twardy 1 x HDD SATA (max. 8Tb)
ONVIF YTakes
Napięcie 48V / 2A
Wymiary 255 x 220 x 43 mm mm
Temperatura pracy -26°C ~ +80°C
Kamera
Rezolucja 3MP (2304 x 1296)
Obiektyw 3.6mm
PROWADZONY 4 diody IR i reflektor
Zasilacz POE
Instrukcja użycia
Instalowanie jednostki do przechowywania
Włącz urządzenie
Podłącz przewód zasilający do gniazdka 230V. NVR zostanie uruchomiony.
Zaświeci się wskaźnik LED. Domyślnie na ekranie będzie wyświetlanych 9
kanałów.
Jeśli czas rozpoczęcia mieści się w ustalonym harmonogramie nagrywania,
funkcja nagrywania rozpocznie się automatycznie.
Uwagi:
1. Sprawdź, czy napięcie wejściowe odpowiada zalecanemu napięciu urządzenia.
Napięcie zasilania wynosi 230V ± 10% / 50 Hz 2A.
2. Sugerujemy użycie zasilacza UPS w celu ochrony urządzenia przed wahaniami
napięcia.
Wyłącz urządzenie
Urządzenie można wyłączyć na dwa sposoby.
1. Wejdź do menu głównego (kliknij prawym przyciskiem myszy na ekranie) i
wybierz opcję Wyloguj - Zamknij
2. Wyłącz zasilanie.
Specjalne ostrzeżenia:
1. Uruchom ponownie po awarii zasilania. Jeśli urządzenie zostanie nieprawidłowo
Instrukcja obsługi 206
zamknięte, tworzy kopię zapasową i uruchamia się ponownie od tego stanu po
przywróceniu zasilania.
Polskie
2. Wymień baterię na płycie systemowej. Przed wymianą baterii należy wykonać
kopię zapasową ustawień systemowych (patrz rozdział Zaawansowane-Import
/ Eksport) i wyłączyć zasilanie. Po wymianie baterii należy ponownie ustawić
godzinę i datę urządzenia. Zalecamy wymianę baterii co roku.
Android iOS
Plik instalacyjny można
pobrać z płyty CD
dołączonej do pakietu
Windows General CMS
lub z sekcji Download na
stronie produktu (www.
pni.pl)
Uwierzytelnianie systemu
Po włączeniu urządzenia zaloguj się do systemu.
Domyślnie administrator jest chroniony hasłem 1234. Jeśli hasło zostanie
wprowadzone niepoprawnie 5 razy z rzędu, konto zostanie zablokowane.
Po ponownym uruchomieniu urządzenia lub po pół godzinie konto zostanie
odblokowane automatycznie.
Ręcznie ustaw parametry sieciowe (adres IP, brama, DNS, port itp.) lub zaznacz
opcję DHCP w celu automatycznego pobierania parametrów.
Uwaga: aby ustawienia zaczęły obowiązywać, uruchom ponownie system. Kliknij
prawym przyciskiem myszy na ekranie - Logout - Reboot.
System
Opcje: General, Encode, Backup, Snapshot Config., Display, Account.
General (Ogólny)
Backup
Pamięć USB lub zewnętrzny dysk twardy musi być zainstalowany w NVR
przed rozpoczęciem tworzenia kopii zapasowej. Naciśnij przycisk Wykryj, aby
zidentyfikować urządzenie pamięci, a następnie przycisk Kopia zapasowa, aby
Display (Wyświetlacz)
W trybie podglądu lokalnego mogą być wyświetlane: czas, nazwa kanału, stan
nagrywania, stan alarmów, przezroczystość i rozdzielczość wyświetlania.
Uwaga: przed zmianą rozdzielczości upewnij się, że monitor obsługuje tę rozdzielczość.
Instrukcja obsługi 214
Jeśli ustawiona rozdzielczość jest wyższa niż rozdzielczość monitora, nic nie pojawi
się na monitorze i nie będzie można uzyskać dostępu do menu. Jeśli jednak tak się
Polskie
stanie, podłącz NVR do monitora o niższej rozdzielczości, wejdź do menu i zmień
rozdzielczość.
Account (Konto)
Alarm
Opcje: Intelligent Alert, Abnormality oraz Traditional alarm (Brak obrazu, brak
sygnału wideo itp.). Wejście alarmowe i opcje inteligentne nie są dostępne w
tym modelu.
Polskie
Abnormality (Nieprawidłowość)
Ustaw zachowanie systemu w przypadku braku obrazu lub braku sygnału wideo.
W takich sytuacjach można ustawić wysłanie powiadomienia w aplikacji lub
217 Instrukcja obsługi
e-mail, rozpoczęcie nagrywania, wykonanie przechwytywania lub zapisanie
nagrania alarmowego na serwerze FTP.
