ENGLISH

SUBWOOFER
CAISSON DE GRAVE

ESPAŃOL FRANÇAIS
CS-AW7020 CS-AW7040
CS-AW7220 CS-AW7240

CS-AW7020 CS-AW7220
CS-AW7040 CS-AW7240

For Customer Use:

Enter below the Model No, and Serial
No, which is located either on the rear
or bottom of the speaker unit. Retain
this information for future reference.
Model No.
Serial No.
INSTRUCTION MANUAL
MANUEL D'INSTRUCTIONS LVT1743-001A
MANUAL DE INSTRUCCIONES
 Thank you for purchasing the ARSENAL Car Stereo Speaker. These Speakers can be
mounted in the trunk of your vehicle. For the secure installation and perfect operation
of your speakers, please read the following carefully.
ENGLISH

Parts

2. Screw x 10 3. Jump

1. Grille

4. Fuse (10A) x 2 5. Hexagon socket

screw keys

For proper installation and use

1.Before connecting the speakers to the amplifier, confirm that the power has been
turned off. The click noise generated by the connection if the power is on may
damage the speakers.
2.The amplifier and speakers should be connected between corresponding terminals,
i.e. left to left, and right to right, as well as "+" to "+", and "–" to "–". Connection with
reversed polarity will degrade the quality of stereo reproduction.
3.Do not subject the speakers to excessive input. The power handling capacity of the
CS-AW7020/CS-AW7040/CS-AW7220/CS-AW7240 is 600 watts (R.M.S. MUSIC
POWER). Any excessive input may damage the speakers.
4.The CS-AW7020/CS-AW7040/CS-AW7220/CS-AW7240 has an impedance of 2Ω
,4Ω,8Ω. Make sure that the output impedance of the amplifier's speaker terminal is
rated at 2Ω,4Ω,8Ω.
5.When cleaning the speakers, use a soft cloth and wipe the surface gently. Do not
apply thinner or solvent.
6.Be sure to carefully follow the instructions for:
Cable Connections
Fuse Replacement
Switching the Impedance Selector
Subwoofer Mounting and Smart Trim Ring Installation
Consult Page 19 of this Instruction Manual for details on these procedures.

-2-
Dual 4 Ω Application Diagrams
JUMPER JUMPER

ENGLISH
1 Mono Amplifier 1 Mono Amplifier
1 Subwoofer 1 Subwoofer
Jumper set to Series Jumper set to Parallel
8Ω(4Ω+4Ω) Load SERIES PARALLEL 8Ω(4Ω+4Ω) Load SERIES PARALLEL
Jumper Plug
Jumper Plug

Input Bi-Amp Input Input Bi-Amp Input

+ - Only + - + - Only + -

Mono Mono
4Ω 4Ω 4Ω 4Ω
8Ω 2Ω

*JUMPER is Removed *JUMPER is Removed

Bi-Amp Configuration 2 Mono Amplifiers
1 2ch Amplifier 1 Subwoofer Jumper is Removed 4Ω Load
1 Subwoofer
Jumper is Removed
4Ω Load SERIES PARALLEL SERIES PARALLEL

Input Bi-Amp Input

Mono Input Bi-Amp Input
Stereo + - Only + - + - Only + -
4Ω

Mono
4Ω 2-Chan
4Ω

JUMPER JUMPER
1 Mono Amplifier
2 Subwoofers
Jumper set to Series
Subwoofers wired in Parallel SERIES PARALLEL SERIES PARALLEL
4Ω Load Jumper Plug Jumper Plug

Input Bi-Amp Input Input Bi-Amp Input

+ - Only + - + - Only + -

Mono
4Ω 8Ω 4Ω 4Ω 8Ω 4Ω
4Ω

JUMPER JUMPER JUMPER

1 Mono Amplifier
3 Subwoofers
Jumper set to Series
Subwoofers wired in Parallel SERIES PARALLEL SERIES PARALLEL SERIES PARALLEL
2.6Ω Load Jumper Plug Jumper Plug Jumper Plug

Input Bi-Amp Input Input Bi-Amp Input Input Bi-Amp Input

+ - Only + - + - Only + - + - Only + -

Mono
4Ω 8Ω 4Ω 4Ω 8Ω 4Ω 4Ω 8Ω 4Ω
2.6Ω

JUMPER JUMPER JUMPER JUMPER

1 Mono Amplifier
4 Subwoofers
Jumper set to Series
Subwoofers wired in Parallel SERIES PARALLEL SERIES PARALLEL SERIES PARALLEL SERIES PARALLEL
2Ω Load Jumper Plug Jumper Plug Jumper Plug Jumper Plug

Input Bi-Amp Input Input Bi-Amp Input Input Bi-Amp Input Input Bi-Amp Input
+ - Only + - + - Only + - + - Only + - + - Only + -

Mono
4Ω 8Ω 4Ω 4Ω 8Ω 4Ω 4Ω 8Ω 4Ω 4Ω 8Ω 4Ω
2Ω

-3-
 Dual 2 Ω Application Diagrams
JUMPER JUMPER
ENGLISH

1 Mono Amplifier 1 Mono Amplifier

1 Subwoofer 1 Subwoofer
Jumper set to Series Jumper set to Parallel
4Ω(2Ω+2Ω) Load SERIES PARALLEL 4Ω(2Ω+2Ω) Load SERIES PARALLEL
Jumper Plug
Jumper Plug

Input Bi-Amp Input Input Bi-Amp Input

+ - Only + - + - Only + -

Mono Mono
2Ω 2Ω 2Ω 2Ω
4Ω 1Ω

*JUMPER is Removed *JUMPER is Removed

Bi-Amp Configuration 2 Mono Amplifiers
1 2ch Amplifier 1 Subwoofer Jumper is Removed 2Ω Load
1 Subwoofer
Jumper is Removed
2Ω Load SERIES PARALLEL SERIES PARALLEL

Input Bi-Amp Input

Mono Input Bi-Amp Input
Stereo + - Only + - + - Only + -
2Ω

Mono
2Ω 2-Chan
2Ω

JUMPER JUMPER
1 Mono Amplifier
2 Subwoofers
Jumper set to Series
Subwoofers wired in Parallel SERIES PARALLEL SERIES PARALLEL
2Ω Load Jumper Plug Jumper Plug

