Sony Hcd-Shake10 30 Hcdshakex10!30!70 Ver.1.0 SM

HCD-SHAKE10/SHAKE30/
HCDSHAKEX10/HCDSHAKEX30/HCDSHAKEX70
SERVICE MANUAL US Model
Canadian Model
Ver. 1.0 2017.03 HCD-SHAKE10/SHAKE30
AEP Model
HCDSHAKEX30/HCDSHAKEX70
UK Model
HCDSHAKEX30
E Model
HCDSHAKEX10/HCDSHAKEX30/
HCDSHAKEX70
Photo: HCDSHAKEX70 Australian Model

HCDSHAKEX10/HCDSHAKEX30
• HCD-SHAKE10 is the tuner, USB, CD Player, Bluetooth, NFC and amplifier section in SHAKE-X10.
• HCD-SHAKE30 is the tuner, USB, CD Player, Bluetooth, NFC and amplifier section in SHAKE-X30.
• HCDSHAKEX10 is the tuner, USB, DVD Player, Bluetooth, NFC and amplifier section in SHAKE-X10D.
Note:
Be sure to keep your PC used for service and
checking of this unit always updated with the
latest version of your anti-virus software.
In case a virus affected unit was found during
service, contact your Service Headquarters.
Model Name Using Similar Mechanism HCD-SHAKEX1/SHAKEX3/SHAKEX7

CD/DVD Section CD/DVD Mechanism Type CDM90-DVBU204//M
Optical Pick-up Name CMS-S76RFS7GP OR CMS-S76RFS7G1
SPECIFICATIONS
AUDIO POWER SPECIFICATIONS MIC2/GUITAR: Laser Diode Properties BLUETOOTH section
Sensitivity 1 mV, impedance Emission Duration: Continuous Communication system:
POWER OUTPUT AND TOTAL 10 kilohms (When guitar mode is Laser Output*: Less than 44.6 μW BLUETOOTH Standard version 3.0
HARMONIC DISTORTION: turned off.) * This output is the value measurement Output:
(US models only) Sensitivity 200 mV, impedance at a distance of 200 mm from the BLUETOOTH Standard Power Class 2
Shake-X30 only 1 Megaohm (When guitar mode is objective lens surface on the Optical Maximum communication range:
With 4 ohm loads, both channels driven, from turned on.) Pick-up Block with 7 mm aperture. Line of sight approx. 10 m (33 ft)*1
150 Hz – 20,000 Hz; rated 90 watts per channel Outputs Frequency response: Frequency band:
minimum RMS power, with no more than 0.7% 20 Hz – 20 kHz 2.4 GHz band (2.4000 GHz –
total harmonic distortion from 250 milliwatts to AUDIO/PARTY CHAIN OUT L/R:
Voltage 2 V, impedance 1 kilohm Video color system format (SHAKE-X10D/ 2.4835 GHz)
rated output. X30D/X70D): Modulation method:
VIDEO OUT (SHAKE-X10D/X30D/X70D):
Shake-X10 only Max. output level 1 Vp-p, LA9 model: FHSS (Freq Hopping Spread Spectrum)
With 4 ohm loads, both channels driven, from NTSC Compatible BLUETOOTH profiles*2:
unbalanced, Sync. negative load
150 Hz – 20,000 Hz; rated 80 watts per channel Other models: A2DP (Advanced Audio Distribution
minimum RMS power, with no more than 0.7% impedance 75 ohms
HDMI OUT (TV) (SHAKE-X10D/X30D/ NTSC and PAL Profile)
total harmonic distortion from 250 milliwatts to
X70D): USB section AVRCP (Audio Video Remote Control
rated output.
Supported audio signal: Supported USB device: Profile)
Inputs Mass Storage Class SPP (Serial Port Profile)
2-channel Linear PCM (up to
AUDIO/PARTY CHAIN IN L/R Maximum current: Supported codecs:
48 kHz), Dolby Digital
(SHAKE-X10/X30): 1A SBC (Subband Codec)
Voltage 2 V, impedance HDMI section (SHAKE-X10D/X30D/X70D) AAC (Advanced Audio Coding)
Connector: (USB) port:
47 kilohms Type A LDAC
AUDIO/PARTY CHAIN IN (TV) L/R Type A (19 pin) *1
The actual range will vary depending on
(SHAKE-X10D/X30D/X70D): Disc player section FM tuner section factors such as obstacles between devices,
Voltage 2 V, impedance System: FM stereo, FM superheterodyne tuner magnetic fields around a microwave oven,
47 kilohms Compact disc and digital audio system Antenna: static electricity, reception sensitivity,
TV (ARC) (SHAKE-X10D/X30D/X70D): (SHAKE-X10/X30) FM lead antenna antenna’s performance, operating system,
Supported audio signal: Compact disc and digital audio and Tuning range: software application, etc.
2-channel Linear PCM video system (SHAKE-X10D/X30D/ 87.5 MHz – 108.0 MHz (100 kHz step) *2
BLUETOOTH standard profiles indicate the
MIC1: X70D) (SHAKE-X10/X30) purpose of BLUETOOTH communication
Sensitivity 1 mV, impedance 87.5 MHz – 108.0 MHz (50 kHz step) between devices.
10 kilohms (SHAKE-X10D/X30D/X70D)
– Continued on next page –
CD/DVD RECEIVER
9-890-688-01
2017C80-1 Sony Corporation
© 2017.03 Published by Sony EMCS (Malaysia) PG Tec
HCD-SHAKE10/SHAKE30/HCDSHAKEX10/HCDSHAKEX30/HCDSHAKEX70
Supported audio formats License and Trademark Notice

Supported bit rate and sampling frequencies: • “CD” logo is trademark.
MP3: • is a trademark of DVD Format/Logo Licensing Corporation.
32/44.1/48 kHz,
32 kbps – 320 kbps (VBR) • “DVD+RW”, “DVD-RW”, “DVD+R”, “DVD-R”, “DVD VIDEO”,
AAC: and the “CD” logos are trademarks.
44.1 kHz, 48 kbps – 320 kbps • WALKMAN ® and WALKMAN ® logo are registered
(CBR/VBR) trademarks of Sony Corporation.
WMA:
• MPEG Layer-3 audio coding technology and patents licensed from
44.1 kHz, 48 kbps – 192 kbps
Fraunhofer IIS and Thomson.
(CBR/VBR)
WAV: • Windows Media is either a registered trademark or trademark of
44.1/48 kHz (16 bit) Microsoft Corporation in the United States and/or other countries.
Supported video formats (SHAKE-X10D/X30D/X70D) • This product is protected by certain intellectual property rights
Xvid: of Microsoft Corporation. Use or distribution of such technology
Video codec: Xvid video outside of this product is prohibited without a license from
Bit rate: 4.854 Mbps (MAX) Microsoft or an authorized Microsoft subsidiary.
Resolution/Frame rate:
• This system incorporates Dolby* Digital.
720 × 480, 30 fps
* Manufactured under license from Dolby Laboratories. Dolby,
720 × 576, 25 fps (except for LA9 model)
Audio codec: MP3 Dolby Audio, and the double-D symbol are trademarks of
MPEG4: Dolby Laboratories.
File format: MP4 File Format • This system incorporates High-Definition Multimedia In-
Video codec: MPEG4 Simple terface (HDMI™) technology. The terms HDMI and HDMI
Profile (AVC is not compatible.) High-Definition Multimedia Interface, and the HDMI Logo
Bit rate: 4 Mbps are trademarks or registered trademarks of HDMI Licens-
Resolution/Frame rate: ing, LLC in the United States and other countries.
720 × 480, 30 fps • “BRAVIA” is a trademark of Sony Corporation.
720 × 576, 25 fps (except for LA9 model)
Audio codec: AAC-LC (HE-AAC is not compatible.) • LDAC™ and LDAC logo are trademarks of Sony
DRM: Not compatible Corporation.
General • The BLUETOOTH® word mark and logos are registered
Power requirements: trademarks owned by Bluetooth SIG, Inc. and any use of such
SHAKE-X10/X30: AC 120 V, 60 Hz marks by Sony Corporation is under license. Other trademarks and
SHAKE-X10D/X30D/X70D: AC 120 V – 240 V, 50/60 Hz trade names are those of their respective owners.
Power consumption: • The N-Mark is a trademark or registered trademark of NFC
SHAKE-X70D: 375 W Forum, Inc. in the United States and in other countries.
SHAKE-X30D/SHAKE-X10D/SHAKE-X30/SHAKE-X10:
• Android™ is a trademark of Google Inc.
220 W
Power consumption (at the Power Saving mode) (SHAKE-X10D/ • Google Play is a trademark of Google Inc.
X30D/X70D): • Apple, the Apple logo, iPhone, and iPod touch are trademarks
0.5 W (When “BT STBY” is set to “OFF” and [CONTROL of Apple Inc., registered in the U.S. and other countries. App
FOR HDMI] is set to [OFF].) Store is a service mark of Apple Inc., registered in the U.S.
3 W* (When “BT STBY” is set to “ON” and [CONTROL and other countries.
FOR HDMI] is set to [ON].)
Dimensions (w/h/d) (excl. speakers) • “Made for iPod,” and “Made for iPhone” mean that an
(Approx.): electronic accessory has been designed to connect specifically
455 mm × 165 mm × 330 mm to iPod or iPhone, respectively, and has been certified by the
(18 in × 6 1/2 in × 13 in) developer to meet Apple performance standards. Apple is not
Mass (excl. speakers) (Approx.): responsible for the operation of this device or its compliance
SHAKE-X70D: 6.2 kg with safety and regulatory standards. Please note that the use
SHAKE-X30D/SHAKE-X10D/SHAKE-X30/SHAKE-X10: of this accessory with iPod or iPhone may affect wireless
5.8 kg (12 lb 13 oz) performance.
* The power consumption of the system will be less than 0.5 W • THIS PRODUCT IS LICENSED UNDER THE MPEG-4 VISUAL
when there is no HDMI connection and “BT STBY” is set to PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND
“OFF”. NON-COMMERCIAL USE OF A CONSUMER FOR
(i) ENCODING VIDEO IN COMPLIANCE WITH THE MPEG-
Design and specifications are subject to change without notice. 4 VISUAL STANDARD (“MPEG-4 VIDEO”)
AND/OR
(ii) DECODING MPEG-4 VIDEO THAT WAS ENCODED BY
A CONSUMER ENGAGED IN A PERSONAL AND NON-
COMMERCIAL ACTIVITY AND/OR WAS OBTAINED
FROM A VIDEO PROVIDER LICENSED TO PROVIDE
MPEG-4 VIDEO.
NO LICENSE IS GRANTED OR SHALL BE IMPLIED
FOR ANY OTHER USE. ADDITIONAL INFORMATION
INCLUDING THAT RELATING TO PROMOTIONAL,
INTERNAL AND COMMERCIAL USES AND LICENSING
MAY BE OBTAINED FROM MPEG LA, L.L.C.
HTTP://WWW.MPEGLA.COM
• All other trademarks are trademarks of their respective
owners.
• In this manual, ™ and ® marks are not specified.
SAFETY-RELATED COMPONENT WARNING!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE • Abbreviation

WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN AR : Argentina model
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. AUS : Australian model
REPLACE THESE COMPONENTS WITH SONY PARTS CND : Canadian model
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS E4 : African model
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. EA : Saudi Arabia model
LA9 : Latin-American model
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR

LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONC-
TIONNEMENT. NE REMPLACER CES COMPOSANTS QUE
PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DON-
NÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.
2
NOTES ON CHIP COMPONENT REPLACEMENT

• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
FLEXIBLE CIRCUIT BOARD REPAIRING

• Keep the temperature of the soldering iron around 270 °C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage. Check
leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2V AC range are suitable. (See
Fig. A)
To Exposed Metal
Parts on Set
AC
0.15 μF 1.5 kΩ voltmeter
(0.75 V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
3
TABLE OF CONTENTS
1. SERVICING NOTES ............................................. 5 6-15. Printed Wiring Board - LED DRIVER Board - .............. 48
6-16. Printed Wiring Board
2. DISASSEMBLY - SKY BLUE Board (SHAKE10/SHAKE30/
2-1. Disassembly Flow ........................................................... 10 HCDSHAKEX10/HCDSHAKEX30) - .......................... 49
2-2. Panel, Side (L), Panel, Side (R), Panel, Top Assy .......... 11 6-17. Printed Wiring Board
2-3. 2CH DAMP Board (SHAKE10/SHAKE30/ - BAR CENTER Board (HCDSHAKEX70) - ................ 49
HCDSHAKEX10/HCDSHAKEX30) ............................. 12 6-18. Printed Wiring Board
2-4. 4CH DAMP BOARD (HCDSHAKEX70) ..................... 13 - HI-RGB RIGHT LED PC BO Board (SHAKE10/
2-5. Back Panel Section (SHAKE10/SHAKE30/ SHAKE30/HCDSHAKEX10/HCDSHAKEX30) - ........ 50
HCDSHAKEX10/HCDSHAKEX30) ............................. 14 6-19. Printed Wiring Board
2-6. Back Panel Section (HCDSHAKEX70) ......................... 14 - HI-RGB RIGHT Board (HCDSHAKEX70) - .............. 50
2-7. Panel, Loading Assy ....................................................... 15 6-20. Printed Wiring Board - HI-RGB LEFT Board - ............. 51
2-8. CDM90-DVBU204//M ................................................... 16 6-21. Printed Wiring Board - IR Board -.................................. 51
2-9. Front Panel Section ......................................................... 17 6-22. Schematic Diagram - IR Board - .................................... 51
2-10. MOTHERBOARD Board ............................................... 17
2-11. REGULATOR, SWITCHING (SSN-172AD) 7. EXPLODED VIEWS
(SHAKE10/SHAKE30/HCDSHAKEX10/ 7-1. Panel, Side Section ......................................................... 53
HCDSHAKEX30) .......................................................... 18 7-2. 2CH DAMP, 4CH DAMP Board Section ....................... 54
2-12. REGULATOR, SWITCHING (SSN-171AD) 7-3. Back Panel Section ......................................................... 55
(HCDSHAKEX70) ......................................................... 19 7-4. MOTHERBOARD Board Section .................................. 56
2-13. Service, Optical Device (7G), Flexible Flat Cable ......... 20 7-5. Front Panel Section ......................................................... 57
7-6. Chassis Section ............................................................... 58
3. TEST MODE ............................................................ 21 7-7. Top Panel Section ........................................................... 59
7-8. CD/DVD Mechanism Section
4. ELECTRICAL CHECK ......................................... 23 (CDM90-DVBU204//M) ................................................ 60
5. TROUBLESHOOTING .......................................... 24 8. ELECTRICAL PARTS LIST .............................. 61
6. DIAGRAMS
6-1. Block Diagram
- RS SERVO, USB, HDMI Section - ............................. 33
6-2. Block Diagram - MAIN Section -................................... 34
6-3. Block Diagram - AMP Section - ..................................... 35
6-4. Block Diagram
- PANEL, POWER SUPPLY Section - ........................... 36
- MOTHERBOARD Board (Component Side) - ............ 38
- MOTHERBOARD Board (Conductor Side) - ............. 39
- 2CH DAMP Board (SHAKE10/SHAKE30/
HCDSHAKEX10/HCDSHAKEX30) - .......................... 40
- 4CH DAMP Board (Component Side)
(HCDSHAKEX70) - ....................................................... 41
- 4CH DAMP Board (Conductor Side)
(HCDSHAKEX70) - ....................................................... 42
6-10. Printed Wiring Board - TOP PANEL Board - ................. 43
6-11. Schematic Diagram - TOP PANEL Board - .................... 44
6-12. Printed Wiring Board - FL Board - ................................. 45
6-13. Printed Wiring Board - MIC Board - .............................. 46
6-14. Schematic Diagram - MIC Board - ................................. 47
4
SECTION 1
SERVICING NOTES
UNLEADED SOLDER MODEL IDENTIFICATION
Boards requiring use of unleaded solder are printed with the
leadfree mark (LF) indicating the solder contains no lead. - BACK PANEL -
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK L
Unleaded solder has the following characteristics.

• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
– MODEL LABEL –
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) DVD RECEIVER
MADE IN MALAYSIA
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc. SERIAL NO.
• Usable with ordinary solder PART No. Destination Code

It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
Model Part No.
CAUTION
HCDSHAKEX10: LA9 4-690-949-0[]
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation HCDSHAKEX30: LA9 4-690-949-1[]
exposure. HCDSHAKEX70: LA9 4-690-949-2[]
HCDSHAKEX10: AR 4-690-969-0[]
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK HCDSHAKEX30: AR 4-690-969-1[]
OR BASE UNIT HCDSHAKEX70: AR 4-690-969-2[]
HCD-SHAKE10 4-693-563-0[]
The laser diode in the optical pick-up block may suffer electrostatic HCD-SHAKE30 4-693-563-1[]
break-down because of the potential difference generated by the HCDSHAKEX10: E4 4-693-564-0[]
charged electrostatic load, etc. on clothing and the human body. HCDSHAKEX30: E4 4-693-564-1[]
During repair, pay attention to electrostatic break-down and also
HCDSHAKEX70: E4 4-693-564-2[]
use the procedure in the printed matter which is included in the
repair parts. AEP, UK 4-693-565-0[]
The flexible board is easily damaged and should be handled with HCDSHAKEX10: EA 4-693-566-0[]
care. HCDSHAKEX30: EA 4-693-566-1[]
HCDSHAKEX70: EA 4-693-566-2[]
NOTES ON LASER DIODE EMISSION CHECK
HCDSHAKEX10: AUS 4-694-735-0[]
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical HCDSHAKEX30: AUS 4-694-735-1[]
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens. • Abbreviation
AR : Argentina model
AUS : Australian model
CND : Canadian model
E4 : African model
EA : Saudi Arabia model
LA9 : Latin-American model
This appliance is classified as a CLASS 1 LASER product under
IEC 60825-1:2007. This marking is located on the rear exterior of
the unit.
5
PLAYABLE DISCS TEST DISCS

HCD-SHAKE10/SHAKE30: Use following TEST DISC when this unit confirms the operation
• AUDIO CD and checks it.
• CD-R/CD-RW in AUDIO CD format
• For CD
HCDSHAKEX10/HCDSHAKEX30/HCDSHAKEX70:
Part No. Description
• DVD VIDEO
3-702-101-01 DISC (YEDS-18), TEST
• DVD-R/DVD-RW in DVD VIDEO format or video mode
4-225-203-01 DISC (PATD-012), TEST
• DVD+R/DVD+RW in DVD VIDEO format
J-2501-307-A DISC (HLX-A1), TEST
• VIDEO CD (Ver. 1.0, 1.1, and 2.0 discs)
• Super VCD
• For DVD SL (Single Layer)
• CD-R/CD-RW/CD-ROM in VIDEO CD format or super VCD
Part No. Description
format
J-6090-069-A DISC (HLX-503), TEST (NTSC)
• AUDIO CD
• CD-R/CD-RW in AUDIO CD format
J-6090-077-A DISC (HLX-506), TEST (PAL)
PLAYABLE FILES ON DISCS
• Music: • For DVD DL (Double Layer)
MP3 files (.mp3)*1*2 Part No. Description
• Video (HCDSHAKEX10/HCDSHAKEX30/ J-6090-071-A DISC (HLX-501), TEST (NTSC)
HCDSHAKEX70): J-6090-089-A DISC (HLX-505), TEST (NTSC)
MPEG4 files (.mp4/.m4v)*2*3, Xvid files (.avi) J-2501-306-A DISC (HLX-514), TEST (NTSC)
J-6090-078-A DISC (HLX-507), TEST (PAL)
PLAYABLE FILES ON USB DEVICE
• Music: If “PROTECT XX” (X is a number)
MP3 files (.mp3)*1*2, WMA files (.wma)*2, AAC files appears on the display
(.m4a/.mp4/.3gp)*2, WAV files (.wav)*2 Immediately unplug the AC
• Video (HCDSHAKEX10/HCDSHAKEX30/ power cord (mains lead), and
HCDSHAKEX70): check the following items.
Ş Are you using only the supplied
MPEG4 files (.mp4/.m4v)*2*3, Xvid files (.avi)
speakers?
Note Ş Is anything blocking the
*1
MP3 (MPEG 1 Audio Layer 3) is a standard format defined by ventilation holes of the unit?
ISO/MPEG for compressed audio data. MP3 files must be in After you have checked and
MPEG 1 Audio Layer 3 format. found no problems, reconnect
the AC power cord (mains lead),
*2
Files with copyright protection (Digital Rights Management)
and turn on the system. If the
cannot be played back by the system. issue persists, contact your
*3
MPEG4 files must be recorded in MP4 file format. Supported nearest Sony dealer.
video codec and audio codec are as follows:
‒ Video codec: MPEG4 Simple Profile (AVC is not
supported.)
‒ Audio codec: AAC-LC (HE-AAC is not supported.)
*4
A logical format of files and folders on CD-ROMs, defined by
ISO (International Organization for Standardization).
NOTE OF REPLACEMENT OF THE MS-476 BOARD

