Carbon

Dioxide
Extinguishing
System
AN INTRODUCTION TO NAFFCO
NAFFCO was founded in Dubai, UAE to become the world’s NAFFCO manufactures UL, FM, BSI & Global Mark approved
leading producer and supplier of life safety solutions. By products in our facility in consistent with International
recognizing the importance and convenience of having Standards” UL-DQS, BSI certifies for the Quality
easy access to multiple safety services, we became Management System against ISO 9001. Our Environmental
specialized by offering complete solutions under one (ISO 14001) & Occupational Health & Safety (OHSAS 18001)
roof for all types of high quality firefighting equipment, fire Management Systems have been certified by UL-DQS. Our
protection systems, fire alarms, addressable emergency Trucks & Vehicles division has been assessed & certified
systems, security systems,custom-made vehicles such as for Quality Management System requirement for Aviation,
fire trucks, ambulances, mobile hospitals and airport rescue Space & Defense organization(AS 9100) by UL-DQS.
firefighting vehicles (ARFF).
Our success is driven by our passion to protect; our vision
With the most talented and dedicated employees from is to become the world’s number one provider of innovative
around the world, NAFFCO has over 500 passionate solutions in protecting life, environment and property.
engineers and over 5 million square feet of manufacturing
facilities. We are currently exporting to over 100 countries
worldwide.

2 www.naffco.com
CARBON DIOXIDE EXTINGUISHING SYSTEM
DESCRIPTION:
NAFFCO Carbon Dioxide extinguishing system is designed in such as Paint Locker, Purifier Room, Galley Exhaust Duct etc. The
accordance to NFPA 12 and listed by UL. It is engineered for total number of CO₂ cylinders is calculated according to the size of the
flooding with the protection of machinery spaces, pump rooms largest protected area. Smoke Detection System can also include
and cargo holds and with a local protection of smaller spaces in the CO₂ System.

The CO₂ fire suppression system shall be activated by At the same time, alarm is activated to warn personnel in the area.
pneumatically / manually. When the master CO₂ cylinder activated, CO₂ gas is discharged into the space with the designed duration.
the slave CO₂ cylinders also activated without any time delay.

ADVANTAGES:
• Density is 1.5 times higher than air so it displaces air. • No residues left after application
• Non Corrosive • No deterioration with age.
• Electrically Non-conductor • It can be liquefied and bottled.

www.naffco.com 3
 TYPICAL CARBON DIOXIDE EXTINGUISHING SYSTEM LAYOUT

System Components:
1. Master Cylinder 10. Manifold
2. Slave Cylinders 11. Pilot Hose
3. Cylinder Label 12. Pressure Switch
4. Cylinder Mounting Brackets 13. Discharge Nozzle
5. Head Valve (Master Cylinder) 14. Smoke Detector
6. Head Valve (Slave Cylinder) 15. Alarm
7. Discharge Hose 16. Manual Call Point
8. Check Valve 17. Control Panel
9. Manifold Pressure Release

4 www.naffco.com
CYLINDER /VALVE ASSEMBLY
NAFFCO CO₂ cylinders shall be High Pressure Seamless Cylinder
available in different capacities (30 & 45kg.)

SPECIFICATION
Model NCS30 NCS45
Capacity 30kg 45kg
Volume 47 liters 68liters
Test Pressure 250 Bar
Material 37Mn
Colour RAL 3000
Thread Connection W28.8 x 1/14" - BS EN ISO 11363-1
Conformity ISO 9809 Part 1&2/TUV+UN
Mounting Vertical
Electric/Pneumatic - Input from
Control Panel
Cylinder Actuation
Manual/Pneumatic - Input from
Push Knob
Cylinder Storage
-20ºC to +55ºC
Temperature
Diameter 232mm 267mm
Height 1470mm 1526mm

DISCHARGE HEAD VALVES FOR MASTER CYLINDERS

NAFFCO CO₂ cylinder head valve shall be pressure seat type
valve. The head valve is available in two different valves for both
Master and Slave cylinder.

