GENERAL CONSTRUCTION NOTES

REINFORCING CONCRETE LINTEL BEAMS IN NOTES ON WELDS

CONCRETE BLOCK WALLS 1. USE E60xx ELECTRODES FOR ALL MEMBERS WELDED.
2. WELDS SHALL DEVELOP THE FULL STRENGTH OF MEMBERS JOINED UNLESS
OTHERWISE SHOWN OR DETAILED IN THE DRAWINGS.
TABLE 'A' TABLE 'B' LINTELS IN BLOCK WALLS
TENSION BARS COMPRESSION BARS
CLEAR TOTAL MIN. HEIGHT OF REINFORCEMENT NOTES ON STRUCTURAL STEEL
TABLE OF LAP SPLICE & ANCHORAGE LENGTH (mm) TABLE OF LAP SPLICE & ANCHORAGE LENGTH (mm)
SPAN LENGTH fc' LINTEL 1. STRUCTURAL STEEL TO BE USED FOR FABRICATION AND ERECTION OF THIS
(L) (L+0.40M) (MPa) (mm) BOTTOM TOP STIRRUPS
BAR SIZES fc`= 20.7MPa(300psi) fc`= 27.6 MPa (4000psi) BAR SIZES fc`= 20.7MPa(300psi) fc`= 27.6 MPa (4000psi) STRUCTURE SHALL COMPLY WITH ALL THE PERTINENT PROVISION OF AISC
(DEFORMED MM) (DEFORMED MM)
EMBEDMENT LAPPED EMBEDMENT LAPPED EMBEDMENT LAPPED EMBEDMENT LAPPED 1-Ø 10‘ 1-Ø SPECIFICATION FOR THE DESIGN, FABRICATION AND ERECTION OF STRUCTURAL
1.20 M 1.60 M 200 ‘10‘ Ø6 mm @ 200mm
1-Ø STEEL FOR BUILDING LATEST EDITION.
‘ 300 300 300 300 ‘ 225 300 200 300 1.50 M 1.90 M 14.0 200 ‘10 1-Ø
‘10 Ø6 mm @ 200mm
1.80 M 2.20 M 200 1-Ø
‘12 1-Ø
‘10 Ø6 mm @ 200mm 2. ALL STRUCTURAL STEEL SHAPES SHALL CONFORM TO ASTM A36 STRUCTURAL
‘ 300 300 300 300 ‘ 275 300 250 300
STEEL UNLESS OTHERWISE INDICATED.
‘ 300 400 300 400 ‘ 350 400 325 400
2.10 M 2.50 M 250 1-Ø
‘12 1-Ø
‘10 Ø6 mm @ 200mm
3. ALL WELDED CONNECTIONS SHALL DEVELOP THE FULL STRENGTH OF THE
‘ 400 550 350 500 ‘ 450 500 475 500 2.40 M 2.90 M 17.0 250 1-Ø
‘12 1-Ø
‘10 Ø6 mm @ 200mm
MEMBERS CONNECTED.
2.70 M 3.10 M 250 1-Ø
‘16 1-Ø
‘12 Ø10 mm @ 200mm
‘ 600 800 550 750 ‘ 550 625 550 625 4. UNLESS OTHERWISE SPECIFIED ALL WELDING RODS SHALL CONFORM WITH
‘ 750 1000 650 850 ‘ 625 675 625 675 3.00 M 3.40 M 300 1-Ø
‘16 1-Ø
‘12 Ø10 mm @ 200mm E60 ELECTRODES.
850 700 3.30 M 3.70 M 20.0 300 1-Ø
‘16 1-Ø
‘12 Ø10 mm @ 200mm 5. ALL BOLTS USED UNLESS OTHERWISE SPECIFIED SHALL BE ASTM A 307 BOLTS.
‘ 950 1300 1100 ‘ 700 775 775
3.60 M 4.00 M 300 1-Ø
‘20 1-Ø
‘12 Ø10 mm @ 200mm

NOTES: NOTES: NOTES ON EMBBED PIPES

1. TOP PLAIN BARS, MULTIPLY VALUE BY 2 1. TOP PLAIN BARS, MULTIPLY VALUE BY 2
2. NOT MORE THAN 33% OF THE BARS SHALL BE 2. NOT MORE THAN 33% OF THE BARS SHALL BE 1. ALL EMBEDED PIPES FOR UTILITIES ETC. THAT PASS THRU BEAMS SHALL NOT
SPLICED WITHIN THE REQUIRED LAP LENGTH SPLICED WITHIN THE REQUIRED LAP LENGTH
EXCEED 100mm IN DIAMETER OR 1/3 BEAM DETPH WHICHEVER IS LESS, UNLESS
3. VALUES GIVEN ABOVE CAN ALSO BE USED FOR COLUMNS
OTHERWISE APPROVED IN WRITING BY THE STRUCTURAL ENGINEER.
12 THK. EXPANSION JOINT
WITH MASTIC FILLER
2. NO PIPES SHALL BE ALLOWED TO PASS THRU BEAMS VERTICALLY.
3. NO PIPES SHALL BE EMBEDDED IN COLUMNS.