Input Bi-Amp Input Input Bi-Amp Input

+ - Only + - + - Only + -

Mono
2Ω 4Ω 2Ω 2Ω 4Ω 2Ω
2Ω

JUMPER JUMPER JUMPER

1 Mono Amplifier
3 Subwoofers
Jumper set to Series
Subwoofers wired in Parallel SERIES PARALLEL SERIES PARALLEL SERIES PARALLEL
1.3Ω Load Jumper Plug Jumper Plug Jumper Plug

Input Bi-Amp Input Input Bi-Amp Input Input Bi-Amp Input

+ - Only + - + - Only + - + - Only + -

Mono
2Ω 4Ω 2Ω 2Ω 4Ω 2Ω 2Ω 4Ω 2Ω
1.3Ω

JUMPER JUMPER JUMPER JUMPER

1 Mono Amplifier
4 Subwoofers
Jumper set to Series
Subwoofers wired in Parallel SERIES PARALLEL SERIES PARALLEL SERIES PARALLEL SERIES PARALLEL
1Ω Load Jumper Plug Jumper Plug Jumper Plug Jumper Plug

Input Bi-Amp Input Input Bi-Amp Input Input Bi-Amp Input Input Bi-Amp Input
+ - Only + - + - Only + - + - Only + - + - Only + -

Mono
2Ω 4Ω 2Ω 2Ω 4Ω 2Ω 2Ω 4Ω 2Ω 2Ω 4Ω 2Ω
1Ω

-4-
 To install the sealed enclosure
When the speaker cannot be attached in the car, make the sealed enclosure as recommended in the table below—20 mm (3/4 inch) MDF is also
recommended for the enclosure materials.
CS-AW7020 / CS-AW7040 CS-AW7220 / CS-AW7240
A 15-13/32 inch (391.7 mm) 16-13/32 inch (417.1 mm)
B 15-13/32 inch (391.7 mm) 16-13/32 inch (417.1 mm)
C 11-13/32 inch (290.1 mm) 13-29/32 inch (353.6 mm)
D 9-4/32 inch (232 mm) 10-14/32 inch (275.9 mm)

ENGLISH
E 9-23/32 inch (247 mm) 11-10/32 inch (295 mm)
F 4/32 inch (3 mm) 4/32 inch (3 mm)
3 3
G 1.57 ft (0.045 m ) 2.17 ft3 (0.062 m3)
Front & Rear Baffle Boards (x 2)
C B Top & Bottom Sides (x 2)

G : Internal Volume
A

Left & Right Sides (x 2)

Mounting Hole
Dimension
* Screw: Dia. 4mm x 50mm (x 8) (supplied)

To install the ported enclosure

When the speaker cannot be attached in the car, make the sealed enclosure as recommended in the table below—20 mm (3/4 inch) MDF is also
recommended for the enclosure materials.
CS-AW7020 / CS-AW7040 CS-AW7220 / CS-AW7240
A 15-13/32 inch (391.7 mm) 15-13/32 inch (391.7 mm)
B 18-13/32 inch (467.9 mm) 18-13/32 inch (467.9 mm)
C 13-13/32 inch (340.9 mm) 15-13/32 inch (391.7 mm)
D 9-23/32 inch (247 mm) 10-14/32 inch (275.9 mm)
E 9-23/32 inch (247 mm) 11-10/32 inch (295 mm)
F 4/32 inch (3 mm) 4/32 inch (3 mm)
G 1 inch (25.4 mm) 1 inch (25.4 mm)
H 13 inch (330.2 mm) 14 inch (355.6 mm)
I 13-19/32 inch (345.4 mm) 13-6/32 inch (335.3 mm)
Front & Rear Baffle Boards (x 2) J 1.85 ft3 (0.052 m3) 2.54 ft3 (0.072 m3)

C B Top & Bottom Sides (x 2)

J : Internal Volume

A Left & Right Sides (x 2)

G

I H
Mounting Hole
Dimension
* Screw: Dia. 4mm x 50mm (x 8) (supplied) - 5-
 CS-AW7020 CS-AW7040
Parameters NOTES
parallel series parallel series
Nominal Impedance (Ω) 2Ω + 2Ω 4Ω + 4Ω
SPL (dB,1W/1M) 83.49 dB 83.54 dB 84.02 dB 84.12 dB SPL : Sound pressure level
Displacement (Liter) 0.123 ft3
Hole Cutout Diameter (inch) Dia. 9 - 6/32 inch
(mm) ( 233 mm )
Mounting Depth (inch) 6 - 14/32 inch
(mm) ( 163.5 mm )
ENGLISH

Re (Ω) 0.98 Ω 3.83 Ω 1.92 Ω 7.6 Ω Re : DC voice coil resistance

BL : Product of Flux density and

BL (T.M) 6.85 13.75 8.68 17.21
Effective Voicecoil-wire length
Vas : Volume of air equal to the driver
Vas (Liter) 17.08 L 16.98 L 18.08 L 18.28 L
compliance
Vas (CuFt) 0.6 ft3 0.599 ft3 0.64 ft3 0.65 ft3
Me (g) 145.986 g 147.109 g 124.084 g 122.443 g Me : Effective mass
D (mm) Dia. 202 mm D : Effective cone diameter
Fs (Hz) 39.6 Hz 39.5 Hz 41.7 Hz 41.8 Hz Fs : Driver free air resonance
Qms : Q of driver at Fs considering
Qms 10.261 10.282 9.021 9.169
only non-electrical resistance
Qes : Q of driver at Fs considering
Qes 0.756 0.74 0.83 0.824
only electrical resistance
Qts 0.704 0.691 0.76 0.756 Qts : Total Q of driver at Fs
Pe[max.] : Maximum continuous input
Pe [max.] (W) 600 W
power
Xmax. : Maximum effective voicecoil
Xmax.(mm) 14.95 mm 14.8 mm
travel without distortion
Freq.Responce (Hz) 25 ~500 Hz
Magnet Mass (oz) 65.4 oz
(g) ( 1854.1 g )
Voice Coil(Aluminum)Dia.(inch) Dia. 2 - 5/32 inch Dia. 2 - 4/32 inch
(mm) 54.5 mm 53.59 mm
Hvc (mm) 39.9 mm 39.6 mm Hvc : Voice coil Height
Hag (mm) 10 mm Hag : Gap Height
CS-AW7220 CS-AW7240
Parameters NOTES
parallel series parallel series
Nominal Impedance (Ω) 2Ω + 2Ω 4Ω + 4Ω
SPL (dB,1W/1M) 85.13 dB 85.2 dB 85.87 dB 85.65 dB SPL : Sound pressure level
Displacement (Liter) 0.18 ft3
Hole Cutout Diameter (inch) Dia. 10 - 29/32 inch
(mm) ( 277 mm )
Mounting Depth (inch) 7 - 6/32 inch
(mm) ( 182.5 mm )
Re (Ω) 0.98 Ω 3.84 Ω 1.94 Ω 7.61 Ω Re : DC voice coil resistance