When the MS-476 board is defective, exchange the entire
LOADING COMPLETE ASSY (T).
RELEASING THE DISC TRAY LOCK

The disc tray lock function for the antitheft of sample disc in the
shop is equipped.
It can release the lock function in the following procedure.
Releasing Procedure:
1. Press the [1] button to turn the power on.
2. Press the [FUNCTION] button to select the DVD/CD function.
3. Press the [ENTER] button and [VOCAL FADER] button
simultaneously for three seconds.
4. The message “UNLOCKED” is displayed on the screen
display panel and the disc tray is unlocked.
Note: When “LOCKED” is displayed on the screen display panel, the disc
tray lock is not released by turning the power on/off with the [1]
button.
6
NOTE OF REPLACING MOTHERBOARD BOARD OR

Playing music from a Bluetooth device
BLUETOOTH MODULE OR RC-S730 (WW)
When the MOTHERBOARD board or BLUETOOTH module or For a Bluetooth device
RC-S730 (WW) are replaced, please execute the below service 1. Press the [1] button to turn the power on.
mode. 2. Press BLUETOOTH on the unit to select Bluetooth function.
“BLUETOOTH” appears in the display panel.
Pairing this system with a Bluetooth device 3. Establish connection with the Bluetooth device.
Press BLUETOOTH on the unit to connect to the last
1. Press the [1] button to turn the power on. connected Bluetooth device.
2. Place the Bluetooth device within 1 meter from the unit. Perform the Bluetooth connection from the Bluetooth device if
3. Press BLUETOOTH on the unit to select Bluetooth function. the device is not connected.
“BLUETOOTH” appears on the display. Once the connection is established, the Bluetooth device name
Hint appears in the display panel.
• When there is no pairing information on the system (for 4. Press N.
example, when you use the BLUETOOTH function for Depending on the Bluetooth device,
the first time after purchase), “PAIRING” flashes on the – you may have to press N twice.
display and the system enters the pairing mode. – you may need to start playback of an audio source on the
Proceed to step 5. Bluetooth device.
• If the system is connected to a BLUETOOTH device, press
BLUETOOTH on the unit to disconnect the BLUETOOTH For an NFC-compatible smartphone
device. 1. Press the [1] button to turn the power on.
4. Hold down on the unit for 2 seconds or more. Touch the smartphone to the N-Mark on the system to establish
“PAIRING” flashes on the display. the Bluetooth connection.
5. Perform the pairing procedure on the Bluetooth device. Start playback of an audio source on the smartphone. For
6. Select the system’s name on the display of the Bluetooth details on playback, refer to the operating instructions of your
device. smartphone.
For example, select “SHAKE-X10 or SHAKE-X30 or
SHAKE-X10D or SHAKE-X30D or SHAKE-X70D”.
To disconnect the Bluetooth device
If passkey is required on the Bluetooth device, enter “0000”.
For a Bluetooth device
7. Perform the Bluetooth connection on the Bluetooth device.
8. When pairing is completed and the Bluetooth connection is Press BLUETOOTH on the unit.
established, Bluetooth device name appears on the display. “BLUETOOTH” appears in the display panel.
9. To cancel pairing operation, hold down on the unit
for 2 seconds or more until “BLUETOOTH” appears on the For an NFC-compatible smartphone
display. Touch the smartphone to the N-Mark on the system again.
Connecting with a smartphone by one touch (NFC) To erase all the pairing registration information perform
BLUETOOTH PAIRING HISTORY CLEAR test mode (Re-
Note: The operation in this mode must use a NFC-compatible smartphone fer page 21).
(Smartphones with a built-in NFC function [OS: Android 2.3.3 or
later, excluding Android 3.x])
1. Press the [1] button to turn the power on.
2. Download and install the app “NFC Easy Connect”.
Download the free Android app from Google Play by searching
for “NFC Easy Connect”.
3. Start the app “NFC Easy Connect” on the smartphone.
Make sure that the application screen is displayed.
4. Touch the smartphone to the N-Mark on the system until the
smartphone vibrates.
Complete the connection by following the instructions

displayed on the smartphone.
5. When pairing is completed and the Bluetooth connection is
established, the Bluetooth device name appears in the display
panel.
7
HOW TO OPEN THE TRAY WHEN POWER SWITCH TURN OFF

Note 1: After the side (L, R) panel, top panel section, fan bracket and DC fan are removed, this work is done.
Note 2: Please prepare the thin wire (clip etc. processed to the length of 8 cm or more).
1 Remove the side (L,R) panel, top panel section,

fan bracket and DC fan.
(Illustration of disassembly is omitted.)
hole
– Side view –
Insert the clip etc.
processed to the
length of 8 cm or
more in the hole tray
on the side of the
CDM and push. CD/DVD drive
3
8 cm or more
tray
Note: Push after it inserts it in this hole well.

– Top view – 2 Insert the clip etc.
CAPACITOR DISCHARGE FOR ELECTRIC SHOCK PREVENTION
Switching Regulator (SSN-172AD) Board (Conductor side view) (HCD-SHAKE10/SHAKE30/HCDSHAKEX10/HCDSHAKEX30)

In checking the Switching Regulator (SSN-172AD) board, make 3 capacitors discharge of C18, C20 and C27 for eletrical shock prevention.
800 :/5 W
800 :/5 W
C18 R
R C27
C20 R
800 :/5 W
8
CAPACITOR DISCHARGE FOR ELECTRIC SHOCK PREVENTION
Switching Regulator (SSN-171AD) Board (Conductor side view) (HCDSHAKEX70)

In checking the Switching Regulator (SSN-171AD) board, make 4 capacitors discharge of C18, C20, C27 and C28 for eletrical shock
prevention.
800 :/5 W 800 :/5 W 800 :/5 W
R R R
C27
C18 800 :/5 W

C28
C20
SERVICE POSITION
panel, top assy
TOP PANEL board
FL board
CDM90-DVBU204//M
MIC board
stand
MOTHERBOARD board 2CH DAMP board

(SHAKE10/SHAKE30/
HCDSHAKEX10/HCDSHAKEX30)
4CH DAMP board (HCDSHAKEX70)
9
SECTION 2
DISASSEMBLY
Note: Disassemble the unit in the order as shown below.
2-1. DISASSEMBLY FLOW
SET
2-2. PANEL, SIDE (L), PANEL, SIDE (R),

PANEL, TOP ASSY
(Page 11)
2-3. 2CH DAMP BOARD 2-4. 4CH DAMP BOARD

(SHAKE10/SHAKE30/HCDSHAKEX10/HCDSHAKEX30) (HCDSHAKEX70)
(Page 12) (Page 13)
2-5. BACK PANEL SECTION 2-6. BACK PANEL SECTION

(Page 14) (Page 14)
2-7. PANEL, LOADING ASSY

(Page 15)
2-8. CDM90-DVBU204//M
(Page 16)
2-9. FRONT PANEL SECTION

(Page 17)
2-10. MOTHERBOARD BOARD

(Page 17)
2-11. REGULATOR, SWITCHING (SSN-172AD) 2-12. REGULATOR, SWITCHING (SSN-171AD)

(Page 18) (Page 19)
2-13. SERVICE, OPTICAL DEVICE (7G),

FLEXIBLE FLAT CABLE
(Page 20)
10
Note: Follow the disassembly procedure in the numerical order given.

2-2. PANEL, SIDE (L), PANEL, SIDE (R), PANEL, TOP ASSY
:LUHVHWWLQJ :LUHVHWWLQJ
TOP PANEL board
TOP PANEL board pin, lead
pin, lead
wk top panel section

–7RSSDQHOERWWRPYLHZ–
–7RSSDQHOERWWRPYLHZ– wh flexible flat cable
(11 core) (CN6003)
qg four screws
(+BVTP 3 u 8)
wj
qj one screw
(+BVTP 3 u 8)
(HCDSHAKEX70)
w; CN005 (9P) ws flexible flat cable
A
(25 core) (CN122)
5 two screws
1 Insert the (+BVTP 3 u 8) wg CN451 (5P)
clip etc.
2 cover screw A
4 one tapping B
4 one tapping qk one screw
screw
screw (+BVTP 3 u 8)
wf CN601 (7P)
wd flexible flat cable
4 one tapping (6 core) (CN105)
screw
(SHAKE10/SHAKE30/
7 panel, side (L) 6 HCDSHAKEX10/HCDSHAKEX30)
ql CN007 (3P)
A wa CN003 (11P)
1 Insert the qh one screw qf panel, side (R) qs two screws

(+BVTP 3 u 8) (+BVTP 3 u 8)
clip etc.
4 one tapping screw
3 cover screw B qa one tapping
B screw
:LUHVHWWLQJ qd
filament tape FL board
9 cover screw A
8 Insert the
clip etc.
qh one screw
(+BVTP 3 u 8)
filament
tape qa one tapping screw qa one tapping screw
qa one tapping screw
0 cover screw B 8 Insert the clip etc.
filament tape RC-S730 (WW) MIC board

Note 2: When you install the connector, please install them correctly.
–7RSSDQHOERWWRPYLHZ– There is a possibility that this machine damages when not
correctly installing it.
Note 1: When installing the flexible flat cable, ensure that
the colored line is not slanted after insertion. OK NG NG
Insert is straight Insert is shallow Insert is incline
OK NG to the interior.
connector connector
Insert is straight to the interior. Insert is incline connector
flexible flat cable flexible flat cable
colored line colored line

connector connector
connector connector connector
11
2-3. 2CH DAMP BOARD (SHAKE10/SHAKE30/HCDSHAKEX10/HCDSHAKEX30)
9 three screws
(+PTPWH 2.6 u L (DIA8.0))
qa heat sink (M3)
2 two screws 3 two screws

qs four screws 0 sheet, thermal
(+BVTP 3 u 8) (+BVTP 3 u 8)
(+BVTP 3 u 8)
1 CN1003
(2P) C
qg 2CH DAMP
board
qf bracket,
4 bracket, fan heat sink
5 DC fan (white)
8 one screw
(+BVTP 3 u 8)
qd
7 CN1001 (10P)
6 flexible flat cable

(19 core) (CN1013)
There is a possibility that this machine damages when not
connector connector

connector connector
12
2-4. 4CH DAMP BOARD (HCDSHAKEX70)
qa three screws
(+PTPWH 2.6 u L (DIA8.0))
qd heat sink (M3)
5 two screws qg stopper, wiring

(+BVTP 3 u 8) qs sheet, thermal
4 two screws qf one screw
(+BVTP 3 u 8) 2 cushion (+BVTP 3 u 8)
qf four screws
(QJ, S) (+BVTP 3 u 8) C
3 CN1003 :LUHVHWWLQJ
(2P) rear side
qk 4CH DAMP stopper,
board wiring
4CH DAMP
board
6 bracket, fan
(black) qj bracket,
7 DC fan heat sink
0 two screws
(+BVTP 3 u 8)
qh
9 CN1001 (10P)
8 flexible flat cable 1 CN1011 (2P)

(19 core) (CN1013)
connector connector

connector connector
13
2-5. BACK PANEL SECTION (SHAKE10/SHAKE30/HCDSHAKEX10/HCDSHAKEX30)
3 four screws
(+BVTP 3 u 8)
1 one screw (HCDSHAKEX10/

7 back panel section (+BVTP 3 u 8) HCDSHAKEX30)
2 one screw (+B 3 u 6)
1 one screw
(+BVTP 3 u 8)
6 sheet,
service cover
5
(HCDSHAKEX10/ 4 five screws

HCDSHAKEX30) (+BVTP 3 u 8)
2-6. BACK PANEL SECTION (HCDSHAKEX70)
3 four screws
(+BVTP 3 u 8)
6 two screws
(+BVTP 3 u 8)
9 back panel section 2 one screw

(+B 3 u 6)
1 two screws
(+BVTP 3 u 8)
8 sheet,
5 service cover
4 five screws
7 DC fan
(+BVTP 3 u 8)
14
2-7. PANEL, LOADING ASSY
3 three claws
hole
– Side view – 4 panel, loading
assy
Insert the clip etc.
processed to the
length of 8 cm or
more in the hole
on the side of the
CDM and push. CD/DVD drive
2
8 cm or more
tray
Note: Push after it inserts it in this hole well.

– Top view – 1 Insert the clip etc.
15
2-8. CDM90-DVBU204//M
7 four screws
(+BVTP 3 u 8)
1 filament tape
0 CDM90-DVBU204//M
2 flexible flat cable (24 core)

(CN302)
6 flexible flat cable (5 core)

8 boss
(CN303)
Note 1: When you install the CD/DVD
drive (CDM90-DVBU204//M), 5 CN401 (6P)
please match the position of
the boss two places. qa three screws
3 cushion,
(+BVTP 3 u 8) saranet
9 4 core, ferrite
(30 u 50)
qs two screws
(+BVTP 3 u 8)
qd bracket, CDM
connector connector

connector connector
16

(10 core) (CN102)
4 panel, front assy
Note: When installing the flexible flat cable,

ensure that the colored line
is not slanted after insertion.
OK
Insert is straight to the interior.
:LUHVHWWLQJ
flexible flat cable
BT holder BLUETOOTH module
colored line
connector
NG 2 four screws
(+BVTP 3 u 8) front side
Insert is incline
flexible flat cable
filament tape
colored line
connector
HI-RGB RIGHT LED PC BO board
(EXCEPT HCDSHAKEX70)
HI-RGB RIGHT board
(HCDSHAKEX70)
2-10. MOTHERBOARD BOARD

2 one screw
(+BVTP 3 u 8)
2 four screws
(+BVTP 3 u 8)
3 MOTHERBOARD
board
1 CN001 (9P)
17
2-11. REGULATOR, SWITCHING (SSN-172AD) (SHAKE10/SHAKE30/HCDSHAKEX10/HCDSHAKEX30)
3 one screw
(+BVTP 3 u 8) 4 chassis, sub assy
D
E 3 one screw
(+BVTP 3 u 8)
5 eight screws
(+PWH 3 u 8 (SUMITITE)) 5 one screw
(+PWH 3 u 8 (SUMITITE))
F 6 stopper, wiring
8 REGULATOR, SWITCHING
(SSN-172AD)
:LUHVHWWLQJ 2 stopper, D
REGULATOR, SWITCHING 1 one screw wiring
(SSN-172AD) (+BV3 (3-CR))
7 CN1 (2P)
1 one screw F
(+BV3 (3-CR))
E
2 stopper, wiring
stopper, wiring 9 chassis assy (RAI) :LUHVHWWLQJ
REGULATOR, SWITCHING
(SSN-172AD)
stopper, wiring
Note : When you install the connector, please install them correctly.
core, ferrite
OK NG NG
to the interior.
connector connector
connector
18
2-12. REGULATOR, SWITCHING (SSN-171AD) (HCDSHAKEX70)
3 one screw 6 chassis, sub assy

(+BVTP 3 u 8)
D
5 bracket, L
E 3 one screw
(+BVTP 3 u 8)
4 two screws
(+BV3 (3-CR))
7 six screws
(+PWH 3 u 8 7 two screws
(SUMITITE)) (+PWH 3 u 8
(SUMITITE)) 7 one screw
(+PWH 3 u 8
(SUMITITE))
F
8 stopper, wiring
:LUHVHWWLQJ
(SSN-171AD)
1 one screw
0 REGULATOR, SWITCHING
(+BV3 (3-CR)) (SSN-171AD)
D
2 stopper,
wiring 9 CN1 (2P)
F
1 one screw
(+BV3 (3-CR))
stopper, wiring
E
2 stopper,
wiring
qa chassis assy (RYU)
:LUHVHWWLQJ
Note : When you install the connector, please install them correctly. REGULATOR, SWITCHING
There is a possibility that this machine damages when not (SSN-171AD)
correctly installing it. stopper, wiring
OK NG NG
to the interior.
connector connector
connector
19
2-13. SERVICE, OPTICAL DEVICE (7G), FLEXIBLE FLAT CABLE

1 six claws
2 chuck holder assy (T)
qa insulator qf filament tape

8 four insulator screws
qg flexible flat cable

qs service, optical (5 core)
device (7G)
qa insulator
qa insulator
qj holder, FFC
0
9
6 belt qk flexible flat cable
(24 core)
qh
3 Insert the thin
wire (clip etc.).
7 connector
qd base, lo assy loading assy (T)

4
5 tray – Bottom view –
,QVWDOODWLRQRIIOH[LEOHIODWFDEOH FRUH DQGIOH[LEOHIODWFDEOH FRUH

Note: This illustration sees the loading assy (T) from bottom side.
5 three claws
5 two claws
(24 core)
loading assy (T)
6 holder, FFC
3 Through the hole
4
terminal face 7 flexible flat cable

(24 core)
2 Through the hole 9 filament tape

Under the guide (5 core)
(Fold area)
Under the guide
20
SECTION 3
TEST MODE
PANEL TEST MODE USER RESET
This mode is used to check the buttons, knobs, screen display The user reset clears all data including preset data stored in the data
panel and LEDs. flash to initial conditions exclude history mode data.
Procedure: Procedure:
1. Press [1] to turn on the system. 1. Press [1] button to turn on the system.
2. Press [] button and [ TUNING – .] button simultane- 2. Press [DJ OFF] button and [ TUNING + >] button simul-
ously for 3 seconds. taneously for 3 seconds.
3. All LEDs and segments in screen display panel are lighted up. 3. “RESET” appears on the screen display panel. After that, the
This is the display check mode. screen display panel becomes blank for a while, and the system
Press [ENTER] button repeatedly to toggle different display goes to demo mode.
mode as below.
Segments on screen display panel: COLD RESET
All On --> 1st Group On --> 2nd Group On --> All On --> All This mode is used to reset all the user settings to factory setting.
Off Execute this mode when returning the unit to the customer.
Single color LEDs: Procedure:
All On --> 1st Group On --> 2nd Group On --> All On --> All 1. Press [1] button to turn on the system.
Off 2. Press [] button and [ TUNING + >] button simultane-
Multi Color LEDs: ously for 3 seconds.
White --> Red --> Green --> Blue --> Off 3. “COLD RESET” appears on the screen display panel. After
4. Press [  - ] button, the button and knob check mode is that, “SONY DEMO” appears on the screen display panel.
activated. The system automatically turn on and off once. Please be sure
5. In the button and knob check mode, the screen display that the system stay at demo mode finally before switch off the
panel displays “K 0 E0V0”. power supply.
Each time a button is pressed, “K” value increases.
However, once a button has been pressed, it is no longer DISC TRAY LOCK
taken into account. After all the buttons have been When the disc tray does not open and “LOCKED” appears on the
pressed, "K" value will toggle between "OK" and "K26". screen display panel, disc tray lock mode has been activated by the
“E” value increases in the manner of 0, 1, 2, 3 ... if shop front.
[MIC/GUITAR LEVEL] knob is turned clockwise, or it To release from Disc Tray Lock Mode
decreases in the manner of 0, 9, 8, 7 ... if [MIC/GUITAR 1. Press [1] button to turn on the system.
LEVEL] knob is turned counterclockwise. 2. Press [FUNCTION] button repeatedly to select DVD/CD
“V” value increases in the manner of 0, 1, 2, 3 ... if function.
[VOLUME/DJ CONTROL] knob is turned clockwise, or 3. Press [ENTER] button and [VOCAL FADER] button
it decreases in the manner of 0, 9, 8, 7 ... if [VOLUME/ simultaneously and hold down until “UNLOCKED” displayed
DJ CONTROL] knob is turned counterclockwise. on the screen display panel.
6. To release from this mode, press the buttons in the same
manner as step 2, or disconnect the power cord. BLUETOOTH PAIRING HISTORY CLEAR
This mode is used to delete the Bluetooth pairing history on the
VERSION DISPLAY MODE system.
This mode is used to check the software version. Procedure:
Procedure: 1. Press [1] button to turn on the system.
1. Press [1] button to turn on the system. 2. Press [FUNCTION] button repeatedly to turn the Bluetooth
2. Press [ TUNING – .] button and [LIGHT MODE] but- function.
ton simultaneously for 3 seconds. 3. Press [ENTER] button and [LIGHT MODE] button
The SC software version and CD/DVD software appear on the simultaneously for 3 seconds.
screen display panel. 4. The message “BT HISTORY” → “CLEAR” appears on the
After that, it returns to the default display. screen display panel. The pairing history has been deleted.
MODEL AND DESTINATION DISPLAY MODE SHOP FRONT DEMO

This mode is used to check the model and destination of the set. The playback started automatically and the “ * DEMO * ” appears
Procedure: on the screen display panel.
1. Press [1] button to turn on the system. This is the Shop Front Demo mode which is activated by the shop
2. Press [] button and [ TUNING – .] button simultane- front.
ously for 3 seconds.
All segments in screen display panel are lighted up. To release from Shop Front Demo Mode
3. Press [  + ] button. Model information appears on the 1. Press [] button and [SOUND FIELD] button simultaneously for
screen display panel. 5 seconds.
4. Press [  + ] button again. Destination information appears
on the screen display panel.
5. Press [] button and [ TUNING – .] button simultane-
ously for 3 seconds to exit.
21
HISTORY MODE
This mode is used to check important data stored in the system when PROTECTOR happened.
Procedure:
1. During demo mode, press [] button and [  +] button for 5 seconds to mode into history mode.
2. Press the [ TUNING + >] button or [ TUNING – .] button to check history data stored.
Display on screen display panel Description

P C O U N T ※ ※ No. of time protector happened (0 ~ 99)
P T ※ ※ ※ ※ Refer to protect type description
Single Power On Time until protector happened (0~99999 hours,
1 *h *h *h *h *h *m *m
0~99 minutes)
Total Power On Time [ no consider protector happened ]
2 *h *h *h *h *h *m *m
(0~99999 hours, 0~99 minutes)
F ※ ※ ※ ※ ※ ※ Input Function during protector happened
V O L ※ ※ ※ Volume setting (MIN / 1 - 50 / MAX)
B A S S ※ ※ ※ MEGA BASS setting (OFF / ON)
To release from History Mode.

