®

TYPE 2RH
Hollow through Shaft CHARACTERISTICS
ENCODER TYPE Hollow through shaft encoder

SMD - TECHNOLOGY Strong compact electronics

HIGH IP-RATING Std. IP 65

LOW CURRENT CONSUMPTION To be connected directly to

PLC'S and counters

SHORT CIRCUIT PROTECTION Thermal shut down at 155°C

WIDE SUPPLY RANGE Min. 4,5V to max. 30V

STRONG MEC. CONSTRUCTION Based on 2 precision ball

bearings, for harsh industrial
environments

ELECTRICAL SPECIFICATIONS MECHANICAL SPECIFICATIONS

At +25°C
Output waveform Incremental (A, B, Z and inverted) Weight About 150 g
Zero or index pulse (Z) one pr./rev. Materials : Housing Aluminum
Output Totempole (TP) Shaft Brass
Supply-voltage (Vin) Min. 4,5V to Max. 30V * Bearings Lifetime lubricated ball bearings
Reverse polarity protection H.-Shaft dimensions ø6 mm
Current (no load) Max. 45 mA ø8 mm
Max. load pr. output 30 mA - (Shortcircuit protected) * H.-Shaft loads Axial max. 20 N
V out low Max. 500 mV @ I =10 mA Radial max. 20 N
Operating temp. - 40°C to + 85°C Max. rev. 12.000 rev./min.
Storage temp. - 40°C to + 85°C IP-rating Standard IP 65 at 25°C
Max. pulse frequency 300 kHz * Start torque < 0,01 Nm at 25°C
V out high Min. (Vin -0,6) @ I = -10mA Mass moment 4 gcm²
Min. (Vin -1,3) @ I = -25mA of inertia
Cable data 8-leads (0,14 mm²)pairtwisted/shielded Max. shock 100 G/11 ms
Output signals Normal (Standard), Bump 10 G - 16 ms (1000 x 3 axis)
Inverted, Vibration (10 - 2000 Hz)/10 G
Differential (RS-422A compatible @ 5V)
Certified acc. to EN 50081-1 and EN 50082-2

* = It is not recommended to combine

max. value for all 3 parameters

OUTPUT CIRCUIT MECHANICAL DIMENSIONS

3 x M3 Unbraco screw for fasten shaft; back mounting
36
L = 34 ø58 3 x ø3,5
29 ø64
1,5 4,5
+ Vcc
2
Hollow through shaft: View shaft option

Note L
Ø50
Ø15

Signal

Protection Cap IP65

16

(removable to make Ø38

10 Hollow through shaft IP50)
0 - Volt Torsionally stiff spring coupling 3 pcs. M2,5
Option: 3-Point coupling max length = 4mm
or Y-coupling
* Shield connected to housing Shield* Max. movement axial ±0,25
Max. movement radial ±0,05 (Tolerance mm - + 0,2)

Section 14 - page 1
 OUTPUT WAVEFORM CONNECTIONS
Rotation: Clockwise (cw) from shaftside
Color code Standard
(inv = inverted channels) y
Pink Ch. A
360°e x Grey* Ch. A Gnd
Green Ch. B
channel A Yellow* Ch. B Gnd
channel A-inv White Ch. Z
Brown* Ch. Z Gnd
channel B Red Vcc
Blue* Gnd
channel B-inv
*Blue, grey, yellow and brown are internal connected
channel Z
(gated)
channel Z-inv
(gated)
Color code Differential
X = 180°e ± 36°e and Y = 90°e ± 18°e
Z puls: Gated with A and B (standard) Pink Ch. A
Grey Ch. A inv.
Options: TTL or HTL compatible. Open Collector NPN or PNP Green Ch. B
Gated Z-puls or none-gated Z-puls. Yellow Ch. B inv.
View more Output options in section 15 - page 1 White Ch. Z
Brown Ch. Z inv.
Red Vcc
Blue Gnd
ORDERING CODES
Options Ordering codes
Pulses pr. rev.: No. of pulses XXXXX

Output signal: Normal, TP-Standard, A, B, Z

(3 channel) N
PULSES/REV.
TP-Differential: A, B, Z and
A-inv, B-inv, Z-inv 1 32 150 600 2048
(6 channel) D
2 36 180 635 2500
Line driver OL 7272 for 5 40 200 720 3000
extra long cable, up to 6 50 250 800 3600
100 meters (Differential) M 8 60 300 1000 4000
10 64 360 1024 4096
Line driver chip 26C31
(V out low < 0,4 V) 15 75 400 1131 5000
(RS-422A compatible @ 5V) 16 80 455 1250 9000
Only 5 Volt (Differential) L 20 90 500 1500 12500
25 100 512 2000
Shaft dimensions ø6 mm (tolerance G7) 06
(Through) ø8 mm (tolerance G7) 08 30 125

IP-rating: IP 65 65

Length of cable: Standard 1 meter 01

No. of meters XX Advanced Output Options:
Cable take out: Side (Radial) S Options Ordering codes
(or connector)
Normal Open Collector NPN NON
Anti rotation
View Section 15 page 1 to 8 Differential Open Collector NPN DON
Spring coupling:

Normal Open Collector PNP NOP

Connector: Coninvers Connector Differential Open collector PNP DOP
View Section 20 page 6
To order, replace with O
Output Output
signal signal

2RH 65 S
Pulses Output H.-Shaft IP-rating Length Cable Anti Rotation Accessories Order Number
signal of cable take out Spring Coupling

TLF. +45 48 17 27 02 · FAX +45 48 17 22 84 Eng. Rev 001

Feb - 2007
[email protected] www.scancon.dk Section 14 - page 2