About Piezo Siwtches

Conventional electromechanical switches have moving parts that inevitably wear out.
The reliability of the electromechanical switches can be reduced by contaminants such as moisture and dust that will foul
contact points.

DISTINCTIVE FEATURES
The solution is a Piezo Switch with no moving parts.
The switch is not polarity sensitive: (+) and (-) wires can inversed without any risk.

How a Piezo switch works:

User Input /
Output Control surface transfers to the piezo disk creating an electrical
VDC5~24V pulse. This electrical signal is converted to an expected
electrical output through a customizable electronic circuit.
The duration of the electrical signal depends on the speed,
Load force and duration of actuation.
The output of the switch is closed for a specified pulse
duration depending on the electrical function chosen (see
The switch is not polarity sensitive:
next page).
(+) and (-) wires can inversed without any risk.

Main Applications:

Bath
Car wash
(IP68 sealing, customization)
(IP68 sealing, long life)
Shower
(IP68 sealing)

Marine Medical
(IP68 sealing, design) (easy to clean surface, no retention area)
 FINGER PRESSURE t<20s t>20s
ELECTRICAL FUNCTIONS

applied to switch 1

1 = pressure
0 = no pressure 0 t

OUTPUT
1
- Momentary NO (pulse)
No external power supply required
0 t
1
- Momentary NC (pulse)
No external power supply required
0 t
Up to 20s
1
- Momentary NO
prolongated pulse
No external power supply required 0 t
1
- Latching (ON - OFF)
Requires external power supply 0 t

1 = closed output 0 = open output

Wiring diagrams
Non-illuminated 1 LED * 2 LEDs 3 LEDs
RED RED
RED
RED
Momentary NO RED
RED RED
RED

A B A B A B A B A B A B

RED RED
RED
RED
Momentary NC RED
RED RED
RED

A B A B A B A B A B A B

RED RED
RED
Momentary NO RED
RED RED
prolongated pulse RED
RED

A B A B A B A B A B A B

BROWN BROWN BROWN

Latching (ON - OFF) BLACK

BLACK
BLACK
BLACK
BLACK
BLACK

BLUE BLUE BLUE

Legend: B = black, A = same colour as LED

* LED colour is indicated by the bottom of the product.
 Sealed to IP 68 and IP69K (switches mounted on panel)

Easy to clean metal surface

Very long life expectancy

SPECIFICATIONS
Ring or dot illumination

ENVIRONMENTAL SPECIFICATIONS MATERIALS

• Sealing : IP68 per IEC 529, IP69K per DIN 40050-9 • Case : aluminium, anodized
(switches mounted on panel or not) or stainless steel 316L
• Vibration resistance : 10-500 Hz / 10 g per IEC 60068-2-6 or brass, chrome plated
• Operating temperature : -40°C to +75°C • Multi-wire leads section AWG24
• EMC compatibility according to EN 61058-1 for the whole range length 300 mm, twisted by pair
• EMC compatibility according to EN 61000-4 & EN61000-6-2 for model • Cable, length 300 mm, section
1A (code 002) depending on switch model
• PC terminals : Gold or Tin plated

ELECTRICALANDGENERALSPECIFICATIONS
• Max. current/voltage rating : 200mA 5~24VAC/DC
• Switch resistance ON : 10 max.
• Switch resistance OFF : 5M min.
• Operating force : 6 to 15N
• Life expectancy : 50 million cycles
• LED consumption : Illuminated dot : 10mA - Illuminated ring : 20mA

SEALINGIP68 SEALINGIP69K
1 m

One-piece bushing
Epoxy sealed terminals
O-ring

Continuous immersion in water High pressure, high temperature wash down

IP68 test conditions IP69K test conditions
Continuous immersion in water . Pressure : 80 - 120 bars
(1m, 24 hours) . Distance : 15 cm
. Temperature : 80°C ± 5°C
. Flow : 14 - 16 l/mn
. Duration : 30 seconds per position

Dimensions: first dimensions are in mm while inches are shown as bracketed numbers.
Tolerance: The general tolerance for dimensions in this brochure is ± 0,3 (.012).
Dimensions, specifications and data shown in this brochure are subject to change without notice.
 PZ-
Housing: Marking:
Custom Markings Available
A =Aluminum
S =Stainless Steel 316L LED Colours:
Blank Non-illum.
Switch Size:
B Blue
PIEZO SWITCH

12 =12mm G Green
=16mm Switch Action: R Red

LATCHING & DOT ILLUM.