To release from this mode, press [1] button.
Protect Type Description:
Error Code Description

1 There is possibility of over current happen at speaker output.
or
Unusual heat up of AMP IC by improper assembly of heat sink.
2 Defect of thermistor IC or charging circuit used by SPM (Sound Pressure Management) system.
3 Power supply over current.
4 DC appears in SP terminal by defect of AMP IC.
6 Defect of DC FAN and DC FAN driver circuit.
22
SECTION 4
ELECTRICAL CHECK
TUNER SECTION 0 dB = 1 ȝV FOCUS BIAS CHECK

oscilloscope
FM AUTO STOP CHECK (DC range)
signal MOTHERBOARD board

generator
CN302 pin 17 (RF) +
CN302 pin 1 (GND) –
set
Procedure:
+ 1. Connect the oscilloscope to CN302 pin 17 (RF) and CN302
75 pin 1 (GND) on the MOTHERBOARD board.
–
2. Press the [1] button to turn the power on, and press the
[FUNCTION] button to select DVD/CD function.
3. Set the test disc (CD: YEDS-18), (DVD: HLX-503 (NTSC) or
HLX-504 (PAL) on the tray and press [N] button to playback.
4. Confirm that oscilloscope waveform is as shown in the figure
Procedure:
below (eye pattern).
1. Turn the power on.
A good eye pattern means that the diamond shape () in the
2. Input the following signal from Signal Generator to FM
center of the waveform can be clearly distinguished.
antenna input directly.
VOLT/DIV: 200 mV
Carrier frequency : A = 87.5 MHz, B = 98 MHz, C = 108 MHz TIME/DIV: 500 ns
Deviation : 75 kHz
Modulation : 1 kHz
ANT input : 35 dBu (EMF) level:
1.1 ± 0.25 Vp-p (DVDSL)
Note: Please use 75 ohm “coaxial cable” to connect SG and the 1.0 ± 0.25 Vp-p (CD)
set. You cannot use video cable for checking.
Please use SG whose output impedance is 75 ohm.
3. Set to FM tuner function and scan the input FM signal with Checking Location:
automatic scanning. -MOTHERBOARD Board (COMPONENT SIDE)-
4. Confirm that input Frequency of A, B and C detected and
automatic scanning stops.
The stop of automatic scanning means “The station signal is

received in good condition”.
pin 1 (GND) pin 17 (RF)
CN302
23
Switching Regulator (SSN-172AD) Diagnosis Flow (HCD-SHAKE10/SHAKE30/HCDSHAKEX10/HCDSHAKEX30)
24
AC IN
(1)
(2)
The Power Control signal to Switching regulator is checked.
Is following power voltage OK? Check whether the state of the Cable and Outlet are normal.
No
If there are no problems, check circumference circuit for
(5) Main on/Sub on Standby Demo mode Power On Main on/Sub on Output of the Motherboard mount side.
(6) CN 4 :pin8 Low (0V) Low (0V) Hi (3.3V)
Yes
(3)
The Output from Switching regulator is checked.
Is following power voltage up to standard?
Standby Demo mode Power On No

CN4 pin1 13.5V±0.5V 13.5V±0.5V 13.5V±0.5V Replaces Switching regulator if it is not up to standard.
CN2 pin2-4 0V 0V -62.5V±5%
(4) pin5 0V 0V -25.5V±5%
pin7 0V 0V +25.5V±5%
pin8-10 0V 0V +62.5V±5%
pin1 0V 0V -45.5V±10%
SECTION 5
(1) AC input Yes

(2) Fuse
TROUBLESHOOTING
(3) Sub Power transformer

(4) CN 4 Connector END
pin1: Audio (13.5V)
pin2: Audio (GND)
pin3-4: LED (13.5V)
pin5-6: LED (GND)
pin7: AC-Det
pin8: PCON
pin9: LOW AC
(5) MAIN Power transformer
(6) CN 2 Connector
pin1: SPV (DC-45.5V)
pin2-4: -PVDD (DC-62.5V)
pin5: -VL (DC-25.5V)

pin6: GND
pin7: +VL (DC+25.5V)
pin8-10: +PVDD (DC+62.5V)
Switching Regulator (SSN-171AD) Diagnosis Flow (HCDSHAKEX70)
AC IN
(2)
(5)
(1)
Check whether the state of the
The Power Control signal to Switching regulator is checked.
Cable and Outlet are normal.
Is following power voltage OK?
No If there are no problems, check
circumference circuit for Main
Main on/Sub on Standby Demo mode Power On on/Sub on Output of the
(6) CN 4 :pin8 Low (0V) Low (0V) Hi (3.3V) Motherboard mount side.
Yes
The Output from Switching regulator is checked.

(3)
Is following power voltage up to standard?
Standby Demo mode Power On No Replaces Switching regulator if it

(4)
CN4 pin1 13.5V±0.5V 13.5V±0.5V 13.5V±0.5V is not up to standard.
CN2 pin2-4 0V 0V -62.5V±5%
pin5 0V 0V -24V±5%
pin7 0V 0V +24V±5%
(1) AC input pin8-10 0V 0V +62.5V±5%
(2) Fuse pin1 0V 0V -45.5V±10%
(3) Sub Power transformer Yes
(4) CN 4 Connector
pin1: Audio (13.5V)
pin2: Audio (GND) END
pin3-4: LED (13.5V)
pin5-6: LED (GND)
pin7: AC-Det
pin8: PCON
pin9: LOW AC
(5) MAIN Power transformer
(6) CN 2 Connector
pin1: SPV (DC-45.5V)
pin2-4: -PVDD (DC-62.5V)
pin5: -VL (DC-24V)
pin6: GND
pin7: +VL (DC+24V)
pin8-10: +PVDD (DC+62.5V)
25
Optical Block Diagnosis Flow (1/2)
26
REMOVE SIDE PANEL
REMOVE TOP PANEL
TURN ON
TRAY IN
Does Optical pickup move to inner circumference? No Checks CL335 for +3.3V and +1.2V REG IC303. No Checks IC303 circumference circuit for +1.2V.
(Visual check) Does it output the power voltage of 3.3V and 1.2V? Checks IC002 (JL040) circumference circuit for +3.3V.
Yes Yes
Checks CN401 SL+/SL- signal. No Checks circumference circuit for SL+/SL- of IC401.
Does it output the signal? Checks circumference circuit of IC301 FMO Signal.
Yes
The Sled motor has a problem.
Replaces BU.
Does Spindle motor rotate? No Checks CN401 SP+/SP- signal. No Checks circumference circuit for SP+/SP of IC401.
(Visual check) Does it output the signal? Checks circumference circuit of IC301 DMO Signal.
Yes Yes
The Spindle motor has a problem.
Replaces BU.
Does Optical pickup do focus search? No Checks CN302 FCS+/FCS- signal. No Checks circumference circuit for FCS+/FCS- of IC401.
(Visual check) Does it output the signal? Checks circumference circuit of IC301 FOO Signal.
Yes Yes
The Optical pickup has a problem.
Replaces BU.
A
Optical Block Diagnosis Flow (2/2)
Does laser diode become luminous? No Checks JL306 (LD780) signal. No Checks circumference circuit of Q402.
(Visual check) Does it output 2V when laser become luminous? Checks circumference circuit of IC301 LDO1.
Yes Yes
Replaces BU.
DISC IN
Yes
Is output level of RF signal JL317 up to standard? No If it is not up to standard,

RF Level = 1.05 ±0.45 Vpp
Lens cleaning is performed.
Test disc (CD: YEDS-18, DVD: HLX-503 (NTSC) or HLX-504 (PAL))
Yes
Yes
Is output level of RF signal JL317 up to standard?
No
RF Level = 1.05 ±0.45 Vpp Replaces BU if it is not up to standard.
Test disc (CD: YEDS-18, DVD: HLX-503 (NTSC) or HLX-504 (PAL))
Yes
Is there no problem with Long term Aging Test (60min)?
Confirms that there is no sound skip. No
Yes
Replaces BU.
END
27
2CH DAMP / 4CH DAMP / MOTHERBOARD Mount Diagnosis Flow (1/2)
28
PLAY MUSIC
Yes
No No
Is there audio output from 2CH DAMP/ Checks 13V output of CN001 1pin(Main ON). Reinserts the cable or Exchanges.
4CH DAMP Board? Is the power voltage OK? If there are no problems, checks output of
Switching Regulator Board.
Yes Yes
MOTHERBOARD Board
Checks 3V output of CN001 8pin(Main ON). No Reinserts the cable or Exchanges.
Is the power voltage OK? If there are no problems, checks output of
Main ON of MOTHERBOARD Board side.
Yes
No Reinserts the cable or Exchanges.

Checks +62.5V output of CN1001 10pin(+VH),
If there are no problems, checks output of
-62.5V output of CN1001 2pin(-VH) and -45.5V
Switching Regulator Board.
output of CN1001 1pin -45.5V.
Is the power voltage OK?
2CH DAMP/4CH DAMP Board
Yes
Checks OUT terminal -50.5V output of REG IC1005. No Checks circumference circuit of REG IC1005.
Or, checks GND and OUT Terminal with Tester.
If there are no problems, exchanges IC1005.
Is it shorted out?
Yes
A B
2CH DAMP / 4CH DAMP / MOTHERBOARD Mount Diagnosis Flow (2/2)
A B
Checks OUT Terminal 7V output of REG IC1006 or, No Checks circumference circuit of REG IC1006.
checks GND and OUT Terminal with Tester.
Is it shorted out?
Yes
Checks OUT Terminal -7V output of REG IC1007 or, No Checks circumference circuit of REG IC1007.
checks GND and OUT Terminal with Tester.
Is it shorted out?
Yes
Leave 2CH DAMP/4CH DAMP Mount to a state of it only No 2CH DAMP/4CH DAMP Board
and, checks Power Audio Driver (MOSFET) with Tester. Replaces 2CH DAMP/4CH DAMP Board
Is it shorted out? (Refer to Page 30 and 31.)
Yes
Assembles into the unit again then, checks No

whether there is the audio output from 2CH DAMP/ Replaces 2CH DAMP/4CH DAMP Board
4CH DAMP Board.
Yes
END
29
MOSFET Confirmation for 2CH DAMP Mount
30
CL1071
C1127
C1114
C1189
C1115
C1125
C1123
C1122
CL1051
C1126
CL1053
C1147
R1168 CL1052
R1174 R1177 CL1009

CL1010
R1175 R1176
R1275 R1166
CL1030 CL1074
CL1029
CL1026
CL1073
CL1025
Tester
CL1024
R1017 R1048 CL1072
CL1028
D1006
D1003
CL1027
Tester C1014 C1047
Tester C1015
Tester C1048
R1014 R1051
CL1063
C1001 C1005 C1039 C1035

CL1003 CL1008
C1006 CL1000 C1012 C1046 CL1005 C1040
R1008 R1044
CL1001 CL1006
CL1004 CL1011
CL1002 CL1007
C1240
R1066 R1067
CL1034 CL1033
R1011
R1009
R1065 R1068
CL1039
C1201 C1202
R1033
CL1043 R1060
R1028
R1023
R1201
R1200
A
CL1038
D1032
K
CL1049
CL1048
CL1040
CL1047
CL1037 CL1036
CL1046 CL1062
CL1045
CL1044
CL1068
CL1069
CL1041
C1244
CL1061
C1251
CL1035
<Note>
Please check each channel’s resistance value for the Coil’s terminal and Capacitor’s + and – terminal.
These terminal is equal to resistance value for POWER AUDIO DRIVER terminal.
MOSFET Confirmation for 4CH DAMP Mount
CL1070
CL1056
C1123
C1122
C1128
C1129
C1120
C1194
C1116
CL1060
C1121
C1127
C1118
C1189
C1119
C1114
C1115
C1125
CL1071
C1126
CL1058 CL1051
CL1055
CL1030 CL1059 CL1057 CL1054 CL1052
C1147
CL1031 CL1053
CL1021 CL1009
R1174 R1177 CL1022 CL1010
R1175 R1176
CL1032 R1275 R1166
CL1078
CL1074 CL1029
CL1075
CL1026
CL1073
R1168
CL1025
CL1024
CL1072 CL1077
Tester Tester Tester

R1093 R1124 R1017 R1048 CL1076
D1013
D1016
D1006
D1003
CL1028
CL1027
Tester Tester Tester Tester Tester
C1014
C1106
C1073
C1047
C1074 C1107 C1015 C1048
R1090 R1127 R1014 R1051
CL1063
C1060 C1098 C1001 C1005 C1039 C1035

CL1015 C1064 CL1020 C1094 CL1003 CL1008
C1065 CL1012 C1071 C1105 CL1017 C1099 C1006 CL1000 C1012 C1046 CL1005 C1040
R1084 R1120 R1008 R1044

CL1001
CL1013 CL1018 CL1006
CL1016 CL1023 CL1004 CL1011
CL1014 CL1019 CL1002 CL1007

C1241 C1240
R1142
R1066 R1067
R1143
R1087
R1141
R1011
R1009
R1085
R1065 R1068
CL1034
R1144
C1199 C1201 C1202
C1200
R1033
R1136 R1060
CL1033 R1104 R1028
R1023
R1201
R1109
R1199
A
R1200
R1099
A
R1198
C1251
D1033
D1032
CL1040
K
K
CL1049
CL1048
CL1047
CL1038
CL1037
CL1036
CL1062
CL1068 CL1045
CL1044
CL1046
CL1043 CL1039
CL1041
C1252 CL1069
C1244
CL1061
CL1035
<Note>
Please check each channel’s resistance value for the Coil’s terminal and Capacitor’s + and – terminal.
31
These terminal is equal to resistance value for POWER AUDIO DRIVER terminal.
SECTION 6
DIAGRAMS
• Circuit Boards Location
2CH DAMP board 4CH DAMP board (HCDSHAKEX70)

(SHAKE10/SHAKE30/
LED DRIVER board
MOTHERBOARD board
REGULATOR, SWITCHING (SSN-172AD)

(SHAKE10/SHAKE30/HCDSHAKEX10/HCDSHAKEX30)
REGULATOR, SWITCHING (SSN-171AD)
(HCDSHAKEX70)
FL board
TOP PANEL board
RC-S730 (WW)
MIC board
IR board
HI-RGB LEFT board
SKY BLUE board

(SHAKE10/SHAKE30/ BLUETOOTH module
BAR CENTER board (HCDSHAKEX70)
HI-RGB RIGHT LED PC BO board

MS-476 board
(SHAKE10/SHAKE30/
HI-RGB RIGHT board (HCDSHAKEX70)
32
6-1. BLOCK DIAGRAM - RS SERVO, USB, HDMI Section -
&'5)$03
)2&8675$&.,1*(5525$03
&'6<67(0352&(6625
',*,7$/6(592352&(6625
,& +&'6+$.(;+&'6+$.(;+&'6+$.(;
J907
&9%6 98 9,'(2287
5) 119 5),3
&1
92$$ 125 5)B$ 7;3 94
'$7$
1
92%% 124 5)B% 7;1 93
'$7$±
3
92'& 123 5)B& '$7$
7;3 91 4
92'' 126 5)B' '$7$±
7;1 90 6
'$7$
7;3 88 7
'$7$±
7;1 87 9
&/2&.
5 7;&3 85 10 +'0,287
9& 9 &/2&.±
7;&1 84 12 79 $5&
6&/ 9
8
+'0,B6&/ 28 15
3' 0', 6'$ 9
+'0,B6'$ 29 16
+273/8*'(7
*3,2+3/* 81 19
932:(5
9 18
13
$872
)(/'&' 32:(5&75/ 128 )(B&'B,23 $5&%8))(5 14
&(&'$7$6:,7&+
4 9 /'2 ,&
4a44
< 2
$872
)(/''9' 32:(5&75/ 127 )(B'9'B,23 $ 3 >001B
4 10 /'2 < 5 $5&B63',)B,1 MAIN SECTION
(Page 34)
X7$/2 4
86%6:,7&+
X301
6(59,&(237,&$/ ,&
0+]
'(9,&( * &1
X7$/, 3
' 3
86%B'0 20 11 ' ' 5
2 5(&3/$<
'
/2'9'+,&' 06: 18 06: 86%B'3 19 3 ' ' 9
9 $
1
'
14 &'B95 9%86
'
&'B95
6
((3520
,& 4 10 2
'9'B95 15 '9'B95
6)B&6B 24 1 &6
25 2 626,2 151 150 27
6)B'2
10 &(&,1
'3
'0
86%B+267B6(/
6)B', 26 5 6,6,2
&+6<67(0 15 &(&287
6)B&. 27 6 6&/.
02725'5,9(5
,& 06'5$0
,&
)&6 14 )2&86
1 17 )22
)&6± 13 &2,/'5,9(5
8'40
/'40
6<67(0
5$6
&$6
'4±'4 $±$
&/.
%$
%$
:(
75. 16 )2&86 &21752/
4 12 '02 ± ,&
75.± 15 &2,/'5,9(5 20 21 38 15 39 18 17 16
±
86%
&203$5$725
6/ 17 )2&86
23 13 )02 ,&
6/± 18 &2,/'5,9(5
41±±50 75±±61 72 73 60 49 59 70 69 68
11 86%2&6'B/(' 35 7 287 B,1 5 86%9
%$
%$
5&/.
'40
'40
5$6
&$6
5:(
63 )2&86
26 16 752 5'±5' 5$±5$
63± 12 &2,/'5,9(5
,)6', 35 22 07.6'2
%,$6 27 6 9 ,)6'2 38 20 07.6',
,)6&. 37 17 07.&/.
087( 28 108 087(
3567B 32 14 07.5(6(7
,)&6B 34 19 07.;,)&6
&1 ,)%6< 36 16 07.%86<
1
/2$'
9 9275
6LJQDOSDWK
/2$' $8',2',*,7$/
&211(&772 2 10 9275 6 8 &'02725
75$<,1 ):'
06%2$5' 3 3
75$<287 5(9 7 &'02725 9,'(2
5
&'3/$<
12 &'0/2$'6: 86%
13 &'081/2$'6:
5FKLVRPLWWHGGXHWR
VDPHDV/FK
33 33
6-2. BLOCK DIAGRAM - MAIN Section -
AUDIO/PARTY AUDIO/PARTY AUDIO/PARTY AUDIO/PARTY

L R L R
CHAIN IN (TV) CHAIN IN (TV) CHAIN OUT CHAIN OUT
J602 (1/2) J602 (2/2)

SIGNAL
SELECTOR
BIAS IC602 OP AMP
MIC AMP STEREO A/D DETECTOR IC601
IC2202 MIC AMP CONVERTER Q605, Q607
IC2101 IC609
5 Y1 Y 3 3 + OUT 1
J2204 14 X1 X 13 5 + OUT 7
MIC2/ 3 1 5 7 14 IN BUFFOUT 7 13 VINL BCK 8
GUITAR LINK SET
DET 3 14 VINR LRCK 7 Q603
5 BUFFIN OP AMP
OUT 4 DOUT 9 IC603
MIC DETECT
SCKI
J2203 MUTE
Q2203, Q2205 PROTECT
MIC1 6 VOUTL 7 3 + OUT 1 1 Y0 A 10
Q602
STEREO A/D VOUTR 8 5 + OUT 7 12 X0
CONVERTER
IC904 BCK 1
LRCK 3 ANALOG MUTE SW