The solenoid operated head valve can be operated by electric

actuator and manual.

Model No. B04390031-NF

Test Pressure 300 Bar
Material Brass
Discharge Port/Outlet W21.8 x 1/14”
Inlet Connection W28.8 x 14TPI (25E ENISO 113631 - 1)

Port for Pilot Hose G ⅛"

Orifice Size Ø12mm

Flow Rate Kv= 2.66; Cv= 3.09

B04390031-NF

www.naffco.com 5
DISCHARGE HEAD VALVES FOR SLAVE CYLINDERS
Slave cylinder head valve is operated by using pneumatic release
device and is connected to the master cylinder by a pilot hose.

TECHNICAL DATA
Model No. B04800121-NF
Test Pressure 300 Bar
Material Brass
Discharge Port/Outlet W21.8 x 1/14”
Inlet Connection W28.8 x 14TPI (25E ENISO 113631 - 1)

Port for Pilot Hose G ⅛"

Orifice Size Ø12mm

Flow Rate Kv= 2.66; Cv= 3.09

B04800121-NF

CONSTANT FLOW & PRESSURE DISCHARGE REGULATOR

The pressure regulator modulates the discharge pressure to a
constant pressure, which still delivers the extinguishing agent
up to 120 seconds, but with significant performance and cost
benefits. It prevents discharge freeze-up and explosive force of
discharge. Low-pressure manifolds and pipework can be used -
that means lower costs.

After a system discharge, no reconditioning of the pressure

regulator is necessary. Functional tests are possible even while
the system is armed. The pressure regulator is screwed with a
gasket on the discharge port of the valve.

TECHNICAL DATA
Model No B08400003-NF
Material Brass
Inlet Pressure 200 / 300 Bar
Maximum Inlet Pressure 360 Bar
Orifice diameter 12 mm
Inlet Connection W21.8 x 1/14” DIN 477
Outlet Connection W21.8 x 1/14” DIN 477
Static outlet pressure 60 Bar

6 www.naffco.com
ELECTROMAGNETIC RELEASE DEVICES
ELECTROMAGNETIC RELEASE DEVICE
(with and without Diode)
The electromagnetic release device is used to actuate the
system electrically. It is mounted on top of the master valve and
is operated by an electrical signal from a fire detection system. In
order to actuate the electromagnetic release device a constant
DC voltage of 24V is required.
The electromagnetic release device can be combined with the
manual/pneumatic release device.

TECHNICAL DATA
B04425146-NF (with diode)
Part Number
B04425147-NF (without diode)
Valve Connection M42 x 1.5
Nominal Voltage 24 VDC
Electrical Connection --
Nominal Current 0.5 A
Protection Class IP65
Brass and Stainless Steel
Material
Plastic Protection Cap

Conformity 89/106/EEC

RESET TOOL FOR ELECTROMAGNETIC

RELEASE DEVICES
The reset tool is used to reset the electromagnetic release device
piston after system discharge. The reset tool is screwed into the
bottomof the electromagnetic release device.

TECHNICAL DATA

Part Number 02300064-NF

Connection M42 x 1.5

Material Brass

ADAPTER
The adapter is used for the connection of pilot hoses to the
manual/ pneumatic release device or to the pneumatic release
device.

TECHNICAL DATA

Part Number 029510006-NF

Connection G⅛"/M12 x 1.5

Material Brass

www.naffco.com 7
PNEUMATIC RELEASE DEVICE
This release device is used for pneumatic actuation of multiple
cylinders in series, which are connected to the master cylinder
by a pilot hose. Cylinders equipped with the pneumatic release
device serve as slave cylinders.

