AADA10 - Covered Rhino command list:

 Geometry creation
o 0-dimensional objects
 Point (creates point)
 Points (creates multiple points)
o 1-dimensional objects
 Line (draws a single straight line segment)
 Polyline (draws a first degree curve made out of several straight line segments
or arcs)
 Curve (draws a third degree Nurbs curve)
 InterpCrv (draws a third degree interpolated Nurbs curve)
 Circle (draws a circle, which is a second degree Nurbs curve)
 Ellipse (draws an ellipse around the center with 2 different radii)
 Arc (draws an arc, which is a second degree Nurbs curve)
o 2-dimensional objects
 Rectangle (draws a rectangle)
 Polygon (draws an N-gon)
 SrfPt (Generates a Nurbs surface from 3 or 4 corner points)
 PlanarSrf (Generates a Nurbs surface from flat closed boundary curves)
 NetworkSrf (Generates a Nurbs surface from a grid of Nurbs curves)
 Loft (Generates a Nurbs surface from a linear array of Nurbs curves)
 EdgeSrf (Generates a Nurbs surface from 2,3 or 4 curve segments, which
describe it‘s boundary)
 Patch (Generates a Nurbs surface through various geometry. This tool is not
precise and shouldn‘t be used in high precision work)
o 3-dimensional objects
 Box (Generates a 3D box which is a Closed Nurbs Polysurface)
 Sphere (Generates a 3D sphere which is a Closed Nurbs Surface)
 Cyllinder (Generates a 3D box which is a Closed Nurbs Polysurface)
 Pipe (Generates a 3D cylinder along any given curve)
 Sweep1 (Generates Nurbs geometry by sweeping section curves along a rail
curve)
 Sweep2 (Generates Nurbs geometry by sweeping section curves along two rail
curves)
 Revolve (Generates Nurbs geometry by revolving a section curve around an axis)
 ExtrudeCrv (Generates Nurbs geometry from a curve by extruding it along given
uniform direction)
 ExtrudeSrf (Generates Nurbs geometry from a surface by extruding it along
given uniform direction)
 OffsetSrf (Generates Nurbs geometry from a surface by thickening it. Thickening
directions are perpendicular to the surface of the input curve)
o Form Modifiers:
 Trim (Cut a curve or a surface with any intersecting geometry)
 Split (Split a curve or a surface with any intersecting geometry)
  Rebuild (Rebuild a curve or a surface to have more/less control points or a
different degree)
 Extend (Extend a curve to any geometry which would be in it‘s extension path)
 Explode (Extract all separate straight line segments from a polyline)
 Fillet (join 2 non-paralel curves with an arc)
 Chamfer (join 2 non-paralel curves with a straight line segment)
 FilletCorners (round of all corners of a polyline)
 TweenCurves (Generate average curves between two boundary curves)
 PointsOn (F10 button) (Show control points of a curve or a surface)
 SolidPtOn (Show control points of a polysurface)
 Project (Project a curve on a surface along a given direction)
 ProjectToCPlane (Project a curve to be flat on the world „ground“)
 FilletEdge (Round off selected interior edges of a polysurface)
 ChamferEdge (Chamger selected interior edges of a polysurface)
 MergeSrf (Merge 2 perfectly matched surfaces into 1)
 BlendCrv (Join 2 separate curves by generating a seamless joining curve)
 BlendSrf (Join 2 separate surfaces by generating a seamless joining surface)
 Cap (fill all planar holes of an open polysurface)
o Solid operators
 BooleanUnion (Merge 2 closed polysurfaces into 1 closed polysurface)
 BooleanDifference (Substract a volume from one closed polysurface with
another closed polysurface)
 BooleanSplit (Split one closed polysurface into separate parts with another
closed polysurface)
o Utility
 ZSA (Zoom to selected geometry in all viewports)
 ZS (Zoom to selected geometry in current viewport)
 DupBorder (Generate curves from hole boundaries of an open 3D geometry)
 DupEdge (Generate curves from edges of a surface/polysurface)
 Move (Move geometry from one point to the other)
 Scale (Scale geometry uniformally)
 Scale1D (Scale geometry in 1 direction. In other words – stretch geometry)
 Rotate (Rotate geometry around given pont in XY world plane)
 Rotate3D (Rotate geometry around given axis)
 ExtractSrf (Extract a surface from a nurbs polysurface)
 Purge (Clean up the file, remove unused layers, etc.)
 Make2D (Generate a 2D linework projection of selected geometry)
 Hide (Hide selected geometry)
 Isolate (Hede everything except selected geometry)
 Show (show all hidden geometry)
 ShowSelected (only show geometry which you will select)
 Group (make a selection group from various geometries)
 Ungroup (deconstruct the selection group)
 PrintDisplay (Toggle between showing the model colours or the print colours)