STEREO D/A
SCK 16 SELECTOR Q606
CONVERTER
IC914 Q612
DATA 2
>002B
STEREO D/A
VINR 14 48 VINR
CONVERTER 13 BCK OUTL 6 FRONT-L AMP SECTION
VINL 13 47 VINL IC604
STEREO A/D
MPIO_C2/ALRCK_I1
(Page 35)
CONVERTER LRCK 7 9 15 LRCK
OUTR 7 R-CH
IC606 BCK 8 8 MPIO_C1/ABCK_I1
DOUT 9 10 MPIO_C3/ADIN_1
SCKI
12 SCK
6
14 DIN >001B
109
MPIO_A1 4 RS SERVO,
ACLK
RXIN3 32 ARC_SPDIF_IN USB, HDMI

ALRCK 114 29 RXIN6/ALRCK_I0 SECTION
ASDATA0 115 28 RXIN7/ADIN_0 XTO 40
X602
(Page 33)
ABCK 110 30 RXIN5/ABCK_I0 24.576MHz
XTI 39
FM DRIVER CD RF AMP EEPROM

13 MPIO_B2/ALRCK_I2
(FM RECEIVER) FOCUS/TRACKING ERROR AMP IC105
IC902 CD SYSTEM PROCESSOR 14 MPIO_B3/ADIN_2
DIGITAL SERVO PROCESSOR
MDI/SDA 24 2 SDA
ERROR/INT0
IC301 NPCM/INT1
CN603 (2/2) DOUT MC/SCL 25 7 RST
LRCK
BCK
RST
SCL
ANTENNA
2 1 FRF1 LRCK/LOUT 13
FM 1 2 17 18 19 34 6
BCLK/ROUT 12 R-CH
IISD 14
52 120 111 42 41 28 26 24 38 125 32 47 33 30 29 43 40

ZIN_CONVERTER/SD_D1_0
MIC-DET1
DIR-RESET/SD_LED1
MIC_DET2
DIR-INT0
DIR-INT1
SSI3-DI
DIR-CP-SCL
SSI0_DO(PARTY CHAIN)
SSI3_LRCKO
SSI3_BCKO
LINK-DET
SSI0_DI(MIC)
SSI0_LRCKO
SSI0_BCKO
AUDIO-CLK-OUT
SSI2-DO(FR)
/LINE-MUTE 48
SYSTEM CONTROL LINK-SET 115

IC109 (2/4)
16 X1 DA 11 128 ST-SDA
BT-RXD(MD-CLK)
X900
Q-Flash-SIO1
Q-Flash-SIO2
Q-Flash-SIO0
Q-Flash-SIO3
12MHz CK 8
Q-Flash-CLK
127 ST-SCL
Q-Flash-CS
17 X2
BT-RESET
AUDIO-X1
AUDIO-X2
6LJQDOSDWK
BT-TXD
BT-CTS
BT-RTS
USB-X1
USB-X2
IIC/RDSI 6 45 ST-RDS
EXTAL
BT-ON
XTAL
: AUDIO
65 133 164 165 113 114 70 71 91 92 139 140 169 172 166 170 168 167 : TUNER (FM)
BUS BUFFER
CN102 IC102 (1/3) : CD PLAY
X105 X103 X104
BT-RXD 14.5MHz 12.288MHz 48MHz : MIC
4 5 2A 2Y 6 1 2 3 5 6 7
5FKLVRPLWWHGGXHWR
CS
SO/SIO1
WP/SIO2
SI/SIO0
SCLK
HOLD/SIO3
BT-TXD
5 VDPHDV/FK
BT-CTS
6
BLUETOOTH MODULE BT-RTS
7
BT-RESET
9 EEPROM
IC106
BLUETOOTH
3.3V
8 POWER CONTROL
Q103, Q104
34 34
6-3. BLOCK DIAGRAM - AMP Section -
POWER AMP
+63V
IC1008
DIGITAL AUDIO MOSFET SHAKE10/SHAKE30/HCDSHAKEX10/ SHAKE10/SHAKE30/HCDSHAKEX10/

HO1 15 TB1002
Q1000 HCDSHAKEX30: FR HCDSHAKEX30
FR/FL+ FR/FL+ HCDSHAKEX70: FL+ 1
OP AMP CSL1 17
SPEAKERS
IC1009 IMPEDANCE
HCDSHAKEX70 DIGITAL AUDIO MOSFET
>002B LO1 18 3 USE
Q1001
FRONT-L 7 VINL1 VOUTL1 26 8 IN+1 TH1002
MAIN SECTION COM 20 DC DETECT
2 IN-2
(Page 34) RESET -63V SWITCH
SWITCH 11 CSD OTP 23 Q1003 HCDSHAKEX70
Q1002 +63V 1
SHAKE10/SHAKE30/ DIGITAL AUDIO MOSFET SHAKE10/SHAKE30/HCDSHAKEX10/ LEFT SPEAKER
HCDSHAKEX10/HCDSHAKEX30 HO2 28 IMPEDANCE
Q1004 HCDSHAKEX30: FL
VOUTR1 25 9 IN-1
FL/FL- FL/FL- HCDSHAKEX70: FL- 3 USE
CSL2 26
32 CLK DIGITAL AUDIO MOSFET

LO2 25 Q1005
CLK TB1003
SWITCH
DA
CL
Q1027 -63V
HCDSHAKEX70
18 19
POWER AMP
+63V
IC1010
DIGITAL AUDIO MOSFET TB1000

HO1 15
Q1006
FR+ FR+ 1
CSL1 17
DIGITAL AUDIO MOSFET

LO1 18
Q1007
8 IN+1 TH1001
COM 20 DC DETECT
2 IN-2 RIGHT
-63V SWITCH SPEAKER
OTP 23 Q1009 IMPEDANCE
+63V USE
DIGITAL AUDIO MOSFET
HO2 28
RESET Q1010
FR- FR- 3
SWITCH 11 CSD
CSL2 26
Q1008
32 CLK DIGITAL AUDIO MOSFET
LO2 25 Q1011
CLK
SWITCH
Q1028 -63V DETECT
SWITCH
Q1025
13V CN1003
DC FAN
2
FAN DRIVER
1A
DC DETECT BUS BUFFER Q1020
D1030 IC102 (2/3)
SWITCH
1Y
Q1019
3
CLK CN1011
SWITCH DC FAN
Q1029 FAN DRIVER
Q1022
AMP
SWITCH FAN PROTECTION
Q1018 (LOCK)
Q1023
FAN RESET FAN PROTECTION

SWITCH (LOCK)
Q1021 Q1024
FAN RESET FAN RESET

SWITCH SWITCH HCDSHAKEX70
Q1030 Q1026
56 57 53 96 78 66
6LJQDOSDWK
EVOL-DATA/TOUCH_INT2
EVOL-CLK/DAMP-MUTE
/AMP-RESET
AMP-PROTECT
MD-CLKS
AMP_CLK/SD_PCON
: AUDIO
SYSTEM CONTROL 5FKLVRPLWWHGGXHWR
IC109 (3/4)
VDPHDV/FK
FAN_DET/TOUCH-RESET1 1
35 35
6-4. BLOCK DIAGRAM - PANEL, POWER SUPPLY Section -
VACUUM DIN 4 FL_SOUT/LCD-SDA SPM-C-MON 79

FLUORESCENT CLK 2 FL_CLK/LCD-CLK
DISPLAY STB 176 LCD-CSB
ND2001 PROTECTION CONTROL
PCONT-DAMP 118
+6V REG. VOLTAGE REGULATOR Q576
VIN FL+13V POWER CONTROL
IC1003 IC009
PCONT-BTSTBY 122 PROTECTION
POWER Q009 PROTECTION CONTROL
VH CONTROL +1.2V 3 SW1 VIN1 1
+3.3V Q575
Q2006
POWER CONTROL
D+3.3V PROTECTION 14 SW2 VIN2 16
SW Q008
PROTECTION CONTROL
REMOTE CONTROL Q574
RECEIVER 135 SIRCS RES 76 4 VOUT VDD 2
IC010
VOLTAGE REGULATOR, SWITCHING
EN1001 PROTECTION CONTROL
DETECTOR (SSN-172AD) BOARD
VOLUME/ IC103 Q572 (SHAKE10/SHAKE30/
83 MASTER-VOLUME/MIC-VOLUME
DJ CONTROL HCDSHAKEX10/HCDSHAKEX30)
EN1002 (SSN-171AD) BOARD
PROTECTION CONTROL (HCDSHAKEX70)
MIC/GUITAR LEVEL 82 MIC-VOLUME C-CONT 55
Q571
POWER CONTROL
+1.2V 1 VO VCC 6 PROTECTION
S1003 ~ S1009, Q005
85 AD-KEY1
S1025, S1027 ~ S1030
+1.2V REG. MAIN-ON
IC303
S1001 ~ S1002,
S1015 ~ S1022, POWER CONTROL POWER CONTROL
84 AD-KEY0
S1026, PROTECTION PROTECTION
S1031 ~ S1032 +3.3V REG.
IC305 Q457 Q006
+VH +VH
SHAKE10/SHAKE30/ CE 1
HCDSHAKEX10/HCDSHAKEX30 S1014 45 ST-RDS +3.3V 3 VOUT POWER CONTROL
PROTECTION SWITCH
VDD 4 PROTECTION HCDSHAKEX70
+5.2V REG. Q1032
Q007
SYSTEM CONTROL IC001
D3501~D3503 LED DRIVER IC109 (4/4)
POWER CONTROL SHAKE10/SHAKE30/ PROTECTION SWITCH +VL
IC1001
+5.2V PROTECTION 14 SW2 HCDSHAKEX10/HCDSHAKEX30 Q1031
SIN 2 117 RGB-SOUT Q459
OUT8
13 - 15
D101 I SCK 3 134 RGB-SCLK USB+5V 3 SW1 VIN1 1

OUT10 TO +7V REG.
TRANS 4 173 RGB-TRANS-LED VIN2 16 +7V
AMP IC1006
PWMCLK 21 136 RGB-PWM-CLK SECTION
OUT1
16 - 18
HCDSHAKEX70 VBUS-OE/SD_WP_0 112 5 EN1 +13.5V

D102 I
OUT3
POWER CONTROL PROTECTION SWITCH
HCDSHAKEX10/HCDSHAKEX30 HCDSHAKEX70
PROTECTION Q1033
12,19,20
OUT7,
D103 OUT14, HCDSHAKEX70 Q302, Q303
OUT15 SHAKE10/SHAKE30/ PROTECTION SWITCH
MTK-POWER-CTRL 59 HCDSHAKEX10/HCDSHAKEX30 -VL
OUT0 +3.3V REG. Q1032
D1006~D1007,
5-9
I IC008
D1009~D1015 OUT4 SOUT 22
CONT 1
+5V 4 VOUT +5V REG. TO -7V REG.
+3.3V 3 VOUT VDD 4 IC1000 VIN 5 -7V
LED DRIVER AMP IC1007
IC1002 SECTION
OUT2, +3.3V 3 VOUT POWER CONTROL

7,10,12
VDD 4 +5V REG. +9V REG.

D201, D202 OUT5, PROTECTION +13.5V
SIN 2 IC006 IC004
OUT7 ST-CE 44 1 CE Q004
SCK 3
+3.3V REG.
OUT0, TRANS 4
5,13,15
IC903
D001, D002 OUT8, PWMCLK 21 POWER CONTROL
OUT10 PROTECTION
SOUT 22
Q461
LED DRIVER PCONT-PSAVE-PROTECT 60

IC6001
PROTECTION POWER CONTROL
SIN 2 SWITCH PROTECTION
OUT0 Q012 Q011
SCK 3
5 - 19
L I
OUT14 TRANS 4
+13V -VH -VH
PWMCLK 21
SOUT 22
LED PROTECTION PROTECTION PROTECTION
SPEAKER L/R -12V REG.
LED DRIVER /SD-FAST 49 SWITCH SWITCH SWITCH -VG (AC IN)
IC1005
IC6002 Q1016 Q1014 Q1015
SIN 2 SPM-AMBIENT-TEMP 80 TH571

OUT0
SCK 3 BUS BUFFER
5 - 19
I 11 4Y 12 AC CUT SWITCH AC DET

R
TRANS 4
AC-CUT(MD-BOOT0) 63 IC102 (3/3) 4A Q107, Q109
OUT14
PWMCLK 21
AC_LOW_DET/TOUCH-RESET2 94 LOW AC DETECT SWITCH LOW_AC

Q108
36 36
• Note for Printed Wiring Boards and Schematic Diagrams
Note on Printed Wiring Board: Note on Schematic Diagram:

• X : parts extracted from the component side. • All capacitors are in μF unless otherwise noted. (p: pF)
• : parts extracted from the conductor side. 50 V or less are not indicated except for electrolytics
• : Pattern from the side which enables seeing. and tantalums.
(The other layer’s patterns are not indicated.) • All resistors are in  and 1/4 W or less unless otherwise
specified.
Caution: • 2 : nonflammable resistor.
Pattern face side: Parts on the pattern face side seen from • C : panel designation.
(Conductor Side) the pattern face are indicated.
Parts face side: Parts on the parts face side seen from Note: The components identified by mark 0 or
(Component Side) the parts face are indicated. dotted line with mark 0 are critical for safety.
Replace only with part number specified.
t Indication of transistor Note: Les composants identifiés par une marque
C 0 sont critiques pour la sécurité.
Ne les remplacer que par une piéce portant
Q These are omitted. le numéro spécifié.
B E
• A : B+ Line.
• B : B– Line.
• Voltage and waveforms are dc with respect to ground
D under no-signal (detuned) conditions.
Q These are omitted. no mark : TUNER
< > : CD PLAY
G S : Impossible to measure
*
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production
Q tolerances.
• Waveforms are taken with a oscilloscope.
B C E Voltage variations may be noted due to normal production
tolerances.
These are omitted. • Circled numbers refer to waveforms.
• Signal path.
Q F : AUDIO
f : TUNER (FM/AM)
N : MIC
B C E
J : CD PLAY
These are omitted. E : USB
• Abbreviation • Abbreviation
AR : Argentina model AR : Argentina model
AUS : Australian model AUS : Australian model
CND : Canadian model CND : Canadian model
E4 : African model E4 : African model
EA : Saudi Arabia model EA : Saudi Arabia model
LA9 : Latin-American model LA9 : Latin-American model
Note 1: When the complete MOTHERBOARD board

is replaced, refer to “NOTE OF REPLACING
MOTHERBOARD BOARD OR BLUETOOTH
MODULE OR RC-S730 (WW)” on page 7.
Note 2: When the MS-476 board is defective, exchange

the entire LOADING COMPLETE ASSY (T).
37 37
6-5. PRINTED WIRING BOARD - MOTHERBOARD Board (Component Side) - • See page 32 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
MOTHERBOARD BOARD
A (COMPONENT SIDE)
Ú SHAKE10/SHAKE30 J602
¹ HCDSHAKEX10/HCDSHAKEX30/HCDSHAKEX70 L R
EXCEPT SHAKE10
AUDIO/PARTY CHAIN AUDIO/PARTY CHAIN
IN (TV) IN (TV)
¹
AUDIO/PARTY CHAIN AUDIO/PARTY CHAIN J907
OUT OUT VIDEO OUT
ANTENNA FOR
FM SERVICE ONLY
CN1000
(CHASSIS)
HDMI OUT
B (TV) ARC V (CHASSIS)
CN101
4 3 8 7
CN603
Q457, Q602 2 1 JL635 6 1
C681
C680
C1 B2 E2
C980
JL614 1 19
E1 B1 C2 JL901 R126 R124

JL900
R1012
C1010 R1021 JL905
JL631
C682
R687 JL1000 JL1001 JL1002
C1009
R1022
JL605 R690
JL604 JL1005 JL1003 Z903
Z001 R1010 R1011
R691
JL619
C R1025
C642
CL328
R674 R661
JL620 R1023 R1024 CL329
R1014 R1015
IC1001
C640
JL1006 ¹
R653
R1029
RB303
C644
IC606
R756
C648
R641
RB302
RB305
R311 JL110
C1011
R627
C364
R309
R628
27
28
C649 C653 CL380
Q602
R1027
R688
JL111
RB301 RB304
C655 R368
IC306
R624
CL309 CL300
R625
R367
96 65
R390
R382
C359
97 64
JL601
JL330 R380
R379
JL602
R036
C360
RB307 RB306
CL310 (CHASSIS)
R365
D CL316 R360
C341
C365
R358 CL315
IC301
R955
C954
R670
JL352 R369 JL056
C952 C951
C337
128
(CHASSIS)
>004P
C363
¹ JL353 C334
C076
33
IC305 R351R349
1
R637
32
JL057
R371
C981 X602 JL348
C963
54
1
R633 R953 R958 C353
C985
TOP PANEL BOARD
RB308
C958 R334 C308 R340
R342
R344 RB309
R332 JL350 C362
R666 Ú R388
37
48
C307
FB320
CN1004
1
36
SL403 R402
R989
JL331 X301 R415
R327
R331
IC904
R981
C356 CL338 SL402 C411 C402
R355
FB321
1 23
R982
R983
R988 JL349 C322 C323
IC302
CL308
SL401
R418 C413 SL404 R401
C403
(Page 43)
R408
R345
25
12
R987
JL404
R984
24
CN302
13
R305
E 2 24 CL335 R354 FL301
R470
R472
R985
R307
R986 JL341
C401
C412
R957
C324
R959
C606
R329
SL301
R335
JL346
R952
C468
IC453
R301
R389
JL347 JL305
R480
R951
R950
6
C467
C408
JL463
JL309 JL311 JL317
CONNECT TO JL318 R404
FB455
R409
SERVICE, OPTICAL DEVICE (7G)
JL313 JL321 JL462
SL406
JL322
SL408
SL405
SL407
JL303 JL315 JL319
CN451
C612 C601 JL307 JL455
JL461 C419 R410 JL403
JL402
Z904 C073 JL323 JL405
JL401
1 23 JL454 JL406 CONNECT TO
C418
R499
CN302
JL301 JL464 SERVICE, OPTICAL DEVICE (7G)
2 24 JL460
5
R048
C071 JL324
JL603
>001P
Q007 JL302 JL306 JL310 JL329 6 1
7
JL032 C366 JL320
CN401
JL304
F E
D402
JL312
JL314
C405 C406
R323
JL308 JL316
8 7
MIC BOARD
R040
D401
C367
R039 R316 JL906
1
CONNECT TO
Q006
2
E
C311
¹ R1006 MS-476 BOARD
C1000 R1003
R386
NO1102
JL022 JL050
R668
R1004
CN303
4
JL613
5
JL328 JL055
K
C066
(Page 46)
D1001
JL023 R030
C420
Q1005
C423
C1001
9
JL326 E E
A
JL325 Q1001
Q457
7
C064
R028
JL615
C609
JL021
R1001
R1005
R1007 R1002
Q459
E R034
Q1002
E
JL327 JL024
Q005
E
Q1000 (CHASSIS)
E
R037
CN601
C065
R645
JL616
C622
JL908
¹ JL294 JL059
G C067
R274
R582
JL278
C502
1
R229 R230
R595
R211
R219
FB116
R218
R999
2
R213
JL129
R201 R295
R193 JL182
R224
C139
R257
¹
R215
R254
1
JL183
JL909 JL281 JL282

R171
R150
R181
JL189
R232
R594
R258
JL190
8
JL209
E
JL130
C088
R272
JL292
Q606
C691
C671
JL179
JL193
JL187
JL185
JL212
R226
R221
Z901 JL513 JL163

R299
JL211
R164 R681 JL222 JL295 JL136 JL133

R255 R197
R260
JL298 JL296
C695
JL525
>005P
JL293
JL210
JL910
CN122
R170
R917
R998
JL164 R168 Z101 JL138 JL137

JL162
44 1
R533 JL297 R271
R151
45 176
R718
R103 R234 R111 C087 JL141

C672
R173JL285 JL161 JL143

TOP PANEL BOARD
R576
IC109 JL142
C986
R172 R293 JL144

R110 JL145
JL288 R292
JL269 R125
C513
C109 R116
CN1005
JL108 JL147
R291 R575 JL287
R123 C106
C102
(Page 43)
R503
JL230
R208 JL146
R132
R760
R762
H R102 JL268 JL300 JL231