TECHNICAL DATA
Model No B04420066-NF
Material Brass
Working Pressure 300 Bar
Valve Connection M 42 x 1.5
Pneumatic Connection G ⅛"
200 Bar System: P Min = 15 Bar; P
Actuation Force/ Max = 240 Bar
Pressure 300 Bar System: P Min = 21 Bar; P
Max = 360 Bar

MANUAL/PNEUMATIC RELEASE DEVICE

The manual/pneumatic release device allows manual or
pneumatic actuation of several system components. This release
device is used for pneumatic actuation of multiple cylinders in
series, which are connected to the master cylinder by a pilot
hose. Manual actuation is accomplished by pulling the hand lever
on the manual/pneumatic release device. In the closed position
the manual/pneumatic release device is secured with a safety
pin. By removing the safety pin, the hand lever can be manually
pressed down to activate the valve so that inert gas is released

TECHNICAL DATA
Model No B04420065-NF
Material Brass & Stainless Steel
Working Pressure 300 Bar
Valve Connection M 42 x 1.5
Pneumatic Connection G ⅛"
Actuation Force <150N
200 Bar System: P Min = 15 Bar; P
Actuation Force/ Maxt = 240 Bar
Pressure 300 Bar System: P Min = 21 Bar; P
Max = 360 Bar

8 www.naffco.com
PILOT HOSE
The pilot hose is used to build up the pilot line, e.g. for the
connection of several release devices and/or for the connection
of the valve to the release device.

The pilot hose may only be used in accordance with component

approval in stationary inert gases fire extinguishing systems.
Several cylinders, equipped with valves, can be connected with
pilot hoses.

TECHNICAL DATA
Model No. B06920211-NF B06920212-NF B06920213-NF NHC6
Length 400 mm 700 mm 500 mm 520 mm
Connection 2 x M12 x 1.5

Bending Radius 75 mm

Nominal Diameter DN 6
Working Pressure 400 Bar
Burst Pressure 1600 Bar

• Connection - Galvanised steel

• Hose inner layer - Oil resistant synthetic rubber
Material
• Hose insert - Two high tensile steel wire braided inserts
• Hose outer layer - Oil resistant and weatherproof synthetic rubber

DISCHARGE HOSE
The discharge hose is used for the connection of the pressure
regulator to the check valve. The W21.8 x 1/14“ nut with the
inserted gasket is installed on the pressure regulator.
The G¾“ nut with the inserted gasket is
connected to a check valve.

TECHNICAL DATA
Model No. NHC18
Length 520 mm
Connection W21.8 x 1/14” • G¾”

Bending Radius 180 mm

Nominal Diameter DN 16
Max. Working Pressure 350 Bar
Burst Pressure 1400 Bar

• Connection - Galvanised steel

• Hose inner layer - Oil resistant synthetic rubber
Material
• Hose insert - Two high tensile steel wire braided inserts
• Hose outer layer - Oil resistant and weatherproof synthetic rubber

www.naffco.com 9
SAFETY DEVICE
Manifold safety device is to prevent over pressure during
discharge. In case of overpressure, the pressure safety device for
manifold release the extinguishing agent. The device is provided
with an male inlet which can be screwed into the manifold.

TECHNICAL DATA
Model No. 029730039

Material Brass

Connection Thread ½" to EN10226-1

Test Pressure 150 bar

Safety Release Pressure 190 bar

CHECK VALVE
Designed to avoid returns of the fluid inside the hydraulic circuit.
For ease of installation, check valves are designed to be installed
in either horizontal or vertical position.

TECHNICAL DATA
Maximum
Part Pressure
Size Hex. Height Pressure
Number Rating
Rating

504.110003BD ½" NPT 300 bar 30mm 77mm 1200 bar

504.110004BE ¾" NPT 300 bar 36mm 90mm 1200 bar

504.110005BF 1" NPT 300 bar 46mm 106mm 1200 bar

504.110007BH 1½" NPT 300 bar 60mm 140mm 1200 bar

504.110008BI 2" NPT 300 bar 75mm 160mm 1200 bar

10 www.naffco.com
DISCHARGE NOZZLE
Discharge nozzles are made of brass in four different sizes, for
different application. Nozzles are available with a connection
thread R1", R½" and R¾" and can be screwed into every fitting
corresponding to the pressure stage and the thread. Orifice
design to particular requirement with computer aided calculation
to assure the effectiveness of extinguishing agent and reliable
system design.