16
19 =19mm Y Yellow
M =Momentary Action (2 wire leads) White
22 =22mm W
L =Latching Action(3 wire leads only) Red/green
25 =25mm RG
30 =30mm Switch Status: RY Red/yellow
RB Red/blue
NO =Normally Open RW Red/white
Colours / Materials: NC =Normally Closed GB Green/blue

MOMENTARY
0 Natural anodized K =NO prolongated pulse GY Green/yellow
1 Blue anodized GW Green/white
2 Black anodized Input/Output: BY Blue/yellow
3 Green anodized 1 =200mA 24VAC/DC(standard) YW Yellow/white
5 Gold anodized 2 =1A 24VAC/DC 3A Red/green/blue
6 Red anodized 3B Red/green/yellow
B Stainless Steel 316L Illum. Options: 3D Red/green/white
3E Red/blue/yellow
Blank Non-illum. 3F Red/blue/white
R =Ring for operator 13.5 3G Red/yellow/white
R0 =Ring for operator 16.5 (22, 25, 30mm only) 3H Green/blue/yellow
Operator: D =Dot 3I Green/blue/white
Blank =Flat, operator heigh 12=1.50/ 16,19,22,25,30=1.30(non-illum.) Type of illum./ voltage: 3J Green/yellow/white
R1 =Flat, operator height 4.50(16mm only) 3K Blue/yellow/white
Blank Non-illum.
R2 =Flat, operator height 3.00(not available with ring illum.) Standard ring - 5VDC
A
R5 =Operator with finger location, height 12=1.5/ 16=4.50(non-illum.) Standard ring - 12VDC
N
R6 =Finger location, operator height 3.00(not available with ring illum.) Standard ring - 24VDC
K
RA =Chamfer, operator height 3.00(19mm only)
RY =Chamfer, operator height 4.50 (available with thin or large ring illum. only)
RZ =Flat, operator height 4.50 (available with thin or large ring illum. only)
The operator can be customized

LED Colours:

B G R Y W
Colours / Materials:

0 1 2 3 5 6 B

Notice: The Latching fuctions 3 Wire leads only.

The 12mm switch NO only. NOT for 3 wire leads

Mounting accessories standard hardware supplied :1 hex nut and 1 O-ring

Packaging unit: 20 pieces

For options not listed above, please contact CHINTRONIX.

The appearance of the products listed on this file, color, parameters are for reference only, issued a kind of CHINTRONIX
shall prevail.
CHINTRONIX reserves the right to modify or cancel the relevant parameters of this file does not advance notice.
If in doubt, please contact customer service hotline.
 PZA12 0 Z F

SERIES
Ø12.20
(.480 DIA) Bushing / operator

PIEZO SWITCH
All models with Ø 12 bushing
R5 Operator with finger location.
Shown with flying lead terminals. Blank Flat operator, height 1,20(.047)

Non-illuminated

Ø17.00 Ø13.00

(.059)
1.50
(.669DIA) (.512DIA)

Flat
15.50
(.610)

Ø12X1.0
(Ø.472X1.0)
Finger location AWG24
30CM

R5
PZA125ZF1NOM
 PZA16 0 Z F

SERIES
Ø16.20
(.637 DIA) Bushing / operator
All models with Ø 16 bushing
PIEZO SWITCH

R1 Flat operator, height 4,50(.177)

Shown with flying lead terminals. R5 Operator with finger location,
height 4,50(.177) (non-illuminated)
Blank Flat operator, height 1,30(.051)

Non-illuminated
Ø18.00 Ø13.00
(.708DIA) (.512DIA)

(.177)
4.50
(.051)
Ø18.00

1.30
(.708DIA)

Flat

20.00
(.787)
14.00
(.551)

Ø16.00x1.00 SI
(.630DIAx1.00 IS)

AWG26
30CM

(.197)
5.00
Finger location

R1 R5

PZA166F1NOM

Dot-illuminated
(.051)

Ø18.00
1.30

(.708DIA)
Flat LED
14.00
(.551)

Ø16.00x1.00 SI Ø3.00 PUSH

(.630DIAx1.00 IS) (.118DIA) ZONE

3.70
AWG26
(.146)
30CM

PZS16BFD1NOMKB

Ring illuminated
Ø16.00x1.00 SI
(.630DIAx1.00 IS)
Ø13.50
4.50 5.00
(.177) (.197) (.531DIA)

Flat operator, height 4,50 (.177)

(.708DIA)
Ø18.00

AWG26
30CM
1.20
(.047)
20.00
(.787)

PZA160R1R1NOMKG
 PZA19 0 Z F

SERIES
Ø19.20
(.756 DIA)
Bushing / operator
All models with Ø 19 bushing

PIEZO SWITCH
R2 Flat operator, height 3,00(.118)
Shown with flying lead terminals. RA Operator with chamfer,
height 3,00(.118)
Blank Flat operator, height 1,30(.051)

Non-illuminated

Ø22.00
Flat Ø22.00 45
°

(.079)
(.118)
(.866DIA)

2.00
3.00
(.051)
(.866DIA)

1.30
18.00

20.00
(.709)

(.787)
Chamfer Ø19.00x1.00 SI
(.748DIAx1.00 IS)

AWG26 AWG26
30CM 30CM

R2 RA
PZA192F1NOM

Dot-illuminated

Ø22.00
(.051)

(.866DIA)
1.30

LED
Flat Ø3.00
(.118DIA)
PUSH
ZONE
18.00
(.709)

Ø19.00x1.00 SI
(.748DIAx1.00 IS) 6.50
(.256)

AWG26
30CM

PZS19BFD1NOMKR

Ring illuminated Ø22.00 45

°
(.118)

(.079)

(.866DIA)
3.00

2.00
20.00
(.787)

Flat
Ø19.00x1.00 SI
(.748DIAx1.00 IS)

AWG26
(.047)

(.047)
1.20

1.20

30CM
Chamfer
(.531DIA)

(.531DIA)
Ø13.50

Ø13.50

PZS19BRA1NOMKR R2 RA
 PZA22 0 Z F

SERIES

Ø22.20
(.874 DIA)
Bushing / operator
All models with Ø 22 bushing
PIEZO SWITCH

R2 Flat operator, height 3,00(.118) (non-illum.)

R6 Finger location,operator height 3,00(.118) (non-illum.)
Shown with flying lead terminals. RY With chamfer, operator height 4,5 mm (.177).
or large illuminated ring only
RZ Flat, operator height 4,5 mm (.177).
or large illuminated ring only
Blank Flat actuator, height 1,30(.051)

Non-illuminated

Ø25.00 Ø28.00 Ø22.00

(.984DIA) (1.102DIA) (.866DIA)

Flat

(.051)
1.30
19.50
(.768)

(.118)
3.00
Ø22.00x1.00 SI
Finger location (.866DIAx1.00 IS)

AWG26
Ø20.50 Ø20.50 30CM
(.807DIA) (.807DIA)

R2 R6

PZA226F1NOM

Dot illuminated Ø25.00

(.984DIA)
Ø28.00
(1.102DIA)
Ø22.00
(.866DIA)
(.051)
1.30

19.50
(.768)
19.50
(.768)

(.118)
3.00

Flat Ø22.00x1.00 SI
(.866DIAx1.00 IS)
AWG26
30CM

Finger location LED

PUSH Ø3.00 PUSH PUSH
ZONE (.118DIA) ZONE ZONE

6.50
(.256)

PZS22BFD1NOMNR R2 R6

Ring illuminated 30°

Ø28.00 2.00
(1.102DIA) (.079)
(.138)
3.50
20.00
(.787)

(.177)
4.50

Flat Ø22.00x1.00 SI
(.866DIAx1.00 IS)
AWG26
30CM
Ø20.50
(.807DIA)
Chamfer
(.126)

(.185)

(.126)

(.185)
3.20

4.70

3.20

4.70
(.709DIA)

(.531DIA)

(.709DIA)