BL : Product of Flux density and

BL (T.M) 6.84 13.72 9.56 19.14
Effective Voicecoil-wire length
Vas : Volume of air equal to the driver
Vas (Liter) 38.7 L 38.76 L 35.23 L 35.05 L
compliance
Vas (CuFt) 1.37 ft3 1.37 ft3 1.24 ft3 1.24 ft3
Me (g) 171.854 g 172.934 g 157.028 g 157.336 g Me : Effective mass
D (cm) Dia. 246 mm D : Effective cone diameter
Fs (Hz) 34.6 Hz 34.5 Hz 37.9 Hz 38 Hz Fs : Driver free air resonance
Qms : Q of driver at Fs considering
Qms 10.277 10.089 8.931 9.014
only non-electrical resistance
Qes : Q of driver at Fs considering
Qes 0.786 0.765 0.794 0.781
only electrical resistance
Qts 0.73 0.711 0.73 0.719 Qts : Total Q of driver at Fs
Pe[max.] : Maximum continuous input
Pe [max.] (W) 600 W
power
Xmax. : Maximum effective voicecoil
Xmax.(mm) 14.95 mm 14.8 mm
travel without distortion
Freq.Responce (Hz) 23 ~500 Hz
Magnet Mass (oz) 86.2 oz
(g) ( 2443.7 g )
Voice Coil(Aluminum)Dia.(inch) Dia. 2 - 5/32 inch Dia. 2 - 4/32 inch
(mm) ( 54.5 mm ) ( 53.59 mm )
Hvc (mm) 39.9 mm 39.6 mm Hvc : Voice coil Height
Hag (mm) 10 mm Hag : Gap Height

-6-
Nous vous remercions pour I'achat d'un haut-parleur auto stéréo de ARSENAL dans
le coffre de votre véhicule. Pour un montage sûr et un fonctionnement parfait de ce
haut-parleur, il est conseillé de lire attentivement ce qui suit.

Parts

FRANÇAIS
2. Screw x 10 3. Jump

1. Grille

4. Fuse (10A) x 2 5. Hexagon socket

screw keys

Montage et utilisation corrects

1.Vérifier que l'alimentation est coupée avant de raccorder les haut-parleurs à
l'amplificateur. Les craquements produits par le raccordement lors que l'alimentation
est fournie peuvent endomma ger les haut-parleurs.
2.Raccorder les bornes correspondantes de l’amplificateur et les haut-parleurs,
c'est-à-dire, gauche à gauche, droit à droite, de même que “+” à “+” et “–” à “–”. Un
raccordement effectué en inversant les polarités réduira la qualité de la reproduction
sonore stéréo-phonique.
3.Ne pas appliquer un niveau d'entrée excessif aux haut-parleurs. La puissance
d'entrée admissible pour les haut-parleurs
CS-AW7020/CS-AW7040/CS-AW7220/CS-AW7240 est de 600 watts (puissance
musicale R.M.S.). Tout signal d'entrée excessif risque de les endommager.
4.Les haut-parleurs CS-AW7020/CS-AW7040/CS-AW7220/CS-AW7240 ont une
impédance de 2Ω,4Ω,8Ω. ll faut par conséquent s'assurer que l'impédance de sortie
aux bornes de haut-parleur de l'amplificateur soit aussi de 2Ω,4Ω,8Ω.
5.Nettoyer le haut-parleur en le frottant légèrement à l'aide d'un chiffon doux. Ne
jamais utiliser de solvants ni de détergents.
6.Veuillez suivre attentivement les instructions suivantes pour:
Connections de Câble
Remplacement de Fusible
Changement de la Sélection d'Impédance
Montage du Subwoofer et Installation Pratique de la Moulure de Finition
Consultez la Page 19 de ce Manuel d'Instruction pour les détails de cesprocédures.
-7-
 Diagrammes d’application duale 4Ω
JUMPER JUMPER
1 amplificateur mono 1 amplificateur mono
1 (un) caisson de basse 1 (un) caisson de basse
Cavalier branché en Série Cavalier branché en Parallèle
Impédance de charge de SERIES PARALLEL Impédance de charge de SERIES PARALLEL
8Ω(4Ω+4Ω) Jumper Plug 8Ω(4Ω+4Ω) Jumper Plug

Input Bi-Amp Input Input Bi-Amp Input

+ - Only + - + - Only + -
FRANÇAIS

Mono Mono
4Ω 4Ω 4Ω 4Ω
8Ω 2Ω

*JUMPER is Removed Configuration en double amplification

1 amplificateur mono 2 amplificateurs mono *JUMPER is Removed
1 (un) caisson de basse 1 (un) caisson de basse Cavalier débranché
Cavalier branché en Parallèle Impédance de charge de 4Ω
Impédance de charge de 8Ω(4Ω+4Ω) SERIES PARALLEL
SERIES PARALLEL

Input Bi-Amp Input

Stereo + - Only + -
Mono Input Bi-Amp Input
+ - Only + -
4Ω

4Ω 2-Chan
Mono

4Ω
JUMPER JUMPER
1 amplificateur mono
2 (deux) caissons de basse
Cavalier branché en Série
Subwoofers wired in Parallel SERIES PARALLEL SERIES PARALLEL
Impédance de charge de 4Ω Jumper Plug Jumper Plug

Input Bi-Amp Input Input Bi-Amp Input

+ - Only + - + - Only + -

Mono
4Ω 8Ω 4Ω 4Ω 8Ω 4Ω
4Ω

JUMPER JUMPER JUMPER

1 amplificateur mono
3 (trois) caissons de basse
Cavalier branché en Série
Subwoofers wired in Parallel SERIES PARALLEL SERIES PARALLEL SERIES PARALLEL
Impédance de charge de 2.6Ω Jumper Plug Jumper Plug Jumper Plug

Input Bi-Amp Input Input Bi-Amp Input Input Bi-Amp Input

+ - Only + - + - Only + - + - Only + -

Mono
4Ω 8Ω 4Ω 4Ω 8Ω 4Ω 4Ω 8Ω 4Ω
2.6Ω

JUMPER JUMPER JUMPER JUMPER

1 amplificateur mono
4 (quatre) caissons de basse
Cavalier branché en Série
Subwoofers wired in Parallel SERIES PARALLEL SERIES PARALLEL SERIES PARALLEL SERIES PARALLEL
Impédance de charge de 2Ω Jumper Plug Jumper Plug Jumper Plug Jumper Plug

Input Bi-Amp Input Input Bi-Amp Input Input Bi-Amp Input Input Bi-Amp Input
+ - Only + - + - Only + - + - Only + - + - Only + -

Mono
4Ω 8Ω 4Ω 4Ω 8Ω 4Ω 4Ω 8Ω 4Ω 4Ω 8Ω 4Ω
2Ω

-8-
Diagrammes d’application duale 2Ω
JUMPER JUMPER
1 amplificateur mono 1 amplificateur mono
1 (un) caisson de basse 1 (un) caisson de basse
Cavalier branché en Série Cavalier branché en Parallèle
Impédance de charge de SERIES PARALLEL Impédance de charge de SERIES PARALLEL
4Ω(2Ω+2Ω) Jumper Plug 4Ω(2Ω+2Ω) Jumper Plug

Input Bi-Amp Input Input Bi-Amp Input

+ - Only + - + - Only + -

FRANÇAIS
Mono Mono
2Ω 2Ω 2Ω 2Ω
4Ω 1Ω

*JUMPER is Removed Configuration en double amplification

1 amplificateur mono 2 amplificateurs mono *JUMPER is Removed
1 (un) caisson de basse 1 (un) caisson de basse Cavalier débranché
Cavalier branché en Parallèle Impédance de charge de 2Ω
Impédance de charge de 4Ω(2Ω+2Ω) SERIES PARALLEL
SERIES PARALLEL

Input Bi-Amp Input

Stereo + - Only + -
Mono Input Bi-Amp Input
+ - Only + -
2Ω

2Ω 2-Chan
Mono

2Ω
JUMPER JUMPER
1 amplificateur mono
2 (deux) caissons de basse
Cavalier branché en Série
Subwoofers wired in Parallel SERIES PARALLEL SERIES PARALLEL
Impédance de charge de 2Ω Jumper Plug Jumper Plug

Input Bi-Amp Input Input Bi-Amp Input

+ - Only + - + - Only + -

Mono
2Ω 4Ω 2Ω 2Ω 4Ω 2Ω
2Ω

JUMPER JUMPER JUMPER

1 amplificateur mono
3 (trois) caissons de basse
Cavalier branché en Série
Subwoofers wired in Parallel SERIES PARALLEL SERIES PARALLEL SERIES PARALLEL
Impédance de charge de 1.3Ω Jumper Plug Jumper Plug Jumper Plug

Input Bi-Amp Input Input Bi-Amp Input Input Bi-Amp Input

+ - Only + - + - Only + - + - Only + -

Mono
2Ω 4Ω 2Ω 2Ω 4Ω 2Ω 2Ω 4Ω 2Ω
1.3Ω

JUMPER JUMPER JUMPER JUMPER

1 amplificateur mono
4 (quatre) caissons de basse
Cavalier branché en Série
Subwoofers wired in Parallel SERIES PARALLEL SERIES PARALLEL SERIES PARALLEL SERIES PARALLEL
Impédance de charge de 1Ω Jumper Plug Jumper Plug Jumper Plug Jumper Plug

Input Bi-Amp Input Input Bi-Amp Input Input Bi-Amp Input Input Bi-Amp Input
+ - Only + - + - Only + - + - Only + - + - Only + -

Mono
2Ω 4Ω 2Ω 2Ω 4Ω 2Ω 2Ω 4Ω 2Ω 2Ω 4Ω 2Ω
1Ω

-9-
 Pour installer l’enceinte hermétique
Si le haut-parleur ne peut pas être fixé directement dans cette voiture, fabriquez une enceinte hermétique de façon recommandéeà l’aide des
spécifications données dans le tableau ci-dessous; le
CS-AW7020 / CS-AW7040 CS-AW7220 / CS-AW7240
MDF—20 mm (3/4 pouce) est recommandé pour le matériau
A 15-13/32 inch (391.7 mm) 16-13/32 inch (417.1 mm)
de l’enceinte.
B 15-13/32 inch (391.7 mm) 16-13/32 inch (417.1 mm)
C 11-13/32 inch (290.1 mm) 13-29/32 inch (353.6 mm)
D 9-4/32 inch (232 mm) 10-14/32 inch (275.9 mm)
E 9-23/32 inch (247 mm) 11-10/32 inch (295 mm)
F 4/32 inch (3 mm) 4/32 inch (3 mm)
3 3
G 1.57 ft (0.045 m ) 2.17 ft3 (0.062 m3)
Écrans acoustiques avant et arrière (x 2)
C B
FRANÇAIS

Faces supérieure et
inférieure (x 2)

G : Volume interne
A

Faces gauche et
droite (x 2)

Faces gauche
et droite (x 2)
* Vis: Dia. 4mm x 50mm (x 8) (fournis)

Pour installer l’enceinte hermétique

Si le haut-parleur ne peut pas être fixé directement dans cette voiture, fabriquez une enceinte hermétique de façon recommandéeà l’aide des
spécifications données dans le tableau ci-dessous; le
CS-AW7020 / CS-AW7040 CS-AW7220 / CS-AW7240
MDF—20 mm (3/4 pouce) est recommandé pour le matériau
de l’enceinte. A 15-13/32 inch (391.7 mm) 15-13/32 inch (391.7 mm)
B 18-13/32 inch (467.9 mm) 18-13/32 inch (467.9 mm)
C 13-13/32 inch (340.9 mm) 15-13/32 inch (391.7 mm)
D 9-23/32 inch (247 mm) 10-14/32 inch (275.9 mm)
E 9-23/32 inch (247 mm) 11-10/32 inch (295 mm)
F 4/32 inch (3 mm) 4/32 inch (3 mm)
G 1 inch (25.4 mm) 1 inch (25.4 mm)
H 13 inch (330.2 mm) 14 inch (355.6 mm)
I 13-19/32 inch (345.4 mm) 13-6/32 inch (335.3 mm)
Écrans acoustiques avant et arrière (x 2) J 1.85 ft3 (0.052 m3) 2.54 ft3 (0.072 m3)

C B
Faces supérieure et
inférieure (x 2)

J : Volume interne

A Faces gauche et
G droite (x 2)

I H
Faces gauche
et droite (x 2)
* Vis: Dia. 4mm x 50mm (x 8) (fournis) - 10 -
 CS-AW7020 CS-AW7040
Paramètres REMARQUES
parallel series parallel series
Impédance nominale (Ω) 2Ω + 2Ω 4Ω + 4Ω
SPL (dB,1W/1M) 83.49 dB 83.54 dB 84.02 dB 84.12 dB SPL : Niveau de pression sonore
Déplacement (Liter) 0.123 ft3
Diamètre du tuou de découpe (pouces) Dia. 9 - 6/32 inch
(mm) ( 233 mm )
Profondeur de montage (pouces) 6 - 14/32 inch
(mm) ( 163.5 mm )
Re : Résistance de la bobine mobile
Re (Ω) 0.98 Ω 3.83 Ω 1.92 Ω 7.6 Ω
en CC
BL : Produit de la densité de flux et de
BL (T.M) 6.85 13.75 8.68 17.21 la longueur efficace de fil de la bobine
mobile
Vas : Volume d'air égal à la conformité
Vas (Iitre) 17.08 L 16.98 L 18.08 L 18.28 L

FRANÇAIS
de l'excitateur
Vas (CuFt) 0.6 ft3 0.599 ft3 0.64 ft3 0.65 ft3
Me (g) 145.986 g 147.109 g 124.084 g 122.443 g Me : Masse effective
D (mm) Dia. 202 mm D : Diamètre effectif du cône
Fs : Résonance à l'air libre de
Fs (Hz) 39.6 Hz 39.5 Hz 41.7 Hz 41.8 Hz
l'excitateur
Qms : Q de l'excitateur à Fs considérant
Qms 10.261 10.282 9.021 9.169 uniquement la résistance non-électrique
Qes : Q de l'excitateur à Fs considérant
Qes 0.756 0.74 0.83 0.824 uniquement la résistance électrique
Qts 0.704 0.691 0.76 0.756 Qts : Q total de l'excitateur à Fs
Pe[max.] : Puissance d'entrée
Pe [max.] (W) 600 W
continue maximum
Xmax. : Déplacement effectif maximum
Xmax. (mm) 14.95 mm 14.8 mm
de la bobine mobile sans distorsion
Réponse en fréquence (Hz) 25 ~500 Hz
Masse de l’aimant (once) 65.4 oz
(g) ( 1854.1 g )
Diamètre de la bobine mobile (pouces) Dia. 2 - 5/32 inch Dia. 2 - 4/32 inch
(mm) ( 54.5 mm ) ( 53.59 mm )
Hvc (mm) 39.9 mm 39.6 mm Hvc : Hauteur de la bobine mobile
Hag (mm) 10 mm Hvc : Hauteur de la bobine mobile
CS-AW7220 CS-AW7240
Paramètres REMARQUES
parallel series parallel series
Impédance nominale (Ω) 2Ω + 2Ω 4Ω + 4Ω
SPL (dB,1W/1M) 85.13 dB 85.2 dB 85.87 dB 85.65 dB SPL : Niveau de pression sonore
Déplacement (Liter) 0.18 ft3
Diamètre du tuou de découpe (pouces) Dia. 10 - 29/32 inch
(mm) ( 277 mm )
Profondeur de montage (pouces) 7 - 6/32 inch
(mm) ( 182.5 mm )
Re : Résistance de la bobine mobile
Re (Ω) 0.98 Ω 3.84 Ω 1.94 Ω 7.61 Ω
en CC
BL : Produit de la densité de flux et de l
BL (T.M) 6.84 13.72 9.56 19.14 a longueur efficace de fil de la bobine
mobile
Vas : Volume d'air égal à la conformité
Vas (Iitre) 38.7 L 38.76 L 35.23 L 35.05 L
de l'excitateur
Vas (CuFt) 1.37 ft3 1.37 ft3 1.24 ft3 1.24 ft3
Me (g) 171.854 g 172.934 g 157.028 g 157.336 g Me : Masse effective
D (mm) Dia. 246 mm D : Diamètre effectif du cône
Fs : Résonance à l'air libre de
Fs (Hz) 34.6 Hz 34.5 Hz 37.9 Hz 38 Hz
l'excitateur
Qms : Q de l'excitateur à Fs considérant
Qms 10.277 10.089 8.931 9.014 uniquement la résistance non-électrique
Qes : Q de l'excitateur à Fs considérant
Qes 0.786 0.765 0.794 0.781 uniquement la résistance électrique
Qts 0.73 0.711 0.73 0.719 Qts : Q total de l'excitateur à Fs
Pe[max.] : Puissance d'entrée
Pe [max.] (W) 600 W
continue maximum
Xmax. : Déplacement effectif maximum
Xmax. (mm) 14.95 mm 14.8 mm
de la bobine mobile sans distorsion
Réponse en fréquence (Hz) 23 ~500 Hz
Masse de l’aimant (once) 86.2 oz
(g) ( 2443.7 g )
Diamètre de la bobine mobile (pouces) Dia. 2 - 5/32 inch Dia. 2 - 4/32 inch
(mm) ( 54.5 mm ) ( 53.59 mm )
Hvc (mm) 39.9 mm 39.6 mm Hvc : Hauteur de la bobine mobile
Hag (mm) 10 mm Hvc : Hauteur de la bobine mobile

- 11 -
 Le agradecemos la adquisición del Altavoz Estereofónico para Automóvil de
ARSENAL. Para efectuar una instalación segura y para que el altavoz funcione
correctamente, lea detenidamente las siguientes instrucciones.

Parts

2. Screw x 10 3. Jump
ESPAŃOL

1. Grille

4. Fuse (10A) x 2 5. Hexagon socket

screw keys

Instalación y uso correctos

1.Antes de conectar los altavoces con el amplificador, confirme que esté cortada la
alimentación eléctrica. El ruido producido al realizar la conexión con la alimentación
conectada puede causar daños en los altavoces.
2.Deben conectares los terminales correspondientes del amplificador y de los
altavoces, es decir izquierdo a izquierdo y derecho a derecho,asi co mo “+” a “+” y
“–” a “–”. Si las polaridades se co nectan inversamente, la reproducción este
reofónica se deteriorará.
3.No someta los altavoces a una entrada excesiva. La capacidad máxima de los
CS-AW7020/CS-AW7040/CS-AW7220/CS-AW7240 es de 600 votios (POTENCIA
MUSICAL R.M.S.). Una entra da excesiva dañará los altavoces.
4.Los CS-AW7020/CS-AW7040/CS-AW7220/CS-AW7240 tienen 2Ω,4Ω,8Ω de
impedancia. Asegúrese de que la impe dancia de salida del terminal para altavoces
de amplificador sea de 2Ω, 4Ω,8Ω.
5.Cuando limpie los altavoces, utilice un paño suave y frote la superficie con cuidado.
No aplique solventes ni diluyentes.
6.Asegurese de seguir cuidadosamente las instrucciones para:
Conecciones de Cable
Reemplazo de fucible
Cambiando el Selector de Resistencia
Instalar el subwoofer y la moldura del anillo
Consulte la Page 19 de este Manual de Instrucciones para los detalles de estos
procedimientos.
- 12 -
Diagramas de Aplicasion Dual 4Ω
JUMPER JUMPER
1 amplificador monofónico 1 amplificador monofónico
1(un) bajo 1(un) bajo
Puente fijado en serie Puente fijado en Paralelo
Carga a 8Ω(4Ω+4Ω) SERIES PARALLEL Carga a 8Ω(4Ω+4Ω) SERIES PARALLEL
Jumper Plug
Jumper Plug

Input Bi-Amp Input Input Bi-Amp Input

+ - Only + - + - Only + -

Mono Mono
4Ω 4Ω 4Ω 4Ω
8Ω 2Ω

*JUMPER is Removed Configuracion Bi-Amplificada *JUMPER is Removed

Amplificador 1,2 ch 2 amplificadores monofónicos
1(un) bajo 1(un) bajo Se quita el puente Carga a 4Ω

ESPAŃOL
Se quita el puente
Carga a 4Ω SERIES PARALLEL SERIES PARALLEL

Input Bi-Amp Input

Mono Input Bi-Amp Input
Stereo + - Only + - + - Only + -
4Ω

Mono
4Ω 2-Chan
4Ω

JUMPER JUMPER
1 amplificador monofónico
2 (Dos) bajos
Puente fijado en serie
Subwoofers wired in Parallel SERIES PARALLEL SERIES PARALLEL
Carga a 4Ω Jumper Plug Jumper Plug

Input Bi-Amp Input Input Bi-Amp Input

+ - Only + - + - Only + -

Mono
4Ω 8Ω 4Ω 4Ω 8Ω 4Ω
4Ω

JUMPER JUMPER JUMPER

1 amplificador monofónico
3 (Tres) bajos
Puente fijado en serie
Subwoofers wired in Parallel SERIES PARALLEL SERIES PARALLEL SERIES PARALLEL
Carga a 2.6Ω Jumper Plug Jumper Plug Jumper Plug

Input Bi-Amp Input Input Bi-Amp Input Input Bi-Amp Input

+ - Only + - + - Only + - + - Only + -

Mono
4Ω 8Ω 4Ω 4Ω 8Ω 4Ω 4Ω 8Ω 4Ω
2.6Ω

JUMPER JUMPER JUMPER JUMPER

1 amplificador monofónico
4 (Cuatro) bajos
Puente fijado en serie
Subwoofers wired in Parallel SERIES PARALLEL SERIES PARALLEL SERIES PARALLEL SERIES PARALLEL
Carga a 2Ω Jumper Plug Jumper Plug Jumper Plug Jumper Plug

Input Bi-Amp Input Input Bi-Amp Input Input Bi-Amp Input Input Bi-Amp Input
+ - Only + - + - Only + - + - Only + - + - Only + -

Mono
4Ω 8Ω 4Ω 4Ω 8Ω 4Ω 4Ω 8Ω 4Ω 4Ω 8Ω 4Ω
2Ω

- 13 -
 Diagramas de Aplicasion Dual 2Ω
JUMPER JUMPER
1 amplificador monofónico 1 amplificador monofónico
1(un) bajo 1(un) bajo
Puente fijado en serie Puente fijado en Paralelo
Carga a 4Ω(2Ω+2Ω) SERIES PARALLEL Carga a 4Ω(2Ω+2Ω) SERIES PARALLEL
Jumper Plug
Jumper Plug

Input Bi-Amp Input Input Bi-Amp Input

+ - Only + - + - Only + -

Mono Mono
2Ω 2Ω 2Ω 2Ω
4Ω 1Ω

*JUMPER is Removed Configuracion Bi-Amplificada *JUMPER is Removed

Amplificador 1,2 ch 2 amplificadores monofónicos
1(un) bajo 1(un) bajo Se quita el puente Carga a 2Ω
ESPAŃOL

