PWRSPKR 15W Manual

Download as pdf or txt
Download as pdf or txt
You are on page 1of 4

PWRspkr 15W

www.westmountainradio.com
1020 Spring City Drive
Waukesha, WI 53186
262-522-6503
[email protected]

©2015 West Mountain Radio, All rights reserved. All trademarks are
the property of their respective owners.
Thank you for choosing the PWRspkr 15W. You will find that this
LOUD loudspeaker improves your communications especially in noisy
environments.

The PWRspkr 15W is a loudspeaker containing a 15-watt RMS linear power


amplifier. The amplifier uses an active bandpass filter that limits the audio to
a 300Hz to 3.2kHz bandwidth. This makes it ideal for voice communications.

The PWRspkr 15W comes with two six foot cables. The audio cable plugs
into the 3.5 mm speaker or headphone output of a radio. The Powerpole®
connector plugs into any 12 volt power source.

The volume control allows for setting the audio level for comfortable listening.
The PWRspkr 15W has plenty of gain. It can get very loud and this is useful
in a noisy vehicle.

The PWRspkr 15W is ideal for mobile radio stations for hams, CB radio,
commercial radio, emergency radio, ambulances, police vehicles, and small
public address systems.

Installation
The PWRspkr 15W should be installed in a weather-protected area. If it is for
communication purposes place it near the operator. The cables are six feet
long.

Remove the bracket from the speaker housing. Then secure the bracket to
any flat surface using the supplied screws or other hardware. Re-mount the
loudspeaker, aim it, and securely tighten the knurled nuts.

The audio cable has a stereo 3.5 mm plug. The tip is for the audio, the ring
is not connected, and the sleeve is common. This connector is for mono
audio. When plugged into a stereo source the PWRspkr 15W will play the left
channel audio only; it will not short out the right channel. A stereo extension
cable may be added if needed.

The power cable is fitted with red and black Powerpole® connectors. It should
be plugged into a fused source, such as a RIGrunner power strip connected
to 12 volts. Use a 5 Amp fuse. The Red is plus 12 volts, and Black is common.
An extension cable may be used if needed.

(Powerpole® is a registered trademark of Anderson Power Products)

West Mountain Radio 2 Operating Manual


Operation
Turn on the PWRspkr 15W using the Power/Volume knob . The green LED
will light. Adjust the volume control for the intended listening level.

Note: The radio also has a volume control and it must be turned up for the
PWRspkr 15W to work.

It is possible to use either the radio or PWRspkr 15 W volume as the master.


It is recommended to set one volume control half way up. Then the adjustable
volume control can go both above and below the nominal listening level.

Circuit Description
The PWRspkr uses a 4-inch loudspeaker driven with a 15-watt RMS power
amplifier.

The power amplifier is a class–AB linear amplifier connected as a bridge-


tied-load (BTL). This allows the amplifier to produce 15 watts RMS into 4
ohms audio when powered by 13.8 volts without using an output transformer.
Note that both leads of the loudspeaker driver are “hot” and neither can be
grounded.

The power amplifier integrated circuit has internal protection for overheating
and a short-circuited loudspeaker.

Input audio is applied through a resistive dividing network and coupled to the
pre-amplifier via an isolating transformer. The input resistance is 100 ohms.
There are filter capacitors to remove any rf pickup from the audio line.

The internal pre-amplifier contains an active 300 Hz to 3.2kHz band–pass


filter. Note that the filter permits only “intelligence-energy” to reach the
loudspeaker driver. The “lows” and the “highs” are attenuated and not applied
to the loudspeaker. This is why the sound level can be very high without
damaging the loudspeaker from over excursion or excessive heat.

The loudspeaker sound pressure level (SPL) is 102.5 dB typical at 1 meter


before electronic clipping.

DC power is applied through a ferrite inductor and shunt capacitor to remove


any RF on the power leads. Large electrolytic capacitors further filter the
internal DC for any noise or ripple appearing on the DC power line.

West Mountain Radio 3 Operating Manual


Specifications
Dimensions 5.5 x 4.3 x 2.5 in.
6.5 x 4.7 x 2.7 in. when mounted
Power Requirements 9 to 16 VDC
Current: 2A max w/ 13.8V supply
Quiescent current 90mA typical
Sensitivity 0.83 VRMS produces full output into
4 ohms (1kHz signal, 13.8V supply)
Loudspeaker Driver 4 in. treated paper cone
4 ohm impedance
Rated Power: 20 watts
Power Amplifier - Class AB Linear BTL (bridged-tied-load) circuit
Integrated Circuit 15 watts RMS audio output into 4 ohms when powered by
13.8V supply
Short circuit protected by shut down
Over-heat protected by shut down
Heat sink is the two PCB ground planes
Pre-Amplifier Active four stage filter with gain
Frequency response is flat 300 to 3.2kHz
18 dB/octave high-pass at 300Hz (-3 dB)
18 dB/octave low-pass at 3.2kHz (-3 dB)

PWRspkr 15W Warranty


PWRspkr 15W is warranted against failure due to defects in workmanship or materials
for one year after the date of purchase from West Mountain Radio. Warranty does not
cover damage caused by abuse, accident, misuse, improper or abnormal usage, failure
to follow instructions, improper installation, alteration, lightning, or other incidence of
excessive voltage or current. If failure occurs within this period, return the PWRspkr 15W
or accessory to West Mountain Radio at your shipping expense. The device or accessory
will be repaired or replaced, at our option, without charge, and returned to you at our
shipping expense. Repaired or replaced items are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the PWRspkr
15W or accessory made after the expiration of the warranty period.
West Mountain Radio shall have no liability or responsibility to customer or any other
person or entity with respect to any liability, loss, or damage caused directly or indirectly by
use or performance of the products or arising out of any breach of this warranty, including,
but not limited to, any damages resulting from inconvenience, loss of time, data, property,
revenue, or profit, or any indirect, special incidental, or consequential damages, even if West
Mountain Radio has been advised of such damages.
Except as provided herein, West Mountain Radio makes no express warranties and any
implied warranties, including fitness for a particular purpose, are limited in duration to the
stated duration provided herein.
www.westmountainradio.com
1020 Spring City Drive, Waukesha, WI 53186
tel 262-522-6503 fax 262-522-6504

You might also like