Scribd Logo
Upload

Welcome to Scribd!

  • 59 views

    Crosby Model Pl-N/O Hook Latch Kit: Warning Warnings and Application Instructions

    Uploaded by

    Mareg Engenharia de Segurança

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Crosby Model Pl-N/O Hook Latch Kit: Warning Warnings and Application Instructions

    Uploaded by

    Mareg Engenharia de Segurança
    59 views1 page

    Original Title

    150

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    59 views1 page

    Crosby Model Pl-N/O Hook Latch Kit: Warning Warnings and Application Instructions

    Uploaded by

    Mareg Engenharia de Segurança

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    CROSBY MODEL PL-N/O WARNING

    HOOK LATCH KIT • Loads may disengage from hook if proper procedures are
    not followed.
    WARNINGS AND APPLICATION • A falling load may cause serious injury or death.
    INSTRUCTIONS • See OSHA Rule 1926.1431(g)(1)(i)(A) and 1926.1501(g)(4)(iv)(B)
    for Personnel Hoisting by Crane or Derricks. A Crosby or
    McKissick Hook with a Positive Locked PL-N/O or S-4320
    Latch may be used to Lift Personnel.
    • Hook must always support the load. The load must never
    be supported by the latch.
    • DO NOT use this latch in applications requiring non-
    sparking.
    • Read and understand these instructions before using hook
    and latch.

    RIGHT WRONG

    Model PL-N/O

    Important Safety Information -


    Read and Follow
    • Always inspect hook and latch before using. Figure 1 Figure 2
    • Never use a latch that is distorted or bent.
    • Always make sure spring will force the latch against the
    tip of the hook. RIGHT WRONG
    • Always make sure hook supports the load. The latch
    must never support the load. (See Figure 1 & 2.)
    • When placing two (2) sling legs in hook, make sure the
    angle between the legs is less than 90° and if the hook
    or load is tilted, nothing bears against the bottom of this
    latch. (See Figure 3 & 4.)
    • Latches are intended to retain loose sling or devices
    under slack conditions.
    Figure 3 Figure 4
    • Latches are not intended to be an anti-fouling device.

    IMPORTANT - Instructions for Assembling Model PL-N/O Latch


    on Crosby or McKissick Hooks

    Step 1 Step 2 Step 3 4, 5, & 6 Step 7,8 - For Step 9 - For


    1. Place hook in upright 2. Slip the latch over 3. Slide latch housing Personnel Lifting Personnel Lifting
    position. Position coils the spring until the two up the spring legs until 7. Rigging should 9. Rotate toggle 90
    of spring over cam with spring legs are posi- latch clears hook tip. be resting in bowl of degrees to secure
    legs of spring pointing tioned into the grooves 4. Resting latch on hook, with latch in pin (ensure toggle is
    toward tip of hook, located on the inside interlocking hook tip, closed position and in closed position as
    and loop of spring of the latch housing line up holes in latch gate locked. shown).
    positioned down and (legs of spring should fit with hook cam. 8. Insert toggle lock
    lying against the hook. between the gate and 5. Insert bolt through pin through hole and
    the housing). latch spring & cam. depress spring until
    6. Tighten self-locking toggle clears hole on
    nut on one end of bolt. other side of latch.

    rev. 3
    150 Copyright © 2013 The Crosby Group LLC
    All Rights Reserved

    You might also like