0% found this document useful (0 votes)
62 views2 pages

ENG ISP-Programmer Stick

The document provides instructions for installing a USB-ISP programmer driver. It describes downloading the correct driver file for the user's operating system from the seller's website. It then gives steps to store the file, connect the programmer, and select the file during driver installation. The document also provides specifications for the programmer and a list of supported microcontrollers.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
62 views2 pages

ENG ISP-Programmer Stick

The document provides instructions for installing a USB-ISP programmer driver. It describes downloading the correct driver file for the user's operating system from the seller's website. It then gives steps to store the file, connect the programmer, and select the file during driver installation. The document also provides specifications for the programmer and a list of supported microcontrollers.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

USB-ISP programmer

Installation:
Please download the *inf file for the ISP-programmer driver.
Please download the last driver “AVR-ISP-Driver” for the ISP-Programmer on the seller’s website
www.diamex.de. Go to the download section where you can also download a product description.
“Stange ISP Prog” for Win XP
“Dx_ISP.inf” Vista or Win2000
“avr-isp.inf” for Win7
For Windows 8 please read the information at the end of the description.

Store the *inf file on the hard drive or in a search path. Connect the programmer and run (automatic)
the driver assistant.
During the installation Windows will ask for a driver. The windows driver will be used which will be
communicated to the system by the special Stange_ISP_Prog.inf file.

In the next dialogue specify where the .inf file is located.

ISP-SPI-speed:
Due to the USB connection minor deviating ISP-frequencies may be caused towards a STK500.

STK500 ISP-Prog
921.6kHz 1MHz
230.4kHz 250kHz
57.6kHz 62.5kHz
28.8kHz 28.2kHz
4kHz 4kHz
603Hz 779Hz

LEDs
-USB-LED: flashes during USB activity
-Target LED: shut off in idle, flashes during target access
Functions
-FLASH, EEPROM, Fusebits, writing Lockbits, reading, chip erase, reading OSCCAL register
Log
-STK500v2
Software assisted
-AVR Studio (COM1…COM9) Version 4/5/6
-AVRDUDE
-Bascom with setup-options-programmer=STK500:
C:/Programms/Atmel/AVR Tools/STK500/stk500.exe (STK500 native driver) and installed AVR Studio
4/5/6

Switch position for normal programming in user’s switching= both switch OFF
If voltage supply of the target is needed.
For a single AVR controller only without own switching 5V are required (for example Diamex program
adapter/pivot lever) 1=on 2=on
General: 3.3V max. 120mA, 5V 150-500mA. Depending on which computer is used.
Switch 1 off= target voltage off/on, switch 2 off= 3.3V / on=5.0V. The programmer doesn’t need a
power supply from the target for the programming operation.

Equipment
-ISP programmer in a stick case
-USB 2.0
-SPI connection cable 6 pin 15cm (Atmel standard – check the upper drawing) 15cm
-manual

Supports the following controller:


Classic
AT90S1200, AT90S2313, AT90S2333, AT90S2343, AT90S4414, AT90S4433, AT90S4434, AT90S8515,
AT90S8535

Tiny
ATtiny12, ATtiny13, ATtiny15, ATtiny2313, ATtiny24, ATtiny25, ATtiny26, ATtiny44, ATtiny45,
ATtiny85, ATtiny86, ATtiny261, ATtiny461, ATtiny861

Mega
ATmega88, ATmega103, ATmega128, ATmega1280, ATmega1281, ATmega16, ATmega161,
ATmega162, ATmega163, ATmega164, ATmega168, ATmega169, ATmega2560, ATmega2561,
ATmega32, ATmega324, ATmega325, ATmega3250, ATmega329x, ATmega64, ATmega640,
ATmega644, ATmega645, ATmega6450, ATmega649x, ATmega8, ATmega8515. ATmega8535

Further
AT90CAN128, AT90PWM2, AT90PWM3, AT90PWM3B, AT90USB162, AT90USB646, AT90USB647,
AT90USB1286, AT90USB1287
and all ATMEGA processors, which support the ISP-programmer interface. Also Arduino boards are
supported.

Driver installation for Windows 8:


Driver installation for Windows 8:
The Windows 7 driver works also on Windows 8. The following report appears:
The Windows 7 driver works also on Windows 8. The following report appears:
“The third party *inf file does not contain digital signature information”
“The third party *inf file does not contain digital signature information”
Charme set up on/off - hold shift and click on restart or
Charme set up on/off - hold shift and click on restart or
Charme set up / More PC settings / General / Advanced start up then troubleshot /advanced options
Charme set up / More PC settings / General / Advanced start up then troubleshot /advanced options
start set up. The computer will restart and shows a menu please press key 7.
start set up. The computer will restart and shows a menu please press key 7.
Disable driver signature – Now the driver can be installed.
Disable driver signature – Now the driver can be installed.
For any questions please do not hesitate to contact us: [email protected] / [email protected]

You might also like