The nozzle is used to discharge the agent from the cylinder

through piping network to the enclosed hazard volume. The
nozzle selection depends on the hazard and location to be
protected. The nozzle has to be mounted at the ceiling level with
the orifice tip pointed vertically down. The nozzle outlet must
point downwards to distribute the extinguishing agent effectively
and to prevent pollution. The discharge pattern of the nozzle shall
be 360° & 180°.

The nozzle distributes the extinguishing agent evenly in the

extinguishing zone in the calculated flooding time. Nozzles are
designed to direct the discharge of inert gas using the stored
pressure from the cylinders.

TECHNICAL DATA
Nozzle Reference Nozzle Size Part Number Orifice 0 (mm) Discharge Pattern
N36003100 3
C45X - 20 N36005101 5 360º
N36010102 10
½"NPT N36003100 3
C45X - 21 N36005101 5 180º
N36010102 10
N30070200 7
C45X - 22 N36010201 10 360º
N36014202 14
¾"NPT N18007200 7
C45X - 23 N18010201 10 180º
N18014202 14
N36010300 10
C45X - 24 N36014301 14 360º
N36018302 18
1"NPT N18010300 10
C45X - 25 N18014301 14 180º
N18018302 18

PRESSURE & FLOW DETECTOR SWITCH

Used to send a signal that the system is discharging. Sends a
signal to a control panel or alarm box at the earliest phase of
discharge.

The pressure and flow detector switch is connected to the

manifold and to a power supply. It reacts in the earliest stage of
extinguishing agent discharge at 2 Bar pressure and energises or
de-energises electrically operated equipment.

TECHNICAL DATA
Model No 028250050-NF
Operating Pressure 2 Bar
Connection G½" or G¾"
Power Source 400 VAC/3A or 24 VAC/10A
IP Rating IP65

www.naffco.com 11
MANIFOLD
Manifolds are used to connect several cylinders at 100 bar
pressure. They can only be used with valves with pressure
regulators it available in 1 row and 2 row arrangement to connect
2 to 20 cylinders.

TECHNICAL DATA
267 Dia. 232 Dia.
Manifold Description
Cylinder Cylinder

2 Cylinder Manifold NFCO2-267-SRM2 NFCO2-232-SRM2

3 Cylinder Manifold NFCO2-267-SRM3 NFCO2-232-SRM3

4 Cylinder Manifold NFCO2-267-SRM4 NFCO2-232-SRM4

5 Cylinder Manifold NFCO2-267-SRM5 NFCO2-232-SRM5

MANIFOLD CHECK VALVE

The check valve prevents a back-flow of the extinguishing agent
into the cylinder. The check valve is provided with a connection
thread R1“ DIN EN 10226-1 for the connection to the manifold and
a connection thread G¾“ DIN ISO 228-1 for the connection to the
discharge hose.

Model No B04600008-NF

• Housing - Brass
Material • Ball - Stainless Steel
• Sealing - Thermoplastic

Connection Thread Inlet G¾" DIN ISO 228-1

Connection Thread Outlet R1” DIN EN 10226-1
Nominal Diameter DN 12
Working Pressure 300 Bar
Pressure to Open <0.1 Bar

CYLINDER MOUNTING PARTS

Galvanised steel wall mounting rails and clamps are used to double row arrangement with metal bracket. For floor mounting,
mount the cylinders in a vertical position to the wall for single & channels are used to mount the cylinders.