‘ 1-Ø16 VERT. BARS

NOTES ON CONSTRUCTION JOINTS IN CONCRETE

(DOWEL)
400
CHB WALL
3. IF THE BEAM REINFORCING BARS END IN A WALL, THE CLEAR DISTANCE FROM THE BAR TO THE FARTHER FACE OF THE
‘ 1-Ø16 VERT. BARS 1. WHERE A CONSTRUCTION JOINT IS TO BE MADE, THE SURFACE OF CONCRETE
WALL IS NOT LESS THAN 25mm. EMBEDMENT LENGTH SHALL BE SHOWN IN A TABLE 'A' FOR TENSION BARS AND TABLE 'B' FOR SIZE AND SPACING
OF HOR. & VERT. BARS SHALL BE CLEANED AND ALL LAITANCE AND STANDING WATER REMOVED SHEAR
FOR COMPRESSION BARS UNLESS UNLESS SPECIFIED IN PLAN. TOP BARS AND SHALL NOT BE SPLICED WITHIN THE KEY SHALL BE PROVIDE AT THE JOINT.
FOR SIZE AND SPACING SEE CONSTRUCTION NOTES.
COLUMN OR TWO STIRRUPS SHALL BE PROVED AT ALL SPLICES. OF HOR. & VERT. BARS
SEE CONSTRUCTION NOTES. MAIN REINFORCEMENTS TO BE
4. IF THERE ARE TWO OR MORE LAYERS OF REINFORCING BARS, USED 25mm BAR SEPARATORS SPACED AT 1.0M ON CONTINUOUS (TOP & BOTT. BARS)
ON CENTER ON NO CASE SHALL THERE BE THAN TWO (2) SEPARATORS BETWEEN LAYERS OF BARS CHB WALL
MAIN REINFORCEMENTS WHERE JOINTS IS AT POINT OF
5. MINIMUM CONCRETE PROTECTION FOR REINFORCING BARS OR STEEL SHAPES SHALL BE AS SHOWN IN FIGURE B-2 TO BE CONTINUOUS STRESS, PROVIDE SHEAR RODS
WITH ENGINEERS APPROVAL
UNLESS ELSEWHERE. CORNER WALL OPENING OR END WALL
Ø 10 X 1000 LONG
@ 300 O.C.
300 BAR 300 BAR
50
(MIN.) (MIN.)
40

D/3
MAIN REINFORCEMENT MAIN REINFORCEMENT

D/3
t/3 t/3

D
t/3
t OR 1/4 D

t OR 1/4 D

t
SLEEVES FOR UTILITY

D/3
SLEEVES FOR UTILITY
t

PIPES MAX. 1/5 D PIPES MAX. 1/5 D SLAB BEAM

D

CHB WALL R.C. COLUMN OR WALL

3529,'( ‘ (;75$ 67,55 3529,'( ‘ (;75$ 67,55 TYPICAL SLAB & BEAM
EACH SIDE OF SLEEVES EACH SIDE OF SLEEVES 1-Ø16 VERT. BARS DOWEL BARS TO MATCH
CHB HOR. BARS CONSTRUCTION JOINT DET.
12 THK. EXPANSION JOINT
12 THK. EXPANSION JOINT
TYP. DET. FOR SLEEVES TYP. DET. FOR SLEEVES WITH MASTIC FILLER
WITH MASTIC FILLER

THRU CONCRETE BEAM THRU CONCRETE BEAM NOTES ON STIRUPS

1. ALL REINFORCEMENT SHALL BE BENT COLD UNLESS
FIG. B-2 FIG. B-3

(DOWEL)
OTHERWISE PERMITTED BY THE STRUCTURAL ENGINEER.

400
FOR SIZE AND SPACING 2. AS SHOWN IN THE DESIGN DRAWINGS OR
6. WHEN A BEAM CROSSES A GIRDER , REST BEAM ON TOP OF GIRDER BARS, BEAM REINFORCING BARS SHALL BE OF HOR. & VERT. BARS PERMITTED BY THE STRUCTURAL ENGINEER.
SEE CONSTRUCTION NOTES. 400
SYMMETRICAL ABOUT THE CENTER LINE WHENEVER POSSIBLE. 3. TIES & CLOSE STIRRUPS MUST BE AT 135.
(DOWEL)
7. GENERALLY, NO SPLICES SHALL BE PERMITTED AT POINTS WHERE CRITICAL BENDING STRESSES OCCUR, SPLICES
WHERE SO PERMITTED SHALL BE INDICATED IN TABLE 'A' AND 'B'. WELDED SPLICES SHALL DEVELOP IN TENSION AT
INTERSECTION WALL INTERSECTING R.C. COLUMN OR WALL
LEAST 125% OF THE SPLICED YIELD STRENGTH OF THE BAR NOT MORE THAN 50% OF THE BARS AT ANY ONE SECTION 180 DEG. HOOKS
Dbar
IS ALLOWED TO BE SPLICED THEREIN.
TYPICAL CONNECTION DETAIL OF MASONRY WALL

