Scribd
Upload
173 views2 pages

SPD-48500B Installation and Wiring

This document provides installation and wiring instructions for the SPD-48500B speed controller. It lists the controller's specifications, including a rated voltage of 48 volts, maximum current of 20 amps, and 95% efficiency. It describes the undervoltage protection that turns off the motor below 42 volts to protect the battery. Connection diagrams show how to wire the power, motor, throttle, key switch, battery charger, brake switch, and indicator light connectors. Fusing between the controller and battery is required for protection.

Uploaded by

M
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
173 views2 pages

SPD-48500B Installation and Wiring

This document provides installation and wiring instructions for the SPD-48500B speed controller. It lists the controller's specifications, including a rated voltage of 48 volts, maximum current of 20 amps, and 95% efficiency. It describes the undervoltage protection that turns off the motor below 42 volts to protect the battery. Connection diagrams show how to wire the power, motor, throttle, key switch, battery charger, brake switch, and indicator light connectors. Fusing between the controller and battery is required for protection.

Uploaded by

M
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

4/5/2021 SPD-48500B Installation and Wiring

Speed Controller SPD-48500B Installation and Wiring


Rated Voltage 48 Volts
Rated For Motors Up To 500 Watts
Maximum Current 20 Amps
Rated For Chargers Up To 3 Amps
Conversion Efficiency 95%
Under Voltage Protection 42 Volts
Recommended Fuse Size 25 Amps
Dimensions (including mounting tabs) 4" Long x 2-5/8" Wide x 1-1/2" High
Under Voltage Battery Protection: When the battery pack falls below a specific Voltage the controller
turns the motor off preventing over discharging of the battery pack which extends the battery packs
lifespan. (The cutoff value is approximately 42 Volts ± 0.5 Volts)
Motor Cut-Off During Braking: When the brakes are engaged the brake switch signals the controller
to turn off the motor.

*Power Connector
Red = Positive
Black = Negative
Mating Connector
Item # CNX-50
Required Connection

Motor Connector
Blue = Positive
Yellow = Negative
Mating Connector
Item # CNX-50
Required Connection

Throttle Connector
Red = + 5 Volts Output
Black = Negative
Blue = 1-4 Volts Input
Mating Connector
Item # CNX-52
Required Connection

Key or Power Switch Connector


Blue & Red Disconnected = Power Off
Blue & Red Connected = Power On
Mating Connector
Item # CNX-51 Required Connection

Battery Charger Connector


Red = Positive
Black = Negative
Mating Connector
Item # CNX-51 ~Optional Connection
Brake Lever Switch Connector
Black & Yellow Connected = Motor Off
Black & Yellow Connected = Brake Light On
Mating Connector
Item # CNX-51 ~Optional Connection
Brake Light Connector
Goes To 36 Volt Brake Light
Red = Positive
Black = Negative

~Optional Connection
https://electricscooterparts.com/hookup/SPD-48500Bwiring.htm 1/2
4/5/2021 SPD-48500B Installation and Wiring
Mating Connector
Item # CNX-51
Power Light Connector
Goes To 36 Volt Power On Indicator Light
Red = Positive
Black = Negative
Mating Connector
Item # CNX-51 ~Optional Connection
*The power connector should be the last connection made.
*Fuse or circuit breaker protection is required between speed controller and battery pack.
~Optional Connections do not need to be hooked up for the speed controller to operate.

https://electricscooterparts.com/hookup/SPD-48500Bwiring.htm 2/2

You might also like