Polskie
Advanced (Zaawansowany)
Opcje: HDD info, Upgrade, AutoMaintain, Restore, Import / Export, Digital,
LOG, BPS oraz Version.
Polskie
Upgrade
Włóż pamięć USB do NVR, która powinna zawierać plik aktualizacji w folderze
głównym. Wybierz dysk i plik z menu NVR i kliknij przycisk Aktualizuj.
AutoMaintain (Autokonserwacja)
Ustaw system, aby uruchamiał się w określonym dniu i godzinie lub ustaw
219 Instrukcja obsługi
automatyczne usuwanie plików starszych niż określony okres.
Polskie
Restore (Resetowanie)
Import Eksport
Kanały cyfrowe
Stan kanału
Polskie
Log (Dziennik)
Version (Wersja)
Zestaw kanałów
Polskie
3. Add. Z listy wybierz wybierz system wybierz system i kliknij Dodaj, aby
dodać do systemu.
4. Network. Skonfiguruj parametry sieciowe dla kamer (adres IP, brama itp.)
5. Quick set.Szybkie dodawanie i konfiguracja kamer.
6. IP Bulk Modify. Szybka zmiana IP na wiele kamer.
Interfejs kanałów
1. Delete. Usuń kamerę z wybranego kanału. Kliknij Zastosuj, aby uruchomić.
2. Clear. Usuń informacje o wybranym kanale. Kliknij Zastosuj, aby uruchomić.
3. Encode. Wyświetla parametry techniczne podłączonych kamer (rozdzielczość,
liczba klatek na sekundę, kompresja wideo, jakość itp.).
4. Edit devices. Zmień IP i port dla wybranego kanału.
5. Bulk upgrade. Aktualizacja oprogramowania dla wybranych kamer.
6. Network detect. Testowanie i diagnostyka sieci i serwerów w chmurze.
7. Channel title. Zmień nazwy kamer.
8. NVR Network. Skonfiguruj parametry sieci NVR.
9. Close adaptive. Wyłącza funkcję adaptacji IP dla wybranych kamer.
Output Adjust
Net Detect
Polskie
3. Net traffic Detect. Monitorowanie ruchu danych realizowanego przez NVR
w sieci.
Specificatii tehnice
NVR
Intrari video 4 x RJ45 POE
Iesiri video 1 x VGA / 1 x HDMI
Iesire audio 1 x 3.5mm
Numar canale 9 x max. 4K (8MP)
Maxim 2K (2560 x 1440) pe iesirea HDMI
Rezolutie de redare
Maxim 1080P (1920 x x1080) pe iesirea VGA
Ethernet 1 x RJ45 100/100Mbps
Compresie video H.265AI/H.265+
Compresie audio G.711A
Mod inregistrare Manual, alarma, detectie miscare, programat
USB 2 x USB2.0
HDD 1 x HDD SATA (maxim 8Tb)
ONVIF Da
Alimentare 48V / 2A
Dimensiuni 255 x 220 x 43 mm mm
Temperatura de lucru -26°C ~ +80°C
Camera
Rezolutie 3MP (2304 x 1296)
Lentila 3.6mm
LED-uri 4 LED-uri IR si floodlight
Alimentare POE
Romana
Instructiuni de utilizare
Pornirea dispozitivului
Introduceti cablul de alimentare intr-o priza 230V. NVR-ul va porni. LED-ul
indicator se va aprinde.
Daca ora de pornire se incadreaza in programul presetat pentru inregistrare,
atunci functia de inregistrare va porni automat.
Note.
1. Verificati daca tensiunea de intrare corespunde cu tensiunea recomandata a
dispozitivului. Tensiunea de alimentare este de 230V±10% / 50 Hz 2A.
2. Va sugeram sa folositi un dispozitiv UPS pentru a proteja dispozitivul de variatiile
de tensiune.
Oprirea dispozitivului
Sunt doua metode de oprire a dispozitivului.
1. Accesati meniul principal (click dreapta pe ecran) si selectati optiunea Logout
- Shutdown (Inchidere)
2. Opriti sursa de alimentare.
Atentionari speciale:
1. Repornirea dupa caderea tensiunii. Daca dispozitivul este inchis anormal,
231 Manual de utilizare
acesta creeaza o copie de siguranta si reporneste de la acel status dupa revenirea
alimentarii.
Romana
Android iOS
Fisierul de instalare poate
fi descarcat de pe CD-
ul inclus in pachet sau
Windows General CMS
din sectiunea Download
de pe pagina web a
produsului (www.pni.ro)
Autentificarea in sistem
Dupa pornirea dispozitivului, autentificati-va in sistem.
Implicit, utilizatorul admin este protejat de parola 1234. Daca parola este
introdusa gresit de 5 ori la rand, contul va fi blocat. Prin repornirea dispozitivului
sau dupa o jumatate de ora, contul va fi deblocat automat.
Nota: Pentru securitatea sistemului Dvs. va rugam sa modificati parola dupa prima
autentificare.
Romana
Dupa pornirea dispozitivului va porni ghidul de configurare rapida.
Nota: Recomandam configurarea sistemului inainte de instalarea NVR-ului si a
camerelor in locatia finala.
Pasii de urmat:
1. Setati ora, data si fusul orar.
2. In scurt timp, pe ecran va aparea un popup prin care vi se cere sa schimbati
parola de autentificare in sistem. Urmati pasii de pe ecran sau apasati tasta
ESC de pe NVR pentru a iesi din interfata de setare a parolei.
Nota: Pentru siguranta sistemului Dvs., recomandam schimbarea parolei dupa
prima autentificare in sistem.
3. Setati parametrii de retea manual sau activati optiunea DHCP pentru
preluarea automata a acestora.
4. Scanati codul QR de pe ecran pentru a instalata aplicatia XMEye in
telefonul Dvs. mobil. Scanati codul QR cu numarul de serie pentru
adaugarea sistemului in aplicatie.
5. Setati optiunile de afisare si rezolutia monitorului conectat la NVR.
Rezolutie maxima suportata 2560x1440(2K).
Nota: Inainte de a modifica rezolutia, asigurati-va ca monitorul Dvs. suporta
rezolutia respectiva. Daca rezolutia setata este mai mare decat rezolutia monitorului
Dvs., pe monitor nu va aparea nimic si nu veti mai putea accesa meniul. Daca se
intampla, totusi, acest lucru, conectati NVR-ul la un monitor cu o rezolutie mai
mare, accesati meniul si schimbati rezolutia.
6. Apasati tasta OK pentru a finaliza configurarea de baza a sistemului.
7. Faceti click dreapta pe ecran si accesati optiunea NetDetect. Faceti click
pe Diagnose pentru a testa configurarea retelei.
Nota: Pentru ca setarile sa aiba efect, restartati sistemul. Click dreapta pe ecran -
Logout - Reboot.
Meniul
In interfata principala de previzualizare
faceti click dreapta cu mouse-ul
pentru a accesa meniul.
Romana
Sistemul va ofera numeroase filtre si optiuni pentru identificarea inregistrarii
dorite. Puteti cauta dupa numarul canalului, data si intervalul orar sau dupa
tipul fisierului.
Setati manual parametrii de retea (adresa IP, gateway, DNS, port etc.) sau
bifati optiunea DHCP pentru preluarea automata a parametrilor.
Nota: Pentru ca setarile sa aiba efect, restartati sistemul. Click dreapta pe ecran -
Logout - Reboot.
Romana
Optiuni: General, Encode, Backup, Snapshot Config. (Configurare capturi
imagine), Display (Afisare), Account (Cont).
General
Memoria USB sau HDD-ul extern trebuie sa fie instalat in NVR inainte de a
porni executia copiei de rezerva. Apasati butonul Detect pentru identificarea
dispozitivului de stocare, apoi butonul Backup pentru executarea copiei de
rezerva.
Romana
Setati realizarea de capturi ciclic la un anumit interval de timp si trimiterea
acestora pe email, FTP sau stocarea acestora pe hard disk.
Display (Afisare)
Account (Cont)
Romana
Optiuni: Intelligent Alert (Alerta inteligenta), Abnormality (Comportament
anormal) si Traditional alarm (Lipsa imagine, Lipsa semnal video etc. ). Optiunile
Alarm input si Intelligent nu sunt disponibile pentru acest model.
Romana
Optiuni: HDD info, Upgrade, AutoMaintain (mentenanta automata), Restore
(Reset), Import/Export, Digital, LOG, BPS si Version (Versiune).
Romana
Afiseaza statusul (conectat, neconectat sau neconfigurat) pentru toate cele 9
canale.
Romana
Click dreapta pe ecran pentru a afisa
optiunile suplimentare:
Channel Set, Record Mode,
Playback, Face detection, IPC
parameters, Color settings, Split
menu, PTZ Control, Output adjust,
NetDetect, Logout.
Channel set
Interfata este disponibila doar pentru camerele care suporta aceasta functie.
Net Detect
Manual de utilizare 252
1. Local Net Detect. Monitorizare si diagnosticare conexiune camere.
Romana
2. Remote Net Detect. Monitorizare, diagnosticare si configurare retea si
server Cloud.
Logout