(.531DIA)
Ø16.50

Ø13.50

Ø16.50

Ø13.50

PZS22BRYR01NOMKR
RZ RY
 PZA25 0 Z F

SERIES

Ø25.20
(.992 DIA)
Bushing / actuator
All models with Ø 25 bushing

PIEZO SWITCH
R2 Flat operator, height 3,00(.118) (non-illum.)
R6 Finger location,operator height 3,00(.118) (non-illum.)
Shown with flying lead terminals. RY With chamfer, operator height 4,5 mm (.177).
or large illuminated ring only
RZ Flat, operator height 4,5 mm (.177).
or large illuminated ring only
Blank Flat actuator, height 1,30(.051)

Non-illuminated

Ø28.00 Ø28.00 Ø22.00

(1.102DIA) (1.102DIA) (.866DIA)

Flat

(.051)
1.30
19.50
(.768)

(.118)
3.00
Ø25.00x1.00 SI
Finger location (.984DIAx1.00 IS)

AWG26
Ø23.50 Ø23.50 30CM
(.925DIA) (.925DIA)

R2 R6

PZS22BF1NOM

Dot illuminated Ø28.00

(.984DIA)
Ø28.00
(1.102DIA)
Ø22.00
(.866DIA)
(.051)
1.30

19.50
(.768)
19.50
(.768)

(.118)
3.00

Flat Ø25.00x1.00 SI
(.984DIAx1.00 IS)
AWG26
30CM

Finger location LED

PUSH Ø3.00 PUSH PUSH
ZONE (.118DIA) ZONE ZONE

6.50
(.256)

PZS25BFD1NOMNR R2 R6

Ring illuminated 30°

Ø30.00 2.00
(1.181DIA) (.079)
(.138)
3.50
20.00
(.787)

(.177)
4.50

Flat Ø25.00x1.00 SI
(.984DIAx1.00 IS)
AWG26
30CM
Ø23.50
(.925DIA)
Chamfer
(.126)

(.185)

(.126)

(.185)
3.20

4.70

3.20

4.70
(.709DIA)

(.531DIA)

(.709DIA)

(.531DIA)
Ø16.50

Ø13.50

Ø16.50

Ø13.50

PZS25BRYR1NOMKB
RZ RY
 PZA30 0 Z F

SERIES
Ø30.20
(1.189 DIA)
Bushing / actuator
All models with Ø 30 bushing
PIEZO SWITCH

R2 Flat operator, height 3,00(.118) (non-illum.)

Shown with flying lead terminals. R6 Finger location,operator height 3,00(.118) (non-illum.)
RY With chamfer, operator height 4,5 mm (.177).
or large illuminated ring only
RZ Flat, operator height 4,5 mm (.177).
or large illuminated ring only
Blank Flat actuator, height 1,30(.051)

Non-illuminated
Ø33.00 Ø33.00 Ø27.00
(1.299DIA) (1.299DIA) (1.063DIA)

Flat
(.051)
1.30
19.50
(.768)

(.118)
3.00
Ø30.00x1.00 SI
(1.181DIAx1.00 IS)
Chamfer AWG26
Ø28.50 Ø28.50 30CM
(1.122DIA) (1.122DIA)

R2 R6

PZS30BF1NOM

Dot-illuminated Ø33.00
(1.299DIA)
Ø33.00
(1.299DIA)
Ø27.00
(1.063DIA)
(.051)
1.30

19.50
(.768)
19.50
(.768)

(.118)
3.00

Ø30.00x1.00 SI
Flat (1.181DIAx1.00 IS)
AWG26
30CM

LED
Finger location PUSH Ø3.00
(.118DIA)
PUSH PUSH
ZONE ZONE ZONE

6.50
(.256)

PZS30BFD1NOMKR R2 R6

3.50 30°
Ring illuminated
Ø35.00
(1.378DIA) (.138)
(.138)
3.50
20.00
(.787)

(.177)
4.50

Flat Ø30.00x1.00 SI
(1.181DIAx1.00 IS)
AWG26
30CM
Ø28.50
(1.122DIA)
Chamfer
(.126)

(.185)

(.126)

(.185)
3.20

4.70

3.20

4.70
(.709DIA)

(.531DIA)

(.709DIA)

(.531DIA)
Ø16.50

Ø13.50

Ø16.50

Ø13.50

PZS30BFRY1NOMKRGR RZ RY