Scribd
Upload
25 views

Tutorial 3 Problems

This document contains a tutorial with 6 questions regarding thermodynamics. Question 1 asks about the mechanical energy and power generation potential of wind blowing at 7 m/s and passing through a wind turbine with 80m blades. Question 2 asks about the mechanical power converted to thermal energy when water is pumped from a lower to higher reservoir. Question 3 asks about properties of a steam-water mixture in a rigid tank. The remaining questions ask about properties of refrigerant R-134a and water undergoing various thermodynamic processes in piston-cylinder devices.

Uploaded by

Bhavishya Gupta
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
25 views

Tutorial 3 Problems

This document contains a tutorial with 6 questions regarding thermodynamics. Question 1 asks about the mechanical energy and power generation potential of wind blowing at 7 m/s and passing through a wind turbine with 80m blades. Question 2 asks about the mechanical power converted to thermal energy when water is pumped from a lower to higher reservoir. Question 3 asks about properties of a steam-water mixture in a rigid tank. The remaining questions ask about properties of refrigerant R-134a and water undergoing various thermodynamic processes in piston-cylinder devices.

Uploaded by

Bhavishya Gupta
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

INDIAN INSTITUTE OF TECHNOLOGY KANPUR

ESO 201A: Thermodynamics


(2023-24 I Semester)
Instructor: Dr Avinash Kumar Agarwal

Tutorial 3
---------------------------------------------------------------------------------------------------------------------------

Question 1: At a certain location, wind is blowing steadily at 7 m/s. Determine the


mechanical energy of air per unit mass and the power generation potential of a wind
turbine with 80-m-diameter blades at that location. Also determine the actual electric
power generation assuming an overall efficiency of 30 percent. Take the air density to be
1.25 kg/m3. (Ans. 1078 kW, 323 kW)

Question 2: Water is pumped from a lower reservoir to a higher reservoir by a pump that
provides 20 kW of shaft power. The free surface of the upper reservoir is 45 m higher than
that of the lower reservoir. If the flow rate of water is measured to be 0.03 m3/s, determine
mechanical power that is converted to thermal energy during this process due to frictional
effects. (Ans. 6.8 kW)

Fig. 1
Question 3: A 1.8-m3 rigid tank contains steam at 220°C. One-third of the volume is in
the liquid phase and the rest is in the vapor form. Determine (a) the pressure of the steam,
(b) the quality of the saturated mixture, and (c) the density of the mixture. (Ans. 2320
kPa, 0.0269, 287.8 kg/m3)
Fig. 2

Question 4: 10 kg of R-134a fill a 1.115-m3 rigid container at an initial temperature of –


30°C. The container is then heated until the pressure is 200 kPa. Determine the final
temperature and the initial pressure. (Ans. 14.2°C, 84.43 kPa)

Question 5: 100 kg of R-134a at 200 kPa are contained in a piston–cylinder device whose
volume is 12.322 m3. The piston is now moved until the volume is one-half its original
size. This is done such that the pressure of the R-134a does not change. Determine the
final temperature and the change in the total internal energy of the R-134a.

(Ans. -10.09°C, -110.6 kJ/kg)

Question 6: Water initially at 200 kPa and 300°C is contained in a piston–cylinder device
fitted with stops. The water is allowed to cool at constant pressure until it exists as a
saturated vapor and the piston rests on the stops. Then the water continues to cool until
the pressure is 100 kPa. On the T-v diagram, sketch, with respect to the saturation lines,
the process curves passing through the initial, intermediate, and final states of the water.
Label the T, P, and v values for end states on the process curves. Find the overall change
in internal energy between the initial and final states per unit mass of water. (Ans. 1300
kJ/kg)

Fig. 3

You might also like