CCNA Course

Name of the Course:
CCNA v7 (200-301)
Mode of Training: Online (Zoom)
Course Fee in Total - 150 USD

Discounted Course Fee – 120 USD
Duration of the course: 25 Classes & 50 Hours
Time: 7 PM (GMT+6)
Day: Weekend / Weekdays
Mode of Payment: MoneyGram / RIA / Bank

One Time Payment
Payment should be done before the Class is started
Admission Form:
https://docs.google.com/forms/d/e/1FAIpQLSe0tm3eFOHiLRYn1QkKjCbtONYqhqo4A2ffJZM
gFh0eehmnfg/viewform?usp=pp_url
Instructor Details:
Ashish Halder
4XCCNP, CCIE DC
Cisco Global Trainer
Cell: +88-01830618474
Regards,
Ashish Halder
CEO & Network Solution Architect
E5 Networks
Website: www.e5nets.com
COURSE OUTLINE
• Cisco Command-Line Interface (CLI)

• Taking console of Router
• IOS Modes on devices
• Use of various show Commands
• Use of copy, write, erase and delete command
• Configuring various Passwords on devices
• Configuring an IPv4 address on a Router
• Configuring Telnet
• Configuring SSH
• Configuring DHCP
• Configuring DNS
• Configuring HTTP services on a Router
• Backup and Restoration of Configuration
• Performing Password Recovery on a router
• Backup of IOS on a router
• Restoration of IOS on a router
• Configuring Static Routing on two routers
• Configuring Static Host Route on Router
• Configuring Static Routing on three routers
• Changing AD Value of a Static Route
• Configuring Static Default Route on Router
• Configuring Static Discard Route on Router
• Configuring Single Area OSPF
• Verification of OSPF routing table
• Verification of neighbor table
• Verification of database table
• Verifying an OSPF process on interfaces in detail
• Changing Hello and Dead Interval on interfaces
• Changing Interface Cost
• Use of ip ospf mtu-ignore command on interface
• Changing OSPF network type
• Changing OSPF Priority on interface
• Shutting down the OSPF process on interface
• Debugging the OSPF adjacency
• Changing reference-bandwidth for cost calculation
• Flooding default route information using default-information
• Defining an administrative distance value using distance command
• Controlling the forwarding of packets over multiple paths using maximum-paths
• Using passive-interface command to suppress update information
• Changing router-id for OSPF process using router-id command
• Shutting down the OSPF process by shutdown command.
• Configuring Multi Area OSPF on router using network command
• Using show ip ospf border-routers command to verify ABRs and ASBRs
• Configuring IPv6 Static Routing on two routers using Next Hop IP Address
• Configuring IPv6 Static Host Route on Router
• Configuring IPv6 Static Routing on three routers
• Changing AD Value of an IPv6 Static Route – Path Preference; Static Floating Route
• Configuring IPv6 Static Default Route on Router
• Verifying the newly installed Static routes by show ipv6 route command
• Ping and traceroute to check the reachability
• Mac Address-table verification
• Adding and clearing an entry from Mac Address-table
• Changing the aging time of mac address table
• Assign IP address on VLAN interface to take backup and recover the configuration and
IOS.
• Creating and renaming Access and Voice VLANs on a switch
• Assigning VLAN membership to switchports
• Verifying VLAN information by show vlan brief command
• Configuring access and trunk ports on switches
• Defining trunk encapsulation protocol; Dot1q, ISL or negotiate
• Verifying trunk ports by show interfaces trunk command
• Changing Native VLAN and removing a VLAN from allowed VLAN list on trunk ports
• Using DTP for trunking by using switchport mode dynamic auto/desirable command
• Turning off trunk negotiation by switchport no-negotiate command
• Configuring Inter-VLAN Routing using Router
• Configuring Inter-VLAN Routing using Layer 3 Switch
• Verifying Spanning Tree Protocol operation for loop avoidance
• Changing Spanning-Tree mode using spanning-tree mode command
• Manipulating Root Bridge election process
• Manipulating Root Port / Designated port election
• Configuring spanning-tree portfast feature for rapid convergence
• Configuring and verifying Port-Security on switchports
• Performing err-disable recovery of switchports
• Configuring BPDU Guard feature on switches
• Creating and defining permit/deny statements in a standard ACL
• Applying Standard Access Control List on router interface
• Verifying the reachability after applying standard ACL
• Editing existing ACL using ip access-list standard command
• Allowing specific IPs to remotely access the router by using ACL
• Creating and defining permit/deny statements in an extended ACL on router
• Applying extended Access Control List on router interface
• Verifying the reachability after applying extended ACL
• Editing existing ACL using ip access-list extended command
• Blocking services like HTTP, HTTPs, FTP, DNS, DHCP etc with extended ACL
• Configuring and applying named ACL on router
• Configuring IPv6 access-list and applying on proper interface.
• Defining Inside and Outside interface for NAT
• Configuring Static NAT on a router
• Configuring Dynamic NAT for a range of private IP addresses
• Configuring Port Address Translation
• Verifying NAT
• Debugging the NAT translations
• Clearing older translations
• Configuring HSRP
• Enabling HSRP Preempt
• Changing HSRP priority on interface
• Tracking and Interface using standby <group no> track command
• Configuring and verifying ICMP echo-based IP SLA.
• Creating a track object for tracking the SLA, interface and route
• Using the track object in HSRP to track the reachability to the IP
• Changing HSRP group name by standby <group no> <name> command
• Configuring CDP and LLDP on Switches
• Verifying CDP and LLDP Status
• Configuring and Verifying NTP server on router
• Enabling SNMP on router
• Using logging host command on a router for capturing log messages on Syslog server
• Log into the WLC
• Monitor the WLC
• Configure a Dynamic (VLAN) Interface
• Configure a DHCP Scope
• Configure a WLAN
• Define a Remote Access Dial-In User Service (RADIUS) Server
• Explore Management Options
• Configure and Verify NTP
• Configure System Message Logging
• Create the Cisco IOS Image Backup
• Upgrade the Cisco IOS Image
• Secure Console and Remote Access
• Enable and Limit Remote Access Connectivity
• Secure Device Administrative Access
• Configure and Verify Port Security

CCNA Course

Uploaded by

Copyright:

Available Formats

CCNA Course

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

CCNA Course

Uploaded by

Copyright:

Available Formats

Name of the Course:

Mode of Training: Online (Zoom)

Course Fee in Total - 150 USD

Mode of Payment: MoneyGram / RIA / Bank

• Cisco Command-Line Interface (CLI)

You might also like