R761
C126
JL139
R137
R188
X105 R285 JL524 R187 JL232

R186
JL107
JL140
24
C298
C297
C922
25
R176
JL520 JL523
C998
R829 JL155
IC914
R127
C127
R153 JL160 JL159 JL521

R154 C151
C699
R155 JL522
C696
C994
JL150
X104
R275
R156
R240
FB117
JL158
TH571
R177
R267
C997 JL255 C152

R178
R209
Z604
R179 JL214
R117
JL067
R826
JL218
R115
R180 JL165 88 133 L007

C029
JL213
C110 R104 89 132
C161
JL289
C047
JL256 R531 R276

R011
R010
NFC
JL276
R174
E JL168 R200 JL166 JL186 JL272 R280 JL219 R278
JL273
JL275
R196 X103 JL072 R032

R228
E Q107
JL208 R189 JL153
R233 R298
C041
JL167
C038
C149 R026
C162
Q108 JL188 JL152

JL116 R227
JL283 JL184 JL207 JL274

C049
JL191
R212
C028
C104
JL271 C299
I R160 Z102 6 2 6 2
R198
R214
R217
R100
R591
R220
R182
Q109 E
R128 JL195
CN105
IC009 CN105
R203
C107
R241
R238
R256
JL227
C130 C132 JL172 5 1 5 1

C019
R225
C014
A K JL178
JL148 JL105 C150
D102 R088
JL154
IC103
JL203
R013
R008 C006
R009 C004
JL197 C167 JL202 JL204

L004
C103 JL151 R014

C105
JL069
R518
R519
Z902
C050
JL241 JL169 L002

JL242 JL175 JL173 JL171
C016
JL004 JL106
1
JL502 JL176 JL170 2 16

2
JL112 JL071
CN102
JL506 CN113
JL501 JL174 JL199 1 15
JL201 JL114
JL113
10
JL198 JL196
9
DC01
R002
R003
C577 JL200 JL216 JL235 L001

C726
C015
>002P R063 JL215

JL102
C054
JL617
JL005 JL007
JL206 JL205
C003
C005
C083
JL217 JL109 Z603 L003

JL618 R012
E
19
J 2CH DAMP BOARD

R163 JL044 R087
18
JL048 JL049 Q009 BLUETOOTH MODULE

C059
JL194
R001
R578
C017
E
JL251
(SHAKE10/SHAKE30/
C013
JL006
IC001
R061
JL117
R062
R516 C093 JL013 R086

Q008
JL503
C026
C057
CN125
JL244
C084
JL248
C030
JL249
R525
C024
R515
C052
JL068 R024
CN1013
C037
C039
JL247 JL270 R025

JL045 JL012
JL504 JL009 C055 L008 L009
C010
JL008
(Page 40)
R007
R023
R006
JL047 L006
C053
JL115 JL010
JL014
JL104 C011 JL011 C091 C092 Z602
JL053 10 11 JL070
C044
2
JL103 CN001
>003P
JL054
1 9
(CHASSIS)
K Note 1: W h e n t h e c o m p l e t e M O T H E R B O A R D b o a r d
4CH DAMP BOARD is replaced, refer to “NOTE OF REPLACING
(HCDSHAKEX70) 11 MOTHERBOARD BOARD OR BLUETOOTH MODULE
CN1013
(Page 41) (CHASSIS) 1-981-670- (11) OR RC-S730 (WW)” on page 7.
2 16 CONNECT TO
CN113 REGULATOR, SWITCHING
1 15 (SSN-172AD) BOARD
Note 2: When the MS-476 board is defective, exchange the

(SHAKE10/SHAKE30/
~ AC IN
(NC) REGULATOR, SWITCHING
(SSN-171AD) BOARD
(HCDSHAKEX70) entire LOADING COMPLETE ASSY (T).
38 38
6-6. PRINTED WIRING BOARD - MOTHERBOARD Board (Conductor Side) - • See page 32 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
A
MOTHERBOARD BOARD
(CONDUCTOR SIDE)
Ú SHAKE10/SHAKE30
¹ HCDSHAKEX10/HCDSHAKEX30/HCDSHAKEX70
Q603, Q605,
B Q607
C1 B2 E2
JL907
Z909
E1 B1 C2 Z610
¹
C1013
¹ ¹
L900
C636
R937
IC1000
L601
L902
R1020
R1026
A
C1006
D900
C930
A/K
K
C638 R1019 R938
R1017 L901
L605
C932
C933
C931
C1003
R1030
R1000
R939
IC902
C935
R940
C1005
5 1
R657
R660
C934
Z104 6 20
R944
C1004 ¹ C664 R912 R911
C938
10 16
C631 C602 11 15
R312
C
R677
C941
C937
C936
R913
R914
IC903
X900
R943
R359
FB610 C943
C657
C650 C652
R319
C646
R685
R686
R353 Q302
R947
Ú
C626
C627
C645
R324 C376
C647
R945
E
¹
R857 R946
R671
E
R662
R752
R753
C306
C347
Q303 CL307 R751
R370
C352
C351 CL395 R669 R663
R381
CL301
C643 C641
R650
C348 R750
C346
C999 C660 C665 C711
CL302
C628
R689
CL311
C357
C344 C343
R651
C620
C621
Q605
R321
C350
Z906
C342
R362
C917
C339
R330 Z611
CL381 Q603
C340
C358
CL313
C325
C338
D
C326
C629
C330
C331
R328
Q607
R692
R700
R997
R438
R356 R357
C328
R435
R434
R348
R378
R439
R322
C316
R326
IC303
C373
R303
C979
L301
C319
C315 C336 R339

R347
R411
C407
C960 R664
C375
CL401 C372
R302
R350 C950
C321 CL337
28
CL402
IC401
C369
1
R352
CL403 CL408 CL412

CL404 JL355
R387
R343
R406 CL409 R346 R642 R915 R606 R621
FL601
CL321 C949 R644
CL411 R314
C409
22
7
R407CL405
IC601
C766
R600 R649 R916

R313 CL322
29
E
30
R616
CL407
CL410
C404
CL406 R607
21
8
R615
C462 C605 R608 C767
R451 Z914
R478 R465
C607
C465 R634
R310
14
C463
15
R646
IC602
R604
R456
C616
R318
R464 C302 R648

R612
R613
C303
R457
R466
R452 R636
R605
IC452
R602 R647
Q612
R639
R433
R051
R052
R610 R635
E
Q402
Q401
C466
R453
R498
C074
C075
C421
Z905 R424
C424
R054
R429
R626
R622
R420 CL414
C618
C614
F
E
CL413 Z908
CL415
R422
R431
R432
C613 C615
R421
IC603C625
C610
R425
R430
R427
R423
R426
R428
R053
R638
C634
C608
R617
R640
R609
R618
R652
R619
R820
R654
C635
C604
R614 C603 R655
C633
R620
R716
C632 C619
R656
R632
R643 C630 C624
R631 R711
IC604
C617 R629
R630
R237
R579
R580
G R239
R251
C501
C168
R590
IC609
R242 C679
R270 C673 C678 C669 R709
C133
R587
R119
R273
R205
C135
C503
C143
C674 C667
R300
R247
C153
R284 C670 C666

C111 R282 R720
C148
C137
C140
R501
R129
C142
C146 R723 R708

R133
R120
R222
IC106
C141
R719
IC102
R134
R589
R107
R131 R722
R135
R139
R598
R143
C154 C112
R502 C114 R817 Z907
C164 C155
C511
R140
C115
C156 R597
R112
C995
R289 R294 C157 Z103

R290 R286 R175
H
R683
R288 R287 C158 C118

C996 R978
C117 C281 C116

R504
C515
C159
R192 C160
C280 C120 R149

C138
R283
R253
C144
C282 C121
R250
R167
C123
C136
C122
FB101
R223 R166
R532
C147 R194
C134
C128 R577
R184
R113
R249
C131
R114
R244
R195
R252
R202
R574
R190
R146
R206
C129
R246
R245
R248
R145
R204
R236
R243 R144
R159
C165 R158 R157

R667 R191
R161
IC105
C166
C040
I
¹ Q572
C574
R1028
R491
E
R483
A
E
R487 R485
E
D572 A
D571
E
Q574
Q575 Q576 C101

R794
C100
Q104
C573
E
Z501 R571
IC008
E
R572 R520
Q571 E
Q103
R033
Q461
E
R109 R108
R035
R521
E
Q012
R066 R029
C068
IC004 IC006
C051
R065
J
E
R064
Q011
C085
C062
Q004
R017
C072
Z915
R792
R020
R019
R022
R080
K 11
1-981-670- (11)
Note: When the complete MOTHERBOARD board is replaced,
refer to “NOTE OF REPLACING MOTHERBOARD
BOARD OR BLUETOOTH MODULE OR RC-S730 (WW)”
on page 7.
39 39
6-7. PRINTED WIRING BOARD - 2CH DAMP Board (SHAKE10/SHAKE30/HCDSHAKEX10/HCDSHAKEX30) - • See page 32 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
2CH DAMP BOARD 2CH DAMP BOARD

A (SHAKE10/SHAKE30/HCDSHAKEX10/HCDSHAKEX30) (SHAKE10/SHAKE30/HCDSHAKEX10/HCDSHAKEX30)
(COMPONENT SIDE) (CONDUCTOR SIDE)
TB1002
SPEAKERS
IMPEDANCE USE
L R
+ – + –
(CHASSIS)
B (CHASSIS)
Q1002, Q1003,
Q1016, Q1018,
Q1019, Q1021
C1 B2E2
(CHASSIS)
C1127
C1189
C1125
C1114
C1115
C1123
C1122
CL1071
E1 B1C2
CL1070
CL1051
C1126
C1249
C1247
R1259 CL1053
R1022
C
D1030
C1049
A
C1016 C1147
C1248
K
A
R1194 CL1052
Q1030
R1168
E
R1027
C1041
R1024
C1017
C1145
C1036 C1002 R1174 R1177 CL1009
CL1010
C1250
R1185 R1282
R1047
Q1003
R1013 R1283
R1175 R1176
E Q1023
C1007
R1179
R1186
R1275 R1166
D1025
K A
A
D1029
R1178 R1221 CL1030 CL1074
K
CL1075
B E
CL1076 C1258 Q1020
C1254
D
C1238
C1149 CL1029
R1180
10
C1150
C1148
C1242 R1277
R1276
Q1029
E
E
R1181
CL1026
Q1026
R1278
CL1073
Q1021
R1182
CONNECT TO
R1169
R1164
(SSN-172AD) BOARD
CN1001
(SHAKE10/SHAKE30/
E HCDSHAKEX10/HCDSHAKEX30)
Q1019
CL1025
C1239
(SSN-171AD) BOARD
R1197
R1165
(HCDSHAKEX70)
CL1024
R1017 R1048 CL1072
D1006
C1146
D1003
CL1028
D1005 C1043 C1009 D1002 CL1027

C1014 C1047
1
F K A A K
C1015 C1048
Q1015
E
R1014 R1051
R1152
CL1063
R1151
R1153
C1137
C1138
D1021 K
L1003
L1001
G IC1005
C1139
C1001 C1005 C1039 C1035

CL1003 CL1008
H
C1006 CL1000 C1012 C1046 CL1005 C1040
Q1001
Q1004
Q1005
Q1000
TH1002 R1008 R1044

R1266
C1206
CL1001 CL1006
I DC FAN CL1004 CL1011

R1020
R1055
R1045
R1010
D1024
CL1002 CL1007
R1041
R1006
R1043
D1020
A
R1056
K C1154
K
C1240
R1054
R1040
Q1016 Q1014
R1042
A
R1021
R1007
D1007 C1203 D1004 R1066

K
D1023
C1228
R1011
K D1000
C1229
R1009
R1067
A/A
K A C1013 CL1034
K
CL1033
R1004
2 1
D1008 R1062
Q1002
R1057
R1063
R1064
R1039
IC1008
K
R1065 R1068
D1022
C1031 R1005 C1034
CL1039
K
4 3
D1009
R1037
26 17
A
C1202
C1050
A
D1001
A
27 16 C1033 C1201
R1033
CN1003
C1143
R1023
R1201
R1001
A
R1000
A
R1060
R1200
C1021R1059
A R1061
R1158 Q1018
R1038
CL1043
K
R1028
K
R1157
C1186
Q1027
32 C1220 CL1038
A
11
R1058
R1003
D1033
D1032
1
C1142
10 C1221
J
E
R1156
C1020
C1255
C1030
C1164
K
CL1049
K
1
C1163
R1207
R1036
21
20
C1022 C1019 C1018

R1289
>002P
IC1009
CL1048
C1188
R1029
C1187
R1246
R1288 C1032 CL1040

C1027 C1028
R1247
R1026
R1025
CL1047
MOTHERBOARD BOARD
IC1006
CL1037 CL1036
C1155 C1157
R1213
R1031
CN125 CL1046 CL1062

R1030
CN1013
(Page 38)
C1166
R1284
CL1045
40
CL1044
1
C1252
CL1068
R1285
18
Q1032
K CL1069
E
19
C1158 R1222
E
Q1031
R1287 CL1041
C1244
IC1007
C1165
(CHASSIS)
C1253
CL1061
C1156
R1286 C1251
CL1035
(CHASSIS) 11 11
1-981-997- (11) 1-981-997- (11)
40 40
6-8. PRINTED WIRING BOARD - 4CH DAMP Board (Component Side) (HCDSHAKEX70) - • See page 32 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
4CH DAMP BOARD

A (HCDSHAKEX70)
(COMPONENT SIDE)
TB1003 TB1000
LEFT SPEAKER RIGHT SPEAKER

IMPEDANCE USE IMPEDANCE USE
+ – + – + – + –
B (CHASSIS) (CHASSIS)
(CHASSIS)
Q1002, Q1003,
Q1008, Q1009,
Q1016, Q1018,
Q1019, Q1021 (CHASSIS) (CHASSIS)
C1 B2E2
E1 B1C2 R1188
R1189
R1190
D1030
C
R1022
C1108 C1075
B
R1187
R1195
Q1022
C1049 C1016 Q1025 E
A
R1194
K
R1103 R1225 DC FAN
3
C1100
R1027 R1098 C1152 C1151
C1041
C1095
C1017
Q1003
C1061 R1089
C1076
R1100
CN1011
C1036
1
C1002
R1173
R1123
R1024
Q1009
2
R1047 R1013
C1066
R1171
C1007
R1179
R1186
4
C1145
A R1185
Q1024 Q1023
E
K A D1025
R1221
D1029
E
R1178
R1181
R1277
K
CL1079
C1144
D CL1080
E B
C1149
C1263
Q1020
C1255
C1150
10
C1213
R1180
C1210
C1242
R1276
C1148
E
R1182 R1278
Q1029
E
Q1026
Q1021
R1280
CONNECT TO Q1030 E
E (SSN-172AD) BOARD R1279
CN1001
(SHAKE10/SHAKE30/
R1169
C1212
R1164
C1211
(SSN-171AD) BOARD Q1019
(HCDSHAKEX70)
R1165
R1197
C1146
C1068
F D1005 C1043 C1009
D1002 D1015
C1102
D1012
1
K A
A K K A A K
Q1015
E
R1153
R1152
R1151
A
C1138
C1137
D1021
K
L1001
L1003
L1008
L1006
G
IC1005
C1139
H
Q1011
Q1001
Q1010
Q1000
Q1007
Q1006
Q1005
Q1004
TH1002 TH1001
R1266
C1206
I
R1265
C1205
R1020 R1055
R1131
DC FAN
R1096
R1086
R1045
R1010
R1121
D1024
R1041
R1006
R1117
R1082
R1043
R1119
R1212
D1020
R1210
R1130
A
R1056
K A C1154
K
R1116
R1040
R1132
R1054
Q1016 Q1014
A
D1007 C1203 R1042 D1017 C1204 R1118

K
D1023
C1230
E
C1229
C1228
A/A
KD1014
R1080
D1001 R1004
K C1072
D1018 R1138
C1013 A K A A
K
D1008 R1062
R1057 R1133
IC1008
R1063
R1064
R1039 D1004 R1115

R1000
IC1010
R1001
R1140
R1139
K
2 1
D1022
R1005 C1034
D1010
K
K
R1114 C1231
C1093
C1109
D1000
D1019
D1009
26 17 26 17 4 3
A
R1158
A
C1050
A
27 16 16
27
R1077
R1076
CN1003
A
Q1018
A
C1021R1059
R1137
R1081
R1038
D1011K
K
R1290 D1035 K
Q1027 C1185
C1257
J R1206
A
C1186
R1061
R1037 R1007 11
R1134
R1135
32 32
R1058
11
R1003
R1079
C1080
A
D1034
C1091
E 10
1 1 10
R1258 R1083
R1257
K
R1207 E
C1079
R1292
C1020
C1090 C1089
R1113
R1021
R1253
Q1028
R1248
C1226
C1227
C1163
R1105
C1092
2
C1258
C1162
C1161
R1112
R1025
C1032 R1036
C1033
C1164
C1030
Q1002 R1101
R1251
R1289
C1081
R1097
R1291 C1077 Q1008

C1019 C1018
R1029
C1022
R1026 C1078
R1102
>003P
R1247
R1246
R1252
C1031
C1028
IC1006
C1027 C1086 C1087

R1031
C1155 C1157
40 21
MOTHERBOARD BOARD
R1106
CN1013
R1030
R1213
IC1009
CN125
C1166
R1285
R1107
R1215
C1221
(Page 38)
1 20
C1220
C1248 C1249
K
C1253
C1250
C1187 R1157
18
R1286
Q1033
19
R1156
C1158 R1222
E
Q1032
R1288
IC1007
C1188
C1165
C1254
C1143
C1142
(CHASSIS)
C1156
R1287
(CHASSIS) 11
1-981-968- (11)
41 41
6-9. PRINTED WIRING BOARD - 4CH DAMP Board (Conductor Side) (HCDSHAKEX70) - • See page 32 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
A 4CH DAMP BOARD

(HCDSHAKEX70)
(CONDUCTOR SIDE)
CL1070
B
C1123
C1122
C1128
C1129
CL1056
C1120
C1194
C1121
C1116
C1127
C1189
C1118
C1119
C1125
C1114
C1115
CL1060
CL1071
C1126
CL1058 CL1051
CL1055
CL1030 CL1057 CL1054 CL1052
C1147
CL1059
CL1031 CL1053
CL1021
C R1174 R1177 CL1022 CL1010
CL1009
R1175 R1176
CL1032 R1275 R1166
CL1078
CL1074 CL1029
D CL1075
CL1026
CL1073
R1168
CL1025
CL1024
E CL1072 CL1077
R1093 R1124 R1017 R1048 CL1076

D1013
D1016
D1006
D1003
CL1028
C1014 CL1027
C1073
C1047
C1106
F R1090
C1074
R1127
C1107
R1014
C1015
R1051
C1048
CL1063
C1060 C1098 C1001 C1005 C1039 C1035

CL1015 C1064 CL1020 C1094 CL1003 CL1008
C1065 CL1012 C1071 C1105 CL1017 C1099 C1006 CL1000 C1012 C1046 CL1005 C1040
H
R1084 R1120 R1008 R1044

CL1001
CL1013 CL1018 CL1006
CL1016 CL1023 CL1004 CL1011
CL1014 CL1019 CL1002 CL1007

I C1241 C1240
R1142
R1087
R1066
R1011
R1009
R1067
R1085
R1141 R1143
R1065 R1068
CL1034
R1144
C1199 C1201 C1202
R1033
C1200
R1023
R1201
R1109
R1199
R1060
R1200
R1099
CL1033 R1136
R1198
R1104 R1028
C1251
A
D1033
D1032
CL1040
K
CL1049
CL1048
J CL1038
CL1047
CL1037
CL1036
CL1062
CL1068 CL1045
CL1044
CL1046
CL1043 CL1039
CL1041
C1252 CL1069
C1244
K CL1061
CL1035
11
1-981-968- (11)
42 42
6-10. PRINTED WIRING BOARD - TOP PANEL Board - • See page 32 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
A
FL BOARD LED DRIVER BOARD MOTHERBOARD BOARD
CN2006 CN6003 CN451
TOP PANEL BOARD (Page 45) (Page 48) (Page 38)
Ì HCDSHAKEX70
SHAKE10/SHAKE30/HCDSHAKEX10/HCDSHAKEX30 >006P >007P >004P
B
JR1525 CL168 CL050
CL051
CL073
D1013
CL242
CN1006 CL175 CL169
CL049
CN1002 JR 11 1
JR1653
7 1
JR1649 CN1004
JR
S1026 1 6
CL067 JR
10 2 CL176
6 2
CL172 DJ EFFECT R1084 CL157 6
LP1002
JR1508 FUNCTION C1025
CL078 CL077
CL071 R1042 CL174 CL171 JR CN1001 D1006
CL069 JR S1001 CL173 CL140 5 7
JR1514
JR1505
JR1504
JR1654
CL165
JR1646
JR1648
JR1513 CL074 JR1509 CL052
JR1647
JR1515
JR
JR
1 4
JR
JR
DJ EFFECT CL054
JR
CL079
JR
JR1571
JR1565
JR CL241
JR
JR
R1087
R1086
GUITAR
JR
JR
JR1651
JR1652
CL076 JR1560
JR1656
JR1650
CL010 S1015 CL153 S1002 CL156
JR
JR
JR1667
R1149
JR
R1041
1
JR
JR
CL075
JR1511
C VOCAL
2
A
MIC JR JR1570 JR1566 JR1561 JR1506 CL158 CL159
D1008
JR
ECHO FADER JR1668 CL177 JR JR
JR1669 JR JR CL025
JR1500
JR
JR1501
CL011 CL139
JR1615
JR1572 JR1567 JR1562
JR
JR1614
D1004
D1003
JR
JR1672 JR D1009 R1091 D1011
JR
CL146 R1044 JR JR JR JR
JR1516
JR LP1001
D1005
JR
JR
CL070 JR1563 JR1507

