Scribd
Upload
45 views2 pages

Fanuc General Numeric 6 9

The document provides instructions for setting up DNC (Direct Numerical Control) communication between a Fanuc control system and a PC. It includes: 1) parameters to configure the Fanuc control and PC port settings, 2) transmit and receive settings for the DNC software, and 3) wiring diagrams for null modem or full handshake cable connections between the 9-pin or 25-pin ports.

Uploaded by

jj11459
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
45 views2 pages

Fanuc General Numeric 6 9

The document provides instructions for setting up DNC (Direct Numerical Control) communication between a Fanuc control system and a PC. It includes: 1) parameters to configure the Fanuc control and PC port settings, 2) transmit and receive settings for the DNC software, and 3) wiring diagrams for null modem or full handshake cable connections between the 9-pin or 25-pin ports.

Uploaded by

jj11459
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Fanuc and General Numeric 6 and 9 Series Controls

Set the following parameters on the machine

Parameter 311 = Baud Rate(4800)


Parameter 340 = 2 Input Device
Parameter 341 = 2 Output Device
I/O =1
ISO Format =1

Set the following parameters on the PC

General settings

Machine name MCH-1


Control system Fanuc 3
Machine ID 01
Time out (sec) 5
Control program start M82
Control program end M30
Is DNC required Yes

DNC settings

Port Number COM2 (or any free COM port)


Baud rate 4800
Data bits 7
Parity Even
Stop bits 2
Handshake Software
Filter null characters Yes

Transmit settings

Transmit directory Specify folder to store programs to be sent to machine from PC


Wait period at start of transmission 10.0
Wait period after transmitting program 5.0
Size of transmit packet 0
Delay period after each packet 0
Wait for XON before transmitting program No
Drip feed Off
Transmit comments? Yes
Comment start character (
Comment end character )
Translation mode for CR Transmit as CR
Translation mode for LF Transmit as LF
Program start string
Program end string
Filter Null character Yes
Character to transmit at start 0
Number of characters 0
Character to transmit at end 0
Number of characters 0

Receive settings

Receive directory Specify folder to store programs coming from machine


Wait period before receiving program 45.0
Wait period after receiving program 5.0
Transmit XON before transmitting program No
Auto compare and save Yes
Acknowledgements and errors Transmit descriptive messages
Translation mode for CR Ignore
Translation mode for LF Save as CRLF
Acknowledgement / Error message start
%

M30
Acknowledgement / Error message end
%
Ignore control characters other than CR-LF Yes

Cable connection
If the PC has 9 pin connector

Null modem Full Handshake


PC CNC PC CNC
9 pin 25 pin 9 pin 25 pin

1 8 1 8
2 2 2 2
3 3 3 3
4 20 4 6
5 7 5 7
6 6 6 20
7 4 7 5
8 5 8 4

If the PC has 25 pin connector

Null modem Full Handshake


PC CNC PC CNC
25 pin 25 pin 25 pin 25 pin

8 8 8 8
2 3 2 3
3 2 3 2
20 20 20 6
7 7 7 7
6 6 6 20
4 4 4 5
5 5 5 4

You might also like