D+12db
135 DEG. HOOKS

4db OR 65mm LE
NOTES ON CONCRETE HOLLOW BLOCKS WALLS
6d

D
90 DEG. HOOKS b
1. UNLESS OTHERWISE SHOWN IN PLANS ALL CONCRETE HOLLOW BLOCKS AND CERAMIC BLOCKS SHALL BE REINFORCED Dbar
DOWEL BARS TO
AS SHOWN IN THE SCHEDULE OF CONCRETE HOLLOW BLOCKS AND CERAMIC BLOCK REINFORCEMENT. MATCH VERT. BARS
FLR. SLAB OR BEAM
2. PROVIDE 150mm X 300mm STIFFENER COLUMN REINFORCED WITH 4-12mmØ WITH 10mmØ TIES AT 150mm ON CENTER L1

12db
(DOWEL)

WHERE CONCRETE HOLLOW BLOCK TERMINATES AND AT EVERY 3.0M LENGTH OF CONCRETE HOLLOW BLOCK
1. ALL JOINTS AND CELLS
400

WALLS UNLESS NOTED IN STRUCTURAL PLANS. D

VERIFY ARCHITECTURAL

CONTAINING REINFORCING
BARS SHALL BE FILLED
WITH CONCRETE GROUT. MAIN BAR END HOOKS STIRRUP AND THE TIE HOOKS

NOTES ON CONCRETE HOLLOW BLOCKS WALLS REINFORCEMENTS 2. FOR REINFORCEMENTS SEE (ALL GRADES) (ALL GRADES)

CONSTRUCTION NOTES. ‘ +22. ‘ +22. BAR SIZE DIAMETER

‘ +22. ‘ +22.
BAR SIZE DIAMETER
BLOCK THICKNESS REINFORCEMENT NOTES (DEFORMED) (mm) (DEFORMED) (mm) D+2db
D+2db
(DOWEL)

HORIZONTAL LAPPED A. MINIMUM LAPS AT SPLICE= 0.25 M 1- Ø16 CONT. HOR. BARS 60 75 125 150 10 mmØ 40 125 85 100
10 mmØ
400

FOR FLOOR SLAB ONLY

75 mm 10mm Ø EVERY 3RD LEVEL 10mm Ø @ 600mm O.C B. PROVIDE RIGHT ANGLED REINFORCEMENT 12 mmØ 75 100 150 200 12 mmØ 50 165 115 115

AT CORNERS 0.92 m LONG 65 200 140 150

125 mm 16 mmØ
10mm Ø EVERY 3RD LEVEL 10mm Ø @ 600mm O.C 16 mmØ 95 125 175 250
C.WHERE CHB OR CER. BLK. WALL DOWELS
20 mmØ 115 300 165 300
150mm 10mm Ø EVERY 3RD LEVEL 10mm Ø @ 600mm O.C WITH THE SAME SIZE AS VER. OR HOR. 20 mmØ 115 150 200 300

REINFORCEMENT SHALL BE PROVIDED TYP. SECTION OF MASONRY 32 mmØ 150 335 230 405
25 mmØ 150 200 230 450
200 mm 12mm Ø EVERY 3RD LEVEL 10mm Ø @ 600mm O.C
PARTITION REINFORCEMENTS 28 mmØ 240 300 350 550

32 mmØ 300 335 450 600

REPUBLIC OF THE PHILIPPINES PROJECT NAME AND LOCATION: SHEET CONTENTS: DRAFTED: REVIEWED: SUBMITTED: RECOMMENDED: APPROVED: SET NO. SHEET NO.
DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS
MICHELLE A. COLBONGAN
REGION II GENERAL CONSTRUCTION NOTES ENGINEERING ASSISTANT
BASIC INFRASTRUCTURE PROGRAM (BIP)- MULTI- PURPOSE
ISABELA FOURTH BUILDINGS/FACILITIES TO SUPPORT SOCIAL SERVICES-
CONSTRUCTION OF MULTI-PURPOSE BUILDING, BARANGAY PREPARED: MARLON S. LUCAS ANACLETO SANTOS A. BUMAGAT JR. EMMANUEL A. MANSIBANG EVELYN C. COSTALES, Ph.D S 10
DISTRICT ENGINEERING OFFICE VILLA SANCHEZ, SAN GUILLERMO, ISABELA
BRGY. VILLA SANCHEZ, SAN GUILLERMO, ISABELA DONNE JOLLEE C. DUMELOD ENGINEER II CHIEF, PLANNING AND DESIGN SECTION ASSISTANT DISTRICT ENGINEER DISTRICT ENGINEER 2 7 20
QUEZON, SAN ISIDRO, ISABELA ENGINEER II DATE: DATE: DATE: DATE: