• SAFETY PRECAUTIONS •

(Read these precautions before using this product.)

Before using this product, please read this manual and the relevant manuals carefully and pay full
attention to safety to handle the product correctly.
The precautions given in this manual are concerned with this product. For the safety precautions of the
programmable controller system, refer to the user's manual for the CPU module used.
In this manual, the safety precautions are classified into two levels: " ! WARNING " and " ! CAUTION".

Indicates that incorrect handling may cause hazardous conditions,

! WARNING
resulting in death or severe injury.

Indicates that incorrect handling may cause hazardous conditions,

! CAUTION resulting in minor or moderate injury or property damage.

Under some circumstances, failure to observe the precautions given under " ! CAUTION" may lead to
serious consequences.
Observe the precautions of both levels because they are important for personal and system safety.

Make sure that the end users read this manual and then keep the manual in a safe place for future
reference.

[Design Precautions]
! WARNING
• In the case of a communication failure in the network, the status of the error station will be as
follows:
(1) All inputs from remote I/O stations are turned off.
(2) All outputs from remote I/O stations are turned off.
Check the communication status information and configure an interlock circuit in the sequence
program to ensure that the entire system will operate safely.
Incorrect output or malfunction due to a communication failure may result in an accident.
• Outputs may remain on or off due to a failure of a remote I/O module. Configure an external
circuit for monitoring output signals that could cause a serious accident.

! CAUTION
• Use the module in an environment that meets the general specifications in this manual.
Failure to do so may result in electric shock, fire, malfunction, or damage to or deterioration of
the product.
• Do not install the control lines or communication cables together with the main circuit lines or
power cables. Keep a distance of 100mm (3.94 inches) or more between them. Failure to do so
may result in malfunction due to noise.

A-1 A-1
[Installation Precautions]
! CAUTION
• Do not directly touch any conductive parts of the module. Doing so can cause malfunction or
failure of the module.
• Securely fix the module with a DIN rail or mounting screws. Tighten the screws within the
specified torque range. Undertightening can cause drop of the screw, short circuit or
malfunction. Overtightening can damage the screw and/or module, resulting in drop, short
circuit, or malfunction.
• Securely connect the cable connectors. Poor contact may cause malfunction.

[Wiring Precautions]
! WARNING
• Shut off the external power supply for the system in all phases before wiring.
Failure to do so may result in electric shock or cause the module to fail or malfunction.

! CAUTION
• Ground the FG terminal to the protective ground conductor dedicated to the programmable
controller. Failure to do so may result in electric shock or malfunction.
• Tighten any unused terminal screws within the specified torque range (0.42 to 0.50N•m). Failure
to do so may cause a short circuit due to contact with a solderless terminal.
• Use applicable solderless terminals and tighten them within the specified torque range. If any
spade solderless terminal is used, it may be disconnected when the terminal screw comes
loose, resulting in failure.
• Check the rated voltage and terminal layout before wiring to the module, and connect the cables
correctly. Connecting a power supply with a different voltage rating or incorrect wiring may
cause a fire or failure.
• Tighten the terminal screw within the specified torque range. Undertightening can cause short
circuit, fire, or malfunction. Overtightening can damage the screw and/ or module, resulting in
drop, short circuit, fire, or malfunction.
• When fixing the CC-Link dedicated cable and the power cable through the pipes for transmission
or power supply line of the waterproof type remote I/O module, securely tighten the nuts with a
wrench. Undertightening can cause water intrusion, resulting in failure. (AJ65SBTW -16
only.)
• Tighten the communication adapter mounting screw or the waterproof cap within the specified
torque range. Undertightening can cause short circuit, fire, or malfunction. Overtightening can
damage the screw or the cap, resulting in short circuit or malfunction. (AJ65FBTA -16 only.)
• This product meets IP67 standard under the condition that the waterproof plugs, waterproof
caps, and communication adapter are all installed. (AJ65FBTA -16 only.)
• Do not connect the cable to an incorrect connector. The I/O connector, communication
connector, and power connector have the same interface. Doing so can cause malfunction or
failure of the module. (AJ65FBTA -16 only.)

A-2 A-2
[Wiring Precautions]
! CAUTION
• Prevent foreign matter such as dust or wire chips from entering the module. Such foreign matter
can cause a fire, failure, or malfunction.
• Place the cables in a duct or clamp them. If not, dangling cable may swing or inadvertently be
pulled, resulting in damage to the module or cables or malfunction due to poor contact.
• Do not install the control lines together with the communication cables, or bring them close to
each other. Failure to do so may cause malfunctions due to noise.
• When an overcurrent caused by an error of an external device or a failure of the programmable
controller flows for a long time, it may cause smoke and fire. To prevent this, configure an
external safety circuit, such as a fuse.
• When disconnecting the cable from the module, do not pull the cable by the cable part. For the
cable with connector, hold the connector part of the cable. For the cable connected to the
terminal block, loosen the terminal screw. Pulling the cable connected to the module may result
in malfunction or damage to the module or cable.

[Starting and Maintenance Precautions]

! WARNING
• Do not touch any terminal while power is on. Doing so will cause electric shock or malfunction.
• Shut off the external power supply for the system in all phases before cleaning the module or
retightening the terminal screws or module mounting screws. Failure to do so may result in
electric shock.
• Set the sink/source selector switch after shutting off the power supply at all phases.
Failure to do so may result in failures or malfunctions in the opponent device.

! CAUTION
• Do not disassemble or modify the modules. Doing so may cause failure, malfunction, injury, or a
fire.
• Do not drop or apply strong shock to the module. Doing so may damage the module.
• Shut off the external power supply for the system in all phases before mounting or removing a
module. Failure to do so may cause the module to fail or malfunction.
• After the first use of the product, do not mount/remove the terminal block to/from the module
more than 50 times (IEC 61131-2 compliant).
• Before handling the module, touch a conducting object such as a grounded metal to discharge
the static electricity from the human body. Failure to do so may cause the module to fail or
malfunction.

[Disposal Precautions]
! CAUTION
• When disposing of this product, treat it as industrial waste.

A-3 A-3
 • CONDITIONS OF USE FOR THE PRODUCT •
(1) Mitsubishi programmable controller ("the PRODUCT") shall be used in conditions;
i) where any problem, fault or failure occurring in the PRODUCT, if any, shall not lead to any major or
serious accident; and
ii) where the backup and fail-safe function are systematically or automatically provided outside of the
PRODUCT for the case of any problem, fault or failure occurring in the PRODUCT.

(2) The PRODUCT has been designed and manufactured for the purpose of being used in general
industries.
MITSUBISHI SHALL HAVE NO RESPONSIBILITY OR LIABILITY (INCLUDING, BUT NOT LIMITED
TO ANY AND ALL RESPONSIBILITY OR LIABILITY BASED ON CONTRACT, WARRANTY, TORT,
PRODUCT LIABILITY) FOR ANY INJURY OR DEATH TO PERSONS OR LOSS OR DAMAGE TO
PROPERTY CAUSED BY the PRODUCT THAT ARE OPERATED OR USED IN APPLICATION NOT
INTENDED OR EXCLUDED BY INSTRUCTIONS, PRECAUTIONS, OR WARNING CONTAINED IN
MITSUBISHI'S USER, INSTRUCTION AND/OR SAFETY MANUALS, TECHNICAL BULLETINS AND
GUIDELINES FOR the PRODUCT.
("Prohibited Application")
Prohibited Applications include, but not limited to, the use of the PRODUCT in;
y Nuclear Power Plants and any other power plants operated by Power companies, and/or any other
cases in which the public could be affected if any problem or fault occurs in the PRODUCT.
y Railway companies or Public service purposes, and/or any other cases in which establishment of a
special quality assurance system is required by the Purchaser or End User.
y Aircraft or Aerospace, Medical applications, Train equipment, transport equipment such as Elevator
and Escalator, Incineration and Fuel devices, Vehicles, Manned transportation, Equipment for
Recreation and Amusement, and Safety devices, handling of Nuclear or Hazardous Materials or
Chemicals, Mining and Drilling, and/or other applications where there is a significant risk of injury to
the public or property.

Notwithstanding the above, restrictions Mitsubishi may in its sole discretion, authorize use of the
PRODUCT in one or more of the Prohibited Applications, provided that the usage of the PRODUCT is
limited only for the specific applications agreed to by Mitsubishi and provided further that no special
quality assurance or fail-safe, redundant or other safety features which exceed the general
specifications of the PRODUCTs are required. For details, please contact the Mitsubishi
representative in your region.

A-4 A-4
REVISIONS
* The manual number is given on the bottom left of the back cover.
Print Date * Manual Number Revision
June 1998 SH(NA)-4007-A First printing
Nov. 1998 SH(NA)-4007-B Additional model
AJ65SBTB1-8D, AJ65SBTC4-16D, AJ65SBTW4-16D, AJ65SBTB1-8T,
AJ65SBTC4-16DT, AJ65SBTW4-16DT
Addition
Section 7.3, 7.4
Correction
Section 1.1, 1.2, 1.4, Chapter 2, 4, 5, 6, Section 7.1, Appendix 1
Apr. 1999 SH(NA)-4007-C Addition
Contents, Section 8.2.2
June 1999 SH(NA)-4007-D Additional model
AJ65SBTB1-32T1, AJ65SBTCF1-32D, AJ65SBTCF1-32T,
AJ65SBTCF1-32DT
Nov. 1999 SH(NA)-4007-E Addition
Section 1.4, 4.1.6, 4.1.7, 4.4, 5.1.8, 5.1.9, 5.1.10, 5.1.11, 5.3, 6.1, 6.4, 7.4,
Appendix 1.6, 1.7, 1.8
Correction
Section 1.1, 1.2, 1.3, 1.5, 1.6, Chapter 2, Chapter 3, Section 4.2.1, 4.3.1,
6.2.1, 6.3.1, Section 7.1, 7.4, 8.2.1, Appendix 1
Additional model
AJ65SBTB1-32DT, AJ65SBTCF1-32D, AJ65SBTCF1-32T,
AJ65SBTCF1-32DT, AJ65SBTB2-8A, AJ65SBTB2-16A, AJ65SBTB2-8R,
AJ65SBTB2-16R, AJ65SBTB2-8S, AJ65SBTB2-16S
Dec. 1999 SH(NA)-4007-F Addition
Section 1.2, 4.1.6, 4.1.7, 5.1.8, 5.1.9, 5.1.10, 5.1.11
Mar. 2000 SH(NA)-4007-G Additional model
AJ65SBTB2N-8A, AJ65SBTB2N-16A, AJ65SBTB3-8D, AJ65SBTB3-16D,
AJ65SBTB2-8T, AJ65SBTB2-16T, AJ65SBTB2N-8R, AJ65SBTB-16R,
AJ65SBTB2N-8S, AJ65SBTB2N-16S, AJ65SBTB32-8DT,
AJ65SBTB32-16DT, AJ65SBTB1-16DT, AJ65SBTB1-16DT1,
AJ65SBTB1-32DT1
Addition
Section 4.1.8, 4.1.9, 4.1.10, 4.1.11, Section 5.1.12, 5.1.13, 5.1.14, 5.1.15,
5.1.16, 5.1.17, Section 6.1.1, 6.1.3, 6.1.4, 6.1.5, 6.1.6, Appendix 1.9, 1.10
Oct. 2000 SH(NA)-4007-H Additional model
AJ65VBTCU3-8D1, AJ65VBTCU3-16D1, AJ65VBTCU2-8T,
AJ65VBTCU2-16T, AJ65VBTCF1-32DT1
Addition
Section 4.5, 5.4, 6.5, 7.2.3, 7.2.4, Appendix 1.13
Correction
Section 1.1, 1.4, 1.5, Chapter 2, Section 4.3.1, 7.1
Deletion
AJ65SBTB2-8A, AJ65SBTB2-16A, AJ65SBTB2-8R, AJ65SBTB2-16R,
AJ65SBTB2-8S, AJ65SBTB2-16S

A-5 A-5
Print Date * Manual Number Revision
Jan. 2001 SH(NA)-4007-I Additional model
AJ65FBTA4-16D, AJ65FBTA4-16DE, AJ65FBTA42-16DT,
AJ65FBTA42-16DTE
Addition
Section 1.6, 7.4, Appendix 1.14
Correction
Section 1.2, 1.4, 1.5, Chapter 2,3, Section 4.5.2, 5.3.1, 5.4.1, 5.4.2, 6.5.1,
7.1, Appendix 1.13
Jul. 2001 SH(NA)-4007-J Additional model
AJ65FBTA2-16T, AJ65FBTA2-16TE
Correction
Section 1.2, 1.4, 1.5, 4.1.6, 4.1.7, 4.2.1, 4.2.2, 4.3.1, 6.2.1, 6.2.2, 6.3.1,
6.5.1, 6.6.1, 6.6.2, 7.2.3, Appendix 1.14
Sep. 2001 SH(NA)-4007-K Additional model
AJ65SBTB1-16DT2, AJ65SBTB1-32DT2
Correction
Section 1.4, 6.1.1, 8.2.1, Appendix 1.13
Jan. 2002 SH(NA)-4007-L Additional model
AJ65SBTB1-8T1, AJ65SBTB2-8T1, AJ65SBTB2-16T1, AJ65SBTC1-32T1,
AJ65SBTB1-16DT3, AJ65SBTB1-32DT3, AJ65SBTB32-8DT2,
AJ65SBTB32-16DT2, AJ65SBTC4-16DT2, AJ65SBTC1-32DT2,
AJ65SBTC1-32DT3
Correction
Section 1.3, 1.4, 1.5, 5.5.2, 6.1.1, 7.7, 8.2.1, Appendix 1.13
Changed item numbers
Section 5.1.4 to Section 5.1.9 Section 5.1.5 to Section 5.1.10
Section 5.1.10 to Section 5.1.13 Section 5.1.13 to Section 5.1.16
Section 6.1.5 to Section 6.1.6 Section 6.1.9 to Section 6.1.10
Section 6.2.2 to Section 6.2.3 Section 6.2.3 to Section 6.2.4
Dec. 2002 SH(NA)-4007-M Correction
Section 2, Section 4 to Section 6, Section 8.2.1
May 2003 SH(NA)-4007-N Correction
Section 1.3, 1.6
Jun. 2004 SH(NA)-4007-O Additional model
AJ65VBTS3-16D, AJ65VBTS3-32D, AJ65VBTS2-16T, AJ65VBTS2-32T,
AJ65VBTS32-16DT, AJ65VBTS32-32DT, AJ65VBTCE3-8D,
AJ65VBTCE3-16D, AJ65VBTCE2-8T, AJ65VBTCE2-16T,
AJ65VBTCE32-16DT
Addition
Section 1.6.1 to 1.6.3, 4.5.3 to 4.5.5, 5.4.3 to 5.4.5, 6.5.2 to 6.5.4, 7.8, 7.9
Appendix 1.15, 1.16
Correction
Chapter 1, 2, Section 4.4.1, 4.5, 5.1, 5.4, 6.1, 6.5, 6.2.2, 6.4.1, 6.5.1, 7.2 to
7.4
Oct. 2004 SH(NA)-4007-P Correction
Section 1.1, 1.3 to 1.5, Chapter 2, 3, 4 to 6, Section 7.1, 7.4.2, 7.6, 7.7,
7.9.2, APPENDIX

A-6 A-6
Print Date * Manual Number Revision
May 2005 SH(NA)-4007-Q Additional model
AJ65VBTCE3-32D, AJ65SBTC4-16DN, AJ65SBTC4-16DE,
AJ65VBTCE32-32DT
Addition
Section 4.3.3, 4.4.3, 4.4.4, 6.3.2
Correction
SAFETY PRECAUTION, About Manuals, Compliance with the EMC and
Low Voltage Directives, Section 1.1, 1.2, 1.4, 1.5, Chapter 2,
Chapter 4 to 6, Section 7.1, 7.5, 7.7, 7.8.2, 7.9.2, Appendix 1.1, 1.2, 1.4,
1.5 to 1.10, 1.14
Changed item numbers
The order of section numbers has been changed in Chapters 4 through 6
Sep. 2005 SH(NA)-4007-R Correction
Chapter 4, through 6 have been changed for the external connection
diagrams
Sep. 2006 SH(NA)-4007-S Additional model
AJ65SBTB1B-16TE1, AJ65SBTB1-32TE1, AJ65SBTB1-32DTE1
Addition
Section 5.1.13, 5.1.14, 6.1.13
Correction
SAFETY PRECAUTION, Section 1.2, 1.4, Chapter 2, Section 7.1, 8.2.1,
8.2.2, Appendix 1.8
F.G symbol is generally revised.
Changed item numbers
Section 5.1.13 → Section 5.1.15
Section 5.1.14 → Section 5.1.16
Section 5.1.15 → Section 5.1.17
Section 5.1.16 → Section 5.1.18
Jan. 2007 SH(NA)-4007-T Additional model
AJ65SBTB3-16D5, AJ65SBTB1-32D5
Addition
Section 4.1.8, 4.1.11
Correction
Section 1.2, 1.4, Chapter 2, Section 5.1.17, 5.1.18, 8.2.2
Chapter 4 to 6 have been changed for specifications and external
connection diagrams.
Changed item numbers
Section 4.1.8 → Section 4.1.9
Section 4.1.9 → Section 4.1.10

A-7 A-7
Print Date * Manual Number Revision
Mar. 2007 SH(NA)-4007-U Additional model
AJ65DBTB1-32D, AJ65DBTB1-32T1, AJ65DBTB1-32R, AJ65DBTB1-
32DT1, AJ65DBTB1-32DR
Addition
Section 4.1.12, 5.1.19, 5.1.20, 6.1.14, 6.1.15, 7.10, 7.10.1, 7.10.2, 7.10.3,
7.10.4, 7.11, Appendix 1.15
Correction
Section 1.2, 1.3, 1.4, 1.5, Chapter 2, Section 4.3.1, 5.1.17, 5.1.18, 6.4.1,
6.4.2, 6.6.1, 6.6.2, 7.1
Sep. 2007 SH(NA)-4007-V Additional model
AJ65SBTB32-16DR, AJ65SBTB3-16KD, AJ65SBTB1-32KD,
AJ65SBTB32-16KDT2, AJ65SBTB32-16KDT8, AJ65SBTB1-32KDT2,
AJ65SBTB1-32KDT8
Addition
Section 4.1.8, 4.1.11, 6.1.9, 6.1.10, 6.1.11, 6.1.15, 6.1.17, Appendix 1.16
Correction
Section 1.2, 1.3, 1.4, Chapter 2, Section 6.6.3, 7.1
Changed item numbers
Section 4.1.8 → Section 4.1.9
Section 4.1.9 → Section 4.1.10
Section 4.1.10 → Section 4.1.12
Section 4.1.11 → Section 4.1.13
Section 4.1.12 → Section 4.1.14
Section 6.1.9 → Section 6.1.12
Section 6.1.10 → Section 6.1.13
Section 6.1.11 → Section 6.1.14
Section 6.1.12 → Section 6.1.16
Section 6.1.13 → Section 6.1.18
Section 6.1.14 → Section 6.1.19
Section 6.1.15 → Section 6.1.20
Oct. 2007 SH(NA)-4007-W Additional model
AJ65SBTB32-16KDR
Addition
Section 6.1.12
Correction
Section 1.2, 1.4, Chapter 2
Changed item numbers
Section 6.1.12 → Section 6.1.13
Section 6.1.13 → Section 6.1.14
Section 6.1.14 → Section 6.1.15
Section 6.1.15 → Section 6.1.16
Section 6.1.16 → Section 6.1.17
Section 6.1.17 → Section 6.1.18
Section 6.1.19 → Section 6.1.20
Section 6.1.20 → Section 6.1.21

A-8 A-8
Print Date * Manual Number Revision
Oct. 2008 SH(NA)-4007-X Additional model
AJ65VBTCFJ1-32DT1
Addition
Section 1.3.1, 1.3.2, 1.3.3, 1.3.4, 1.3.5, 4.4.1, 4.4.5, 5.2.1, 5.2.2, 5.3.1,
5.3.1, 6.5.3
Correction
Section 1.3
Jan. 2010 SH(NA)-4007-Y This manual was revised in accordance with IEC 60617.
Additional model
AJ65VBTCE3-16DE, AJ65VBTCE3-32DE
Addition
SAFETY PRECAUTION, Section 1.3.1, 1.4, 1.6.2, 1.7, 4.3.2, 4.3.3, 7.1,
7.2.3, 7.2.4, 7.5, 7.7
Correction
CONDITIONS OF USE FOR THE PRODUCT, Section 4.3.4, 4.3.5
Mar. 2011 SH(NA)-4007-Z This manual was revised in accordance.
Dec. 2011 SH(NA)-4007-AA Additional model
AJ65VBTCE3-16TE, AJ65VBTCE3-16DTE, AJ65VBTCE3-32DTE
Addition
Section 5.3.3, 6.3.2, 6.3.4
Correction
Chapter 3, Section 1.3.1 to 1.3.3, 1.4, 1.5, 4.6.3, 5.1.19, 6.1.1, 6.1.2,
6.1.7 to 6.1.12, 6.1.20, 6.2.1, 6.2.2, 6.3.1, 6.3.3, 6.4.1, 6.4.2, 6.6.1 to 6.6.3,
7.1, 7.2.2, 7.8.2, 8.1
Changed item numbers
Section 6.3.2 → Section 6.3.3

Japanese Manual Version SH-3307-AC

This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent
licenses. Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property
rights which may occur as a result of using the contents noted in this manual.
© 1998 MITSUBISHI ELECTRIC CORPORATION
A-9 A-9
 INTRODUCTION

Thank you for purchasing the MELSEC-A series programmable controller.

Before using the equipment, please read this manual carefully to develop full familiarity with the functions
and performance of the A-series programmable controller you have purchased, so as to ensure correct use.
Please forward a copy of this manual to the end user.

CONTENTS
SAFETY PRECAUTIONS..............................................................................................................................A- 1
CONDITIONS OF USE FOR THE PRODUCT .............................................................................................A- 4
REVISIONS ....................................................................................................................................................A- 5
INTRODUCTION............................................................................................................................................A-10
CONTENTS....................................................................................................................................................A-10
ABOUT MANUALS ........................................................................................................................................A-15
COMPLIANCE WITH THE EMC AND LOW VOLTAGE DIRECTIVES.......................................................A-15

1 OVERVIEW 1- 1 to 1-34
1.1 Features .................................................................................................................................................. 1- 1
1.2 Identifying the Compact Remote I/O Module Type................................................................................ 1- 4
1.3 Precautions for use of remote I/O modules ........................................................................................... 1- 5
1.3.1 Input module..................................................................................................................................... 1- 5
1.3.2 Output module.................................................................................................................................. 1-13
1.3.3 Modules with protection functions ................................................................................................... 1-20
1.4 Specification List ..................................................................................................................................... 1-21
1.5 Parts Sold Separately ............................................................................................................................. 1-29
1.6 Recommended Connection Device List................................................................................................. 1-31
1.6.1 Recommended connection devices for low profile waterproof remote I/O module ....................... 1-31
1.6.2 Recommended connection devices for low profile sensor connector (e-CON)
remote I/O module............................................................................................................................ 1-32
1.7 About the Generic, Abbreviated and Technical Terms Used in This Manual....................................... 1-33

2 NAMES AND SETTINGS FOR EACH PART 2- 1 to 2-26

3 SPECIFICATIONS 3- 1 to 3- 2

4 SPECIFICATIONS FOR INPUT MODULES 4- 1 to 4-71

4.1 Terminal Block Type Input Module.......................................................................................................... 4- 1
4.1.1 AJ65SBTB2N-8A 100VAC input module ........................................................................................ 4- 1
4.1.2 AJ65SBTB2N-16A 100VAC input module ...................................................................................... 4- 3
4.1.3 AJ65SBTB1-8D 24VDC input module
(positive common (sink), negative common (source) loading) ....................................... 4- 5
4.1.4 AJ65SBTB3-8D 24VDC input module
(positive common (sink), negative common (source) loading) ....................................... 4- 6
4.1.5 AJ65SBTB1-16D 24VDC input module
(positive common (sink), negative common (source) loading) ....................................... 4- 7
4.1.6 AJ65SBTB1-16D1 24VDC input module
(positive common (sink), negative common (source) loading) ....................................... 4- 8

A - 10 A - 10
 4.1.7 AJ65SBTB3-16D 24VDC input module
(positive common (sink), negative common (source) loading) ....................................... 4- 9
4.1.8 AJ65SBTB3-16KD 24VDC input module
(positive common (sink), negative common (source) loading) ....................................... 4-11
4.1.9 AJ65SBTB3-16D5 5VDC input module
(positive common (sink), negative common (source) loading) ....................................... 4-13
4.1.10 AJ65SBTB1-32D 24VDC input module
(positive common (sink), negative common (source) loading) ...................................... 4- 15
4.1.11 AJ65SBTB1-32KD 24VDC input module
(positive common (sink), negative common (source) loading) ...................................... 4- 17
4.1.12 AJ65SBTB1-32D1 24VDC input module
(positive common (sink), negative common (source) loading) ....................................... 4-19
4.1.13 AJ65SBTB1-32D5 5VDC input module
(positive common (sink), negative common (source) loading) ....................................... 4-21
4.1.14 AJ65DBTB1-32D 24VDC input module
(positive common (sink), negative common (source) loading) ...................................... 4-23
4.2 Spring Clamp Terminal Block Type Input Module .................................................................................. 4-25
4.2.1 AJ65VBTS3-16D 24VDC input module (positive common (sink type)) .......................................... 4-25
4.2.2 AJ65VBTS3-32D 24VDC input module (positive common (sink type)) .......................................... 4-28
4.3 Sensor Connector (e-CON) Type Input Module ..................................................................................... 4-31
4.3.1 AJ65VBTCE3-8D 24VDC input module (positive common (sink type)).......................................... 4-31
4.3.2 AJ65VBTCE3-16D 24VDC input module (positive common (sink type))........................................ 4-34
4.3.3 AJ65VBTCE3-32D 24VDC input module (positive common (sink type))........................................ 4-37
4.3.4 AJ65VBTCE3-16DE 24VDC input module (negative common (source type)) ............................... 4-40
4.3.5 AJ65VBTCE3-32DE 24VDC input module (negative common (source type)) ............................... 4-43
4.4 One-Touch Connector Type Input Module.............................................................................................. 4-46
4.4.1 AJ65VBTCU3-8D1 24VDC input module (positive common (sink type)) ....................................... 4-46
4.4.2 AJ65SBTC4-16D 24VDC input module
(positive common (sink), negative common (source) loading) ....................................... 4-49
4.4.3 AJ65SBTC4-16DN 24VDC input module (positive common (sink type)) ....................................... 4-52
4.4.4 AJ65SBTC4-16DE 24VDC input module (negative common (source type)) ................................. 4-54
4.4.5 AJ65VBTCU3-16D1 24VDC input module (positive common (sink type)) ..................................... 4-56
4.4.6 AJ65SBTC1-32D 24VDC input module
(positive common (sink), negative common (source) loading) ....................................... 4-59
4.4.7 AJ65SBTC1-32D1 24VDC input module
(positive common (sink), negative common (source) loading) ....................................... 4-61
4.5 FCN Connector Type Input Module......................................................................................................... 4-63
4.5.1 AJ65SBTCF1-32D 24VDC input module
(positive common (sink), negative common (source) loading) ....................................... 4-63
4.6 Waterproof Type Input Module ................................................................................................................ 4-65
4.6.1 AJ65FBTA4-16D 24VDC input module (positive common (sink type)) .......................................... 4-65
4.6.2 AJ65FBTA4-16DE 24VDC input module (negative common (souce type)) ................................... 4-67
4.6.3 AJ65SBTW4-16D 24VDC input module
(positive common (sink), negative common (source) loading) ....................................... 4-69

5 SPECIFICATIONS FOR OUTPUT MODULES 5- 1 to 5-72

5.1 Terminal Block Type Output Module ....................................................................................................... 5- 1
5.1.1 AJ65SBTB1-8T transistor output module (sink type)....................................................................... 5- 1
5.1.2 AJ65SBTB1-8T1 transistor output module (sink type)..................................................................... 5- 3

A - 11 A - 11
 5.1.3 AJ65SBTB2-8T transistor output module (sink type)....................................................................... 5- 5
5.1.4 AJ65SBTB2-8T1 transistor output module (sink type)..................................................................... 5- 7
5.1.5 AJ65SBTB1-16T transistor output module (sink type)..................................................................... 5- 9
5.1.6 AJ65SBTB1-16T1 transistor output module (sink type) .................................................................. 5-11
5.1.7 AJ65SBTB2-16T transistor output module (sink type)..................................................................... 5-13
5.1.8 AJ65SBTB2-16T1 transistor output module (sink type) .................................................................. 5-15
5.1.9 AJ65SBTB1-32T transistor output module (sink type)..................................................................... 5-17
5.1.10 AJ65SBTB1-32T1 transistor output module (sink type) ................................................................ 5-19
5.1.11 AJ65SBTB1-8TE transistor output module (source type) ............................................................. 5-21
5.1.12 AJ65SBTB1-16TE transistor output module (source type) ........................................................... 5-23
5.1.13 AJ65SBTB1B-16TE1 transistor output module (source type)....................................................... 5-25
5.1.14 AJ65SBTB1-32TE1 transistor output module (source type) ......................................................... 5-27
5.1.15 AJ65SBTB2N-8R contact output module....................................................................................... 5-29
5.1.16 AJ65SBTB2N-16R contact output module..................................................................................... 5-31
5.1.17 AJ65SBTB2N-8S triac output module............................................................................................ 5-33
5.1.18 AJ65SBTB2N-16S triac output module.......................................................................................... 5-35
5.1.19 AJ65DBTB1-32T1 transistor output module (sink type) ............................................................... 5-37
5.1.20 AJ65DBTB1-32R contact output module ....................................................................................... 5-39
5.2 Spring Clamp Terminal Block Type Output Module .............................................................................. 5-41
5.2.1 AJ65VBTS2-16T transistor output module (sink type) ................................................................... 5-41
5.2.2 AJ65VBTS2-32T transistor output module (sink type) ................................................................... 5-44
5.3 Sensor Connector (e-CON) Type Output module ................................................................................. 5-47
5.3.1 AJ65VBTCE2-8T transistor output module (sink type)................................................................... 5-47
5.3.2 AJ65VBTCE2-16T transistor output module (sink type)................................................................. 5-50
5.3.3 AJ65VBTCE3-16TE transistor output module (source type).......................................................... 5-53
5.4 One-Touch Connector Type Output Module.......................................................................................... 5-56
5.4.1 AJ65VBTCU2-8T transistor output module (sink type).................................................................... 5-56
5.4.2 AJ65VBTCU2-16T transistor output module (sink type).................................................................. 5-59
5.4.3 AJ65SBTC1-32T transistor output module (sink type) .................................................................... 5-62
5.4.4 AJ65SBTC1-32T1 transistor output module (sink type) .................................................................. 5-64
5.5 FCN Connector Type Output Module..................................................................................................... 5-66
5.5.1 AJ65SBTCF1-32T transistor output module (sink type) .................................................................. 5-66
5.6 Waterproof Type Output Module ............................................................................................................ 5-68
5.6.1 AJ65FBTA2-16T transistor output module (sink type)..................................................................... 5-68
5.6.2 AJ65FBTA2-16TE transistor output module (source type).............................................................. 5-70

6 SPECIFICATIONS FOR COMBINED MODULES 6- 1 to 6-87

6.1 Terminal Block Type Combined Module ................................................................................................. 6- 1
6.1.1 AJ65SBTB32-8DT combined module .............................................................................................. 6- 1
6.1.2 AJ65SBTB32-8DT2 combined module ............................................................................................ 6- 3
6.1.3 AJ65SBTB1-16DT combined module .............................................................................................. 6- 5
6.1.4 AJ65SBTB1-16DT1 combined module ............................................................................................ 6- 7
6.1.5 AJ65SBTB1-16DT2 combined module ............................................................................................ 6- 9
6.1.6 AJ65SBTB1-16DT3 combined module ............................................................................................ 6-11
6.1.7 AJ65SBTB32-16DT combined module ............................................................................................ 6-13
6.1.8 AJ65SBTB32-16DT2 combined module .......................................................................................... 6-15
6.1.9 AJ65SBTB32-16KDT2 combined module........................................................................................ 6-17
6.1.10 AJ65SBTB32-16KDT8 combined module...................................................................................... 6-19
6.1.11 AJ65SBTB32-16DR combined module.......................................................................................... 6-21

A - 12 A - 12
 6.1.12 AJ65SBTB32-16KDR combined module ....................................................................................... 6-23
6.1.13 AJ65SBTB1-32DT combined module ............................................................................................ 6-25
6.1.14 AJ65SBTB1-32DT1 combined module .......................................................................................... 6-27
6.1.15 AJ65SBTB1-32DT2 combined module .......................................................................................... 6-29
6.1.16 AJ65SBTB1-32KDT2 combined module........................................................................................ 6-31
6.1.17 AJ65SBTB1-32DT3 combined module .......................................................................................... 6-33
6.1.18 AJ65SBTB1-32KDT8 combined module........................................................................................ 6-35
6.1.19 AJ65SBTB1-32DTE1 combined module........................................................................................ 6-37
6.1.20 AJ65DBTB1-32DT1 combined module .......................................................................................... 6-39
6.1.21 AJ65DBTB1-32DR combined module............................................................................................ 6-41
6.2 Spring Clamp Terminal Block Type Combined Module......................................................................... 6-43
6.2.1 AJ65VBTS32-16DT combined module ............................................................................................ 6-43
6.2.2 AJ65VBTS32-32DT combined module ............................................................................................ 6-46
6.3 Sensor Connector (e-CON) Type Combined Module............................................................................ 6-49
6.3.1 AJ65VBTCE32-16DT combined module.......................................................................................... 6-49
6.3.2 AJ65VBTCE3-16DTE combined module ......................................................................................... 6-52
6.3.3 AJ65VBTCE32-32DT combined module.......................................................................................... 6-55
6.3.4 AJ65VBTCE3-32DTE combined module ......................................................................................... 6-58
6.4 One-Touch Connector Type Combined Module.................................................................................... 6-61
6.4.1 AJ65SBTC4-16DT combined module .............................................................................................. 6-61
6.4.2 AJ65SBTC4-16DT2 combined module ............................................................................................ 6-63
6.4.3 AJ65SBTC1-32DT combined module .............................................................................................. 6-65
6.4.4 AJ65SBTC1-32DT1 combined module ............................................................................................ 6-67
6.4.5 AJ65SBTC1-32DT2 combined module ............................................................................................ 6-69
6.4.6 AJ65SBTC1-32DT3 combined module ............................................................................................ 6-71
6.5 FCN Connector Type Combined Module............................................................................................... 6-73
6.5.1 AJ65SBTCF1-32DT combined module............................................................................................ 6-73
6.5.2 AJ65VBTCF1-32DT1 combined module.......................................................................................... 6-75
6.5.3 AJ65VBTCFJ1-32DT1 combined module........................................................................................ 6-78
6.6 Waterproof Type Combined Module ...................................................................................................... 6-81
6.6.1 AJ65FBTA42-16DT combined module ............................................................................................ 6-81
6.6.2 AJ65FBTA42-16DTE combined module .......................................................................................... 6-83
6.6.3 AJ65SBTW4-16DT combined module ............................................................................................. 6-85

7 HANDLING OF COMPACT REMOTE I/O MODULES 7- 1 to 7-38

7.1 Handling and Installation Precautions .................................................................................................... 7- 1
7.2 Wiring Procedures for One-touch Connector Plugs .............................................................................. 7- 9
7.2.1 List of one-touch connector plugs.................................................................................................... 7- 9
7.2.2 Precautions for transition wiring of one-touch connector for power supply and FG ...................... 7-10
7.2.3 Wiring procedures for the one-touch connector.............................................................................. 7-11
7.2.4 Wiring procedures for the one-touch connector for communication .............................................. 7-13
7.2.5 Wiring procedures for the one-touch connector for power supply and FG .................................... 7-15
7.3 Handling of the Waterproof-type Remote I/O Module ........................................................................... 7-17
7.3.1 List of dustproof and waterproof caps ............................................................................................. 7-17
7.3.2 Waterproof plug attachment procedure........................................................................................... 7-17
7.3.3 Wiring procedure for the terminal block........................................................................................... 7-18
7.4 Handling of the Low Profile Waterproof Type Remote I/O Module ....................................................... 7-19
7.4.1 List of waterproof caps ..................................................................................................................... 7-19
7.4.2 Waterproof cap installation method ................................................................................................. 7-19

A - 13 A - 13
7.5 Connectors and Tools Used for Connecting the FCN Connector Cables ............................................ 7-20
7.6 Attaching and Removing the Protective Cover for the Compact Remote I/O Module ......................... 7-21
7.7 Connection Method of CC-Link Dedicated Cable.................................................................................. 7-24
7.8 Handling of Spring Clamp Terminal Block Type Remote I/O Module................................................... 7-28
7.8.1 Installation and removal of the spring clamp terminal block ........................................................... 7-28
7.8.2 Procedure for wiring the spring clamp terminal block ..................................................................... 7-29
7.9 Attaching Mounting Brackets to the Module .......................................................................................... 7-31
7.9.1 Attachment of mounting brackets .................................................................................................... 7-31
7.9.2 Precautions for attaching mounting brackets .................................................................................. 7-32
7.10 Mounting the DIN Rail Adapter.............................................................................................................. 7-34
7.10.1 Specifications .................................................................................................................................. 7-34
7.10.2 Handling precautions ...................................................................................................................... 7-34
7.10.3 Attaching the DIN rail adapter to the module ................................................................................. 7-34
7.10.4 Mounting the module to a DIN rail .................................................................................................. 7-35
7.11 Common Terminal Block ....................................................................................................................... 7-37

8 TROUBLESHOOTING 8- 1 to 8-11
8.1 Verifying Errors from LED Status ........................................................................................................... 8- 1
8.2 Examples of Errors for Compact Remote I/O Modules ......................................................................... 8- 3
8.2.1 Errors occurring in the input circuit and corrective actions ............................................................. 8- 3
8.2.2 Errors occurring in the output circuit and corrective action............................................................. 8- 5

APPENDICES App- 1 to App-27

Appendix 1 External Dimensions...............................................................................................................App-1
Appendix 1.1 AJ65SBTB1-8 remote I/O module...............................................................................App-1
Appendix 1.2 AJ65SBTB1-16 remote I/O module.............................................................................App-2
Appendix 1.3 AJ65SBTW4-16 remote I/O module............................................................................App-4
Appendix 1.4 AJ65SBTB1-32 remote I/O module.............................................................................App-5
Appendix 1.5 AJ65SBTC1-32 , and AJ65SBTC4-16 remote I/O module......................................App-7
Appendix 1.6 AJ65SBTCF1-32 remote I/O module ..........................................................................App-9
Appendix 1.7 AJ65SBTB2-8 , AJ65SBTB3-8 , and AJ65SBTB32-8 remote I/O module.........App-10
Appendix 1.8 AJ65SBTB1B-16 ,AJ65SBTB2-16 , AJ65SBTB3-16 , and AJ65SBTB32-16
remote I/O module.........................................................................................................App-11
Appendix 1.9 AJ65SBTB2N-8 remote I/O module ..........................................................................App-12
Appendix 1.10 AJ65SBTB2N-16 remote I/O module........................................................................App-13
Appendix 1.11 AJ65VBTCU -8 , AJ65VBTCU -16 , and AJ65VBTCF1-32 remote I/O module
........................................................................................................................................App-14
Appendix 1.12 AJ65FBTA -16 remote I/O module .........................................................................App-17
Appendix 1.13 AJ65VBTS -16 , and AJ65VBTS -32 remote I/O module ................................App-18
Appendix 1.14 AJ65VBTCE -8 , AJ65VBTCE -16 , and AJ65VBTCE -32 remote I/O module
........................................................................................................................................App-20
Appendix 1.15 AJ65DBTB1-32 remote I/O module ........................................................................App-25
Appendix 1.16 AJ65SBTB1-32K , AJ65SBTB3-16KD, and AJ65SBTB32-16K remote I/O module
........................................................................................................................................App-26

A - 14 A - 14
ABOUT MANUALS

The following manuals are also related to this product.

In necessary, order them by quoting the details in the tables below.

Related Manuals

Manual Number
Manual Name
(Model Code)
CC-Link System Master/Local Module type AJ61BT11/A1SJ61BT11 User's Manual
IB-66721
This manual describes the system configuration, performance specification, function, handling, wiring
(13J872)
and troubleshooting for AJ61BT11 and A1SJ61BT11. (Sold separately)

CC-Link System Master/Local Module type AJ61QBT11/A1SJ61QBT11 User's Manual

IB-66722
This manual describes the system configuration, performance specification, function, handling, wiring
(13J873)
and troubleshooting for AJ61QBT11 and A1SJ61QBT11. (Sold separately)

CC-Link System Master/Local Module User's Manual

SH-080394
This manual describes the system configuration, performance specification, function, handling, wiring
(13JR64)
and troubleshooting for QJ61BT11N (Sold separately)

MELSEC-L CC-Link System Master/Local Module User's Manual

SH-080895ENG
Settings, specifications, handling, data communication methods, and troubleshooting of the built-in CC-
(13JZ41)
Link function of the CPU module or the CC-Link system master/local module (Sold separately)

COMPLIANCE WITH THE EMC AND LOW VOLTAGE DIRECTIVES

(1) Method of ensuring compliance

To ensure that Mitsubishi programmable controllers maintain EMC and Low Voltage Directives when
incorporated into other machinery or equipment, certain measures may be necessary. Please refer to
the "EMC AND LOW VOLTAGE DIRECTIVES" chapter in the user’s manual for the CPU module
used.
The CE mark on the side of the programmable controller indicates compliance with EMC and Low
Voltage Directives.

(2) Additional measures

To ensure that this product maintains EMC and Low Voltage Directives, please refer to the "CC-Link
module" section in the "EMC AND LOW VOLTAGE DIRECTIVES" chapter in the user’s manual for
the CPU module used.

A - 15 A - 15
 1 OVERVIEW
MELSEC-A

1 OVERVIEW
1 This manual describes the specifications of the compact remote I/O module
(hereinafter referred to as the "compact remote I/O module") used as the remote I/O
station of the CC-Link system.

1.1 Features

The following are the features of the compact remote I/O module:
(1) The remote I/O module is reduced in size yet retains all the
functions of the conventional module
The conventional remote I/O module has furthermore been reduced in size.
[External dimension (comparative example)]
Compact remote I/O module Conventional remote I/O module
AJ65SBTB1-16
AJ65SBTB2-8
AJ65SBTB1-32
Module AJ65SBTB2N-8
AJ65SBTB2-16
model AJ65SBTC1-32
AJ65SBTB1-8 AJ65SBTB2N-16 AJ65BTB1-16 AJ65BTB2-16 AJ65BTC1-32
name AJ65SBTC4-16
AJ65SBTB3-16
AJ65SBTCF1-32
AJ65SBTB32-16
AJ65SBTB3-8
AJ65SBTB32-8
Height 50 (1.97) 65 (2.56)
Width 87.3 (3.44) 118 (4.65) 179 (7.04) 151.9 (5.98) 197.5 (7.78) 165.0 (6.5)
Depth 40 (1.57) 46 (1.81)

Unit :mm (inch)

(2) More models in the compact remote I/O module lineup
The compact remote I/O modules for the CC-Link system is divided into six types
including terminal block type, one-touch connector type, waterproof-type, FCN
connector type, spring clamp terminal block type, and sensor connector (e-CON)
type.
In addition, the number of I/O points is divided into three types (8 points, 16
points, and 32 points), allowing the user to select a module that is most
appropriate for the environment and objective.

(3) 4-wire compact remote I/O module featuring easy connection of a

4-wire sensor
A 4-wire sensor can be easily connected via the common pin provided on each
plug without installing a relay terminal block.
For a 4-wire compact remote I/O module, one sensor is connected to each plug.
Therefore, sensors can be exchanged by plug, reducing work steps.

(4) Terminal block connection provides easy connection of 2-wire and

3-wire sensors or loads
Since the terminal block connection allows connection of 2-wire and 3-wire
sensors or loads, common connections are not needed and it makes connection
easier.

1-1 1-1
1 OVERVIEW
MELSEC-A

(5) Wiring work can be minimized

(a) Terminal-block module
The number of wiring steps can be dramatically reduced by adopting the use 1
of self-tightening screws on the terminal block.
(b) One-touch connector module, connector module
The number of wiring steps can be dramatically reduced by adopting use of
the pressure-displacement wire-connection method (soldering, peeling of
shield and screwing not necessary).
(c) FCN connector module
The number of wiring steps can be dramatically reduced by adopting 40-pin
connector for I/O part.
(d) Spring clamp terminal block module
The number of wiring steps can be dramatically reduced by adopting spring
clamps (screwing not necessary).

<Terminal-block module> <One-touch connector module, connector module>

Self-tightening
screw is used

Connector
Round solderless terminal
The round solderless terminal can
be connected simply by loosening
the screw on the terminal block.
Soldering, peeling of the shield
and screwing are unnecessary.

Each of the individual wires

Push in can be securely connected
simply by pressing the side
surface of the connector plug
after the wires are inserted
into the connector.

<FCN connector module>> <Spring clamp terminal block type >

FCN connector
Square shaped hole
Circular shaped hole

Tool

(6) Waterproof remote I/O modules with improved resistance against

water and oil
The waterproof remote I/O module, low profile waterproof remote I/O module
adopts a protection structure compatible with IP67, providing even safer usage in
areas in which water and oil are present.
1-2 1-2
1 OVERVIEW
MELSEC-A

(7) Up to a maximum of 64 remote I/O modules can be connected

In the CC-Link system, a maximum of 64 remote I/O modules can be connected
per master station.
Since each remote I/O module occupies 32 points, a maximum of 2048 link
points can be set.

(8) Modules can be exchanged without stopping the CC-Link system

With the adoption of a two-piece terminal block for the CC-Link cable connection,
modules may be exchanged without stopping the CC-Link system.

(9) Direct installation to the machine is feasible

The terminal-block remote I/O module may be installed directly to the machine,
since the charged area is protected by a finger protector in the upper area of the
terminal block.

(10) The module can be installed in six orientations

The compact remote I/O module can be installed in six different orientations.
(Restrictions may apply to some installation orientations.)
The module can also be installed using the DIN rail.

Ceiling installation

DIN rail Finger protector

Front installation

Horizontal installation

(11) Transistor output module with improved protection functions

The transistor output module is designed to achieve an even greater degree of
module protection by adopting overload protection, overheat protection and
overvoltage protection as standard. As a result, the programmable controller
system's reliability is further improved.

1-3 1-3
1 OVERVIEW
MELSEC-A

1.2 Identifying the Compact Remote I/O Module Type

The following shows how to identify the type of a compact remote I/O module:

AJ65 BT -
I/O specifications A: 100 V AC input
D,DN: 24 V DC input
(Positive/negative common shared type, or positive common input)
D5: 5 V DC input (Positive/negative common shared type)
R: Contact output module
S: Triac output
T : Transistor output
DE : 24 V DC input (Negative common input)
DTE : 24 V DC input (Negative common input), transistor output
(source output) combined
TE,TE1: Transistor output (Source output)
DT : 24 V DC input (Positive common input), transistor output
(sink output) combined
DR : 24 V DC input (Positive/negative common shared type),
contact output module
KD : With response speed switching function, 24V DC input
(Positive/negative common shared type)
KDT2 : With response speed switching function, 24V DC input
(Positive common input), transistor output (sink output)
combined
KDT8: With response speed switching function, 12V DC input
(Positive common input), transistor output (sink output)
combined
KDR: With response speed switching function, 24V DC input
(Positive/negative common shared type), contact output
module

Number of I/O points 8: 8 points

16 : 16 points
32 : 32 points
External load A2 : With 8 M12 waterproof connector, Output, 2-wire type.
connection method A4 : With 8 M12 waterproof connector, Input, 2 to 4-wire type.
A42 : With 8 M12 waterproof connector, Input, 2 to 4-wire type/
Output, 2-wire type.
B1 : 1-wire terminal block, 1-common type
B1B: 1-wire terminal block, 2-common type
B2,B2N:2-wire terminal block
B32 : Terminal Block, Input, 3-wire type/Output, 2-wire type.
C1 : 1-wire one-touch connector
C4 : 4-wire one-touch connector
CF1: 1-wire FCN connector
CFJ1: 1-wire FCN connector, common power supply type
CU2: 2-wire one-touch connector
CU3: 3-wire one-touch connector
W4: 4-wire waterproof connector
S2: 2-wire spring clamp terminal block
S3: 3-wire spring clamp terminal block
S32: Spring clamp terminal block, Input, 3-wire type/Output, 2-wire type.
CE2: 2-wire sensor connector(e-CON)
CE3: 3-wire sensor connector(e-CON)
CE32: Sensor connector(e-CON), Input, 3-wire type/Output, 2-wire type.

Cable specification T: Twisted cable(CC-Link dedicated cable)

Module type F: Low profile waterproof

S: Compact type
V: Connector type compact
D: A2C form

1-4 1-4
1 OVERVIEW
MELSEC-A

1.3 Precautions for use of remote I/O modules

This section describes the precautions for use of remote I/O modules applicable in the
CC-Link system and their specifications.
• This is a remote I/O module designed specifically for the CC-Link system.
Do not connect the module to other data-link systems, such as the
MELSECNET/MINI.
• 32 points are assigned per station for a compact remote I/O module.
For 16-point modules the 16 points in the second half and for 8-points module the 24
points in the second half remain empty but are not usable.
• Do not install the main circuit lines, high-voltage cables, and load cables other than
those connected to the programmable controller together.
If doing so, the remote I/O module (especially, AJ65SBTB1-16D1, AJ65SBTB1-
32D1, AJ65VBTCU3-8D1, AJ65VBTCU3-16D1, and AJ65SBTC1-32D1) will be
susceptible to noise, surge, and induction.
• When a mechanical contact, such as a relay, is connected to the AJ65SBTB1-16D1,
AJ65SBTB1-32D1, AJ65VBTCU3-8D1, AJ65VBTCU3-16D1, or AJ65SBTC1-32D1,
chattering may be input as a signal.

1.3.1 Input module

(1) Input response time and pulse width

The input module may take noise for inputs due to the signal pulse width.
The pulse width of the AJ65SBTB1-32KD , AJ65SBTB3-16KD , or
AJ65SBTB32-16KD is as shown in the following table depending on the
response speed set by the input response speed switching switch. In case of
setting the response speed, fully consider the operating environment.
Response speed setting Minimum value of pulse width that can take noise for inputs
value (ms) (ms)
0.2 0.006
1.5 0.8
5 3
10 6
When setting “0.2ms” as the response speed under an environment with noise, an
input signal line (including a common line) should be 3m or less.

1-5 1-5
1 OVERVIEW
MELSEC-A

(2) Precautions when using the DC input module

(a) Measures against back EMF
When an inductive load is connected, connect a diode to the load in parallel.
Use a diode that meets the following conditions.
• Reverse breakdown voltage is equal to or more than 10 times as large as the
circuit voltage.
• Forward current is equal to or more than 2 times as large as the load current.

IN IN

Inductive Inductive
load load

Diode Diode

COM COM

Positive common Negative common

(3) Precautions when using the AJ65SBTC1-32D or AJ65SBTC1-32D1

The maximum number of simultaneous input points of the AJ65SBTC1-32D or
AJ65SBTC1-32D1 varies depending on the ambient temperature.
Refer to the derating curve below

Derating curve for the AJ65SBTC1-32D or AJ65SBTC1-32D1

[%]

100
Maximum number of simultaneous input points

80

50

0
0 10 20 30 40 55 [ ]

Ambient temperature

1-6 1-6
1 OVERVIEW
MELSEC-A

(4) Precautions when using the AJ65VBTCF1-32DT1

The maximum number of simultaneous input points of the AJ65VBTCF1-32DT1
changes according to the installation orientation.
1) Installation orientations without limits
When the module is mounted as shown below, the maximum number of
simultaneous input points is not limited.

Vertical installation

2) Installation orientations with limits

When the module is mounted as shown below, the maximum number of
simultaneous input points is reduced to 60% at an ambient temperature of
55°C.
(Refer to the derating curve.)
Maximum number of simultaneous input points

100

Horizontal installation
60
50

0 10 20 30 40 45 55
Ambient temperature

Upward installation Downward installation Derating curve

1-7 1-7
1 OVERVIEW
MELSEC-A

(5) Precautions when using the AJ65VBTCFJ1-32DT1

The maximum number of simultaneous input points of the AJ65VBTCFJ1-32DT1
changes according to the installation orientation.
1) Vertical installation (basic)
When the module is mounted as shown below, the maximum number of
simultaneous input points is reduced to 65% at an ambient temperature of
55°C.
(Refer to the derating curve (1).)

Vertical installation (basic)

2) For installations other than front installation (basic orientation)

When the module is mounted as shown below, the maximum number of
simultaneous input points is reduced to 40% at an ambient temperature of
55°C.
(Refer to the derating curve (2).)

Vertical installation (upside down) Horizontal installation

Downward installation Upward installation

Maximum number of simultaneous
Maximum number of simultaneous

100 24.0VDC 100

80 26.4VDC

65 28.8VDC 65 24.0VDC
55 26.4VDC
40 28.8VDC
input points

input points

0 40 50 55 0 25 35 45 55
Ambient temperature Ambient temperature

Derating curve (1) Derating curve (2)

1-8 1-8
1 OVERVIEW
MELSEC-A

(6) Precautions when using the AJ65VBTS3-16D

The maximum number of simultaneous input points of the AJ65VBTS3-16D
changes according to the installation orientation.
1) Installation orientations without limits
When the module is mounted as shown below, the maximum number of
simultaneous input points is not limited.

J65VBT
S3-16

A
D

C
D

Vertical installation (basic)

2) Installation orientations with limits
When the module is mounted as shown below, the maximum number of
simultaneous input points is reduced to 75% at an ambient temperature of
55°C.
(Refer to the derating curve)

J65VBTS3-
J65VBT
16D S3-16D

Vertical installation (upside down) Horizontal installation (basic)

J65VBT
S3-16D

Horizontal installation (upside down) Upward installation

[ ]
100
simultaneous input points
Maximum number of

75

50

0 10 20 30 40 55 [ ]
Ambient temperature

Downward installation Derating curve

1-9 1-9
1 OVERVIEW
MELSEC-A

(7) Precautions when using the AJ65VBTS3-32D or AJ65VBTS32-32DT

The maximum number of simultaneous input points of the AJ65VBTS3-32D or
AJ65VBTS32-32DT changes according to the installation orientation.
1) Installation orientations without limits
When the module is mounted as shown below, the maximum number of
simultaneous input points is not limited.

J65VBT
S3-16
D

Vertical installation (basic)

2) Installation orientations with limits

When the module is mounted as shown below, the maximum number of
simultaneous input points of the AJ65VBTS3-32D is reduced to 69%
(11 points/common) at an ambient temperature of 55°C. (Refer to the derating
curve (1).)
That of the AJ65VBTS32-32DT is reduced to 75%. (Refer to the derating
curve (2).)

J65VBT J65VBT
S3-16D S3-16D

Vertical installation Horizontal installation Horizontal installation

(upside down) (basic) (upside down)

J65VBT
S3-16D

Downward installation Upward installation

[ ] [ ]
100 100
simultaneous input points

simultaneous input points

Maximum number of

Maximum number of

75 75
69
(11 points)

50 50

0 10 20 30 40 50 55 [ ] 0 10 20 30 40 50 55 [ ]
Ambient temperature Ambient temperature

Derating curve (1) Derating curve (2)

1 - 10 1 - 10
1 OVERVIEW
MELSEC-A

(8) Precautions when using the AJ65VBTCE3-16D or AJ65VBTCE3-16DE

The maximum number of simultaneous input points of the AJ65VBTCE3-16D or
AJ65VBTCE3-16DE changes according to the installation orientation.
1) Installation orientations without limits
When the module is mounted as shown below, the maximum number of
simultaneous input points is not limited.

J65V
BTS
3-1 6D

C
D

Vertical installation (basic)

2) Installation orientations with limits
When the module is mounted as shown below, the maximum number of
simultaneous input points is reduced to 62.5% at an ambient temperature of
55°C.
(Refer to the derating curve.)

J65V
BTS
3-1 6D

Vertical installation (upside down) Horizontal installation (basic)

Horizontal installation (upside down) Upward installation

100
simultaneous input points
Maximum number of

75
62.5

J65V
BTS
3-1 6D 50

0 10 20 30 40 50 55
Ambient temperature
Downward installation Derating curve

1 - 11 1 - 11
1 OVERVIEW
MELSEC-A

(9) Precautions when using the AJ65VBTCE3-32D or AJ65VBTCE3-32DE

The maximum number of simultaneous input points of the AJ65VBTCE3-32D or
AJ65VBTCE3-32DE changes according to the installation orientation.
1) Installation orientations without limits
When the module is mounted as shown below, the maximum number of
simultaneous input points is not limited.

J 6
5
VB
TS
3 -
6 D
1

Vertical installation (basic)

2) Installation orientations with limits
When the module is mounted as shown below, the maximum number of
simultaneous input points is reduced to 75% at an ambient temperature of
55°C.
(Refer to the derating curve.)

J65VBT
S3-16D

Vertical installation (upside down) Horizontal installation (basic)

Horizontal installation (upside down) Upward installation

[ ]
100
simultaneous input points

75
Maximum number of

50

0 10 20 30 40 50 55 [ ]
Ambient temperature
Downward installation Derating curve

1 - 12 1 - 12
1 OVERVIEW
MELSEC-A

(10) Precautions when using the AJ65SBTB1-32KD or AJ65SBTB1-32KDT2

The maximum number of simultaneous input points of the AJ65SBTB1-32KD or
AJ65SBTB1-32KDT2 changes according to the input voltage and ambient
temperature.
If the input voltage is higher than 26.4V, the maximum number of simultaneous
input points is as shown in the following figures.
(If the input voltage is 26.4V or lower, derating is not required.)

[ ] [ ]
100 100
simultaneous input points

simultaneous input points

Maximum number of

Maximum number of
75

50 50

0 10 20 30 40 50 55 [ ] 0 10 20 30 40 50 55 [ ]

Ambient temperature Ambient temperature

AJ65SBTB1-32KD derating curve AJ65SBTB1-32KDT2 derating curve

(11) Precautions when using a 3-wire or 4-wire module

When supplying power from a 3-wire or 4-wire module to an external device, such
as a sensor, total current must be equal to or less than the value of "supply current
for connected device" specified for the module.

1.3.2 Output module

(1) Maximum switching frequency when the module drives inductive load
The output must be on for one second or longer and off for one second or longer.
(2) Load for connection
When connecting a counter or timer that has a DC-DC converter to a transistor
output module (maximum load current 0.1A) as a load, select an output module
whose maximum load current is larger than inrush current of the load.
Selecting an output module by average current of the load may cause a failure of
the module because inrush current flows at a constant frequency at power-on or
during operation due to the connected load.
If an output module needs to be selected by average current of the load, take
either of the following actions to reduce an influence from inrush current.

Resistor Load Inductance Load

Output Output
module module

y Connecting a resistor to the load in series y Connecting an inductor to the load in series

1 - 13 1 - 13
1 OVERVIEW
MELSEC-A

(3) Precaution for using the transistor output module

(a) Action against reverse current
If a transistor output module is wired as shown below, reverse current flows in
an output element, causing a failure of the element.
When wiring a transistor output module, connect a diode as shown below.

• When connecting transistor output modules in parallel

Load Load
OUT1 OUT1

Load Load
OUT2 OUT2

COM COM

OUT1 OUT1

OUT2 OUT2

COM COM

Sink type Source type

• When incorporating an additional circuit parallel to a transistor output module

Additional circuit Additional circuit

OUT OUT
Diode Diode

COM COM

Sink type Source type

1 - 14 1 - 14
1 OVERVIEW
MELSEC-A

(b) Measures against back EMF

When an inductive load is connected, connect a diode to the load in parallel.
Use a diode that meets the following conditions.
• Reverse breakdown voltage is equal to or more than 10 times as large as the
circuit voltage.
• Forward current is equal to or more than 2 times as large as the load current.

Inductive Inductive
OUT load OUT load

Diode Diode

COM COM

Sink type Source type

(4) Modules that require an external short-circuit protection circuit

The following modules have no short-circuit protection function. Configure a short-
circuit protection circuit external to the programmable controller when they are
used.
• AJ65SBTB1-8T1 • AJ65SBTB2-8T1 • AJ65SBTB1-16T1 • AJ65SBTB2-16T1
• AJ65SBTB1B-16TE1 • AJ65VBTS2-16T • AJ65SBTB1-32T1 • AJ65SBTB1-32TE1
• AJ65DBTB1-32T1 • AJ65VBTS2-32T • AJ65SBTC1-32T1
• AJ65SBTB32-8DT2 • AJ65SBTB1-16DT2 • AJ65SBTB1-16DT3 • AJ65SBTB32-16DT2
• AJ65SBTB32-16KDT2 • AJ65SBTB32-16KDT8 • AJ65SBTB1-32DT2 • AJ65SBTB1-32KDT2
• AJ65SBTB1-32DT3 • AJ65SBTB1-32KDT8 • AJ65SBTB1-32DTE1 • AJ65DBTB1-32DT1
• AJ65VBTS32-16DT • AJ65VBTS32-32DT • AJ65SBTC4-16DT2 • AJ65SBTC1-32DT2
• AJ65SBTC1-32DT3

1 - 15 1 - 15
1 OVERVIEW
MELSEC-A

(5) Precautions when using a 3-wire module

When supplying power from a 3-wire module to an external device, such as a
sensor, the total current value must be equal to or less than the value of "supply
current for connected device" specified for the module.

(6) Precautions for using the contact output module

When using the contact output module, consider the following.
• Relay life
• Effects to relay life due to connected load
• Measures against back EMF
(a) Relay life
Applicable module: AJ65SBTB2N-8R, AJ65SBTB2N-16R,
AJ65DBTB1-32R, AJ65DBTB1-32DR
The relay life depends on the operating environment. Select a module
according to the operating environment. The relay lives shown below are the
actual service values, not the guaranteed values. Replace the module well
in advance since the actual switching life may be shorter than the one shown
below.

200

100

70

50
10000 times)

30

20
Service life (

100VDC to 120VDC
=7ms to 40ms
10
120VAC COS =1
7
240VAC COS =1
120VAC COS =0.4
5
240VAC COS =0.4
120VAC COS =0.3

30VDC =7ms
3
240VAC COS =0.3
(L/R) : Time constant
cos : Power factor 120VAC COS =0.2
2
240VAC COS =0.2

30VDC =40ms
1
0.1 0.2 0.3 0.5 0.7 1 2 3 5

Switching current (A)

Operating environment Switching life

Rated switching voltage/current, rated load 100 thousand times
200VAC 1.5A, 240VAC 1A (COS =0.7) 100 thousand times
200VAC 1A, 240VAC 0.5A (COS =0.35) 100 thousand times
24VDC 1A, 100VDC 0.1A (L/R=7ms) 100 thousand times

1 - 16 1 - 16
1 OVERVIEW
MELSEC-A

POINT
When using the module for the application in which the relay contact is frequently
switched, the relay life span should be considered. Therefore, it is recommended
to use a triac output module.

(b) Effects to relay life due to connected load

The actual relay life may be significantly shortened compared to the one
shown above, depending on the type of a load connected and the
characteristics of inrush current.
Also, the inrush current may cause contact welding.
Take the following measures to prevent shortening of the relay life and the
contact welding.
• Select a load so that the inrush current will be within the rated current of the
module.
• Connect an external relay that can withstand the inrush current.
The following table shows the relation between the road and the inrush current.
Select a load so that the inrush current (i) and the rated current (io) will be
within the rated switching current specified for the output module used.
The inrush current may flow for a longer time depending on the load.
Inrush current Inrush current
Load type Signal waveform diagram (i)/rated Signal waveform diagram (i)/rated
current (io) current (io)
Load of a solenoid Load of an electromagnetic contactor

i: Inrush current
i io Approx. 10 to io: Rated current
Approx. 3 to
Inductive load i io
20 times 10 times
i: Inrush current
io: Rated current 0.017 to 0.033 seconds
(1 to 2 cycles)
0.07 to 0.1 seconds
Load of an incandescent bulb Load of a mercury lamp

Approx. 3 to i io Approx. 3
i io *1
10 times i: Inrush current times
i: Inrush current
io: Rated current
io: Rated current
180 to 300 seconds
Approx. 0.33 seconds (3 to 5 minutes)
Lamp load
Load of a fluorescent

i io Approx. 5 to
⎯ ⎯
10 times
i: Inrush current
io: Rated current
Within 10 seconds
2
Capacitive load*

Capacitive Approx. 20 to
i io ⎯ ⎯
load 40 times
i: Inrush current
io: Rated current

0.008 to 0.33 seconds

(0.5 to 2 cycles)

1 - 17 1 - 17
1 OVERVIEW
MELSEC-A

(c) Measures against back EMF

Configure a contact protection circuit for extending the contact life, preventing
noise when the contact is cut off, and suppressing the generation of carbide
and nitric acid due to arc discharge.
An Incorrect contact protection circuit may cause contact welding.
Also, when using the contact protection circuit, the recovery time may be long.
The following table shows the representative examples of the contact
protection circuit.

Circuit example Method for selecting elements Remarks

Capacitor + Refer to the following for If a load is from a relay or

*1
Resistor method constants of the capacitor and solenoid, the recovery time
(CR method) resistor. Note that the following delays.
Capacitor
Inductive
values may differ depending A capacitor suppresses
Resistor
load on a nature of the load and a electric discharge while a
variation of characteristics of it. contact is off, and a resistor
• Capacitor 0.5 to 1 ( F) restricts a flow of current while
against contact current of 1A a contact is on.
• Resistor 0.5 to 1 (Ω) against
contact voltage of 1V
Capacitor
Inductive Use a capacitor whose
load
Resistor withstand voltage is 200 to
300V. In AC circuit, use a
capacitor having no polarity.
Diode method Use a diode that meets both The recovery time is later than
conditions shown below. the CR method.
• Reverse breakdown voltage
is equal to or more than 10
Inductive
Diode
load times as large as the circuit
voltage.
• The forward current is equal
to or more than 2 times as
large as the load current.
Diode + Zener Use zener voltage for the The diode method is effective
diode method zener diode equal to or more when the recovery time is too
Diode
Inductive than the power supply voltage. late.
load
Zener Diode

*1: When using AC power, impedance of CR must be larger enough than that
of the load. (prevention of a malfunction due to leak current from the CR)

(To the next page)

1 - 18 1 - 18
1 OVERVIEW
MELSEC-A

Circuit example Method for selecting elements Remarks

Varistor method Select a cut voltage (Vc) for The recovery time delays
the varistor to meet the slightly.
following condition.
• Vc > power voltage × 1.5(V)
• Vc > power voltage × 1.5(V) ×
√2 (When using AC power)
This method is not effective
when the Vc is too high

POINT
(1) Avoid providing contact protection circuits shown below.
These circuits are effective for preventing an arc at shut-off. However, the
contact welding may occur because the charge current flows to capacitor when
the contact turns on or off.
A DC inductive load is usually harder for switching than a resistor load, but if a
proper protection circuit is configured, the performance will be similar to the
resistor load.

Capacitor Inductive Capacitor Inductive

load load

(2) A protection circuit must be provided closely to a load or contact (module). If

their distance is far, the protection circuit may not be effective. Appropriate
distance is within 50cm.

1 - 19 1 - 19
1 OVERVIEW
MELSEC-A

1.3.3 Modules with protection functions

This section describes the protection functions of the following modules.

(1) Modules with overload protection function, overvoltage protection function, and
overheat protection function
AJ65SBTB1-8T, AJ65SBTB1-16T, AJ65SBTB1-32T, AJ65SBTB2-8T, AJ65SBTB2-16T,
Output module AJ65SBTC1-32T, AJ65SBTCF1-32T, AJ65VBTCU2-8T, AJ65VBTCU2-16T, AJ65VBTCE2-8T,
AJ65VBTCE2-16T
AJ65SBTB1-16DT, AJ65SBTB1-32DT, AJ65SBTB1-16DT1, AJ65SBTB1-32DT1,
AJ65SBTB32-8DT, AJ65SBTB32-16DT, AJ65SBTC4-16DT, AJ65SBTC1-32DT,
I/O combined module
AJ65SBTC1-32DT1, AJ65SBTW4-16DT, AJ65SBTCF1-32DT, AJ65VBTCF1-32DT1,
AJ65VBTCE32-16DT, AJ65VBTCE32-32DT
(2) Modules with overload protection function and overheat protection function
Output module AJ65SBTB1-8TE, AJ65SBTB1-16TE, AJ65FBTA2-16T, AJ65FBTA2-16TE,
AJ65VBTCE3-16TE
I/O combined module AJ65FBTA42-16DT, AJ65FBTA42-16DTE, AJ65VBTCE3-16DTE, AJ65VBTCE3-32DTE

Function Description
Common to protection functions 1. When an overcurrent continues to flow and generates overheat, overheat
protection is activated.
2. The functions are provided for protecting only the circuits inside the module.
A load error may deteriorate output elements or discolour the module case or
printed circuit board due to increase in temperature within the module. If a load
error occurs, turn off the corresponding output immediately and eliminate the error
cause.
Overload protection function 1. Protection is activated under an overload condition of 1 to 3A per point.
2. Protection is automatically reset when the load current drops to the rated value.
Overvoltage protection function 1. This function protects elements from an abrupt surge caused when a coil load is
used.
Overheat protection function 1. The protection of the following modules is activated in units of two points:
AJ65SBTB1-8TE, AJ65SBTB1-16TE, AJ65VBTCE3-16TE, AJ65VBTCE3-16DTE,
AJ65VBTCE3-32DTE
(For example, when protection is activated for either Y0 or Y1 output signals, Y0
and Y1 simultaneously turn off. When the overheat condition continues, the heat is
conducted to other loads and the corresponding protections may also be
activated.)
For the modules except the above, the protection is activated in units of one point.
2. If protection is activated while an output signal is on, the voltage oscillates
between 0V and the load voltage. When the load voltage is 24VDC, the average
voltage during oscillation is approximately 7VDC. (The voltage does not oscillate
when an output signal is off.)
Use an external load that operates at higher than 7VDC.
3. Protection is automatically reset when the temperature falls below the preset
value.

1 - 20 1 - 20
1 OVERVIEW
MELSEC-A

1.4 Specification List

Specification list for each compact remote I/O module is shown below.

(1) Input module

Operation Input response
No. of points

consumption
Input display
Rated input
per module

dimensions
Input current

Reference
Insulation

External
voltage time

method

voltage

Internal
current
Input External Common
Model
format connection connection
ON OFF OFF → ON →
voltage voltage ON OFF
8 points
AJ65SBTB1-8D 8 points Approx. 14V or 6V or 30mA 1 4.1.3
1.5ms or less 1 common
7mA more less
AJ65SBTB1-16D 35mA 4.1.5
16 points Approx. 15V or 3V or 2
AJ65SBTB1-16D1 0.2ms or less 16 points 40mA 4.1.6
5mA more less
1 common
Approx. 15V or 5V or
AJ65DBTB1-32D 10ms or less 1-wire 45mA 3 4.1.14
5mA more less
14V or 6V or terminal
AJ65SBTB1-32D DC input 1.5ms or less block 45mA 4.1.10
Approx. more less
(Positive/ 7mA 14V or 5.5V or
AJ65SBTB1-32KD 14 75mA 4.1.11
Negative more less
3
common) Approx. 15V or 3V or
AJ65SBTB1-32D1 32 points 0.2ms or less 50mA 4.1.12
5mA more less 32 points
Approx. 3.5V or 1.5V or 1 common
AJ65SBTB1-32D5 35mA 4.1.13
4mA more less
1.5ms or less
14V or 6V or 1-wire
AJ65SBTC1-32D 4.4.6
more less
one-touch 45mA
15V or 3V or
AJ65SBTC1-32D1 0.2ms or less connector 4.4.7
more less
AJ65SBTC4-16D 4.4.2
Photocoupler insulation

DC input 2
AJ65SBTC4-16DN (Positive 24VDC 4-wire 4.4.3
LED display

common) Approx. one-touch 35mA

DC input 16 points connector 16 points
5mA
AJ65SBTC4-16DE (Negative 14V or 6V or 1 common 4.4.4
common)
more less
4-wire
1.5ms or less waterproof
AJ65SBTW4-16D 120mA 4 4.6.3
connector
1-wire 32 points
DC input
AJ65SBTCF1-32D 32 points FCN 45mA 2 4.5.1
(Positive/ connector 1 common
negative 8 points
AJ65SBTB3-8D common) 8 points Approx. 14V or 6V or 40mA 2 4.1.4
1 common
7mA more less
AJ65SBTB3-16D 3-wire 45mA 4.1.7
Approx. 14V or 5.5V or terminal
AJ65SBTB3-16KD 14 16 points 50mA 4.1.8
16 points 7mA more less block 3
1 common
Approx. 3.5V or 1.5V or
AJ65SBTB3-16D5 1.5ms or less 30mA 4.1.9
4mA more less
3-wire 8 points
AJ65VBTCU3-8D1 DC input 8 points 35mA 5 4.4.1
Approx. 15V or 3V or 1 common
(Positive 0.2ms or less one-touch
5mA more less 16 points
AJ65VBTCU3-16D1 common) 16 points connector 40mA 6 4.4.5
1 common
8 points
AJ65SBTB2N-8A 8 points 100 to 2-wire 35mA 2 4.1.1
Approx. 80V or 30V or 1 common
AC input 120VAC 20ms or less terminal
7mA more less 16 points
AJ65SBTB2N-16A 16 points 50/60Hz block 40mA 3 4.1.2
1 common

1 : 87.3 (3.44) (W) × 50 (1.97) (H) × 40 (1.57) (D)mm (inch) 8 : 137 (5.39) (W) × 50 (1.97) (H) × 51.5 (2.03) (D)mm (inch)
2 : 118 (4.65) (W) × 50 (1.97) (H) × 40 (1.57) (D)mm (inch) 9 : 222 (8.74) (W) × 50 (1.97) (H) × 51.5 (2.03) (D)mm (inch)
3 : 179 (7.05) (W) × 50 (1.97) (H) × 40 (1.57) (D)mm (inch) 10 : 100 (3.94) (W) × 40 (1.57) (H) × 43.5 (1.71) (D)mm (inch)
4 : 184.7 (7.27) (W) × 57.9 (2.28) (H) × 86 (3.39) (D)mm (inch) 11 : 100 (3.94) (W) × 50 (1.97) (H) × 45.5 (1.79) (D)mm (inch)
5 : 41 (1.61) (W) × 115 (4.53) (H) × 62 (2.44) (D)mm (inch) 12 : 155 (6.10) (W) × 50 (1.97) (H) × 45.5 (1.79) (D)mm (inch)
6 : 60 (2.36) (W) × 115 (4.53) (H) × 62 (2.44) (D)mm (inch) 13 : 64 (2.52) (W) × 170 (6.70) (H) × 80 (3.15) (D)mm (inch)
7 : 60 (2.36) (W) × 200 (7.87) (H) × 48 (1.89) (D)mm (inch) 14 : 0.2ms or less/1.5ms or less/5ms or less/10ms or less
(Depending on the input response speed setting value)

1 - 21 1 - 21
1 OVERVIEW
MELSEC-A

Operation Input response

No. of points

consumption
Input display
Rated input
per module

dimensions
Input current

Reference
Insulation

External
voltage time

method

voltage

Internal
current
Input External Common
Model
format connection connection
ON OFF OFF → ON →
voltage voltage ON OFF
DC input
AJ65FBTA4-16D (Positive 2 to 4-wire 4.6.1
common) Approx.
waterproof 40mA 7
DC input 16 points 7mA
connector
AJ65FBTA4-16DE (Negative 4.6.2
common) 16 points
1 common
AJ65VBTS3-16D Spring 35mA 8 4.2.1
clamp
terminal
Photocoupler insulation

AJ65VBTS3-32D 32 points block 40mA 9 4.2.2

3-wire type

LED display
DC input 14V or 6V or
24VDC 1.5ms or less 8 points
AJ65VBTCE3-8D (Positive 8 points 30mA 10 4.3.1
more less 1 common
common)
Approx. 16 points
AJ65VBTCE3-16D 16 points 35mA 11 4.3.2
5mA 1 common
Sensor
connector 32 points
AJ65VBTCE3-32D 32 points (e-CON) 40mA 12 4.3.3
1 common
3-wire type
16 points
AJ65VBTCE3-16DE DC input 16 points 35mA 11 4.3.4
1 common
(Negative
32 points
AJ65VBTCE3-32DE common) 32 points 40mA 12 4.3.5
1 common

1 : 87.3 (3.44) (W) × 50 (1.97) (H) × 40 (1.57) (D)mm (inch) 8 : 137 (5.39) (W) × 50 (1.97) (H) × 51.5 (2.03) (D)mm (inch)
2 : 118 (4.65) (W) × 50 (1.97) (H) × 40 (1.57) (D)mm (inch) 9 : 222 (8.74) (W) × 50 (1.97) (H) × 51.5 (2.03) (D)mm (inch)
3 : 179 (7.05) (W) × 50 (1.97) (H) × 40 (1.57) (D)mm (inch) 10 : 100 (3.94) (W) × 40 (1.57) (H) × 43.5 (1.71) (D)mm (inch)
4 : 184.7 (7.27) (W) × 57.9 (2.28) (H) × 86 (3.39) (D)mm (inch) 11 : 100 (3.94) (W) × 50 (1.97) (H) × 45.5 (1.79) (D)mm (inch)
5 : 41 (1.61) (W) × 115 (4.53) (H) × 62 (2.44) (D)mm (inch) 12 : 155 (6.10) (W) × 50 (1.97) (H) × 45.5 (1.79) (D)mm (inch)
6 : 60 (2.36) (W) × 115 (4.53) (H) × 62 (2.44) (D)mm (inch) 13 : 64 (2.52) (W) × 170 (6.70) (H) × 80 (3.15) (D)mm (inch)
7 : 60 (2.36) (W) × 200 (7.87) (H) × 48 (1.89) (D)mm (inch) 14 : 0.2ms or less/1.5ms or less/5ms or less/10ms or less
(Depending on the input response speed setting value)

1 - 22 1 - 22
1 OVERVIEW
MELSEC-A

(2) Output module

No. of points
Maximum load Output response

consumption

dimensions
per module

suppressor

Reference
Insulation

External
method

voltage

Internal
display
Output

current
Surge
Rated
Output current time External Common

load
Model
format OFF → ON → connection connection
1 point 1 common
ON OFF
8 points
AJ65SBTB1-8T 8 points 2.4 A 35mA 1 5.1.1
1-wire 1 common
0.5 A terminal 16 points
AJ65SBTB1-16T Transistor 16 points 3.6 A 50mA 2 5.1.5
block 1 common
output 14
AJ65SBTB1-32T 4.8 A 65mA 3 5.1.9
(sink type)
1-wire 32 points
32 points
AJ65SBTC1-32T 0.1 A 3.2 A one-touch 1 common 60mA 2 5.4.3
connector
8 points
AJ65SBTB1-8T1 8 points 2.4 A 35mA 1 5.1.2
1 common
1-wire
16 points
AJ65SBTB1-16T1 16 points 0.5 A 3.6 A terminal 50mA 2 5.1.6
Transistor 1 common
block
AJ65DBTB1-32T1 output 13 8A 65mA 12 5.1.19
Photocoupler insulation

AJ65SBTB1-32T1 (sink type) 4.8 A 65mA 3 5.1.10

32 points
32 points 1-wire
1 common
AJ65SBTC1-32T1 12/24 0.1 A 3.2 A 0.5ms 1.5ms Zener one-touch 60mA 2 5.4.4
VDC or less or less diode connector
8 points
AJ65SBTB1-8TE 8 points 0.8 A 35mA 1 5.1.11
1 common
0.1 A
16 points
AJ65SBTB1-16TE Transistor 16 points 1.6 A 1-wire 50mA 2 5.1.12
1 common
output 13 terminal 8 points
AJ65SBTB1B- LED display
16TE1 (source type) 16 points 4A block 1 common
50mA 3 5.1.13
0.5 A
AJ65SBTB1- 32 points
32 points 4.8A 65mA 3 5.1.14
32TE1 1 common
8 points
AJ65SBTB2-8T Transistor 8 points 2.4 A 45mA 2 5.1.3
1 common
output 14 0.5 A
16 points
AJ65SBTB2-16T (sink type) 16 points 3.6 A 55mA 3 5.1.7
1 common
8 points
AJ65SBTB2-8T1 Transistor 8 points 2.4 A 45mA 2 5.1.4
1 common
output 12 0.5 A 2-wire
16 points
AJ65SBTB2-16T1 (sink type) 16 points 3.6 A terminal 55mA 3 5.1.8
1 common
block
Relay insulation

8 points
AJ65SBTB2N-8R 8 points 4A 85mA 2 5.1.15
1 common

Contact 24VDC 10ms or 12ms or 16 points

AJ65SBTB2N-16R 16 points 2A 8A None 120mA 3 5.1.16
output 240VAC less less 1 common

1-wire
Photocoupler insulation

AJ65DBTB1-32R 32 points 4A terminal 80mA 12 5.1.20

block 8 points
1 common
AJ65SBTB2N-8S 8 points 2.4 A 1ms + 55mA 2 5.1.17
100 to 2-wire
Triac output 1ms 0.5 CR
240VAC 0.6 A terminal
16 or less cycle or Absorber
50/60Hz block 32 points
AJ65SBTB2N-16S 16 points 4.8 A less 85mA 3 5.1.18
1 common

1 : 87.3 (3.44) (W) × 50 (1.97) (H) × 40 (1.57) (D)mm (inch) 10 : 100 (3.94) (W) × 40 (1.57) (H) × 43.5 (1.71)(D)mm (inch)
2 : 118 (4.65) (W) × 50 (1.97) (H) × 40 (1.57) (D)mm (inch) 11 : 100 (3.94) (W) × 50 (1.97) (H) × 45.5 (1.79) (D)mm (inch)
3 : 179 (7.05) (W) × 50 (1.97) (H) × 40 (1.57) (D)mm (inch) 12 : 64 (2.52) (W) × 170 (6.70) (H) × 80 (3.15) (D)mm (inch)
4 : 184.7 (7.27) (W) × 57.9 (2.28) (H) × 86 (3.39) (D)mm (inch) 13 : Leakage current when the transistor output is OFF (0.1mA or less)
5 : 41 (1.61) (W) × 115 (4.53) (H) × 62 (2.44) (D)mm (inch) 14 : Leakage current when the transistor output is OFF (0.25mA or less)
6 : 60 (2.36) (W) × 115 (4.53) (H) × 62 (2.44) (D)mm (inch) 15 : Leakage current when the transistor output is OFF (0.3mA or less)
7 : 60 (2.36) (W) × 200 (7.87) (H) × 48 (1.89) (D)mm (inch) 16 : Leakage current when the triac output is OFF 1.5mA rms or less
8: 137 (5.39) (W) × 50 (1.97) (H) × 51.5 (2.03) (D)mm (inch) (100VAC rms 60Hz), 3mA rms or less (200VAC rms 60Hz)
9: 222 (8.74) (W) × 50 (1.97) (H) × 51.5 (2.03) (D)mm (inch)

1 - 23 1 - 23
1 OVERVIEW
MELSEC-A

No. of points
Maximum load Output response

consumption

dimensions
per module

suppressor

Reference
Insulation

External
method

voltage

Internal
display
Output

current
Surge
Rated
Output current time External Common

load
Model
format OFF → ON → connection connection
1 point 1 common
ON OFF
0.5ms 1.5ms 1-wire FCN 32 points
AJ65SBTCF1-32T 32 points 3.2 A 60mA 2 5.5.1
Transistor or less or less connector 1 common
output 13 0.1 A 2-wire 8 points
AJ65VBTCU2-8T 8 points 0.8 A 1ms 1ms 35mA 5 5.4.1
(sink type) one-touch 1 common
or less or less
AJ65VBTCU2-16T 1.6 A connector 40mA 6 5.4.2
Transistor
AJ65FBTA2-16T output 14 0.5 A 2-wire 50mA 7 5.6.1
(sink type) 0.5ms 1.5ms
16 points waterproof
Transistor
Photocoupler insulation

or less or less
connector 16 points
AJ65FBTA2-16TE output 15 1.0 A 50mA 7 5.6.2
1 common

LED display
(source type) 4.0 A
AJ65VBTS2-16T 12/24 Zener Spring 45mA 8 5.2.1
VDC diode clamp
0.5 A terminal
AJ65VBTS2-32T Transistor 32 points block 60mA 9 5.2.2
output 12 2-wire type
(sink type) Sensor 8 points
AJ65VBTCE2-8T 8 points 0.8 A 1ms 1ms connector 35mA 5.3.1
1 common 10
or less or less (e-CON)
AJ65VBTCE2-16T 2-wire type 5.3.2
0.1 A
Sensor 16 points
Transistor 16 points 1.6 A 45mA
AJ65VBTCE3- connector 1 common 11
output 13 5.3.3
16TE (e-CON)
(source type)
3-wire type

1 : 87.3 (3.44) (W) × 50 (1.97) (H) × 40 (1.57) (D)mm (inch) 10 : 100 (3.94) (W) × 40 (1.57) (H) × 43.5 (1.71)(D)mm (inch)
2 : 118 (4.65) (W) × 50 (1.97) (H) × 40 (1.57) (D)mm (inch) 11 : 100 (3.94) (W) × 50 (1.97) (H) × 45.5 (1.79) (D)mm (inch)
3 : 179 (7.05) (W) × 50 (1.97) (H) × 40 (1.57) (D)mm (inch) 12 : 64 (2.52) (W) × 170 (6.70) (H) × 80 (3.15) (D)mm (inch)
4 : 184.7 (7.27) (W) × 57.9 (2.28) (H) × 86 (3.39) (D)mm (inch) 13 : Leakage current when the transistor output is OFF (0.1mA or less)
5 : 41 (1.61) (W) × 115 (4.53) (H) × 62 (2.44) (D)mm (inch) 14 : Leakage current when the transistor output is OFF (0.25mA or less)
6 : 60 (2.36) (W) × 115 (4.53) (H) × 62 (2.44) (D)mm (inch) 15 : Leakage current when the transistor output is OFF (0.3mA or less)
7 : 60 (2.36) (W) × 200 (7.87) (H) × 48 (1.89) (D)mm (inch) 16 : Leakage current when the triac output is OFF 1.5mA rms or less
8: 137 (5.39) (W) × 50 (1.97) (H) × 51.5 (2.03) (D)mm (inch) (100VAC rms 60Hz), 3mA rms or less (200VAC rms 60Hz)
9: 222 (8.74) (W) × 50 (1.97) (H) × 51.5 (2.03) (D)mm (inch)

1 - 24 1 - 24
1 OVERVIEW
MELSEC-A

(3) Combined I/O module

In the combined I/O module, the input side and the output side are structure as a pair.
(a) Input side

No. of points

Input current
Operation Input response

consumption
Input display
Rated input
per module

dimensions

Reference
Insulation

External
Division

voltage time

method

voltage

Internal
current
Input External Common
Model
format connection connection
ON OFF OFF → ON →
voltage voltage ON OFF

AJ65SBTC1-32DT 14V or 6V or 1.5ms or less

more less 6.4.3

AJ65SBTC1-32DT1 15V or 3V or 0.2ms or less 32 points

more less 1-wire 6.4.4
16 1 common
one-touch 50mA
points 14V or 6V or (shared with
AJ65SBTC1-32DT2 1.5ms or less connector output)
more less 1 6.4.5

AJ65SBTC1-32DT3 15V or 3V or 0.2ms or less

Approx. more less 6.4.6
5mA
AJ65SBTC4-16DT 4-wire 6.4.1
one-touch 16 points 40mA
AJ65SBTC4-16DT2 8 connector 1 common 6.4.2
points 4-wire (shared with
AJ65SBTW4-16DT DC input waterproof output) 90mA 3 6.6.3
(Positive 14V or 6V or 1.5ms or less connector
common) more less 16 points
8
AJ65SBTB1-16DT 1 common (shared 50mA 1 6.1.3
points
Approx. with output)
7mA 32 points
16
AJ65SBTB1-32DT 1 common (shared 32mA 2 6.1.13
points with output)
24
8 VDC 16 points
AJ65SBTB1-16DT1 1 common (shared 55mA 1 6.1.4
points with output)
3V or
0.2ms or less
Approx. 15V or less 32 points
AJ65SBTB1-32DT1 5mA more 1 common (shared 60mA 2 6.1.14
Photocoupler insulation

with output)
16 5V or 16 points
AJ65DBTB1-32DT1 10ms or less 55mA 5 6.1.20
LED display

points less 1 common

Input side

1-wire
DC input terminal 32 points
AJ65SBTB1-32DTE1 (Negative 1 common (shared 50mA 2 6.1.19
common) block with output)
6V or 1.5ms or less 16 points
8 Approx. 14V or less
AJ65SBTB1-16DT2 1 common (shared 50mA 1 6.1.5
points 7mA more with output)
AJ65SBTB1-32DT2 32 points 60mA 6.1.15
16
5.5V or 1 common (shared 2
AJ65SBTB1-32KDT2 points 11 65mA
less with output) 6.1.16

8 16 points
AJ65SBTB1-16DT3 Approx. 15V or 3V or 1 common (shared 55mA 1 6.1.6
points 0.2ms or less
5mA more less with output)
AJ65SBTB1-32DT3 32 points 60mA 6.1.17
16
12 Approx. 5.6V or 2.4V or 1 common (shared 2
AJ65SBTB1-32KDT8 points 11 65mA
VDC 11mA more less with output) 6.1.18
DC input
(Positive 8 points
4
AJ65SBTB32-8DT common) points 1 common (shared 45mA 1 6.1.1
with output)
8 16 points
AJ65SBTB32-16DT 6V or 1 common (shared 50mA 2 6.1.7
points 1.5ms or less Input 3-wire with output)
24 Approx. 14V or less
Output 8 points
4 VDC 7mA more
AJ65SBTB32-8DT2 2-wire 1 common (shared 45mA 1 6.1.2
points terminal with output)
AJ65SBTB32-16DT2 block 50mA 6.1.8
8 5.5V or 16 points
AJ65SBTB32-16KDT2 less 11 1 common (shared 55mA 2 6.1.9
points
12 Approx. 5.6V or 2.4V or with output)
AJ65SBTB32-16KDT8 11 55mA 6.1.10
VDC 11mA more less

1 : 118 (4.65) (W) × 50 (1.97) (H) × 40 (1.57) (D)mm (inch) 7 : 137 (5.39) (W) × 50 (1.97) (H) × 51.5 (2.03) (D)mm (inch)
2 : 179 (7.05) (W) × 50 (1.97) (H) × 40 (1.57) (D)mm (inch) 8 : 222 (8.74) (W) × 50 (1.97) (H) × 51.5 (2.03) (D)mm (inch)
3 : 184.7 (7.27) (W) × 57.9 (2.28) (H) × 86 (3.39) (D)mm (inch) 9 : 100 (3.94) (W) × 50 (1.97) (H) × 41.5 (1.63) (D)mm (inch)
4 : 41 (1.61) (W) × 115 (4.53) (H) × 67 (2.64) (D)mm (inch) 10 : 155 (6.10) (W) × 50 (1.97) (H) × 45.5 (1.79) (D)mm (inch)
5 : 64 (2.52) (W) × 170 (6.70) (H) × 80 (3.15) (D)mm (inch) 11 : 0.2ms or less/1.5ms or less/5ms or less/10ms or less
6 : 60 (2.36) (W) × 200 (7.87) (H) × 48 (1.89) (D)mm (inch) (Depending on the input response speed setting value)

1 - 25 1 - 25
1 OVERVIEW
MELSEC-A

No. of points

Input current
Operation Input response

consumption
Input display
Rated input
per module

dimensions

Reference
Insulation

External
Division

voltage time

method

voltage

Internal
current
External Common
Model Input format
connection connection
ON OFF OFF → ON →
voltage voltage ON OFF
6V or Input
AJ65SBTB32-16DR 1.5ms or less 3-wire 85mA 6.1.11
less
8 Approx. 14V or Output 8 points
2
AJ65SBTB32- points 7mA more 5.5V or 2-wire 1 common
11 terminal 100mA 6.1.12
16KDR DC input less
block
(Positive/
negative 1-wire
15V or 5V or
AJ65DBTB1-32DR common) 10ms or less terminal 60mA 5 6.1.21
more less
block
16 Approx. 14V or 6V or 16 points
AJ65SBTCF1-32DT 1.5ms or less 1 6.5.1
points 5mA more less 1 common
1-wire
AJ65VBTCF1-32DT1 one-touch 4 6.5.2
15V or 3V or 0.2ms or less connector
AJ65VBTCFJ1- 50mA
more less 6.5.3
32DT1 DC input
Photocoupler insulation

(Positive
AJ65FBTA42-16DT common) 6.6.1
2 to 4-wire 8 points 6

LED display
Approx.
waterproof 1 common (Shared
Input side

DC input 24 7mA
AJ65FBTA42-16DTE (Negative 8 connector with output) 45mA 6.6.2
points VDC
common)
Spring 16 points
AJ65VBTS32-16DT clamp 1 common (shared 40mA 7 6.2.1
terminal with output)
16 block 16 points
AJ65VBTS32-32DT 3-wire type 50mA 8 6.2.2
DC input points 1 common
(Positive 14V or 6V or 16 points
8 more less 1.5ms or less
AJ65VBTCE32-16DT common) 1 common (shared 40mA 9 6.3.1
points
Approx. with output)
16 5mA 32 points
AJ65VBTCE32-32DT points Sensor 1 common (shared 45mA 10 6.3.3
connector with output)
(e-CON) 16 points
8 3-wire type 1 common (shared
AJ65VBTCE3-16DTE 40mA 9 6.3.2
DC input points
with output)
(Negative
common) 16 32 points
AJ65VBTCE3-32DTE points 1 common (shared 45mA 10 6.3.4
with output)

1 : 118 (4.65) (W) × 50 (1.97) (H) × 40 (1.57) (D)mm (inch) 7 : 137 (5.39) (W) × 50 (1.97) (H) × 51.5 (2.03) (D)mm (inch)
2 : 179 (7.05) (W) × 50 (1.97) (H) × 40 (1.57) (D)mm (inch) 8 : 222 (8.74) (W) × 50 (1.97) (H) × 51.5 (2.03) (D)mm (inch)
3 : 184.7 (7.27) (W) × 57.9 (2.28) (H) × 86 (3.39) (D)mm (inch) 9 : 100 (3.94) (W) × 50 (1.97) (H) × 41.5 (1.63) (D)mm (inch)
4 : 41 (1.61) (W) × 115 (4.53) (H) × 67 (2.64) (D)mm (inch) 10 : 155 (6.10) (W) × 50 (1.97) (H) × 45.5 (1.79) (D)mm (inch)
5 : 64 (2.52) (W) × 170 (6.70) (H) × 80 (3.15) (D)mm (inch) 11 : 0.2ms or less/1.5ms or less/5ms or less/10ms or less
6 : 60 (2.36) (W) × 200 (7.87) (H) × 48 (1.89) (D)mm (inch) (Depending on the input response speed setting value)

1 - 26 1 - 26
1 OVERVIEW
MELSEC-A

(b) Output side

Internal current
Output display
Maximum load Output

No. of points

consumption

dimensions
per module

suppressor
Rated load

Reference
Insulation

External
current response time
Division

method

voltage

Surge
Output External Common
Model
format connection connection
OFF → ON →
1 point 1 common
ON OFF

AJ65SBTC1-32DT Transistor
output 13
AJ65SBTC1-32DT1 (sink type) 1-wire 32 points
16
0.1A 1.6A one-touch 1 common
Transistor points
AJ65SBTC1-32DT2 connector (shared with input)
output 12
AJ65SBTC1-32DT3 (sink type)
Transistor
AJ65SBTC4-16DT output 13
(sink type) 4-wire
one-touch
Transistor connector 16 points
8
AJ65SBTC4-16DT2 output 12 points 1 common
(shared with input)
(sink type) 24 2.4A
VDC 4-wire
AJ65SBTW4-16DT waterproof
connector
16 points
8
AJ65SBTB1-16DT 1 common (shared
points
with input)
Transistor 32 points
16
AJ65SBTB1-32DT output 13 points 3.6A 1 common (shared
(sink type) with input)
16 points
8
AJ65SBTB1-16DT1 2.4A 1 common
points
(shared with input)
32 points
AJ65SBTB1-32DT1 3.6A 1 common
(shared with input)
Photocoupler insulation

Transistor
12/24 16 points
AJ65DBTB1-32DT1 output 12 16 4A
VDC 1 common
LED display

(sink type) points

Output side

1-wire
Transistor 0.5ms 1.5ms Zener terminal
32 points See input side
or less or less diode block
AJ65SBTB1-32DTE1 output 12 3.6A 1 common
(source (shared with input)
type)
0.5A 16 points
8
AJ65SBTB1-16DT2 2.4A 1 common
points
24 (shared with input)
AJ65SBTB1-32DT2 VDC 32 points
16
3.6A 1 common
AJ65SBTB1-32KDT2 Transistor points (shared with input)
output 12 16 points
(sink type) 8
AJ65SBTB1-16DT3 2.4A 1 common
points
(shared with input)
AJ65SBTB1-32DT3 32 points
16
12 3.6A 1 common
AJ65SBTB1-32KDT8 points
VDC (shared with input)
8 points
4
AJ65SBTB32-8DT Transistor points 1.2A 1 common
(shared with input)
output 13
16 points
(sink type) 8
AJ65SBTB32-16DT 2.4A 1 common
points
(shared with input)
24 Input 3-wire 8 points
4
AJ65SBTB32-8DT2 VDC 1.2A Output 1 common
points
2-wire (shared with input)
terminal
AJ65SBTB32-16DT2 Transistor block
output 12
16 points
8
AJ65SBTB32-16KDT2 (sink type) points 2.4A 1 common
(shared with input)
12
AJ65SBTB32-16KDT8
VDC

12 : Leakage current when the transistor output is OFF (0.1mA or less)

13 : Leakage current when the transistor output is OFF (0.25mA or less)
14 : Leakage current when the transistor output is OFF (0.3mA or less)

1 - 27 1 - 27
1 OVERVIEW
MELSEC-A

Internal current
Output display
Maximum load Output

No. of points

consumption

dimensions
per module

suppressor
Rated load

Reference
Insulation

External
current response time
Division

method

voltage

Surge
External Common
Model Output format
connection connection
OFF → ON →
1 point 1 common
ON OFF
Input 3-wire
AJ65SBTB32-16DR

insulation
8 Output 4 points

Relay
24 2-wire
points 1 common
AJ65SBTB32-16KDR Contact output VDC 10ms 12ms terminal
2A 4A None
240 or less or less block
VAC 1-wire 8 points
16
AJ65DBTB1-32DR terminal
points 1 common
block
AJ65SBTCF1-32DT 0.5ms 1.5ms
12/24 or less or less
Transistor 1-wire
16 VDC 16 points
AJ65VBTCF1-32DT1 output 12 points 0.1A 1.6A FCN
1ms 1ms 1 common
(sink type) connector
AJ65VBTCFJ1- or less or less
32DT1
Transistor
AJ65FBTA42-16DT output 13 0.5A 2.4A
(sink type) 2-wire 8 points
24 0.5ms 1.5ms
waterproof 1 common

LED display
Output side

or less or less
Photocoupler insulation

Transistor 8 VDC connector (shared with input)

AJ65FBTA42-16DTE output 14 points 1.0A
See input side
(source type)
4.0A Spring 16 points
AJ65VBTS32-16DT Zener clamp 1 common
0.5A diode terminal (shared with input)
16 12/24 block 16 points
AJ65VBTS32-32DT Transistor 2-wire type
points VDC 1 common
output 12 16 points
8
AJ65VBTCE32-16DT (sink type) 0.8A Sensor 1 common
points
1ms 1ms connector (shared with input)
or less or less (e-CON) 32 points
16 2-wire type
AJ65VBTCE32-32DT 1.6A 1 common
points
24 (shared with input)
0.1A
VDC 16 points
8
AJ65VBTCE3-16DTE Transistor 0.8A Sensor 1 common
points
connector (shared with input)
output 12 (e-CON) 32 points
16
AJ65VBTCE3-32DTE (source type) 1.6A 3-wire type 1 common
points
(shared with input)

12 : Leakage current when the transistor output is OFF (0.1mA or less)

13 : Leakage current when the transistor output is OFF (0.25mA or less)
14 : Leakage current when the transistor output is OFF (0.3mA or less)

1 - 28 1 - 28
1 OVERVIEW
MELSEC-A

1.5 Parts Sold Separately

The plugs for one-touch connector module are sold separately.