CL072 CL058 JR1670 JR C1013
JR JR
CN1005
JR1617
JR1616
JR1517 R1043 JR CL178 JR1573 JR1568 C1012
JR
R1080 W003
JR1673
JR1512
JR1658
JR1645
JR1644
JR1636
JR CL145 CL130 JR1666 JR C1011
>005P
JR1518
JR
JR JR1662
JR
JR
JR
JR
JR JR JR
JR1581
JR1569
JR1579
JR1580
CL068 CL066 JR JR1564 S1017
JR1671
JR1532 JR1502
JR
JR
JR1618 C1023
JR
JR
EN1002
JR
JR
JR1519
JR1674
JR MEGA BASS
JR1522
JR
JR1521
CL062 MIC/GUITAR LEVEL
JR
JR
MOTHERBOARD
JR
CL064
JR
C1009
JR1643
JR1642
JR1663
S1032
JR1582
JR1661
S1031
JR
JR1675
JR
JR
JR
JR1586
BOARD
JR1584
JR1583
JR
JR
JR
JR1585
CL060 JR1520 DJ EFFECT
JR
JR
DJ EFFECT
JR
JR
D CN122
DJ OFF CL096 CL160 R1089 FLANGER
JR1524
JR1523
JR1697
JR1665
JR1526 R1011
CL056
JR1659
JR1620
JR
JR
JR
JR1619
JR
JR JR1655
JR1640
JR
JR1533
JR1534
JR1637
JR1641
JR
JR
JR1660
(Page 38)
24
JR C1014 R1021 CL161
JR
JR
JR
JR
JR
JR
25
JR1588
JR1587
Ì
JR1591
JR1590
JR1589
R1143
R1144
R1022
JR
JR
R1015
R1140
CL055 EN1001 R1020
JR
JR
JR
C1028 CL097
CL057 R1003
JR1699
JR1698
JR1657
VOLUME/DJ CONTROL
CL059 CL034 CL036 CL038 CL040
JR
JR
JR
CL061 D1010 R1001 JR1592 D1012
D1007
JR1638
JR1639
CL065 CL083 JR1621 CL037 JR
C1029
C1062
C1015
CL039 CL030
JR
JR
R1090 JR CL035
C1007
C1006
C1008
CL063
C1003
R1012
JR1696
JR1531
R1040
JR
JR1539
JR1622
JR
JR R1148 CL167
JR1678
JR1677
JR1676
CL084 CL170 JR1593 CL155
JR
JR
JR
JR
JR
JR1664 JR
JR1510
JR JR1596 JR CL138
JR JR
JR
JR1695 CL031 JR1595 JR1594 CL041
C1043
C1050
C1049
C1056
R1130
R1128
CL032
E CL137 R1039
JR1598
JR1530
JR1599
JR1597
S1016
JR
JR
JR
JR
CL222 CL224 CL226 CL229 CL033 12 1 REC TO USB
C1004
CL219 CL228
R1132
IC1001 CL042
S1018
CL166
JR1602
13 24
R1038
JR
CL221 CL223 CL225 CL227 CL024 PAIRING
JR1601
R1146
JR1600
C1052
CL015 CL016 CL023
JR
JR
D1014
D1015
JR1624 CL022 BLUETOOTH
R1010
CL014
R1013
JR1538 R1122 CL220 12 1 JR
JR1606 JR1605 JR1604
JR
IC1002
JR JR1626
JR JR JR
C1041
JR1527
JR1635 CL208 13 24 JR1603

S1003 S1004
JR
JR1625
JR
R1147
R1116
JR
C1058
C1057
CL218
C1061
C1067
C1066
C1065
C1064
C1063
C1059
JR
C1039 CL210 CL020
CL213 CL215
JR1535 S1030 R1102 R1145 CL217
JR1679 CL209 CL017 CL018 JR1607 CL021 S1028
JR CL211 CL214
DJ EFFECT JR
R1139
R1138
JR DJ EFFECT
R1137
F CL147 JR1634
R1134
R1068 SAMPLER JR CL216 Ì ISOLATOR
CL154 CL212
R1136
R1135
R1105
R1104
R1106
R1131
CL230 CL019 Ì
S1020
R1121
R1110
CL131 R1133 JR1612 R1047 CL132 CL136

R1036 CL148 JR JR1610 JR1608 PARTY
JR1627
JR JR LIGHT
JR1633 JR
JR1628
JR JR S1027
R1118
JR
JR1613 JR JR R1037 CL135
FOOTBALL
R1109 JR1611 JR1609
JR1632
JR1629
R1072 R1048
JR1631
JR
JR
JR
CL142 S1019
R1046
LIGHT
JR1630
JR1680
R1108
MODE
JR1529
JR
JR1528
JR S1009
R1070
R1071
JR
JR
JR1686 JR1685 S1029

G JR
JR1681
JR JR SOUND
FIELD
R1073
FIESTA CL144 R1045
CL150 CL152 R1049

CL207
S1025 S1022
PARTY
R1069 CHAIN
S1006 JR1691 JR1688 CL151 S1007 CL141 CL143
R1088
JR JR CL133 CL134
TUNING + JR1689 JR1690 TUNING –
JR1687 JR1684
JR1692
JR JR R1076
JR
JR JR
S1005 CL235
CL240 JR JR1503 S1008 S1021 S1014
CL089
CL236
CL149 CL239 CL237 CL088 CL087

CL095
JR1694
JR1683
JR1693
CL233 CL232 CL086 ENTER

JR
JR
JR
JR1536
CL234 CL238 CL093

CL085
H JR1537
JR
Ì JR
CL092 CL231
11 NO1007 1 10 NO1003 3 1 NO1008
11
3 1
1-981-969- (11)
I >008P >009P >010P >011P

HI-RGB RIGHT HI-RGB RIGHT LED PC BO HI-RGB RIGHT HI-RGB RIGHT LED PC BO
BOARD BOARD BOARD BOARD
(HCDSHAKEX70) (SHAKE10/SHAKE30/ (HCDSHAKEX70) (SHAKE10/SHAKE30/
CN003 HCDSHAKEX10/HCDSHAKEX30) CN005 HCDSHAKEX10/HCDSHAKEX30)
(Page 50) CN003 (Page 50) CN007
(Page 50) (Page 50)
J
43 43
6-11. SCHEMATIC DIAGRAM - TOP PANEL Board - • See page 52 for IC Block Diagram
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
A TOP PANEL BOARD

R1089 R1088 R1076 R1048 R1037 R1038 R1039 R1040 R1041 R1042 R1043 R1044 R1080
CL160 33k CL161 22k CL134 15k CL133 10k CL135 6.8k CL136 4.7k CL137 3.3k CL138 2.2k CL139 1.5k CL140 1.5k CL130 1k CL145 680 CL146 0
S1032
S1031 S1021 S1020 S1019 S1018 S1001 S1002 S1015
S1022 S1016 S1017 S1026 S1014
DJ EFFECT DJ EFFECT
x PARTY LIGHT PAIRING DJ EFFECT DJ EFFECT VOCAL MIC
DJ OFF N REC TO USB MEGA BASS 1
FLANGER LIGHT MODE BLUETOOTH FUNCTION GUITAR FADER ECHO
B R1047 R1046 R1045 R1049 R1073 R1072 R1071 R1070 R1069 R1068 R1036
CL132 22k CL142 15k CL143 10k CL144 6.8k CL141 4.7k CL152 3.3k CL131 2.2k CL151 1.5k CL150 1.5k CL149 1k CL148 680 CL147
S1028 S1025 S1029 S1007 S1006

S1027 S1009 S1008 S1030 S1005 S1004 S1003
DJ EFFECT PARTY SOUND DJ EFFECT
FOOTBALL FIESTA ENTER TUNING - TUNING + Z
ISOLATOR CHAIN FIELD SAMPLER
. > - +
0.01u
0.01u
0.01u
0.01u
0.01u
0.01u
0.01u
0.01u
0.01u
0.01u
0.01u
0.01u
0.01u
0.01u
*1 R1137, R1138, R1139
22 (SHAKE10/SHAKE30/
C1029
C1015
C1006
C1008
C1007
C1062
C1067
C1066
C1065
C1064
C1063
C1057
C1058
C1059
R1140 47 (HCDSHAKEX70)
47
NO1003
10P HCDSHAKEX70
CL031 3.3 CL014 R1139 22 *1 CL239
OUT7 OUT8 10 BLUE-3
CN1005 CL032 3.9 12 13 3.1 CL015 R1138 22 *1 CL238
25P OUT6 OUT9 9 GREEN-3
CL033 0 11 14 1.8 CL016 R1137 22 *1 CL237
CL057 OUT5 OUT10 8 RED-3
D AD_KEY1 25
CL058
CL030 R1015 22 CL034 1.9 10
OUT4 OUT11
15 3.4 CL017 R1136 47 CL089
7 BLUE-2 HI-RGB RIGHT
AD_KEY0 24 CL177 CL035 9 16 CL018 CL088
R1135 47
BOARD
R1091 47 3 1.9
CL059 OUT3 IC1001 OUT12 6 GREEN-2
DGND 23 CL025 R1020 68 CL036 0 8 17 3.3 CL019 R1105 47 CL236
CL060 TC62D723FNG
MIC_VOLUME 22
CL061 CL096 R1021 22 R1143 22 CL037 3.8 7
OUT2
IC1001
OUT13
18 3.3 CL020 R1104 47 CL087
5 RED-2
(HCDSHAKEX70)
OUT1 OUT14 4 BLUE-1
RGB_SCLK 21
CL062 R1011 CL055 CL097 R1022 22 R1144 22 CL038 8 6
OUT0
LED DRIVER
OUT15
19 3.2 CL021 R1106 47 CL086
3 GREEN-1
CN005
1L0352W32B0MIT01
RGB_TRANS 20 10k
HL-364V620MZ-T
HL-364B460MZ-T
R1003 100 CL040 5 20 1.7 CL022
HL-364W650MZ-T
8 HCDSHAKEX70 R1013 100
HL-364W650MZ-T
CL063 TRANS PWMCLK
RGB_PWM 19 CL056 C1014 R1001 100 CL039 0 4 21 0 CL023 CL093
D1013
D1006
D1007
CL064 0.001u
D1015
SCK SOUT 1 RED-1
D1014
RGB_SD 18 EN1001 R1012 100 CL041 0 3 22 1.1 CL024
CL065 SIN REXT
E D+3.3V 17
MASTER-VOL 16
CL066
VOLUME/DJ
CONTROL
0 2
GND VDD
23 3.3 CL042 R1010 NO1008 SHAKE10/SHAKE30/
C1003 1 24 820 3P HCDSHAKEX10/HCDSHAKEX30
CL067 100p
POWER KEY 15
25 3 BAR_LED_CENTER
MOTHERBOARD SIRCS 14
CL068
CL178 CL154 CL155 C1004 0.22u
HI-RGB RIGHT LED
CL069 2 BAR_LED_RIGHT
R1090
BOARD E+3.3V 13 10k
CL083
1 BAR_LED_LEFT PC BO BOARD
HL-364W650MZ-T
HL-364W650MZ-T
CL070
CN122 DGND 12
CL071 CL084 C1028 (SHAKE10/SHAKE30/
D1010
D1012
FL_LATCH 11 0.001u C1041 C1039
C1052 C1049 C1043 C1050
FL_SOUT 10
CL072 EN1002 0.01u 0.01u 0.01u 0.01u
0.01u 0.01u
HCDSHAKEX10/
CL165 MIC/GUITAR R1116 R1146 R1122 R1108
F FL_CLK 9 LEVEL 68 68 10.4 CL208 120 120 HCDSHAKEX30)
OUT7 OUT8
LED_GND 8
R1118 R1147
CL219 9.1 12
OUT6 OUT9
13 1.9 CL209
R1145 R1102
CN007
LED_GND 7 68 68
CL011 68 68 CL220 1.9 11 14 9.2 CL210
HL-364W650MZ-T
HL-364W650MZ-T
LED_GND 6 OUT5 OUT10
CL221 4.2 10 15 1.9 CL211
LED_GND 5 OUT4 OUT11
D1009
D1011
R1109 R1121 CL222 0.8 9 IC1002 16 1.9 CL212
M+5.2V 4 OUT3 OUT12
120 120 CL223 0.8 8 TC62D723FNG 17 1.9 CL213
R1149 OUT2 OUT13
M+5.2V 3
CL010 0
R1110 R1148
CL224 3.7 7
OUT1
IC1002OUT14
18 1.9 CL214
M+5.2V 2 68 68 CL225 LED DRIVER
CL153 1.9 6 19 1.9 CL215 R1133
M+13V 1 OUT0 OUT15
G R1130 100 CL226 9 5
TRANS PWMCLK
20 1.6 CL216 100
CN1006 R1128 100 CL228 0 4 21 0 CL217
11P SCK SOUT
CL175 R1132 100 CL227 0 3 22 1.1 CL218
RGB_PWM 1 SIN REXT
CL176 CL229 0 2 23 3.3 CL230 R1131 R1134
RGB_SOUT 2 C1056 GND VDD
CL172 1 24 560 0
100p
RGB_SCLK 3 NO1007
CL171 25
RGB_TRANS 4 11P
LED DRIVER D+3.3V 5

CL169 C1061 0.22u CL232
1 E+3.3V HI-RGB RIGHT LED
CL170 CL231
H BOARD LED_GND 6
CL168 CL233
2 DGND PC BO BOARD
3 SIRCS
CN6003
M+13V 7
CL174 CL234
4 HI-BLUE2
(SHAKE10/SHAKE30/
LED_GND 8
LED_GND 9
CL167 CL235
5 HI-GREEN2 HCDSHAKEX10/
CL166 CL085
M+5.2V 10
CL173 CL207
6 HI-RED2 HCDSHAKEX30)
7 HI-BLUE1
M+5.2V 11
CL095
8 HI-GREEN1
HI-RGB RIGHT
CL092
9 HI-RED1 BOARD
CL241
10 M+5.2V (HCDSHAKEX70)
I CL240
11 M+13.5V
CN003
CL079
1 NC
CL078
2 FL_LAT
CL077
3 FL_SDO
CL076
4 FL_CLK
FL BOARD
CL075
5 D+3.3V CN2006
CL074
J CL073
6
7
DGND
FL+13V
CN1002
7P
CL156 VBUS CN1001
R1086 0 CL158 D-
REC/PLAY
R1087 0 CL159 D+
CN1004
6P GND 5V 1A
CL049 C1009
K USB +5V 6
CL050 C1025
0.1u
D1008 D1003 D1004
BAV99-215 BAV99-215
100u
6.3V
C1023
22u
C1012
10u
C1013
0.01u
MOTHERBOARD D- 5
CL051
DZ2J068M0L
D+ 4
BOARD USB GND 3
CL052
D1005
CN451 NC 2
CL242 R1084
0 C1011 BAV99-215
SHIELD 1 0.1u
CL157
W003
CL054
44 44
6-12. PRINTED WIRING BOARD - FL Board - • See page 32 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
FL BOARD
TOP PANEL BOARD
B CN1002
(Page 43)
>006P
CL2124 CL5170 IC1003

C CN2006
1 3 2
7 1
C2127
R2134
R2146
R2147
R2148
R2149
R2150
R2135
R2136
R2137
R2138
6 2
C2111
R2141
CL2127
R2140
R2142
R2143
R2144
C2108
C2109
C2105
CL2129 CL2125
CL2128
JR
CL2130 C2078
JR2011
D
JR2014
JR2012 C2073
JR
JR
A K
D2015
A
C2068
C2070
C2104
R2094
D2010
C2074 C2069 R2098
R2099
K
Q2006 D2008 D2009 ND2001
VACUUM FLUORESCENT R2100
A/K A/K
E A K A K
R2095 DISPLAY CL3163 CL2138 R2101
CL2143 R2102
C2077 R2085 CL3166
R2084
CL3155 C2066
C2075
CL2132 R2111
C2126
CL3165
CL3148
CL2142
CL3156
CL3154
CL3152
CL3161
CL3158
CL3159
CL2126 CL2136
CL3150
CL3164
CL2137
C2125
R2097
C2076
CL2134
CL2139 CL2141
R2096
CL3147
CL3149
R2086
CL3151
CL3160
CL3153
CL3157
CL3146
CL2135 CL2140
CL3145 C2122
F CL2144
JR2010
CL2133
JR
CL2131 CL3162
CL3167 CL3169
CL3168 11
1-981-972- (11)
45 45
6-13. PRINTED WIRING BOARD - MIC Board - • See page 32 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
MIC BOARD
J2204
J2203 MIC2/
B MIC1 GUITAR
CL2289
C2269
C2268
A/K A/K
D A K
CL2288
A K
D2223 D2222
CL2286 CL2283 JR2200

CL2290 CL2291 JR
C2265
R2531
E
C2267
R2529
CL2292 Q2203 CL2293 R2534
FB006
R2526
R2528
C2266
R2527
CL2276 CL2275 R2533
JR2210
E
JR2206
JR
Q2205 JR
CL3002 R2532
1
R2506
FB007
C2133
R3003
JR2205
R2513
E CL2285
R2523
JR
JR2203
CL2274 C2245
JR2207
JR
C2263
3
JR
C2246 JR2209 JR2202
F R2522
R2525
JR
>001P
C2264
CL3003 JR JR2208 JR
C2251 C2260 R3004
R2524
R2515
NO1102
C2261
MOTHERBOARD BOARD
C3001
CL2273 CL2270
R3001
C2243
CN601
C2134
C2262
IC2101
14
C2253
(Page 38)
1
CL2272
R3005
CL2271
C2244
IC2202
5
4
8
R2505 C2252
8
R2510
R2507
R2517
C2254
R2509
1
G R2512 JR2204 R2518
R3002
C2250
C2258
JR
R2516
K
A
R2508 R2514
JR2201
R2520
R2511
D2218
D2220
CL2280 R2521
JR
A
K
11
H 1-981-973- (11)
46 46
6-14. SCHEMATIC DIAGRAM - MIC Board -
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
MIC BOARD
68k
C2265 6
2.2u R2531 CL2290
R2533 7
R3004
CL2283 50V CL2286 0 1k 2
CL2292 1 J2203
5
4 MIC1
2.2k
3
C2134 C3001 R2515
10u 0.47u 0 C2267 R2529
50V 50V 1500p 22k
R3005
R3002
C 0
8.9 4.4 1.9 0 4.4 4.5 4.5 4.4 C2268
R2526 R3003 D2222 0.001u
8 9 10 11 12 13 14 R2513 1 2 3 4 100k 10k
4.4 S BAV99-215
100k
OUT1
-IN1
+IN1
VEE
NO1102 R2524 C2262
8P R2505 10k 0.1u Q2205
4.4
0 C2251 C2253 LTC014EUBFS8TL
220u IC2101 Bias Detector IC2202
A+9V 8 0.1u NJM2783V (TE2) BA4558F MIC DETECT
CL2271 10V CL2270 CL3002 0
MIC1 7
CL2272 IC2101 IC2202 8.9 Q2203
MOTHERBOARD MIC_GND 6 CL2289
+
RHK005N03T146
+
CL3003 C2261 MIC AMP – –