Se quita el puente
Carga a 2Ω SERIES PARALLEL SERIES PARALLEL

Input Bi-Amp Input

Mono Input Bi-Amp Input
Stereo + - Only + - + - Only + -
2Ω

Mono
2Ω 2-Chan
2Ω

JUMPER JUMPER
1 amplificador monofónico
2 (Dos) bajos
Puente fijado en serie
Subwoofers wired in Parallel SERIES PARALLEL SERIES PARALLEL
Carga a 2Ω Jumper Plug Jumper Plug

Input Bi-Amp Input Input Bi-Amp Input

+ - Only + - + - Only + -

Mono
2Ω 4Ω 2Ω 2Ω 4Ω 2Ω
2Ω

JUMPER JUMPER JUMPER

1 amplificador monofónico
3 (Tres) bajos
Puente fijado en serie
Subwoofers wired in Parallel SERIES PARALLEL SERIES PARALLEL SERIES PARALLEL
Carga a 1.3Ω Jumper Plug Jumper Plug Jumper Plug

Input Bi-Amp Input Input Bi-Amp Input Input Bi-Amp Input

+ - Only + - + - Only + - + - Only + -

Mono
2Ω 4Ω 2Ω 2Ω 4Ω 2Ω 2Ω 4Ω 2Ω
1.3Ω

JUMPER JUMPER JUMPER JUMPER

1 amplificador monofónico
4 (Cuatro) bajos
Puente fijado en serie
Subwoofers wired in Parallel SERIES PARALLEL SERIES PARALLEL SERIES PARALLEL SERIES PARALLEL
Carga a 1Ω Jumper Plug Jumper Plug Jumper Plug Jumper Plug

Input Bi-Amp Input Input Bi-Amp Input Input Bi-Amp Input Input Bi-Amp Input
+ - Only + - + - Only + - + - Only + - + - Only + -

Mono
2Ω 4Ω 2Ω 2Ω 4Ω 2Ω 2Ω 4Ω 2Ω 2Ω 4Ω 2Ω
1Ω

- 14 -
 Para instalar la caja sellada
Cuando el altavoz no se pueda instalCuando el altavoz no se pueda instalCuando el altavoz no se pueda instalusar MDF—20 mm (3/4 pulg.) como
material para la caja.
CS-AW7020 / CS-AW7040 CS-AW7220 / CS-AW7240
A 15-13/32 inch (391.7 mm) 16-13/32 inch (417.1 mm)
B 15-13/32 inch (391.7 mm) 16-13/32 inch (417.1 mm)
C 11-13/32 inch (290.1 mm) 13-29/32 inch (353.6 mm)
D 9-4/32 inch (232 mm) 10-14/32 inch (275.9 mm)
E 9-23/32 inch (247 mm) 11-10/32 inch (295 mm)
F 4/32 inch (3 mm) 4/32 inch (3 mm)
3 3
G 1.57 ft (0.045 m ) 2.17 ft3 (0.062 m3)
Pantallas acústicas delantera y trasera (x 2)
C B Lados superior e
inferior (x 2)

G : El Volumen interior
A

ESPAŃOL
Lados izquierdo y
derecho (x 2)

Dimensión del
orificio de
montaje
* Tcrnillo: Dia. 4mm x 50mm (x 8) (suministrado)

Para instalar la caja sellada

Lados superior e inferior (x 2)Cuando el altavoz no se pueda instalar en el automóvil, construya la caja sellada recomendada en la tablade
abajo—Asimismo, serecomienda usar
CS-AW7020 / CS-AW7040 CS-AW7220 / CS-AW7240
MDF—20 mm(3/4 pulg.) como material para la caja.
A 15-13/32 inch (391.7 mm) 15-13/32 inch (391.7 mm)
B 18-13/32 inch (467.9 mm) 18-13/32 inch (467.9 mm)
C 13-13/32 inch (340.9 mm) 15-13/32 inch (391.7 mm)
D 9-23/32 inch (247 mm) 10-14/32 inch (275.9 mm)
E 9-23/32 inch (247 mm) 11-10/32 inch (295 mm)
F 4/32 inch (3 mm) 4/32 inch (3 mm)
G 1 inch (25.4 mm) 1 inch (25.4 mm)
H 13 inch (330.2 mm) 14 inch (355.6 mm)
I 13-19/32 inch (345.4 mm) 13-6/32 inch (335.3 mm)
Pantallas acústicas delantera y trasera (x 2) J 1.85 ft3 (0.052 m3) 2.54 ft3 (0.072 m3)

C B Lados superior e
inferior (x 2)

J : El Volumen interior

A Lados izquierdo y
G derecho (x 2)

I H Dimensión del
orificio de
montaje
* Tcrnillo: Dia. 4mm x 50mm (x 8) (suministrado) - 15 -
 CS-AW7020 CS-AW7040
Parámetros NOTAS
parallel series parallel series
Impedancia nominal (Ω) 2Ω + 2Ω 4Ω + 4Ω
SPL (dB,1W/1M) 83.49 dB 83.54 dB 84.02 dB 84.12 dB SPL : Nivel de presión de sonido
Desplazamiento (litro) 0.123 ft3
Diámetro del orificio cortado (pulgada) Dia. 9 - 6/32 inch
(mm) ( 233 mm )
Profundidad de montaje (pulgada) 6 - 14/32 inch
(mm) ( 163.5 mm )
Re : Resistencia de la bobina móvil de
Re (Ω) 0.98 Ω 3.83 Ω 1.92 Ω 7.6 Ω
CC
BL : Producto de densidad de flujo y
BL (T.M) 6.85 13.75 8.68 17.21 longitud efectiva del cable de la
bobina móvil
Vas: Volumen de aire equivalente en
Vas (litro) 17.08 L 16.98 L 18.08 L 18.28 L
conformidad con el excitador
Vas (pies cúbicos) 0.6 ft3 0.599 ft3 0.64 ft3 0.65 ft3
Me (g) 145.986 g 147.109 g 124.084 g 122.443 g Me : Masa efectiva
D (mm) Dia. 202 mm D : Diámetro efectivo del cono
Fs (Hz) 39.6 Hz 39.5 Hz 41.7 Hz 41.8 Hz Fs : Resonancia del aire sin excitador
Qms : Q del excitador a Fs considerando
Qms 10.261 10.282 9.021 9.169
sólo la resistencia no eléctrica
ESPAŃOL