Please purchase them as necessary.
Mitsubishi model Part model name Color of
Specifications
name (manufacturer) the cover
Applicable cable Maximum
Applicable cable core size
outer diameter rated
(mm2)
(mm) current (A)
33104-6000FL
A6CON-P214 φ 1.0 to 1.4 Transparent
Plug for (3M) 0.14 to 0.2
2
one-touch connector 33104-6100FL (AWG26 to 24)
A6CON-P220 φ 1.4 to 2.0 Yellow
1 (3M)
33104-6200FL
A6CON-P514 φ 1.0 to 1.4 Red
(3M) 0.3 to 0.5
3
33104-6300FL (AWG22 to 20)
A6CON-P520 φ 1.4 to 2.0 Blue
(3M)
communication 0.5
One-touch φ 2.2 to 3.0
35505-6000- line (AWG20)
connector for A6CON-L5P Red
BOM GF (3M) 0.5
communication 2 shielded cable
(AWG20)
One-touch 35505-6080-A00 0.75 (0.66 to 0.98) (AWG18)
A6CON-PW5P φ 2.2 to 3.0 Gray
connector for power GF (3M) wire diameter 0.16mm or more
7
supply and FG A6CON-PW5P- 35505-6180-A00 Outer insulation layer material:
2 4 PVC (Heat-resistant vinyl) φ 2.0 to 2.3 Blue
SOD GF(3M)
Dustproof cap 1 A6CAP-DC1 ⎯ (AJ65SBTW -16 only) ⎯ ⎯
Protection construction : IP67
A6CAP-WP1 ⎯ ⎯ ⎯
(AJ65SBTW -16 only)
Waterproof cap 1
Protection of degree : IP67
A6CAP-WP2 ⎯ ⎯ ⎯
(AJ65FBTA -16 only)
A6CON1 ⎯ Soldering type (Straight-out type) ⎯ ⎯
A6CON2 ⎯ Crimp-contact type (Straight-out type) ⎯ ⎯
FCN connector
A6CON3 ⎯ Pressure-displacement type (Flat cable type) ⎯ ⎯
A6CON4 ⎯ Soldering type (Straight-out/diagonal-out type) ⎯ ⎯
Online connector for 35720-L200-B00
A6CON-LJ5P ⎯ ⎯ ⎯ ⎯ ⎯
communication 3 AK (3M)
Online connector for 35720-L200-A00
A6CON-PWJ5P ⎯ ⎯ ⎯ ⎯ ⎯
power supply 3 AK (3M)
Terminal resister
One-touch connector plug with
attached one-touch
A6CON-TR11 ⎯ terminal resister attached for ⎯ ⎯ ⎯
connector plug
communication (110Ω)
(including 1)
For modules with a width of 41mm
(AJ65VBTCU -8 , AJ65VBTCU -32 ,
Connector Type A6PLT-J65V1 ⎯ ⎯ ⎯
AJ65VBTCU-68 )
Metal Installation
10 M4 8 SWPW attached hole section screws
Fitting
(set of 5) For modules with a width of 60mm
A6PLT-J65V2 ⎯ (AJ65VBTCU -16 ) ⎯ ⎯
10 M4 8 SWPW attached hole section screws
1 Mitsubishi's A6CON-P , A6CAP- 1 includes 20 plugs.
2 Mitsubishi's A6CON- 5P includes 10 plugs.
3 Mitsubishi's A6CON- J5P includes 5 plugs.
4 Confirm the outer sheath diameter of the applicable cable and select the connector.

1 - 29 1 - 29
1 OVERVIEW
MELSEC-A

Mitsubishi
Applicable module
model name
Input : AJ65SBTB1-8D
A6CVR-8 Output : AJ65SBTB1-8T AJ65SBTB1-8TE AJ65SBTB1-8T1
Repeater : AJ65SBT-RPT
Input : AJ65SBTB1-16D AJ65SBTB1-16D1 AJ65SBTC1-32D AJ65SBTC1-32D1
AJ65SBTC4-16D AJ65SBTC4-16DN AJ65SBTC4-16DE AJ65SBTB3-8D
AJ65SBTB2-8A AJ65SBTB2N-8A
Output : AJ65SBTB1-16T AJ65SBTC1-32T AJ65SBTB1-16T1 AJ65SBTB2-8T
AJ65SBTB1-16TE AJ65SBTB2-8R AJ65SBTB2-8S AJ65SBTB2N-8R
A6CVR-16
AJ65SBTB2N-8S AJ65SBTB2-8T1
Combined : AJ65SBTC1-32DT AJ65SBTC1-32DT1 AJ65SBTC4-16DT AJ65SBTB1-6DT
Protect cover
AJ65SBTB1-16DT1 AJ65SBTB1-16DT2 AJ65SBTB32-8DT AJ65SBTC1-32DT2
for compact
AJ65SBTC1-32DT3 AJ65SBTC4-16DT2 AJ65SBTB1-16DT3 AJ65SBTB32-8DT2
remote I/O
Optical Repeater : AJ65SBT-RPS AJ65SBT-RPG
module
Input : AJ65SBTB1-32D AJ65SBTB1-32D1 AJ65SBTB2-16A AJ65SBTB2N-16A
(including 10)
AJ65SBTB3-16D
Output : AJ65SBTB1-32T AJ65SBTB1-32T1 AJ65SBTB2-16T AJ65SBTB2-16R
A6CVR-32
AJ65SBTB2-16S AJ65SBTB2N-16R AJ65SBTB2N-16S AJ65SBTB2-16T1
Combined : AJ65SBTB1-32DT AJ65SBTB1-32DT1 AJ65SBTB1-32DT2 AJ65SBTB32-16DT
AJ65SBTB1-32DT3 AJ65SBTB32-16DT2
Input : AJ65VBTCE3-8D
A6CVR-VCE8
Output : AJ65VBTCE2-8T
Input : AJ65VBTCE3-16D AJ65VBTCE3-16DE
A6CVR-VCE16 Output : AJ65VBTCE2-16T AJ65VBTCE3-16TE
Combined : AJ65VBTCE32-16DT AJ65VBTCE3-16DTE
Input : AJ65DBTB1-32D
DIN adapter A6DIN1C Output : AJ65DBTB1-32T1 AJ65DBTB1-32R
Combined : AJ65DBTB1-32DT1 AJ65DBTB1-32DR
Common Input : AJ65DBTB1-32D
Terminal A2CCOM-TB Output : AJ65DBTB1-32T1 AJ65DBTB1-32R
Block Combined : AJ65DBTB1-32DT1 AJ65DBTB1-32DR

1 - 30 1 - 30
1 OVERVIEW
MELSEC-A

1.6 Recommended Connection Device List

1.6.1 Recommended connection devices for low profile waterproof remote I/O module

The following shows communication devices needed for use of the low profile
waterproof type remote I/O module (AJ65FBTA -16 ).

(1) Communications Module Waterproof Plug (Male / Female) 4-pin

/ 5-pin can be used.
(a) For LINK In Side (Female)
Model Name Maker Specifications Connection Cable Diameter
ELKA 4012 PG9 HIRSCHMANN M12-4-pin Female Straight Type φ6.0 to 8.0mm
ELKA 5012 PG9 HIRSCHMANN M12-5-pin Female Straight Type φ6.0 to 8.0mm
CM02A-8DP5S(03) DDK Ltd. M12-4-pin Female Straight Type φ7.2 to 7.9mm
ELWIKA 4012 PG9 HIRSCHMANN M12-4-pin Female Right-angle Type φ6.0 to 8.0mm
ELWIKA 5012 PG9 HIRSCHMANN M12-5-pin Female Right-angle Type φ6.0 to 8.0mm
(b) For LINK OUT Side (Male)
Model Name Maker Specifications Connection Cable Diameter
ELST 4012 PG9 HIRSCHMANN M12-4-pin Male Straight Type φ6.0 to 8.0mm
ELST 5012 PG9 HIRSCHMANN M12-5-pin Male Straight Type φ6.0 to 8.0mm
CM02A-8DJ5P(03) DDK Ltd. M12-4-pin Female Straight Type φ7.2 to 7.9mm
ELWIST 4012 PG9 HIRSCHMANN M12-4-pin Male Right-angle Type φ6.0 to 8.0mm
ELWIST 5012 PG9 HIRSCHMANN M12-5-pin Male Right-angle Type φ6.0 to 8.0mm

(2) Power Supply Module - Waterproof Plug (Female) 5-pin only can
be used.
Model Name Maker Specifications Connection Cable Diameter
ELKA 5012 PG7 φ4.0 to 6.0mm
HIRSCHMANN M12-5-pin Female Straight Type
ELKA 5012 PG9 φ6.0 to 8.0mm
ELWIKA 5012 PG7 φ4.0 to 6.0mm
HIRSCHMANN M12-5-pin Female Right-angle Type
ELWIKA 5012 PG9 φ6.0 to 8.0mm

(3) I/O connector waterproof plug (male) 4-pin/5-pin can be used.

The plug for LINK OUT side (male) mentioned in Section (1) (b)
can be used.

(4) I/O Connector Y Branch Connector

Model Name Maker Remarks
SAC-3P-M12Y
PHOENIX CONTACT ⎯
SAC-5P-M12Y
XS2R series OMRON Corporation ⎯
VA-4YG-2 CORRENS Corporation ⎯

(5) CC-Link Cable

Model Name Maker Remarks
MITSUBISHI ELECTRIC ENGINEERING Co.,Ltd CC-Link dedicated cable with waterproof
FA-CBL series
connector
Cable with M12 Connector Shinwa Co.,Ltd The CA series cannot be used.

1 - 31 1 - 31
1 OVERVIEW
MELSEC-A

1.6.2 Recommended connection devices for low profile sensor connector (e-CON) remote
I/O module

The following shows communication devices needed for use of the sensor connector
(e-CON) remote I/O module (AJ65VBTCE - ).
For how to wire the sensor connector (e-CON), refer to the catalog of the
corresponding maker.

(1) I/O sensor connector (e-CON) plug 1

Specifications
Cover
Model Name Maker Applicable cable Maximum rated
Applicable cable core size Color
outer diameter current
2
0.08 to 0.20mm
ECN-A014R φ0.9 to 1.0mm Red
(AWG28 to 24)
2
0.20 to 0.30mm
ECN-A004Y φ1.0 to 1.15mm Yellow
(AWG24 to 22)
2
0.30 to 0.50mm
ECN-A024BL (Mitsubishi φ1.15 to 1.3mm Blue
(AWG22 to 20)
Electric System 2A
ECN-M014R 2 φ0.8 to 1.0mm Red
Service Co., Ltd.) 0.14 to 0.30mm
ECN-M024Y φ1.0 to 1.2mm Yellow
(AWG26 to 24)
ECN-M034OR φ1.2 to 1.6mm Orange
ECN-M044GN 2 φ1.0 to 1.2mm Green
0.30 to 0.50mm
ECN-M054BL φ1.2 to 1.6mm Blue
(AWG22 to 20)
ECN-M064GY φ1.6 to 2.0mm Gray
1 The ECN- includes 20 plugs.

1 - 32 1 - 32
1 OVERVIEW
MELSEC-A

1.7 About the Generic, Abbreviated and Technical Terms Used in This Manual

The abbreviated and technical terms used in this manual are listed below:
Generic/abbreviated/
Description
technical term
Generic term for the AJ61BT11, A1SJ61BT11, AJ61QBT11, A1SJ61QBT11, QJ61BT11 and
Master/local module
LJ61BT11 CC-Link system master/local modules
Compact remote I/O module Generic term for the AJ65SBT - CC-Link system compact remote I/O modules
Conventional remote I/O
Generic term for the AJ65BT - CC-Link system remote I/O modules
module
Generic term for the AJ65BT - /AJ65SBT - /AJ65V - /AJ65F - CC-Link
Remote I/O module
system remote I/O modules
Input module Generic term for the AJ65SBT - A/D(1) remote I/O modules
Output module Generic term for the AJ65SBT - R/T /T1/TE remote I/O modules
Combined module Generic term for the AJ65SBT - DT(1) remote I/O modules
Waterproof type remote I/O
Generic term for the AJ65SBTW4-16 remote I/O modules
module
Low profile waterproof type
Generic term for the AJ65FBTA -16 remote I/O modules
remote I/O module
Spring clamp terminal block
Generic term for the AJ65VBTS - remote I/O modules
type remote I/O module
Sensor connector (e-CON)
Generic term for the AJ65VBTCE - remote I/O modules
type remote I/O module

1 - 33 1 - 33
1 OVERVIEW
MELSEC-A

MEMO

1 - 34 1 - 34
 2 NAMES AND SETTINGS FOR EACH PART
MELSEC-A

2 NAMES AND SETTINGS FOR EACH PART

The names and settings for the components of the compact remote I/O module are
shown below:
AJ65SBTB1-8 (Terminal-block 8 point module, 1-wire)

2 1) 4) 2)

STATION NO. B RATE

X0 1 2 3 4 5 6 7 40 20 10 8 4 2 1 4 2 1

ON

A J65SBTB1-8D
DA DG +24V 24G X0 X2 X4 X6 COM
DB SLD (FG) X1 X3 X5 X7 COM

9) 11)

AJ65SBTB1-16 (Terminal-block 16 point module, 1-wire)

1) 4) 2)

X0 1 2 3 4 5 6 7 X8 9 A B C D E F STATION NO. B RATE

40 20 10 8 4 2 1 4 2 1

ON

AJ65SBTB1-16D
DA DG +24V 24G X0 X2 X4 X6 X8 XA XC XE COM
DB SLD (FG) X1 X3 X5 X7 X9 XB XD XF COM

11)
9)

AJ65SBTB1B-16 (Module with 1-wire terminal block, 2-common type, and 16 points)
1) 4) 2)

PW L RUN L ERR. Y0 1 2 3 4 5 6 7 Y8 9 A B C D E F STATION NO. B RATE

40 20 10 8 4 2 1 4 2 1

ON

AJ65SBTB1B-16TE1
DA DG +24V 24G Y0 Y1 Y2 Y3 Y4 Y5 Y6 Y7 Y8 Y9 YA YB YC YD YE YF NC
DB SLD (FG) COM1- COM1- COM1- COM1- COM1- COM1- CTL1- COM1+ COM2- COM2- COM2- COM2- COM2- COM2- CTL2- COM2+ NC

11) 9) 11)

2-1 2-1
2 NAMES AND SETTINGS FOR EACH PART
MELSEC-A

AJ65SBTB1-32 (Terminal-block 32 point module, 1-wire)

1) 4) 2)

PW L RUN L ERR. X0 1 2 3 4 5 6 7 X8 9 A B C D E F X10 11 12 13 14 15 16 17 X18 19 1A1B 1C1D1E 1F STATION NO. B RATE

40 20 10 8 4 2 1 4 2 1

ON

AJ65SBTB1-32D
DA DG +24V 24G X0 X2 X4 X6 X8 XA XC XE X10 X12 X14 X16 X18 X1A X1C X1E COM
DB SLD (FG) X1 X3 X5 X7 X9 XB XD XF X11 X13 X15 X17 X19 X1B X1D X1F COM
2

9)
11) 11)

AJ65SBTB1-32K (Terminal-block 32 point module, 1-wire)

1) 8) 4) 2)

11) 9) 11)

AJ65SBTC1-32 (One-touch connector 32 point module, 1-wire)

1) 6) 4) 2)

STATION NO. B RATE

X0 1 2 3 4 5 6 7 X8 9 A B C D E F
X0-XF 40 20 10 8 4 2 1 4 2 1 ON

X1011121314 1516 17 X1819 1A1B1C1D1E1F

A J65SBTC1-32D1 X10-X1F

DA DG +24V 24G COM

X0 X4 X8 XC X10 X14 X18 X1C
DB SLD (FG) X1 X5 X9 XD X11 X15 X19 X1D COM
X2 X6 XA XE X12 X16 X1A X1E
X3 X7 XB XF X13 X17 X1B X1F

9) 11) 10) 9)

2-2 2-2
2 NAMES AND SETTINGS FOR EACH PART
MELSEC-A

AJ65SBTC4-16 (One-touch connector 16 point module, 4-wire)

1) 4) 2)

STATION NO. B RATE

X0 1 2 3 4 5 6 7 X8 9 A B C D E F
40 20 10 8 4 2 1 4 2 1 ON

A J65SBTC4-16DN
DA DG +24V 24G
X0 X1 X2 X3 X4 X5 X6 X7 COM+
DB SLD (FG) Y8 Y9 YA YB YC YD YE YF COM-
+24V +24V +24V +24V +24V +24V +24V +24V
24G 24G 24G 24G 24G 24G 24G 24G

9) 11) 10) 9)

(AJ65SBTC4-16D only)

AJ65SBTCF1-32 (Terminal block 32 point module, 1-wire FCN 40-pin connector)

1) 6) 4) 2)

STATION NO. B RATE

X0 1 2 3 4 5 6 7 X8 9 A B C D E F
X0-XF 40 20 10 8 4 2 1 4 2 1
ON

X10 111213 1415 1617 X18191A1B1C1D1E1F

A J65SBTCF1-32D X10-X1F

DA DG +24V 24G X10 X11 X12 X13 X14 X15 X16 X17 X18 X19 X1A X1B X1C X1D X1E X1F NC NC NC NC

DB SLD (FG) X0 X1 X2 X3 X4 X5 X6 X7 X8 X9 XA XB XC XD XE XF NC NC COM COM

9) 11) 10)

2-3 2-3
2 NAMES AND SETTINGS FOR EACH PART
MELSEC-A

AJ65SBTB2N-8 (Terminal block 8 point module, 2-wire)

4) 2) 1)

STATION NO. B RATE X0 1 2 3 4 5 6 7

40 20 10 8 4 2 1 4 2 1
A J65SBTB2N-8A
ON

DA DG +24V 24G X0 X1 X2 X3 X4 X5 X6 X7 COMA

DB SLD (FG) COMB COMB COMB COMB COMB COMB COMB COMB COMB

9) 11)

AJ65SBTB2N-16 (Terminal block 16 point module, 2-wire)

4) 2) 1)

STATION NO. B RATE PW L RUN L ERR. X0 1 2 3 4 5 6 7 X8 9 A B C D E F

40 20 10 8 4 2 1 4 2 1
AJ65SBTB2N-16A
ON

DA DG +24V 24G X0 X1 X2 X3 X4 X5 X6 X7 X8 X9 XA XB XC XD XE XF COMA

DB SLD (FG) COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB

11) 9) 11)

AJ65SBTB2-8 (Terminal block 8 point module, 2-wire)

1) 4) 2)

STATION NO. B RATE

Y0 1 2 3 4 5 6 7 40 20 10 8 4 2 1 4 2 1

ON

AJ65SBTB2-8T
DA DG +24V 24G Y0 Y1 Y2 Y3 Y4 Y5 Y6 Y7 DC24V

DB SLD (FG) COM COM COM COM COM COM COM COM DC24G

9) 11)

2-4 2-4
2 NAMES AND SETTINGS FOR EACH PART
MELSEC-A

AJ65SBTB2-16 (Terminal block 16 point module, 2-wire)

1) 4) 2)

PW L RUN L ERR. Y0 1 2 3 4 5 6 7 Y8 9 A B C D E F STATION NO. B RATE

40 20 10 8 4 2 1 4 2 1

ON

AJ65SBTB2-16T
DA DG +24V 24G Y0 Y1 Y2 Y3 Y4 Y5 Y6 Y7 Y8 Y9 YA YB YC YD YE YF DC24V

DB SLD (FG) COM COM COM COM COM COM COM COM COM COM COM COM COM COM COM COM DC24G

11) 9) 11)

AJ65SBTB3-8 (Terminal block 8 point module, 3-wire)

1) 4) 2)

STATION NO. B RATE

X0 1 2 3 4 5 6 7
40 20 10 8 4 2 1 4 2 1

ON

AJ65SBTB3-8D
DA DG +24V 24G X0 X1 X2 X3 X4 X5 X6 X7 DC24A

DB SLD (FG) COMA COMB COMA COMB COMA COMB COMA COMB DC24B

9) 11)

AJ65SBTB3-16 (Terminal block 16 point module, 3-wire)

1) 4) 2)

PW L RUN L ERR. X0 1 2 3 4 5 6 7 X8 9 A B C D E F STATION NO. B RATE

40 20 10 8 4 2 1 4 2 1

ON

AJ65SBTB3-16D
DA DG +24V 24G X0 X1 X2 X3 X4 X5 X6 X7 X8 X9 XA XB XC XD XE XF DC24A

DB SLD (FG) COMA COMB COMA COMB COMA COMB COMA COMB COMA COMB COMA COMB COMA COMB COMA COMB DC24B

11) 9) 11)

2-5 2-5
2 NAMES AND SETTINGS FOR EACH PART
MELSEC-A

AJ65SBTB3-16K (Terminal block 16 point module, 3-wire)

1) 8) 4) 2)

11) 9) 11)

AJ65SBTB32-8 (Terminal block 8 point module, 3-wire input, 2-wire output)

1) 4) 2)

STATION NO. B RATE

X0 1 2 3 Y8 9 A B 40 20 10 8 4 2 1 4 2 1

ON

AJ65SBTB32-8DT
DA DG +24V 24G X0 X1 X2 X3 Y8 Y9 YA YB DC24V

DB SLD (FG) COM+ COM- COM+ COM- COM+ COM+ COM+ COM+ DC24G

9) 11)

AJ65SBTB32-16 (Terminal block 16 point module, 3-wire input, 2-wire output)

4) 2)
1)
PW L RUN L ERR. X0 1 2 3 4 5 6 7 Y8 9 A B C D E F STATION NO. B RATE
40 20 10 8 4 2 1 4 2 1

ON

AJ65SBTB32-16DT
DA DG +24V 24G X0 X1 X2 X3 X4 X5 X6 X7 Y8 Y9 YA YB YC YD YE YF DC24A

DB SLD (FG) COM+ COM- COM+ COM- COM+ COM- COM+ COM- COM+ COM+ COM+ COM+ COM+ COM+ COM+ COM+ DC24B

9)
11) 11)

2-6 2-6
2 NAMES AND SETTINGS FOR EACH PART
MELSEC-A

AJ65SBTB32-16K (Terminal block 16 point module, 3-wire input, 2-wire output)

1) 8) 4) 2)

9)
11) 11)

AJ65SBTB32-16DR (Terminal block 16 point module, 3-wire input, 2-wire output)

4) 2) 1)

YD

11) 9) 11)

AJ65SBTB32-16KDR (Terminal block 16 point module, 3-wire input, 2-wire output)

8) 4) 2) 1)

11) 9) 11)

2-7 2-7
2 NAMES AND SETTINGS FOR EACH PART
MELSEC-A

AJ65DBTB1-32 (Terminal block 32 point module, 1-wire)

AJ65DBTB1-32D
6 PW L RUN L ERR.
5 0 ~0
1
5) 4 1 0 8 10 18
3 2
STATI ON NO. 1 9 11 19
7 8 2 A 12 1A
5
6

4
3 2
9

1
0 ~
1 3
4
B
C
13
14
1B
1C
1)
5 D 15 1D

3) B RATE
4
3 2
1
0
6
7
E
F
16
17
1E
1F

DA NC
DG NC
DB +24V
NC NC
SLD
( FG)
NC NC
24G 24G

X0 X10
X1 X11
X2 X12
X3 X13
9) X4 X14 9)
X5 X15
X6 X16
X7 X17
COM1 COM3
X8 X18
X9 X19
XA X1A
XB X1B
XC X1C
XD X1D
XE X1E
XF X1F
COM4
COM2

AJ65DBTB1
- 32D

2-8 2-8
2 NAMES AND SETTINGS FOR EACH PART
MELSEC-A

No. Item Description

1) Operation status indicator LED LED name Details
On: Power being supplied
PW
Off: No power supplied
On: Normal communication
L RUN
Off: No communication (timeout error)
On: Communication error
Flashing regularly:
The station number or transmission speed switch setting
is changed while power is on.
L ERR. Flashing irregularly:
The terminating resistor setting is incorrect.
The module or CC-Link dedicated cable is affected by
noise.
Off: Normal communication
X0 to 1F On: Input/output ON
Y0 to 1F Off: Input/output OFF
2) Transmission speed setting
Switch status Transmission
switch Setting
4 2 1 speed
0 OFF OFF OFF 156kbps
1 OFF OFF ON 625kbps
2 OFF ON OFF 2.5 Mbps
3 OFF ON ON 5.0 Mbps
4 ON OFF OFF 10 Mbps

Set the transmission speed within the above range.

3) Transmission speed setting
switch Setting Transmission speed
0 156kbps
1 625kbps
2 2.5 Mbps
3 5.0 Mbps
4 10 Mbps

Set the transmission speed within the above range.

2-9 2-9
2 NAMES AND SETTINGS FOR EACH PART
MELSEC-A

No. Item Description

4) Station number setting switch Select "10", "20", or "40" for the tens place.
Select "1", "2", "4", or "8" for the ones place.
*1
Set the station number within the range of 1 to 64.
Station Tens place Ones place
number 40 20 10 8 4 2 1
1 OFF OFF OFF OFF OFF OFF ON
2 OFF OFF OFF OFF OFF ON OFF
3 OFF OFF OFF OFF OFF ON
4 OFF OFF OFF OFF OFF OFF OFF
: : : : : : : :
10 OFF OFF ON OFF OFF OFF OFF
11 OFF OFF ON OFF OFF OFF ON
: : : : : : : :
64 ON ON OFF OFF ON OFF OFF

(Example) Setting the station number to 32:

Station Tens place Ones place
number 40 20 10 8 4 2 1
32 OFF ON ON OFF OFF ON OFF

*1
5) Station number setting switch Set the station number within the range of 1 to 64.
• Use "×10" for the tens place.
• Use "×1" for the ones place.
*2
6) Indication selector switch When the switch is set to "X0-XF", LEDs indicate the ON/OFF status of X0 to
XF.
When the switch is set to "X10-X1F", LEDs indicate the ON/OFF status of X10
to X1F.
7) Sink/source switch Switches the input type (sink or source).
(For AJ65SBTC1-16D only) Open the module top cover to set the switch.
<When setting for sink type> <When setting for source type>
SOURCE SOURCE

Switch

SINK SINK

8) Input response speed switch

Switch status
Setting Input response speed
2 1
0 OFF OFF 10ms
1 OFF ON 5ms
2 ON OFF 1.5ms
3 ON ON 0.2ms
*2
Default: 2 (1.5ms)
9) Terminal block Terminal block for module power supply, transmission, and I/O signals.
10) Connector Connector for I/O signals.
11) DIN rail hook When mounting the module to a DIN rail, push in the DIN rail hook until it clicks.
1 A unique station number should be set.
2 The switch setting is reflected/held at power-on.
When it is changed while power is on, turn off the power and then on again.

2 - 10 2 - 10
2 NAMES AND SETTINGS FOR EACH PART
MELSEC-A

AJ65SBTW4-16 (waterproof connector 16 point module, 1-wire)

4) 7)

2)

3)

9) SINK SOURCE

6) 1)

10) LINK CABL IN POWER CABL PW L RUN

L ERR.
X0 Y8
X1 Y9
X2 YA
X3 YB
CON1 CON3 CON5 CON7 X4 YC
8) LINK CABL OUT POWER CABL CON2 CON4 CON6 CON8
X5 YD
X6 YE
X7 YF

STATION NO.

MITSUBISHI AJ65SBTW4-16DT

5)

No. Item Description

1) Operating status indicator LED LED name Details
On: Power being supplied
PW
Off: No power supplied
On: Normal communication
L RUN
Off: No communication (timeout error)
On: Communication error
Flashing regularly:
The station number or transmission speed switch setting
is changed while power is on.
L ERR. Flashing irregularly:
The terminating resistor setting is incorrect.
The module or CC-Link dedicated cable is affected by
noise.
Off: Normal communication
X0 to 7 On: Input/output ON
Y8 to F Off: Input/output OFF

2 - 11 2 - 11
2 NAMES AND SETTINGS FOR EACH PART
MELSEC-A

No. Item Description

2) Transmission speed setting switch
Switch status Transmission
Setting
4 2 1 speed
0 OFF OFF OFF 156kbps
1 OFF OFF ON 625kbps
2 OFF ON OFF 2.5 Mbps
3 OFF ON ON 5.0 Mbps
4 ON OFF OFF 10 Mbps

Set the transmission speed within the above range.

Open the module top cover to set the transmission speed.
3) Station number setting switch Select "10", "20", or "40" for the tens place.
Select "1", "2", "4", or "8" for the ones place.
*1
Set the station number within the range of 1 to 64.
Station Tens place Ones place
number 40 20 10 8 4 2 1
1 OFF OFF OFF OFF OFF OFF ON
2 OFF OFF OFF OFF OFF ON OFF
3 OFF OFF OFF OFF OFF ON
4 OFF OFF OFF OFF OFF OFF OFF
: : : : : : : :
10 OFF OFF ON OFF OFF OFF OFF
11 OFF OFF ON OFF OFF OFF ON
: : : : : : : :
64 ON ON OFF OFF ON OFF OFF

(Example) Setting the station number to 32:

Station Tens place Ones place
number 40 20 10 8 4 2 1
32 OFF ON ON OFF OFF ON OFF

Open the module top cover to set the station number.

4) Terminal block Terminal block for module power supply and transmission circuit.
5) Pipe for transmission or power Pipe for connecting a transmission cable or a power supply cable to the
supply line terminal block.
Open the module top cover to connect a transmission cable or a power supply
cable to the terminal block.
Attach a waterproof plug provided with the product to the unused pipe.
6) Waterproof connector for I/O Waterproof connectors for I/O signals.
Attach an optional dustproof cap (A6CAP-DC1) to the unused
waterproof connector.
7) Sink/source switch Switches the input type (sink or source).
(For AJ65SBTW4-16D only) Open the module top cover to set the switch.
< When setting for sink type > < When setting for source type >
SOURCE SOURCE

Switch

SINK SINK

8) Metal fitting FG terminal for module.

9) Module top-cover installation
screw (M3)
Refer to Section 7.1 for tightening torque value for installation screws.
10) Module front-cover installation
screw (M3)
1 A unique station number should be set.

2 - 12 2 - 12
2 NAMES AND SETTINGS FOR EACH PART
MELSEC-A

AJ65VBTCU -8 (One-touch connector 8 points module)

40
20
10
8 3)
4
2
1
4
2 2)
1

AJ65VBTCU3-8D1
CON
A
5)
CON
B

X0 PW

L RUN
X1
L ERR

X2 1)
0
1
2
X3
3
7) 4
5
8)
X4 6
7

X5

X6

X7

CON
C
6)

CON
D

2 - 13 2 - 13
2 NAMES AND SETTINGS FOR EACH PART
MELSEC-A

AJ65VBTCU -16 (One-touch connector 16 points module)

40
20
10
8 3)
4
2
1
4
2 2)
1

AJ65VBTCU3-16D1
CON
A
5)
CON
B

PW

L RUN

L ERR

0
1
2
3
7) 4 1) 8)
5
6
7

8
9
A
B
C
D
E
X0 to X7 X8 to XF F

CON
C
6)
CON
D

2 - 14 2 - 14
2 NAMES AND SETTINGS FOR EACH PART
MELSEC-A

AJ65VBTCF1-32DT1 (1-wire FCN connector 32 points module)

40
20
10
8 3)
4
2
1
4
2 2)
1

AJ65VBTCF1-32DT1

LINK X0 Y10
to to 4)
CON.A CON.B XF Y1F

PW

L RUN
5) L ERR

0
1
2
3
4
5 8)
6
7 1)

8
9
A
B
PW/AUX.
C
CON.C CON.D D
E
F

6)
7)

2 - 15 2 - 15
2 NAMES AND SETTINGS FOR EACH PART
MELSEC-A

No. Item Description

1) Operating status indicator LED LED name Details
On: Power being supplied
PW
Off: No power supplied
On: Normal communication
L RUN
Off: No communication (timeout error)
On: Communication error
Flashing regularly:
The station number or transmission speed switch setting
is changed while power is on.
L ERR. Flashing irregularly:
The terminating resistor setting is incorrect.
The module or CC-Link dedicated cable is affected by
noise.
Off: Normal communication
On: Input/output ON
0 to F
Off: Input/output OFF
2) Transmission speed setting switch
Switch status Transmission
Setting
4 2 1 speed
0 OFF OFF OFF 156kbps
1 OFF OFF ON 625kbps
2 OFF ON OFF 2.5 Mbps
3 OFF ON ON 5.0 Mbps
4 ON OFF OFF 10 Mbps

Set the transmission speed within the above range.

3) Station number setting switch Select "10", "20", or "40" for the tens place.
Select "1", "2", "4", or "8" for the ones place.
*1
Set the station number within the range of 1 to 64.
Station Tens place Ones place
number 40 20 10 8 4 2 1
1 OFF OFF OFF OFF OFF OFF ON
2 OFF OFF OFF OFF OFF ON OFF
3 OFF OFF OFF OFF OFF ON
4 OFF OFF OFF OFF OFF OFF OFF
: : : : : : : :
10 OFF OFF ON OFF OFF OFF OFF
11 OFF OFF ON OFF OFF OFF ON
: : : : : : : :
64 ON ON OFF OFF ON OFF OFF

(Example) Setting the station number to 32:

Station Tens place Ones place
number 40 20 10 8 4 2 1
32 OFF ON ON OFF OFF ON OFF

1 A unique station number should be set.

2 - 16 2 - 16
2 NAMES AND SETTINGS FOR EACH PART
MELSEC-A

No. Item Description

*2
4) Indication selector switch When the switch is set to "X0-XF", LEDs indicate the ON/OFF status of X0 to
XF.
When the switch is set to "Y10-Y1F", LEDs indicate the ON/OFF status of Y10
to Y1F.
5) Connector for communication One-touch connector for communication line.
When carrying out wiring, connect two optional one-touch connector plugs for
communication (A6CON-L5P) at top and bottom.
When changing the module online, connect the optional online connectors
(A6CON-LJ5P) between the connector and plugs.
When using the module at either end of the CC-Link system, fit the optional
one-touch connector plug with termination resistor (110Ω) (A6CON-TR11).
6) Connector for power supply and One-touch connector for module power supply line, I/O power supply line, and
FG FG.
When carrying out jumper wiring, connect two optional one-touch connector
plugs for power supply/FG at top and bottom. Two different types (A6CON-
PW5P, A6CON-PW5P-SOD) are available as the one-touch connector plugs
for power supply and FG.
When not carrying out jumper wiring, also connect the plugs (for safety and
dust prevention).
When changing the module online, connect the optional online connectors
(A6CON-PWJ5P) between the connector and plugs.
7) Connector Connector for I/O signals.
8) DIN rail hook Hook to install the module to the DIN rail or connector type Metal installation
fitting (option).
When mounting the module to a DIN rail, push in the DIN rail hook until it
clicks.
2 To operate the indication selector switch, do not use a tool such as a screwdriver. Doing so may damage the switch.

2 - 17 2 - 17
2 NAMES AND SETTINGS FOR EACH PART
MELSEC-A

AJ65FBTA -16 (Low profile waterproof connector 16 points module)

Connector for module
4)

TERMINATION
110 130
ON 5) 5)
1 2 a b

9)

Communication adapter (back) Communication adapter (front)

Connector for
communication adapter 10)
3)
8)
2)

ON

40 20 10 8 4 2 1 4 2 1
STATION NO B RATE

Communication
adapter AJ65FBTA42-16DTE

PROTECT
Y8
Y9
YA
YB 1)
YC
YD
YE
YF

6) 6)
c d

Y
Y

Y
Y

7) 7)

Y
Y

Y
Y

Terminal number sheet

2 - 18 2 - 18
2 NAMES AND SETTINGS FOR EACH PART
MELSEC-A

No. Item Description

1) Operating status indicator LED name Details
LED On: Power being supplied
POWER
Off: No power supplied
On: Any protection of the output part was activated.
PROTECT (The blown fuse was detected in the master module.)
Off: Normal operation
On: Normal communication
L RUN
Off: No communication (timeout error)
On: Communication error
Flashing regularly:
The station number or transmission speed switch setting is changed
while power is on.
L ERR. Flashing irregularly:
The terminating resistor setting is incorrect.
The module or CC-Link dedicated cable is affected by noise.
Off: Normal communication
X0 to X7/
Y0 to YF/ On: Input/output ON
X0 to X7, Off: Input/output OFF
Y8 to YF
2) Transmission speed setting
Switch status
switch Setting Transmission speed
4 2 1
0 OFF OFF OFF 156kbps
1 OFF OFF ON 625kbps
2 OFF ON OFF 2.5 Mbps
3 OFF ON ON 5.0 Mbps
4 ON OFF OFF 10 Mbps
Set the transmission speed within the above range.
Remove the communication adapter to set the transmission speed. (Default: all OFF)
3) Station number setting Select "10", "20", or "40" for the tens place.
switch Select "1", "2", "4", or "8" for the ones place.
*1
Set the station number within the range of 1 to 64.
(Example) Setting the station number to 32:
Tens place Ones place
Station number
40 20 10 8 4 2 1
10 ON OFF ON OFF OFF OFF OFF
Remove the communication adapter to set the station number. (Default: all OFF)
4) Terminal resistor setting Used to set the terminating resistor.
switch DIP switch
Contents
1 2
OFF OFF No terminating resistor
ON OFF 110Ω terminating resistor
OFF ON 130Ω terminating resistor
ON ON Setting prohibited
(Default: all OFF)
1 A unique station number should be set.

2 - 19 2 - 19
2 NAMES AND SETTINGS FOR EACH PART
MELSEC-A

No. Item Description

5) Waterproof connector for
*2
transmission line Printing Description
Connector (male, 4 pins) for the IN-side (master
a LINK IN
station side) transmission line
Connector (female, 5 pins) for the OUT-side
transmission line.
b LINK OUT Attach a waterproof cap (accessory) to the unused
connector.
(Tightening torque range:0.29 to 0.34N•m)

6) Waterproof connector for

*2
power line Printing Description
Connector (male, 5 pins) for supplying power to the
c UNIT POWER
module
Connector (male, 5 pins) for supplying
d AUX.
power to loads

7) Waterproof connector for Waterproof connectors for I/O signals.

*2
I/O Attach an optional waterproof cap (A6CAP-WP2) to the unused waterproof connector.
(Tightening torque range: 0.29 to 0.34N•m)
8) FG terminal FG terminal for module
9) Communication adapter Used to mount or remove a communication adapter while the module is online.
mounting screw (Tightening torque range: 0.42 to 0.58N•m)
10) Module mounting hole Screw holes for mounting the module (2-4.5 × 6, M4 screw)
(Tightening torque range: 0.78 to 1.18N•m)
2 Waterproof connector (compliant with IEC 60947-5-2, M12)

2 - 20 2 - 20
2 NAMES AND SETTINGS FOR EACH PART
MELSEC-A

AJ65VBTS -16 (Spring clamp terminal block type 16 points module)

1) 7) 10)
ON
PW L RUN L ERR.

B RATE STATION NO.

1 2 4 1 2 4 8 1020 40
AJ65VBTS3-16D
3) 0 1 2 3 4 5 6 7

8 9 A B C D E F
2) NC X0 X1 X2 X3 X4 X5 X6 X7 X8 X9 XA XB XC XD XE XF

COM+ COM+
9)
COM- COM-

CON A B C D

9) 10) 5) 6) 8)

AJ65VBTS -32 (Spring clamp terminal block type 32 points module)

7) 9)
1) 4)
ON
PW L RUNL ERR.
B RATESTATION NO.
1 2 4 1 2 4 8102040

3)
AJ65VBTS3-32D
0 1 2 3 4 5 6 7

2)
8 9 A B CD E F
NC X0 X1 X2 X3 X4 X5 X6 X7 X8 X9 XA XB XC XD XE XF NC X10 X11 X12 X13 X14 X15 X16 X17 X18 X19 X1A X1B X1C X1D X1E X1F

COM1+ COM1+ COM2+ COM2+

COM1- COM1- COM2- COM2-

CON A B C D

9) 5) 6) 8) 8)

2 - 21 2 - 21
2 NAMES AND SETTINGS FOR EACH PART
MELSEC-A

No. Item Description

1) Operating status indicator LED LED name Details
On: Power being supplied
PW
Off: No power supplied
On: Normal communication
L RUN
Off: No communication (timeout error)
On: Communication error
Flashing regularly:
The station number or transmission speed switch setting
is changed while power is on.
L ERR. Flashing irregularly:
The terminating resistor setting is incorrect.
The module or CC-Link dedicated cable is affected by
noise.
Off: Normal communication
On: Input/output ON
0 to F
Off: Input/output OFF
2) Transmission speed setting switch
Switch status Transmission
Setting
4 2 1 speed
0 OFF OFF OFF 156kbps
1 OFF OFF ON 625kbps
2 OFF ON OFF 2.5 Mbps
3 OFF ON ON 5.0 Mbps
4 ON OFF OFF 10 Mbps

Set the transmission speed within the above range.

3) Station number setting switch Select "10", "20", or "40" for the tens place.
Select "1", "2", "4", or "8" for the ones place.
*1
Set the station number within the range of 1 to 64.
Station Tens place Ones place
number 40 20 10 8 4 2 1
1 OFF OFF OFF OFF OFF OFF ON
2 OFF OFF OFF OFF OFF ON OFF
3 OFF OFF OFF OFF OFF ON
4 OFF OFF OFF OFF OFF OFF OFF
: : : : : : : :
10 OFF OFF ON OFF OFF OFF OFF
11 OFF OFF ON OFF OFF OFF ON
: : : : : : : :
64 ON ON OFF OFF ON OFF OFF

(Example) Setting the station number to 32:

Station Tens place Ones place
number 40 20 10 8 4 2 1
32 OFF ON ON OFF OFF ON OFF

1 A unique station number should be set.

2 - 22 2 - 22
2 NAMES AND SETTINGS FOR EACH PART
MELSEC-A

No. Item Description

*2
4) Indication selector switch When the switch is set to "F", LEDs indicate the ON/OFF status of the first 16
points.
When the switch is set to "L", LEDs indicate the ON/OFF status of the latter 16
points.
5) Connector for communication One-touch connector for communication line.
When carrying out wiring, connect two optional one-touch connector plugs for
communication (A6CON-L5P) at top and bottom.
When changing the module online, connect the optional online connectors
(A6CON-LJ5P) between the connector and plugs.
When using the module at either end of the CC-Link system, fit the optional
one-touch connector plug with termination resistor (110Ω) (A6CON-TR11).
6) Connector for power supply and One-touch connector for module power supply line, and FG.
FG When carrying out jumper wiring, connect two optional one-touch connector
plugs for power supply/FG at top and bottom. Two different types (A6CON-
PW5P, A6CON-PW5P-SOD) are available as the one-touch connector plugs
for power supply and FG.
When not carrying out jumper wiring, also connect the plugs (for safety and
dust prevention).
When changing the module online, connect the optional online connectors
(A6CON-PWJ5P) between the connector and plugs.
7) 2-piece spring clamp terminal 2-piece terminal block for I/O signals.
block
8) DIN rail hook Hook to install the module to the DIN rail or connector type Metal installation
fitting (option). When mounting the module to a DIN rail, push in the DIN rail
hook until it clicks.
9) Mounting bracket (accessory) Used to install the module to a control panel.
10)
2 To operate the indication selector switch, do not use a tool such as a screwdriver. Doing so may damage the switch.

2 - 23 2 - 23
2 NAMES AND SETTINGS FOR EACH PART
MELSEC-A

AJ65VBTCE -8 (Sensor connector (e-CON) type 8 points module)

1 40 S
T
2 20 A
3 10 T 9)
4) 4 8
I
O
5 4 N CON ON

6 2 N A
1
2
3
4
7 1 O.
5)
5
6
7

8 4 B
R
B
8
9
10

3) 9 2 A
T
40
20
S
T

10 1
A
10
E C T
I

10)
8 O

6)
4 N
2 N
1 O.
D 4 B
R
2 A
1 T
E

A J65VBTCE3-8D
PW
X0 L RUN
L ERR.
X1
0
X2
1
2
1)
3
7) X3 4
5

10)
6
X4 7

X5

X6

X7

9) 8)

AJ65VBTCE -16 (Sensor connector (e-CON) type 16 points module)

1) 7) 10)
ON
PW L RUN L ERR. AJ65VBTCE3-16D
1 2 4 1 2 4 8102040
B RATE STATION NO.

4) 0 1 2 3 4 5 6 7

3)
8 9 A B C D E F

9)
X 0 1 2 3 4 5 6 7

8)
CON A B C D X 8 9 A B C D E F

9) 10) 5) 6) 8)

AJ65VBTCE -32 (Sensor connector (e-CON) type 32 points module)

1) 2) 7) 10)
ON
PW L RUN L ERR. AJ65VBTCE3-32D
1 2 4 1 2 4 8 102040

4)
B RATE STATI ON NO.

0 1 2 3 4 5 6 7

3)
8 9 A B C D E F

X 0 1 2 3 4 5 6 7 8 9 A B C D E F 9)

8)
CON A B C D X 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F

9) 5) 6) 8) 8)
10)

2 - 24 2 - 24
2 NAMES AND SETTINGS FOR EACH PART
MELSEC-A

No. Item Description

1) Operating status indicator LED LED name Details
On: Power being supplied
PW
Off: No power supplied
On: Normal communication
L RUN
Off: No communication (timeout error)
On: Communication error
Flashing regularly:
The station number or transmission speed switch setting
is changed while power is on.
L ERR. Flashing irregularly:
The terminating resistor setting is incorrect.
The module or CC-Link dedicated cable is affected by
noise.
Off: Normal communication
On: Input/output ON
0 to F
Off: Input/output OFF
*1
2) Indication selector switch When the switch is set to "F", LEDs indicate the ON/OFF status of the first 16
points.
When the switch is set to "L", LEDs indicate the ON/OFF status of the latter 16
points.
3) Transmission speed setting switch
Switch status Transmission
Setting
4 2 1 speed
0 OFF OFF OFF 156kbps
1 OFF OFF ON 625kbps
2 OFF ON OFF 2.5 Mbps
3 OFF ON ON 5.0 Mbps
4 ON OFF OFF 10 Mbps

Set the transmission speed within the above range.

4) Station number setting switch Select "10", "20", or "40" for the tens place.
Select "1", "2", "4", or "8" for the ones place.
*1
Set the station number within the range of 1 to 64.
Station Tens place Ones place
number 40 20 10 8 4 2 1
1 OFF OFF OFF OFF OFF OFF ON
2 OFF OFF OFF OFF OFF ON OFF
3 OFF OFF OFF OFF OFF ON
4 OFF OFF OFF OFF OFF OFF OFF
: : : : : : : :
10 OFF OFF ON OFF OFF OFF OFF
11 OFF OFF ON OFF OFF OFF ON
: : : : : : : :
64 ON ON OFF OFF ON OFF OFF

(Example) Setting the station number to 32:

Station Tens place Ones place
number 40 20 10 8 4 2 1
32 OFF ON ON OFF OFF ON OFF

1 A unique station number should be set.

2 - 25 2 - 25
2 NAMES AND SETTINGS FOR EACH PART
MELSEC-A

No. Item Description

5) Connector for communication One-touch connector for communication line.
When carrying out wiring, connect two optional one-touch connector plugs for
communication (A6CON-L5P) at top and bottom.
When changing the module online, connect the optional online connectors
(A6CON-LJ5P) between the connector and plugs.
When using the module at either end of the CC-Link system, fit the optional
one-touch connector plug with termination resistor (110Ω) (A6CON-TR11).
6) Connector for power supply and One-touch connector for module power supply line, I/O power supply line, and
FG FG.
When carrying out jumper wiring, connect two optional one-touch connector
plugs for power supply/FG at top and bottom. Two different types (A6CON-
PW5P, A6CON-PW5P-SOD) are available as the one-touch connector plugs
for power supply and FG.
When not carrying out jumper wiring, also connect the plugs (for safety and
dust prevention).
When changing the module online, connect the optional online connectors
(A6CON-PWJ5P) between the connector and plugs.
7) Connector for I/O Connector for I/O signals.
8) DIN rail hook Hook to install the module to the DIN rail or connector type Metal installation
fitting (option). When mounting the module to a DIN rail, push in the DIN rail
hook until it clicks.
9) Mounting bracket (accessory) Used to install the module to a control panel.
10) (Can be attached in two different ways, 9) and 10).)
Holding fixtures for screw installation are removal.

2 - 26 2 - 26
 3 SPECIFICATIONS
MELSEC-A

3 SPECIFICATIONS
This section explains the compact Remote I/O Module general specifications.

Item Specifications
6
Operating ambient temperature 0 to 55°C
6
Storage ambient temperature -20 to 75°C
10 to 90% RH, No condensation
Operating ambient humidity 4
(The waterproof type remote I/O module is compliant with IP67. )
Storage ambient humidity 10 to 90% RH, No condensation
Constant Half
Frequency Sweep Count
3 acceleration amplitude
Compliant When there is 5 to 8.4Hz — 3.5mm 10 times each
with JIS B intermittent in X, Y and Z
Vibration resistance 8.4 to 150Hz 9.8m/s
2
—
3502, vibration axis
IEC 61131-2 When there is
5 to 8.4Hz — 1.75mm
continuous 2
—
vibration 8.4 to 150Hz 4.9m/s —
2
Shock resistance Compliant with JIS B 3502, IEC 61131-2 (147m/s , 3 times in each of 3 directions X,Y,Z)
Operating environment No corrosive gas present
3
Operating height 0 to 2000m
5
Installation area On the control board
1
Over-voltage category II or less
2
Pollution rate 2 or less

1 Indicates the location where the device is connected from the public cable network to the
device structure wiring area.
Category II applies to the devices to which the power is supplied from a fixed equipment.
Surge withstand voltage for devices with up to 300V of rated voltage is 2500V.
2 This is an index which indicates the degree of conductive object generation in the
environment Pollution level 2 is when only non-conductive pollution occurs.
A temporary conductivity caused by condensation must be expected occasionally.
3 Do not use or store the programmable controller in the environment where the pressure is
higher than the atmospheric pressure at sea level. Otherwise, malfunction may result. To use
the programmable controller in high-pressure environment, contact your nearest Mitsubishi
representative.
4 Applicable only when all waterproof connectors are being used, or when waterproof caps are
installed on unused waterproof connectors or feed-through tubes. (Feed-through tubes are
used in the AJ65SBTW -16 only.)
5 It can also be used in an environment other than on the control panel if the conditions such as
usage ambient temperature and humidity are satisfied.
6 In the case of the waterproof remote I/O module, usage ambient temperature and storage
ambient temperature are the following. (AJ65SBTW -16 only)
Item Specification
Usage ambient temperature 0 to 45°C
Not wired (individual product) -20 to 65°C
Storage ambient temperature
Wired (after cable installation) -10 to 55°C

REMARK
For compliance of this product with the EMC and Low Voltage Directives, refer to the
user's manual for the CPU module used.

3-1 3-1
3 SPECIFICATIONS
MELSEC-A

MEMO

3-2 3-2
 4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

4 SPECIFICATIONS FOR INPUT MODULES

This chapter describes the specifications for a input module that can be connected to
the CC-Link system.

4.1 Terminal Block Type Input Module

4.1.1 AJ65SBTB2N-8A 100VAC input module

Type AC input module

Item AJ65SBTB2N-8A Appearance
Number of input points 8 points
Isolation method Photocoupler
Rated input voltage/rated frequency 100 to 120VAC, 50/60Hz
Rated input current Approx. 7mA (at 100VAC, 60Hz)
Operating voltage range 85 to 132VAC (50/60Hz ±3Hz, ripple ratio: within 5%)
4 Max. number of simultaneous input 100% (at 110VAC)
points 60% (at 132VAC)
Max. inrush current 200mA within 1ms (at 132VAC)
ON voltage/ON current 80VAC or higher/3.5mA or higher
OFF voltage/OFF current 30VAC or lower/1.7mA or lower
Input resistance Approx.15kΩ at 60Hz, approx.18kΩ at 50Hz
Response time OFF→ON 20ms or less (at 100VAC, 60Hz)
ON→OFF 20ms or less (at 100VAC, 60Hz)

COMB COMB COMB COMB COMB COMB COMB COMB COMB

X0 1 2 3 4 5 6 7
Wiring method for common 8 points/common (2-wire, terminal block type)

X7 COMA
Number of occupied stations 32-point assignment/station (8 points used)
Module power supply Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

X6
Current 35mA or lower (at 24VDC and all points ON)
Noise immunity Noise voltage: 1500Vp-p (AC type), 500Vp-p (DC type), noise width 1µs,

X5
noise frequency 25 to 60Hz (noise simulator condition)

X4
Fast transient/burst immunity test IEC 61000-4-4:1kV
Withstand voltage 1780VACrms for 3 cycles between all AC external terminals and ground X3

(2000m above sea level)

B RATE

X2
40 20 10 8 4 2 1 4 2 1

500VAC for 1 minute between all DC external terminals and ground

X1

Insulation resistance 10MΩ or higher between all AC external terminals and ground (500VDC
STATION NO.

insulation resistance tester)

X0

10MΩ or higher between all DC external terminals and ground (500VDC

insulation resistance tester)
(FG)
24G
ON

Weight 0.20kg
AJ65SBTB2N-8A

DA DG +24V

External Communication part, 7-point two-piece terminal block

SLD

connection module power supply part [Transmission circuit, module power supply, FG]
DB

system M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)

Applicable solderless terminal: 2 or less
I/O power supply part, 18-point direct-mount terminal block
I/O part [I/O power supply, I/O signal]
M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
Module mounting screw M4 screw with plain washer finished round
(tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable solderless terminal y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

4-1 4-1
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
TB2 DB
1 DA
2 DB TB3 DG
3 DG Insulation TB4 SLD
4 SLD
TB5 +24V
5 +24V
6 FG TB6 (FG)
7 24G TB7 24G
Module power supply
TB8 X0
8 X0 TB9 COM B
9 COM B TB10 X1
10 X1
11 COM B TB11 COM B
12 X2 TB12 X2
13 COM B TB13 COM B
14 X3
15 COM B TB14 X3
16 X4 TB15 COM B
17 COM B TB16 X4
18 X5
19 COM B TB17 COM B
20 X6
21 COM B
TB18 X5 4
TB19 COM B
22 X7
23 COM B TB20 X6
24 COM A TB21 COM B
25 COM B TB22 X7
100VAC
TB23 COM B
TB24 COM A
TB25 COM B
All COM B terminals are connected inside the module (shared common).

4-2 4-2
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

4.1.2 AJ65SBTB2N-16A 100VAC input module

Type AC input module
Item AJ65SBTB2N-16A Appearance
Number of input points 16 points
Isolation method Photocoupler
Rated input voltage/rated frequency 100 to 120VAC, 50/60Hz
Rated input current Approx. 7mA (at 100VAC, 60Hz)
Operating voltage range 85 to 132VAC (50/60Hz ±3Hz, ripple ratio: within 5%)
Max. number of simultaneous input 100% (at 110VAC),
points 60% (at 132VAC)
Max. inrush current 200mA within 1ms (at 132VAC)
ON voltage/ON current 80VAC or higher/5mA or higher
OFF voltage/OFF current 30VAC or lower/1.7mA or lower
Input resistance Approx.15kΩ at 60Hz, approx.18kΩ at 50Hz

COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB
X8 9 A B C D E F

COMA
Response time OFF→ON 20ms or less (at 100VAC, 60Hz)

XF
ON→OFF 20ms or less (at 100VAC, 60Hz)

XE
Wiring method for common 16 points/common (2-wire, terminal block type)

PW L RUN L ERR. X0 1 2 3 4 5 6 7

XD
Number of occupied stations 32-point assignment/station (16 points used)

XC
Module power supply Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

XB
Current 40mA or lower (at 24VDC and all points ON)

XA
Noise immunity Noise voltage: 1500Vp-p (AC type), 500Vp-p (DC type), noise width 1µs,

X9
noise frequency 25 to 60Hz (noise simulator condition)

X8
Fast transient/burst immunity test IEC61000-4-4:1kV

X7
Withstand voltage 1780VACrms for 3 cycles between all AC external terminals and ground (2000m above

X6
sea level)

X5
500VAC for 1 minute between all DC external terminals and ground

X4
Insulation resistance 10MΩ or higher between all AC external terminals and ground (500VDC insulation
resistance tester)

X3
B RATE
40 20 10 8 4 2 1 4 2 1
10MΩ or higher between all DC external terminals and ground (500VDC insulation

X2
resistance tester)

X1
STATION NO.
Weight 0.25kg

X0
External Communication part, 7-point two-piece terminal block

(FG)
24G
ON
connection module power supply part [Transmission circuit, module power supply, FG]

AJ65SBTB2N-16A

DG +24V
system M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)

SLD
Applicable solderless terminal: 2 or less

DB
I/O power supply part, 34-point direct-mount terminal block DA

I/O part [I/O power supply, I/O signal]

M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
Module mounting screw M4 screw with plain washer finished round (tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable solderless terminal y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

4-3 4-3
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
TB2 DB
1 DA TB3 DG
2 DB TB4 SLD
3 DG Insulation
TB5 +24V
4 SLD
5 +24V TB6 (FG)
6 FG TB7 24G
7 24G TB8 X0
Module power supply
TB9 COM B
8 X0 TB10 X1
9 COM B TB11 COM B
10 X1 TB12 X2
11 COM B
TB13 COM B
12 X2
13 COM B TB14 X3
14 X3 TB15 COM B
15 COM B TB16 X4
16 X4
TB17 COM B
17 COM B
18 X5 TB18 X5
19 COM B TB19 COM B
20 X6 TB20 X6
21 COM B TB21 COM B
22 X7
TB22 X7
23 COM B
24 X8 TB23 COM B
25 COM B TB24 X8
26 X9 TB25 COM B
27 COM B TB26 X9
28 XA
TB27 COM B
29 COM B
30 XB TB28 XA
31 COM B TB29 COM B
32 XC TB30 XB
33 COM B
TB31 COM B
34 XD
35 COM B
TB32 XC
36 XE TB33 COM B
37 COM B TB34 XD
38 XF TB35 COM B
39 COM B
TB36 XE
40 COM A
41 COM B TB37 COM B
TB38 XF
100VAC
TB39 COM B
TB40 COM A
TB41 COM B
All COM B terminals are connected inside the module (shared common).

4-4 4-4
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

4.1.3 AJ65SBTB1-8D 24VDC input module (positive common (sink), negative common
(source) loading)
Type DC input module
Item AJ65SBTB1-8D Appearance
Number of input points 8 points
Isolation method Photocoupler
Rated input voltage 24VDC
Rated input current Approx. 7mA
Operating voltage range 19.2 to 26.4VDC (ripple ratio: within 5%)
Max. number of simultaneous 100%
input points
ON voltage/ON current 14VDC or higher/3.5mA or higher
OFF voltage/OFF current 6VDC or lower/1.7mA or lower
Input resistance Approx. 3.3kΩ
Response time OFF→ON 1.5ms or less (at 24VDC)
ON→OFF 1.5ms or less (at 24VDC)

COM
COM
Wiring method for common 8 points/common (2 points) (1-wire, terminal block type)

B RATE
40 20 10 8 4 2 1 4 2 1

X7
Input type Positive/negative common shared type (sink/source shared type)

X6
Number of occupied stations 32-point assignment/station (8 points used)

X5
STATION NO.

X4
Module power supply Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

X3
Current 30mA or lower (at 24VDC and all points ON)

X2
Noise immunity Noise voltage 500Vp-p, noise width 1µs,

X1
ON
noise frequency 25 to 60Hz (DC type noise simulator condition)

X0
X0 1 2 3 4 5 6 7
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
Insulation resistance 10MΩ or higher between all DC external terminals and ground (500VDC

A J65SBTB1-8D
24G
(FG)
insulation resistance tester)
Protection degree IP2X

+24V
Weight 0.14kg

SLD
DG
External Communication part, 7-point two-piece terminal block [Transmission circuit, module power supply, FG]

DB
connection module power supply M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)

DA
system part Applicable solderless terminal: 2 or less
I/O power supply 10-point direct-mount terminal block [I/O power supply, I/O signal]
part, M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
I/O part Applicable solderless terminal: 2 or less
Module mounting screw M4 screw with plain washer finished round
(tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable solderless terminal y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
y V2-MS3, RAP2-3SL, TGV2-3N
2
[Applicable wire size: 1.25 to 2.0mm ]
Accessory User’s manual
External connection
Terminal number Signal name
TB1 DA
1 DA TB2 DB
2 DB TB3 DG
3 DG Insulation TB4 SLD
4 SLD
TB5 +24V
5 +24V
6 FG
TB6 (FG)
7 24G TB7 24G
Module power supply TB8 X0
8 X0 TB9 X1
9 X1 TB10 X2
10 X2 TB11 X3
11 X3
TB12 X4
12 X4
13 X5
TB13 X5
14 X6 TB14 X6
15 X7 TB15 X7
16 COM
TB16 COM
17 COM
TB17 COM

4-5 4-5
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

4.1.4 AJ65SBTB3-8D 24VDC input module (positive common (sink), negative common
(source) loading)
Type DC input module
Item AJ65SBTB3-8D Appearance
Number of input points 8 points
Isolation method Photocoupler
Rated input voltage 24VDC
Rated input current Approx. 7mA
Operating voltage range 19.2 to 26.4VDC (ripple ratio: within 5%)
Max. number of simultaneous input 100%
points
ON voltage/ON current 14VDC or higher/3.5mA or higher
OFF voltage/OFF current 6VDC or lower/1.7mA or lower

COMA COMB COMA COMB COMA COMB COMA COMB DC24B

Input resistance Approx. 3.3kΩ

DC24A
B RATE
40 20 10 8 4 2 1 4 2 1
Response time OFF→ON 1.5ms or less (at 24VDC)

X7
ON→OFF 1.5ms or less (at 24VDC)

STATION NO.
Wiring method for common 8 points/common (3-wire, terminal block type)

X6
Input type Positive/negative common shared type (sink/source shared type)
Supply current for connected device 1.0A or lower/common

X5
Number of occupied stations 32-point assignment/station (8 points used)

ON

X4
Module power supply Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
Current 40mA or lower (at 24VDC and all points ON)

X3
Noise immunity Noise voltage 500Vp-p, noise width 1µs,

X2
noise frequency 25 to 60Hz (DC type noise simulator condition)

AJ65SBTB3-8D
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

X1
Insulation resistance 10MΩ or higher between all DC external terminals and ground (500VDC
insulation resistance tester)

X0
X0 1 2 3 4 5 6 7
Protection degree IP2X
Weight 0.18kg

(FG)
24G
External Communication part, 7-point two-piece terminal block [Transmission circuit, module power supply, FG]
connection module power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)

DA DG +24V
system Applicable solderless terminal: 2 or less

SLD
I/O power supply part, 18-point direct-mount terminal block [I/O power supply, I/O signal]
I/O part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)

DB
Applicable solderless terminal: 2 or less
Module mounting screw M4 screw with plain washer finished round
(tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable solderless terminal y RAV1.25-3 (compliant with JIS C 2805)
2
[Applicable wire size: 0.3 to 1.25mm ]
y V2-MS3, RAP2-3SL, TGV2-3N
2
[Applicable wire size: 1.25 to 2.0mm ]
Accessory User’s manual
External connection
Terminal number Signal name
TB1 DA
1 DA
TB2 DB
2 DB
TB3 DG
3 DG Insulation
4 SLD
TB4 SLD
5 +24V TB5 +24V
6 FG TB6 (FG)
7 24G TB7 24G
Module power supply TB8 X0
Black TB9 COM A
3-wire sensor 8 X0
Brown TB10 X1
9 COM A
Blue TB11 COM B
10 X1
11 COM B TB12 X2
2-wire sensor Blue
Brown 12 X2 TB13 COM A
13 COM A TB14 X3
14 X3 TB15 COM B
15 COM B TB16 X4
16 X4 TB17 COM A
17 COM A
TB18 X5
18 X5
TB19 COM B
19 COM B
20 X6
TB20 X6
21 COM A TB21 COM A
22 X7 TB22 X7
23 COM B TB23 COM B
24 DC24A TB24 DC24A
25 DC24B TB25 DC24B

4-6 4-6
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

4.1.5 AJ65SBTB1-16D 24VDC input module (positive common (sink), negative common
(source) loading)
Type DC input module
Item AJ65SBTB1-16D Appearance
Number of input points 16 points
Isolation method Photocoupler
Rated input voltage 24VDC
Rated input current Approx. 7mA
Operating voltage range 19.2 to 26.4VDC (ripple ratio: within 5%)
Max. number of simultaneous input 100%
points
ON voltage/ON current 14VDC or higher/3.5mA or higher

COM
OFF voltage/OFF current 6VDC or lower/1.7mA or lower

COM
B RATE
40 20 10 8 4 2 1 4 2 1
Input resistance

XF
Approx. 3.3kΩ

XE
Response time OFF→ON 1.5ms or less (at 24VDC)

XD
STATION NO.
ON→OFF 1.5ms or less (at 24VDC)

XC
Wiring method for common 16 points/common (2 points) (1-wire, terminal block type)

XB
Input type Positive/negative common shared type (sink/source shared type)

XA
Number of occupied stations 32-point assignment/station (16 points used)

X9
ON
Module power supply Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

X8
X7
Current 35mA or lower (at 24VDC and all points ON)

X6
Noise immunity Noise voltage 500Vp-p, noise width 1µs,

X8 9 A B C D E F

X5
noise frequency 25 to 60Hz (DC type noise simulator condition)

X4
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

AJ65SBTB1-16D

X3
Insulation resistance 10MΩ or higher between all DC external terminals and ground (500VDC

X2
insulation resistance tester)

X1
Protection degree IP2X

X0
Weight 0.18kg

X0 1 2 3 4 5 6 7
External Communication part, 7-point two-piece terminal block
connection module power supply [Transmission circuit, module power supply, FG]

(FG)
24G
system part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less

+24V
I/O power supply part, 18-point direct-mount terminal block [I/O power supply, I/O signal]

SLD
I/O part M3×5.2 screw(tightening torque range: 0.59 to 0.88N•m)

DA DG
Applicable solderless terminal: 2 or less

DB
Module mounting screw M4 screw with plain washer finished round
(tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable solderless terminal y RAV1.25-3 (compliant with JIS C 2805)
2
[Applicable wire size: 0.3 to 1.25mm ]
y V2-MS3, RAP2-3SL, TGV2-3N
2
[Applicable wire size: 1.25 to 2.0mm ]
Accessory User’s manual
External connection
Terminal number Signal name
TB1 DA
1 DA TB2 DB
2 DB TB3 DG
3 DG Insulation TB4 SLD
4 SLD
TB5 +24V
5 +24V
TB6 (FG)
6 FG
7 24G
TB7 24G
Module power supply TB8 X0
TB9 X1
8 X0 TB10 X2
9 X1 TB11 X3
10 X2
TB12 X4
11 X3
TB13 X5
12 X4
13 X5
TB14 X6
14 X6 TB15 X7
15 X7 TB16 X8
16 X8 TB17 X9
17 X9 TB18 XA
18 XA TB19 XB
19 XB TB20 XC
20 XC TB21 XD
21 XD
TB22 XE
22 XE
TB23 XF
23 XF
TB24 COM
24 COM
25 COM
TB25 COM

4-7 4-7
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

4.1.6 AJ65SBTB1-16D1 24VDC input module (positive common (sink), negative common
(source) loading)
Type DC input module
Item AJ65SBTB1-16D1 Appearance
Number of input points 16 points
Isolation method Photocoupler
Rated input voltage 24VDC
Rated input current Approx. 5mA
Operating voltage range 19.2 to 26.4VDC (ripple ratio: within 5%)
Max. number of simultaneous input 100%
points
ON voltage/ON current 15VDC or higher/3mA or higher

COM
OFF voltage/OFF current 3VDC or lower/0.5mA or lower

COM
B RATE
40 20 10 8 4 2 1 4 2 1
Input resistance

XF
Approx. 4.7kΩ

XE
Response time OFF→ON 0.2ms or less (at 24VDC)

XD
STATION NO.
ON→OFF 0.2ms or less (at 24VDC)

XC
Wiring method for common 16 points/common (2 points) (1-wire, terminal block type)

XB
Input type Positive/negative common shared type (sink/source shared type)

XA
Number of occupied stations 32-point assignment/station (16 points used)

X9
ON
Module power supply Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

X8
X7
Current 40mA or lower (at 24VDC and all points ON)

X6
Noise immunity Noise voltage 500Vp-p, noise width 1µs,

X8 9 A B C D E F

X5
noise frequency 25 to 60Hz (DC type noise simulator condition)

X4
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

AJ65SBTB1-16D1

X3
Insulation resistance 10MΩ or higher between all DC external terminals and ground (500VDC

X2
insulation resistance tester)

X1
Protection degree IP2X

X0
Weight 0.18kg

X0 1 2 3 4 5 6 7
External Communication part, 7-point two-piece terminal block
connection module power supply [Transmission circuit, module power supply, FG]

(FG)
24G
system part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less

+24V
I/O power supply part, 18-point direct-mount terminal block [I/O power supply, I/O signal]

SLD
I/O part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)

DA DG
Applicable solderless terminal: 2 or less

DB
Module mounting screw M4 screw with plain washer finished round
(tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable solderless terminal y RAV1.25-3 (compliant with JIS C 2805)
2
[Applicable wire size: 0.3 to 1.25mm ]
y V2-MS3, RAP2-3SL, TGV2-3N
2
[Applicable wire size: 1.25 to 2.0mm ]
Accessory User’s manual
External connection
Terminal number Signal name
TB1 DA
1 DA
2 DB TB2 DB
3 DG TB3 DG
Insulation
4 SLD TB4 SLD
5 +24V TB5 +24V
6 FG TB6 (FG)
7 24G TB7 24G
Module power supply
TB8 X0
8 X0
TB9 X1
9 X1 TB10 X2
10 X2 TB11 X3
11 X3 TB12 X4
12 X4 TB13 X5
13 X5 TB14 X6
14 X6 TB15 X7
15 X7 TB16 X8
16 X8 TB17 X9
17 X9
TB18 XA
18 XA
TB19 XB
19 XB
20 XC
TB20 XC
21 XD TB21 XD
22 XE TB22 XE
23 XF TB23 XF
24 COM TB24 COM
25 COM TB25 COM

4-8 4-8
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

4.1.7 AJ65SBTB3-16D 24VDC input module (positive common (sink), negative common
(source) loading)
Type DC input module
Item AJ65SBTB3-16D Appearance
Number of input points 16 points
Isolation method Photocoupler
Rated input voltage 24VDC
Rated input current Approx. 7mA
Operating voltage range 19.2 to 26.4VDC (ripple ratio: within 5%)
Max. number of simultaneous input points 100%
ON voltage/ON current 14VDC or higher/3.5mA or higher
OFF voltage/OFF current 6VDC or lower/1.7mA or lower

COMA COMB COMA COMB COMA COMB COMA COMB COMA COMB COMA COMB COMA COMB COMA COMB DC24B
Input resistance Approx. 3.3kΩ

DC24A
B RATE
40 20 10 8 4 2 1 4 2 1
Response time OFF→ON 1.5ms or less (at 24VDC)

XF
STATION NO.
ON→OFF 1.5ms or less (at 24VDC)

XE
Wiring method for common 16points/common (3-wire, terminal block type)

XD
Input type Positive/negative common shared type (sink/source shared type)

ON

XC
Supply current for connected device 1.0A or lower/common

XB
Number of occupied stations 32-point assignment/station (16points used)

XA
Module power supply Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

X9
Current 45mA or lower (at 24VDC and all points ON)

X8
X7
Noise immunity Noise voltage 500Vp-p, noise width 1µs,

X6
noise frequency 25 to 60Hz (DC type noise simulator condition)

X5
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

X4
Insulation resistance 10MΩ or higher between all DC external terminals and ground (500VDC insulation
resistance tester)

X3
X8 9 A B C D E F

X2
Protection degree IP2X

AJ65SBTB3-16D
X1
Weight 0.25kg

X0
External Communication part, 7-point two-piece terminal block [Transmission circuit, module power supply, FG]

PW L RUN L ERR. X0 1 2 3 4 5 6 7
connection module power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)

(FG)
24G
system Applicable solderless terminal: 2 or less

+24V
I/O power supply part, 34-point direct-mount terminal block [I/O power supply, I/O signal]

SLD
DG
I/O part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)

DB
DA
Applicable solderless terminal: 2 or less
Module mounting screw M4 screw with plain washer finished round (tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable solderless terminal y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

4-9 4-9
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
TB2 DB
1 DA TB3 DG
2 DB TB4 SLD
3 DG Insulation TB5 +24V
4 SLD
5 +24V
TB6 (FG)
6 FG TB7 24G
7 24G TB8 X0
Module power supply
TB9 COM A
Black TB10 X1
3-wire sensor 8 X0
Brown
9 COM A TB11 COM B
Blue
10 X1 TB12 X2
Blue 11 COM B
2-wire sensor TB13 COM A
Brown 12 X2
13 COM A
TB14 X3
14 X3 TB15 COM B
15 COM B TB16 X4
16 X4 TB17 COM A
17 COM A
TB18 X5
18 X5
19 COM B TB19 COM B
20 X6 TB20 X6
21 COM A TB21 COM A
22 X7 TB22 X7
23 COM B
24 X8
TB23 COM B
25 COM A TB24 X8
26 X9 TB25 COM A
27 COM B TB26 X9
28 XA
TB27 COM B
29 COM A
30 XB TB28 XA
31 COM B TB29 COM A
32 XC TB30 XB
33 COM A TB31 COM B
34 XD
TB32 XC
35 COM B
36 XE TB33 COM A
37 COM A TB34 XD
38 XF TB35 COM B
39 COM B TB36 XE
40 DC24A
TB37 COM A
41 DC24B
TB38 XF
TB39 COM B
TB40 DC24A
TB41 DC24B

4 - 10 4 - 10
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

4.1.8 AJ65SBTB3-16KD 24VDC input module (positive common (sink), negative common
(source) loading)

Type DC input module

Item AJ65SBTB3-16KD Appearance
Number of input points 16 points
Isolation method Photocoupler
Rated input voltage 24VDC
Rated input current Approx. 7mA
Operating voltage range 20.4 to 28.8VDC (ripple ratio: within 5%)
Max. number of simultaneous input points 100%
ON voltage/ON current 14VDC or higher/4mA or higher
OFF voltage/OFF current 5.5VDC or lower/1.7mA or lower
Input resistance Approx. 3.0kΩ
Response time Input response
0.2ms 1.5ms 5ms 10ms
speed
OFF→ON 0.2ms or less 1.5ms or less 5ms or less 10ms or less
ON→OFF 0.2ms or less 1.5ms or less 5ms or less 10ms or less
Wiring method for common 16 points/common (3-wire, terminal block type)
Input type Positive/negative common shared type (sink/source shared type)
Supply current for connected device 1.0A or lower/common
Number of occupied stations 32-point assignment/station (16 points used)
Module power supply Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
Current 50mA or lower (at 24VDC and all points ON)
Noise immunity Noise voltage 500Vp-p, noise width 1µs,
noise frequency 25 to 60Hz (DC type noise simulator condition)
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
Insulation resistance 10MΩ or higher between all DC external terminals and ground (500VDC insulation
resistance tester)
Protection degree IP2X
Weight 0.26kg
External Communication part, 7-point two-piece terminal block [Transmission circuit, module power supply, FG]
connection module power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
system Applicable solderless terminal: 2 or less
I/O power supply part, 34-point direct-mount terminal block [I/O power supply, I/O signal]
I/O part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
Module mounting screw M4 screw with plain washer finished round (tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable solderless terminal y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

4 - 11 4 - 11
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
TB2 DB
1 DA TB3 DG
2 DB
TB4 SLD
3 DG Insulation
4 SLD TB5 +24V
5 +24V TB6 (FG)
6 FG TB7 24G
7 24G
Module power supply TB8 X0
TB9 COM A
TB10 X1
Black TB11 COM B
3-wire sensor 8 X0
Brown
9 COM A TB12 X2
Blue
10 X1
TB13 COM A
Blue 11 COM B
2-wire sensor TB14 X3
Brown 12 X2
13 COM A TB15 COM B
14 X3 TB16 X4
15 COM B
TB17 COM A
16 X4
17 COM A
TB18 X5
18 X5 TB19 COM B
19 COM B TB20 X6
20 X6 TB21 COM A
21 COM A
22 X7
TB22 X7
23 COM B TB23 COM B
24 X8 TB24 X8
25 COM A
TB25 COM A
26 X9
TB26 X9
27 COM B
28 XA TB27 COM B
29 COM A TB28 XA
30 XB TB29 COM A
31 COM B
TB30 XB
32 XC
33 COM A TB31 COM B
34 XD TB32 XC
35 COM B
TB33 COM A
36 XE
TB34 XD
37 COM A
38 XF TB35 COM B
39 COM B TB36 XE
40 DC24A TB37 COM A
41 DC24B
TB38 XF
TB39 COM B
TB40 DC24A
TB41 DC24B

4 - 12 4 - 12
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

4.1.9 AJ65SBTB3-16D5 5VDC input module (positive common (sink), negative common
(source) loading)
Type DC input module
Item AJ65SBTB3-16D5 Appearance
Number of input points 16 points
Isolation method Photocoupler
Rated input voltage 5VDC
Rated input current Approx. 4mA
Operating voltage range 4.25 to 6VDC (ripple ratio: within 5%)
Max. number of simultaneous input 100%
points
ON voltage/ON current 3.5VDC or higher/2mA or higher
OFF voltage/OFF current 1.5VDC or lower/1mA or lower

STATI ON NO.
Input resistance Approx. 1.0kΩ
Response time OFF→ON 1.5ms or less (at 5VDC)
ON→OFF 1.5ms or less (at 5VDC)
Wiring method for common 16 points/common (3-wire, terminal block type)
Input type Positive/negative common shared type (sink/source shared type)
Supply current for connected device 1.0A or lower/common
Number of occupied stations 32-point assignment/station (16 points used)
Module power supply Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
Current 30mA or lower (at 24VDC and all points ON)
Noise immunity Noise voltage 500Vp-p, noise width 1µs,
noise frequency 25 to 60Hz (DC type noise simulator condition)
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
Insulation resistance 10MΩ or higher between all DC external terminals and ground (500VDC insulation
resistance tester)
Protection degree IP2X
Weight 0.25kg
External Communication part, 7-point two-piece terminal block [Transmission circuit, module power supply, FG]
connection module power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)

A
system Applicable solderless terminal: 2 or less
I/O power supply part, 34-point direct-mount terminal block [I/O power supply, I/O signal]
I/O part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
Module mounting screw M4 screw with plain washer finished round (tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable solderless terminal y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

4 - 13 4 - 13
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
1 DA
2 DB TB2 DB
3 DG Insulation TB3 DG
4 SLD TB4 SLD
5 +24V
6 FG
TB5 +24V
7 24G TB6 (FG)
Module power supply TB7 24G
TB8 X0
TB9 COM A
TTL, LS-TTL, or CMOS buffer 8 X0
9 COM A TB10 X1
10 X1 TB11 COM B
11 COM B TB12 X2
Open collector 12 X2
TB13 COM A
13 COM A
14 X3 TB14 X3
15 COM B TB15 COM B
16 X4
TB16 X4
17 COM A
18 X5 TB17 COM A
19 COM B TB18 X5
20 X6 TB19 COM B
21 COM A
22 X7
TB20 X6
23 COM B TB21 COM A
24 X8 TB22 X7
25 COM A
TB23 COM B
26 X9
27 COM B TB24 X8
28 XA TB25 COM A
29 COM A
TB26 X9
30 XB
31 COM B
TB27 COM B
32 XC TB28 XA
33 COM A TB29 COM A
34 XD
TB30 XB
35 COM B
36 XE TB31 COM B
37 COM A TB32 XC
TTL, LS-TTL, or CMOS buffer 38 XF
TB33 COM A
39 COM B
1 TB34 XD
40 DC5A
41 DC5B TB35 COM B
TB36 XE
TB37 COM A
TB38 XF
TB39 COM B
TB40 DC5A
TB41 DC5B

2
For TTL, LS-TTL, or CMOS buffer (positive common) connection For a sensor (negative common) connection

COM B
COM A

X0 X0

COM B
COM A
Detection circuit

1: Polarity to connect an external power supply for TTL, LS-TTL, and CMOS buffer (positive common) connection.
For a sensor (negative common) connection, connect the negative pole to DC5A and the positive pole to DC5B.
2: For connection of TTL output (source type) sensor, use a sensor with a built-in pull-up resistor or provide a pull-up resistor in the circuit.

4 - 14 4 - 14
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

4.1.10 AJ65SBTB1-32D 24VDC input module (positive common (sink), negative common
(source) loading)
Type DC input module
Item AJ65SBTB1-32D Appearance
Number of input points 32 points
Isolation method Photocoupler
Rated input voltage 24VDC
Rated input current Approx. 7mA
Operating voltage range 19.2 to 26.4VDC (ripple ratio: within 5%)
Max. number of simultaneous input 100%
points

X1F COM
ON voltage/ON current 14VDC or higher/3.5mA or higher

X1E COM
B RATE
40 20 10 8 4 2 1 4 2 1
OFF voltage/OFF current 6VDC or lower/1.7mA or lower

X1D
STATION NO.
Input resistance Approx. 3.3kΩ

X1C
X1B
Response time OFF→ON 1.5ms or less (at 24VDC)

X1A
X19
ON→OFF 1.5ms or less (at 24VDC)

X18
ON
Wiring method for common 32 points/common (2 points) (1-wire, terminal block type)

X17
X16
Input type Positive/negative common shared type (sink/source shared type)

X15
X14
Number of occupied stations 32-point assignment/station (32 points used)

X13
X12
Module power supply Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

X10 11 12 13 14 15 16 17 X18 19 1A1B 1C1D1E 1F

X11
Current 45mA or lower (at 24VDC and all points ON)

X10
XF
Noise immunity Noise voltage 500Vp-p, noise width 1µs,

XE
XD
noise frequency 25 to 60Hz (DC type noise simulator condition)

XC
XB
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

XA
Insulation resistance 10MΩ or higher between all DC external terminals and ground (500VDC insulation

X9
X8
resistance tester)

X7
X6
Protection degree IP2X

X8 9 A B C D E F

X5
Weight 0.25kg

X4
AJ65SBTB1-32D

X3
External Communication part, 7-point two-piece terminal block [Transmission circuit, module power supply, FG]

X2
X1
connection module power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)

X0
PW L RUN L ERR. X0 1 2 3 4 5 6 7
system Applicable solderless terminal: 2 or less
I/O power supply part, 34-point direct-mount terminal block [I/O power supply, I/O signal]

(FG)
24G
I/O part M3×5.2 screw(tightening torque range: 0.59 to 0.88N•m)

DA DG +24V
DB SLD
Applicable solderless terminal: 2 or less
Module mounting screw M4 screw with plain washer finished round
(tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable solderless terminal y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

4 - 15 4 - 15
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
TB2 DB
TB3 DG
1 DA
TB4 SLD
2 DB
3 DG Insulation TB5 +24V
4 SLD TB6 (FG)
5 +24V TB7 24G
6 FG TB8 X0
7 24G
Module power supply TB9 X1
8 X0 TB10 X2
9 X1 TB11 X3
10 X2 TB12 X4
11 X3
TB13 X5
12 X4
13 X5
TB14 X6
14 X6 TB15 X7
15 X7 TB16 X8
16 X8 TB17 X9
17 X9
TB18 XA
18 XA
19 XB TB19 XB
20 XC TB20 XC
21 XD TB21 XD
22 XE
TB22 XE
23 XF
24 X10 TB23 XF
25 X11 TB24 X10
26 X12 TB25 X11
27 X13 TB26 X12
28 X14
29 X15
TB27 X13
30 X16 TB28 X14
31 X17 TB29 X15
32 X18 TB30 X16
33 X19
TB31 X17
34 X1A
35 X1B TB32 X18
36 X1C TB33 X19
37 X1D TB34 X1A
38 X1E
TB35 X1B
39 X1F
40 COM
TB36 X1C
41 COM TB37 X1D
TB38 X1E
TB39 X1F
TB40 COM
TB41 COM

4 - 16 4 - 16
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

4.1.11 AJ65SBTB1-32KD 24VDC input module (positive common (sink), negative common
(source) loading)
Type DC input module
Item AJ65SBTB1-32KD Appearance
Number of input points 32 points
Isolation method Photocoupler
Rated input voltage 24VDC
Rated input current Approx. 7mA
Operating voltage range 20.4 to 28.8VDC (ripple ratio: within 5%)
Max. number of simultaneous input 100% (at 26.4VDC), 50% (at 28.8VDC)
points
ON voltage/ON current 14VDC or higher/4mA or higher
OFF voltage/OFF current 5.5VDC or lower/1.7mA or lower
Input resistance Approx. 3.0kΩ
Input response
0.2ms 1.5ms 5ms 10ms
speed
Response time
OFF→ON 0.2ms or less 1.5ms or less 5ms or less 10ms or less
ON→OFF 0.2ms or less 1.5ms or less 5ms or less 10ms or less
Wiring method for common 32 points/common (1-wire, terminal block type)
Input type Positive/negative common shared type (sink/source shared type)
Number of occupied stations 32-point assignment/station (32 points used)
Module power supply Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
Current 75mA or lower (at 24VDC and all points ON)
Noise immunity Noise voltage 500Vp-p, noise width 1µs,
noise frequency 25 to 60Hz (DC type noise simulator condition)
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
Insulation resistance 10MΩ or higher between all DC external terminals and ground (500VDC insulation
resistance tester)
Protection degree IP2X
Weight 0.26kg
External Communication part, 7-point two-piece terminal block [Transmission circuit, module power supply, FG]
connection module power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
system Applicable solderless terminal: 2 or less
I/O power supply part, 34-point direct-mount terminal block [I/O power supply, I/O signal]
I/O part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
Module mounting screw M4 screw with plain washer finished round
(tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable solderless terminal y RAV1.25-3 (compliant with JIS C 2805)
2
[Applicable wire size: 0.3 to 1.25mm ]
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

4 - 17 4 - 17
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
TB2 DB
TB3 DG
1 DA
2 DB TB4 SLD
3 DG Insulation TB5 +24V
4 SLD TB6 (FG)
5 +24V
TB7 24G
6 FG
7 24G TB8 X0
Module power supply TB9 X1
TB10 X2
TB11 X3
8 X0
TB12 X4
9 X1
10 X2
TB13 X5
11 X3 TB14 X6
12 X4 TB15 X7
13 X5
TB16 X8
14 X6
15 X7 TB17 X9
16 X8 TB18 XA
17 X9 TB19 XB
18 XA
TB20 XC
19 XB
20 XC TB21 XD
21 XD TB22 XE
22 XE TB23 XF
23 XF
TB24 X10
24 X10
25 X11 TB25 X11
26 X12 TB26 X12
27 X13 TB27 X13
28 X14
TB28 X14
29 X15
30 X16 TB29 X15
31 X17 TB30 X16
32 X18 TB31 X17
33 X19
TB32 X18
34 X1A
35 X1B TB33 X19
36 X1C TB34 X1A
37 X1D TB35 X1B
38 X1E
TB36 X1C
39 X1F
40 COM TB37 X1D
41 COM TB38 X1E
TB39 X1F
TB40 COM
TB41 COM

4 - 18 4 - 18
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

4.1.12 AJ65SBTB1-32D1 24VDC input module (positive common (sink), negative common
(source) loading)
Type DC input module
Item AJ65SBTB1-32D1 Appearance
Number of input points 32 points
Isolation method Photocoupler
Rated input voltage 24VDC
Rated input current Approx. 5mA
Operating voltage range 19.2 to 26.4VDC (ripple ratio: within 5%)
Max. number of simultaneous input 100%
points

X1F COM
ON voltage/ON current 15VDC or higher/3mA or higher

X1E COM
B RATE
40 20 10 8 4 2 1 4 2 1
OFF voltage/OFF current 3VDC or lower/0.5mA or lower

X1D
STATION NO.
Input resistance Approx. 4.7kΩ

X1C
X1B
Response time OFF→ON 0.2ms or less (at 24VDC)

X1A
X19
ON→OFF 0.2ms or less (at 24VDC)

X18
ON
Wiring method for common 32 points/common (2 points) (1-wire, terminal block type)

X17
X16
Input type Positive/negative common shared type (sink/source shared type)

X15
X14
Number of occupied stations 32-point assignment/station (32 points used)

X13
X12
Module power supply Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

X10 11 12 13 14 15 16 17 X18 19 1A1B 1C1D1E 1F

X11
Current 50mA or lower (at 24VDC and all points ON)

X10
XF
Noise immunity Noise voltage 500Vp-p, noise width 1µs,

XE
XD
noise frequency 25 to 60Hz (DC type noise simulator condition)

XC
XB
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

XA
Insulation resistance 10MΩ or higher between all DC external terminals and ground (500VDC

X9
X8
insulation resistance tester)

X7
X6
Protection degree IP2X

X8 9 A B C D E F

X5
Weight 0.25kg

X4
AJ65SBTB1-32D1

X3
External Communication part, 7-point two-piece terminal block [Transmission circuit, module power supply, FG]

X2
X1
connection module power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)

X0
PW L RUN L ERR. X0 1 2 3 4 5 6 7
system Applicable solderless terminal: 2 or less
I/O power supply part, 34-point direct-mount terminal block [I/O power supply, I/O signal]

(FG)
24G
I/O part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
DA DG +24V
DB SLD
Applicable solderless terminal: 2 or less
Module mounting screw M4 screw with plain washer finished round
(tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable solderless terminal y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

4 - 19 4 - 19
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
TB2 DB
1 DA
TB3 DG
2 DB
3 DG TB4 SLD
Insulation
4 SLD TB5 +24V
5 +24V TB6 (FG)
6 FG TB7 24G
7 24G TB8 X0
Module power supply
TB9 X1
8 X0 TB10 X2
9 X1 TB11 X3
10 X2 TB12 X4
11 X3
TB13 X5
12 X4
13 X5 TB14 X6
14 X6 TB15 X7
15 X7 TB16 X8
16 X8 TB17 X9
17 X9 TB18 XA
18 XA
TB19 XB
19 XB
20 XC TB20 XC
21 XD TB21 XD
22 XE TB22 XE
23 XF TB23 XF
24 X10 TB24 X10
25 X11
TB25 X11
26 X12
27 X13 TB26 X12
28 X14 TB27 X13
29 X15 TB28 X14
30 X16 TB29 X15
31 X17 TB30 X16
32 X18
TB31 X17
33 X19
34 X1A TB32 X18
35 X1B TB33 X19
36 X1C TB34 X1A
37 X1D TB35 X1B
38 X1E TB36 X1C
39 X1F
TB37 X1D
40 COM
41 COM TB38 X1E
TB39 X1F
TB40 COM
TB41 COM

4 - 20 4 - 20
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

4.1.13 AJ65SBTB1-32D5 5VDC input module (positive common (sink), negative common
(source) loading)
Type DC input module
Item AJ65SBTB1-32D5 Appearance
Number of input points 32 points
Isolation method Photocoupler
Rated input voltage 5VDC
Rated input current Approx. 4mA
Operating voltage range 4.25 to 6VDC (ripple ratio: within 5%)
Max. number of simultaneous input 100%
points
ON voltage/ON current 3.5VDC or higher/2mA or higher
OFF voltage/OFF current 1.5VDC or lower/1mA or lower
Input resistance Approx. 1.0kΩ
Response time OFF→ON 1.5ms or less (at 5VDC)
ON→OFF 1.5ms or less (at 5VDC)
Wiring method for common 32 points/common (1-wire, terminal block type)
Input type Positive/negative common shared type (sink/source shared type)
Number of occupied stations 32-point assignment/station (32 points used)
Module power supply Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
Current 35mA or lower (at 24VDC and all points ON)
Noise immunity Noise voltage 500Vp-p, noise width 1µs,
noise frequency 25 to 60Hz (DC type noise simulator condition)
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
Insulation resistance 10MΩ or higher between all DC external terminals and ground (500VDC
insulation resistance tester)
Protection degree IP2X
Weight 0.26kg
External Communication part, 7-point two-piece terminal block
connection module power supply part [Transmission circuit, module power supply, FG]
system M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
I/O power supply part, 34-point direct-mount terminal block [I/O power supply, I/O signal]
I/O part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
Module mounting screw M4 screw with plain washer finished round
(tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable solderless terminal y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

4 - 21 4 - 21
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
1 DA
2 DB TB2 DB
3 DG Insulation TB3 DG
4 SLD TB4 SLD
5 +24V
TB5 +24V
6 FG
7 24G TB6 (FG)
Module power supply TB7 24G
TB8 X0
TB9 X1
8 X0
Open collector (positive common) 9 X1 TB10 X2
10 X2 TB11 X3
11 X3
TB12 X4
12 X4
13 X5 TB13 X5
14 X6 TB14 X6
15 X7
TB15 X7
16 X8
17 X9 TB16 X8
18 XA TB17 X9
19 XB TB18 XA
20 XC
21 XD TB19 XB
22 XE TB20 XC
23 XF TB21 XD
24 X10
TB22 XE
25 X11
26 X12 TB23 XF
27 X13 TB24 X10
28 X14
TB25 X11
29 X15
30 X16 TB26 X12
31 X17 TB27 X13
32 X18
TB28 X14
33 X19
34 X1A TB29 X15
35 X1B TB30 X16
36 X1C TB31 X17
37 X1D
38 X1E TB32 X18
39 X1F TB33 X19
40 COM TB34 X1A
*1 41 COM
TB35 X1B
TB36 X1C
TB37 X1D
TB38 X1E
TB39 X1F
TB40 COM
TB41 COM

2
For TTL, LS-TTL, or CMOS buffer (positive common) connection For a sensor (negative common) connection

X0 X0

COM
COM

Detection circuit

1: Polarity to connect an external power supply for TTL, LS-TTL, and CMOS buffer (positive common) connection.
For a sensor (negative common) connection, connect the negative pole to COM.
2: For connection of TTL output (source type) sensor, use a sensor with a built-in pull-up resistor or provide a pull-up resistor in the circuit.

4 - 22 4 - 22
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

4.1.14 AJ65DBTB1-32D 24VDC input module (positive common (sink), negative common
(source) loading)
Type DC input module
Item AJ65DBTB1-32D Appearance
Number of input points 32 points
Isolation method Photocoupler
Rated input voltage 24VDC
Rated input current Approx. 5mA
Operating voltage range 20.4 to 31.2VDC (ripple ratio: within 5%)
Max. number of simultaneous input 100% (at 26.4VDC)
points
ON voltage/ON current 15VDC or higher/3mA or higher
OFF voltage/OFF current 5VDC or lower/1.5mA or lower
Input resistance Approx. 4.7kΩ
Response time OFF→ON 10ms or less (at 24VDC)
ON→OFF 10ms or less (at 24VDC)
Wiring method for common 16 points/common (2 points) (1-wire, terminal block type)
Input type Positive/negative common shared type (sink/source shared type)
Number of occupied stations 32-point assignment/station (32 points used)
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
supply Current 45mA or lower (at 24VDC and all points ON)
Noise immunity Noise voltage 500Vp-p, noise width 1µs,
noise frequency 25 to 60Hz (DC type noise simulator condition)
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
Insulation resistance 10MΩ or higher between all DC external terminals and ground (500VDC
insulation resistance tester)
Protection degree IP2X
Weight 0.6kg
External connection system 50-point terminal block
[Transmission circuit, module power supply, FG, I/O power supply, I/O signal]
M3.5×7 screw (tightening torque range: 0.68 to 0.92N•m)
Applicable solderless terminal: 2 or less
Module mounting screw M4 screw with plain washer finished round
(tightening torque range: 0.78 to 1.08N•m)
Applicable solderless terminal R1.25-3.5, RAV2-3.5 (compliant with JIS C 2805)
Accessory User’s manual
Part sold separately A6DIN1C, A2CCOM-TB

4 - 23 4 - 23
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection
Terminal Signal Terminal Signal
number name number name
TB1 DA TB26 Empty
TB2 DG TB27 Empty
TB3 DB TB28 +24V
Insulation
1 Empty 26
TB4 Empty DA TB29 Empty
2 DG Empty 27
TB5 SLD 3 DB +24V 28
24VDC
TB30 (FG)
4 Empty Empty 29
TB6 Empty 5 SLD FG 30
TB31 Empty
TB7 24G 6 Empty Empty 31 TB32 24G
7 24G 24G 32
TB8 X0 TB33 X10
Module power supply
TB9 X1 TB34 X11
8 X0 X10 33
TB10 X2 9 X1 X11 34
TB35 X12
TB11 X3 10 X2 X12 35 TB36 X13
11 X3 X13 36
TB12 X4 12 X4 X14 37 TB37 X14
TB13 X5 13 X5 X15 38 TB38 X15
14 X6 X16 39
TB14 X6 15 X7 X17 40 TB39 X16
16 COM1 COM3 41
TB15 X7 X18 42
TB40 X17
17 X8
TB16 COM1 18 X9 X19 43 TB41 COM3
19 XA X1A 44
TB17 X8 20 XB X1B 45 TB42 X18
TB18 X9 21 XC X1C 46 TB43 X19
22 XD X1D 47
TB19 XA 23 XE X1E 48 TB44 X1A
24 XF X1F 49
TB20 XB COM4 50
TB45 X1B
25 COM2
TB21 XC TB46 X1C
24VDC 24VDC
TB22 XD TB47 X1D
TB23 XE TB48 X1E
TB24 XF TB49 X1F
TB25 COM2 TB50 COM4

4 - 24 4 - 24
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

4.2 Spring Clamp Terminal Block Type Input Module

4.2.1 AJ65VBTS3-16D 24VDC input module (positive common (sink type))

Type DC input module
Item AJ65VBTS3-16D Appearance
Number of input points 16 points
Isolation method Photocoupler
Rated input voltage 24VDC
Rated input current Approx. 5mA
Operating voltage range 19.2 to 26.4VDC (ripple ratio: within 5%)
Max. number of simultaneous 100% or 75% (Refer to Section1.3.)
input points
ON voltage/ON current 14VDC or higher/3.5mA or higher
OFF voltage/OFF current 6VDC or lower/1.7mA or lower
Input resistance Approx. 4.7kΩ
Response OFF→ON 1.5ms or less (at 24VDC)
time ON→OFF 1.5ms or less (at 24VDC)
Wiring method for common 16 points/common (3-wire, spring clamp terminal block type)
Input type Positive common (sink type)

XF
Supply current for connected 1.0A or lower/common

XD XE
device
Number of occupied stations 32-point assignment/station (16points used)

XA XB XC
Module Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
power supply Current 35mA or lower (at 24VDC and all points ON)
Noise immunity Noise voltage 500Vp-p, noise width 1µs,

X9
noise frequency 25 to 60Hz (DC type noise simulator condition)

COM+
X8

COM-
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

AJ65VBTS3-16D

X7
Insulation resistance 10MΩ or higher between all DC external terminals and ground (500VDC insulation

X6
resistance tester)

X5
Protection degree IP1XB

X4
Weight 0.24kg
X2 X3
External Communication One-touch connector for communication [Transmission circuit] X1
connection part 5-pin IDC plug is sold separately: A6CON-L5P
X0

system <Optional>
COM+

COM-
Online connector for communication: A6CON-LJ5P
NC

Power supply One-touch connector for power supply and FG [Module power supply, FG]
part 5-pin IDC plug is sold separately: A6CON-PW5P, A6CON-PW5P-SOD
D
8 9 A B C DE F
0 1 2 3 4 5 6 7

<Optional>
L RUN L ERR.

Online connector for power supply: A6CON-PWJ5P

C

I/O part 2-piece spring clamp terminal block [I/O power supply, I/O signals]
ONPW

Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715) B RATE STATION NO.
1 2 4 1 2 4 8 1020 40

Applicable Connector for Applicable cable:

CON A

wire size communication FANC-110SBH, FA-CBL200PSBH, CS-110

Connector for 0.66 to 0.98mm2 (AWG18)
power supply and [φ2.2 to 3.0mm (A6CON-PW5P), φ2.0 to 2.3mm (A6CON-PW5P-SOD)]
FG Wire diameter: 0.16mm or more
Insulating coating material: PVC (heat-resistant)
Stranded wire 0.08 to 1.5mm2 (AWG28 to 16)
1
Spring clamp
terminal block for Wire strip length: 8 to 11mm
I/O
Applicable TE0.5 [Applicable wire size: 0.5mm2]
2
solderless TE0.75 [Applicable wire size: 0.75mm ]
terminal TE1 [Applicable wire size: 0.9 to 1.0mm2]
TE1.5 [Applicable wire size: 1.25 to 1.5mm2]
2
FA-VTC125T9 [Applicable wire size: 0.3 to 1.65mm ]
FA-VTCW125T9 [Applicable wire size: 0.3 to 1.65mm2]
Accessory User’s manual, Holding fixtures for screw installation

1: Insert one wire per terminal.

4 - 25 4 - 25
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection

CONA Pin number Signal name

1
1 DA
2
2 DB 1 DA
3
3 DG
4
4 Empty
2 DB
5
5 SLD CON A, B 3 DG
CONB
1
1 DA 4 Empty
2
2 DB
3 5 SLD
3 DG
4
5
4 Empty 1 (FG)
5 SLD
One-touch connector for communication 2 +24V (UNIT)
1
CONC Insulation CON C, D 3 24G (UNIT)
1 FG
2
3
2 +24V(UNIT) 4 Empty
3 24G(UNIT)
4 4 Empty 5 Empty
5
5 Empty
Terminal block
COND
1
1 FG Column A Column B Column C
2 2 +24V(UNIT)
3
3 24G(UNIT) 1 Empty 1 COM+ 1 COM-
4 4 Empty
5
5 Empty
2 X0 2 COM+ 2 COM-
1
One-touch connector for power supply and FG 3 X1 3 COM+ 3 COM-
TB1A Empty 4 X2 4 COM+ 4 COM-
TB1B COM+
TB1C COM- 5 X3 5 COM+ 5 COM-
Black
TB2A X0
Brown
TB2B COM+ 6 X4 6 COM+ 6 COM-
Blue
TB2C COM-
3-wire sensor Detection
Brown
TB3A X1
7 X5 7 COM+ 7 COM-
(sink output) circuit
Blue
TB3B COM+ 8 X6 8 COM+ 8 COM-
TB3C COM-
TB4A X2 9 X7 9 COM+ 9 COM-
TB4B COM+
TB4C COM- 10 X8 10 COM+ 10 COM-
2-wire sensor TB5A X3
(sink output) Detection TB5B COM+
11 X9 11 COM+ 11 COM-
circuit
TB5C COM- 12 XA 12 COM+ 12 COM-
TB6A X4
TB6B COM+ 13 XB 13 COM+ 13 COM-
TB6C COM-
TB7A X5 14 XC 14 COM+ 14 COM-
TB7B COM+
TB7C COM-
15 XD 15 COM+ 15 COM-
TB8A X6 16 XE 16 COM+ 16 COM-
TB8B COM+
TB8C COM- 17 XF 17 COM+ 17 COM-
TB9A X7
TB9B COM+
TB9C COM-
TB10A X8
TB10B COM+
TB10C COM-
TB11A X9
TB11B COM+
TB11C COM-
TB12A XA
TB12B COM+
TB12C COM-
TB13A XB
TB13B COM+
TB13C COM-
TB14A XC
TB14B COM+
TB14C COM-
TB15A XD
TB15B COM+
TB15C COM-
TB16A XE
TB16B COM+
TB16C COM-
TB17A XF
TB17B COM+
TB17C COM-
1: Attach an unwired connector plug to an unused
one-touch connector for power supply and FG.

Pin layout

Viewed from the front of the module

4 - 26 4 - 26
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection

<When using online connectors>

Online connector
for communication
CONA
1
1 DA
LINK CABLE 2
(IN) 2 DB
3
3 DG
4
4 Empty
5
5 SLD
CONB
1
1 DA
LINK CABLE 2
(OUT) 2 DB
3
3 DG
4
4 Empty
5
5 SLD
One-touch connector
for communication
CONC
UNIT POWER CABLE(IN) 1
1 FG
2
2 +24V(UNIT)
3
3 24G(UNIT)
4
4 Empty
5
5 Empty
COND
1
1 FG
2
UNIT POWER 2 +24V(UNIT)
CABLE(OUT) 3
3 24G(UNIT)
4
4 Empty
5 Empty
5

One-touch connector for power

Online connector
supply and FG *1
for power supply
and FG

1: Attach an unwired connector plug to an unused one-touch connector for power supply and FG.

4 - 27 4 - 27
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

4.2.2 AJ65VBTS3-32D 24VDC input module (positive common (sink type))

Type DC input module

Item AJ65VBTS3-32D Appearance
Number of input points 32 points
Isolation method Photocoupler
Rated input voltage 24VDC
Rated input current Approx. 5mA
Operating voltage range 19.2 to 26.4VDC (ripple ratio: within 5%)
Max. number of simultaneous 100% or 69% (Refer to Section1.3.)
input points
ON voltage/ON current 14VDC or higher/3.5mA or higher
OFF voltage/OFF current 6VDC or lower/1.7mA or lower
Input resistance Approx. 4.7kΩ

NC X10 X11 X12 X13 X14 X15 X16 X17 X18 X19 X1A X1B X1C X1D X1E X1F
Response OFF→ON 1.5ms or less (at 24VDC)
time ON→OFF 1.5ms or less (at 24VDC)
Wiring method for common 16 points/common (3-wire, spring clamp terminal block type)
Input type Positive common (sink type)
Supply current for connected 2.0A or lower/common

COM2-
COM2+
device
Number of occupied stations 32-point assignment/station (32 points used)
Module Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
power supply Current 40mA or lower (at 24VDC and all points ON)
Noise immunity Noise voltage 500Vp-p, noise width 1µs,
noise frequency 25 to 60Hz (DC type noise simulator condition)
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

AJ65VBTS3-32D

COM2+

COM2-
Insulation resistance 10MΩ or higher between all DC external terminals and ground (500VDC insulation

X9 XA XB XC XD XE XF
resistance tester)
Protection degree IP1XB
Weight 0.41kg
External Communication One-touch connector for communication [Transmission circuit]
connection part 5-pin IDC plug is sold separately: A6CON-L5P

COM1+

COM1-
system <Optional>
X8
X7
Online connector for communication: A6CON-LJ5P X6

Power supply One-touch connector for power supply and FG [Module power supply, FG]
X5

part 5-pin IDC plug is sold separately: A6CON-PW5P, A6CON-PW5P-SOD

X4

<Optional>
X3
X2

Online connector for power supply: A6CON-PWJ5P

X1

I/O part 2-piece spring clamp terminal block [I/O power supply, I/O signals]
X0

COM1+

COM1-

Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)

NC

Applicable Connector for Applicable cable:

wire size communication FANC-110SBH, FA-CBL200PSBH, CS-110
D
8 9 A B CD E F
0 1 2 3 4 5 6 7
L ERR.

Connector for 0.66 to 0.98mm2 (AWG18)

C
PW L RUN

power supply and [φ2.2 to 3.0mm (A6CON-PW5P), φ2.0 to 2.3mm (A6CON-PW5P-SOD)]

FG Wire diameter: 0.16mm or more
B
ON

B RATESTATION NO.
1 2 4 1 2 4 8 102040

Insulating coating material: PVC (heat-resistant)

CON A

Spring clamp Stranded wire 0.08 to 1.5mm2 (AWG28 to 16) 1

terminal block for Wire strip length: 8 to 11mm

I/O
Applicable TE0.5 [Applicable wire size: 0.5mm2]
solderless TE0.75 [Applicable wire size: 0.75mm2]
2
terminal TE1 [Applicable wire size: 0.9 to 1.0mm ]
TE1.5 [Applicable wire size: 1.25 to 1.5mm2]
FA-VTC125T9 [Applicable wire size: 0.3 to 1.65mm2]
2
FA-VTCW125T9 [Applicable wire size: 0.3 to 1.65mm ]
Accessory User’s manual, Holding fixtures for screw installation

1: Insert one wire per terminal.

4 - 28 4 - 28
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection
CONA
1
LINK CABLE 2
1 DA Pin number Signal name
2 DB
(IN) 3
4
3 DG 1 DA
4 Empty
5
5 SLD 2 DB
CONB
1
1 DA CON A, B 3 DG
LINK CABLE 2
2 DB
(OUT) 3
4
3 DG 4 Empty
4 Empty
5
5 SLD 5 SLD
One-touch connector for communication
CONC Insulation
1 (FG)
1
UNIT POWER CABLE(IN)
2
1
2
FG
+24V(UNIT)
2 +24V (UNIT)
3
4
3
4
24G(UNIT)
Empty
CON C, D 3 24G (UNIT)
5
5 Empty
4 Empty
COND
1
UNIT POWER CABLE(OUT)
2
1 FG 5 Empty
2 +24V(UNIT)
3
4
3 24G(UNIT) Terminal block
4 Empty
5
1
5 Empty Column A Column B Column C
One-touch connector for power supply and FG
1 Empty 1 COM1+ 1 COM1-
TB1A Empty
TB1B COM1+ 2 X0 2 COM1+ 2 COM1-
TB1C COM1-
Black
TB2A X0 3 X1 3 COM1+ 3 COM1-
Brown
Blue
TB2B
TB2C
COM1+
COM1-
4 X2 4 COM1+ 4 COM1-
3-wire sensor Brown
(sink output)
Detection
circuit
TB3A
TB3B
X1
COM1+
5 X3 5 COM1+ 5 COM1-
Blue
TB3C COM1- 6 X4 6 COM1+ 6 COM1-
TB4A X2
TB4B COM1+ 7 X5 7 COM1+ 7 COM1-
TB4C COM1-
TB5A X3 8 X6 8 COM1+ 8 COM1-
2-wire sensor Detection
(sink output) circuit
TB5B
TB5C
COM1+
COM1-
9 X7 9 COM1+ 9 COM1-
TB6A
TB6B
X4
COM1+
10 X8 10 COM1+ 10 COM1-
TB6C COM1- 11 X9 11 COM1+ 11 COM1-
TB7A X5
TB7B COM1+ 12 XA 12 COM1+ 12 COM1-
TB7C COM1-
TB8A X6 13 XB 13 COM1+ 13 COM1-
TB8B
TB8C
COM1+
COM1-
14 XC 14 COM1+ 14 COM1-
TB9A X7 15 XD 15 COM1+ 15 COM1-
TB9B COM1+
TB9C COM1- 16 XE 16 COM1+ 16 COM1-
TB10A X8
TB10B COM1+ 17 XF 17 COM1+ 17 COM1-
TB10C
TB11A
COM1-
X9 18 Empty 18 COM2+ 18 COM2-
TB11B
TB11C
COM1+
COM1-
19 X10 19 COM2+ 19 COM2-
TB12A XA 20 X11 20 COM2+ 20 COM2-
TB12B COM1+
TB12C COM1- 21 X12 21 COM2+ 21 COM2-
TB13A XB
TB13B COM1+ 22 X13 22 COM2+ 22 COM2-
TB13C
TB14A
COM1-
XC
23 X14 23 COM2+ 23 COM2-
TB14B
TB14C
COM1+
COM1-
24 X15 24 COM2+ 24 COM2-
TB15A XD 25 X16 25 COM2+ 25 COM2-
TB15B COM1+
TB15C COM1- 26 X17 26 COM2+ 26 COM2-
TB16A XE
TB16B COM1+ 27 X18 27 COM2+ 27 COM2-
TB16C
TB17A
COM1-
XF
28 X19 28 COM2+ 28 COM2-
TB17B
TB17C
COM1+
COM1-
29 X1A 29 COM2+ 29 COM2-
TB18A Empty 30 X1B 30 COM2+ 30 COM2-
TB18B COM2+

Black
TB18C COM2- 31 X1C 31 COM2+ 31 COM2-
TB19A X10
Brown
TB19B COM2+ 32 X1D 32 COM2+ 32 COM2-
Blue
3-wire sensor Detection Brown
TB19C
TB20A
COM2-
X11
33 X1E 33 COM2+ 33 COM2-
(sink output) circuit
Blue
TB20B COM2+ 34 X1F 34 COM2+ 34 COM2-
TB20C COM2-
TB21A X12
TB21B COM2+
TB21C COM2-
TB22A X13
2-wire sensor Detection TB22B COM2+
(sink output) circuit TB22C COM2-
TB23A X14
TB23B COM2+
TB23C COM2-
TB24A X15
TB24B COM2+
TB24C COM2-
TB25A X16
TB25B COM2+
TB25C COM2-
TB26A X17
TB26B COM2+
TB26C COM2-
TB27A X18
TB27B COM2+
TB27C COM2-
TB28A X19
TB28B COM2+
TB28C COM2-
TB29A X1A
TB29B COM2+
TB29C COM2-
TB30A X1B
TB30B COM2+
TB30C COM2-
TB31A X1C
TB31B COM2+
TB31C COM2-
TB32A X1D
TB32B COM2+
TB32C COM2-
TB33A X1E
TB33B COM2+
TB33C COM2-
TB34A X1F
TB34B COM2+
TB34C COM2-

1: Attach an unwired connector plug to an unused one-touch connector for power supply and FG.

4 - 29 4 - 29
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection

<When using online connectors>

Online connector
for communication
CONA
1
1 DA
LINK CABLE 2
(IN) 2 DB
3
3 DG
4
4 Empty
5
5 SLD
CONB
1
1 DA
LINK CABLE 2
(OUT) 2 DB
3
3 DG
4
4 Empty
5
5 SLD
One-touch connector
for communication
CONC
UNIT POWER CABLE(IN) 1
1 FG
2
2 +24V(UNIT)
3
3 24G(UNIT)
4
4 Empty
5
5 Empty
COND
1
1 FG
2
UNIT POWER 2 +24V(UNIT)
CABLE(OUT) 3
3 24G(UNIT)
4
4 Empty
5 Empty
5

One-touch connector for power

Online connector
supply and FG *1
for power supply
and FG

1: Attach an unwired connector plug to an unused one-touch connector for power supply and FG.

Pin layout

Viewed from the front of the module

4 - 30 4 - 30
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

4.3 Sensor Connector (e-CON) Type Input Module

4.3.1 AJ65VBTCE3-8D 24VDC input module (positive common (sink type))

Type DC input module

Item AJ65VBTCE3-8D Appearance
Number of input points 8 points
Isolation method Photocoupler
Rated input voltage 24VDC
Rated input current Approx. 5mA
Operating voltage range 19.2 to 26.4VDC (ripple ratio: within 5%)
Max. number of simultaneous 100%
input points
ON voltage/ON current 14VDC or higher/3.5mA or higher
OFF voltage/OFF current 6VDC or lower/1.7mA or lower
Input resistance Approx. 4.7kΩ
Response OFF→ON 1.5ms or less (at 24VDC)
time ON→OFF 1.5ms or less (at 24VDC)
Wiring method for common 8 points/common (3-wire, sensor connector (e-CON) type)
Input type Positive common (sink type)
CON
Supply current for connected 1.0A or lower/common ON
1
device A 2
3
4
5
Number of occupied stations 32-point assignment/station (8 points used) 6
7
8
9
B
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%) 10

40 S
supply Current 30mA or lower (at 24VDC and all points ON) 20
T
A
C 10 T
I
8
Noise immunity Noise voltage 500Vp-p, noise width 1µs, 4
O
N
2
noise frequency 25 to 60Hz (DC type noise simulator condition) 1
N
O.
D 4 B
R
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground 2
1
A
T
E

Insulation resistance 10MΩ or higher between all DC external terminals and ground (500VDC insulation AJ65VBTCE3-8D
PW
resistance tester) X0 L RUN
Protection degree IP1XB L ERR.
X1
Weight 0.10kg 0
1
X2
External Communication One-touch connector for communication [Transmission circuit] 2
3
connection part 5-pin IDC plug is sold separately: A6CON-L5P X3 4
5
system <Optional> 6
X4 7
Online connector for communication: A6CON-LJ5P
X5
Power supply One-touch connector for power supply and FG
part [Module power supply, I/O power supply, FG] X6
5-pin IDC plug is sold separately: A6CON-PW5P, A6CON-PW5P-SOD
X7
<Optional>
Online connector for power supply: A6CON-PWJ5P
I/O part Sensor connector (e-CON) [I/O signals]
1
4-pin IDC plug is sold separately.
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable Connector for Applicable cable:
wire size communication FANC-110SBH, FA-CBL200PSBH, CS-110
Connector for 0.66 to 0.98mm2 (AWG18)
power supply and [φ2.2 to 3.0mm (A6CON-PW5P),
FG φ2.0 to 2.3mm (A6CON-PW5P-SOD)]
Wire diameter: 0.16mm or more
Insulating coating material: PVC (heat-resistant)
Connector for I/O Sensor connector (e-CON).
Applicable connector plugs are sold separately. 1
2
(applicable wire size: 0.08 to 0.5mm , depending on the connector plug)
Accessory User’s manual, Holding fixtures for screw installation

1: Refer to Section 1.6.2 for details.

4 - 31 4 - 31
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection

Pin number Signal name

CONA
1 DA
1
LINK CABLE 2
1 DA 2 DB
2 DB
(IN) 3
3 DG CON A, B 3 DG
4
4 Empty
5
5 SLD
4 Empty
CONB 5 SLD
1
1 DA
LINK CABLE 2
2 DB
1 (FG)
(OUT) 3
4
3 DG 2 +24V (UNIT)
4 Empty
5
5 SLD CON C, D 3 24G (UNIT)
One-touch connector for communication 4 +24V (I/O)
CONC Insulation 5 24G (I/O)
1
UNIT POWER CABLE(IN) 1 FG
2 Signal
3
2 +24V(UNIT)
Pin number Pin layout
4
3 24G(UNIT) name
4 +24V(I/O)
5
5 24G(I/O) 1 +24V
I/O POWER CABLE(IN) COND CON1 2 +V
1
UNIT POWER CABLE(OUT)
2
1 FG
(X0) 3 24G
2 +24V(UNIT)
3
3 24G(UNIT) 4 X0
4
5
4 +24V(I/O)
1 +24V
5 24G(I/O)
I/O POWER CABLE(OUT) CON2 2 +V
One-touch connector for power supply and FG
1
(X1) 3 24G
2 CON1 4 X1
Brown 1
3-wire sensor
2
1 +24V
(sink output)
Detection
Blue 3 CON3 2 +V
Black 4
circuit
(X2) 3 24G
4 X2
CON2
Brown 1
1 +24V
3-wire sensor
(sink output)
2 CON4 2 +V
Blue 3
Detection
Black 4 (X3) 3 24G
circuit
4 X3
CON3 1 +24V
2-wire sensor
1 CON5 2 +V
2
(sink output) Blue 3 (X4) 3 24G
Detection
circuit Brown 4 4 X4
1 +24V
CON6 2 +V
The cable colors are selected according to
IEC 60947-5-2 (JIS C 8201-5-2). (X5) 3 24G
CON8
1 4 X5 Viewed from the
2 1 +24V front of the module
3
4 CON7 2 +V
(X6) 3 24G
4 X6
1 +24V
CON8 2 +V
(X7) 3 24G
4 X7

1: Attach an unwired connector plug to an unused one-touch connector for power supply and FG.
2: Wiring the sensor connector (e-CON) incorrectly may cause malfunction or failure due to short circuit of the power supply.

4 - 32 4 - 32
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection

<When using online connectors>

Online connector
for communication
CONA
1
1 DA
LINK CABLE 2
(IN) 2 DB
3
3 DG
4
4
5
5 SLD
CONB
1
1 DA
LINK CABLE 2
(OUT) 2 DB
3
3 DG
4
4
5
5 SLD
One-touch connector
for communication
CONC
1
UNIT POWER CABLE(IN) 1 FG
2
2 +24V(UNIT)
3
3 24G(UNIT)
4
4 +24V(I/O)
5
5 24G(I/O)
I/O POWER CABLE(IN) COND
1
1 FG
2
UNIT POWER 2 +24V(UNIT)
CABLE(OUT) 3
3 24G(UNIT)
4
I/O POWER 4 +24V(I/O)
CABLE(OUT) 5
5 24G(I/O)

One-touch connector for power

supply and FG *1 Online connector
for power supply
and FG

1: Attach an unwired connector plug to an unused one-touch connector for power supply and FG.

4 - 33 4 - 33
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

4.3.2 AJ65VBTCE3-16D 24VDC input module (positive common (sink type))

Type DC input module

Item AJ65VBTCE3-16D Appearance
Number of input points 16 points
Isolation method Photocoupler
Rated input voltage 24VDC
Rated input current Approx. 5mA
Operating voltage range 19.2 to 26.4VDC (ripple ratio: within 5%)
Max. number of simultaneous 100% or 62.5% (Refer to Section 1.3.)
input points
ON voltage/ON current 14VDC or higher/3.5mA or higher
OFF voltage/OFF current 6VDC or lower/1.7mA or lower
Input resistance Approx. 4.7kΩ
Response OFF→ON 1.5ms or less (at 24VDC)
time ON→OFF 1.5ms or less (at 24VDC)
Wiring method for common 16 points/common (3-wire, sensor connector (e-CON) type)
Input type Positive common (sink type)
Supply current for connected 1.0A or lower/common

F
7
device
Number of occupied stations 32-point assignment/station (16 points used)

AJ65VBTCE3-16D

E
6
Module Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

D
5
power supply Current 35mA or lower (at 24VDC and all points ON)

C
4
Noise immunity Noise voltage 500Vp-p, noise width 1µs,

B
noise frequency 25 to 60Hz (DC type noise simulator condition)

3
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

A
2
Insulation resistance 10MΩ or higher between all DC external terminals and ground (500VDC

9
insulation resistance tester)

8
Protection degree IP1XB

X
Weight 0.10kg
External Communication One-touch connector for communication [Transmission circuit]

D
8 9 A B C D E F
0 1 2 3 4 5 6 7

connection part 5-pin IDC plug is sold separately: A6CON-L5P

PW L RUNL ERR.

system <Optional>

C
Online connector for communication: A6CON-LJ5P
Power supply One-touch connector for power supply and FG

B
ON

B RATE STATION NO.

1 2 4 1 2 4 8102040

part [Module power supply, I/O power supply, FG]

CON A
5-pin IDC plug is sold separately: A6CON-PW5P, A6CON-PW5P-SOD
<Optional>
Online connector for power supply: A6CON-PWJ5P
I/O part Sensor connector (e-CON) [I/O signals]
1
4-pin IDC plug is sold separately.
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable Connector for Applicable cable:
wire size communication FANC-110SBH, FA-CBL200PSBH, CS-110
Connector for 0.66 to 0.98mm2 (AWG18)
power supply [φ2.2 to 3.0mm (A6CON-PW5P), φ2.0 to 2.3mm (A6CON-PW5P-SOD)]
and FG Wire diameter: 0.16mm or more
Insulating coating material: PVC (heat-resistant)
Connector for Sensor connector (e-CON).
1
I/O Applicable connector plugs are sold separately.
(applicable wire size: 0.08 to 0.5mm2, depending on the connector plug)
Accessory User’s manual, Holding fixtures for screw installation

1: Refer to Section 1.6.2 for details.

4 - 34 4 - 34
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection

Pin number Signal name

CONA 1 DA
1
LINK CABLE
2
1
2
DA
DB
2 DB
(IN) 3
4
3 DG CON A, B 3 DG
4 Empty
5
5 SLD 4 Empty
CONB
LINK CABLE
1
1 DA 5 SLD
2
(OUT) 3
2
3
DB
DG
1 (FG)
4
5
4
5
Empty
SLD
2 +24V (UNIT)
One-touch connector for communication CON C, D 3 24G (UNIT)
CONC Insulation
4 +24V (I/O)
1
UNIT POWER CABLE(IN) 1 FG
2
2 +24V(UNIT)
5 24G (I/O)
3
3 24G(UNIT)
4 Pin Signal Pin Signal Pin Signal Pin Signal
4 +24V(I/O)
5
5 24G(I/O) number name number name number name number name
I/O POWER CABLE(IN) COND
UNIT POWER CABLE(OUT)
1
1 FG
1 +24V 1 +24V 1 +24V 1 +24V
2
2 +24V(UNIT) CON CON CON CON
3 2 +V 2 +V 2 +V 2 +V
4
3 24G(UNIT) 1 5 9 13
5
4 +24V(I/O) 3 24G 3 24G 3 24G 3 24G
5 24G(I/O) (X0) (X4) (X8) (XC)
I/O POWER CABLE(OUT) 4 X0 4 X4 4 X8 4 XC
1
One-touch connector for power supply and FG
1 +24V 1 +24V 1 +24V 1 +24V
2 CON1 CON CON CON CON
3-wire sensor
Brown 1 2 +V 2 +V 2 +V 2 +V
2 2 6 10 14
(sink output) Blue 3 24G 3 24G 3 24G 3 24G
3
Detection
Black 4
(X1) (X5) (X9) (XD)
circuit 4 X1 4 X5 4 X9 4 XD
CON2 1 +24V 1 +24V 1 +24V 1 +24V
Brown 1
CON CON CON CON
3-wire sensor 2 +V 2 +V 2 +V 2 +V
(sink output)
2 3 7 11 15
Blue 3 3 24G 3 24G 3 24G 3 24G
Detection
circuit Black 4 (X2) (X6) (XA) (XE)
4 X2 4 X6 4 XA 4 XE
CON3 1 +24V 1 +24V 1 +24V 1 +24V
2-wire sensor
1 CON CON CON CON
2 2 +V 2 +V 2 +V 2 +V
(sink output)
Blue 3
4 8 12 16
Detection Brown 3 24G 3 24G 3 24G 3 24G
circuit 4 (X3) (X7) (XB) (XF)
4 X3 4 X7 4 XB 4 XF

The cable colors are selected according to

IEC 60947-5-2 (JIS C 8201-5-2).

CON16
1
2
3
4

1: Attach an unwired connector plug to an unused one-touch connector for power supply and FG.
2: Wiring the sensor connector (e-CON) incorrectly may cause malfunction or failure due to short circuit of the power supply.

Pin layout

Viewed from the front of the module

4 - 35 4 - 35
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection

<When using online connectors>

1: Attach an unwired connector plug to an unused one-touch connector for power supply and FG.

4 - 36 4 - 36
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

4.3.3 AJ65VBTCE3-32D 24VDC input module (positive common (sink type))

Type DC input module

Specification AJ65VBTCE3-32D Appearance
Number of input points 32 points
Isolation method Photocoupler
Rated input voltage 24VDC
Rated input current Approx. 5mA
Operating voltage range 19.2 to 26.4VDC (ripple ratio: within 5%)
Max. number of simultaneous 100% or 75% (Refer to Section1.3.)
input points
ON voltage/ON current 14VDC or higher/3.5mA or higher
OFF voltage/OFF current 6VDC or lower/1.7mA or lower
Input resistance Approx. 4.7kΩ
Response OFF→ON 1.5ms or less (at 24VDC)
time ON→OFF 1.5ms or less (at 24VDC)

1F
Wiring method for common 32 points/common (3-wire, sensor connector (e-CON) type)

1E
Input type Positive common (sink type)

1D
Supply current for connected 2.0A or lower/common

D
device

1C
C
Number of occupied stations 32-point assignment/station (32 points used)

1B
B
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

1A
A
supply Current 40mA or lower (at 24VDC and all points ON)

19
9
Noise immunity Noise voltage 500Vp-p, noise width 1µs,

18
AJ65VBTCE3-32D

8
noise frequency 25 to 60Hz (DC type noise simulator condition)

17
7
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

16
6
Insulation resistance 10MΩ or higher between all DC external terminals and ground (500VDC insulation

15
5
resistance tester)

14
4
Protection degree IP1XB

13
3
Weight 0.16kg

12
2
External Communication One-touch connector for communication [Transmission circuit]

11
1
connection part 5-pin IDC plug is sold separately: A6CON-L5P

10
0
system <Optional>

X
Online connector for communication: A6CON-LJ5P

D
8 9 A B C D E F
0 1 2 3 4 5 6 7

Power supply part One-touch connector for power supply and FG

PW L RUN L ERR.

[Module power supply, I/O power supply, FG]

C
5-pin IDC plug is sold separately: A6CON-PW5P, A6CON-PW5P-SOD

B
<Optional>
ON

B RATE STATI ON NO.

1 2 4 1 2 4 8 102040

Online connector for power supply: A6CON-PWJ5P CON A

I/O part Sensor connector (e-CON) [I/O signals]

1
4-pin IDC plug is sold separately.
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable Connector for Applicable cable:
wire size communication FANC-110SBH, FA-CBL200PSBH, CS-110
Connector for 0.66 to 0.98mm2 (AWG18)
power supply and [φ2.2 to 3.0mm (A6CON-PW5P), φ2.0 to 2.3mm (A6CON-PW5P-SOD)]
FG Wire diameter: 0.16mm or more
Insulating coating material: PVC (heat-resistant)
1
Connector for I/O Sensor connector (e-CON). Applicable connector plugs are sold separately.
2
(applicable wire size: 0.08 to 0.5mm , depending on the connector plug)
Accessory User’s manual, Holding fixtures for screw installation

1: Refer to Section 1.6.2 for details.

4 - 37 4 - 37
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection

Pin number Signal name

1 DA
2 DB
CON A, B 3 DG
4 Empty
5 SLD
CONA
1
LINK CABLE 2
1 DA 1 (FG)
2 DB
(IN) 3
3 DG 2 +24V (UNIT)
4
4 Empty
5
5 SLD
CON C, D 3 24G (UNIT)
1
CONB 4 +24V (I/O)
1 DA
LINK CABLE
(OUT)
2
3
2 DB 5 24G (I/O)
3 DG
4
4 Empty Pin Signal Pin Signal Pin Signal Pin Signal
5
5 SLD
number name number name number name number name
One-touch connector for communication
1 +24V 1 +24V 1 +24V 1 +24V
CONC Insulation CON CON CON CON
1
1 FG
2 +V 2 +V 2 +V 2 +V
UNIT POWER CABLE(IN) 2 1 9 17 25
2 +24V(UNIT)
3 3 24G 3 24G 3 24G 3 24G
4
3 24G(UNIT) (X0) (X8) (X10) (X18)
5
4 +24V(I/O) 4 X0 4 X8 4 X10 4 X18
5 24G(I/O)
I/O POWER CABLE(IN) COND 1 +24V 1 +24V 1 +24V 1 +24V
UNIT POWER CABLE(OUT)
1
1 FG CON CON CON CON
2 2 +V 2 +V 2 +V 2 +V
3
2 +24V(UNIT) 2 10 18 26
4
3 24G(UNIT) 3 24G 3 24G 3 24G 3 24G
4 +24V(I/O) (X1) (X9) (X11) (X19)
5
5 24G(I/O) 4 X1 4 X9 4 X11 4 X19
I/O POWER CABLE(OUT)
One-touch connector for power supply and FG
1 1 +24V 1 +24V 1 +24V 1 +24V
CON CON CON CON
2 CON1 2 +V 2 +V 2 +V 2 +V
Brown 1
3 11 19 27
3-wire sensor 3 24G 3 24G 3 24G 3 24G
(sink output)
2 (X2) (XA) (X12) (X1A)
Blue 3
Detection
Black
4 X2 4 XA 4 X12 4 X1A
circuit 4
1 +24V 1 +24V 1 +24V 1 +24V
CON CON CON CON
CON2 2 +V 2 +V 2 +V 2 +V
Brown 1 4 12 20 28
3-wire sensor 2 3 24G 3 24G 3 24G 3 24G
(sink output) Blue 3
(X3) (XB) (X13) (X1B)
Detection
Black 4
4 X3 4 XB 4 X13 4 X1B
circuit
1 +24V 1 +24V 1 +24V 1 +24V
CON CON CON CON
CON3 2 +V 2 +V 2 +V 2 +V
1 5 13 21 29
2-wire sensor 2 3 24G 3 24G 3 24G 3 24G
(sink output) Blue 3 (X4) (XC) (X14) (X1C)
Detection
circuit Brown 4 4 X4 4 XC 4 X14 4 X1C
CON 1 +24V 1 +24V 1 +24V 1 +24V
CON CON CON
6 2 +V 2 +V 2 +V 2 +V
The cable colors are selected according 14 22 30
to IEC 60947-5-2 (JIS C 8201-5-2). 3 24G 3 24G 3 24G 3 24G
(XD) (X15) (X1D)
(X5) 4 X5 4 XD 4 X15 4 X1D
CON32
1 1 +24V 1 +24V 1 +24V 1 +24V
2 CON CON CON CON
3 2 +V 2 +V 2 +V 2 +V
4
7 15 23 31
3 24G 3 24G 3 24G 3 24G
(X6) (XE) (X16) (X1E)
4 X6 4 XE 4 X16 4 X1E
1 +24V 1 +24V 1 +24V 1 +24V
CON CON CON CON
2 +V 2 +V 2 +V 2 +V
8 16 24 32
3 24G 3 24G 3 24G 3 24G
(X7) (XF) (X17) (X1F)
4 X7 4 XF 4 X17 4 X1F

1: Attach an unwired connector plug to an unused one-touch connector for power supply and FG.
2: Wiring the sensor connector (e-CON) incorrectly may cause malfunction or failure due to short circuit of the power supply.

4 - 38 4 - 38
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection

<When using online connectors>

Online connector
for communication
CONA
1
1 DA
LINK CABLE 2
(IN) 2 DB
3
3 DG
4
4
5
5 SLD
CONB
1
1 DA
LINK CABLE 2
(OUT) 2 DB
3
3 DG
4
4
5
5 SLD
One-touch connector
for communication
CONC
1
UNIT POWER CABLE(IN) 1 FG
2
2 +24V(UNIT)
3
3 24G(UNIT)
4
4 +24V(I/O)
5
5 24G(I/O)
I/O POWER CABLE(IN) COND
1
1 FG
2
UNIT POWER 2 +24V(UNIT)
CABLE(OUT) 3
3 24G(UNIT)
4
I/O POWER 4 +24V(I/O)
CABLE(OUT) 5
5 24G(I/O)

One-touch connector for power

supply and FG *1 Online connector
for power supply
and FG

1: Attach an unwired connector plug to an unused one-touch connector for power supply and FG.

Pin layout

Viewed from the front of the module

4 - 39 4 - 39
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

4.3.4 AJ65VBTCE3-16DE 24VDC input module (negative common (source type))

Type DC input module

Item AJ65VBTCE3-16DE Appearance
Number of input points 16 points
Isolation method Photocoupler
Rated input voltage 24VDC
Rated input current Approx. 5mA
Operating voltage range 19.2 to 26.4VDC (ripple ratio: within 5%)
Max. number of simultaneous 100% or 62.5% (Refer to Section1.3.)
input points
ON voltage/ON current 14VDC or higher/3.5mA or higher
OFF voltage/OFF current 6VDC or lower/1.7mA or lower
Input resistance Approx. 4.7kΩ
Response OFF→ON 1.5ms or less (at 24VDC)
time ON→OFF 1.5ms or less (at 24VDC)
Wiring method for common 16 points/common (3-wire, sensor connector (e-CON) type)
Input type Negative common (source type)
Supply current for connected 1.0A or lower/common
device
Number of occupied stations 32-point assignment/station (16 points used)
Module Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
power supply Current 35mA or lower (at 24VDC and all points ON)
Noise immunity Noise voltage 500Vp-p, noise width 1µs,
noise frequency 25 to 60Hz (DC type noise simulator condition)
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
Insulation resistance 10MΩ or higher between all DC external terminals and ground (500VDC
insulation resistance tester)
Protection degree IP1XB
Weight 0.11kg
External Communication One-touch connector for communication [Transmission circuit]
connection part 5-pin IDC plug is sold separately: A6CON-L5P
system <Optional>
Online connector for communication: A6CON-LJ5P
Power supply One-touch connector for power supply and FG
part [Module power supply, I/O power supply, FG]
5-pin IDC plug is sold separately: A6CON-PW5P, A6CON-PW5P-SOD
<Optional>
Online connector for power supply: A6CON-PWJ5P
I/O part Sensor connector (e-CON) [I/O signals]
1
4-pin IDC plug is sold separately.
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable Connector for Applicable cable:
wire size communication FANC-110SBH, FA-CBL200PSBH, CS-110
Connector for 0.66 to 0.98mm2 (AWG18)
power supply [φ2.2 to 3.0mm (A6CON-PW5P), φ2.0 to 2.3mm (A6CON-PW5P-SOD)]
and FG Wire diameter: 0.16mm or more
Insulating coating material: PVC (heat-resistant)
Connector for Sensor connector (e-CON).
1
I/O Applicable connector plugs are sold separately.
2
(applicable wire size: 0.08 to 0.5mm , depending on the connector plug)
Accessory User’s manual, Holding fixtures for screw installation

1: Refer to Section 1.6.2 for details.

4 - 40 4 - 40
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection

Pin number Signal name

CONA
1 DA
1
LINK CABLE 2
1 DA 2 DB
2 DB
(IN) 3
4
3 DG CON A, B 3 DG
4 Empty
5
5 SLD 4 Empty
1
CONB
1 DA
5 SLD
LINK CABLE 2
(OUT) 3
2 DB 1 (FG)
3 DG
4
5
4 Empty 2 +24V (UNIT)
5 SLD
One-touch connector for communication CON C, D 3 24G (UNIT)
1
CONC Insulation 4 +24V (I/O)
UNIT POWER CABLE(IN) 1 FG
2
3
2 +24V(UNIT) 5 24G (I/O)
3 24G(UNIT)
4
4 +24V(I/O) Pin Signal Pin Signal Pin Signal Pin Signal
5
5 24G(I/O)
I/O POWER CABLE(IN)
number name number name number name number name
COND
1
UNIT POWER CABLE(OUT)
2
1 FG 1 +24V 1 +24V 1 +24V 1 +24V
2 +24V(UNIT) CON CON CON CON
3
3 24G(UNIT) 2 +V 2 +V 2 +V 2 +V
4
4 +24V(I/O) 1 5 9 13
5
5 24G(I/O) 3 24G 3 24G 3 24G 3 24G
I/O POWER CABLE(OUT)
(X0) (X4) (X8) (XC)
1 4 X0 4 X4 4 X8 4 XC
One-touch connector for power supply and FG
2 CON1 1 +24V 1 +24V 1 +24V 1 +24V
Brown 1
CON CON CON CON
3-wire sensor 2 +V 2 +V 2 +V 2 +V
(source output)
2 2 6 10 14
Blue 3 3 24G 3 24G 3 24G 3 24G
Detection
circuit Black 4 (X1) (X5) (X9) (XD)
4 X1 4 X5 4 X9 4 XD
CON2 1 +24V 1 +24V 1 +24V 1 +24V
Brown 1 CON CON CON CON
3-wire sensor
2 2 +V 2 +V 2 +V 2 +V
(source output) Blue 3 3 7 11 15
Detection
Black 4 3 24G 3 24G 3 24G 3 24G
circuit (X2) (X6) (XA) (XE)
4 X2 4 X6 4 XA 4 XE
CON3 1 +24V 1 +24V 1 +24V 1 +24V
Brown
2-wire sensor
1 CON CON CON CON
(source output)
2 2 +V 2 +V 2 +V 2 +V
Detection
3 4 8 12 16
circuit Blue 4 3 24G 3 24G 3 24G 3 24G
(X3) (X7) (XB) (XF)
4 X3 4 X7 4 XB 4 XF

The cable colors are selected CON16

according to IEC 60947-5-2 1
(JIS C 8201-5-2). 2
3
4

1: Attach an unwired connector plug to an unused one-touch connector for power supply and FG.
2: Wiring the sensor connector (e-CON) incorrectly may cause malfunction or failure due to short circuit of the power supply.

Pin layout

Viewed from the front of the module

4 - 41 4 - 41
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection

<When using online connectors>

1: Attach an unwired connector plug to an unused one-touch connector for power supply and FG.

4 - 42 4 - 42
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

4.3.5 AJ65VBTCE3-32DE 24VDC input module (negative common (source type))

Type DC input module

Specification AJ65VBTCE3-32DE Appearance
Number of input points 32 points
Isolation method Photocoupler
Rated input voltage 24VDC
Rated input current Approx. 5mA
Operating voltage range 19.2 to 26.4VDC (ripple ratio: within 5%)
Max. number of simultaneous 100% or 75% (Refer to Secion1.3.)
input points
ON voltage/ON current 14VDC or higher/3.5mA or higher
OFF voltage/OFF current 6VDC or lower/1.7mA or lower
Input resistance Approx. 4.7kΩ
Response OFF→ON 1.5ms or less (at 24VDC)
time ON→OFF 1.5ms or less (at 24VDC)
Wiring method for common 32 points/common (3-wire, sensor connector (e-CON) type)
Input type Negative common (source type)
Supply current for connected 2.0A or lower/common
device
Number of occupied stations 32-point assignment/station (32 points used)
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
supply Current 40mA or lower (at 24VDC and all points ON)
Noise immunity Noise voltage 500Vp-p, noise width 1µs,
noise frequency 25 to 60Hz (DC type noise simulator condition)
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
Insulation resistance 10MΩ or higher between all DC external terminals and ground (500VDC insulation
resistance tester)
Protection degree IP1XB
Weight 0.16kg
External Communication part One-touch connector for communication [Transmission circuit]
connection 5-pin IDC plug is sold separately: A6CON-L5P
system <Optional>
Online connector for communication: A6CON-LJ5P
Power supply part One-touch connector for power supply and FG
[Module power supply, I/O power supply, FG]
5-pin IDC plug is sold separately: A6CON-PW5P, A6CON-PW5P-SOD
<Optional>
Online connector for power supply: A6CON-PWJ5P
I/O part Sensor connector (e-CON) [I/O signals]
1
4-pin IDC plug is sold separately.
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable Connector for Applicable cable:
wire size communication FANC-110SBH, FA-CBL200PSBH, CS-110
Connector for power 0.66 to 0.98mm2 (AWG18)
supply and FG [φ2.2 to 3.0mm (A6CON-PW5P), φ2.0 to 2.3mm (A6CON-PW5P-SOD)]
Wire diameter: 0.16mm or more
Insulating coating material: PVC (heat-resistant)
Connector for I/O Sensor connector (e-CON).
1
Applicable connector plugs are sold separately.
(applicable wire size: 0.08 to 0.5mm2, depending on the connector plug)
Accessory User’s manual, Holding fixtures for screw installation

1: Refer to Section 1.6.2 for details.

4 - 43 4 - 43
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection

Pin number Signal name

1 DA
2 DB
CON A, B 3 DG
4 Empty
5 SLD
1 (FG)
CONA 2 +24V (UNIT)
1
LINK CABLE 2
1
2
DA
DB
CON C, D 3 24G (UNIT)
(IN) 3
4
3
4
DG
Empty
4 +24V (I/O)
5
5 SLD
5 24G (I/O)
CONB
1
LINK CABLE 2
1 DA Pin Signal Pin Signal Pin Signal Pin Signal
2 DB
(OUT) 3
3 DG number name number name number name number name
4
4 Empty
5
5 SLD 1 +24V 1 +24V 1 +24V 1 +24V
One-touch connector for communication CON CON CON CON
2 +V 2 +V 2 +V 2 +V
CONC Insulation 1 9 17 25
UNIT POWER CABLE(IN) 1
1 FG 3 24G 3 24G 3 24G 3 24G
2
2 +24V(UNIT)
(X0) (X8) (X10) (X18)
3
3 24G(UNIT) 4 X0 4 X8 4 X10 4 X18
4
4 +24V(I/O)
5
5 24G(I/O)
1 +24V 1 +24V 1 +24V 1 +24V
I/O POWER CABLE(IN) CON CON CON CON
1
COND 2 +V 2 +V 2 +V 2 +V
UNIT POWER CABLE(OUT)
2
1 FG 2 10 18 26
2 +24V(UNIT) 3 24G 3 24G 3 24G 3 24G
3
3 24G(UNIT) (X1) (X9) (X11) (X19)
4
5
4 +24V(I/O) 4 X1 4 X9 4 X11 4 X19
5 24G(I/O)
I/O POWER CABLE(OUT) 1 +24V 1 +24V 1 +24V 1 +24V
1
CON CON CON CON
One-touch connector for power supply and FG 2 +V 2 +V 2 +V 2 +V
2 CON1 3 11 19 27
Brown 1 3 24G 3 24G 3 24G 3 24G
3-wire sensor
2
(X2) (XA) (X12) (X1A)
(source output)
Blue 3 4 X2 4 XA 4 X12 4 X1A
Detection
circuit Black 4
1 +24V 1 +24V 1 +24V 1 +24V
CON CON CON CON
CON2 2 +V 2 +V 2 +V 2 +V
Brown 1
4 12 20 28
3-wire sensor 3 24G 3 24G 3 24G 3 24G
(source output) 2 (X3) (XB) (X13) (X1B)
Blue
Detection
3
4 X3 4 XB 4 X13 4 X1B
circuit Black 4
1 +24V 1 +24V 1 +24V 1 +24V
CON CON CON CON
CON3 2 +V 2 +V 2 +V 2 +V
2-wire sensor
Brown 1 5 13 21 29
2 3 24G 3 24G 3 24G 3 24G
(source output)
Detection 3 (X4) (XC) (X14) (X1C)
circuit Blue 4 4 X4 4 XC 4 X14 4 X1C
1 +24V 1 +24V 1 +24V 1 +24V
CON CON CON CON
The cable colors are selected according to 2 +V 2 +V 2 +V 2 +V
IEC 60947-5-2 (JIS C 8201-5-2). 6 14 22 30
CON32
3 24G 3 24G 3 24G 3 24G
1 (X5) (XD) (X15) (X1D)
2 4 X5 4 XD 4 X15 4 X1D
3
4 1 +24V 1 +24V 1 +24V 1 +24V
CON CON CON CON
2 +V 2 +V 2 +V 2 +V
7 15 23 31
3 24G 3 24G 3 24G 3 24G
(X6) (XE) (X16) (X1E)
4 X6 4 XE 4 X16 4 X1E
1 +24V 1 +24V 1 +24V 1 +24V
CON CON CON CON
2 +V 2 +V 2 +V 2 +V
8 16 24 32
3 24G 3 24G 3 24G 3 24G
(X7) (XF) (X17) (X1F)
4 X7 4 XF 4 X17 4 X1F

1: Attach an unwired connector plug to an unused one-touch connector for power supply and FG.
2: Wiring the sensor connector (e-CON) incorrectly may cause malfunction or failure due to short circuit of the power supply.

4 - 44 4 - 44
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection

<When using online connectors>

1: Attach an unwired connector plug to an unused one-touch connector for power supply and FG.

Pin layout

Viewed from the front of the module

4 - 45 4 - 45
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

4.4 One-Touch Connector Type Input Module

4.4.1 AJ65VBTCU3-8D1 24VDC input module (positive common (sink type))

Type DC input module

Item AJ65VBTCU3-8D1 Appearance
Number of input points 8 points
Isolation method Photocoupler
Rated input voltage 24VDC
Rated input current Approx. 5mA
Operating voltage range 19.2 to 26.4VDC (ripple ratio: within 5%)
Max. number of simultaneous 100%
input points
ON voltage/ON current 15VDC or higher/3mA or higher
OFF voltage/OFF current 3VDC or lower/0.5mA or lower
Input resistance Approx. 4.7kΩ
Response time OFF→ON 0.2ms or less (at 24VDC)
ON→OFF 0.2ms or less (at 24VDC)
AJ65VBTCU3-8D1
Wiring method for common 8 points/common (3-wire, one-touch connector type) CON
Input type Positive common (sink type) A

Supply current for connected 1.0A or lower/common

CON
device B
Number of occupied stations 32-point assignment/station (8 points used)
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%) X0 PW

supply Current 35mA or lower (at 24VDC and all points ON) L RUN
X1
Noise immunity Noise voltage 500Vp-p, noise width 1µs, L ERR

noise frequency 25 to 60Hz (DC type noise simulator condition) X2

0
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground 1
X3 2
Insulation resistance 10MΩ or higher between all DC external terminals and ground (500VDC insulation 3
4
resistance tester) 5
X4
6
Protection degree IP1XB 7
Weight 0.15kg X5
External Communication part One-touch connector for communication [Transmission circuit]
connection 5-pin IDC plug is sold separately. X6

system <Optional>
X7
Online connector for communication: A6CON-LJ5P
Power supply part One-touch connector for power supply and FG
[Module power supply, I/O power supply, FG] CON
5-pin IDC plug is sold separately: A6CON-PW5P, A6CON-PW5P-SOD C
<Optional>
Online connector for power supply: A6CON-PWJ5P CON
D
I/O part One-touch connector for I/O
4-pin IDC plug is sold separately.
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable Connector for Applicable cable:
wire size communication FANC-110SBH, FA-CBL200PSBH, CS-110
Connector for power 0.66 to 0.98mm2 (AWG18)
supply and FG [φ2.2 to 3.0mm (A6CON-PW5P), φ2.0 to 2.3mm (A6CON-PW5P-SOD)]
Wire diameter: 0.16mm or more
Insulating coating material: PVC (heat-resistant)
Connector for φ1.0 to 1.4 (A6CON-P214), φ1.4 to 2.0 (A6CON-P220)
I/O [Applicable wire size: 0.14 to 0.2mm2]
φ1.0 to 1.4 (A6CON-P514), φ1.4 to 2.0 (A6CON-P520)
[Applicable wire size: 0.3 to 0.5mm2]
Accessory User’s manual

4 - 46 4 - 46
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection

Pin Signal
Pin layout
number name
1 DA
2 DB
CON
3 DG
CONA A, B
1
1 DA
4 Empty
LINK CABLE 2
(IN) 3
2 DB 5 SLD
3 DG
4
4 Empty 1 X0
5
5 SLD 2 +V
CONB CON1
1
1 DA 3 +24V
LINK CABLE 2
(OUT) 3
2 DB 4 24G
3 DG
4 1 X1
4 Empty
5
5 SLD
2 +V
One-touch connector for communication 5 4 3 2 1
CON2
3 +24V
CONC Insulation 4 24G
1 CONA
UNIT POWER CABLE(IN) 1 FG
2 1 X2
2 +24V(UNIT)
3 CONB
3 24G(UNIT)
4 2 +V
5
4 +24V(I/O) CON3
5 24G(I/O) 43 2 1 3 +24V
I/O POWER CABLE(IN) COND
1 CON1 4 24G
UNIT POWER CABLE(OUT) 1 FG
2
2 +24V(UNIT) 1 X3
3
3 24G(UNIT) CON2
4
4 +24V(I/O)
2 +V
5 CON4
5 24G(I/O) CON3 3 +24V
I/O POWER CABLE(OUT)
1 CON4 4 24G
One-touch connector for power supply and FG
1 X4
CON1 CON5
Black
2 +V
3-wire sensor 1 CON5
(sink output)
Brown 2 CON6 3 +24V
3
Detection Blue 4 4 24G
circuit CON7
1 X5
CON2 CON8 2 +V
Brown 1
CON6
2-wire sensor 3 +24V
(sink output) 2 5 4 3 2 1
Detection 3 4 24G
circuit Blue 4
CONC 1 X6
COND 2 +V
CON7
3 +24V
Viewed from the 4 24G
CON8
front of the module
1 1 X7
2
3 2 +V
CON8
4 3 +24V
4 24G
1 (FG)
2 +24V
(UNIT)
CON 3 24G
C, D (UNIT)
4 +24V
(I/O)
1: Attach an unwired connector plug to an unused one-touch connector for power supply and FG. 5 24G (I/O)

4 - 47 4 - 47
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection

<When using online connectors>

Online connector
for communication
CONA
1
1 DA
LINK CABLE 2
(IN) 2 DB
3
3 DG
4
4
5
5 SLD
CONB
1
1 DA
LINK CABLE 2
(OUT) 2 DB
3
3 DG
4
4
5
5 SLD
One-touch connector
for communication
CONC
1
UNIT POWER CABLE(IN) 1 FG
2
2 +24V(UNIT)
3
3 24G(UNIT)
4
4 +24V(I/O)
5
5 24G(I/O)
I/O POWER CABLE(IN) COND
1
1 FG
2
UNIT POWER 2 +24V(UNIT)
CABLE(OUT) 3
3 24G(UNIT)
4
I/O POWER 4 +24V(I/O)
CABLE(OUT) 5
5 24G(I/O)

One-touch connector for power

supply and FG *1 Online connector
for power supply
and FG

1: Attach an unwired connector plug to an unused one-touch connector for power supply and FG.

4 - 48 4 - 48
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

4.4.2 AJ65SBTC4-16D 24VDC input module (positive common (sink), negative common
(source) loading)

Type DC input module

Item AJ65SBTC4-16D Appearance
Number of input points 16 points
Isolation method Photocoupler
Rated input voltage 24VDC
Rated input current Approx. 5mA
Operating voltage range 19.2 to 26.4VDC (ripple ratio: within 5%)
Max. number of simultaneous input points 100%
ON voltage/ON current 14VDC or higher/3.5mA or higher
OFF voltage/OFF current 6VDC or lower/1.7mA or lower
Input resistance Approx. 4.7kΩ
Response time OFF→ON 1.5ms or less (at 24VDC)
ON→OFF 1.5ms or less (at 24VDC)
Wiring method for common 16 points/common (4-wire, one-touch connector type)
Input type Positive/negative common shared type (sink/source shared type)
(Selected using the switch.)
Number of occupied stations 32-point assignment/station (16 points used)

COM-
CTL+
Module power supply Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

40 20 10 8 4 2 1 4 2 1
B RATE
Current 35mA or lower (at 24VDC and all points ON)

+24V
24G
XF
X7
STATION NO.
Noise immunity Noise voltage 500Vp-p, noise width 1µs,

+24V
24G
XE
X6
noise frequency 25 to 60Hz (DC type noise simulator condition)

+24V
24G
XD
X5
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

ON
Insulation resistance 10MΩ or higher between all DC external terminals and ground (500VDC

+24V
24G
XC
X4
insulation resistance tester)

+24V
24G
X8 9 A B C D E F

XB
X3
Protection degree IP2X

+24V
24G
XA
X2
Weight 0.15kg

AJ65SBTC4-16D

+24V
24G
X1
X9
External Communication part, 7-point two-piece terminal block
connection module power supply part [Transmission circuit, module power supply, FG]

+24V
24G
X0
X8
system M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m) X0 1 2 3 4 5 6 7

(FG)
24G
Applicable solderless terminal: 2 or less
I/O power supply part 2-point direct-mount terminal block
+24V

SLD
[I/O power supply]
DG

M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)

DB
DA

Applicable solderless terminal: 2 or less

I/O part Dedicated one-touch connector [I/O signals]
4-pin IDC plug is sold separately.
Module mounting screw M4 screw with plain washer finished round
(tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable Communication part, Applicable y RAV1.25-3 (compliant with JIS C 2805)
wire size module power supply solderless [Applicable wire size: 0.3 to 1.25mm2]
part terminal y V2-MS3, RAP2-3SL, TGV2-3N
I/O power supply part [Applicable wire size: 1.25 to 2.0mm2]
φ1.0 to 1.4 (A6CON-P214), φ1.4 to 2.0 (A6CON-P220)
[Applicable wire size: 0.14 to 0.2mm2]
I/O part
φ1.0 to 1.4 (A6CON-P514), φ1.4 to 2.0 (A6CON-P520)
[Applicable wire size: 0.3 to 0.5mm2]
Accessory User’s manual

4 - 49 4 - 49
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection (positive common (sink input))

1 DA
2 DB
3 DG Insulation
4 SLD
5 +24V
6 FG
7 24G
Module power supply

4-wire sensor
CON1
(sink output) Black 1
Detection
circuit White 2
Brown 3
Blue 4

3-wire sensor
CON2
(sink output)
Black 1
Detection
circuit 2
Brown 3
Blue 4

2-wire sensor CON8

(sink output) Brown 1
Detection 2
circuit 3
Blue 4

The cable colors are selected according to

IEC 60947-5-2 (JIS C 8201-5-2).

Sink/source switch
Source type Sink type
8 CTL+
9 COM-

Terminal
Pin layout Signal name Pin number Signal name
number
TB1 DA 1 X4
TB2 DB 2 XC
CON5
TB3 DG 3 +24V
TB4 SLD 4 24G
TB5 +24V 1 X5
TB6 (FG) 2 XD
CON6
TB7 24G 3 +24V
4 24G
Pin number Signal name
1 X6
1 X0 2 XE
CON7
2 X8 3 +24V
CON1
3 +24V 4 24G
4 24G 1 X7
1 X1 2 XF
CON8
Viewed from the front of the module 2 X9 3 +24V
CON2
3 +24V 4 24G
4 24G Terminal
Signal name
1 X2 number
2 XA TB8 CTL+
CON3
3 +24V TB9 COM-
4 24G
1 X3
2 XB
CON4
3 +24
4 24G

4 - 50 4 - 50
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection (negative common (source input))

1 DA
2 DB
3 DG Insulation
4 SLD
5 +24V
6 FG
7 24G
Module power supply

4-wire sensor CON1

(source output) Black 1
Detection
circuit White 2
Brown 3
Blue 4

3-wire sensor CON2

(source output) Black 1
Detection 2
circuit
Brown 3
Blue 4

2-wire sensor CON8

(source output) Brown 1
Detection 2
circuit Blue 3
4

The cable colors are selected according to

IEC 60947-5-2 (JIS C 8201-5-2).
Sink/source switch

Source type Sink type

8 CTL+
9 COM-

Terminal
Pin layout Signal name Pin number Signal name
number
TB1 DA 1 X4
TB2 DB 2 XC
CON5
TB3 DG 3 +24V
TB4 SLD 4 24G
TB5 +24V 1 X5
TB6 (FG) 2 XD
CON6
TB7 24G 3 +24V
4 24G
Pin number Signal name
1 X6
1 X0 2 XE
CON7
2 X8 3 +24V
CON1
3 +24V 4 24G
4 24G 1 X7
1 X1 2 XF
CON8
Viewed from the front of the module 2 X9 3 +24V
CON2
3 +24V 4 24G
4 24G Terminal
Signal name
1 X2 number
2 XA TB8 CTL+
CON3
3 +24V TB9 COM-
4 24G
1 X3
2 XB
CON4
3 +24
4 24G

4 - 51 4 - 51
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

4.4.3 AJ65SBTC4-16DN 24VDC input module (positive common (sink type))

Type DC input module

Specification AJ65SBTC4-16DN Appearance
Number of input points 16 points
Isolation method Photocoupler
Rated input voltage 24VDC
Rated input current Approx. 5mA
Operating voltage range 19.2 to 26.4VDC (ripple ratio: within 5%)
Max. number of simultaneous input points 100%
ON voltage/ON current 14VDC or higher/3.5mA or higher
OFF voltage/OFF current 6VDC or lower/1.7mA or lower
Input resistance Approx. 4.7kΩ
Response time OFF→ON 1.5ms or less (at 24VDC)
ON→OFF 1.5ms or less (at 24VDC)
Wiring method for common 16 points/common (4-wire, one-touch connector type)
Input type Positive common (sink type)
Supply current for connected device 1.0A or lower/common

ON
Number of occupied stations 32-point assignment/station (16 points used)

COM-
COM+
40 20 10 8 4 2 1 4 2 1
Module power supply Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

B RATE
Current 35mA or lower (at 24VDC and all points ON)

+24V
24G
XF
X7
STATION NO.
Noise immunity Noise voltage 500Vp-p, noise width 1µs,

+24V
24G
XE
X6
noise frequency 25 to 60Hz (DC type noise simulator condition)

+24V
24G
XD
X5
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

+24V
24G
Insulation resistance 10MΩ or higher between all DC external terminals and ground (500VDC

XC
X4
insulation resistance tester)

+24V
24G
XB
X3
X8 9 A B C D E F
Protection degree IP2X

+24V
24G
XA
X2
Weight 0.15kg

AJ65SBTC4-16DN

+24V
24G
X1
X9
External Communication part, 7-point two-piece terminal block

+24V
24G
connection module power supply part [Transmission circuit, module power supply, FG]

X0
X8
PW L RUN L ERR. X0 1 2 3 4 5 6 7
system M3×5.2 screw (tightening torque range:0.59 to 0.88N•m)

(FG)
24G
Applicable solderless terminal: 2 or less
I/O power supply part 2-point direct-mount terminal block

+24V

SLD
[I/O power supply]
M3×5.2 screw (tightening torque range:0.59 to 0.88N•m) DG
DB
DA

Applicable solderless terminal: 2 or less

I/O part Dedicated one-touch connector [I/O signals]
4-pin IDC plug is sold separately.
Module mounting screw M4 screw with plain washer finished round
(tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable Communication part, Applicable y RAV1.25-3 (compliant with JIS C 2805)
wire size module power supply part solderless [Applicable wire size: 0.3 to 1.25mm2]
I/O power supply part terminal y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
I/O part φ1.0 to 1.4 (A6CON-P214), φ1.4 to 2.0 (A6CON-P220)
[Applicable wire size: 0.14 to 0.2mm2]
φ1.0 to 1.4 (A6CON-P514), φ1.4 to 2.0 (A6CON-P520)
[Applicable wire size: 0.3 to 0.5mm2]
Accessory User’s manual

4 - 52 4 - 52
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection
Terminal Signal
number name
TB1 DA
TB2 DB
TB3 DG
TB4 SLD
TB5 +24V
TB6 (FG)
1 DA TB7 24G
2 DB
3 DG
Pin Signal
Insulation
4 SLD number name
5 +24V 1 X0
6 FG
7 24G
2 X8
Module power supply CON1
3 +24V
4 24G
4-wire sensor
CON1 1 X1
(sink output)
Black 1
Detection 2 X9
circuit White 2 CON2
Brown 3 3 +24V
Blue 4 4 24G
1 X2
3-wire sensor
CON2 2 XA
(sink output) CON3
Black 1 3 +24V
Detection
circuit 2
Brown 3 4 24G
Blue 4 1 X3
2 XB
CON4
3 +24
4 24G
1 X4
2-wire sensor CON8 2 XC
(sink output) Brown 1
CON5
3 +24V
Detection 2
circuit
3 4 24G
Blue 4 1 X5
2 XD
The cable colors are selected according to CON6
3 +24V
IEC 60947-5-2 (JIS C 8201-5-2).
4 24G
1 X6
2 XE
CON7
3 +24V
8 COM+
9 COM- 4 24G
1 X7
2 XF
CON8
3 +24V
4 24G
Terminal Signal
number name
TB8 COM+
TB9 COM-
Pin layout

Viewed from the front of the module

4 - 53 4 - 53
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

4.4.4 AJ65SBTC4-16DE 24VDC input module (negative common (source type))

Type DC input module

Specification AJ65SBTC4-16DE Appearance
Number of input points 16 points
Isolation method Photocoupler
Rated input voltage 24VDC
Rated input current Approx. 5mA
Operating voltage range 19.2 to 26.4VDC (ripple ratio: within 5%)
Max. number of simultaneous input points 100%
ON voltage/ON current 14VDC or higher/3.5mA or higher
OFF voltage/OFF current 6VDC or lower/1.7mA or lower
Input resistance Approx. 4.7kΩ
Response time OFF→ON 1.5ms or less (at 24VDC)
ON→OFF 1.5ms or less (at 24VDC)
Wiring method for common 16 points/common (4-wire, one-touch connector type)
Input type Negative common (source type)
Supply current for connected device 1.0A or lower/common

ON
Number of occupied stations 32-point assignment/station (16 points used)

COM-
COM+
40 20 10 8 4 2 1 4 2 1
Module power supply Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

B RATE
Current 35mA or lower (at 24VDC and all points ON)

+24V
24G
XF
X7
STATION NO.
Noise immunity Noise voltage 500Vp-p, noise width 1µs,

+24V
24G
XE
X6
noise frequency 25 to 60Hz (DC type noise simulator condition)

+24V
24G
XD
X5
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

+24V
24G
Insulation resistance 10MΩ or higher between all DC external terminals and ground (500VDC

XC
X4
insulation resistance tester)

+24V
24G
XB
X3
X8 9 A B C D E F
Protection degree IP2X

+24V
24G
XA
X2
Weight 0.15kg

AJ65SBTC4-16DE

+24V
24G
X1
X9
External Communication part, 7-point two-piece terminal block

+24V
24G
connection module power supply part [Transmission circuit, module power supply, FG]

X0
X8
PW L RUN L ERR. X0 1 2 3 4 5 6 7
system M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)

(FG)
24G
Applicable solderless terminal: 2 or less
I/O power supply part 2-point direct-mount terminal block

+24V

SLD
[I/O power supply]
M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m) DG

DB
DA

Applicable solderless terminal: 2 or less

I/O part Dedicated one-touch connector [I/O signals]
4-pin IDC plug is sold separately.
Module mounting screw M4 screw with plain washer finished round
(tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable Communication part, Applicable y RAV1.25-3 (compliant with JIS C 2805)
2
wire size module power supply part solderless [Applicable wire size: 0.3 to 1.25mm ]
I/O power supply part terminal y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
I/O part φ1.0 to 1.4 (A6CON-P214), φ1.4 to 2.0 (A6CON-P220)
[Applicable wire size: 0.14 to 0.2mm2]
φ1.0 to 1.4 (A6CON-P514), φ1.4 to 2.0 (A6CON-P520)
[Applicable wire size: 0.3 to 0.5mm2]
Accessory User’s manual

4 - 54 4 - 54
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection
Terminal Signal
number name
TB1 DA
TB2 DB
TB3 DG
TB4 SLD
TB5 +24V
TB6 (FG)
TB7 24G
1 DA
2 DB Signal
Pin number
3 DG Insulation name
4 SLD
5 +24V
1 X0
6 FG 2 X8
7 24G
CON1
Module power supply 3 +24V
4 24G
4-wire sensor 1 X1
CON1
(source output)
Black 1 2 X9
Detection
White 2
CON2
circuit 3 +24V
Brown 3
Blue 4 4 24G
1 X2
3-wire sensor CON2 2 XA
(source output) CON3
Black 1 3 +24V
Detection 2
circuit
Brown
4 24G
3
Blue 4 1 X3
2 XB
CON4
3 +24
4 24G
1 X4
2-wire sensor CON8 2 XC
(source output) Brown 1 CON5
Detection 3 +24V
2
circuit Blue 4 24G
3
4 1 X5
2 XD
CON6
The cable colors are selected according to 3 +24V
IEC 60947-5-2 (JIS C 8201-5-2). 4 24G
1 X6
2 XE
CON7
8 COM+ 3 +24V
9 COM-
4 24G
1 X7
2 XF
CON8
3 +24V
4 24G
Terminal Signal
number name
TB8 COM+
TB9 COM-
Pin layout

Viewed from the front of the module

4 - 55 4 - 55
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

4.4.5 AJ65VBTCU3-16D1 24VDC input module (positive common (sink type))

Type DC input module

Item AJ65VBTCU3-16D1 Appearance
Number of input points 16 points
Isolation method Photocoupler
Rated input voltage 24VDC
Rated input current Approx. 5mA
Operating voltage range 19.2 to 26.4VDC (ripple ratio: within 5%)
Max. number of simultaneous 100%
input points
ON voltage/ON current 15VDC or higher/3mA or higher
OFF voltage/OFF current 3VDC or lower/0.5mA or lower
Input resistance Approx. 4.7kΩ
Response time OFF→ON 0.2ms or less (at 24VDC)
ON→OFF 0.2ms or less (at 24VDC)
Wiring method for common 16 points/common (3-wire, one-touch connector type)
AJ65VBTCU3-16D1
Input type Positive common (sink type)
CON
Supply current for connected 1.0A or lower/common A

device
CON
Number of occupied stations 32-point assignment/station (16 points used) B

Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

PW
supply Current 40mA or lower (at 24VDC and all points ON)
L RUN
Noise immunity Noise voltage 500Vp-p, noise width 1µs, L ERR
noise frequency 25 to 60Hz (DC type noise simulator condition)
0
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground 1
2
Insulation resistance 10MΩ or higher between all DC external terminals and ground (500VDC 3
4
insulation resistance tester) 5
6
Protection degree IP1XB 7
Weight 0.19kg
8
External Communication One-touch connector for communication [Transmission circuit] 9
A
connection part 5-pin IDC plug is sold separately. B
C
system <Optional> D
E
Online connector for communication: A6CON-LJ5P X0 X7 X8 XF F
Power supply One-touch connector for power supply and FG
CON
part [Module power supply, I/O power supply, FG] C

5-pin IDC plug is sold separately: A6CON-PW5P, A6CON-PW5P-SOD

CON
<Optional> D
Online connector for power supply: A6CON-PWJ5P
I/O part One-touch connector for I/O
4-pin IDC plug is sold separately.
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable Connector for Applicable cable:
wire size communication FANC-110SBH, FA-CBL200PSBH, CS-110
Connector for 0.66 to 0.98mm2 (AWG18)
power supply [φ2.2 to 3.0mm (A6CON-PW5P), φ2.0 to 2.3mm (A6CON-PW5P-SOD)]
and FG Wire diameter: 0.16mm or more
Insulating coating material: PVC (heat-resistant)
Connector for φ1.0 to 1.4 (A6CON-P214), φ1.4 to 2.0 (A6CON-P220)
I/O [Applicable wire size: 0.14 to 0.2mm2]
φ1.0 to 1.4 (A6CON-P514), φ1.4 to 2.0 (A6CON-P520)
[Applicable wire size: 0.3 to 0.5mm2]
Accessory User’s manual

4 - 56 4 - 56
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection

Pin
Pin layout Signal name
number
1 DA
2 DB
CON
3 DG
A, B
4 Empty
5 SLD
1 X0
CON 2 +V
1 3 +24V
4 24G
1 X1
CON 2 +V
CONA 2
1 3 +24V
1 DA
LINK CABLE 2
2 DB 4 24G
(IN) 3
4
3 DG 1 X2
4 Empty
5
5
CON 2 +V
SLD
3 3 +24V
CONB
1
1 DA 4 24G
LINK CABLE 2
(OUT) 3
2 DB 1 X3
3 DG
4
4 Empty
CON 2 +V
5
5 SLD 4 3 +24V
One-touch connector for communication 4 24G
1 X4
CONC Insulation
UNIT POWER CABLE(IN) 1
1 FG CON 2 +V
2 5
3
2 +24V(UNIT) 3 +24V
24G(UNIT)
4
3 4 24G
4 +24V(I/O)
5
5 24G(I/O) 5 4 3 2 1 1 X5
I/O POWER CABLE(IN) COND CON 2 +V
1 CONA
UNIT POWER CABLE(OUT)
2
1 FG 6 3 +24V
3
2 +24V(UNIT) CONB 4 24G
3 24G(UNIT)
4
4 +24V(I/O) 4321 4321 1 X6
5
5 24G(I/O) CON 2 +V
I/O POWER CABLE(OUT) CON1 CON9
7 3 +24V
1
One-touch connector for power supply and FG CON2 CON10 4 24G
CON1 1 X7
CON3 CON11
3-wire sensor
Black 1 CON 2 +V
Brown 2 8
(sink output) 3
CON4 CON12 3 +24V
Detection Blue 4 4 24G
circuit CON5 CON13
1 X8
CON2
CON6 CON14 CON 2 +V
2-wire sensor Brown 1 9 3 +24V
CON7 CON15
(sink output) 2 4 24G
Detection 3
circuit Blue 4
CON8 CON16 1 X9
CON 2 +V
5 4 3 2 1 10 3 +24V
CONC 4 24G
COND 1 XA
CON16
CON 2 +V
1
2 11 3 +24V
Viewed from the front of the module
3 4 24G
4
1 XB
CON 2 +V
12 3 +24V
4 24G
1 XC
CON 2 +V
13 3 +24V
4 24G
1 XD
CON 2 +V
14 3 +24V
4 24G
1 XE
CON 2 +V
15 3 +24V
4 24G
1 XF
CON 2 +V
16 3 +24V
4 24G
1 (FG)
2 +24V (UNIT)
CON
1: Attach an unwired connector plug to an unused one-touch connector for power supply 3 24G (UNIT)
C, D
and FG. 4 +24V (I/O)
5 24G (I/O)

4 - 57 4 - 57
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection

<When using online connectors>

Online connector
for communication
CONA
1
1 DA
LINK CABLE 2
(IN) 2 DB
3
3 DG
4
4
5
5 SLD
CONB
1
1 DA
LINK CABLE 2
(OUT) 2 DB
3
3 DG
4
4
5
5 SLD
One-touch connector
for communication
CONC
1
UNIT POWER CABLE(IN) 1 FG
2
2 +24V(UNIT)
3
3 24G(UNIT)
4
4 +24V(I/O)
5
5 24G(I/O)
I/O POWER CABLE(IN) COND
1
1 FG
2
UNIT POWER 2 +24V(UNIT)
CABLE(OUT) 3
3 24G(UNIT)
4
I/O POWER 4 +24V(I/O)
CABLE(OUT) 5
5 24G(I/O)

One-touch connector for power

supply and FG *1 Online connector
for power supply
and FG

1: Attach an unwired connector plug to an unused one-touch connector for power supply and FG.

4 - 58 4 - 58
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

4.4.6 AJ65SBTC1-32D 24VDC input module (positive common (sink), negative common
(source) loading)

Type DC input module

Item AJ65SBTC1-32D Appearance
Number of input points 32 points
Isolation method Photocoupler
Rated input voltage 24VDC
Rated input current Approx. 5mA
Operating voltage range 19.2 to 26.4VDC (ripple ratio: within 5%)
Max. number of simultaneous input points 80%
ON voltage/ON current 14VDC or higher/3.5mA or higher
OFF voltage/OFF current 6VDC or lower/1.7mA or lower
Input resistance Approx. 4.7kΩ
Response time OFF→ON 1.5ms or less (at 24VDC)
ON→OFF 1.5ms or less (at 24VDC)
Wiring method for common 32 points/common (2 points) (1-wire, one-touch connector type)

ON
Input type Positive/negative common shared type (sink/source shared type)

COM
COM
Number of occupied stations 32-point assignment/station (32 points used)

B RATE
40 20 10 8 4 2 1 4 2 1
Module power supply Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

X1C
X1D
X1E
X1F
STATION NO.
Current 45mA or lower (at 24VDC and all points ON)

X1A
X1B
X18
X19
Noise immunity Noise voltage 500Vp-p, noise width 1µs,
noise frequency 25 to 60Hz (DC type noise simulator condition)

X14
X15
X16
X17
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

X10-X1F
X0-XF

X10
X11
X12
X13
Insulation resistance 10MΩ or higher between all DC external terminals and ground (500VDC
insulation resistance tester)

XC
XD
XE
XF
X1011121314 151617 X1819 1A1B1C1D1E1F
X8 9 A B C D E F
Weight 0.16kg

XA
XB
X8
X9
A J65SBTC1-32D
External Communication part, 7-point two-piece terminal block
connection module power supply part [Transmission circuit, module power supply, FG]

X4
X5
X6
X7
system M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)

X0
X1
X2
X3
X0 1 2 3 4 5 6 7
Applicable solderless terminal: 2 or less
I/O power supply part 2-point direct-mount terminal block

(FG)
24G
[I/O power supply]

DA DG +24V
M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less DB SLD

I/O part Dedicated one-touch connector [I/O signals]

4-pin IDC plug is sold separately.
Module mounting screw M4 screw with plain washer finished round
(tightening torque range: 0.78 to 1.08 N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable Communication part, Applicable y RAV1.25-3 (compliant with JIS C 2805)
wire size module power supply solderless [Applicable wire size: 0.3 to 1.25mm2]
part terminal y V2-MS3, RAP2-3SL, TGV2-3N
I/O power supply part [Applicable wire size: 1.25 to 2.0mm2]
I/O part φ1.0 to 1.4 (A6CON-P214), φ1.4 to 2.0 (A6CON-P220)
[Applicable wire size: 0.14 to 0.2 mm2]
φ1.0 to 1.4 (A6CON-P514), φ1.4 to 2.0 (A6CON-P520)
[Applicable wire size: 0.3 to 0.5 mm2]
Accessory User’s manual

4 - 59 4 - 59
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection
Terminal
Signal name
number
TB1 DA
TB2 DB
TB3 DG
TB4 SLD
TB5 +24V
TB6 (FG)
1 DA
2 DB TB7 24G
3 DG Insulation Pin number Signal name
4 SLD 1 X0
5 +24V
2 X1
6 FG CON1
7 24G 3 X2
Module power supply 4 X3
CON1
1 1 X4
2 2 X5
CON2
3 3 X6
4
4 X7
1 X8
2 X9
CON3
3 XA
4 XB
1 XC
2 XD
CON4
3 XE
4 XF
1 X10
2 X11
CON5
3 X12
4 X13
CON8
1 1 X14
2 2 X15
CON6
3 3 X16
4
4 X17
1 X18
2 X19
CON7
8 COM 3 X1A
9 COM 4 X1B
1 X1C
2 X1D
CON8
3 X1E
4 X1F
Terminal
Signal name
number
TB8 COM
TB9 COM
Pin layout

Viewed from the front of the module

4 - 60 4 - 60
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

4.4.7 AJ65SBTC1-32D1 24VDC input module (positive common (sink), negative common
(source) loading)

Type DC input module

Item AJ65SBTC1-32D1 Appearance
Number of input points 32 points
Isolation method Photocoupler
Rated input voltage 24VDC
Rated input current Approx. 5mA
Operating voltage range 19.2 to 26.4VDC (ripple ratio: within 5%)
Max. number of simultaneous input points 100%
ON voltage/ON current 15VDC or higher/3mA or higher
OFF voltage/OFF current 3VDC or lower/0.5mA or lower
Input resistance Approx. 4.7kΩ
OFF→ON 0.2ms or less (at 24VDC)
Response time
ON→OFF 0.2ms or less (at 24VDC)
Wiring method for common 32 points/common (2 points) (1-wire, one-touch connector type)
Input type Positive/negative common shared type (sink/source shared type)

ON

COM
Number of occupied stations 32-point assignment/station (32 points used)

COM
B RATE
40 20 10 8 4 2 1 4 2 1
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
Modulepower supply

X1C
X1D
X1E
X1F
Current 45mA or lower (at 24VDC and all points ON)

STATION NO.
Noise voltage 500Vp-p, noise width 1µs,

X1A
X1B
X18
X19
Noise immunity
noise frequency 25 to 60Hz (DC type noise simulator condition)

X14
X15
X16
X17
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

X10-X1F
10MΩ or higher between all DC external terminals and ground (500VDC

X0-XF

X10
X11
X12
X13
Insulation resistance
insulation resistance tester)

XC
XD
XE
XF
X1011121314 1516 17 X1819 1A1B1C1D1E1F
X8 9 A B C D E F
Protection degree IP2X
Weight 0.16kg

XA
XB
X8
X9
A J65SBTC1-32D1
External Communication part, 7-point two-piece terminal block

X4
X5
X6
X7
connection module power supply part [Transmission circuit, module power supply, FG]

X0
X1
X2
X3
system M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m) X0 1 2 3 4 5 6 7
Applicable solderless terminal: 2 or less

(FG)
24G
I/O power supply part 2-point direct-mount terminal block
[I/O power supply] DA DG +24V
M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m) SLD

Applicable solderless terminal: 2 or less

DB

I/O part Dedicated one-touch connector [I/O signals]

4-pin IDC plug is sold separately.
Module mounting screw M4 screw with plain washer finished round
(tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable Communication part, Applicable y RAV1.25-3 (compliant with JIS C 2805)
wire size module power supply solderless [Applicable wire size: 0.3 to 1.25mm2]
part terminal y V2-MS3, RAP2-3SL, TGV2-3N
I/O power supply part [Applicable wire size: 1.25 to 2.0mm2]
I/O part φ1.0 to 1.4 (A6CON-P214), φ1.4 to 2.0 (A6CON-P220)
[Applicable wire size: 0.14 to 0.2 mm2]
φ1.0 to 1.4 (A6CON-P514), φ1.4 to 2.0 (A6CON-P520)
[Applicable wire size: 0.3 to 0.5 mm2]
Accessory User’s manual

4 - 61 4 - 61
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection
Terminal
Signal name
number
TB1 DA
TB2 DB
TB3 DG
TB4 SLD
TB5 +24V
1 DA TB6 (FG)
2 DB TB7 24G
3 DG Insulation
Pin number Signal name
4 SLD
5 +24V 1 X0
6 FG 2 X1
7 24G
CON1
3 X2
Module power supply
CON1 4 X3
1 1 X4
2 2 X5
3 CON2
3 X6
4
4 X7
1 X8
2 X9
CON3
3 XA
4 XB
1 XC
2 XD
CON4
3 XE
4 XF
1 X10
2 X11
CON5
3 X12
4 X13
CON8
1 X14
1
2 2 X15
CON6
3 3 X16
4 4 X17
1 X18
2 X19
CON7
3 X1A
8 COM
4 X1B
9 COM
1 X1C
2 X1D
CON8
3 X1E
4 X1F
Terminal
Signal name
number
TB8 COM
TB9 COM
Pin layout

Viewed from the front of the module

4 - 62 4 - 62
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

4.5 FCN Connector Type Input Module

4.5.1 AJ65SBTCF1-32D 24VDC input module (positive common (sink), negative common
(source) loading)
Type DC input module
Item AJ65SBTCF1-32D Appearance
Number of input points 32 points
Isolation method Photocoupler
Rated input voltage 24VDC
Rated input current Approx. 5mA
Operating voltage range 19.2 to 26.4VDC (ripple ratio: within 5%)
Max. number of simultaneous input points 100%
ON voltage/ON current 14VDC or higher/3.5mA or higher
OFF voltage/OFF current 6VDC or lower/1.7mA or lower
Input resistance Approx. 4.7kΩ
Response time OFF→ON 1.5ms or less (at 24VDC)
ON→OFF 1.5ms or less (at 24VDC)
Wiring method for common 32 points/common (1-wire, FCN connector type)

ON
Input type Positive/negative common shared type (sink/source shared type)

X0 X1 X2 X3 X4 X5 X6 X7 X8 X9 XA XB XC XD XE XF NC NC COM COM
B RATE

X10 X11 X12 X13 X14 X15 X16 X17 X18 X19 X1A X1B X1C X1D X1E X1F NC NC NC NC
40 20 10 8 4 2 1 4 2 1
Number of occupied stations 32-point assignment/station (32 points used)
Module power supply Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

STATION NO.
Current 45mA or lower (at 24VDC and all points ON)
Noise immunity Noise voltage 500Vp-p, noise width 1µs,
noise frequency 25 to 60Hz (DC type noise simulator condition)
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

X10-X1F
X0-XF
Insulation resistance 10MΩ or higher between all DC external terminals and ground (500VDC

X10 111213 1415 1617 X18191A1B1C1D1E1F

X8 9 A B C D E F
insulation resistance tester)
Protection degree IP2X

A J65SBTCF1-32D
Weight 0.15kg
External Communication part, 7-point two-piece terminal block
connection module power supply part [Transmission circuit, module power supply, FG]
X0 1 2 3 4 5 6 7

system M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)

(FG)
Applicable solderless terminal: 2 or less 24G

I/O power supply part, 40-pin connector [I/O power supply, I/O signal]
+24V

I/O part (A6CON1, A6CON2, A6CON3, A6CON4)

SLD
DA DG

Module mounting screw M4 screw with plain washer finished round

DB

(tightening torque range: 0.78 to 1.08N•m)

Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable Communication Applicable y RAV1.25-3 (compliant with JIS C 2805)
wire size part, solderless [Applicable wire size: 0.3 to 1.25mm2]
module power terminal y V2-MS3, RAP2-3SL, TGV2-3N
supply part [Applicable wire size: 1.25 to 2.0mm2]
I/O power supply part, 0.3mm2 (AWG22) or less (A6CON1 and A6CON4)
I/O part 0.2 to 0.08mm2 (AWG28 to 24) (A6CON2)
0.08mm2 (AWG28) stranded wire, φ0.25mm (AWG30) single wire
(A6CON3)
Applicable connector/ A6TBXY36, A6TBXY54, A6TBX70
terminal block conversion module
Accessory User’s manual

4 - 63 4 - 63
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection
Pin layout Terminal number Signal name
TB1 DA
1 DA TB2 DB
2 DB TB3 DG
3 DG Insulation TB4 SLD
4 SLD
5 +24V TB5 +24V
6 FG TB6 (FG)
7 24G
Module power supply TB7 24G
Pin Signal Pin Signal
B20 X0 number name number name
B19 X1
B18 X2
B20 X0 A20 X10
B17 X3 B19 X1 A19 X11
B16 X4 B18 X2 A18 X12
B15 X5
B14
B17 X3 A17 X13
X6
B13 X7 B16 X4 A16 X14
B12 X8 B15 X5 A15 X15
B11 X9
B14 X6 A14 X16
B10 XA
B9 XB B13 X7 A13 X17
B8 XC B12 X8 A12 X18
B7 XD
B11 X9 A11 X19
B6 XE
B5 XF B10 XA A10 X1A
A20 X10 Viewed from the B9 XB A9 X1B
A19 X11 front of the B8 XC A8 X1C
A18 X12 module
A17 X13 B7 XD A7 X1D
A16 X14 B6 XE A6 X1E
A15 X15 B5 XF A5 X1F
A14 X16
A13 X17
B4 Empty A4 Empty
A12 X18 B3 Empty A3 Empty
A11 X19 B2 COM A2 Empty
A10 X1A
B1 COM A1 Empty
A9 X1B
A8 X1C
A7 X1D
A6 X1E
A5 X1F
B2 COM
B1 COM

4 - 64 4 - 64
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

4.6 Waterproof Type Input Module

4.6.1 AJ65FBTA4-16D 24VDC input module (positive common (sink type))

Type DC input module

Item AJ65FBTA4-16D Appearance
Number of input points 16 points
Isolation method Photocoupler
Rated input voltage 24VDC
Rated input current Approx. 7mA
Operating voltage range 20.4 to 26.4VDC (ripple ratio: within 5%)
Max. number of simultaneous input points 100%
ON voltage/ON current 14VDC or higher/3.5mA or higher
OFF voltage/OFF current 6VDC or lower/1.7mA or lower
Input resistance Approx. 3.3kΩ
Response time OFF→ON 1.5ms or less (at 24VDC)
ON→OFF 1.5ms or less (at 24VDC)
Wiring method for common 16 points/common (2- to 4-wire, waterproof connector type)
Input type Positive common (sink type)
Supply current for connected device 1.0A of lower/common
Number of occupied stations 32-point assignment/station (16 points used)
Module power supply Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
Current 40mA or lower (at 24VDC and all points ON)
Noise immunity Noise voltage 500Vp-p, noise width 1µs,
noise frequency 25 to 60Hz (DC type noise simulator condition)
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
Insulation resistance 10MΩ or higher between all DC external terminals and ground (500VDC
insulation resistance tester)
Protection degree IP67
Weight 0.40kg
Accessory User’s manual
Optional item Waterproof cap: A6CAP-WP2 (20 pieces)
Other connecting devices Refer to Section 1.6.1.

4 - 65 4 - 65
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection
Pin layout Connector for communication
Pin
LINK IN LINK OUT
number
LINK IN
4 1 SLD SLD
2
3 2 DB DB
1 Communication
circuit 3 DG DG
110
4 DA DA
LINK OUT 130
4 5 No pins Empty
2
3 Terminating resistor Connector for power supply
1 setting switch
5
Pin
UNIT POWER AUX.
LINK IN number
Male 1 +24V(UNIT) +24V(I/O)
Insulation
UNIT POWER 2 1 2 Empty Empty
1 3 4
3 3 24G(UNIT) 24G(I/O)
5
2 4 Empty Empty
4 LINK OUT
Module mounting screw (FG) 5 FG FG
Female
Connector for I/O
1 2
5
AUX.
1
4 3 Pin Signal Pin Signal
3 number name number name
5
Connector for I/O 1 +24V 1 +24V
2 UNIT POWER/AUX.
4
Male 2 X1 2 X9
X0 X8
2 5
1 X1 3 24G X9 3 24G
4-wire sensor 3 4
(sink output) Black 4
4 X0 4 X8
Detection
circuit White 2 5 Empty 5 Empty
Brown 1
Blue 3
I/O connector 1 +24V 1 +24V
5 Female 2 X3 2 XB
3-wire sensor 1
5
2 X2 XA
(sink output)
4 3 X3 3 24G XB 3 24G
Black 4
Detection 2 4 X2 4 XA
circuit
Brown 1
Blue 3
5 Empty 5 Empty
5 Front view 1 +24V 1 +24V
2 X5 2 XD
X4 XC
2-wire sensor X5 3 24G XD 3 24G
(sink output) Brown 4 4 X4 4 XC
Detection 2
circuit 1 5 Empty 5 Empty
Blue 3
5 1 +24V 1 +24V
2 X7 2 XF
X6 XE
X7 3 24G XF 3 24G
4 X6 4 XE
5 Empty 5 Empty

4 - 66 4 - 66
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

4.6.2 AJ65FBTA4-16DE 24VDC input module (negative common (source type))

Type DC input module

Item AJ65FBTA4-16DE Appearance
Number of input points 16 points
Isolation method Photocoupler
Rated input voltage 24VDC
Rated input current Approx. 7mA
Operating voltage range 20.4 to 26.4VDC (ripple ratio: within 5%)
Max. number of simultaneous input points 100%
ON voltage/ON current 14VDC or higher/3.5mA or higher
OFF voltage/OFF current 6VDC or lower/1.7mA or lower
Input resistance Approx. 3.3kΩ
Response time OFF→ON 1.5ms or less (at 24VDC)
ON→OFF 1.5ms or less (at 24VDC)
Wiring method for common 16 points/common (2- to 4-wire, waterproof connector type)
Input type Negative common (source type)
Supply current for connected device 1.0A or lower/common
Number of occupied stations 32-point assignment/station (16 points used)
Module power supply Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
Current 40mA or lower (at 24VDC and all points ON)
Noise immunity Noise voltage 500Vp-p, noise width 1µs,
noise frequency 25 to 60Hz (DC type noise simulator condition)
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
Insulation resistance 10MΩ or higher between all DC external terminals and ground (500VDC
insulation resistance tester)
Protection degree IP67
Weight 0.40kg
Accessory User’s manual
Optional item Waterproof cap: A6CAP-WP2 (20 pieces)
Other connecting devices Refer to Section 1.6.1.

4 - 67 4 - 67
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection
Pin layout Connector for communication
Pin
LINK IN LINK OUT
number
1 SLD SLD
LINK IN 4 2 DB DB
2
3 3 DG DG
1 Communication
circuit
4 DA DA
110
5 No pins Empty
LINK OUT 130
4 Connector for power supply
2
3 Terminating resistor Pin UNIT
1 setting switch AUX.
5 number POWER
+24V
LINK IN 1 +24V(I/O)
(UNIT)
Insulation Male
UNIT POWER
1
2 Empty Empty
2 1
3 3 4 24G
5 3 24G(I/O)
2 (UNIT)
4
Module mounting screw (FG) LINK OUT 4 Empty Empty
Female 5 FG FG
AUX. 1 2
1 4 5
3 Connector for I/O
3
5 Pin Signal Pin Signal
Connector for I/O 2
4 UNIT POWER/AUX. number name number name

Male
1 +24V 1 +24V
4-wire sensor 2 5
1 2 X1 2 X9
(source output) Black 4
3 4 X0 X8
Detection
White 2 X1 3 24G X9 3 24G
circuit
Brown 1 4 X0 4 X8
Blue 3 I/O connector
5 5 Empty 5 Empty
Female
3-wire sensor 1
5
2 1 +24V 1 +24V
4 3
(source output) Black 4
Detection 2 X3 2 XB
circuit
2 X2 XA
Brown 1
X3 3 24G XB 3 24G
Blue 3
5 Front view 4 X2 4 XA
5 Empty 5 Empty
1 +24V 1 +24V
2-wire sensor 2 X5 2 XD
(source output) X4 XC
Detection
Brown 4
X5 3 24G XD 3 24G
circuit 2
1 4 X4 4 XC
Blue 3
5 5 Empty 5 Empty
1 +24V 1 +24V
2 X7 2 XF
X6 XE
X7 3 24G XF 3 24G
4 X6 4 XE
5 Empty 5 Empty

4 - 68 4 - 68
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

4.6.3 AJ65SBTW4-16D 24VDC input module (positive common (sink), negative common
(source) loading)
Type DC input module
Item AJ65SBTW4-16D Appearance
Operating ambient temperature 0 to 45°C
*1 *3
Storage ambient temperature -20 to 65°C
Number of input points 16 points
Isolation method Photocoupler
Rated input voltage 24VDC
Rated input current Approx. 5mA
Operating voltage range 20.4 to 26.4VDC (ripple ratio: within 5%)
Max. number of simultaneous input
100%
points
ON voltage/ON current 14VDC or higher/3.5mA or higher
OFF voltage/OFF current 6VDC or lower/1.7mA or lower
Input resistance Approx. 4.7kΩ

AJ65SBTW4-16D
OFF→ON 1.5ms or less (at 24VDC)
Response time

L ERR.
L RUN
ON→OFF 1.5ms or less (at 24VDC)

YC
YD
YA
YB

YE
YF
Y8
Y9

STATION NO.
16 points/common (4-wire, waterproof connector type)
Wiring method for common
Same as that for the module power supply

PW

X0
X1
X2
X3
X4
X5
X6
X7

MITSUBISHI
Positive/negative common shared type (sink/source shared type)
Input type
(Selected using the switch.)
Number of occupied stations 32-point assignment/station (16 points used)

CON7

CON8
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
Module power supply 35mA or lower (at 24VDC and all points ON),
Current
excluding input current for I/O part
Noise voltage 500Vp-p, noise width 1µs,

CON5

CON6
Noise immunity
noise frequency 25 to 60Hz (DC type noise simulator condition)
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
10MΩ or higher between all DC external terminals and ground (500VDC
Insulation resistance
insulation resistance tester)

CON3

CON4
Protection degree IP67
Weight 0.70kg
7-point two-piece terminal block
[Transmission circuit, module power supply, FG]
CON1

CON2

M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)

Waterproof connector
POWER CABL

POWER CABL

External connection system [compliant with IEC 60947-5-2, M12, male, 4 pins, IP67]
(connector for I/O)
<Optional>
OUT
IN

Dustproof cap: A6CAP-DC1 (20 pieces), waterproof cap: A6CAP-WP1 (20

pieces)
LINK CABL

LINK CABL

Module top-cover mounting

0.54 to 0.64N•m
screw (M3)
Module front-cover mounting
Tightening 0.54 to 0.64N•m
screw (M3)
torque
Module mounting screw
range*2
(M4 with plain washer 1.27 to 1.47N•m
finished round)
Nut for pipe 0.99 to 1.48N•m
Applicable cable size: φ5.0 to 8.0mm
Communication part, y RAV1.25-3 (compliant with JIS C 2805)
2
Applicable module power supply part, [Applicable wire size: 0.3 to 1.25mm ]
wire size I/O power supply part y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Connector for I/O -
Accessory User’s manual, waterproof plug (2 pieces)

1: Store the wired module in the ambient temperatures of -10 to 55°C.

2: Do not apply an excessive force (39N or more) to the connected cable at the inlet of the pipe.
3: To use the wired module that has been stored exceeding the ambient temperature of 55°C, retighten the nuts.

4 - 69 4 - 69
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection (positive common (sink input))

Terminal Signal
number name
TB1 DA
LINK CABLE TB2 DB
1 DA TB3 DG
2 DB TB4 SLD
3 DG Insulation TB5 +24V
4 SLD
5 +24V TB6 (FG)
6 FG TB7 24G
7 24G
Pin Signal
POWER Source type Sink type
Module power supply and number name
CABLE
external power supply (common) 1 +24V
Module Sink/source switch 2 X8
mounting screw CON1
3 24G
4 X0
1 +24V
2 X9
CON2
3 24G
4-wire sensor 4 X1
CON1
(sink output)
Black 4 1 +24V
Detection 2
White 2 XA
circuit
Brown 1 CON3
Blue 3 3 24G
4 X2
1 +24V
2 XB
3-wire sensor CON4
CON2 3 24G
(sink output) 4
Black
Detection 4 X3
2
circuit 1 +24V
Brown 1
Blue 3 2 XC
CON5
3 24G
4 X4
1 +24V
2 XD
CON6
CON8 3 24G
2-wire sensor Brown 4 4 X5
(sink output) 2
1 +24V
Detection 1
circuit Blue 3 2 XE
CON7
3 24G
4 X6
1 +24V
2 XF
CON8
3 24G
4 X7
Pin layout

Viewed from the front of the module

4 - 70 4 - 70
4 SPECIFICATIONS FOR INPUT MODULES
MELSEC-A

External connection (negative common (source input))

Terminal Signal
number name
TB1 DA
TB2 DB
LINK CABLE
1 DA TB3 DG
2 DB TB4 SLD
3 DG Insulation TB5 +24V
4 SLD
5 +24V TB6 (FG)
6 FG TB7 24G
7 24G Signal
POWER Pin number
Module power supply and CABLE Source type Sink type name
external power supply (common) 1 +24V
Sink/source switch
Module 2 X8
mounting screw CON1
3 24G
4 X0
1 +24V
2 X9
CON2
3 24G
4-wire sensor 4 X1
CON1
(source output) 4 1 +24V
Black
Detection 2 2 XA
circuit White
1
CON3
Brown 3 24G
Blue 3
4 X2
1 +24V
2 XB
CON4
3-wire sensor CON2 3 24G
(source output) Black 4 4 X3
Detection 2
circuit 1 +24V
Brown 1
3 2 XC
Blue CON5
3 24G
4 X4
1 +24V
2 XD
2-wire sensor CON6
3 24G
(source output) CON8
4 4 X5
Detection
circuit Brown 2 1 +24V
Blue 1 2 XE
3 CON7
3 24G
4 X6
1 +24V
2 XF
CON8
3 24G
4 X7
Pin layout

Viewed from the front of the module

4 - 71 4 - 71
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

5 SPECIFICATIONS FOR OUTPUT MODULES

This chapter describes the specifications for an output module that can be connected
to the CC-Link system.

5.1 Terminal Block Type Output Module

5.1.1 AJ65SBTB1-8T transistor output module (sink type)

Type Transistor output module
Item AJ65SBTB1-8T Appearance
Number of output points 8 points
Isolation method Photocoupler
Rated load voltage 12/24VDC
Operating load voltage range 10.2 to 26.4VDC (ripple ratio: within 5%)
Max. load current 0.5A/point, 2.4A/common
Max. inrush current 1.0A, 10ms or less
Leakage current at OFF 0.25mA or lower
Max. voltage drop at ON 0.3VDC or lower (TYP.) 0.5A, 0.6VDC or lower (MAX.) 0.5A
Output type Sink type
Protection function Overload protection, overvoltage protection, overheat protection
OFF→ON 0.5ms or less
Response time
ON→OFF 1.5ms or less (resistive load)
External power supply for Voltage 10.2 to 26.4VDC (ripple ratio: within 5%) 5
output part Current 15mA or lower (TYP. 24VDC/common), excluding external load current
Surge suppressor Zener diode

COM-
CTL+
B RATE
40 20 10 8 4 2 1 4 2 1
Wiring method for common 8 points/common (1-wire, terminal block type)

Y7
Number of occupied stations 32-point assignment/station (8 points used)

Y6
Y5
STATION NO.
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
Module power supply

Y4
Current 35mA or lower (at 24VDC and all points ON)

Y3
Y2
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity

Y1
noise frequency 25 to 60Hz (DC type noise simulator condition)
ON

Y0
Y0 1 2 3 4 5 6 7

Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
10MΩ or higher between all DC external terminals and ground (500VDC
A J65SBTB1-8T
24G
(FG)

Insulation resistance
insulation resistance tester)
DA DG +24V

Protection degree IP2X

SLD

Weight 0.14kg
DB

7-point two-piece terminal block

Communication part, [Transmission circuit, module power supply, FG]
module power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
External
Applicable solderless terminal: 2 or less
connection
10-point direct-mount terminal block
system
I/O power supply part, [I/O power supply, I/O signal]
I/O part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
M4 screw with plain washer finished round
Module mounting screw (tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

5-1 5-1
 5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
1 DA TB2 DB
2 DB
TB3 DG
3 DG Insulation
4 SLD TB4 SLD
5 +24V TB5 +24V
6 FG
7 24G TB6 (FG)
Module power supply TB7 24G
Load
8 Y0 TB8 Y0
9 Y1 TB9 Y1
10 Y2
11 Y3 TB10 Y2
12 Y4 TB11 Y3
13 Y5
14 Y6 TB12 Y4
Load
15 Y7 TB13 Y5
External power supply for output part 16 CTL
17 COM-
TB14 Y6
TB15 Y7
Load power supply TB16 CTL+
Constant-voltage circuit TB17 COM-
Load
External power supply for output
part and load power supply
16 CTL (common)
17 COM-

5-2 5-2
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

5.1.2 AJ65SBTB1-8T1 transistor output module (sink type)

Type Transistor output module

Item AJ65SBTB1-8T1 Appearance
Number of output points 8 points
Isolation method Photocoupler
Rated load voltage 12/24VDC
Operating load voltage range 10.2 to 26.4VDC (ripple ratio: within 5%)
Max. load current 0.5A/point, 2.4A/common
Max. inrush current 1.0A, 10ms or less
Leakage current at OFF 0.1mA or lower
Max. voltage drop at ON 0.3VDC or lower (TYP.) 0.5A, 0.6VDC or lower (MAX.) 0.5A
Output type Sink type
Protection function None
OFF→ON 0.5ms or less
Response time
ON→OFF 1.5ms or less (resistive load)
External power supply for Voltage 10.2 to 26.4VDC (ripple ratio: within 5%)
output part Current 15mA or lower (TYP. 24VDC/common), excluding external load current
Surge suppressor Zener diode

COM-
CTL+
B RATE
40 20 10 8 4 2 1 4 2 1
Wiring method for common 8 points/common (1-wire, terminal block type)

Y7
Number of occupied stations 32-point assignment/station (8 points used)

Y6
Y5
STATION NO.
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
Module power supply

Y4
Current 35mA or lower (at 24VDC and all points ON)

Y3
Y2
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity

Y1
noise frequency 25 to 60Hz (DC type noise simulator condition)

ON

Y0
Y0 1 2 3 4 5 6 7
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
10MΩ or higher between all DC external terminals and ground (500VDC

A J65SBTB1-8T1
24G
(FG)
Insulation resistance
insulation resistance tester)

+24V
Protection degree IP2X

SLD
Weight 0.14kg

DG
DB
7-point two-piece terminal block

DA
Communication part, [Transmission circuit, module power supply, FG]
module power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
External
Applicable solderless terminal: 2 or less
connection
10-point direct-mount terminal block
system
I/O power supply part, [I/O power supply, I/O signal]
I/O part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
M4 screw with plain washer finished round
Module mounting screw (tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

5-3 5-3
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
1 DA TB2 DB
2 DB
TB3 DG
3 DG Insulation
4 SLD TB4 SLD
5 +24V TB5 +24V
6 FG
7 24G TB6 (FG)
Module power supply
TB7 24G
Load TB8 Y0
8 Y0
9 Y1 TB9 Y1
10 Y2
TB10 Y2
11 Y3
12 Y4 TB11 Y3
13 Y5
TB12 Y4
Load 14 Y6
15 Y7 TB13 Y5
External power supply for output part 16 CTL+ TB14 Y6
17 COM-
TB15 Y7
TB16 CTL+
Load power supply
TB17 COM-
Constant-voltage circuit
Load
External power supply for output
part and load power supply
16 CTL+ (common)
17 COM-

5-4 5-4
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

5.1.3 AJ65SBTB2-8T transistor output module (sink type)

Type Transistor output module

Item AJ65SBTB2-8T Appearance
Number of output points 8 points
Isolation method Photocoupler
Rated load voltage 12/24VDC
Operating load voltage range 10.2 to 26.4VDC (ripple ratio: within 5%)
Max. load current 0.5A/point, 2.4A/common
Max. inrush current 1.0A, 10ms or less
Leakage current at OFF 0.25mA or lower
Max. voltage drop at ON 0.3VDC or lower (TYP.) 0.5A, 0.6VDC or lower (MAX.) 0.5A
Output type Sink type
Protection function Overload protection, overvoltage protection, overheat protection
OFF→ON 0.5ms or less
Response time
ON→OFF 1.5ms or less (resistive load)

DC24G
External power supply for Voltage 10.2 to 26.4VDC (ripple ratio: within 5%)

DC24V
B RATE
40 20 10 8 4 2 1 4 2 1

COM
output part Current 17.8mA or lower (TYP. 24VDC/common), excluding external load current

Y7
COM
Surge suppressor Zener diode

STATION NO.

Y6
Wiring method for common 8 points/common (2-wire, terminal block type)

COM
Number of occupied stations 32-point assignment/station (8 points used)

Y5
COM
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

ON
Module power supply

Y4
COM
Current 45mA or lower (at 24VDC and all points ON)

Y3
Noise voltage 500Vp-p, noise width 1µs,

COM
Noise immunity
noise frequency 25 to 60Hz (DC type noise simulator condition)

Y2
COM
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

AJ65SBTB2-8T
Y1
10MΩ or higher between all DC external terminals and ground (500VDC

COM
Insulation resistance
insulation resistance tester)

Y0
Y0 1 2 3 4 5 6 7
Protection degree IP2X
Weight 0.18kg

(FG)
24G
7-point two-piece terminal block

DA DG +24V
Communication part, [Transmission circuit, module power supply, FG]

SLD
module power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
External

DB
Applicable solderless terminal: 2 or less
connection
18-point direct-mount terminal block
system
I/O power supply part, [I/O power supply, I/O signal]
I/O part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
M4 screw with plain washer finished round
Module mounting screw (tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

5-5 5-5
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
TB2 DB
1 DA TB3 DG
2 DB
3 DG
TB4 SLD
Insulation
4 SLD TB5 +24V
5 +24V
TB6 (FG)
6 FG
7 24G TB7 24G
Module power supply
TB8 Y0
Load
8 Y0 TB9 COM
9 COM
TB10 Y1
10 Y1
11 COM TB11 COM
12 Y2 TB12 Y2
13 COM
14 Y3 TB13 COM
15 COM TB14 Y3
16 Y4
TB15 COM
17 COM
18 Y5 TB16 Y4
19 COM TB17 COM
20 Y6
21 COM TB18 Y5
Load
22 Y7 TB19 COM
23 COM
24 DC24V
TB20 Y6
25 DC24G TB21 COM
External power supply for output part
TB22 Y7
TB23 COM
Constant-voltage circuit TB24 DC24V
TB25 DC24G

5-6 5-6
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

5.1.4 AJ65SBTB2-8T1 transistor output module (sink type)

Type Transistor output module

Item AJ65SBTB2-8T1 Appearance
Number of output points 8 points
Isolation method Photocoupler
Rated load voltage 12/24VDC
Operating load voltage range 10.2 to 26.4VDC (ripple ratio: within 5%)
Max. load current 0.5A/point, 2.4A/common
Max. inrush current 1.0A, 10ms or less
Leakage current at OFF 0.1mA or lower
Max. voltage drop at ON 0.3VDC or lower (TYP.) 0.5A, 0.6VDC or lower (MAX.) 0.5A
Output type Sink type
Protection function None
OFF→ON 0.5ms or less
Response time
ON→OFF 1.5ms or less (resistive load)

DC24G
External power supply for Voltage 10.2 to 26.4VDC (ripple ratio: within 5%)

DC24V
B RATE
40 20 10 8 4 2 1 4 2 1

COM
output part Current 17.8mA or lower (TYP. 24VDC/common), excluding external load current

Y7
COM
Surge suppressor Zener diode

STATION NO.

Y6
Wiring method for common 8 points/common (2-wire, terminal block type)

COM
Number of occupied stations 32-point assignment/station (8 points used)

Y5
COM
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

ON
Module power supply

Y4
Current 45mA or lower (at 24VDC and all points ON)

COM
Y3
Noise voltage 500Vp-p, noise width 1µs,

COM
Noise immunity
noise frequency 25 to 60Hz (DC type noise simulator condition)

Y2
COM
AJ65SBTB2-8T1
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

Y1
10MΩ or higher between all DC external terminals and ground (500VDC

COM
Insulation resistance
insulation resistance tester)

Y0
Y0 1 2 3 4 5 6 7
Protection degree IP2X
Weight 0.18kg

(FG)
24G
7-point two-piece terminal block

DA DG +24V
Communication part, [Transmission circuit, module power supply, FG]

SLD
module power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
External

DB
Applicable solderless terminal: 2 or less
connection
18-point direct-mount terminal block
system
I/O power supply part, [I/O power supply, I/O signal]
I/O part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
M4 screw with plain washer finished round
Module mounting screw (tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

5-7 5-7
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
TB2 DB
TB3 DG
1 DA
2 DB TB4 SLD
3 DG
Insulation TB5 +24V
4 SLD
TB6 (FG)
5 +24V
6 FG TB7 24G
7 24G
Module power supply TB8 Y0
Load TB9 COM
8 Y0
TB10 Y1
9 COM
10 Y1 TB11 COM
11 COM
TB12 Y2
12 Y2
13 COM TB13 COM
14 Y3 TB14 Y3
15 COM
16 Y4 TB15 COM
17 COM TB16 Y4
18 Y5
TB17 COM
19 COM
20 Y6 TB18 Y5
Load 21 COM TB19 COM
22 Y7
23 COM TB20 Y6
24 DC24V TB21 COM
25 DC24G
External power supply for output part TB22 Y7

Constant-voltage circuit TB23 COM

TB24 DC24V
TB25 DC24G

5-8 5-8
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

5.1.5 AJ65SBTB1-16T transistor output module (sink type)

Type Transistor output module

Item AJ65SBTB1-16T Appearance
Number of output points 16 points
Isolation method Photocoupler
Rated load voltage 12/24VDC
Operating load voltage range 10.2 to 26.4VDC (ripple ratio: within 5%)
Max. load current 0.5A/point, 3.6A/common
Max. inrush current 1.0A, 10ms or less
Leakage current at OFF 0.25mA or lower
Max. voltage drop at ON 0.3VDC or lower (TYP.) 0.5A, 0.6VDC or lower (MAX.) 0.5A
Output type Sink type
Protection function Overload protection, overvoltage protection, overheat protection
OFF→ON 0.5ms or less
Response time
ON→OFF 1.5ms or less (resistive load)

COM-
External Power supply for Voltage 10.2 to 26.4VDC (ripple ratio: within 5%)

CTL+
B RATE
40 20 10 8 4 2 1 4 2 1

YF
output part Current 30mA or lower (TYP. 24VDC/common), excluding external load current

YE
YD
Surge suppressor Zener diode

STATION NO.

YC
Wiring method for common 16 points/common (1-wire, terminal block type)

YB
Number of occupied stations 32-point assignment/station (16 points used)

YA
Y9
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

ON
Module power supply

Y8
Current 50mA or lower (at 24VDC and all points ON)

Y7
Y6
Noise voltage 500Vp-p, noise width 1µs,

Y8 9 A B C D E F
Noise immunity

Y5
noise frequency 25 to 60Hz (DC type noise simulator condition)

Y4
AJ65SBTB1-16T

Y3
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

Y2
10MΩ or higher between all DC external terminals and ground (500VDC

Y1
Insulation resistance
insulation resistance tester)

Y0
Y0 1 2 3 4 5 6 7
Protection degree IP2X
Weight 0.18kg

(FG)
24G
7-point two-piece terminal block

DA DG +24V
Communication part, [Transmission circuit, module power supply, FG]

SLD
module power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
External

DB
Applicable solderless terminal: 2 or less
connection
18-point direct-mount terminal block
system
I/O power supply part, [I/O power supply, I/O signal]
I/O part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
M4 screw with plain washer finished round
Module mounting screw (tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

5-9 5-9
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
TB2 DB
1 DA
2 DB TB3 DG
3 DG Insulation TB4 SLD
4 SLD
5 +24V TB5 +24V
6 FG
7 24G
TB6 (FG)
Module power supply
TB7 24G
Load
8 Y0 TB8 Y0
9 Y1
10 Y2
TB9 Y1
11 Y3 TB10 Y2
12 Y4
13 Y5 TB11 Y3
14 Y6 TB12 Y4
15 Y7
16 Y8 TB13 Y5
17 Y9
TB14 Y6
18 YA
19 YB TB15 Y7
20 YC
TB16 Y8
21 YD
Load 22 YE TB17 Y9
23 YF
24 CTL+
TB18 YA
External power supply for output part
25 COM- TB19 YB
TB20 YC
Load power supply Constant-voltage circuit
TB21 YD
TB22 YE
Load TB23 YF
External power supply for output TB24 CTL+
part and load power supply
24 CTL+
(common) TB25 COM-
25 COM-

5 - 10 5 - 10
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

5.1.6 AJ65SBTB1-16T1 transistor output module (sink type)

Type Transistor output module

Item AJ65SBTB1-16T1 Appearance
Number of output points 16 points
Isolation method Photocoupler
Rated load voltage 12/24VDC
Operating load voltage range 10.2 to 26.4VDC (ripple ratio: within 5%)
Max. load current 0.5A/point, 3.6A/common
Max. inrush current 1.0A, 10ms or less
Leakage current at OFF 0.1mA or lower
Max. voltage drop at ON 0.3VDC or lower (TYP.) 0.5A, 0.6VDC or lower (MAX.) 0.5A
Output type Sink type
Protection function None
OFF→ON 0.5ms or less
Response time
ON→OFF 1.5ms or less (resistive load)

COM-
External power supply for Voltage 10.2 to 26.4VDC (ripple ratio: within 5%)

CTL+
B RATE
40 20 10 8 4 2 1 4 2 1

YF
output part Current 30mA or lower (TYP. 24VDC/common), excluding external load current

YE
YD
Surge suppressor Zener diode

STATION NO.

YC
Wiring method for common 16 points/common (1-wire, terminal block type )

YB
Number of occupied stations 32-point assignment/station (16 points used)

YA
Y9
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

ON
Module power supply

Y8
Current 50mA or lower (at 24VDC and all points ON)

Y7
Y6
Noise voltage 500Vp-p, noise width 1µs,

Y8 9 A B C D E F
Noise immunity

Y5
noise frequency 25 to 60Hz (DC type noise simulator condition)

Y4
AJ65SBTB1-16T1

Y3
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

Y2
10MΩ or higher between all DC external terminals and ground (500VDC

Y1
Insulation resistance
insulation resistance tester)

Y0
Y0 1 2 3 4 5 6 7
Protection degree IP2X
Weight 0.18kg

(FG)
24G
7-point two-piece terminal block

DA DG +24V
Communication part, [Transmission circuit, module power supply, FG]

SLD
module power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
External

DB
Applicable solderless terminal: 2 or less
connection
18-point direct-mount terminal block
system
I/O power supply part, [I/O power supply, I/O signal]
I/O part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
M4 screw with plain washer finished round
Module mounting screw (tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

5 - 11 5 - 11
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
TB2 DB
1 DA
2 DB TB3 DG
3 DG Insulation TB4 SLD
4 SLD
5 +24V TB5 +24V
6 FG TB6 (FG)
7 24G
Module power supply TB7 24G
Load TB8 Y0
8 Y0
9 Y1 TB9 Y1
10 Y2
11 Y3 TB10 Y2
12 Y4 TB11 Y3
13 Y5
14 Y6 TB12 Y4
15 Y7 TB13 Y5
16 Y8
17 Y9 TB14 Y6
18 YA TB15 Y7
19 YB
20 YC TB16 Y8
21 YD TB17 Y9
Load 22 YE
23 YF TB18 YA
24 CTL+ TB19 YB
External power supply for output part
25 COM-
TB20 YC
TB21 YD
Load power supply Constant-voltage circuit
TB22 YE
Load
External power supply for output TB23 YF
part and load power supply TB24 CTL+
24 CTL+ (common)
25 COM- TB25 COM-

5 - 12 5 - 12
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

5.1.7 AJ65SBTB2-16T transistor output module (sink type)

Type Transistor output module

Item AJ65SBTB2-16T Appearance
Number of output points 16 points
Isolation method Photocoupler
Rated load voltage 12/24VDC
Operating load voltage range 10.2 to 26.4VDC (ripple ratio: within 5%)
Max. load current 0.5A/point, 3.6A/common
Max. inrush current 1.0A, 10ms or less
Leakage current at OFF 0.25mA or lower
Max. voltage drop at ON 0.3VDC or lower (TYP.) 0.5A, 0.6VDC or lower (MAX.) 0.5A
Output type Sink type

DC24G
Protection function Overload protection, overvoltage protection, overheat protection

DC24V
40 20 10 8 4 2 1 4 2 1
B RATE

COM
OFF→ON 0.5ms or less

YF
Response time

COM
STATION NO.
ON→OFF 1.5ms or less (resistive load)

YE
COM
External power supply for Voltage 10.2 to 26.4VDC (ripple ratio: within 5%)

YD
COM
output part Current 24.2mA or lower (TYP. 24VDC/common), excluding external load current

ON

YC
COM
Surge suppressor Zener diode

YB
Wiring method for common 16 points/common (2-wire, terminal block type)

COM
YA
Number of occupied stations 32-point assignment/station (16 points used)

COM
Y9
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

COM
Module power supply
Current 55mA or lower (at 24VDC and all points ON)

Y8
COM
Noise voltage 500Vp-p, noise width 1µs,

Y7
Noise immunity

COM
noise frequency 25 to 60Hz (DC type noise simulator condition)

Y6
COM
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

Y5
COM
10MΩ or higher between all DC external terminals and ground (500VDC insulation
Insulation resistance

Y4
resistance tester)

COM
Y3
Protection degree IP2X

COM
Y8 9 A B C D E F
Weight 0.25kg

Y2
COM
AJ65SBTB2-16T
7-point two-piece terminal block

Y1
COM
Communication part, [Transmission circuit, module power supply, FG]

Y0
PW L RUN L ERR. Y0 1 2 3 4 5 6 7

module power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
External
Applicable solderless terminal: 2 or less

(FG)
24G
connection
34-point direct-mount terminal block DG +24V
system SLD
I/O power supply part, [I/O power supply, I/O signal]
I/O part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
DB
DA

Applicable solderless terminal: 2 or less

M4 screw with plain washer finished round
Module mounting screw (tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

5 - 13 5 - 13
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
TB2 DB
TB3 DG
1 DA
TB4 SLD
2 DB
3 DG Insulation
TB5 +24V
4 SLD TB6 (FG)
5 +24V
TB7 24G
6 FG
7 24G TB8 Y0
Module power supply TB9 COM
Load
8 Y0 TB10 Y1
9 COM TB11 COM
10 Y1
TB12 Y2
11 COM
12 Y2 TB13 COM
13 COM TB14 Y3
14 Y3
TB15 COM
15 COM
16 Y4 TB16 Y4
17 COM TB17 COM
18 Y5
TB18 Y5
19 COM
20 Y6 TB19 COM
21 COM TB20 Y6
22 Y7
TB21 COM
23 COM
24 Y8 TB22 Y7
25 COM TB23 COM
26 Y9
TB24 Y8
27 COM
28 YA TB25 COM
29 COM TB26 Y9
30 YB
TB27 COM
31 COM
32 YC TB28 YA
33 COM TB29 COM
34 YD
TB30 YB
35 COM
36 YE TB31 COM
Load 37 COM TB32 YC
38 YF
TB33 COM
39 COM
40 DC24V TB34 YD
41 DC24G TB35 COM
External power supply for output part
TB36 YE
TB37 COM
Constant-voltage circuit TB38 YF
TB39 COM
TB40 DC24V
TB41 DC24G

5 - 14 5 - 14
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

5.1.8 AJ65SBTB2-16T1 transistor output module (sink type)

Type Transistor output module

Item AJ65SBTB2-16T1 Appearance
Number of output points 16 points
Isolation method Photocoupler
Rated load voltage 12/24VDC
Operating load voltage range 10.2 to 26.4VDC (ripple ratio: within 5%)
Max. load current 0.5A/point, 3.6A/common
Max. inrush current 1.0A, 10ms or less
Leakage current at OFF 0.1mA or lower
Max. voltage drop at ON 0.3VDC or lower (TYP.) 0.5A, 0.6VDC or lower (MAX.) 0.5A
Output type Sink type

DC24G
Protection function None

DC24V
B RATE
40 20 10 8 4 2 1 4 2 1

COM
OFF→ON 0.5ms or less

YF
Response time

COM
STATION NO.
ON→OFF 1.5ms or less (resistive load)

YE
COM
External power supply for Voltage 10.2 to 26.4VDC (ripple ratio: within 5%)

YD
COM
output part Current 24.2mA or lower (TYP. 24VDC/common), excluding external load current

ON

YC
COM
Surge suppressor Zener diode

YB
Wiring method for common 16 points/common (2-wire, terminal block type)

COM
YA
Number of occupied stations 32-point assignment/station (16 points used)

COM
Y9
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

COM
Module power supply
Current 55mA or lower (at 24VDC and all points ON)

Y8
COM
Noise voltage 500Vp-p, noise width 1µs,

Y7
Noise immunity

COM
noise frequency 25 to 60Hz (DC type noise simulator condition)

Y6
COM
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

Y5
COM
10MΩ or higher between all DC external terminals and ground (500VDC insulation
Insulation resistance

Y4
resistance tester)

COM
Y3
Protection degree IP2X

COM
Y8 9 A B C D E F

Y2
Weight 0.25kg

AJ65SBTB2-16T1

COM
7-point two-piece terminal block

Y1
COM
Communication part, [Transmission circuit, module power supply, FG]

Y0
PW L RUN L ERR. Y0 1 2 3 4 5 6 7
module power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
External
Applicable solderless terminal: 2 or less

(FG)
24G
connection
34-point direct-mount terminal block +24V
system SLD
I/O power supply part, [I/O power supply, I/O signal]
DG

I/O part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)

DB
DA

Applicable solderless terminal: 2 or less

M4 screw with plain washer finished round
Module mounting screw (tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

5 - 15 5 - 15
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
TB2 DB
TB3 DG
1 DA TB4 SLD
2 DB
3 DG TB5 +24V
Insulation
4 SLD TB6 (FG)
5 +24V TB7 24G
6 FG
7 24G TB8 Y0
Module power supply TB9 COM
Load
8 Y0 TB10 Y1
9 COM TB11 COM
10 Y1
TB12 Y2
11 COM
12 Y2 TB13 COM
13 COM TB14 Y3
14 Y3
TB15 COM
15 COM
16 Y4 TB16 Y4
17 COM TB17 COM
18 Y5
TB18 Y5
19 COM
20 Y6 TB19 COM
21 COM TB20 Y6
22 Y7
TB21 COM
23 COM
24 Y8 TB22 Y7
25 COM TB23 COM
26 Y9
TB24 Y8
27 COM
28 YA TB25 COM
29 COM TB26 Y9
30 YB
TB27 COM
31 COM
32 YC TB28 YA
33 COM TB29 COM
34 YD
35 COM
TB30 YB
36 YE TB31 COM
37 COM TB32 YC
Load
38 YF
39 COM
TB33 COM
40 DC24V TB34 YD
41 DC24G TB35 COM
External power supply for output part
TB36 YE
TB37 COM
Constant-voltage circuit TB38 YF
TB39 COM
TB40 DC24V
TB41 DC24G

5 - 16 5 - 16
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

5.1.9 AJ65SBTB1-32T transistor output module (sink type)

Type Transistor output module

Item AJ65SBTB1-32T Appearance
Number of output points 32 points
Isolation method Photocoupler
Rated load voltage 12/24VDC
Operating load voltage range 10.2 to 26.4VDC (ripple ratio: within 5%)
Max. load current 0.5A/point, 4.8A/common
Max. inrush current 1.0A, 10ms or less
Leakage current at OFF 0.25mA or lower

Y1F COM-
Y1E CTL+
B RATE
40 20 10 8 4 2 1 4 2 1
Max. voltage drop at ON 0.3VDC or lower (TYP.) 0.5A, 0.6VDC or lower (MAX.) 0.5A
Output type Sink type

Y1D
STATION NO.
Protection function Overload protection, overvoltage protection, overheat protection

Y1C
Y1B
OFF→ON 0.5ms or less
Response time

Y1A
ON→OFF 1.5ms or less (resistive load)

Y19
Y18
External power supply for Voltage 10.2 to 26.4VDC (ripple ratio: within 5%)

ON

Y17
output part Current 50mA or lower (TYP. 24VDC/common), excluding external load current

Y16
Y15
Surge suppressor Zener diode

Y14
Wiring method for common 32 points/common (1-wire, terminal block type)

Y13
Number of occupied stations 32-point assignment/station (32 points used)

Y12
Y18 19 1A1B 1C1D1E 1F

Y11
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

Y10
Module power supply
Current 65mA or lower (at 24VDC and all points ON)

YF
YE
Noise voltage 500Vp-p, noise width 1µs,

YD
Noise immunity
noise frequency 25 to 60Hz (DC type noise simulator condition)

YC
Y10 11 12 13 14 15 16 17

YB
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

YA
10MΩ or higher between all DC external terminals and ground (500VDC

Y9
Insulation resistance
insulation resistance tester)

Y8
Y7
Protection degree IP2X

Y6
Y8 9 A B C D E F
Weight 0.25kg

Y5
Y4
7-point two-piece terminal block

AJ65SBTB1-32T

Y3
Communication part, [Transmission circuit, module power supply, FG]

Y2
Y1
module power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
External
Applicable solderless terminal: 2 or less Y0
PW L RUN L ERR. Y0 1 2 3 4 5 6 7

connection
34-point direct-mount terminal block
system
(FG)
24G

I/O power supply part, [I/O power supply, I/O signal]

I/O part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
DA DG +24V

Applicable solderless terminal: 2 or less

SLD

M4 screw with plain washer finished round

DB

Module mounting screw (tightening torque range: 0.78 to 1.08N•m)

Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

5 - 17 5 - 17
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
TB2 DB
TB3 DG
1 DA
2 DB TB4 SLD
3 DG Insulation TB5 +24V
4 SLD
TB6 (FG)
5 +24V
6 FG TB7 24G
7 24G
Module power supply TB8 Y0
Load TB9 Y1
8 Y0
9 Y1
TB10 Y2
10 Y2 TB11 Y3
11 Y3
12 Y4
TB12 Y4
13 Y5 TB13 Y5
14 Y6
TB14 Y6
15 Y7
16 Y8 TB15 Y7
17 Y9 TB16 Y8
18 YA
19 YB TB17 Y9
20 YC TB18 YA
21 YD
22 YE
TB19 YB
23 YF TB20 YC
24 Y10
TB21 YD
25 Y11
26 Y12 TB22 YE
27 Y13 TB23 YF
28 Y14
29 Y15 TB24 Y10
30 Y16 TB25 Y11
31 Y17
32 Y18
TB26 Y12
33 Y19 TB27 Y13
34 Y1A
TB28 Y14
35 Y1B
36 Y1C TB29 Y15
37 Y1D
TB30 Y16
38 Y1E
Load
39 Y1F TB31 Y17
External power supply for output part 40 CTL+ TB32 Y18
41 COM-
TB33 Y19
TB34 Y1A
Load power supply
Constant-voltage circuit TB35 Y1B
Load TB36 Y1C
External power supply for output
part and load power supply TB37 Y1D
40 CTL+ (common) TB38 Y1E
41 COM-
TB39 Y1F
TB40 CTL+
TB41 COM-

5 - 18 5 - 18
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

5.1.10 AJ65SBTB1-32T1 transistor output module (sink type)

Type Transistor output module

Item AJ65SBTB1-32T1 Appearance
Number of output points 32 points
Isolation method Photocoupler
Rated load voltage 12/24VDC
Operating load voltage range 10.2 to 26.4VDC (ripple ratio: within 5%)
Max. load current 0.5A/point, 4.8A/common
Max. inrush current 1.0A, 10ms or less
Leakage current at OFF 0.1mA or lower

Y1F COM-
Max. voltage drop at ON 0.3VDC or lower (TYP.) 0.5A, 0.6VDC or lower (MAX.) 0.5A

Y1E CTL+
B RATE
40 20 10 8 4 2 1 4 2 1
Output type Sink type
Protection function None

Y1D
STATION NO.

Y1C
OFF→ON 0.5ms or less

Y1B
Response time
ON→OFF 1.5ms or less (resistive load)

Y1A
Y19
External power supply for Voltage 10.2 to 26.4VDC (ripple ratio: within 5%)

Y18
ON
output part

Y17
Current 50mA or lower (TYP. 24VDC/common), excluding external load current

Y16
Surge suppressor Zener diode

Y15
Y14
Wiring method for common 32 points/common (1-wire, terminal block type)

Y13
Number of occupied stations 32-point assignment/station (32 points used)

Y12
Y10 11 12 13 14 15 16 17 Y18 19 1A1B1C1D1E 1F

Y11
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
Module power supply

Y10
Current 65mA or lower (at 24VDC and all points ON)

YF
YE
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity

YD
noise frequency 25 to 60Hz (DC type noise simulator condition)

YC
YB
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

YA
10MΩ or higher between all DC external terminals and ground (500VDC

Y9
Insulation resistance

Y8
insulation resistance tester)

Y7
Protection degree IP2X

Y6
Y8 9 A B C D E F

Y5
Weight 0.25kg

Y4
AJ65SBTB1-32T1
7-point two-piece terminal block

Y3
Y2
Communication part, [Transmission circuit, module power supply, FG]

Y1
module power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Y0
External
PW L RUN L ERR. Y0 1 2 3 4 5 6 7

Applicable solderless terminal: 2 or less

connection
34-point direct-mount terminal block
system
(FG)
24G

I/O power supply part, [I/O power supply, I/O signal]

DA DG +24V

I/O part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)

SLD

Applicable solderless terminal: 2 or less

DB

M4 screw with plain washer finished round

Module mounting screw (tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

5 - 19 5 - 19
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
TB2 DB
TB3 DG
1 DA
2 DB
TB4 SLD
3 DG Insulation TB5 +24V
4 SLD
5 +24V
TB6 (FG)
6 FG TB7 24G
7 24G
Module power supply TB8 Y0
Load TB9 Y1
8 Y0
9 Y1 TB10 Y2
10 Y2 TB11 Y3
11 Y3
12 Y4 TB12 Y4
13 Y5 TB13 Y5
14 Y6
15 Y7 TB14 Y6
16 Y8 TB15 Y7
17 Y9
18 YA TB16 Y8
19 YB TB17 Y9
20 YC
21 YD TB18 YA
22 YE TB19 YB
23 YF
24 Y10 TB20 YC
25 Y11 TB21 YD
26 Y12
27 Y13
TB22 YE
28 Y14 TB23 YF
29 Y15
30 Y16
TB24 Y10
31 Y17 TB25 Y11
32 Y18
33 Y19
TB26 Y12
34 Y1A TB27 Y13
35 Y1B
36 Y1C
TB28 Y14
37 Y1D TB29 Y15
38 Y1E
Load TB30 Y16
39 Y1F
External power supply for output part 40 CTL+ TB31 Y17
41 COM-
TB32 Y18
TB33 Y19
Load power supply Constant-voltage circuit TB34 Y1A
TB35 Y1B
Load
TB36 Y1C
External power supply for output
part and load power supply TB37 Y1D
40 CTL+
(common) TB38 Y1E
41 COM-
TB39 Y1F
TB40 CTL+
TB41 COM-

5 - 20 5 - 20
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

5.1.11 AJ65SBTB1-8TE transistor output module (source type)

Type Transistor output module

Item AJ65SBTB1-8TE Appearance
Number of output points 8 points
Isolation method Photocoupler
Rated load voltage 12/24VDC
Operating load voltage range 10.2 to 26.4VDC (ripple ratio: within 5%)
Max. load current 0.1A/point, 0.8A/common
Max. inrush current 1.0A, 10ms or less
Leakage current at OFF 0.1mA or lower
Max. voltage drop at ON 0.1VDC or lower (TYP.) 0.1A, 0.2VDC or lower (MAX.) 0.1A
Output type Source type
Protection function Overload protection, overheat protection
OFF→ON 0.5ms or less
Response time
ON→OFF 1.5ms or less (resistive load)
External power supply for Voltage 10.2 to 26.4VDC (ripple ratio: within 5%)
output part Current 15mA or lower (TYP. 24VDC/common), excluding external load current

CTL-
Surge suppressor Zener diode

COM+
B RATE
40 20 10 8 4 2 1 4 2 1
Wiring method for common 8 points/common (1-wire, terminal block type)

Y7
Y6
Number of occupied stations 32-point assignment/station (8 points used)

Y5
STATION NO.
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

Y4
Module power supply

Y3
Current 35mA or lower (at 24VDC and all points ON)

Y2
Noise voltage 500Vp-p, noise width 1µs,

Y1
Noise immunity

ON

Y0
noise frequency 25 to 60Hz (DC type noise simulator condition)

Y0 1 2 3 4 5 6 7
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

A J65SBTB1-8TE
24G
(FG)
10MΩ or higher between all DC external terminals and ground (500VDC
Insulation resistance
insulation resistance tester)

DA DG +24V
Weight 0.14kg

SLD
7-point two-piece terminal block

DB
Communication part, [Transmission circuit, module power supply, FG]
module power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
External
Applicable solderless terminal: 2 or less
connection
10-point direct-mount terminal block
system
I/O power supply part, [I/O power supply, I/O signal]
I/O part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
M4 screw with plain washer finished round
Module mounting screw (tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

5 - 21 5 - 21
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
1 DA TB2 DB
2 DB
TB3 DG
3 DG
Insulation
4 SLD TB4 SLD
5 +24V TB5 +24V
6 FG
TB6 (FG)
7 24G
Module power supply TB7 24G
Load TB8 Y0
8 Y0
9 Y1 TB9 Y1
10 Y2 TB10 Y2
11 Y3
12 Y4
TB11 Y3
13 Y5 TB12 Y4
Load 14 Y6 TB13 Y5
15 Y7
16 COM+
TB14 Y6
Load power supply 17 CTL- TB15 Y7
External power supply for output part TB16 COM+
TB17 CTL-

Constant-voltage circuit
Load
External power supply for output
part and load power supply
16 COM+ (common)
17 CTL-

5 - 22 5 - 22
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

5.1.12 AJ65SBTB1-16TE transistor output module (source type)

Type Transistor output module

Item AJ65SBTB1-16TE Appearance
Number of output points 16 points
Isolation method Photocoupler
Rated load voltage 12/24VDC
Operating load voltage range 10.2 to 26.4VDC (ripple ratio: within 5%)
Max. load current 0.1A/point, 1.6A/common
Max. inrush current 1.0A, 10ms or less
Leakage current at OFF 0.1mA or lower
Max. voltage drop at ON 0.1VDC or lower (TYP.) 0.1A, 0.2VDC or lower (MAX.) 0.1A
Output type Source type
Protection function Overload protection, overheat protection
OFF→ON 0.5ms or less
Response time
ON→OFF 1.5ms or less (resistive load)

CTL-
YE COM+
B RATE
40 20 10 8 4 2 1 4 2 1
External power supply for Voltage 10.2 to 26.4VDC (ripple ratio: within 5%)

YF
output part Current 30mA or lower (TYP. 24VDC/common), excluding external load current

YD
STATION NO.
Surge suppressor Zener diode

YC
YB
Wiring method for common 16 points/common (1-wire, terminal block type )

YA
Number of occupied stations 32-point assignment/station (16 points used)

Y9
ON
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

Y8
Module power supply

Y7
Current 50mA or lower (at 24VDC and all points ON)

Y6
Y8 9 A B C D E F

Y5
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity

Y4
noise frequency 25 to 60Hz (DC type noise simulator condition)

AJ65SBTB1-16TE

Y3
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

Y2
Y1
10MΩ or higher between all DC external terminals and ground (500VDC
Insulation resistance

Y0
insulation resistance tester)

Y0 1 2 3 4 5 6 7
Weight 0.18kg

(FG)
24G
7-point two-piece terminal block
Communication part, [Transmission circuit, module power supply, FG]

DA DG +24V
module power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)

SLD
External
Applicable solderless terminal: 2 or less

DB
connection
18-point direct-mount terminal block
system
I/O power supply part, [I/O power supply, I/O signal]
I/O part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
M4 screw with plain washer finished round
Module mounting screw (tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

5 - 23 5 - 23
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
1 DA TB2 DB
2 DB
3 DG
TB3 DG
Insulation
4 SLD TB4 SLD
5 +24V
TB5 +24V
6 FG
7 24G TB6 (FG)
Module power supply
TB7 24G
Load
8 Y0 TB8 Y0
9 Y1
TB9 Y1
10 Y2
11 Y3 TB10 Y2
12 Y4 TB11 Y3
13 Y5
TB12 Y4
14 Y6
15 Y7 TB13 Y5
16 Y8
TB14 Y6
17 Y9
18 YA TB15 Y7
19 YB TB16 Y8
20 YC
21 YD
TB17 Y9
Load 22 YE TB18 YA
23 YF
TB19 YB
Load power supply 24 COM
25 CTL TB20 YC
External power supply for output part TB21 YD
TB22 YE
TB23 YF
Constant-voltage circuit TB24 COM+
Load TB25 CTL-
External power supply for output
part and load power supply
24 COM (common)
25 CTL-

5 - 24 5 - 24
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

5.1.13 AJ65SBTB1B-16TE1 transistor output module (source type)

Type Transistor output module

Item AJ65SBTB1B-16TE1 Appearance
Number of output points 16 points
Isolation method Photocoupler
Rated load voltage 12/24VDC
Operating load voltage range 10.2 to 26.4VDC (ripple ratio: within 5%)
Max. load current 0.5A/point, 4A/common
Max. inrush current 1.0A, 10ms or less
Leakage current at OFF 0.1mA or lower
Max. voltage drop at ON 0.5VDC or lower (TYP.) 0.5A, 0.8VDC or lower (MAX.) 0.5A

COM1- COM1- COM1- COM1- COM1- COM1- CTL1- COM1+ COM2- COM2- COM2- COM2- COM2- COM2- CTL2- COM2+ NC
NC
B RATE
40 20 10 8 4 2 1 4 2 1
Output type Source type

YE YF
Protection function None

STATION NO.
OFF→ON 0.5ms or less
Response time
ON→OFF 1.5ms or less (resistive load)

YD
External power supply for Voltage 10.2 to 26.4VDC (ripple ratio: within 5%)

YC
ON
output part Current 10mA or lower (TYP. 24VDC/common), excluding external load current

YB
Surge suppressor Zener diode
Wiring method for common 8 points/common (1-wire, terminal block type)

YA
Number of occupied stations 32-point assignment/station (16 points used)

Y9
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
Module power supply

Y8
Current 45mA or lower (at 24VDC and all points ON)

Y7
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity
noise frequency 25 to 60Hz (DC type noise simulator condition)

Y6
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

Y5
10MΩ or higher between all DC external terminals and ground (500VDC
Insulation resistance

Y4
insulation resistance tester)
Protection degree IP2X

Y3
Y8 9 A B C D E F
Weight 0.26kg

Y2
A J65SBTB1B-16TE1
7-point two-piece terminal block

Y1
Communication part, [Transmission circuit, module power supply, FG]
module power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)

Y0
External
PW L RUN L ERR.Y0 1 2 3 4 5 6 7

Applicable solderless terminal: 2 or less

connection
34-point direct-mount terminal block (FG)
24G

system
I/O power supply part, [I/O power supply, I/O signal]
DA DG +24V

I/O part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)

DB SLD

Applicable solderless terminal: 2 or less

M4 screw with plain washer finished round
Module mounting screw (tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

5 - 25 5 - 25
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
TB2 DB
1 DA TB3 DG
2 DB
TB4 SLD
3 DG
Insulation TB5 +24V
4 SLD
5 +24V TB6 (FG)
6 FG TB7 24G
Module power supply 7 24G TB8 Y0
TB9 COM1-
Load TB10 Y1
8 Y0
9 COM1- TB11 COM1-
10 Y1 TB12 Y2
11 COM1- TB13 COM1-
12 Y2 TB14 Y3
13 COM1-
TB15 COM1-
14 Y3
15 COM1-
TB16 Y4
16 Y4 TB17 COM1-
17 COM1- TB18 Y5
18 Y5 TB19 COM1-
19 COM1- TB20 Y6
20 Y6
TB21 CTL1-
Load 21 CTL1-
TB22 Y7
22 Y7
External power supply TB23 COM1+
23 COM1+
for output part and Load
TB24 Y8
24 Y8
load power supply Constant-voltage circuit
25 COM2- TB25 COM2-
(common)
26 Y9 TB26 Y9
27 COM2-
TB27 COM2-
28 YA
TB28 YA
29 COM2-
30 YB TB29 COM2-
31 COM2- TB30 YB
32 YC TB31 COM2-
33 COM2- TB32 YC
34 YD TB33 COM2-
35 COM2-
TB34 YD
36 YE
37 CTL2-
TB35 COM2-
Load
38 YF TB36 YE
39 COM2+ TB37 CTL2-
External power supply for output part 40 Empty TB38 YF
and load power supply (common) 41 Empty Constant-voltage circuit TB39 COM2+
TB40 Empty
TB41 Empty

5 - 26 5 - 26
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

5.1.14 AJ65SBTB1-32TE1 transistor output module (source type)

Type Transistor output module

Item AJ65SBTB1-32TE1 Appearance
Number of output points 32 points
Isolation method Photocoupler
Rated load voltage 12/24VDC
Operating load voltage range 10.2 to 26.4VDC (ripple ratio: within 5%)
Max. load current 0.5A/point, 4.8A/common
Max. inrush current 1.0A, 10ms or less
Leakage current at OFF 0.1mA or lower
Max. voltage drop at ON 0.5VDC or lower (TYP.) 0.5A, 0.8VDC or lower (MAX.) 0.5A

Y17 Y19 Y1B Y1D Y1F CTL-

Y1A Y1C Y1E COM+
B RATE
40 20 10 8 4 2 1 4 2 1
Output type Source type
Protection function None

STATION NO.
OFF→ON 0.5ms or less
Response time
ON→OFF 1.5ms or less (resistive load)
External power supply for Voltage 10.2 to 26.4VDC (ripple ratio: within 5%)

ON

Y14 Y16 Y18

output part Current 15mA or lower (TYP. 24VDC/common), excluding external load current
Surge suppressor Zener diode

Y13 Y15
Wiring method for common 32 points/common (1-wire, terminal block type)
Number of occupied stations 32-point assignment/station (32 points used)

Y10 Y12
Y1819 1A 1B 1C 1D1E 1F

Y11
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
Module power supply
Current 60mA or lower (at 24VDC and all points ON)

YF
YE
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity

YD
noise frequency 25 to 60Hz (DC type noise simulator condition)

YC
Y1011 12 13 14 15 16 17

YB
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

YA
10MΩ or higher between all DC external terminals and ground (500VDC

Y9
Insulation resistance

Y8
insulation resistance tester)

Y7
Protection degree IP2X

Y6
Y8 9 A B C D E F

Y5
Weight 0.26kg

Y4
7-point two-piece terminal block

Y3
A J65SBTB1-32TE1
Y2
Communication part, [Transmission circuit, module power supply, FG]

Y1
module power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)

Y0
External
PW L RUN L ERR.Y0 1 2 3 4 5 6 7

Applicable solderless terminal: 2 or less

connection
34-point direct-mount terminal block (FG)
24G

system
I/O power supply part, [I/O power supply, I/O signal]
DA DG +24V

I/O part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)

DB SLD

Applicable solderless terminal: 2 or less

M4 screw with plain washer finished round
Module mounting screw (tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

5 - 27 5 - 27
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
1 DA TB2 DB
2 DB TB3 DG
3 DG Insulation TB4 SLD
4 SLD
5 +24V
TB5 +24V
6 FG TB6 (FG)
7 24G TB7 24G
Module power supply
TB8 Y0
Load
8 Y0 TB9 Y1
9 Y1
TB10 Y2
10 Y2
11 Y3 TB11 Y3
12 Y4 TB12 Y4
13 Y5 TB13 Y5
14 Y6
TB14 Y6
15 Y7
16 Y8 TB15 Y7
17 Y9 TB16 Y8
18 YA TB17 Y9
19 YB
TB18 YA
20 YC
21 YD TB19 YB
22 YE TB20 YC
23 YF
TB21 YD
24 Y10
25 Y11 TB22 YE
26 Y12 TB23 YF
27 Y13 TB24 Y10
28 Y14
TB25 Y11
29 Y15
30 Y16 TB26 Y12
31 Y17 TB27 Y13
32 Y18 TB28 Y14
33 Y19
34 Y1A
TB29 Y15
35 Y1B TB30 Y16
36 Y1C TB31 Y17
37 Y1D
TB32 Y18
Load 38 Y1E
39 Y1F TB33 Y19
40 COM+ TB34 Y1A
Load power supply 41 CTL- TB35 Y1B
Constant-voltage circuit
TB36 Y1C
External power supply for output part
TB37 Y1D
TB38 Y1E
Load
External power supply for output TB39 Y1F
part and load power supply TB40 COM+
40 COM+ (common) TB41 CTL-
41 CTL-

5 - 28 5 - 28
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

5.1.15 AJ65SBTB2N-8R contact output module

Type Contact output module

Item AJ65SBTB2N-8R Appearance
Number of output points 8 points
Isolation method Relay
2A/point, 4A/common
Rated load voltage/current
at 24VDC (resistive load) or 240VAC (cosφ=1)
Min. switching load 5VDC, 1mA
Max. switching voltage 264VAC, 125VDC
OFF→ON 10ms or less
Response time
ON→OFF 12ms or less
Mechanical 20 million times or more
Rated switching voltage/current load: 100 thousand times or more
Life 200VAC 1.5A, 240VAC 1A (cosφ=0.7): 100 thousand times or more
Electrical
200VAC 1A, 240VAC 0.5A (cosφ=0.35): 100 thousand times or more
24VDC 1A, 100VDC 0.1A (L/R=7ms): 100 thousand times or more
Max. switching frequency 3600 times/hour

COMB COMB COMB COMB COMB COMB COMB COMB COMB

Surge suppressor None

Y0 1 2 3 4 5 6 7

Y7 COMA
Wiring method for common 8 points/common (2-wire, terminal block type)
Number of occupied stations 32-point assignment/station (8 points used)
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

Y6
Module power supply
Current 85mA or lower (at 24VDC and all points ON)

Y5
Noise voltage: 1500Vp-p (AC type), 500Vp-p (DC type), noise width 1µs,

Y4
noise frequency 25 to 60Hz (noise simulator condition)
Noise immunity
Fast transient/burst immunity test

Y3
IEC61000-4-4:1kV

Y2
B RATE
40 20 10 8 4 2 1 4 2 1
2830VACrms for 3 cycles between all AC external terminals and ground
Withstand voltage (2000m above sea level)

Y1
STATION NO.
500VAC for 1 minute between all DC external terminals and ground

Y0
10MΩ or higher between all AC external terminals and ground (500VDC
insulation resistance tester)
Insulation resistance

(FG)
10MΩ or higher between all DC external terminals and ground (500VDC

24G
ON
A J65SBTB2N-8R

insulation resistance tester)

DA DG +24V
Weight 0.25kg SLD

7-point two-piece terminal block

DB

Communication part, [Transmission circuit, module power supply, FG]

module power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
External
Applicable solderless terminal: 2 or less
connection
18-point direct-mount terminal block
system
I/O power supply part, [I/O power supply, I/O signal]
I/O part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
M4 screw with plain washer finished round
Module mounting screw (tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

5 - 29 5 - 29
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
TB2 DB
1 DA
2 DB TB3 DG
3 DG TB4 SLD
Insulation
4 SLD TB5 +24V
5 +24V TB6 (FG)
6 FG TB7 24G
7 24G TB8 Y0
Module power supply
TB9 COM B
Load
8 Y0 TB10 Y1
9 COM B TB11 COM B
10 Y1 TB12 Y2
11 COM B TB13 COM B
12 Y2 TB14 Y3
13 COM B
TB15 COM B
14 Y3
TB16 Y4
15 COM B
TB17 COM B
16 Y4
17 COM B
TB18 Y5
18 Y5 TB19 COM B
19 COM B TB20 Y6
20 Y6 TB21 COM B
Load
21 COM B TB22 Y7
22 Y7 TB23 COM B
23 COM B TB24 COM A
24 COM A
TB25 COM B
25 COM B

External load power supply

100/200VAC or 24VDC

All COM B terminals are connected inside the module (shared common).

5 - 30 5 - 30
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

5.1.16 AJ65SBTB2N-16R contact output module

Type Contact output module

Item AJ65SBTB2N-16R Appearance
Number of output points 16 points
Isolation method Relay
2A/point, 8A/common
Rated load voltage/current
at 24VDC (resistive load) or 240VAC (cosφ=1)
Min. switching load 5VDC, 1mA
Max. switching voltage 264VAC, 125VDC
OFF→ON 10ms or less
Response time
ON→OFF 12ms or less
Mechanical 20 million times or more
Rated switching voltage/current load: 100 thousand times or more
Life 200VAC 1.5A, 240VAC 1A (cosφ=0.7): 100 thousand times or more
Electrical

COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB
200VAC 1A, 240VAC 0.5A (cosφ=0.35): 100 thousand times or more

Y8 9 A B C D E F

COMA
24VDC 1A, 100VDC 0.1A (L/R=7ms): 100 thousand times or more

YF
Max. switching frequency 3600 times/hour

YE
Surge suppressor None

PW L RUN L ERR. Y0 1 2 3 4 5 6 7

YD
Wiring method for common 16 points/common (2-wire, terminal block type)

YC
Number of occupied stations 32-point assignment/station (16 points used)
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

YB
Module power supply
Current 120mA or lower (at 24VDC and all points ON)

YA
Noise voltage: 1500Vp-p (AC type), 500Vp-p (DC type), noise width 1µs,

Y9
noise frequency 25 to 60Hz (noise simulator condition)
Noise immunity

Y8
Fast transient/burst immunity test

Y7
IEC 61000-4-4:1kV

Y6
2830VACrms for 3 cycles between all AC external terminals and ground (2000m
Withstand voltage above sea level)

Y5
500VAC for 1 minute between all DC external terminals and ground

Y4
10MΩ or higher between all AC external terminals and ground (500VDC insulation

Y3
resistance tester)
B RATE
40 20 10 8 4 2 1 4 2 1
Insulation resistance

Y2
10MΩ or higher between all DC external terminals and ground (500VDC insulation

Y1
resistance tester)
STATION NO.

Y0
Weight 0.35kg
7-point two-piece terminal block (FG)
24G
ON

Communication part, [Transmission circuit, module power supply, FG]

AJ65SBTB2N-16R

DA DG +24V

module power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
External
SLD

Applicable solderless terminal: 2 or less

connection
DB

34-point direct-mount terminal block

system
I/O power supply part, [I/O power supply, I/O signal]
I/O part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
M4 screw with plain washer finished round
Module mounting screw (tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

5 - 31 5 - 31
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
1 DA TB2 DB
2 DB TB3 DG
3 DG
Insulation TB4 SLD
4 SLD TB5 +24V
5 +24V
TB6 (FG)
6 FG
7 24G
TB7 24G
Module power supply TB8 Y0
Load TB9 COM B
8 Y0
TB10 Y1
9 COM B
10 Y1 TB11 COM B
11 COM B TB12 Y2
12 Y2 TB13 COM B
13 COM B TB14 Y3
14 Y3 TB15 COM B
15 COM B
TB16 Y4
16 Y4
17 COM B TB17 COM B
18 Y5 TB18 Y5
19 COM B TB19 COM B
20 Y6 TB20 Y6
21 COM B
TB21 COM B
22 Y7
23 COM B
TB22 Y7
24 Y8 TB23 COM B
25 COM B TB24 Y8
26 Y9 TB25 COM B
27 COM B TB26 Y9
28 YA
TB27 COM B
29 COM B
30 YB TB28 YA
31 COM B TB29 COM B
32 YC TB30 YB
33 COM B TB31 COM B
34 YD TB32 YC
35 COM B
TB33 COM B
36 YE
37 COM B TB34 YD
Load
38 YF TB35 COM B
39 COM B TB36 YE
40 COM A TB37 COM B
41 COM B
TB38 YF
External load power supply TB39 COM B
TB40 COM A
TB41 COM B

100/200VAC or 24VDC

All COM B terminals are connected inside the module (shared common).

5 - 32 5 - 32
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

5.1.17 AJ65SBTB2N-8S triac output module

Type Triac output module

Item AJ65SBTB2N-8S Appearance
Number of output points 8 points
Isolation method Photocoupler
Rated load voltage 100 to 240VAC, 50/60Hz ±5%
Load voltage distortion ratio Within 5%
Max. load voltage 264VAC
Max. load current 0.6A/point, 2.4A/common
Min. load voltage/current 50VAC 100mA, 100VAC 10mA, 240VAC 10mA
Max. inrush current 25A, 10ms or less
1.5mArms or lower (at 100VACrms, 60Hz),
Leakage current at OFF
3mArms or lower (at 200VACrms, 60Hz)
Max. voltage drop at ON 1.5VACrms or lower (at 0.6A)
OFF→ON 1ms or less
Response time
ON→OFF Total of 1ms and 0.5 cycles or less
Surge suppressor CR absorber (0.01µF + 47Ω)

COMB COMB COMB COMB COMB COMB COMB COMB COMB

Y0 1 2 3 4 5 6 7

Y7 COMA
Wiring method for common 8 points/common (2-wire, terminal block type)
Number of occupied stations 32-point assignment/station (8 points used)
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
Module power supply

Y6
Current 55mA or lower (at 24VDC and all points ON)

Y5
Noise voltage: 1500Vp-p (AC type), 500Vp-p (DC type), noise width 1µs,
noise frequency 25 to 60Hz (noise simulator condition)

Y4
Noise immunity
Fast transient/burst immunity test

Y3
IEC61000-4-4:1kV
2830VACrms for 3 cycles between all AC external terminals and ground

Y2
B RATE
40 20 10 8 4 2 1 4 2 1
Withstand voltage (2000m above sea level)

Y1
500VAC for 1 minute between all DC external terminals and ground

STATION NO.
10MΩ or higher between all AC external terminals and ground (500VDC

Y0
insulation resistance tester)
Insulation resistance
10MΩ or higher between all DC external terminals and ground (500VDC

(FG)
24G
insulation resistance tester) ON
AJ65SBTB2N-8S

+24V
Weight 0.25kg
7-point two-piece terminal block SLD
DA DG

Communication part, [Transmission circuit, module power supply, FG]

DB

module power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
External
Applicable solderless terminal: 2 or less
connection
18-point direct-mount terminal block
system
I/O power supply part, [I/O power supply, I/O signal]
I/O part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
M4 screw with plain washer finished round
Module mounting screw (tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

5 - 33 5 - 33
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
1 DA TB2 DB
2 DB TB3 DG
3 DG TB4 SLD
Insulation
4 SLD TB5 +24V
5 +24V TB6 (FG)
6 FG
TB7 24G
7 24G
Module TB8 Y0
power supply Load Surge suppressor TB9 COM B
8 Y0 TB10 Y1
9 COM B
TB11 COM B
10 Y1
11 COM B
TB12 Y2
12 Y2 TB13 COM B
13 COM B Triac TB14 Y3
14 Y3 TB15 COM B
15 COM B TB16 Y4
16 Y4 TB17 COM B
17 COM B
TB18 Y5
18 Y5
19 COM B
TB19 COM B
20 Y6 TB20 Y6
Load 21 COM B Surge suppressor TB21 COM B
22 Y7 TB22 Y7
23 COM B TB23 COM B
External load 24 COM A
TB24 COM A
power supply 25 COM B
TB25 COM B
100/200VAC
Triac

All COM B terminals are connected inside the module (shared common).

5 - 34 5 - 34
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

5.1.18 AJ65SBTB2N-16S triac output module

Type Triac output module
Item AJ65SBTB2N-16S Appearance
Number of output points 16 points
Isolation method Photocoupler
Rated load voltage 100 to 240VAC, 50/60Hz ±5%
Load voltage distortion ratio Within 5%
Max. load voltage 264VAC
Max. load current 0.6A/point, 4.8A/common
Min. load voltage/current 50VAC 100mA, 100VAC 10mA, 240VAC 10mA
Max. inrush current 25A, 10ms or less
1.5mArms or lower (at 100VACrms, 60Hz),
Leakage current at OFF
3mArms or lower (at 200VACrms, 60Hz)
Max. voltage drop at ON 1.5VACrms or lower (at 0.6A)

COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMBCOMB COMB
Y8 9 A B C D E F

COMA
OFF→ON 1ms or less
Response time

YF
ON→OFF Total of 1ms and 0.5 cycles or less
Surge suppressor CR absorber (0.01µF + 47Ω)

YE
Wiring method for common 16 points/common (2-wire, terminal block type)

PW L RUN L ERR. Y0 1 2 3 4 5 6 7

YD
Number of occupied stations 32-point assignment/station (16 points used)

YC
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

YB
Module power supply
Current 85mA or lower (at 24VDC and all points ON)

YA
Noise voltage: 1500Vp-p (AC type), 500Vp-p (DC type), noise width 1µs,

Y9
noise frequency 25 to 60Hz (noise simulator condition)
Noise immunity
Fast transient/burst immunity test

Y8
IEC 61000-4-4:1kV

Y7
2830VACrms for 3 cycles between all AC external terminals and ground (2000m

Y6
Withstand voltage above sea level)

Y5
500VAC for 1 minute between all DC external terminals and ground

Y4
10MΩ or higher between all AC external terminals and ground (500VDC insulation

Y3
resistance tester)
Insulation resistance
10MΩ or higher between all DC external terminals and ground (500VDC insulation
B RATE
40 20 10 8 4 2 1 4 2 1

Y2
resistance tester)

Y1
STATION NO.

Weight 0.35kg

Y0
7-point two-piece terminal block
Communication part, [Transmission circuit, module power supply, FG] (FG)
24G
ON
AJ65SBTB2N-16S

module power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
External
+24V

Applicable solderless terminal: 2 or less

SLD

connection
DG

34-point direct-mount terminal block

system
DB
DA

I/O power supply part, [I/O power supply, I/O signal]

I/O part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
M4 screw with plain washer finished round
Module mounting screw (tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

5 - 35 5 - 35
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
TB2 DB
1 DA
2 DB TB3 DG
3 DG Insulation TB4 SLD
4 SLD TB5 +24V
5 +24V TB6 (FG)
6 FG TB7 24G
7 24G
Module power supply TB8 Y0
Load Surge suppressor TB9 COM B
8 Y0 TB10 Y1
9 COM B TB11 COM B
10 Y1
TB12 Y2
11 COM B
12 Y2
TB13 COM B
13 COM B Triac TB14 Y3
14 Y3 TB15 COM B
15 COM B TB16 Y4
16 Y4 TB17 COM B
17 COM B
TB18 Y5
18 Y5
TB19 COM B
19 COM B
20 Y6 TB20 Y6
21 COM B TB21 COM B
22 Y7 TB22 Y7
23 COM B TB23 COM B
24 Y8 TB24 Y8
25 COM B
TB25 COM B
26 Y9
27 COM B
TB26 Y9
28 YA TB27 COM B
29 COM B TB28 YA
30 YB TB29 COM B
31 COM B TB30 YB
32 YC
TB31 COM B
33 COM B
34 YD
TB32 YC
35 COM B TB33 COM B
36 YE TB34 YD
Load
37 COM B Surge suppressor TB35 COM B
38 YF TB36 YE
39 COM B
TB37 COM B
40 COM A
External load power supply TB38 YF
41 COM B
TB39 COM B
100/200VAC
Triac TB40 COM A
TB41 COM B

All COM B terminals are connected inside the module (shared common).

5 - 36 5 - 36
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

5.1.19 AJ65DBTB1-32T1 transistor output module (sink type)

Type Transistor output module

Item AJ65DBTB1-32T1 Appearance
Number of output points 32 points
Isolation method Photocoupler
Rated load voltage 12/24VDC
Operating load voltage range 10.2 to 31.2VDC (ripple ratio: within 5%)
Max. load current 0.5A/point, 8A/common (2A/terminal)
Max. inrush current 1.2A, 10ms or less
Leakage current at OFF 0.1mA or lower
Max. voltage drop at ON 0.3VDC or lower (TYP.) 0.5A, 0.6VDC or lower (MAX.) 0.5A
Output type Sink type
Protection function None
OFF→ON 0.5ms or less
Response time
ON→OFF 1.5ms or less (resistive load)
External power supply for Voltage 10.2 to 31.2VDC (ripple ratio: within 5%)
output part Current 50mA or lower (at 24VDC and all points ON), excluding external load current
Surge suppressor Zener diode
Wiring method for common 32 points/common (4 points) (1-wire, terminal block type)
Number of occupied stations 32-point assignment/station (32 points used)
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
Module power supply
Current 65mA or lower (at 24VDC and all points ON)
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity
noise frequency 25 to 60Hz (DC type noise simulator condition)
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
10MΩ or higher between all DC external terminals and ground (500VDC
Insulation resistance
insulation resistance tester)
Protection degree IP2X
Weight 0.7kg
50-point terminal block
[Transmission circuit, module power supply, FG, I/O power supply, I/O signal]
External connection system
M3×7 screw (tightening torque range: 0.68 to 0.92N•m)
Applicable solderless terminal: 2 or less
M4 screw with plain washer finished round
Module mounting screw
(tightening torque range: 0.78 to 1.08N•m)
Applicable solderless terminal R1.25-3.5, RAV2-3.5 (compliant with JIS C 2805)
Accessory User’s manual
Part sold separately A6DIN1C, A2CCOM-TB

5 - 37 5 - 37
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection
Terminal Signal Terminal Signal
number name number name
TB1 DA TB26 Empty
TB2 DG Insulation
TB27 Empty
TB3 DB 1 DA Empty 26 TB28 +24V
2 DG Empty 27
TB4 Empty TB29 CTL+
3 DB +24V 28 24VDC
TB5 SLD 4 Empty CTL+ 29 TB30 (FG)
5 SLD FG 30
TB6 Empty 6 Empty
Constant-voltage circuit
CTLG 31
TB31 CTLG
TB7 24G 7 24G 24G 32 Module TB32 24G
power supply
TB8 Y0 TB33 Y10
TB9 Y1 TB34 Y11
TB10 Y2 Load Load TB35 Y12
8 Y0 Y10 33
TB11 Y3 9 Y1 Y11 34 TB36 Y13
10 Y2 Y12 35
TB12 Y4 11 Y3 Y13 36
TB37 Y14
TB13 Y5 12 Y4 Y14 37 TB38 Y15
13 Y5 Y15 38
TB14 Y6 14 Y6 Y16 39 TB39 Y16
Load Load
TB15 Y7 15 Y7 Y17 40 TB40 Y17
Load 16 COM1 COM3 41 Load
TB16 COM1 17 Y8 Y18 42 TB41 COM3
TB17 Y8 18 Y9 Y19 43 TB42 Y18
19 YA Y1A 44
TB18 Y9 20 YB Y1B 45 TB43 Y19
21 YC Y1C 46
TB19 YA YD Y1D 47
TB44 Y1A
22
TB20 YB Load 23 YE Y1E 48 Load TB45 Y1B
24 YF Y1F 49
TB21 YC 25 COM2 COM4 50
TB46 Y1C
TB22 YD TB47 Y1D
TB23 YE TB48 Y1E
TB24 YF TB49 Y1F
TB25 COM2 TB50 COM4

5 - 38 5 - 38
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

5.1.20 AJ65DBTB1-32R contact output module

Type Contact output module

Item AJ65DBTB1-32R Appearance
Number of output points 32 points
Isolation method Photocoupler
2A/point, 4A/common (2A/terminal)
Rated load voltage/current
at 24VDC (resistive load) or 240VAC (cosφ=1)
Min. switching load 5VDC, 1mA
Max. switching voltage 264VAC, 125VDC
OFF→ON 10ms or less
Response time
ON→OFF 12ms or less
Mechanical 20 million times or more
Rated switching voltage/current load: 100 thousand times or more
Life 200VAC 1.5A, 240VAC 1A (cosφ=0.7): 100 thousand times or more
Electrical AJ65DBTB1- 32R
200VAC 1A, 240VAC 0.5A (cosφ=0.35): 100 thousand times or more 5
6

4 1
0 ~0
1
PW L RUN
0 8 10
L ERR.
18
3 2

24VDC 1A, 100VDC 0.1A (L/R=7ms): 100 thousand times or more 1 9 11

STATI ON NO. 19
7 8 2 A 12 1A
6 9
5 0 ~
1 3 B 13 1B

Max. switching frequency 3600 times/hour

4 1
3 2 4 C 14 1C
5 D 15 1D
6 E 16 1E
B RATE
Surge suppressor None
0
4 1 7 F 17 1F
3 2

External power supply for Voltage 24VDC ±10% (ripple ratio: 4Vp-p or lower)
output part DA NC

(CTL+ and CTLG terminals) Current 180mA or lower (at 24VDC and all points ON) DG NC
DB +24V

Wiring method for common 8 points/common (1-wire, terminal block type) NC

SLD
CTL+

( FG)
Number of occupied stations 32-point assignment/station (32 points used) NC
24G 24G
CTLG

Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

Module power supply Y0 Y10

Current 80mA or lower (at 24VDC and all points ON) Y1 Y11
Y2 Y12

Noise voltage: 1500Vp-p (AC type), 500Vp-p (DC type), noise width 1µs, Y3 Y13

Noise immunity Y4 Y14

noise frequency 25 to 60Hz (noise simulator condition) Y5 Y15
Y6 Y16
1500VAC for 1 minute between all AC external terminals and ground Y7 Y17
Withstand voltage COM1 COM3
500VAC for 1 minute between all DC external terminals and ground Y8 Y18
Y9 Y19
10MΩ or higher between all AC external terminals and ground (500VDC YA Y1A

insulation resistance tester) YB Y1B

Insulation resistance YC Y1C

10MΩ or higher between all DC external terminals and ground (500VDC YD Y1D
YE Y1E
insulation resistance tester) YF Y1F
COM4
COM2
Protection degree IP1X AJ65DBTB1
- 32R

Weight 0.7kg
50-point terminal block
[Transmission circuit, module power supply, FG,
External connection system I/O power supply, I/O signal]
M3.5×7 screw (tightening torque range: 0.68 to 0.92N•m)
Applicable solderless terminal: 2 or less
M4 screw with plain washer finished round
Module mounting screw
(tightening torque range: 0.78 to 1.08N•m)
Applicable solderless terminal R1.25-3.5, RAV2-3.5 (compliant with JIS C 2805)
Accessory User’s manual
Part sold separately A6DIN1C, A2CCOM-TB

5 - 39 5 - 39
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection
Terminal Signal Terminal Signal
number name number name
TB1 DA TB26 Empty
TB2 DG TB27 Empty
TB3 DB TB28 +24V
TB4 Empty 1 DA
Insulation
Empty 26 TB29 CTL+
TB5 SLD 2 DG Empty 27 24VDC TB30 (FG)
3 DB CTL+ +24V 28
TB6 Empty 4 Empty CTL+ 29 TB31 CTLG
5 SLD FG 30
TB7 24G 6 Empty CTLG CTLG 31
TB32 24G
TB8 Y0 7 24G 24G 32 TB33 Y10
Module power supply
TB9 Y1 TB34 Y11
Load Load
TB10 Y2 8 Y0 CTL+ CTL+ Y10 33 TB35 Y12
9 Y1 Y11 34
TB11 Y3 10 Y2 Y12 35
TB36 Y13
TB12 Y4 11 Y3 Y13 36 TB37 Y14
12 Y4 Y14 37
TB13 Y5 13 Y5 Y15 38 TB38 Y15
TB14 Y6 Load 14 Y6 Y16 39 Load TB39 Y16
15 Y7 Y17 40
TB15 Y7 Load 16 COM1
CTLG CTLG
COM3 41 Load
TB40 Y17
17 Y8 Y18 42
TB16 COM1 CTL+ CTL+ TB41 COM3
18 Y9 Y19 43
TB17 Y8 19 YA Y1A 44 TB42 Y18
20 YB Y1B 45
TB18 Y9 21 YC Y1C 46
TB43 Y19
TB19 YA 22 YD Y1D 47 TB44 Y1A
Load 23 YE Y1E 48 Load
TB20 YB 24 YF Y1F 49 TB45 Y1B
CTLG CTLG
25 COM2 COM4 50
TB21 YC TB46 Y1C
TB22 YD TB47 Y1D
TB23 YE TB48 Y1E
TB24 YF TB49 Y1F
TB25 COM2 TB50 COM4

5 - 40 5 - 40
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

5.2 Spring Clamp Terminal Block Type Output Module

5.2.1 AJ65VBTS2-16T transistor output module (sink type)

Type Transistor output module

Item AJ65VBTS2-16T Appearance
Number of output points 16 points
Isolation method Photocoupler
Rated load voltage 12/24VDC
Operating load voltage range 10.2 to 26.4VDC (ripple ratio: within 5%)
Max. load current 0.5A/point, 4A/common
Max. inrush current 1.0A, 10ms or less
Leakage current at OFF 0.1mA or lower
Max. voltage drop at ON 0.3VDC or lower (TYP.) 0.5A, 0.6VDC or lower (MAX.) 0.5A
Output type Sink type
Protection function None
OFF→ON 1ms or less
Response time
ON→OFF 1ms or less (resistive load)
External power Voltage 10.2 to 26.4VDC (ripple ratio: within 5%)
supply for output part

YF
Current 30mA or lower (at 24VDC and all points ON), excluding external load current

YC YD YE
Surge suppressor Zener diode
Wiring method for common 16 points/common (2-wire, spring clamp terminal block type)
Number of occupied stations 32-point assignment/station (16 points used)

YA YB
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
supply Current 45mA or lower (at 24VDC and all points ON)

Y9
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity

COM+
Y8
noise frequency 25 to 60Hz (DC type noise simulator condition)

NC
Y7
AJ65VBTS2-16T
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

Y6
10MΩ or higher between all DC external terminals and ground (500VDC
Insulation resistance

Y5
insulation resistance tester)

Y4
Protection degree IP1XB

Y2 Y3
Weight 0.24kg
One-touch connector for communication [Transmission circuit] Y1

5-pin IDC plug is sold separately: A6CON-L5P

Y0

Communication part
<Optional>
COM+

COM-
NC

External Online connector for communication: A6CON-LJ5P

connection One-touch connector for power supply and FG [Module power supply, FG]
system 5-pin IDC plug is sold separately: A6CON-PW5P, A6CON-PW5P-SOD
D
8 9 A B C D E F
0 1 2 3 4 5 6 7

Power supply part

<Optional>
L RUN L ERR.

Online connector for power supply: A6CON-PWJ5P

I/O part 2-piece spring clamp terminal block [I/O power supply, I/O signals]
ONPW

Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715) B RATE STATION NO.
1 2 4 1 2 4 8 1020 40

Connector for Applicable cable:

CON A

communication FANC-110SBH, FA-CBL200PSBH, CS-110

0.66 to 0.98mm2 (AWG18)
Connector for power [φ2.2 to 3.0mm (A6CON-PW5P), φ2.0 to 2.3mm (A6CON-PW5P-SOD)]
supply and FG Wire diameter: 0.16mm or more
Insulating coating material: PVC (heat-resistant)
Applicable Spring clamp terminal Stranded wire 0.08 to 1.5mm2 (AWG28 to 16) 1
wire size block for I/O Wire strip length: 8 to 11mm
TE0.5 [Applicable wire size: 0.5mm2]
TE0.75 [Applicable wire size: 0.75mm2]
2
Applicable TE1 [Applicable wire size: 0.9 to 1.0mm ]
solderless terminal TE1.5 [Applicable wire size: 1.25 to 1.5mm2]
FA-VTC125T9 [Applicable wire size: 0.3 to 1.65mm2]
2
FA-VTCW125T9 [Applicable wire size: 0.3 to 1.65mm ]
Accessory User’s manual, Holding fixtures for screw installation

1: Insert one wire per terminal.

5 - 41 5 - 41
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection

CONA
1
1
Pin number Signal name
DA
LINK CABLE 2
(IN) 3
2 DB 1 DA
3 DG
4
5
4 Empty 2 DB
5 SLD
CONB
CON A, B 3 DG
1
LINK CABLE 2
1 DA
4 Empty
2 DB
(OUT) 3
4
3 DG 5 SLD
4 Empty
5
5 SLD 1 (FG)
One-touch connector for communication
CONC
2 +24V (UNIT)
1 Insulation
UNIT POWER CABLE(IN)
2
1 FG CON C, D 3 24G (UNIT)
2 +24V(UNIT)
3
4
3 24G(UNIT) 4 Empty
4 Empty
5
5 Empty 5 Empty
COND
UNIT POWER CABLE(OUT) 1
1 FG
Terminal block
2
3
2 +24V(UNIT)
Column A Column B Column C
3 24G(UNIT)
4
5
4 Empty 1 Empty 1 COM+ 1 COM-
5 Empty
One-touch connector for power supply and FG 1
2 Y0 2 COM+ 2 Empty
Constant-voltage circuit
TB1A Empty 3 Y1 3 COM+ 3 Empty
External power supply for output part TB1B COM+
Load
TB1C COM- 4 Y2 4 COM+ 4 Empty
TB2A Y0
TB2B COM+ 5 Y3 5 COM+ 5 Empty
TB2C Empty
TB3A Y1
6 Y4 6 COM+ 6 Empty
TB3B COM+
7 Y5 7 COM+ 7 Empty
TB3C Empty
TB4A Y2 8 Y6 8 COM+ 8 Empty
TB4B COM+
TB4C Empty 9 Y7 9 COM+ 9 Empty
TB5A Y3
TB5B COM+ 10 Y8 10 COM+ 10 Empty
TB5C Empty
TB6A Y4 11 Y9 11 COM+ 11 Empty
TB6B COM+
TB6C Empty
12 YA 12 COM+ 12 Empty
TB7A Y5
13 YB 13 COM+ 13 Empty
TB7B COM+
TB7C Empty 14 YC 14 COM+ 14 Empty
TB8A Y6
TB8B COM+ 15 YD 15 COM+ 15 Empty
TB8C Empty
TB9A Y7 16 YE 16 COM+ 16 Empty
TB9B COM+
TB9C Empty 17 YF 17 COM+ 17 Empty
TB10A Y8
TB10B COM+
TB10C Empty
TB11A Y9
TB11B COM+
TB11C Empty
TB12A YA
TB12B COM+
TB12C Empty
TB13A YB
TB13B COM+
TB13C Empty
TB14A YC
TB14B COM+
TB14C Empty
TB15A YD
TB15B COM+
TB15C Empty
TB16A YE
TB16B COM+
Load TB16C Empty
TB17A YF
TB17B COM+
TB17C Empty

1: Attach an unwired connector plug to an unused one-touch connector for power supply and FG.

5 - 42 5 - 42
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection

<When using online connectors>

Online connector
for communication
CONA
1
1 DA
LINK CABLE 2
(IN) 2 DB
3
3 DG
4
4 Empty
5
5 SLD
CONB
1
1 DA
LINK CABLE 2
(OUT) 2 DB
3
3 DG
4
4 Empty
5
5 SLD
One-touch connector
for communication
CONC
UNIT POWER CABLE(IN) 1
1 FG
2
2 +24V(UNIT)
3
3 24G(UNIT)
4
4 Empty
5
5 Empty
COND
1
1 FG
2
UNIT POWER 2 +24V(UNIT)
CABLE(OUT) 3
3 24G(UNIT)
4
4 Empty
5 Empty
5

One-touch connector for power

Online connector
supply and FG *1
for power supply
and FG

1: Attach an unwired connector plug to an unused one-touch connector for power supply and FG.
Pin layout

Viewed from the front of the module

5 - 43 5 - 43
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

5.2.2 AJ65VBTS2-32T transistor output module (sink type)

Type Transistor output module

Item AJ65VBTS2-32T Appearance
Number of output points 32 points
Isolation method Photocoupler
Rated load voltage 12/24VDC
Operating load voltage range 10.2 to 26.4VDC (ripple ratio: within 5%)
Max. load current 0.5A/point, 4A/common
Max. inrush current 1.0A, 10ms or less
Leakage current at OFF 0.1mA or lower
Max. voltage drop at ON 0.3VDC or lower (TYP.) 0.5A, 0.6VDC or lower (MAX.) 0.5A
Output type Sink type

NC Y10 Y11 Y12 Y13 Y14 Y15 Y16 Y17 Y18 Y19 Y1A Y1B Y1C Y1D Y1E Y1F
Protection function None
OFF→ON 1ms or less
Response time
ON→OFF 1ms or less (resistive load)
External power Voltage 10.2 to 26.4VDC (ripple ratio: within 5%)
supply for output part Current 30mA or lower (at 24VDC and all points ON), excluding external load current

COM2+
Surge suppressor Zener diode

NC
Wiring method for common 16 points/common (2-wire, spring clamp terminal block type)
Number of occupied stations 32-point assignment/station (32 points used)
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
Module power supply
Current 60mA or lower (at 24VDC and all points ON)
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity
noise frequency 25 to 60Hz (DC type noise simulator condition)

AJ65VBTS2-32T

COM2+

COM2-
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

YA YB YC YD YE YF
10MΩ or higher between all DC external terminals and ground (500VDC insulation
Insulation resistance
resistance tester)
Protection degree IP1XB
Weight 0.40kg
One-touch connector for communication [Transmission circuit]

Y9
Communication 5-pin IDC plug is sold separately: A6CON-L5P

COM1+
Y8

NC
part <Optional>

Y7
External Online connector for communication: A6CON-LJ5P
Y6
Y5
connection One-touch connector for power supply and FG [Module power supply, FG] Y4

system 5-pin IDC plug is sold separately: A6CON-PW5P, A6CON-PW5P-SOD

Y3

Power supply part

<Optional>
Y2

Online connector for power supply: A6CON-PWJ5P

Y1
Y0

I/O part 2-piece spring clamp terminal block [I/O power supply, I/O signals]
COM1+

COM1-
NC

Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)

Connector for Applicable cable:
D
8 9 A B CD E F

communication FANC-110SBH, FA-CBL200PSBH, CS-110

0 1 2 3 4 5 6 7
L ERR.

2
0.66 to 0.98mm (AWG18)
C
PW L RUN

Connector for power [φ2.2 to 3.0mm (A6CON-PW5P), φ2.0 to 2.3mm (A6CON-PW5P-SOD)]

B
ON

supply and FG Wire diameter: 0.16mm or more

B RATESTATION NO.
1 2 4 1 2 4 8 102040

Insulating coating material: PVC (heat-resistant)

CON A

Applicable Spring clamp Stranded wire 0.08 to 1.5mm2 (AWG28 to 16) 1

wire size terminal block for I/O Wire strip length: 8 to 11mm
2
TE0.5 [Applicable wire size: 0.5mm ]
TE0.75 [Applicable wire size: 0.75mm2]
Applicable
TE1 [Applicable wire size: 0.9 to 1.0mm2]
solderless 2
TE1.5 [Applicable wire size: 1.25 to 1.5mm ]
terminal
FA-VTC125T9 [Applicable wire size: 0.3 to 1.65mm2]
FA-VTCW125T9 [Applicable wire size: 0.3 to 1.65mm2]
Accessory User’s manual, Holding fixtures for screw installation

1: Insert one wire per terminal.

5 - 44 5 - 44
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection

Pin number Signal name

1 DA
CONA
1
2
1 DA 2 DB
LINK CABLE 2 DB
(IN) 3
3 DG CON A, B 3 DG
4
4 Empty
5
5 SLD 4 Empty
1
CONB 5 SLD
1 DA
LINK CABLE 2
(OUT) 3
2 DB 1 (FG)
3 DG
4
5
4 Empty 2 +24V (UNIT)
5 SLD
CON C, D 3 24G (UNIT)
One-touch connector for communication
CONC
UNIT POWER CABLE(IN)
1
1 FG
Insulation 4 Empty
2
3
2 +24V(UNIT)
5 Empty
3 24G(UNIT)
4
5
4 Empty Terminal block
5 Empty

COND Column A Column B Column C

1
UNIT POWER CABLE(OUT) 1 FG
2
2 +24V(UNIT) 1 Empty 1 COM1+ 1 COM1-
3
24G(UNIT)
4
3
4 Empty
2 Y0 2 COM1+ 2 Empty
5

1
5 Empty
3 Y1 3 COM1+ 3 Empty
One-touch connector for power supply and FG
TB1A Empty 4 Y2 4 COM1+ 4 Empty
External power supply TB1B COM1+
for output part Load
TB1C COM1- Constant-voltage circuit 5 Y3 5 COM1+ 5 Empty
TB2A Y0
TB2B COM1+ 6 Y4 6 COM1+ 6 Empty
TB2C Empty
TB3A Y1 7 Y5 7 COM1+ 7 Empty
TB3B COM1+
TB3C Empty 8 Y6 8 COM1+ 8 Empty
TB4A Y2
TB4B COM1+
9 Y7 9 COM1+ 9 Empty
Empty
TB4C
10 Y8 10 COM1+ 10 Empty
11 Y9 11 COM1+ 11 Empty
12 YA 12 COM1+ 12 Empty
13 YB 13 COM1+ 13 Empty
TB15A YD
14 YC 14 COM1+ 14 Empty
TB15B COM1+
TB15C Empty
15 YD 15 COM1+ 15 Empty
TB16A YE 16 YE 16 COM1+ 16 Empty
TB16B COM1+
Load
TB16C Empty 17 YF 17 COM1+ 17 Empty
TB17A YF
TB17B COM1+ 18 Empty 18 COM2+ 18 COM2-
TB17C Empty
TB18A Empty 19 Y10 19 COM2+ 19 Empty
External power supply TB18B COM2+
for output part Load
TB18C COM2- Constant-voltage circuit
20 Y11 20 COM2+ 20 Empty
TB19A Y10
TB19B COM2+
21 Y12 21 COM2+ 21 Empty
TB19C Empty
TB20A Y11
22 Y13 22 COM2+ 22 Empty
TB20B COM2+
TB20C Empty
23 Y14 23 COM2+ 23 Empty
TB21A Y12
24 Y15 24 COM2+ 24 Empty
TB21B COM2+
TB21C Empty 25 Y16 25 COM2+ 25 Empty
26 Y17 26 COM2+ 26 Empty
27 Y18 27 COM2+ 27 Empty
28 Y19 28 COM2+ 28 Empty
TB32A Y1D 29 Y1A 29 COM2+ 29 Empty
TB32B COM2+
TB32C Empty 30 Y1B 30 COM2+ 30 Empty
TB33A Y1E
TB33B COM2+
31 Y1C 31 COM2+ 31 Empty
Load
TB33C Empty
TB34A Y1F
32 Y1D 32 COM2+ 32 Empty
TB34B COM2+
33 Y1E 33 COM2+ 33 Empty
TB34C Empty
34 Y1F 34 COM2+ 34 Empty
1: Attach an unwired connector plug to an unused one-
touch connector for power supply and FG.

5 - 45 5 - 45
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection

<When using online connectors>

Online connector
for communication
CONA
1
1 DA
LINK CABLE 2
(IN) 2 DB
3
3 DG
4
4 Empty
5
5 SLD
CONB
1
1 DA
LINK CABLE 2
(OUT) 2 DB
3
3 DG
4
4 Empty
5
5 SLD
One-touch connector
for communication
CONC
UNIT POWER CABLE(IN) 1
1 FG
2
2 +24V(UNIT)
3
3 24G(UNIT)
4
4 Empty
5
5 Empty
COND
1
1 FG
2
UNIT POWER 2 +24V(UNIT)
CABLE(OUT) 3
3 24G(UNIT)
4
4 Empty
5 Empty
5

One-touch connector for power

Online connector
supply and FG *1
for power supply
and FG

1: Attach an unwired connector plug to an unused one-touch connector for power supply and FG.

Pin layout

Viewed from the front of the module

5 - 46 5 - 46
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

5.3 Sensor Connector (e-CON) Type Output Module

5.3.1 AJ65VBTCE2-8T transistor output module (sink type)

Type Transistor output module

Item AJ65VBTCE2-8T Appearance
Number of output points 8 points
Isolation method Photocoupler
Rated load voltage 12/24VDC
Operating load voltage range 10.2 to 26.4VDC (ripple ratio: within 5%)
Max. load current 0.1A/point, 0.8A/common
Max. inrush current 0.7A, 10ms or less
Leakage current at OFF 0.1mA or lower
Max. voltage drop at ON 0.1VDC or lower (TYP.) 0.1A, 0.2VDC or lower (MAX.) 0.1A
Output type Sink type
Protection function Overload protection, overvoltage protection, overheat protection
OFF→ON 1ms or less
Response time
ON→OFF 1ms or less (resistive load)
External power Voltage 10.2 to 26.4VDC (ripple ratio: within 5%) CON ON
supply for output 1
2
A
part Current 5mA or lower (at 24VDC and all points ON), excluding external load current 3
4
5
6
Surge suppressor Zener diode 7
8
9
B 10
Wiring method for common 8 points/common (2-wire, sensor connector (e-CON) type)
40 S
Number of occupied stations 32-point assignment/station (8 points used) 20
T
A
C 10 T
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%) 8
I
O
4 N
supply Current 35mA or lower (at 24VDC and all points ON) 2 N
1 O.
D B
Noise voltage 500Vp-p, noise width 1µs, 4 R
Noise immunity 2
1
A
T
noise frequency 25 to 60Hz (DC type noise simulator condition) E

Withstand voltage 500VAC for 1 minute between all DC external terminals and ground A J65VBTCE2-8T
PW
10MΩ or higher between all DC external terminals and ground (500VDC insulation Y0
L RUN
Insulation resistance
resistance tester) L ERR.
Y1
Protection degree IP1XB 0
1
Weight 0.10kg Y2
2
One-touch connector for communication [Transmission circuit] 3
Y3 4
Communication 5-pin IDC plug is sold separately: A6CON-L5P 5
6
part <Optional> Y4 7
Online connector for communication: A6CON-LJ5P
Y5
External One-touch connector for power supply and FG
connection [Module power supply, I/O power supply, FG] Y6
Power supply
system 5-pin IDC plug is sold separately: A6CON-PW5P, A6CON-PW5P-SOD
part Y7
<Optional>
Online connector for power supply: A6CON-PWJ5P
Sensor connector (e-CON) [I/O signals]
I/O part
4-pin IDC plug is sold separately. 1
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Connector for Applicable cable:
communication FANC-110SBH, FA-CBL200PSBH, CS-110
2
0.66 to 0.98mm (AWG18)
Connector for
[φ2.2 to 3.0mm (A6CON-PW5P), φ2.0 to 2.3mm (A6CON-PW5P-SOD)]
Applicable power supply and
Wire diameter: 0.16mm or more
wire size FG
Insulating coating material: PVC (heat-resistant)
Sensor connector (e-CON).
Connector for I/O Applicable connector plugs are sold separately. 1
(applicable wire size: 0.08 to 0.5mm2, depending on the connector plug)
Accessory User’s manual, Holding fixtures for screw installation

1: Refer to Section 1.6.2 for details.

5 - 47 5 - 47
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection

<When using online connectors>

Pin number Signal name
1 DA
2 DB
CON A,B 3 DG
4 Empty
5 SLD
1 (FG)
2 +24V (UNIT)
1
CONA CON C,D 3 24G (UNIT)
1 DA
LINK CABLE 2
2 DB 4 +24V (I/O)
(IN) 3
3 DG
4
4 Empty 5 24G (I/O)
5
5 SLD
Pin Signal
CONB Pin layout
1
1 DA number name
LINK CABLE 2
2 DB
(OUT) 3
3 DG
1 +24V
4
5
4 Empty CON1 2 Empty
5 SLD
One-touch connector for communication
(Y0) 3 Empty
1
CONC Insulation 4 Y0
UNIT POWER CABLE(IN) 1 FG
2
3
2 +24V(UNIT) 1 +24V
3 24G(UNIT)
4
4 +24V(I/O) CON2 2 Empty
5
5 24G(I/O)
I/O POWER CABLE(IN)
(Y1) 3 Empty
COND
UNIT POWER CABLE(OUT)
1
1 FG 4 Y1
2
2 +24V(UNIT)
3
3 24G(UNIT) 1 +24V
4
4 +24V(I/O)
5
5 24G(I/O)
CON3 2 Empty
I/O POWER CABLE(OUT) (Y2) 3 Empty
1
One-touch connector for power supply and FG
2 CON1 4 Y2
1 Constant-voltage circuit
2 1 +24V
3
Load
4
CON4 2 Empty
(Y3) 3 Empty
4 Y3
1 +24V
CON8 CON5 2 Empty
1
2
(Y4) 3 Empty
3
Load 4 Y4
4
1 +24V
CON6 2 Empty
Viewed from the
(Y5) 3 Empty
front of the module
4 Y5
1 +24V
CON7 2 Empty
(Y6) 3 Empty
4 Y6
1 +24V
CON8 2 Empty
(Y7) 3 Empty
1: Attach an unwired connector plug to an unused one-touch connector for power supply and 4 Y7
FG.
2: Wiring the sensor connector (e-CON) incorrectly may cause malfunction or failure due to short
circuit of the power supply.

5 - 48 5 - 48
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection

<When using online connectors>

Online connector
for communication
CONA
1
1 DA
LINK CABLE 2
(IN) 2 DB
3
3 DG
4
4
5
5 SLD
CONB
1
1 DA
LINK CABLE 2
(OUT) 2 DB
3
3 DG
4
4
5
5 SLD
One-touch connector
for communication
CONC
1
UNIT POWER CABLE(IN) 1 FG
2
2 +24V(UNIT)
3
3 24G(UNIT)
4
4 +24V(I/O)
5
5 24G(I/O)
I/O POWER CABLE(IN) COND
1
1 FG
2
UNIT POWER 2 +24V(UNIT)
CABLE(OUT) 3
3 24G(UNIT)
4
I/O POWER 4 +24V(I/O)
CABLE(OUT) 5
5 24G(I/O)

One-touch connector for power

supply and FG *1 Online connector
for power supply
and FG

1: Attach an unwired connector plug to an unused one-touch connector for power supply and FG.

5 - 49 5 - 49
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

5.3.2 AJ65VBTCE2-16T transistor output module (sink type)

Type Transistor output module

Item AJ65VBTCE2-16T Appearance
Number of output points 16 points
Isolation method Photocoupler
Rated load voltage 12/24VDC
Operating load voltage range 10.2 to 26.4VDC (ripple ratio: within 5%)
Max. load current 0.1A/point, 1.6A/common
Max. inrush current 0.7A, 10ms or less
Leakage current at OFF 0.1mA or lower
Max. voltage drop at ON 0.1VDC or lower (TYP.) 0.1A, 0.2VDC or lower (MAX.) 0.1A
Output type Sink type
Protection function Overload protection, overvoltage protection, overheat protection
OFF→ON 1ms or less
Response time
ON→OFF 1ms or less (resistive load)
External power Voltage 10.2 to 26.4VDC (ripple ratio: within 5%)
supply for output
part Current 10mA or lower (at 24VDC and all points ON), excluding external load current
Surge suppressor Zener diode

F
7
Wiring method for common 16 points/common (2-wire, sensor connector (e-CON) type)

AJ65VBTCE2-16T

E
6
Number of occupied stations 32-point assignment/station (16 points used)

D
5
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
supply Current 45mA or lower (at 24VDC and all points ON)

C
4
Noise voltage 500Vp-p, noise width 1µs,

B
3
Noise immunity
noise frequency 25 to 60Hz (DC type noise simulator condition)

A
2
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

9
10MΩ or higher between all DC external terminals and ground (500VDC insulation
Insulation resistance
resistance tester)

8
Y

Y
Protection degree IP1XB
Weight 0.10kg

D
8 9 A B C D E F
0 1 2 3 4 5 6 7
One-touch connector for communication [Transmission circuit]
PW L RUNL ERR.

Communication 5-pin IDC plug is sold separately: A6CON-L5P

C
part <Optional>
Online connector for communication: A6CON-LJ5P

B
ON

B RATE STATION NO.

External One-touch connector for power supply and FG 1 2 4 1 2 4 8 102040

connection [Module power supply, I/O power supply, FG]

CON A
Power supply
system 5-pin IDC plug is sold separately: A6CON-PW5P, A6CON-PW5P-SOD
part
<Optional>
Online connector for power supply: A6CON-PWJ5P
Sensor connector (e-CON) [I/O signals]
I/O part
4-pin IDC plug is sold separately. 1
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Connector for Applicable cable:
communication FANC-110SBH, FA-CBL200PSBH, CS-110
0.66 to 0.98mm2 (AWG18)
Connector for
[φ2.2 to 3.0mm (A6CON-PW5P), φ2.0 to 2.3mm (A6CON-PW5P-SOD)]
Applicable power supply and
Wire diameter: 0.16mm or more
wire size FG
Insulating coating material: PVC (heat-resistant)
Sensor connector (e-CON).
Connector for
Applicable connector plugs are sold separately. 1
I/O
(applicable wire size: 0.08 to 0.5mm2, depending on the connector plug)
Accessory User’s manual, Holding fixtures for screw installation

1: Refer to Section 1.6.2 for details.

5 - 50 5 - 50
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection

Pin number Signal name

1 DA
2 DB
CON A, B 3 DG
CONA
1
1 DA 4 Empty
LINK CABLE 2
2 DB
(IN) 3
3 DG
5 SLD
4
5
4 Empty 1 (FG)
5 SLD
CONB
2 +24V (UNIT)
1
1 DA CON C, D 3 24G (UNIT)
LINK CABLE 2
2 DB
(OUT) 3
3 DG 4 +24V (I/O)
4
5
4 Empty 5 24G (I/O)
5 SLD
One-touch connector for communication Pin number Signal name Pin number Signal name
1
CONC Insulation 1 +24V 1 +24V
UNIT POWER CABLE(IN) 1 FG
2
2 +24V(UNIT) CON1 2 Empty 1 CON9 2 Empty 1
3
4
3 24G(UNIT) (Y0) 3 Empty 2 (Y8) 3 Empty 2
4 +24V(I/O)
5
5 24G(I/O) 4 Y0 4 Y8
I/O POWER CABLE(IN)
1
COND 1 +24V 1 +24V
UNIT POWER CABLE(OUT) 1 FG
2
2 +24V(UNIT) CON2 2 Empty 1 CON10 2 Empty 1
3
3 24G(UNIT)
4 (Y1) 3 Empty 2 (Y9) 3 Empty 2
4 +24V(I/O)
5
5 24G(I/O) 4 Y1 4 Y9
I/O POWER CABLE(OUT)
One-touch connector for power supply and FG 3 1 +24V 1 +24V
4 CON1
1 Constant-voltage circuit CON3 2 Empty 1 CON11 2 Empty 1
2 (Y2) 3 Empty 2 (YA) 3 Empty 2
3
Load 4 4 Y2 4 YA
1 +24V 1 +24V
CON4 2 Empty 1 CON12 2 Empty 1
2 1 (Y3) 3 Empty 2 (YB) 3 Empty 2
CON16 4 Y3 4 YB
1 1 +24V 1 +24V
2
3 CON5 2 Empty 1 CON13 2 Empty 1
Load 4
(Y4) 3 Empty 2 (YC) 3 Empty 2
4 Y4 4 YC
1 +24V 1 +24V
CON6 2 Empty 1 CON14 2 Empty 1
(Y5) 3 Empty 2 (YD) 3 Empty 2
4 Y5 4 YD
1 +24V 1 +24V
CON7 2 Empty 1 CON15 2 Empty 1
(Y6) 3 Empty 2 (YE) 3 Empty 2
1: Since all No.2 pins of CON1 to CON16 are connected inside the module, they cannot be
4 Y6 4 YE
used.
1 +24V 1 +24V
2: Since all No.3 pins of CON1 to CON16 are connected inside the module, they cannot be
CON8 2 Empty 1 CON16 2 Empty 1
used. (Y7) 3 Empty 2 (YF) 3 Empty 2
3: Attach an unwired connector plug to an unused one-touch connector for power supply and 4 Y7 4 YF
FG.
4: Wiring the sensor connector (e-CON) incorrectly may cause malfunction or failure due to
short circuit of the power supply.

5 - 51 5 - 51
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection

<When using online connectors>

Online connector
for communication
CONA
1
1 DA
LINK CABLE 2
(IN) 2 DB
3
3 DG
4
4
5
5 SLD
CONB
1
1 DA
LINK CABLE 2
(OUT) 2 DB
3
3 DG
4
4
5
5 SLD
One-touch connector
for communication
CONC
1
UNIT POWER CABLE(IN) 1 FG
2
2 +24V(UNIT)
3
3 24G(UNIT)
4
4 +24V(I/O)
5
5 24G(I/O)
I/O POWER CABLE(IN) COND
1
1 FG
2
UNIT POWER 2 +24V(UNIT)
CABLE(OUT) 3
3 24G(UNIT)
4
I/O POWER 4 +24V(I/O)
CABLE(OUT) 5
5 24G(I/O)

One-touch connector for power

supply and FG *1 Online connector
for power supply
and FG

1: Attach an unwired connector plug to an unused one-touch connector for power supply and FG.

Pin layout

Viewed from the front of the module

5 - 52 5 - 52
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

5.3.3 AJ65VBTCE3-16TE transistor output module (source type)

Type Transistor output module

Item AJ65VBTCE3-16TE Appearance
Number of output points 16 points
Isolation method Photocoupler
Rated load voltage 12/24VDC
Operating load voltage range 10.2 to 26.4VDC (ripple ratio: within 5%)
Max. load current 0.1A/point, 1.6A/common
Max. inrush current 0.7A, 10ms or less
Leakage current at OFF 0.1mA or lower
Max. voltage drop at ON 0.1VDC or lower (TYP.) 0.1A, 0.2VDC or lower (MAX.) 0.1A
Output type Source type
Protection function Overload protection, overheat protection
OFF→ON 1ms or less
Response time
ON→OFF 1ms or less (resistive load)
External power Voltage 10.2 to 26.4VDC (ripple ratio: within 5%)
supply for output
part Current 11mA or lower (at 24VDC and all points ON), excluding external load current
Surge suppressor Zener diode
Supply current for connected
1.0A or lower/common
device
Wiring method for common 16 points/common (3-wire, sensor connector (e-CON) type)
Number of occupied stations 32-point assignment/station (16 points used)
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
supply Current 45mA or lower (at 24VDC and all points ON)
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity
noise frequency 25 to 60Hz (DC type noise simulator condition)
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
10MΩ or higher between all DC external terminals and ground (500VDC insulation
Insulation resistance
resistance tester)
Protection degree IP1XB
Weight 0.11kg
One-touch connector for communication [Transmission circuit]
Communication 5-pin IDC plug is sold separately: A6CON-L5P
part <Optional>
Online connector for communication: A6CON-LJ5P
External One-touch connector for power supply and FG
connection [Module power supply, I/O power supply, FG]
Power supply
system 5-pin IDC plug is sold separately: A6CON-PW5P, A6CON-PW5P-SOD
part
<Optional>
Online connector for power supply: A6CON-PWJ5P
Sensor connector (e-CON) [I/O signals]
I/O part
4-pin IDC plug is sold separately. 1
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Connector for Applicable cable:
communication FANC-110SBH, FA-CBL200PSBH, CS-110
0.66 to 0.98mm2 (AWG18)
Connector for
[φ2.2 to 3.0mm (A6CON-PW5P), φ2.0 to 2.3mm (A6CON-PW5P-SOD)]
Applicable power supply and
Wire diameter: 0.16mm or more
wire size FG
Insulating coating material: PVC (heat-resistant)
Sensor connector (e-CON).
Connector for
Applicable connector plugs are sold separately. 1
I/O 2
(applicable wire size: 0.08 to 0.5mm , depending on the connector plug)
Accessory User’s manual, Holding fixtures for screw installation

1: Refer to Section 1.6.2 for details.

5 - 53 5 - 53
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection

Pin number Signal name

1 DA
2 DB
CON A, B 3 DG
CON A
4 Empty
1
LINK CABLE 2
1 DA 5 SLD
2 DB
(IN) 3 1 (FG)
3 DG
4
4 Empty
5
5 SLD
2 +24V (UNIT)
CON B CON C, D 3 24G (UNIT)
1
1
LINK CABLE 2
DA
4 +24V (I/O)
2 DB
(OUT) 3
4
3 DG 5 24G (I/O)
4 Empty
5
5 SLD Pin number Signal name Pin number Signal name
One-touch connector for communication
1 +24V 1 +24V
CON C Insulation
UNIT POWER CABLE(IN)
1
1 FG
CON1 2 Empty 1 CON9 2 Empty 1
2
3
2 +24V(UNIT) (Y0) 3 24G (Y8) 3 24G
3 24G(UNIT)
4
4 +24V(I/O) 4 Y0 4 Y8
5
5 24G(I/O)
I/O POWER CABLE(IN)
1 +24V 1 +24V
CON D
UNIT POWER CABLE(OUT)
1
1 FG CON2 2 Empty 1 CON10 2 Empty 1
2
3
2 +24V(UNIT) (Y1) 3 24G (Y9) 3 24G
3 24G(UNIT)
4
5
4 +24V(I/O) 4 Y1 4 Y9
5 24G(I/O)
I/O POWER CABLE(OUT) 1 +24V 1 +24V
One-touch connector for power supply and FG
2
CON3 2 Empty 1 CON11 2 Empty 1
Constant-
voltage (Y2) 3 24G (YA) 3 24G
circuit
3 CON1 4 Y2 4 YA
1
1 +24V 1 +24V
2
3 CON4 2 Empty 1 CON12 2 Empty 1
Load 4
(Y3) 3 24G (YB) 3 24G
1 4 Y3 4 YB
1 +24V 1 +24V
CON16 CON5 2 Empty 1 CON13 2 Empty 1
1
2
(Y4) 3 24G (YC) 3 24G
Load
3 4 Y4 4 YC
4
1 +24V 1 +24V
CON6 2 Empty 1 CON14 2 Empty 1
(Y5) 3 24G (YD) 3 24G
4 Y5 4 YD
1 +24V 1 +24V
CON7 2 Empty 1 CON15 2 Empty 1
(Y6) 3 24G (YE) 3 24G
1: Since all No.2 pins of CON1 to CON16 are connected inside the module, they cannot be 4 Y6 4 YE
used. 1 +24V 1 +24V
2: Attach an unwired connector plug to an unused one-touch connector for power supply and CON8 2 Empty 1 CON16 2 Empty 1
FG. (Y7) 3 24G (YF) 3 24G
3: Wiring the sensor connector (e-CON) incorrectly may cause malfunction or failure due to 4 Y7 4 YF
short circuit of the power supply.

5 - 54 5 - 54
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection

<When using online connectors>

Online connector
for communication
CON A
1
1 DA
LINK CABLE 2
(IN) 2 DB
3
3 DG
4
4
5
5 SLD
CON B
1
1 DA
LINK CABLE 2
(OUT) 2 DB
3
3 DG
4
4
5
5 SLD
One-touch connector
for communication
CON C
1
UNIT POWER CABLE(IN) 1 FG
2
2 +24V(UNIT)
3
3 24G(UNIT)
4
4 +24V(I/O)
5
5 24G(I/O)
I/O POWER CABLE(IN) CON D
1
1 FG
2
UNIT POWER 2 +24V(UNIT)
CABLE(OUT) 3
3 24G(UNIT)
4
I/O POWER 4 +24V(I/O)
CABLE(OUT) 5
5 24G(I/O)

One-touch connector for power

supply and FG *1 Online connector
for power supply
and FG
1: Attach an unwired connector plug to an unused one-touch connector for power supply and FG.

Pin layout

Viewed from the front of the module

5 - 55 5 - 55
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

5.4 One-Touch Connector Type Output Module

5.4.1 AJ65VBTCU2-8T transistor output module (sink type)

Type Transistor output module

Item AJ65VBTCU2-8T Appearance
Number of output points 8 points
Isolation method Photocoupler
Rated load voltage 12/24VDC
Operating load voltage range 10.2 to 26.4VDC (ripple ratio: within 5%)
Max. load current 0.1A/point, 0.8A/common
Max. inrush current 0.7A, 10ms or less
Leakage current at OFF 0.1mA or lower
Max. voltage drop at ON 0.1VDC or lower (TYP.) 0.1A, 0.2VDC or lower (MAX.) 0.1A
Output type Sink type
Protection function Overload protection, overvoltage protection, overheat protection
OFF→ON 1ms or less
Response time
ON→OFF 1ms or less (rated load, resistive load)
External power supply for Voltage 10.2 to 26.4VDC (ripple ratio: within 5%) AJ65VBTCU2-8T
output part Current 5mA or lower (TYP., 24VDC/common) CON
A
Surge suppressor Zener diode
Wiring method for common 8 points/common (2-wire, one-touch connector type) CON
B
Number of occupied stations 32-point assignment/station (8 points used)
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%) Y0 PW
Module power supply
Current 35mA or lower (at 24VDC and all points ON) L RUN
Noise voltage 500Vp-p, noise width 1µs, Y1
L ERR
Noise immunity
noise frequency 25 to 60Hz (DC type noise simulator condition)
Y2
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground 0
1
10MΩ or higher between all DC external terminals and ground (500VDC insulation Y3 2
Insulation resistance 3
resistance tester) 4
Y4 5
Protection degree IP1XB 6
7
Weight 0.15kg
Y5
One-touch connector for communication
[Transmission circuit] Y6
Communication part 5-pin IDC plug is sold separately.
<Optional> Y7
Online connector for communication: A6CON-LJ5P
External
One-touch connector for power supply and FG
connection CON
[Module power supply, I/O power supply, FG]
system C
Power supply part 5-pin IDC plug is sold separately: A6CON-PW5P, A6CON-PW5P-SOD
<Optional> CON
Online connector for power supply: A6CON-PWJ5P D

One-touch connector for I/O

I/O part
4-pin IDC plug is sold separately.
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Connector for Applicable cable:
communication FANC-110SBH, FA-CBL200PSBH, CS-110
0.66 to 0.98mm2 (AWG18)
Connector for power supply [φ2.2 to 3.0mm (A6CON-PW5P), φ2.0 to 2.3mm (A6CON-PW5P-SOD)]
Applicable and FG Wire diameter: 0.16mm or more
wire size Insulating coating material: PVC (heat-resistant)
φ1.0 to 1.4 (A6CON-P214), φ1.4 to 2.0 (A6CON-P220)
[Applicable wire size: 0.14 to 0.2mm2]
Connector for I/O
φ1.0 to 1.4 (A6CON-P514), φ1.4 to 2.0 (A6CON-P520)
[Applicable wire size: 0.3 to 0.5mm2]
Accessory User’s manual

5 - 56 5 - 56
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection

Pin
Pin layout Signal name
number
1 DA
2 DB
CON
3 DG
A, B
4 Empty

CONA
5 SLD
1
1 DA 1 Y0
LINK CABLE 2
2 DB
(IN) 3 2 Empty
4
3 DG CON1
4 Empty 3 +24V
5
5 SLD
4 Empty
CONB 5 4 3 2 1
1
1 DA 1 Y1
LINK CABLE 2
(OUT)
2 DB CONA 2 Empty
3
3 DG CON2
4
4 Empty CONB 3 +24V
5
5 SLD 4 Empty
One-touch connector for communication 43 2 1 1 Y2
CONC
1 Insulation
UNIT POWER CABLE(IN) 1 FG CON1 2 Empty
2
2 +24V(UNIT)
CON3
3 3 +24V
3 24G(UNIT)
4 CON2
4 +24V(I/O) 4 Empty
5
5 24G(I/O)
CON3 1 Y3
I/O POWER CABLE(IN) COND
UNIT POWER CABLE(OUT)
1
1 FG
2 Empty
2 CON4 CON4
3
2 +24V(UNIT) 3 +24V
3 24G(UNIT)
4
4 +24V(I/O) CON5 4 Empty
5
5 24G(I/O) 1 Y4
I/O POWER CABLE(OUT) Constant-voltage circuit
1 CON6 2 Empty
One-touch connector for power supply and FG CON5
CON1
Load 3 +24V
1 CON7
2 4 Empty
3
CON8 1 Y5
4
2 Empty
5 4 3 2 1 CON6
3 +24V
CONC 4 Empty
1 Y6
CON8 COND
2 Empty
Load 1 CON7
2 3 +24V
3
Viewed from the
front of the module 4 Empty
4
1 Y7
2 Empty
CON8
3 +24V
4 Empty
1 (FG)
2 +24V (UNIT)
CON
3 24G (UNIT)
C, D
4 +24V (I/O)
1: Attach an unwired connector plug to an unused one-touch connector for power supply and FG. 5 24G (I/O)

5 - 57 5 - 57
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection

<When using online connectors>

Online connector
for communication
CONA
1
1 DA
LINK CABLE 2
(IN) 2 DB
3
3 DG
4
4
5
5 SLD
CONB
1
1 DA
LINK CABLE 2
(OUT) 2 DB
3
3 DG
4
4
5
5 SLD
One-touch connector
for communication
CONC
1
UNIT POWER CABLE(IN) 1 FG
2
2 +24V(UNIT)
3
3 24G(UNIT)
4
4 +24V(I/O)
5
5 24G(I/O)
I/O POWER CABLE(IN) COND
1
1 FG
2
UNIT POWER 2 +24V(UNIT)
CABLE(OUT) 3
3 24G(UNIT)
4
I/O POWER 4 +24V(I/O)
CABLE(OUT) 5
5 24G(I/O)

One-touch connector for power

supply and FG *1 Online connector
for power supply
and FG

1: Attach an unwired connector plug to an unused one-touch connector for power supply and FG.

5 - 58 5 - 58
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

5.4.2 AJ65VBTCU2-16T transistor output module (sink type)

Type Transistor output module

Item AJ65VBTCU2-16T Appearance
Number of output points 16 points
Isolation method Photocoupler
Rated load voltage 12/24VDC
Operating load voltage range 10.2 to 26.4VDC (ripple ratio: within 5%)
Max. load current 0.1A/point, 1.6A/common
Max. inrush current 0.7A, 10ms or less
Leakage current at OFF 0.1mA or lower
Max. voltage drop at ON 0.1VDC or lower (TYP.) 0.1A, 0.2VDC or lower (MAX.) 0.1A
Output type Sink type
Protection function Overload protection, overvoltage protection, overheat protection
OFF→ON 1ms or less
Response time
ON→OFF 1ms or less (resistive load)
External power Voltage 10.2 to 26.4VDC (ripple ratio: within 5%)
supply for output
part Current 10mA or lower (TYP. 24VDC/common), excluding external load current
A J65VBTCU2-16T
Surge suppressor Zener diode CON
A
Wiring method for common 16 points/common (2-wire, one-touch connector type)
Number of occupied stations 32-point assignment/station (16 points used) CON
B
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
supply Current 40mA or lower (at 24VDC and all points ON) PW

L RUN
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity L ERR
noise frequency 25 to 60Hz (DC type noise simulator condition)
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground 0
1
10MΩ or higher between all DC external terminals and ground (500VDC insulation 2
Insulation resistance 3
4
resistance tester) 5
6
Protection degree IP1XB 7
Weight 0.19kg
8
One-touch connector for communication 9
A
[Transmission circuit] B
C
Communication D
5-pin IDC plug is sold separately. E
part Y0 Y7 Y8 YF F
<Optional>
Online connector for communication: A6CON-LJ5P CON
External C
One-touch connector for power supply and FG
connection
[Module power supply, I/O power supply, FG] CON
system D
Power supply part 5-pin IDC plug is sold separately: A6CON-PW5P, A6CON-PW5P-SOD
<Optional>
Online connector for power supply: A6CON-PWJ5P
One-touch connector for I/O
I/O part
4-pin IDC plug is sold separately.
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Connector for Applicable cable:
communication FANC-110SBH, FA-CBL200PSBH, CS-110
0.66 to 0.98mm2 (AWG18)
Connector for
[φ2.2 to 3.0mm (A6CON-PW5P), φ2.0 to 2.3mm (A6CON-PW5P-SOD)]
power supply and
Applicable Wire diameter: 0.16mm or more
FG
wire size Insulating coating material: PVC (heat-resistant)
φ1.0 to 1.4 (A6CON-P214), φ1.4 to 2.0 (A6CON-P220)
[Applicable wire size: 0.14 to 0.2mm2]
Connector for I/O
φ1.0 to 1.4 (A6CON-P514), φ1.4 to 2.0 (A6CON-P520)
[Applicable wire size: 0.3 to 0.5mm2]
Accessory User’s manual

5 - 59 5 - 59
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection
Pin
Pin layout Signal name
number
1 DA
2 DB
CON
3 DG
A, B
4 Empty
5 SLD
1 Y0
CON 2 Empty
1 3 +24V
4 Empty
1 Y1
CON 2 Empty
2 3 +24V
4 Empty
1 Y2
CON 2 Empty
3 3 +24V
1
CONA 4 Empty
1 DA 1 Y3
LINK CABLE 2
2 DB
(IN) 3
3 DG
CON 2 Empty
4
4 Empty 4 3 +24V
5
5 SLD 4 Empty
CONB 1 Y4
1
1 DA CON 2 Empty
LINK CABLE 2
(OUT) 3
2 DB 5 3 +24V
3 DG
4 4 Empty
4 Empty
5
5 SLD 1 Y5
5 4 3 2 1
One-touch connector for communication
CON 2 Empty
CONC
CONA 6 3 +24V
1 Insulation
UNIT POWER CABLE(IN) 1 FG CONB 4 Empty
2
3
2 +24V(UNIT)
4321 4321
1 Y6
3 24G(UNIT)
4 CON 2 Empty
4 +24V(I/O) CON1 CON9
5 7 3 +24V
5 24G(I/O)
I/O POWER CABLE(IN) CON2 CON10 4 Empty
COND
UNIT POWER CABLE(OUT)
1
1 FG CON3 CON11 1 Y7
2 CON 2 Empty
2 +24V(UNIT)
3 CON4 CON12
3 24G(UNIT) 8 3 +24V
4
4 +24V(I/O) CON5 CON13 4 Empty
5
5 24G(I/O)
I/O POWER CABLE(OUT) Constant-voltage circuit CON6 CON14
1 Y8
One-touch connector for power supply and FG
1 CON 2 Empty
CON7 CON15 9
CON1 3 +24V
Load 1
CON8 CON16 4 Empty
2
3
1 Y9
5 4 3 2 1
4 CON 2 Empty
CONC 10 3 +24V
COND 4 Empty
1 YA
Viewed from the CON 2 Empty
front of the module 11 3 +24V
CON16
Load 4 Empty
1
2
1 YB
3 CON 2 Empty
4 12 3 +24V
4 Empty
1 YC
CON 2 Empty
13 3 +24V
4 Empty
1 YD
CON 2 Empty
14 3 +24V
4 Empty
1 YE
CON 2 Empty
15 3 +24V
4 Empty
1 YF
CON 2 Empty
16 3 +24V
4 Empty
1 (FG)
1: Attach an unwired connector plug to an unused one-touch connector for power supply and 2 +24V (UNIT)
CON
3 24G (UNIT)
FG. C, D
4 +24V (I/O)
5 24G (I/O)

5 - 60 5 - 60
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection

<When using online connectors>

Online connector
for communication
CONA
1
1 DA
LINK CABLE 2
(IN) 2 DB
3
3 DG
4
4
5
5 SLD
CONB
1
1 DA
LINK CABLE 2
(OUT) 2 DB
3
3 DG
4
4
5
5 SLD
One-touch connector
for communication
CONC
1
UNIT POWER CABLE(IN) 1 FG
2
2 +24V(UNIT)
3
3 24G(UNIT)
4
4 +24V(I/O)
5
5 24G(I/O)
I/O POWER CABLE(IN) COND
1
1 FG
2
UNIT POWER 2 +24V(UNIT)
CABLE(OUT) 3
3 24G(UNIT)
4
I/O POWER 4 +24V(I/O)
CABLE(OUT) 5
5 24G(I/O)

One-touch connector for power

supply and FG *1 Online connector
for power supply
and FG

1: Attach an unwired connector plug to an unused one-touch connector for power supply and FG.

5 - 61 5 - 61
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

5.4.3 AJ65SBTC1-32T transistor output module (sink type)

Type Transistor output module

Item AJ65SBTC1-32T Appearance
Number of output points 32 points
Isolation method Photocoupler
Rated load voltage 12/24VDC
Operating load voltage range 10.2 to 26.4VDC (ripple ratio: within 5%)
Max. load current 0.1A/point, 3.2A/common
Max. inrush current 1.0A, 10ms or less
Leakage current at OFF 0.25mA or lower
Max. voltage drop at ON 0.3VDC or lower (TYP.) 0.1A, 0.6VDC or lower (MAX.) 0.1A
Output type Sink type
Protection function Overload protection, overvoltage protection, overheat protection
OFF→ON 0.5ms or less
Response time
ON→OFF 1.5ms or less (resistive load)
External power supply for output Voltage 10.2 to 26.4VDC (ripple ratio: within 5%)
part Current 50mA or lower (TYP. 24VDC/common), excluding external load current

ON
Surge suppressor Zener diode

COM-
CTL+
Wiring method for common 32 points/common (1-wire, one-touch connector type)

B RATE
40 20 10 8 4 2 1 4 2 1
Number of occupied stations 32-point assignment/station (32 points used)

Y1C
Y1D
Y1E
Y1F
STATION NO.
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
Module power supply

Y1A
Y1B
Y18
Y19
Current 60mA or lower (at 24VDC and all points ON)
Noise voltage 500Vp-p, noise width 1µs,

Y14
Y15
Y16
Y17
Noise immunity
noise frequency 25 to 60Hz (DC type noise simulator condition)

Y10-Y1F
Y0-YF

Y10
Y11
Y12
Y13
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
10MΩ or higher between all DC external terminals and ground (500VDC

YC
YD
YE
YF
Y1011121314 1516 17 Y18 19 1A1B1C1D1E1F
Y8 9 A B C D E F
Insulation resistance
insulation resistance tester)

YA
YB
Y8
Y9
A J65SBTC1-32T
Protection degree IP2X

Y4
Y5
Y6
Y7
Weight 0.16kg
7-point two-piece terminal block

Y0
Y1
Y2
Y3
Y0 1 2 3 4 5 6 7

Communication part, [Transmission circuit, module power supply, FG]

module power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)

(FG)
Applicable solderless terminal: 2 or less 24G
External
DA DG +24V

2-point direct-mount terminal block

SLD

connection
[I/O power supply]
system I/O power supply part
DB

M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)

Applicable solderless terminal: 2 or less
Dedicated one-touch connector [I/O signals]
I/O part
4-pin IDC plug is sold separately.
M4 screw with plain washer finished round
Module mounting screw (tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Communication part, y RAV1.25-3 (compliant with JIS C 2805)
Applicable
module power supply [Applicable wire size: 0.3 to 1.25mm2]
solderless
part y V2-MS3, RAP2-3SL, TGV2-3N
terminal
Applicable I/O power supply part [Applicable wire size: 1.25 to 2.0mm2]
wire size φ1.0 to 1.4 (A6CON-P214), φ1.4 to 2.0 (A6CON-P220)
[Applicable wire size: 0.14 to 0.2 mm2]
I/O part
φ1.0 to 1.4 (A6CON-P514), φ1.4 to 2.0 (A6CON-P520)
[Applicable wire size: 0.3 to 0.5 mm2]
Accessory User’s manual

5 - 62 5 - 62
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection
Terminal
Signal name
number
TB1 DA
TB2 DB
TB3 DG
1 DA TB4 SLD
2 DB TB5 +24V
3 DG Insulation TB6 (FG)
4 SLD
5 +24V
TB7 24G
6 FG Pin number Signal name
7 24G 1 Y0
Module power supply
CON1 2 Y1
Load
1 CON1
3 Y2
2
3 4 Y3
Load
4 1 Y4
2 Y5
CON2
3 Y6
4 Y7
1 Y8
2 Y9
CON3
3 YA
4 YB
1 YC
CON8
Load 2 YD
1 CON4
2 3 YE
3 4 YF
Load 4
1 Y10
2 Y11
CON5
3 Y12
4 Y13
1 Y14
2 Y15
CON6
External power supply 3 Y16
for output part 4 Y17
8 CTL+ 1 Y18
9 COM-
2 Y19
CON7
Constant-voltage circuit 3 Y1A
Load
Load power supply External power supply for output
4 Y1B
part and load power supply 1 Y1C
8 CTL+
(common) 2 Y1D
9 COM- CON8
3 Y1E
4 Y1F
Terminal
Signal name
number
TB8 CLT+
TB9 COM-
Pin layout

Viewed from the front of the module

5 - 63 5 - 63
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

5.4.4 AJ65SBTC1-32T1 transistor output module (sink type)

Type Transistor output module

Item AJ65SBTC1-32T1 Appearance
Number of output points 32 points
Isolation method Photocoupler
Rated load voltage 12/24VDC
Operating load voltage range 10.2 to 26.4VDC (ripple ratio: within 5%)
Max. load current 0.1A/point, 3.2A/common
Max. inrush current 1.0A, 10ms or less
Leakage current at OFF 0.1mA or lower
Max. voltage drop at ON 0.3VDC or lower (TYP.) 0.1A, 0.6VDC or lower (MAX.) 0.1A
Output type Sink type
Protection function None
OFF→ON 0.5ms or less
Response time
ON→OFF 1.5ms or less (resistive load)
External power supply Voltage 10.2 to 26.4VDC (ripple ratio: within 5%)
for output part Current 50mA or lower (TYP. 24VDC/common), excluding external load current
Surge suppressor Zener diode

ON
Wiring method for common 32 points/common (1-wire, one-touch connector type)

COM-
CTL+
B RATE
Number of occupied stations 32-point assignment/station (32 points used)

40 20 10 8 4 2 1 4 2 1
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

Y1C
Y1D
Y1E
Y1F
Module power supply

STATION NO.
Current 60mA or lower (at 24VDC and all points ON)

Y1A
Y1B
Y18
Y19
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity
noise frequency 25 to 60Hz (DC type noise simulator condition)

Y14
Y15
Y16
Y17
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

Y10-Y1F
Y0-YF

Y10
Y11
Y12
Y13
10MΩ or higher between all DC external terminals and ground (500VDC
Insulation resistance
insulation resistance tester)

YC
YD
YE
YF
Y1011121314 1516 17 Y18 19 1A1B1C1D1E1F
Y8 9 A B C D E F
Protection degree IP2X

YA
YB
Y8
Y9
A J65SBTC1-32T1
Weight 0.16kg

Y4
Y5
Y6
Y7
7-point two-piece terminal block
Communication part, [Transmission circuit, module power supply, FG]

Y0
Y1
Y2
Y3
Y0 1 2 3 4 5 6 7

module power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
(FG)
24G
External
2-point direct-mount terminal block
connection
DA DG +24V

[I/O power supply]

SLD

system I/O power supply part

M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
DB

Applicable solderless terminal: 2 or less

Dedicated one-touch connector [I/O signals]
I/O part
4-pin IDC plug is sold separately.
M4 screw with plain washer finished round
Module mounting screw (tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Communication
part, y RAV1.25-3 (compliant with JIS C 2805)
Applicable
module power [Applicable wire size: 0.3 to 1.25mm2]
solderless
supply part y V2-MS3, RAP2-3SL, TGV2-3N
terminal
Applicable I/O power supply [Applicable wire size: 1.25 to 2.0mm2]
wire size part
φ1.0 to 1.4 (A6CON-P214), φ1.4 to 2.0 (A6CON-P220)
[Applicable wire size: 0.14 to 0.2mm2]
I/O part
φ1.0 to 1.4 (A6CON-P514), φ1.4 to 2.0 (A6CON-P520)
[Applicable wire size: 0.3 to 0.5mm2]
Accessory User’s manual

5 - 64 5 - 64
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection
Terminal
Signal name
number
TB1 DA
TB2 DB
TB3 DG
1 DA TB4 SLD
2 DB
TB5 +24V
3 DG Insulation
4 SLD TB6 (FG)
5 +24V TB7 24G
6 FG Pin number Signal name
7 24G
Module power supply 1 Y0
CON1
Load 2 Y1
1 CON1
2 3 Y2
3 4 Y3
Load 4
1 Y4
2 Y5
CON2
3 Y6
4 Y7
1 Y8
2 Y9
CON3
3 YA
4 YB

CON8
1 YC
Load 1 2 YD
CON4
2 3 YE
3 4 YF
Load 4
1 Y10
2 Y11
CON5
3 Y12
4 Y13
1 Y14
2 Y15
External power CON6
3 Y16
supply for output part
4 Y17
8 CTL+ 1 Y18
9 COM-
2 Y19
CON7
Load power supply 3 Y1A
Constant-voltage circuit
Load 4 Y1B
External power supply for output part 1 Y1C
and load power supply (common) 2 Y1D
8 CTL+
CON8
9 COM- 3 Y1E
4 Y1F
Terminal
Signal name
number
TB8 CLT+
TB9 COM-
Pin layout

Viewed from the front of the module

5 - 65 5 - 65
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

5.5 FCN Connector Type Output Module

5.5.1 AJ65SBTCF1-32T type transistor output module (sink type)
Type Triac output module
Item AJ65SBTCF1-32T Appearance
Number of output points 32 points
Isolation method Photocoupler
Rated load voltage 12/24VDC
Operating load voltage range 10.2 to 26.4VDC (ripple ratio: within 5%)
Max. load current 0.1A/point, 3.2A/common
Max. inrush current 1.0A, 10ms or less
Leakage current at OFF 0.1mA or lower
Max. voltage drop at ON 0.1VDC or lower (TYP.) 0.1A, 0.2VDC or lower (MAX.) 0.1A
Output type Sink type
Protection function Overload protection, overvoltage protection, overheat protection
OFF→ON 0.5ms or less
Response time
ON→OFF 1.5ms or less (resistive load)
External power supply for Voltage 10.2 to 26.4VDC (ripple ratio: within 5%)

ON
output part Current 50mA or lower (TYP. 24VDC/common), excluding external load current

Y0 Y1 Y2 Y3 Y4 Y5 Y6 Y7 Y8 Y9 YA YB YC YD YE YF NC NC CTL+ CTL+
B RATE

Y10 Y11 Y12 Y13 Y14 Y15 Y16 Y17 Y18 Y19 Y1A Y1B Y1C Y1D Y1E Y1F NC NC COM- COM-
40 20 10 8 4 2 1 4 2 1
Surge suppressor Zener diode
Wiring method for common 32 points/common (1-wire, FCN connector type)

STATION NO.
Number of occupied stations 32-point assignment/station (32 points used)
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
Module power supply
Current 60mA or lower (at 24VDC and all points ON)

Y10-Y1F
Noise voltage 500Vp-p, noise width 1µs,

Y0-YF
Noise immunity
noise frequency 25 to 60Hz (DC type noise simulator condition)

Y10 11 1213 1415 1617 Y18191A1B1C1D1E1F

Y8 9 A B C D E F
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
10MΩ or higher between all DC external terminals and ground (500VDC

A J65SBTCF1-32T
Insulation resistance
insulation resistance tester)
Weight 0.15kg
7-point two-piece terminal block
Y0 1 2 3 4 5 6 7

Communication part, [Transmission circuit, module power supply, FG]

External

(FG)
24G
module power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
connection
Applicable solderless terminal: 2 or less +24V
system
I/O power supply part, 40-pin connector [I/O power supply, I/O signal]
SLD
DG

I/O part (A6CON1, A6CON2, A6CON3, A6CON4)

DB
DA

M4 screw with plain washer finished round

Module mounting screw (tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Communication y RAV1.25-3 (compliant with JIS C 2805)
Applicable
part, [Applicable wire size: 0.3 to 1.25mm2]
solderless
module power y V2-MS3, RAP2-3SL, TGV2-3N
terminal
Applicable supply part [Applicable wire size: 1.25 to 2.0mm2]
2
wire size 0.3mm (AWG22) or less (A6CON1 and A6CON4)
2
I/O power supply part, 0.2 to 0.08mm (AWG28 to 24) (A6CON2)
2
I/O part 0.08mm (AWG28) stranded wire, φ0.25mm (AWG30) single wire
(A6CON3)
Applicable connector/
A6TBXY36, A6TBXY54
terminal block conversion module
Accessory User’s manual

5 - 66 5 - 66
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection
Pin layout Terminal number Signal name
TB1 DA
TB2 DB
1 DA
2 DB TB3 DG
3 DG Insulation TB4 SLD
4 SLD TB5 +24V
5 +24V
TB6 (FG)
6 FG
7 24G TB7 24G
Module power supply Pin Signal Pin Signal
Load number name number name
B20 Y0
B19 Y1 B20 Y0 A20 Y10
B18 Y2 B19 Y1 A19 Y11
B17 Y3 B18 Y2 A18 Y12
B16 Y4
B17 Y3 A17 Y13
B15 Y5
B14 Y6 B16 Y4 A16 Y14
B13 Y7 B15 Y5 A15 Y15
B12 Y8 B14 Y6 A14 Y16
B11 Y9
B13 Y7 A13 Y17
B10 YA
B9 YB B12 Y8 A12 Y18
B8 YC B11 Y9 A11 Y19
B7 YD B10 YA A10 Y1A
B6 YE
B9 YB A9 Y1B
B5 YF
A20 Y10 B8 Y0 A8 Y1C
Viewed from the
A19 Y11 B7 YD A7 Y1D
front of the module
A18 Y12 B6 YE A6 Y1E
A17 Y13
B5 YF A5 Y1F
A16 Y14
A15 Y15
B4 Empty A4 Empty
A14 Y16 B3 Empty A3 Empty
A13 Y17 B2 CTL+ A2 COM-
A12 Y18
B1 CTL+ A1 COM-
A11 Y19
A10 Y1A
A9 Y1B
A8 Y1C
A7 Y1D
Load A6 Y1E
A5 Y1F
B1,2 CTL+
External power supply
A1,2 COM
for output part

Load power supply

Constant-voltage circuit

Load
External power supply for output part
and load power supply (common)
B1,2 CTL+
A1,2 COM

5 - 67 5 - 67
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

5.6 Waterproof Type Output Module

5.6.1 AJ65FBTA2-16T transistor output module (sink type)

Type Transistor output module

Item AJ65FBTA2-16T Appearance
Number of output points 16 points
Isolation method Photocoupler
Rated load voltage 12/24VDC
Operating load voltage range 10.2 to 28.8VDC (ripple ratio: within 5%)
Max. load current 0.5A/point, 4A/common
Max. inrush current 1.0A, 10ms or less
Leakage current at OFF 0.25mA or lower
Max. voltage drop at ON 0.15VDC or lower (TYP.) 0.5A, 0.25VDC or lower (MAX.) 0.5A AJ65FBTA2-16T

Output type Sink type

Protection function Overload protection, overheat protection Y8
Y9
YA
YB

OFF→ON 0.5ms or less YC

YD

Response time YE
YF

ON→OFF 1.5ms or less (resistive load)

External power supply Voltage 10.2 to 28.8VDC (ripple ratio: within 5%)
for output part Current 20mA or lower (at 24VDC and all points ON), excluding external load current
Surge suppressor Zener diode
Wiring method for common 16 points/common (2-wire, waterproof connector type) Y
Y
Y
Y
Number of occupied stations 32-point assignment/station (16 points used)
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
Module power supply Y Y
Current 50mA or lower (at 24VDC and all points ON) Y Y

Noise voltage 500Vp-p, noise width 1µs,

Noise immunity
noise frequency 25 to 60Hz (DC type noise simulator condition)
Y Y
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground Y Y

10MΩ or higher between all DC external terminals and ground (500VDC insulation
Insulation resistance
resistance tester)
Y Y
Protection degree IP67 Y Y

Weight 0.40kg
Accessory User’s manual
Optional item Waterproof cap: A6CAP-WP2 (20 pieces)
Other connecting devices Refer to Section 1.6.1.

5 - 68 5 - 68
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection
Pin layout Connector for communication
Pin
LINK IN LINK OUT
number
1 SLD SLD
LINK IN 2 DB DB
4
2 3 DG DG
3
4 DA DA
1 Communication
circuit 5 No pins Empty
110
Connector for power supply
LINK OUT 130 Pin
4 UNIT POWER AUX.
2 LINK IN number
3 Terminating resistor Male 1 +24V(UNIT) +24V(I/O)
1 setting switch 2 1
5 3 4
2 Empty Empty
3 24G(UNIT) 24G(I/O)
4 Empty Empty
LINK OUT
Insulation 5 FG FG
UNIT POWER Female
1 Connector for I/O
1 2
3 5
4 3 Pin Signal Pin Signal
5
number name number name
2
4 UNIT POWER/AUX. 1 +24V 1 +24V
Module mounting screw (FG)
2 Y1 2 Y9
Male Y0 Y8
2 1 Y1 3 Empty Y9 3 Empty
5
3 4
AUX. 4 Y0 4 Y8
1
3 5 Empty 5 Empty
5 I/O connector
Constant-voltage 1 +24V 1 +24V
2
4 circuit Female 2 Y3 2 YB
1 2 Y2 YA
4 5
3 Y3 3 Empty YB 3 Empty
Connector for I/O 4 Y2 4 YA

Load
5 Empty 5 Empty
4
Load 2 Front view 1 +24V 1 +24V
1 2 Y5 2 YD
3 Y4 YC
Y5 3 Empty YD 3 Empty
5
4 Y4 4 YC
5 Empty 5 Empty
1 +24V 1 +24V
2 Y7 2 YF
Y6 YE
Y7 3 Empty YF 3 Empty
4 Y6 4 YE
5 Empty 5 Empty

Load 4
Load 2
1
3
5

5 - 69 5 - 69
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

5.6.2 AJ65FBTA2-16TE transistor output module (source type)

Type Transistor output module

Item AJ65FBTA2-16TE Appearance
Number of output points 16 points
Isolation method Photocoupler
Rated load voltage 12/24VDC
Operating load voltage range 10.2 to 28.8VDC (ripple ratio: within 5%)
Max. load current 1.0A/point, 4A/common
Max. inrush current 2.0A, 10ms or less
Leakage current at OFF 0.3mA or lower
Max. voltage drop at ON 0.15VDC or lower (TYP.) 1.0A, 0.2VDC or lower (MAX.) 1.0A
AJ65FBTA2-16TE
Output type Source type
Overload protection, overheat protection PROTECT

Protection function Y8
Y9

(The LED turns on when any protection is activated.) YA

YB
YC
YD

OFF→ON 0.5ms or less YE

YF

Response time
ON→OFF 1.5ms or less (resistive load)
External power supply for Voltage 10.2 to 28.8VDC (ripple ratio: within 5%)
output part Current 30mA or lower (at 24VDC and all points ON), excluding external load current
Surge suppressor Zener diode
Y Y

Wiring method for common 16 points/common (2-wire, waterproof connector type) Y Y

Number of occupied stations 32-point assignment/station (16 points used)

Voltage 20.4 to 26.4VDC (ripple ratio: within 5%) Y Y
Module power supply Y Y
Current 50mA or lower (at 24VDC and all points ON)
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity
noise frequency 25 to 60Hz (DC type noise simulator condition) Y Y
Y Y
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
10MΩ or higher between all DC external terminals and ground (500VDC
Insulation resistance
insulation resistance tester) Y
Y
Y
Y

Protection degree IP67

Weight 0.40kg
Accessory User’s manual
Optional item Waterproof cap: A6CAP-WP2 (20 pieces)
Other connecting devices Refer to Section 1.6.1.

5 - 70 5 - 70
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

External connection
Pin layout Connector for communication
Pin
LINK IN LINK OUT
number
LINK IN 1 SLD SLD
4
2 2 DB DB
3 3 DG DG
1 Communication
circuit 4 DA DA
110 5 No pins Empty
LINK OUT 130 Connector for power supply
4
2
Pin
UNIT POWER AUX.
3 Terminating resistor
number
LINK IN
1 setting switch 1 +24V(UNIT) +24V(I/O)
5 Male
2 1 2 Empty Empty
3 4
3 24G(UNIT) 24G(I/O)
4 Empty Empty
Insulation LINK OUT
UNIT POWER 5 FG FG
1
Female Connector for I/O
3
1 2
5 4 5
3 Pin Signal Pin Signal
2
number name number name
4
Module mounting screw (FG) UNIT POWER/AUX. 1 Empty 1 Empty
Male 2 Y1 2 Y9
Y0 Y8
AUX. 2 5
1
Y1 3 24G Y9 3 24G
1 3 4

3 4 Y0 4 Y8
5 Constant-voltage 5 Empty 5 Empty
2 circuit I/O connector
1 Empty 1 Empty
4 Female
1 2 2 Y3 2 YB
4 5
3 Y2 YA
Y3 3 24G YB 3 24G
4 Y2 4 YA
Connector for I/O 5 Empty 5 Empty
Front view
Load 4 1 Empty 1 Empty
Load 2 2 Y5 2 YD
1 Y4 YC
3 Y5 3 24G YD 3 24G
5 4 Y4 4 YC
5 Empty 5 Empty
1 Empty 1 Empty
2 Y7 2 YF
Y6 YE
Y7 3 24G YF 3 24G
4 Y6 4 YE
5 Empty 5 Empty

Load 4
Load 2
1
3
5

5 - 71 5 - 71
5 SPECIFICATIONS FOR OUTPUT MODULES
MELSEC-A

MEMO

5 - 72 5 - 72
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6 SPECIFICATIONS FOR COMBINED MODULES

This chapter describes the specifications for a combined module that can be
connected to the CC-Link system.

6.1 Terminal Block Type Combined Module

6.1.1 AJ65SBTB32-8DT combined module

Type DC input transistor output combined module

Item AJ65SBTB32-8DT Appearance
Input Output
Number of input points 4 points Number of output points 4 points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 24VDC
19.2 to 26.4VDC
Rated input current Approx. 7mA Operating load voltage range
(ripple ratio: within 5%)
19.2 to 26.4VDC
Operating voltage range Max. load current 0.5A/point, 1.2A/common
(ripple ratio: within 5%)
Max. number of simultaneous
100% Max. inrush current 1.0A, 10ms or less
input points
14VDC or higher/
ON voltage/ON current Leakage current at OFF 0.25mA or lower
3.5mA or higher
6VDC or lower/ 0.3VDC or lower (TYP.) 0.5A,
OFF voltage/OFF current Max. voltage drop at ON
1.7mA or lower 0.6VDC or lower (MAX.) 0.5A
Output type Sink type
Input resistance Approx. 3.3kΩ Overload protection, overvoltage
Protection function
protection, overheat protection
OFF→ON 1.5ms or less (at 24VDC) OFF→ON 0.5ms or less
Response time
ON→OFF 1.5ms or less (at 24VDC)
Response time
ON→OFF 1.5ms or less (resistive load) 6

COM+ COM- COM+ COM- COM+ COM+ COM+ COM+ DC24G

19.2 to 26.4VDC

DC24V
B RATE
40 20 10 8 4 2 1 4 2 1
Voltage
External power (ripple ratio: within 5%)

YB
supply for 14.6mA or lower STATION NO.

YA
output part Current (at 24VDC and all points ON),
Y9
excluding external load current
ON

Y8

Input type Positive common (sink type) Surge suppressor Zener diode
X3

Supply current for connected

1.0A or lower/common
X2

device
AJ65SBTB32-8DT
X1

Wiring method for common 8 points/common (input: 3-wire terminal block type, output: 2-wire terminal block type)
X0

Number of occupied stations 32-point assignment/station (8 points used)

X0 1 2 3 Y8 9 A B

Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

(FG)
24G

supply Current 45mA or lower (at 24VDC and all points ON)
+24V

Noise voltage 500Vp-p, noise width 1µs,

SLD

Noise immunity
DG

noise frequency 25 to 60Hz (DC type noise simulator condition)

DB
DA

Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
10MΩ or higher between all DC external terminals and ground (500VDC insulation resistance
Insulation resistance
tester)
Protection degree IP2X
Weight 0.18kg
Communication
7-point two-piece terminal block [Transmission circuit, module power supply, FG]
part,
M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
External module power
Applicable solderless terminal: 2 or less
connection supply part
system I/O power supply 18-point direct-mount terminal block [I/O power supply, I/O signal]
part, M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
I/O part Applicable solderless terminal: 2 or less
M4 screw with plain washer finished round (tightening torque range: 0.78 to 1.08N•m)
Module mounting screw
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
2
[Applicable wire size: 0.3 to 1.25mm ]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
2
[Applicable wire size: 1.25 to 2.0mm ]
Accessory User’s manual

6-1 6-1
 6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection
Terminal
Signal name
number
1 DA TB1 DA
2 DB TB2 DB
3 DG Insulation TB3 DG
4 SLD TB4 SLD
5 +24V TB5 +24V
6 FG
TB6 (FG)
7 24G
Module power supply TB7 24G
Black TB8 X0
3-wire sensor 8 X0
Brown TB9 COM+
9 COM+
Blue TB10 X1
10 X1
11 COM- TB11 COM-
12 X2 TB12 X2
13 COM+ TB13 COM+
14 X3 TB14 X3
Load 15 COM-
TB15 COM-
16 Y8
17 COM+ TB16 Y8
18 Y9 TB17 COM+
19 COM+ TB18 Y9
20 YA TB19 COM+
Load 21 COM+
TB20 YA
22 YB
23 COM+
TB21 COM+
24 DC24V TB22 YB
25 DC24G TB23 COM+
External power supply
TB24 DC24V
for output part
TB25 DC24G
Constant-voltage circuit

6-2 6-2
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.1.2 AJ65SBTB32-8DT2 combined module

Type DC input transistor output combined module

Item AJ65SBTB32-8DT2 Appearance
Input Output
Number of input points 4 points Number of output points 4 points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 24VDC
Operating load voltage 19.2 to 26.4VDC
Rated input current Approx. 7mA
range (ripple ratio: within 5%)
19.2 to 26.4VDC
Operating voltage range Max. load current 0.5A/point, 1.2A/common
(ripple ratio: within 5%)
Max. number of simultaneous
100% Max. inrush current 1.0A, 10ms or less
input points
14VDC or higher/3.5mA or
ON voltage/ON current Leakage current at OFF 0.1mA or lower
higher
0.3VDC or lower (TYP.) 0.5A,
OFF voltage/OFF current 6VDC or lower/1.7mA or lower Max. voltage drop at ON
0.6VDC or lower (MAX.) 0.5A
Output type Sink type
Input resistance Approx. 3.3kΩ
Protection function None
OFF→ON 1.5ms or less (at 24VDC) Response OFF→ON 0.5ms or less
Response time
ON→OFF 1.5ms or less (at 24VDC) time ON→OFF 1.5ms or less (resistive load)
19.2 to 26.4VDC

COM+ COM- COM+ COM- COM+ COM+ COM+ COM+ DC24G

External Voltage
(ripple ratio: within 5%)

DC24V
B RATE
40 20 10 8 4 2 1 4 2 1
power
14.6mA or lower

YB
supply for

STATION NO.
Current (at 24VDC and all points ON),

YA
output part
excluding external load current

Y9
Input type Positive common (sink type) Surge suppressor Zener diode

ON

Y8
Supply current for connected
1.0A or lower/common

X3
device

X2
AJ65SBTB32-8DT2
Wiring method for common 8 points/common (input: 3-wire terminal block type, output: 2-wire terminal block type)

X1
Number of occupied stations 32-point assignment/station (8 points used)

X0
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
X0 1 2 3 Y8 9 A B
supply Current 45mA or lower (at 24VDC and all points ON)

(FG)
24G
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity
noise frequency 25 to 60Hz (DC type noise simulator condition) DA DG +24V
DB SLD
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
10MΩ or higher between all DC external terminals and ground (500VDC insulation resistance
Insulation resistance
tester)
Protection degree IP2X
Weight 0.18kg
Communication 7-point two-piece terminal block
part, [Transmission circuit, module power supply, FG]
module power M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
External
supply part Applicable solderless terminal: 2 or less
connection
18-point direct-mount terminal block
system I/O power supply
[I/O power supply, I/O signal]
part,
M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
I/O part
Applicable solderless terminal: 2 or less
M4 screw with plain washer finished round (tightening torque range: 0.78 to 1.08N•m)
Module mounting screw
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

6-3 6-3
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
1 DA TB2 DB
2 DB TB3 DG
3 DG TB4 SLD
Insulation
4 SLD TB5 +24V
5 +24V TB6 (FG)
6 FG TB7 24G
7 24G
Module power supply TB8 X0
TB9 COM+
Black
3-wire sensor 8 X0 TB10 X1
Brown 9 COM+ TB11 COM-
Blue 10 X1
TB12 X2
11 COM-
TB13 COM+
12 X2
13 COM+ TB14 X3
14 X3 TB15 COM-
15 COM- TB16 Y8
Load
16 Y8 TB17 COM+
17 COM+ TB18 Y9
18 Y9 TB19 COM+
19 COM+
TB20 YA
20 YA
21 COM+
TB21 COM+
Load TB22 YB
22 YB
23 COM+ TB23 COM+
24 DC24V TB24 DC24V
25 DC24G TB25 DC24G
External power supply
for output part

Constant-voltage circuit

6-4 6-4
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.1.3 AJ65SBTB1-16DT combined module

Type DC input transistor output combined module
Item AJ65SBTB1-16DT Appearance
Input Output
Number of input points 8 points Number of output points 8 points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 24VDC
Operating load voltage 19.2 to 26.4VDC
Rated input current Approx. 7mA
range (ripple ratio: within 5%)
19.2 to 26.4VDC
Operating voltage range Max. load current 0.5A/point, 2.4A/common
(ripple ratio: within 5%)
Max. number of simultaneous
100% Max. inrush current 1.0A, 10ms or less
input points
14VDC or higher/3.5mA or
ON voltage/ON current Leakage current at OFF 0.25mA or lower
higher
0.3VDC or lower (TYP.) 0.5A,
OFF voltage/OFF current 6VDC or lower/1.7mA or lower Max. voltage drop at ON
0.6VDC or lower (MAX.) 0.5A
Output type Sink type
Input resistance Approx. 3.3kΩ Overload protection, overvoltage
Protection function
protection, overheat protection
OFF→ON 1.5ms or less (at 24VDC) Response OFF→ON 0.5ms or less
Response time
ON→OFF 1.5ms or less (at 24VDC) time ON→OFF 1.5ms or less (resistive load)

YF COM-
YE COM+
B RATE
40 20 10 8 4 2 1 4 2 1
19.2 to 26.4VDC
External Voltage
(ripple ratio: within 5%)

YD
STATION NO.
power supply

YC
17.8mA or lower

YB
for output
Current (at 24VDC and all points ON),

YA
part

Y9
excluding external load current

ON

Y8
X7
Input type Positive common (sink type) Surge suppressor Zener diode

X6
Y8 9 A B C D E F

X5
Wiring method for common 16 points/common (1-wire, terminal block type )

X4
AJ65SBTB1-16DT

X3
Number of occupied stations 32-point assignment/station (16 points used)

X2
X1
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

X0
X0 1 2 3 4 5 6 7
supply Current 50mA or lower (at 24VDC and all points ON)
Noise voltage 500Vp-p, noise width 1µs,

(FG)
24G
Noise immunity
noise frequency 25 to 60Hz (DC type noise simulator condition)

+24V
SLD
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
DA DG
10MΩ or higher between all DC external terminals and ground (500VDC insulation resistance DB
Insulation resistance
tester)
Protection degree IP2X
Weight 0.18kg
7-point two-piece terminal block
Communication part,
[Transmission circuit, module power supply, FG]
module power supply
M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
External part
Applicable solderless terminal: 2 or less
connection
18-point direct-mount terminal block
system I/O power supply
[I/O power supply, I/O signal]
part,
M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
I/O part
Applicable solderless terminal: 2 or less
M4 screw with plain washer finished round (tightening torque range: 0.78 to 1.08N•m)
Module mounting screw
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

6-5 6-5
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
TB2 DB
1 DA
TB3 DG
2 DB
3 DG TB4 SLD
Insulation
4 SLD TB5 +24V
5 +24V TB6 (FG)
6 FG TB7 24G
7 24G TB8 X0
Module power supply
TB9 X1
8 X0 TB10 X2
9 X1 TB11 X3
10 X2 TB12 X4
11 X3
TB13 X5
12 X4
13 X5
TB14 X6
14 X6 TB15 X7
15 X7 TB16 Y8
Load
16 Y8 TB17 Y9
17 Y9 TB18 YA
18 YA
TB19 YB
19 YB
TB20 YC
20 YC
21 YD TB21 YD
22 YE TB22 YE
Load
23 YF TB23 YF
TB24 COM+
TB25 COM-

24 COM+
External power supply
25 COM-
for output part Constant-voltage circuit
Load power supply

Load
External power supply for output part
24 COM+
and load power supply (common)
25 COM-

6-6 6-6
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.1.4 AJ65SBTB1-16DT1 combined module

Type DC input transistor output combined module
Item AJ65SBTB1-16DT1 Appearance
Input Output
Number of input points 8 points Number of output points 8 points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 24VDC
Operating load voltage 19.2 to 26.4VDC
Rated input current Approx. 5mA
range (ripple ratio: within 5%)
19.2 to 26.4VDC
Operating voltage range Max. load current 0.5A/point, 2.4A/common
(ripple ratio: within 5%)
Max. number of simultaneous
100% Max. inrush current 1.0A, 10ms or less
input points
ON voltage/ON current 15VDC or higher/3mA or higher Leakage current at OFF 0.25mA or lower
0.3VDC or lower (TYP.) 0.5A,
OFF voltage/OFF current 3VDC or lower/0.5mA or lower Max. voltage drop at ON
0.6VDC or lower (MAX.) 0.5A
Output type Sink type
Input resistance Approx. 4.7kΩ Overload protection, overvoltage
Protection function
protection, overheat protection
OFF→ON 0.2ms or less (at 24VDC) Response OFF→ON 0.5ms or less
Response time
ON→OFF 0.2ms or less (at 24VDC) time ON→OFF 1.5ms or less (resistive load)

YF COM-
YE COM+
19.2 to 26.4VDC

B RATE
40 20 10 8 4 2 1 4 2 1
External Voltage
(ripple ratio: within 5%)
power

YD
STATION NO.
17.8mA or lower

YC
supply for

YB
Current (at 24VDC and all points ON),
output part

YA
Y9
excluding external load current

ON

Y8
Input type Positive common (sink type) Surge suppressor Zener diode

X7
X6
Y8 9 A B C D E F
Wiring method for common 16 points/common (1-wire, terminal block type)

X5
X4
AJ65SBTB1-16DT1
Number of occupied stations 32-point assignment/station (16 points used)

X3
X2
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

X1
supply

X0
Current 55mA or lower (at 24VDC and all points ON)

X0 1 2 3 4 5 6 7
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity

(FG)
24G
noise frequency 25 to 60Hz (DC type noise simulator condition)

+24V
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

SLD
DA DG
10MΩ or higher between all DC external terminals and ground (500VDC insulation resistance
Insulation resistance
DB
tester)
Protection degree IP2X
Weight 0.18kg
Communication 7-point two-piece terminal block
part, [Transmission circuit, module power supply, FG]
module power M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
External
supply part Applicable solderless terminal: 2 or less
connection
18-point direct-mount terminal block
system I/O power supply
[I/O power supply, I/O signal]
part,
M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
I/O part
Applicable solderless terminal: 2 or less
M4 screw with plain washer finished round (tightening torque range: 0.78 to 1.08N•m)
Module mounting screw
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

6-7 6-7
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
1 DA TB2 DB
2 DB TB3 DG
3 DG Insulation TB4 SLD
4 SLD TB5 +24V
5 +24V TB6 (FG)
6 FG TB7 24G
7 24G
Module power supply TB8 X0
TB9 X1
8 X0 TB10 X2
9 X1 TB11 X3
10 X2
TB12 X4
11 X3
TB13 X5
12 X4
13 X5 TB14 X6
14 X6 TB15 X7
Load
15 X7 TB16 Y8
16 Y8 TB17 Y9
17 Y9 TB18 YA
18 YA TB19 YB
19 YB
TB20 YC
20 YC
21 YD
TB21 YD
22 YE TB22 YE
Load
23 YF TB23 YF
TB24 COM+
TB25 COM-

24 COM+
External power supply 25 COM-
for output part Constant-voltage circuit
Load power supply

Load
External power supply for output part
24 COM+
and load power supply (common)
25 COM-

6-8 6-8
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.1.5 AJ65SBTB1-16DT2 combined module

Type DC input transistor output combined module
Item AJ65SBTB1-16DT2 Appearance
Input Output
Number of input points 8 points Number of output points 8 points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 24VDC
Operating load voltage 19.2 to 26.4VDC
Rated input current Approx. 7mA
range (ripple ratio: within 5%)
19.2 to 26.4VDC
Operating voltage range Max. load current 0.5A/point, 2.4A/common
(ripple ratio: within 5%)
Max. number of simultaneous
100% Max. inrush current 1.0A, 10ms or less
input points
14VDC or higher/3.5mA or
ON voltage/ON current Leakage current at OFF 0.1mA or lower
higher
0.3VDC or lower (TYP.) 0.5A,
OFF voltage/OFF current 6VDC or lower/1.7mA or lower Max. voltage drop at ON
0.6VDC or lower (MAX.) 0.5A
Output type Sink type
Input resistance Approx. 3.3kΩ
Protection function None
OFF→ON 1.5ms or less (at 24VDC) Response OFF→ON 0.5ms or less
Response time
ON→OFF 1.5ms or less (at 24VDC) time ON→OFF 1.5ms or less (resistive load)

COM-
COM+
External Voltage 19.2 to 26.4VDC

B RATE
40 20 10 8 4 2 1 4 2 1

YF
power supply (ripple ratio: within 5%)

YE
YD
STATION NO.
for output Current 17.8mA or lower

YC
YB
part (at 24VDC and all points ON),

YA
Y9
excluding external load current

ON

Y8
Input type Positive common (sink type) Surge suppressor Zener diode

X7
X6
Y8 9 A B C D E F
Wiring method for common 16 points/common (1-wire, terminal block type)

X5
X4
AJ65SBTB1-16DT2
Number of occupied stations 32-point assignment/station (16 points used)

X3
X2
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

X1
supply

X0
Current 50mA or lower (at 24VDC and all points ON)

X0 1 2 3 4 5 6 7
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity

(FG)
24G
noise frequency 25 to 60Hz (DC type noise simulator condition)

+24V
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

SLD
DA DG
10MΩ or higher between all DC external terminals and ground (500VDC insulation resistance
Insulation resistance
tester) DB

Protection degree IP2X

Weight 0.18kg
7-point two-piece terminal block
Communication
[Transmission circuit, module power supply, FG]
part, module power
M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
External supply part
Applicable solderless terminal: 2 or less
connection
18-point direct-mount terminal block
system I/O power supply
[I/O power supply, I/O signal]
part,
M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
I/O part
Applicable solderless terminal: 2 or less
M4 screw with plain washer finished round (tightening torque range: 0.78 to 1.08N•m)
Module mounting screw
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

6-9 6-9
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
1
TB2 DB
DA
2 DB TB3 DG
3 DG TB4 SLD
Insulation
4 SLD TB5 +24V
5 +24V TB6 (FG)
6 FG TB7 24G
7 24G
Module power supply TB8 X0
TB9 X1
8 X0 TB10 X2
9 X1 TB11 X3
10 X2
TB12 X4
11 X3
TB13 X5
12 X4
13 X5
TB14 X6
14 X6 TB15 X7
15 X7 TB16 Y8
Load
16 Y8 TB17 Y9
17 Y9 TB18 YA
18 YA TB19 YB
19 YB
TB20 YC
20 YC
21 YD
TB21 YD
22 YE TB22 YE
Load
23 YF TB23 YF
TB24 COM+
TB25 COM-

24 COM+
External power supply
25 COM-
for output part Constant-voltage circuit
Load power supply

Load
External power supply for output part
24 COM + and load power supply (common)
25 COM-

6 - 10 6 - 10
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.1.6 AJ65SBTB1-16DT3 combined module

Type DC input transistor output combined module
Item AJ65SBTB1-16DT3 Appearance
Input Output
Number of input points 8 points Number of output points 8 points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 24VDC
Operating load voltage 19.2 to 26.4VDC
Rated input current Approx. 5mA
range (ripple ratio: within 5%)
19.2 to 26.4VDC
Operating voltage range Max. load current 0.5A/point, 2.4A/common
(ripple ratio: within 5%)
Max. number of simultaneous
100% Max. inrush current 1.0A, 10ms or less
input points
ON voltage/ON current 15VDC or higher/3mA or higher Leakage current at OFF 0.1mA or lower
0.3VDC or lower (TYP.) 0.5A,
OFF voltage/OFF current 3VDC or lower/0.5mA or lower Max. voltage drop at ON
0.6VDC or lower (MAX.) 0.5A
Output type Sink type
Input resistance Approx. 4.7kΩ
Protection function None
OFF→ON 0.2ms or less (at 24VDC) OFF→ON 0.5ms or less
Response time Response time
ON→OFF 0.2ms or less (at 24VDC) ON→OFF 1.5ms or less (resistive load)

COM-
19.2 to 26.4VDC

COM+
Voltage

B RATE
40 20 10 8 4 2 1 4 2 1
External power (ripple ratio: within 5%)

YF
YE
supply for 17.8mA or lower

YD
STATION NO.