MIC AMP
D MIC2_GUITAR_SIGNAL 5 R2525
220u
C2263 R2516 MIC DETECT C2133
BOARD
8.9
CL2273 10k 0.1u 39k 0.01u
OUT2
10V
+IN2
VCC
MIC_DET1 4
-IN2
CL2274 R2511 R2510
C2245 0.1u
CN601 MIC_DET2 3
CL2275
C2246 100k 100k
7 6 5 4 3 2 1
CL2288
R2506 0.1u 8 7 6 5
0 0 4.5 4.4 4.4 4.4 4.4 4.5 8.9 4.4 4.4 4.4 D2223
MODE_SEL 1 BAV99-215
CL2276
FB006 FB007 C2254 R2518
0uH 0uH 220p C2269
0 0.001u
R2514 D2220
C2250 DA2J10100L C2264
18k R2523 R2527 6
C2244 C2243 2.2u CL2291
E R2508
0
2.2u
50V
R2517
68k 1u 220p 100k 2.2M 50V CL2285
R2532
0
R2534
1k CL2293
7
2
J2204
1 MIC2/
5 GUITAR
R3001 R2522 4
CL2280 68k 1.2k 3
R2512 R2520 C2266 R2528

C2260
18k R2521 1u 0 1500p 2.2M
D2218 33k 50V
DA2J10100L
C2258
C2252 R2509 3.3u
F R2507
0
2.2u
50V
39k 50V
47 47
6-15. PRINTED WIRING BOARD - LED DRIVER Board - • See page 32 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
LED DRIVER BOARD
PARTY LIGHT PARTY LIGHT

B R L
CL6053
A6002 CN6002 CN6001 A6001

C 1 8 1 8
CL6073
CL6072 JR019
CL6060
JR047
JR
CL6055 JR JR008
JR
CL6027 CL6007
C6058
JR028
CL6005 R6005 CL6006

JR
CL6054
R6045
R6044
R6043
R6042
R6028
R6030
R6029
R6031
CL6004
R6007
R6006
R6008
JR029
CL6059 R6038 CL6056 R6019 CL6008
JR
JR048
JR018
JR
D CL6026 CL6009
C6016
C6015
C6010
CL6032 CL6057 JR R6020 CL6024
JR020
C6060
C6046
C6042
C6040
C6045
C6044
C6039
C6038
C6041
R6023
C6012
C6009
C6008
C6002
JR
JR049
R6021
R6022
JR027
JR007
CL6038 CL6039
JR
JR013 JR023 JR
JR
CL6030 JR050
JR JR CL6003
CL6037 R6040
JR040
JR002
CL6001 JR
JR
JR
CL6033 CL6036 JR JR033
CL6041 CL6040 JR010
CL6029 JR
E CL6034
JR014
R6039
C6032
R6046
CL6035 CL6064 JR021
C6013
C6017
JR
CL6031 12 1
IC6001 JR
C6004
12 1
R6034 CL6002 CL6063
13 24 CL6010
IC6002 R6011 CL6028 CL6025
CL6022
CL6023
C6034
R6036
CL6012 CL6011
13 24 CL6050 R6001 CL6013
R6015 CL6021
R6017
R6016
CL6020
F CL6043 R6002 JR
R6013
CL6065 CL6069 JR JR
JR026
CL6046
CL6051 CL6052 R6003 CL6014 C6022 JR015
JR
CL6042 JR012 JR032
CL6044 CL6047 C6023 R6004 C6021
C6020
C6006
C6005
C6019
C6007
JR JR CL6070
JR
JR011 JR017 JR016 R6009 CL6015 R6050 CL6062
CL6016 CL6018
JR030
R6010
JR024
JR022
CL6066
C6050
C6049
C6048
C6047
C6037
C6036
C6035
JR
JR
JR
CL6048
C6011 JR
G CL6017
JR025
CL6049 JR006
JR001
2 10
JR
JR
CL6045 CN6003 CL6061

CL6068 CL6019
R6018
JR003
1 11
R6024
R6025
R6026
R6027
R6033
R6053
JR
R6041
JR
JR005
JR004
CL6067
JR
R6032 JR009 JR
CL6058
CL6071 11
H 1-981-985- (11)
>007P
TOP PANEL BOARD
CN1006
(Page 43)
I
48 48
6-16. PRINTED WIRING BOARD - SKY BLUE Board (SHAKE10/SHAKE30/HCDSHAKEX10/HCDSHAKEX30) - • See page 32 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
SKY BLUE BOARD

(SHAKE10/SHAKE30/HCDSHAKEX10/HCDSHAKEX30)
B
D3501 D3502 D3503

CL3502
CL3503
R3501
C CL3504 CL3501
NO3501
4 1 11
1-982-270- (11)
>012P
D HI-RGB RIGHT LED
PC BO BOARD
(SHAKE10/SHAKE30/
CN006
(Page 50)
6-17. PRINTED WIRING BOARD - BAR CENTER Board (HCDSHAKEX70) - • See page 32 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
A
BAR CENTER BOARD
(HCDSHAKEX70)
HI-RGB RIGHT BOARD
(HCDSHAKEX70)
CN002
B (Page 50)
>013P
D101, D102, D103

12 11
GK
RK
BK
CN103
JR104
10 1
C
JR103
CL127 CL126
JR
JR
CL109 CL125
JR JR
GA
RA
JR101
BA
JR102 CL111 CL124 JR106

JR
CL110 CL113
CL112
CL123
RA RK
D101 D102 D103
GA GK
D
BA BK 11
1-982-269- (11)
49 49
6-18. PRINTED WIRING BOARD - HI-RGB RIGHT LED PC BO Board 6-19. PRINTED WIRING BOARD - HI-RGB RIGHT Board (HCDSHAKEX70) -
(SHAKE10/SHAKE30/HCDSHAKEX10/HCDSHAKEX30) - • See page 32 for Circuit Boards Location. • : Uses unleaded solder.
• See page 32 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
A HI-RGB RIGHT LED PC BO BOARD A HI-RGB RIGHT BOARD

TOP PANEL TOP PANEL
BOARD BOARD
NO1008 NO1003
B (Page 43) B
(Page 43)
>011P TOP PANEL BOARD >010P TOP PANEL BOARD
NO1007 NO1007
(Page 43) (Page 43)
D001, D002
CN007
>009P D001, D002
>008P
GK
RK
BK
GK
RK
BK
5 4
11 10
C 3 1
C
9 CN005 1
GA
RA
BA
GA
RA
BA
13 12
13 12
CL003 11 CN003 1
CL003 11 CN003 1
RA RK D002 D001 RA RK D002 D001
JR002
JR009
CL026
JR002
JR009
JR
JR
CL026
JR
JR
GA GK
CL025 CL027 GA GK
CL025 CL027
D BA BK JR006
D
JR004
BA BK JR006
JR003
CL032
JR004
JR
JR003
CL001 CL032
JR001
JR
CL001
JR001
CL009 CL029
CL033 CL009 CL029
JR
CL038 CL006
JR
CL005 CL028 CL033
JR
CL038 CL006
JR
CL005 CL028
JR
JR
CL007 CL004
JR
JR008 CL030 CL031 JR
CL007 CL004
CL008 JR008 CL030 CL031
CL011 CL008
CL011
CL010
1 4 1 7 CL010
CN004
E 5 6 8 9
E 1 CN002 10 1 CN004 7
CN006 11 11 12 8 9
11
1-982-079- (11) 1-982-079- (11)
>012P >014P >013P >015P

F F
SKY BLUE HI-RGB LEFT BAR CENTER BOARD HI-RGB LEFT BOARD
BOARD BOARD (HCDSHAKEX70) CN201
(SHAKE10/SHAKE30/ CN201 CN103 (Page 51)
HCDSHAKEX10/HCDSHAKEX30) (Page 51) (Page 49)
NO3501
(Page 49)
G G
H H
I I
J J
K K
50 50
6-20. PRINTED WIRING BOARD - HI-RGB LEFT Board - 6-22. SCHEMATIC DIAGRAM - IR Board -
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
A A
HI-RGB LEFT BOARD
IR BOARD
HI-RGB RIGHT LED PC BO BOARD
HI-RGB RIGHT BOARD (SHAKE10/SHAKE30/HCDSHAKEX10/
(HCDSHAKEX70) HCDSHAKEX30) NO1223
B CN004 CN004 B 4P R2502
0
4
(Page 50) (Page 50) HI-RGB LEFT SIRCS 1
C2502
CL2502 1
VO IC010
220p 2
>015P >014P BOARD DGND 3
CL4511 GND PNA4823M03S0
CN202 EVER+3.3V 4
CL4512
C2501
0.22u
CL2501 3
VCC IC010
REMOTE CONTROL
>016P R2501 5 SIGNAL RECEIVER
22
IR BOARD
NO1223
C D201, D202 (Page 51) C
GK
RK
BK
9 8 5 4
7 CN201 1 CN202
3 1
CL201
GA
RA
BA
JR200
JR
CL205 CL204
CL206 CL202 CL203

D RA RK
D
GA GK CL207
BA BK
D202 D201
11
1-982-081- (11)
E E
6-21. PRINTED WIRING BOARD - IR Board -

1 2 3 4 5 6 7 8
IR BOARD
5 4
IC010
C2502
CL2502
C CL4511
CL2501
R2501
C2501
R2502
NO1223
1 3 4 CL4512
D 11
1-981-974- (11)
>016P
HI-RGB LEFT BOARD
E CN202
(Page 51)
51 51
• IC Block Diagram
IC1001, IC1002 TC62D723FNG (TOP PANEL BOARD)
GND 1
16 25 GND
SIN 2 Error detection result Output open/short detection circuit POR
data register 16 circuit 24 VDD
SCK 3
TRANS 4 Constant current output circuit Reference

voltage
OUT0 5
Output delay circuit 23 REXT
OUT1 6 16
8-bit
0-bit 15-bit
TSD DAC
Output ON/OFF setting data register circuit
8
Comparator
Comparator
Comparator
PWM
OUT2 7 countor
OUT3 8
OUT4 9 16 16 16
OUT5 10 PWM data registor
16-bit 16-bit Registor 3 16-bit
OUT6 11 POD PWM Data PWM Data PWM Data
circuit for OUT0 for OUT1
(for output)
for OUT15
OUT7 12 16 16 16 16-bit x 2
State setting
16-bit 16-bit Registor 2 16-bit register
OUT8 13 16 PWM Data 16 PWM Data 16 PWM Data
for OUT0 for OUT1 (for synchronous) for OUT15
OUT9 14 16 16 16
16-bit 16-bit 16-bit
OUT10 15 Registor 1 PWM Data
PWM Data PWM Data
16 for OUT0 for OUT1 for OUT15
16
OUT11 16
16 16 16
OUT12 17 Command
control Data transfer control circuit
OUT13 18 circuit
OUT14 19 16 16
0-bit 15-bit
16-bit shift registor
SOUT
selection 22 SOUT
circuit
F/F
20 21
PWMCLK
OUT15
52 52
SECTION 7
EXPLODED VIEWS
Note:
• The mechanical parts with no reference • Abbreviation
number in the exploded views are not sup- AR : Argentina model The components identified by mark 9 con-
plied. AUS : Australian model tain confidential information.
• Items marked “*” are not stocked since CND : Canadian model Strictly follow the instructions whenever the
they are seldom required for routine E4 : African model components are repaired and/or replaced.
service. EA : Saudi Arabia model Les composants identifiés par la marque
Some delay should be anticipated LA9 : Latin-American model 9 contiennent des informations confiden-
when ordering these items. tielles.
The components identified by mark 0
• -XX and -X mean standardized parts, so Suivre scrupuleusement les instructions
or dotted line with mark 0 are critical for
they may have some difference from the chaque fois qu’un composant est remplacé
safety.
original one. et / ou réparé.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce por-
tant le numéro spécifié.
7-1. PANEL, SIDE SECTION
top panel section
#1
#1
A
2CH DAMP, 4CH DAMP
board section
1 #1 B
3
#1
3
3
4
#1
A
2
3
#1
#1
3
3 1
5 3
3
2
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 4-558-956-01 COVER SCREW A 4 4-548-124-11 PANEL, SIDE (L) (SHAKE10/SHAKE30)
2 4-558-957-01 COVER SCREW B
3 4-162-271-01 SCREW, TAPPING 5 4-548-125-01 PANEL, SIDE (R) (HCDSHAKEX10/
4 4-548-124-01 PANEL, SIDE (L) (HCDSHAKEX10/ HCDSHAKEX30/HCDSHAKEX70)
HCDSHAKEX30/HCDSHAKEX70) 5 4-548-125-11 PANEL, SIDE (R) (SHAKE10/SHAKE30)
#1 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
53
7-2. 2CH DAMP, 4CH DAMP BOARD SECTION
(SHAKE10/SHAKE30/ (HCDSHAKEX70)
52
52
ns
ns
#1
ns ns ns F
E F E
#1 #1
C DC
53
D
G 53
G
ns ns
#1
(HCDSHAKEX70)
ns #1 ns
(HCDSHAKEX70)
#1
#1
C F
back panel section
D
51
ns 54
ns
55
0 51 1-855-340-11 DC FAN 54 4-295-431-02 SPRING, LOADING
52 4-435-965-01 SCREW+PTPWH 2.6XL (DIA8.0)
53 A-2167-927-A 2CH DAMP BOARD, COMPLETE (SHAKE10/ 55 X-2590-779-2 PANEL, LOADING ASSY
SHAKE30/HCDSHAKEX10/HCDSHAKEX30) #1 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
53 A-2166-772-A 4CH DAMP BOARD, COMPLETE ns not supplied
(HCDSHAKEX70)
54
7-3. BACK PANEL SECTION
#1 #1
#1 #1
(HCDSHAKEX10/ #1
HCDSHAKEX30)
K #2
101 K #2
#1
#1 #1
ns ns
#1 #1
102 J 102 I
I H H
L ns L
ns
(HCDSHAKEX10/HCDSHAKEX30/
HCDSHAKEX70)
J
I
H
L
MOTHERBOARD BOARD section
0 101 1-855-340-11 DC FAN (HCDSHAKEX70) #1 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
102 A-2167-940-A LED DRIVER BOARD, COMPLETE (SHAKE10/ #2 7-682-547-04 SCREW +B 3X6 (HCDSHAKEX10/
SHAKE30/HCDSHAKEX10/HCDSHAKEX30) HCDSHAKEX30/HCDSHAKEX70)
102 A-2167-941-A LED DRIVER BOARD, COMPLETE
(HCDSHAKEX70) ns not supplied
55
7-4. MOTHERBOARD BOARD SECTION

#1
CD/DVD MECHANISM section

(CDM90-DVBU204//M)
151
ns
#1
#1
ns #1
#1
152
153
front panel section
chassis section
#1
Note 1: When the complete MOTHERBOARD board is replaced, Note 2: If flexible flat cable is replaced, install it after bending it in
refer to “NOTE OF REPLACING MOTHERBOARD the same form as that before replacement.
BOARD OR BLUETOOTH MODULE OR RC-S730 (WW)”
on page 7.
151 1-469-829-11 CORE, FERRITE 9 153 A-2184-406-A MOTHERBOARD BOARD, COMPLETE
152 1-912-091-11 FLEXIBLE FLAT CABLE (19 CORE) (for SERVICE) (HCDSHAKEX30: AUS)
(HCDSHAKEX70) 9 153 A-2184-409-A MOTHERBOARD BOARD, COMPLETE
152 1-912-106-11 FLEXIBLE FLAT CABLE (19 CORE) (SHAKE10/ (for SERVICE) (HCDSHAKEX30: EA, E4)
SHAKE30/HCDSHAKEX10/HCDSHAKEX30)
9 153 A-2184-395-A MOTHERBOARD BOARD, COMPLETE 9 153 A-2184-410-A MOTHERBOARD BOARD, COMPLETE
(for SERVICE) (HCDSHAKEX10: AR, LA9) (for SERVICE) (HCDSHAKEX30: AEP, UK)
9 153 A-2184-397-A MOTHERBOARD BOARD, COMPLETE 9 153 A-2184-411-A MOTHERBOARD BOARD, COMPLETE
(for SERVICE) (HCDSHAKEX10: AUS) (for SERVICE) (SHAKE30)
9 153 A-2184-412-A MOTHERBOARD BOARD, COMPLETE
9 153 A-2184-400-A MOTHERBOARD BOARD, COMPLETE (for SERVICE) (HCDSHAKEX70: AR, LA9)
(for SERVICE) (HCDSHAKEX10: EA, E4) 9 153 A-2184-417-A MOTHERBOARD BOARD, COMPLETE
9 153 A-2184-402-A MOTHERBOARD BOARD, COMPLETE (for SERVICE) (HCDSHAKEX70: EA, E4)
(for SERVICE) (SHAKE10) 9 153 A-2184-418-A MOTHERBOARD BOARD, COMPLETE
9 153 A-2184-404-A MOTHERBOARD BOARD, COMPLETE (for SERVICE) (HCDSHAKEX70: AEP)
(for SERVICE) (HCDSHAKEX30: AR, LA9)
#1 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
ns not supplied
56

(SHAKE10/SHAKE30/
204
#1
205
#1
M
203
ns N
IR board (ns) #1
#1
204 (HCDSHAKEX70)
#1
206
205
#1 #1
ns
ns
M
N
#1
ns
#1
#1
ns
202 201
ns
Note 1: When the BLUETOOTH MODULE is replaced, refer to Note 2: If flexible flat cable is replaced, install it after bending it in
“NOTE OF REPLACING MOTHERBOARD BOARD OR the same form as that before replacement.
BLUETOOTH MODULE OR RC-S730 (WW)” on page 7.
201 1-912-099-11 FLEXIBLE FLAT CABLE (10 CORE) 205 A-2183-269-A HI-RGB RIGHT BOARD, COMPLETE
202 1-492-699-32 BLUETOOTH MODULE (HCDSHAKEX70)
203 A-2170-673-A HI-RGB LEFT BOARD, COMPLETE 206 X-2594-413-1 PANEL, FRONT ASSY (SHAUN) (HCDSHAKEX70)
204 A-2183-157-A BAR CENTER BOARD, COMPLETE 206 X-2594-414-1 PANEL, FRONT ASSY (STEVE-LA9)
(HCDSHAKEX70) (HCDSHAKEX10/HCDSHAKEX30)
204 A-2183-158-A SKY BLUE BOARD, COMPLETE (SHAKE10/ 206 X-2594-415-1 PANEL, FRONT ASSY (STEVE-UC2)
SHAKE30/HCDSHAKEX10/HCDSHAKEX30) (SHAKE10/SHAKE30)
205 A-2170-671-A HI-RGB RIGHT LED PC BO BOARD, COMPLETE #1 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
(SHAKE10/SHAKE30/ ns not supplied
57
7-6. CHASSIS SECTION

#1
O
ns
ns
P
251 #1
(HCDSHAKEX70)
251 ns
251
252 252
252 252 252
252
ns
Q Q
ns
254
ns 254
251 ns
ns 251
251 ns
ns
253 253
251 ns O ns 251 ns O
ns
251 251
ns 255 #1 ns 255 #1
Q Q
ns ns ns
#1 P P
ns #1
ns ns
251 3-077-331-21 +BV3 (3-CR) 0 254 1-474-696-11 REGULATOR, SWITCHING (SSN-171AD)
252 2-677-839-01 +PWH 3X8 (SUMITITE) (HCDSHAKEX70)
253 1-457-369-12 CORE, FERRITE
0 254 1-474-694-11 REGULATOR, SWITCHING (SSN-172AD) 0 255 1-844-220-11 AC INLET
(SHAKE10/SHAKE30/ #1 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
HCDSHAKEX10/HCDSHAKEX30) ns not supplied
58
7-7. TOP PANEL SECTION
#1
ns
#1
MIC board (ns)
EN1002
#1 307
#1 306
305
#1 310
#1
TOP PANEL board #1
(ns) #1
(HCDSHAKEX70)
(SHAKE10/SHAKE30/ EN1001
HCDSHAKEX10/
ns
HCDSHAKEX30) 309
ns
ns
302
308
311
ns
304
303 ns
302
ns
301
ns
Note 1: When the RC-S730 (WW) is replaced, refer to “NOTE Note 2: If flexible flat cable is replaced, install it after bending it in
OF REPLACING MOTHERBOARD BOARD OR BLUE- the same form as that before replacement.
TOOTH MODULE OR RC-S730 (WW)” on page 7.
301 X-2590-783-1 KNOB, VOLUME ASSY 311 X-2594-416-2 PANEL, TOP ASSY (SHAUN-LA9)
302 3-087-053-01 +BVTP2.6 (3CR) (HCDSHAKEX70)
303 4-690-207-01 KNOB, MIC 311 X-2594-641-2 PANEL, TOP ASSY (STEVE-LA9) (HCDSHAKEX30)
304 4-214-276-11 TAPE 311 X-2594-675-2 PANEL, TOP ASSY (SAM-LA9) (HCDSHAKEX10)
305 1-912-105-11 FLEXIBLE FLAT CABLE (25 CORE) 311 X-2594-686-2 PANEL, TOP ASSY (STEVE-UC2) (SHAKE30)
311 X-2594-687-2 PANEL, TOP ASSY (SAM-UC2) (SHAKE10)
306 1-912-104-11 FLEXIBLE FLAT CABLE (11 CORE)
307 1-912-098-11 FLEXIBLE FLAT CABLE (7 CORE) EN1001 1-493-008-11 ENCODER, ROTARY (VOLUME/DJ CONTROL)
308 1-912-101-11 FLEXIBLE FLAT CABLE (6 CORE) EN1002 1-493-340-11 ENCODER, ROTARY (MIC/GUITAR LEVEL)
309 8-989-602-00 RC-S730 (WW) #1 7-685-646-71 SCREW +BVTP 3X8 TYPE2 IT-3
310 A-2167-937-A FL BOARD, COMPLETE ns not supplied
59
7-8. CD/DVD MECHANISM SECTION

