0% found this document useful (0 votes)
291 views3 pages

TOPGNSS GN2336 Test Setting Instruction

Uploaded by

Ricardo Vilhena
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
291 views3 pages

TOPGNSS GN2336 Test Setting Instruction

Uploaded by

Ricardo Vilhena
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

www.topgnss.com sales@topgnss.

com

TOPGNSS GN2336 Test setting instruction


Test tools: Satrack_cli ent_V1.29.154

1.1 General description


Satrack is an evaluation software, providing system integrators and end users with a quick and simple
way to interface with ALLYSTAR GNSS chipsets, modules and boards. It enables easy Satellite tracking,
GNSS messages analyzing, logging data receiving, and graphical representation of signaling, satellite
communication and geographical information.
Satrack is designed to communicate with ALLYSTAR’s Cynosure GNSS receiver via serial port or USB
port. It provides general GNSS functions as well as real time and playback evaluation tools.
The purpose of Satrack is to enable users to:
⚫ Conduct performance tests on ALLYSTAR and other GNSS devices.
⚫ Configure ALLYSTAR GNSS positioning chips and modules.
⚫ Update the firmware on GNSS modules.

1.2 Features
⚫ Control of ALLYSTAR GNSS evaluation kits
⚫ Display of Cynosure Binary Protocol
⚫ Export data files to Google Earth
⚫ Display of NMEA output
⚫ File-logging of NMEA output
⚫ Support for Windows® XP, Windows® 7 and Windows® 8.1

For details on usage, refer to the help file of the installation directory.

1
www.topgnss.com [email protected]

1、Configure NMEA output rate


Note: Send commands to the module through the serial port, and you can set the output
refresh rate of the module (5HZ, maximum support 10HZ)

类目 Category 内容 content 指令( Instruction)


F1 D9 06 42 14 00 00 01 38 35 E8 03 00 00 00 00 00
配置 NMEA 输出率 1HZ 00 00 00 00 00 00 00 00 00 B5 6B
Configure
F1 D9 06 42 14 00 00 05 38 00 C8 00 00 00 00 00 00
NMEA output rate 5HZ 00 00 00 00 00 00 00 00 00 61 05

F1 D9 06 42 14 00 00 0A 38 00 64 00 00 00 00 00 00
10HZ 00 00 00 00 00 00 00 00 00 02 24

2、Start command configuration


Send commands to the module through the serial port to perform cold start, warm start, and
hot start operations on the module

类目 Category 内容 content 指令( Instruction)


启动指令配置 冷启动
Cold start F1 D9 06 40 01 00 01 48 22
温启动
Warm start F1 D9 06 40 01 00 02 49 23
热启动
Hot Start F1 D9 06 40 01 00 03 4A 24
恢复出厂设置
Reset F1 D9 06 09 08 00 02 00 00 00 FF FF FF FF 15 01

3、Configure the baud rate:


Send commands to the module through the serial port to change the output baud rate of the
module (default 115200, 9600)
类目 Category 内容 content 指令( Instruction)
配置波特率 9600 F1 D9 06 00 08 00 00 00 00 00 80 25 00 00 B3 07
Configure the baud rate: 115200 F1 D9 06 00 08 00 00 00 00 00 00 C2 01 00 D1 E0

2
www.topgnss.com [email protected]

4、
类目 Category 内容 content 指令( Instruction)
GGA F1 D9 06 01 03 00 F0 00 00 FA 0F

GLL F1 D9 06 01 03 00 F0 01 00 FB 11

关闭 NMEA 数据 GSA F1 D9 06 01 03 00 F0 02 00 FC 13

Close NMEA data GSV F1 D9 06 01 03 00 F0 04 00 FE 17

RMC F1 D9 06 01 03 00 F0 05 00 FF 19

VTG F1 D9 06 01 03 00 F0 06 00 00 1B

ZDA F1 D9 06 01 03 00 F0 07 00 01 1D

GST F1 D9 06 01 03 00 F0 08 00 02 1F

GNTXT F1 D9 06 01 03 00 F0 20 00 1A 4F

GGA F1 D9 06 01 03 00 F0 00 01 FB 10
GLL F1 D9 06 01 03 00 F0 01 01 FC 12
GSA F1 D9 06 01 03 00 F0 02 01 FD 14
GSV F1 D9 06 01 03 00 F0 04 01 FF 18
RMC F1 D9 06 01 03 00 F0 05 01 00 1A
开启 NMEA 数据 VTG F1 D9 06 01 03 00 F0 06 01 01 1C
Turn on NMEA data ZDA F1 D9 06 01 03 00 F0 07 01 02 1E
GST F1 D9 06 01 03 00 F0 08 01 03 20
GNTXT F1 D9 06 01 03 00 F0 20 01 1B 50

5、Save configuration instructions


After sending the configuration command, send the save command to save the configuration
finally.
类目 Category 指令( Instruction)

保存指令
F1 D9 06 09 08 00 00 00 00 00 2F 00 00 00 46 B7

Save instructions
After sending the configuration command, send the save command to save the configuration finally.

You might also like