YC
output part Current (at 24VDC and all points ON),

YB
YA
excluding external load current

Y9
ON
Input type Positive common (sink type) Surge suppressor Zener diode

Y8
X7
Wiring method for common 16 points/common (1-wire, terminal block type)

X6
Y8 9 A B C D E F

X5
Number of occupied stations 32-point assignment/station (16 points used)

X4
AJ65SBTB1-16DT3

X3
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

X2
X1
supply Current 55mA or lower (at 24VDC and all points ON)

X0
X0 1 2 3 4 5 6 7
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity
noise frequency 25 to 60Hz (DC type noise simulator condition)

(FG)
24G
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

+24V
SLD
10MΩ or higher between all DC external terminals and ground (500VDC insulation resistance

DA DG
Insulation resistance
tester)

DB
Protection degree IP2X
Weight 0.18kg
7-point two-piece terminal block
Communication part,
[Transmission circuit, module power supply, FG]
module power supply
M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
External part
Applicable solderless terminal: 2 or less
connection
18-point direct-mount terminal block
system I/O power supply
[I/O power supply, I/O signal]
part,
M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
I/O part
Applicable solderless terminal: 2 or less
M4 screw with plain washer finished round (tightening torque range: 0.78 to 1.08N•m)
Module mounting screw
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

6 - 11 6 - 11
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
TB2 DB
1 DA
TB3 DG
2 DB
3 DG TB4 SLD
Insulation
4 SLD TB5 +24V
5 +24V TB6 (FG)
6 FG TB7 24G
7 24G
Module power supply TB8 X0
TB9 X1
8 X0 TB10 X2
9 X1 TB11 X3
10 X2
TB12 X4
11 X3
12 X4 TB13 X5
13 X5 TB14 X6
14 X6 TB15 X7
Load 15 X7 TB16 Y8
16 Y8
TB17 Y9
17 Y9
TB18 YA
18 YA
19 YB TB19 YB
20 YC TB20 YC
21 YD TB21 YD
Load 22 YE TB22 YE
23 YF
TB23 YF
TB24 COM+
TB25 COM-

24 COM+
External power supply 25 COM-
for output part Constant-voltage circuit
Load power supply

Load
External power supply for output part
24 COM+ and load power supply (common)
25 COM-

6 - 12 6 - 12
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.1.7 AJ65SBTB32-16DT combined module

Type DC input transistor output combined module

Item AJ65SBTB32-16DT Appearance
Input Output
Number of input points 8 points Number of output points 8 points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 24VDC
Operating load voltage 19.2 to 26.4VDC
Rated input current Approx. 7mA
range (ripple ratio: within 5%)
19.2 to 26.4VDC
Operating voltage range Max. load current 0.5A/point, 2.4A/common
(ripple ratio: within 5%)
Max. number of simultaneous
100% Max. inrush current 1.0A, 10ms or less
input points
ON voltage/ON current 14VDC or higher/3.5mA or higher Leakage current at OFF 0.25mA or lower
0.3VDC or lower (TYP.) 0.5A,
OFF voltage/OFF current 6VDC or lower/1.7mA or lower Max. voltage drop at ON
0.6VDC or lower (MAX.) 0.5A
Output type Sink type
Input resistance Approx. 3.3kΩ Overload protection, overvoltage
Protection function

COM+ COM- COM+ COM- COM+ COM- COM+ COM- COM+ COM+ COM+ COM+ COM+ COM+ COM+ COM+ DC24G
protection, overheat protection

DC24V
B RATE
40 20 10 8 4 2 1 4 2 1
OFF→ON 1.5ms or less (at 24VDC) Response OFF→ON 0.5ms or less

YF
Response time

STATION NO.
ON→OFF 1.5ms or less (at 24VDC) time ON→OFF 1.5ms or less (resistive load)

YE
19.2 to 26.4VDC

YD
Voltage
External (ripple ratio: within 5%)

ON

YC
power supply 17.8mA or lower

YB
for output part Current (at 24VDC and all points ON),

YA
excluding external load current

Y9
Input type Positive common (sink type) Surge suppressor Zener diode

Y8
Supply current for connected
1.0A or lower/common

X7
device

X6
Wiring method for common 16 points/common (input: 3-wire terminal block type, output: 2-wire terminal block type)

X5
Number of occupied stations 32-point assignment/station (16 points used)

X4
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

X3
supply Current 50mA or lower (at 24VDC and all points ON) Y8 9 A B C D E F

X2
AJ65SBTB32-16DT
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity
X1
noise frequency 25 to 60Hz (DC type noise simulator condition) X0

Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
PW L RUN L ERR. X0 1 2 3 4 5 6 7

10MΩ or higher between all DC external terminals and ground (500VDC insulation resistance
Insulation resistance
(FG)
24G

tester)
+24V

Protection degree IP2X

SLD
DG

Weight 0.25kg
DB
DA

7-point two-piece terminal block

Communication
[Transmission circuit, module power supply, FG]
part, module
M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
External power supply part
Applicable solderless terminal: 2 or less
connection
34-point direct-mount terminal block
system I/O power supply
[I/O power supply, I/O signal]
part,
M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
I/O part
Applicable solderless terminal: 2 or less
M4 screw with plain washer finished round (tightening torque range: 0.78 to 1.08N•m)
Module mounting screw
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

6 - 13 6 - 13
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
TB2 DB
1 DA
2 DB
TB3 DG
3 DG TB4 SLD
Insulation TB5 +24V
4 SLD
5 +24V TB6 (FG)
6 FG TB7 24G
7 24G
Module power supply TB8 X0
TB9 COM+
Black
3-wire sensor 8 X0 TB10 X1
Brown
9 COM+ TB11 COM-
Blue 10 X1
TB12 X2
11 COM-
12 X2 TB13 COM+
13 COM+ TB14 X3
14 X3 TB15 COM-
15 COM- TB16 X4
16 X4 TB17 COM+
17 COM+
TB18 X5
18 X5
19 COM- TB19 COM-
20 X6 TB20 X6
21 COM+ TB21 COM+
22 X7 TB22 X7
23 COM-
Load TB23 COM-
24 Y8
TB24 Y8
25 COM+
26 Y9 TB25 COM+
27 COM+ TB26 Y9
28 YA TB27 COM+
29 COM+ TB28 YA
30 YB
TB29 COM+
31 COM+
32 YC
TB30 YB
33 COM+ TB31 COM+
34 YD TB32 YC
35 COM+ TB33 COM+
36 YE TB34 YD
37 COM+
Load TB35 COM+
38 YF
39 COM+
TB36 YE
40 DC24V TB37 COM+
41 DC24G TB38 YF
External power supply
TB39 COM+
for output part
TB40 DC24V
Constant-voltage circuit
TB41 DC24G

6 - 14 6 - 14
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.1.8 AJ65SBTB32-16DT2 combined module

Type DC input transistor output combined module

Item AJ65SBTB32-16DT2 Appearance
Input Output
Number of input points 8 points Number of output points 8 points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 24VDC
Operating load voltage 19.2 to 26.4VDC
Rated input current Approx. 7mA
range (ripple ratio: within 5%)
19.2 to 26.4VDC
Operating voltage range Max. load current 0.5A/point, 2.4A/common
(ripple ratio: within 5%)
Max. number of simultaneous
100% Max. inrush current 1.0A, 10ms or less
input points
14VDC or higher/3.5mA or
ON voltage/ON current Leakage current at OFF 0.1mA or lower
higher
0.3VDC or lower (TYP.) 0.5A,
OFF voltage/OFF current 6VDC or lower/1.7mA or lower Max. voltage drop at ON
0.6VDC or lower (MAX.) 0.5A
Output type Sink type
Input resistance Approx. 3.3kΩ

COM+ COM- COM+ COM- COM+ COM- COM+ COM- COM+ COM+ COM+ COM+ COM+ COM+ COM+ COM+ DC24G
Protection function None

DC24V
B RATE
40 20 10 8 4 2 1 4 2 1
OFF→ON 1.5ms or less (at 24VDC) Response OFF→ON 0.5ms or less

YF
Response time

STATION NO.
ON→OFF 1.5ms or less (at 24VDC) time ON→OFF 1.5ms or less (resistive load)

YE
19.2 to 26.4VDC

YD
Voltage
External (ripple ratio: within 5%)

ON

YC
power supply 17.8mA or lower

YB
for output part Current (at 24VDC and all points ON),

YA
excluding external load current

Y9
Input type Positive common (sink type) Surge suppressor Zener diode

Y8
Supply current for connected
1.0A or lower/common

X7
device

X6
Wiring method for common 16 points/common (input: 3-wire terminal block type, output: 2-wire terminal block type)

X5
Number of occupied stations 32-point assignment/station (16 points used)

X4
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

X3
supply Current 50mA or lower (at 24VDC and all points ON) Y8 9 A B C D E F

AJ65SBTB32-16DT2
X2
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity
X1
noise frequency 25 to 60Hz (DC type noise simulator condition) X0

Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
PW L RUN L ERR. X0 1 2 3 4 5 6 7

10MΩ or higher between all DC external terminals and ground (500VDC insulation resistance
Insulation resistance
(FG)
24G

tester)
+24V

Protection degree IP2X

SLD
DG

Weight 0.25kg
DB
DA

7-point two-piece terminal block

Communication
[Transmission circuit, module power supply, FG]
part, module
M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
External power supply part
Applicable solderless terminal: 2 or less
connection
34-point direct-mount terminal block
system I/O power supply
[I/O power supply, I/O signal]
part,
M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
I/O part
Applicable solderless terminal: 2 or less
M4 screw with plain washer finished round (tightening torque range: 0.78 to 1.08N•m)
Module mounting screw
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

6 - 15 6 - 15
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
TB2 DB
1 DA TB3 DG
2 DB TB4 SLD
3 DG Insulation TB5 +24V
4 SLD
TB6 (FG)
5 +24V
6 FG
TB7 24G
7 24G TB8 X0
Module power supply TB9 COM+
Black TB10 X1
3-wire sensor 8 X0
Brown TB11 COM-
9 COM+
Blue TB12 X2
10 X1
11 COM- TB13 COM+
12 X2 TB14 X3
13 COM+
TB15 COM-
14 X3
15 COM-
TB16 X4
16 X4 TB17 COM+
17 COM+ TB18 X5
18 X5 TB19 COM-
19 COM- TB20 X6
20 X6
TB21 COM+
21 COM+
22 X7 TB22 X7
Load 23 COM- TB23 COM-
24 Y8 TB24 Y8
25 COM+ TB25 COM+
26 Y9
TB26 Y9
27 COM+
28 YA
TB27 COM+
29 COM+ TB28 YA
30 YB TB29 COM+
31 COM+ TB30 YB
32 YC TB31 COM+
33 COM+
TB32 YC
34 YD
35 COM+ TB33 COM+
36 YE TB34 YD
Load 37 COM+ TB35 COM+
38 YF TB36 YE
39 COM+
TB37 COM+
40 DC24V
41 DC24G
TB38 YF
External power supply Constant-voltage circuit TB39 COM+
for output part TB40 DC24V
TB41 DC24G

6 - 16 6 - 16
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.1.9 AJ65SBTB32-16KDT2 combined module

Type DC input transistor output combined module

Item AJ65SBTB32-16KDT2 Appearance
Input Output
Number of input points 8 points Number of output points 8 points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 24VDC
Operating load voltage 20.4 to 28.8VDC
Rated input current Approx. 7mA
range (ripple ratio: within 5%)
20.4 to 28.8VDC
Operating voltage range Max. load current 0.5A/point, 2.4A/common
(ripple ratio: within 5%)
Max. number of simultaneous
100% Max. inrush current 1.0A, 10ms or less
input points
14VDC or higher/4mA or
ON voltage/ON current Leakage current at OFF 0.1mA or lower
higher
5.5VDC or lower/1.7mA or 0.3VDC or lower (TYP.) 0.5A,
OFF voltage/OFF current Max. voltage drop at ON
lower 0.6VDC or lower (MAX.) 0.5A
Output type Sink type
Input resistance Approx. 3.0kΩ
Protection function None
Input response
0.2ms 1.5ms 5ms 10ms
speed
OFF→ON 0.5ms or less
0.2ms 1.5ms 5ms or 10ms Response
Response time OFF→ON
or less or less less or less time
0.2ms 1.5ms 5ms or 10ms
ON→OFF ON→OFF 1.5ms or less (resistive load)
or less or less less or less
19.2 to 28.8VDC
External Voltage
(ripple ratio: within 5%)
power
10mA or lower
supply for
Current (at 24VDC and all points ON),
output part
excluding external load current
Input type Positive common (sink type) Surge suppressor Zener diode
Supply current for connected
1.0A or lower/common
device
Wiring method for common 16 points/common (input: 3-wire terminal block type, output: 2-wire terminal block type)
Number of occupied stations 32-point assignment/station (16 points used)
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
supply Current 55mA or lower (at 24VDC and all points ON)
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity
noise frequency 25 to 60Hz (DC type noise simulator condition)
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
10MΩ or higher between all DC external terminals and ground (500VDC insulation
Insulation resistance
resistance tester)
Protection degree IP2X
Weight 0.26kg
7-point two-piece terminal block
Communication part,
[Transmission circuit, module power supply, FG]
module power supply
M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
External part
Applicable solderless terminal: 2 or less
connection
34-point direct-mount terminal block
system
I/O power supply part, [I/O power supply, I/O signal]
I/O part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
M4 screw with plain washer finished round (tightening torque range: 0.78 to 1.08N•m)
Module mounting screw
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

6 - 17 6 - 17
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
TB2 DB
TB3 DG
TB4 SLD
1 DA
2 DB
TB5 +24V
3 DG TB6 (FG)
Insulation
4 SLD TB7 24G
5 +24V
TB8 X0
6 FG
7 24G TB9 COM+
Module power supply
TB10 X1
Black TB11 COM-
3-wire sensor 8 X0 TB12 X2
Brown
9 COM+
Blue TB13 COM+
10 X1
Blue 11 COM- TB14 X3
2-wire sensor
Brown 12 X2 TB15 COM-
13 COM+
14 X3
TB16 X4
15 COM- TB17 COM+
16 X4 TB18 X5
17 COM+
TB19 COM-
18 X5
19 COM- TB20 X6
20 X6 TB21 COM+
21 COM+
TB22 X7
22 X7
23 COM- TB23 COM-
Load
24 Y8 TB24 Y8
25 COM+ TB25 COM+
26 Y9
27 COM+
TB26 Y9
28 YA TB27 COM+
29 COM+ TB28 YA
30 YB
TB29 COM+
31 COM+
32 YC TB30 YB
33 COM+ TB31 COM+
34 YD
TB32 YC
35 COM+
36 YE TB33 COM+
Load 37 COM+ TB34 YD
38 YF TB35 COM+
39 COM+
External power supply TB36 YE
40 DC24V
for output part
41 DC24G TB37 COM+
Constant-voltage circuit
TB38 YF
TB39 COM+
TB40 DC24V
TB41 DC24G

6 - 18 6 - 18
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.1.10 AJ65SBTB32-16KDT8 combined module

Type DC input transistor output combined module

Item AJ65SBTB32-16KDT8 Appearance
Input Output
Number of input points 8 points Number of output points 8 points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 12VDC Rated load voltage 12VDC
Operating load voltage 10.2 to 14.4VDC
Rated input current Approx. 11mA
range (ripple ratio: within 5%)
10.2 to 14.4VDC
Operating voltage range Max. load current 0.5A/point, 2.4A/common
(ripple ratio: within 5%)
Max. number of simultaneous
100% Max. inrush current 1.0A, 10ms or less
input points
ON voltage/ON current 5.6VDC or higher/4mA or higher Leakage current at OFF 0.1mA or lower
0.3VDC or lower (TYP.) 0.5A,
OFF voltage/OFF current 2.4VDC or lower/1.7mA or lower Max. voltage drop at ON
0.6VDC or lower (MAX.) 0.5A
Output type Sink type
Input resistance Approx. 1.0kΩ
Protection function None
Input response
0.2ms 1.5ms 5ms 10ms
speed
OFF→ON 0.5ms or less
0.2ms 1.5ms 5ms or 10ms Response
Response time OFF→ON
or less or less less or less time
0.2ms 1.5ms 5ms or 10ms
ON→OFF ON→OFF 1.5ms or less (resistive load)
or less or less less or less
10.2 to 14.4VDC
External Voltage
(ripple ratio: within 5%)
power
10mA or lower
supply for
Current (at 12VDC and all points ON),
output part
excluding external load current
Input type Positive common (sink type) Surge suppressor Zener diode
Supply current for connected
1.0A or lower/common
device
Wiring method for common 16 points/common (input: 3-wire terminal block type, output: 2-wire terminal block type)
Number of occupied stations 32-point assignment/station (16 points used)
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
supply Current 55mA or lower (at 24VDC and all points ON)
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity
noise frequency 25 to 60Hz (DC type noise simulator condition)
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
10MΩ or higher between all DC external terminals and ground (500VDC insulation resistance
Insulation resistance
tester)
Protection degree IP2X
Weight 0.26kg
Communication
7-point two-piece terminal block [Transmission circuit, module power supply, FG]
part,
M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
External module power
Applicable solderless terminal: 2 or less
connection supply part
system I/O power supply 34-point direct-mount terminal block [I/O power supply, I/O signal]
part, M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
I/O part Applicable solderless terminal: 2 or less
M4 screw with plain washer finished round (tightening torque range: 0.78 to 1.08N•m)
Module mounting screw
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

6 - 19 6 - 19
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
TB2 DB
TB3 DG
1 DA TB4 SLD
2 DB TB5 +24V
3 DG Insulation TB6 (FG)
4 SLD
5 +24V TB7 24G
6 FG TB8 X0
7 24G TB9 COM+
Module power supply
TB10 X1
Black TB11 COM-
3-wire sensor 8 X0
Brown TB12 X2
9 COM+
Blue
10 X1 TB13 COM+
Blue 11 COM-
2-wire sensor TB14 X3
Brown 12 X2
13 COM+ TB15 COM-
14 X3 TB16 X4
15 COM-
TB17 COM+
16 X4
17 COM+ TB18 X5
18 X5 TB19 COM-
19 COM- TB20 X6
20 X6
21 COM+
TB21 COM+
22 X7 TB22 X7
Load
23 COM- TB23 COM-
24 Y8
TB24 Y8
25 COM+
26 Y9 TB25 COM+
27 COM+ TB26 Y9
28 YA
TB27 COM+
29 COM+
30 YB TB28 YA
31 COM+ TB29 COM+
32 YC TB30 YB
33 COM+
34 YD
TB31 COM+
35 COM+ TB32 YC
36 YE TB33 COM+
37 COM+
Load TB34 YD
38 YF
39 COM+ TB35 COM+
External power supply for 40 DC12V TB36 YE
output part 41 DC12G
Constant-voltage circuit TB37 COM+
TB38 YF
TB39 COM+
TB40 DC12V
TB41 DC12G

6 - 20 6 - 20
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.1.11 AJ65SBTB32-16DR combined module

Type DC input contact output combined module

Item AJ65SBTB32-16DR Appearance
Input Output
Number of output
Number of input points 8 points 8 points
points
Isolation method Photocoupler Isolation method Relay
2A/point, 4A/common
Rated input voltage 24VDC Rated load voltage at 24VDC (resistive load) or 240VAC
(cosφ=1)
Number of
Rated input current Approx. 7mA simultaneous ON All points
points
19.2 to 26.4VDC
Operating voltage range Min. switching load 5VDC, 1mA
(ripple ratio: within 5%)
Max. number of
100% Max. switching voltage 264VAC, 125VDC
simultaneous input points
Mechanical 20 million times or more
14VDC or higher/3.5mA or Rated switching voltage/current load:
ON voltage/ON current 100 thousand times or more
higher
200VAC 1.5A, 240VAC 1A (cosφ=0.7):
Life 100 thousand times or more
Electrical
200VAC 1A, 240VAC 0.5A (cosφ=0.35):
6VDC or lower/1.7mA or 100 thousand times or more
OFF voltage/OFF current
lower 24VDC 1A, 100VDC 0.1A (L/R=7ms):
100 thousand times or more
Max. switching
Input resistance Approx. 3.3kΩ 3600 times/hour
frequency
OFF→ON 1.5ms or less (at 24VDC) Response OFF→ON 10ms or less
Response time
ON→OFF 1.5ms or less (at 24VDC) time ON→OFF 12ms or less
8 points/common Wiring method for 4 points/common
Wiring method for common
(3-wire, terminal block type) common (2-wire, terminal block type)
Positive/negative common
Input type shared type Surge suppressor None
(sink/source shared type)
Supply current for connected
1.0A or lower/common
device
Number of occupied stations 32-point assignment/station (16 points used)
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
supply Current 85mA or lower (at 24VDC and all points ON)
Noise voltage: 1500Vp-p (AC type), 500Vp-p (DC type), noise width 1µs,
Noise immunity
noise frequency 25 to 60Hz (noise simulator condition)
2830VACrms for 3 cycles between all AC external terminals and ground (2000m above sea
Withstand voltage level)
500VAC for 1 minute between all DC external terminals and ground
10MΩ or higher between all AC external terminals and ground (500VDC insulation resistance
tester)
Insulation resistance
10MΩ or higher between all DC external terminals and ground (500VDC insulation resistance
tester)
Protection degree IP1X
Weight 0.28kg
Communication
7-point two-piece terminal block [Transmission circuit, module power supply, FG]
part,
M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
External module power
Applicable solderless terminal: 2 or less
connection supply part
system I/O power supply 34-point direct-mount terminal block [I/O power supply, I/O signal]
part, M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
I/O part Applicable solderless terminal: 2 or less
M4 screw with plain washer finished round (tightening torque range: 0.78 to 1.08N•m)
Module mounting screw
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
Applicable solderless [Applicable wire size: 0.3 to 1.25mm2]
terminal y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

6 - 21 6 - 21
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
TB2 DB
TB3 DG
1 DA
TB4 SLD
2 DB
3 DG TB5 +24V
Insulation
4 SLD TB6 (FG)
5 +24V
TB7 24G
6 FG
7 24G TB8 X0
Module power supply TB9 COM1A
TB10 X1
Black TB11 COM1B
3-wire sensor 8 X0
Brown TB12 X2
9 COM1A
Blue
10 X1 TB13 COM1A
2-wire sensor Blue 11 COM1B TB14 X3
Brown 12 X2
TB15 COM1B
13 COM1A
14 X3 TB16 X4
15 COM1B TB17 COM1A
16 X4
TB18 X5
17 COM1A
18 X5 TB19 COM1B
19 COM1B TB20 X6
20 X6 TB21 COM1A
21 COM1A
22 X7
TB22 X7
23 COM1B TB23 COM1B
24 DC24A TB24 DC24A
25 DC24B
Load TB25 DC24B
26 Y8
27 COM2B TB26 Y8
Load
28 Y9 TB27 COM2B
29 COM2B
Load TB28 Y9
30 YA
31 COM2B TB29 COM2B
Load
External power supply 32 YB TB30 YA
for output part 33 COM2A
Load TB31 COM2B
34 YC
35 COM3B
TB32 YB
Load
36 YD TB33 COM2A
37 COM3B TB34 YC
Load
38 YE
TB35 COM3B
39 COM3B
Load
External power supply 40 YF TB36 YD
for output part 41 COM3A TB37 COM3B
TB38 YE
TB39 COM3B
TB40 YF
TB41 COM3A

6 - 22 6 - 22
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.1.12 AJ65SBTB32-16KDR combined module

Type DC input contact output combined module

Item AJ65SBTB32-16KDR Appearance
Input Output
Number of input points 8 points Number of output points 8 points
Isolation method Photocoupler Isolation method Relay
2A/point, 4A/common
Rated input voltage 24VDC Rated load voltage at 24VDC (resistive load) or 240VAC
(cosφ=1)
Number of simultaneous
Rated input current Approx. 7mA All points
ON points
20.4 to 28.8VDC
Operating voltage range Min. switching load 5VDC, 1mA
(ripple ratio: within 5%)
Max. number of
100% Max. switching voltage 264VAC, 125VDC
simultaneous input points
ON voltage/ON current 14VDC or higher/4mA or higher Mechanical 20 million times or more
Rated switching voltage/current load:
OFF voltage/OFF current 5.5VDC or lower/1.7mA or lower
100 thousand times or more
Input resistance Approx. 3.0kΩ 200VAC 1.5A, 240VAC 1A (cosφ=0.7):
Life 100 thousand times or more
Input response Electrical
0.2ms 1.5ms 5ms 10ms 200VAC 1A, 240VAC 0.5A (cosφ=0.35):
speed 100 thousand times or more
Response 0.2ms 1.5ms 5ms or 10ms 24VDC 1A, 100VDC 0.1A (L/R=7ms):
OFF→ON
time or less or less less or less 100 thousand times or more
0.2ms 1.5ms 5ms or 10ms Max. switching
ON→OFF 3600 times/hour
or less or less less or less frequency
8 points/common
Wiring method for common OFF→ON 10ms or less
(3-wire, terminal block type)
Response
Positive/negative common
time
Input type shared type ON→OFF 12ms or less
(sink/source shared type)
Wiring method for 4 points/common
Supply current for connected common (2-wire, terminal block type)
1.0A or lower/common
device
Surge suppressor None

Number of occupied stations 32-point assignment/station (16 points used)

Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
supply Current 100mA or lower (at 24VDC and all points ON)
Noise voltage: 1500Vp-p (AC type), 500Vp-p (DC type), noise width 1µs,
Noise immunity
noise frequency 25 to 60Hz (noise simulator condition)
2830VACrms for 3 cycles between all AC external terminals and ground (2000m above sea level)
Withstand voltage
500VAC for 1 minute between all DC external terminals and ground
10MΩ or higher between all AC external terminals and ground (500VDC insulation resistance tester)
Insulation resistance
10MΩ or higher between all DC external terminals and ground (500VDC insulation resistance tester)
Protection degree IP1X
Weight 0.29kg
Communication
7-point two-piece terminal block [Transmission circuit, module power supply, FG]
part,
M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
External module power
Applicable solderless terminal: 2 or less
connection supply part
system I/O power supply 34-point direct-mount terminal block [I/O power supply, I/O signal]
part, M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
I/O part Applicable solderless terminal: 2 or less
M4 screw with plain washer finished round (tightening torque range: 0.78 to 1.08N•m)
Module mounting screw
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
2
Applicable solderless [Applicable wire size: 0.3 to 1.25mm ]
terminal y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

6 - 23 6 - 23
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
TB2 DB
1 DA
TB3 DG
2 DB
TB4 SLD
3 DG Insulation
4 SLD TB5 +24V
5 +24V TB6 (FG)
6 FG TB7 24G
7 24G
Module power supply TB8 X0
TB9 COM1A
TB10 X1
Black
3-wire sensor 8 X0 TB11 COM1B
Brown
Blue
9 COM1A TB12 X2
10 X1
TB13 COM1A
Blue 11 COM1B
2-wire sensor TB14 X3
Brown 12 X2
13 COM1A TB15 COM1B
14 X3 TB16 X4
15 COM1B
TB17 COM1A
16 X4
TB18 X5
17 COM1A
18 X5 TB19 COM1B
19 COM1B TB20 X6
20 X6 TB21 COM1A
21 COM1A
TB22 X7
22 X7
23 COM1B TB23 COM1B
24 DC24A TB24 DC24A
25 DC24B TB25 DC24B
Load
26 Y8
TB26 Y8
27 COM2B
Load TB27 COM2B
28 Y9
29 COM2B TB28 Y9
Load
30 YA TB29 COM2B
31 COM2B
External power supply Load TB30 YA
32 YB
for output part TB31 COM2B
33 COM2A
Load
34 YC TB32 YB
35 COM3B TB33 COM2A
Load
36 YD
TB34 YC
37 COM3B
Load TB35 COM3B
38 YE
39 COM3B TB36 YD
Load
External power supply 40 YF TB37 COM3B
41 COM3A TB38 YE
for output part
TB39 COM3B
TB40 YF
TB41 COM3A

6 - 24 6 - 24
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.1.13 AJ65SBTB1-32DT combined module

Type DC input transistor output combined module

Item AJ65SBTB1-32DT Appearance
Input Output
Number of input points 16 points Number of output points 16 points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 24VDC
Operating load voltage 19.2 to 26.4VDC
Rated input current Approx. 7mA
range (ripple ratio: within 5%)
19.2 to 26.4VDC
Operating voltage range Max. load current 0.5A/point, 3.6A/common
(ripple ratio: within 5%)
Max. number of simultaneous
100% Max. inrush current 1.0A, 10ms or less
input points
ON voltage/ON current 14VDC or higher/3.5mA or higher Leakage current at OFF 0.25mA or lower
0.3VDC or lower (TYP.) 0.5A,
OFF voltage/OFF current 6VDC or lower/1.7mA or lower Max. voltage drop at ON
0.6VDC or lower (MAX.) 0.5A
Output type Sink type
Input resistance Approx. 3.3kΩ Overload protection, overvoltage

Y1F COM-
Protection function

Y1E COM+
B RATE
40 20 10 8 4 2 1 4 2 1
protection, overheat protection
OFF→ON 1.5ms or less (at 24VDC) OFF→ON 0.5ms or less

Y1D
STATION NO.

Y1C
Response time Response time

Y1B
ON→OFF 1.5ms or less (at 24VDC) ON→OFF 1.5ms or less (resistive load)

Y1A
Y19
19.2 to 26.4VDC

Y18
ON
External power Voltage

Y17
(ripple ratio: within 5%)

Y16
supply for

Y15
30mA or lower (24VDC/common),

Y14
output part Current

Y13
excluding external load current

Y12
Y18 19 1A1B 1C1D1E 1F

Y11
Input type Positive common (sink type) Surge suppressor Zener diode

Y10
XF
Wiring method for common 32 points/common (1-wire, terminal block type)

XE
XD
Number of occupied stations 32-point assignment/station (32 points used)

XC
Y10 11 12 13 14 15 16 17

XB
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

XA
X9
supply Current 60mA or lower (at 24VDC and all points ON)

X8
X7
Noise voltage 500Vp-p, noise width 1µs,

X6
X8 9 A B C D E F

X5
Noise immunity
noise frequency 25 to 60Hz (DC type noise simulator condition)

X4
AJ65SBTB1-32DT

X3
X2
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

X1
X0
10MΩ or higher between all DC external terminals and ground (500VDC insulation resistance
PW L RUN L ERR. X0 1 2 3 4 5 6 7

Insulation resistance
tester)
(FG)
24G

Protection degree IP2X

DA DG +24V
SLD

Weight 0.25kg
DB

Communication 7-point two-piece terminal block

part, [Transmission circuit, module power supply, FG]
module power M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
External
supply part Applicable solderless terminal: 2 or less
connection
34-point direct-mount terminal block
system I/O power supply
[I/O power supply, I/O signal]
part,
M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
I/O part
Applicable solderless terminal: 2 or less
M4 screw with plain washer finished round (tightening torque range: 0.78 to 1.08N•m)
Module mounting screw
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

6 - 25 6 - 25
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
TB2 DB
1 DA
2 DB
TB3 DG
3 DG TB4 SLD
Insulation
4 SLD TB5 +24V
5 +24V TB6 (FG)
6 FG TB7 24G
7 24G TB8 X0
Module power supply
TB9 X1
8 X0
TB10 X2
9 X1
10 X2 TB11 X3
11 X3 TB12 X4
12 X4 TB13 X5
13 X5 TB14 X6
14 X6 TB15 X7
15 X7
TB16 X8
16 X8
17 X9
TB17 X9
18 XA TB18 XA
19 XB TB19 XB
20 XC TB20 XC
21 XD TB21 XD
22 XE TB22 XE
23 XF
Load TB23 XF
24 Y10
25 Y11
TB24 Y10
26 Y12 TB25 Y11
27 Y13 TB26 Y12
28 Y14 TB27 Y13
29 Y15 TB28 Y14
30 Y16 TB29 Y15
31 Y17
TB30 Y16
32 Y18
33 Y19
TB31 Y17
34 Y1A TB32 Y18
35 Y1B TB33 Y19
36 Y1C TB34 Y1A
Load
37 Y1D TB35 Y1B
38 Y1E TB36 Y1C
39 Y1F
TB37 Y1D
40 COM+
External power supply 41 COM-
TB38 Y1E
for output part TB39 Y1F
Load power supply Constant-voltage circuit TB40 COM+
TB41 COM-
Load
External power supply for output part
40 COM+ and load power supply (common)
41 COM-

6 - 26 6 - 26
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.1.14 AJ65SBTB1-32DT1 combined module

Type DC input transistor output combined module

Item AJ65SBTB1-32DT1 Appearance
Input Output
Number of input points 16 points Number of output points 16 points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 24VDC
Operating load voltage 19.2 to 26.4VDC
Rated input current Approx. 5mA
range (ripple ratio: within 5%)
19.2 to 26.4VDC
Operating voltage range Max. load current 0.5A/point, 3.6A/common
(ripple ratio: within 5%)
Max. number of simultaneous
100% Max. inrush current 1.0A, 10ms or less
input points
ON voltage/ON current 15VDC or higher/3mA or higher Leakage current at OFF 0.25mA or lower
0.3VDC or lower (TYP.) 0.5A,
OFF voltage/OFF current 3VDC or lower/0.5mA or lower Max. voltage drop at ON
0.6VDC or lower (MAX.) 0.5A
Output type Sink type
Input resistance Approx. 4.7kΩ Overload protection, overvoltage

Y1F COM-
Protection function

Y1E COM+
B RATE
40 20 10 8 4 2 1 4 2 1
protection, overheat protection

Y1D
OFF→ON 0.2ms or less (at 24VDC) Response OFF→ON 0.5ms or less

STATION NO.

Y1C
Response time

Y1B
ON→OFF 0.2ms or less (at 24VDC) time ON→OFF 1.5ms or less (resistive load)

Y1A
Y19
19.2 to 26.4VDC

Y18
External Voltage

ON

Y17
(ripple ratio: within 5%)
power

Y16
Y15
24.2mA or lower
supply for

Y14
Y13
Current (at 24VDC and all points ON),
output part

Y12
excluding external load current

Y10 11 12 13 14 15 16 17 Y18 19 1A1B 1C1D 1E 1F

Y11
Y10
Input type Positive common (sink type) Surge suppressor Zener diode

XF
XE
Wiring method for common 32 points/common (1-wire, terminal block type)

XD
XC
Number of occupied stations 32-point assignment/station (32 points used)

XB
XA
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

X9
X8
supply Current 60mA or lower (at 24VDC and all points ON)

X7
X6
X8 9 A B C D E F

X5
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity

X4
AJ65SBTB1-32DT1
noise frequency 25 to 60Hz (DC type noise simulator condition)

X3
X2
X1
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
X0
PW L RUN L ERR. X0 1 2 3 4 5 6 7

10MΩ or higher between all DC external terminals and ground (500VDC insulation resistance
Insulation resistance
tester)
(FG)
24G

Protection degree IP2X

+24V
SLD

Weight 0.25kg
DG
DB
DA

Communication 7-point two-piece terminal block

part, [Transmission circuit, module power supply, FG]
module power M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
External
supply part Applicable solderless terminal: 2 or less
connection
34-point direct-mount terminal block
system I/O power supply
[I/O power supply, I/O signal]
part,
M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
I/O part
Applicable solderless terminal: 2 or less
M4 screw with plain washer finished round (tightening torque range: 0.78 to 1.08N•m)
Module mounting screw
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

6 - 27 6 - 27
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
1 DA TB2 DB
2 DB TB3 DG
3 DG Insulation TB4 SLD
4 SLD
TB5 +24V
5 +24V
6 FG TB6 (FG)
7 24G TB7 24G
Module power supply TB8 X0
8 X0 TB9 X1
9 X1 TB10 X2
10 X2 TB11 X3
11 X3
TB12 X4
12 X4
13 X5
TB13 X5
14 X6 TB14 X6
15 X7 TB15 X7
16 X8 TB16 X8
17 X9 TB17 X9
18 XA TB18 XA
19 XB
TB19 XB
20 XC
21 XD
TB20 XC
22 XE TB21 XD
23 XF TB22 XE
Load
24 Y10 TB23 XF
25 Y11 TB24 Y10
26 Y12 TB25 Y11
27 Y13
TB26 Y12
28 Y14
29 Y15
TB27 Y13
30 Y16 TB28 Y14
31 Y17 TB29 Y15
32 Y18 TB30 Y16
33 Y19 TB31 Y17
34 Y1A TB32 Y18
35 Y1B
TB33 Y19
36 Y1C
37 Y1D
TB34 Y1A
Load
38 Y1E TB35 Y1B
39 Y1F TB36 Y1C
40 COM+ TB37 Y1D
External power supply 41 COM- TB38 Y1E
for output part
Constant-voltage circuit TB39 Y1F
Load power supply
TB40 COM+
Load
TB41 COM-
External power supply for output part
40 COM+ and load power supply (common)
41 COM-

6 - 28 6 - 28
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.1.15 AJ65SBTB1-32DT2 combined module

Type DC input transistor output combined module

Item AJ65SBTB1-32DT2 Appearance
Input Output
Number of input points 16 points Number of output points 16 points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 24VDC
Operating load voltage 19.2 to 26.4VDC
Rated input current Approx. 7mA
range (ripple ratio: within 5%)
19.2 to 26.4VDC
Operating voltage range Max. load current 0.5A/point, 3.6A/common
(ripple ratio: within 5%)
Max. number of simultaneous
100% Max. inrush current 1.0A, 10ms or less
input points
ON voltage/ON current 14VDC or higher/3.5mA or higher Leakage current at OFF 0.1mA or lower
0.3VDC or lower (TYP.) 0.5A,
OFF voltage/OFF current 6VDC or lower/1.7mA or lower Max. voltage drop at ON
0.6VDC or lower (MAX.) 0.5A
Output type Sink type
Input resistance Approx. 3.3kΩ

Y1F COM-
Protection function None

Y1E COM+
B RATE
40 20 10 8 4 2 1 4 2 1
OFF→ON 1.5ms or less (at 24VDC) OFF→ON 0.5ms or less
Response time Response time

Y1D
STATION NO.

Y1C
ON→OFF 1.5ms or less (at 24VDC) ON→OFF 1.5ms or less (resistive load)

Y1B
19.2 to 26.4VDC

Y1A
Voltage

Y19
External power (ripple ratio: within 5%)

Y18
ON

Y17
supply for 30mA or lower

Y16
Y15
output part Current (at 24VDC and all points ON),

Y14
Y13
excluding external load current

Y12
Y10 11 12 13 14 15 16 17 Y18 19 1A1B 1C1D1E 1F

Y11
Input type Positive common (sink type) Surge suppressor Zener diode

Y10
XF
Wiring method for common 32 points/common (1-wire, terminal block type)

XE
XD
Number of occupied stations 32-point assignment/station (32 points used)

XC
XB
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

XA
X9
supply Current 60mA or lower (at 24VDC and all points ON)

X8
X7
Noise voltage 500Vp-p, noise width 1µs,

X6
Noise immunity

X8 9 A B C D E F

X5
noise frequency 25 to 60Hz (DC type noise simulator condition)

X4
AJ65SBTB1-32DT2

X3
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

X2
X1
10MΩ or higher between all DC external terminals and ground (500VDC insulation resistance
X0
Insulation resistance
PW L RUN L ERR. X0 1 2 3 4 5 6 7

tester)
(FG)
24G

Protection degree IP2X

DA DG +24V

Weight 0.25kg
SLD

7-point two-piece terminal block

DB

Communication
[Transmission circuit, module power supply, FG]
part, module
M3×5.2 screw (tightening torque range:0.59 to 0.88N•m)
External power supply part
Applicable solderless terminal: 2 or less
connection
34-point direct-mount terminal block
system I/O power supply
[I/O power supply, I/O signal]
part,
M3×5.2 screw (tightening torque range:0.59 to 0.88N•m)
I/O part
Applicable solderless terminal: 2 or less
M4 screw with plain washer finished round (tightening torque range: 0.78 to 1.08N•m)
Module mounting screw
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

6 - 29 6 - 29
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
TB2 DB
1 DA
2 DB TB3 DG
3 DG Insulation TB4 SLD
4 SLD TB5 +24V
5 +24V TB6 (FG)
6 FG TB7 24G
7 24G
Module power supply TB8 X0
TB9 X1
8 X0 TB10 X2
9 X1 TB11 X3
10 X2
TB12 X4
11 X3
12 X4 TB13 X5
13 X5 TB14 X6
14 X6 TB15 X7
15 X7 TB16 X8
16 X8 TB17 X9
17 X9
TB18 XA
18 XA
19 XB
TB19 XB
20 XC TB20 XC
21 XD TB21 XD
22 XE TB22 XE
Load
23 XF TB23 XF
24 Y10
TB24 Y10
25 Y11
26 Y12
TB25 Y11
27 Y13 TB26 Y12
28 Y14 TB27 Y13
29 Y15 TB28 Y14
30 Y16 TB29 Y15
31 Y17
TB30 Y16
32 Y18
33 Y19
TB31 Y17
34 Y1A TB32 Y18
35 Y1B TB33 Y19
36 Y1C TB34 Y1A
Load 37 Y1D TB35 Y1B
38 Y1E
TB36 Y1C
39 Y1F
TB37 Y1D
External power supply 40 COM+
41 COM- TB38 Y1E
for output part
TB39 Y1F
Load power supply TB40 COM+
Constant-voltage circuit
TB41 COM-

Load
External power supply for output part
40 COM+ and load power supply (common)
41 COM-

6 - 30 6 - 30
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.1.16 AJ65SBTB1-32KDT2 combined module

Type DC input transistor output combined module

Item AJ65SBTB1-32KDT2 Appearance
Input Output
Number of input points 16 points Number of output points 16 points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 24VDC
Operating load voltage 20.4 to 28.8VDC
Rated input current Approx. 7mA
range (ripple ratio: within 5%)
20.4 to 28.8VDC
Operating voltage range Max. load current 0.5A/point, 3.6A/common
(ripple ratio: within 5%)
Max. number of simultaneous 100% (at 26.4VDC),
Max. inrush current 1.0A, 10ms or less
input points 75% (at 28.8VDC)
ON voltage/ON current 14VDC or higher/4mA or higher Leakage current at OFF 0.1mA or lower
0.3VDC or lower (TYP.) 0.5A,
OFF voltage/OFF current 5.5VDC or lower/1.7mA or lower Max. voltage drop at ON
0.6VDC or lower (MAX.) 0.5A
Output type Sink type
Input resistance Approx. 3.0kΩ
Protection function None

Input response OFF→ON 0.5ms or less

0.2ms 1.5ms 5ms 10ms Response time
speed ON→OFF 1.5ms or less (resistive load)
Response 0.2ms 1.5ms 5ms or 10ms 19.2 to 28.8VDC
OFF→ON Voltage
time or less or less less or less External power (ripple ratio: within 5%)
supply for 15mA or lower
0.2ms 1.5ms 5ms or 10ms
ON→OFF output part Current (at 24VDC and all points ON),
or less or less less or less
excluding external load current
Input type Positive common (sink type) Surge suppressor Zener diode
Wiring method for common 32 points/common (1-wire, terminal block type)
Number of occupied stations 32-point assignment/station (32 points used)
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
supply Current 65mA or lower (at 24VDC and all points ON)
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity
noise frequency 25 to 60Hz (DC type noise simulator condition)
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
10MΩ or higher between all DC external terminals and ground (500VDC insulation resistance
Insulation resistance
tester)
Protection degree IP2X
Weight 0.26kg
Communication 7-point two-piece terminal block
part, [Transmission circuit, module power supply, FG]
module power M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
External
supply part Applicable solderless terminal: 2 or less
connection
34-point direct-mount terminal block
system I/O power supply
[I/O power supply, I/O signal]
part,
M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
I/O part
Applicable solderless terminal: 2 or less
M4 screw with plain washer finished round (tightening torque range: 0.78 to 1.08N•m)
Module mounting screw
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

6 - 31 6 - 31
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
TB2 DB
1 DA
2 DB TB3 DG
3 DG Insulation TB4 SLD
4 SLD TB5 +24V
5 +24V
TB6 (FG)
6 FG
7 24G TB7 24G
Module power supply TB8 X0
TB9 X1
8 X0 TB10 X2
9 X1
TB11 X3
10 X2
11 X3 TB12 X4
12 X4 TB13 X5
13 X5 TB14 X6
14 X6
TB15 X7
15 X7
16 X8 TB16 X8
17 X9 TB17 X9
18 XA TB18 XA
19 XB
TB19 XB
20 XC
21 XD TB20 XC
22 XE TB21 XD
23 XF TB22 XE
Load
24 Y10
TB23 XF
25 Y11
26 Y12 TB24 Y10
27 Y13 TB25 Y11
28 Y14 TB26 Y12
29 Y15
TB27 Y13
30 Y16
31 Y17 TB28 Y14
32 Y18 TB29 Y15
33 Y19 TB30 Y16
34 Y1A
TB31 Y17
35 Y1B
36 Y1C TB32 Y18
Load
37 Y1D TB33 Y19
38 Y1E TB34 Y1A
39 Y1F
TB35 Y1B
40 COM+
External power supply 41 COM- TB36 Y1C
for output part
TB37 Y1D
Load power supply TB38 Y1E
Constant-voltage circuit TB39 Y1F
TB40 COM+
Load TB41 COM-
External power supply for output part
40 COM+ and load power supply (common)
41 COM-

6 - 32 6 - 32
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.1.17 AJ65SBTB1-32DT3 combined module

Type DC input transistor output combined module

Item AJ65SBTB1-32DT3 Appearance
Input Output
Number of input points 16 points Number of output points 16 points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 24VDC
Operating load voltage 19.2 to 26.4VDC
Rated input current Approx. 5mA
range (ripple ratio: within 5%)
19.2 to 26.4VDC
Operating voltage range Max. load current 0.5A/point, 3.6A/common
(ripple ratio: within 5%)
Max. number of simultaneous
100% Max. inrush current 1.0A, 10ms or less
input points
ON voltage/ON current 15VDC or higher/3mA or higher Leakage current at OFF 0.1mA or lower
0.3VDC or lower (TYP.) 0.5A,
OFF voltage/OFF current 3VDC or lower/0.5mA or lower Max. voltage drop at ON
0.6VDC or lower (MAX.) 0.5A
Output type Sink type

Y1F COM-
Input resistance Approx. 4.7kΩ

Y1E COM+
B RATE
40 20 10 8 4 2 1 4 2 1
Protection function None

Y1D
OFF→ON 0.2ms or less (at 24VDC) OFF→ON 0.5ms or less

STATION NO.

Y1C
Response time Response time

Y1B
ON→OFF 0.2ms or less (at 24VDC) ON→OFF 1.5ms or less (resistive load)

Y1A
19.2 to 26.4VDC

Y19
Voltage

Y18
ON
External power (ripple ratio: within 5%)

Y17
Y16
supply for 24.2mA or lower

Y15
Y14
output part Current (at 24VDC and all points ON),

Y13
Y12
excluding external load current

Y10 11 12 13 14 15 16 17 Y18 19 1A1B 1C1D1E 1F

Y11
Input type Positive common (sink type) Surge suppressor Zener diode

Y10
XF
Wiring method for common 32 points/common (1-wire, terminal block type)

XE
XD
Number of occupied stations 32-point assignment/station (32 points used)

XC
XB
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

XA
X9
supply Current 60mA or lower (at 24VDC and all points ON)

X8
X7
Noise voltage 500Vp-p, noise width 1µs,

X6
Noise immunity

X8 9 A B C D E F

X5
noise frequency 25 to 60Hz (DC type noise simulator condition)

X4
AJ65SBTB1-32DT3

X3
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

X2
10MΩ or higher between all DC external terminals and ground (500VDC insulation resistance

X1
Insulation resistance
X0
tester)
PW L RUN L ERR. X0 1 2 3 4 5 6 7

Protection degree IP2X

(FG)
24G

Weight 0.25kg
DG +24V
SLD

7-point two-piece terminal block

Communication part,
DB

[Transmission circuit, module power supply, FG]

DA

module power supply

M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
External part
Applicable solderless terminal: 2 or less
connection
34-point direct-mount terminal block
system
I/O power supply part, [I/O power supply, I/O signal]
I/O part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
M4 screw with plain washer finished round (tightening torque range: 0.78 to 1.08N•m)
Module mounting screw
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

6 - 33 6 - 33
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
TB2 DB
1 DA
2 DB TB3 DG
3 DG TB4 SLD
Insulation
4 SLD TB5 +24V
5 +24V TB6 (FG)
6 FG TB7 24G
7 24G
Module power supply TB8 X0
TB9 X1
8 X0 TB10 X2
9 X1 TB11 X3
10 X2
TB12 X4
11 X3
12 X4 TB13 X5
13 X5 TB14 X6
14 X6 TB15 X7
15 X7 TB16 X8
16 X8 TB17 X9
17 X9
TB18 XA
18 XA
19 XB
TB19 XB
20 XC TB20 XC
21 XD TB21 XD
22 XE TB22 XE
Load
23 XF TB23 XF
24 Y10
TB24 Y10
25 Y11
26 Y12
TB25 Y11
27 Y13 TB26 Y12
28 Y14 TB27 Y13
29 Y15 TB28 Y14
30 Y16 TB29 Y15
31 Y17
TB30 Y16
32 Y18
TB31 Y17
33 Y19
34 Y1A TB32 Y18
35 Y1B TB33 Y19
36 Y1C TB34 Y1A
Load 37 Y1D TB35 Y1B
38 Y1E
TB36 Y1C
39 Y1F
TB37 Y1D
40 COM+
External power supply TB38 Y1E
41 COM-
for output part
TB39 Y1F
Load power supply TB40 COM+
Constant-voltage circuit TB41 COM-

Load
External power supply for output part
40 COM+ and load power supply (common)
41 COM-

6 - 34 6 - 34
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.1.18 AJ65SBTB1-32KDT8 combined module

Type DC input transistor output combined module

Item AJ65SBTB1-32KDT8 Appearance
Input Output
Number of input points 16 points Number of output points 16 points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 12VDC Rated load voltage 12VDC
Operating load voltage 10.2 to 14.4VDC
Rated input current Approx. 11mA
range (ripple ratio: within 5%)
10.2 to 14.4VDC
Operating voltage range Max. load current 0.5A/point, 3.6A/common
(ripple ratio: within 5%)
Max. number of simultaneous
100% Max. inrush current 1.0A, 10ms or less
input points
ON voltage/ON current 5.6VDC or higher/4mA or higher Leakage current at OFF 0.1mA or lower
0.3VDC or lower (TYP.) 0.5A,
OFF voltage/OFF current 2.4VDC or lower/1.7mA or lower Max. voltage drop at ON
0.6VDC or lower (MAX.) 0.5A
Output type Sink type
Input resistance Approx. 1.0kΩ
Protection function None
Input response
0.2ms 1.5ms 5ms 10ms
speed
OFF→ON 0.5ms or less
0.2ms 1.5ms 5ms or 10ms
Response time OFF→ON Response time
or less or less less or less
0.2ms 1.5ms 5ms or 10ms
ON→OFF ON→OFF 1.5ms or less (resistive load)
or less or less less or less
10.2 to 14.4VDC
Voltage
External power (ripple ratio: within 5%)
supply for 15mA or lower
output part Current (at 12VDC and all points ON),
excluding external load current
Input type Positive common (sink type) Surge suppressor Zener diode
Wiring method for common 32 points/common (1-wire, terminal block type)
Number of occupied stations 32-point assignment/station (32 points used)
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
supply Current 65mA or lower (at 24VDC and all points ON)
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity
noise frequency 25 to 60Hz (DC type noise simulator condition)
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
10MΩ or higher between all DC external terminals and ground (500VDC insulation resistance
Insulation resistance
tester)
Protection degree IP2X
Weight 0.26kg
7-point two-piece terminal block
Communication part,
[Transmission circuit, module power supply, FG]
module power supply
M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
External part
Applicable solderless terminal: 2 or less
connection
34-point direct-mount terminal block
system
I/O power supply part, [I/O power supply, I/O signal]
I/O part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
M4 screw with plain washer finished round (tightening torque range: 0.78 to 1.08N•m)
Module mounting screw
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

6 - 35 6 - 35
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
1 DA TB2 DB
2 DB TB3 DG
3 DG Insulation TB4 SLD
4 SLD
TB5 +24V
5 +24V
6 FG TB6 (FG)
7 24G TB7 24G
Module power supply
TB8 X0
TB9 X1
8 X0
TB10 X2
9 X1
10 X2 TB11 X3
11 X3 TB12 X4
12 X4 TB13 X5
13 X5
TB14 X6
14 X6
15 X7 TB15 X7
16 X8 TB16 X8
17 X9 TB17 X9
18 XA
TB18 XA
19 XB
20 XC TB19 XB
21 XD TB20 XC
22 XE TB21 XD
23 XF
Load TB22 XE
24 Y10
25 Y11 TB23 XF
26 Y12 TB24 Y10
27 Y13 TB25 Y11
28 Y14
TB26 Y12
29 Y15
30 Y16 TB27 Y13
31 Y17 TB28 Y14
32 Y18 TB29 Y15
33 Y19
TB30 Y16
34 Y1A
35 Y1B TB31 Y17
36 Y1C TB32 Y18
Load 37 Y1D TB33 Y19
38 Y1E
TB34 Y1A
39 Y1F
40 COM+ TB35 Y1B
External power supply
41 COM- TB36 Y1C
for output part
TB37 Y1D
Load power supply
TB38 Y1E
Constant-voltage circuit TB39 Y1F
TB40 COM+
Load
TB41 COM-
External power supply for output part
40 COM+ and load power supply (common)
41 COM-

6 - 36 6 - 36
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.1.19 AJ65SBTB1-32DTE1 combined module

Type DC input transistor output combined module

Item AJ65SBTB1-32DTE1 Appearance
Input Output
Number of input points 16 points Number of output points 16 points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 24VDC
Operating load voltage 19.2 to 26.4VDC
Rated input current Approx. 7mA
range (ripple ratio: within 5%)
19.2 to 26.4VDC
Operating voltage range Max. load current 0.5A/point, 3.6A/common
(ripple ratio: within 5%)
Max. number of simultaneous
100% Max. inrush current 1.0A, 10ms or less
input points
ON voltage/ON current 14VDC or higher/3.5mA or higher Leakage current at OFF 0.1mA or lower
0.5VDC or lower (TYP.) 0.5A,
OFF voltage/OFF current 6VDC or lower/1.7mA or lower Max. voltage drop at ON
0.8VDC or lower (MAX.) 0.5A
Input resistance Approx. 3.3kΩ Output type Source type

Y1B Y1D Y1F COM-

Y10 Y12 Y14 Y16 Y18 Y1A Y1C Y1E COM+
B RATE
4 2 1
OFF→ON 1.5ms or less (at 24VDC) OFF→ON 0.5ms or less
Response time Response time

40 20 10 8 4 2 1
ON→OFF 1.5ms or less (at 24VDC) ON→OFF 1.5ms or less (resistive load)

STATION NO.
19.2 to 26.4VDC
Voltage
External power (ripple ratio: within 5%)

Y19
ON
supply for 10mA or lower

Y17
output part Current (TYP. 24VDC/common),

Y15
excluding external load current

Y13
Input type Negative common (source type) Surge suppressor Zener diode

Y18 19 1A 1B 1C 1D 1E 1F

Y11
Wiring method for common 32 points/common (1-wire, terminal block type)

XF
Number of occupied stations 32-point assignment/station (32 points used)

XE
XD
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

XC
Y10 11 12 13 14 15 16 17

XB
supply Current 50mA or lower (at 24VDC and all points ON)

XA
X9
Noise voltage 500Vp-p, noise width 1µs,

X8
Noise immunity

X7
noise frequency 25 to 60Hz (DC type noise simulator condition)

X6
X8 9 A B C D E F

X5
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground

X4
AJ65SBTB1-32DTE1

X3
10MΩ or higher between all DC external terminals and ground (500VDC insulation resistance

X2
Insulation resistance
tester)

X1
X0
PW L RUN L ERR. X0 1 2 3 4 5 6 7

Protection degree IP2X

Weight 0.26kg
24G
(FG)

Communication 7-point two-piece terminal block

DA DG +24V
DB SLD

part, [Transmission circuit, module power supply, FG]

module power M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
External
supply part Applicable solderless terminal: 2 or less
connection
34-point direct-mount terminal block
system I/O power supply
[I/O power supply, I/O signal]
part,
M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
I/O part
Applicable solderless terminal: 2 or less
M4 screw with plain washer finished round
Module mounting screw (tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
y RAV1.25-3 (compliant with JIS C 2805)
[Applicable wire size: 0.3 to 1.25mm2]
Applicable solderless terminal
y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Accessory User’s manual

6 - 37 6 - 37
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection
Terminal number Signal name
TB1 DA
TB2 DB
1 DA TB3 DG
2 DB TB4 SLD
3 DG TB5 +24V
Insulation
4 SLD
TB6 (FG)
5 +24V
6 FG TB7 24G
7 24G TB8 X0
Module power supply
TB9 X1
8 X0
TB10 X2
9 X1
10 X2
TB11 X3
11 X3 TB12 X4
12 X4 TB13 X5
13 X5 TB14 X6
14 X6 TB15 X7
15 X7
TB16 X8
16 X8
17 X9 TB17 X9
18 XA TB18 XA
19 XB TB19 XB
20 XC TB20 XC
21 XD
TB21 XD
22 XE
23 XF TB22 XE
Load
24 Y10 TB23 XF
25 Y11 TB24 Y10
26 Y12 TB25 Y11
27 Y13
TB26 Y12
28 Y14
29 Y15
TB27 Y13
30 Y16 TB28 Y14
31 Y17 TB29 Y15
32 Y18 TB30 Y16
33 Y19
TB31 Y17
34 Y1A
35 Y1B
TB32 Y18
36 Y1C TB33 Y19
37 Y1D TB34 Y1A
Load power supply 38 Y1E TB35 Y1B
39 Y1F TB36 Y1C
40 COM+
TB37 Y1D
41 COM-
External power supply Constant-voltage circuit TB38 Y1E
for output part TB39 Y1F
TB40 COM+
Load
TB41 COM-

External power supply for output part

40 COM+ and load power supply (common)
41 COM-

6 - 38 6 - 38
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.1.20 AJ65DBTB1-32DT1 combined module

Type DC input transistor output combined module

Item AJ65DBTB1-32DT1 Appearance
Input Output
Number of input points 16 points Number of output points 16 points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 12/24VDC
Rated input current Approx. 5mA Operating load voltage 10.2 to 31.2VDC
range (ripple ratio: within 5%)
Operating voltage range 20.4 to 31.2VDC Max. load current 0.5A/point, 4A/common
(ripple ratio: within 5%) (2A/terminal)
Max. number of simultaneous 100% (at 26.4VDC) Max. inrush current 1.2A, 10ms or less
input points
ON voltage/ON current 15VDC or higher/3mA or Leakage current at OFF 0.1mA or lower
higher
OFF voltage/OFF current 5VDC or lower/1.5mA or lower Max. voltage drop at ON 0.3VDC or lower (TYP.) 0.5A,
0.6VDC or lower (MAX.) 0.5A
Input resistance Approx. 4.7kΩ Output type Sink type
Protection function None
Response OFF→ON 10ms or less (at 24VDC) Response OFF→ON 0.5ms or less
time ON→OFF 10ms or less (at 24VDC) time ON→OFF 1.5ms or less (resistive load)
External Voltage 10.2 to 31.2VDC
power supply (ripple ratio: within 5%)
for output part Current 30mA or lower
(at 24VDC and all points ON),
excluding external load current
Input type Positive common (sink type) Surge suppressor Zener diode
Wiring method for common 16 points/common (2 points) (1-wire, terminal block type)
Number of occupied stations 32-point assignment/station (32 points used)
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
supply Current 55mA or lower (at 24VDC and all points ON)
Noise immunity Noise voltage 500Vp-p, noise width 1µs,
noise frequency 25 to 60Hz (DC type noise simulator condition)
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
Insulation resistance 10MΩ or higher between all DC external terminals and ground (500VDC insulation resistance
tester)
Protection degree IP2X
Weight 0.65kg
External connection system 50-point terminal block
[Transmission circuit, module power supply, FG, I/O power supply, I/O signal]
M3.5×7 screw (tightening torque range: 0.68 to 0.92N•m)
Applicable solderless terminal: 2 or less
Module mounting screw M4 screw with plain washer finished round (tightening torque range: 0.78 to 1.08N•m)
Applicable solderless terminal R1.25-3.5, RAV2-3.5 (compliant with JIS C 2805)
Accessory User’s manual
Part sold separately A6DIN1C, A2CCOM-TB

6 - 39 6 - 39
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection
Terminal Signal Terminal Signal
number name number name
TB1 DA TB26 Empty
TB2 DG TB27 Empty
TB3 DB Insulation TB28 +24V
1 DA Empty 26
TB4 Empty 2 DG Empty 27
TB29 CTL+
TB5 SLD 3 DB +24V 28
24VDC TB30 (FG)
4 Empty CTL+ 29
TB6 Empty 5 SLD FG 30 TB31 CTLG
6 Empty CTLG 31
TB7 24G TB32 24G
7 24G 24G 32
TB8 X0 Module TB33 Y10
Constant-voltage
power supply
circuit
TB9 X1 TB34 Y11
TB10 X2 TB35 Y12
Load
Y10 33
TB11 X3 8 X0 TB36 Y13
9 X1 Y11 34
TB12 X4 10 X2 Y12 35 TB37 Y14
11 X3 Y13 36
TB13 X5 Y14 37
TB38 Y15
12 X4
TB14 X6 13 X5 Y15 38 TB39 Y16
14 X6 Y16 39
TB15 X7 15 X7 Y17 40
Load TB40 Y17
TB16 COM1 16 COM1 COM3 41
Load TB41 COM3
17 X8 Y18 42
TB17 X8 18 X9 Y19 43 TB42 Y18
19 XA Y1A 44
TB18 X9 TB43 Y19
20 XB Y1B 45
TB19 XA 21 XC Y1C 46 TB44 Y1A
22 XD Y1D 47
TB20 XB 23 XE Y1E 48
TB45 Y1B
Load
TB21 XC 24 XF Y1F 49 TB46 Y1C
25 COM2 COM4 50
TB22 XD 24VDC TB47 Y1D
TB23 XE TB48 Y1E
TB24 XF TB49 Y1F
TB25 COM2 TB50 COM4

6 - 40 6 - 40
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.1.21 AJ65DBTB1-32DR combined module

Type DC input contact output combined module

Item AJ65DBTB1-32DR Appearance
Input Output
Number of input points 16 points Number of output points 16 points
Isolation method Photocoupler Isolation method Photocoupler
2A/point, 4A/common (2A/terminal)
Rated input voltage 24VDC Rated load voltage at 24VDC (resistive load) or
240VAC (cosφ=1)
Rated input current Approx. 5mA Min. switching load 5VDC, 1mA
Operating voltage 20.4 to 31.2VDC
Max. switching voltage 264VAC, 125VDC
range (ripple ratio: within 5%)
Max. number of
simultaneous input 100% (at 26.4VDC) Mechanical 20 million times or more
points
Rated switching voltage/current
load:
100 thousand times or more
200VAC 1.5A, 240VAC 1A
Life (cosφ=0.7):
15VDC or higher/3mA or 100 thousand times or more
ON voltage/ON current Electrical
higher 200VAC 1A, 240VAC 0.5A
(cosφ=0.35):
100 thousand times or more
24VDC 1A, 100VDC 0.1A
(L/R=7ms):
100 thousand times or more
OFF voltage/OFF 5VDC or lower/1.5mA or
Max. switching frequency 3600 times/hour
current lower
Input resistance Approx. 4.7kΩ Response time OFF→ON 10ms or less
OFF→ON 10ms or less (at 24VDC) ON→OFF 12ms or less
Response
External power 24VDC ±10%
time ON→OFF 10ms or less (at 24VDC) Voltage
supply for output part (ripple ratio: 4Vp-p or lower)
(CTL+ and CTLG 90mA or lower
Current
terminals) (at 24VDC and all points ON)
Wiring method for 16 points/common (2 points) 8 points/common
Wiring method for common
common (1-wire, terminal block type) (1-wire, terminal block type)
Positive/negative common
Input type shared type Surge suppressor None
(sink/source shared type)
Number of occupied
32-point assignment/station (32 points used)
stations
Module Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
power supply Current 60mA or lower (at 24VDC and all points ON)
Noise voltage: 1500Vp-p (AC type), 500Vp-p (DC type), noise width 1µs,
Noise immunity
noise frequency 25 to 60Hz (noise simulator condition)
1500VAC for 1 minute between all AC external terminals and ground
Withstand voltage
500VAC for 1 minute between all DC external terminals and ground
10MΩ or higher between all AC external terminals and ground (500VDC insulation resistance tester)
Insulation resistance
10MΩ or higher between all DC external terminals and ground (500VDC insulation resistance tester)
Protection degree IP1X
Weight 0.65kg
50-point terminal block [Transmission circuit, module power supply, FG, I/O power supply, I/O signal]
External connection
M3.5×7 screw (tightening torque range: 0.68 to 0.92N•m)
system
Applicable solderless terminal: 2 or less
Module mounting screw M4 screw with plain washer finished round (tightening torque range: 0.78 to 1.08N•m)
Applicable solderless
R1.25-3.5, RAV2-3.5 (compliant with JIS C 2805)
terminal
Accessory User’s manual
Part sold separately A6DIN1C, A2CCOM-TB

6 - 41 6 - 41
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection
Terminal Signal Terminal Signal
number name number name
TB1 DA TB26 Empty
TB2 DG TB27 Empty
TB3 DB TB28 +24V
Insulation
TB4 Empty 1 DA Empty 26 TB29 CTL+
2 DG Empty 27
24VDC (FG)
TB5 SLD 3 DB CTL+ +24V 28 TB30
4 Empty CTL+ 29
TB6 Empty TB31 CTLG
5 SLD FG 30
TB7 24G 6 Empty CTLG CTLG 31 TB32 24G
7 24G 24G 32
TB8 X0 Module power supply TB33 Y10
TB9 X1 Load TB34 Y11
8 X0 CTL+ Y10 33
TB10 X2 9 X1 Y11 34 TB35 Y12
10 X2 Y12 35
TB11 X3 TB36 Y13
11 X3 Y13 36
TB12 X4 12 X4 Y14 37 TB37 Y14
13 X5 Y15 38
TB13 X5 14 X6 Y16 39 TB38 Y15
Load
TB14 X6 15 X7
CTLG Y17 40 TB39 Y16
16 COM1 COM3 41
Load
TB15 X7 17 X8 CTL+ Y18 42 TB40 Y17
18 X9 Y19 43
TB16 COM1 19 XA Y1A 44
TB41 COM3
TB17 X8 20 XB Y1B 45 TB42 Y18
21 XC Y1C 46
TB18 X9 22 XD Y1D 47 TB43 Y19
23 XE Y1E 48
TB19 XA 24 XF Y1F 49
Load TB44 Y1A
CTLG
TB20 XB 25 COM2 COM4 50 TB45 Y1B
TB21 XC TB46 Y1C
24VDC
TB22 XD TB47 Y1D
TB23 XE TB48 Y1E
TB24 XF TB49 Y1F
TB25 COM2 TB50 COM4

6 - 42 6 - 42
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.2 Spring Clamp Terminal Block Type Combined Module

6.2.1 AJ65VBTS32-16DT combined module

Type DC input transistor output combined module

Item AJ65VBTS32-16DT Appearance
Input Output
Number of input points 8 points Number of output points 8 points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 24VDC
Operating load voltage 19.2 to 26.4VDC
Rated input current Approx. 5mA
range (ripple ratio: within 5%)
19.2 to 26.4VDC
Operating voltage range Max. load current 0.5A/point, 4A/common
(ripple ratio: within 5%)
Max. number of simultaneous
100% Max. inrush current 1.0A, 10ms or less
input points
14VDC or higher/3.5mA or
ON voltage/ON current Leakage current at OFF 0.1mA or lower
higher
OFF voltage/OFF current 6VDC or lower/1.7mA or lower 0.3VDC or lower (TYP.) 0.5A,
Max. voltage drop at ON
Input resistance Approx. 4.7kΩ 0.6VDC or lower (MAX.) 0.5A
OFF→ON 1.5ms or less (at 24VDC) Output type Sink type
Response time
ON→OFF 1.5ms or less (at 24VDC) Protection function None
Response OFF→ON 1ms or less
time ON→OFF 1ms or less (resistive load)
19.2 to 26.4VDC
External Voltage
(ripple ratio: within 5%)
power

YF
15mA or lower
supply for

YD YE
Current (at 24VDC and all points ON),
output part
excluding external load current

YC

NC
Input type Positive common (sink type) Surge suppressor Zener diode

YB
YA
Supply current for connected
1.0A or lower/common

Y9
device

COM+
Y8
AJ65VBTS32-16DT
16 points/common
Wiring method for common

X7
(input: 3-wire spring clamp terminal block type, output: 2-wire spring clamp terminal block type)

X6
Number of occupied stations 32-point assignment/station (16 points used)

X5
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

X4

COM-
X3
supply Current 40mA or lower (at 24VDC and all points ON)
Noise voltage 500Vp-p, noise width 1µs, X2
Noise immunity
X1

noise frequency 25 to 60Hz (DC type noise simulator condition)

X0

Withstand voltage 500VAC for 1 minute between all DC external terminals and ground COM+

COM-
NC

10MΩ or higher between all DC external terminals and ground (500VDC insulation resistance
Insulation resistance
tester)
D
8 9 A B C D E F
0 1 2 3 4 5 6 7

Protection degree IP1XB

L RUN L ERR.

Weight 0.24kg
C

One-touch connector for communication [Transmission circuit]

Communication
ONPW

5-pin IDC plug is sold separately: A6CON-L5P

B RATE STATION NO.

part
1 2 4 1 2 4 8 1020 40

External <Optional> Online connector for communication: A6CON-LJ5P

CON A

connection One-touch connector for power supply and FG [Module power supply, FG]
system Power supply part 5-pin IDC plug is sold separately: A6CON-PW5P, A6CON-PW5P-SOD
<Optional> Online connector for power supply: A6CON-PWJ5P
I/O part 2-piece spring clamp terminal block [I/O power supply, I/O signals]
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Connector for Applicable cable:
communication FANC-110SBH, FA-CBL200PSBH, CS-110
2
0.66 to 0.98mm (AWG18)
Connector for
[φ2.2 to 3.0mm (A6CON-PW5P), φ2.0 to 2.3mm (A6CON-PW5P-SOD)]
power supply and
Wire diameter: 0.16mm or more
FG
Insulating coating material: PVC (heat-resistant)
Spring clamp 2
Applicable Stranded wire 0.08 to 1.5mm (AWG28 to 16) 1
terminal block for
wire size Wire strip length: 8 to 11mm
I/O
2
TE0.5 [Applicable wire size: 0.5mm ]
TE0.75 [Applicable wire size: 0.75mm2]
Applicable
TE1 [Applicable wire size: 0.9 to 1.0mm2]
solderless
TE1.5 [Applicable wire size: 1.25 to 1.5mm2]
terminal
FA-VTC125T9 [Applicable wire size: 0.3 to 1.65mm2]
FA-VTCW125T9 [Applicable wire size: 0.3 to 1.65mm2]
Accessory User’s manual, Holding fixtures for screw installation

1: Insert one wire per terminal.

6 - 43 6 - 43
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection

Pin number Signal name

1 DA
2 DB
CONA CON A, B
1
1
3 DG
DA
LINK CABLE 2
(IN) 3
2 DB 4 Empty
3 DG
4
4 Empty 5 SLD
5
5 SLD
1 (FG)
CONB
1 2 +24V (UNIT)
1 DA
LINK CABLE 2
2 DB
(OUT) 3
3 DG
CON C, D 3 24G (UNIT)
4
5
4 Empty 4 Empty
5 SLD
One-touch connector for communication 5 Empty
CONC Insulation Terminal block
1
UNIT POWER CABLE(IN) 1 FG
2
3
2 +24V(UNIT) Column A Column B Column C
3 24G(UNIT)
4
4 Empty 1 Empty 1 COM+ 1 COM-
5
5 Empty
2 X0 2 COM+ 2 COM-
COND
UNIT POWER CABLE(OUT) 1
1 FG 3 X1 3 COM+ 3 COM-
2
2 +24V(UNIT)
3
3 24G(UNIT)
4 X2 4 COM+ 4 COM-
4
5
4 Empty 5 X3 5 COM+ 5 COM-
5 Empty Constant-voltage circuit
1
One-touch connector for power supply and FG 6 X4 6 COM+ 6 COM-
TB1A Empty 7 X5 7 COM+ 7 COM-
TB1B COM+
TB1C COM-
8 X6 8 COM+ 8 COM-
TB2A X0 9 X7 9 COM+ 9 COM-
TB2B COM+
TB2C COM- 10 Y8 10 COM+ 10 Empty
TB3A X1
TB3B COM+
11 Y9 11 COM+ 11 Empty
TB3C COM- 12 YA 12 COM+ 12 Empty
TB4A X2
TB4B COM+ 13 YB 13 COM+ 13 Empty
TB4C COM-
TB5A X3 14 YC 14 COM+ 14 Empty
TB5B COM+
15 YD 15 COM+ 15 Empty
TB5C COM-
TB6A X4 16 YE 16 COM+ 16 Empty
TB6B COM+
TB6C COM- 17 YF 17 COM+ 17 Empty
TB7A X5
TB7B COM+
TB7C COM-
TB8A X6
TB8B COM+
TB8C COM-
TB9A X7
TB9B COM+
TB9C COM-
Load
TB10A Y8
TB10B COM+
TB10C Empty
TB11A Y9
TB11B COM+
TB11C Empty
TB12A YA
TB12B COM+
TB12C Empty
TB13A YB
TB13B COM+
TB13C Empty
TB14A YC
TB14B COM+
TB14C Empty
TB15A YD
TB15B COM+
TB15C Empty
TB16A YE
TB16B COM+
Load TB16C Empty
TB17A YF
TB17B COM+
TB17C Empty

1:Attach an unwired connector plug to an unused one-touch connector for power supply and FG.

6 - 44 6 - 44
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection

<When using online connectors>

Online connector
for communication
CONA
1
1 DA
LINK CABLE 2
(IN) 2 DB
3
3 DG
4
4 Empty
5
5 SLD
CONB
1
1 DA
LINK CABLE 2
(OUT) 2 DB
3
3 DG
4
4 Empty
5
5 SLD
One-touch connector
for communication
CONC
UNIT POWER CABLE(IN) 1
1 FG
2
2 +24V(UNIT)
3
3 24G(UNIT)
4
4 Empty
5
5 Empty
COND
1
1 FG
2
UNIT POWER 2 +24V(UNIT)
CABLE(OUT) 3
3 24G(UNIT)
4
4 Empty
5 Empty
5

One-touch connector for power

Online connector
supply and FG *1
for power supply
and FG

1:Attach an unwired connector plug to an unused one-touch connector for power supply and FG.

Pin layout

Viewed from the front of the module

6 - 45 6 - 45
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.2.2 AJ65VBTS32-32DT combined module

Type DC input transistor output combined module
Item AJ65VBTS32-32DT Appearance
Input Output
Number of input points 16 points Number of output points 16 points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 12/24VDC
Operating load voltage 10.2 to 26.4VDC
Rated input current Approx. 5mA
range (ripple ratio: within 5%)
19.2 to 26.4VDC
Operating voltage range Max. load current 0.5A/point, 4A/common
(ripple ratio: within 5%)
Max. number of simultaneous 100% or 75%
Max. inrush current 1.0A, 10ms or less
input points (Refer to Section1.3.)
14VDC or higher/3.5mA or
ON voltage/ON current Leakage current at OFF 0.1mA or lower
higher
OFF voltage/OFF current 6VDC or lower/1.7mA or lower 0.3VDC or lower (TYP.) 0.5A,
Max. voltage drop at ON
Input resistance Approx. 4.7kΩ 0.6VDC or lower (MAX.) 0.5A
OFF→ON 1.5ms or less (at 24VDC) Output type Sink type
Response time

X9 XA XB XC XD XE XF NC Y10 Y11 Y12 Y13 Y14 Y15 Y16 Y17 Y18 Y19 Y1A Y1B Y1C Y1D Y1E Y1F
ON→OFF 1.5ms or less (at 24VDC) Protection function None
OFF→ON 1ms or less
Response time
ON→OFF 1ms or less (resistive load)
10.2 to 26.4VDC
Voltage
External power (ripple ratio: within 5%)
supply for

COM2+
30mA or lower

NC
output part Current (at 24VDC and all points ON),
excluding external load current
16 points/common 16 points/common
Wiring method for common (3-wire, spring clamp terminal Wiring method for common (2-wire, spring clamp terminal block
block type) type)

AJ65VBTS32-32DT
Input type Positive common (sink type) Surge suppressor Zener diode

COM2+

COM2-
Supply current for connected
1.0A or lower/common
device
Number of occupied stations 32-point assignment/station (32 points used)
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
supply Current 50mA or lower (at 24VDC and all points ON)
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity

COM1+

COM1-
X8
noise frequency 25 to 60Hz (DC type noise simulator condition)
X7
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
X6
10MΩ or higher between all DC external terminals and ground (500VDC insulation resistance
X5

Insulation resistance
X4

tester)
X3

Protection degree IP1XB

X2

Weight 0.41kg
X1
X0

One-touch connector for communication [Transmission circuit]

COM1+

COM1-

Communication
NC

5-pin IDC plug is sold separately: A6CON-L5P

part
External <Optional> Online connector for communication: A6CON-LJ5P
D
8 9 A B CD E F
0 1 2 3 4 5 6 7

connection One-touch connector for power supply and FG [Module power supply, FG]
L ERR.

Power supply
system
C

5-pin IDC plug is sold separately: A6CON-PW5P, A6CON-PW5P-SOD

PW L RUN

part
<Optional> Online connector for power supply: A6CON-PWJ5P
B
ON

B RATESTATION NO.

I/O part 2-piece spring clamp terminal block [I/O power supply, I/O signals]
1 2 4 1 2 4 8 102040
CON A

Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)

Connector for Applicable cable:
communication FANC-110SBH, FA-CBL200PSBH, CS-110
2
0.66 to 0.98mm (AWG18)
Connector for
[φ2.2 to 3.0mm (A6CON-PW5P), φ2.0 to 2.3mm (A6CON-PW5P-SOD)]
power supply
Wire diameter: 0.16mm or more
and FG
Insulating coating material: PVC (heat-resistant)
Spring clamp
Applicable Stranded wire 0.08 to 1.5mm2 (AWG28 to 16) 1
terminal block
wire size Wire strip length: 8 to 11mm
for I/O
2
TE0.5 [Applicable wire size: 0.5mm ]
2
TE0.75 [Applicable wire size: 0.75mm ]
Applicable 2
TE1 [Applicable wire size: 0.9 to 1.0mm ]
solderless 2
TE1.5 [Applicable wire size: 1.25 to 1.5mm ]
terminal
FA-VTC125T9 [Applicable wire size: 0.3 to 1.65mm2]
FA-VTCW125T9 [Applicable wire size: 0.3 to 1.65mm2]
Accessory User’s manual, Holding fixtures for screw installation
1: Insert one wire per terminal.

6 - 46 6 - 46
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection

CONA

LINK CABLE
1
2
1 DA Pin number Signal name
(IN) 2 DB
3
4
3
4
DG
Empty
1 DA
5
5 SLD
2 DB
CONB

LINK CABLE
1
2
1 DA CON A, B 3 DG
2 DB
(OUT) 3
4
3
4
DG
Empty
4 Empty
5
One-touch connector
5 SLD
5 SLD
for communication
1
CONC
1 FG
Insulation 1 (FG)
UNIT POWER CABLE(IN)
2
3
2
3
+24V(UNIT)
+24G(UNIT)
2 +24V (UNIT)
4
5
4
5
Empty
Empty
CON C, D 3 24G (UNIT)
UNIT POWER CABLE(OUT)
1
COND
1 FG
4 Empty
2 24V(UNIT)
3
2
3 24G(UNIT) 5 Empty
4 Empty
5
4
5 Empty Terminal block
One-touch connector for
power supply and FG
1
Column A Column B Column C
TB1A Empty
TB1B COM1+ 1 Empty 1 COM1+ 1 COM1-
TB1C COM1-
TB2A
TB2B
X0
COM1+
2 X0 2 COM1+ 2 COM1-
TB2C
TB3A
COM1-
X1
3 X1 3 COM1+ 3 COM1-
TB3B
TB3C
COM1+
COM1- 4 X2 4 COM1+ 4 COM1-
TB4A X2
TB4B COM1+ 5 X3 5 COM1+ 5 COM1-
TB4C COM1-
TB5A X3 6 X4 6 COM1+ 6 COM1-
TB5B COM1+
TB5C COM1- 7 X5 7 COM1+ 7 COM1-
TB6A X4
TB6B COM1+ 8 X6 8 COM1+ 8 COM1-
TB6C COM1-
TB7A
TB7B
X5
COM1+
9 X7 9 COM1+ 9 COM1-
TB7C
TB8A
COM1-
X6
10 X8 10 COM1+ 10 COM1-
TB8B
TB8C
COM1+
COM1-
11 X9 11 COM1+ 11 COM1-
TB9A X7
TB9B COM1+ 12 XA 12 COM1+ 12 COM1-
TB9C COM1-
TB10A X8 13 XB 13 COM1+ 13 COM1-
TB10B COM1+
TB10C COM1- 14 XC 14 COM1+ 14 COM1-
TB11A X9
TB11B COM1+ 15 XD 15 COM1+ 15 COM1-
TB11C COM1-
TB12A XA 16 XE 16 COM1+ 16 COM1-
TB12B COM1+
TB12C
TB13A
COM1-
XB
17 XF 17 COM1+ 17 COM1-
TB13B
TB13C
COM1+
COM1-
18 Empty 18 COM2+ 18 COM2-
TB14A XC
TB14B COM1+ 19 Y10 19 COM2+ 19 Empty
TB14C COM1-
TB15A XD 20 Y11 20 COM2+ 20 Empty
TB15B COM1+
TB15C COM1- 21 Y12 21 COM2+ 21 Empty
TB16A XE
TB16B COM1+ 22 Y13 22 COM2+ 22 Empty
TB16C COM1-
TB17A
TB17B
XF
COM1+
23 Y14 23 COM2+ 23 Empty
External power supply for output
TB17C
TB18A
COM1-
Empty
24 Y15 24 COM2+ 24 Empty
Constant-
TB18B
TB18C
COM2+
COM1-
voltage circuit
25 Y16 25 COM2+ 25 Empty
Load
TB19A Y10
TB19B COM2+ 26 Y17 26 COM2+ 26 Empty
TB19C Empty
TB20A Y11 27 Y18 27 COM2+ 27 Empty
TB20B COM2+
TB20C Empty 28 Y19 28 COM2+ 28 Empty
TB21A Y12
TB21B COM2+ 29 Y1A 29 COM2+ 29 Empty
TB21C Empty
TB22A Y13
TB22B COM2+
30 Y1B 30 COM2+ 30 Empty
TB22C
TB23A
Empty
Y14
31 Y1C 31 COM2+ 31 Empty
TB23B
TB23C
COM2+
Empty 32 Y1D 32 COM2+ 32 Empty
TB24A Y15
TB24B COM2+ 33 Y1E 33 COM2+ 33 Empty
TB24C Empty
TB25A Y16 34 Y1F 34 COM2+ 34 Empty
TB25B COM2+
TB25C Empty
TB26A Y17
TB26B COM2+
TB26C Empty
TB27A Y18
TB27B COM2+
TB27C Empty
TB28A Y19
TB28B COM2+
TB28C Empty
TB29A Y1A
TB29B COM2+
TB29C Empty
TB30A Y1B
TB30B COM2+
TB30C Empty
TB31A Y1C
TB31B COM2+
TB31C Empty
TB32A Y1D
TB32B COM2+
TB32C Empty
TB33A Y1E
TB33B COM2+
TB33C Empty
Load
TB34A Y1F 1: Attach an unwired connector plug to an unused one-touch
TB34B COM2+
TB34C Empty connector for power supply and FG.

6 - 47 6 - 47
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection

<When using online connectors>

Online connector
for communication
CONA
1
1 DA
LINK CABLE 2
(IN) 2 DB
3
3 DG
4
4 Empty
5
5 SLD
CONB
1
1 DA
LINK CABLE 2
(OUT) 2 DB
3
3 DG
4
4 Empty
5
5 SLD
One-touch connector
for communication
CONC
UNIT POWER CABLE(IN) 1
1 FG
2
2 +24V(UNIT)
3
3 24G(UNIT)
4
4 Empty
5
5 Empty
COND
1
1 FG
2
UNIT POWER 2 +24V(UNIT)
CABLE(OUT) 3
3 24G(UNIT)
4
4 Empty
5 Empty
5

One-touch connector for power

Online connector
supply and FG *1
for power supply
and FG

1: Attach an unwired connector plug to an unused one-touch connector for power supply and FG.

Pin layout

Viewed from the front of the module

6 - 48 6 - 48
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.3 Sensor Connector (e-CON) Type Combined Module

6.3.1 AJ65VBTCE32-16DT combined module

Type DC input transistor output combined module
Item AJ65VBTCE32-16DT Appearance
Input Output
Number of input points 8 points Number of output points 8 points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 24VDC
19.2 to 26.4VDC
Rated input current Approx. 5mA Operating load voltage range
(ripple ratio: within 5%)
19.2 to 26.4VDC
Operating voltage range Max. load current 0.1A/point, 0.8A/common
(ripple ratio: within 5%)
Max. number of simultaneous
100% Max. inrush current 0.7A, 10ms or less
input points
14VDC or higher/3.5mA or
ON voltage/ON current Leakage current at OFF 0.1mA or lower
higher
6VDC or lower/1.7mA or
OFF voltage/OFF current 0.1VDC or lower (TYP.) 0.1A,
lower Max. voltage drop at ON
0.2VDC or lower (MAX.) 0.1A
Input resistance Approx. 4.7kΩ
OFF→ON 1.5ms or less (at 24VDC) Output type Sink type
Response time Overload protection, overvoltage
ON→OFF 1.5ms or less (at 24VDC) Protection function
protection, overheat protection
OFF→ON 1ms or less
Response time
ON→OFF 1ms or less (resistive load)
19.2 to 26.4VDC
Voltage
External power (ripple ratio: within 5%)

F
7
supply for output

AJ65VBTCE32-16DT
5mA or lower

E
6
part Current (at 24VDC and all points ON),

D
5
excluding external load current

C
4
Input type Positive common (sink type) Surge suppressor Zener diode

B
3
Supply current for connected
1.0A or lower/common

A
2
device

9
16 points/common
Wiring method for common

8
(input: 3-wire sensor connector (e-CON) type, output: 2-wire sensor connector (e-CON) type)

Y
Number of occupied stations 32-point assignment/station (16 points used)

D
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
8 9 A B C D E F
0 1 2 3 4 5 6 7
PW L RUNL ERR.

supply Current 40mA or lower (at 24VDC and all points ON)

C
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity
B
noise frequency 25 to 60Hz (DC type noise simulator condition)
ON

B RATE STATION NO.

1 2 4 1 2 4 8102040

Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
CON A

10MΩ or higher between all DC external terminals and ground (500VDC insulation resistance
Insulation resistance
tester)
Protection degree IP1XB
Weight 0.11kg
One-touch connector for communication [Transmission circuit]
Communication
5-pin IDC plug is sold separately: A6CON-L5P
part
External <Optional> Online connector for communication: A6CON-LJ5P
connection One-touch connector for power supply and FG [Module power supply, I/O power supply, FG]
system Power supply part 5-pin IDC plug is sold separately: A6CON-PW5P, A6CON-PW5P-SOD
<Optional> Online connector for power supply: A6CON-PWJ5P
I/O part Sensor connector (e-CON) [I/O signals] 4-pin IDC plug is sold separately. 1
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Connector for Applicable cable:
communication FANC-110SBH, FA-CBL200PSBH, CS-110
2
0.66 to 0.98mm (AWG18)
Connector for
[φ2.2 to 3.0mm (A6CON-PW5P), φ2.0 to 2.3mm (A6CON-PW5P-SOD)]
Applicable power supply and
Wire diameter: 0.16mm or more
wire size FG
Insulating coating material: PVC (heat-resistant)
Sensor connector (e-CON).
Connector for I/O Applicable connector plugs are sold separately. 1
2
(applicable wire size: 0.08 to 0.5mm , depending on the connector plug)
Accessory User’s manual, Holding fixtures for screw installation

1: Refer to Section 1.6.2 for details.

6 - 49 6 - 49
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection

Pin number Signal name

CONA
1
1 DA 1 DA
LINK CABLE 2
2 DB
(IN) 3 2 DB
3 DG
4 CON A,B
4 Empty 3 DG
5
5 SLD
4 Empty
CONB
1
1 DA 5 SLD
LINK CABLE 2
2 DB 1 (FG)
(OUT) 3
3 DG
4
4 Empty 2 +24V (UNIT)
5
5 SLD
CON C,D 3 24G (UNIT)
One-touch connector for communication
4 +24V(I/O)
CONC Insulation 5 24G(I/O)
1
UNIT POWER CABLE(IN) 1 FG
2 Pin Signal Pin Signal
2 +24V(UNIT)
3
3 24G(UNIT)
4 +24V(I/O)
number name number name
4
5
5 24G(I/O) 1 +24V 1 +24V
I/O POWER CABLE(IN) COND
CON CON
1 2 +V 2 Empty 1
UNIT POWER CABLE(OUT) 1 FG 1 9
2
2 +24V(UNIT) 3 24G 3 Empty 2
3
24G(UNIT)
(X0) (Y8)
3
4 +24V(I/O)
4 X0 4 Y8
4
5
5 24G(I/O) 1 +24V 1 +24V
I/O POWER CABLE(OUT) CON CON
3 Constant-voltage circuit 2 +V 2 Empty 1
One-touch connector for power supply and FG 2 10
4 CON1 3 24G 3 Empty 2
Brown 1
(X1) (Y9)
3-wire sensor 4 X1 4 Y9
2
(sink output)
Detection
Blue 3 1 +24V 1 +24V
circuit Black 4 CON CON
2 +V 2 Empty 1
3 11
3 24G 3 Empty 2
(X2) (YA)
CON8 4 X2 4 YA
1
1 +24V CON 1 +24V
2 CON
3 2 +V 12 2 Empty 1
4 4
3 24G (YB) 3 Empty 2
(X3)
4 X3 4 YB
CON9
1 1 +24V 1 +24V
2
CON CON
2 +V 2 Empty 1
3 5 13
Load 4 3 24G 3 Empty 2
(X4) (YC)
4 X4 4 YC
2 1 1 +24V 1 +24V
CON CON
CON16 2 +V 2 Empty 1
1 6 14
3 24G 3 Empty 2
2 (X5) (YD)
3 4 X5 4 YD
Load 4
1 +24V 1 +24V
CON CON
2 +V 2 Empty 1
7 15
3 24G 3 Empty 2
(X6) (YE)
4 X6 4 YE
1 +24V 1 +24V
1: Since all No.2 pins of CON9 to CON16 are connected inside the module, they cannot be used. CON CON
2 +V 2 Empty 1
2: Since all No.3 pins of CON9 to CON16 are connected inside the module, they cannot be used. 8 16
3 24G 3 Empty 2
3: Attach an unwired connector plug to an unused one-touch connector for power supply and FG. (X7) (YF)
4: Wiring the sensor connector (e-CON) incorrectly may cause malfunction or failure due to short circuit of the 4 X7 4 YF
power supply.