(CDM90-DVBU204//M)
351 (including MS-476 board)
ns
353
352
353
353
354
ns
ns
ns
MS-476 board
(ns)
356
ns
355
Note: If flexible flat cable is replaced, install it after bending it in

the same form as that before replacement.
351 A-1896-391-B LOADING COMPLETE ASSY (T) 355 1-912-103-11 FLEXIBLE FLAT CABLE (5 CORE)
(including MS-476 board)
352 3-087-599-01 INSULATOR SCREW 356 1-912-102-11 FLEXIBLE FLAT CABLE (24 CORE)
353 2-634-618-21 INSULATOR ns not supplied
0 354 A-2046-956-A SERVICE, OPTICAL DEVICE (7G)
60
SECTION 8
2CH DAMP 4CH DAMP
ELECTRICAL PARTS LIST
BAR CENTER FL
HI-RGB LEFT HI-RGB RIGHT
HI-RGB RIGHT LED PC BO IR
LED DRIVER MIC
Note: • SEMICONDUCTORS The components identified by mark 0

• Due to standardization, replacements in In each case, u: μ, for example: or dotted line with mark 0 are critical for
the parts list may be different from the uA. . : μA. . , uPA. . , μPA. . , safety.
parts specified in the diagrams or the com- uPB. . : μPB. . , uPC. . , μPC. . , Replace only with part number specified.
ponents used on the set. uPD. . : μPD. .
• -XX and -X mean standardized parts, so • CAPACITORS Les composants identifiés par une marque
they may have some difference from the uF: μF 0 sont critiques pour la sécurité.
original one. • COILS Ne les remplacer que par une pièce por-
• RESISTORS uH: μH tant le numéro spécifié.
All resistors are in ohms.
METAL: Metal-film resistor. • Abbreviation The components identified by mark 9 con-
METAL OXIDE: Metal oxide-film resistor. AR : Argentina model tain confidential information.
F: nonflammable AUS : Australian model Strictly follow the instructions whenever the
• Items marked “*” are not stocked since CND : Canadian model components are repaired and/or replaced.
they are seldom required for routine ser- E4 : African model Les composants identifiés par la marque
vice. EA : Saudi Arabia model 9 contiennent des informations confiden-
Some delay should be anticipated when LA9 : Latin-American model tielles.
ordering these items. Suivre scrupuleusement les instructions
chaque fois qu’un composant est remplacé
et / ou réparé.
When indicating parts by reference num-

ber, please include the board name.
A-2167-927-A 2CH DAMP BOARD, COMPLETE (SHAKE10/ A-2170-671-A
HI-RGB RIGHT LED PC BO BOARD, COMPLETE
SHAKE30/HCDSHAKEX10/HCDSHAKEX30) (SHAKE10/SHAKE30/HCDSHAKEX10/
***** HCDSHAKEX30)
*********
< IC > *************************************************************
IC1005 6-722-001-01 IC 78D12AG-TN3-R IR BOARD

IC1006 6-722-002-01 IC 78D07AG-TN3-R ********
IC1007 6-722-003-01 IC 79D07AG-TN3-R
************************************************************* < IC >
A-2166-772-A 4CH DAMP BOARD, COMPLETE IC010 6-600-768-01 IC PNA4823M03S0 ( )

(HCDSHAKEX70) *************************************************************
*************************
A-2167-940-A
LED DRIVER BOARD, COMPLETE (SHAKE10/
< IC > SHAKE30/HCDSHAKEX10/HCDSHAKEX30)
A-2167-941-A LED DRIVER BOARD, COMPLETE
IC1005 6-722-001-01 IC 78D12AG-TN3-R (HCDSHAKEX70)
IC1006 6-722-002-01 IC 78D07AG-TN3-R *************************
IC1007 6-722-003-01 IC 79D07AG-TN3-R *************************************************************
*************************************************************
MIC BOARD
A-2183-157-A
BAR CENTER BOARD, COMPLETE *********
(HCDSHAKEX70)
************************* < DIODE >
*************************************************************
D2218 6-502-961-01 DI DA2J10100L
A-2167-937-A
FL BOARD, COMPLETE D2220 6-502-961-01 DI DA2J10100L
****************** D2222 6-500-400-01 DIODE BAV99-215
************************************************************* D2223 6-500-400-01 DIODE BAV99-215
A-2170-673-A
HI-RGB LEFT BOARD, COMPLETE < FERRITE BEAD >
***************************
************************************************************* FB006 1-469-670-21 FERRITE, EMI (SMD) (2012)
FB007 1-469-670-21 FERRITE, EMI (SMD) (2012)
A-2183-269-A
HI-RGB RIGHT BOARD, COMPLETE
(HCDSHAKEX70) < IC >
*************************
************************************************************* IC2101 6-713-989-01 IC NJM2783V (TE2)
IC2202 8-759-909-71 IC BA4558F
61
MIC MOTHERBOARD MS-476 SKY BLUE TOP PANEL
< JACK > TOP PANEL BOARD
***************
J2203 1-822-967-12 JACK (MIC1)
J2204 1-822-967-12 JACK (MIC2/GUITAR) < CONNECTOR >
< JUMPER RESISTOR > CN1001 1-819-866-11 USB CONNECTOR (A) (REC/PLAY 5V 1A )
CN1002 1-779-544-21 CONNECTOR, FFC (LIF (NON-ZIF)) 7P
JR2200 1-216-296-11 SHORT CHIP 0 CN1004 1-564-722-11 PIN, CONNECTOR (SMALL TYPE) 6P
JR2201 1-216-864-91 SHORT CHIP 0 CN1005 1-779-293-11 CONNECTOR, FFC (LIF (NON-ZIF)) 25P
JR2202 1-216-296-11 SHORT CHIP 0 CN1006 1-779-548-21 CONNECTOR, FFC (LIF (NON-ZIF)) 11P
JR2203 1-216-864-91 SHORT CHIP 0
JR2204 1-216-864-91 SHORT CHIP 0 < DIODE >
JR2205 1-216-296-11 SHORT CHIP 0 D1003 6-500-400-01 DIODE BAV99-215

JR2208 1-216-864-91 SHORT CHIP 0 D1006 6-504-215-01 DI HL-364V620MZ-T
JR2209 1-216-296-11 SHORT CHIP 0 D1007 6-504-213-01 DI HL-364B460MZ-T
JR2210 1-216-864-91 SHORT CHIP 0 D1008 6-502-970-01 DI DZ2J068M0L

D1009 6-504-214-01 DI HL-364W650MZ-T
< TRANSISTOR > D1010 6-504-214-01 DI HL-364W650MZ-T
D1011 6-504-214-01 DI HL-364W650MZ-T
Q2203 6-552-967-01 TR RHK005N03T146 D1012 6-504-214-01 DI HL-364W650MZ-T
Q2205 6-552-936-01 TR LTC014EUBFS8TL
************************************************************* D1013 6-503-719-01 DI 1L0352W32B0MIT01
D1014 6-504-214-01 DI HL-364W650MZ-T
9 A-2184-395-A MOTHERBOARD BOARD, COMPLETE D1015 6-504-214-01 DI HL-364W650MZ-T
(for SERVICE) (HCDSHAKEX10: AR, LA9)
9 A-2184-397-A MOTHERBOARD BOARD, COMPLETE < ROTARY ENCODER >
(for SERVICE) (HCDSHAKEX10: AUS)
9 A-2184-400-A MOTHERBOARD BOARD, COMPLETE EN1001 1-493-008-11 ENCODER, ROTARY (VOLUME/DJ CONTROL)
(for SERVICE) (HCDSHAKEX10: EA, E4) EN1002 1-493-340-11 ENCODER, ROTARY (MIC/GUITAR LEVEL)
9 A-2184-402-A MOTHERBOARD BOARD, COMPLETE
(for SERVICE) (SHAKE10) < IC >
(for SERVICE) (HCDSHAKEX30: AR, LA9) IC1001 6-719-142-01 IC TC62D723FNG
IC1002 6-719-142-01 IC TC62D723FNG
(for SERVICE) (HCDSHAKEX30: AUS) < JUMPER RESISTOR >
(for SERVICE) (HCDSHAKEX30: EA, E4) JR1500 1-216-296-11 SHORT CHIP 0
9 A-2184-410-A MOTHERBOARD BOARD, COMPLETE JR1501 1-216-296-11 SHORT CHIP 0
(for SERVICE) (HCDSHAKEX30: AEP, UK) JR1502 1-216-296-11 SHORT CHIP 0
(for SERVICE) (SHAKE30) JR1504 1-216-296-11 SHORT CHIP 0
(for SERVICE) (HCDSHAKEX70: AR, LA9) JR1505 1-216-296-11 SHORT CHIP 0
JR1506 1-216-296-11 SHORT CHIP 0
9 A-2184-417-A
MOTHERBOARD BOARD, COMPLETE JR1507 1-216-296-11 SHORT CHIP 0
(for SERVICE) (HCDSHAKEX70: EA, E4) JR1508 1-216-296-11 SHORT CHIP 0
(for SERVICE) (HCDSHAKEX70: AEP)
********** JR1510 1-216-296-11 SHORT CHIP 0
************************************************************* JR1511 1-216-296-11 SHORT CHIP 0
JR1512 1-216-296-11 SHORT CHIP 0
MS-476 BOARD JR1513 1-216-296-11 SHORT CHIP 0
************ JR1514 1-216-296-11 SHORT CHIP 0
When the MS-476 board is defective, exchange the entire LOADING JR1515 1-216-296-11 SHORT CHIP 0
COMPLETE ASSY (T). JR1516 1-216-296-11 SHORT CHIP 0
************************************************************* JR1517 1-216-296-11 SHORT CHIP 0
JR1518 1-216-296-11 SHORT CHIP 0
A-2183-158-A
SKY BLUE BOARD, COMPLETE (SHAKE10/ JR1519 1-216-296-11 SHORT CHIP 0
SHAKE30/HCDSHAKEX10/HCDSHAKEX30)
***** JR1520 1-216-296-11 SHORT CHIP 0
************************************************************* JR1521 1-216-296-11 SHORT CHIP 0
JR1522 1-216-296-11 SHORT CHIP 0
JR1523 1-216-296-11 SHORT CHIP 0
JR1524 1-216-296-11 SHORT CHIP 0
JR1525 1-216-296-11 SHORT CHIP 0

Note: When the complete MOTHERBOARD board is replaced,
refer to “NOTE OF REPLACING MOTHERBOARD BOARD
OR BLUETOOTH MODULE OR RC-S730 (WW)” on page 7.
62
TOP PANEL
JR1526 1-216-296-11 SHORT CHIP 0 JR1611 1-216-296-11 SHORT CHIP 0











63
TOP PANEL
JR1672 1-216-296-11 SHORT CHIP 0 MISCELLANEOUS
JR1673 1-216-296-11 SHORT CHIP 0 **************
JR1674 1-216-296-11 SHORT CHIP 0
JR1675 1-216-296-11 SHORT CHIP 0 0 51 1-855-340-11 DC FAN
0 101 1-855-340-11 DC FAN (HCDSHAKEX70)
JR1676 1-216-296-11 SHORT CHIP 0 151 1-469-829-11 CORE, FERRITE
JR1677 1-216-296-11 SHORT CHIP 0 152 1-912-091-11 FLEXIBLE FLAT CABLE (19 CORE)
JR1678 1-216-296-11 SHORT CHIP 0 (HCDSHAKEX70)
JR1679 1-216-296-11 SHORT CHIP 0 152 1-912-106-11 FLEXIBLE FLAT CABLE (19 CORE) (SHAKE10/
JR1680 1-216-296-11 SHORT CHIP 0 SHAKE30/HCDSHAKEX10/HCDSHAKEX30)
JR1683 1-216-296-11 SHORT CHIP 0 202 1-492-699-32 BLUETOOTH MODULE
JR1684 1-216-296-11 SHORT CHIP 0 253 1-457-369-12 CORE, FERRITE
JR1685 1-216-296-11 SHORT CHIP 0 0 254 1-474-694-11 REGULATOR, SWITCHING (SSN-172AD)
JR1686 1-216-296-11 SHORT CHIP 0 (SHAKE10/SHAKE30/HCDSHAKEX10/
HCDSHAKEX30)
JR1687 1-216-296-11 SHORT CHIP 0 0 254 1-474-696-11 REGULATOR, SWITCHING (SSN-171AD)
JR1688 1-216-296-11 SHORT CHIP 0 (HCDSHAKEX70)
JR1689 1-216-296-11 SHORT CHIP 0
JR1690 1-216-296-11 SHORT CHIP 0 0 255 1-844-220-11 AC INLET
306 1-912-104-11 FLEXIBLE FLAT CABLE (11 CORE)
JR1694 1-216-296-11 SHORT CHIP 0
JR1695 1-216-296-11 SHORT CHIP 0 309 8-989-602-00 RC-S730 (WW)
JR1696 1-216-296-11 SHORT CHIP 0 351 A-1896-391-B LOADING COMPLETE ASSY (T)
(including MS-476 board)
JR1697 1-216-296-11 SHORT CHIP 0 0 354 A-2046-956-A SERVICE, OPTICAL DEVICE (7G)
< SWITCH >
S1001 1-762-875-21 SWITCH, TACTILE (DJ EFFECT GUITAR)

S1002 1-762-875-21 SWITCH, TACTILE (VOCAL FADER)
S1003 1-762-875-21 SWITCH, TACTILE ( +)
S1004 1-762-875-21 SWITCH, TACTILE ( ―)
S1005 1-762-875-21 SWITCH, TACTILE (Z)
S1006 1-762-875-21 SWITCH, TACTILE ( TUNING + >)

S1007 1-762-875-21 SWITCH, TACTILE ( TUNING ― .)
S1008 1-762-875-21 SWITCH, TACTILE (ENTER)
S1009 1-762-875-21 SWITCH, TACTILE (FIESTA)
S1014 1-762-875-21 SWITCH, TACTILE (1)
S1015 1-762-875-21 SWITCH, TACTILE (MIC ECHO)

S1016 1-762-875-21 SWITCH, TACTILE (REC TO USB)
S1017 1-762-875-21 SWITCH, TACTILE (MEGA BASS)
S1018 1-762-875-21 SWITCH, TACTILE ( PAIRING BLUETOOTH)
S1019 1-762-875-21 SWITCH, TACTILE (LIGHT MODE)
S1020 1-762-875-21 SWITCH, TACTILE (PARTY LIGHT)

S1021 1-762-875-21 SWITCH, TACTILE (x)
S1022 1-762-875-21 SWITCH, TACTILE (N)
S1025 1-762-875-21 SWITCH, TACTILE (PARTY CHAIN)
S1026 1-762-875-21 SWITCH, TACTILE (DJ EFFECT FUNCTION)
S1027 1-762-875-21 SWITCH, TACTILE (FOOTBALL)

S1028 1-762-875-21 SWITCH, TACTILE (DJ EFFECT ISOLATOR)
S1029 1-762-875-21 SWITCH, TACTILE (SOUND FIELD)
S1030 1-762-875-21 SWITCH, TACTILE (DJ EFFECT SAMPLER )
S1031 1-762-875-21 SWITCH, TACTILE (DJ EFFECT FLANGER)
S1032 1-762-875-21 SWITCH, TACTILE (DJ EFFECT DJ OFF)

*************************************************************
Note 1: If flexible flat cable is replaced, install it after bending it in

the same form as that before replacement.
Note 2: When the BLUETOOTH MODULE and RC-S730 (WW)

are replaced, refer to “NOTE OF REPLACING
MOTHERBOARD BOARD OR BLUETOOTH MODULE
OR RC-S730 (WW)” on page 7.
64
MEMO
65
REVISION HISTORY
Ver. Date Description of Revision

1.0 2017.03 New
How to search for a contact point of signal lines or the like in DIAGRAMS SECTION
If a contact point of a BLOCK DIAGRAM, PRINTED WIRING BOARD or SCHEMATIC DIAGRAM is shown in a different page, use
the PDF file search function to find one.
e.g.) If a contact point is shown as , follow the procedure below.

Procedure:
1. Press the [F] key while pressing the [Ctrl] key.
2. Input “>001Z” in the search box and press the [Enter] key.
3. The relevant part (page), where the contact point is shown, appears.
Note: If you still see the original page, press the [Enter] key again.

Sony Hcd-Shake10 30 Hcdshakex10!30!70 Ver.1.0 SM

Uploaded by

Copyright:

Available Formats

Sony Hcd-Shake10 30 Hcdshakex10!30!70 Ver.1.0 SM

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sony Hcd-Shake10 30 Hcdshakex10!30!70 Ver.1.0 SM

Uploaded by

Copyright:

Available Formats

HCD-SHAKE10/SHAKE30/

Photo: HCDSHAKEX70 Australian Model

Model Name Using Similar Mechanism HCD-SHAKEX1/SHAKEX3/SHAKEX7

Supported audio formats License and Trademark Notice

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE • Abbreviation

LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR

NOTES ON CHIP COMPONENT REPLACEMENT

FLEXIBLE CIRCUIT BOARD REPAIRING

5. TROUBLESHOOTING .......................................... 24 8. ELECTRICAL PARTS LIST .............................. 61

: LEAD FREE MARK L

Unleaded solder has the following characteristics.

• Usable with ordinary solder PART No. Destination Code

PLAYABLE DISCS TEST DISCS

NOTE OF REPLACEMENT OF THE MS-476 BOARD

RELEASING THE DISC TRAY LOCK

NOTE OF REPLACING MOTHERBOARD BOARD OR

Complete the connection by following the instructions

HOW TO OPEN THE TRAY WHEN POWER SWITCH TURN OFF

1 Remove the side (L,R) panel, top panel section,

Note: Push after it inserts it in this hole well.

CAPACITOR DISCHARGE FOR ELECTRIC SHOCK PREVENTION

Switching Regulator (SSN-172AD) Board (Conductor side view) (HCD-SHAKE10/SHAKE30/HCDSHAKEX10/HCDSHAKEX30)

CAPACITOR DISCHARGE FOR ELECTRIC SHOCK PREVENTION

Switching Regulator (SSN-171AD) Board (Conductor side view) (HCDSHAKEX70)

800 :/5 W 800 :/5 W 800 :/5 W

C18 800 :/5 W

panel, top assy

TOP PANEL board

MOTHERBOARD board 2CH DAMP board

2-1. DISASSEMBLY FLOW

2-2. PANEL, SIDE (L), PANEL, SIDE (R),

2-3. 2CH DAMP BOARD 2-4. 4CH DAMP BOARD

2-5. BACK PANEL SECTION 2-6. BACK PANEL SECTION

2-7. PANEL, LOADING ASSY

2-9. FRONT PANEL SECTION

2-10. MOTHERBOARD BOARD

2-11. REGULATOR, SWITCHING (SSN-172AD) 2-12. REGULATOR, SWITCHING (SSN-171AD)

2-13. SERVICE, OPTICAL DEVICE (7G),

Note: Follow the disassembly procedure in the numerical order given.

wk top panel section

1 Insert the qh one screw qf panel, side (R) qs two screws

qa one tapping screw

0 cover screw B 8 Insert the clip etc.

filament tape RC-S730 (WW) MIC board

colored line colored line

2-3. 2CH DAMP BOARD (SHAKE10/SHAKE30/HCDSHAKEX10/HCDSHAKEX30)

qa heat sink (M3)

2 two screws 3 two screws

6 flexible flat cable

colored line colored line

2-4. 4CH DAMP BOARD (HCDSHAKEX70)

qd heat sink (M3)

5 two screws qg stopper, wiring

8 flexible flat cable 1 CN1011 (2P)

colored line colored line

2-5. BACK PANEL SECTION (SHAKE10/SHAKE30/HCDSHAKEX10/HCDSHAKEX30)

1 one screw (HCDSHAKEX10/

(HCDSHAKEX10/ 4 five screws

2-6. BACK PANEL SECTION (HCDSHAKEX70)

,QVWDOODWLRQRIIOH[LEOHIODWFDEOH FRUH DQGIOH[LEOHIODWFDEOH FRUH