CYLINDER MOUNTING PARTS SINGLE & DOUBLE ROW ARRANGEMENT

NOTE: Steel Brackets Available Upon Request

12 www.naffco.com
BLEED VALVE
The bleed valve is a part of the pilot line. The device must be
mounted at the end of each pilot line at the last pneumatic
release device. This device is a security part, which protects the
system from unwanted tripping when a cylinder has a leak and
the pressure would increase in the pilot line. It allows a bleeding
till the pressure in the pilot line is under 0.7 Bar. The bleed valve
prevents an accidental system release.

TECHNICAL DATA
Model No 029730040-NF

Material Brass

Working Pressure 300 Bar

Connection Thread G⅛" ISO 228-1

Closing Pressure 0.7 - 1.5 Bar

SELECTOR VALVE
(MULTI-ZONE DISTRIBUTION)
Selector Valve allow a single agent supply to be utilized for protection of
multiple zones by using the same number of cylinders. It is necessary to
use the selector valve to utilize the multiple cylinders to protect the multiple
zones. Selector Valves direct the extinguishing agent to the appropriate
flooding zone and reduces the total amount of agent and number of
cylinders required.

The Selector Valve body is available in carbon steel. Selector valve is

a ball valve that control the flow of Inert gas through the piping network
until the valve is activated either by manually or electrically. The actuation
pressure for the selector valve is 8-10 bar pressure. Each Selector Valve is
equipped with the monitoring device which shows the valve Position (Open
or Closed) that provides a visual indication of the valve status.

TECHNICAL DATA
Part Number B05511 050-NF B05511 150-NF B05511 250-NF B05511 350-NF B05511 450-NF

Diamater G1" (DN25) G1½" (DN40) G2" (DN50) G2½" (DN65) G3" (DN80)

Working Pressure 140 Bar

Actuation Pressure 8 - 10 Bar

Material Carbon Steel

www.naffco.com 13
PNEUMATIC CONTROL PANEL
(MULTI-ZONE DISTRIBUTION)
The pneumatic control panel is made of several individual components, which are fixed on a support of control panel arrangement.

TECHNICAL DATA
S. No. DESCRIPTION S. No. DESCRIPTION
3/2Way Valve / Electro Pneumatic / 24 DC / UL-Coil / G1/8 /
1 13 Reducing, Brass, G 1/4"I, 1/4" NPT 0, WP 16 Bar, WS17
Bistable / 1-10bar / DN5 / Temp. -10 to +60°C
2 Mounting plate for 3/2-way Valve Connection G 1/8 14 Fixation "Normafix" K, Size 1, Clamp Size 63-80mm
L-fitting (Blue Series), Rotatable, R1/4a., for tube outside-Ø8 mm, Connector Type B / IP 65 / Contacts 2 + Grounding /
3 15 Cable Inlet PG / Ø6-8mm1
WP max. 15bar, Plastic/MS vern.
Fitting Straight, R 1/8 a, tube outside -Ø8 mm,
4 16 Screw in Fitting AGN 1/4" CEL06
WP max. 315 bar, WS117, WS214, Steel Zinc Coated
Plug, Hex 6mm, G1/4, O-Ring, WP Max. 60 Bar,
5 17 HP Tube 2SC DN 6 / B06920212
WT max. 80°C, Brass Nickel Coated
6 Silencer Sintered, Flat, G1/4a., WP Max. 10 Bar, WT-10°C bis 250°C 18 Bleed Valve 029730040
Plug with Hex / 1/4"NPT / Type Straight /
7 Hose Clamp, Steel Coated (W1), Clamp Size 60,0 - 80,0mm, B 20,0 mm 19 Steel Calv. Coated / Thread Sealed
8 Manometer Typ 111.11, Ø2.5", G 1/4" Bottom Radial, 0-16 Bat, UL252 20 Distance Sheet, Aluminium, 56 x 15 x 7 mm