6 - 50 6 - 50
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection

<When using online connectors>

Online connector
for communication
CONA
1
1 DA
LINK CABLE 2
(IN) 2 DB
3
3 DG
4
4
5
5 SLD
CONB
1
1 DA
LINK CABLE 2
(OUT) 2 DB
3
3 DG
4
4
5
5 SLD
One-touch connector
for communication
CONC
1
UNIT POWER CABLE(IN) 1 FG
2
2 +24V(UNIT)
3
3 24G(UNIT)
4
4 +24V(I/O)
5
5 24G(I/O)
I/O POWER CABLE(IN) COND
1
1 FG
2
UNIT POWER 2 +24V(UNIT)
CABLE(OUT) 3
3 24G(UNIT)
4
I/O POWER 4 +24V(I/O)
CABLE(OUT) 5
5 24G(I/O)

One-touch connector for power

supply and FG *1 Online connector
for power supply
and FG

1: Attach an unwired connector plug to an unused one-touch connector for power supply and FG.
Pin layout

Viewed from the front of the module

6 - 51 6 - 51
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.3.2 AJ65VBTCE3-16DTE combined module

Type DC input transistor output combined module

Item AJ65VBTCE3-16DTE Appearance
Input Output
Number of input points 8 points Number of output points 8 points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 24VDC
19.2 to 26.4VDC
Rated input current Approx. 5mA Operating load voltage range
(ripple ratio: within 5%)
19.2 to 26.4VDC
Operating voltage range Max. load current 0.1A/point, 0.8A/common
(ripple ratio: within 5%)
Max. number of simultaneous
100% Max. inrush current 0.7A, 10ms or less
input points
14VDC or higher/3.5mA or
ON voltage/ON current Leakage current at OFF 0.1mA or lower
higher
6VDC or lower/1.7mA or
OFF voltage/OFF current 0.1VDC or lower (TYP.) 0.1A,
lower Max. voltage drop at ON
0.2VDC or lower (MAX.) 0.1A
Input resistance Approx. 4.7kΩ
OFF→ON 1.5ms or less (at 24VDC) Output type Source type
Response time Overload protection, overheat
ON→OFF 1.5ms or less (at 24VDC) Protection function
protection
OFF→ON 1ms or less
Response time
ON→OFF 1ms or less (resistive load)
19.2 to 26.4VDC
Voltage
External power (ripple ratio: within 5%)
supply for output 7mA or lower
part Current (at 24VDC and all points ON),
excluding external load current
Negative common
Input type Surge suppressor Zener diode
(source type)
Supply current for connected
1.0A or lower/common
device
16 points/common
Wiring method for common
(input: 3-wire sensor connector (e-CON) type, output: 3-wire sensor connector (e-CON) type)
Number of occupied stations 32-point assignment/station (16 points used)
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
supply Current 40mA or lower (at 24VDC and all points ON)
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity
noise frequency 25 to 60Hz (DC type noise simulator condition)
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
10MΩ or higher between all DC external terminals and ground (500VDC insulation resistance
Insulation resistance
tester)
Protection degree IP1XB
Weight 0.11kg
One-touch connector for communication [Transmission circuit]
Communication
5-pin IDC plug is sold separately: A6CON-L5P
part
External <Optional> Online connector for communication: A6CON-LJ5P
connection One-touch connector for power supply and FG [Module power supply, I/O power supply, FG]
system Power supply part 5-pin IDC plug is sold separately: A6CON-PW5P, A6CON-PW5P-SOD
<Optional> Online connector for power supply: A6CON-PWJ5P
I/O part Sensor connector (e-CON) [I/O signals] 4-pin IDC plug is sold separately. 1
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Connector for Applicable cable:
communication FANC-110SBH, FA-CBL200PSBH, CS-110
2
0.66 to 0.98mm (AWG18)
Connector for
[φ2.2 to 3.0mm (A6CON-PW5P), φ2.0 to 2.3mm (A6CON-PW5P-SOD)]
Applicable power supply and
Wire diameter: 0.16mm or more
wire size FG
Insulating coating material: PVC (heat-resistant)
Sensor connector (e-CON).
Connector for I/O Applicable connector plugs are sold separately. 1
2
(applicable wire size: 0.08 to 0.5mm , depending on the connector plug)
Accessory User’s manual, Holding fixtures for screw installation

1: Refer to Section 1.6.2 for details.

6 - 52 6 - 52
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection

CON A
1 Pin number Signal name
1 DA
LINK CABLE 2
2 DB 1 DA
(IN) 3
3 DG
4 2 DB
4 Empty
5
5 SLD CON A,B 3 DG
CON B
1
1 DA
4 Empty
LINK CABLE 2
(OUT) 2 DB 5 SLD
3
3 DG
4
4 Empty
1 (FG)
5
5 SLD 2 +24V (UNIT)
One-touch connector for communication CON C,D 3 24G (UNIT)
CON C 4 +24V(I/O)
1 Insulation
UNIT POWER CABLE(IN) 1 FG 5 24G(I/O)
2
2 +24V(UNIT)
3
3 24G(UNIT) Pin Signal Pin Signal
4
5
4 +24V(I/O) number name number name
5 24G(I/O)
I/O POWER CABLE(IN) 1 +24V 1 +24V
CON D CON CON
UNIT POWER CABLE(OUT)
1
1 FG 2 +V 2 Empty 1
2 +24V(UNIT)
1 9
2 3 24G 3 24G
3 (X0) (Y8)
3 24G(UNIT)
4
4 +24V(I/O) 4 X0 4 Y8
5
5 24G(I/O) 1 +24V 1 +24V
I/O POWER CABLE(OUT) CON CON
2 2 +V 2 Empty 1
One-touch connector for power supply and FG 2 10
3 24G 3 24G
3 CON1 Constant- (X1) (Y9)
voltage 4 X1 4 Y9
Brown 1 circuit
3-wire sensor 2 1 +24V 1 +24V
(source output) Blue 3 CON CON
Detection 2 +V 2 Empty 1
circuit Black 4 3 11
3 24G 3 24G
(X2) (YA)
4 X2 4 YA
CON8 1 +24V 1 +24V
1 CON CON
2 +V 2 Empty 1
2 4 12
3 3 24G 3 24G
(X3) (YB)
4
4 X3 4 YB
1 +24V 1 +24V
CON CON
2 +V 2 Empty 1
5 13
CON9 3 24G 3 24G
1
(X4) (YC)
4 X4 4 YC
2
3 1 +24V 1 +24V
Load 4 CON CON
2 +V 2 Empty 1
6 14
3 24G 3 24G
1 (X5) (YD)
4 X5 4 YD
CON16 1 +24V 1 +24V
1 CON CON
2 2 +V 2 Empty 1
3
7 15
3 24G 3 24G
Load 4 (X6) (YE)
4 X6 4 YE
1 +24V 1 +24V
CON CON
2 +V 2 Empty 1
8 16
1: Since all No.2 pins of CON9 to CON16 are connected inside the module, they cannot be used. 3 24G 3 24G
(X7) (YF)
2: Attach an unwired connector plug to an unused one-touch connector for power supply and FG. 4 X7 4 YF
3: Wiring the sensor connector (e-CON) incorrectly may cause malfunction or failure due to short circuit of the
power supply.

6 - 53 6 - 53
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection

<When using online connectors>

Online connector
for communication
CON A
1
1 DA
LINK CABLE 2
(IN) 2 DB
3
3 DG
4
4
5
5 SLD
CON B
1
1 DA
LINK CABLE 2
(OUT) 2 DB
3
3 DG
4
4
5
5 SLD
One-touch connector
for communication
CON C
1
UNIT POWER CABLE(IN) 1 FG
2
2 +24V(UNIT)
3
3 24G(UNIT)
4
4 +24V(I/O)
5
5 24G(I/O)
I/O POWER CABLE(IN) CON D
1
1 FG
2
UNIT POWER 2 +24V(UNIT)
CABLE(OUT) 3
3 24G(UNIT)
4
I/O POWER 4 +24V(I/O)
CABLE(OUT) 5
5 24G(I/O)

One-touch connector for power

supply and FG *1 Online connector
for power supply
and FG

1: Attach an unwired connector plug to an unused one-touch connector for power supply and FG.
Pin layout

Viewed from the front of the module

6 - 54 6 - 54
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.3.3 AJ65VBTCE32-32DT combined module

Type DC input transistor output combined module

Item AJ65VBTCE32-32DT Appearance
Input Output
Number of input points 16 points Number of output points 16 points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 24VDC
Operating load voltage 19.2 to 26.4VDC
Rated input current Approx. 5mA
range (ripple ratio: within 5%)
19.2 to 26.4VDC
Operating voltage range Max. load current 0.1A/point, 1.6A/common
(ripple ratio: within 5%)
Max. number of
100% Max. inrush current 0.7A, 10ms or less
simultaneous input points
14VDC or higher/3.5mA or
ON voltage/ON current Leakage current at OFF 0.1mA or lower
higher
OFF voltage/OFF current 6VDC or lower/1.7mA or lower 0.1VDC or lower (TYP.) 0.1A,
Max. voltage drop at ON
Input resistance Approx. 4.7kΩ 0.2VDC or lower (MAX.) 0.1A
OFF→ON 1.5ms or less (at 24VDC) Output type Sink type
Response
time Overload protection, overvoltage
ON→OFF 1.5ms or less (at 24VDC) Protection function
protection, overheat protection
Response OFF→ON 1ms or less
time ON→OFF 1ms or less (resistive load)

1F
F
19.2 to 26.4VDC
External Voltage

1E
E
(ripple ratio: within 5%)
power

1D
D
10mA or lower
supply for

1C
C
Current (at 24VDC and all points ON),
output part

1B
B
excluding external load current

1A
A
Input type Positive common (sink type) Surge suppressor Zener diode

19
9
Supply current for connected

AJ65VBTCE32-32DT
1.0A or lower/common

18
8
device

17
7
32 points/common

16
Wiring method for common

6
(input: 3-wire sensor connector (e-CON) type, output: 2-wire sensor connector (e-CON) type)

15
5
Number of occupied stations 32-point assignment/station (32 points used)

14
4
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

13
3
supply Current 45mA or lower (at 24VDC and all points ON)

12
2
Noise voltage 500Vp-p, noise width 1µs,

11
1
Noise immunity
noise frequency 25 to 60Hz (DC type noise simulator condition)

10
0
X

Y
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
10MΩ or higher between all DC external terminals and ground (500VDC insulation resistance

D
8 9 A B C D E F
0 1 2 3 4 5 6 7

Insulation resistance
tester)
PW L RUN L ERR.

C
Protection degree IP1XB

B
Weight 0.16kg
ON

B RATE STATI ON NO.

1 2 4 1 2 4 8 102040

One-touch connector for communication [Transmission circuit]

CON A

Communication
5-pin IDC plug is sold separately: A6CON-L5P
part
<Optional> Online connector for communication: A6CON-LJ5P
External One-touch connector for power supply and FG
connection Power supply [Module power supply, I/O power supply, FG]
system part 5-pin IDC plug is sold separately: A6CON-PW5P, A6CON-PW5P-SOD
<Optional> Online connector for power supply: A6CON-PWJ5P
Sensor connector (e-CON) [I/O signals]
I/O part
4-pin IDC plug is sold separately. 1
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Connector for Applicable cable:
communication FANC-110SBH, FA-CBL200PSBH, CS-110
2
0.66 to 0.98mm (AWG18)
Connector for
[φ2.2 to 3.0mm (A6CON-PW5P), φ2.0 to 2.3mm (A6CON-PW5P-SOD)]
Applicable power supply
Wire diameter: 0.16mm or more
wire size and FG
Insulating coating material: PVC (heat-resistant)
Sensor connector (e-CON).
Connector for
Applicable connector plugs are sold separately. 1
I/O
(applicable wire size: 0.08 to 0.5mm2, depending on the connector plug)
Accessory User’s manual, Holding fixtures for screw installation

1: Refer to Section 1.6.2 for details.

6 - 55 6 - 55
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection

Pin number Signal name Pin number Signal name

1 DA 1 (FG)
2 DB 2 +24V (UNIT)
CON CON
A,B 3 DG C,D 3 24G (UNIT)
4 Empty 4 +24V(I/O)
5 SLD 5 24G(I/O)
Pin number Signal name Pin number Signal name
1 +24V 1 +24V
CON1 2 +V CON17 2 Empty 1
(X0) 3 24G (Y10) 3 Empty 2
4 X0 4 Y10
1 +24V 1 +24V
CON2 2 +V CON18 2 Empty 1
(X1) 3 24G (Y11) 3 Empty 2
CONA
1
1 DA
4 X1 4 Y11
LINK CABLE 2
(IN) 3
2 DB 1 +24V 1 +24V
3 DG
4
4 Empty CON3 2 +V CON19 2 Empty 1
5
5 SLD (X2) 3 24G (Y12) 3 Empty 2
CONB
1
1 DA
4 X2 4 Y12
LINK CABLE 2
2 DB 1 +24V 1 +24V
(OUT) 3
3 DG
4
4 Empty
CON4 2 +V CON20 2 Empty 1
5
5 SLD (X3) 3 24G (Y13) 3 Empty 2
One-touch connector for communication 4 X3 4 Y13
CONC Insulation
1 +24V 1 +24V
1
UNIT POWER CABLE(IN) 1 FG
CON5 2 +V CON21 2 Empty 1
2 +24V(UNIT)
2
3
3 24G(UNIT) (X4) 3 24G (Y14) 3 Empty 2
4
4 +24V(I/O)
5
5 24G(I/O)
4 X4 4 Y14
I/O POWER CABLE(IN) COND 1 +24V 1 +24V
1
UNIT POWER CABLE(OUT)
2
1 FG CON6 2 +V CON22 2 Empty 1
2 +24V(UNIT)
3
3 24G(UNIT)
(X5) 3 24G (Y15) 3 Empty 2
4
+24V(I/O)
5
4
5 24G(I/O)
4 X5 4 Y15
I/O POWER CABLE(OUT) 1 +24V 1 +24V
3
One-touch connector for power supply and FG
CON1
Constant-voltage circuit CON7 2 +V CON23 2 Empty 1
4
Brown 1
(X6) 3 24G (Y16) 3 Empty 2
3-wire sensor
(sink output) Blue
2
3
4 X6 4 Y16
Detection
circuit Black 4 1 +24V 1 +24V
CON8 2 +V CON24 2 Empty 1
(X7) 3 24G (Y17) 3 Empty 2
CON16
1 4 X7 4 Y17
2 1 +24V 1 +24V
3
4 CON9 2 +V CON25 2 Empty 1
(X8) 3 24G (Y18) 3 Empty 2
CON17 4 X8 4 Y18
1
2
1 +24V 1 +24V
3 CON10 2 +V CON26 2 Empty 1
Load 4 (X9) 3 24G (Y19) 3 Empty 2
2 1
4 X9 4 Y19
1 +24V 1 +24V
CON32
1
CON11 2 +V CON27 2 Empty 1
2 (XA) 3 24G (Y1A) 3 Empty 2
3
Load 4 4 XA 4 Y1A
1 +24V 1 +24V
CON12 2 +V CON28 2 Empty 1
(XB)
3 24G (Y1B) 3 Empty 2
4 XB 4 Y1B
1 +24V 1 +24V
CON13 2 +V CON29 2 Empty 1
(XC) 3 24G (Y1C) 3 Empty 2
4 XC 4 Y1C
1 +24V 1 +24V
CON14 2 +V CON30 2 Empty 1
(XD) 3 24G (Y1D) 3 Empty 2
4 XD 4 Y1D
1 +24V 1 +24V
CON15 2 +V CON31 2 Empty 1
(XE) 3 24G (Y1E) 3 Empty 2
1: Since all No.2 pins of CON17 to CON32 are connected inside the module, they cannot be used.
4 XE 4 Y1E
2: Since all No.3 pins of CON17 to CON32 are connected inside the module, they cannot be used.
1 +24V 1 +24V
3: Attach an unwired connector plug to an unused one-touch connector for power supply and FG. CON16 2 +V CON32 2 Empty 1
4: Wiring the sensor connector (e-CON) incorrectly may cause malfunction or failure due to short (XF) 3 24G (Y1F) 3 Empty 2
circuit of the power supply. 4 XF 4 Y1F

6 - 56 6 - 56
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection

<When using online connectors>

Online connector
for communication
CONA
1
1 DA
LINK CABLE 2
(IN) 2 DB
3
3 DG
4
4
5
5 SLD
CONB
1
1 DA
LINK CABLE 2
(OUT) 2 DB
3
3 DG
4
4
5
5 SLD
One-touch connector
for communication
CONC
1
UNIT POWER CABLE(IN) 1 FG
2
2 +24V(UNIT)
3
3 24G(UNIT)
4
4 +24V(I/O)
5
5 24G(I/O)
I/O POWER CABLE(IN) COND
1
1 FG
2
UNIT POWER 2 +24V(UNIT)
CABLE(OUT) 3
3 24G(UNIT)
4
I/O POWER 4 +24V(I/O)
CABLE(OUT) 5
5 24G(I/O)

One-touch connector for power

supply and FG *1 Online connector
for power supply
and FG

1: Attach an unwired connector plug to an unused one-touch connector for power supply and FG.
Pin layout

Viewed from the front of the module

6 - 57 6 - 57
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.3.4 AJ65VBTCE3-32DTE combined module

Type DC input transistor output combined module

Item AJ65VBTCE3-32DTE Appearance
Input Output
Number of input points 16 points Number of output points 16 points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 24VDC
Operating load voltage 19.2 to 26.4VDC
Rated input current Approx. 5mA
range (ripple ratio: within 5%)
19.2 to 26.4VDC
Operating voltage range Max. load current 0.1A/point, 1.6A/common
(ripple ratio: within 5%)
Max. number of
100% Max. inrush current 0.7A, 10ms or less
simultaneous input points
14VDC or higher/3.5mA or
ON voltage/ON current Leakage current at OFF 0.1mA or lower
higher
OFF voltage/OFF current 6VDC or lower/1.7mA or lower 0.1VDC or lower (TYP.) 0.1A,
Max. voltage drop at ON
Input resistance Approx. 4.7kΩ 0.2VDC or lower (MAX.) 0.1A
OFF→ON 1.5ms or less (at 24VDC) Output type Source type
Response
time Overload protection, overheat
ON→OFF 1.5ms or less (at 24VDC) Protection function
protection
Response OFF→ON 1ms or less
time ON→OFF 1ms or less (resistive load)
19.2 to 26.4VDC
External Voltage
(ripple ratio: within 5%)
power
11mA or lower
supply for
Current (at 24VDC and all points ON),
output part
excluding external load current
Input type Negative common (source type) Surge suppressor Zener diode
Supply current for connected
2.0A or lower/common
device
32 points/common
Wiring method for common
(input: 3-wire sensor connector (e-CON) type, output: 3-wire sensor connector (e-CON) type)
Number of occupied stations 32-point assignment/station (32 points used)
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
supply Current 45mA or lower (at 24VDC and all points ON)
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity
noise frequency 25 to 60Hz (DC type noise simulator condition)
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
10MΩ or higher between all DC external terminals and ground (500VDC insulation resistance
Insulation resistance
tester)
Protection degree IP1XB
Weight 0.16kg
One-touch connector for communication [Transmission circuit]
Communication
5-pin IDC plug is sold separately: A6CON-L5P
part
<Optional> Online connector for communication: A6CON-LJ5P
External One-touch connector for power supply and FG
connection Power supply [Module power supply, I/O power supply, FG]
system part 5-pin IDC plug is sold separately: A6CON-PW5P, A6CON-PW5P-SOD
<Optional> Online connector for power supply: A6CON-PWJ5P
Sensor connector (e-CON) [I/O signals]
I/O part
4-pin IDC plug is sold separately. 1
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Connector for Applicable cable:
communication FANC-110SBH, FA-CBL200PSBH, CS-110
2
0.66 to 0.98mm (AWG18)
Connector for
[φ2.2 to 3.0mm (A6CON-PW5P), φ2.0 to 2.3mm (A6CON-PW5P-SOD)]
Applicable power supply
Wire diameter: 0.16mm or more
wire size and FG
Insulating coating material: PVC (heat-resistant)
Sensor connector (e-CON).
Connector for
Applicable connector plugs are sold separately. 1
I/O
(applicable wire size: 0.08 to 0.5mm2, depending on the connector plug)
Accessory User’s manual, Holding fixtures for screw installation

1: Refer to Section 1.6.2 for details.

6 - 58 6 - 58
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection

Pin number Signal name Pin number Signal name

1 DA 1 (FG)
2 DB 2 +24V (UNIT)
CON CON
A,B 3 DG C,D 3 24G (UNIT)
4 Empty 4 +24V(I/O)
5 SLD 5 24G(I/O)
Pin number Signal name Pin number Signal name
1 +24V 1 +24V
CON1 2 +V CON17 2 Empty 1
(X0) 3 24G (Y10) 3 24G
CON A 4 X0 4 Y10
1
LINK CABLE 2
1 DA 1 +24V 1 +24V
2 DB
(IN) 3
3 DG CON2 2 +V CON18 2 Empty 1
4
4 Empty (X1) 3 24G (Y11) 3 24G
5
5 SLD
4 X1 4 Y11
CON B
1
1 DA 1 +24V 1 +24V
LINK CABLE 2
(OUT) 3
2 DB CON3 2 +V CON19 2 Empty 1
4
3 DG (X2) 3 24G (Y12) 3 24G
4 Empty
5
5 SLD 4 X2 4 Y12
One-touch connector for communication 1 +24V 1 +24V
CON C CON4 2 +V CON20 2 Empty 1
1 Insulation (X3) (Y13)
UNIT POWER CABLE(IN)
2
1 FG 3 24G 3 24G
2 +24V(UNIT)
3
3 24G(UNIT)
4 X3 4 Y13
4
4 +24V(I/O) 1 +24V 1 +24V
5
5 24G(I/O)
CON5 2 +V CON21 2 Empty 1
I/O POWER CABLE(IN) CON D
1 (X4) 3 24G (Y14) 3 24G
UNIT POWER CABLE(OUT) 1 FG
2
2 +24V(UNIT) 4 X4 4 Y14
3
3 24G(UNIT)
4 1 +24V 1 +24V
4 +24V(I/O)
5
5 24G(I/O) CON6 2 +V CON22 2 Empty 1
I/O POWER CABLE(OUT) (X5) 3 24G (Y15) 3 24G
2
One-touch connector for power supply and FG 4 X5 4 Y15
1 +24V 1 +24V
3 CON1 Constant-
voltage CON7 2 +V CON23 2 Empty 1
Brown 1
3-wire sensor circuit (X6) 3 24G (Y16) 3 24G
(source output) 2

Detection
Blue 3 4 X6 4 Y16
Black 4
circuit 1 +24V 1 +24V
CON8 2 +V CON24 2 Empty 1
(X7) 3 24G (Y17) 3 24G
CON16
1 4 X7 4 Y17
2
1 +24V 1 +24V
3
4 CON9 2 +V CON25 2 Empty 1
(X8) 3 24G (Y18) 3 24G
4 X8 4 Y18
1 +24V 1 +24V
CON17
CON10 2 +V CON26 2 Empty 1
1
2
(X9) 3 24G (Y19) 3 24G
Load
3 4 X9 4 Y19
4
1 +24V 1 +24V
1
CON11 2 +V CON27 2 Empty 1
(XA) 3 24G (Y1A) 3 24G
CON32
4 XA 4 Y1A
1
2 1 +24V 1 +24V
CON12 2 +V
3 CON28 2 Empty 1
Load 4 (XB)
3 24G (Y1B) 3 24G
4 XB 4 Y1B
1 +24V 1 +24V
CON13 2 +V CON29 2 Empty 1
(XC) 3 24G (Y1C) 3 24G
4 XC 4 Y1C
1 +24V 1 +24V
CON14 2 +V CON30 2 Empty 1
(XD) 3 24G (Y1D) 3 24G
4 XD 4 Y1D
1 +24V 1 +24V
CON15 2 +V CON31 2 Empty 1
1: Since all No.2 pins of CON17 to CON32 are connected inside the module, they cannot be used. (XE) 3 24G (Y1E) 3 24G
2: Attach an unwired connector plug to an unused one-touch connector for power supply and FG. 4 XE 4 Y1E
3: Wiring the sensor connector (e-CON) incorrectly may cause malfunction or failure due to short 1 +24V 1 +24V
circuit of the power supply. CON16 2 +V CON32 2 Empty 1
(XF) 3 24G (Y1F) 3 24G
4 XF 4 Y1F

6 - 59 6 - 59
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection

<When using online connectors>

Online connector
for communication
CON A
1
1 DA
LINK CABLE 2
(IN) 2 DB
3
3 DG
4
4
5
5 SLD
CON B
1
1 DA
LINK CABLE 2
(OUT) 2 DB
3
3 DG
4
4
5
5 SLD
One-touch connector
for communication
CON C
1
UNIT POWER CABLE(IN) 1 FG
2
2 +24V(UNIT)
3
3 24G(UNIT)
4
4 +24V(I/O)
5
5 24G(I/O)
I/O POWER CABLE(IN) CON D
1
1 FG
2
UNIT POWER 2 +24V(UNIT)
CABLE(OUT) 3
3 24G(UNIT)
4
I/O POWER 4 +24V(I/O)
CABLE(OUT) 5
5 24G(I/O)

One-touch connector for power

supply and FG *1 Online connector
for power supply
and FG

1: Attach an unwired connector plug to an unused one-touch connector for power supply and FG.
Pin layout

Viewed from the front of the module

6 - 60 6 - 60
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.4 One Touch Connector Type Combined Module

6.4.1 AJ65SBTC4-16DT combined module

Type DC input transistor output combined module

Item AJ65SBTC4-16DT Appearance
Input Output
Number of input points 8 points Number of output points 8 points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 24VDC
Operating load voltage 19.2 to 26.4VDC
Rated input current Approx. 5mA
range (ripple ratio: within 5%)
19.2 to 26.4VDC
Operating voltage range Max. load current 0.5A/point, 2.4A/common
(ripple ratio: within 5%)
Max. number of simultaneous input
100% Max. inrush current 1.0A 10ms or less
points
14VDC or
ON voltage/ON current higher/3.5mA or Leakage current at OFF 0.25mA or lower
higher
6VDC or lower/1.7mA 0.3VDC or lower (TYP.) 0.5A,
OFF voltage/OFF current Max. voltage drop at ON
or lower 0.6VDC or lower (MAX.) 0.5A
Input resistance Approx. 4.7kΩ Output type Sink type
1.5ms or less
OFF→ON
(at 24VDC) Overload protection, overvoltage
Response time Protection function
1.5ms or less protection, overheat protection
ON→OFF
(at 24VDC)
Response OFF→ON 0.5ms or less
time ON→OFF 1.5ms or less (resistive load)

ON

COM-
19.2 to 26.4VDC

CTL+
Voltage

B RATE
40 20 10 8 4 2 1 4 2 1
External (ripple ratio: within 5%)
power supply

+24V
24G
13mA or lower

YF
X7
STATION NO.
for output part Current (at 24VDC and all points ON),

+24V
24G
YE
X6
excluding external load current

+24V
24G
YD
X5
Positive common
Input type Surge suppressor Zener diode
(sink type)

+24V
24G
YC
X4
Supply current for connected device 1.0A or lower/common

+24V
24G
YB
X3
Y8 9 A B C D E F

Wiring method for common 16 points/common (4-wire, one-touch connector type)

+24V
24G
YA
A J65SBTC4-16DT
Number of occupied stations 32-point assignment/station (16 points used) X2

Voltage 20.4 to 26.4VDC (ripple ratio: within 5%) +24V

24G
X1
Y9

Module power supply

Current 40mA or lower (at 24VDC and all points ON)
+24V
24G
X0
Y8
X0 1 2 3 4 5 6 7

Noise voltage 500Vp-p, noise width 1µs,

Noise immunity
noise frequency 25 to 60Hz (DC type noise simulator condition)
(FG)
24G

Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
DA DG +24V

10MΩ or higher between all DC external terminals and ground (500VDC insulation
SLD

Insulation resistance
resistance tester)
DB

Protection degree IP2X

Weight 0.15kg
External 7-point two-piece terminal block [Transmission circuit, module power supply, FG]
Communication part,
connection M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
module power supply part
system Applicable solderless terminal: 2 or less
2-point direct-mount terminal block [I/O power supply]
I/O power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
Dedicated one-touch connector [I/O signals]
I/O part
4-pin IDC plug is sold separately.
M4 screw with plain washer finished round (tightening torque range: 0.78 to 1.08N•m)
Module mounting screw
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable Communication y RAV1.25-3 (compliant with JIS C 2805)
wire size part, [Applicable wire size: 0.3 to 1.25mm2]
Applicable
module power y V2-MS3, RAP2-3SL, TGV2-3N
solderless
supply part [Applicable wire size: 1.25 to 2.0mm2]
terminal
I/O power
supply part
I/O part φ1.0 to 1.4 (A6CON-P214), φ1.4 to 2.0 (A6CON-P220)
2
[Applicable wire size: 0.14 to 0.2mm ]
φ1.0 to 1.4 (A6CON-P514), φ1.4 to 2.0 (A6CON-P520)
[Applicable wire size: 0.3 to 0.5mm2]
Accessory User’s manual

6 - 61 6 - 61
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection
<Connection example of 4-, 3-, and 2-wire sensors> Terminal number Signal name
TB1 DA
TB2 DB
1 DA
2 DB TB3 DG
3 DG Insulation TB4 SLD
4 SLD
5 +24V TB5 +24V
6 FG TB6 (FG)
7 24G
Module power supply TB7 24G
Pin number Signal name
4-wire sensor 1 X0
CON1
(sink output/ 2 Y8
sink input) Detection
Black 1 CON1
circuit White 2 3 +24V
Brown 3 4 24G
Blue 4
1 X1
The cable colors are selected according to
2 Y9
IEC 60947-5-2 (JIS C 8201-5-2). CON2
3 +24V
4 24G
1 X2
3-wire sensor CON2
(sink output) 2 YA
Black 1 CON3
Detection
2 3 +24V
circuit
Brown 3 4 24G
Blue 4
1 X3
2 YB
CON4
3 +24V
4 24G
1 X4
2 YC
CON5
2-wire sensor CON8 3 +24V
(sink output) Brown 1
Detection
4 24G
2
circuit 3 1 X5
Blue 4 2 YD
CON6
3 +24V
4 24G
1 X6
2 YE
CON7
8 CTL+ 3 +24V
9 COM-
External power supply for output part Constant-voltage circuit 4 24G
1 X7
2 YF
<Connection example of other I/O devices> CON8
3 +24V
4 24G
1 DA
2 DB Terminal number Signal name
3 DG Insulation TB8 CTL+
4 SLD
5 +24V TB9 COM-
6 FG Pin layout
7 24G
Module power supply

CON1
1
2
3
4

Viewed from the front of the module

CON8
1
Load 2
3
4

8 CTL+
9 COM-
External power supply for output
Constant-voltage circuit

6 - 62 6 - 62
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.4.2 AJ65SBTC4-16DT2 combined module

Type DC input transistor output combined module
Item AJ65SBTC4-16DT2 Appearance
Input Output
Number of output
Number of input points 8 points 8 points
points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 24VDC
Operating load voltage 19.2 to 26.4VDC
Rated input current Approx. 5mA
range (ripple ratio: within 5%)
19.2 to 26.4VDC
Operating voltage range Max. load current 0.5A/point, 2.4A/common
(ripple ratio: within 5%)
Max. number of simultaneous input
100% Max. inrush current 1.0A, 10ms or less
points
14VDC or higher/ Leakage current at
ON voltage/ON current 0.1mA or lower
3.5mA or higher OFF
6VDC or lower/ Max. voltage drop at 0.3VDC or lower (TYP.) 0.5A,
OFF voltage/OFF current
1.7mA or lower ON 0.6VDC or lower (MAX.) 0.5A
Input resistance Approx. 4.7kΩ Output type Sink type
OFF→ON 1.5ms or less (at 24VDC) Protection function None
Response time
ON→OFF 1.5ms or less (at 24VDC) Response OFF→ON 0.5ms or less
time ON→OFF 1.5ms or less (resistive load)
19.2 to 26.4VDC
External Voltage
(ripple ratio: within 5%)
power

ON
13mA or lower

COM-
supply for

CTL+
B RATE
40 20 10 8 4 2 1 4 2 1
Current (at 24VDC and all points ON),
output part
excluding external load current

+24V
24G
YF
X7
STATION NO.
Input type Positive common (sink type) Surge suppressor Zener diode

+24V
24G
YE
X6
Supply current for connected device 1.0A or lower/common

+24V
24G
YD
X5
Wiring method for common 16 points/common (4-wire, one-touch connector type)

24G
+24V
YC
X4
Number of occupied stations 32-point assignment/station (16 points used)

+24V
24G
YB
X3
Y8 9 A B C D E F
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
Module power supply

A J65SBTC4-16DT2

+24V
24G
YA
X2
Current 40mA or lower (at 24VDC and all points ON)

+24V
24G
Noise voltage 500Vp-p, noise width 1µs,

X1
Y9
Noise immunity
noise frequency 25 to 60Hz (DC type noise simulator condition)

+24V
24G
X0
Y8
X0 1 2 3 4 5 6 7

Withstand voltage 500VAC for 1 minute between all DC external terminals and ground (FG)
24G

10MΩ or higher between all DC external terminals and ground (500VDC insulation
Insulation resistance
DA DG +24V

resistance tester)
SLD

Protection degree IP2X

DB

Weight 0.15kg
External 7-point two-piece terminal block [Transmission circuit, module power supply, FG]
Communication part,
connection M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
module power supply part
system Applicable solderless terminal: 2 or less
2-point direct-mount terminal block [I/O power supply]
I/O power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
Dedicated one-touch connector [I/O signals]
I/O part
4-pin IDC plug is sold separately.
M4 screw with plain washer finished round (tightening torque range: 0.78 to 1.08N•m)
Module mounting screw
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable Communication y RAV1.25-3 (compliant with JIS C 2805)
wire size part, [Applicable wire size: 0.3 to 1.25mm2]
Applicable
module power y V2-MS3, RAP2-3SL, TGV2-3N
solderless
supply part [Applicable wire size: 1.25 to 2.0mm2]
terminal
I/O power
supply part
φ1.0 to 1.4 (A6CON-P214), φ1.4 to 2.0 (A6CON-P220)
[Applicable wire size: 0.14 to 0.2mm2]
I/O part
φ1.0 to 1.4 (A6CON-P514), φ1.4 to 2.0 (A6CON-P520)
[Applicable wire size: 0.3 to 0.5mm2]
Accessory User’s manual

6 - 63 6 - 63
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection
<Connection example of 4-, 3-, and 2-wire sensors > Terminal number Signal name
TB1 DA
1 DA TB2 DB
2 DB
3 DG TB3 DG
Insulation
4 SLD
5 +24V
TB4 SLD
6 FG TB5 +24V
7 24G
Module power supply
TB6 (FG)
TB7 24G
4-wire sensor
(sink output/ CON1 Pin number Signal name
sink input) Detection Black 1
White 2
1 X0
circuit
Brown 3 2 Y8
Blue 4 CON1
3 +24V
The cable colors are selected according to
IEC 60947-5-2 (JIS C 8201-5-2). 4 24G
1 X1
2 Y9
3-wire sensor
CON2
CON2
(sink output) 3 +24V
Black 1
Detection
circuit 2 4 24G
Brown 3
Blue 4 1 X2
2 YA
CON3
3 +24V
4 24G
1 X3
2-wire sensor CON8 2 YB
CON4
(sink output) Brown 1 3 +24V
Detection 2
circuit 3 4 24G
Blue 4
1 X4
2 YC
CON5
3 +24V
4 24G
8 CTL+ 1 X5
9 COM-
External power supply for output part Constant-voltage circuit
2 YD
CON6
3 +24V
< Connection example of other I/O devices >
4 24G
1 X6
1 DA
2 DB 2 YE
CON7
3 DG Insulation 3 +24V
4 SLD
5 +24V 4 24G
6 FG
7 24G 1 X7
Module power supply
2 YF
CON8
3 +24V
CON1 4 24G
1
Terminal number Signal name
2
3 TB8 CTL+
4
TB9 COM-
Pin layout

CON8
1
Load 2
3
4
Viewed from the front of the module

8 CTL+
9 COM-
External power supply for output Constant-voltage circuit

6 - 64 6 - 64
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.4.3 AJ65SBTC1-32DT combined module

Type DC input transistor output combined module

Item AJ65SBTC1-32DT Appearance
Input Output
Number of output
Number of input points 16 points 16 points
points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 24VDC
Operating load voltage 19.2 to 26.4VDC
Rated input current Approx. 5mA
range (ripple ratio: within 5%)
19.2 to 26.4VDC
Operating voltage range Max. load current 0.1A/point, 1.6A/common
(ripple ratio: within 5%)
Max. number of simultaneous input
100% Max. inrush current 1.0A, 10ms or less
points
14VDC or Leakage current at
ON voltage/ON current 0.25mA or lower
higher/3.5mA or higher OFF
6VDC or lower/ Max. voltage drop at 0.3VDC or lower (TYP.) 0.1A,
OFF voltage/OFF current
1.7mA or lower ON 0.6VDC or lower (MAX.) 0.1A
Input resistance Approx. 4.7kΩ Output type Sink type
1.5ms or less Overload protection, overvoltage
OFF→ON Protection function
(at 24VDC) protection, overheat protection
Response time
1.5ms or less Response OFF→ON 0.5ms or less
ON→OFF
(at 24VDC) time ON→OFF 1.5ms or less (resistive load)

ON
19.2 to 26.4VDC

COM-
External Voltage

COM+
(ripple ratio: within 5%)

B RATE
40 20 10 8 4 2 1 4 2 1
power
17mA or lower

Y1C
Y1D
Y1E
Y1F
supply for

STATION NO.
Current (at 24VDC and all points ON),
output part

Y1A
Y1B
Y18
Y19
excluding external load current
Positive common

Y14
Y15
Y16
Y17
Input type Surge suppressor Zener diode
(sink type)

Y10-Y1F
X0-XF

Y10
Y11
Y12
Y13
Wiring method for common 32 points/common (1-wire, one-touch connector type)

XC
XD
XE
XF
Y101112 1314 1516 17 Y1819 1A1B1C1D1E1F
Number of occupied stations 32-point assignment/station (32 points used) X8 9 A B C D E F

XA
XB
X8
X9
A J65SBTC1-32DT
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
Module power supply
Current 50mA or lower (at 24VDC and all points ON)
X4
X5
X6
X7
Noise voltage 500Vp-p, noise width 1µs, X0
X1
X2
Noise immunity X3
X0 1 2 3 4 5 6 7

noise frequency 25 to 60Hz (DC type noise simulator condition)

Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
(FG)
24G

10MΩ or higher between all DC external terminals and ground (500VDC insulation
DA DG +24V

Insulation resistance
SLD

resistance tester)
Weight 0.16kg
DB

External 7-point two-piece terminal block [Transmission circuit, module power supply, FG]
Communication part,
connection M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
module power supply part
system Applicable solderless terminal: 2 or less
2-point direct-mount terminal block [I/O power supply]
I/O power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
I/O part Dedicated one-touch connector [I/O signals] 4-pin IDC plug is sold separately.
Module mounting screw M4 screw with plain washer finished round
(tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable Communication y RAV1.25-3 (compliant with JIS C 2805)
wire size part, [Applicable wire size: 0.3 to 1.25mm2]
Applicable
module power y V2-MS3, RAP2-3SL, TGV2-3N
solderless
supply part [Applicable wire size: 1.25 to 2.0mm2]
terminal
I/O power
supply part
I/O part φ1.0 to 1.4 (A6CON-P214), φ1.4 to 2.0 (A6CON-P220)
2
[Applicable wire size: 0.14 to 0.2mm ]
φ1.0 to 1.4 (A6CON-P514), φ1.4 to 2.0 (A6CON-P520)
[Applicable wire size: 0.3 to 0.5mm2]
Accessory User’s manual

6 - 65 6 - 65
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection
Terminal Signal
number name
TB1 DA
TB2 DB
TB3 DG
TB4 SLD
TB5 +24V
1 DA TB6 (FG)
2 DB TB7 24G
3 DG Insulation Signal
4 SLD Pin number
5 +24V
name
6 FG 1 X0
7 24G 2 X1
Module power supply CON1
CON1 to CON4 3 X2
1
4 X3
2
3 1 X4
4 2 X5
CON2
3 X6
4 X7
1 X8
2 X9
CON5 to CON8 CON3
Load 3 XA
1
2 4 XB
3 1 XC
Load
4
2 XD
CON4
3 XE
4 XF
1 Y10
2 Y11
CON5
External power 3 Y12
supply for 4 Y13
output part 1 Y14
2 Y15
8 COM+ CON6
9 COM- 3 Y16
Constant-voltage circuit
4 Y17
Load power supply
1 Y18
Load
2 Y19
External power supply for output part CON7
3 Y1A
and load power supply (common)
8 COM+ 4 Y1B
9 COM-
1 Y1C
2 Y1D
CON8
3 Y1E
4 Y1F
Terminal Signal
number name
TB8 COM+
TB9 COM-
Pin layout

Viewed from the front of the module

6 - 66 6 - 66
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.4.4 AJ65SBTC1-32DT1 combined module

Type DC input transistor output combined module

Item AJ65SBTC1-32DT1 Appearance
Input Output
Number of output
Number of input points 16 points 16 points
points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 24VDC
Operating load voltage 19.2 to 26.4VDC
Rated input current Approx. 5mA
range (ripple ratio: within 5%)
19.2 to 26.4VDC
Operating voltage range Max. load current 0.1A/point, 1.6A/common
(ripple ratio: within 5%)
Max. number of simultaneous input
100% Max. inrush current 1.0A, 10ms or less
points
15VDC or higher/ Leakage current at
ON voltage/ON current 0.25mA or lower
3mA or higher OFF
3VDC or lower/ Max. voltage drop at 0.3VDC or lower (TYP.) 0.1A,
OFF voltage/OFF current
0.5mA or lower ON 0.6VDC or lower (MAX.) 0.1A
Input resistance Approx. 4.7kΩ Output type Sink type
0.2ms or less Overload protection, overvoltage
OFF→ON Protection function
(at 24VDC) protection, overheat protection
Response time
0.2ms or less Response OFF→ON 0.5ms or less
ON→OFF
(at 24VDC) time ON→OFF 1.5ms or less (resistive load)
19.2 to 26.4VDC
External Voltage
(ripple ratio: within 5%)

ON
power

COM-
COM+
17mA or lower

B RATE
supply for

40 20 10 8 4 2 1 4 2 1
Current (at 24VDC and all points ON),
output part

Y1C
Y1D
Y1E
Y1F
excluding external load current

STATION NO.

Y1A
Y1B
Positive common

Y18
Y19
Input type Surge suppressor Zener diode
(sink type)

Y14
Y15
Y16
Y17
Wiring method for common 32 points/common (1-wire, one-touch connector type)

Y10-Y1F
X0-XF

Y10
Y11
Y12
Y13
Number of occupied stations 32-point assignment/station (32 points used)

XC
XD
XE
XF
Y1011 12 1314 1516 17 Y1819 1A1B1C1D1E1F
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
Module power supply X8 9 A B C D E F
Current 50mA or lower (at 24VDC and all points ON)

A J65SBTC1-32DT1

XA
XB
X8
X9
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity
X4
X5
X6
X7
noise frequency 25 to 60Hz (DC type noise simulator condition) X0
X1
X2
X3
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
X0 1 2 3 4 5 6 7

10MΩ or higher between all DC external terminals and ground (500VDC insulation
Insulation resistance
(FG)
24G

resistance tester)
DA DG +24V

Protection degree IP2X

SLD

Weight 0.16kg
DB

External 7-point two-piece terminal block [Transmission circuit, module power supply, FG]
Communication part,
connection M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
module power supply part
system Applicable solderless terminal: 2 or less
2-point direct-mount terminal block [I/O power supply]
I/O power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
I/O part Dedicated one-touch connector [I/O signals] 4-pin IDC plug is sold separately.
Module mounting screw M4 screw with plain washer finished round
(tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable Communication y RAV1.25-3 (compliant with JIS C 2805)
2
wire size part, [Applicable wire size: 0.3 to 1.25mm ]
Applicable
module power y V2-MS3, RAP2-3SL, TGV2-3N
solderless 2
supply part [Applicable wire size: 1.25 to 2.0mm ]
terminal
I/O power
supply part
I/O part φ1.0 to 1.4 (A6CON-P214),
φ1.4 to 2.0 (A6CON-P220)
2
[Applicable wire size: 0.14 to 0.2 mm ]
φ1.0 to 1.4 (A6CON-P514),
φ1.4 to 2.0 (A6CON-P520)
2
[Applicable wire size: 0.3 to 0.5 mm ]
Accessory User’s manual

6 - 67 6 - 67
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection
Terminal Signal
number name
TB1 DA
TB2 DB
TB3 DG
TB4 SLD
1 DA
TB5 +24V
2 DB TB6 (FG)
3 DG TB7 24G
Insulation
4 SLD
Signal
5 +24V Pin number
name
6 FG
7 24G 1 X0
Module power supply
CON1 to CON4 2 X1
CON1
1 3 X2
2 4 X3
3
1 X4
4
2 X5
CON2
3 X6
4 X7
1 X8
CON5 to CON8 2 X9
CON3
Load 1 3 XA
2 4 XB
3
Load
1 XC
4
2 XD
CON4
3 XE
4 XF
1 Y10
2 Y11
CON5
3 Y12
External power
supply for 4 Y13
output part 1 Y14
2 Y15
8 COM+ CON6
3 Y16
9 COM-
Constant-voltage circuit 4 Y17
Load power supply 1 Y18
2 Y19
Load
CON7
3 Y1A
External power supply for output part 4 Y1B
8 COM+ and load power supply (common)
1 Y1C
9 COM-
2 Y1D
CON8
3 Y1E
4 Y1F
Terminal Signal
number name
TB8 COM+
TB9 COM-
Pin layout

Viewed from the front of the module

6 - 68 6 - 68
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.4.5 AJ65SBTC1-32DT2 combined module

Type DC input transistor output combined module
Item AJ65SBTC1-32DT2 Appearance
Input Output
Number of input points 16 points Number of output points 16 points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 24VDC
Operating load voltage 19.2 to 26.4VDC
Rated input current Approx. 5mA
range (ripple ratio: within 5%)
19.2 to 26.4VDC
Operating voltage range Max. load current 0.1A/point, 1.6A/common
(ripple ratio: within 5%)
Max. number of simultaneous input
100% Max. inrush current 1.0A, 10ms or less
points
14VDC or higher/
ON voltage/ON current Leakage current at OFF 0.1mA or lower
3.5mA or higher
6VDC or lower/ 0.3VDC or lower (TYP.) 0.1A,
OFF voltage/OFF current Max. voltage drop at ON
1.7mA or lower 0.6VDC or lower (MAX.) 0.1A
Input resistance Approx. 4.7kΩ Output type Sink type
1.5ms or less
OFF→ON Protection function None
(at 24VDC)
Response time
1.5ms or less
ON→OFF Response OFF→ON 0.5ms or less
(at 24VDC)
time
ON→OFF 1.5ms or less (resistive load)
19.2 to 26.4VDC
External Voltage
(ripple ratio: within 5%)

ON
power

COM-
17mA or lower

COM+
supply for

B RATE
40 20 10 8 4 2 1 4 2 1
Current (at 24VDC and all points ON),
output part

Y1C
Y1D
Y1E
Y1F
excluding external load current

STATION NO.

Y1A
Y1B
Positive common

Y18
Y19
Input type Surge suppressor Zener diode
(sink type)

Y14
Y15
Y16
Y17
Wiring method for common 32 points/common (1-wire, one-touch connector type)

Y10-Y1F
X0-XF

Y10
Y11
Y12
Y13
Number of occupied stations 32-point assignment/station (32 points used)

XC
XD
XE
XF
Y1011 12 1314 1516 17 Y18 191A1B1C1D1E1F
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
X8 9 A B C D E F
Module power supply
Current 50mA or lower (at 24VDC and all points ON)

A J65SBTC1-32DT2

XA
XB
X8
X9
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity
X4
X5
X6
X7
noise frequency 25 to 60Hz (DC type noise simulator condition)
X0
X1
X2
X3
X0 1 2 3 4 5 6 7

Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
10MΩ or higher between all DC external terminals and ground (500VDC insulation
(FG)

Insulation resistance
24G

resistance tester)
+24V

Protection degree IP2X

SLD

Weight 0.16kg
DG
DB
DA

External 7-point two-piece terminal block

connection Communication part, [Transmission circuit, module power supply, FG]
system module power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
2-point direct-mount terminal block
[I/O power supply]
I/O power supply part
M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
I/O part Dedicated one-touch connector [I/O signals] 4-pin IDC plug is sold separately.
M4 screw with plain washer finished round
Module mounting screw (tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable Communication y RAV1.25-3 (compliant with JIS C 2805)
2
wire size part, module [Applicable wire size: 0.3 to 1.25mm ]
Applicable
power supply y V2-MS3, RAP2-3SL, TGV2-3N
solderless 2
part [Applicable wire size: 1.25 to 2.0mm ]
terminal
I/O power supply
part
I/O part φ1.0 to 1.4 (A6CON-P214), φ1.4 to 2.0 (A6CON-P220)
2
[Applicable wire size: 0.14 to 0.2mm ]
φ1.0 to 1.4 (A6CON-P514), φ1.4 to 2.0 (A6CON-P520)
2
[Applicable wire size: 0.3 to 0.5mm ]
Accessory User’s manual

6 - 69 6 - 69
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection
Terminal Signal
number name
TB1 DA
TB2 DB
TB3 DG
TB4 SLD
TB5 +24V
1 DA TB6 (FG)
2 DB TB7 24G
3 DG Insulation
4 SLD
Signal
Pin number
5 +24V name
6 FG 1 X0
7 24G
Module power supply 2 X1
CON1 to CON4 CON1
3 X2
1
2 4 X3
3 1 X4
4 2 X5
CON2
3 X6
4 X7
1 X8
CON5 to CON8 2 X9
Load
CON3
1 3 XA
2 4 XB
3
Load
4
1 XC
2 XD
CON4
3 XE
4 XF
1 Y10
2 Y11
External power CON5
3 Y12
supply for output
part 4 Y13
1 Y14
8 COM+ 2 Y15
9 COM- CON6
Constant-voltage circuit 3 Y16
Load power supply 4 Y17
1 Y18
Load
External power supply for output part 2 Y19
CON7
and load power supply (common) 3 Y1A
8 COM+
9 COM- 4 Y1B
1 Y1C
2 Y1D
CON8
3 Y1E
4 Y1F
Terminal Signal
number name
TB8 COM+
TB9 COM-
Pin layout

Viewed from the front of the module

6 - 70 6 - 70
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.4.6 AJ65SBTC1-32DT3 combined module

Type DC input transistor output combined module

Item AJ65SBTC1-32DT3 Appearance
Input Output
Number of output
Number of input points 16 points 16 points
points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 24VDC
Operating load voltage 19.2 to 26.4VDC
Rated input current Approx. 5mA
range (ripple ratio: within 5%)
19.2 to 26.4VDC
Operating voltage range Max. load current 0.1A/point, 1.6A/common
(ripple ratio: within 5%)
Max. number of simultaneous input
100% Max. inrush current 1.0A, 10ms or less
points
15VDC or higher/ Leakage current at
ON voltage/ON current 0.1mA or lower
3mA or higher OFF
3VDC or lower/ Max. voltage drop at 0.3VDC or lower (TYP.) 0.1A,
OFF voltage/OFF current
0.5mA or lower ON 0.6VDC or lower (MAX.) 0.1A
Input resistance Approx. 4.7kΩ Output type Sink type
0.2ms or less
OFF→ON Protection function None
(at 24VDC)
Response time
0.2ms or less
ON→OFF Response OFF→ON 0.5ms or less
(at 24VDC)
time
ON→OFF 1.5ms or less (resistive load)
Voltage 19.2 to 26.4VDC

ON

COM-
External

COM+
(ripple ratio: within 5%)

B RATE
40 20 10 8 4 2 1 4 2 1
power
supply for Current 17mA or lower

Y1C
Y1D
Y1E
Y1F
(at 24VDC and all points ON),

STATION NO.
output part

Y1A
Y1B
Y18
Y19
excluding external load current
Positive common

Y14
Y15
Y16
Y17
Input type Surge suppressor Zener diode
(sink type)

Y10-Y1F
X0-XF

Y10
Y11
Y12
Y13
Wiring method for common 32 points/common (1-wire, one-touch connector type)

XC
XD
XE
XF
Y1011 12 13141516 17 Y18191A1B1C1D1E1F
Number of occupied stations 32-point assignment/station (32 points used)
X8 9 A B C D E F
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)

A J65SBTC1-32DT3

XA
XB
X8
X9
Module power supply
Current 50mA or lower (at 24VDC and all points ON)

X4
X5
X6
X7
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity X0
X1
X2
X3
noise frequency 25 to 60Hz (DC type noise simulator condition)
X0 1 2 3 4 5 6 7

Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
(FG)
24G

10MΩ or higher between all DC external terminals and ground (500VDC insulation
Insulation resistance
resistance tester)
+24V
SLD

Protection degree IP2X

DG
DB

Weight 0.16kg
DA

External 7-point two-piece terminal block

connection Communication part, [Transmission circuit, module power supply, FG]
system module power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
2-point direct-mount terminal block
[I/O power supply]
I/O power supply part
M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
I/O part Dedicated one-touch connector [I/O signals] 4-pin IDC plug is sold separately.
Module mounting screw M4 screw with plain washer finished round (tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable Communication y RAV1.25-3 (compliant with JIS C 2805)
2
wire size part, [Applicable wire size: 0.3 to 1.25mm ]
Applicable
module power y V2-MS3, RAP2-3SL, TGV2-3N
solderless 2
supply part [Applicable wire size: 1.25 to 2.0mm ]
terminal
I/O power
supply part
I/O part φ1.0 to 1.4 (A6CON-P214), φ1.4 to 2.0 (A6CON-P220)
2
[Applicable wire size: 0.14 to 0.2mm ]
φ1.0 to 1.4 (A6CON-P514), φ1.4 to 2.0 (A6CON-P520)
2
[Applicable wire size: 0.3 to 0.5mm ]
Accessory User’s manual

6 - 71 6 - 71
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection
Terminal
Signal name
number
TB1 DA
TB2 DB
TB3 DG
TB4 SLD
TB5 +24V
1 DA
2 DB TB6 (FG)
3 DG Insulation TB7 24G
4 SLD
Pin number Signal name
5 +24V
6 FG 1 X0
7 24G 2 X1
Module power supply CON1
CON1 to CON4 3 X2
1 4 X3
2
1 X4
3
4 2 X5
CON2
3 X6
4 X7
1 X8
2 X9
CON5 to CON8 CON3
Load 3 XA
1
2 4 XB
3 1 XC
Load
4 2 XD
CON4
3 XE
4 XF
1 Y10
2 Y11
CON5
External power 3 Y12
supply for output 4 Y13
part 1 Y14
2 Y15
8 COM+ CON6
9 COM- 3 Y16
Constant-voltage circuit
4 Y17
Load power supply
1 Y18
2 Y19
Load CON7
3 Y1A
External power supply for output part
4 Y1B
8 COM+ and load power supply (common)
1 Y1C
9 COM-
2 Y1D
CON8
3 Y1E
4 Y1F
Terminal
Signal name
number
TB8 COM+
TB9 COM-
Pin layout

Viewed from the front of the module

6 - 72 6 - 72
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.5 FCN Connector Type Combined Module

6.5.1 AJ65SBTCF1-32DT combined module

Type DC input transistor output combined module
Item AJ65SBTCF1-32DT Appearance
Input Output
Number of output
Number of input points 16 points 16 points
points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 12/24VDC
Operating load voltage 10.2 to 26.4VDC
Rated input current Approx. 5mA
range (ripple ratio: within 5%)
0.1A/point
19.2 to 26.4VDC
Operating voltage range Max. load current (at all points ON: 0.1A/point),
(ripple ratio: within 5%)
1.6A/common
Max. number of simultaneous input
100% Max. inrush current 1.0A, 10ms or less
points
14VDC or higher/ Leakage current at
ON voltage/ON current 0.1mA or lower
3.5mA or higher OFF
6VDC or lower/ Max. voltage drop at 0.1VDC or lower (TYP.) 0.1A,
OFF voltage/OFF current
1.7mA or lower ON 0.2VDC or lower (MAX.) 0.1A
Input resistance Approx. 4.7kΩ Output type Sink type
Overload protection, overvoltage
Protection function
protection, overheat protection
1.5ms or less Response OFF→ON 0.5ms or less

ON
OFF→ON
(at 24VDC) time ON→OFF 1.5ms or less (resistive load)
Response time

X8 X9 XA XB XC XD XE XF COM NC Y18 Y19 Y1A Y1B Y1C Y1D Y1E Y1F COM- CTL+

X0 X1 X2 X3 X4 X5 X6 X7 COM NC Y10 Y11 Y12 Y13 Y14 Y15 Y16 Y17 COM- CTL+
B RATE
40 20 10 8 4 2 1 4 2 1
1.5ms or less 10.2 to 26.4VDC
ON→OFF External Voltage
(at 24VDC) (ripple ratio: within 5%)

STATION NO.
power
16 points/common 30mA or lower
supply for
Wiring method for common (1-wire, FCN connector Current (at 24VDC and all points ON),
output part
type) excluding external load current

Y10-Y1F
X0-XF
Positive/negative Wiring method for 16 points/common
Input type common shared type common (1-wire, FCN connector type)

Y10 11 1213 14151617 Y18191A1B1C1D1E1F

X8 9 A B C D E F
(sink/source shared type) Surge suppressor Zener diode

A J65SBTCF1-32DT
Number of occupied stations 32-point assignment/station (32 points used)
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
Module power supply
Current 50mA or lower (at 24VDC and all points ON)
X0 1 2 3 4 5 6 7

Noise voltage 500Vp-p, noise width 1µs,

Noise immunity
(FG)
24G

noise frequency 25 to 60Hz (DC type noise simulator condition)

Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
DA DG +24V
SLD

10MΩ or higher between all DC external terminals and ground (500VDC insulation
Insulation resistance
resistance tester)
DB

Protection degree IP2X

Weight 0.15kg
External 7-point two-piece terminal block
connection Communication part, [Transmission circuit, module power supply, FG]
system module power supply part M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m)
Applicable solderless terminal: 2 or less
I/O power supply part, 40-pin connector [I/O power supply, I/O signal]
I/O part (A6CON1, A6CON2, A6CON3, A6CON4)
Module mounting screw M4 screw with plain washer finished round
(tightening torque range: 0.78 to 1.08N•m)
Mountable with a DIN rail in 6 orientations
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable Communication y RAV1.25-3 (compliant with JIS C 2805)
Applicable 2
wire size part, [Applicable wire size: 0.3 to 1.25mm ]
solderless
module power y V2-MS3, RAP2-3SL, TGV2-3N
terminal 2
supply part [Applicable wire size: 1.25 to 2.0mm ]
2
I/O power supply part, 0.3mm (AWG22) or less (A6CON1 and A6CON4)
2
I/O part 0.2 to 0.08mm (AWG28 to 24) (A6CON2)
2
0.08mm (AWG28) stranded wire, φ0.25mm (AWG30) single wire
(A6CON3)
Accessory User’s manual

6 - 73 6 - 73
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection
Pin layout Terminal number Signal name
TB1 DA
1 DA TB2 DB
2 DB TB3 DG
3 DG TB4 SLD
Insulation
4 SLD
TB5 +24 V
5 +24V
6 FG TB6 (FG)
7 24G TB7 24G
Module power supply
Pin Signal Pin Signal
B20 X0 number name number name
B19 X1
B20 X0 A20 X8
B18 X2
B17 X3 B19 X1 A19 X9
B16 X4 B18 X2 A18 XA
B15 X5 B17 X3 A17 XB
B14 X6 B16 X4 A16 XC
B13 X7
B15 X5 A15 XD
A20 X8
A19 X9 B14 X6 A14 XE
A18 XA B13 X7 A13 XF
A17 XB B12 COM A12 COM
A16 XC
B11 Empty A11 Empty
A15 XD
XE B10 Y10 A10 Y18
A14
A13 XF B9 Y11 A9 Y19
A,B12 COM B8 Y12 A8 Y1A
A,B11 Empty B7 Y13 A7 Y1B
B10 Y10
Load B6 Y14 A6 Y1C
B9 Y11
B8 Y12 B5 Y15 A5 Y1D
B7 Y13 B4 Y16 A4 Y1E
B6 Y14 B3 Y17 A3 Y1F
B5 Y15
B2 COM- A2 COM-
B4 Y16
B1 CTL+ A1 CTL+
B3 Y17
A10 Y18 Viewed from the
A9 Y19 front of the module
A8 Y1A
A7 Y1B
A6 Y1C
A5 Y1D
A4 Y1E
Load
A3 Y1F
A,B1 CTL+
External power supply
A,B2 COM-
for output part Constant-voltage circuit

Load power supply

Load
A3 Y1F External power supply for output part
A,B1 CTL+ and load power supply (common)
A,B2 COM-

6 - 74 6 - 74
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.5.2 AJ65VBTCF1-32DT1 combined module

Type DC input transistor output combined module

Item AJ65VBTCF1-32DT1 Appearance
Input Output
Number of input points 16 points Number of output points 16 points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 12/24VDC
Operating load voltage 10.2 to 26.4VDC
Rated input current Approx. 5mA
range (ripple ratio: within 5%)
19.2 to 26.4VDC
Operating voltage range Max. load current 0.1A/point, 1.6A/common
(ripple ratio: within 5%)
Max. number of simultaneous 100% or 60%
Max. inrush current 0.7A, 10ms or less
input points (Refer to Section 1.3.)
ON voltage/ON current 15VDC or higher/3mA or higher Leakage current at OFF 0.1mA or lower
OFF voltage/OFF current 3VDC or lower/0.5mA or lower 0.1VDC or lower (TYP.) 0.1A,
Max. voltage drop at ON
Input resistance Approx. 4.7kΩ 0.2VDC or lower (MAX.) 0.1A
Response time Output type Sink type
OFF→ON 0.2ms or less (at 24VDC)
Overload protection, overvoltage
Protection function
ON→OFF 0.2ms or less (at 24VDC) protection, overheat protection
OFF→ON 1ms or less
16 points/common Response
Wiring method for common 1ms or less
(1-wire, FCN connector type) time ON→OFF
(rated load, resistive load)
AJ65VBTCF1-32DT1
10.2 to 26.4VDC
External Voltage
(ripple ratio: within 5%)
power LINK X0 Y10
10mA or lower
supply for CON.A CON.B XF Y1F
Current (at 24VDC and all points ON),
output part PW
excluding external load current L RUN

Positive/negative common Wiring method for 16 points/common L ERR

Input type shared type common (1-wire, FCN connector type) 0

1
(sink/source shared type) Surge suppressor Zener diode 2
3
Number of occupied stations 32-point assignment/station (32 points used) 4
5
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%) 6
7
supply Current 50mA or lower (at 24VDC and all points ON) 8
Noise voltage 500Vp-p, noise width 1µs, 9
Noise immunity A
noise frequency 25 to 60Hz (DC type noise simulator condition) PW/AUX. B
C
CON.C CON.D
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground D
E
10MΩ or higher between all DC external terminals and ground (500VDC insulation resistance F
Insulation resistance
tester)
Protection degree IP1XB
Weight 0.16kg
External One-touch connector for communication [Transmission circuit]
connection 5-pin IDC plug is sold separately.
Communication part
system <Optional>
Online connector for communication: A6CON-LJ5P
One-touch connector for power supply and FG [Module power supply, FG]
5-pin IDC plug is sold separately: A6CON-PW5P, A6CON-PW5P-SOD
Power supply part
<Optional>
Online connector for power supply: A6CON-PWJ5P
I/O part Connector for I/O (40 pins, M3 screw)
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Applicable Connector for Applicable cable:
wire size communication FANC-110SBH, FA-CBL200PSBH, CS-110
0.66 to 0.98mm2 (AWG18)
Connector for power [φ2.2 to 3.0mm (A6CON-PW5P), φ2.0 to 2.3mm (A6CON-PW5P-SOD)]
supply and FG Wire diameter: 0.16mm or more
Insulating coating material: PVC (heat-resistant)
Connector for I/O 0.3mm2 (AWG22)
A6CON1 (soldering type), A6CON2 (crimping type), A6CON3 (IDC type),
Applicable connector for I/O
A6CON4 (soldering type)
Accessory User’s manual

6 - 75 6 - 75
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection

Pin layout

CON A CON B CON 1

CON A 1
1
LINK CABLE 2
1 DA 2 B20 A20
(IN) 3
2 DB 3 B19 A19

4
3 DG 4 B18
B17
A18
A17
5
4 Empty 5 B16 A16
5 SLD B15 A15
B14 A14
CON B B13 A13
1 B12 A12
1 DA B11 A11
LINK CABLE 2
2 DB B10 A10
(OUT) 3 B9 A9
3 DG
4 B8 A8
4 Empty B7 A7
5 B6 A6
5 SLD
B5 A5
One-touch connector for communication B4 A4
B3 A3
B2 A2
CON C CON CCON D B1 A1
1 Insulation
UNIT POWER CABLE(IN) 1 FG 1
2
3
2 +24V(UNIT) 2
4
3 24G(UNIT) 3
5
4 Empty 4
5 Empty 5
CON D
1
UNIT POWER CABLE(OUT) 1 FG
2 Viewed from the front
2 +24V(UNIT)
3
4
3 24G(UNIT) of the module
4 Empty
5
5 Empty

1 Pin Pin Signal

One-touch connector for power supply and FG Signal name
CON 1 number number name
B20, A20 1 DA
2 DB
CON
3 DG
A, B
4 Empty
B13, A13 5 SLD
20 X0 20 X8
B12, A12
19 X1 19 X9
18 X2 18 XA
CON1 17 X3 17 XB
Load B10, A10 16 X4 16 XC
15 X5 15 XD
14 X6 14 XE
13 X7 13 XF
12 COM 12 COM
Load B3, A3
CON 11 Empty CON 11 Empty
B1, A1 1-B 10 Y10 1-A 10 Y18
External power supply 9 Y11 9 Y19
for output part B2, A2
8 Y12 8 Y1A
7 Y13 7 Y1B
Load power supply
6 Y14 6 Y1C
Constant-voltage circuit
5 Y15 5 Y1D
Load B3, A3
4 Y16 4 Y1E
B1, A1 External power supply for output part
and load power supply (common) 3 Y17 3 Y1F
B2, A2
2 COM- 2 COM-
1 CTL+ 1 CTL+
1 (FG)
2 +24V(UNIT)
CON
3 24G(UNIT)
C-D
4 Empty
1:Attach an unwired connector plug to an unused one-touch connector for power supply and FG. 5 Empty

6 - 76 6 - 76
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection

<When using online connectors>

Online connector
for communication
CONA
1
1 DA
LINK CABLE 2
(IN) 2 DB
3
3 DG
4
4 Empty
5
5 SLD
CONB
1
1 DA
LINK CABLE 2
(OUT) 2 DB
3
3 DG
4
4 Empty
5
5 SLD
One-touch connector
for communication
CONC
1
UNIT POWER CABLE(IN) 1 FG
2
2 +24V(UNIT)
3
3 24G(UNIT)
4
4 Empty
5
5 Empty
COND
1
UNIT POWER CABLE(OUT) 1 FG
2
2 +24V(UNIT)
3
3 24G(UNIT)
4
4 Empty
5
5 Empty

One-touch connector for power

supply and FG *1 Online connector
for power supply
and FG

1:Attach an unwired connector plug to an unused one-touch connector for power supply and FG.

6 - 77 6 - 77
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.5.3 AJ65VBTCFJ1-32DT1 combined module

Type DC input transistor output combined module

Item AJ65VBTCFJ1-32DT1 Appearance
Input Output
Number of input points 16 points Number of output points 16 points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 24VDC
Operating load voltage Same as that for the module power
Rated input current Approx. 5mA
range supply
Same as that for the module
Operating voltage range Max. load current 0.1A/point, 1.6A/common
power supply
Max. number of simultaneous 100% or 40%
Max. inrush current 0.7A, 10ms or less
input points (Refer to Section 1.3.)
ON voltage/ON current 15VDC or higher/3mA or higher Leakage current at OFF 0.1mA or lower
OFF voltage/OFF current 3VDC or lower/0.5mA or lower 0.1VDC or lower (TYP.) 0.1A,
Max. voltage drop at ON
Input resistance Approx. 4.7kΩ 0.2VDC or lower (MAX.) 0.1A
Response time Output type Sink type
OFF→ON 0.2ms or less (at 24VDC)
Overload protection, overvoltage
Protection function
ON→OFF 0.2ms or less (at 24VDC) protection, overheat protection
OFF→ON 1ms or less
Response
Input type Positive common (sink type) 1ms or less
time ON→OFF
(rated load, resistive load)
External power supply Same as that for the module power
for output part supply
Surge suppressor Zener diode
Wiring method for common 32 points/common (1-wire, FCN connector type)
Number of occupied stations 32-point assignment/station (32 points used)
Module power Voltage 20.4 to 28.8VDC (ripple ratio: within 5%)
supply Current 50mA or lower (at 24VDC and all points ON), excluding external load current
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity
noise frequency 25 to 60Hz (DC type noise simulator condition)
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
10MΩ or higher between all DC external terminals and ground (500VDC insulation resistance
Insulation resistance
tester)
Protection degree IP1XB
Weight 0.16kg
One-touch connector for communication [Transmission circuit]
5-pin IDC plug is sold separately: A6CON-L5P
Communication part
<Optional>
External Online connector for communication: A6CON-LJ5P
connection One-touch connector for power supply and FG [Module power supply, FG]
system 5-pin IDC plug is sold separately: A6CON-PW5P, A6CON-PW5P-SOD
Power supply part
<Optional>
Online connector for power supply: A6CON-PWJ5P
I/O part Connector for I/O (40 pins, M3 screw)
Applicable DIN rail TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Connector for Applicable cable:
communication FANC-110SBH, FA-CBL200PSBH, CS-110
0.66 to 0.98mm2 (AWG18)
Applicable
Connector for power [φ2.2 to 3.0mm (A6CON-PW5P), φ2.0 to 2.3mm (A6CON-PW5P-SOD)]
wire size
supply and FG Wire diameter: 0.16mm or more
Insulating coating material: PVC (heat-resistant)
2
Connector for I/O 0.3mm (AWG22)
A6CON1 (soldering type), A6CON2 (crimping type), A6CON3 (IDC type),
Applicable connector for I/O
A6CON4 (soldering type)
Accessory User’s manual

6 - 78 6 - 78
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection

Pin layout
CON A
1
1 DA CON A CON B CON E
LINK CABLE 2
2 DB 1
(IN) 3 2
3 DG B20 A20
4 3 B19 A19
4 Empty 4 B18 A18
5 5
B17 A17
5 SLD B16 A16
B15 A15
B14 A14
CON B B13 A13
1 B12 A12
1 DA B11 A11
LINK CABLE 2
2 DB
B10
B9
A10
A9
(OUT) 3 B8 A8
3 DG B7
B6
A7
A6
4
4 Empty B5
B4
A5
A4
5 B3 A3
5 SLD CON C CON D B2 A2
B1 A1
One-touch connector for 1
communication 2
3
CON C Insulation 4
1 5
UNIT POWER CABLE(IN) 1 FG
2
2 +24V(UNIT,I/O)
3
3 24G(UNIT,I/O) Viewed from the front of the module
4
4 Empty
5
5 Empty
CON D Pin Pin Signal
1 Signal name
UNIT POWER CABLE(OUT) 1 FG number number name
2
2 +24V(UNIT,I/O)
3 1 DA
3 24G(UNIT,I/O)
4 2 DB
4 Empty
5
Empty
CON
5 3 DG
One-touch connector for A, B
4 Empty
power supply and FG 1
2
CON E 5 SLD
B20, A20 20 X0 20 X8
19 X1 19 X9
18 X2 18 XA
17 X3 17 XB
B13, A13 16 X4 16 XC
15 X5 15 XD
COM- B12, A12 14 X6 14 XE
13 X7 13 XF
12 COM- 12 COM-
Load B10, A10 CON 11 Empty CON 11 Empty
E-B 10 Y10 E-A 10 Y18
9 Y11 9 Y19
8 Y12 8 Y1A
7 Y13 7 Y1B
Load B3, A3 6 Y14 6 Y1C
5 Y15 5 Y1D
4 Y16 4 Y1E
3 Y17 3 Y1F
COM+ B1, A1 2 Empty 2 Empty
1 COM+ 1 COM+
1 (FG)
Constant-voltage circuit +24V
2
(UNIT, I/O)
CON
24G
C-D 3
(UNIT, I/O)

1: Attach an unwired connector plug to an unused one-touch connector for power supply and FG. 4 Empty
2: Do not supply power to the CON E. 5 Empty

6 - 79 6 - 79
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection

<When using online connectors>

Online connector
for communication
CON.A
1
1 DA
LINK CABLE 2
(IN) 2 DB
3
3 DG
4
4 Empty
5
5 SLD
CON.B
1
1 DA
LINK CABLE 2
(OUT) 2 DB
3
3 DG
4
4 Empty
5
5 SLD
One-touch connector
for communication
CON.C
1
UNIT POWER CABLE(IN) 1 FG
2
2 +24V(UNIT,I/O)
3 24G(UNIT,I/O)
3
4
4 Empty
5
5 Empty
I/O POWER CABLE(IN) CON.D
1
1 FG
2
UNIT POWER 2 +24V(UNIT,I/O)
CABLE(OUT) 3 24G(UNIT,I/O)
3
4
I/O POWER 4 Empty
5
CABLE(OUT) 5 Empty

One-touch connector for power

supply and FG *1 Online connector
for power supply
and FG

1:Attach an unwired connector plug to an unused one-touch connector for power supply and FG.

6 - 80 6 - 80
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.6 Waterproof Type Combined Module

6.6.1 AJ65FBTA42-16DT combined module

Type DC input transistor output combined module

Item AJ65FBTA42-16DT Appearance
Input Output
Number of input points 8 points Number of output points 8 points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 24VDC
Operating load voltage 20.4 to 26.4VDC
Rated input current Approx. 7mA
range (ripple ratio: within 5%)
20.4 to 26.4VDC
Operating voltage range Max. load current 0.5A/point, 2.4A/common
(ripple ratio: within 5%)
Max. number of simultaneous
100% Max. inrush current 1.0A, 10ms or less
input points
14VDC or higher/
ON voltage/ON current Leakage current at OFF 0.25mA or lower
3.5mA or higher
0.15VDC or lower (TYP.) 0.5A,
OFF voltage/OFF current 6VDC or lower/1.7mA or lower Max. voltage drop at ON
0.25VDC or lower (MAX.) 0.5A AJ65FBTA42-16DT

Input resistance Approx. 3.3kΩ Output type Sink type

Response time OFF→ON 1.5ms or less (at 24VDC) Overload protection, overheat Y8
Y9
Protection function YA
YB
ON→OFF 1.5ms or less (at 24VDC) protection YC
YD
YE
YF
Response OFF→ON 0.5ms or less
time ON→OFF 1.5ms or less (resistive load)
20.4 to 26.4VDC
External Voltage
(ripple ratio: within 5%)
power
10mA or lower Y
supply for Y
Current (at 24VDC and all points ON),
output part
excluding external load current
Input type Positive common (sink type) Surge suppressor Zener diode Y
Y
Supply current for connected
1.0A or lower/common
device
Wiring method for common 16 points/common (2- to 4-wire, waterproof connector type) Y
Y
Number of occupied stations 32-point assignment/station (16 points used)
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
Y
supply Current 50mA or lower (at 24VDC and all points ON) Y

Noise voltage 500Vp-p, noise width 1µs,

Noise immunity
noise frequency 25 to 60Hz (DC type noise simulator condition)
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
10MΩ or higher between all DC external terminals and ground (500VDC insulation resistance
Insulation resistance
tester)
Protection degree IP67
Weight 0.40kg
Accessory User’s manual
Optional item Waterproof cap: A6CAP-WP2 (20 pieces)
Other connecting devices Refer to Section 1.6.1.

6 - 81 6 - 81
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection
Pin layout Connector for communication
Pin
LINK IN LINK OUT
number
1 SLD SLD
2 DB DB
LINK IN 3 DG DG
4
2 4 DA DA
3
1 Communication 5 No pins Empty
circuit Connector for power supply
110
130 Pin
LINK OUT
4 LINK IN UNIT POWER AUX.
number
2
Male
3 Terminating resistor 1 +24V(UNIT) +24V(I/O)
2 1
1 setting switch
5
3 4 2 Empty Empty
3 24G(UNIT) 24G(I/O)
LINK OUT 4 Empty Empty
Insulation 5 FG FG
UNIT POWER Female
1 1 2
3 4 5
3
Connector for I/O
5 Pin Signal Pin Signal
2
4 number name number name
Module mounting screw (FG) UNIT POWER/AUX.
1 +24V 1 +24V
Male
2 1 2 X1 2 Y9
AUX.
1 3
5
4 X0 Y8
X1 3 24G Y9 3 Empty
3
5 4 X0 4 Y8
2 Connector for I/O 5 Empty 5 Empty
4
Constant-voltage circuit Female 1 +24V 1 +24V
Connector for I/O 1 2
5
4-wire sensor
4 3 2 X3 2 YB
X2 YA
(sink output) 3 24G 3 Empty
Black 4 X3 YB
Detection
circuit White 2 4 X2 4 YA
Brown 1
Blue 3 Viewed from the front
5 Empty 5 Empty
5 of the module 1 +24V 1 +24V
3-wire sensor 2 X5 2 YD
(sink output) X4 YC
Black 4 X5 3 24G YD 3 Empty
Detection
2
circuit
Brown 1
4 X4 4 YC
Blue 3 5 Empty 5 Empty
5
1 +24V 1 +24V
2-wire sensor 2 X7 2 YF
(sink output) Brown 4
X6 YE
X7 3 24G YF 3 Empty
Detection 2
circuit 1 4 X6 4 YE
Blue 3
5 Empty 5 Empty
5

Load
4
Load 2
1
3
5

6 - 82 6 - 82
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.6.2 AJ65FBTA42-16DTE combined module

Type DC input transistor output combined module

Item AJ65FBTA42-16DTE Appearance
Input Output
Number of input points 8 points Number of output points 8 points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 24VDC
Operating load voltage 20.4 to 26.4VDC
Rated input current Approx. 7mA
range (ripple ratio: within 5%)
20.4 to 26.4VDC
Operating voltage range Max. load current 1.0A/point, 4A/common
(ripple ratio: within 5%)
Max. number of simultaneous
100% Max. inrush current 2.0A, 10ms or less
input points
14VDC or higher/
ON voltage/ON current Leakage current at OFF 0.3mA or lower
3.5mA or higher
OFF voltage/OFF current 6VDC or lower/1.7mA or lower 0.15VDC or lower (TYP.) 1.0A,
Max. voltage drop at ON
Input resistance Approx. 3.3kΩ 0.2VDC or lower (MAX.) 1.0A
OFF→ON 1.5ms or less (at 24VDC) Response OFF→ON 0.5ms or less
Response time AJ65FBTA42-16DTE
ON→OFF 1.5ms or less (at 24VDC) time ON→OFF 1.5ms or less (resistive load)
Output type Source type PROTECT
Y8
Y9
YA
Overload protection, overheat YB
YC
YD

protection YE
YF

Protection function
(The LED turns on when any
protection is activated.)
20.4 to 26.4VDC
External Voltage
(ripple ratio: within 5%)
power Y
15mA or lower Y
supply for
Current (at 24VDC and all points ON),
output part
excluding external load current
Y
Input type Negative common (source type) Surge suppressor Zener diode Y

Supply current for connected

1.0A or lower/common
device
Y

16 points/common Y

Wiring method for common

(input: 2- to 4-wire waterproof connector type, output: 2-wire waterproof connector type)
Number of occupied stations 32-point assignment/station (16 points used) Y
Y
Module power Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
supply Current 45mA or lower (at 24VDC and all points ON)
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity
noise frequency 25 to 60Hz (DC type noise simulator condition)
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground
10MΩ or higher between all DC external terminals and ground (500VDC insulation resistance
Insulation resistance
tester)
Protection degree IP67
Weight 0.40kg
Accessory User’s manual
Optional item Waterproof cap: A6CAP-WP2 (20 pieces)
Other connecting devices Refer to Section 1.6.1.

6 - 83 6 - 83
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection
Pin layout Connector for communication
Pin
LINK IN LINK OUT
number
1 SLD SLD
2 DB DB
3 DG DG
LINK IN 4
2
4 DA DA
3 5 No pins Empty
1 Communication
circuit Connector for power supply
110
Pin
130 UNIT POWER AUX.
LINK OUT 4 number
2 LINK IN 1 +24V(UNIT) +24V(I/O)
3 Terminating resistor Male
1 setting switch 2 Empty Empty
2 1
5 3 4 3 24G(UNIT) 24G(I/O)
4 Empty Empty
Insulation LINK OUT 5 FG FG
UNIT POWER 1 Female Connector for I/O
3 1
5
2
5
4 3 Pin Signal Pin Signal
2 number name number name
4
Module mounting UNIT POWER/AUX. 1 +24V 1 Empty
screw (FG)
Male 2 X1 2 Y9
2 1 X0 Y8
AUX. 1 3
5
4 X1 3 24G Y9 3 24G
3 4 X0 4 Y8
5
2 Connector for I/O 5 Empty 5 Empty
4 1 +24V 1 Empty
Female
1 2
Connector for I/O
Constant-
4 5
3 2 X3 2 YB
4-wire sensor voltage circuit X2 YA
X3 3 24G YB 3 24G
(souce output)
4
Detection
Black
4 X2 4 YA
circuit White 2
Brown 1 Viewed from the front 5 Empty 5 Empty
Blue 3 of the module
5 1 +24V 1 Empty
2 X5 2 YD
3-wire sensor X4 YC
(souce output) X5 3 24G YD 3 24G
Black 4
Detection
2 4 X4 4 YC
circuit
Brown 1 5 Empty 5 Empty
Blue 3
5 1 +24V 1 Empty
2 X7 2 YF
2-wire sensor X6 YE
(souce output) 4 X7 3 24G YF 3 24G
Brown

Detection
2 4 X6 4 YE
circuit Blue 1
3 5 Empty 5 Empty
5

Load 4
Load 2
1
3
5

6 - 84 6 - 84
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

6.6.3 AJ65SBTW4-16DT combined module

Type DC input transistor output combined module

Item AJ65SBTW4-16DT Appearance
Input Output
Number of input points 8 points Number of output points 8 points
Isolation method Photocoupler Isolation method Photocoupler
Rated input voltage 24VDC Rated load voltage 24VDC
Operating load voltage 20.4 to 26.4VDC
Rated input current Approx. 5mA
range (ripple ratio: within 5%)
20.4 to 26.4VDC
Operating voltage range Max. load current 0.5A/point, 2.4A/common
(ripple ratio: within 5%)
Max. number of simultaneous input
100% Max. inrush current 1.0A, 10ms or less
points
14VDC or higher/
ON voltage/ON current Leakage current at OFF 0.25mA or lower
3.5mA or higher
6VDC or lower/ 0.3VDC or lower (TYP.) 0.5A,
OFF voltage/OFF current Max. voltage drop at ON
1mA or lower 0.6VDC or lower (MAX.) 0.5A
Input resistance Approx. 4.7kΩ Output type Sink type

OFF→ON 1.5ms or less (at 24VDC) Overload protection, overvoltage

Response time Protection function
protection, overheat protection
ON→OFF 1.5ms or less (at 24VDC)
Response OFF→ON 0.5ms or less

AJ65SBTW4-16DT
time

L ERR.
ON→OFF 1.5ms or less (resistive load)

L RUN

YC
YD
YA
YB

YE
YF
Y8
Y9

STATION NO.
20.4 to 26.4VDC
External Voltage
(ripple ratio: within 5%)

PW

X0
X1
X2
X3
X4
X5
X6
X7
power

MITSUBISHI
13mA or lower
supply for
Current (at 24VDC and all points ON),
output part

CON7

CON8
excluding external load current
Input type Positive common (sink type) Surge suppressor Zener diode
16 points/common (4-wire, waterproof connector type)
Wiring method for common
Same as that for the module power supply

CON5

CON6
Number of occupied stations 32-point assignment/station (16 points used)
Voltage 20.4 to 26.4VDC (ripple ratio: within 5%)
Module power supply
Current 50mA or lower (at 24VDC and all points ON)

CON3

CON4
Noise voltage 500Vp-p, noise width 1µs,
Noise immunity
noise frequency 25 to 60Hz (DC type noise simulator condition)
Withstand voltage 500VAC for 1 minute between all DC external terminals and ground CON1

CON2
10MΩ or higher between all DC external terminals and ground (500VDC insulation
Insulation resistance
resistance tester)
POWER CABL

POWER CABL

Protection degree IP67

Weight 0.70kg
OUT
IN

7-point two-piece terminal block [Transmission circuit, module power supply, FG]
LINK CABL

LINK CABL

M3×5.2 screw (tightening torque range: 0.59 to 0.88N•m),

Waterproof connector
External connection system
[compliant with IEC 60947-5-2, M12, male, 4 pins, IP67] (connector for I/O part)
<Optional>
Dustproof cap: A6CAP-DC1 (20 pieces), waterproof cap: A6CAP-WP1 (20 pieces)
Applicable cable size: φ5.0 to 8.0 mm
y RAV1.25-3 (compliant with JIS C 2805)
Transmission circuit, 2
Applicable [Applicable wire size: 0.3 to 1.25mm ]
module power supply part
wire size y V2-MS3, RAP2-3SL, TGV2-3N
[Applicable wire size: 1.25 to 2.0mm2]
Connector for I/O ─
Module top-cover
0.54 to 0.64N•m
mounting screw (M3)
Module front-cover
Tightening 0.54 to 0.64N•m
mounting screw (M3)
torque
Module mounting screw
range
(M4 with plain washer 1.27 to 1.47N•m
finished round)
Nut for pipe 0.99 to 1.48N•m
Through pipe specifications Applicable cable size: φ5.0 to 8.0 mm
Accessory User’s manual, Waterproof plug (2 pieces)

6 - 85 6 - 85
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection
Terminal Signal
<Connection example of 4-, 3-, and 2-wire sensors>
number name
TB1 DA
TB2 DB
LINK CABLE TB3 DG
1 DA TB4 SLD
2 DB
TB5 +24V
3 DG
Insulation TB6 (FG)
4 SLD
5 +24V TB7 24G
6 FG
Pin Signal
7 24G
Constant- number name
Module power supply and POWER CABLE voltage circuit
external power supply (common) 1 +24V
2 Y8
CON1
Module 3 24G
mounting 4 X0
screw
1 +24V
4-wire sensor 2 Y9
(sink output/ CON1 CON2
Black 4 3 24G
sink input) Detection
circuit White 2
4 X1
Brown 1
Blue 3 1 +24V
2 YA
CON3
3 24G
4 X2
1 +24V
2 YB
3-wire sensor CON2 CON4
3 24G
(sink output) Black 4
Detection 4 X3
circuit 2
Brown 1 1 +24V
Blue 3 2 YC
CON5
3 24G
4 X4
1 +24V
2 YD
CON6
3 24G
4 X5
2-wire sensor CON8
1 +24V
(sink output) Brown 4
Detection 2 2 YE
circuit CON7
1 3 24G
Blue 3
4 X6
1 +24V
2 YF
CON8
3 24G
4 X7

6 - 86 6 - 86
6 SPECIFICATIONS FOR COMBINED MODULES
MELSEC-A

External connection

<Connection example of other I/O devices>

LINK CABLE
1 DA
2 DB
3 DG Insulation
4 SLD
5 +24V
6 FG
7 24G Constant-
Module power supply and POWER CABLE voltage circuit
external power supply (common)

Module
mounting
screw

CON1
4
2
1
3

CON8
4
Load 2
1
3

Pin layout

Viewed from the front of the module

6 - 87 6 - 87
 7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

7 HANDLING OF COMPACT REMOTE I/O MODULES

7.1 Handling and Installation Precautions
This section lists the precautions for handling and installing the compact remote I/O
module for the CC-Link system.

• Do not touch any terminal or connector while power is on.

WARNING Doing so will cause electric shock.

• Prevent foreign matter such as dust or wire chips from entering the module.
CAUTION Such foreign matter can cause a fire, failure, or malfunction.
• Do not disassemble or modify the module.
Doing so may cause failure, malfunction, injury, or a fire.
• Do not directly touch any conductive part of the module.
Doing so can cause malfunction or failure of the module.
• Do not drop or apply any strong shock to the module. Doing so may damage the
module.
• Use applicable solderless terminals and tighten them within the specified torque
range. If any spade solderless terminal is used, it may be disconnected when the
terminal screw comes loose, resulting in failure.
• Tighten the terminal screw within the specified torque range.
Undertightening can cause fire or malfunction.
Overtightening can damage the screw, resulting in short circuit or malfunction.
• When disposing of this product, treat it as industrial waste.
• Use the module in an environment that meets the general specifications in this
manual.
Failure to do so may result in electric shock, fire, malfunction, or damage to or
deterioration of the product.
• Securely fix the module with a DIN rail or mounting screws. Tighten the screws
within the specified torque range.
Undertightening can cause drop of the screw, short circuit or malfunction.
7 Overtightening can damage the screw, resulting in drop or short circuit.
• Shut off the external power supply (all phases) used in the system before mounting
or removing a module to/from a control panel.
Failure to do so may cause the module to fail or malfunction.

(1) Tighten the module mounting screw or terminal block screw within the following
torque range. Overtightening can damage the module case.
(a) Terminal block type, one-touch connector type, or FCN connector type
Screw Tightening torque range
Module mounting screw (M4 screw with plain washer finished round) 0.78 to 1.08N·m
Terminal block screw (M3) 0.59 to 0.88N·m
Terminal block installation screw (M3.5) 0.68 to 0.98N·m

(b) Waterproof type (AJ65SBTW -16 )

Screw Tightening torque range
Module top cover mounting screw (M3) 0.54 to 0.64N·m
Module front cover mounting screw (M3) 0.54 to 0.64N·m
Nut for pipe 0.99 to 1.48N·m
Module mounting screw (M4 screw with plain washer finished round) 1.27 to 1.47N·m
Terminal block screw (M3) 0.59 to 0.88N·m
Terminal block installation screw (M3.5) 0.68 to 0.98N·m

7-1 7-1
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

(c) Low profile waterproof type (AJ65FBTA -16 )

Screw Tightening torque range
Communication adapter mounting screw (M4) 0.42 to 0.58N·m
Module mounting screw (M4) 0.78 to 1.18N·m
Waterproof cap (A6CAP-WP2) 0.29 to 0.34N·m

(d) Spring clamp terminal block type or sensor connector (e-CON) type
Screw Tightening torque range
Mounting bracket (M4) 0.82 to 1.11N·m

POINT
• For a terminal and a screw, avoid adhering to oil.
Doing so may damage the screw.
• When using two solderless terminals, place them with their backs faced.
If not, a screw cannot be full inserted, resulting in damage to the screw.
• Tighten the terminal screw with an applicable driver.
Failure to do so may damage the screw.