Qes : Q del excitador a Fs considerando

Qes 0.756 0.74 0.83 0.824
sólo la resistencia eléctrica
Qts 0.704 0.691 0.76 0.756 Qts : Total Q dei excitador a Fs
Pe[max.] : Potencia máxima de
Pe [máx.] (W) 600 W
entrada contínua
Xmax. : Máximo desplazamiento
Xmax. (mm) 14.95 mm 14.8 mm
efectivo de la bobina móvil sin distorsón
Respuesta de frec (Hz) 25 ~500 Hz
Masa del imán (oz) 65.4 oz
(g) ( 1854.1 g )
Diám.de la bobina móvil (pulgada) Dia. 2 - 5/32 inch Dia. 2 - 4/32 inch
(mm) ( 54.5 mm ) ( 53.59 mm )
Hvc (mm) 39.9 mm 39.6 mm Hvc : Altura de bobina móvil
Hag (mm) 10 mm Hag : Altura de entrehierro
CS-AW7220 CS-AW7240
Parámetros NOTAS
parallel series parallel series
Impedancia nominal (Ω) 2Ω + 2Ω 4Ω + 4Ω
SPL (dB,1W/1M) 85.13 dB 85.2 dB 85.87 dB 85.65 dB SPL : Nivel de presión de sonido
Desplazamiento (litro) 0.18 ft3
Diámetro del orificio cortado (pulgada) Dia. 10 - 29/32 inch
(mm) ( 277 mm )
Profundidad de montaje (pulgada) 7 - 6/32 inch
(mm) ( 182.5 mm )
Re : Resistencia de la bobina móvil de
Re (Ω) 0.98 Ω 3.84 Ω 1.94 Ω 7.61 Ω
CC
BL : Producto de densidad de flujo y
BL (T.M) 6.84 13.72 9.56 19.14 longitud efectiva del cable de la
bobina móvil
Vas: Volumen de aire equivalente en
Vas (litro) 38.7 L 38.76 L 35.23 L 35.05 L
conformidad con el excitador
Vas (pies cúbicos) 1.37 ft3 1.37 ft3 1.24 ft3 1.24 ft3
Me (g) 171.854 g 172.934 g 157.028 g 157.336 g Me : Masa efectiva
D (mm) Dia. 246 mm D : Diámetro efectivo del cono
Fs (Hz) 34.6 Hz 34.5 Hz 37.9 Hz 38 Hz Fs : Resonancia del aire sin excitador
Qms : Q del excitador a Fs considerando
Qms 10.277 10.089 8.931 9.014
sólo la resistencia no eléctrica
Qes : Q del excitador a Fs considerando
Qes 0.786 0.765 0.794 0.781
sólo la resistencia eléctrica
Qts 0.73 0.711 0.73 0.719 Qts : Total Q dei excitador a Fs
Pe[max.] : Potencia máxima de
Pe [máx.] (W) 600 W
entrada contínua
Xmax. : Máximo desplazamiento
Xmax. (mm) 14.95 mm 14.8 mm
efectivo de la bobina móvil sin distorsón
Respuesta de frec (Hz) 23 ~500 Hz
Masa del imán (oz) 86.2 oz
(g) ( 2443.7 g )
Diám.de la bobina móvil (pulgada) Dia. 2 - 5/32 inch Dia. 2 - 4/32 inch
(mm) ( 54.5 mm ) ( 53.59 mm )
Hvc (mm) 39.9 mm 39.6 mm Hvc : Altura de bobina móvil
Hag (mm) 10 mm Hag : Altura de entrehierro

- 16 -
 ES
h OL
ES inc ] H
h OL /32 mm
nc ] H 7 h
2i m a. .5 n c
/ 3
7 .5 m h Di [ 5 2i
a. inc 8- 0/3 ]
Di [ 5 3/32 m ] 1 -2 mm
8- 2 1
a. [ 29
5
9- 7 m Di
i a. [ 24
D

Dia. 10-14/32 inch [ 265 mm ] Dia. 12-12/32 inch [ 314 mm ]

[ 32.69 mm ]
[ 32.51 mm ]

Dia. 10-26/32 inch [ 275 mm ] Dia. 12-24/32 inch [ 324 mm ]

1-9/32 inch
1-9/32 inch
6-14/32 inch [ 163.5 mm ]

7-7/32 inch [ 182.5 mm ]

Dia. 9-4/32 inch [ 231.96 mm ] Dia. 10-28/32 inch [ 275.94 mm ]

CS-AW7020 CS-AW7220
CS-AW7040 CS-AW7240

- 17 -
Santoprene Surround Multi Mount Smart
Trim Ring
(Patent Pending)

Air Vented Glass Fiber

Aluminum Laminated
Cast Basket Hemp Cone

Integlated Dual-Layer
Cone construction Hemp-Fiber Drive
Cone

Woven Tinsel Lead

(Patent Pending) Dual Diametric
Progressive Spider

Rapid Fire Impedance

Aluminum Voice
Selector Speaker Terminal
Coil Former
( Patent Pending)

Dual Stacked
4 (2+2) Layer Voice Coils Strontium Magnet

Heat Transfer Silicon Heat Transfer Silicon

Aero Vent Bottom Plate

T3 Chassis (Thermal Transfer Technology)

- 18 -
- 19 -
TO OUR VALUED CUSTOMER
THANK YOU FOR PURCHASING THIS JVC PRODUCT.
WE WANT TO HELP YOU ACHIEVE A PERFECT EXPERIENCE.

NEED HELP ON HOW TO HOOK UP?

NEED ASSISTANCE ON HOW TO OPERATE?
NEED TO LOCATE A JVC SERVICE CENTER?
LIKE TO PURCHASE ACCESSORIES?

IS HERE TO HELP!
TOLL FREE: 1(800)252-5722
http://www.jvc.com

Remember to retain your Bill of Sale for Warranty Service.

Do not attempt to service the product yourself

Caution
To prevent electrical shock, do not open the cabinet.
There are no user serviceable parts inside.
Please refer to qualified service personnel for repairs.

EN, FR, SP
© 2007 Victor Company of Japan, Limited Printed in China