9 Cover Sheet for Mounting Plate G1/4 for Connection G1/8 21 Distance Sheet, Aluminium, 45 x 45 x 8 mm

10 HP Regulator / 1/4' / NPT / 5-125 psig (0,3 to 3,5 Bar) / without Manometer 22 Screw Hex M8 x 20

11 Mounting Plate Aluminium / 450(H) x 1000(L) x 6(D) mm 23 Electrical Interface Box Rittal PK9521.050
Reducing Nipple, G 1/4a., G 1/8i., WS 17, WP Max. 60 Bar,
12 24 Connector
WT Max. 150°C, Brass Zinc Coated
25 Cable Trunking

PNEUMATIC CONTROL PANEL SIZE

PART NO. NAME ZONES LENGTH (mm) HEIGHT (mm) DEPTH (mm)
NF-SVCB02 2 Zones 470 450 6
NF-SVCB03 3 Zones 470 450 6
NF-SVCB04 4 Zones 470 450 6
NF-SVCB05 5 Zones 470 450 6
NF-SVCB06 6 Zones 700 450 6
NF-SVCB07 7 Zones 700 450 6
NF-SVCB08 Control panel with different 8 Zones 700 450 6
NF-SVCB09 configurations (zones) 9 Zones 700 450 6
NF-SVCB10 10 Zones 700 450 6
NF-SVCB11 11 Zones 1000 450 6
NF-SVCB12 12 Zones 1000 450 6
NF-SVCB13 13 Zones 1000 450 6
NF-SVCB14 14 Zones 1000 450 6
NF-SVCB15 15 Zones 1000 450 6

14 www.naffco.com
SELECTOR VALVE WITH PILOT - CYLINDER ASSEMBLY
(MULTI-ZONE DISTRIBUTION)
Pilot cylinder assembly for selector valve actuation consists Both of these actuation methods result in the opening of a nitrogen
of Manual / Pneumatic release device which allows manual pilot cylinder that pneumatically opens the Selector Valve. Each
or pneumatic actuation of the selector valve for the individual Selector Valve is equipped with the monitoring device which
zones for system operation. Manual actuation is accomplished by shows the valve Position (Open or Closed) that provides a visual
pulling the hand lever on the manual/pneumatic release device indication of the valve status. Pop Off Valve is used to reset the
is secured with a safety pin. By removing the safety pin, the hand Selector Valve after the system discharge.
lever can be manually pressed down to actuate the valve so that
the nitrogen is released from the cartridge. Electric magnetic
device is used to actuate the system electrically. It is mounted
top of the pilot cylinder valve and is operated by an electrical
signal of constant DC voltage of 24V electric solenoid from the
fire detection system.

1. Selector Valve 7. Manual/Pneumatic Release Device Part number:

2. High Pressure Primary Regulator (Set Pressure 6 to 10 Bar) B04420065-NF
UL Listed 8. Pressure Gauge, Patt number: 029720221-NF
3. ¼" High Pressure Pilot Hose (Max. Length 1.5Mtr) 9. Pilot Cylinder, W28.8x14TPI Threaded to 25E EN ISO
4. Constant Flow & Pressure Discharge Regulator, Part 113631-1
number: B8400003-NF 10. Pop off Valve, Set Pressure 175 Psi
5. Discharge Valve, Part number: B04801218-NF
6. Electromagnetic Release Device Part number:
B04425146-NF

www.naffco.com 15
WARNING SIGN

Model No.: NF-CO2-SW-01

WARNING SIGN:

VACATE
IMMEDIATELY

Model No.: NF-CO2-SW-02

WARNING SIGN:

DO NOT ENTER
UNTIL
VENTILATED

Model No.: NF-CO2-SW-03

WARNING SIGN:

WHEN ALARM
OPERATES

16 www.naffco.com
Model No.: NF-CO2-SW-04
WARNING SIGN:

NEARLY
SPACE
COLLECTION

Model No.: NF-CO2-SW-05

WARNING SIGN:

VENTILATE
BEFORE
ENTERING

Model No.: NF-CO2-SW-06

WARNING SIGN:

MANUAL
ACTIVATOR
 Serving Over 100 Countries Worldwide

NF-CA-CES-U0517A-P- - - -A-DXB