(2) A scratch-resistant film is attached on the surface of the module during

transportation.
Remove the film before operation.

7-2 7-2
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

(3) Observe the following points when installing a module to a control panel using a
DIN rail.
(a) Applicable DIN rail (compliant with IEC 60715)
TH35-7.5Fe
TH35-7.5Al
(b) Mounting pitch
When installing a DIN rail to a control panel, keep mounting pitches 200mm
(7.87 inches) or less.
(c) Area where screws cannot used for Din rail installation
When installing the AJ65VBTCE -16 and AJ65VBTCE -32 to the DIN
rail horizontally as shown below, tighten a screw so that a certain distance will
be ensured between the screw and the DIN rail hook on the right side of
module.
Failure to do so may cause the screw to interfere with the DIN rail hook.
1) For AJ65VBTCE -16
Tighten a screw keeping a distance of 50mm (1.97 inches) or more from
the DIN rail hook on the right side of module.
DIN rail hook
3M 35610 B

3M 35610 A

50mm (1.97 inches)

1
1

7-3 7-3
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

2) For AJ65VBTCE -32

Tighten a screw keeping a distance of 80mm (3.15 inches) or more from
the DIN rail hook on the right side of module.
DIN rail hook

3M 35610 B

3M 35610 A
1
80mm (3.15 inches)
1

(4) When mounting the compact remote I/O module to a DIN rail, push in the DIN rail
hook located at the bottom of the module until it clicks.
For AJ65SBTB1-8 , AJ65SBTB1-16 , For AJ65SBTB1B-16 , AJ65SBTB1-32 ,
AJ65SBTC4-16 , AJ65SBTC1-32 , AJ65SBTB2-16 , AJ65SBTB2N-16 ,
AJ65SBTCF1-32 , AJ65SBTB2-8 , AJ65SBTB3-16 , AJ65SBTB32-16 ,
AJ65SBTB2N-8 , AJ65SBTB32-8 , AJ65VBTS -32 , AJ65VBTCE -32
AJ65VBTS -16 , AJ65VBTCE -8 , compact remote I/O modules
AJ65VBTCE -16
compact remote I/O modules

DIN rail
DIN rail DIN rail hook
DIN rail hook

Note: Do not touch the board

as described below.
It may result in failure.

Board

DIN rail

7-4 7-4
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

(5) When mounting the compact remote I/O module on the DIN rail, put its upper
hook onto the fixing bracket and push the module until it clicks.

Click

[Mounting dimensions]
(a) A6PLT-J65V1 (For module width 41mm only) (b) A6PLT-J65V2 (For module width 60mm only)
M4 screw 8mm M4 screw 8mm
long or more long or more
6 29 7.5 45

35
35

17.5
17.5

41 60 7.5

Unit : mm

(6) Do not install the compact remote I/O module to the place where:
(a) an ambient temperature is outside the range of 0 to 55°C (0 to 45°C for the
waterproof remote I/O module),
(b) ambient humidity is outside the range of 10 to 99%RH,
(c) condensation occurs due to a sudden temperature change,
(d) corrosive gas or combustible gas is present,
(e) conductive powder (such as dust and iron powder), oil mist, salinity, or
organic solvent is filled,
(f) the module is exposed to direct sunlight,
(g) a strong electric field or strong magnetic field is generated, and
(h) the module is subject to vibration or shock.

7-5 7-5
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

(7) When installing the compact remote I/O module into a panel, etc., provide 60mm
(2.36 inches) or more of space between the top and bottom of the module and
other structures or parts so that good ventilation and ease of operation when
exchanging modules can be secured.

(8) Install the compact remote I/O module on a level surface.

If the surface is uneven, unnecessary force is applied to the printed circuit board,
causing malfunction.

(9) When installing the waterproof-type remote I/O module, provide the space shown
in the figure below between the top and bottom of the module and other structures
or parts so that good ventilation can be secured and that interference and
application of load on the waterproof connector can be prevented.
When connecting two modules in parallel, secure 5mm (0.2 inches) of space
between them.

5 (0.20) or more

3 (0.12) or more

Installation
surface

80 (3.15) or more 1

3 (0.12) or more 3 (0.12) or more

1 Provide a space so that no load is applied to the cable

(the space differs depending on the waterproof connector used).

<When two modules are installed in parallel>

7 (0.28) or more

Unit : mm (inch)

7-6 7-6
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

(10) If a waterproof cap is being installed on the low profile waterproof type remote I/O
module, in order to improve ventilation and also to prevent interference, as well
as to prevent a load from bearing on the waterproof connector, all the distances
shown in the following figures between the module's side surfaces and the
structure or parts.

1 2
0 or more 0 or more

1 2
0
or more
1
0 or more

2
2 or more

1 If you disconnect and connect the communications adapter, set the operating
distance using a screwdriver, etc.
2 If you are using a right angle type waterproof plug or Y branch connector, set a
distance where no load will be brought to bear on the cable.

7-7 7-7
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

(11) When installing the sensor connector (e-CON) type modules in parallel, take
intervals between the modules as shown below.
(The interval is required for the size of a DIN rail hook or mounting brackets.)
*3
Installation method of the module Installation orientation of the module Interval
Basic, Upside down
5mm
*1 (vertical installation)
Using a DIN rail
Basic, Upside down
5mm
(horizontal installation)
Basic, Upside down
5mm
*2 (vertical installation)
Using screws
Basic, Upside down
15mm
(horizontal installation)
* 1 This is the case when a DIN rail is installed horizontally. Do not apply this interval
to the AJ65VBTCE -8 .
* 2 This is the case when mounting brackets are attached on the top and bottom
sides of the module. If the brackets are attached on the right and left sides of the
module, apply the intervals reversely. (The interval for the vertical installation is
15mm and the interval for the horizontal installation is 5mm.)
* 3 The interval indicates the distance from the modules that are installed on the
either side.

(12) When handling the DIP switch, observe the following:

(a) Use a compact driver.
Do not handle the DIP switch with a mechanical pencil or a sharp, such as a
pair of tweezers and a needle.
If the lead or lead powder of a mechanical pencil enters into the switch, a
failure may result. Or if it drops into a circuit board, an electrical problem may
result.
Using a sharp may damage the switch, resulting in failure.
(b) Slide the switch lever one by one horizontally to the intended direction.
If the switch is slid from an oblique direction or from the right above, it may
damage or be transformed due to a load.

Switch lever

Driver

7-8 7-8
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

7.2 Wiring Procedures for One-touch Connector Plugs

7.2.1 List of one-touch connector plugs

The following table lists one-touch connector plugs applicable to the CC-Link system
compact remote I/O module.
Specifications
Mitsubishi model Part model name Applicable Maximum Color of the
Product name
name (manufacturer) Applicable cable size (core) cable size rated cover
(diameter) current
One-touch 33104-6000FL φ1.0 to
A6CON-P214 2 Transparent
connector plug 5 0.14 to 0.2mm 1.4mm
2A
1, 4 33104-6100FL (AWG26 to 24) φ1.4 to
A6CON-P220 Yellow
5 2.0mm
33104-6200FL φ1.0 to
A6CON-P514 2 Red
5 0.3 to 0.5mm 1.4mm
3A
33104-6300FL (AWG22 to 20) φ1.4 to
A6CON-P520 Blue
5 2.0mm
2
One-touch communication 0.5mm φ2.2 to
connector plug line (AWG20) 3.0mm
35505-6000-
for A6CON-L5P 2
Red
B0M GF 5 0.5mm
communication shielded cable
(AWG20)
2, 4
One-touch 2
0.75mm (0.66 to 0.98mm )
2
35505-6080-A00 φ2.2 to
connector plug A6CON-PW5P (AWG18) wire diameter Gray
GF 5 3.0mm
for power 0.16mm or more
supply and FG 7A
Outer insulation layer
2, 4, 6 A6CON-PW5P- 35505-6180-A00 material PVC φ2.0 to
Blue
SOD GF 5 (Heat-resistant vinyl) 2.3mm

Online
connector for 35720-L200-B00
A6CON-LJ5P — — — — —
communication AK 5
3
Online
connector for 35720-L200-A00
A6CON-PWJ5P — — — — —
power supply AK 5
and FG 3

1 A pack of A6CON-P (manufactured by Mitsubishi) includes 20 pieces.

2 A pack of A6CON- 5P (manufactured by Mitsubishi) includes 10 pieces.
3 A pack of A6CON- J5P (manufactured by Mitsubishi) includes 5 pieces.
4 One-touch connector plugs can no longer be used once crimped.
5 Manufactured by Sumitomo 3M Limited.
6 Check the outside diameter of an applicable cable and select a connector.

7-9 7-9
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

7.2.2 Precautions for transition wiring of one-touch connector for power supply and FG

Current flows in the modules when they are transition wired through one-touch
connectors for power supply and FG. Design the system so that the current flows in
each module equals to or lower than the maximum rated current shown below.
Input module Output module
(Example:AJ65VBTCE32-16DT) (Example:AJ65VBTCE2-16T)
CONA CONA
1 1
1 DA 1 DA
LINK CABLE LINK CABLE 2
2 2 DB
2 DB (IN) 3
(IN) 3 3 DG
3 DG 4
4 4 Empty
4 Empty 5
5 5 SLD
5 SLD
CONB CONB
1 1
1 DA 1 DA
LINK CABLE LINK CABLE 2
2 2 DB
2 DB (OUT) 3
(OUT) 3 3 DG
3 DG 4
4 4 Empty
4 Empty
One-touch connector 5 One-touch connector
5 5 SLD
5 SLD power supply and FG One-touch connector power supply and FG
One-touch connector for communication
for communication
CONC
CONC
3) UNIT POWER CABLE(IN)
1
1 FG
Insulation
1 Insulation 2
UNIT POWER CABLE(IN) 1 FG 2 +24V(UNIT)
2 3
1) 3
2
3
+24V(UNIT) 4
3
4
24G(UNIT)
+24V(I/O)
24G(UNIT) 5
4
2) 5
4
5
+24V(I/O)
I/O POWER CABLE(IN)
5 24G(I/O)
24G(I/O) COND
I/O POWER CABLE(IN) 1
COND UNIT POWER CABLE(OUT) 1 FG
8) UNIT POWER CABLE(OUT)
1
1 FG
2
3
2 +24V(UNIT)
2 3 24G(UNIT)
2 +24V(UNIT) 4
3 4 +24V(I/O)
3 24G(UNIT) 5
4 5 24G(I/O)
4 +24V(I/O) Connector for input signals
5 I/O POWER CABLE(OUT)
5 24G(I/O) (e-CON) Connector for output signals
I/O POWER CABLE(OUT) One-touch connector for
9) One-touch connector 7) power supply and FG
CON1 (e-CON)
for power supply and FG 1
CON1 Constant-
4) Brown 1
voltage circuit
2
3
Constant-
voltage circuit
3-wire type
2 Load 4
sensor
(sink output) Blue 3
Detection
circuit Black 4

5) 2 1

CON8
1 CON16
2 1
3 2
4 3
Load 4

6) CON9
1
2
3
Load 4

2 1

CON16
1
2
3
Load 4

Maximum rated
No. Power port Connector
current
1
1) Module power supply (IN) One-touch connector for power supply and FG (No.2 and 3 pins of CONC) 7A
1
2) I/O power supply (IN) One-touch connector for power supply and FG (No.4 and 5 pins of CONC) 7A

Maximum current
No. Power supply Power port (source) Description
consumption
3) Module power supply Module power supply (IN) Power supply for CC-Link modules Module power supply
4) Power supply for input Power supply for input devices connected, Supply current for
device such as sensors connected device
5) Input current Input signals from input devices Rated input current
6) External load power I/O power supply (IN) Power supply that is consumed by the load
Maximum load current
supply
7) External power supply Power supply for output circuits External power supply for
for output part output part current
8) Module power supply Power supply for the modules and external
Module power supply (IN) Depends on the modules
(OUT) devices connected by transition wiring
and external devices
9) I/O power supply (OUT) Power supply for the modules and external
I/O power supply (IN) connected
devices connected by transition wiring
1 The value of 1) equals to the sum of 3) and 8). The value of 2) equals to the sum of 4), 5), 6), 7), and 9). Design the system so that
each value of 1) and 2) equals to or lower than the maximum rated current (7A).

7 - 10 7 - 10
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

7.2.3 Wiring procedures for the one-touch connector

This section describes the wiring procedures for the one-touch connector of the one-
touch connector type or connector type compact remote I/O module.

Plug cover
Plug body
1) Check the connector.
Check that a plug cover is attached to the plug.

Note: Do not press the plug cover firmly into the plug before a
cable is inserted.
Metal contact Once crimped, the plug can no longer be used.

2) Insert a cable. ( 1)
ss Lift the end of the plug cover and insert a cable until it reaches
r le
mo
1m the other end of the cover (within 1mm from the other end).
Failure to do so may cause an improper crimping.

Note: When inserting the cable, prevent the cable from sticking
out from the plug cover end.
Metal contacts

3) Set the plug cover.

After the cable is inserted, put down the plug cover and set it to
the position where the metal contacts fit into the cover.

Metal contacts

4) Crimp the plug cover into the plug.

Pliers Hold the center of the plug cover with pliers and press it
vertically into the plug.

5) Press the latches into the plug.

Pliers After crimping, press the latches located at both ends of the
Latches plug cover into the plug.
Check that the cover is fixed to the plug with the latches.

(To the next page)

7 - 11 7 - 11
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

(From the previous page)

[Correct example] 6) Check that the plug cover is horizontally-embedded to the plug.
Check also that the cover is not floating.

Note: As shown in the wrong example on the left, if the cover is

not horizontally-embedded or the cover is floating, it may
result in improper crimping.
[Wrong example] Press the plug cover firmly into the plug with pliers. (Refer
to the correct example.)

[Correct example] 7) Check the crimped state from the top.

Check that there is no clearance between the plug and the
cover.

Note: As shown in the wrong example on the left, if the latch is

not securely engaged, clearance occurs between the plug
and the cover.
[Wrong example] Press the plug cover firmly into the plug with pliers. (Refer
to the correct example.)

Latches

Latch

Clearance

(Wiring completed)

1 When a cabtyre cable is used:

Strip the cable jacket 2cm or more.
If the wire lengths are not even, trim their ends with nippers to the same length.
2cm or more

Trim the wire ends to the same length

7 - 12 7 - 12
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

7.2.4 Wiring procedures for the one-touch connector for communication

This section describes the wiring procedures for the one-touch connector for
communication used for the connector type compact I/O module.

Plug cover 1) Check the connector.

Plug body
Check that a plug cover is attached to the plug.

Note: Do not press the plug cover firmly into the plug before a
cable is inserted.
Metal contact Once crimped, the plug can no longer be used.

2) Prepare a communication cable for connection.

Cut the shield wire, aluminum tape and braid. Strip the cable jacket 3cm or more and perform the processing
described on the left.
DA (Blue)
DB (White) If the wire lengths are not even, trim their ends with nippers to
DG (Yellow) the same length.
Drain wire (AWG20)

Stretch the drain wire and twist it from the base.

(3cm in length, 7 times or more)

3) Insert a cable.
Lift the end of the plug cover and insert a cable until it reaches
the other end of the cover (within 1mm from the other end).
Failure to do so may cause an improper crimping.
Metal contacts

4) Set the plug cover.

After the cable is inserted, put down the plug cover and set it to
the position where the metal contacts fit into the cover.

Metal contacts

5) Crimp the plug cover into the plug.

Pliers Hold the center of the plug cover with pliers and press it
vertically into the plug.

(To the next page)

7 - 13 7 - 13
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

(From the previous page)

6) Press the latches into the plug.

After crimping, press the latches located at both ends of the
plug cover into the plug.
Check that the cover is fixed to the plug with the latches.

[Correct example] 7) Check the crimped state from the side.

Check that the plug cover is horizontally-embedded to the plug.
Check also that the floating part of the cover is within 0.2mm.
0.2mm or less

Note: As shown in the wrong example on the left, if the cover is

not horizontally-embedded or the floating part is 0.2mm
or more, it may result in improper crimping.
[Wrong example] Press the plug cover firmly into the plug with pliers. (Refer
to the correct example.)

[Correct example] 8) Check the crimped state from the top.

Check that there is no clearance between the plug and the
cover.

Note: As shown in the wrong example on the left, if the latch is

not securely engaged, clearance occurs between the plug
and the cover.
Press the plug cover firmly into the plug with pliers. (Refer
[Wrong example]
to the correct example.)

Latches

Latch

Clearance

(Wiring completed)

7 - 14 7 - 14
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

7.2.5 Wiring procedures for the one-touch connector for power supply and FG

This section describes the wiring procedures for the one-touch connector used for
power supply and FG of the connector type compact I/O module.

Plug cover
Plug body 1) Check the connector.
Check that a plug cover is attached to the plug.

Note: Do not press the plug cover firmly into the plug before a
cable is inserted.
Metal contact
Once crimped, the plug can no longer be used.

2) Insert a cable. ( 1)
Lift the end of the plug cover and insert a cable until it reaches
the other end of the cover (within 1mm from the other end).
Failure to do so may cause an improper crimping.
Metal contacts
Note: Use cables applicable to the module.

3) Set the plug cover.

After the cable is inserted, put down the plug cover and set it to
the position where the metal contacts fit into the cover.

4) Crimp the plug cover into the plug.

Pliers Hold the center of the plug cover with pliers and press it
vertically into the plug.

5) Press the latches into the plug.

Pliers
After crimping, press the latches located at both ends of the
Latches
plug cover into the plug.
Check that the cover is fixed to the plug with the latches.

(To the next page)

7 - 15 7 - 15
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

(From the previous page)

[Correct example] 6) Check the crimped state from the side.

Check that the plug cover is horizontally-embedded to the plug.
Check also that the floating part of the cover is within 0.2mm.

0.2mm or less
Note: As shown in the wrong example on the left, if the cover is
not horizontally-embedded or the floating part is 0.2mm
or more, it may result in improper crimping.
[Wrong example] Press the plug cover firmly into the plug with pliers. (Refer
to the correct example.)

[Correct example] 7) Check the crimped state from the top.

Check that there is no clearance between the plug and the
cover.

Note: As shown in the wrong example on the left, if the latch is

not securely engaged, clearance occurs between the plug
and the cover.
Press the plug cover firmly into the plug with pliers. (Refer
[Wrong example]
to the correct example.)

Latches

Latch

Clearance

(Wiring completed)

1 When a cabtyre cable is used:

Strip the cable jacket 2cm or more.
If the wire lengths are not even, trim their ends with nippers to the same length.
2cm or more

Trim the wire ends to the same length

7 - 16 7 - 16
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

7.3 Handling of the Waterproof-type Remote I/O Module

7.3.1 List of dustproof and waterproof caps

The following table lists the model names of dustproof cap and waterproof cap
applicable to the CC-Link system waterproof-type remote I/O module.
Mitsubishi model name Specifications
1
Dustproof cap A6CAP-DC1 —
1
Waterproof cap A6CAP-WP1 Protection of degree IP67

1 A pack of A6CAP- 1 (manufactured by Mitsubishi) includes 20 pieces.

7.3.2 Waterproof plug attachment procedure

The attachment procedure for the waterproof plug supplied with the AJ65SBTW4-16
is shown below. In order to prevent water leakage, attach a waterproof plug to the
penetrating pipe for the transmission and module power-supply lines in the following
way.

1) Remove the nut and bushing from the penetrating pipe attached to the
module.

Nut Bush Penetrating pipe

2) Insert the waterproof plug into the penetrating pipe and secure it by tightening
the nut.
Tightening torque: 0.99 to 1.48N·m

Waterproof pulg

7 - 17 7 - 17
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

7.3.3 Wiring procedure for the terminal block

This section describes the wiring procedure of a terminal block to the waterproof-type
remote I/O module.
1) Remove the module front cover, and pass the cables through the through
pipe for the transmission and module power-supply lines.

2) Open the module top cover and remove the terminal block, then perform
wiring to the terminal block.

Terminal layout diagram

DA DG +24V 24G
CC-Link
DB SLD FG
cable

Power
cable

3) Secure the terminal block using screws, then fasten the module front and top
covers using screws.

4) Tighten the nut on the through pipe for the transmission and module power-
supply lines.

POINT
• Always install a waterproof plug to the unused through pipe for the transmission
and module power-supply lines. (Refer to Section 7.3.2.)
• When wiring the transmission and module power-supply lines, please take care
not to apply force in excess of 0.39N·m excessive force to the wiring at the inlet.
• In the event of the ambient temperature exceeding 56 °C after wiring the unit,
make sure to re-tighten the nuts.

7 - 18 7 - 18
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

7.4 Handling of the Low Profile Waterproof Type Remote I/O Module

7.4.1 List of waterproof caps

The model name of the waterproof cap applicable to the CC-Link system low profile
waterproof type remote I/O module (AJ65FBTA -16 ) is shown below. The following
table lists the model names of waterproof cap applicable to the CC-Link system low
profile waterproof type remote I/O module (AJ65FBTA -16 ).

Mitsubishi Product
Use
Model Name
Waterproof cap
A6CAP-WP2 For LINK OUT connector and I/O connector
(20 pieces, Sold separately)

POINT
• The waterproof cap (A6CAP-WP1) cannot be used.

7.4.2 Waterproof cap installation method

The installation method for the waterproof caps packed with the product is shown
below.
In order to prevent water penetration, install the waterproof caps on the unused Link
Out side connectors and I/O connectors using the following method.

1) Insert the waterproof cap in the empty connector on the main module, then
tighten it.
Tightening Torque Range: 0.29 to 0.34N·m

7 - 19 7 - 19
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

7.5 Connectors and Tools Used for Connecting the FCN Connector Cables

• When connecting the connector cables by crimp-contact, pressure-displacement or

WARNING
soldering, make sure to use the tools listed in the table below. Attach the connectors
securely to the module.

Three types of 40-pin connectors are available for the AJ65 BTCF1-32 and the
AJ65 BTCF1J-32 ; they are soldering type, pressure-displacement type and crimp-
contact type.
Please purchase the required 40-pin connector, and either pressure-displacement or
crimp-contact type tool according to the listing below.

(1) Connector types

Type Model name
Soldering type connector (Straight-out type) A6CON1
Crimp-contact type connector (Straight-out type) A6CON2
Pressure-displacement type connector (Flat cable type) A6CON3
Soldering type connector (Straight-out/diagonal-out type) A6CON4

(2) Crimp-contact and pressure-displacement type tools

Type Model name Cable size Manufacturer
Crimp-contact tool FCN-363T-T005/H AWG28 to 24
FCN-367T-T012/H
(locator plate) AWG28
FUJITSU COMPONENT
Pressure- FCN-707T-T001/H (strand cable)
LIMITED
displacement tool (cable cutter) AWG30
FCN-707T-T101/H (single cable)
(hand press)

7 - 20 7 - 20
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

7.6 Attaching and Removing the Protective Cover for the Compact Remote I/O Module

Covering the front of CC-Link system compact remote I/O module with a protective
cover can prevent the following accidents:
• Improper contact to the terminal block or connector.
• Module malfunction resulted from connector drop.
For the model name of the protective cover for the compact remote I/O module, see
Section 1.5.

Follow the procedure illustrated below to mount the protective cover on the module.

(1) In the case of A6CVR-8/16/32

<How to mount>
Hook the top of the protective cover onto the top of the remote I/O module, then
push the lower part of the cover toward the module until you hear a click sound.

Click

<How to remove>
Place your thumb under the protective cover and pull it upwards.

7 - 21 7 - 21
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

(2) In the case of A6CVR-VCE8/16

<How to mount>
Confirm the orientation of the protective cover as shown in the diagram below.
Then, attach the cover straight to the module as shown by the arrow and push in
securely until it stops.

CON A,B,C,D

Model No. of
protective cover

: Attach the protective cover, keeping its model No. and the CON A, B, C and D
in the same orientation.
Otherwise, the cover cannot be attached.

Securely fix tabs of the protective cover to the groove of the module as shown
below.
Note that the fixing tab positions vary with the protective cover used.

In the case of A6CVR-VCE16

Tab

Tab

(Left side) (Right side)

In the case of A6CVR-VCE8

Tab Tab

(Left side) (Right side)

7 - 22 7 - 22
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

<How to remove>
Extend the width of protective cover slightly as shown by the arrow 1). Then, pull
it out vertically from the module as shown by the arrow 2).

1)

1)

2)

POINT
(1) When attaching the protective cover, ensure the space of 50mm or more between the target
module and the modules on the right and left sides. Also, ensure the space of 100mm or more
over the upper part of the module, so that the cover can be pulled upward.
Structure, other device, parts, etc. Structure, other device, parts, etc.

Control panel, etc.

CON A

1 2 4 1 2 4 8 102040
B RATE STATI ON NO.
ON
B

PWL RUN L ERR.

8 9 A BC DE F

0 1 2 3 4 5 6 7
C
DY

X
8

0
9

1
A

2
B

AJ65VBTCE32- 16DT
C

4
D

100mm or more
>PC<
6
E

7
F

5mm or more 5mm or more

(2) Fix the wiring with a clamp or similar parts. Failure to do so may apply force to the protective
cover, resulting in it falling from the module. In addition, the wiring cable may be damaged.
(3) When mounting both of the Terminal resistor attached one-touch connector plug (A6CON-
TR11) and Online connector for communication (A6CON-LJ5P), make sure to follow the
procedure provided below.
Failure to do so may cause the terminating resistor, protective cover and communication cable
to interfere with each other.
• Tilt the terminating resistor toward 1) or 2) as shown in the diagram below, and then attach
the protective cover.
• Connect the Terminal resistor attached one-touch connector plug to CON B.
1) 2) Terminating resistor

Communication cable

Online connector for communication

CON A B C D

7 - 23 7 - 23
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

7.7 Connection Method of CC-Link Dedicated Cable

This section describes how to connect the compact remote I/O module to the master
module using CC-Link dedicated cables.

• Shut off the external power supply (all phases) used in the system before wiring.
WARNING
Failure to do so may result in electric shock or damage to the product.
• After wiring, attach the included terminal cover to the module before turning it on for
operation.
Failure to do so may result in electric shock.
• Shut off the external power supply (all phases) used in the system before cleaning
the module or retightening the terminal block screw. Failure to do so may cause the
module to fail or malfunction.

• Do not install the control lines or communication cables together with the main
CAUTION
circuit lines or power cables.
Keep a distance of 100mm (3.9 inches) or more between them.
Failure to do so may result in malfunction due to noise.
• Ground the FG terminal to the protective ground conductor dedicated to the
programmable controller.
Failure to do so may result in electric shock or malfunction.
• Tighten any unused terminal screws within the specified torque range (0.42 to
0.50N•m).
Failure to do so may cause a short circuit due to contact with a solderless terminal.
• Use applicable solderless terminals and tighten them within the specified torque
range. If any solderless spade terminal is used, it may be disconnected when the
terminal screw comes loose, resulting in failure.
• Check the rated voltage and terminal layout before wiring to the module, and
connect the cables correctly.
Connecting a power supply with a different voltage rating or incorrect wiring may
cause a fire or failure.
• Securely connect the cable connectors.
Poor contact may cause malfunction.
• Place the cables in a duct or clamp them.
If not, dangling cable may swing or inadvertently be pulled, resulting in damage to
the module or cables or malfunction due to poor contact.
• Do not install the control lines or communication cables together with the main
circuit lines or power cables.
Failure to do so may result in malfunction due to noise.
• When disconnecting the cable from the module, do not pull the cable by the cable
part.
For the cable with connector, hold the connector part of the cable.
For the cable without connector, loosen the screw first and remove it.
Pulling the cable connected to the module may result in malfunction or damage to
the module or cable.

7 - 24 7 - 24
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

(1) The following figure shows how to connect compact remote I/O modules to a
master module.
Terminating Master module
resistor
NC
(Blue) DA
NC
(White) DB
NC
(Yellow) DG
Compact remote I/O module 1 Compact remote I/O module 2
NC
SLD DA DG +24V 24G DA DG +24V 24G
NC
FG DB SLD FG DB SLD FG
Terminating
resistor 1

CC-Link dedicated cable 2

[Simplified diagram]
Compact remote Compact remote
Master module I/O module 1 I/O module 2
(Blue) (Blue) (Blue) (Blue)
DA DA DA
(White) (White) (White) (White)
DB DB DB
Terminating (Yellow) (Yellow) (Yellow) (Yellow)
Terminating
resistor DG DG DG resistor
SLD CC-Link SLD CC-Link SLD
dedicated cable dedicated cable
FG FG FG

1 Connect a terminating resistor as shown below to the compact remote I/O module
connected as the last station. (Terminating resistors are provided with a master
module.)

DA DG +24V 24G

DB SLD FG

Terminating resistor

2 Use CC-Link dedicated cables in the CC-Link systems.

Performance of the CC-Link system cannot be guaranteed if any cables other that
the CC-Link dedicated cables are used.
For the specifications and any inquiries on the CC-Link dedicated cables, refer to
the following:
CC-Link Partner Association Website: http://www.cc-link.org/

POINT
Compact remote I/O modules with an input response of 0.2ms are more susceptible
to noise interference than other modules. Keep the wiring of the I/O module away
from power cables as much as possible.

7 - 25 7 - 25
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

(2) The following figure shows how to connect connector type remote I/O modules to a
master module.
Master module
Terminating CONA CONA
1 1
resistor *1 NC 2
1 DA
2
1 DA
2 DB 2 DB
(Blue) DA 3 3 DG 3 3 DG
NC 4 4 NC 4 4 NC
5 5
(White) DB 5 SLD 5 SLD
NC CONB CONB
(Yellow) DG 1 1 DA 1 1 DA
NC 2 2 DB 2 2 DB
3 3 DG 3 3 DG
SLD 4 4
4 NC 4 NC
NC 5 5
5 SLD Terminating 5 SLD
FG
resistor *1

Ver.1.10-compatible
CC-Link dedicated cable*2

[Simplified diagram]
Connector type remote Connector type remote
Master module I/O module 1 I/O module 2
(Blue) (Blue) (Blue) (Blue)
DA DA DA
(White) (White) (White) (White)
DB DB DB
Terminating (Yellow) (Yellow) (Yellow) (Yellow) Terminating
resistor DG DG DG resistor
SLD SLD SLD
Ver.1.10-compatible Ver.1.10-compatible
FG CC-Link dedicated cable FG CC-Link dedicated cable FG

1 Connect the following type of terminating resistor when a connector type remote
I/O module is connected as the last station.
5 4 3 2 1
54 32 1

A6CON-TR11

2 Use CC-Link dedicated cables in the CC-Link systems.

Performance of the CC-Link system cannot be guaranteed if any cables other that
the CC-Link dedicated cables are used.
For the specifications and any inquiries on the CC-Link dedicated cables, refer to
the following:
CC-Link Partner Association Website: http://www.cc-link.org/

POINT
Compact remote I/O modules with an input response of 0.2ms are more susceptible
to noise interference than other modules. Keep the wiring of the I/O module away
from power cables as much as possible.

7 - 26 7 - 26
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

(3) The following figure shows how to connect a one-touch connector and online
connector to the remote I/O module.

Online connector for

communication
(A6CON-LJ5P)

Connector plug
(A6CON-L5P)

Online connector for

power supply and FG
(A6CON-PWJ5P)
Connector plug
(A6CON-PW5P, A6CON-PW5P-SOD)

POINT
• For a one-touch connector for communication, use Ver.1.10-compatible CC-Link
dedicated cables (FANC-110SBH, FA-CBL200PSBH, or CS-110).
Ver.1.10-compatible CC-Link dedicated cables other than those above, CC-Link
dedicated cables, and CC-Link dedicated high-performance cables are not
supported.
• To connect or remove a one-touch connector to/from an online connector, refer to
the manual included with the online connector.

7 - 27 7 - 27
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

7.8 Handling of Spring Clamp Terminal Block Type Remote I/O Module

7.8.1 Installation and removal of the spring clamp terminal block

(1) Installing the spring clamp terminal block

How to install a 2-piece spring clamp terminal block is shown below.
Secure the terminal block part using the following method. Incomplete
installation may cause fall, short circuit or malfunction.

1) Push the spring clamp terminal block fixing tabs of the 2-piece terminal block
in the arrow direction until a click can be heard.

2-piece terminal block

Spring clamp terminal
block fixing tabs

2) Connect the connector (female) of the 2-piece terminal block to the connector
(male) of the module body and press it until a click can be heard. Check that
both of two fixing tabs are inserted completely.

Connector

Module body

3) Tighten the 2-piece terminal block fixing screws. (Tightening torque range:
0.34 to 0.46N·m)
2-piece terminal
block fixing screws

Screwdriver

C
D

(2) Removing the spring clamp terminal block

Remove the spring clamp terminal block in reverse order of the above installation
procedure.
1) Loosen the 2-piece terminal block fixing screws.
2) Pull out the spring clamp terminal block fixing tabs.
3) Lift the 2-piece terminal block to remove it from the main body.

7 - 28 7 - 28
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

7.8.2 Procedure for wiring the spring clamp terminal block

This section describes the procedure for connecting a cable to the spring clamp
terminal block remote I/O module.

(1) Precaution for connecting or disconnecting cables

(a) Insert only one wire into the circular shaped hole of the spring clamp terminal
block. Inserting two or more wires may result in a poor contact to the terminal
part.
(b) Strip the wire according to the specification. If the wire strip length is too long,
the exposed conductive part may cause electric shock or short circuit. If the
wire strip length is too short, it may result in a poor contact to the spring clamp
terminal part.
(c) When using a spring clamp terminal block tool, follow the instruction below.
Failure to do so may cause damage of the spring clamp terminal part or the
terminal block resin part.
• Use a dedicated tool for a spring clamp terminal block.
• Do not insert the wire or the bar solderless terminal before inserting the tool
into the square shaped hole.
• Insert the tool vertically into the hole.

(2) Connecting a cable

(a) Insert the tool vertically all the way inside the square shaped hole of the
remote I/O module.
(b) Insert the wire or the bar solderless terminal into the circular shaped hole, and
remove the tool from the hole.
(c) Check that the wire or the bar solderless terminal is firmly clamped by pulling
it lightly.

Square shaped hole

Circular shaped hole

Wire
Tool

Wire strip length:

8mm to 11mm

(3) Disconnecting a cable

(a) Insert the tool vertically all the way inside the square shaped hole of the
remote I/O module.
(b) Pull the wire or the bar solderless terminal out of the hole.

7 - 29 7 - 29
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

(4) Recommended product list

Applicable wire
Product name Model name Contact
size
Tool (dedicated to spring
KD-5339 — Mitsubishi Electric System Service Co., Ltd.
clamp terminal block)
2
TE 0.5 0.5mm
2
TE 0.75 0.75mm
Bar solderless terminal 1 2
TE 1 0.9 to 1.0mm
2 NICHIFU TERMINAL MFG. Co., Ltd.
TE 1.5 1.25 to 1.5mm
Dedicated bar solderless
NH79 —
terminal tool

1 Use this product when doing the terminal treatment of the wire and inserting it into
the spring clamp terminal block.

7 - 30 7 - 30
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

7.9 Attaching Mounting Brackets to the Module

7.9.1 Attachment of mounting brackets

This section describes the procedures for directly installing the AJ65VBTS - or
AJ65VBTCE - to a control panel using mounting brackets and screws. If the
module is not fixed securely, it can cause drop of the module, short circuit, or
malfunction.

(1) Align the projections of a mounting bracket with the corresponding slots of the
module.

(2) Obliquely insert the projections to the slots, and press down the mounting bracket
in the direction of an arrow until it clicks.

(3) Screw the mounting bracket to a control panel. (Tightening torque range: 0.82 to
1.11N·m)

C
D

Control panel

7 - 31 7 - 31
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

7.9.2 Precautions for attaching mounting brackets

The mounting brackets can be attached differently depending on the modules.

Attach them to two positions.

(1) AJ65VBTS -16 The mounting brackets can be attached as shown below
(two different ways).

ON ON
PW L RUN L ERR. PW L RUN L ERR.
B RATE STATION NO.

B RATE STATION NO.

1 2 4 1 2 4 8 1020 40

1 2 4 1 2 4 8 1020 40
AJ65VBTS2-16T AJ65VBTS2-16T
0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7

8 9 A B C D E F 8 9 A B C D E F

NC Y0 Y1 Y2 Y3 Y4 Y5 Y6 Y7 Y8 Y9 YA YB YC YD YE YF NC Y0 Y1 Y2 Y3 Y4 Y5 Y6 Y7 Y8 Y9 YA YB YC YD YE YF

COM+ COM+ COM+ COM+

COM- NC COM- NC

CON A B C D CON A B C D

(2) AJ65VBTS -32 The mounting brackets can be attached as shown below
(only one way).
ON
PW L RUN
L ERR.
B RATESTATION NO.
1 2 4 1 2 4 8 102040

AJ65VBTS3-32D
0 1 2 3 4 5 6 7

8 9 A B CD E F
NC X0 X1 X2 X3 X4 X5 X6 X7 X8 X9 XA XB XC XD XE XF NC X10 X11 X12 X13 X14 X15 X16 X17 X18 X19 X1A X1B X1C X1D X1E X1F

COM1+ COM1+ COM2+ COM2+

COM1- COM1- COM2- COM2-

CON A B C D

(3) AJ65VBTCE -8 The mounting brackets can be attached as shown below

(two different ways).

CON ON CON ON
1 1
2 2
A 3 A 3
4 4
5 5
6 6
7 7
8 8
9 9
B 10 B 10

40 S 40 S
T T
20 A 20 A
10 T
C 10 T
C I I
8 O 8 O
4 N 4 N
2 N 2 N
1 O. 1 O.
D 4 B D 4 B
R R
2 A 2 A
T T
1 E 1 E

AJ65VBTCE3-8D A J65VBTCE3-8D
PW PW
X0 L RUN
X0 L RUN
L ERR. L ERR.
X1 X1
0 0
1 1
X2 2
X2 2
3 3
X3 4 X3 4
5 5
6 6
X4 7 X4 7

X5 X5

X6 X6

X7 X7

7 - 32 7 - 32
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

(4) AJ65VBTCE -16 , AJ65VBTCE -32

The mounting brackets can be attached as shown below (two different ways).

ON ON
PW L RUNL ERR. AJ65VBTCE3-16D PW L RUNL ERR. AJ65VBTCE3-16D
1 2 4 1 2 4 8 102040

1 2 4 1 2 4 8 102040
B RATE STATION NO.

B RATE STATION NO.

0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7

8 9 A B C D E F 8 9 A B C D E F

X 0 1 2 3 4 5 6 7 X 0 1 2 3 4 5 6 7

CON A B C D X 8 9 A B C D E F CON A B C D X 8 9 A B C D E F

POINT
• Do not attach the mounting brackets in any ways other than those described
above.

ON
PW L RUN L ERR.
B RATE STATION NO.
1 2 4 1 2 4 8 1020 40

AJ65VBTS2-16T
0 1 2 3 4 5 6 7

8 9 A B C D E F

NC Y0 Y1 Y2 Y3 Y4 Y5 Y6 Y7 Y8 Y9 YA YB YC YD YE YF

COM+ COM+

COM- NC

CON A B C D

7 - 33 7 - 33
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

7.10 Mounting the DIN Rail Adapter

7.10.1 Specifications

The following table shows the specifications of the DIN rail adapter.

Model
A6DIN1C
Item
Mountable module AJ65DBTB1-32D, AJ65DBTB1-32T1,
AJ65DBTB1-32R, AJ65DBTB1-32DT1,
AJ65DBTB1-32DR
External dimensions 174mm (6.85 inches) 68mm (2.68 inches)
10mm (0.39 inches)
Weight 0.05kg
Applicable DIN rail type (conforms to IEC TH35-7.5Fe, TH35-7.5Al, TH35-15Fe
60715)

7.10.2 Handling precautions

(1) The DIN rail adapter is made from resin. Do not drop or apply strong
shock to the adapter.

(2) Mounting pitch

When installing a DIN rail to a control panel, keep mounting pitches 200mm (7.87
inches) or less.

7.10.3 Attaching the DIN rail adapter to the module

Use two M4 screws (length: 10mm (0.39 inches)) to attach the DIN rail adapter to the
AJ65DBTB1-32 type compact remote I/O module.
The tightening torque range is 0.78 to 1.18N•m.

7 - 34 7 - 34
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

7.10.4 Mounting the module to a DIN rail

This section describes how to mount/remove the module to/from a DIN rail.

(1) Mounting to a DIN rail

Mount the module with the DIN rail adapter attached to a DIN rail as follows.
(a) Insert the groove for DIN rail adapter into the topside of the DIN rail.
(b) Fix the module by pressing it against the DIN rail.

(c) When multiple DIN rail adapters are installed on the DIN rail, even though
the gaps among DIN rail adapters are filled, the spaces of 4mm (0.16 inches)
are left among the modules.

2-M4 installation screw (M4 mounting screw)

2 (0.08) 66 (2.60)
10 (0.39)
55 (2.17)
172 (6.77)
161 (6.34)
2 (0.08)

Unit: mm (inch)

7 - 35 7 - 35
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

(2) Removing the module from a DIN rail

Remove the module from a DIN rail as follows.
(a) Pull the hook at the bottom of the DIN adapter downward with flathead
screwdriver (6 100).
(b) With the hook pulled out, pull the module forward and remove the module
from the DIN rail.

7 - 36 7 - 36
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

7.11 Common Terminal Block

Model
Item A2CCOM-TB
Mountable module AJ65DBTB1-32D, AJ65DBTB1-32T1, AJ65DBTB1-32R,
AJ65DBTB1-32DT1, AJ65DBTB1-32DR
External dimensions 125mm (4.92 inches) 64mm (2.52 inches) 13mm (0.51
inches)
Weight 0.12kg

64(2.52)

(0.33 9 = 3.01)
8.5 9 = 76.5

125(4.92)
76.5(3.01)

17.6(0.69)
13.35(0.53)

8(0.31)

4(0.16) 4.5(0.18)
44(1.73)
54(2.13)
3(0.12)
2.5(0.10)

2(0.08)

32.5(1.28)
13(0.51)
3.5(0.14)

21(0.83)
32(1.26)

7 - 37 7 - 37
7 HANDLING OF COMPACT REMOTE I/O MODULES
MELSEC-A

(1) Usage example of common terminal block

(a) Example of usage for input module, AJ65DBTB1-32D
Input terminal block

Common terminal block

X0
X1
X2
X3
X4
X5
X6
X7
COM1
Common terminal block X8
X9
XA
XB
XC
XD
XE
XF
COM2

(b) Example of usage for output module, AJ65DBTB1-32R

output terminal block

Common terminal block Load

X0
Load
X1
Load
X2
Load
X3
Load
X4
Load
X5
Load
X6
Load
X7
COM1
Load
Common terminal block X8
Load
X9
Load
XA
Load
XB
Load
XC
Load
XD
Load
XE
Load
XF
COM2

7 - 38 7 - 38
 8 TROUBLESHOOTING
MELSEC-A

8 TROUBLESHOOTING

8.1 Verifying Errors from LED Status

The following table lists causes and corrective actions for errors indicated by LEDs on
the compact remote I/O module when the SW, M/S and PRM LEDs are all off (i.e. the
master module is set properly) in the system configuration example shown below.
Power supply

CPU Master
module

Station number 1 Station number 2 Station number 3

Compact remote Compact remote Compact remote
I/O module A I/O module B I/O module C

LED status
Master Remote I/O module Cause Corrective action
module A B C
PW PW PW
L RUN L RUN L RUN Normal —
L ERR. L ERR. L ERR.
PW PW PW Since the LEDs on the compact remote Check the voltage of the 24V power supply, and
L RUN L RUN L RUN I/O module A are all off, the 24V power supply the proper power to the compact remote
L ERR. L ERR. L ERR. is not supplied or voltage is low. I/O module.
PW PW PW The compact remote I/O module A is Exchange the compact remote I/O module.
L RUN L RUN L RUN malfunctioning and the LEDs are
L ERR. L ERR. L ERR. unstable (all lights are off, in many
cases).
PW PW PW The L RUN lights on the compact Identify the disconnected point by referring to
TIME
L RUN L RUN L RUN remote I/O module B and beyond are the LED status, and correct it.
LINE
L ERR. L ERR. L ERR. off, indicating the transmission cable
or
between the compact remote I/O
TIME
module A and B has been disconnected
LINE
or removed from the terminal block.

8 PW PW PW The transmission cable is shorted. Find the shorted cable among the three
L RUN L RUN L RUN transmission cables and repair it.
L ERR. L ERR. L ERR.
PW PW PW The transmission cable is wired Verify wiring in the terminal box of the compact
L RUN L RUN L RUN incorrectly. remote I/O module and correct.
L ERR. L ERR. L ERR.
PW PW PW The L RUN lights on the compact Restart the power supply after the overlapped
L RUN L RUN L RUN remote I/O modules A and C are off, station numbers for the compact remote I/O
L ERR. L ERR. L ERR. indicating the station numbers for A and modules are corrected.
C are overlapping.
: lit, : unlit, : flashing, : lit, flashing or unlit

8-1 8-1
8 TROUBLESHOOTING
MELSEC-A

LED status
Master Remote I/O module Cause Corrective action
module A B C
PW PW PW The L RUN light on the compact remote Restart the power supply after the transmission
L RUN L RUN L RUN I/O module B is off, indicating the speed is set correctly.
L ERR. L ERR. L ERR. transmission speed setting for module B
is invalid within the setting range (0 to 4).
PW PW PW The L ERR. of the compact remote I/O Return the setting switch of the compact remote
TIME L RUN L RUN L RUN module C is flashing at fixed intervals, I/O module to the original position.
LINE L ERR. L ERR. L ERR. indicating the setting switch for module
or C has been changed during normal
TIME operation.
LINE PW PW PW The L RUN of the compact remote I/O Correct the setting switch of the compact remote
L RUN L RUN L RUN module A is off and L ERR. of the same I/O module, and restart the power supply.
L ERR. L ERR. L ERR. module is lit, indicating the setting
switch for module A is set out of range
(transmission speed: 5 to 9, station
number: 65 or greater).
PW PW PW The L ERR. of the compact remote I/O Correctly perform grounding of the FGs for the
L RUN L RUN L RUN module B is lit, indicating that module B master module and all compact remote I/O
L ERR. L ERR. L ERR. is being affected by noise. (L RUN may modules.
be off.)
TIME
PW PW PW The L ERR. lights on the compact Verify the grounding of the SLD of the
LINE
L RUN L RUN L RUN remote I/O module B and beyond are lit, transmission cable.
or
L ERR. L ERR. L ERR. indicating the transmission cable is Separate the wire from the power cable as
TIME
affected by noise in the area between much as possible (100mm (3.94 inches) or
LINE
modules A and B. (L RUN may be off.) more).
PW PW PW A terminal resistor is not attached. Check if a terminal resistor is attached.
L RUN L RUN L RUN (L RUN may be off.)
L ERR. L ERR. L ERR.
: lit, : unlit, : flashing, : lit, flashing or unlit

8-2 8-2
8 TROUBLESHOOTING
MELSEC-A

8.2 Examples of Errors for Compact Remote I/O Modules

This section explains examples of errors that occur in the input circuit, and the
appropriate corrective actions.

8.2.1 Errors occurring in the input circuit and corrective actions

Examples of errors that occur in the input circuit and corrective actions are explained
below:
Error status Cause Corrective action
Example 1 Input signals do not turn off. • Activation via the LED display switch. • Connect an appropriate resistor as shown
below so that the current flowing along the
DC input (sink) input module becomes lower than OFF
current.
DC input (sink)
Leakage current Input
module

Resistor Input
module

A calculation example used to obtain the

resistance value to be connected is shown
on the following page.
Example 2 Input signals do not turn off. • Sneak path due to the use of two power • Reduce the number of power supplies
supplies. from two to one.
DC input • Connect a diode to prevent sneak path.
(as below)
E1 E2 Input DC input
module

E1 E2 Input
module
E1 > E2

Example 3 Input signals do not turn off. • Input switch leakage current (driving with a • Connect the appropriate resistor so that the
contactless switch). terminal-to-terminal voltage of the input
module is below the OFF voltage value.
AC input AC input

Leakage Input Input

current R module
module

Power supply 0.1 to 0.47µF + 47 to 120Ω (1/2W) is

recommended for the CR constant.
Example 4 Input signals do not turn off. • Driving using a limit switch with neon lamp. • Same as Example 3.
AC input • Or, create a completely separate display
circuit.
Leakage Input
current module

Power supply

Example 5 Input signals do not turn off. • Leakage current due to line capacity of the • Same as Example 3.
wiring cable. • However, this problem will not occur if the
The line capacity "C" of a twisted pair wire is power supply as shown below is provided
about C=100PF/m. at the input device side.
AC input AC input

Leakage Input Input

current module module

Power supply Power supply

8-3 8-3
8 TROUBLESHOOTING
MELSEC-A

<Sample calculation for Example 1>

When a switch with LED indicator, giving leakage current of 3mA at maximum when
24VDC power is supplied to the AJ65SBTB1-16D
AJ65SBTB1-16D

Leakage Input module

current mA

24VDC

(1) 1.7mA or less OFF current of the AJ65SBTB1-16D is not satisfied. Hence, connect a
resistor as shown below.
AJ65SBTB1-16D
3mA
Iz=1.7mA

R=1.3mA
Input impedance
R
3.3K

24VDC

(2) Calculate the resistance value R as shown below.

To satisfy 1.7mA or less OFF current of the AJ65SBTB1-16D, connect a resistor
which flows 1.3mA or more.

IR: IZ=Z (Input impedance): R

IZ 1.7
R Z (Input impedance) = 3.3=4.31[k ]
IR 1.3

Supposing that the resistance R is 3.9k , the power capacity W of resistor R is:
W = (Input voltage) 2 ÷ R = 26.42 ÷ 3900 = 0.179 (W)

(3) Connect a resistor of 3.9 (k ) and 1 to 2 (W) to a terminal which may cause an error,
since the power capacity of a resistor is selected so that it will be 3 to 5 times greater
than the actual power consumption.

(4) Also, OFF voltage when resistor R is connected will be as follows.

1
3[mA] 5.36[V]
1 1
3.9[k ] 3.3[k ]

This satisfies 6V or less OFF voltage of AJ65SBTB1-16D.

8-4 8-4
8 TROUBLESHOOTING
MELSEC-A

8.2.2 Errors occurring in the output circuit and corrective action

Examples of errors that may occur in the output circuit and the respective corrective
action are described below.

(1) When AJ65SBTB1-16T or AJ65SBTB1-32T is used

Condition Cause Corrective action

Example 1 When an LED is connected as a load, sometimes For the output modules Connect a resistor with 5 to
the LED dimly lights up even when the output listed below, the output 50kΩ in parallel to the load
module is turned off. module specification and LED.
(Example) LED push button by Izumi Electric, Co.: the leak current
ALFN22211DNR specification value during
OFF are 24VDC 0.5A and
CC-Link compact-type
remote output module Countermeasure 0.25mA, respectively (the
leak current during OFF is
specified as above since
LED
an MOS with a built-in
24 V DC protection function and
power
supply PET transistor output are
used.)
Example 2 When a segment LED display device is connected Connect a pull-up resistor
<Applicable modules>
as a load, the display contents sometimes become with 5 to 50kΩ and 0.5(W)
AJ65SBTB1-16T,
incorrect. between the 24VDC power
AJ65SBTB1-32T
(Example) M7E digital display unit (height of supply and the output
character 14mm) by Omron, Co.: M7E- module output.
01DBN2

CC-Link compact-
type remote Countermeasure Digital display unit
output module (input signal section)

Dedicated
IC
24 V DC
power
supply

8-5 8-5
8 TROUBLESHOOTING
MELSEC-A

(2) When AJ65SBTB2(N)-8S or AJ65SBTB2(N)-16S is used

Condition Cause Corrective action

Example 1 Excessive voltage • The load is half-wave rectified internally. • Connect a resistor of several tens
is applied to the (Some solenoids do this process.) KΩ to several hundreds KΩ to both
output OFF load. CC-Link compact remote
ends of the load.
triac output module
When this type of method is used,
D1 [1]
no problems will occur in the output
elements, but the diode that is built
in the load may deteriorate and
Load may be damaged.

Resistor
[2]

• When the polarity of the power supply is

[1], C is charging. When the polarity is [2],
Load
the voltage charged in C + power supply
voltage is applied to both ends of D1. The
maximum value of the voltage is about
2.2E.

Example 2 The load is not • Leakage current due to built-in surge • Connect a resistor to both ends of the
turned OFF. suppressor. load.
(Triac output) Caution is required when the wiring
distance from the output card to
CC-Link compact remote the load is long, since there may
triac output module be leakage current due to the line
Load
capacity.

Resistor

Leakage current

Load

Example 3 Time limit • Drive the relay first, and then drive the
changes when CR type timer at that contact.
the load is a CR
Caution is required as indicated in
type timer. Example 1 since the internal circuit
(Triac output) CC-Link compact remote may be half-wave rectified
triac output module CR depending on the timer.
timer
Resistor
Leakage current

CR timer

Calculate the resistor

constant according to
the load.

8-6 8-6
8 TROUBLESHOOTING
MELSEC-A

Condition Cause Corrective action

Example 4 The load is not • The load current is lower than the minimum load current. • Connect a resistor to both
turned OFF. Surge suppressor
ends of a load so that the
CC-Link compact remote
(Triac output) triac output module load current is higher than
the minimum load current.
Phototriac
Resistor

Control
circuit Load

Load

Triac

• When the load current is lower than the minimum load

current of the output module, the triac does not operate
since the load current flows into a phototriac as shown
below.
When an inductive load is connected, the load may not
be turned OFF since surge at the time of OFF is applied
to the phototriac.

8-7 8-7
8 TROUBLESHOOTING
MELSEC-A

(3) When AJ65AJ65SBTB1-8T, AJ65SBTB2-8T, AJ65SBTB1-16T, AJ65SBTB2-16T,

AJ65SBTB1-32T, AJ65SBTC1-32T, AJ65SBTB32-8DT, AJ65SBTB1-16DT,
AJ65SBTB1-16DT1, AJ65SBTB32-16DT, AJ65SBTB1-32DT,
AJ65SBTB1-32DT1, AJ65SBTC4-16DT, AJ65SBTC1-32DT,
AJ65SBTC1-32DT1, or AJ65SBTW4-16DT is used

Condition Cause Corrective action

Example 1 The load does When the load built into the capacitor is connected to the external load, • Install fast
not turn Off. a resonance may occur due to the inductor of the wiring and the load of recovery diode
the capacitor. This may lead to reverse current in output transistor. (1A, 100V or
Due to the reverse current, the protection circuit for output transistor more) in series
might operate, and the outputs might not be turned on. with the
external load.
Note: Such as SSR (Solid state relay) may incorporate a capacitor for
countermeasures against noise, etc. When the situation above
occurs, confirm if a capacitor is incorporated to the manufacturer.

Install fast recovery diode. CC-Link system compact type remote I/O module

Load with built-in condenser

Yn

24VDC 24VDC

COM Constant-
voltage circuit
COM

8-8 8-8
8 TROUBLESHOOTING
MELSEC-A

(4) When output module, combined module is used

Condition Cause Corrective action

Example 1 When the Erroneous output due to the stray (1) When the external power turns ON/OFF, check that the
external power capacitance (C) between collector and external power supply rising edge must be 10ms or more,
supply turns on, emitter of photocoupler. and switch the SW1 to the primary side of external power
the load turns on There is no erroneous supply.
for a moment. output at normal road. Primary side Secondary
An erroneous output may external power side
occur at high sensitivity load SW1 supply programmable
(such as solid state relay) controller

(2) When switching to the secondary side of the external

power supply is required, the external power supply rising
edge connected a condenser must be slow, and measured
10ms or more.

Sink output

Y0

Load

(1) If the external power supply is

R1
turned on precipitously, Ic current CTL+
SW
flows due to the stray capacitance C1
COM-
(C) between collector and emitter
24V
of photocoupler.
(2) Ic current flows to the next stage of Source output
transister Tr1 gate and Y0 output Y0

turns on by 100 s
Load

R1
CTL-
SW: External power SW
supply (24V) at On C1
COM+
10ms or less
24V

* The measures are ineffective in the following modules due to

the characteristic of the external power supply circuit
Output Y0
• AJ65SBTB1-8TE
Approx.100 s • AJ65SBTB1-16TE

R1: Several tens of ohms

Power capacity (external power supply current*1)2

resistance value
(3 to 5)*2

C1: several hundreds of microfarads 50V

*1 Refer to consumption current of the external power supply
for modules used in this manual.
*2 Select the power capacity of resistance to be 3 to 5 times
lager than the actual power consumption.

(Example)
R1=40 , C1=300 F
Use the below expression to calculated a time constant
C1 R1=300 10-6 40
=12 10-3s
=12ms

8-9 8-9
8 TROUBLESHOOTING
MELSEC-A

Condition Cause Corrective action

Example 2 The load which The load [2] which was turned OFF may Take action in the following (1) or (2).
was turned OFF is be turned ON due to back electromotive (1) To prevent the generation of the back electromotive
turned ON for a force at the time of power-off [1] if an force, connect diode in parallel with load where the back
moment at power- inductive load is used. electromotive force has been generated.
off. (Transistor
Output module, Source output
output) ombined module
Source output Back electromotive [3]
force [3]
Load
Y0 Back electromotive
ON force
Load
[2]
Load
Y1
OFF

[1]
Sink output
COM+
Shut off [3]
Back electromotive
CTL- force
Load

Output module,
ombined module
Sink output Back electromotive [3]
force
Load
(2) Install a diode between the positive and negative external
Y0
ON power supply to allow an electric current to pass another
current path.
[2]
Load When the corrective action shown in the example 1 is
Y1
OFF taken simultaneously, the diode must be installed in
parallel with the C1 and R1.
[1]
Source output Back electromotive [3]
Shut off force
COM- Load
Y0
ON
CTL+
[2]
Load
Y1
OFF
[1]
Shut off

COM+
D1
C1 R1
CTL-
Example 1

* The measures are ineffective in the following modules

due to the characteristic of the external power supply
circuit
• AJ65SBTB1-8TE
• AJ65SBTB1-16TE
Sink output Back electromotive [3]
force
Load
Y0
ON

[2]
Load
Y1
OFF
[1]
Shut off

COM-
D1
C1 R1
CTL+
Example 1

D1: Reverse voltage VR (VRM)…*1,

Forward current IF (IFM)…*2
*1 Approximately 10times higher than the rated voltage
in the specifications
Example: 24VDC→Approximately 200V
*2 More than twice as much as the maximum load
current (common) in the specifications
Example: 2A/1 common→4A or more

8 - 10 8 - 10
8 TROUBLESHOOTING
MELSEC-A

Condition Cause Corrective action

Example 3 The load operates The polarity of the external power supply Connect the polarity correctly.
due to powering is connected in reverse.
Transistor
on the external output module
Load
power supply. Y0 Incorrect Correct
(transistor output) External
power
supply
COM

Output element
protection diode

When the polarity is connected in

reverse, current may flow across an
output element protection diode.

8 - 11 8 - 11
APPENDICES
MELSEC-A

APPENDICES
Appendix 1 External Dimensions
Appendix 1.1 AJ65SBTB1-8 remote I/O module
The external dimensions for the AJ65SBTB1-8 remote I/O module are shown below.
(1.57)
40

87.3 (3.44)
+1 +0.04
78.3 0 (3.1 0 ) (Mounting pitch)
2-4.5 5.1 mounting holes (M4 screw)

STATION NO. B RATE

X0 1 2 3 4 5 6 7
(0.65)

40 20 10 8 4 2 1 4 2 1
16.5

ON
(A

A J65SBTB1-8D

(0.3)
pp

7.5
DA DG +24V 24G X0 X2 X4 X6 COM
ro
(1.97)

DB SLD (FG) X1 X3 X5 X7 COM

x.
50

DIN rail center

10
5

7.9
)

(0.31)
(0.16)
4

(0.08)

11
(When the protective cover attached.) (0.43)
2

STATION NO. B RATE

X0 1 2 3 4 5 6 7 40 20 10 8 4 2 1 4 2 1

ON

A J65SBTB1-8D
DA DG +24V 24G X0 X2 X4 X6 COM
DB SLD (FG) X1 X3 X5 X7 COM
(2.44)
62

(1.36)
34.5

PULL
A6CVR-8

87.3 (3.44) A
4 38.5 (1.52)
59 (2.32)
(0.16) 52.5 (2.07)
30.5 (1.20)

Unit: mm (inch)

App - 1 App - 1
 APPENDICES
MELSEC-A

Appendix 1.2 AJ65SBTB1-16 remote I/O module

The external dimensions for the AJ65SBTB1-16 remote I/O module are shown
below.
(1.57)
40

118 (4.65)
109 +10 (4.29+0.04
0 ) (Mounting pitch)
2-4.5 5.1 mounting holes (M4 screw)

STATION NO. B RATE

X0 1 2 3 4 5 6 7 X8 9 A B C D E F
(0.65)

40 20 10 8 4 2 1 4 2 1
16.5

ON

AJ65SBTB1-16D (A

(0.3)
DA DG +24V 24G X0 X2 X4 X6 X8 XA XC XE COM

7.5
pp
(1.97)

DB SLD (FG) X1 X3 X5 X7 X9 XB XD XF COM ro

50

x.
10 DIN rail
5 center
) 7.9
(0.31)
(0.16)

2 (0.08)
4

11
(When the protective cover attached.) (0.43)

STATION NO. B RATE

X0 1 2 3 4 5 6 7 X8 9 A B C D E F 40 20 10 8 4 2 1 4 2 1

ON

AJ65SBTB1-16D
DA DG +24V 24G X0 X2 X4 X6 X8 XA XC XE COM
DB SLD (FG) X1 X3 X5 X7 X9 XB XD XF COM
(2.44)
62

(1.36)
34.5

PULL
A6CVR-16

118 (4.65) 4 38.5

A 90 (3.54)
(0.16) (1.52)

52.5
46 (1.81)
(2.07)

Unit: mm (inch)

App - 2 App - 2
APPENDICES
MELSEC-A

Remark
For AJ65SBTB1-16D, AJ65SBTB1-16T Remote I/O Module of hardware version D
or before, side face diagram of the module is as follows.

20
(0.79)

(0.43)
11
(A
pp
ro

(0.3)
x.

7.5
11
0)
DIN rail center
7.9
(0.31)

App - 3 App - 3
APPENDICES
MELSEC-A

Appendix 1.3 AJ65SBTW4-16 remote I/O module

The external dimensions for the AJ65SBTW4-16 remote I/O module are shown
below.

184.7 (7.27)
180 +10 (7.09 +0.04 ) (Mounting pitch)
2.1 0 2.6
(0.08) (0.10)
2-4.5 5.1 mounting holes (M4 screw)

(2.36)
60
(1.18)
30

(0.47)
12
(1.00)
25.5

2.1 180 +10 (7.09 +0.04

0 ) (Mounting pitch) 2.6
(0.08) 2-4.5 5.1 mounting holes (M4 screw) (0.10)

LINK CABL IN POWER CABL PW L RUN

L ERR.
X0 Y8
X1 Y9
57.9 (2.28)
4.5 (0.18)

X2 YA
X3 YB
CON1 CON3 CON5 CON7 X4 YC
LINK CABL OUT POWER CABL X5 YD
CON2 CON4 CON6 CON8
X6 YE
X7 YF

STATION NO.

MITSUBISHI AJ65SBTW4-16DT

Unit : mm (inch)

App - 4 App - 4
APPENDICES
MELSEC-A

Appendix 1.4 AJ65SBTB1-32 remote I/O module

The external dimensions for the AJ65SBTB1-32 remote I/O module are shown
below.
(1.57)
40

179 (7.05)
+1 +0.04
170 0 (6.7 0 ) (Mounting pitch)
2-4.5 5.1 mounting holes (M4 screw)
(0.65)

PW L RUN L ERR. X0 1 2 3 4 5 6 7 X8 9 A B C D E F X10 11 12 13 14 15 16 17 X18 19 1A1B 1C1D1E 1F STATION NO. B RATE

(1.97) 16.5

40 20 10 8 4 2 1 4 2 1

ON

(A
AJ65SBTB1-32D

(0.3)
pp

7.5
DA DG +24V 24G X0 X2 X4 X6 X8 XA XC XE X10 X12 X14 X16 X18 X1A X1C X1E COM
50

ro
DB SLD (FG) X1 X3 X5 X7 X9 XB XD XF X11 X13 X15 X17 X19 X1B X1D X1F COM

x.
DIN rail

10
7.9 center

5
)
(0.31)
(0.16)

89 (3.5)
4

2 (0.08)

(When the protective cover attached.) 11

(0.43)
PW L RUN L ERR. X0 1 2 3 4 5 6 7 X8 9 A B C D E F X10 11 12 13 14 15 16 17 X18 19 1A1B 1C1D1E 1F STATION NO. B RATE
40 20 10 8 4 2 1 4 2 1

ON

AJ65SBTB1-32D
DA DG +24V 24G X0 X2 X4 X6 X8 XA XC XE X10 X12 X14 X16 X18 X1A X1C X1E COM
DB SLD (FG) X1 X3 X5 X7 X9 XB XD XF X11 X13 X15 X17 X19 X1B X1D X1F COM
(2.44)
62

34.5 (1.36)

PULL

A6CVR-32

4 38.5 (1.52)
179 (7.05) (0.16) 52.5 (2.07)
151 (5.94)
76.5 (3.01)

Unit: mm (inch)

App - 5 App - 5
APPENDICES
MELSEC-A

Remark
For AJ65SBTB1-32D, AJ65SBTB1-32T Remote I/O Module of hardware version D
or before, side face diagram of the module is as follows.

20
(0.79)

(0.43)
11
(A
p
pr
ox

(0.3)
7.5
.1
10
DIN rail center
)

7.9
(0.31)

App - 6 App - 6
APPENDICES
MELSEC-A

Appendix 1.5 AJ65SBTC1-32 , and AJ65SBTC4-16 remote I/O module

The external dimensions for the AJ65SBTC1-32 , and AJ65SBTC4-16 remote I/O
modules are shown below.
(1.57)
40

118 (4.65)
+1 +0.04
109 0 (4.29 0 ) (Mounting pitch)
2-4.5 5.1 mounting holes (M4 screw)

STATION NO. B RATE

(0.65)

X0 1 2 3 4 5 6 7 X8 9 A B C D E F
16.5

40 20 10 8 4 2 1 4 2 1 ON

A J65SBTC4-16DN
(A
pp

(0.3)
7.5
(1.97)

DA DG +24V 24G X0 X1 X2 X3 X4 X5 X6 X7 COM ro

50

DB SLD (FG) Y8 Y9 YA YB YC YD YE YF COM

x.
+24V +24V +24V +24V +24V +24V +24V +24V 10
24G 24G 24G 24G 24G 24G 24G 24G
5
) DIN rail center
7.9
(0.31)
(0.16)
4

2 (0.08)

11
(When the protective cover attached.)
(0.43)
STATION NO. B RATE
X0 1 2 3 4 5 6 7 X8 9 A B C D E F
40 20 10 8 4 2 1 4 2 1 ON

A J65SBTC4-16DN
DA DG +24V 24G X0 X1 X2 X3 X4 X5 X6 X7 COM
DB SLD (FG) Y8 Y9 YA YB YC YD YE YF COM
+24V +24V +24V +24V +24V +24V +24V +24V
(2.44)

24G 24G 24G 24G 24G 24G 24G 24G

62

(1.36)
34.5

PULL
A6CVR-16

118 (4.65) 4 38.5 (1.52)

90 (3.54) (0.16)
46 (1.81)
52.5 (2.07)

Unit: mm (inch)

App - 7 App - 7
APPENDICES
MELSEC-A

Remark
(1) For the AJ65SBTC4-16D remote I/O module, the side view of the module is
shown below.

20
(0.79)

(0.43)
11
(A
pp
ro
x.

(0.3)
7.5
11
0
)

DIN rail center

7.9
(0.31)

(2) For the modules given in the following table, the side view is shown below.

Model Hardware Version

AJ65SBTC1-32D N or before
AJ65SBTC1-32D1 N or before
AJ65SBTC1-32T Q or before
AJ65SBTC1-32T1 E or before
AJ65SBTC1-32DT Q or before
AJ65SBTC1-32DT1 Q or before
AJ65SBTC1-32DT2 D or before
AJ65SBTC1-32DT3 D or before
AJ65SBTC4-16DT J or before
AJ65SBTC4-16DT2 C or before

20
(0.79)
(0.43)
11
(A
pp
ro
x.

(0.30)
11

7.5
0 )

DIN rail center

7.9
(0.31)

App - 8 App - 8
APPENDICES
MELSEC-A

Appendix 1.6 AJ65SBTCF1-32 remote I/O module

The external dimensions for the AJ65SBTCF1-32 remote I/O module are shown
below.
(1.57)
40

118 (4.64)
+1 +0.04
109 0 (4.29 0 ) (Mounting pitch)
2-4.5 5.1 mounting holes (M4 screw)
(0.65)

STATION NO. B RATE

X0 1 2 3 4 5 6 7 X8 9 A B C D E F 40 20 10 8 4 2 1 4 2 1
16.5

X0-XF ON
(A
X10 11121314151617 X18191A1B1C1D1E1F
pp
A J65SBTCF1-32D X10-X1F

(0.3)
7.5
ro
DA DG 24V 24G X10 X11 X12 X13 X14 X15 X16 X17 X18 X19 X1A X1B X1C X1D X1E X1F NC NC NC NC
x.
(1.57)

DB SLD (FG) X0 X1 X2 X3 X4 X5 X6 X7 X8 X9 XA XB XC XD XE XF NC NC COM COM

50

10

DIN rail center

5
)

7.9
14 (0.55)
(0.31)
or less
(0.16)

46 (1.81)
4

Unit : mm (inch)

Remark
For the modules given in the following table, the side view is shown below.

Model Hardware Version

AJ65SBTCF1-32D F or before
AJ65SBTCF1-32T F or before
AJ65SBTCF1-32DT F or before

20
(0.79)
(0.43)
11
(A
p pr
ox
.1

(0.30)
7.5
10
)

DIN rail center

7.9
(0.31)

App - 9 App - 9
APPENDICES
MELSEC-A

Appendix 1.7 AJ65SBTB2-8 , AJ65SBTB3-8 , and AJ65SBTB32-8 remote I/O module

The external dimensions for the AJ65SBTB2-8 , AJ65SBTB3-8 , and

AJ65SBTB32-8 remote I/O modules are shown below.
(1.57)
40

118 (4.65)
+1 +0.04
109 0 (4.29 0 ) (Mounting pitch)

2-4.5 5.1 mounting holes (M4 screw)

STATION NO. B RATE

(0.65)

Y0 1 2 3 4 5 6 7 40 20 10 8 4 2 1 4 2 1
16.5

ON

AJ65SBTB2-8T

(0.3)
(A

7.5
DA DG +24V 24G Y0 Y1 Y2 Y3 Y4 Y5 Y6 Y7 DC24V
50 (1.97)

pp
DB SLD (FG) COM COM COM COM COM COM COM COM DC24G
ro
x.
DIN rail
10

7.9
5
)

(0.31)
4 (0.16)

2 (0.08)

11
(When the protective cover attached.) (0.43)
STATION NO. B RATE
Y0 1 2 3 4 5 6 7 40 20 10 8 4 2 1 4 2 1

ON

AJ65SBTB2-8T
DA DG +24V 24G Y0 Y1 Y2 Y3 Y4 Y5 Y6 Y7 DC24V

DB SLD (FG) COM COM COM COM COM COM COM COM DC24G
(2.44)
62

(1.36)
34.5

PULL
A6CVR-16

118 (4.65) 4 38.5 (1.52)

90 (3.54) (0.16)
52.5 (2.07)
46 (1.81)

Unit: mm (inch)

App - 10 App - 10
APPENDICES
MELSEC-A

Appendix 1.8 AJ65SBTB1B-16 , AJ65SBTB2-16 , AJ65SBTB3-16 , and

AJ65SBTB32-16 remote I/O module

The external dimensions for the AJ65SBTB1B-16 , AJ65SBTB2-16 , AJ65SBTB3-

16 , and AJ65SBTB32-16 remote I/O modules are shown below.
(1.57)
40

179 (7.05)
+1 +0.04
107 0 (4.2 0 ) (Mounting pitch)
2-4.5 5.1 mounting holes (M4 screw)
PW L RUN L ERR. Y0 1 2 3 4 5 6 7 Y8 9 A B C D E F STATION NO. B RATE
40 20 10 8 4 2 1 4 2 1
(0.65)
16.5

ON

(A
AJ65SBTB2-16T

(0.3)
p

7.5
DA DG +24V 24G Y0 Y1 Y2 Y3 Y4 Y5 Y6 Y7 Y8 Y9 YA YB YC YD YE YF

pr
DC24V
(1.97)

DB SLD (FG) COM COM COM COM COM COM COM COM COM COM COM COM COM COM COM COM

ox
DC24G
50

DIN rail center

.1
05
7.9

)
(0.31)
4 (0.16)

2 (0.08)
89 (3.5)
(When the protective cover attached.) 11
(0.43)
PW L RUN L ERR. Y0 1 2 3 4 5 6 7 Y8 9 A B C D E F STATION NO. B RATE
40 20 10 8 4 2 1 4 2 1

ON

AJ65SBTB2-16T
DA DG +24V 24G Y0 Y1 Y2 Y3 Y4 Y5 Y6 Y7 Y8 Y9 YA YB YC YD YE YF DC24V
(2.44)

DB SLD (FG) COM COM COM COM COM COM COM COM COM COM COM COM COM COM COM COM DC24G
62

(1.36)
34.5

PULL

A6CVR-32

4 38.5 (1.52)
179 (7.05) (0.16)
52.5 (2.07)
151 (5.94)
76.5 (3.01)

Unit: mm (inch)

App - 11 App - 11
APPENDICES
MELSEC-A

Appendix 1.9 AJ65SBTB2N-8 remote I/O module

The external dimensions for the AJ65SBTB2N-8 remote I/O module are shown
below.
(1.57)
40

118 (4.65)
+1 +0.04
109 0 (4.29 0 ) (Mounting pitch)

2-4.5 5.1 mounting holes (M4 screw)

STATION NO. B RATE X0 1 2 3 4 5 6 7

(0.65)

40 20 10 8 4 2 1 4 2 1
AJ65SBTB2N-8A
16.5

ON
(A

(0.3)
7.5
DA DG +24V 24G X0 X1 X2 X3 X4 X5 X6 X7 COMA
pp
50 (1.97)

DB SLD (FG) COMB COMB COMB COMB COMB COMB COMB COMB COMB
ro
x.

DIN rail center

10
5

7.9
)

(0.31)
4 (0.16)

2 (0.08)

11
(When the protective cover attached.) (0.43)

MITSUBISHI STATION NO. B RATE PW L RUN L ERR X0 1 2 3 4 5 6 7

AJ65SBTB2N-8A 40 20 10 8 4 2 1 4 2 1
ON

DA DG +24V 24G
X0 X1 X2 X3 X4 X5 X6 X7 COM A
DB SLD (FG)
(2.44)

COM B COM B COM B COM B COM B COM B COM B COM B COM B

62

(1.36)
34.5

PULL
A6CVR-16

118 (4.65) 4 38.5 (1.52)

(0.16)
90 (3.54)
52.5 (2.07)
46 (1.81)

Unit: mm (inch)

App - 12 App - 12
APPENDICES
MELSEC-A

Appendix 1.10 AJ65SBTB2N-16 remote I/O module

The external dimensions for the AJ65SBTB2N-16 remote I/O module are shown
below.
(1.57)
40

179 (7.05)
+1 +0.04
107 0 (4.2 0 ) (Mounting pitch)
2-4.5 5.1 mounting holes (M4 screw)
STATION NO. B RATE PW L RUN L ERR. X0 1 2 3 4 5 6 7 X8 9 A B C D E F
40 20 10 8 4 2 1 4 2 1
(0.65)

AJ65SBTB2N-16A
(1.97) 16.5

ON

(0.3)
7.5
DA DG +24V 24G X0 X1 X2 X3 X4 X5 X6 X7 X8 X9 XA XB XC XD XE XF COMA

(A
DB SLD (FG) COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB

pp
50

DIN rail center

ro
x.
7.9

10
(0.31)

5
)
4 (0.16)

89 (3.5) 2 (0.08)
11
(When the protective cover attached.) (0.43)
STATION NO. B RATE PW L RUN L ERR. X0 1 2 3 4 5 6 7 X8 9 A B C D E F
40 20 10 8 4 2 1 4 2 1
AJ65SBTB2N-16A
ON

DA DG +24V 24G X0 X1 X2 X3 X4 X5 X6 X7 X8 X9 XA XB XC XD XE XF COMA

DB SLD (FG) COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB COMB
(2.44)
62

(1.36)
34.5

PULL

A6CVR-32

4 38.5 (1.52)
179 (7.05) (0.16)
52.5 (2.07)
151 (5.94)
76.5 (3.01)

Unit: mm (inch)

App - 13 App - 13
APPENDICES
MELSEC-A

Appendix 1.11 AJ65VBTCU -8 , AJ65VBTCU -16 , and AJ65VBTCF1-32 remote I/O

module

The external dimensions for the AJ65VBTCU -8 , AJ65VBTCU -16 , and

AJ65VBTCF1-32 remote I/O modules are shown below.

AJ65VBTCU -8

40S
20T
A
10T
8 I
4 O
N
2N
1 O
4 B
B
2 A
T
1 E

41(1.61) 31(1.22) * 62(2.44) 3.5(0.14)

16.5
(0.65)

AJ65VBTCU3-8D1
CON L
A I
N
CON K
B 57.5(2.26)

X0 PW
L RUN
X1
L ERR

X2
0
115(4.53)

1 DIN
X3 2 rail
3
4
X4 5
6
X5 7

X6
57.5(2.26)

X7

P
CON W
C /
A
U
CON X
D

Unit: mm (inch)
: This section should be 14.5mm (0.57 inches) when an online connector is not installed.

App - 14 App - 14
APPENDICES
MELSEC-A

AJ65VBTCU -16

40 S
20 T
A
10 T
8 I
4 O
N
2 N
1 O
4 B
B
2 A
T
1 E

60(2.36) 31(1.22) * 62(2.44) 3.5(0.14)

16.5
(0.65)

AJ65VBTCU3-16D1
CON L
A I
N
CON K
B

57.5(2.26)
PW
L RUN

L ERR

0
1 DIN
2
115(4.53)

rail
3
4
5
6
7

8
9
A
B
C
57.5(2.26)

D
E
X0 to X7 X8 to XF F

CON P
C W
/
A
CON U
D X

Unit: mm (inch)
: This section should be 14.5mm (0.57 inches) when an online connector is not installed.

App - 15 App - 15
APPENDICES
MELSEC-A

AJ65VBTCF 1-32

41(1.61) 46(1.81)* 63.5(2.50)

4(0.16)

57.5(2.27)
DIN
115 (4.53)

rail

57.5(2.27)

16.5
(0.65)
2(0.08)

31(1.22) 67(2.64)

Unit: mm (inch)
: This section should be 14.5mm (0.57 inches) when an online connector is not installed.

App - 16 App - 16
APPENDICES
MELSEC-A

Appendix 1.12 AJ65FBTA -16 remote I/O module

The external dimensions for the AJ65FBTA -16 remote I/O modules are shown
below.

AJ65FBTA -16
2-4.5 6 mounting screw
+1 +0.04
60 0 2.36 0
48(1.89)
50 1 (1.97 0.04)
34 0.5

(0.17)
26.5

4.3
18.3 (1.34 0.02)
(0.72) (1.04) 6(0.24)
(0.84)
21.3
68(2.68)
+0.04

192 1(7.56 0.04)

7.87 0
+1
200 0

24(0.94)

33(1.30)
25(0.98)
25(0.98)
25(0.98)

Storage sheet

6(0.24)

4.1 21.7
(0.16) 35 M4 mounting screw (0.85)
32
(1.38) (1.26)
Unit: mm (inch)

App - 17 App - 17
APPENDICES
MELSEC-A

Appendix 1.13 AJ65VBTS -16 , and AJ65VBTS -32 remote I/O module

The external dimensions of the AJ65VBTS -16 , and AJ65VBTS -32 remote I/O
modules are shown below.

AJ65VBTS -16
2-M4 mounting holes
137 (5.39)
15.5

(0.53)
13.5
106 0.5 (4.17 0.02) (0.61) 5.0

(0.47)
(0.20)

12
ONPW
B RATE STATION NO.

L RUN L ERR.

(0.91)
1 2 4 1 2 4 8 1020 40

AJ65VBTS3-16D

(1.02 0.01)
0 1 2 3 4 5 6 7

23

(2.52 0.01)
8 9 A B C D E F

26 0.3

64 0.3
NC X0 X1 X2 X3 X4 X5 X6 X7 X8 X9 XA XB XC XD XE XF

(1.97)
50

(1.65)
DIN rail center

42
COM+ COM+

4
COM- COM-
(0.16)
CON A B C D

(0.18)
4.5 51.5

(0.53)
13.5
(2.03)
(1.22)
31

(0.65)
16.5
(1.24)
31.5

(0.20)
5

13.5 13.5
151 0.5 (5.94 0.02)
(0.53) (0.53)

Unit: mm (inch)
: This section should be 145mm (0.57 inches) when an online connector is not installed.

App - 18 App - 18
APPENDICES
MELSEC-A

AJ65VBTS -32
13.5 222 13.5 2-M4 mounting holes
(0.53) (8.74) (0.53)

(1.02 0.01) (0.47)

12
ON
B RATESTATION NO.

PW L RUN
L ERR.

(0.91)
1 2 4 1 2 4 8 102040

AJ65VBTS3-32D
0 1 2 3 4 5 6 7

23
50 (1.97)
8 9 A B CD E F

26 0.3
NC X0 X1 X2 X3 X4 X5 X6 X7 X8 X9 XA XB XC XD XE XF NC X10 X11 X12 X13 X14 X15 X16 X17 X18 X19 X1A X1B X1C X1D X1E X1F

(1.65)
42
DIN rail center
COM1+ COM1+ COM2+ COM2+

COM1- COM1- COM2- COM2-

CON A B C D

4
236 0.5 51.5 (0.16)
(9.29 0.02) (2.03)
(1.22)
31

(0.65)
16.5
(1.24)
31.5

(0.20)
5
Unit: mm (inch)
: This section should be 14.5mm (0.57 inches) when an online connector is not installed.

App - 19 App - 19
APPENDICES
MELSEC-A

Appendix 1.14 AJ65VBTCE -8 , AJ65VBTCE -16 , and AJ65VBTCE -32 remote I/O
module

The external dimensions of the AJ65VBTCE -8 , AJ65VBTCE -16 , and

AJ65VBTCE -32 remote I/O modules are shown below.

AJ65VBTCE -8
54 0.3
(2.13 0.01)
40.5 (1.59)

13.5 13.5
(0.53) (0.53)

31 30.5
(1.22) (1.20)

(0.53)
13.5
40 16.5 26
(1.57) (0.65) (1.02)

CON ON
1
2
A 3
4
5
6
7

(1.63)
8
9

41.5
B 10

40 S
T
20 A
C 10 T
I
8 O
4 N
2 N
1 O.
(3.27 0.02)

D 4 B

(4.49 0.02)
R
2 A
T
1

114 0.5
E
83 0.5

AJ65VBTCE3-8D
PW
X0 L RUN
(3.94)
100

L ERR.
X1
0
1
X2 2
3
X3 4
5
6
X4 7

X5

X6
DIN rail center
X7
(0.16)
4

(0.53)
13.5

2-M4 mounting holes 5

10 (0.20)
(0.39)
40.5 (1.59)
43.5 (1.71)

Unit: mm (inch)
: This section should be 14.5mm (0.57 inches) when an online connector is not installed.

App - 20 App - 20
APPENDICES
MELSEC-A

AJ65VBTCE -8
(When the protective cover attached.)
29
(1.14)

(2.03)
51.5
(0.81)
20.5

89 (3.50)

CON ON

B
40 S
T
20 A
10 T
I
C 8 O
4 N
2 N
1 O.
.
4 B
R
D 2 A
T
1 E

AJ65VBTCE3- 8D
PW

(4.07)
103.5
X0 L RUN

L ERR.
X1
0
1
X2 2
3
X3 4
5
6
X4 7

X5

X6
>PC<

X7

40.5
43.5 (1.71) (1.59)
(1.52)
38.5

29
(1.14)

Unit: mm (inch)

App - 21 App - 21
APPENDICES
MELSEC-A

AJ65VBTCE -16
100 2-M4 mounting holes
(3.94) 8.5 5.0

(0.53)
13.5
(0.33) (0.20)
83 0.5

(0.33)
(3.27 0.02)

8.5
ON
PW L RUNL ERR. AJ65VBTCE3-16D
1 2 4 1 2 4 8 102040
B RATE STATION NO.

(0.93)
23.5
0 1 2 3 4 5 6 7

(1.30 0.01)

(2.52 0.01)
8 9 A B C D E F

33 0.3

64 0.3
(1.97)
50
X 0 1 2 3 4 5 6 7
DIN rail center
4
(0.16)
CON A B C D X 8 9 A B C D E F

(0.18)
4.5
(0.16) 41.5

(0.53)
13.5
(1.63)
DIN rail center 45.5
(1.22)

(1.79)
31

(0.65)
16.5
(1.24)
31.5

(0.20)
5

13.5 41.5 13.5

(0.53) (1.63) (0.53)
114 0.5
(4.49 0.02)

Unit: mm (inch)
: This section should be 14.5mm (0.57 inches) when an online connector is not installed.

App - 22 App - 22
APPENDICES
MELSEC-A

AJ65VBTCE -16
(When the protective cover attached.)
29
(1.14)

(2.03)
51.5
(0.81)
20.5

90
(3.54)
CON A

1 2 4 1 2 4 8 102040
B RATESTATION NO.
ON
B

PWL RUNL ERR.

8 9 A B C DE F

0 1 2 3 4 5 6 7
C
D

(4.09)
104
Y

X
8

0
9

1
A

2
3
B

AJ65VBTCE32-16DT
C

4
D

>PC<
6
E

7
F

41.5
54 (2.13) (1.63)
(1.48)
37.5

39
(1.54)

Unit: mm (inch)

App - 23 App - 23
APPENDICES
MELSEC-A

AJ65VBTCE -32
2-M4 mounting holes

(0.53)
13.5 155 (6.10) 13.5 5.0

13.5
(0.53) 129 0.5 (5.08 0.02) (0.53) (0.20)

(0.33)
8.5
AJ65VBTCE3-32D

(0.93)
(1.02 0.01)

23.5

(2.52 0.01)
26 0.3

(1.97)

64 0.3
50
4
(0.16)

(0.18)
4

4.5
41.5 (1.63) DIN rail center
(0.16)

(0.53)
13.5
169 0.5 45.5 (1.79)
(6.65 0.02)

DIN rail center

(1.22)
31 *

(0.65)
16.5
(1.24)

(0.20)
31.5

72.5
(2.85)

Unit: mm (inch)
: This section should be 14.5mm (0.57 inches) when an online connector is not installed.

App - 24 App - 24
APPENDICES
MELSEC-A

Appendix 1.15 AJ65DBTB1-32 remote I/O module

The external dimensions of the AJ65DBTB1-32 remote I/O modules are shown
below.

Unit: mm (inch)

App - 25 App - 25
APPENDICES
MELSEC-A

Appendix 1.16 AJ65SBTB1-32K , AJ65SBTB3-16KD, and AJ65SBTB32-16K remote I/O

module

The external dimensions of the AJ65SBTB1-32K , AJ65SBTB3-16KD, and

AJ65SBTB32-16K remote I/O modules are shown below.

(1.57)
40
179 (7.05)
170 (6.70 ) (Mounting pitch)
2-4.5 5.1 mounting holes (M4 screw)
7.9
(0.31)

(0.65)
16.5

(A
pp
ro
(1.97)

x.
50

10

(0.3)
5

7.5
)
(0.16)

(DIN rail center)

4

89 (3.50)

Unit: mm (inch)

App - 26 App - 26
APPENDICES
MELSEC-A

MEMO

App - 27 App - 27
WARRANTY
Please confirm the following product warranty details before using this product.

1. Gratis Warranty Term and Gratis Warranty Range

If any faults or defects (hereinafter "Failure") found to be the responsibility of Mitsubishi occurs during use of the product
within the gratis warranty term, the product shall be repaired at no cost via the sales representative or Mitsubishi Service
Company.
However, if repairs are required onsite at domestic or overseas location, expenses to send an engineer will be solely at
the customer’s discretion. Mitsubishi shall not be held responsible for any re-commissioning, maintenance, or testing
on-site that involves replacement of the failed module.
[Gratis Warranty Term]
The gratis warranty term of the product shall be for one year after the date of purchase or delivery to a designated place.
Note that after manufacture and shipment from Mitsubishi, the maximum distribution period shall be six (6) months, and
the longest gratis warranty term after manufacturing shall be eighteen (18) months. The gratis warranty term of repair
parts shall not exceed the gratis warranty term before repairs.
[Gratis Warranty Range]
(1) The range shall be limited to normal use within the usage state, usage methods and usage environment, etc., which
follow the conditions and precautions, etc., given in the instruction manual, user's manual and caution labels on the
product.
(2) Even within the gratis warranty term, repairs shall be charged for in the following cases.
1. Failure occurring from inappropriate storage or handling, carelessness or negligence by the user. Failure caused
by the user's hardware or software design.
2. Failure caused by unapproved modifications, etc., to the product by the user.
3. When the Mitsubishi product is assembled into a user's device, Failure that could have been avoided if functions
or structures, judged as necessary in the legal safety measures the user's device is subject to or as necessary by
industry standards, had been provided.
4. Failure that could have been avoided if consumable parts (battery, backlight, fuse, etc.) designated in the
instruction manual had been correctly serviced or replaced.
5. Failure caused by external irresistible forces such as fires or abnormal voltages, and Failure caused by force
majeure such as earthquakes, lightning, wind and water damage.
6. Failure caused by reasons unpredictable by scientific technology standards at time of shipment from Mitsubishi.
7. Any other failure found not to be the responsibility of Mitsubishi or that admitted not to be so by the user.

2. Onerous repair term after discontinuation of production

(1) Mitsubishi shall accept onerous product repairs for seven (7) years after production of the product is discontinued.
Discontinuation of production shall be notified with Mitsubishi Technical Bulletins, etc.
(2) Product supply (including repair parts) is not available after production is discontinued.

3. Overseas service
Overseas, repairs shall be accepted by Mitsubishi's local overseas FA Center. Note that the repair conditions at each FA
Center may differ.

4. Exclusion of loss in opportunity and secondary loss from warranty liability

Regardless of the gratis warranty term, Mitsubishi shall not be liable for compensation of damages caused by any cause
found not to be the responsibility of Mitsubishi, loss in opportunity, lost profits incurred to the user by Failures of
Mitsubishi products, special damages and secondary damages whether foreseeable or not, compensation for accidents,
and compensation for damages to products other than Mitsubishi products, replacement by the user, maintenance of on-
site equipment, start-up test run and other tasks.

5. Changes in product specifications

The specifications given in the catalogs, manuals or technical documents are subject to change without prior notice.

SH(NA)-4007-AA