0% found this document useful (0 votes)
455 views3 pages

Fanuc 10t

This document provides parameters and settings for connecting a Fanuc 10T CNC machine to a PC for DNC (Direct Numerical Control) programming. It includes parameter values to configure the CNC machine and PC as well as cable connection diagrams for null modem or full handshake connections between a PC with either a 9-pin or 25-pin serial port and the CNC machine's 25-pin serial port.

Uploaded by

jj11459
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
455 views3 pages

Fanuc 10t

This document provides parameters and settings for connecting a Fanuc 10T CNC machine to a PC for DNC (Direct Numerical Control) programming. It includes parameter values to configure the CNC machine and PC as well as cable connection diagrams for null modem or full handshake connections between a PC with either a 9-pin or 25-pin serial port and the CNC machine's 25-pin serial port.

Uploaded by

jj11459
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Fanuc 10 T

Set the following parameters on the machine

Parameter No. Value Parameter No. Value


5001 1 5120 4
5002 2 5121 2
5003 3 5122 9
5110 4 5130 4
5111 2 5131 2
5112 9 5132 9

Setting data

TV CHECK =0 (0:Off; 1:On)


Punch code =0 (0:ISO; 1:EIA)
Input device =1 (1 ~3:RS232C; 10:RMFBUF; 13:RS422)
Output device =1 (1 ~3:RS232C; 10:RMFBUF; 13:RS422)

Parameters for the various baud rates

For baud rates other than 2400 set the parameter 5112, 5122, 5132 as follows

Baud rate Parameter


50 1
100 2
110 3
150 4
200 5
300 6
600 7
1200 8
2400 9
4800 10
9600 11

Set the following parameters on the PC

General settings

Machine name MCH-1


Control system Fanuc
Machine ID 01
Time out (sec) 5
Control program start M82
Control program end M30
Is DNC required Yes

DNC settings

Port Number COM2 (or any free COM port)


Baud rate 2400
Data bits 7
Parity Even
Stop bits 2
Handshake Hardware
Filter null characters Yes
Transmit settings

Transmit directory Specify folder to store programs to be sent to machine from PC


Wait period at start of transmission 10.0
Wait period after transmitting program 5.0
Size of transmit packet 0
Delay period after each packet 0
Wait for XON before transmitting program No
Drip feed Off
Transmit comments? Yes
Comment start character (
Comment end character )
Translation mode for CR Transmit as CR
Translation mode for LF Transmit as LF
Program start string
Program end string

Receive settings

Receive directory Specify folder to store programs coming from machine


Wait period before receiving program 45.0
Wait period after receiving program 5.0
Transmit XON before transmitting program No
Auto compare and save Yes
Acknowledgements and errors Transmit descriptive messages
Translation mode for CR Ignore
Translation mode for LF Save as CRLF
%
Acknowledgement /error message start
O1234
M30
Acknowledgement /error message start
%
Ignore control characters other than CR-LF Yes

Cable connection
If the PC has 9 pin connector

Null modem Full Handshake


PC CNC PC CNC
9 pin 25 pin 9 pin 25 pin

1 8 1 8
2 2 2 2
3 3 3 3
4 20 4 6
5 7 5 7
6 6 6 20
7 4 7 5
8 5 8 4
If the PC has 25 pin connector

Null modem Full Handshake


PC CNC PC CNC
25 pin 25 pin 25 pin 25 pin

8 8 8 8
2 3 2 3
3 2 3 2
20 20 20 6
7 7 7 7
6 6 6 20
4 4 4 5
5 5 5 4

You might also like